ION 7400 User Manual

PowerLogic™ ION7400 series
User manual
7EN02-0374-00
11/2015
www.schneider-electric.com
Legal Information
The Schneider Electric brand and any registered trademarks of Schneider Electric
Industries SAS referred to in this guide are the sole property of Schneider Electric
SA and its subsidiaries. They may not be used for any purpose without the owner's
permission, given in writing. This guide and its content are protected, within the
meaning of the French intellectual property code (Code de la propriété
intellectuelle français, referred to hereafter as "the Code"), under the laws of
copyright covering texts, drawings and models, as well as by trademark law. You
agree not to reproduce, other than for your own personal, noncommercial use as
defined in the Code, all or part of this guide on any medium whatsoever without
Schneider Electric's permission, given in writing. You also agree not to establish
any hypertext links to this guide or its content. Schneider Electric does not grant
any right or license for the personal and noncommercial use of the guide or its
content, except for a non-exclusive license to consult it on an "as is" basis, at your
own risk. All other rights are reserved.
Electrical equipment should be installed, operated, serviced, and maintained only
by qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material.
As standards, specifications, and designs change from time to time, please ask for
confirmation of the information given in this publication.
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar with
the device before trying to install, operate, service or maintain it. The following
special messages may appear throughout this bulletin or on the equipment to warn
of potential hazards or to call attention to information that clarifies or simplifies a
procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates that
an electrical hazard exists which will result in personal injury if the instructions are
not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
DANGER
DANGER indicates a haz ardous situation which, if not avoided, will result in death
or serious injury.
WARNING
WARNING indicates a ha zardous situation which, if not avoided, could result in
death or serious injury.
CAUTION
CAUTION indicates a haz ardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE
NOTICE is used to addre ss pra ctice s not re la te d to phys ica l injury.
Please note
Electrical equipment should be installed, operated, serviced and maintained only
by qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material. A qualified person is one who
has skills and knowledge related to the construction, installation, and operation of
electrical equipment and has received safety training to recognize and avoid the
hazards involved.
7EN02-0374-00 3
Notices
FCC
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that any changes or modifications not expressly approved by
Schneider Electric could void the user’s authority to operate the equipment.
This digital apparatus complies with CAN ICES-3 (B) /NMB-3(B).
About this manual

This manual discusses features of the PowerLogic™ ION7400 series power meter
and provides configuration instructions.
Throughout the manual, the term “meter” refers to all models of the ION7400. All
differences between the models, such as a feature specific to one model, are
indicated with the appropriate model number or description.
This manual assumes you have an understanding of power metering and are
familiar with the equipment and power system in which your meter is installed.
This manual does not provide configuration information for advanced features
where an expert user would perform advanced configuration. It also does not
include instructions on how to incorporate meter data or perform meter
configuration using energy management systems or software, other than ION
Setup. ION Setup is a free configuration tool available for download from
www.schneider-electric.com.
Please contact your local Schneider Electric representative to learn what additional
training opportunities are available regarding the ION7400 meter.
The most up-to-date documentation about your meter is available for download
from www.schneider-electric.com.
Related documents
Document Number
PowerLogic™ ION7400 installation sheet NHA51491
PowerLogic™ ION7403 installation sheet NHA77417
ION Reference 70002–0290

ION device template reference —
4 7EN02-0374-00
Table of Contents
Important information ............................................................................3
Please note ..........................................................................................3
FCC.....................................................................................................4
Safety precautions .................................................................................... 11
Meter overview ..........................................................................................12
ION7400 overview ....................................................................................12
Your meter in an energy management system.......................................12
Measured parameters .........................................................................13
Localization ........................................................................................15
Data display and analysis tools ............................................................15
Supported protocols ............................................................................15
ION Setup device configuration tool......................................................16
Meter types ........................................................................................16
Mounting adaptors ..............................................................................16
Terminal covers ..................................................................................16
Replacement hardware .......................................................................17
Basic setup ................................................................................................18
Default values for commissioning...............................................................18
Meter setup..............................................................................................18
Volts mode .........................................................................................18
PT/CT setup .......................................................................................18
Voltage polarity setup ..........................................................................19
Current polarity setup ..........................................................................19
Nominal values ...................................................................................19
Minimum configuration requirements for basic metering ..............................19
Lost user access ......................................................................................19
Hardware reference ..................................................................................20
Supplemental information..........................................................................20
Meter base...............................................................................................20
Panel meter........................................................................................20
DIN meter ..........................................................................................20
Remote meter display (RMD) ....................................................................21
Mounting adaptors....................................................................................21
Terminal covers ........................................................................................21
Replacement hardware .............................................................................21
LED locations...........................................................................................22
Energy pulsing LED behavior ....................................................................22
Revenue lock LED behavior ......................................................................22
Remote display connection LED behavior...................................................22
Panel-mount meter and remote display mounting and wiring
recommendations.....................................................................................23
Power system wiring .................................................................................23
RS-485 wiring ..........................................................................................23
RS-485 cable .....................................................................................23
RS-485 terminals ................................................................................24
Ethernet communications connections .......................................................24
Option modules overview ..........................................................................24
7EN02-0374-00 5
Maximum number of option modules..........................................................25

USB (integrated display only) ....................................................................25
USB port location......................................................................................25
Meter display .............................................................................................26
Display overview ......................................................................................26
Mode indicator....................................................................................26
Home button.......................................................................................26
Revenue lock icon ....................................................................................27
Alarm icon................................................................................................27
Alarm and status LED indicators ................................................................27
Navigation symbols ..................................................................................28
More screens access ................................................................................29
Overrange indication.................................................................................29
Display screens ........................................................................................29
Display modes ....................................................................................29
Alt mode display menu ........................................................................29
Setup menu .............................................................................................34
Creating custom displays using ION Setup .................................................37
Display scaling .........................................................................................38
Remote display troubleshooting icons ........................................................39
Security.......................................................................................................40
Security overview .....................................................................................40
Standard and advanced security features ...................................................40
Advanced security user configuration ...................................................40
Security configuration process...................................................................40
Communications protocol lockout overview ................................................41
Security recommendations and best practices ............................................41
Password setup........................................................................................42
Changing your meter’s display password using the display ..........................43
Configuring standard security using ION Setup ...........................................43
Configuring users and passwords using ION Setup (advanced security
only) ........................................................................................................44
Loading an existing security configuration file (.scf) using ION Setup ............45
Communications .......................................................................................46
Communications overview ........................................................................46
Configuring communications using the display............................................46
Ethernet...................................................................................................46
Ethernet communications connections .................................................46
Ethernet configuration .........................................................................47
Protocols, ports and connections..........................................................47
Self-discovery over Ethernet ................................................................48
Serial.......................................................................................................49
Serial communications ........................................................................49
Serial protocols and ports ....................................................................50
Communications setup........................................................................50
RS-485 configuration ..........................................................................52
Optical port overview...........................................................................53
Configuring your meter with ION Setup over USB..................................55
ION .........................................................................................................55
Modbus ...................................................................................................56
6 7EN02-0374-00
Key terms...........................................................................................56
Your meter as a Modbus slave on a serial network.................................56
Your meter as a Modbus slave over Ethernet ........................................57
Your meter as a Modbus master with serial Modbus slave
devices ..............................................................................................57
Your meter as a Modbus master with Ethernet Modbus slave
devices ..............................................................................................57
Supported Modbus features.................................................................57
Modbus implementation ......................................................................58
Modbus best practices for serial ...........................................................59
Modbus best practices for Ethernet ......................................................60
Modbus master best practices .............................................................60
Modbus map ......................................................................................60
Ethernet gateway .....................................................................................64
EtherGate ..........................................................................................64
Modbus Ethernet gateway ...................................................................65
FTP .........................................................................................................67
FTP memory allocation........................................................................67
FTP file structure and permissions .......................................................67
FTP filename requirements..................................................................68
Accessing your meter’s FTP server ......................................................68
SNMP......................................................................................................68
Simple Network Management Protocol (SNMP) ....................................68
The meter in an SNMP system.............................................................69
SNMP implementation.........................................................................69
Default SNMP mapping .......................................................................71
IEC 61850................................................................................................74
IEC 61850 implementation ..................................................................74
COMTRADE ............................................................................................76
Configuring COMTRADE waveform recording using ION Setup..............77
Downloading COMTRADE files using ION Setup...................................77
DNP ........................................................................................................78
DNP supported features and default implementation .............................78
Time and timekeeping ..............................................................................79
Time overview ..........................................................................................79
Time synchronization overview ..................................................................79
Supported time synchronization sources ....................................................79
Configuring time information using your meter’s display...............................80
Configuring time and time synchronization using ION Setup ........................80
Maintenance ..............................................................................................83
Firmware and templates............................................................................83
Firmware and template overview..........................................................83
Firmware overview..............................................................................83
Typical workflows................................................................................83
Laptop computer upgrade considerations .............................................84
Firmware upgrade considerations ........................................................84
Test mode ................................................................................................88
Test mode default screens ...................................................................89
Troubleshooting .......................................................................................90
Technical assistance ...........................................................................90
Option module troubleshooting ............................................................90
7EN02-0374-00 7
Meter webpages........................................................................................91
Webpage interface ...................................................................................91
Default meter webpages ...........................................................................91
Accessing the meter’s webpages for data viewing and meter
configuration ............................................................................................92
Viewing files using your meter’s webpages .................................................93
Creating custom webpages for your meter..................................................93
Sample data viewing webpage ..................................................................94
Sample webpage data viewing result....................................................94
Logging ..................................................................................................... 102
Logging overview ................................................................................... 102
Default logging capacity .......................................................................... 102
Log depth configuration........................................................................... 102
Log interval configuration ........................................................................ 103
Data log memory calculations .................................................................. 103
Waveform record memory calculations..................................................... 103
Data logging overview............................................................................. 104
Default data logging configuration ............................................................ 104
Revenue log ..................................................................................... 104
Historic data logs .............................................................................. 105
Loss log ........................................................................................... 105
Harmonics logs................................................................................. 106
Energy/demand log........................................................................... 106
Sag/swell log .................................................................................... 106
EN50160 compliance logs ................................................................. 106
4-30 compliance logs ........................................................................ 107
Event log overview ................................................................................. 108
Default event log configuration................................................................. 108
Waveform recording overview ................................................................. 109
Key terms......................................................................................... 109
Default waveform recording configuration................................................. 110
Configuring waveform recording using ION Setup ..................................... 110
Setpoint learning overview ...................................................................... 111
Learning installation mode and learning duration....................................... 112
Inputs / outputs ........................................................................................ 114
I/O Overview .......................................................................................... 114
Input/output ION modules ....................................................................... 114
Input/output ION modules, ports and labels .............................................. 114
I/O option modules ................................................................................. 116
Analog inputs ......................................................................................... 117
Analog input applications................................................................... 117
Analog input voltage and current mode............................................... 117
Analog input behavior........................................................................ 117
Analog input zero scale and full scale values....................................... 117
Analog outputs ....................................................................................... 118
Analog output applications................................................................. 118
Analog output behavior ..................................................................... 119
Analog output zero scale and full scale values..................................... 119
Digital inputs .......................................................................................... 120
Digital input applications .................................................................... 120
IRIG-B time synchronization .............................................................. 120
8 7EN02-0374-00
WAGES monitoring ........................................................................... 122

WAGES example .............................................................................. 122
Input metering .................................................................................. 122
Digital outputs ........................................................................................ 124
Digital output applications.................................................................. 124
Energy pulsing ....................................................................................... 126
Default energy pulsing LED sources................................................... 126
Alarms and alerts .................................................................................... 129
Alarms overview ..................................................................................... 129
Alarm types............................................................................................ 129
Alarm event priorities .............................................................................. 131
Info only and none event priority......................................................... 131
Alarm indicators ..................................................................................... 132
Default alarms ........................................................................................ 132
Alarm information ................................................................................... 133
Viewing and acknowledging alarms using the meter’s display .................... 133
Alarm configuration................................................................................. 133
Alerting .................................................................................................. 138
Resets....................................................................................................... 139
Meter resets ........................................................................................... 139
Option module reset ............................................................................... 139
Available resets ...................................................................................... 139
Measurements......................................................................................... 143
Power and power factor .......................................................................... 143
Power demand ....................................................................................... 145
WAGES monitoring................................................................................. 146
Incremental energy ................................................................................. 147
Incremental energy example.............................................................. 147
Conditional energy.................................................................................. 148
Trending and forecasting overview........................................................... 149
Power quality ........................................................................................... 151
Power quality overview ........................................................................... 151
Sag/swell overview ................................................................................. 151
Harmonics overview ............................................................................... 151
Voltage crest factor ................................................................................. 152
Crest factor current ................................................................................. 152
K-factor.................................................................................................. 152
Harmonic content calculations ................................................................. 152
TDD calculations .................................................................................... 153
Phasors ................................................................................................. 153
Disturbance direction detection overview.................................................. 153
Verifying accuracy................................................................................... 155
Overview of meter accuracy .................................................................... 155
Accuracy test requirements ..................................................................... 155
Signal and power source ................................................................... 155
Control equipment ............................................................................ 155
Environment ..................................................................................... 155
Reference device or energy standard ................................................. 156
Energy pulsing ....................................................................................... 156
Verifying accuracy test meter settings ...................................................... 156
7EN02-0374-00 9
Verifying accuracy test ............................................................................ 157

Calculate the number of required pulses................................................... 158
Percentage error calculation for accuracy verification testing ..................... 158
Typical sources of test errors ................................................................... 159
Accuracy verification test points ............................................................... 159
Revenue ................................................................................................... 160
Revenue locking..................................................................................... 160
PT/CT correction..................................................................................... 161
Transformer line loss compensation ......................................................... 161
Time of use ............................................................................................ 162
Specifications .......................................................................................... 163
10 7EN02-0374-00
Safety precautions PowerLogic™ ION7400 series
Safety precautions
Installation, wiring, testing and service must be performed in accordance with all
local and national electrical codes.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Apply appropriate personal protective equipment (PPE) and follow safe
electrical work practices. See NFPA 70E in the USA, CSA Z462 or applicable
local standards.
• Turn off all power supplying this device and the equipment in which it is
installed before working on the device or equipment.
• Always use a properly rated voltage sensing device to confirm that all power
is off.
• Treat communications and I/O wiring connected to multiple devices as
hazardous live until determined otherwise.
• Do not exceed the device’s ratings for maximum limits.
• Never short the secondary of a potential/voltage transformer (PT/VT).
• Never open circuit a current transformer (CT).
• Always use grounded external CTs for current inputs.
• Do not use the data from the meter to confirm power is off.
• Replace all devices, doors and covers before turning on power to this
equipment.
Failure to follow these instructions will result in death or serious injury.
NOTE: See IEC 60950-1:2005, Annex W for more information on communications

and I/O wiring connected to multiple devices.
WARNING
UNINTENDED OPERATION
Do not use this device for critical control or protection applications where human
or equipment safety relies on the operation of the control circuit.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
7EN02-0374-00 11
PowerLogic™ ION7400 series Meter overview
Meter overview
ION7400 overview
The PowerLogic™ ION7400 energy and power quality meters help meet the needs
of your energy monitoring and cost management applications.
ION7400 meters comply to international metering accuracy standards. You can
customize your meter by loading specialized frameworks, adding option modules
and incorporating mounting accessories into the physical installation.
Meter features
EN50160 including flicker monitoring
Power quality readings (THD)
Sag/swell capture for voltage and currents
True RMS metering to the 63rd harmonic
Active (kW), reactive (kVAR) and apparent (kVA) power
600 V direct connection on voltage inputs
Minimum/maximum readings of metered data
Transformer and Line Loss Compensation (TLC/LLC)
WAGES support
Time of use support
Trending and forecasting
Time synchronization to 1 ms accuracy
Test mode
ANSI type 2 optical port
USB ports (on meters with integrated display)
Dual port Ethernet (two physical ports, one Ethernet IP address)
Multiple languages supported
Web interface
Configuration through integrated or remote display
Alarms (active and historic) display viewing and acknowledgment
Modbus master and Ethernet gateway protocols supported
Downloadable firmware and templates
Your meter in an energy management system

As a key piece in your energy management system, the meter provides highly
accurate measurements and calculations for a wide variety of power system
values, performs analysis on collected data, alerts you of potential issues and
integrates with a variety of display and analysis software.
12 7EN02-0374-00
Meter overview PowerLogic™ ION7400 series
Inputs / outputs Alarming and

alerting
Highly accurate
metering
Data and event
logging
Powerful
customization
Measure Tre nding a nd
Simple forecasting
configuration
Power quality
monitoring
Understa n d
P owe r Monitoring Easy access

Expe rt
http://meteripaddress
to information
Act
Time of us e
Cost allocation/tenant billing Energy
e fficie ncy
Asset and network Configurable

management security
Perform basic setup using the color LCD display , the meter Configure meter to help protect against unauthorized
webpages or ION Setup configuration of your meter and access to your meter ’s da ta
Improve energy ef ficiency and track compliance to green

Customize meter functionality using the power of ION
standards
Access highly accurate measurements and calculations for a

Help prolong asset life with proactive network management
wide variety of power system values
Use the onboard or extendible I/O for non-critical control, Log data in a number of onboard default logs, or customize
WAGES a nd input me te ring, e ne rgy puls ing a nd s ys te m your meter to log other parameters, and access that
monitoring (for example, breaker status) information using software or webpages
Receive notifications of predefined meter and system events Time of us e a nd pe rform cos t a lloca tion/te na nt billing
or create custom alarms
Tra ck the tre nds for powe r s ys te m va lue s ove r time to Easily access information after basic configuration using:
understand energy usage patterns, optimize network capacity • a variety of industry-standard protocols
and forecast future usage • software such as Power Monitoring Expert and
PowerSCADA Expert
Monitor compliance to a variety of power quality standards
• the meter ’s inte rna l we bpa ge s (s ta nda rd or cus tomize d to
using the meter ’s highly a ccura te me te ring
suite your needs)
Use the meter ’s s e tpoint le a rning fe a ture to le a rn your powe r
• the optional remote display (DIN models)
system’ s normal operating values
• from downstream devices by using the meter as a gateway
Locate disturbances using disturbance direction detection
Measured parameters
Energy
Your meter provides bi-directional 4-quadrant energy metering.
Your meter provides active, reactive and apparent energy values.
• kWh, kVARh, kVAh delivered and received
• kWh, kVARh, kVAh net (delivered - received)
• kWh, kVARh, kVAh total (delivered + received)
• Volt-squared-hours and amp-squared-hours
Energy parameters can be logged automatically on a programmed schedule.
All energy values represent the total for all three phases.
Demand
Your meter supports several demand calculation methods, including block, rolling
block, synchronized and predicted demand.
7EN02-0374-00 13
It can measure demand on any instantaneous value and record peak (maximum)
and minimum demand with time and date information.
• kW, kVAR, kVA demand
• kW, kVAR, kVA peak demand
• Amps, Volts demand
Instantaneous
Your meter provides one second and half-cycle measurements, per phase and
totals for many values.
• Voltage and current
• Apparent power (kVA), active power (kW) and reactive power (kVAR)
• Power factor and frequency
• Voltage and current unbalance
Harmonics
Your meter provides harmonic distortion metering, recording and real-time values
for all voltage and current inputs.
• Individual harmonics (including magnitude and phase angle) up to the 63rd
harmonic
• Total even harmonic distortion (TEHD) and total odd harmonic distortion
(TOHD)
• Total harmonic distortion (THD) or total demand distortion (TDD)
• K-factor, Crest factor
Min/max recording
Your meter records new minimum and maximum data every recording interval for a
variety of values.
• Voltage and current
• kW, kVAR and kVA
• Power factor
• Frequency
• Voltage unbalance
• Plus any measured value
Power quality
Your meter measures and records voltage and current sags and swells.
Your meter also has many power quality related features.
• Disturbance direction detection: this allows the meter to analyze disturbance
(sag/ swell) information to help determine the direction of the disturbance
relative to the meter.
• Setpoint learning: this allows the meter to learn the power quality characteristics
of your system, to help identify what constitutes a sag or a swell.
• COMTRADE: this allows the meter to save waveform data in COMmon format
for TRAnsient Data Exchange (COMTRADE) on its internal FTP server.
Your meter includes the following power quality compliance:
• EN50160: Your meter measures and presents statistics for determining
EN50160 compliance.
• IEC 61000-4-30: Your meter complies with the IEC 61000-4-30 power quality
standard.
14 7EN02-0374-00
• IEC 62586: Your meter complies with the IEC 62586 power quality
standard.
Localization
The meter can be customized to use different regional settings.
Localization settings determine:
• The language used for the display and webpages
• Time, date and digit formats
• Displayed phase labels (123/ABC)
• IEEE (Institute of Electrical and Electronics Engineers) or IEC (International
Electrotechnical Commission) conventions for power, power factor and energy
You can configure your meter’s localization settings through the display or using
ION Setup.
Data display and analysis tools
Display
Use the meter’s display for local monitoring and standalone applications.
The color LCD display lets you view real-time values, events and alarms, and
perform basic device configuration. Connect a remote display to a meter without an
integrated display to view meter data and perform basic meter configuration.
Active and historical alarms

The meter’s display shows an alarm icon and the alarm LED flashes if your meter
detects an active alarm condition.
Depending on the priority of the alarm, your meter’s display also flashes. You can
view and acknowledge active alarms and historic alarms and events through the
display and software webpages. An active alarm becomes a historic alarm when
the alarm condition no longer exists.
Meter internal web server feature

Your meter’s internal web server provides quick and easy access to real-time
energy and basic power quality information without special software using an on-
board web server combined with an Ethernet port.
The built-in web pages display selected energy and power quality information
through the web-enabled device; these pages also support basic meter
configuration.
Email messaging feature

You can configure your meter to automatically email information, whether
notification of a high-priority event or a regularly scheduled send of logged data, to
an external email address.
Specify the type of event that triggers an email alert, such as a power quality
disturbances or interval for logged data. Email messages from your meter are
received like any other email message.
Supported protocols
Your meter’s fundamental protocol and architecture is ION.
You can integrate the meter into various industry-standard networks. Data that the
meter measures can be made available to other devices using Modbus, DNP 3.0
7EN02-0374-00 15
and SNMP as well as the MV-90 translation system. You can configure the meter
to import data from other devices on these networks. Your meter supports the IEC
61850 protocol and COMTRADE waveform data format.
Your meter also supports IPv6, DPWS and RSTP Ethernet protocols.
ION Setup device configuration tool

ION Setup is a free configuration tool for your meter that allows you to remotely
configure your meter’s features over Ethernet or serial communications.
• Use the setup screens to guide you through the process of configuring your
meter.
• Use the real-time data screens to verify your meter’s configuration.
• Use the data screens to view your meter’s recorded data.
• Use the charting function to view your meter’s recorded waveforms.
You can download ION Setup from www.schneider-electric.com.
See the online ION Setup help, available from www.schneider-electric.com, for
instructions on connecting to your meter.
Meter types
The ION7400 series is available in two physical form factors, and has several
accessories.
Model Commercial reference Description
ION7400 METSEION7400 Panel-mounted meter with

integrated display
ION7403 METSEION7403 DIN rail-mounted meter without

display, which can be
connected to a remote display
PM89RD96 METSEPM89RD96 Remote display (for DIN meter

only)
PM89M2600 METSEPM89M2600 Digital I/O option module

(2 out, 6 in)
PM89M0024 METSEPM89M0024 Analog I/O option module

(2 out, 4 in)
PM8000SK METSEPM8000SK Voltage and current sealing kit
METSEPMAK METSEPMAK Mounting adapter kit for remote

display and DIN meter
Refer to your meter’s catalog pages, available from www.schneider-electric.com,

for updated information on meter types and accessories.
Mounting adaptors
There are different mounting adaptor accessories that can help when installing
your meter in existing panels and cutouts where the default mounting hardware is
not appropriate.
Mounting adaptor kits are ordered separately from the meter.
Terminal covers
The voltage and current terminal covers help prevent tampering with the meter’s
voltage and current measurement inputs.
The terminal covers enclose the terminals, the conductor fixing screws and a
length of the external conductors and their insulation. The terminal covers are
secured by tamper-resistant meter seals.
16 7EN02-0374-00
These covers are included for meter models where sealable voltage and current
covers are required to comply with revenue or regulatory standards.
The meter terminal covers must be installed by a qualified installer.
Refer to the Sealing kit instruction sheet for instructions on installing the terminal
covers.
Replacement hardware
You can order replacement mounting and installation hardware for your meter and
accessories.
7EN02-0374-00 17
PowerLogic™ ION7400 series Basic setup
Basic setup
Default values for commissioning
Use these default values the first time you connect to and configure your meter.
Parameter Default value

Display password (also for logging onto meter webpages) 0
Username (for logging onto meter webpages) 7400
IP address 169.254.0.10
Subnet mask 255.240.0.0
Gateway 0.0.0.0
RS-485 Unit ID: 100

Language English
Meter setup
You can configure your meter’s basic metering parameters using the display.
Volts mode
Parameter Values Description
Volts Mode 4W-Wye, Delta, 3W-Wye, The power system’s configuration

Single, Demo
PhaseOrder ABC, ACB The power system’s phase order
PT/CT setup
PT Primary 1 to 999,999.99 The potential transformer’s primary winding

voltage rating
NOTE: PTs are also referred to as a VTs or
voltage transformers.
PT Secondary 1 to 999,999.99 The potential transformer’s secondary winding

voltage rating
NOTE: PTs are also referred to as a VTs or
voltage transformers.
CT Primary 1 to 999,999.99 The current transformer’s primary winding

current rating
CT Secondary 1 to 999,999.99 The current transformer’s secondary winding

current rating
I4 Primary 1 to 999,999.99 The I4 current transformer’s primary winding

current rating
I4 Secondary 1 to 999,999.99 The I4 current transformer’s secondary winding

current rating
18 7EN02-0374-00
Basic setup PowerLogic™ ION7400 series
Voltage polarity setup
Va Polarity Normal, Inverted The polarity of the potential transformer on Va
Vb Polarity Normal, Inverted The polarity of the potential transformer on Vb
Vc Polarity Normal, Inverted The polarity of the potential transformer on Vc
Current polarity setup
Ia Polarity Normal, Inverted The polarity of the current transformer on Ia
Ib Polarity Normal, Inverted The polarity of the current transformer on Ib
Ic Polarity Normal, Inverted The polarity of the current transformer on Ic
I4 Polarity Normal, Inverted The polarity of the current transformer on I4
Nominal values
V Nominal 1 to 999,999 The nominal (normal) voltage of the power

system
I Nominal 1 to 999,999 The nominal (normal) current of the power

system
Nominal 50, 60 The nominal (normal) frequency of the power

Frequency system
Minimum configuration requirements for basic metering

At a minimum, you must configure some parameters to help your meter perform
basic metering functions.
Setup screen Screen Minimum configuration
Meter Setup Volts Mode Volts mode

PT/CT Setup PT, CT and I4 CT primary and secondary
Nominal values V nominal, I nominal, Nominal frequency
NOTE: You must also configure all the parameters related to the meter features
you are using, for example, you must configure the DNS server address if you are
using the meter’s DNS feature.
Lost user access

If you lose your meter’s user access (password) information, contact your local
Schneider Electric representative for instructions on how to return your meter for
factory reconfiguration.
NOTE: Have your meter’s serial number available for reference.
7EN02-0374-00 19
PowerLogic™ ION7400 series Hardware reference
Hardware reference
Supplemental information
This document is intended to be used in conjunction with the installation sheet that
ships in the box with your meter and accessories.
See your device’s installation sheet for information related to installation.
See your product’s technical datasheet at www.schneider-electric.com for the most
up-to-date and complete specifications.
See your product’s catalog pages at www.schneider-electric.com for information
about your device, its options and accessories.
You can download updated documentation from www.schneider-electric.com or
contact your local Schneider Electric representative for the latest information about
your product.
Meter base
Your meter base has two form factors: panel mount with an integrated display and
DIN mount.
Panel meter
A Voltage inputs
B Control power
C Digital inputs (3)
D Revenue lock switch cover

E Digital output
F Gasket
G RS-485
H Ethernet (2)
I Current inputs
J Option module connector
K Display with optical port and USB
Mounting hardware and accessories not shown
DIN meter
A Voltage inputs
B Control power
C Digital inputs (3)
D Revenue lock switch cover

E Digital output
F RS-485
G Ethernet (2)
H Current inputs
I Option module connector
J Remote display connector
20 7EN02-0374-00
Hardware reference PowerLogic™ ION7400 series
Mounting hardware and accessories not shown
Remote meter display (RMD)

The remote meter display can be used with DIN meters.
It has the same buttons and icons as the display on a panel meter, and is powered
by the connection to the meter. A remote display cannot be used with meters that
have an integrated display
D B
C
A Gasket
B Alignment pin location
C Display connection
D Mounting post
Mounting hardware and accessories not shown.
Mounting adaptors
There are different mounting adaptor accessories that can help when installing
your meter in existing panels and cutouts where the default mounting hardware is
not appropriate.
Mounting adaptor kits are ordered separately from the meter.
Terminal covers
The voltage and current terminal covers help prevent tampering with the meter’s
voltage and current measurement inputs.
The terminal covers enclose the terminals, the conductor fixing screws and a
length of the external conductors and their insulation. The terminal covers are
secured by tamper-resistant meter seals.
These covers are included for meter models where sealable voltage and current
covers are required to comply with revenue or regulatory standards.
The meter terminal covers must be installed by a qualified installer.
Refer to the Sealing kit instruction sheet for instructions on installing the terminal
covers.
Replacement hardware
You can order replacement mounting and installation hardware for your meter and
accessories.
7EN02-0374-00 21
LED locations
The LED indicators alert or inform you of meter activity.
A Alarm
08/08/2015 15:33:28 NORM 08/08/2015 15:33:28 NORM B Status
To ta l De m a n d De live re d P e a k De m a n d De live re d
1.439 kW kW s d mx de l 1.439 kW C VAR energy pulsing LEDs
0.661 kVAR kVAR s d mx de l 0.172 kVAR (visible and infrared, integrated display only)
1.584 kVA
1.562
kVA s d mx de l kVA
D Watts energy pulsing LEDs
(visible and infrared, integrated display only)
E Energy pulsing LEDs

(visible and infrared)
VAR WATT
F Revenue lock status

G Remote display connection link
H Remote display connection activity
Related Topics
• Alarm and status LED indicators
Energy pulsing LED behavior

The visible and infrared LEDs are configured by default to pulse based on energy
measured by the meter.
You can configure the pulse weight (pulses per kWh) and the energy source.
Energy pulsing is used to help verify the energy measurement accuracy of your
meter for revenue purposes.
Revenue lock LED behavior

The revenue lock LED indicates the lock status of the meter.
State Description
Off The meter is not revenue locked.

On The meter is revenue locked.
Flashing New revenue lock state is pending; power cycle your meter to set the revenue
lock to on or off.
Remote display connection LED behavior

There are two LEDs in the remote display connector that indicate the state of
communications between the meter and remote display.
22 7EN02-0374-00
LED Description
Green (link) On: link established.

Off: no link established with the remote display. Check the connections to the
remote display and DIN meter.
Yellow (activity) Flashing: active communications between the meter and the remote display.
Off: no communication activity. Check remote display and meter operation.
Panel-mount meter and remote display mounting and wiring

recommendations
There are supplemental mounting and wiring recommendations that apply to
panel-mount meters and remote displays.
• The meter is intended to be mounted inside a ¼-DIN panel cutout.
• Inspect the gasket (installed around the perimeter of the display) and make
sure it is secured properly and not damaged.
• The meter retainer clips, located on either side of the meter base and used to
secure the meter in the panel, do not usually require any tools to install. If
necessary, for panels with limited space, you can use a long-handled slot
screwdriver to help install the meter retainer clips.
• The remote display can only be used with the DIN meter; it cannot be used by
meters with an integrated display.
• The remote display’s power and communications is provided through a single,
direct, point-to-point connection from the remote display to the DIN meter.
Power system wiring

You can connect the meter’s voltage inputs directly to the phase voltage lines of
the power system if the power system’s line-to-line or line-to-neutral voltages do
not exceed the meter’s direct connect maximum voltage limits.
The maximum voltage allowed for direct connection may be lower than the
manufacturer-specified limits, depending on the local electrical codes and
regulations.
If your system voltage is greater than the specified direct connect maximum
voltage, you must use voltage (potential) transformers (VTs/PTs) to step down the
voltages.
RS-485 wiring
Connect the devices on the RS-485 bus in a point-to-point configuration, with the
(+) and (-) terminals from one device connected to the corresponding (+) and (-)
terminals on the next device.
RS-485 cable
Use a shielded 2 twisted pair or 1.5 twisted pair RS-485 cable to wire the devices.
Use one twisted pair to connect the (+) and (-) terminals, and use the other
insulated wire to connect the C terminals
The total distance for devices connected on an RS-485 bus should not exceed
1200 m (4000 ft).
7EN02-0374-00 23
RS-485 terminals
C Common. This provides the voltage reference (zero volts) for the data plus and data minus
signals
Shield. Connect the bare wire to this terminal to help suppress signal noise that may be
present. Ground the shield wiring at one end only (either at the master or the last slave
device, but not both.
- Data minus. This transmits/receives the inverting data signals.
+ Data plus. This transmits/receives the non-inverting data signals.
NOTE: If some devices in your RS-485 network do not have the C terminal, use
the bare wire in the RS-485 cable to connect the C terminal from the meter to the
shield terminal on the devices that do not have the C terminal.
Ethernet communications connections

Your meter’s dual port Ethernet connections enable you to use straight-line or
network loop (ring) topologies.
If local network loop Ethernet topologies are required, you must enable RSTP for
your meter’s Ethernet communications to function.
Only use unshielded CAT5/5e UTP Ethernet cables to wire your meter’s Ethernet
communications. Other cable types may provide an undesired ground path.
NOTICE
EQUIPMENT DAMAGE
Only use unshielded CAT5/5e UTP Ethernet cables.
Failure to follow these instructions can result in equipment damage.
Option modules overview

Option modules are ordered separately from your meter, and can be connected to
your meter without specialized equipment.
Option modules are identified based on the physical order of the attached
modules. The option module attached directly to the meter is module A, the
module attached to module A is module B, and so on. The option module identifier
is added to the ION module name and ION label to uniquely describe each
possible combination of option modules.
A Option module A
B Option module B
C Option module C
24 7EN02-0374-00
D Option module D
E Meter
For example, a meter with two option modules, consisting of an analog option
module directly attached to the meter (A) and a digital option module attached
second (B), describes the Q2 analog output of module A as Port A Q2 and the S3
digital input of module B as Port B S3.
Maximum number of option modules

Depending on the type and quantity of option modules attached to your meter, you
may need to reduce your meter’s maximum operating temperature.
For a panel mount meter, one limitation on the number of modules that can be
attached is the physical strength of the meter mounting hardware. If your meter is
mounted in an area subject to vibration or other physical stresses, your meter’s
ability to physically support multiple option modules and maintain a seal against
the mounting surface may be affected.
NOTICE
EQUIPMENT DAMAGE
Do not exceed the maximum number of option modules.
Related Topics
• Specifications
USB (integrated display only)

Models with an integrated display have USB ports.
You can use the mini–B USB port to connect to a computer running ION Setup to
configure your meter. Other applications, programs and protocols are not
supported.
NOTE: It is not recommended to use your meter’s mini–B USB port to upload
firmware or paste templates because of long file transfer times.
The type A USB port is reserved for future use.
USB port location

The USB ports are located on the meter’s integrated display under a protective
cover.
Flip the USB port cover up to expose the USB ports. Replace the USB port cover
when the ports are not in use to help keep the USB ports clean.
A Mini-B USB
08/08/2015 15:33:28 NORM
Peak Dem and Delivered B Type A USB
kW s d mx de l 1.439 kW
kVAR s d mx de l 0.172 kVAR
kVA s d mx de l 1.562 kVA
WATT VAR
7EN02-0374-00 25
PowerLogic™ ION7400 series Meter display
Meter display
Display overview
The integrated or remote display allows you to view meter data and perform basic
configuration.
The integrated display has USB ports, an optical port and energy pulsing LEDs.
The integrated and remote display screens have the same meter data and setup
screens. Only meters without an integrated display can use the remote display.
NOTE: Your meter’s display backlight dims after a defined period of inactivity.
When the meter detects an unacknowledged active high priority alarm, the display
flashes until the alarm is acknowledged.
Integrated and remote displays
A Date/time
B Mode indicator
08/08/2015 15:33:28 NORM C Revenue lock icon

P e a k De m a n d De live re d D Alarm icon
kW s d mx de l 1.439 kW E Display
kVAR s d mx de l 0.172 kVAR F Navigation icons
kVA s d mx de l 1.562 kVA G Navigation buttons
H Alarm LED
I USB ports cover (integrated display
only)
J Home button
K VAR infrared energy pulsing LED
VAR WATT
(integrated display only)
L VAR energy pulsing LED (integrated

display only)
M Watt infrared energy pulsing LED

(integrated display only)
08/08/2015 15:33:28 NORM
To ta l De m a n d De live re d N Watt energy pulsing LED (integrated
display only)
1.439 kW
O Optical port (integrated display only)

0.661 kVAR
P Status LED
1.584 kVA
Mode indicator
The display mode indicator identifies whether the meter is in normal (Norm),
alternate display (Alt) or test (Test) mode.
Home button
The function of the home button varies depending on the meter’s display mode.
• Norm or test mode: When your meter is in norm or test mode, pressing the
home button returns you to the mode selection screen.
26 7EN02-0374-00
Meter display PowerLogic™ ION7400 series
• Alt mode or setup menu: When your meter is in alternate (alt) display mode or
you are in the setup menu, pressing the home button takes you to the
associated menu screen. If you are in an alt mode data screen, pressing the
home button takes you to the display menu, and pressing home twice takes you
to the summary display screen. If you are in a setup screen, pressing home
takes you to the setup menu, and pressing home again takes you back to the
last display mode data screen.
NOTE: To exit alt display mode, select Normal Display Mode from the alt
display menu in order to access the mode selection screen.
Revenue lock icon

The revenue lock icon indicates the lock status of the meter.
When gray and open, the meter is unlocked. When green and closed, the meter is
locked. You can lock and unlock your meter using the revenue lock switch located
on the body of your meter.
Related Topics
• Revenue locking
Alarm icon
The alarm icon indicates the highest level and state of alarms detected by your
meter.
For example, if the meter detects a low priority and a high priority active alarm, the
alarm icon indicates a high priority active alarm.
NOTE: Alarms can only be viewed and acknowledged through your meter’s
display.
Icon Description
Active alarm indicator:

• Red: high priority alarm state detected
• Yellow: medium priority alarm state detected
• Blue: low priority alarm state detected
The alarm indicator flashes until you acknowledge the alarm.
The alarm indicator changes to the historic alarm indicator of the appropriate
level when the alarm state is no longer detected by the meter.
NOTE: Your meter’s display backlight flashes for unacknowledged high priority
active alarms.
Unacknowledged historic alarm indicator:
• Red: unacknowledged high priority historic alarm
• Yellow: unacknowledged medium priority historic alarm
NOTE: Low priority historical alarms are not indicated.
The active alarm indicator changes to the historic alarm indicator of the
appropriate level when the alarm state is no longer detected by the meter.
No active or unacknowledged high or medium priority historic alarms
Related Topics
• Alarms overview
Alarm and status LED indicators

Your meter has alarm and status LEDs on the display.
7EN02-0374-00 27
These LEDs cannot be configured for other uses.
LED Description
Status Off: unpowered

Steady green: normal operation
Flashing red: no communications (remote display only)
Steady red: firmware upgrade required (remote display only)
Flashing red/green: startup or firmware upgrade sequence in progress
Alarm Off: no active or unacknowledged historic alarms

On: acknowledged active alarm
Flashing: active alarm
NOTE: Your meter’s display backlight flashes for unacknowledged high priority
active alarms.
Related Topics
• LED locations
Navigation symbols
Navigation symbols are displayed on the bottom of the screen above their
corresponding navigation button.
NOTE: If the symbol is gray, that navigation function is not available.
Symbol Description
More
Pressing this button displays additional screens.
Left
Pressing this button moves the displayed cursor one position to the left. If you
are in a more or info screen, it returns you to the previous screen.
Right
Pressing this button moves the displayed cursor one position to the right.
Up
Pressing this button takes you to the previous screen or menu item.
Down
Pressing this button takes you to the next screen or menu item.
Select
Pressing this button selects or confirms the highlighted value.
Cancel
Pressing this button cancels the current selection and returns you to the
previous screen.
Graphic
Pressing this button takes you to a graphical data display.
Numeric
Pressing this button takes you to a numeric data display.
Info
Pressing this button takes you to a detailed information screen.
Edit
Pressing this button allows you to edit the displayed parameter.
28 7EN02-0374-00
Symbol Description
Pressing these buttons allow you to navigate parameter tables in the setup
screens.
Pressing both buttons allows you to perform the described action.
More screens access

You can access additional screens.
Pressing the navigation button associated with the more icon brings up a list of
additional screens related to the displayed screen. Press cancel to remove the list.
If you do not press any button, the list automatically disappears after a short period
of time.
Overrange indication
If any value measured by the meter is too large to fit on the meter’s display, the
meter initially reduces the size of the text to try and make the value fit.
If the value is still too large to be displayed, the meter truncates the value starting
with the least significant digit, and encloses the truncated value in a red box.
Display screens
Display modes
Your meter has three display modes and provides access to your meter’s setup
screens.
Your meter’s display modes are:
• Norm (normal): In norm mode, your meter automatically scrolls through a series
of customizable display screens. You can add or remove norm mode display
screens. If there are no norm mode display screens, the meter displays a
message stating that there are no available screens. To exit norm mode, press
the home button to access the display modes selection screen.
• Alt (alternate): In alt mode, you navigate to view the different data screens. You
cannot modify the default alt mode display screens, but you can add custom
screens. To exit alt display mode, select Normal Display Mode to access the
display modes selection screen.
• Test: In test mode, you manually scroll through a series of default screens. To
exit test mode, press the home button and select Exit Test Mode.
NOTE: In test mode, your meter’s billing quantities stop accumulating and the
data is sent to special test mode registers. These registers are cleared when
you exit test mode.
You can access your meter’s setup screens from the display modes selection
screen or by pressing the home button in alt or test mode. To exit the setup
screens, press the home button.
Alt mode display menu

The alt mode display menu allows you to view data and access the setup menu.
NOTE: Your meter’s menus may appear slightly different than shown depending
on your display settings.
7EN02-0374-00 29
Summary Sample
Summary
Alarms Active Alarms

Historical Alarms
Basic Readings Voltage

Volts L-L Volts ll Average Volts ll Min Volts ll Ma x
Volts L-N Volts ln Average Volts ln Min Volts ln Ma x
Volts Unbalanced
Current I Average I Min (Ia Ib Ic) I Min (I4) I Max ( Ia Ib Ic) I Max ( I4)
Frequency Frequency
Power Power Summary

Power Total Power Total Min Power Total Max
Power Phase A
Power Phase B
Power Phase C
Demand
Total Demand Delivered Peak Demand Delivere d Total TOU P e a k De ma nd De live re d (A-B) TOU P e a k De ma nd De live re d (C-D)
Total Dem and Received Peak Demand Received T otal TOU P e a k De ma nd Re ce ive d (A-B) TOU P e a k De ma nd Re ce ive d (C-D)
Power Factor Power Factor Total Min Power Factor Total M a x
Energy Energy Delivered-Received

Energy Delivered TOU Ene rgy De live re d A&B TOU Ene rgy De live re d C&D
Energy Received
Events Events
Power Quality EN50160

EN50160 Power Frequency Power Frequency Compliance
EN50160 Nominal Supply Voltage
EN50160 Supply Voltage - V1 Voltage Compliance - V 1
EN50160 Supply Voltage - V2 Voltate Compliance - V 2
EN50160 Supply Voltage - V3 Voltage Compliance - V 3
EN50160 Volts Unbalance Volts Unbalance Compliance
EN50160 Volts Harmonics - V1 Volts Harmonics Comp liance - V1
EN50160 Voltage Flicker - V1 Voltage Flicker Compli ance - V1
Harmonics
Voltage THD V1 Harmonics V2 Harmonics V3 Harmonics
Current THD I1 Harmonics I2 Harmonics I3 Harm onics I4 Har monics
Phasors Phasor Diagram
Inputs/Outputs Digital Inputs

Digital Outputs
Analog Inputs
Analog O utputs
Nameplate Nameplate
Custom Screens Cust om s creens
Normal Display Mode Returns to display mode selection screen
Setup Menu See Setup menu section for details
Alternate (alt) mode data display screens

Your meter’s alt mode display screens show measured and calculated information
about the power system being monitored.
NOTE: Minimum, maximum (peak), average and time of use (TOU) values are
typically accessed by pressing the more button to show additional screens.
Menu Menu screens Content

Summary Summary Power system summary
Alarms Active alarms, Active and historical alarms can be viewed and
historical alarms acknowledged.
Basic readings Voltage, current, • Power system voltage (line-to-line or line-to-

frequency neutral), current and frequency values.
30 7EN02-0374-00
Menu Menu screens Content

• Average, minimum and maximum values are also
provided.
Power Power summary, • Per-phase and total kW, kVAR and kVA values,
demand, power factor along with minimum and maximum values.
• Delivered and received demand values including
peak demand.
• Per-phase and total power factor along with
minimum and maximum values.
Energy Energy Energy delivered-received, delivered and received.
Events Events Meter event log entries listing and details.
Power quality EN50160, harmonics, • EN50160 values.

phasors • Voltage and current harmonics, with individual
and total harmonic values.
• Phasor diagram with magnitude and angle
values.
Inputs/outputs Digital inputs, digital Digital and analog I/O values and counts.
outputs, analog inputs,
analog outputs
Nameplate Nameplate Meter model, firmware version and serial number,

along with owner and tag information.
Custom screens — Custom screens

Normal Display — Access to the display mode selection screen.
Mode
Setup Menu — Access to the setup menu screens.
Data viewing using your meter’s display

Use the navigation buttons to view data on your meter’s display.
The following examples show how to use the navigation buttons to view data in
numeric or graphical format, select and view additional menu screens, and view
detailed information about alarms and acknowledge them.
NOTE: Your display may appear differently than shown, depending on your
meter’s power system and display settings.
NOTE: Your navigation icons change color depending on the type of screen being
viewed. If an icon is gray, that navigation option is not available and nothing will
happen when you press the button associated with that icon.
Example: viewing the alarm screens

Use the display navigation buttons to access the alarm screens, display detailed
information, and acknowledge active and historic alarms.
1. Press to display the menu. Press or until Alarms is highlighted. Press
to display the alarm screens. Press until Active Alarms is highlighted.
Press to display active alarms. The Active Alarms title lists, in brackets,
the total number of active alarms.
7EN02-0374-00 31
2. Press or to highlight a specific alarm, in this case an unbalanced
currents alarm. Press to display detailed information about the highlighted
alarm, and press to return to the Active Alarms screen. Press both and
simultaneously to acknowledge all active alarms.
3. Press to display the menu. Press to highlight Historical Alarms. Press
to display historical alarms. The Historical Alarms title lists, in brackets,

the total number of historic alarms.
4. Press or to highlight a specific alarm, in this case a 4-30 voltage
interruption alarm. Press to display detailed information about the
highlighted alarm. Press both and simultaneously to acknowledge all

historical alarms.
5. Press to return to the menu.
Example: viewing the voltage screens

Use the display navigation buttons to view screens, display detailed information,
and display graphical representations of measured voltage data.
1. Press to display the menu. Press or until Basic Readings is
highlighted. Press to view the basic readings screens. Press until
Voltage is highlighted. Press to view the voltage screens. Voltage line-to-

line values are displayed.
2. Press to view a graphical display of historic voltage values, then press
to return to the numeric display. Press to show a list of additional screens.
32 7EN02-0374-00
3. Press or to highlight an additional screen, in this case, Volts II
Average. Press to go to the highlighted screen. Volts II Average displays

the average line-to-line voltage.
4. Press to view a graphical display of average voltage values, then press
to return to the numeric display. Press to return to Volts L-L.
5. Press to view Volts L-N, which also has additional screens and the ability to
view the information in a graphical format.
6. Press again to view Volts Unbalanced. This is the last voltage screen, so
is grayed out and unavailable. Press to return to Volts L-N, and press
again to return to Volts L-L.
7EN02-0374-00 33
Setup menu
Meter configuration can be performed through the display.
You must have your meter’s security settings configured to allow front panel
(display) programming in order to set up the meter using the display.
NOTE: Your display may appear differently than shown, depending on your
meter’s power system and display settings.
NOTE: Some setup parameters cannot be configured when revenue security is
enabled.
Meter Setup Sample

Volts Mode
Sample
PT/CT Setup
Sample
Voltage Polarity Setup
Sample
Current Polarity Setup
Sample
Nom inal Values
Communications Setup IP Address Setup

Ethernet Setup
DNS Setup
COM1 Setup
COM2 Setup
COM3 S e tup
NTP Addre s s
S MTP Addre s s
Display Setup S cre e n S e tup

La be l & S ymbol S e tup
Nume ric Forma t S e tup
Date/Time/Clock Setup Da te & Time S e tup

Clock S etu p
Alarm Setup Alarm S e tup
Language Setup Language Setup
Time of Use Setup TOU Active Ra te s

TOU S e a s on
Resets Re s e ts
Password Setup P a s s word S e tup
Meter setup using your meter’s display

Use the navigation buttons and displayed parameters to configure your meter.
The following example shows how to use the navigation buttons to select
parameters, enter numeric information or select parameter values from lists.
NOTE: Your display may appear differently than those shown, depending on your
meter’s power system and display and localization settings.
34 7EN02-0374-00
NOTE: Your navigation icons change color depending on the type of screen being
viewed. If an icon is gray, that navigation option is not available and nothing will
happen when you press the button associated with that icon.
NOTE: Your meter goes back to displaying data after a period of inactivity in the
setup menu screens.
NOTE: Your meter locks you out of display configuration after you have exceeded
the maximum number of attempts to enter an password.
Your meter’s default display password is 0 (zero).
Example: setting volts mode and PT/CT ratios

Use the display navigation buttons to set your meter’s volts mode and PT ratios.
NOTE: Potential transformers (PT) are also known as voltage transformers (VT).
1. Press to display the menu. Press until Setup Menu is highlighted. Press
to display the Setup Menu. The Setup Menu lists the setup selections on
your meter.
2. Press or to highlight the different setup menu selections. Highlight
Meter Setup and press to select the meter setup screens. The Volts Mode
setup screen is displayed.
3. Press to highlight Volts Mode. Press to edit the volts mode. The Enter
Password screen is displayed.
4. Press to change the value of the highlighted digit (0 - 9). Press to go to
the next digit. Press to enter your password. The Volts Mode configuration
screen is displayed.
7EN02-0374-00 35
5. Press or to highlight the desired volts mode from the list, in this case,
3W-WYE. Press to select the highlighted volts mode. A confirmation screen

is displayed, showing your meter’s previous setting and newly selected setting.
6. Press to confirm, and the new setting is applied to your meter. Press to
cancel and maintain your meter’s original setting.
7. In the Volts Mode screen, press to go to the PT/CT Setup screen.
8. In the PT/CT Setup screen, press to highlight the potential transformer
(PT) or current transformer (CT) value for editing. Press to edit the
highlighted value.
NOTE: If you have exceeded the password timeout period, you are prompted to
enter your meter’s display password.
9. Press to change the value of the highlighted digit (0 - 9). Press to go to
the next digit. Press to enter the new value. When the confirmation screen
is displayed, press to confirm the new value or to revert to the original

value.
Related Topics
• Security overview
• Minimum configuration requirements for basic metering
Display setup
You can configure your meter’s basic display parameters using the display.
36 7EN02-0374-00
Screen setup
Backlight 0 to 720 Specifies how many seconds the display’s

Timeout backlight remains lit after the last button press
Label & symbol setup
Phase Lbls ABC, 123 Sets the voltage and current phase labels
Measurement IEEE, IEC Specifies whether IEEE or IEC measurement

Symbols symbols are applied to displayed values
PF Convention IEEE, IEC Specifies whether IEEE or IEC power factor

conventions are applied to displayed values
Numeric format setup
Digit Grouping 1000.0, 1,000.0, 1 000,0 Specifies how digits are grouped for display
Volts Resolution 1., 1.X, 1.XXX, 1.XXXX Specifies the number of decimal places
displayed for voltages
Current 1., 1.X, 1.XXX, 1.XXXX Specifies the number of decimal places
Resolution displayed for currents
Power Resolution 1., 1.X, 1.XXX, 1.XXXX Specifies the number of decimal places
displayed for power and energy measurements
Language setup
Select the language to be shown on the meter’s display.
By default, your meter has the following languages:
• English
• Spanish
• French
• German
• Italian
• Portuguese
• Russian
• Chinese (simplified)
Creating custom displays using ION Setup

You can use ION Setup to create new custom displays.
1. Start ION Setup.

2. Open the Setup Assistant for your meter.
3. Navigate to Displays.
4. Select Displays from the Front Panel tab and click Edit.
ION Setup loads your meter’s display information into the Display Editor
screen.
7EN02-0374-00 37
5. Select the display mode of the custom screens from the dropdown list, and
rename, delete, or change the order of custom displays.
a. Click New to add a new display screen in the selected display mode.
b. Click Edit to bring up the Display setup screen, where you can configure
new or existing custom displays.
6. Configure your screen.
• Screen Type: Specify the number of parameters displayed on the screen.
• Screen Title: Enter the title to be shown at the top of your custom display.
7. Click Edit to select the displayed parameters.
The number of parameters displayed is determined in the Screen Type
selection described above.
8. Select your digit display properties.
• Resolution: Specifies the number of decimal places displayed.
• Last Digit: Specifies if the last digit is rounded or truncated.
9. Click Send to save the changes in the meter.
Display scaling
You can customize the units for metered values shown on the display and
webpages.
You can configure the units for voltage, current, power and energy values shown
on your meter’s display and webpages from their default units, and you can set the
resolution for the meter’s display. To identify which values will have the modified
units, refer to the display and web units information in your meter’s Modbus map,
available from www.schneider-electric.com.
Configuring display units scaling using ION Setup

You can customize the units for metered values shown on the display and
webpages using ION Setup.
Configuring display units scaling is an advanced procedure that requires in-depth
knowledge of your meter, its underlying architecture, and the system in which it is
installed.
To identify which values will have the modified units, refer to the display and web
units information in your meter’s Modbus map, available from
NOTE: Custom units and resolution settings are automatically adjusted for current
and voltage values to help prevent your meter’s display from showing incorrect
zero values.
1. Start ION Setup.

2. Connect to your meter in advanced mode.
3. Navigate to the Display Options Modules folder and double-click on the module
in the righthand pane.
The Display Options screen is displayed.
4. Select the Setup Registers tab.
5. Select the display units you want to configure: Voltage Units, Current Units,
Power Units or Energy Units. Click Edit.
A unit selection screen is displayed.
6. Select the desired units from the dropdown list, and click OK.
38 7EN02-0374-00
7. When you have finished configuring the display units, click Send to send your
changes to the meter and close the Display Options screen.
See the ION Reference, available from www.schneider-electric.com, for more
information about the Display Options module and your meter’s ION
architecture.
Remote display troubleshooting icons

Your meter’s remote display shows troubleshooting icons in addition to the meter’s
status LED information.
Icon Description
Your remote display cannot communicate to your meter. Check the

connection between your meter and the display. Check the meter’s
status LED to confirm that the meter is operating normally.
Your remote display needs updated firmware for compatibility with

your meter.
Your remote display is undergoing a firmware upgrade. Do not

disconnect your remote display from your meter.
7EN02-0374-00 39
PowerLogic™ ION7400 series Security
Security
Security overview
You can configure standard or advanced security on your meter, as well as optional
revenue security.
Your meter comes with configurable security that you can set to either standard or
advanced, which helps protect against unauthorized configuration of your meter
and access to your meter’s data through the meter’s display or communications.
Your meter has features that allow you to enable/disable Ethernet protocols and
port numbers. Your meter also supports revenue locking, which incorporates
revenue security on all revenue-related parameters and revenue sealing.
Your meter ships from the factory with standard security enabled.
Standard and advanced security features

Security allows you to configure security features on your meter.
Parameter Standard/ Details

advanced
Meter password Standard/ The meter’s password is used to confirm user access when
advanced configuring the meter through the display or over
communications.
The default meter password is 0 (zero).
Active web server Standard/ This option allows you to enable or disable your meter’s
advanced webpages.
Allow web server Standard/ This option allows you to enable or disable the ability to
programming advanced configure your meter using the meter’s webpages.
NOTE: To enable Allow web server programming, you
must have active web server enabled.
Allow Modbus Advanced only This option can only be enabled in advanced security and
programming is disabled for standard security.
Allow front panel Standard/ This option allows you to enable or disable the ability to
programming advanced configure your device using the display.
Allow Advanced only This option can only be disabled in advanced security and
broadcasting is enabled for standard security.
time
synchronization
Protocol lockout Standard/ This option allows you to configure the number of access
advanced attempts before lockout, lockout duration and meter access
event priorities.
Advanced security user configuration

Advanced security allows you to configure users with specific access levels and
passwords.
Security configuration process

The security configuration process has four basic steps: review security
recommendations, set basic security options, configure communications protocol
lockout settings, and configure users.
1. Review security recommendations
2. Set basic security options
• Change the display (front panel) password.
• Disable broadcasting time synchronization (advanced security only).
40 7EN02-0374-00
Security PowerLogic™ ION7400 series
• Enable/disable display (front panel) and Webserver programming.

• Enable/disable Modbus programming (advanced security only).
3. Configure communications protocol lockout options
a. Configure protocol-specific settings:
• Set the number of attempts before the protocol is locked out.
• Set the session timeout.
b. Configure global lockout settings:
• Enter a lockout duration.
• Set the priority of meter access events.
4. Configure users (advanced security only)
• Determine user access.
• Set user passwords.
Communications protocol lockout overview

The communications protocol lockout security feature allows you to set the number
of invalid login attempts that each user can make using a particular protocol and
communications method before being locked out (a user is defined as a user login
and password combination).
For protocols that are not session-based (ION), you can configure how often the
device registers invalid login attempts by configuring the session timeout. You can
also configure the lockout duration for all configurable protocols.
NOTE: If protocol lockout is set to 0 (zero) there is no limit to the number of invalid
login attempts and the protocol will never be locked out. However, the invalid login
attempt events are recorded if the meter access events are configured to record
invalid access attempts.
Session timeout specifies the active duration for a protocol; during this time,
repeated invalid login attempts using the same USER/password combination are
not registered (repeated invalid attempts with different combinations are still
registered). Session timeout only applies to protocols which are not session-based
and send credentials with each packet, and should be configured to help prevent
accidental lockouts and filling the meter’s event log with protocol access events.
Once a user is locked out, the device will not accept login attempts from that user
on that protocol and communications method until the lockout duration has
passed. Invalid login attempts accumulate until the user has completed a valid
login or been locked out. For example, once USER01 has been locked out using
ION over Ethernet, USER01 cannot access the device using ION over Ethernet
until the lockout duration has passed, even if USER01 enters the correct
password. However, if the user enters the correct USER/password combination
before being locked out, the invalid attempt counter is reset to zero. Even if the
user is locked out using ION over Ethernet, that user can still access the device by
entering the correct USER/password combination over a different protocol and
communications method (for example, connecting to the device’s RS-485 serial
port using Modbus protocol).
Related Topics
• Configuring standard security using ION Setup
Security recommendations and best practices

Recommended security configuration
There are recommended security configuration settings to help improve security on
your meter.
7EN02-0374-00 41
• Ensure that your meter requires a password for configuration through the
display or communications.
• Configure the protocol lockouts to help minimize access to your meter.
• Enable advanced security on your meter.
◦ Configure users and passwords to help minimize access to your meter.
• Save a copy of your meter’s ION Setup security configuration (*.scf) file in a
secure location for future reference or troubleshooting. Your meter’s security
configuration file can be loaded onto other meters of the same type to configure
their security settings.
Password best practices

There are recommended password best practices to help improve security on your
meter.
• Change your meter’s display (front panel) password from the default value.
• Make your meter’s display and user-specific passwords as complex as
possible.
NOTE: Make sure that the user password you enter is compatible with the
software used to communicate with your device.
• Schedule regular changes to your meter’s display and user passwords.
• Record your meter’s display and user passwords in a secure location.
If your meter’s user access information is lost, you must return the meter to the
factory, where your meter is reset to its factory defaults and all logged data is lost.
NOTICE
DATA LOSS
Record your device's user and password information in a secure location.
Additional security recommendations

There are additional security recommendations to help improve security on your
meter.
• Disable communications for all unused Ethernet network protocols.
• For the highest level of security, use a revenue-locked meter with advanced
security enabled and configured for minimum access.
• Save a copy of your meter’s security configuration (*.scf) file in a secure
location for future reference or troubleshooting. Your meter’s security
configuration file can be loaded onto other meters of the same type to configure
their security settings.
• Set your meter’s time synchronization source to a secure communications port,
and disable time synchronization on all other ports.
Related Topics
• Protocols, ports and connections
Password setup
It is strongly recommended that you change your meter’s display (front panel)
password from the default value of 0 (zero).
If your meter’s user access information is lost, you must return the meter to the
factory, where your meter is reset to its factory defaults and all logged data is lost.
42 7EN02-0374-00
NOTICE
DATA LOSS
Screen title Parameter Values Description
Password Setup Password 0 to 99999999 Sets the password that must be

entered in order to configure
parameters using the meter’s display
NOTE: This is also the password used
to access the meter’s webpages when
standard security is enabled
Changing your meter’s display password using the display

You can change your display password using your meter’s display.
NOTE: The display password is also used as the webpage password if standard
security is enabled.
1. Go to Setup Menu > Password Setup.

2. Configure your meter’s display password.
Configuring standard security using ION Setup

You can fully configure standard and advanced security on your meter using ION
Setup.
In order to change security settings, you must be logged into ION Setup with an
appropriate ION Setup user level. You must also have the appropriate meter-level
security access to configure meter security.
1. Start ION Setup.

3. Navigate to Security. Select Security Mode and click Edit. The open dialog box
appears.
4. Select the appropriate security configuration file (*.scf) to configure your meter:
– Standard: allows you to configure basic security and communications
protocol lockout.
– Advanced: includes the standard security features and adds user access/
password security settings.
5. The standard options or advanced options configuration screen appears.
Configure the security parameters as required, some parameters can only be
configured using advanced security.
Click Next to configure protocol access information. The protocol lockout
6. In the protocol lockout screen select the protocols that you want to be protected
by the protocol lockout function. Select each protocol and click Edit to configure
the protocol-specific parameters.
7. Enter the lockout duration (in minutes).
8. Click Events to configure user access event priorities. The Event Priorities
screen appears.
9. Configure the user access event priorities.
7EN02-0374-00 43
10.If you have selected standard security, click Finish. You are prompted to save
your security configuration to a file which can be loaded onto other meters.
NOTE: If you chose to save your security file, enter a descriptive name and
click Save. It is recommended that you do not overwrite the default security
files.
If you have selected advanced security, click Next to configure user access and
passwords.
Security parameters available using ION Setup
Parameter Standard/advanced Details

Meter password Standard/advanced Default meter password is 0 (zero).
Active web server Standard/advanced This option allows you to enable or disable your meter’s webpages.
Allow web server Standard/advanced This option allows you to enable or disable the ability to configure your meter using
programming the meter’s webpages.
NOTE: To enable allow web server programming, you must have active web
server enabled.
Allow Modbus Advanced only This option can only be enabled in advanced security and is disabled for standard
programming security.
Allow front panel Standard/advanced This option allows you to enable or disable the ability to configure your device
programming using the display.
Allow broadcasting time Advanced only This option can only be disabled in advanced security and is enabled for standard
synchronization security.
Protocol-specific security parameters available using ION Setup
Protocol lockout 0 - 255 The number of invalid login attempts before access is denied.
If protocol lockout = 0, there is no limit to the number of invalid login attempts and
the protocol will never be locked out.
Session timeout 1 - 43200 minutes (30 The interval between access checks for non-session based protocols.
days)
Related Topics
• Configuring network communications using ION Setup
• Recommended security configuration
Configuring users and passwords using ION Setup (advanced

security only)
Use ION Setup to configure users and passwords.
You must have configured the standard security settings on your meter using ION
Setup.
This task assumes that you are in the user configuration screen in the security
wizard in ION Setup.
1. In the user/passwords screen, select (check) the user that you want to
configure to view the user access options.
2. Select the appropriate values to configure the user’s access.
Some access levels require that multiple access options be selected.
3. Select the user and click Password. The password entry screen appears.
44 7EN02-0374-00
4. Enter the desired password and click OK.

5. Continue configuring user access and passwords for each unique user of the
meter.
NOTE: Select Show password when user selected to display the password
associated with that user. This feature is intended to help ensure that the
correct password is entered for each user.
6. Click Finish to save your security configuration to the meter. You are prompted
to save your security configuration to a file which can be loaded onto other
meters.
NOTE: If you chose to save your security file, enter a descriptive name and
click Save. It is recommended that you do not overwrite the default security
files.
Access Description
Time sync The user can set the meter’s time and time synchronization parameters.
Read The user can view all parameters except the security configuration.
Peak demand The user can reset peak demand values.

reset
Test mode The user can put the meter into test mode (not applicable to all devices).
Full meter config The user can configure all aspects of the meter except demand resets, test
mode or security.
Security config The user can configure security.
Loading an existing security configuration file (.scf) using ION

Setup
You can load an existing security configuration file (*.scf) onto your meter using
ION Setup.
The *.scf file can be a configuration for either standard or advanced security and
must be from the same model of meter.
1. Start ION Setup.

3. Navigate to Security. Select Security Mode and click Send. The Open dialog
box appears.
4. Navigate to the location of the *.scf file you want to load onto your meter. Select
the *.scf file and click Open. The *.scf file is loaded onto your meter.
7EN02-0374-00 45
PowerLogic™ ION7400 series Communications
Communications
Communications overview
Your meter supports several different protocols over its Ethernet and serial
connections.
Your meter’s default protocol implementation meets the needs of most systems
with only basic configuration. You can customize these implementations to meet
your specific needs; these are advanced procedures that require an understanding
of your meter’s architecture, the supported protocols, and the communications
network and power system that your meter is connected to.
Configuring communications using the display

You can configure your meter’s basic communications settings using the display.
Before configuring Ethernet parameters, make sure you obtain your meter’s IP
address and other network information from your network administrator or IT
department.
Before configuring serial parameters, make sure you have a unique unit ID for your
meter and know the serial network settings (protocol, baud rate, parity and stop
bits).
1. Go to Setup Menu > Communications Setup > IP Address Setup.

2. Configure your meter’s IP Address and other network information as required.
NOTE: Your meter’s default IP address is 169.254.0.10
3. Press the down button to access the next screen of meter communications
settings and configure as required.
Ethernet
Ethernet communications connections
The meter supports a single IP address on both of its two physical Ethernet
connections.
You cannot connect your meter to two different Ethernet networks.
Your device’s second Ethernet port acts as an Ethernet switch to help simplify
network connections and reduce installation time and costs, by having shorter
Ethernet cable runs between devices without needing additional Ethernet routers
or repeaters. Your Ethernet connection source should be installed in a location that
helps minimize the overall Ethernet cable routing length and complexity of your
network.
Each of your device’s Ethernet ports has full transmit/receive bandwidth: this
means they do not split the signal, so connecting both of your device’s Ethernet
ports should not impact your communications speed.
Ethernet LED behavior

Your meter has two LEDs that indicate the status of its Ethernet communications.
Link (data rate) On: valid Ethernet connection

• Yellow: data rate is 10 Mbps
• Green: data rate is 100 Mbps
Act (activity) Flashing green: data is being transferred
46 7EN02-0374-00
Communications PowerLogic™ ION7400 series
Ethernet configuration
In order to use Ethernet communications, you must configure your device’s IP
address; you must also configure the subnet and gateway information if required
by your network.
NOTE: For meters that do not have a display, you must configure each one
separately in order to set a unique IP address for each device.
You need to enter network information for any Ethernet servers used by the device.
NOTE: Contact your network system administrator for your IP address and other
Ethernet network configuration values.
Configure your device’s Ethernet settings by using the display or directly
connecting to your meter and using a web browser to access the device’s
webpages. Modify your meter’s Ethernet settings to those provided by your
network system administrator before connecting the device to your local area
network (LAN).
After the meter’s Ethernet port is configured and connected to the LAN, you can
use ION Setup to configure other meter setup parameters.
Protocols, ports and connections

The Ethernet protocols supported by your device allow simultaneous connections
through the IP service ports.
Protocol Port (default) Number of

connections
ION 7700
DNP 20000
81
Modbus TCP 502
Modbus RTU over Ethernet 7701
Modbus TCP (dedicated) 502 32
EtherGate 7801 1
FTP 21 (20) 2
Webserver (HTTP)2 80 10
SNMP 161 N/A

SMTP server (email) outgoing only 25 1
NTP 123 1
IEC 61850 102 4
1These 8 simultaneous connections can be used by ION, Modbus TCP, Modbus RTU over Ethernet,
or DNP. You can have a maximum of 3 DNP connections.
2This is used for the meter’s webpages.
By enabling or disabling TCP/IP protocols, you can control whether or not your
meter accepts new socket connection requests from the TCP/IP protocols
supported by the meter. Changing settings does not impact existing connections.
Depending on the protocol, you can also change the port number.
If you configure communications so that you cannot communicate to and configure
your meter, you must return the meter to the factory, where your meter is reset to
its factory defaults and all logged data is lost.
NOTICE
DATA LOSS
Ensure you maintain sufficient access to communicate to and configure your
device.
Failure to follow these instructions may result in data loss.
7EN02-0374-00 47
Related Topics
• Configuring network communications using ION Setup
• Supported protocols
Ethernet topologies
When wiring your meter’s Ethernet communications, it is recommended to only use
straight-line topology.
If local network loop or ring Ethernet topologies are required, you must enable
RSTP (rapid spanning tree protocol) for your meter’s Ethernet communications to
function.
Self-discovery over Ethernet

Your meter supports DPWS (devices profile for web services) which allows for self-
discovery of the meter when directly connected on IPv6 local area networks.
When you connect your meter directly to your computer, your meter automatically
appears on the network. By default, the meter is named <meter type>_<last six
digits of MAC address>.
NOTE: You do not need to configure your meter’s IP address for self-discovery
over Ethernet; an IPv6 address is automatically generated from your meter’s MAC
address and self-discovery takes place over IPv6.
Double-clicking the meter’s network icon takes you to the meter’s webpages,
where you can view data and perform basic meter configuration.
NOTE: For self-discovery, the meter must be connected directly to the computer
using only a cable or switches, and not by a router.
For example, a meter with a MAC address of 0060784173393 appears on the

network as <meter type>_173393.
Configuring network communications using ION Setup

You can configure your device’s Ethernet settings using ION Setup.
If you are connected to your device over Ethernet, changing Ethernet configuration
parameters without another method of configuration enabled may cause loss of
communications with your device and render it inoperable. In this case a factory
reconfiguration of your device is required, which resets your device to its factory
defaults and all logged data is lost.
NOTICE
DATA LOSS
1. Start ION Setup.

2. Open the Setup Assistant for your device.
3. Select Communications > Network Settings and click the TCP/IP tab.
48 7EN02-0374-00
4. Select a setting and then click Edit. Configure the settings (for example, IP
address, subnet or gateway) to match your communications system.
Parameter Value Description
Ethernet device name configurable This name is associated with

your meter when using
DPWS.
By default, it is the meter type
and the last 6 characters of its
MAC address.
Enable IPv6 Yes/no Specifies if IPv6 is enabled or
disabled.
IP address Contact your local network The Internet protocol address
administrator for parameter of your device.
values.
SubnetMask The Ethernet IP subnetwork
address of your network.
Gateway The Ethernet IP gateway

address of your network.
Rx timeout configurable Specifies the number of

seconds the meter waits for
communication
acknowledgments.
Modbus TCP Idle Timeout configurable Specify number of seconds

the meter waits before
disconnecting an idle Modbus
TCP connection.
Modbus Gateway Disabled/COM1 Specify the port on which
Modbus Gateway sends/
receives Modbus TCP
requests.
NOTE: For Modbus gateway
to function properly, the serial
port protocol must be set to
Modbus Master.
MAC address Read-only The media access control
(MAC) address is factory set
and is for reference only.
5. Click the Protocols tab.

6. Select a protocol and then click Edit. Select whether the protocol connection
requests are accepted by the meter, and configure the port number. Existing
connections are not affected, but any new connections must comply with the
meter’s latest settings.
NOTE: The protocol port number is not configurable on all protocols.
Related Topics
• Configuring standard security using ION Setup
Serial
Serial communications
The meter supports serial communications through its RS-485, optical and USB
ports.
RS-485
In an RS-485 network, there is one master device, typically an Ethernet to RS-485
gateway. It provides the means for RS-485 communications with multiple slave
devices (for example, meters). For applications that require only one dedicated
computer to communicate with the slave devices, a USB to RS-485 converter can
be used to connect to the master device.
7EN02-0374-00 49
Up to 32 devices can be connected on a single RS-485 bus.
Optical
Your meter’s integrated display has an optical port used for communicating with
your meter using an optical probe. Your meter’s optical port can also be configured
for energy pulsing.
USB
Your meter’s integrated display has a mini-B USB port which is used to configure
your meter with a computer running ION Setup.
Serial protocols and ports

Your meter supports serial communications protocols on its RS-485, optical and
USB ports.
Protocol RS-485 Optical USB
ION Y Y Y
Modbus RTU Y Y —
Modbus Master Y — —
DNP 3.0 Y Y —
EtherGate Y — —
GPS: Truetime/Datum1 Y — —
GPS: Arbiter1 Y — —
GPS: Arbiter-Vorne1 Y — —
Infrared I/O2 — Y —
1These protocol settings are used for connecting to a GPS receiver communicating in serial ASCII
format.
2This protocol setting is used to convert the optical port from communications to energy pulsing.
Related Topics
• Supported protocols
Communications setup
You can configure your meter’s basic communications parameters using the
display.
IP address setup
IP Address Contact your local network Sets the IP address for the meter
administrator for parameter NOTE: Your meter’s default IP address is
values 169.254.0.10
SubnetMask Use if subnetting applies to your network
Gateway Use in networks with multiple segments
MAC Address Not configurable Your meter’s media access control (MAC)
address.
50 7EN02-0374-00
Ethernet setup
Enable RSTP Yes, No Specifies if rapid spanning tree protocol (RSTP)

is enabled
NOTE: If local network loop or ring Ethernet
topologies are required, you must enable RSTP
for your meter’s Ethernet communications to
function
Enable ION Over Yes, No Specifies if ION protocol communications are
TCP enabled over Ethernet
Enable Web Yes, No Specifies if the meter’s webpages are enabled
Server for viewing
DNS setup
Primary DNS As defined by your Sets the address for the primary DNS server that
network’s system is configured to resolve domain names
administrator
Secondary DNS As defined by your Sets the address for the secondary DNS server
network’s system that is configured to resolve domain names
administrator
COM1 (RS-485) setup
Protocol ION, Modbus RTU, Modbus Sets the communications protocol for your
Master, DNP v3.00, meter’s RS-485 port
EtherGate,
GPS: Truetime/Datum,
GPS: Arbiter, GPS: Arbiter-
Vorne, Factory
Baud Rate 2400, 4800, 9600, 19200, Sets the data rate, in bits per second
38400, 57600, 115200
RTS Delay 0.000 to 1.000 Sets the transmit delay in seconds
Unit ID 1 to 9999 Sets the meter’s unique ID on the RS-485

network
NOTE: Modbus serial device range 0 to 247
Serial Port 8N1, 8N2, 8E1, 8E2, 8O1, Sets the parity and stop bits for the port
8O2
RS485 Bias Off, On Turns on biasing when mastering devices over
the RS-485 port
COM2 (optical port) setup

NOTE: The optical port is available on meters with an integrated display.
Protocol ION, Modbus RTU, DNP Sets the communications protocol for your
V3.00, Factory, Infrared I/O meter’s optical port
NOTE: Set the protocol to Infrared I/O to make
your meter’s optical port available for LED
energy pulsing then configure the LED energy
pulsing parameters.
Baud Rate 2400, 4800, 9600, 19200 Sets the data rate, in bits per second
RTS Delay 0 to 1 Sets the transmit delay in seconds
7EN02-0374-00 51
Unit ID 1 to 9999 Sets the meter’s unique ID on the meter’s optical

port
Serial Port 8N1, 8N2, 8E1, 8E2, 8O1, Sets the parity and stop bits for the port
8O2
COM3 (micro-USB port) setup

NOTE: The micro-USB port is available on meters with an integrated display.
Protocol ION, Factory Sets the communications protocol for your

meter’s optical port
Unit ID 1 to 9999 Sets the meter’s unique ID on the meter’s optical

port
NTP address
NTP Server As defined by your Specifies the IP address of the SNTP or NTP
network’s system server used by the meter for time
administrator synchronization
SMTP address
SMTP Server As defined by your Specifies the IP address of the SMTP server
network’s system used by the meter for sending email
administrator
RS-485 configuration
Before connecting your device to the RS-485 bus, use the meter’s display,
webpages or ION Setup to configure your meter’s default RS-485 settings.
Your meter has one RS-485 connection.
Your meter must have a unique unit identifier (address) and have the following
settings match the rest of the devices on the RS-485 bus:
• Protocol
• Baud rate
• Parity and stop bits
You can configure the following settings to help optimize communications
performance:
• RTS delay
• RS-485 bias
You can use a communications converter (USB to RS-485 or RS-232 to RS-485)
or an Ethernet gateway device to connect to your meter.
RS-485 Bias
You can use the RS-485 bias setting to fine tune communications.
Turn on the RS-485 bias when the meter is acting as a master over RS-485
communications and turn off the RS-485 bias when the meter is acting as a slave.
You can configure RS-485 biasing through the meter’s display or ION Setup.
52 7EN02-0374-00
RS-485 and gateway communications

Your meter can act as a gateway from the devices on the RS-485 bus to another
communications port on the meter.
For example, you can configure your meter as an Ethernet gateway, which lets you
communicate through the meter’s Ethernet port to the serial devices connected to
the meter’s RS-485 port using the ION protocol (EtherGate) or Modbus protocol
(Modbus gateway).
Related Topics
• Configuring an EtherGate gateway using ION Setup
• Configuring a Modbus gateway using ION Setup
Optical port overview

Your meter has an optical port on the integrated display.
Your meter’s optical port is designed to accept ANSI Type 2 magnetic couplers. It
provides serial communications for real-time measurements to a portable
computer, and can be used for meter configuration via the ION, Modbus RTU, DNP
3.0 or Factory protocols. It can also be configured for energy pulsing.
You can configure the optical port settings using the display or ION Setup.
Optical probe recommendations

You can use an optical probe to communicate to your meter through the optical
port located on the integrated display.
Terminal programs
If you are using a terminal program, it must allow you to control the DTR line to the
off state (-5V), for example, Tera Term 4.59 or later.
Using the Abacus Electrics A6Z-P-D09F optical probe

The A6Z-P-D09F derives all necessary power from the host computer serial port.
See the Abacus Electronics website for detailed information.
Ensure the 9-pin female “D” connector is connected to the appropriate COM port
on your laptop or handheld device.
This probe is compatible with ION Setup operating at its default settings, including:
• DTR: Disabled (or forced off)
• RTS: Toggle
Using the Abacus Electrics A9U-P-U04M optical probe (USB)

The A9U-P-U04M is a USB 1.1 and USB 2.0 compliant device that derives all
necessary power from the host computer and is for use with Windows 98/2000/XP
only. See the Abacus Electronics website for detailed information.
This probe comes supplied with “virtual serial port” drivers. Follow the
manufacturer’s instructions when installing virtual serial port driver software.
Ensure the USB connector is connected to the appropriate COM port on your
laptop or handheld device.
This probe is compatible with ION Setup operating at its default settings, including:
• DTR: Disabled (or forced off)
• RTS: Toggle
7EN02-0374-00 53
Configuring your meter’s optical port using the display

You can configure your meter’s optical port settings using the display.
1. Access your meter’s setup menu.

2. Navigate to Communications Setup.
3. Scroll to the COM2 Setup screen.
4. Configure the optical port’s serial communication settings as required.
Set the Protocol to InfraredI/O to set the optical port to energy pulsing instead
of serial communications.
Configuring your meter with ION Setup using the optical port
Connect an optical probe from a computer running ION Setup to the optical port on
the meter’s integrated display in order to configure your meter using ION Setup.
You need an optical probe to connect your computer to your meter. Your meter’s
optical port protocol must be set to ION.
1. Connect your optical probe to your computer and to the meter’s optical port.
2. Start ION Setup.
3. Select Single ION device configuration mode and click OK.
The Connection Type screen is displayed.
4. Select Serial.
5. Select the port connected to the meter from the Comm Port list.
Your computer’s physical USB ports end with COM, and you may have to try
different ports to select the port connected to your meter.
6. Click Settings and select the Timings tab.
7. Set RTS Control to Toggle.
8. Set DTR to Force Off.
9. Click OK.
10.In the Connection Type screen, click OK to connect to your meter.
ION Setup attempts to connect to your meter. When connected, the setup
assistant for your meter is displayed.
Configuring your meter’s optical port using ION Setup

You can configure the optical port on your meter’s integrated display for serial
communications or energy pulsing.
The optical port is only available on meters with an integrated display.
1. Start ION Setup.

3. Navigate to Communications > Serial Settings.
4. Select the tab corresponding to the optical port (Com2).
5. Highlight the parameters and click Edit to configure the optical port’s
parameters as required.
54 7EN02-0374-00
6. Click OK to set the parameter on the meter.
Optical port parameters available using ION Setup
Parameter Description
Protocol Sets the communications protocol for your meter’s

optical port.
NOTE: To configure your optical port for energy pulsing,
set the Protocol to Infrared I/O. Go to LED Pulsing >
Optical Port to set the optical port’s energy pulsing
parameters.
Unit ID Sets the meter’s unique ID on the meter’s optical port

Baud Rate Sets the data rate, in bits per second
RX Timeout Sets the timeout for receiving an entire message from a

device, in seconds
NOTE: This parameter only applies to ION and DNP
protocols; other protocols use a default setting that
cannot be configured
Serial Port Sets the parity and stop bits for the port
Configuring your meter with ION Setup over USB

Connect a USB cable from a computer running ION Setup to the mini-B USB on
the meter’s integrated display in order to configure your meter using ION Setup.
You need a USB to mini-B USB cable to connect your computer to the meter’s
mini-B USB port. The protocol of your meter’s mini-B USB port must be set to ION.
1. Connect your computer’s USB port to your meter’s mini-B USB port using the
cable.
2. Start ION Setup.
3. Select Single ION device configuration mode and click OK.
The Connection Type screen is displayed.
4. Select Serial. From the Comm Port list select the USB port connected to the
meter. Baud rate and parity settings are not used for USB communications and
do not need to be configured.
Your computer’s physical USB ports end with COM, and you may have to try
different ports to select the port connected to your meter.
5. Click OK.
ION Setup attempts to connect to your meter. When connected, the setup
assistant for your meter is displayed.
NOTE: You may need to load the driver for your computer to recognize the
meter as a USB device and connect using ION Setup. The USB driver is
located in the Drivers folder where the ION Setup program files are installed.
Refer to Microsoft help for instructions on loading USB drivers.
ION
ION is the native protocol and architecture of your meter.
The basic building blocks of ION architecture are the ION modules, each of which
is specialized to perform a specific task and contains data and instructions on how
to manage that data. ION modules are combined (linked) together to create the
meter’s functions and features. ION modules that are linked together to perform a
specialized task are called a framework, such as the Power Quality framework.
These different functional frameworks are then grouped together to define the
entire meter, and are collectively referred to as the device template.
7EN02-0374-00 55
Your meter ships with a default device template which provides extensive
capabilities. You can also configure your meter’s template to modify your meter’s
existing functions or to create new functions.
See the ION Reference, available from www.schneider-electric.com for further
information about ION architecture and a detailed description of the different ION
modules. See the ION Device Template Reference, available from
www.schneider-electric.com, for details on the modules and their configuration in
your meter’s default template.
Modbus
Modbus is a master/slave communications protocol where the master initiates
transactions and the slave(s) responds with the requested information or action.
Your device can function as a Modbus slave or Modbus master, depending on how
it is configured. Your device comes with Modbus slave functionality configured and
ready to use. You can add custom Modbus information to the default Modbus slave
data provided by your device.
Key terms
Term Definition
Modbus gateway A communications method that lets you communicate through an
Ethernet gateway device to a Modbus serial network connected to
that device.
Modbus master A device that issues commands and receives responses from
Modbus slave devices. Serial Modbus networks can only have one
Modbus master per network.
Modbus RTU Serial Modbus protocol format; Modbus RTU transmits data using
binary. Master and slave devices must use the same format.
Modbus register/address Identifies the data to read/write. Modbus register maps are available
for Modbus slave devices and detail the information available from
the slave device. More than one register may be used to store a
single value.
Modbus slave A device that responds to Modbus commands and performs actions
or provides information back to the Modbus master. Most Modbus
networks contain multiple slave devices.
Modbus TCP The Ethernet Modbus protocol format.
Modbus unit ID The identifier for a slave Modbus device.
You can download your device’s Modbus map from www.schneider-electric.com

and get additional information about the Modbus protocol from www.modbus.org.
Your meter as a Modbus slave on a serial network

Your meter can function as a Modbus slave on a serial network.
A Modbus master
B RS-485 Modbus RTU
C Modbus slaves
D Your meter
56 7EN02-0374-00
Your meter as a Modbus slave over Ethernet

Your meter can function as a Modbus slave over Ethernet.
A Modbus master
B Ethernet Modbus TCP
C Your meter
Your meter as a Modbus master with serial Modbus slave devices

Your meter can function as a Modbus master with serial Modbus slave devices.
A Ethernet
B Your meter
C RS-485 Modbus RTU
D Modbus slaves
Your meter as a Modbus master with Ethernet Modbus slave devices

Your meter can function as a Modbus master with Ethernet Modbus slave devices.
A Ethernet
B Your meter
C Modbus slaves
Supported Modbus features

Your meter supports specific Modbus data classes, data formats, function codes
and commands.
Modbus data classes

Class Description
Coils Digital bits that can be read and written to
Input status Digital bits that can be read
Input registers 16-bit integers that can be read
Holding registers 16-bit integers that can be read and written to
7EN02-0374-00 57
Modbus data formats

Format Type # of Modbus registers used
Unsigned 16-bit Integer 1
Signed 16-bit Integer 1
Unsigned 32-bit Integer 2
Signed 32-bit Integer 2
Unsigned 32B-M10K Integer 2
Signed 32B-M10K Integer 2
IEEE float1 Floating point 2
Packed Boolean for inputs Integer 1
Packed Boolean for coils Integer 1
Unsigned 16-bit read/write Integer 1
Signed 64 bit Integer 4

1 Meters acting as Modbus masters support two versions of IEEE float with different word orders:
high/low = Big Endian, low/high = Little Endian.
16-bit data (one word) is transmitted with most-significant byte first and least-
significant byte second.
32-bit data (two words) is transmitted with the most-significant word first and the
least-significant word second.
Modbus function codes

Function Description Master/slave
1 Read coil status Master and slave

2 Read input status Master and slave
3 Read holding registers Master and slave
4 Read input registers Master
5 Write to a coil Master

6 Write to a holding register Master and slave
15 Write to multiple coils Master
16 Write to multiple holding registers Master and slave
17 Report slave ID (serial only) Master and slave
43 (subcode 14) Read device identification Master and slave
100 Read scattered holding registers Master and slave
Modbus commands
A Modbus master command to unit ID 0 is broadcast (sent to) all Modbus slave
devices. The only supported broadcast command is preset multiple registers.
For serial Modbus networks with only one slave device, the master can send
commands using the single connection, one-to-one address of unit ID 248,
regardless of the slave device’s actual unit ID.
Modbus implementation
Your meter's Modbus implementation includes exception codes, invalid register
responses, fixed and configurable register maps, and security.
58 7EN02-0374-00
Modbus exception codes
Code Name Description
01 Illegal function The requested command is invalid.
02 Illegal address This code indicates one of the following:

• The requested address is invalid for that function.
• The requested address is not within the valid register
range for this device.
• The requested address is protected by device security.
03 Illegal value This code indicates one of the following:

• The requested value is not allowed for that register in
the device.
• The requested register is part of a multi-word value.
Modbus invalid read registers responses
Invalid type Read response
Unmapped (unused)1 register 0x8000
Reserved1 register responses by type
Signed integer 16-bit 0x8000
Unsigned integer 16-bit 0xFFFF
Signed integer 32-bits 0x80000000
Unsigned integer 32-bits 0xFFFFFFFF
Signed integer 64-bits 0x8000000000000000
Float32 0xFFC00000
(NaN = Not a number)
1 IRIG-B can only be connected to one of the digital inputs located on the meter base, not an option
module. Unmapped (unused) registers are registers that will never be used by the meter, and
therefore have no defined format. Reserved registers have a defined format and are intended for use
by the meter, its options or its variants.
Modbus invalid write registers response

If the meter receives a write command to a Modbus register address that does not
have a register mapped, the meter does not respond. No data is written or stored,
and the meter does not send back a rejection to the request.
If the meter receives a write command to a read-only Modbus register address,
exception code 3 (illegal value) is returned.
Fixed and configurable Modbus map

Your device has a fixed (static) register map for meter data and a flexible, user-
configured register map.
Modbus security
Your meter’s onboard security options include Modbus-specific settings. These
security settings may need to be configured in order to write Modbus data to the
meter.
Modbus best practices for serial

In order for your meter to operate as a serial Modbus device, you must complete
some prerequisite configuration.
7EN02-0374-00 59
Prerequisite Description
Wiring The device’s serial connection must be wired correctly.

The Modbus slave devices must have communications wiring to the Modbus
master.
Protocol Slave: for your meter to be a serial Modbus slave, the meter’s protocol must be
set to Modbus RTU. Master and slave devices must use the same format.
Master: for your meter to be a serial Modbus master, the meter’s protocol must
be set to Modbus Master.
Baud rate The baud rate must be the same for all devices on the serial Modbus network.
Stop bits and The communication stop bits and parity (for example, 8N1) must be the same
parity for all devices on the serial Modbus network.
Unit ID Each device on the serial Modbus network must have a unique unit ID (also
called the device address).
Modbus best practices for Ethernet

In order for your meter to operate as an Ethernet Modbus device, you must
complete some prerequisite configuration.
NOTE: You do not need to perform any Modbus-specific configuration for your
meter to function as a Modbus slave device over Ethernet.
Ethernet All devices must have a working Ethernet connection.
IP address All devices must have a unique IP address.
Port All devices must be communicating over Ethernet port 502 for Modbus TCP.
NOTE: Devices supporting multiple simultaneous Modbus TCP connections can

have communications delays. Adjust your network timeout settings to
accommodate this.
Modbus master best practices

In order for your meter to operate as a Modbus master, you must complete some
prerequisite configuration.
NOTE: These settings are required in addition to the serial or Ethernet Modbus
prerequisites.
Modbus slave All Modbus slave devices must be communicating and appropriately configured.
devices
Protocol • Modbus mastering serial devices: the master’s serial port protocol must be
set to Modbus master.
• Modbus mastering Ethernet devices: the master must be communicating to
the slave devices over Ethernet port 502.
NOTE: Having more than one Modbus master on a serial Modbus network may
cause communication conflicts.
Mastered devices The Modbus master device must have the slave device information entered for
mastering.
Modbus map
Your meter’s default Modbus register information (map) is available for download
from www.schneider-electric.com.
The Modbus register information includes:
• registers and mapped values
• formats and scaling
60 7EN02-0374-00
• additional details where applicable

NOTE: Your meter’s Modbus registers are specified differently than previous
devices using ION architecture. If you are configuring Modbus slave information on
your meter, confirm you are using the appropriate Modbus register addressing.
Refer to your meter’s Modbus map for more information.
Your meter has a fixed (static) register map which contains the most common
metering values. This map is defined by a series of Data Mapping modules, which
also determine the values shown on your device’s display and webpages. The
Data Mapping modules are named based on the type of information they map to
Modbus:
Data Mapping module Description
Data Mapping Dmd Modules Maps kW, kVA and kVAR demand data such as
kW sd del (sliding demand kilowatts delivered)
as well as current demand such as I a sd (sliding
demand phase A current).
Data Mapping Egy Modules Maps kWh, kVAh and kVARh delivered and
received data, including conditional, quadrant
and incremental energies.
Data Mapping EN Modules Maps present interval EN50160 power quality

compliance data.
Data Mapping EN Prev Modules Maps previous interval EN50160 power quality
compliance data.
Data Mapping I/O Modules Maps input metering data, alarms, resets and
reset counts.
Data Mapping Meas Modules Maps measured data from the standard and
high-speed Power Meter module.
The Cfg Modbus Map Enable setup register may
exist in this module.
Data Mapping PQ Modules Maps power quality data such as Crest Factor, K
Factor and total harmonic distortion, including
IEC 61000-4-30 power quality compliance data.
Data Mapping Stats Modules Maps statistical low, mean and high data values,
such as I a mean (phase A current average
value).
Data Mapping TOU Modules Maps time-of-use (TOU) data, such as seasons,
rates, and per-season demand such as kW sd
rec A (sliding demand kilowatts received in
season A).
You can add extra Modbus information or duplicate information that is already in
the fixed map to different Modbus registers using Modbus Slave modules.
See the ION Reference available from www.schneider-electric.com for detailed
information about Data Mapping modules and Modbus Slave modules.
Related Topics
• Configuring custom Modbus data using ION Setup
Configuring your meter for Modbus using the display

You can use the display to configure your meter as a Modbus slave or partially
configure your meter for Modbus mastering.
NOTE: Your meter’s communications must be wired and configured before you
begin this procedure.
Your meter does not require any Modbus-specific configuration to act as a Modbus
slave device over Ethernet.
1. Navigate to Setup Menu > Communications Setup and select the serial
communications setup screen.
7EN02-0374-00 61
2. Configure the serial port’s Modbus parameters as required.
Parameter Setting
Protocol Modbus RTU or Modbus master

• Off if the meter is a Modbus slave
RS485 Bias
• On if the meter is a Modbus master
3. Configure the meter’s other serial port parameters as required.

For Modbus master, you must add the Modbus slave devices using ION Setup.
Related Topics
• Meter setup using your meter’s display
Configuring your meter as a Modbus slave using ION Setup

You can configure your meter as a Modbus slave using ION Setup.
Your meter’s serial connection must be wired and configured correctly. The same
mode of serial communication must be used for all devices on the network.
Your meter does not require any Modbus-specific configuration to act as a Modbus
slave device over Ethernet.
1. Start ION Setup.

3. Navigate to Communications > Serial settings. Select the tab for the serial
port you want to configure.
4. Highlight the parameter and click Edit to configure the serial port’s Modbus
Parameter Setting
Protocol Modbus RTU or Modbus master

RS485 bias • Off if the meter is a Modbus slave
• On if the meter is a Modubs master
5. Configure the meter’s other serial port parameters as required.
See your device’s Modbus map, available from www.schneider-electric.com for

Modbus register information.
Configuring custom Modbus data using ION Setup

You can add custom data to your meter's default Modbus map, completely
customize your meter's Modbus map, or revert your meter's Modbus map back to
its default configuration using ION Setup.
You can download your meter’s Modbus map information from
1. Start ION Setup.

3. Navigate to Communications > 3rd party protocols and click on the Modbus
Slave tab.
The name of the meter’s current Modbus map is displayed, along with the
quantity of custom registers and their start and end addresses.
4. Select the map name and click Edit.
The Modbus Slave Mode Setup screen is displayed.
62 7EN02-0374-00
5. Select your meter’s method of Modbus slave mapping. If you select Default or
Disabled, click Finish to configure your meter and return to the Setup
Assistant, otherwise select Next to access the Modbus Slave Map Setup
screen.
Option Description
Default Sets your meter to use the default Modbus map. Any custom Modbus
slave data is removed.
NOTE: You can download your meter’s Modbus map information from
Modified Add Modbus information in addition to the meter’s default Modbus map.
Custom Removes the meter’s default Modbus map so that all registers are
available so you can create a completely custom Modbus map.
NOTE: Use this option if you want to make your meter’s Modbus map
identical to a device that it is replacing, for example in a retrofit
application.
Disabled Removes your meter’s Modbus data map. Modbus functions are
unaffected but no meter Modbus data is available.
6. In the Modbus Slave Map Setup screen, you can modify parameters by
clicking Edit, or add parameters by clicking Add.
The Modbus Register screen is displayed.
7. Configure the Modbus register information and click OK to return to the
Modbus Slave Map Setup screen.
a. Source: click Select and chose a source from the Parameter Selection
screen. Select Show all available registers to see a complete list of the
parameters available on your meter. Click OK.
b. Address: enter the Modbus address that will hold the Source data.
NOTE: If you hover your mouse over the Address field, a tooltip indicates
the Modbus function code and start address to send for retrieving the data.
c. Format: select the Modbus data format from the list.
d. Scaling: select the scaling value from the list, or select Custom and click
Scales to configure custom scaling.
8. In the Modbus Slave Map Setup screen you can click Delete to remove a
Modbus register, Set Name to create a new name for the set of additional data
mapped to Modbus, or Save As to save the additional data you have mapped
to Modbus as a separate file.
9. Click Finish to complete your meter’s Modbus slave configuration and return to
the Setup Assistant.
Configuring your meter as a Modbus master using ION Setup

You can configure your device to Modbus master slave devices over serial or
Ethernet.
Make sure your master and slave devices have the prerequisite communications
wiring and configuration before configuring your meter as a Modbus master.
NOTE: Devices supporting multiple simultaneous Modbus TCP connections can
have communications delays. Adjust your network timeout settings to
accommodate this.
The meter as a Modbus master over TCP/IP attempts to communicate with a slave
device for up to 100 seconds (as per the RFC1122 standard) before moving on to
the next slave device.
1. Start ION Setup.

3. Navigate to Communications > 3rd Party Protocols and click on the Modbus
Master tab.
7EN02-0374-00 63
4. Click Add to add a Modbus slave device.

The Modbus Device dialog appears.
5. Enter the Modbus slave information:
– Enter the Modbus slave device’s name and a label suffix (if applicable).
– Select the device type of the slave device from Device Type.
– Enter the unit ID of the Modbus slave device into Slave ID.
– Select the serial or TCP connection from Connected via. This is the
connection from the Modbus master to the slave device.
6. Click Connections. The Modbus Master Connections dialog appears.
7. Select the tab that corresponds to the connection you are configuring (for
example, if you selected TCP Connection 1 from Connected via, select the
TCP 1 tab) and configure it based on the connection type.
Connection type Configuration
Serial connection Select the serial communications port that is connected to the Modbus
slave devices from the Assigned Port list.
TCP connection Enter the IP address of the Modbus slave device, making sure that the
IP port is set to 502.
8. Click OK to return to the Modbus Device dialog.

9. Click OK to add the slave device. The device now appears on the list. Repeat
these steps to add all of your Modbus slave devices.
Related Topics
• Modbus
Ethernet gateway
Ethernet gateway is a communications method that allows you to communicate
through a gateway device to a serial network.
When a meter with gateway capabilities is installed on an Ethernet network, a
master device (such as an energy management system) can communicate through
the gateway meter to a serial network of devices connected to the gateway meter’s
serial port(s). The maximum number of devices on the serial network is determined
by the limitations of the gateway meter’s serial port.
There are two types of Ethernet gateways that you can configure on your meter:
• EtherGate: a single TCP connection communicates through the gateway meter
to a serial network of devices.
• Modbus gateway: up to a maximum of 32 Modbus master TCP connections
communicate through the gateway meter to a serial network of Modbus
devices.
Related Topics
• Specifications
EtherGate
The meter can function as an Ethernet gateway (EtherGate).
EtherGate is a protocol-agnostic communications method that lets you
communicate through a gateway meter to a serial network of devices letting ION or
other RTU over TCP data pass through the gateway meter to other networks,
including third party systems. When a meter installed on the Ethernet network has
EtherGate enabled, a master device (such as an energy management system) can
communicate through the gateway meter to a serial network of devices wired to the
gateway meter’s COM port. You must create an additional communications
connection to the gateway meter in order to read its information.
64 7EN02-0374-00
A D
B
A Gateway meter
B Ethernet (single TCP connection)
C Serial network of devices

D Master device (one only)
For EtherGate, you must install the serial devices, configure them and connect
them to your Ethernet-connected gateway meter. Ensure that each serial device is
configured with the same protocol and baud rate and has a unique unit ID.
Configure the gateway meter’s serial port to use the EtherGate protocol, create the
EtherGate site in ION Setup or an energy management system, and add the serial
devices to the EtherGate site.
NOTE: EtherGate supports only one master device.
Related Topics
• Configuring an EtherGate gateway using ION Setup
Modbus Ethernet gateway

The meter’s Ethernet gateway feature extends the meter’s functionality by allowing
Ethernet access to serial devices connected to the meter’s RS-485 serial
communications port.
A Gateway meter
B Ethernet (multiple Modbus master TCP

connections)
C Downstream serial Modbus slave

devices
D Multiple Modbus master devices
A Modbus master device (such as an energy management system) can

communicate through the gateway meter to a serial network of devices connected
to the gateway meter’s serial port(s). The meter receives Modbus TCP/IP data on
TCP port 502, translates it to Modbus RTU then forwards it to the addressed slave
device.
This functionality allows the use of monitoring software to access information from
slave devices for data collection, trending, alarm/event management, analysis, and
other functions.
Configuring EtherGate using the display

Use the meter’s display to configure a serial port to use the EtherGate protocol.
1. Navigate to Setup Menu > Communications Setup and go to the serial

communications setup screen.
2. Set the serial port’s protocol to EtherGate. Configure the other serial port
7EN02-0374-00 65
Configuring a Modbus gateway using ION Setup

You can configure Modbus gateway on your meter using ION Setup.
Before you begin, make sure you have completed the following tasks:
• Confirm the serial network of devices are wired and configured to have the
same baud rate, serial port settings (for example, 8N1), and protocol (Modbus).
• Confirm each serial device has a unique unit identifier.
• Confirm the serial network of devices are connected to the gateway meter’s
serial communication port.
• Confirm your gateway meter is communicating over Ethernet.
1. Start ION Setup.

3. Navigate to Communications > Serial settings and select the tab for the
communications port that the serial network is connected to.
4. Select Protocol and click Edit.
The protocol selection screen appears.
5. Set the protocol to Modbus Master.
6. Navigate to Communications > Network settings and select the TCP/IP tab.
7. Select Modbus Gateway and click Edit.
The Modbus gateway selection screen is displayed.
8. Select the communications port that the serial network is connected to (and you
just set to use the Modbus master protocol) and click OK. The Modbus gateway
connection is created.
9. Create an Ethernet gateway site to access the serial network of devices
through your gateway meter.
Configuring an EtherGate gateway using ION Setup

You can configure EtherGate on your meter using ION Setup.
Before you begin, make sure you have completed the following tasks:
• Confirm the serial network of devices are wired and configured to have the
same baud rate, serial port settings (for example, 8N1), and protocol (ION).
• Confirm each serial device has a unique unit identifier.
• Confirm the serial network of devices are connected to the gateway meter’s
serial communication port.
• Confirm your gateway meter is communicating over Ethernet.
1. Start ION Setup.

3. Navigate to Communications > Serial settings and select the tab for the
communications port that the serial network is connected to.
4. Select Protocol and click Edit. The protocol selection screen appears.
5. Set the protocol to EtherGate.
6. Create an Ethernet gateway site to access the serial network of devices
through your gateway meter.
Creating an Ethernet gateway site using ION Setup

You can create an EtherGate or Modbus gateway site in ION Setup to view serial
devices connected to your meter when it is functioning as an Ethernet gateway.
You must have Ethernet gateway communications configured and your gateway
and serial devices connected and communicating.
66 7EN02-0374-00
1. Start ION Setup.

2. Right-click on your workstation icon and select Insert Item.
The New Network Item dialog appears.
3. Select Site and click OK.
The New Site dialog appears.
4. Select the General tab and configure the site.
Parameter Values/Options Description
Name - Ethernet gateway site name
Comm Link Ethernet Ethernet communications

Ethernet options Gateway Ethernet gateway
communications
Gateway Info: IP Addr — IP address of the Ethernet
gateway meter
Gateway Info: Port 7801, 502 • 7801 for EtherGate

• 502 for Modbus gateway
5. Click OK to create the site.

6. Right-click on your newly created site and select Insert Item.
The New Network Item dialog appears.
7. Make sure your newly created Ethernet gateway site is selected in Attach to.
8. Select Device and click OK.
The New Device dialog appears.
9. Enter the details of your serial device. Click OK to add the serial device to your
Ethernet gateway site.
10.Repeat for all the serial devices on the gateway meter.
NOTE: Use a separate standard Ethernet connection in ION Setup to connect
to and read data from your Ethernet gateway meter.
FTP
Your meter has an internal FTP server that you can use to load files, such as
custom webpages, and upgrade your meter and meter accessories.
File transfer protocol (FTP) is a standard, client-server network protocol used to
transfer files over TCP (Ethernet) networks.
FTP memory allocation

Your meter’s FTP memory usage changes when you copy a file to the meter’s
internal FTP site or modify a feature that uses the meter’s FTP site.
If you attempt to load a file onto your meter’s FTP site that is too large, your FTP
program displays an error, and you must delete files from your meter’s internal FTP
site to free up memory before loading the file.
If you modify a meter feature which uses FTP memory, such as increasing the
number of COMTRADE waveform records, the meter checks to confirm sufficient
space is available on its internal FTP site before enabling the modified feature. If
there is insufficient space, the feature is disabled, and you must delete files from
your meter’s FTP site to increase the available space before enabling the feature.
FTP file structure and permissions

Your meter has an FTP folder structure.
• COMTRADE: you can read COMTRADE files from these folders, but you
cannot delete or add files to these folders.
7EN02-0374-00 67
• IEC61850: you can add an IEC 61850 configuration (CID) file to this folder to
activate the IEC 61850 protocol functions of your meter.
• optionModuleUpg and rmdUpg: you can load firmware update files for your
meter’s remote display or option modules into these folders.
• documents: this folder is intended for user storage. You can read, write and
delete any type of files in this folder.
• web: this folder is where the meter’s default webpages are stored and where
you can add custom webpages to the meter by copying them into the
appropriate subfolders.
FTP filename requirements

FTP filenames are limited to standard ASCII characters.
This means that they cannot contain a blank space, quotation marks or \, /, *, ?, <
or >, and are limited to 68 characters in length, including the file extension. The “/”
character is only used as part of the FTP file directory information.
Accessing your meter’s FTP server

You must have FTP software such as Filezilla, WinSCP or Windows Explorer
running on a Windows-based machine to transfer files to and from your meter’s
internal FTP server.
1. Start your FTP software.

2. Connect to your meter via FTP by entering your meter’s IP address. Depending
on your FTP software and meter security settings, you may be prompted for
login credentials.
NOTE: With standard meter security (no user configured), enter login
credentials of 8000 and the meter password to connect to the meter. For
advanced meter security, enter a valid user and password.
3. Navigate to the appropriate folder on your meter.
4. Close your FTP software to disconnect from the meter. The FTP connection
automatically disconnects once the FTP timeout period has elapsed.
SNMP
Simple Network Management Protocol (SNMP)
Your meter supports SNMP once you have enabled SNMP on your meter. You
need to upload the meter’s MIB file (available from www.schneider-electric.com)
into the NMS managing your meter.
Simple Network Management Protocol (SNMP) is part of the Transmission Control
Protocol/Internet Protocol (TCP/IP) protocol suite. SNMP is an application layer
protocol that enables the exchange of network management information between
devices, allowing you to manage network performance and to identify and solve
problems on networks with devices of various types.
SNMP configuration assumes that you have an advanced understanding of SNMP
and the communications network and power system that your meter is connected
to.
Key terms
Term Definition
Agent Software resident on the managed device which interfaces between the
device and the NMS.
Managed device Your meter in the SNMP network.
68 7EN02-0374-00
Term Definition
Community name/ A text string that helps authenticate requests between the managed device
string and the NMS.
Managed object Any parameter referenced in the MIB file.
MIB A management information base which organizes the OIDs in a

hierarchical tree.
NMS A network management station, manager or client that executes
applications to monitor and control devices. An NMS must have the
standard and custom MIB files and SNMP manager software.
OID An object identifier that uniquely identifies and labels a managed object in
the MIB.
Trap receiver An NMS that is configured to receive traps and whose IP address is an
SNMP trap destination.
The meter in an SNMP system

Your meter is a managed device with an SNMP agent in an SNMP network.
A Trap receiver(s)
B SNMP agent (meter)
C NMS with SNMP manager software and the PM556x MIB file installed
NOTE: The NMS computer can also function as a trap receiver.
SNMP implementation
MIB files
Your meter is compliant with MIB-II as defined by the standard MIB file RFC 1213.
SNMP requires that you load your meter’s ION MIB file (available for download
from www.schneider-electric.com) into the NMS.
You must install RFC 1213, which is required to read basic network information for
the meter (for example, TCP/IP traffic or number of packets received), if it is not
included with your SNMP manager software.
Community strings
A community string is a text string which acts to help authenticate requests from
the NMS to your meter.
There are two community strings on your meter:
• Read Only Community: this community string is used by SNMP get (read-only)
requests. The read only community string’s initial factory-set value is public.
7EN02-0374-00 69
• Read Write Community: this community string is used by SNMP set (read/write)
requests. The read write community string’s initial factory-set value is private.
NOTE: You can also use the read write community string for SNMP get (read-only)
requests.
If your meter receives an incorrect community string, it generates an
AuthenticationFailure trap.
System strings
A system string is a text string which can be configured to provide information
about your meter.
There are three system strings on your meter:
• System contact: enter the name of the SNMP system administrator.
• System name: enter a descriptive name for your meter.
• System location: enter a description of your meter’s location.
SNMP trapping
SNMP trapping allows your meter’s agent to notify the NMS of events with an
unsolicited SNMP message (a “trap” of the meter’s alarm event).
You can enter up to four IP addresses for SNMP trap notification for generic and
enterprise-specific traps. For enterprise traps, you must also define the number of
events or maximum time delay before SNMP traps are sent to the NMS.
SNMP trapping is only supported on SNMP v2.
SNMP trapping implementation

Generic SNMP traps supported by your meter are:
• Coldstart: the meter (SNMP agent) is starting.
• Linkup: the SNMP agent is enabled.
• AuthenticationFailure: the meter (SNMP agent) has received an incorrect
community value.
Enterprise-specific SNMP traps supported by your meter are:
• Low: trap of events with a low event priority.
• Medium: trap of events with a medium event priority.
• High: trap of events with a high event priority.
Trap Event priority range
Low 64–127
Medium 128–191
High 192–255
NOTE: The number of events or maximum time delay settings only apply to
enterprise SNMP traps.
See the ION Reference, available from www.schneider-electric.com, for detailed
information on the SNMP Mapping, SNMP Options and Alarm Options modules.
70 7EN02-0374-00
Related Topics
• Configuring SNMP using ION Setup
• Configuring SNMP using your meter’s webpages
Default SNMP mapping

Enabling SNMP provides SNMP access to the meter values linked to the SNMP
Mapping module.
You can configure the SNMP Mapping module to link to different meter values. By
default, the following meter values are linked to the SNMP Mapping module:
Ia kVAR tot Vll ca Vln avg Ib mean kW sd mx del-

rec
Ib kVA tot Vll avg Freq Ic mx kW sd del
Ic PF sign tot Vln a Ia mx Ic mean kW sd rec
I avg Vll ab Vln b Ia mean kW sd mx del kW sd del-rec
kW tot Vll bc Vln c Ib mx kW sd mx rec kVAR sd mx

del
kVAR sd mx kVAR sd mx kVAR sd del kVAR sd rec kVAR sd del- kVA sd mx del
rec del-rec rec
kVA sd mx rec kVA sd mx kVA sd del kVA sd rec kVA sd del- kWh del
del-rec rec
kWh rec kWh del-rec kVARh del kVARh rec kVARh del- kVAh del
rec
kVAh rec kVAh del-rec
The following meter information is always provided by default and cannot be

configured:
Voltsmode Model number

Serial number Device name
Firmware version MIB version
If you change your meter’s default values you must modify the custom MIB file to
reflect the new values.
Changing your meter’s default SNMP configuration assumes that you have an
advanced understanding of ION architecture, SNMP, and the communications
network and power system that your meter is connected to.
information on the SNMP Mapping module.
Configuring your SNMP MIB file

You must configure your MIB file if you have modified the default SNMP
information provided by the meter in order for the MIB file labels to reflect the
modified values.
Download the ION MIB file from www.schneider-electric.com.
NOTE: You should only configure the variable name and description. Changing
other fields in your MIB file may cause the client software to report problems or
return errors when trying to retrieve or view parameters.
The variable name must conform to the following rules:
• The first character must be a letter.
• The first character must be lower case.
• The name must not contain any special characters such as *, ?, &.
• The name must not contain spaces.
7EN02-0374-00 71
1. Open your meter’s MIB file in a text editing program (such as Notepad).
2. Update the variable name and description so they match the meter values
connected to the SNMP Mapping module.
3. Save your meter’s MIB file. Make sure you keep the original file extension of .
MIB.
This example shows an original and an updated OID entry in an MIB file, where the
default meter value of voltage line-to-neutral phase A is modified in the meter’s
SNMP Mapping module and is now connected to voltage line-toneutral phase C.
Original OID entry
Vln_a OBJECT-TYPE
SYNTAX DisplayString (SIZE (0. . 255))
ACCESS read-only
STATUS mandatory
DESCRIPTION “Host Meter Voltage Line A to Neutral Units = V (Volts)” ::= { Schneider Electric 34 }
You must update the variable name and description to match the meter values
connected to the SNMP Mapping module:
Value Original Updated
Variable name Vin_a Vin_c
Description “Host Meter Voltage Line A to Host Meter Voltage Line C to

Neutral Units = V (Volts)” ::= { Neutral Units = V (Volts)” ::= {
Schneider Electric 34 } Schneider Electric 34 }
The SNMP client software reads the original and updated file as follows:
Original Updated
variable name: Vln_a variable name: Vln_c

Description: “SNM1 Input 1 - Voltage (line- Description: “SNM1 Input 1 - Voltage (line-to-
toneutral) phase A” neutral) phase C”
Configuring SNMP using ION Setup

You can enable SNMP and configure SNMP trapping using ION Setup.
You must download the ION MIB file from www.schneider-electric.com
1. Start ION Setup.

3. Navigate to Communications > Network Settingsand select the SNMP tab.
72 7EN02-0374-00
4. Configure your meter’s SNMP parameters by selecting the parameter and

clicking Edit. Click OK in the editing screen to set the parameter value.
Enable SNMP Enables or disables SNMP on your meter.
Enable Traps Enables or disables SNMP trapping on your meter.
Trap Rcvr Addr1 — Enter up to four trap receiver IP addresses where trap messages will be
Trap Recvr Add4 sent.
Read only community Enter the community string used for SNMP get (read-only) requests.
Read write Enter the community string used for SNMP set (read/write) requests.
community
NOTE: You can use the read/write community string for SNMP get
(read-only) requests.
System contact Enter the name of your SNMP system administrator.
System name Enter a descriptive name for your meter.
System location Enter your meter’s location.
5. Review the rest of the SNMP information and modify if necessary.
Related Topics
• Simple Network Management Protocol (SNMP)
Configuring SNMP using your meter’s webpages

You can configure SNMP trapping using your meter’s webpages.
You must download the ION MIB file from www.schneider-electric.com.
1. Connect to your meter’s webpages.

2. Go to Setup > SNMP Parameters.
7EN02-0374-00 73
3. Configure your meter’s SNMP parameters by selecting the parameter value.
Parameter Range Description
Enable SNMP . Yes/no Enables or disables SNMP on your meter.
SNMP Port Number 161 (default) Enter your meter’s SNMP port number
System contact — Enter the name of your SNMP system administrator.
System name — Enter a descriptive name for your meter.
System location — Enter your meter’s location.
Read-only Community Name — Enter the community string used for SNMP get (read-only) requests.
Read-write Community Name — Enter the community string used for SNMP set (read/write) requests.
NOTE: You can use the read/write community string for SNMP get (read-
only) requests.
Enable SNMP Traps Enable/disable Enables or disables SNMP trapping on your meter.
Enable High Priority Alarms Yes/no Enables trapping of events that create high priority alarms.
Enable Med Priority Alarms Yes/no Enables trapping of events that create medium priority alarms.
Enable Low Priority Alarms Yes/no Enables trapping of events that create low priority alarms.
Report Buffer Size 1 - 30 Enter the maximum number of trap messages to be stored before the trap
messages are sent. Traps are sent when the number of trap messages is
equal to or greater than this value.
Report Hold Time 1 - 300 seconds Enter the maximum duration for trap messages to be held. Trap messages
are sent when the time after a trap event has occurred is equal to or
greater than this value.
Trap Rcvr1 Addr - — Enter up to four trap receiver IP addresses, where trap messages will be
Trap Rcvr4 Addr sent.
4. Click Apply to configure the meter’s SNMP parameters.
IEC 61850
IEC 68150 is an Ethernet-based protocol designed for electrical substations.
It is a standardized method of communications, developed to support integrated
systems composed of multi-vendor, self-describing IEDs (intelligent electronic
devices) that are networked together.
Your meter can be integrated into an IEC 61850 system as an IED (or server)
supporting concurrent IEC 61850 client connections and an FTP connection (used
for transferring data or configuration files).
You can go to the IEC (International Electrotechnical Commission) website at www.
iec.ch for information about the IEC 61850 protocol. For more information on how
IEC 61850 is implemented on your meter, see the IEC 61850 and ION Technology
protocol document.
IEC 61850 implementation

Your meter comes configured with a default set of meter data available to IEC
61850.
This default set of meter data is used in the default data sets and reports in the ICD
file(s) available for download from www.schneider-electric.com.
NOTE: Select the ICD file that matches your meter’s option module configuration.
You must load a valid IEC 61850 configuration (CID) file into the meter’s internal
FTP site in order to activate the IEC 61850 features of your meter.
NOTE: Your meter can have only one IEC 61850 configuration (CID) file loaded
onto its internal FTP storage. If additional CID files are loaded, IEC 61850
functions are deactivated until the additional files are removed.
74 7EN02-0374-00
You can load the IEC 61850 configuration file and configure the IEC 61850 custom
modules using ION Setup.
Related Topics
• FTP
• Specifications
Loading an IEC 61850 configuration file using ION Setup

You can load an IEC 61850 configuration (CID) file using ION Setup over an
Ethernet connection.
You must have:
• The IEC 68150 configuration file stored in a location accessible by ION Setup.
The configuration file is created by customizing the IEC 61850 device (ICD) file,
which can be downloaded from www.schneider-electric.com.
• FTP access to your meter from the computer running ION Setup.
NOTE: Your meter can have only one IEC 61850 configuration (CID) file loaded
onto its internal FTP site. If additional CID files are loaded, IEC 61850 functions are
deactivated until the additional files are removed.
1. Start ION Setup.

3. Navigate to Communications > 3rd Party Protocols and select the IEC
61850 tab.
4. Highlight a parameter and click Upload. Navigate to where you stored your
meter’s CID file, select the file, and click Open.
Your meter reviews the CID file to determine if it is valid. This process may take
several minutes.
The CID status indicates whether the meter has received and validated an IEC
61850 CID file and is operating as an IEC 61850 server.
Configuring additional data for IEC 61850 using ION Setup

You can map additional data to IEC 61850 using ION Setup.
You must have a valid IEC 61850 configuration file loaded onto your meter for IEC
61850 functionality, but it is not necessary for configuring additional data.
NOTE: You can configure additional data at any time, whether or not IEC 61850 is
operating on your meter.
1. Start ION Setup.

3. Navigate to Communications > 3rd Party Protocols and select the IEC
61850 tab.
4. Select the information type that corresponds to the type of meter information
that you want to add to your IEC 61850 data. Select analog for numeric
information and digital for boolean or binary information. Click Edit. The custom
configuration screen is displayed.
5. Select the desired meter value from those available. If the value you want is not
shown, select Show all available registers.
6. Select an IEC 61850 leaf to associate with the meter data, and click >> to map
the value. Click << to unmap values. Click OK to send and save your changes
to the meter.
7EN02-0374-00 75
Configuring digital outputs for IEC 61850 control using ION Setup
You can configure your digital outputs so that they can be used for non-critical
control via IEC 61850.
Your meter has a comprehensive default implementation of IEC 61850 which
meets the needs of most systems with only basic configuration. You can customize
this implementation so that IEC 61850 can be used to control your meter’s digital
outputs; this is an advanced procedure that requires in-depth knowledge of your
meter, its underlying architecture, and the system in which it is installed.
WARNING
equipment damage.
1. Start ION Setup.

2. Connect to your meter in advanced mode.
3. Navigate to the GGIO Onboard folder and double-click on the module in the
righthand pane.
4. Select the Setup Registers tab.
5. Select the SPCS Control Mode register that corresponds to the digital output
you want to control through IEC 61850 and click Edit. A dialog appears.
6. Select IEC 61850 CTLVAL from the dropdown list and click OK.
7. Select the Inputs tab.
8. Select the digital output Status register for the digital output that you want to
control through IEC 61850. Click Delete.
NOTE: This digital input register must be deleted in order to prevent a circular
reference that will cause the affected modules to go offline.
9. Click Send to send your changes to the meter.
10.Select the Setup Registers tab and confirm that the Digital Output module’s
setup registers are appropriately configured.
11. Select the Inputs tab.
12.Select the Source register and click Edit.
13.Navigate to the IEC 61850 GGIO Onboard folder and select the SPCS.stVal
output register that corresponds to the digital output.
14.Click OK and Send to save your changes to the meter.
See the ION Reference, available from www.schneider-electric.com, for
information about the IEC 61850 GGIO and Digital output modules.
COMTRADE
Your meter can automatically generate COMTRADE files and store them on the
meter’s internal FTP site.
COMTRADE stands for COMmon format for TRAnsient Data Exchange defined by
IEC 60255-24 edition 2001-05, and defines a common format for power quality
event (disturbance) data in order to simplify retrieval, analysis and exchange of
disturbance data between multiple sources and vendors.
The format of your meter’s COMTRADE files is as defined by IEC 60255-24 edition
2001-05.
76 7EN02-0374-00
COMTRADE is configured as part of the default waveform recording but not

enabled from the factory.
COMTRADE can be used in conjunction with IEC 61850.
NOTE: If you are generating COMTRADE waveform information, the associated
waveform recorders cannot be modified unless COMTRADE is disabled. If the
waveform recorders are not configured identically, COMTRADE waveform
information will not be generated.
See the COMTRADE and ION technology technical note, available from
www.schneider-electric.com, for detailed information about COMTRADE file
formats and implementation.
Related Topics
• FTP
Configuring COMTRADE waveform recording using ION Setup

You can enable and configure COMTRADE waveform recording using ION Setup.
COMTRADE is configured as part of the default waveform recording but not
enabled from the factory.
Your meter’s COMTRADE files’ format complies with the standard defined by IEC
60255-24 edition 2001-05.
COMTRADE records are stored as read-only files on your meter’s internal FTP
server, and are deleted when you perform a Master reset of the meter.
NOTE: To configure waveform recording, you must disable COMTRADE, configure
waveform recording, and then enable COMTRADE. COMTRADE records are not
generated if the waveform recorders have inconsistent settings.
1. Start ION Setup.

3. Navigate to Power Quality and click the COMTRADE.
4. Configure the COMTRADE parameters:
Status Enabled/ Enabled: COMTRADE files are generated.

Disabled Disabled: COMTRADE files are not generated.
Depth 1 or more The number of COMTRADE records stored on the

meter.
• By default the oldest COMTRADE record will be
overwritten by the newest record.
• A message is displayed if the Depth value exceeds
the available memory.
• A single COMTRADE record uses approximately 45
kB of meter memory.
Downloading COMTRADE files using ION Setup

You can download COMTRADE waveform records from the meter’s internal FTP
server to another network location using ION Setup.
1. Start ION Setup.

3. Navigate to Power Quality and click the COMTRADE.
4. Select the status parameter and click Save. The Upload COMTRADE files
7EN02-0374-00 77
5. Select the criteria for the COMTRADE files you want to load from your meter’s
internal FTP site to another network location. Click OK.
NOTE: If no COMTRADE files are downloaded, the ION Setup status bar
provides a descriptive message.
DNP
Your meter can be integrated into a DNP network as a DNP slave.
The Distributed Network Protocol Version 3.0 (DNP 3.0) is an open protocol used
in the electric utility industry for communications and interoperability among
substation computers, Remote Terminal Units (RTUs), Intelligent Electronic
Devices (IEDs, e.g. meters), and master stations.
DNP supported features and default implementation

Your meter is pre-configured for basic DNP Slave functionality.
Your meter supports a maximum of three concurrent connections (sessions) using
the DNP 3.0 protocol; one for each serial port, up to three using Ethernet, or a
combination of both. Combinations available depend on the meter's
communications options. A session consists of all incoming and outgoing DNP
Master/Slave traffic on one of the meter's communications ports.
For serial DNP communications, you must assign the DNP protocol to the
appropriate serial communication port on your meter; you do not have to configure
your meter’s Ethernet port(s).
You can modify your meter’s default DNP map using configuration software.
Data can be imported into the meter from a DNP control relay or analog output
device. This is an advanced feature intended for users with an in-depth
understanding of the DNP 3.0 and ION protocols.
See the online ION Setup help for instructions on connecting to your meter and
accessing the Setup Assistant, which can be used to modify your meter’s DNP port
settings and default DNP map. Go to www.schneider-electric.com to download
your meter’s DNP 3.0 device profile document for detailed information on your
meter’s default DNP map and implementation and the Multiport DNP 3.0 and ION
technology technical note for more information on how your meter supports DNP
3.0.
78 7EN02-0374-00
Time and timekeeping PowerLogic™ ION7400 series
Time and timekeeping

Time overview
Your meter supports different time types and time synchronization methods to
adjust its internal clock.
Your meter’s internal clock is used for keeping time, timestamping data and
determining intervals for time-based measurements. The meter’s clock does not
affect externally logged data.
Your meter monitors the passage of time using the frequency of an internal
oscillator or the frequency of the line power being measured. You can view your
meter’s time and date information using the display or through software. To
improve your meter clock’s accuracy, you can use an external time reference, such
as a Global Positioning System (GPS) signal.
Your meter’s battery maintains the internal clock when the meter is unpowered.
Your meter displays local time based on the meter’s time sync source and settings
for timezone and daylight savings time. You can configure your meter’s date and
time format.
Go to www.schneider-electric.com and download the Time synchronization and
timekeeping technical note for more information about time formats and settings
and the ION Reference for a detailed description of the Clock module and its
operation.
Time synchronization overview

The time synchronization source and the duration between time synchronization
messages determines the accuracy of the meter’s clock.
The clock is adjusted by synchronizing the meter’s time with another time source.
Time synchronization messages can be automatically generated and sent to your
meter from your energy management system software or other time source such
as an SNTP/NTP server or GPS receiver. You can also manually trigger a time
synchronization message from your energy management system or configuration
software.
NOTE: To help maintain data integrity, some energy management systems impose
a blackout rule where time synchronization messages near energy interval
boundaries are ignored.
Supported time synchronization sources

Several time synchronization sources are available to your meter.
• Meter configuration software (ION Setup): Configuration software can manually
synchronize the time of your meter based on the clock of the computer running
the configuration software. Configuration software synchronization is usually
performed when the meter is initially commissioned.
• Energy management system: Energy management systems can synchronize
the time of your meter to be consistent with other meters on the network.
• Simple Network Time Protocol (SNTP): SNTP can synchronize the time of your
meter up to ± 1 second of other meters on an Ethernet network. For SNTP time
synchronization, your meter must be connected to an Ethernet network that has
an active SNTP server and be configured with the server’s information.
• GPS receiver (IRIG-B): A GPS receiver using IRIG-B can synchronize the time
of a meter up to ± 1 ms of Coordinated Universal Time (UTC). A dedicated
serial network is required to implement a GPS scheme. For IRIG-B, one of your
meter’s digital inputs must be connected to the IRIG-B network, and the digital
7EN02-0374-00 79
PowerLogic™ ION7400 series Time and timekeeping
input must be configured for IRIG-B time synchronization in addition to

configuring your meter’s clock.
NOTE: Use the digital inputs located on the meter base for IRIG-B time
synchronization and other high-accuracy applications.
• GPS over serial: A GPS receiver can synchronize the time of a meter up to ± 1
ms of Coordinated Universal Time (UTC). For GPS over serial, your meter’s
serial port must be connected to a GPS receiver, and the serial port
communications must be configured with the correct protocol setting.
• Network Time Protocol (NTP): NTP can typically synchronize the time of a
meter to ± 10 to 100 ms, depending on network configuration. To implement
NTP time synchronization, your meter must be connected to an Ethernet
network that has an active NTP server and be configured with the server’s
information.
Configuring time information using your meter’s display

Use the meter’s display to configure a variety of time parameters.
1. Go to Setup Menu > Date/Time/Clock Setup > Date & Time Setup.
2. Configure your time and date formats, time zone offset, and daylight savings
time offset. Press the down button to access the Clock Setup screen.
3. Configure the clock and time synchronization source, and the time
synchronization time format.
Date/Time/Clock setup
You can configure your meter’s date, time and clock parameters using the display.
Date & time setup
Time Format 12 H, 24 H Specifies how the time is displayed
Date Format MM/DD/YYYY, DD/MM/ Specifies how the date is displayed

YYYY, YYYY/MM/DD
TZ Offset -12:00:00 to 12:00:00 Sets the time zone of the meter’s location,
relative to UTC
DST Offset -3:00:00 to 3:00:00 Sets the daylight savings time offset of the
meter’s location
Clock setup
Clock Source Internal, Line Freq, COMM Specifies the time synchronization source
Time Sync COM1, Ethernet, Specifies the port to receive time

Source Ethernet - ION, Ethernet - synchronization signals
DNP, IRIG-B
Time Sync Type UTC, Local Specifies whether time synchronization signals
are received in local time or UTC
Configuring time and time synchronization using ION Setup

You can set the time and date and configure the time synchronization settings
using ION Setup.
80 7EN02-0374-00
Time and timekeeping PowerLogic™ ION7400 series
NOTE: The clock screen is where you set the start day of the week for the time of
use feature.
NOTE: You must manually adjust the date and time information if the device is
installed in a different time zone location from the computer running ION Setup.
1. Start ION Setup.

3. Navigate to Clock and select the Timezone tab.
4. Select any parameter and click TimeSync to synchronize your device’s date
and time with the computer that is running ION Setup.
5. Click the DST Settings tab to modify your meter’s daylight savings time start
and end dates, if required.
6. Select the parameter that you want to configure and click Edit. Enter the
password if prompted.
Timezone – Sets the timezone based on the timezones available from the computer’s
operating system.
NOTE: This is also where you can synchronize your meter’s DST settings with the
computer’s.
Time sync type Local time or UTC Specifies the time format of the time sync message:
• UTC: Coordinated Universal time: for the purposes of meter configuration, it is
equivalent to Greenwich Mean Time (GMT).
• Local time: the local time, with DST and timezone information applied.
Time sync source COM1, Ethernet, Sets which device port accepts time synchronization messages.
Ethernet - ION, Ethernet Time synchronization messages on other ports are ignored.
- DNP, IRIG-B
Clock Source Internal, Line frequency, Sets the source for the clock:
COMM • Internal: the meter’s internal clock.
• Line frequency: the frequency of the measured power system as the clock
source.
• COMM: the meter’s communication port (used by the GPS time sync source).
DST Offset Numeric Bounded Specifies the amount of time the meter clock is moved forward when entering
Format/Elapsed Interval Daylight Savings. A value of zero disables this feature and clock does not adjust
Format for DST.
Start of the Week Monday - Sunday Specifies the start day of the week used for Trending and Forecasting.
NOTE: Changing the start day of the week clears all trending and forecasting data.
For SNTP/NTP time synchronization, you must set the Time sync type to UTC
and the Time sync source to Ethernet.
For GPS/IRIG-B time synchronization, you must set the Time sync source to
IRIGB and the Clock Source to COMM.
7. For SNTP/NTP time synchronization, you must also enter the following
information under Communications > Network Settings > NTP:
Enable NTP Time Sync NTP, SNTP, No NTP: specifies NTP time synchronization.
SNTP: specifies SNTP time synchronization.
NOTE: SNTP is recommended for revenue-related applications.
No: neither NTP nor SNTP time synchronization are used.
NTP Time Sync Interval Numeric value or elapsed Specifies how often the meter synchronizes over SNTP.
interval value
NOTE: This parameter is not used for NTP.
NTP Event Logging 1000 to 1000000 Specifies the minimum time difference (in milliseconds) for a time synchronization
Threshold (NTP only) to be logged as an event.
This parameter can be configured to help prevent the meter’s event log from being
flooded with time synchronization events.
NTP Server Server IP address or Specifies the IP address (or fully qualified domain name if DNS is active) of the
domain name SNTP or NTP server.
7EN02-0374-00 81
PowerLogic™ ION7400 series Time and timekeeping
8. For serial GPS time synchronization, you must also enter the following
information under Communications > Serial settings:
Protocol Select the GPS setting that matches your GPS receiver.
Baud rate The recommended baud rate for GPS time synchronization is 9600 bps.
Serial port The recommended stop bits/parity for GPS time synchronization is 8N1.
82 7EN02-0374-00
Maintenance PowerLogic™ ION7400 series
Maintenance
Firmware and templates
Firmware and template overview
You can load different firmware versions and templates onto your meter.
Firmware is your meter’s operating system that enables the functions of your
meter. Your meter’s template defines the meter’s features such as its power
measurement and analyzing functionality. Your meter ships from the factory with a
default template, or you can customize your meter’s template to create features
specific to your meter’s application. You can save your customized template and
upload it to other meters of the same type.
You can view your meter’s firmware version on your meter’s display, webpages
and through ION Setup.
You can upgrade your meter’s firmware and template using ION Setup. Firmware
updates and new factory templates are available for download from
Firmware overview
Firmware is your meter’s operating system.
When new firmware is available for your meter, you can upgrade to the latest
version to get the added features and functionality. The firmware version loaded on
your meter is shown on your meter’s display. You can use ION Setup to upgrade
the firmware on your meter.
The meter’s firmware includes a digital signature, which helps ensure the
firmware’s authenticity.
You must load a meter template as part of the firmware upgrade process. You can
save your meter’s existing template before performing a firmware upgrade and
then reload it back onto the meter if you do not want to change your meter’s
template.
Your meter’s remote display and option modules use firmware information from the
meter, but they may also need to have their internal firmware updated to support
new or improved features. To load and update to your meter’s remote display
firmware, you need to copy the file to your meter’s internal FTP server. You can
download firmware files from www.schneider-electric.com.
See the online ION Setup help, available from www.schneider-electric.com, for
more information about downloading, saving and loading your meter’s template.
Typical workflows
To update your meter to the latest available firmware and factory template:
• Download the latest firmware and template for your meter.
• Load the firmware onto your meter; the firmware upgrade process includes
upgrading the meter template.
To take an existing meter out of service and replace it with a new meter:
• Save the template from the existing meter
• Load the existing meter’s template onto the new meter; the new meter will now
have the customized features from the existing meter.
To update your meter’s firmware without updating your meter’s template:
• Save your meter’s template.
• Download the latest firmware.
7EN02-0374-00 83
PowerLogic™ ION7400 series Maintenance
• Load the firmware onto your meter. When prompted for a template file, select
the template you saved from your meter.
To update the firmware on your meter’s remote display:
• Download the display firmware.
• Load the firmware onto the meter’s internal FTP site using either an FTP
program or ION Setup. The results of the firmware update are stored in the
meter’s event log.
To update the firmware on your meter’s option module(s):
• Download the option module firmware; make sure that the firmware matches
the option module type.
• Load the firmware onto the meter’s internal FTP site using either an FTP
program or ION Setup.
• Power cycle or perform an option bus reset to start the option module firmware
NOTE: If the meter is power cycled or an option module reset is performed while
there are option module firmware upgrade files loaded on the meter’s FTP site, the
option module firmware is upgraded.
Visit the company website at www.schneider-electric.com and search for your
meter type to see the available firmware and templates.
See the online ION Setup help for instructions on how to load meter templates.
Laptop computer upgrade considerations

The connection between the laptop and the device must be maintained in order for
the upgrade to proceed.
Laptop computers generally have different default power properties than desktop
computers.
If the laptop’s hard disk shuts down or the laptop enters system standby mode, this
connection is broken and the upgrade procedure must be restarted.
If you are upgrading your meter’s firmware using a laptop computer, follow these
guidelines:
• Plug the laptop computer into a wall outlet. Do not run the laptop on its battery.
• Configure the laptop’s hard disks so that they do not shut down after a certain
period of time (for example, set to “never”).
• Turn off the laptop’s power suspension (for example, system stand-by) and
hibernate options.
• Disable the laptop’s option to power down when it is closed. This prevents a
shut down if the laptop is accidentally closed.
• Disable the laptop’s screen saver as they can burden the CPU.
Firmware upgrade considerations

Ensure that the firmware version you are upgrading to is compatible with your
meter, and that the version number is greater than your existing firmware (or else
you will downgrade your meter).
Your meter’s existing template may not work with different firmware versions if
significant meter features have been added or modified.
Remote display (RMD) upgrade behavior

Your meter’s remote display will upgrade as soon as the upgrade file is put in the
remote display upgrade folder on your meter’s internal FTP site. It is deleted as
part of the upgrade process.
NOTE: If your meter’s remote display loses power during firmware upload, the
display will revert to its original firmware and you will have to reload the firmware
file.
84 7EN02-0374-00
The results of your remote display firmware upgrade are stored in your meter’s
event log. Detailed information about your remote display, such as serial number
and firmware version is provided in the Factory module.
information about the Factory module.
Option module(s) upgrade behavior

To upgrade option modules, you must load the upgrade file into the appropriate
folder on the meter’s internal FTP site. The upgrade is triggered by either a power
cycle or option module reset. After the upgrade is performed, the upgrade file is
deleted from the meter’s internal FTP site before the option module is reset to run
the new firmware. The option module firmware will not upgrade if more than one
upgrade file is in the folder. The upgrade file must be the correct file type and
match the type of module being upgraded.
All option modules do not perform their regular functions during firmware upgrade.
If more than one option module is being upgraded, the firmware on the option
module closest to the meter is done first, then the next closest, proceeding to the
furthest module from the meter base requiring upgrading. A single option module
firmware upgrade should not take more than five minutes.
The option module upgrade results are stored in your meter’s event log. Detailed
information about the option module, such as serial number and firmware version
is provided in the Factory module. Information about the option module type and
details of the option module’s state is provided in the Diagnostics module.
information about the Factory and Diagnostic modules.
Loading meter firmware using ION Setup

You can load firmware onto your meter using ION Setup.
You can download firmware for your meter from www.schneider-electric.com.
You must load a meter template as part of the firmware upgrade process. You can
save your meter’s existing template by navigating to Template > Save to PC in the
ION Setup Assistant and clicking Save to save your meter’s template as a .DCF
file. You can also use a template that you have saved from another meter of the
same type, or download a factory template from www.schneider-electric.com.
Ensure that you record your meter’s user and password information in a secure
location before upgrading the meter’s firmware. If your meter’s user and password
information is lost, you must return the meter for factory reconfiguration, which
resets your meter to its factory defaults and destroys all logged data.
Your meter’s digital and analog outputs may change state during a firmware
upgrade.
WARNING
equipment damage.
Loading firmware or template onto your meter clears the meter’s recorded data.
7EN02-0374-00 85
NOTICE
DATA LOSS
Ensure that all important data has been recorded before uploading firmware or a
template to your device.
Failure to follow these instructions can result in data loss.
1. Obtain the meter firmware (.UPG) and framework (.DCF) that you want to load
onto your meter. Save the files where they can be accessed by the computer
running ION Setup.
2. Start ION Setup.
4. Select the Template screen.
5. Click the Firmware Upgrade tab, then click Upgrade. Enter your meter’s
password (if prompted) and click OK.
6. Navigate to the meter firmware (.UPG) file and click Open. Enter your ION
Setup password when prompted and click OK.
7. Navigate to the meter framework (.DCF) file and click OK.
The Template Paste Options dialog box appears.
8. Select the check boxes for the settings you want to retain (not overwrite) and
click OK.
A dialog box describes the template upload and firmware upgrade progress,
verifies the firmware, and finishes with an overview stating whether the firmware
and framework were successfully uploaded onto your meter.
Loading option module firmware using ION Setup

You can upload firmware to your meter’s option modules using ION Setup over an
Ethernet connection.
You can only upload firmware to the same type of module; if you have different
types of option modules connected to your meter, you must perform the upload
process for each module type.
You must have:
• Your meter’s option module firmware upgrade (.SI9) file. You can download
upgrade files from www.schneider-electric.com.
• The option module connected to your meter, and have access to your meter’s
internal FTP site.
All option modules do not perform their regular functions during firmware upgrade;
they will not communicate to the meter and the outputs may change state during
the upgrade process.
WARNING
equipment damage.
1. Obtain the option module firmware (.SI9) files that you want to load onto your
option module(s). Save the files where they can be accessed by the computer
running ION Setup.
86 7EN02-0374-00
2. Start ION Setup.

6. Navigate to where you have stored the option module firmware. Select the
Option Module firmware file (*.SI9) as the file type.
7. Select the option module firmware (.SI9) file and click Open.
8. Enter your ION Setup password when prompted and click OK.
A dialog box describes the firmware upgrade progress, verifies the firmware, and
finishes with an overview stating whether the firmware was successfully uploaded.
Loading remote display firmware using ION Setup

This procedure is specific to the DIN meters with a remote display, and cannot be
performed on meters with an integrated display.
You can load updates to your meter’s remote display firmware using ION Setup
over an Ethernet connection.
You must have:
• Your meter’s remote display firmware update (.BIN) file. You can download
update files from www.schneider-electric.com.
• The remote display connected to your meter.
NOTE: If your meter’s remote display loses power during firmware upload, the
display will revert to its original firmware and you will have to reload the firmware
file.
1. Obtain the remote display firmware (.BIN) that you want to load onto your
display. Save the files where they can be accessed by the computer running
ION Setup.
2. Start ION Setup.
6. Navigate to where you have stored the remote display firmware. Select the
remote display firmware file (*.BIN) as the file type.
7. Select the remote display firmware (.BIN) file and click Open.
8. Enter your ION Setup password when prompted and click OK.
A dialog box describes the firmware upgrade progress, verifies the firmware, and
finishes with an overview stating whether the firmware was successfully uploaded.
Loading option module firmware using FTP

You can upload firmware to your meter’s option modules by loading the firmware
upgrade file onto your meter’s internal FTP site.
You must have:
• Your meter’s option module firmware upgrade (.SI9) file(s). You can download
• The option module connected to your meter, and have access to your meter’s
internal FTP site.
7EN02-0374-00 87
upgrade. Option modules are offline during an option module firmware upgrade;
WARNING
equipment damage.
NOTE: If your meter’s option module loses power during firmware upload, the
option module will revert to its original firmware and you will have to reload the
firmware file.
1. Connect to your meter’s internal FTP site. Open the remote display upgrade
(rmdUpg) folder.
2. Drag the remote display firmware file into the remote display upgrade folder.
The file is immediately transferred to the remote display, and is not stored on
the meter.
3. Watch your meter’s display to confirm the firmware upgrade is taking place.
4. Review the remote display firmware upgrade details stored in the meter’s event
log to confirm that the upload was successful.
Loading remote display firmware using FTP

You can upload firmware to your meter’s remote display by loading the firmware
upgrade file onto your meter’s internal FTP site.
You must have:
• Your meter’s remote display firmware upgrade (.BIN) file. You can download
• The remote display connected to your meter, and have access to your meter’s
internal FTP site.
1. Connect to your meter’s internal FTP site.

2. Open the remote display upgrade (rmdUpg) folder.
3. Drag the remote display firmware file into the remote display upgrade folder.
The file is immediately transferred to the remote display, and is not stored on
the meter.
4. Watch your meter’s display to confirm the firmware upgrade is taking place.
5. Review the remote display firmware upgrade details stored in the meter’s event
log to confirm that the upload was successful.
Related Topics
• Accessing your meter’s FTP server
• Remote display troubleshooting icons
• Event log overview
Test mode
Test mode is typically used for verifying meter functions.
88 7EN02-0374-00
The meter is usually reading data from a test power supply while function
verification is performed.
The values shown in the test mode display screens represent different
accumulators than those shown in norm or alt mode (although they perform some
of the same basic measurements). The test mode display values are for accuracy
checking purposes; they only accumulate while the meter is in test mode.
You can create custom test mode screens and modify the existing test mode
screens.
NOTE: You cannot place revenue-locked meters into test mode.
Several things to note about test mode:
• All of the billing quantities that are recorded when the meter is in Normal mode
stop accumulating when the meter is switched to test mode – the data is sent to
special test mode registers instead.
• The values accumulated in these test registers are displayed on the test mode
displays and in ION Setup.
• The regular normal mode billing registers are unaffected while the meter is in
test mode; accumulation of this data continues as soon as you exit test mode.
• All test registers are reset to zero when you exit test mode.
Test mode default screens

Your meter has default test mode display screens.
NOTE: You can modify the test mode display screens or add custom screens using
ION Setup.
Screen Description
Demand test This screen shows test mode kW delivered and received values. Both quantities
are produced from a sliding window (rolling block) demand calculation.
Reactive energy This screen shows test mode kVARh delivered and received values.
test
Active energy This screen shows test mode kWh delivered and received values.
test
Placing your meter in test mode using the display

You can put your meter into test mode using the display.
NOTE: You cannot place a revenue-locked meter into test mode.
1. Navigate to the display modes selection screen and select Test Mode. The test
mode menu is shown before the meter goes to the first test mode screen.
2. View the test mode screens by pressing the up or down buttons.
To exit test mode, press the home button to view the test mode menu, and
select Exit Test Mode to go to the display modes selection screen.
Placing your meter in test mode using ION Setup

You can put your meter into test mode using the ION Setup.
NOTE: You cannot place a revenue-locked meter into test mode.
1. Start ION Setup.

3. Navigate to Verification and select the Verification tab.
4. Select Test Mode and click Display.
Your meter is now in test mode, and the Test Mode screen is displayed.
7EN02-0374-00 89
5. Select the different tabs to view your meter’s test mode values and modify test
mode parameters.
6. Click Close to take your meter out of test mode.
Test mode data and parameters available through ION Setup
Tab Data Parameters

Energy • kWh, kVARh, kVAh delivered • Force TLC (transformer loss
and received compensation)
• Loss compensation status • Scaling
• Test Reset
Rolling Demand • kW and kW peak demand • Peak Reset
• Test demand settings • Test Reset
Volts, Amps and • kW, kVAR • Force TLC (transformer loss

Power • Harmonics compensation)
• Average, total values • Loss Mode
• Power factor, frequency • Test Reset
Troubleshooting
Technical assistance
Visit www.schneider-electric.com for support and assistance with lost passwords
or other technical problems with the meter.
Make sure you include your meter’s model, serial number and firmware version in
your email or have it readily available if calling Technical Support.
Option module troubleshooting

Your meter’s option modules operate sequentially; if one module is non-functional
all downstream modules may be affected.
If your meter cannot communicate with an option module, by default it cycles
power to that module and all downstream modules, making multiple attempts to
communicate. After the maximum number of communication attempts has been
exceeded the meter will remove power to that module and all downstream
modules.
When troubleshooting option modules, attach each option module directly to the
meter and verify its operation. If each option module operates when directly
connected, use combinations of modules or known good modules to help identify
the issue.
Events related to option module initialization and operation are stored in your
meter’s onboard event log. Perform an option bus reset to restart the option bus
and re-initialize the option modules attached to your meter.
Information about your option module’s type, serial number, firmware version and
present status is available in the Factory and Diagnostics modules.
information about the Factory and Diagnostics modules.
90 7EN02-0374-00
Meter webpages PowerLogic™ ION7400 series
Meter webpages
Webpage interface
Your meter comes with default webpages that contain typical elements.
A Meter type and model, device name
B Username
C Main menu
D Webpage menu
E Webpage content
NOTE: This graphic is representative only, and your meter’s webpages may
appear differently than shown.
Default meter webpages

Default webpages are available on your meter.
Main menu Webpage menu Webpage content
Monitoring Instantaneous Readings • Basic readings

• Energy readings
• Demand readings
• Voltage readings
• Power Quality
Trending & Forecasting Select the target and interval for trending and forecasting and view
the results.
Power Quality Summary • Harmonics
• ITI (CBEMA)-SEMI
• NEMA Motor Derating Curve
• EN50160
Inputs/Outputs • Digital inputs
• Digital outputs
• Analog inputs
• Analog outputs
Control Resets Perform resets, and view when previous resets were performed.
Diagnostics Statistics • Communications

• Ethernet
• Serial port
7EN02-0374-00 91
PowerLogic™ ION7400 series Meter webpages
Main menu Webpage menu Webpage content
• Meter - Basic
• Meter - Advanced
Phasor diagram View the phasor diagram and numeric values.
Setup Ethernet • Basic Settings

• Advanced settings
Serial Port • Basic Settings

• Advanced settings
SNMP Parameters Configure your meter’s SNMP parameters.
NTP Configure your meter’s NTP parameters.
SMTP Configure your meter’s SMTP parameters.
Date & Time Configure your meter’s time and time synchronization.
Preferences Enter your meter’s nameplate information.
Metering Configure the parameters that impact metered data.
Maintenance1 — Custom. No default content.

1By default the Maintenance menu is empty, and the menu is not displayed until information is added to it.
Accessing the meter’s webpages for data viewing and meter

configuration
You can access the meter’s webpages through the meter’s Ethernet connection
using a web browser.
You must have cookies enabled in order to access your meter’s webpages.
You may need to configure your meter’s security settings in order to view
webpages and configure your meter using webpages.
If you configure communications so that you can no longer communicate to and
configure your meter, you must return the meter to the factory, where your meter is
reset to its factory defaults and all logged data is lost.
NOTICE
DATA LOSS
Ensure you maintain sufficient access to communicate to and configure your
device.
Failure to follow these instructions may result in data loss.
1. Open a web browser and enter your meter’s IP address in the address box.
The webpage login prompt is displayed.
2. Enter a valid username and password.
NOTE: The username and password are defined by your meter’s security
configuration; if standard security is enabled, the password is the same as the
display password with a default username of 7400. The default display
password is 0 (zero). To help increase the security of your meter’s configuration
and data, configure your meter’s username and passwords to be different from
the default values.
3. Select your desired Language from the dropdown list, and click Log In.
Your meter’s webpages are displayed. The default page is the Monitoring
webpage, showing real-time data.
92 7EN02-0374-00
4. Select the main menu tab that corresponds to the category of information you
want to view, and select the webpage menu from the list on the left.
The webpage content is displayed.
5. Click the webpage content headings to expand and view the meter’s data.
6. Select Setup to view and edit your meter’s configuration.
Related Topics
• Trending and forecasting overview
• Security overview
Viewing files using your meter’s webpages

You can load files of a variety of standard formats, such as *.pdf, *.jpg and *.png
into the webpage folders on your meter’s internal FTP site where they can be
viewed using your meter’s webpages.
Videos in *.mp4 format can be played in most browsers. The filenames must be
compatible with your meter’s FTP filename requirements.
NOTE: Image files are shown at full-size (100%). Scale images to the desired size
before loading them onto your meter’s internal FTP site.
1. Access your meter’s internal FTP site.

2. Open the web folder. Copy your file into the subfolder that corresponds to the
webpage main menu tab you want to access your file from.
3. Connect to your meter’s webpages. Select the main menu item that
corresponds to the folder where you stored your file in step 2. Your file is listed
in the webpage menu.
4. Select your file from the webpage menu to view.
Example
To view a schematic diagram (oneline.pdf) of your power system from the
Monitoring menu of your meter’s webpages:
1. Access your meter’s internal FTP site.
2. Copy oneline.pdf into web > monitoring.
3. Access your meter’s internal webpages and select the Monitoring menu.
4. In the webpage menu click oneline.pdf to view your power system schematic.
Related Topics
• FTP filename requirements
• FTP
Creating custom webpages for your meter

You can create custom webpages to view data or access configuration parameters
from your meter.
Download the your meter’s Modbus registers map from

2. Go to web > examples. Select samplereadings.html to create a data value
webpage, or select sampleconfiguration.html to create a configuration
parameters webpage.
7EN02-0374-00 93
3. Save a copy of the sample file. This filename is the webpage name.
4. Open your webpage in an HTML or webpage editor program.
5. Modify the webpage to reference the desired meter data or parameters from the
Modbus registers map, and update the other fields where required.
6. Save your custom webpage.
The meter will display translated content if it exists in the meter’s memory. If
translated content is not available, English is displayed.
– If you have created a data viewing webpage, copy your custom webpage to
web > monitoring.
– If you have created a configuration webpage, copy your custom webpage to
web > setup.
8. Login to your meter’s webpages.
Your custom webpage is available from the webpage menu under the monitoring
(data viewing) or setup (configuration) tab.
Related Topics
• FTP
Sample data viewing webpage

You can create custom data viewing webpages using the sample webpage stored
on your meter.
The sample webpages are stored in the documents folder on your meter’s internal
FTP site.
Your meter’s Modbus register map is available from www.schneider-electric.com.
If required, your meter’s ION handles document is packaged with the meter
firmware file which is available for download from www.schneider-electric.com.
The data viewing webpage must be stored on your meter’s internal FTP site in the
folder for Monitoring. The custom webpage is viewed by selecting the Monitoring
main menu tab on your meter’s webpage.
Configuring the HTML code other than where described is an advanced procedure
and should only be performed by those with an advanced understanding of
webpages and how your meter processes them.
Sample webpage data viewing result

appear different than shown.
A HTML filename
B Content pane title
C Row heading
D Units
E Column heading
94 7EN02-0374-00
F Named register instantaneous value
G Second content pane A title
Sample HTML code for data viewing webpage content

Content and formatting of a data viewing webpage is controlled by its HTML code.
Sample data viewing webpage content
Line # Sample HTML
1 SampleMonitorPane.html
2 <div class="content-fit">
3 <div class="accordion">
4 <h3 target="sample-readings">$%localizedString(Basic Readings)#$</h3>
5 <div id="sample-readings">
6 <table class="datatable">
7 <tr>
8 <th> </th>
9 <th>$%localizedString(Minimum)#$</th>
10 <th>$%localizedString(Present)#$</th>
11 <th>$%localizedString(Maximum)#$</th>
12 </tr>
13 <tr class="minor">
14 <td>$%localizedString(I a)#$ <span unitsreg="I a"></span></td>
15 <td regname="I a mn"></td>
16 <td regname="I a"></td>
17 <td regname="I a mx"></td>
18 </tr>
20 <td>$%localizedString(I b)#$ <span unitsreg="I b"></span></td>
21 <td regname="I b mn"></td>
22 <td regname="I b"></td>
23 <td regname="I b mx"></td>
24 </tr>
25 </table>
26 </div>
27 <h3 target="sample-energy">$%localizedString(Energy Readings)#$</h3>
28 <div id="sample-energy">
29 <table class="datatable">
30 <tr>
31 <th> </th>
33 </tr>
34 <tr>
35 <td>$%localizedString(Active Energy)#$ <span unitsreg="kWh del-rec"></span></td>
36 <td regname="kWh del-rec"></td>
37 </tr>
7EN02-0374-00 95
Sample data viewing webpage content
Line # Sample HTML
38 <tr>
39 <td>$%localizedString(Reactive Energy)#$ <span unitsreg="kVARh del-rec"></span></td>
40 <td regname="kVARh del-rec"></td>
41 </tr>
42 </table>
43 </div>
44 </div>
45
46
47 <script type="text/javascript">
48
49 instantaneousReadings.initInstantaneousReadings('sample-readings');
50
51 </script>
52 </div>
Sample webpage data viewing content description
Line # Description
1 SampleMonitorPane.html
The HTML filename, including the HTML extension (.html). This filename must comply with FTP filename conventions (no
spaces or special characters). The filename (without the HTML extension) is the name shown on the webpage menu.
4 <h3 target="sample-readings">
This creates the first webpage content pane. “sample-readings” is the name of the webpage content. This name must be
unique.
$%localizedString(Basic Readings)#$</h3>
Basic Readings is the title of the webpage content pane. This title is translated if possible.
5 <div id="sample-readings">
This must match the name of the webpage content in line 4.
9 <th>$%localizedString(Minimum)#$</th>
Minimum is the heading for the first column. This heading is translated if possible.
Present is the heading for the second column. This heading is translated if possible.
11 <th>$%localizedString(Maximum)#$</th>
Maximum is the heading for the last column. This heading is translated if possible.
14 <td>$%localizedString(I a)#$
I a is the row heading. This heading is translated if possible.
<span unitsreg="I a"></span></td>
This displays the units that the meter has defined for the named register I a.
15 <td regname="I a mn"></td>

This displays the instantaneous value of the named register I a mn.
16 <td regname="I a"></td>

This displays the instantaneous value of the named register I a.
17 <td regname="I a mx"></td>

This displays the instantaneous value of the named register I a mx.
20 <td>$%localizedString(I b)#$
I b is the second row heading. This heading is translated if possible.
<span unitsreg="I b"></span></td>
This displays the units that the meter has defined for the named register I b.
21 <td regname="I b mn"></td>

This displays the instantaneous value of the named register I b mn.
22 <td regname="I b"></td>

This displays the instantaneous value of the named register I b.
96 7EN02-0374-00
Sample webpage data viewing content description
Line # Description
23 <td regname="I b mx"></td>

This displays the instantaneous value of the named register I bmx.
27 <h3 target="sample-energy">
This creates the second webpage content pane. Sample-energy is the name of the webpage content. This name must be
unique.
$%localizedString(Energy Readings)#$</h3>
Energy Readings is the title of the webpage content pane. This title is translated if possible.
28 <div id="sample-energy">
Present is the heading for the last column. This heading is translated if possible.
35 <td>$%localizedString(Active Energy)#$
Active Energy is the row heading. This heading is translated if possible.
<span unitsreg="kWh del-rec"></span></td>
This displays the units that the meter has defined for the named register kWh del-rec.
36 <td regname="kWh del-rec"></td>

This displays the instantaneous value of the named register kWh del-rec.1
39 <td>$%localizedString(Reactive Energy)#$
Reactive Energy is the row heading. This heading is translated if possible.
<span unitsreg="kVARh del-rec"></span></td>
This displays the units that the meter has defined for the named register kVARh del-rec.
40 <td regname="kVARh del-rec"></td>

This displays the instantaneous value of the named register kVARh del-rec.1
49 instantaneousReadings.initInstantaneousReadings('sample-readings');
Sample-readings is the unique name of the first webpage content name. This HTML code updates all of the webpage’s
values.
1Named registers are listed in the Modbus registers map. If the desired value is not listed, you can reference the value by its ION handle,
using the following format: <td regname=”_0x####”</td>, where #### is the hexadecimal value of the ION handle.
Sample setup webpage

You can create custom setup webpages using the sample webpage stored on your
meter.
Sample webpages are stored in the documents folder on your meter’s internal FTP
site.
Your meter’s Modbus register map is available from Schneider Electric.
If required, your meter’s ION handles document is packaged with the meter
firmware file which is available for download from www.schneider-electric.com.
Custom setup webpages must be stored on your meter’s internal FTP site in the
folder for Setup. The custom webpage is viewed by selecting the Setup main menu
tab on your meter’s webpage.
Configuring the HTML code other than where described is an advanced procedure
and should only be performed by those with an advanced understanding of
webpages and how your meter processes them.
Sample webpage setup result

7EN02-0374-00 97
A HTML filename
B Content pane title
C Sub-heading
D Row heading
E Named register value
F Second content pane title
Sample HTML code for setup webpage content

Content and formatting of a setup webpage is controlled by its HTML code.
Sample setup webpage content
Line # Sample HTML
1 SampleSetupPane.html
2
3 <div class="content-fit">
4 <form id="formSampleSettings">
5
6 <div class="accordion">
7 <h3 target="sample-basic">$%localizedString(Basic Settings)#$</h3>
8 <div id="sample-basic">
9 <table class="formtable">
10 <tr>
11 <th> </th>
12 <th> </th>
13 </tr>
14 <tr>
15 <td>$%localizedString(Ethernet)#$</td>
16 <td> </td>
17 </tr>
19 <td>$%localizedString(MAC Address)#$</td>
20 <td regname="MAC Address"></td>
21 </tr>
23 <td>$%localizedString(Ethernet Device Name)#$</td>
24 <td><input name="Ethernet Device Name" type="text" /></td>
25 </tr>
98 7EN02-0374-00
Sample setup webpage content
Line # Sample HTML
27 <td>$%localizedString(IP Address)#$</td>
28 <td><input name="IP Address" type="text" /></td>
29 </tr>
30 </table>
31
32 </div>
33
34 <h3 target="sample-advanced">$%localizedString(Advanced Settings)#$</h3>
35 <div id="sample-advanced">
36 <table class="formtable" id="frameFormatDropdownContainer">
37 <tr>
38 <th> </th>
39 <th> </th>
40 </tr>
41 <tr>
42 <td>$%localizedString(TCP Keep Alive Minutes)#$</td>
43 <td><input type="text" name="TCP Keep Alive Minutes" class="small" /> <span unitsreg="TCP Keep
Alive Minutes"></span></td>
44 </tr>
45 <tr>
46 <td>$%localizedString(Enable Web Server)#$</td>
47 <td><select name="Enable Web Server"></select> </td>
48 </tr>
49 </table>
50
51 </div>
52 </div>
53
54 <input type="submit" class="apply" value='$%localizedString(Apply)#$' />
55
56 </form>
57
58
59 <script type="text/javascript">
60
61 SetupPane.init('formSampleSettings');
62 formChangeDetection.initFormChangeDetection('#formSampleSettings', '#dialogFormChanges');
63
64 </script>
65 </div>
7EN02-0374-00 99
Sample setup webpage content description
Line # Description
1 SampleSetupPane.html
The HTML filename, including the HTML extension (.html). This filename must comply with FTP filename conventions (no
spaces or special characters). The filename (without the HTML extension) is the name shown on the webpage menu.
4 <form id="formSampleSettings">
“formSampleSettings” is the name of the webpage content. This name must be unique
7 <h3 target="sample-basic">
This creates the first webpage content pane. “sample-basic” is the name of the webpage content. This name must be
unique.
$%localizedString(Basic Settings)#$</h3>
Basic Settings is the title of the webpage content pane. This title is translated if possible.
8 <div id="sample-basic">
15 <td>$%localizedString(Ethernet)#$</td>
Ethernet is the subheading. This heading is translated if possible.
19 <td>$%localizedString(MAC Address)#$</td>
MAC Address is the row heading. This heading is translated if possible.
20 <td regname="MAC Address"></td>

This displays the value of the read-only named register MAC Address.
23 <td>$%localizedString(Ethernet Device Name)#$</td>

Ethernet Device Name is the row heading. This heading is translated if possible.
24 <td><input name="Ethernet Device Name" type="text" /></td>

This displays the instantaneous value of the configurable named register Ethernet Device Name in a text-edit field.
The type must match the named register type, in this case, an alphanumeric string.
27 <td>$%localizedString(IP Address)#$</td>
IP Address is the row heading. This heading is translated if possible.
28 <td><input name="IP Address" type="text" /></td>

This displays the instantaneous value of the configurable named register IP Address in a text-edit field.
34 <h3 target="sample-advanced">
This creates the second webpage content pane. Sample-advanced is the name of the webpage content. This name must be
unique.
$%localizedString(Advanced Settings)#$</h3>
Advanced Settings is the title of the webpage content pane. This title is translated if possible.
35 <div id="sample-advanced">
42 <td>$%localizedString(TCP Keep Alive Minutes)#$</td>

TCP Keep Alive Minutes is the row heading. This heading is translated if possible.
43 <td><input type="text" name="TCP Keep Alive Minutes" class="small" />

This displays the instantaneous value of the configurable named register TCP Keep Alive Minutes in a text-edit field.
<span unitsreg="TCP Keep Alive Minutes"></span></td>
This displays the units that the meter has defined for the named register TCP Keep Alive Minutes.
NOTE: There are no defined units for TCP Keep Alive Minutes, so no units are displayed.
46 <td>$%localizedString(Enable Web Server)#$</td>

Enable Web Server is the row heading. This heading is translated if possible.
47 <td><select name="Enable Web Server"></select> </td>

Enable Web Server is the named register that is displayed. Named registers are listed in the meter’s registers map.
The type must match the named register type, in this case, an enumerated value that is displayed as a drop-down list.
100 7EN02-0374-00
Sample setup webpage content description
Line # Description
61 SetupPane.init('formSampleSettings');
This must match the webpage content name from line 4.
62 formChangeDetection.initFormChangeDetection('#formSampleSettings', '#dialogFormChanges');
This must match the webpage content name from line 4. This HTML code updates all of the webpage’s values.
7EN02-0374-00 101
PowerLogic™ ION7400 series Logging
Logging
Logging overview
The meter is equipped with data recorders that enable you to log and monitor
various metering functions and features.
Your meter can support up to 50 logs (data recorders) which can each record up to
16 different parameters.
Your meter has a number of onboard default logs (also called data recorders) that
are used to store data related to:
• Power quality and compliance
• Trending and forecasting
• Energy/revenue metering
• Meter events
Your meter also logs voltage and current waveform data when a sag or swell is
detected. You must enter your power system’s nominal values and configure your
meter so that it can identify sags and swells. You can configure your meter’s
setpoint learning feature to learn your power system’s normal operating values and
use that information to help identify voltage sags and swells.
Logged data can be retrieved by energy management software.
Related Topics
Default logging capacity

Your meter’s preconfigured data and waveform recorders have default logging
depths and intervals.
Data recorder number Log name Depth Interval
1 Revenue Log 3360 (35 days) 900 seconds (15 minutes)
9 Loss Log 3360 (35 days) 900 seconds (15 minutes)
2, 3, 4 Historic Logs 3360 (35 days) 900 seconds (15 minutes)
39 Daily Nominal Log 450 Triggered on demand
7, 8 Harmonics Logs 840 (35 days) 3600 seconds (1 hour)
N/A Waveform recorders (6 total) 30 Triggered on demand
N/A COMTRADE records 1 Triggered by waveform recording
10 Energy/demand (EgyDmd Log) 3360 (35 days) 900 seconds (15 minutes)
5 Sag/swell Log 100 Triggered on demand
N/A Event Log 500 Triggered on demand
11 - 14, 17, 19 - 26, 28, EN50160 Logs varies EN50160 intervals

29, 32, 35
6, 16, 37, 38, 40 4-30 Logs varies IEC61000-4-30 intervals
Log depth configuration

You can change the number of records (depth) stored in the log.
Use ION Setup to change the number of records (depth) stored in the log.
Changing how the log records information (circular, or stop-when-full) is an
102 7EN02-0374-00
Logging PowerLogic™ ION7400 series
advanced procedure to change the RecordMode setup register in the Data

Recorder and Waveform Recorder modules.
Data logs and circular format waveform recorders have a minimum depth of 2
records.
Log interval configuration

You can change the logging intervals for the revenue and energy demand log.
Use ION Setup to change the logging intervals for the revenue and energy demand
log.
Changing the interval for other data logs is an advanced procedure to modify the
Periodic Timer module’s Period setup register, which triggers the data log’s
recording.
Do not change the Periodic Timer module’s Sync Mode setup register.
The default Periodic Timer modules that control the frequency of different data
recording are as follows:
• Revenue Log Trg: controls the frequency of the logging of revenue values
• Loss Log Trg: controls the frequency of Loss Compensation Data logging
• EgyDmd Log Trg: controls the frequency of logging for the Energy and Demand
Log (this log is used by Power Monitoring Expert software to generate reports.
• Hist Log Trg: controls the frequency of Historic Data logging
• Harm Log Trg: controls the frequency of Harmonics logging
Programming your meter to write to any data recorder at continuous intervals
shorter than 60 seconds (heavy logging configuration) can cause loss of data in
the event of a power failure.
NOTICE
DATA LOSS
Use an uninterruptible power supply (UPS) if you program your meter for heavy
logging.
Data log memory calculations

The amount of memory required to store data and event logs depends on the
number of parameters being logged and the frequency with which these
parameters are logged.
The memory required is calculated as follows:
Memory consumption for each record (in Bytes) = [(number of parameters x 5) + 8]
For example, a data log recording three parameters consumes 23 Bytes of data. If
the data is recorded every 15 minutes for 35 days, the data log requires
approximately 80 kiloBytes of logging memory.
Waveform record memory calculations

The meter can simultaneously capture waveforms triggered by events on all
channels to a maximum of 96 cycles for each waveform record.
The memory required is calculated as follows:
7EN02-0374-00 103
Memory consumption for each waveform (in Bytes) = [2 x number of samples per
cycle + 12] x [number of cycles in waveform x 2] + 32.
A single waveform record requires approximately 8 kB of memory.
See the ION Setup online help, available from www.schneider-electric.com, for
more information about the logging memory allocations and other meter logging
memory information displayed by the ION Setup Assistant.
Data logging overview

Your meter has data logging capabilities, including a special type of data log which
is an event log, which logs prioritized events.
Data logs are recorded by your meter and stored in the meter’s memory inside
configurable data logs. Your meter’s data logs are retained if the meter loses
power.
Logged data can be used by energy management software. Logs can be
configured to either overwrite the oldest data when full (circular), or to stop writing
data to the log when the number of logged records reaches the maximum log
depth (stop-when-full).
Your meter ships with a comprehensive data-logging configuration consisting of
data logs set up to record values at specific intervals or on conditions. Your meter’s
default data logging configuration should be sufficient for most applications, but
you can also reconfigure existing logs or create new logs for custom applications if
needed.
Your meter can also be configured to email data log information.
NOTE: Adding or deleting data logs or their parameters outside of the ION Setup
Assistant should only be undertaken by those with an advanced understanding of
ION architecture and their meter’s template.
See the Internal email client feature technical note, available from
www.schneider-electric.com, for instructions on how to configure your meter to
email logged data.
information about ION architecture and ION modules.
Default data logging configuration

Your meter is equipped with preconfigured data logs which you can modify.
The default data logging configuration might be used by other components of your
power monitoring system. Do not change the default configuration of any of the
logs unless you understand the impact of the change on these power monitoring
system components, the data they use and your meter’s memory.
Revenue log
The Revenue Log is configured for use with UTS MV-90 billing software. The
default values logged by the Revenue Log are as follows:
kWh del int Interval kWh delivered

kWh rec int Interval kWh received
kVARh del int Interval kVARh delivered
kVARh rec int Interval kVARh received
104 7EN02-0374-00
Historic data logs

Three historic data logs are used to record standard power system quantities, such
as phase current, phase voltage and power factor. These logs are labeled Hist
Mean Log, Hist High Log, and Hist Low Log. By default, they log the following
values:
Hist High Log
Vll ab high I avg high
Vll bc high I 4 high
Vll ca high kW tot high
Vll avg high kVAR tot high
V unbal high kVA tot high
Ia high PF lag high
Ib high PF lead high
Ic high Freq high
Hist Mean Log
Vll ab mean I avg mean
Vll bc mean I 4 mean

Vll ca mean kW tot mean
Vll avg mean kVAR tot mean
V unbal mean kVA tot mean

Ia mean PF lag mean
Ib mean PF lead mean

Ic mean Freq mean
Hist Low Log
Vll ab low I avg low
Vll bc low I 4 low

Vll ca low kW tot low
Vll avg low kVAR tot low
V unbal low kVA tot low

Ia low PF lag low
Ib low PF lead low

Ic low Freq low
Loss log
The Loss Log is configured to record loss values. By default, it logs the following
values:
MU Ia^2h int Phase A interval current squared hours
MU Ib^2h int Phase B interval current squared hours
MU Ic^2h int Phase C interval current squared hours
MU Vllab^2h int Phase A interval voltage Line-to-Line squared hours
MU Vllbc^2h int Phase B interval voltage Line-to-Line squared hours
MU Vllca^2h int Phase C interval voltage Line-to-Line squared hours
7EN02-0374-00 105
MU Vln a^2h int Phase A interval voltage Line-to-Neutral squared hours
MU Vln b^2h int Phase B interval voltage Line-to-Neutral squared hours
MU Vln c^2h int Phase C interval voltage Line-to-Neutral squared hours
Harmonics logs
Two harmonics logs record various harmonics data, including K-factor and Total
Harmonic Distortion (THD). These recorders are labeled Harm Mean Log and
Harm High Log. By default, they log the following values:
Harm Mean Log Harm High Log
V1 THD mean V1 THD high
I1 THD mean I1 THD high
I1 K Fac mean I1 K Fac high
Energy/demand log
The Energy/demand log records energy and demand data used by energy
management software to generate reports. Changing the logged data can prevent
the generation of reports that use this data.
Sag/swell log
The Sag/swell Log provides details of power quality events. By default, it logs the
following values:
SS1 DistDur SS1 DistV1Min SS1 DistV1Max SS1 DistV1Avg
SS1 DistV1Engy SS1 DistV2Min SS1 DistV2Max SS1 DistV2Avg
SS1 DistV2Engy SS1 DistV3Min SS1 DistV3Max SS1 DistV3Avg
SS1 DistV3Engy SS1 DistNominal SS1 Swell Lim SS1 Sag Lim
EN50160 compliance logs

The EN50160 compliance logs are used to record EN50160 compliance
parameters:
Data recorder EN50160 component logged
EN50160 Flicker Flicker

EN50160 Frq/Mg Power frequency and supply magnitude
EN50160 Hrm Vlt Harmonics

EN50160 Intrp Short/log interruptions
EN50160 Ovrvlt1 Temporary overvoltage
EN50160 Ovrvlt2 Temporary overvoltage
106 7EN02-0374-00
Data recorder EN50160 component logged
EN50160 Prm-f/V Parameter data (disabled by default)
EN50160 Prm-VIr Parameter data (disabled by default)
EN50160 Vunbal Voltage unbalance
EN50160 PrmHrm1 Parameter data (disabled by default)
EN50160 PrmHrm2 Parameter data (disabled by default)
EN50160 Vlt Dp1 Supply voltage dips
The meter logs EN50160 counter data for present and previous observation
periods as well as EN51060 events.
See the EN50160 2010 compliance and ION meters technical note, available from
www.schneider-electric.com, for more information about your meter’s EN50160
compliance.
4-30 compliance logs

Four 4-30 compliance logs are used to log parameters related to the International
Electrotechnical Commission’s IEC 61000-4-30 standards’ power quality
compliance and to create reports:
Data recorder 4-30 parameters logged
4-30 10m Log PqFlag

V1
V2
V3
V1 THD (Total Harmonic Distortion)
V2 THD
V3 THD
NegSeqComp (Vneg/Vpos)
ZeroSeqComp (Vzero/Vpos)
Power Freq
4-30 2hr Log PqFlag

V1
V2
V3
V2 THD
V3 THD
Power Freq
4-30 3s Log PqFlag

V1
V2
V3
V2 THD
V3 THD
7EN02-0374-00 107
Data recorder 4-30 parameters logged
Power Freq
4-30 10s Freq Power Frequency

PqFlag
4-30 V Intrp DrtnAll Voltage interruption duration (all voltages)
See the 4-30 Compliance and ION Meters technical note, available from
www.schneider-electric.com, for more information about your meter’s 4-30
compliance.
Event log overview

Your meter records events produced by the meter’s ION modules or external meter
events.
Meter events, such as meter configuration or changes to I/O state, have priority
values associated with them, so you can control what events are logged. Each
event has a priority based on its type and severity, and for most events you can
configure the priority. The event log records the date and time of the event, along
with relevant details about the event.
Your meter’s event log can be viewed through the meter’s display and ION Setup.
Event log data example:
NOTE: This example is representative only, and your meter’s event log may

information about the Event Log Controller module and other ION modules.
Related Topics
• Data viewing using your meter’s display
Default event log configuration

Your meter logs all configuration changes, meter access events, and power system
events.
You can configure certain features, such as the digital inputs, so an event is logged
when the feature changes state (for example, the digital input changes from off to
on).
Your meter’s event log might be used by other components of your power
monitoring system. Do not change the default event log configuration unless you
understand the impact of the change on the power monitoring system components
and the data they use and on your meter’s memory.
Changing the default event log configuration should only be undertaken by those
with an advanced understanding of ION architecture and their meter’s template.
The event log is controlled by the Event Log Controller module, which allows you to
set a priority cutoff for event logging. Events with a priority number greater than the
cutoff value are logged, and events with lower priorities are discarded. By default,
this value is set so that all relevant events are recorded in the meter’s event log.
Event priority values range from 0 to 255 with a typical cutoff value of 5.
108 7EN02-0374-00
NOTE: Alarms are generated by events from certain ION modules. The alarm level
is determined by the priority of the associated event. To disable the alarm but still
record the associated event, set the alarm priority to info only. To disable the alarm
and the event, set the alarm priority to none.
information about the Event Log Controller module and event priorities for specific
ION modules.
Related Topics
• Alarms overview
Waveform recording overview

Your meter is able to record voltage and current waveform information.
Waveform information is used to help identify power system disturbances, which
are an increasing concern for industrial plants, hospitals, data centers and other
facilities where the equipment is sensitive to voltage or current sags, swells, and
momentary interruptions. Waveform information is also used to help ensure
compliance with power quality standards.
In addition to measuring and recording numerical values for voltage and current,
your meter can also capture the sinusoidal waveform data. The current and voltage
waveform data provides additional information for analysis of the system’s power
quality or a power quality event.
You can manually trigger waveform recordings or configure them to trigger
automatically when there is a power quality or power system event. For waveform
recording to trigger automatically, you must enter your system’s nominal (normal)
voltage and current values, and then the amount of deviation from the nominal
required to trigger waveform recording.
Your meter’s waveform data storage format is defined by:
• Cycles: the number of cycles (based on your power system’s frequency)
included in the waveform (its duration).
• Samples: samples per cycle, which is the number of waveform data points
collected in each cycle.
This gives you the option to record a lot of information for a very short duration or
less information over a longer duration. You can also configure a delay in starting
waveform recording which allows you to record pre- and post-event data.
You can use your meter to detect ITI (CBEMA) - type disturbances, and can
determine information regarding the magnitude and duration of each disturbance.
This information can be used by your energy management system to plot the
disturbance on a CBEMA curve.
COMTRADE waveform data is available from your meter.
NOTE: If you are generating COMTRADE waveform information, the associated
waveform recorders cannot be modified unless COMTRADE is disabled. If the
waveform recorders are not configured identically, COMTRADE waveform
information will not be generated.
Key terms
Term Definition
COMTRADE COMmon format for TRAnsient Data Exchange (COMTRADE) is a common
format for waveform data.
ITI (CBEMA) A curve that graphically describes an AC input voltage envelope which can be
typically tolerated by information technology equipment. Meter waveform
information is plotted on this curve to help evaluate power quality.
Nominal The normal or usual parameter value. For example, the nominal voltage for
many power systems is 120 V.
7EN02-0374-00 109
Term Definition
Sag A power event where the voltage or current drops below the nominal value.
Swell A power event where the voltage or current rises above the nominal value.

information on the Waveform Recorder module and its settings.
Related Topics
• Setpoint learning overview
• COMTRADE
Default waveform recording configuration

Your meter’s waveform recording operates once your nominal values are
configured.
Your meter has the following default waveform recorders:
Waveform recorder Description
Wfm Rc V1-Sg/Sw V1 voltage waveforms recorded during a defined sag or swell event.
Wfm Rc I1-Sg/Sw I1 current waveforms recorded during a defined sag or swell event.
Configuring waveform recording using ION Setup

You can configure waveform recording using ION Setup.
For waveform recording to trigger automatically, you must enter your system’s
nominal (normal) voltage and current values, and then the amount of deviation
from the nominal required to trigger waveform recording.
Changing your meter’s waveform recording configuration clears your meter’s
existing waveform records.
NOTICE
DATA LOSS
Ensure that all important data has been recorded before configuring waveform
recording.
1. Start ION Setup.

3. Navigate to Alarming and click the Sag/Swell tab. Configure your meter’s sag/
swell detection parameters.
110 7EN02-0374-00
4. Navigate to Power Quality and click the Sag/Swell tab to configure your
meter’s waveform recording parameters.
NOTE: COMTRADE status must be set to Disabled before modifying the
waveform format.
Sag/swell detection parameters
Parameter Values/Range Description
Nominal voltage 0 - 999,999 Specifies the nominal voltage value used for sag/swell
detection.
Voltage Swell % Percentage of Specifies how much a measured value must exceed the
nominal nominal in order to be considered a swell.
Voltage Sag % Percentage of Specifies how much a measure value must fall below the
nominal nominal in order to be considered a sag.
Nominal current 0 - 999,999 Specifies the nominal current used by Swell and Sag
limit % for a current sag or a current swell.
Current Sag Numeric value Specifies the percentage the current must deviate from
Pickup the nominal current in order to be classified as a sag.
Current Sag Numeric value Specifies the additional amount that the current must
Dropoff recover in order to signal the end of the sag.
Current Swell Numeric value Specifies the percentage the current must deviate from
Pickup the nominal current in order to be classified as a swell.
Current Swell Numeric value Specifies the additional amount that the current must
Dropout recover in order to signal the end of the event.
Waveform recording parameters
Sag/Swell depth Specifies the number of records the sag/swell data log can hold.
Waveform depth Specifies the maximum number of waveform records stored on the meter.
Waveform Specifies the number of samples per cycle and the number of cycles that are
format stored in a waveform record.
Post event Specifies the number of cycles recorded after the waveform is triggered.
cycles
NOTE: The maximum number of post event cycles cannot exceed the
number of cycles in the waveform record.
Hysteresis % Specifies the difference in magnitude between the start and end thresholds
for a power quality event.
Setpoint learning overview

Your meter can learn acceptable ranges or thresholds by monitoring normal
operating values to determine what constitutes a voltage sag or swell in order to
help identify high and low setpoints.
NOTE: To help your meter learn the most accurate values possible, it is important
that learning occur during a period of normal operation. Do not schedule learning
during a period of unusual operations in your system. Do not modify your meter’s
configuration during the learning period as it may stop the learning process.
You can configure the meter so that learned values are applied automatically once
the learning period is complete or require that they are reviewed and manually
applied. If a learned value is invalid, the learned values are not automatically
applied, but logged for review.
Setpoint learning can be used to identify the following values:
7EN02-0374-00 111
Feature Values
Setpoints (Alarms) High limit
Low limit
Sustain until ON
Sustain until OFF
Sag Voltage sag limit
Swell Voltage swell limit
Learning installation mode and learning duration

You can configure learning for manual or automatic mode.
There are two learning installation modes:
• Manual: the meter learns the applicable values but does not begin using the
learned values. The learned values are recorded for review, and you can decide
to use the learned values or adjust them as required before manually
implementing the learned values.
• Automatic: the meter learns the applicable values and begins using those
learned values automatically at the end of the learning period. If a learned value
is invalid, the meter does not apply the value, but the value is recorded in the
event log.
You can configure the maximum learning duration. The actual learning duration
may vary, depending on the stability of the system. If the system is stable for a
period equal to one quarter of the maximum learning duration, learning is
complete; otherwise, the learning period will be the maximum learning duration.
Example: Setpoint learning duration in a stable system

In this example, the learning duration is 30 days. When the system is stable for 7.5
days (one quarter of 30 days) learning is complete.
115%
Le a rne d s we ll limit = 110%
P e rce nta ge of nomina l
110%
105%
100%
95%
90% Le a rne d s a g limit = 87%
85%
Maximum duration remaining
Stable learning time
Example: Setpoint learning duration in an unstable system

In this example, the learning duration is 30 days. Because the system is not stable
for 7.5 days (one quarter of the 30 days) learning is complete at the end of the
maximum learning duration.
112 7EN02-0374-00
Lea rne d s we ll limit = 115%

115%
P e rce nta ge of nomina l

110%
105%
100%
95%
90% Lea rne d s a g limit = 87%
85%
Maximum d ura tion remainin g
Stab le lear ning time

information on Sag/Swell, Setpoint and Relative Setpoint modules.
Related Topics
• Implementing sag/swell limit learning using ION Setup
• Implementing alarm setpoint learning using ION Setup
7EN02-0374-00 113
PowerLogic™ ION7400 series Inputs / outputs
Inputs / outputs
I/O Overview
Your meter has onboard digital I/O which can be increased by adding optional
digital and analog I/O modules to expand your meter’s I/O capabilities.
Your meter base has:
• 3 digital inputs
• 1 form A digital output
• 2 energy pulsing LEDs (one visible, one infrared)
Your meter’s integrated display has:
• kWh energy pulsing LEDs (one visible, one infrared)
• kVARh energy pulsing LEDs (one visible, one infrared)
• an optical port that can be used for energy pulsing
You can view information about your meter’s I/O through the display and
webpages, and configure your meter’s I/O using ION Setup.
Input/output ION modules

ION modules are used to configure your meter’s digital or analog inputs/outputs (I/
O).
You need to configure the following ION modules in order to use the meter’s digital
or analog I/O.
• Digital input: uses the Digital Input module, which tells the meter how to
interpret incoming signals.
• Digital output: uses one of three ION modules depending on the application.
◦ Digital Output module: monitors a change of state to control relay operation
via a hardware output device.
◦ Pulser module: transfers high-speed pulses to a hardware pulse counting
device that is used to track energy usage.
◦ Calibration Pulser module: integrates instantaneous power inputs, then
outputs high-speed pulses to an LED that can be monitored for energy
accuracy verification.
NOTE: All of these modules can act as intermediaries between the physical
hardware port and the other modules in the meter. They define the
characteristics of the outgoing signals.
• Analog input: uses the Analog Input module, which tells the meter how to
interpret an incoming analog voltage or current signal from transducers.
• Analog output: uses the Analog Output module to deliver a continuous direct
voltage or current analog signal to transducers.
Input/output ION modules, ports and labels

You can configure the Digital Output, Digital Input, Analog Input, Analog Output,
Pulser and Calibration Pulser ION modules to specify which port handles the
outgoing or incoming signals.
To assign a port to one of these modules, simply modify the Port setup register by
picking a port from the enumerated list.
The following tables describe the ports that can be configured to handle outgoing
or incoming signals.
114 7EN02-0374-00
Inputs / outputs PowerLogic™ ION7400 series
Onboard input and output ports
ION module ION module Hardware port Port name (ION Description
type name (device label) label)
Digital Output Port D1 D1 Port D1 Form A output
Calibration Top LED N/A Top LED Watt energy

Pulser pulsing
(located on meter
body)
WATT LED WATT WATT LED Watt energy

pulsing
(located on
integrated
display)
VAR LED VAR VAR LED VAR energy

pulsing
(located on
integrated
display)
Optical Port Optical port Optical Port LED Watt energy

pulsing
(located on
integrated
display)
Port S1 S1 Port S1 Externally excited
Digital Input Port S2 S2 Port S2 Externally excited
Port S3 S3 Port S3 Externally excited
Option module(s) input and output ports
ION module ION module Hardware port Port name (ION Description
type name (device label) label)
Digital Input Port A/B/C/D-S1- S1 - S6 Port A S1 - S6 Option module

S6 digital inputs
Port B S1 - S6
Port C S1 - S6
Port D S1 - S6
Digital Output Port A/B/C/D D1 - Relay 1 - Relay 2 Port A D1 - D2 Option module
D2 Port B D1 - D2 digital output
Port C D1 - D2
Port D D1 - D2
Analog Input Port A/B/C/D A1 - A1 - A4 Port A A1 - A4 Option module
A4 Port B A1 - A4 analog input
Port C A1 - A4
Port D A1 - A4
Analog Output Port A/B/C/D Q1 S1 - S6 Port A Q1 - Q2 Option module
- Q2 analog output
Port B Q1 - Q2
Port C Q1 - Q2
Port D Q1 - Q2
NOTE: When configuring your meter, the configuration interface may show all of
the possible ports, regardless of what is physically available on your meter.
See the ION Reference, available from www.schneider-electric.com for more
information about ION modules.
7EN02-0374-00 115
Related Topics
• Option modules overview
I/O option modules

I/O option modules provide increased digital and analog input/output (I/O)
capabilities for your meter.
WARNING
Do not use the meter for critical control or protection applications where human
equipment damage.
These I/O modules can be used to monitor the status of breakers, control analog or
digital transducers, or receive signals that can be interpreted to provide WAGES
data for your energy system. For applications requiring high accuracy, such as
energy pulsing to verify accuracy, the digital output on the meter base is
recommended.
upgrade. Option modules are offline during an option module firmware upgrade;
Your meter’s analog I/O option modules can measure and output either low voltage
or current using standard analog transducers such as 4 - 20 mA current
transducers.
Analog I/O option module data viewing

View analog I/O option module data from the webpages and display.
To view analog option module data on your meter’s display, go to Inputs/Outputs
and select either Analog Inputs or Analog Outputs. If there are no I/O of the
specified type, an informative message is displayed.
To view analog option module data on your meter’s webpages, connect to your
meter’s webpages, go to Monitoring > Inputs/Outputs and select either Analog
Inputs or Analog Outputs. If there are no I/O of the specified type, an informative
message is displayed.
Digital I/O option module data viewing

View digital I/O option module data from the webpages and display.
To view digital option module data on your meter’s display, go to Inputs/Outputs
and select either Digital Inputs or Digital Outputs. If there are no I/O of the
specified type, an informative message is displayed.
To view digital option module data on your meter’s webpages, connect to your
meter’s webpages, go to Monitoring > Inputs/Outputs and select either Digital
Inputs or Digital Outputs. If there are no I/O of the specified type, an informative
message is displayed.
116 7EN02-0374-00
Analog inputs
Analog input applications
You can use an analog input to monitor an analog flowmeter to monitor how much
water flows through a pipe.
For analog input operation, your meter takes an analog input signal and provides
the resulting scaled value.
Your meter’s analog I/O option modules can measure either low voltage or current
using standard analog transducers such as 4 - 20 mA current transducers.
Related Topics
• Specifications
Analog input voltage and current mode

You can set the analog input’s mode for voltage or current sensing.
In current mode, the analog inputs have a low input resistance while the meter is
powered on, and a high input resistance when the meter is powered off. In voltage
mode, the analog inputs have a high input resistance regardless of whether the
meter is powered or not.
NOTE: When unpowered, your meter’s analog inputs act like they are in voltage
mode (high input resistance).
When connected to a current output transducer, this high resistance can create a
high voltage. Standard (i.e., 4 to 20 mA) current transducers have open circuit
protection and are able to handle a high input resistance; however, if non-standard
transducers are used high voltages may be generated. Your meter’s analog input
has circuitry to limit this voltage, but it may not be sufficient with a very high-power
current source.
NOTICE
EQUIPMENT DAMAGE
• Ensure the analog input is configured for the correct voltage or current mode
before connecting or activating the current transducer.
Failure to follow these instructions will result in equipment damage.
Related Topics
• Specifications
Analog input behavior

Analog inputs may show a value below zero scale if an open circuit is detected on
the input port.
Analog input zero scale and full scale values

Configure your analog input’s zero and full scale values.
In most cases the output range of the sensor feeding the analog input matches the
hardware limits of your meter’s analog input port. In that case, the analog input’s
zero scale and full scale values are the same as the sensor’s represented range.
For example:
7EN02-0374-00 117
Analog sensor Meter’s analog input Analog input values
0 - 50 psi represented by a 4 - 20 mA analog input range Full scale = 50 (psi)

4 - 20 mA signal Zero scale = 0 (psi)
If the sensor’s output range does not match your meter’s hardware limits, you must
calculate the full scale and/or zero scale values by analyzing the system.
information about the Analog Input module and full scale and zero scale
calculations.
Configuring option module analog inputs using ION Setup

You can configure analog inputs using ION Setup.
Analog inputs are available on the optional I/O modules you can connect to the
base of your meter.
Calculate your zero scale and full scale values based on the analog source and the
input range of your meter.
Make sure that the analog input port that you want to use is properly configured
and connected to a valid external analog signal source.
1. Start ION Setup.

3. Navigate to Expansion Module > Option I/O Modules and select the module
tab that corresponds to the option module with the analog input you want to
configure.
4. Select the analog input channel and click Edit. The setup screen for that analog
input is displayed.
5. Configure the analog input by selecting the parameter and clicking Edit.
Parameter Value/Range Description
Zero scale 0 to ±109 The minimum source value that matches the minimum
analog input signal.
Full scale 0 to ±109 The maximum source value that matches the maximum
analog input signal.
Port – The physical analog input port connection.
Mode Voltage, current Determines whether the analog input is monitoring

voltage or current.
Analog outputs
Analog output applications
You can use an analog output to send a signal to an analog-controlled valve to
modify a water pipe’s valve position in order to change the flow rate.
For analog output operation, your meter takes an input value and scales it to the
appropriate signal value to send out the physical analog output port.
Your meter’s analog I/O option modules can output either low voltage or current
using standard analog transducers such as 4 - 20 mA current transducers.
118 7EN02-0374-00
Related Topics
• Specifications
Analog output behavior

Your meter’s analog output, once configured, outputs voltage or current signals. If
your meter’s analog output source becomes unavailable (N/A) the analog output
level should go to zero (0 V / 0 mA) under most conditions.
When your meter is powered off or configured to send voltage, the meter registers
as a high impedance.
The electrical signal on the analog output is DC; make sure proper polarity is
observed when wiring external devices to the analog output ports.
An unexpected change of state of the analog outputs can result when the supply
power to the meter is interrupted, during an upgrade of the meter’s firmware or
framework or option module firmware or a during an option module reset.
WARNING
equipment damage.
Analog output zero scale and full scale values

Configure your analog output’s zero and full scale values.
In most cases your meter’s analog output range matches the range of the analog
sensors that your meter’s outputs are connected to. In that case, your meter’s
analog output zero scale and full scale values are the maximum and minimum
values of the source driving your meter’s analog output. These values are used to
normalize the source value to a value between 0 and 1 which is applied to the
operating range of the analog output port to determine the analog output current or
voltage. For example:
Source value Analog output values Meter’s analog Analog sensor

output
0 to 120 kW range Full scale = 120 (kW) 4 - 20 mA range 4 - 20 mA range

100 kW Zero scale = 0 (kW) Output: 17.28 mA
Normalized: 0.83
If your meter’s analog output range does not match the range of the connected
analog sensor, you must calculate the full scale and zero scale values by analyzing
the system.
See the ION Reference, available from www.schneider-electric.com for detailed
information about the Analog Output module and full scale and zero scale
calculations.
Configuring option module analog outputs using ION Setup

You can configure option module analog outputs using ION Setup.
Analog outputs are available on the optional I/O modules you can connect to the
base of your meter.
Calculate your zero scale and full scale values based on the measured value and
the analog output range of your meter.
7EN02-0374-00 119
Make sure that the analog output port that you want to use is properly connected to
an analog receiver.
1. Start ION Setup.

tab that corresponds to the option module with the analog output you want to
configure.
4. Select the analog output channel and click Edit. The setup screen for that
analog output is displayed.
5. Configure the analog output by selecting the parameter and clicking Edit.
Zero scale 0 to ±109 The minimum source value that matches the minimum
analog output signal.
Full scale 0 to ±109 The maximum source value that matches the maximum
analog output signal.
Port – The physical analog output port connection.
Mode Voltage, current Determines whether the analog output is monitoring

voltage or current.
Digital inputs
Digital input applications
Digital inputs are typically used for monitoring the status of contacts, such as
status contacts on circuit breakers.
They can also be used for pulse counting or input metering applications, such as
WAGES (water, air, gas, electricity, steam) monitoring, or conditional energy
applications, or IRIG-B time synchronization.
IRIG-B time synchronization

You can use a digital input to synchronize the meter time to an IRIG-B time source.
You can connect an IRIG-B time source to one of meter’s digital inputs for IRIG-B
time synchronization; for improved accuracy use the digital inputs on the meter
base. For IRIG-B time synchronization, you must configure both the meter’s digital
input and the meter’s clock.
Related Topics
• Configuring time and time synchronization using ION Setup
Configuring onboard digital inputs using ION Setup

You can use ION Setup to configure your meter’s digital inputs.
Digital inputs are available on your meter. You can add more digital inputs using
optional I/O modules.
1. Start ION Setup.

3. Navigate to I/O > Digital Inputs. The tabs correspond to each digital input.
Click on the tab for the digital input you want to edit.
4. Configure the digital input by selecting the parameter and clicking Edit.
120 7EN02-0374-00
5. Once the parameter has been configured, click OK to save the setting to the
meter.
Parameter Value/range Description
Input Mode Pulse, KYZ, A/C, Specifies how the meter processes the signal:
IRIG-B1 • Pulse: the meter counts an entire pulse
(from off-on to on-off) as one input.
• KYZ: the meter counts a transition (from
off-on or from on-off) as one input.
• A/C: the meter detects analog signals
where the ON condition is based on the
presence of an AC signal
• IRIG-B1: the meter detects an IRIG-B time
synchronization signal.
Polarity Inverting/Non-Inverting Specifies if the signal from the digital port is

inverted or not inverted.
Debounce 0.000 - 1.000 Specifies how long (in seconds) the signal
must remain in a state to be considered a valid
state change.
Port Defined by your meter’s Your meter’s physical digital input port.
hardware
1IRIG-B can only be connected to one of the digital inputs located on the meter base, not an
option module. You must also configure your meter’s clock to use IRIG-B time synchronization.
Configuring option module digital inputs using ION Setup

You can configure option module digital inputs using ION Setup.
Digital inputs are available on your meter. You can add more digital inputs using
optional I/O modules.
1. Start ION Setup.

tab that corresponds to the option module with the digital input you want to
configure.
4. Select the digital input channel and click Edit.
The setup screen for that digital input is displayed.
5. Configure the digital input by selecting the parameter and clicking Edit.
6. Once the parameter has been configured, click OK to save the setting to the
meter.
Input Mode Pulse, KYZ, A/C, Specifies how the meter processes the signal:
IRIG-B1
• Pulse: the meter counts an entire pulse (from off-on
to on-off) as one input.
• KYZ: the meter counts a transition (from off-on or
from on-off) as one input.
• A/C: the meter detects analog signals where the ON
condition is based on the presence of an AC signal.
• IRIG-B1: the meter detects an IRIG-B time
synchronization signal.
Polarity Inverting/Non- Specifies if the signal from the digital port is inverted or
Inverting not inverted.
Debounce 0.000 - 1.000 Specifies how long (in seconds) the signal must remain
in a state to be considered a valid state change.
Port Defined by your Your meter’s physical digital input port.

meter’s
hardware
1IRIG-B can only be connected to one of the digital inputs located on the meter base, not an
option module.
7EN02-0374-00 121
WAGES monitoring
WAGES monitoring allows you to record and analyze all energy sources and
utilities usage.
Your energy system may use several different types of energy. For example, you
may consume steam or compressed air for industrial processes, electricity for
lights and computers, water for cooling and natural gas for heating. WAGES
monitoring collects the usage information from all these different energy sources to
enable a more complete energy analysis.
WAGES information can help you:
• Identify losses or inefficiencies.
• Modify demand to reduce costs.
• Optimize energy source usage.
WAGES example
This example shows WAGES monitoring for a water flow meter.
You can connect your meter’s digital input to a transducer that sends a pulse for
every 15 kiloliters (4000 US Gal) of water. After configuring an input metering
channel and assigning it to the digital input, the meter is able to detect and record
the incoming pulses. An energy management system can then use the information
from the meter to perform WAGES analysis.
30
A Water flow meter (15 kL/pulse)
B Energy meter with digital input 1 assigned to input metering channel 1 and configured with unit
kL (kiloliters)
C Energy management system with WAGES analysis capabilities
Input metering
Your meter’s digital inputs can be used to count pulses from transducers and
convert the pulses to energy measurements.
Your meter’s input metering channels count pulses received from the digital inputs
assigned to that channel. The incoming pulses are used in calculating and
measuring consumption data (e.g., BTU, kWh, L, kg). Each channel must have the
following values configured to match the pulse data:
• Pulse Weight: the pulses per unit value.
• Unit Code: the unit of measure associated with the monitored value.
• Demand Code: for time-based values (such as kWh), this provides the
associated demand units (kW) for demand calculations; for other values (such
as kg), this can be configured to provide rate information (kg/h or kg/s).
• Mode: whether a pulse is based on a complete pulse or a transition.
For example, if each complete pulse represents 125 Wh, you can configure for Wh
pulsing as follows:
• Pulse Weight = pulses/Wh = 1/125 = 0.008
• Unit Code = Wh
• Demand Code = kW (this is automatically set)
• Mode = pulse
122 7EN02-0374-00
If you want to configure for kWh pulsing, you must adjust the pulse weight
calculation and unit code as follows:
• Pulse Weight = pulses/kWh = 1/0.125 = 8
• Unit Code = kWh
Configuring standard input metering using ION Setup

You can configure input metering with standard units and rates using ION Setup
When configuring your meter, the configuration interface may show all of the
possible ports, regardless of what is physically available on your meter.
NOTE: Your device’s digital input must be connected to the input metering pulse
source. Review the digital inputs assigned to applications to help you understand
your existing configuration.
1. Start ION Setup.

3. Navigate to Energy Applications > Digital Input Based.
4. Select the input metering channel you want to configure and click Edit. The
Input Metering Channel Setup screen is displayed.
5. Select Enabled to enable the input metering feature.
6. Click Select to define which digital input is the pulse source for the input
metering channel.
NOTE: It is recommended to set Assigned Input to No connection to disable
the input metering channel by removing any port associations.
7. Configure the remaining parameters as required.
8. Click OK to save your configuration.
9. Configure your meter to log the input metering data if required.
Pulse Weight Enter the value per pulse.
Units Select the measurement units associated with the pulse.
Demand Period Enter the frequency in minutes that input metering data is calculated in your
energy management system.
Rate Select the rate associated with the defined Units.
Source ID Enter a data identifier. This value is added to the input metering channel’s
data to uniquely identify the data within your energy management system.
Configuring custom input metering using ION Setup

You can configure input metering with custom units and rates using ION Setup.
NOTE: Your device’s digital input must be connected to the input metering pulse
source. Review the digital inputs assigned to applications to help you understand
your existing configuration.
1. Start ION Setup.

3. Navigate to Energy Applications > Digital Input Based.
4. Select the input metering channel you want to configure and click Edit. The
Input Metering Channel Setup screen is displayed.
7EN02-0374-00 123
5. Select Enabled to enable the input metering feature.

6. Click Select to define which digital input is the pulse source for the input
metering channel.
NOTE: It is recommended to set Assigned Input to No connection to disable
the input metering channel by removing any port associations.
7. Clear the Standard quantity checkbox. The screen changes to display custom
input metering parameters.
8. Configure the remaining parameters as required.
10.Configure your meter to log the input metering data if required.
Pulse Weight Enter the value per pulse.
Units Select the measurement units associated with the pulse.

NOTE: Include source identification information by entering “@” followed by
the source identifier.
Demand Period Enter the frequency in minutes that input metering data is calculated in your
energy management system.
Rate Select the rate associated with the defined Units.
Scaling Select the scaling value based on the relationship between Units and Rate.
Time Base Select the value and units to match the Rate.
Digital outputs
Digital output applications
Digital outputs are typically used in switching applications, for example, to provide
on/off control signals for switching capacitor banks, generators, and other external
devices and equipment.
The digital output can also be used in demand synchronization applications, where
the meter provides pulse signals to the input of another meter to control its demand
period. The digital output can also be used in energy pulsing applications, where a
receiving device determines energy usage by counting the kWh pulses coming
from the meter’s digital output port.
Related Topics
• Specifications
Configuring onboard digital outputs using ION Setup

You can use ION Setup to configure your meter’s digital outputs.
One form A digital output is available on the base of the meter. You can add more
digital outputs using optional I/O modules.
1. Start ION Setup.

3. Navigate to either onboard or expansion I/O, Digital Outputs, and select a
digital output tab.
124 7EN02-0374-00
4. Configure the digital output by selecting the parameter and clicking Edit.
Parameter Value/range Description
Source Digital/Boolean Link this input to the value that drives the state
of the digital output.
If Source is not linked, the digital output state
is driven by the Force ON, Force OFF values.
Force ON Pulse Link this input to a pulse that forces the digital
output on for the PulseWidth duration,
regardless of the Source input.
Force OFF1 Pulse Link this input to a pulse that forces the digital
output off.
Normal1 Pulse Pulsing this input will switch the driver of the
digital output from Force ON to Source.
Polarity Inverting/non-inverting Specifies if the signal to the digital port is

inverted or not inverted.
PulseWidth 0 - 2,000,000 Specifies the duration of the pulse, in seconds.
Setting this parameter to 0 sets the digital
output continuously on.
Port — The physical digital output port connection.

Only available ports are shown.
1 These parameters are only valid when pulse width is set to 0.
Configuring option module digital outputs using ION Setup

You can configure option module digital outputs using ION Setup.
One form A digital output is available on the base of the meter. You can add more
digital outputs using optional I/O modules.
1. Start ION Setup.

tab that corresponds to the option module with the digital output you want to
configure.
4. Select the digital output channel and click Edit. The setup screen for that digital
output is displayed.
5. Configure the digital output by selecting the parameter and clicking Edit.
Source Digital/Boolean Link this input to the value that drives the state of the
digital output.
If Source is not linked, the digital output state is driven by
the Force ON, Force OFF values.
Force ON Pulse Link this input to a pulse that forces the digital output on
for the PulseWidth duration, regardless of the Source
input.
Force OFF1 Pulse Link this input to a pulse that forces the digital output off.
Normal1 Pulse Pulsing this input will switch the driver of the digital
output from Force ON to Source.
Polarity Inverting/non- Specifies if the signal to the digital port is inverted or not
inverting inverted.
PulseWidth 0 - 2,000,000 Specifies the duration of the pulse, in seconds.

Setting this parameter to 0 sets the digital output
continuously on.
Port – The physical digital output port connection. Only

available ports are shown.
1 These parameters are only valid when pulse width is set to 0.
7EN02-0374-00 125
Energy pulsing
You can configure the meter’s energy pulsing LEDs, optical port or digital output for
energy pulsing applications.
When an LED or output is set to energy pulsing, the meter sends a readable pulse
or signal based on the measured energy source value. This pulse can be used for
accuracy verification or as an input to another energy monitoring system.
Default energy pulsing LED sources

Your meter’s energy pulsing LEDs have default energy source values configured
for accuracy verification testing.
LED Location Default energy pulsing source
Top LED Top of meter body kW del+rec
WATT LED Front of integrated display kW del+rec
VAR LED Front of integrated display kVAR del+rec
Optical port Front of integrated display kW del+rec
NOTE: To modify your default energy source value, go into the advanced mode of
ION Setup and modify the associated Calibration Pulser module. This is an
advanced procedure that should only be performed if you have advanced
knowledge of ION and the power system your meter is connected to.
information.
Configuring LED energy pulsing using ION Setup

You can configure your meter’s energy pulsing LEDs and your meter’s optical port
for energy pulsing using ION Setup.
1. Start ION Setup.

3. Select LED pulsing.
4. Select the tab that corresponds to the energy pulsing LED you want to
configure:
Option Description
Top LED Visible and infrared LEDs located on the top of the meter. These energy
pulsing LEDs are available on all meters (with or without integrated
display).
WATT LED Visible and infrared LEDs located on the meter’s integrated display
labeled WATT.
VAR LED Visible and infrared LEDs located on the meter’s integrated display
labeled VAR.
Optical Port Optical port located on the meter’s integrated display.
NOTE: To use your meter’s optical port for energy pulsing, you must set
the optical port’s protocol to Infrared I/O.
126 7EN02-0374-00
5. Configure the following basic parameters for your meter’s energy pulsing LEDs.
Energy pulsing LED parameters available through ION Setup
Kt The amount of source energy required to make the LED pulse.
Pulse Width The minimum time in seconds between LED pulse transitions.
NOTE: There is a minimum 50% duty cycle on all pulses.
Pulser Mode Select when the energy pulsing LEDs will pulse:
• Always: the energy pulsing LEDs are always pulsing based on their
energy source value.
• Test Only: the energy pulsing LEDs will only pulse when the meter is in
test mode.
Pulse ovrld Pulsing normally indicates that the energy pulsing LED should be operating
normally.
Pulsing suspended indicates that the energy pulsing LED is not able to pulse
quickly enough. Modify the Kt value to decrease the number of energy
pulses.
NOTE: To perform specialized configuration go into the advanced mode of ION

Setup and modify or add a new Calibration Pulser module. This is an advanced
procedure that should only be performed if you have advanced knowledge of
ION and the power system your meter is connected to.
information.
Configuring digital output energy pulsing using ION Setup

You can configure your meter’s digital output for energy pulsing using ION Setup
Ensure that the digital output port is available for energy pulsing and not
associated with another function.
NOTE: For applications where accuracy is important, use the digital output located
on the base of the meter.
1. Start ION Setup.

3. Select Energy pulsing.
7EN02-0374-00 127
4. Select an energy pulsing source tab (such as Wh Del) to configure energy

pulsing using your meter’s digital output.
Digital output energy pulsing parameters available through ION Setup
Kt The amount of energy source required to trigger the digital output. For
example, in the Wh Del tab, the Kt value would be amount of real energy
delivered (Wh Del) per pulse.
Pulse Width The minimum time in seconds between pulse transitions.

NOTE: There is a minimum 50% duty cycle on all pulses.
OutputMode Select the desired output mode:

• Pulse: the digital output sends a complete pulse when triggered.
• KYZ: the digital output makes a transition (off to on, or on to off) when
triggered.
Port Select an output port from the list. Only available output ports are shown
(ports that are not associated with another function).
(energy source) Pulsing normally indicates that the output port should be operating normally.
ovrld Pulsing suspended indicates that the output port is not able to pulse quickly
enough. Modify the Kt value to decrease the number of energy pulses.
NOTE: To perform specialized configuration go into the advanced mode of ION

Setup and modify or add a new Calibration Pulser module. This is an advanced
procedure that should only be performed if you have advanced knowledge of
ION and the power system your meter is connected to.
information.
Calculate your maximum kWh/pulse (pulse weight) value

To calculate the kWh/pulse (pulse weight) value, divide the highest kW value you
can expect by the required pulse rate.
Make sure the required pulse rate does not exceed the maximum pulse rate for the
digital output.
NOTE: To convert from kWh/pulse to pulse/kWh you must invert (take the
reciprocal) of the value. For example, 1.8 kWh/pulse becomes 0.556 pulse/kWh.
Example pulse weight calculation

For a maximum load of 1600 kW and a pulse rate of 2 pulses per second, calculate
the kWh/pulse value as follows:
1. Convert 1600 kW load into kWh/second:
(1600 kW)*(1hr) = 1600 kWh
(1600 kWh)/(3600 sec) = (X kWh)/(1sec)
X = 0.444 kWh/sec
2. Calculate the kWh required per pulse:
(0.444 kWh/sec)/(2 pulses per second) = 0.222 kWh/pulse
3. Adjust for the KY giving one pulse per 2 transitions if necessary.
(0.222 kWh/pulse)/(2) = 0.111 kWh/pulse
128 7EN02-0374-00
Alarms and alerts PowerLogic™ ION7400 series
Alarms and alerts

Alarms overview
An alarm is the meter’s means of notifying you when an alarm condition is
detected, such as an error or an event that falls outside of normal operating
conditions.
You can configure your meter to generate and display high, medium and low
priority alarms when predefined events are detected in the meter’s measured
values or operating states. Your meter also logs the alarm event information. Your
meter comes with many alarms. Some alarms are preconfigured, while others
need to be configured before your meter can generate alarms. Your meter’s default
alarms can be customized, as needed, such as changing the priority. You can
create custom alarms using the advanced features of your meter.
Alarm types
Your meter has four types of alarms.
Type Description
Setpoint Setpoint alarms define an alarm by comparing the actual value of a parameter
(standard) to a specified limit or range of values. These include measured voltage and
current values and calculated power quality values.
Some setpoint alarms use high-speed measurements for up to 1 millisecond
resolution.
Digital Digital alarms define an alarm condition based on a digital input’s on/off state.
Disturbance (sag/ Disturbance alarms define an alarm based on a measured sag or swell.
swell)
Unary Unary alarms are not configurable, and generate an alarm based on the meter’s
state, for example, the meter powering up.
Alarms have two states:

• Active: the meter detects the alarm condition is met.
• Historical: the alarm condition previously existed but the condition has since
returned to a non-alarm state.
See the ION reference, available from www.schneider-electric.com, for more
information about Setpoint, Digital Input and Sag/Swell modules.
Standard alarms
Standard alarms are setpoint-driven alarms monitor certain behaviors, events or
unwanted conditions in your electrical system.
Standard alarms have a detection rate equal to the 50/60 meter cycle, which is
nominally 1 second if the meter’s frequency setting is configured to match the
system frequency (50 or 60 Hz).
Many of the standard alarms are three-phase alarms. Alarm setpoints are
evaluated for each of the three phases individually, but the alarm is reported as a
single alarm. The alarm pickup occurs when the first phase exceeds the alarm
pickup magnitude for the pickup time delay. The alarm is active as long as any
phase remains in an alarm state. The alarm dropout occurs when the last phase
drops below the dropout magnitude for the dropout time delay.
Example of over and under setpoint (standard) alarm operation

The meter supports over and under setpoint conditions on standard alarms.
7EN02-0374-00 129
PowerLogic™ ION7400 series Alarms and alerts
A setpoint condition occurs when the magnitude of the signal being monitored
crosses the limit specified by the pickup setpoint setting and stays within that limit
for a minimum time period specified by the pickup time delay setting.
The setpoint condition ends when the magnitude of the signal being monitored
crosses the limit specified by dropout setpoint setting and stays within that limit for
a minimum time period specified by dropout time delay setting.
Over setpoint
When the value rises above the pickup setpoint setting and remains there long
enough to satisfy the pickup time delay period (ΔT1), the alarm condition is set to
ON. When the value falls below the dropout setpoint setting and remains there
long enough to satisfy the dropout time delay period (ΔT2), the alarm condition is
set to OFF.
A Pickup setpoint
B Dropout setpoint
Ma x2
Ma x1 ΔT1 Pickup time delay period (in seconds)
EV1 Start of alarm condition

∆T1
∆ T2 ΔT2 Dropout time delay (in seconds)
EV2 End of alarm condition

∆T3
ΔT3 Alarm duration (in seconds)
EV1 EV2
Max1 Maximum value recorded during pickup period
Max2 Maximum value recorded during alarm period
The meter records the date and time when the alarm event starts (EV1) and when
it ends (EV2). The meter also performs any task assigned to the event, such as
operating a digital output. The meter also records maximum values (Max1, Max2)
before, during or after the alarm period.
Under setpoint
When the value falls below the pickup setpoint setting and remains there long
enough to satisfy the pickup time delay period (ΔT1), the alarm condition is set to
ON. When the value rises above the dropout setpoint setting and remains there
long enough to satisfy the dropout time delay period (ΔT2), the alarm condition is
set to OFF.
A Pickup setpoint
∆T3 B Dropout setpoint
ΔT1 Pickup time delay period (in seconds)

∆T2
EV1 Start of alarm condition
∆ T1
ΔT2 Dropout time delay (in seconds)
Min1 EV2 End of alarm condition
Min2
ΔT3 Alarm duration (in seconds)
EV1 EV2
Min1 Maximum value recorded during pickup period
Min2 Maximum value recorded during alarm period
The meter records the date and time when the alarm event starts (EV1) and when
it ends (EV2). The meter also performs any task assigned to the event, such as
operating a digital output. The meter also records minimum values (Min1, Min2)
before, during or after the alarm period.
130 7EN02-0374-00
Disturbance (sag/swell) alarms

These alarms are triggered by voltage and current disturbances.
You must configure nominal voltage and current for these alarms to function.
For voltage disturbances, enter the percentage deviation from the nominal that
defines a sag or swell.
For current disturbances, enter the percentage deviation from the nominal that
defines the pickup and dropout points for a current sag or a current swell.
Digital alarms
These alarms are triggered when the associated digital input changes state.
You can configure the alarm to be active when the digital input is on or off,
depending on the alarm’s purpose.
For example, if you used a digital input to monitor a breaker that is always
supposed to be on, you would set the alarm to be active when the breaker has
tripped.
NOTE: To stop a digital alarm from being displayed, set the alarm priority to info
only. Disabling (force off) the digital alarm off will disable all functions of the
associated digital input.
information about the Setpoint and Relative Setpoint module, Digital Input module,
Sag/Swell module and Disturbance Analyzer modules.
Related Topics
• Configuring sag/swell alarms using ION Setup
Alarm event priorities

Your meter’s alarm priorities correspond to event priority ranges.
Alarm priority Event priority
High (red) 192 - 255
Medium (yellow) 128 - 191
Low (blue) 64 - 127
Info only (no alarm)1 1 - 63
None (no alarm or event)1 0

1 Alarms with priority of info only or none are not indicated or displayed.
Info only and none event priority

Alarms with a priority of info only or none are not shown on the meter’s display, and
do not function as alarms. If the alarm’s priority is set to info only, and the event
priority is greater than the event log cutoff value, the associated event is recorded
in the meter’s event log. If the alarm’s priority is set to none, the event priority is
automatically set to zero, and no associated event is logged in the meter’s event
log.
For events that you want to log for future reference or troubleshooting, but don’t
want alarm functions, set the alarm priority to info only.
For nuisance events that frequently occur and you have no desire to log for
reference or troubleshooting, set the alarm priority to none.
7EN02-0374-00 131
Related Topics
Alarm indicators
Your meter’s display has an alarm indicator to show you what alarm levels have
been detected (active or historic) and whether they have been acknowledged.
For active high priority alarms, the meter’s display will also flash until the alarm is
acknowledged. There is also an alarm LED to indicate the meter’s alarm condition.
Alarm Alarm icon Alarm icon flash Alarm LED Meter display
Active high Red solid bell Flash if not • Flash if not Flash if not
acknowledged acknowledged acknowledged
• Steady if
acknowledged
Active medium Yellow solid bell Flash if not • Flash if not No flash
acknowledged acknowledged
• Steady if
acknowledged
Active low Blue solid bell Flash if not • Flash if not No flash
• Steady if
acknowledged
Historic high Red outline bell Flash if not • Flash if not No flash
• Steady if
acknowledged
Historic medium Yellow outline bell Flash if not • Flash if not No flash
• Steady if
acknowledged
Historic low Blue outline bell Flash if not • Flash if not No flash
• Steady if
acknowledged
No active or Gray solid bell No flash Off No flash

unacknowledged alarms
If there are multiple active alarms, the meter displays the alarm condition
associated with the most important active alarm. If there are multiple
unacknowledged historic alarms, the meter displays the alarm condition
associated with the most important unacknowledged historic alarm.
NOTE: To stop an alarm from being displayed without impacting other metering
features, set the alarm priority to info only.
Default alarms
Your meter comes with default alarms.
NOTE: Some alarms require configuration in order to operate.
Name Priority Description
Current Sag Ph1 - 3 High Current sag alarms for phase 1, 2, 3
Current Swell Ph1 - 3 High Current swell alarms for phase 1, 2, 3
Sag/Swell High Voltage sag/swell alarm
Over I unbal Medium Over unbalanced current alarm

Over V unbal Medium Over unbalanced voltage alarm
132 7EN02-0374-00
Name Priority Description
Over THD V1 - 3 Medium Over total harmonic distortion (THD) voltage alarms
Over kW (P) sd Medium Over kW sliding demand alarm
Over I a - c, (1 -3) 4 Medium Over current alarms
V1 - V3 Setpoint Medium Voltage setpoint alarms
Freq Setpoint Medium Frequency setpoint alarm
4-30 Volt Intrp Ph1 - 3 Low 4-30 voltage interruption power quality alarms
Digital In Info only Digital input alarms

Number of alarms determined by the total number of available digital inputs
NOTE: These alarms are not displayed by default.
Alarm information
You can view information about an alarm from your meter’s display.
Only alarms with a priority of low, medium or high are displayed.
Alarm The name of the alarm (for example, Over THD V1).
Priority Low, medium or high alarm priority.
Date The date and time the alarm was triggered.
Duration The duration of the alarm (only applies to inactive alarms).
Ack The date and time when the alarm was acknowledged (only applies to
acknowledged alarms).
Value Active alarm: The maximum value detected when the alarm was triggered.
Historic alarm: The maximum value detected during the duration of the alarm.
Viewing and acknowledging alarms using the meter’s display

You can view and acknowledge alarms using your meter’s display
1. Press the home button to display your meter’s data screen menu.
2. Navigate to Alarms > Active Alarms to view and acknowledge active alarms,
or navigate to Alarms > Historic Alarms to view and acknowledge alarms that
are no longer active.
3. Use the up and down arrows to view the different alarms. Press the info button
to view details of the selected alarm.
4. To acknowledge all active or historic alarms, press the up and down arrow
button simultaneously. A green checkmark appears by the acknowledged
alarms, and the alarm indictors are updated.
Alarm configuration
Disabling alarms through your meter’s display
You can disable alarms through the meter’s display when you are performing
maintenance tasks on your system and want to prevent nuisance alarms.
NOTE: To stop an alarm from being displayed without impacting other metering
features, set the alarm priority to info only.
7EN02-0374-00 133
WARNING
INACCURATE DATA RESULTS
Confirm your alarm is properly configured.
equipment damage.
1. Navigate to Setup Menu > Alarm Setup. Press the edit button to access the
enable/disable screen. Use the up and down arrows to scroll through the
available alarms. Simultaneously press the up and down arrow to enable or
disable the highlighted alarm.
2. Press the select button to confirm your settings.
3. Complete the system maintenance tasks.
4. Enable the alarms you disabled in step 1.
Related Topics
• Meter setup using your meter’s display
Alarm setup
You can disable alarms through the display in order to prevent nuisance alarms.
Alarm setup
WARNING
INACCURATE DATA RESULTS
Do not use data displayed on the display or in software as a substitute for proper
workplace practices or equipment maintenance.
equipment damage.
Parameter1 Description
Over I unbal Over unbalanced current alarm

Over THD V1 V1 over total harmonic distortion (THD) voltage alarm
Over P sd Over kW sliding demand alarm
Over Ia Ia over current alarm

Over Ib Ib over current alarm
Over Ic Ic over current alarm
Over I4 I4 over current alarm
Over V unbal Over unbalanced voltage alarm
V1 Setpoint V1 setpoint alarm
Freq Setpoint Frequency setpoint alarm
Sag/Swell 1 Voltage sag/swell alarm
Current Sag Ph1 Current sag alarms for phase 1
134 7EN02-0374-00
Parameter1 Description
4-30 Volt Intrp Ph1 4-30 voltage interruption power quality alarm for phase 1
Current Swell Ph1 Current swell alarms for phase 1

1Any Setpoint or Relative Setpoint module with an event priority greater than the low alarm event
priority is also displayed on this screen.
You can only enable or disable alarms using the display. Alarm configuration is
done using ION Setup. Alarms with a priority less than low (info only or none) are
not displayed.
You must configure all the parameters related to the alarm for alarm functions to
operate. For example, for the Over Ia alarm to operate, you must enter the nominal
value and the conditions that define an alarm state, even if the alarm is shown as
Enabled on the Alarm Setup screen.
Configuring setpoint/standard alarms using ION Setup

You can use ION Setup to configure the standard alarm settings.
1. Start ION Setup.

3. Navigate to Alarming and click the Standard tab.
4. Select a setpoint and click Edit.
5. Enter unit password and click OK, if required.
The Setpoint Setup screen is displayed.
6. Configure the setpoint values as required.
7. Click Save to save the settings to your meter.
By Percentage By Percentage/By Value When available, specifies if the Pickup and Dropoff entries are by percentage or by
value. If the option is not available, pickup and dropoff entries are by value.
Force Off Checked/Unchecked Forcing the alarm off disables all functions of the associated input.
To stop an alarm from being displayed without affecting other meter features, set
the alarm priority to Info only.
Label String value When available, lets you modify the default label so it more clearly identifies the
alarm. Letters, numbers, underscores are permitted. Spaces are not permitted.
Pickup Numeric value Use this setting to provide a value for when the alarm turns on.
Pickup Delay Numeric value This specifies the number of seconds the digital input must be in the alarm pickup
state before the alarm turns on.
Dropout Numeric value Use this setting to provide a value for when the alarm turns off.
Dropout Delay Numeric value This specifies the number of seconds the digital input must be below the alarm
dropoff state before the alarm turns off.
Alarm Priority None, Info only, Low, Specifies the priority level of the standard alarm. To disable the alarm, set priority
Medium or High to Info only.
Custom Priority 0-255 Select custom priority to view and configure the event priority of the event
associated with the alarm. The event log cutoff value is displayed for reference;
priorities above the cutoff are stored in the meter’s event log.
7EN02-0374-00 135
Implementing alarm setpoint learning using ION Setup

You can use ION Setup to implement setpoint learning, which analyzes your power
system and recommends settings.
NOTE: Your meter’s power system must be stable in order to learn valid setpoint
values.
1. Start ION Setup.

3. Navigate to Alarming > Standard.
NOTE: You can manually configure setpoint values by selecting the setpoint
and clicking Edit.
4. Select a setpoint and click Learn.
The Global Setpoint Learning screen is displayed.
5. Select the setpoint tabs to view existing configured or learned setpoint
information.
6. Click Setup.
The Alarm Learning Setup screen is displayed.
7. Configure the learning parameters for each setpoint and click Save.
8. Click Start All to begin setpoint learning for all setpoints.
– When setpoint learning is in progress, an asterisk is displayed next to the
setpoint.
– Click Abort to stop learning for a specific setpoint. To stop all setpoint
learning, repeat for each setpoint tab.
9. Apply the learned setpoint values:
– Automatic: the setpoint values are automatically applied unless the learning
process has issues or the learned values are invalid.
– Manual: navigate to Alarming > Setpoints and click Learn. On each
setpoint tab, click Install to apply the learned values to that setpoint.
NOTE: If you click Install while learning is in progress (in either manual or
automatic installation mode), it stops the learning process and prompts you for
confirmation that you want to stop learning and install the learned values. Once
you confirm, the learned values are automatically installed or prepared for
manual installation.
Configuring sag/swell alarms using ION Setup

You can use ION Setup to configure the sag/swell alarm settings.
1. Start ION Setup.

3. Navigate to Alarming > Sag/Swell.
4. Select a parameter and click Edit.
136 7EN02-0374-00
5. Configure the parameters as required.
Nominal voltage 1 to 999,999 Specifies the nominal voltage value used for sag/swell detection.
Voltage Swell% Percentage of nominal Specifies the swell limit expressed as a percentage of the nominal voltage.
Voltage Sag% Percentage of nominal Specifies the sag limit expressed as a percentage of the nominal voltage.
Nominal Current 1 to 999,999 Specifies the nominal current value used for sag/swell detection.
I Sag Pickup Numeric value Specifies the percentage the current must deviate from the nominal current in
order to be classified as a sag.
I Sag Dropout Numeric value Specifies the additional amount that the current must recover in order to signal the
end of the sag.
I Swell Pickup Numeric value Specifies the percentage the current must deviate from the nominal current in
order to be classified as a swell.
I Swell Dropout Numeric value Specifies the additional amount that the current must recover in order to signal the
end of the swell.
Implementing sag/swell limit learning using ION Setup

You can use ION Setup to implement voltage sag/swell learning, which analyzes
your power system and recommends settings.
NOTE: Your meter’s power system must be stable in order to learn valid sag/swell
limits.
1. Start ION Setup.

3. Navigate to Alarming > Sag/Swell.
4. Select Voltage Swell % or Voltage Sag % and click Learn. The Global
Setpoint Learning screen is displayed.
NOTE: You can manually configure the limit values by selecting the parameter
and clicking Edit.
5. Click Setup. The Alarm Learning Setup screen is displayed. Configure the
learning parameters.
Click Start to begin sag/swell learning. Click Abort to stop learning.
6. Apply the learned sag/swell limits.
– Automatic: the limits are automatically applied unless there are issues with
the learning process.
– Manual: navigate to Power quality > Sag/Swell. Select the Swell limit % or
Sag limit % and click Learn. Click Install to apply the learned limits.
NOTE: If you click Install while learning is in progress (in either manual or
automatic installation mode), it stops the learning process and prompts you for
confirmation that you want to stop learning and install the learned limits. Once
you have confirmed, the learned limits are automatically installed or prepared
for manual installation.
Install mode Automatic, • Automatic: the learned values are automatically

Manual
applied.
• Manual: the learned values are stored for you to
review and enter.
Duration 1-365 Days for maximum learning duration.
Configuring digital input alarms using ION Setup

You can use ION Setup to configure the digital alarm settings.
7EN02-0374-00 137
1. Start ION Setup.

3. Navigate to Alarming > Digital Input.
4. Configure the digital input alarm settings by selecting an input and clicking Edit.
Some settings are not configurable and are grayed out.
5. Click Save to save the changes to the meter.
Input Input On/Input Off Specifies the input state/alarm behavior:

• Input On: the alarm is on when the digital input is on.
• Input Off: the alarm is on when the digital input is off.
Force Off Checked/Unchecked Forcing the alarm off disables all functions of the associated input.
To stop an alarm from being displayed without affecting digital input features, set
the alarm priority to Info only.
Label String value When available, lets you modify the default label so it more clearly identifies the
alarm. Letters, numbers, and underscores are permitted. Spaces are not
permitted.
Alarm Priority None, Info only, Low, Specifies the priority level of the digital input alarm. To disable the alarm, set
Medium or High priority to Info only.
Custom Priority 0-255 Select custom priority to view and configure the event priority of the event
associated with the alarm. The event log cutoff value is displayed for reference;
event priorities above the cutoff are stored in the meter’s event log.
Alerting
An alert is an external notification produced by the meter to indicate changes, for
example, a change of state for a digital input, or a power quality event such as a
sag or swell.
Alerts are generated when a pulse or trigger that is configured to indicate the alert
condition activates. You can configure alerts to send notification emails or
messages to your energy management system through your meter’s existing
Ethernet communications connections. You can configure alert messages as a
simple text string or you can also include device information. You can configure the
alert’s priority so that alerts are also recorded in the meter’s event log.
You can configure multiple alerts on a single meter, each having different activation
triggers, messages and/or transmission types. For instance, you can have two
alerts, one generating an email, the other sending a message to your energy
management system, but using the same trigger conditions; or you can have two
alerts with different conditions that send two unique emails to two different email
addresses. You can also generate alerts based on triggers from devices connected
to your meter.
Creating alerts is an advanced feature that requires familiarity with ION
architecture and your power system and communications network. To create an
alert, you must configure the Alert module using a configuration tool. You must also
configure your device’s communications as needed to send the alerts, such as
configuring your meter’s SMTP settings and connecting it via Ethernet to an SMTP
mail server in order to send an alert by email.
Go to www.schneider-electric.com to see the ION meter alerts technical note for
detailed information on creating and configuring alerts, and the ION Reference for
detailed information about the Alert module and its operation.
138 7EN02-0374-00
Resets PowerLogic™ ION7400 series
Resets
Meter resets
Resets allow you to clear various accumulated parameters stored on your meter or
reinitialize the meter or meter accessories.
Meter resets clear your meter’s onboard data logs and other related information.
Resets are typically performed after you make changes to the meter’s basic setup
parameters (such as frequency, VT/PT or CT settings) to clear invalid or obsolete
data in preparation for putting the meter into active service.
Option module reset

Perform an option module reset if your option modules are not communicating to
your meter.
During an option module reset, your option module may not operate normally, and
digital and analog outputs may change state.
WARNING
equipment damage.
You can reset your meter’s option module bus through the display or using ION
Setup. This power cycles all the modules attached to your meter. If you have
queued firmware updates for your option modules on your meter’s internal FTP
site, the firmware updates are performed. Your option modules do not operate
normally during an option module reset.
By default, your meter is configured so that your meter automatically performs an
option bus reset when needed to help keep the option modules operating normally.
Contact Technical Support for instructions on changing this default configuration.
Available resets
You can perform various meter resets through the meter’s display or ION Setup.
Reset Description
• Clears all the cumulative and derived quantities from the meter (including demand, peak demand,
energy and revenue parameters).
Master Reset • Clears meter event and waveform logs.
• Clears COMTRADE waveform records from the meter’s internal FTP server.
• Clears the meter’s data logs.
Clears the peak demand values logged in the meter.

Peak Demand Reset NOTE: The peak demand reset has a lockout period that sets the minimum time allowed between
consecutive resets.
Min/Max Reset Clears all accumulated maximum and minimum values stored in the meter.
Digital Input Count Reset Clears the digital input status change counters.
Harmonics Min/Max Reset Clears all accumulated maximum and minimum harmonics values stored in the meter.
Disturbance Count Reset Clears the sag/swell event counter. The sag/swell event counter counts the number of sag/swells that
have occurred since power-up or the last reset, to provide power quality information to energy
management systems.
7EN02-0374-00 139
PowerLogic™ ION7400 series Resets
Reset Description
EN50160 Reset Clears all EN50160 parameters and statistics accumulated in the meter.
Option modules reset Resets communications to the meter’s expansion modules.
Conditional energy reset Clears the conditional energy values stored in the meter.
Input metering reset Clears the input metering values stored in the meter.
Related Topics
• Peak demand
Performing meter resets using the display

You can perform meter resets from the display after entering a valid password.
Revenue-locked meters must be unlocked to perform resets that impact revenue
data.
Your meter’s digital and analog outputs may change state or may not function
during resets.
WARNING
HAZARD OF UNINTENDED OPERATION
equipment damage.
Meter resets clear the meter’s onboard data logs and other related information.
NOTICE
DATA LOSS
Ensure all important data from the device has been retrieved before performing
a reset.
1. Navigate to Setup Menu > Resets.

2. Press the edit button to access the configuration menu and use the up and
down buttons to navigate through and select the resets you want to perform.
Press the select button to perform the resets.
Related Topics
• Revenue locking
Resets
You can perform meter resets using the display.
140 7EN02-0374-00
Resets PowerLogic™ ION7400 series
Master Reset • Clears all the cumulative and derived quantities from the meter
(including demand, peak demand, energy, revenue and test
mode parameters)
• Clears meter event and waveform logs
• Clears COMTRADE waveform records from the meter’s internal
FTP server
• Clears the meter’s data logs
Peak Demand Reset Clears the peak demand values logged in the meter
Min/Max Reset Clears all accumulated maximum and minimum values stored in the
meter
Digital Input Count Reset Clears the digital input state change counters
Harmonics Min/Max Reset Clears all accumulated maximum and minimum harmonics values
stored in the meter
Disturbance Count Reset Clears the sag/swell event counter
EN50160 Reset Clears all EN50160 parameters and statistics accumulated in the
meter
Option Modules Reset Restarts all option modules attached to the meter
Performing meter resets using ION Setup

You can perform meter resets on your meter using ION Setup.
Revenue-locked meters must be unlocked to perform resets that impact revenue
data.
Meter resets clear the meter’s onboard data logs and other related information.
NOTICE
DATA LOSS
Ensure all important data from the device has been retrieved before performing
a reset.

2. Select the Verification screen.
3. Select Normal Mode and click Display.
4. Select the desired tab in the Normal Mode dialog box. Depending on the tab
selected, different resets are available.
Tab Reset available

Energy Master Reset
Rolling Demand Peak Reset

Master Reset
Volts, Amps and Power Master Reset
Conditional Energy Cnd Reset

Master Reset
Input Metering IM(n) Reset
NOTE: n is the input metering number, for example IM1.
Peak Reset
Master Reset
7EN02-0374-00 141
PowerLogic™ ION7400 series Resets
5. Click the appropriate button to perform the reset.

For some resets, the meter indicates that the reset is in progress. Do not
configure or power down your meter until it indicates that the reset is complete
or some parameters may not be completely reset.
Related Topics
• Revenue locking
142 7EN02-0374-00
Measurements PowerLogic™ ION7400 series
Measurements
Power and power factor
The sampled measurements taken at the meter’s voltage and current inputs
provide data for calculating power and power factor.
In a balanced 3-phase alternating current (AC) power system source, the AC
voltage waveforms on the current-carrying conductors are equal but offset by one-
third of a period (a phase angle shift of 120 degrees between the three voltage
waveforms).
Power factor (PF)

Power factor (PF) is the ratio of real power (P) to apparent power (S).
Power factor is provided as a number between -1 and 1 or as a percentage from
-100% to 100%, where the sign is determined by the convention.
P
P F = ---
S
An ideal, purely resistive load has no reactive components, so its power factor is
one (PF = 1, or unity power factor). Inductive or capacitive loads introduce a
reactive power (Q) component to the circuit which causes the PF to become closer
to zero.
True PF and displacement PF

The meter supports true power factor and displacement power factor values:
• True power factor includes harmonic content.
• Displacement power factor only considers the fundamental frequency.
NOTE: Unless specified, the power factor displayed by the meter is true power
factor.
Apparent, active and reactive power (PQS)

Apparent power (S) is the capacity of your measured power system to provide
active (real power, P) and reactive power (Q).
A typical AC electrical system load has both resistive and reactive (inductive or
capacitive) components. Resistive loads consume real power (P). Reactive power
(Q) is either consumed (inductive loads) or generated (capacitive loads).
7EN02-0374-00 143
PowerLogic™ ION7400 series Measurements
+Q
(+kVAR, +kVARh)
Qu a d ra n t 2 90° Qu a d ra n t 1
PF leading PF lagging
Power factor sign convention: Power factor sign convention:
IEEE = + IEEE = −
IEC = − IEC = +
Re a ctive powe r (VAR)

Importe d/de live re d
Importe d/de live re d

A)
Ap
(V
p
ar
er
en
ow
tp
tp
ow
en
er
ar
(V
p
Ap
A)
Active power (W) Active power (W)
Exported/received Imported/delivered
-P +P
(-kW, -kWh) 180 ° 0° (+kW, +kWh)
Active power (W) Active power (W)

Exported/received Imported/delivered
Exporte d/re ce ive d
Exporte d/re ce ive d

A)
Ap
(V
p
ar
er
en
ow
tp
tp
ow
en
er
ar
(V
p
Ap
A)
Qu a d ra n t 3 Qu a d ra n t 4
PF lagging PF leading
Power factor sign convention: Power factor sign convention:
IEEE = − IEEE = +
IEC = − IEC = +
270 °
-Q
(-kVAR, -kVARh)
The units for power are watts (W or kW) for real power P, vars (VAR or kVAR) for
reactive power Q, and volt-amps (VA or kVA) for apparent power S.
Positive real power P(+) flows from source to load, and negative real power P(-)
flows from the load to the power source.
Current phase shift from voltage

Electrical current can lag, lead, or be in phase with the AC voltage waveform, and
is typically associated with the type of load — inductive, capacitive or resistive.
For purely resistive loads, the current waveform is in phase with the voltage
waveform. For capacitive loads, current leads voltage. For inductive loads, current
lags voltage.
The following diagrams show how voltage and current waveforms shift based on
load type under ideal (laboratory) conditions.
Current and voltage in phase (resistive) Current leads voltage (capacitive) Current lags voltage (inductive)
144 7EN02-0374-00
Power demand
Power demand is a measure of average power consumption over a fixed time
interval.
NOTE: If not specified, references to “demand” are assumed to mean “power
demand.”
The meter measures instantaneous consumption and can calculate demand using
various methods.
Peak demand
Peak (or maximum) demand is the highest demand level recorded over the billing
period.
Power utilities generally bill commercial customers based on their peak usage
levels, called peak demand (in kW) and energy consumption (in kWh). Peak (or
maximum) demand is the highest demand level recorded over the billing period.
You can view peak demand values on your meter’s display.
Your meter calculates the average current demand and kW, kVAR and kVA
demand using sliding window demand methods. The meter supports coincident
demand values when a peak demand is detected.
Your meter’s default configuration is suitable for most applications, or you can
customize it for your specific application. You can configure the minimum time
between consecutive demand resets.
NOTE: If not specified, references to “demand” are assumed to mean “power
demand”.
Peak demand reset lockout

The demand reset lockout time sets the minimum time allowed between
consecutive demand resets; the meter ignores any attempts to reset demand that
occur within the lockout period.
The peak demand reset lockout period is user-configurable, with a default value of
25 days.
See the ION Setup online help for instructions on how to configure demand peak
and the demand reset lockout period on your meter.
information on how Sliding Window Demand modules measure and calculate
demand values.
Related Topics
• Meter resets
Sliding window demand

To calculate demand values, your meter uses the sliding window averaging (or
rolling interval) method which divides the demand interval into a set number of
subintervals of specified duration.
The demand is measured electronically based on the average load level over the
most recent set of subintervals. Sliding window demand also provides predicted
demand values.
7EN02-0374-00 145
Examples of sliding window demand

This example shows two different ways of configuring a 15-minute demand
interval:
• Single interval (also called block or timed block): the 15-minute demand interval
is defined as a single subinterval with a duration of 15 minutes.
• Sliding window (also called rolling block): the 15-minute demand interval is
defined as three subintervals with a duration of 5 minutes each. This method
offers better response time than a single interval.
Single interval (block)
Demand value is
the average for the
Calculation updates at
last completed
the end of the interval
interval
15-minute interval 15-minute inte rva l 15-min
Time
(min)
15 30 45
Sliding window (rolling block)
Calculation updates at the end Demand value is

of the subinterval (5 minutes) the average for
the last completed
interval
15-minu te inte rva l
Time
20 25 35 40
(min)
15 30 45
WAGES monitoring
WAGES monitoring allows you to record and analyze all energy sources and
utilities usage.
Your energy system may use several different types of energy. For example, you
may consume steam or compressed air for industrial processes, electricity for
lights and computers, water for cooling and natural gas for heating. WAGES
monitoring collects the usage information from all these different energy sources to
enable a more complete energy analysis.
WAGES information can help you:
• Identify losses or inefficiencies.
• Modify demand to reduce costs.
• Optimize energy source usage.
WAGES example
This example shows WAGES monitoring for a water flow meter.
You can connect your meter’s digital input to a transducer that sends a pulse for
every 15 kiloliters (4000 US Gal) of water. After configuring an input metering
channel and assigning it to the digital input, the meter is able to detect and record
the incoming pulses. An energy management system can then use the information
from the meter to perform WAGES analysis.
146 7EN02-0374-00
30
A Water flow meter (15 kL/pulse)
B Energy meter with digital input 1 assigned to input metering channel 1 and configured with unit
kL (kiloliters)
C Energy management system with WAGES analysis capabilities
Incremental energy
Incremental energy allows you to define a start time, end time, and the time interval
(increments) for incremental energy accumulation.
At the end of each interval, the energy accumulated during that period is stored. By
default, the meter only records the previous interval’s incremental energy and the
instantaneous energy accumulations in the active interval.
The first interval of incremental energy accumulation begins at the specified start
time. Incremental energy ends at the specified end time, which may result in a
truncated interval if the interval duration does not divide evenly into the overall
incremental energy duration (for example, an interval duration of three hours with
an overall duration of five hours truncates the last interval duration to two hours).
The latest value for the specified end time is midnight (24:00).
Your start time must be before the end time and after midnight, and the period over
which incremental energy is accumulated cannot include midnight. This is because
your meter’s start and end times are defined relative to midnight.
Start: 6 am, End: Incremental energy accumulates from 6 am to midnight in intervals of 3 hours.
12 am, interval: 3
hrs
Start: 6 am, End: Incremental energy will not function. End time must be after start time and
2 am, interval: 3 before or equal to midnight.
hrs
Incremental energy helps provide information for analyzing energy and power
usage against present or future utility rates, and is useful for comparing different
time-of-use rate structures.
When configuring incremental energy, shorter incremental energy periods provide
more granular data which can make the data easier to use for comparison
purposes.
Incremental energy example

• Start time: 8 am or 08:00
• End time: 12 am or 24:00
• Interval: 420 minutes (7 hours)
7EN02-0374-00 147
A First interval (08:00 to 15:00)
B Second interval (15:00 to 22:00)
C Third interval (22:00 to 24:00)
The first incremental energy interval is from 8 am (start time) to 3 pm, and is seven
hours long. The second incremental energy interval is from 3 pm to 10 pm, and is
also seven hours long. The third interval is from 10 pm to 12 am, and is only 2
hours long because 12 am is the specified end time. These intervals repeat every
24 hours until the configuration is changed or incremental energy feature is
disabled.
Configuring incremental energy using ION Setup

You can configure incremental energy using ION Setup.
1. Start ION Setup.

3. Navigate to Energy Applications > Incremental Energy.
4. Select Status and click Edit. The incremental energy configuration screen is
displayed.
NOTE: To display parameters for configuration, select Enable.
5. Select the parameter to configure and click Edit. Your changes are made to the
meter.
NOTE: Configuring any parameter resets the incremental energy values
recorded by your meter.
Parameter Range Description
Status Enable/disable Enables the incremental energy feature.
Start time 12:00 am to The incremental energy first interval’s start time. The
11:59 pm start time must be prior to the end time for energy
accumulation.
End time 12:01 am to The end time for incremental energy.
12:00 am
The end time must be after the start time and be less
than or equal to 12 am (midnight).
Interval duration Configurable The increment period for the incremental energy
duration.
Conditional energy
Conditional energy allows you to define an accumulation period for real and
reactive energy using one of your meter’s digital inputs.
You can use conditional energy to track four-quadrant accumulated energy during
a specific period; for example you may want to track accumulated energy values
during a particular process controlled using a programmable logic controller (PLC).
Conditional energy is accumulated until it is reset. The conditional energy reset
date and time information is stored in the meter’s event log.
148 7EN02-0374-00
Related Topics
• Apparent, active and reactive power (PQS)
Configuring conditional energy using ION Setup

You can enable and configure conditional energy settings using ION Setup.
One of your device’s digital inputs must be connected and configured to define
when conditional energy is accumulated.
1. Start ION Setup.

3. Navigate to Energy Applications > Digital Input Based. Review the digital
inputs assigned to applications to help ensure there are no conflicting usages.
4. Select Conditional Energy and click Edit. The Conditional Energy Setup
5. Select Enabled to enable the conditional energy feature.
6. Click Select to define the digital input. The input’s state determines whether
conditional energy is accumulated. When this digital input is on, conditional
energy is accumulated.
NOTE: It is recommended to set Assigned Input to No Connection to disable
the conditional energy feature by removing any port associations.
Trending and forecasting overview

Trending and forecasting is a feature on your device that predicts the next set of
measured or calculated data by plotting and analyzing trends in historical data.
Trending and forecasting data is a useful tool to help analyze changes in load and
power quality and forecasting values such as demand. For your meter’s trending
and forecasting feature to work, you only need to give the meter time to
accumulate data.
Trending and forecasting implementation

Data used for trending and forecasting can be logged for specific intervals.
Data used is logged for the following intervals:
• Every hour for the last 24 hours
• Every day for the last month
• Every week for the last 8 weeks
• Every month for the last 12 months
The following parameters are configured for trending and forecasting using ION
Setup:
kW sd del-rec (demand) Freq (frequency)
Vll ab I a mean
Vll bc I b mean
Vll ca I c mean
Vll avg I avg mean
7EN02-0374-00 149
You can configure the start day of the week for trending and forecasting using ION
Setup.
Viewing trending and forecasting data on your meter’s webpages

You can select data for forecasting and trending and view the resulting information
using your meter’s webpages.
For trending and forecasting to operate, your meter must have accumulated data
for at least two of the specified intervals; for example, if you want to view a daily
graph, your meter must have accumulated data for at least two previous days
before the present day.
1. Log in to your meter’s webpages

2. Click Monitoring > Trending & Forecasting
3. Select the Target and Interval. The graph for the selected data is displayed.
150 7EN02-0374-00
Power quality PowerLogic™ ION7400 series
Power quality
Power quality overview
Your meter measures voltage and current harmonics, and calculates several
harmonic distortion values as well as K-factor and crest factor values.
You must configure your meter with nominal values for voltage, current and
frequency for the power system being monitored in order for the meter to perform
power quality calculations. Your meter also creates a phasor diagram, including
numeric values for magnitude and angle, to represent your power system.
Sag/swell overview
Your meter monitors your power system’s voltage and current for sags and swells
(INCITS (CBEMA) Type 2 and Type 3 disturbances); it then reports the
disturbance’s magnitude and duration.
You can manually enter the limits (criteria) used by the meter to identify a sag or
swell, or you can have your meter learn sag/swell limits by monitoring your power
system.
Related Topics
• Waveform recording overview
• Configuring waveform recording using ION Setup
• Implementing sag/swell limit learning using ION Setup
Harmonics overview
Harmonics information is valuable for power quality analysis, determining properly
rated transformers, maintenance and troubleshooting.
Harmonics are integer multiples of the fundamental frequency of the power
system. Harmonics information is required for compliance to system power quality
standards such as EN50160 and meter power quality standards such as IEC
61000-4-30.
Harmonics measurements include per-phase magnitudes and angles (relative to
the fundamental frequency of the phase A voltage) for the fundamental and higher
harmonics relative to the fundamental frequency. The meter’s power system
setting defines which phases are present and determines how line-to-line or line-
to-neutral voltage harmonics and current harmonics are calculated.
Harmonics are used to identify whether the supplied system power meets required
power quality standards, or if non-linear loads are affecting your power system.
Power system harmonics can cause current flow on the neutral conductor, and
damage to equipment such as increased heating in electric motors. Power
conditioners or harmonic filters can be used to minimize unwanted harmonics.
Viewing harmonics information using the display

You can view detailed harmonics data through your meter’s display.
1. With your meter in alt mode, navigate to Power Quality > Harmonics.
The total harmonic distortion (THD) screens are displayed.
2. Press the more button, and select the desired harmonics.
The per-phase harmonics are graphically displayed.
7EN02-0374-00 151
PowerLogic™ ION7400 series Power quality
3. Press the left and right buttons to move to individual harmonics.

The harmonic number, magnitude and angle are displayed.
Related Topics
Voltage crest factor

Crest factor is the ratio of peak to RMS voltage values.
For a pure sinusoidal waveform, crest factor is equal to 1.414. The meter uses the
following equation to calculate crest factor:
C = Crest factor
Vpeak
C= Vpeak = Voltage peak
VRMS
VRMS = Voltage RMS
Crest factor current

Crest factor is the ratio of peak to RMS current values.
For a pure sinusoidal waveform, crest factor is equal to 1.414. The meter uses the
following equation to calculate crest factor:
C = Crest factor
Ip e a k
Cre s t fa ctor = ------------- Ipeak = Current peak
IR MS
IRMS = Current RMS
K-factor
K-factor relates the heating effect of a distorted current in a transformer to a
sinusoidal current with the same RMS magnitude — it describes a transformer’s
ability to serve non-linear loads without exceeding rated temperature rise limits.
The K-factor is equal to the sum of the squares of the harmonic currents multiplied
by the squares of the harmonic order. The meter uses the following equation to
calculate K-factor:
h
∑ (Ih x h ) 2 2
n=1
K=
h 2
∑ Ih
n=1
Where K is the K-factor, h is the harmonic order and Ih is the true RMS current of
harmonic order h.
Harmonic content calculations

Harmonic content (HC) is equal to the RMS value of all the non-fundamental
harmonic components in one phase of the power system.
The meter uses the following equation to calculate HC:
152 7EN02-0374-00
Power quality PowerLogic™ ION7400 series
HC = (H 2 )2 + (H 3 )2 + (H 4 )2 ...
TDD calculations
TDD (total demand distortion) evaluates the harmonic currents between an end
user and a power source.
The harmonic values are based on a point of common coupling (PCC), which is a
common point where each user receives power from the power source.
The meter uses the following equation to calculate TDD:
TDD = ( (HCIA) 2 + (HCIB) 2 + (HCIC) 2 ) / (ILoad) x 100

Where ILoad is equal to the maximum demand load on the power system.
thd and TDD

Your meter can be configured to provide thd (total harmonic distortion using the
total RMS value for the content rather than the fundamental content) and TDD
(total demand distortion, the harmonic current distortion against the maximum
demand of the electrical system.
thd = HC / RMS *100%
TDD = HC / DemandMax *100%
This is an advanced procedure that should only be performed by users with an
advanced knowledge of power quality, ION architecture, and the power system
being monitored.
See the ION Reference, available from www.schneider-electric.com, for details
about the Harmonics Measurement module.
Phasors
Phasors are used to represent the voltage and current relative magnitude and
angles.
The length of the lines in the phasor diagram represent the relative magnitude of
the voltages with respect to the other phase voltages, and the currents with respect
to the other phase currents. All angles are measured with respect to the Va/V1
phase. The Va/V1 phasor is fixed to the right-hand horizontal axis (positive x-axis).
Positive angles are measured counterclockwise.
Numeric values are provided for the magnitude and relative angle for each voltage
and current phase.
Phasor information can be used to troubleshoot incorrect connections on the
meter’s voltage and current inputs (for example, switched phase wiring or polarity
errors), if you know how the phasors should be oriented for your power system.
Disturbance direction detection overview

Your meter has disturbance direction detection capabilities to help you determine
the location of a power system disturbance.
When a disturbance occurs, the meter analyzes the disturbance information to
determine the direction of the disturbance relative to the meter. This analysis
includes a confidence level indicating the level of certainty that the disturbance is in
the determined direction, and is stored in your meter’s event log.
7EN02-0374-00 153
PowerLogic™ ION7400 series Power quality
Disturbance direction detection is enabled on your meter by default and does not
require any additional configuration beyond setting the nominal voltage and
nominal frequency.
Disturbance direction detection can help locate the source of a disturbance when
used in a system of disturbance direction detection devices, as shown in the
diagram below.
A Disturbance location
Utility
B Meter #1 reports downstream
disturbance
C Meter #2 reports upstream
disturbance
D Meters report upstream disturbance
E Meter reports downstream

disturbance
Meter #1
Meter #2
Power consu me r
The arrows show the direction the meters have determined for the disturbance.
With this information, you can determine that the disturbance occurred between
meter #1 and meter #2, and can focus on that section of your system to find the
cause of the disturbance.
Disturbance direction detection events information

The results of the disturbance direction detection algorithm appear in the meter’s
event log.
The image below shows an example of how the Disturbance Direction Detection
event appears in your meter’s event log when viewed using ION Setup.
NOTE: You can view your meter’s event log through the display and ION Setup.

detailed information about the Disturbance Direction Detection module.
Related Topics
154 7EN02-0374-00
Verifying accuracy PowerLogic™ ION7400 series
Verifying accuracy
Overview of meter accuracy
All meters are tested and verified at the factory in accordance with International
Electrotechnical Commission (IEC) and American National Standards Institute
(ANSI) standards.
Your digital power meter typically does not require re-calibration. However, in some
installations a final accuracy verification of the meters is required, especially if the
meters will be used for revenue or billing applications.
Accuracy test requirements

The most common method for testing meter accuracy is to apply test voltages and
currents from a stable power source and compare the meter’s readings with
readings from a reference device or energy standard.
Signal and power source

The meter maintains its accuracy during voltage and current signal source
variations but its energy pulsing output needs a stable test signal to help produce
accurate test pulses. The meter’s energy pulsing mechanism needs approximately
10 seconds to stabilize after every source adjustment.
The meter must be connected to control power in order to conduct accuracy
verification testing. Refer to your meter’s installation documentation for power
supply specifications.
DANGER
Verify the device’s power source meets the specifications for your device’s
power supply.
Control equipment
Control equipment is required for counting and timing the pulse outputs from an
energy pulsing LED or digital output.
• Most standard test benches have an arm equipped with optical sensors to
detect LED pulses (the photodiode circuitry converts detected light into a
voltage signal).
• The reference device or energy standard typically has digital inputs that can
detect and count pulses coming from an external source (i.e., the meter’s digital
output).
NOTE: The optical sensors on the test bench can be disrupted by strong sources
of ambient light (such as camera flashes, florescent tubes, sunlight reflections,
floodlights, etc.). This can cause test errors. Use a hood, if necessary, to block out
ambient light.
Environment
The meter should be tested at the same temperature as the testing equipment.
The ideal temperature is about 23 ºC (73 ºF). Make sure the meter is warmed up
sufficiently before testing.
7EN02-0374-00 155
PowerLogic™ ION7400 series Verifying accuracy
A warm-up time of 30 minutes is recommended before beginning energy accuracy

verification testing. At the factory, the meters are warmed up to their typical
operating temperature before calibration to help ensure that the meters will reach
their optimal accuracy at operating temperature.
Most high precision electronic equipment requires a warm up time before it
reaches its specified performance levels. Energy meter standards allow the
manufacturers to specify meter accuracy derating due to ambient temperature
changes and self-heating.
Your meter complies with and meets the requirements of these energy metering
standards.
For a list of accuracy standards that your meter complies to, contact your local
Schneider Electric representative or download the meter brochure from
Reference device or energy standard

To help ensure the accuracy of the test, it is recommended that you use a
reference device or reference energy standard with a specified accuracy that is 6
to 10 times more accurate than the meter under test. Before you start testing, the
reference device or energy standard should be warmed up as recommended by its
manufacturer.
NOTE: Verify the accuracy and precision of all measurement equipment used in
accuracy testing (for example, voltmeters, ammeters, power factor meters).
Energy pulsing
Your meter has energy pulsing LEDs and a digital output that can be used for
energy pulsing.
Your meter has energy pulsing LEDs, one visible light and one infrared. These
LEDs emit pulses that are then used to determine the accuracy of the meter’s
energy measurements. The pulses of light indicate accumulated energy; the
meter’s accumulations are compared with the reference/standard’s accumulated
energy in order to help determine the meter’s accuracy.
Your meter also has a digital output that can be used for energy pulsing. The relay
closes (low impedance) and then opens (high impedance) to represent a pulse. If
the accuracy testing equipment has a voltage requirement, a current-limited
wetting supply voltage must be provided.
NOTE: Digital outputs on option modules should not be used meter accuracy
testing.
Related Topics
• LED locations
Verifying accuracy test meter settings

Your meter‘s power system and other parameters must be configured for accuracy
testing.
Meter parameter Value
Volts mode 4W-Wye (4 wire Wye)
PT/CT correction Disabled

Test mode Active
NOTE: In test mode, your meter’s billing
quantities stop accumulating, and the data is
sent to special test mode registers. These
registers are cleared when you exit test mode.
156 7EN02-0374-00
Verifying accuracy test

The following tests are guidelines for accuracy testing your meter; your meter shop
may have specific testing methods.
DANGER
local standards.
is off.
• Verify the device’s power source meets the specifications for your device’s
power supply.
1. Turn off all power supplying this device and the equipment in which it is installed
before working on the device or equipment.
2. Use a properly rated voltage sensing device to confirm that all power is off.
3. Connect the test voltage and current source to the reference device or energy
standard. Ensure all voltage inputs to the meter under test are connected in
parallel and all current inputs are connected in series.
I1 I2 I3
V1 V2 V3 VN
+ - + - + -
I1 I2 I3
V1 V2 V3 VN
+ - + - + -
I1 I2 I3
+ - + - + -
V1 V2 V3 VN
A Reference device or energy standard
B Test voltage and current source
C Meter under test
4. Connect the control equipment used for counting the standard output pulses
using one of these methods:
Option Description
Energy pulsing LED Align the red light sensor on the standard test bench armature over the
energy pulsing LED.
Digital output Connect the meter’s digital output to the standard test bench pulse
counting connections.
NOTE: When selecting which method to use, be aware that energy pulsing
LEDs and digital outputs have different pulse rate limits.
7EN02-0374-00 157
PowerLogic™ ION7400 series Verifying accuracy
5. Before performing the verification test, let the test equipment power up the
meter and apply voltage for at least 30 seconds. This helps stabilize the internal
circuitry of the meter.
6. Configure the meter’s parameters for verifying accuracy testing.
7. Depending on the method selected for counting the energy pulses, configure
the meter’s energy pulsing LED or one of the digital outputs to perform energy
pulsing. Set the meter’s energy pulse constant so it is in sync with the reference
test equipment.
8. Perform accuracy verification on the test points. Run each test point for at least
30 seconds to allow the test bench equipment to read an adequate number of
pulses. Allow 10 seconds of dwell time between test points.
Calculate the number of required pulses

The reference test equipment typically requires you to specify the number of
pulses required for a test duration of “t” seconds.
Normally, the number of pulses required is at least 25 pulses, and the test duration
is greater than 30 seconds.
Use the following formula to calculate the required number of pulses:
Ne Number of metering elements used
V Test point voltage in line-to-neutral volts (V) per phase
I Test point current in amps (A) per phase
t Test duration in seconds (s) which must be longer than 30 seconds
PF Power factor
Kt Pulse constant programmed in the meter under test in Wh/pulse
Round up the result of the calculation to the nearest integer number of pulses.
Calculation for number of required pulses

This example calculates the number of pulses required for an inductive load 3-
phase test point with a test duration of 60s; the source is configured to use V =
120V, I = 5A, PF = -0.5; the pulse constant of the meter under test is Kt = 1.8 Wh/
pulse.
Round the number up to the nearest integer: Number of pulses = 9
Percentage error calculation for accuracy verification testing

Accuracy verification testing requires you to calculate the percentage error
between the meter being tested and the reference/standard.
Calculate the percentage error for every test point using the following formula:
Energy error = (EM - ES) / ES x 100%
Where:
158 7EN02-0374-00
• EM = energy measured by the meter under test

• ES = energy measured by the reference device or energy standard.
NOTE: If accuracy verification reveals inaccuracies in your meter, they may be
caused by typical sources of test errors. If there are no sources of test errors
present, please contact your local Schneider Electric representative.
Typical sources of test errors

If you see excessive errors during accuracy testing, examine your test setup and
test procedures to eliminate typical sources of measurement errors.
Typical sources of accuracy verification testing errors include:
• Loose connections of voltage or current circuits, often caused by worn-out
contacts or terminals. Inspect terminals of test equipment, cables, test harness
and the meter under test.
• Meter ambient temperature is significantly different than 23 °C (73 °F).
• Floating (ungrounded) neutral voltage terminal in any configuration with
unbalanced phase voltages.
• Inadequate meter control power, resulting in the meter resetting during the test
procedure.
• Ambient light interference or sensitivity issues with the optical sensor.
• Unstable power source causing energy pulsing fluctuations.
• Incorrect test setup: not all phases connected to the reference device or the
energy standard. All phases connected to the meter under test should also be
connected to the reference meter/standard.
• Moisture (condensing humidity), debris or pollution present in the meter under
test.
Accuracy verification test points

The meter should be tested at full and light loads and at lagging (inductive) power
factors to help ensure testing over the entire range of the meter.
The test amperage and voltage input rating are labeled on the meter. Refer to the
installation sheet or data sheet for your meter’s nominal current, voltage and
frequency specifications.
Watt-hour test point Sample accuracy verification test point
Full load 100% to 200% of the nominal current, 100% of the nominal voltage and
nominal frequency at unity power factor or one (1).
Light load 10% of the nominal current, 100% of the nominal voltage and nominal
frequency at unity power factor or one (1).
Inductive load (lagging 100% of the nominal current, 100% of the nominal voltage and nominal
power factor) frequency at 0.50 lagging power factor (current lagging voltage by 60°
phase angle).
VAR-hour test point Sample accuracy verification test point
Full load 100% to 200% of the nominal current, 100% of the nominal voltage and
nominal frequency at zero power factor (current lagging voltage by 90°
phase angle).
Light load 10% of the nominal current, 100% of the nominal voltage and nominal
frequency at zero power factor (current lagging voltage by 90° phase
angle).
Inductive load (lagging 100% of the nominal current, 100% of the nominal voltage and nominal
power factor) frequency at 0.87 lagging power factor (current lagging voltage by 30°
phase angle).
7EN02-0374-00 159
PowerLogic™ ION7400 series Revenue
Revenue
Revenue locking
Revenue locking your meter helps prevent modifications to revenue-related
settings and data on your meter, or tampering with your meter’s voltage and
current connections.
Revenue locking may be required to help meet government regulations and utility
security requirements, or can be used to help ensure the validity of revenue data.
Download the ION Device Template Reference, available from
www.schneider-electric.com to view a complete listing of revenue-locked
parameters and data.
See the meter’s catalog pages, available from www.schneider-electric.com, or
consult your local Schneider Electric representative for information about your
device, its options and accessories.
Related Topics
• Revenue lock LED behavior
Revenue lock switch

You can revenue lock your meter using the revenue lock switch located on the
meter base.
This switch is accessed through a sealable cover.
A Revenue lock switch cover

B Sealing point
C Revenue LED
Revenue locking your meter

You can lock and unlock your meter using the revenue lock switch located on the
meter base.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH
local standards.
is off.
160 7EN02-0374-00
Revenue PowerLogic™ ION7400 series
1. Turn off all power supplying this device and the equipment in which it is installed
before working on the device or equipment.
2. Always use a properly rated voltage sensing device to confirm that all power is
off.
3. Open the revenue lock switch cover.
4. Locate the revenue lock switch.
5. Toggle revenue lock switch on or off.
6. Close the revenue lock switch cover and make sure it is firmly in place.
7. Seal the revenue lock switch cover if required.
PT/CT correction
PT/CT correction, also called instrument transformer correction, can help reduce
the need to replace transformers in installations where high accuracy is required.
The primary application for PT/CT (potential transformer / current transformer)
correction is to apply correction factors for ratio errors and phase angle errors to
instrument transformers. PT/CT correction is done for each current and voltage
input to the meter and only affects 1-second power meter data and values derived
from it, such as energy or demand. No high-speed, harmonics or waveform values
are affected by the correction.
NOTE: For those familiar with ION architecture, the relevant 1-second Power
Meter module outputs are compensated using the Instr Xformer (ITC) Correction
module, and therefore so are all other modules that use that Power Meter module’s
data.
instructions on how to configure PT/CT correction on your device.
information about the Instr Xformer Correction (ITC) module and how it applies PT/
CT correction to your device.
Transformer line loss compensation

Transformer Loss Compensation (TLC) is the method for compensating for the
measurable losses that occur when there is a physical separation between the
meter and the actual billing point.
Transformer Loss Compensation (TLC) is used when a meter’s actual location is
different from the electrical location where change of ownership occurs; for
example, where meters are connected on the low-voltage side of power
transformers when the ownership change occurs on the high-side of the
transformer. Meters are usually installed on the low-voltage side of a transformer
because it is more cost-effective. There are also cases where change of ownership
can occur halfway along a transmission line where it is impractical to install a
meter. In this case, power metering must again be compensated.
NOTE: Due to the variation in installations, advanced knowledge of power systems
and connection methods is required before transformer loss compensation can be
properly implemented. Data parameters should only be programmed by qualified
personnel that have appropriate training and experience with Transformer Loss
Compensation calculations.
See the Transformer Line Loss Calculations technical note available from
7EN02-0374-00 161
PowerLogic™ ION7400 series Revenue
Time of use
Time of use (TOU) is often used when a utility has set up schedules with different
rates based on time of day, type of day and date when energy is consumed.
You can view the TOU active rates and seasons through your meter’s display.
instructions on how to configure time of use on your meter.
See the ION Reference, available from www.schneider-electric.com, for a
description of the Time of use module and its settings.
Related Topics
162 7EN02-0374-00
Specifications PowerLogic™ ION7400 series
Specifications
The specifications contained in this section are subject to change without notice.
See your product’s technical datasheet at www.schneider-electric.com for the most
up-to-date and complete specifications.
See your device’s installation sheet for information related to installation.
Mechanical characteristics
ION7400 panel mount meter with integrated display and PM89RD96 remote display
IP degree of protection Display: IP54

Meter body: IP30 (except connectors)
Mounting position Vertical
Display type 1/4 VGA color graphic TFT LCD, 320 x 240 resolution
Display backlight White LED
Viewable area 70.6 x 52.9 mm (2.78 x 2.08 in)
Maximum number of option modules 4 (based on mechanical stress and required IP rating)
ION7403 DIN-mount meter
IP degree of protection Meter body: IP30 (except connectors)
Mounting position Horizontal TS35 DIN rail
Maximum number of option modules 4 (based on mechanical stress and required IP rating)
Electrical characteristics
NOTE: Reactive energy and demand values are based on the fundamental, and
do not include higher harmonics. Other energy and demand values are measured
using the entire signal including harmonics. Contact Technical Support for more
information.
Measurement accuracy
IEC 62053-22 - active energy Class 0.2S
IEC 62053-24 - reactive energy Class 0.5S
IEC 61557-12 PMD/SD/K70/0.2 and PMD/SS/K70/0.2

Active power ± 0.2%
IEC 61557-12 Class 0.2
Reactive power ± 1%
IEC 61557-12 Class 1
Apparent power ± 0.5%
IEC 61557-12 Class 0.5
Current (per phase) ± 0.2%
IEC 61557-12 Class 0.2
Voltage (L-N) ± 0.2%
IEC 61557-12 Class 0.2
Frequency ± 0.02%
IEC 61557-12 Class 0.02
7EN02-0374-00 163
PowerLogic™ ION7400 series Specifications
Power quality
IEC 61000-4-30 Class S

IEC 62586-1
Voltage unbalance ± 0.2%
IEC 61557-12 Class 0.2
Voltage harmonics ± 1%
Voltage THD ± 1%
Current harmonics ± 1%
Current THD ± 1%
Flicker IEC 61000-4-30 Class S
Voltage inputs
Maximum VT/PT primary 1.0 MV AC
Specified accuracy range 57 to 400 V L-N / 100 to 690 V L-L (Wye) or 100 to 600 V L-L (Delta)
UL Listed up to 347 V L-N / 600 V L-L
Measurement category CAT III
Overload 600 V L-N / 1035V L-L

Impedance 5 MΩ
Specified accuracy frequency 42 to 69 Hz (50/60 Hz nominal)
Current inputs
CT secondary Nominal: 5 A (Class 0.2S) or 1 A (Class 0.5S)
Measured current 50 mA – 10 A
Starting current 5 mA
Withstand 20 A continuous
50 A at 10 sec/hr
500 A at 1 sec/hr
Impedance < 0.3 mΩ
Frequency 42 to 69 Hz (50/60 Hz nominal)
Burden < 0.024 VA at 10 A
AC control power
Operating range 50/60 Hz ± 10%: 90 to 415 V AC L-N ± 10%
Installation category CAT III
Burden 7.2 W / 18.0 VA max at 415 V AC (meter only)

18 W / 36.0 VA max at 415 V AC (fully optioned meter)
Frequency 45 to 65 Hz
Ride-through time 100 ms (6 cycles at 60 Hz) min., any condition

200 ms (12 cycles at 60 Hz) typ., 120 V AC
500 ms (30 cycles at 60 Hz) typ., 415 V AC
164 7EN02-0374-00
DC control power
Operating range 120 to 300 V DC ± 10%
Burden 6 W max at 300 V DC (meter only)

17 W max at 300 V DC (fully optioned meter)
Ride-through time 100 ms (6 cycles at 60 Hz) min., any condition
Digital outputs
Number 1
Type Form A solid-state
Maximum load voltage 30 V AC / 60 V DC
Maximum load current 75mA

ON resistance 13 – 40 Ω at 25 °C (77 °F)
Signal type Continuous or pulse
Pulse frequency ≤ 25 Hz
Digital inputs
Number 3
Type Externally excited
Event timestamp accuracy ± 1 ms
Voltage OFF 0 - 1.7 V AC / 0 - 2.5 V DC
Voltage ON 4- 30 V AC / 4- 60 V DC
Frequency ≤ 25 Hz
IRIG-B IRIG-B00x format (unmodulated IRIG-B time code)

Coded expressions 0 to 7 are supported but the year data is not used.
Response time 20 ms
Pulse width 20 ms
Current draw ON: ≤ 2.5 mA at maximum voltage
OFF: ≤ 0.5 mA
Environmental characteristics
Operating temperature -25 ºC to Max temp (-13 ºF to Max temp)
Maximum operation temperature is based on the quantity and type of attached option modules.
See Maximum operating temperature, page 166.
Storage temperature -40 to 85 °C (-40 to 185 °F)
Humidity rating 5 – 95% RH non-condensing

Maximum dewpoint: 37 °C (99 °F)
Pollution degree 2
Altitude < 3000 m (9843 ft)
Location/mounting Not suitable for wet locations

For indoor use only
Must be permanently connected and fixed
7EN02-0374-00 165
Maximum operating temperature
Max temp PM89M2600 PM89M0024

Digital (2 out, 6 in) Analog (2 out, 4 in)
70 ºC (158 ºF) 0–4 0,1
70 ºC (158 ºF) 0 2
60 ºC (140 ºF) 1, 2 2–4
LEDs
Energy pulsing LEDs (visible and infrared) located on top of meter
Type Visible orange, infrared
Wavelength 611 nm peak (orange) 940 nm (infrared)
Maximum pulse rate 42 – 69 Hz (based on line frequency)
WATT and VAR energy pulsing LEDs (visible and infrared) located on integrated display
Type Visible orange, infrared
Wavelength 611 nm peak (orange) 940 nm (infrared)
Maximum pulse rate 42 – 69 Hz (based on line frequency)
EMC (electromagnetic compatibility)

Product standards IEC 62052-11
IEC 61326-1
Immunity to electrostatic discharge IEC 61000-4-2
Immunity to radiated fields IEC 61000-4-3
Immunity to fast transients IEC 61000-4-4
Immunity to surges IEC 61000-4-5
Immunity to voltage dips and IEC 61000-4-11

interruptions
Immunity to magnetic fields IEC 61000-4-8
Immunity to ring waves IEC 61000-4-12
Immunity to conducted disturbances, 2 CLC/TR 50579

- 150 kHz
Radiated and conducted emissions FCC part 15 Class B, EN55022 Class B, ICES-003 Class B, EN55011
Surge withstand capacity (SWC) ANSI C37.90.1
Harmonic current emissions IEC 61000-3-2

Flicker (voltage fluctuation) limits IEC 61000-3-3
Mechanical compliance
Vibration IEC 60068-2-6
Shock IEC 60068-2-27
166 7EN02-0374-00
Safety
Safety construction IEC/EN 61010-1 ed.3, CAT III, 400 VLN / 690 V LL
UL 61010-1 ed.3 and CSA-C22.2 No. 61010-1 ed.3, CATIII, 347 V LN / 600 V LL
IEC/EN 62052-11, Protective Class II
Ethernet communications
Number of ports 2 (the second connector functions as an Ethernet switch for networking devices)
Maximum cable length 100 m (328 ft), per TIA/EIA 568-5-A
Cable type CAT5/5e UTP (use unshielded connector only)
Mode 10Base-T, 100Base-TX, Auto-MDIX
Data rate up to 100 Mbps
RS-485 communications
Number of ports 1
Maximum cable length 1200 m (4000 ft)
Maximum number of devices (unit Up to 32 devices on the same bus

loads)
Parity None, even, odd
Baud rate 2400 – 115200, recommend 19200
Optical port communications

Number of ports 1
Type ANSI C12.18
Parity None, even, odd
Baud rate 2400, 4800, 9600, 19200 baud
USB communications
Number of ports 1 mini–B USB, 1 type A USB
Real-time clock
Clock drift (time error) 20 ppm max at 25 °C (77 °F)
Battery backup time Minimum 7 years under specified storage conditions
7EN02-0374-00 167
Remote display
IP degree of protection Front: IP54
Rear: IP30
Cable CAT5/5e UTP (use unshielded connector only)
Option modules
METSEPM89M0024 Analog (2 out, 4 in)
Maximum number of modules 4

Input resistance < 300 Ω (current mode)
> 500 kΩ (voltage mode)
Maximum input current 20 mA
Maximum input voltage 30 V DC
Maximum meter operating temperature 25 ºC to Max temp (-13 ºF to Max temp)

METSEPM89M2600 Digital (2 out, 4 in)
Maximum number of modules 4

Maximum input voltage 30 V AC / 60 V DC
Maximum output voltage 250 V AC / 30 V DC
Maximum output current 8 A @ 250 V AC or 5 A @ 24 V DC, 20k cycles (resistive)
Maximum meter operating temperature -25 ºC to Max temp (-13 ºF to Max temp)
Other
Meter start time Typical: 18 seconds (power up to measurement)
Meter memory 512 MB
Data update rate Regular data: 1 second

High-speed: 50 – 60 Hz half-cycle
Related Topics
• Analog input applications
• Analog output applications
168 7EN02-0374-00
Schneider Electric
35 rue Joseph Monier
92500 Rueil Malmaison
France
+ 33 (0) 1 41 29 70 00
www.schneider-electric.com
As standards, specifications, and design change from time to time,

please ask for confirmation of the information given in this publication.
© 2015 – Schneider Electric. All rights reserved.

7EN02-0374-00

ION 7400 User Manual

Uploaded by

Document Informationclick to expand document informationUser Manual ION 74000

Document Informationclick to expand document information

Copyright:

Available Formats

ION 7400 User Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ION 7400 User Manual

Uploaded by

Copyright:

Available Formats

PowerLogic™ ION7400 series

About this manual

PowerLogic™ ION7403 installation sheet NHA77417

ION Reference 70002–0290

Maximum number of option modules..........................................................25

WAGES monitoring ........................................................................... 122

Verifying accuracy test ............................................................................ 157

NOTE: See IEC 60950-1:2005, Annex W for more information on communications

EN50160 including flicker monitoring

Power quality readings (THD)

Sag/swell capture for voltage and currents

True RMS metering to the 63rd harmonic

Active (kW), reactive (kVAR) and apparent (kVA) power

600 V direct connection on voltage inputs

Minimum/maximum readings of metered data

Transformer and Line Loss Compensation (TLC/LLC)

Time of use support

Trending and forecasting

Time synchronization to 1 ms accuracy

USB ports (on meters with integrated display)

Dual port Ethernet (two physical ports, one Ethernet IP address)

Multiple languages supported

Alarms (active and historic) display viewing and acknowledgment

Modbus master and Ethernet gateway protocols supported

Downloadable firmware and templates

Your meter in an energy management system

Inputs / outputs Alarming and

P owe r Monitoring Easy access

Asset and network Configurable

Improve energy ef ficiency and track compliance to green

Access highly accurate measurements and calculations for a

Data display and analysis tools

Active and historical alarms

Meter internal web server feature

Email messaging feature

ION Setup device configuration tool

Model Commercial reference Description

ION7400 METSEION7400 Panel-mounted meter with

ION7403 METSEION7403 DIN rail-mounted meter without

PM89RD96 METSEPM89RD96 Remote display (for DIN meter

PM89M2600 METSEPM89M2600 Digital I/O option module

PM89M0024 METSEPM89M0024 Analog I/O option module

PM8000SK METSEPM8000SK Voltage and current sealing kit

METSEPMAK METSEPMAK Mounting adapter kit for remote

Refer to your meter’s catalog pages, available from www.schneider-electric.com,

Parameter Default value

Username (for logging onto meter webpages) 7400

RS-485 Unit ID: 100

Volts Mode 4W-Wye, Delta, 3W-Wye, The power system’s configuration

PhaseOrder ABC, ACB The power system’s phase order

Parameter Values Description

PT Primary 1 to 999,999.99 The potential transformer’s primary winding

PT Secondary 1 to 999,999.99 The potential transformer’s secondary winding

CT Primary 1 to 999,999.99 The current transformer’s primary winding

CT Secondary 1 to 999,999.99 The current transformer’s secondary winding

I4 Primary 1 to 999,999.99 The I4 current transformer’s primary winding

I4 Secondary 1 to 999,999.99 The I4 current transformer’s secondary winding

Voltage polarity setup