Schneider 5330

PowerLogic™ PM5300 series
User manual
EAV15107-EN09
04/2021
www.se.com
Legal Information
The Schneider Electric brand and any trademarks of Schneider Electric SE and its
subsidiaries referred to in this guide are the property of Schneider Electric SE or its
subsidiaries. All other brands may be trademarks of their respective owners.
This guide and its content are protected under applicable copyright laws and
furnished for informational use only. No part of this guide may be reproduced or
transmitted in any form or by any means (electronic, mechanical, photocopying,
recording, or otherwise), for any purpose, without the prior written permission of
Schneider Electric.
Schneider Electric does not grant any right or license for commercial use of the guide
or its content, except for a non-exclusive and personal license to consult it on an "as
is" basis. Schneider Electric products and equipment should be installed, operated,
serviced, and maintained only by qualified personnel.
As standards, specifications, and designs change from time to time, information
contained in this guide may be subject to change without notice.
To the extent permitted by applicable law, no responsibility or liability is assumed by
Schneider Electric and its subsidiaries for any errors or omissions in the informational
content of this material or consequences arising out of or resulting from the use of the
information contained herein.
Safety information
Important information
Read these instructions carefully and look at the equipment to become familiar
with the device before trying to install, operate, service, or maintain it. The
following special messages may appear throughout this manual or on the
equipment to warn of potential hazards or to call attention to information that
clarifies or simplifies a procedure.
The addition of either symbol to a “Danger” or “Warning” safety label indicates

that an electrical hazard exists which will result in personal injury if the
instructions are not followed.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that accompany this symbol to avoid possible
injury or death.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in
death or serious injury.
Failure to follow these instructions will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result
in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to physical injury.
Please note
Electrical equipment should be installed, operated, serviced and maintained only
by qualified personnel. No responsibility is assumed by Schneider Electric for any
consequences arising out of the use of this material. A qualified person is one who
has skills and knowledge related to the construction, installation, and operation of
electrical equipment and has received safety training to recognize and avoid the
hazards involved.
EAV15107-EN09 3
Notices
FCC
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that the interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The user is cautioned that any changes or modifications not expressly approved
by Schneider Electric could void the user’s authority to operate the equipment.
This digital apparatus complies with CAN ICES-3 (B) /NMB-3(B).
4 EAV15107-EN09
Table of Contents
Safety precautions ......................................................................................9
Meter overview .......................................................................................... 11
Features and options ................................................................................ 11
Data display and analysis tools ..................................................................13
Meter configuration ...................................................................................13
Hardware reference ..................................................................................15
Parts of the meter (rear view).....................................................................15
LED indicators on the display ....................................................................15
Panel-mount meter mounting and wiring recommendations .........................16
Terminal covers ........................................................................................16
Meter wiring considerations .......................................................................16
Communications connections....................................................................19
Display ........................................................................................................20
Display overview ......................................................................................20
Default data display screen .......................................................................20
Notification icons ......................................................................................21
Meter display language .............................................................................21
Meter screen navigation ............................................................................21
Data display screens.................................................................................25
HMI setup screens....................................................................................28
Setting up the display ..........................................................................28
Basic setup ................................................................................................30
Configuring basic setup parameters using the display .................................30
Configuring advanced setup parameters using the display...........................32
Setting up regional settings .......................................................................32
Setting up the screen passwords ...............................................................33
Lost user access.................................................................................34
Setting the clock .......................................................................................34
Cybersecurity.............................................................................................36
Cybersecurity overview .............................................................................36
Product defense-in-depth ..........................................................................36
Device security capabilities..................................................................36
Protected environment assumptions.....................................................37
Potential risks and compensating controls ............................................37
Default security settings ............................................................................38
Display passwords....................................................................................38
Harden the device ....................................................................................38
Enabling/Disabling communication protocols ........................................39
Firmware upgrades...................................................................................39
Secure disposal guidelines........................................................................39
Secure disposal checklist ....................................................................39
Disposal, reuse, recycling....................................................................39
Communications .......................................................................................41
Serial communications ..............................................................................41
Ethernet communications..........................................................................42
BACnet/IP................................................................................................43
Supported BACnet features .................................................................44
EAV15107-EN09 5
BACnet/IP communications implementation..........................................45

BACnet objects...................................................................................46
Logging .......................................................................................................54
Data log ...................................................................................................54
Alarm log .................................................................................................55
Memory allocation for log files....................................................................55
Inputs / outputs ..........................................................................................56
Available I/O ports ....................................................................................56
Status input applications ...........................................................................56
Digital output applications .........................................................................58
Relay output applications ..........................................................................61
Energy pulsing .........................................................................................63
Alarms.........................................................................................................66
Alarms overview .......................................................................................66
Available alarms .......................................................................................66
Unary alarms............................................................................................66
Available unary alarms ........................................................................66
Digital alarms ...........................................................................................66
Standard alarms .......................................................................................67
Alarm priorities .........................................................................................71
Alarm setup overview................................................................................72
LED alarm indicator ..................................................................................74
Alarm display and notification ....................................................................75
Active alarms list and alarm history log .......................................................75
Viewing active alarm details using the display .......................................76
Viewing alarm history details using the display ......................................76
Viewing alarms counters using the display ............................................76
Acknowledging high-priority alarms using the display.............................77
Resetting alarms using ION Setup........................................................77
Measurements ..........................................................................................78
Real-time readings ...................................................................................78
Energy.....................................................................................................78
Configuring the energy scaling using ION Setup....................................78
Preset energy...........................................................................................79
Configuring the preset energy using ION Setup .....................................79
Min/max values ........................................................................................80
Demand...................................................................................................80
Power factor (PF) .....................................................................................84
Timers .....................................................................................................88
Resets.........................................................................................................89
Multi-tariffs .................................................................................................91
Multi-tariff.................................................................................................91
Command mode overview.........................................................................92
Time of day mode overview .......................................................................92
Input mode overview.................................................................................95
Power quality .............................................................................................97
Power quality measurements ....................................................................97
Harmonics overview .................................................................................97
Total harmonic distortion %........................................................................97
Total demand distortion .............................................................................97
6 EAV15107-EN09
Harmonic content calculations ...................................................................98

THD% calculations ...................................................................................98
thd calculations ........................................................................................98
TDD calculations ......................................................................................98
Viewing harmonics using the display ..........................................................98
Viewing TDD using the display ..................................................................99
Viewing THD/thd using the display .............................................................99
Maintenance ............................................................................................ 101
Maintenance overview ............................................................................ 101
Power meter memory.............................................................................. 101
Firmware version, model and serial number.............................................. 101
Diagnostics information........................................................................... 103
Control power (auxiliary power) interruption event ..................................... 103
Acknowledging control power (auxiliary power) interruption event
using the display ............................................................................... 103
Troubleshooting ..................................................................................... 104
Technical assistance............................................................................... 106
Verifying accuracy................................................................................... 107
Overview of meter accuracy .................................................................... 107
Accuracy test requirements ..................................................................... 107
Energy pulsing.................................................................................. 108
Meter settings for accuracy testing ........................................................... 108
Verifying accuracy test ............................................................................ 108
Accuracy verification test points ............................................................... 111
Energy pulsing considerations ................................................................. 111
VT and CT considerations........................................................................ 111
Total power limits .................................................................................... 112
Typical sources of test errors ................................................................... 112
MID compliance ...................................................................................... 113
MID-compliant models ............................................................................ 113
Protected setup parameters and functions................................................ 113
Locking or unlocking the meter ................................................................ 113
Setting up the lock password ................................................................... 114
Device specifications .............................................................................. 115
China Standard Compliance ................................................................. 120
EAV15107-EN09 7
Safety precautions PowerLogic™ PM5300 series
Safety precautions
Installation, wiring, testing and service must be performed in accordance with all
local and national electrical codes.
DANGER
HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH
• Apply appropriate Personal Protective Equipment (PPE) and follow safe
electrical work practices. See NFPA 70E, CSA Z462 or other local
standards.
• Turn off all power supplying this device and the equipment in which it is
installed before working on or in the equipment.
• Always use a properly rated voltage sensing device to confirm that all power
is off.
• Follow guidelines in the Wiring section of the related Installation Sheet.
• Assume communications and I/O wiring are hazardous live until determined
otherwise.
• Do not exceed the maximum ratings of this device.
• Do not short secondary terminals of Voltage Transformer (VT).
• Do not open secondary terminals of Current Transformer (CT).
• Ground secondary circuit of CTs.
• Do not use the data from the meter to confirm power is off.
• Replace all devices, doors and covers before turning on power to this
equipment.
NOTE: See IEC 60950-1 for more information on communications and I/O
wiring connected to multiple devices.
WARNING
UNINTENDED OPERATION
• Do not use this device for critical control or protection of persons, animals,
property or equipment.
• Do not use this device if a wrench icon appears on the top left corner
of the display screen or if the value under Meter Status is not “OK”.
Failure to follow these instructions can result in death, serious injury, or
equipment damage.
EAV15107-EN09 9
PowerLogic™ PM5300 series Safety precautions
WARNING
POTENTIAL COMPROMISE OF SYSTEM AVAILABILITY, INTEGRITY, AND
CONFIDENTIALITY
• Change default passwords/passcodes to help prevent unauthorized access
to device settings and information.
• Disable unused ports/services and default accounts, where possible, to
minimize pathways for malicious attacks.
• Place networked devices behind multiple layers of cyber defenses (such as
firewalls, network segmentation, and network intrusion detection and
protection).
• Use cybersecurity best practices (for example: least privilege, separation of
duties) to help prevent unauthorized exposure, loss, modification of data and
logs, interruption of services, or unintended operation.
equipment damage.
10 EAV15107-EN09
Meter overview PowerLogic™ PM5300 series
Meter overview
Features and options
The PowerLogic™ PM5300 power and energy meters offer value for the
demanding needs of your energy monitoring and cost management applications.
PM5310 PM5320 PM5330 PM5340
PM5331 PM5341
Fast installation, panel mount with integrated display ✔ ✔ ✔ ✔
Accuracy IEC 61557-12 Cl 0.5S Cl 0.5S Cl 0.5S Cl 0.5S
Display ✔ ✔ ✔ ✔
Backlit LCD, multilingual, bar graphs, 6 lines, 4
concurrent values
Power and energy metering: 3-phase voltage, ✔ ✔ ✔ ✔
current, power, demand, energy, frequency, power
factor
Multi-tariff 4 4 4 4
Power quality analysis: THD, thd, TDD ✔ ✔ ✔ ✔
Power quality analysis: Harmonics, individual (odd) 31st 31st 31st 31st
up to
I/O 2SI/2DO 2SI/2DO 2SI/2DO 2SI/2DO

Relays — — 2 2
Alarms 35 35 35 35
Setpoint response time, seconds 1 1 1 1
Single and multi-condition alarms ✔ ✔ ✔ ✔
Communications: Serial ports with Modbus protocol 1 — 1 —
Communications: Ethernet port with Modbus TCP — 1 — 1

and BACnet/IP
MID-ready compliance — — PM5331 PM5341
Functions and characteristics

General
Use on LV and MV systems ✔
Basic metering with THD and min/max readings ✔
Instantaneous rms values
Current (per phase and neutral) ✔
Voltage (total, per phase L-L and L-N) ✔
Frequency ✔
Real, reactive, and apparent power (Total and Signed, Four Quadrant
per phase)
True Power Factor (Total and per phase) Signed, Four Quadrant
Displacement PF (Total and per phase) Signed, Four Quadrant
% Unbalanced I, V L-N, V L-L ✔
EAV15107-EN09 11
PowerLogic™ PM5300 series Meter overview
Energy values
Accumulated Active, Reactive and Apparent Received/Delivered; Net and absolute

Energy1
1Stored in non-volatile memory
Demand values
Current average1 Present, Last, Predicted, Peak, and Peak Date

Time
Active power1 Present, Last, Predicted, Peak, and Peak Date
Time
Reactive power1 Present, Last, Predicted, Peak, and Peak Date
Time
Apparent power1 Present, Last, Predicted, Peak, and Peak Date
Time
Demand calculation (Sliding, fixed and rolling ✔
block, thermal methods)
Synchronization of the measurement window to ✔

input, communication command or internal clock
Configurable demand intervals ✔
Power quality measurements
THD, thd (Total Harmonic Distortion) I, V L-N, V I, V L-N, V L-L

L-L per phase
TDD (Total Demand Distortion) ✔
Individual harmonics (odds) 31st
Other measurements
I/O timer1 ✔
Operating timer1 ✔
Load timer1 ✔
Alarm counters and alarm logs ✔
Data recording
Min/max of instantaneous values, plus phase ✔

identification1
Alarms with 1s timestamping1 Data logging Up to two fixed parameters (e.g.,
kWh and kVAh) with configurable interval and
duration (e.g., 2 parameters for 60 days at 15
minutes interval)
Memory capacity 256 kB
Min/max log ✔
Maintenance, alarm and event logs ✔
Inputs/Outputs/Relays
Digital inputs 2
Digital outputs 2
Form A Relay outputs 2
12 EAV15107-EN09
Meter overview PowerLogic™ PM5300 series
Inputs/Outputs/Relays (Continued)
Timestamp resolution in seconds 1
Whetting voltage ✔
Data display and analysis tools

Power Monitoring Expert
EcoStruxure™ Power Monitoring Expert is a complete supervisory software
package for power management applications.
The software collects and organizes data gathered from your facility’s electrical
network and presents it as meaningful, actionable information via an intuitive web
interface.
Power Monitoring Expert communicates with devices on the network to provide:
• Real-time monitoring through a multi-user web portal
• Trend graphing and aggregation
• Power quality analysis and compliance monitoring
• Preconfigured and custom reporting
See the EcoStruxure™ Power Monitoring Expert online help for instructions on
how to add your device into its system for data collection and analysis.
Power SCADA Operation

EcoStruxure™ Power SCADA Operation is a complete real-time monitoring and
control solution for large facility and critical infrastructure operations.
It communicates with your device for data acquisition and real-time control. You
can use Power SCADA Operation for:
• System supervision
• Real-time and historical trending, event logging
• PC-based custom alarms
See the EcoStruxure™ Power SCADA Operation online help for instructions on
how to add your device into its system for data collection and analysis.
Modbus command interface

Most of the meter’s real-time and logged data, as well as basic configuration and
setup of meter features, can be accessed and programmed using a Modbus
command interface as published in the meter’s Modbus register list.
This is an advanced procedure that should only be performed by users with
advanced knowledge of Modbus, their meter, and the power system being
monitored. For further information on the Modbus command interface, contact
Technical Support.
See your meter’s Modbus register list at www.se.com for the Modbus mapping
information and basic instructions on command interface.
Meter configuration
Meter configuration can be performed through the display or PowerLogic™ ION
Setup.
ION Setup is a meter configuration tool that can be downloaded for free at
www.se.com.
EAV15107-EN09 13
PowerLogic™ PM5300 series Meter overview
See the ION Setup online help or in the ION Setup device configuration guide. To
download a copy, go to www.se.com and search for ION Setup device
configuration guide.
14 EAV15107-EN09
Hardware reference PowerLogic™ PM5300 series
Hardware reference
Parts of the meter (rear view)
Most of the input, output and communication ports are located on the back of the
meter.
A Relay outputs
B Voltage inputs
C Control power
D Current inputs
E Status inputs/Digital outputs
F Communication port (Ethernet or RS-485)
G Gasket
LED indicators on the display

The display has two LED indicators.
A Alarm / energy pulsing LED (orange)
B Heartbeat / communications LED (green)
Alarm / energy pulsing LED

The alarm / energy pulsing LED can be configured for alarm notification or energy
pulsing.
When configured for alarm notification, this LED flashes when a high, medium or
low priority alarm is active. The LED provides a visual indication of an active alarm
condition or an inactive but unacknowledged high priority alarm.
When configured for energy pulsing, this LED flashes at a rate proportional to the
amount of energy consumed. This is typically used to verify the power meter’s
accuracy.
Heartbeat / serial communications LED

The heartbeat / serial communications LED blinks to indicate the meter’s
operation and serial Modbus communications status.
The LED blinks at a slow, steady rate to indicate the meter is operational. The LED
flashes at a variable, faster rate when the meter is communicating over a Modbus
serial communications port.
You cannot configure this LED for other purposes.
EAV15107-EN09 15
PowerLogic™ PM5300 series Hardware reference
NOTE: A heartbeat LED that remains lit and does not blink (or flash) can
indicate a problem. In this case, power down the meter and reapply power. If
the LED still does not blink or flash, contact Technical Support.
Ethernet communications LEDs

The meter has two LEDs for the Ethernet communications port.
The Link LED is on when there is a valid Ethernet connection. The Act (active)
LED flashes to indicate the meter is communicating through the Ethernet port.
You cannot configure these LEDs for other purposes.
Panel-mount meter mounting and wiring recommendations

There are supplemental mounting and wiring recommendations that apply to
panel-mount meters.
• The meter is intended to be mounted inside a ¼-DIN panel cutout.
• Inspect the gasket (installed around the perimeter of the display) and make
sure it is secured properly and not damaged.
• The meter retainer clips, located on either side of the meter base and used to
secure the meter in the panel, do not usually require any tools to install.
Terminal covers
The voltage and current terminal covers help prevent tampering with the meter’s
voltage and current measurement inputs.
The terminal covers enclose the terminals, the conductor fixing screws and a
length of the external conductors and their insulation. The terminal covers are
secured by tamper-resistant meter seals.
These covers are included for meter models where sealable voltage and current
covers are required to comply with revenue or regulatory standards.
The meter terminal covers must be installed by a qualified installer.
Refer to your meter's installation sheet or the instructions that came with your
terminal covers for instructions on installing the terminal covers.
Meter wiring considerations

Direct connect voltage limits
You can connect the meter’s voltage inputs directly to the phase voltage lines of
the power system if the power system’s line-to-line or line-to-neutral voltages do
not exceed the meter’s direct connect maximum voltage limits.
The meter's voltage measurement inputs are rated by the manufacturer for up to
400 V L-N / 690 V L-L. However, the maximum voltage allowed for direct
connection may be lower, depending on the local electrical codes and regulations.
In US and Canada the maximum voltage on the meter voltage measurement
inputs may not exceed 347 V L-N / 600 V L-L.
If your system voltage is greater than the specified direct connect maximum
voltage, you must use VTs (voltage transformers) to step down the voltages.
16 EAV15107-EN09
Power system Meter setting Symbol Direct connect Direct connect # of VTs (if
description maximum (UL) maximum (IEC) required)
Single-phase 2-wire 1PH2W LN 347 V L-N 400 V L-N 1 VT

line-to-neutral
Single-phase 2-wire 1PH2W LL 600 V L-L 600 V L-L 1 VT

line-to-line
Single-phase 3-wire 1PH3W LL with N 347 V L-N / 600 V 400 V L-N / 690 V 2 VT
line-to-line with L-L L-L
neutral
3-phase 3-wire 3PH3W Dlt Ungnd 600 V L-L 600 V L-L 2 VT

Delta ungrounded
3-phase 3-wire 3PH3W Dlt Crnr 600 V L-L 600 V L-L 2 VT

Delta corner Gnd
grounded
3-phase 3-wire Wye 3PH3W Wye Ungnd 600 V L-L 600 V L-L 2 VT
ungrounded
3-phase 3-wire Wye 3PH3W Wye Gnd 600 V L-L 600 V L-L 2 VT
grounded
3-phase 3-wire Wye 3PH3W Wye Res 600 V L-L 600 V L-L 2 VT
resistance-grounded Gnd
EAV15107-EN09 17
PowerLogic™ PM5300 series Hardware reference
Power system Meter setting Symbol Direct connect Direct connect # of VTs (if
description maximum (UL) maximum (IEC) required)
3-phase 4-wire open 3PH4W Opn Dlt Ctr 240 V L-N / 415 V 240 V L-N / 415 V 3 VT
Delta center-tapped Tp L-N / 480 V L-L L-N / 480 V L-L
3-phase 4-wire 3PH4W Dlt Ctr Tp 240 V L-N / 415 V 240 V L-N / 415 V 3 VT
Delta center-tapped L-N / 480 V L-L L-N / 480 V L-L
3-phase 4-wire 3PH4W Wye Ungnd 347 V L-N / 600 V 347 V L-N / 600 V 3 VT or 2 VT
ungrounded Wye L-L L-L
3-phase 4-wire 3PH4W Wye Gnd 347 V L-N / 600 V 400 V L-N / 690 V 3 VT or 2 VT
grounded Wye L-L L-L
3-phase 4-wire 3PH4W Wye Res 347 V L-N / 600 V 347 V L-N / 600 V 3 VT or 2 VT
resistance-grounded Gnd L-L L-L
Wye
Balanced system considerations

In situations where you are monitoring a balanced 3-phase load, you may choose
to connect only one or two CTs on the phase(s) you want to measure, and then
configure the meter so it calculates the current on the unconnected current
input(s).
NOTE: For a balanced 4-wire Wye system, the meter’s calculations assume
that there is no current flowing through the neutral conductor.
Balanced 3-phase Wye system with 2 CTs

The current for the unconnected current input is calculated so that the vector sum
for all three phases equal zero.
Balanced 3-phase Wye or Delta system with 1CT

The currents for the unconnected current inputs are calculated so that their
magnitude and phase angle are identical and equally distributed, and the vector
sum for all three phase currents equal zero.
NOTE: You must always use 3 CTs for 3-phase 4-wire center-tapped Delta or
center-tapped open Delta systems.
18 EAV15107-EN09
Communications connections
RS-485 wiring
Connect the devices on the RS-485 bus in a point-to-point configuration, with the
(+) and (-) terminals from one device connected to the corresponding (+) and (-)
terminals on the next device.
RS-485 cable
Use a shielded 2 twisted pair or 1.5 twisted pair RS-485 cable to wire the devices.
Use one twisted pair to connect the (+) and (-) terminals, and use the other
insulated wire to connect the C terminals
The total distance for devices connected on an RS-485 bus should not exceed
1200 m (4000 ft).
RS-485 terminals
C Common. This provides the voltage reference (zero volts) for the data plus and data minus
signals
Shield. Connect the bare wire to this terminal to help suppress signal noise that may be
present. Ground the shield wiring at one end only (either at the master or the last slave
device, but not both.
- Data minus. This transmits/receives the inverting data signals.
+ Data plus. This transmits/receives the non-inverting data signals.
NOTE: If some devices in your RS-485 network do not have the Common
terminal, use the bare wire in the RS-485 cable to connect the Common
terminal from the meter to the shield terminal on the devices that do not have
the Common terminal.
Ethernet communications connections

Use a shielded Ethernet cable to connect the meter’s Ethernet port.
Ground terminal is not available on the meter; shield should be connected to
ground at the other end. Your Ethernet connection source should be installed in a
location that minimizes the overall Ethernet cable routing length.
EAV15107-EN09 19
PowerLogic™ PM5300 series Display
Display
Display overview
The display lets you use the meter to perform various tasks such as setting up the
meter, displaying data screens, acknowledging alarms, or performing resets.
A Navigation / menu selection

G F E buttons
B Heartbeat / communications
LED (green)
C Alarm / energy pulsing LED

(orange)
D Navigation symbols or menu

D options
H
E Right notification area
C
B F Screen title
A G Left notification area

H Cursor
Default data display screen

The default data display screen varies depending on the meter model.
The Summary screen is the default screen for all meter models except PM5331 /
PM5341.
The Summary screen displays real-time values for average voltage and current
(Vavg, Iavg), total power (Ptot) and energy consumption (E Del).
The Power System screen is the default screen for PM5331 / PM5341 meter
models.
A Accumulated real energy (delivered +

received)
B Active tariff
C System frequency
D Power system setting
E Control power (auxiliary power) interruption

event icon
F Locked / unlocked icon
20 EAV15107-EN09
Display PowerLogic™ PM5300 series
Notification icons
To alert you about meter state or events, notification icons appear at the top left or
top right corner of the display screen.
Icon Description
The wrench icon indicates that the power meter

requires maintenance.
The alarm icon indicates an alarm condition has

occurred.
The blinking heartbeat icon indicates that the

power meter is in normal operating condition.
The icon indicates that a control power (auxiliary

power) interruption event has occurred.
(Displayed only in MID compliance meter
models)
Meter display language

You can configure the meter to display the information on the display screen in
one of several languages.
The following languages are available:
• English
• French
• Spanish
• German
• Italian
• Portuguese
• Russian
• Chinese
Meter screen navigation

The meter’s buttons and display screen allow you to navigate data and setup
screens, and to configure the meter’s setup parameters.
EAV15107-EN09 21
A. Press the button below the

appropriate menu to view
that screen
B. Press the right arrow to
view more screens
C. In setup mode, a small
right arrow indicates the
selected option
D. In setup mode, a small
down arrow indicates that
there are additional
parameters to display. The
down arrow disappears
when there are no more
parameters to display.
E. In setup mode, press the
button under Edit to
change that setting. If the
item is read-only, cannot
be configured with the
meter’s existing setup, or
can only be configured
using software, Edit
disappears.
Navigation symbols
Navigation symbols indicate the functions of the associated buttons on your
meter’s display.
Symbol Description Actions
Right arrow Scroll right and display more menu items or move cursor
one character to the right
Up arrow Exit screen and go up one level
Small down Move cursor down the list of options or display more items
arrow below
Small up arrow Move cursor up the list of items or display more items
above
Left arrow Move cursor one character to the left
Plus sign Increase the highlighted value or show the next item in the
list.
Minus sign Show the previous item in the list
When you reach the last screen, press the right arrow again to cycle through the
screen menus.
Meter screen menus overview

All meter screens are grouped logically, according to their function.
You can access any available meter screen by first selecting the Level 1 (top level)
screen that contains it.
Level 1 screen menus - IEEE title [IEC title]

Amps [I] Volts [U-V] Power [PQS] Energy [E] PF Hz [F] THD
Harm Unbal MnMx Alarm I/O Timer QR Maint Clock
22 EAV15107-EN09
Menu tree
Use the menu tree to navigate to the parameter or setting you want to view or
configure.
Level 1, 2 and 3 meter screens - IEEE title [IEC title]
The image below summarizes the available meter screens (IEEE menus shown, with the corresponding IEC
menus in parentheses).
EAV15107-EN09 23
Level 1 Level 2 Level 3

Amps
Amps [I]
[I]
Dmd Iavg Pk DT
Volts
V L-L [U]
[U-V]
V L-N [V]
Power
Power [PQS]
[PQS]
Phase Active [P] Reac [Q] Appr [S]
Dmd Wd [Pd] Wd [Pd] Pk DT
VARd [Qd] VARd [Qd] Pk DT
VAd [Sd] VAd [Sd] Pk DT
QR
Energy Wh
[E]
VAh
VARh
Tariff T1 T2 T3 T4
QR
PF True
Disp
Hz
[F] (Frequency)
THD THD Amps [I] V L-L [U] V L-N [V]

thd Amps [I] V L-L [U] V L-N [V]
QR
Harm V L-L [U] 3-11 13-21 23-31

V L-N [V] 3-11 13-21 23-31
Amps [I] 3-11 13-21 23-31
TDD
Unbal (Unbalance)
MnMx Amps [I]

Volts [U-V] V L-L [U] V L-N [V]
Power [PQS] Active [P] Reac [Q] Appr [S]
PF True Disp
Hz [F]
THD THD Amps [I] V L-L [U] V L-N [V]
thd Amps [I] V L-L [U] V L-N [V]
Unbal Amps [I] V L-L [U] V L-N [V]

QR
Alarm Active
Hist
Count
Unack
QR
I/O D Out D1 D2
S In S1 S2
Relay R1 R2 (PM5330 / PM5331 / PM5340 / PM5341 only)
Timer Load
Oper
QR Info Energy Dmd Basic PQ Alarm MnMx Log#1 Log#2
Maint Reset
Setup Meter Basic Advan Dmd Tariff
Comm Serial Enet BACnet (Serial: PM5310 / PM5330 / PM5331 only)
(Enet and BACnet: PM5320 / PM5340 / PM5341 only)
Alarm 1-Sec Unary Dig
I/O LED S In D Out Relay (PM5330 / PM5331 / PM5340 / PM5341 only)
HMI Displ Region Pass
Clock
Diag Info
Meter
Cl Pwr
PhAng
QR
Clock (Clock parameters)
24 EAV15107-EN09
Data display screens

The meter display screens allow you to view meter values and configure settings.
The titles listed are for the HMI mode in IEEE, with the corresponding titles in IEC
mode in square brackets [ ].
• Bulleted items indicate subscreens and their descriptions.
Amps [I]
Amps [I] Instantaneous current measurements for each phase and calculated neutral (In) or calculated
ground current (Ig) based on the meter wiring type.
Dmd Summary of peak current demand values at the last demand interval.
• Iavg • Real-time demand (Pres), peak demand (Peak) and predicted demand (Pred) for the
present interval. Average demand for the previous (Last) interval.
• Pk DT • Date and timestamp for the peak demand readings.
Volts [U-V]
V L-L [U] Line-to-line voltage for each phase.
V L-N [V] Line-to-neutral voltage for each phase.
Power [PQS]
Power [PQS] Summary of real-time power consumption values for total active power in kW (Total [Ptot]), total
reactive power in kVAR (Total [Qtot]), and total apparent power in kVA (Total [Stot]).
Phase Per phase (A [P1], B [P2], C [P3]) and total (Total [Ptot]) power values for active power in kW,
• Active [P], Reac [Q], Appr [S] reactive power in kVAR and apparent power in kVA.
Dmd Summary of peak power demand values in the previous (Last) demand interval period for active
power in kW, reactive power in kVAR and apparent power in kVA.
• Wd [Pd], VARd [Qd], VAd [Sd] • Total power demand values in the previous (Last) demand interval for active power
demand (Wd [P]), reactive power demand (VARd [Q]) and apparent power demand (VAd
◦ Pk DT [S]). Displays demand values for the present demand (Pres) interval, demand for the
previous demand (Last) interval period, predicted demand (Pred) based on the current
power consumption rate, and the recorded peak power demand (Peak) value.
◦ Date and timestamp for the peak power demand (Peak) value.
• QR • Power demand parameters embedded in QR code format.
Energy [E]
Wh, VAh, VARh Delivered (Del), received (Rec), delivered plus received (D+R) and delivered minus received (D-
R) accumulated values for active energy (Wh), apparent energy (VAh) and reactive energy
(VARh).
Tariff
• T1, T2, T3, T4 • Displays the available multi-tariffs (T1 through T4).
◦ Del ◦ Active energy delivered in Wh (W [P]), reactive energy delivered in VARh (VAR [Q])
and apparent energy delivered in VAh (VA [S]) energy for the selected multi-tariff.
◦ Active energy received in Wh (W [P]), reactive energy received in VARh (VAR [Q]) and
◦ Rec apparent energy received in VAh (VA [S]) energy for the selected multi-tariff
QR Energy parameters (Wh, VAh, VARh, and multi-tariff) embedded in QR code format.
PF
True Per phase and total true power factor values and sign.
Disp Per phase and total displacement power factor values and sign.
Hz [F]
Frequency (Freq). This page also displays average voltage (Vavg), average current (Iavg) and total power factor (PF) values.
EAV15107-EN09 25
THD
THD THD (ratio of harmonic content to the fundamental) for current, line-to-line voltage and line-to-
• Amps [I], V L-L [U], V L-N [V] neutral voltage.
thd thd (ratio of harmonic content to the rms value of total harmonic content) for current, line-to-line
• Amps [I], V L-L [U], V L-N [V] voltage and line-to-neutral voltage.
QR Power quality parameters (THD and thd) embedded in QR code format.
Harm
V L-L [U] Line-to-line voltage harmonics data: Numeric magnitude and angle for the fundamental
• 3-11, 13-21, 23-31 harmonic, and graphical representation of harmonics for the 3rd to 11th, 13th to 21st, and 23rd
to 31st odd harmonics for each line-to-line phase voltage.
V L-N [V] Line-to-neutral voltage harmonics data: Numeric magnitude and angle for the fundamental
• 3-11, 13-21, 23-31 harmonic, and graphical representation of harmonics for the 3rd to 11th, 13th to 21st, and 23rd
to 31st odd harmonics for each line-to-neutral phase voltage.
Amps [I] Current harmonics data: Numeric magnitude and angle for the fundamental harmonics, and
• 3-11, 13-21, 23-31 graphical representation of harmonics for the 3rd to 11th, 13th to 21st, and 23rd to 31st odd
harmonics for each phase current.
TDD Total demand distortion each phase voltage.
Unbal
Percent unbalance readings for line-to-line voltage (V L-L [U]), line-to-neutral voltage (V L-N [V]) and current (Amps [I]).
MnMx
Amps [I] Summary of minimum and maximum values for phase current.
Volts [U-V] Summary of minimum and maximum values for line-to-line voltage and line-to-neutral voltage.
• V L-L [U], V L-N [V]
Power [PQS] Minimum and maximum values for active, reactive, and apparent power.
• Active [P], Reac [Q], Appr [S]
PF Minimum and maximum values for true and displacement PF and PF sign.
• True, Disp
Hz [F] Minimum and maximum values for frequency.
THD
• THD, thd • Minimum and maximum values for total harmonic distortion (THD or thd).
◦ Amps [I], V L-L [U], V L-N ◦ THD or thd minimum and maximum values for phase or neutral current, line-to-line
[V] voltage and line-to-neutral voltage.
Unbal Minimum and maximum values for current unbalance, line-to-line voltage unbalance and line-to-
• Amps [I], V L-L [U], V L-N [V] neutral voltage unbalance.
QR Minimum and maximum values (phase current, line-to-line voltage, line-to-neutral voltage,
power (PQS), PF, frequency, power quality and Unbal) embedded in QR code format.
Alarm
Active, Hist, Count, Unack Lists all active alarms (Active), past alarms (Hist), the total number of times each standard alarm
was tripped (Count), and all unacknowledged alarms (Unack).
QR Alarm parameters (active, past alarms, the total number of times each standard alarm was
tripped, unacknowledged) embedded in QR code format.
26 EAV15107-EN09
I/O
D Out Current status (on or off) of the selected digital output, status input or relay output. Counter
shows the total number of times an off-to-on change of state is detected. Timer shows the total
• D1, D2
time (in seconds) that a digital output, status input or relay is in the on state.
S In
• S1, S2
Relay (PM5330 / PM5331 / PM5340 /
PM5341 only)
• R1, R2
Timer
Load Real-time counter that keeps track of the total number of days, hours, minutes and seconds an
active load is connected to the meter inputs.
Oper Real-time counter for the total number of days, hours, minutes and seconds the meter has been
powered.
QR
Meter info details, energy parameters, power demand parameters, basic parameter values (current, voltage and power), power quality
parameters, minimum / maximum values (phase current, line-to-line voltage, line-to-neutral voltage, power (PQS), PF, frequency, power
quality and Unbal), alarm parameters and data log parameters embedded in QR code format.
Maint
Reset Screens to perform global or single resets.
Setup
• Meter • Meter configuration screens.
◦ Basic ◦ Screens to define the power system and power system components/elements.
◦ Advan ◦ Screens to set up the active load timer and define the peak demand current for
inclusion in TDD calculations.
◦ Dmd
◦ Screens to set up power demand, current demand and input metering demand.
◦ Tariff
◦ Screens to set up multi-tariffs.
• Comm • Screens to set up serial, Ethernet and BACnet communications.

◦ Serial (PM5310 / PM5330 /
PM5331 only)
◦ Enet (PM5320 / PM5340 /
PM5341 only)
◦ BACnet (PM5320 / PM5340 /
PM5341 only)
• Alarm • Screens to set up standard (1-Sec), unary and digital alarms.

◦ 1-Sec, Unary, Dig
• I/O • Screens to set up the alarm / energy pulsing LED, digital inputs/outputs and relay outputs.
◦ LED
◦ S In
◦ D Out
◦ Relay ( PM5330 / PM5331 /
PM5340 / PM5341 only)
• HMI • Screens to configure display settings, edit regional settings, and set up meter display
◦ Displ, Region, Pass access passwords.
• Clock • Screens to set up the meter date and time.
Diag Diagnostic screens provide meter information, status and event data for troubleshooting.
• Info • The Info screen displays the meter model, serial number, date of manufacture, firmware
version (including OS - Operating System and RS - Reset System), language version,
factory programmed MAC address* (ex: 9C-35-5B-5F-4C-4D), and OS CRC (Cyclic
Redundancy Check). The OS CRC value is a number (Hexadecimal format) that identifies
the uniqueness between different OS firmware versions.
* Only applicable for PM5320 / PM5340 / PM5341 meter models.
• Meter • Displays the meter status.
• Cl Pwr • Non-MID meter models : The Cl Pwr screen displays how many times the meter lost
control power, and the date and time of its last occurrence.
EAV15107-EN09 27
Maint (Continued)
• MID meter models : The Cl Pwr screen displays how many times the meter lost control
power (auxiliary power), and the last power up and power down events with the timestamp.
• PhAng • The PhAng screen displays a graphical representation of the power system the meter is
monitoring.
• QR • Meter info details embedded in QR code format.
Clock
Meter date and time (local or GMT).
HMI setup screens

You can configure the meter’s display using the HMI setup screens.
The HMI (human-machine interface) setup screens allow you to:
• control the general appearance and behavior of the display screens,
• change the regional settings,
• change the meter passwords,
• enable or disable the QR code feature for accessing meter data.
See the Meter Insights QR code feature quick start guide for more information on
accessing meter data using QR codes.
Setting up the display

You can change the display screen’s settings, such as contrast, display and
backlight timeout and QR code display.
1. Navigate to Maint > Setup.
2. Enter the setup password (default is “0”), then press OK.
3. Navigate to HMI > Displ.
4. Move the cursor to point to the parameter you want to modify, then press
Edit.
5. Modify the parameter as required, then press OK.
6. Move the cursor to point to the next parameter you want to modify, press Edit,
make your changes, then press OK.
7. Press the up arrow to exit.
28 EAV15107-EN09
8. Press Yes to save your changes.
Display settings available using the display
Parameter Values Description
Contrast 1-9 Increase or decrease the value to increase or decrease the display contrast.
Bcklght Timeout (min) 0 - 99 Set how long (in minutes) before the backlight turns off after a period of inactivity.
Setting this to “0” disables the backlight timeout feature (i.e., backlight is always
on).
Screen Timeout (min) 0 - 99 Set how long (in minutes) before the screen turns off after a period of inactivity.
Setting this to “0” disables the screen timeout feature (i.e., display is always on).
QR Code Enable, Disable Set whether or not QR codes with embedded data are available on the display.
See the Meter Insights QR code feature quick start guide for more information
on accessing meter data using QR codes.
To configure the display using ION Setup, see the section for your meter in
the ION Setup online help or in the ION Setup device configuration guide,
available for download at www.se.com.
EAV15107-EN09 29
PowerLogic™ PM5300 series Basic setup
Basic setup
Meter configuration can be performed directly through the display or remotely
through software. See the section on a feature for instructions on configuring that
feature (for example, see the Communications section for instructions on
configuring Ethernet communications).
Configuring basic setup parameters using the display

You can configure basic meter parameters using the display.
Proper configuration of the meter’s basic setup parameters is essential for
accurate measurement and calculations. Use the Basic Setup screen to define the
electrical power system that the meter is monitoring.
If standard (1-sec) alarms have been configured and you make subsequent
changes to the meter’s basic setup, all alarms are disabled to prevent undesired
alarm operation.
WARNING
UNINTENDED EQUIPMENT OPERATION
• Verify all standard alarms settings are correct and make adjustments as
necessary.
• Re-enable all configured alarms.
equipment damage.
After saving the changes, confirm all configured standard alarm settings are still
valid, reconfigure them as required, and re-enable the alarms.
3. Navigate to Meter > Basic.
Edit.
30 EAV15107-EN09
Basic setup PowerLogic™ PM5300 series
7. Press the up arrow to exit, then press Yes to save your changes.
Basic setup parameters available using the display
Values Description
Power System
Select the power system type (power transformer) the meter is wired to.
1PH2W LN Single-phase 2-wire line-to-neutral
1PH2W LL Single-phase 2-wire line-to-line
1PH3W LL with N Single-phase 3-wire line-to-line with neutral
3PH3W Dlt Ungnd 3-phase 3-wire ungrounded delta
3PH3W Dlt Crnr Gnd 3-phase 3-wire corner grounded delta
3PH3W Wye Ungnd 3-phase 3-wire ungrounded wye
3PH3W Wye Gnd 3-phase 3-wire grounded wye
3PH3W Wye Res Gnd 3-phase 3-wire resistance-grounded wye
3PH4W Opn Dlt Ctr Tp 3-phase 4-wire center-tapped open delta
3PH4W Dlt Ctr Tp 3-phase 4-wire center-tapped delta
3PH4W Wye Ungnd 3-phase 4-wire ungrounded wye
3PH4W Wye Gnd 3-phase 4-wire grounded wye
3PH4W Wye Res Gnd 3-phase 4-wire resistance-grounded wye
VT Connect
Select how many voltage transformers (VT) are connected to the electrical power system.
Direct Con Direct connect; no VTs used
2VT 2 voltage transformers
3VT 3 voltage transformers
VT Primary (V)
1 to 1,000,000 Enter the size of the VT primary, in Volts.
VT Secondary (V)
100, 110, 115, 120 Select the size of the VT secondary, in Volts.
CT on Terminal
Define how many current transformers (CT) are connected to the meter, and which terminals they are connected to.
I1 1 CT connected to I1 terminal
I1 I2 2 CT connected to I1, I2 terminals
I1 I2 I3 3 CT connected to I1, I2, I3 terminals
CT Primary (A)
1 to 32767 Enter the size of the CT primary, in Amps.
CT Secondary (A)
1, 5 Select the size of the CT secondary, in Amps.
Sys Frequency (Hz)
50, 60 Select the frequency of the electrical power system, in Hz.
Phase Rotation
ABC, CBA Select the phase rotation of the 3-phase system.
EAV15107-EN09 31
Configuring advanced setup parameters using the display

You can configure a subset of advanced parameters using the display.
3. Navigate to Meter > Advan.
Edit.
Advanced setup parameters available using the display
Label — This label identifies the device, e.g., “Power Meter”. You cannot use the display to
edit this parameter. Use ION Setup to change the device label.
Load Timer Setpt (A) 0 - 18 Specifies the minimum average current at the load before the timer starts. The
meter begins counting the number of seconds the load timer is on (i.e., whenever
the readings are equal to or above this average current threshold.
Pk I dmd for TDD (A) 0 - 18 Specifies the minimum peak current demand at the load for inclusion in total
demand distortion (TDD) calculations. If the load current is below the minimum
peak current demand threshold, the meter does not use the readings to calculate
TDD. Set this to “0” (zero) if you want the power meter to use the metered peak
current demand for this calculation.
Setting up regional settings

You can change the regional settings to localize the meter screens and display
data in a different language, using local standards and conventions.
NOTE: In order to display a different language other than those listed in the
Language setup parameter, you need to download the appropriate language
file to the meter using the firmware upgrade process.
3. Navigate to HMI > Region.
Edit.
32 EAV15107-EN09
Regional settings available using the display
Language English US, Select the language you want the meter to display.
French,
Spanish,
German, Italian,
Portuguese,
Chinese,
Russian
Date Format MM/DD/YY, YY/ Set how you want the date to be displayed, e.g., month/
MM/DD, DD/ day/year.
MM/YY
Time Format 24Hr, AM/PM Set how you want the time to be displayed, e.g.,
17:00:00 or 5:00:00 PM.
HMI Mode IEC, IEEE Select the standards convention used to display menu
names or meter data.
Setting up the screen passwords

It is recommended that you change the default password in order to prevent
unauthorized personnel from accessing password-protected screens such as the
diagnostics and reset screens.
This can only be configured through the front panel. The factory-default setting for
all passwords is “0” (zero).
If you lose your password, you must return the meter for factory reconfiguration,
which resets your device to its factory defaults and destroys all logged data.
NOTICE
IRRECOVERABLE PASSWORD
Record your device's user and password information in a secure location.
Failure to follow these instructions can result in data loss.

3. Navigate to HMI > Pass.
Edit.
EAV15107-EN09 33
Setup 0000 - 9999 Sets the password for accessing the meter setup
screens (Maint > Setup).
Energy Resets 0000 - 9999 Sets the password for resetting the meter’s
accumulated energy values.
Demand Resets 0000 - 9999 Sets the password for resetting the meter’s recorded
peak demand values.
Min/Max Resets 0000 - 9999 Sets the password for resetting the meter’s recorded
minimum and maximum values.
Diagnostics 0000 - 9999 Sets the password for accessing the meter’s
diagnostics screens.
Lost user access

If you lose your meter’s user access (password) information, contact your local
Schneider Electric representative for instructions on how to return your meter for
factory reconfiguration.
NOTE: Have your meter’s serial number available for reference.
Setting the clock

The Clock setup screens allow you to set the meter’s date and time.
NOTE: You must always set or sync the meter time to UTC (GMT, Greenwich
Mean Time), not local time. Use the GMT Offset (h) setup parameter to
display the correct local time on the meter.
3. Navigate to Clock.
Edit.
34 EAV15107-EN09
Date DD/MM/YY Set the current date using the format displayed on screen, where DD = day, MM =
month and YY = year.
MM/DD/YY
YY/MM/DD
Time HH:MM:SS (24 hour Use the 24-hour format to set the current time in UTC (GMT).
format)
HH:MM:SS AM or PM
Meter Time GMT, Local Select GMT if you set the current time to Greenwich Mean Time zone. Otherwise,
select Local.
GMT Offset (h) 1 ± HH.0 Available only when Meter Time is set to Local. Set the GMT Offset between ±
00.0 and ± 12.0
To configure the clock using ION Setup, see the section for your meter in the
ION Setup online help or in the ION Setup device configuration guide,
available for download at www.se.com.
1. Currently supports whole integers only.
EAV15107-EN09 35
PowerLogic™ PM5300 series Cybersecurity
Cybersecurity
Cybersecurity overview
This chapter contains up-to-date information about your product’s cybersecurity.
Network administrators, system integrators and personnel that commission,
maintain or dispose of a device should:
• Apply and maintain the device’s security capabilities. See “Device security
capabilities”, page 36 for details.
• Review assumptions about protected environments. See "Protected
environment assumptions", page 37 for details.
• Address potential risks and mitigation strategies. See “Potential Risks and
compensating controls”, page 37 for details.
• Follow recommendations to optimize cybersecurity.
Your device has security capabilities that:
• Allow it to be part of a NERC CIP compliant facility. Go to the North American
Electric Reliability Corporation website for information on NERC Reliability
Standards.
• Align with cybersecurity standards in the IEC 62443 international standard for
business IT systems and Industrial Automation and Control Systems (IACS)
products. Go to the International Electrotechnical Commission website for
information about the IEC62443 international standard.
To communicate a security topic affecting a Schneider Electric product or solution,
go to http://www.se.com/en/work/support/cybersecurity/vulnerability-policy.jsp.
WARNING
POTENTIAL COMPROMISE OF SYSTEM AVAILABILITY, INTEGRITY, AND
CONFIDENTIALITY
• Change default passwords to help prevent unauthorized access to device
settings and information.
• Disable unused ports/services and default accounts, where possible, to
minimize pathways for malicious attacks.
• Place networked devices behind multiple layers of cyber defenses (such as
firewalls, network segmentation, and network intrusion detection and
protection).
• Use cybersecurity best practices (for example: least privilege, separation of
duties) to help prevent unauthorized exposure, loss, modification of data and
logs, interruption of services, or unintended operation.
equipment damage.
Product defense-in-depth
Use a layered network approach with multiple security and defense controls in
your IT and control system to minimize data protection gaps, reduce single-point-
of-failure and create a strong cybersecurity posture. The more layers of security in
your network, the harder it is to breach defenses, take digital assets or cause
disruption.
Device security capabilities
Physical security
Revenue lock icon on the display to determine if the device is revenue locked.
36 EAV15107-EN09
Cybersecurity PowerLogic™ PM5300 series
Multiple anti-tamper sealing points are used to help prevent access and leave
evidence of tampering.
Protected environment assumptions

• Cybersecurity governance – available and up-to-date guidance on governing
the use of information and technology assets in your company.
• Perimeter security – installed devices, and devices that are not in service, are
in an access-controlled or monitored location.
• Emergency power – the control system provides the capability to switch to
and from an emergency power supply without affecting the existing security
state or a documented degraded mode.
• Firmware upgrades – meter upgrades are implemented consistently to the
current version of firmware.
• Controls against malware – detection, prevention and recovery controls to
help protect against malware are implemented and combined with
appropriate user awareness.
• Physical network segmentation – the control system provides the capability
to:
◦ Physically segment control system networks from non-control system
networks.
◦ Physically segment critical control system networks from non-critical
control system networks.
• Logical isolation of critical networks – the control system provides the
capability to logically and physically isolate critical control system networks
from non-critical control system networks. For example, using VLANs.
• Independence from non-control system networks – the control system
provides network services to control system networks, critical or non-critical,
without a connection to non-control system networks.
• Encrypt protocol transmissions over all external connections using an
encrypted tunnel, TLS wrapper or a similar solution.
• Zone boundary protection – the control system provides the capability to:
◦ Manage connections through managed interfaces consisting of
appropriate boundary protection devices, such as: proxies, gateways,
routers, firewalls and encrypted tunnels.
◦ Use an effective architecture, for example, firewalls protecting application
gateways residing in a DMZ.
◦ Control system boundary protections at any designated alternate
processing sites should provide the same levels of protection as that of the
primary site, for example, data centers.
• No public internet connectivity – access from the control system to the
internet is not recommended. If a remote site connection is needed, for
example, encrypt protocol transmissions.
• Resource availability and redundancy – ability to break the connections
between different network segments or use duplicate devices in response to
an incident.
• Manage communication loads – the control system provides the capability to
manage communication loads to mitigate the effects of information flooding
types of DoS (Denial of Service) events.
• Control system backup – available and up-to-date backups for recovery from
a control system failure.
Potential risks and compensating controls

Address potential risks using these compensating controls:
EAV15107-EN09 37
Area Issue Risk Compensating controls
Password through display Default settings are often the If you do not change the default Change the default password of
source of unauthorized access password, unauthorized access 0 (zero) to help reduce
by malicious users. can occur. unauthorized access.
Secure protocols Ethernert port with Modbus TCP If a malicious user gained For transmitting data over an
and BACnet/IP protocols are access to your network, they internal network, physically or
unsecure. could intercept communications. logically segment the network.
The device does not have the For transmitting data over an
capability to transmit encrypted external network, encrypt
data using these protocols. protocol transmissions over all
external connections using an
encrypted tunnel, TLS wrapper
or a similar solution.
Default security settings

Area Setting Default
Communication Modbus TCP Enabled

protocols
BACnet/IP Enabled
Configuration Using the Display Enabled
Display passwords
The device has configurable passwords for the display. Leaving the passwords at
the default values makes it easier for a potential attacker to gain unauthorized
access to your device. It is recommended that you change your passwords from
the default values.
Setting up the display passwords

See Setting up the screen passwords, page 33 for instructions on how to change
the default password.
NOTICE
LOSS OF ACCESS
Failure to follow these instructions can result in data loss and loss of
access to the device.
Harden the device

Recommendations to optimize cybersecurity in a protected environment:
• Harden the device according to your company policies and standards.
• Review assumptions about protected environments and address potential
risks and mitigation strategies. See Product defense-in-depth, page 36 for
details.
• Change the default password. See Display passwords, page 38 for details.
• Disable the BACnet/IP communication protocol when not in use. This reduces
the attack surface. See Configuring BACnet/IP settings using the display,
page 46 for details.
38 EAV15107-EN09
Cybersecurity PowerLogic™ PM5300 series
Enabling/Disabling communication protocols

Disabling unnecessary and unused communication protocols such as BACnet/IP
reduces the attack surface. Changing the port number default values reduces the
predictability of use.
Configuring BACnet/IP settings using the display

See Configuring BACnet/IP settings using the display, page 46 for instructions on
how to enable/disable BACnet/IP configuration on your device using the display.
Firmware upgrades
When device firmware is upgraded – security configuration remains the same until
changed, including usernames and passwords. It is recommended to review
security configuration after an upgrade to analyze privileges for new or changed
device features and revoke or apply them according to your company policies and
standards.
See Firmware upgrades, page 101 for information about firmware upgrades.
Secure disposal guidelines

Use the Secure disposal checklist when disposing a meter to help prevent
potential disclosure of data.
Secure disposal checklist

• Record activities: Document disposal actions according to your company
policies and standards to keep a record of activities.
• Decommission related rules and sanitize records:
◦ Follow decommission and sanitization tasks as described by your
organization or contact your network administrator.
◦ Decommission network and security rules, e.g. a firewall rule that could be
used to get past the firewall.
◦ Perform records tracking sanitization tasks to remove records in related
systems, e.g. monitoring SNMP servers.
• Disposal and reuse: See Disposal, reuse, recycling, page 39 for more
information.
Disposal, reuse, recycling

Before removing the device from its intended environment, follow the Secure
disposal guidelines in this document.
Follow device removal tasks described by your organization or contact your
network administrator to determine a responsible method of disposal.
Dispose the device according to the legislation of the country. Some regulatory
organizations include:
• The United States Environmental Protection Agency (EPA) for guidance on
the sustainable management of electronics.
◦ The EPA provides an Electronic Product Environmental Assessment Tool
(EPEAT) that helps assess the environmental attributes of electronics.
• The European Waste Electrical & Electronic Equipment Directive (WEEE
Directive) is the community directive on waste electrical and electronic
equipment.
EAV15107-EN09 39
• The European Restriction of Hazardous Substances Directive (RoHS)

directive on the restriction of the use of certain hazardous substances in
electrical and electronic equipment.
NOTICE
UNAUTHORIZED OR UNINTENDED ACCESS TO CONFIDENTIAL DATA
• Store devices that are not in service in an access-controlled or monitored
location.
• Physically destroy devices that are decommissioned.
Failure to follow these instructions can result in unauthorized or
unintended access to sensitive or secure customer data.
Device disposal
It is recommended that the entire device is physically destroyed. Destroying the
device helps prevent potential disclosure of data contained in the device that was
not removed.
Device reuse
Store the device in a location that is access controlled or monitored if there is
potential for reuse.
Device recycling
Go to www.se.com and search for the Product Environmental Profile for your
meter type to get instructions on managing e-waste.
40 EAV15107-EN09
Communications PowerLogic™ PM5300 series
Communications
Serial communications
The meter supports serial communication through the RS-485 port.
In an RS-485 network, there is one master device, typically an Ethernet to RS-485
gateway. It provides the means for RS-485 communications with multiple slave
devices (for example, meters). For applications that require only one dedicated
computer to communicate with the slave devices, a USB to RS-485 converter can
be used to connect to the master device.
Up to 32 devices can be connected on a single RS-485 bus.
RS-485 network configuration

After you have wired the RS-485 port and powered up the meter, you must
configure the serial communications port in order to communicate with the meter.
Each device on the same RS-485 communications bus must have a unique
address and all connected devices must be set to the same protocol, baud rate,
and parity (data format).
NOTE: To communicate with the meter using ION Setup, you must set the
serial site and all connected devices in the RS-485 network to the same parity
setting.
For meters that do not have a display, you must first wire and configure each one
separately before connecting these meters to the same RS-485 bus.
RS-485 port setup

The meter is factory-configured with default serial communications settings that
you may need to modify before connecting the meter to the RS-485 bus.
The meter is factory-configured with the following default serial communications
settings:
• Protocol = Modbus RTU
• Address = 1
• Baud rate = 19200
• Parity = Even
You can use a communications converter (USB to RS-485 or RS-232 to RS-485)
or Ethernet gateway device to connect to the meter.
Setting up serial communications using the display

The Serial Port setup screen allows you to configure the meter’s RS-485
communications port so you can use software to access the meter’s data or
configure the meter remotely.
3. Navigate to Comm > Serial.
Edit.
EAV15107-EN09 41
PowerLogic™ PM5300 series Communications
7. Press the up arrow to exit. Press Yes to save your changes.
Protocol Modbus Select the communications format used to transmit

data. The protocol must be the same for all devices in a
communications loop.
Address 1 to 247 Set the address for this device. The address must be
unique for each device in a communications loop. For
Jbus protocol, set the device ID to 255.
Baud Rate 9600, 19200, Select the speed for data transmission. The baud rate
38400 must be the same for all devices in a communications
loop
Parity Even, Odd, Select None if the parity bit is not used. The parity
None setting must be the same for all devices in a
communications loop.
Ethernet communications
The meter uses Modbus TCP and BACnet/IP protocols to communicate at data
speeds up to 100 Mbps through its Ethernet communications port (if available).
The meter supports a maximum of 128 concurrent TCP/IP connections.
Ethernet configuration
In order to use Ethernet communications, you must configure your device’s IP
address; you must also configure the subnet and gateway information if required
by your network.
You need to enter network information for any Ethernet servers used by the
device.
NOTE: Contact your network system administrator for your IP address and
other Ethernet network configuration values.
Configure your device’s Ethernet settings by using the display. Modify your
meter’s Ethernet settings to those provided by your network system administrator
before connecting the device to your local area network (LAN).
After the meter’s Ethernet port is configured and connected to the LAN, you can
use ION Setup to configure other meter setup parameters.
Ethernet port setup

The meter is factory-configured with default Ethernet communications settings.
You must modify the default Ethernet settings before connecting the meter to your
local area network (LAN).
The default Ethernet communications settings are:
• IP address = 169.254.0.10
• Subnet mask = 255.255.0.0
• Gateway = 0.0.0.0
• Device name = PM53-#xxxxxxxxxx, where xxxxxxxxxx is the meter’s factory
serial number (with leading zeros if serial number is less than 10 characters)
• IP method = Default
Setting up Ethernet communications using the display

The Ethernet setup screen allows you to assign the meter a unique IP address so
you can use software to access the meter’s data or configure the meter remotely
through the Ethernet port.
42 EAV15107-EN09
Before configuring the Ethernet parameters, make sure you obtain your meter’s IP
address information from your network administrator or IT department.
3. Navigate to Comm > Enet.
Edit.
IP Method Stored, Default, This controls the network protocol for your device (what
DHCP, BOOTP the meter uses to obtain its IP address).
Stored: Use the static value programmed in the IP

Address setup register
Default: Use 169.254 as the first two values of the IP

address, then convert the last two hexadecimal values
of the MAC address to decimal and use this as the last
two values of the IP address. Example:
MAC address = 00:80:67:82:B8:C8
Default IP = 169.254.184.200
DHCP: Dynamic Host Configuration Protocol
BOOTP: Bootstrap Protocol
IP Address Contact your The Internet protocol address of your device.

local network
administrator for
parameter
values.
Subnet Contact your The Ethernet IP subnetwork address of your network
local network (subnet mask).
administrator for
parameter
values.
Gateway Contact your The Ethernet IP gateway address of your network.
local network
administrator for
parameter
values.
Device Name N/A This parameter is read-only for reference purposes.
BACnet/IP
BACnet/IP protocol allows communication between the components of a building
automation and control system (for example, HVAC, lighting control, security
systems and related equipment).
The BACnet/IP protocol defines a number of services that are used to
communicate between devices and the objects that are acted upon by those
services.
EAV15107-EN09 43
Term Definition
APDU Application protocol data unit, that data portion of a BACnet
message.
Confirmed message A message for which the device expects an answer.
COV, COV increment Change of value, sets the amount by which a value has to change in
order for the meter to send a subscription notification.
Device A BACnet device is a unit that is designed to understand and use

BACnet protocol (for example, a BACnet-enabled meter or software
program). It contains information about the device and device data in
objects and object properties. Your meter is a BACnet device.
Object Represents the device and device data. Each object has a type (for
example, analog input or binary input) and has a number of
properties.
Present value The current value of an object.
Property The smallest piece of information in BACnet communications, it

consists of a name, data type and value.
Service Messages from one BACnet device to another.
Subscription A relationship between a BACnet client and the meter, so that when
the present value property of an object changes on the meter, a
notification is sent to the client.
Subscription notification The message the meter sends to indicate a COV event has occurred.
Unconfirmed message A message for which the device does not expect an answer.
BACnet Broadcast A BACnet/IP device (or software application) residing on a BACnet/

Management Device IP subnet that forwards BACnet broadcast messages from devices
(BBMD) on its subnet to peer BBMDs and registered foreign devices on other
subnets.
Foreign device A BACnet/IP device (or software application) that resides on a
remote IP subnet and registers with a BBMD to facilitate the sending
and receiving of broadcast messages to/from devices accessible by
the BBMD.
Supported BACnet features

PM5320, PM5340 and PM5341 meters support specific BACnet components and
standard objects over Ethernet. The supported BACnet features are available in
applicable products with firmware version 2.00 and above.
The meter’s BACnet/IP protocol support is certified by BACnet International. Go to
www.bacnetinternational.org or www.se.com and search for your meter model to
access the PICS (Protocol Implementation Conformance Statement) for your
meter.
Supported BACnet components
BACnet component Description
Protocol version 1
Protocol revision 14
Standardized device profile (Annex L) BACnet Application Specific Controller (B-ASC)
BACNet Interoperability Building Blocks (Annex K) • DS-RP-B (Data Sharing - Read Property - B)
• DS-RPM-B (Data Sharing - Read Property Multiple - B)
• DS-WP-B (Data Sharing - Write Property - B)
• DS-WPM-B (Data Sharing - Write Property Multiple - B)
• DS-COV-B (Data Sharing - COV - B)
• DM-DDB-B (Device Management - Dynamic Device Binding - B)
• DM-DOB-B (Device Management - Dynamic Object Binding - B)
• DM-DCC-B (Device Management - Device Communication Control - B)
BACnet/IP (Annex J) BACnet communication internet protocol
44 EAV15107-EN09
BACnet component Description
Data link layer options UDP
Character set ANSI X3.4/UTF-8

Supported services • subscribeCOV
• readProperty
• readPropertyMultiple
• writeProperty
• writePropertyMultiple
• deviceCommunicationControl
• who-HAS
• who-Is
• I-Am
• I-Have
• Confirmed COV notification
• Unconfirmed COV notification
Segmentation The meter does not support segmentation
Static device address binding The meter does not support static device address binding
Networking options The meter supports registration as a foreign device
Supported standard object types

NOTE: The BACnet protocol allows you to set the out-of-service property of
an object to true and write a value to that property for testing purposes. In this
case, your BACnet software displays the value you wrote to the object, not the
actual value from the meter and the system it is monitoring. Make sure you set
the out-of-service property of all objects to false before you put the meter into
service.
Object type Optional properties Writeable properties Conditional writeable

supported supported properties supported
Device Object • Location • Object_Name —

• Description • Object_Identifier
• Local_Time • Location
• Local_Date • Description
• Active_COV_ • APDU_Timeout
Subscriptions
• Number_Of_APDU_
• Profile_Name Retries
Analog Input Object • Description • Out_Of_Service Present_Value

• Reliability • COV_Increment
• COV_Increment
Binary Input Object • Description Out_Of_Service Present_Value

• Reliability
Multi-state Input Object • Description Out_Of_Service Present_Value

• Reliability
• State_Text
BACnet/IP communications implementation

Your meter's BACnet implementation includes specific behaviors and
configuration.
EAV15107-EN09 45
Basic configuration for BACnet communications

Before communicating with the meter via BACnet protocol, make sure the basic
BACnet settings are configured appropriately for your network. The Device ID
must be unique in your BACnet IP network.
Change of Value (COV) subscriptions

The meter supports up to 20 COV subscriptions. You can add COV subscriptions
to Analog Input, Binary Input and Multi-state Input objects using your BACnet-
compatible software.
Configuring BACnet/IP settings using the display

Use the meter’s display to configure BACnet/IP settings if required.
2. Enter the setup password (default is “0”),then press OK.
3. Navigate to Comm > BACnet.
Edit.
Basic BACnet/IP settings available using the display
BACnet Status Enabled, Disabled Enable or disable BACnet/IP communications with the meter
Device ID 0 – 4194302 Enter the ID of the meter on your BACnet network. The ID must be
unique on the network.
UDP Port 1024 – 65535 Enter the port the meter uses for BACnet/IP communications. The
default is the standard BACnet/IP port (47808).
Foreign device settings available using the display
BBMD Status Enabled, Disabled Enable or disabled registration of the meter as a foreign device.
BBMD IP Contact your local network Enter the IP address of the BACnet/IP Broadcast Management
administrator for parameter Device (BBMD), if you use a BBMD on your network.
values.
BBMD Port 1024 – 65535 Enter the port number that is used for communications with the
BBMD. The default is the standard BACnet/IP port (47808)
BBMD TTL (sec) 0 – 65535 The length of time (in seconds) the BBMD keeps an entry for this
device in its foreign device table.
BACnet objects
Device object
Your meter has a Device object which describes the meter to the BACnet network.
The following table outlines the properties of the Device object, whether a property
is read-only or read-write, and if the value of the property is stored in the meter’s
nonvolatile onboard memory.
46 EAV15107-EN09
Device object property R/W Stored Possible values Description
Object_Identifier R/W Y See description The unique device ID number for the meter, in
the format of <device, #>.
The meter ships from the factory with a device

ID equal to the last 6 digits of the serial
number.
Object_Name R/W Y See description A configurable name for the meter.
The meter ships from the factory with a name

of <model name>_<serial number> (for
example, PM5320_0000000000).
Object_Type R — Device The object type for the meter.
System_Status R — Operational This value of this property is always

Operational.
Vendor_Name R — Schneider Electric Meter manufacturer
Vendor_Identifier R — 10 The BACnet vendor identifier for Schneider

Electric.
Model_Name R — varies Device model (for example, PM5320) and
serial number in the format <model name>_
<serial number> (for example, PM5320_
0000000000).
Firmware_Revision R — varies BACnet firmware version, stored in an x.x.x

format (for example, 1.9.0).
Application_Software_Version R — varies Meter firmware version, stored in an x.x.x

format (for example, 1.0.305).
Description R/W Y configurable Optional description of the meter, limited to 64

characters.
Location R/W Y configurable Optional description of the meter’s location,
limited to 64 characters.
Protocol_Version R — varies BACnet protocol version (for example, version
1)
Protocol_Revision R — varies BACnet protocol revision (for example,

revision 14)
Protocol_Services_Supported R — 0000 0100 0000 1011 The BACnet services supported by the meter:
1100 1000 0000 0000 subscribeCOV, readProperty,
0110 0000 0 readPropertyMultiple, writeProperty,
writePropertyMultiple,
deviceCommunicationControl,
ReinitializeDevice, who-HAS, who-Is
Protocol_Object_Types_ R — 1001 0000 1000 0100 The BACnet object types supported by the
Supported 0000 0000 0000 0000 meter: analog input, binary input, multi-state
0000 0000 0000 0000 input, device.
0000 000
Object_list R — See description List of objects in the meter.
Max_APDU_Length_Accepted R — 1476 The maximum packet size (or application

protocol data unit) that the meter can accept,
in bytes.
Segmentation_Supported R — 0x03 The meter does not support segmentation.
Local_Date R — varies Current date on the meter

NOTE: Use the display or ION Setup to
set the meter’s date.
Local_Time R — varies Current time on the meter
NOTE: Use the display or ION Setup to
set the meter’s time.
APDU_Timeout R/W Y 1000 – 30000 The amount of time (in milliseconds) before
the meter tries to resend a confirmed message
that has not been answered.
Number_Of_APDU_Retries R/W Y 1 – 10 The number of times the meter tries to resend
an unanswered confirmed request.
Device_Address_Binding R — — Device address binding table is always blank

because the meter does not initiate the who-Is
service.
EAV15107-EN09 47
Device object property R/W Stored Possible values Description
Database_Revision R Y varies A number that increments when the object

database on the meter changes (for example,
when an object is created or deleted or the ID
of an object changes).
Active_COV_Subscriptions R — varies List of COV subscriptions currently active on

the meter.
Profile_Name R — varies Device identifier that records the meter
manufacturer, the meter family and the
specific meter model (for example, 10-
PM5000-PM5320).
Analog Input objects

Your meter has a number of Analog Input objects that provide meter values and
information on meter settings.
The following tables list the Analog Input objects along with the units and default
COV value for each object (if applicable).
Real-time measurements
Object ID Object name Units Default COV Description
3000 Current - Ph A A 50 Current phase A
3002 Current - Ph B A 50 Current phase B
3004 Current - Ph C A 50 Current phase C
3006 Current - Neutral A 50 Neutral current

3008 Current - Ground A 50 Ground current
3010 Current - Avg A 50 Current average
3012 Current Unb - Ph A % 20 Current unbalance phase A
3014 Current Unb - Ph B % 20 Current unbalance phase B
3016 Current Unb - Ph C % 20 Current unbalance phase C
3018 Current Unb - Worst % 20 Current unbalance worst
3020 Voltage - A-B V 10 Voltage A-B
3022 Voltage - B-C V 10 Voltage B-C
3024 Voltage - C-A V 10 Voltage C-A
3026 Voltage - Avg L-L V 10 Voltage L-L Avg
3028 Voltage - A-N V 10 Voltage A-N
3030 Voltage - B-N V 10 Voltage B-N
3032 Voltage - C-N V 10 Voltage C-N
3036 Voltage - Avg L-N V 10 Voltage L-N Avg
3038 Voltage Unb - A-B % 20 Voltage unbalance A-B
3040 Voltage Unb - B-C % 20 Voltage unbalance B-C
3042 Voltage Unb - C-A % 20 Voltage unbalance C-A
3044 Voltage Unb - Worst L-L % 20 Voltage unbalance L-L worst
3046 Voltage Unb - A-N % 20 Voltage unbalance A-N
3048 Voltage Unb - B-N % 20 Voltage unbalance B-N
3050 Voltage Unb - C-N % 20 Voltage unbalance C-N
3052 Voltage Unb - Worst L-N % 20 Voltage unbalance L-N worst
3110 Frequency Hz 10 Frequency
48 EAV15107-EN09
Power and power factor
3054 Active Power - Ph A kW 10 Active power phase A
3056 Active Power - Ph B kW 10 Active power phase B
3058 Active Power - Ph C kW 10 Active power phase C
3060 Active Power - Total kW 10 Active power total
3062 Reactive Power - Ph A kVAR 10 Reactive power phase A
3064 Reactive Power - Ph B kVAR 10 Reactive power phase B
3066 Reactive Power - Ph C kVAR 10 Reactive power phase C
3068 Reactive Power - Total kVAR 10 Reactive power total
3070 Apparent Power - Ph A kVA 10 Apparent power phase A
3072 Apparent Power - Ph B kVA 10 Apparent power phase B
3074 Apparent Power - Ph C kVA 10 Apparent power phase C
3076 Apparent Power - Total kVA 10 Apparent power total
3078 Power Factor - Ph A — 0.2 Power factor phase A
3080 Power Factor - Ph B — 0.2 Power factor phase B
3082 Power Factor - Ph C — 0.2 Power factor phase C
3084 Power Factor - Total — 0.2 Power Factor Total
Energy and energy by tariff measurements
2700 Active Energy Delvd kWh 100 Active energy delivered
2702 Active Energy Rcvd kWh 100 Active energy received
2704 Active Energy Delvd + Rcvd kWh 100 Active energy delivered + received
2706 Active Energy Delvd - Rcvd kWh 100 Active energy delivered – received
2708 Reactive Energy Delvd kVARh 100 Reactive energy delivered
2710 Reactive Energy Rcvd kVARh 100 Reactive energy received
2712 Reactive Energy Delvd + Rcvd kVARh 100 Reactive energy delivered +
received
2714 Reactive Energy Delvd - Rcvd kVARh 100 Reactive energy delivered –
received
2716 Apparent Energy Delvd kVAh 100 Apparent energy delivered
2718 Apparent Energy Rcvd kVAh 100 Apparent energy received
2720 Apparent Energy Delvd + Rcvd kVAh 100 Apparent energy delivered +
received
2722 Apparent Energy Delvd - Rcvd kVAh 100 Apparent energy delivered –
received
4191 Applicable Tariff Energy Rate — 1 Denotes the active tariff:
0 = Multi Tariff feature is disabled
1 = tariff 1 active
2 = tariff 2 active
3 = tariff 3 active
4 = tariff 4 active
4800 Active Energy Delvd (Tariff 1) kWh 100 Tariff 1 active energy import
EAV15107-EN09 49
Power demand
3764 Dmd - Active Power Last kW 10 Demand - Active power last
3766 Dmd - Active Power Present kW 10 Demand - Active power present
3768 Dmd - Active Power Pred kW 10 Demand - Active power predicted
3770 Dmd - Active Power Peak kW 10 Demand - Active power peak
3780 Dmd - Reactive Power Last kVAR 10 Demand - Reactive power last
3782 Dmd - Reactive Power Present kVAR 10 Demand - Reactive power present
3784 Dmd - Reactive Power Pred kVAR 10 Demand - Reactive power predicted
3786 Dmd - Reactive Power Peak kVAR 10 Demand - Reactive power peak
3796 Dmd - Apparent Power Last kVA 10 Demand - Apparent power last
3798 Dmd - Apparent Power Present kVA 10 Demand - Apparent power present
3800 Dmd - Apparent Power Pred kVA 10 Demand - Apparent power

predicted
3802 Dmd - Apparent Power Peak kVA 10 Demand - Apparent power peak
Current demand
3876 Dmd - Average Current Last A 10 Demand - Average current last
3878 Dmd - Avg Current Present A 10 Demand - Average current present
3880 Dmd - Average Current Pred A 10 Demand - Average current

predicted
3882 Dmd - Average Current Peak A 10 Demand - Average current peak
Power quality
21300 THD Current - Ph A % 20 THD Current A

21302 THD Current - Ph B % 20 THD Current B
21304 THD Current - Ph C % 20 THD Current C
21306 THD Current - Ph N % 20 THD Current N
21308 THD Current - Ph G % 20 THD Current G
21310 thd Current - Ph A % 20 thd Current A

21312 thd Current - Ph B % 20 thd Current B
21314 thd Current - Ph C % 20 thd Current C
21316 thd Current - Ph N % 20 thd Current N
21318 thd Current - Ph G % 20 thd Current G

21320 Total Dmd Distortion % 20 Total Demand Distortion
21322 THD Voltage - A-B % 20 THD Voltage A-B
21324 THD Voltage - B-C % 20 THD Voltage B-C
50 EAV15107-EN09
21326 THD Voltage - C-A % 20 THD Voltage C-A
21328 THD Voltage - Avg L-L % 20 THD Voltage L-L
21330 THD Voltage - A-N % 20 THD Voltage A-N
21332 THD Voltage - B–N % 20 THD Voltage B-N
21334 THD Voltage - C-N % 20 THD Voltage C-N
21338 THD Voltage - Avg L-N % 20 THD Voltage L-N
21340 thd Voltage - A-B % 20 thd Voltage A-B
21342 thd Voltage - B-C % 20 thd Voltage B-C
21344 thd Voltage - C-A % 20 thd Voltage C-A
21346 thd Voltage - Avg L-L % 20 thd Voltage L-L
21348 thd Voltage - A-N % 20 thd Voltage A-N
21350 thd Voltage - B-N % 20 thd Voltage B-N
21352 thd Voltage - C-N % 20 thd Voltage C-N
21356 thd Voltage - Avg L-N % 20 thd Voltage L-N
Meter information
The following table lists Analog Input objects that provide information about the
meter and its configuration.
NOTE: You can access the meter’s configuration information over BACnet
communications. However, you must use the display or ION Setup to
configure the meter’s settings.
2000 Time since last meter power up Seconds 604800 Time since the meter was last
powered up
2004 Meter operation timer Seconds 604800 Total meter operation time
2014 Number of phases — 1 Number of phases
1, 3
2015 Number of wires — 1 Number of wires
2, 3, 4
2017 Nominal frequency Hz 1 Nominal frequency
50, 60
2025 Number of VTs — 1 Number of VTs
0, 2, 3
2026 VT primary V 1 VT Primary
2028 VT secondary V 1 VT Secondary
2029 Number of CTs — 1 Number of CTs
1, 2, 3
2030 CT primary A 1 CT Primary
2031 CT secondary A 1 CT Secondary
Binary Input objects

Your meter has a number of Binary Input objects that provide the status
information from the meter’s I/O.
EAV15107-EN09 51
The following table lists the Binary Input (BI) objects available on the meter.
Object ID Object name Description
38416, 38417 Digital Input 1 Status of digital inputs 1 and 2:
Digital Input 2 0 = on
1 = off
NOTE: This information only applies if the digital input is
configured as a status input.
38448, 38449 Digital Output 1 Status of digital outputs:

0 = on
Digital Output 2
1 = off
Multi-state Input objects

Your meter has a number of Multi-state Input objects that provide information
about the meter’s I/O and power system settings.
Meter configuration multi-state input objects
Object ID Object name Object name / description
2016 Power System Type Power system configuration:

0 = 1PH2W L-N
1 = 1PH2W L-L
2 = 1PH3W L-L with N
3 = 3PH3W ungrounded delta
4 = 3PH3W corner grounded delta
5 = 3PH3W ungrounded wye
6 = 3PH3W grounded wye
7 = 3PH3W resistance grounded wye
8 = 3PH4W center-tapped open delta
9 = 3PH4W center-tapped delta
10 = 3PH4W ungrounded wye
11 = 3PH4W grounded wye
12 = 3PH4W resistance grounded wye
2036 VT Connection Type VT connection type:

0 = Direct connect
1 = Delta (2 VT)
2 = Wye (3 VT)
3 = L-N (1 VT)
4 = L-L (1 VT)
5 = L-L with N (2 VT)
3701 Demand Method - Power Power demand method:

0 = Thermal demand
1 = Timed interval sliding block
2 = Timed interval block
3 = Timed interval rolling block
4 = Input synchronized block
5 = Input synchronized rolling block
6 = Command synchronized block
7 = Command synchronized rolling block
8 = Clock synchronized block
9 = Clock synchronized rolling block
52 EAV15107-EN09
Object ID Object name Object name / description
3711 Demand Method - Current Current demand method:

0 = Thermal demand
3721 Demand Method - Input Metering Input metering demand method:

0 = Thermal demand
I/O multi-state input objects

The following table lists the Multi-state Input objects that provide information about
meter’s I/O configuration.
Object ID Object name Description
7274, 7298 Digital Input 1 Mode Digital input control mode

0 = Normal (Alarm)
Digital Input 2 Mode
1 = Demand Interval Sync Pulse
2 = Multi-tariff Control
9673, 9681 Digital Output Mode 1 Digital output 1 and 2 control mode
0 = External
Digital Output Mode 2
1 = Demand Sync
2 = Alarm
3 = Energy
EAV15107-EN09 53
PowerLogic™ PM5300 series Logging
Logging
Data log
The meter has an alarm log and data logging for selected values.
Logs are stored in the non-volatile memory of the meter and are referred to as on-
board logs. The data log is disabled from the factory.
Setting up the data log

You can select the items to record in the data log and the frequency (logging
interval) that you want those values updated
Use ION Setup to configure data logging.
NOTICE
DATA LOSS
Save the contents of the data log before configuring it.
1. Start ION Setup and open your meter in setup screens mode (View > Setup
Screens). See the ION Setup Help for instructions.
2. Double-click Data Log #1.
3. Set up the logging frequency and measurements/data to log.
4. Click Send to save the changes to the meter.
Status Enable, Disable Set this parameter to enable

or disable data logging in the
meter.
Interval 15 minutes, 30 minutes, 60 Select a time value to set the
minutes logging frequency.
Channels Items available for logging Select an item to record from

can vary based on the meter the “Available” column, then
type. click the double-right arrow
button to move the item to
the “Selected” column.
To remove an item, select it

from the “Selected” column
then click the double-left
arrow button.
Saving the data log contents using ION Setup

You can use ION Setup to save the contents of the data log.
1. Start ION Setup and open your meter in data screens mode (View > Data
Screens. See the ION Setup help for instructions.
2. Double-click Data Log #1 to retrieve the records.
3. Once the records have finished uploading, right-click anywhere in the viewer
and select Export CSV from the popup menu to export the entire log.
NOTE: To export only selected records in the log, click the first record you
want to export, hold down the SHIFT key and click the last record you
want to export, then select Export CSV from the popup menu.
54 EAV15107-EN09
Logging PowerLogic™ PM5300 series
4. Navigate to the folder where you want to save the data log file, then click
Save.
Alarm log
The meter can log the occurrence of any alarm condition.
Each time an alarm occurs it is entered into the alarm log. The alarm log in meter
stores the pickup and dropout points of alarms along with the date and time
associated with these alarms.
Alarm log storage

The power and energy meter stores alarm log data in non-volatile memory.
The size of the alarm log is fixed at 40 records.
Memory allocation for log files

Each file in the meter has a maximum memory size.
Memory is not shared between the different logs, so reducing the number of
values recorded in one log does not allow more values to be stored in different log.
Log type Maximum records stored Storage (bytes)
Alarm Log 40 2,200
Data Log 5760 256k
EAV15107-EN09 55
PowerLogic™ PM5300 series Inputs / outputs
Inputs / outputs
Available I/O ports
The meter is equipped with status inputs, digital outputs and relay outputs.
DANGER
standards.
is off.
otherwise.
• Do not use this device for critical control or protection of persons, animals,
property or equipment.
• Replace all devices, doors and covers before turning on power to this
equipment.
After you wire the meter’s I/O ports, you can configure these ports so you can use
the meter to perform I/O functions.
Models Status input ports1 Digital output ports2 Relay output ports
PM5310 2 (S1+, S2+) 2 (D1+, D2+) —
PM5320 2 (S1+, S2+) 2 (D1+, D2+) —
PM5330 2 (S1+, S2+) 2 (D1+, D2+) 2 (Relay 1, Relay 2)
PM5331
PM5340
PM5341
1The meter’s status inputs require an external voltage source to detect the status input’s on/off
state. The meter detects an ON state if the external voltage appearing at the status input is within its
operating range. The external voltage can be derived from either the whetting output provided by
the meter or by a voltage source up to 36 V DC external to the meter.
2The digital outputs can handle voltages less than 40 V DC. For higher voltage applications, use an
external relay in the switching circuit.
Status input applications

Status inputs are typically used for monitoring the status of external contacts or
circuit breakers.
Status input wiring considerations

The meter’s status inputs require an external voltage source to detect the status
input’s on/off state.
56 EAV15107-EN09
Inputs / outputs PowerLogic™ PM5300 series
The meter detects an ON state if the external voltage appearing at the status input
is within its operating range. The external voltage can be derived from either the
whetting output provided by the meter or by a voltage source up to 36 V DC
external to the meter.
Configuring status inputs using the display

The status input ports (S1 and S2) can be configured using the display.
NOTE: It is recommended you use ION Setup to configure the status inputs,
as setup parameters that require text entry can only be modified using ION
Setup.
3. Navigate to I/O > S In.
4. Move the cursor to point to the status input you want to set up, then press
Edit.
Edit.
NOTE: If Edit is not displayed, it means the parameter is either read-only
or can only be modified through software.
Label — This can be modified only

through software. Use this
field to assign names to the
status inputs (S1 and S2).
Debounce Time (ms) 0 to 1000 Debounce is the time delay

that compensates for
mechanical contact bounce.
Use this field to set how long
(in milliseconds) the external
signal must remain in a
certain state to be
considered a valid state
change.
Control Mode Normal This field displays how the

status input functions.
Normal: the status input is

not associated with another
meter function. The meter
counts and records the
number of incoming pulses
normally.
Configuring status inputs using ION Setup

The status input ports (S1 and S2) can be configured using ION Setup.
1. Start ION Setup.
2. Connect to your meter.
3. Navigate to I/O configuration > I/O Setup.
4. Select a status input to configure and click Edit.
The setup screen for that status input is displayed.
EAV15107-EN09 57
5. Enter a descriptive name for the status input’s Label.

6. Configure the other setup parameters as required.
7. Click Send to save your changes.
Status input setup parameters available through ION Setup
Label — Use this field to change the default label and assign a descriptive name to this
status input.
Control Mode Normal, Demand Sync, Input This field displays how the status input functions.
Metering • Normal: the status input is not associated with another meter function. The
meter counts and records the number of incoming pulses normally.
• Demand Sync: the status input is associated with one of the input sync
demand functions. The meter uses the incoming pulse to synchronize its
demand period with the external source.
• Input Metering: the status input is associated with one of the input metering
channels. The meter counts and records the number of incoming pulses and
related consumption data associated with the pulses.
Debounce 0 to 9999 Debounce is the time delay that compensates for mechanical contact bounce. Use
this field to set how long (in milliseconds) the external signal must remain in a
certain state to be considered a valid state change.
Associations — This field displays additional information if the status input is already associated
with another meter function.
Digital output applications

Digital outputs are typically used in switching applications, for example, to provide
on/off control signals for switching capacitor banks, generators, and other external
devices and equipment.
The digital output can also be used in demand synchronization applications,
where the meter provides pulse signals to the input of another meter to control its
demand period. The digital output can also be used in energy pulsing applications,
where a receiving device determines energy usage by counting the kWh pulses
coming from the meter’s digital output.
The digital outputs on the meter are internally designed using solid-state devices
with an open-collector configuration. These outputs must be connected to the
specified power supply with a current limiter to function. Refer to the digital output
application example below for more information.
Digital output application example

You can connect one of your meter’s digital outputs to a relay that switches on a
generator and the other digital output to send a demand sync pulse to other
meters.
In the following example, the first meter (Meter 1) controls and sets the demand
period (900 seconds) of the other meters (Meter 2, Meter 3, Meter 4) through the
output pulse occurring at the end of the first meter’s demand interval.
A Relay
Meter 1
D1 D2 S1 S2 -/C +
B Demand period (in this example,
900 seconds)
Power + < 20 mA
source
< 20 mA
< 40 V DC
-
Meter 2 Meter 3 Meter 4
58 EAV15107-EN09
Configuring digital outputs using the display

You can use the display to configure the digital outputs.
NOTE: It is recommended you use ION Setup to configure the digital outputs,
as setup parameters that require text entry can only be modified using
software.
3. Navigate to I/O > D Out.
4. Move the cursor to point to the digital output you want to set up, then press
Edit.
5. Edit the parameters as required.
a. Move the cursor to point to the parameter you want to modify, then press
Edit
b. Modify the parameter as required, then press OK.
c. Move the cursor to point to the next parameter you want to modify, press
Edit, make your changes, then press OK.
Digital output setup parameters available through the display
Setting Option or range Description
Label — This can be modified only through software. Use this field to change the default label
and assign a descriptive name to this digital output.
Control Mode External, Demand Sync, This field displays how the digital output functions.
Alarm, Energy • External: the digital output is controlled remotely either through software or by a
PLC using commands sent through communications.
• Demand Sync: the digital output is associated with one of the demand systems.
The meter sends a pulse to the digital output port at the end of every demand
interval.
• Alarm: the digital output is associated with the alarm system. The meter sends a
pulse to the digital output port when the alarm is triggered.
• Energy: The digital output is associated with energy pulsing. When this mode is
selected, you can select the energy parameter and the set the pulse rate (p/k_h).
Behavior Mode Normal, Timed, Coil Hold • Normal: this mode applies when control mode is set to External or Alarm. In the
event of trigger for External mode, the digital output remains in the ON state until
an OFF command is sent by the computer or PLC. In the event of trigger for Alarm
mode, the digital output remains in the ON state until the drop out point is crossed.
• Timed: the digital output remains ON for the period defined by the On Time setup
register.
• Coil Hold: this mode applies when control mode is set to External or Alarm. For a
unary alarm that is associated with a digital output, you must set Behavior Mode to
Coil Hold. The output turns on when the “energize” command is received and turns
off when the “coil hold release” command is received. In the event of a control
power loss, the output remembers and returns to the state it was in when control
power was lost.
On Time (s) 0 to 9999 This setting defines the pulse width (ON time) in seconds.
NOTE: In energy mode, the digital output pulse ON time is fixed for 20 ms.
Select Dmd Power, Current Applies when Control Mode is set to Demand Sync. Select the demand system to
System monitor.
Select Alarms All available alarms Applies when Control Mode is set to Alarm. Select one or more alarms to monitor.
Configuring digital outputs using ION Setup

You can use ION Setup to configure the digital outputs.
EAV15107-EN09 59
1. Start ION Setup.

3. Configure the control mode you want to use for the digital output.
Option Description
External or Energy Pulsing 1. Navigate to I/O configuration > Energy Pulsing.

2. Select the digital output you are configuring and click Edit.
3. Select External or Energy from the Control dropdown list.
4. For Energy, configure the energy pulsing parameters as required.
Alarm 1. Navigate to Alarming.

2. Select the alarm type of the alarm you want to associate with the digital output and click Edit.
3. Configure the alarm parameters as required.
4. Select the digital output you want to associate with the alarm.
NOTE: You may need to enable the alarm before you can associate the digital output.
Demand 1. Navigate to Demand Setup.

2. Select the demand type that you want to associate with the digital output and click Edit.
3. Configure the demand mode parameters as required.
4. Click the Digital Output Association button to associate a digital output.

5. Select a digital output to configure and click Edit.
The setup screen for that digital output is displayed.
6. Enter a descriptive name for the digital output in the Label field.
60 EAV15107-EN09
Digital output setup parameters available using ION Setup
Label — Use this field to change the default label and assign a descriptive name to this digital
output.
Control Mode External, Demand, This field displays how the digital output functions.
Alarm, Energy
• External: the digital output is controlled remotely either through software or by a
PLC using commands sent through communications.
• Demand: the digital output is associated with one of the demand systems. The
meter sends a pulse to the digital output port at the end of every demand interval.
• Alarm: the digital output is associated with the alarm system. The meter sends a
pulse to the digital output port when the alarm is triggered.
• Energy: The digital output is associated with energy pulsing. When this mode is
selected, you can select the energy parameter and the set the pulse rate (pulses/
kW).
Behavior Mode Normal, Timed, Coil Hold • Normal: this mode applies when control mode is set to External or Alarm. In the
event of trigger for External mode, the digital output remains in the ON state until
an OFF command is sent by the computer or PLC. In the event of trigger for
Alarm mode, the digital output remains in the ON state until the drop out point is
crossed.
• Timed: the digital output remains ON for the period defined by the On Time setup
register.
• Coil Hold: this mode applies when control mode is set to External or Alarm. For a
unary alarm that is associated with a digital output, you must set Behavior Mode
to Coil Hold. The output turns on when the “energize” command is received and
turns off when the “coil hold release” command is received. In the event of a
control power loss, the output remembers and returns to the state it was in when
control power was lost.
On Time (s) 0 to 9999 This setting defines the pulse width (ON time) in seconds.
NOTE: In energy mode, the digital output pulse ON time is fixed for 20 ms.
Select Dmd System Power, Current Applies when Control Mode is set to Demand Sync. Select the demand system to
monitor.
Select Alarms All available alarms Applies when Control Mode is set to Alarm. Select one or more alarms to monitor.
Associations — This field displays additional information if the digital output is already associated with
another meter function.
Relay output applications

Relay outputs can be configured to be used in switching applications, for example,
to provide on/off control signals for switching capacitor banks, generators, and
other external devices and equipment.
Configuring relay outputs using the display

You can use the front panel to configure the relay outputs.
NOTE: It is recommended you use ION Setup to configure the relay outputs,
as setup parameters that require text entry can only be modified using
software.
3. Navigate to I/O > Relay.
4. Move the cursor to point to the relay output you want to set up, then press
Edit.
EAV15107-EN09 61
Edit.
8. Press the up arrow to exit, then press Yes to save your changes.
Relay output setup parameters available through the display
Label — Use this field to change the default label and assign a
descriptive name to this relay output.
Control Mode External, Alarm This field displays how the relay output functions.
• External: the relay output is controlled remotely
either through software or by a PLC using
commands sent through communications.
• Alarm: the relay output is associated with the
alarm system. The meter sends a pulse to the
relay output port when the alarm is triggered.
Behavior Mode Normal, Timed, Coil Hold • Normal: this mode applies when control mode is
set to External or Alarm. In the event of trigger
for External mode, the relay output remains in
the closed state until an open command is sent
by the computer or PLC. In the event of trigger
for Alarm mode, the relay output remains in the
closed state until the drop out point is crossed.
• Timed: the relay output remains ON for the
period defined by the On Time setup register.
• Coil Hold: this mode applies when control mode
is set to External or Alarm. For a unary alarm
that is associated with a relay output, you must
set Behavior Mode to Coil Hold. The output
turns on when the “energize” command is
received and turns off when the “coil hold
release” command is received. In the event of a
control power loss, the output remembers and
returns to the state it was in when control power
was lost.
On Time (s) 0 to 65535 This setting defines the pulse width (ON time) in
seconds.
Select Alarms All available alarms Applies when Control Mode is set to Alarm. Select
one or more alarms to monitor.
Configuring relay outputs using ION Setup

You can use ION Setup to configure the relay output ports (Relay 1 and Relay 2).
1. Start ION Setup.
4. Select a relay output to configure and click Edit.
The setup screen for that relay output is displayed.
5. Enter a descriptive name for the relay output’s Label.
62 EAV15107-EN09
Relay output setup parameters available through the ION Setup
Label — Use this field to change the default label and assign a
descriptive name to this relay output.
Control Mode External, Alarm This field displays how the relay output functions.
• External: the relay output is controlled remotely
either through software or by a PLC using
commands sent through communications.
• Alarm: the relay output is associated with the
alarm system. The meter sends a pulse to the
relay output port when the alarm is triggered.
Behavior Mode Normal, Timed, Coil Hold

• Normal: this mode applies when control mode is
set to External or Alarm. In the event of trigger
for External mode, the relay output remains in
the closed state until an open command is sent
by the computer or PLC. In the event of trigger
for Alarm mode, the relay output remains in the
closed state until the drop out point is crossed.
• Timed: the relay output remains ON for the
period defined by the On Time setup register.
• Coil Hold: this mode applies when control mode
is set to External or Alarm. For a unary alarm
that is associated with a relay output, you must
set Behavior Mode to Coil Hold. The output
turns on when the “energize” command is
received and turns off when the “coil hold
release” command is received. In the event of a
control power loss, the output remembers and
returns to the state it was in when control power
was lost.
On Time (s) 0 to 9999 This setting defines the pulse width (ON time) in
seconds.
Select Alarms All available alarms Applies when Control Mode is set to Alarm. Select
one or more alarms to monitor.
Associations — This field displays additional information if the relay
output is already associated with another meter
function.
Energy pulsing
You can configure the meter’s alarm /energy LED or the digital output(s) for
energy pulsing.
• The meter is equipped with an alarm / energy pulsing LED. When configured
for energy pulsing, the LED emits pulses that are then used to determine the
accuracy of the meter’s energy measurements.
• The meter sends the pulses from the configured digital output(s) port, which
are then used to determine the accuracy of the meter’s energy
measurements by pulse counter.
Configuring the alarm / energy pulsing LED using the display

You can use the display to configure your meter’s LED for alarming or energy
pulsing applications.
3. Navigate to I/O > LED.
Edit.
EAV15107-EN09 63
5. Press the plus or minus buttons to modify the parameter as required, then
press OK.
Mode Off, Alarm, Energy Off turns off the LED completely.
Alarm sets the LED for alarm

notification.
Energy sets the LED for energy pulsing.
Parameter Active Del Select which accumulated energy

channel to monitor and use for energy
Active Rec pulsing. This setting is ignored when the
Active Del + Rec LED mode is set to Alarm.
Reactive Del
Reactive Rec
Reactive Del + Rec
Apparent Del
Apparent Rec
Apparent Del + Rec
Pulse Wt. (p/k_h) 1 to 9999999 When configured for energy pulsing, this
setting defines how many pulses are
sent to the LED for every 1 kWh, 1
kVARh or 1kVAh accumulated energy.
This setting is ignored when the LED
mode is set to Alarm.
Configuring the alarm / energy pulsing LED or digital output for energy pulsing using
ION Setup
You can use ION Setup to configure your meter’s LED or digital output for energy
pulsing.
1. Start ION Setup.
3. Navigate to I/O configuration > Energy Pulsing.
4. Select the LED or a digital output to configure and click Edit.
The setup screen is displayed.
5. Enter a descriptive name for the digital output’s Label.
64 EAV15107-EN09
Alarm / energy pulsing LED setup parameters available through ION Setup
Mode LED: Disabled, Alarm, LED:

Energy • LED is disabled.
Digital output: External, • Alarm sets the LED for alarm notification.
Energy • Energy sets the LED for energy pulsing.
Digital output:
• Energy: associates the digital output with energy pulsing.
• External: disassociates the digital output from energy pulsing.
Pulse rate (p/k_h) 1 to 9999999 When configured for energy pulsing, this defines how many pulses are sent to
the LED for every 1 kWh, 1 kVARh or 1 kVAh of accumulated energy.
Parameter Active Energy Delivered Select which accumulated energy channel to monitor and use for energy
pulsing.
Active Energy Received
Active Energy Del+Rec
Reactive Energy Delivered
Reactive Energy Received
Reactive Energy Del+Rec
Apparent Energy Delivered
Apparent Energy Received
Apparent Energy Del+Rec
EAV15107-EN09 65
PowerLogic™ PM5300 series Alarms
Alarms
Alarms overview
An alarm is the meter’s means of notifying you when an alarm condition is
detected, such as an error or an event that falls outside of normal operating
conditions. Alarms are typically setpoint-driven and can be programmed to
monitor certain behaviors, events or unwanted conditions in your electrical
system.
You can configure your meter to generate and display high, medium and low
priority alarms when predefined events are detected in the meter’s measured
values or operating states. Your meter also logs the alarm event information.
The meter ships with some alarms already enabled from the factory. Other alarms
need to be configured before the meter can generate alarms.
Customize meter alarms as required, such as changing the priority. You can also
create custom alarms using the advanced features of your meter.
Available alarms
Your meters supports a number of different alarm types.
Type Number
Unary 4
Digital 4
Standard 29
Unary alarms
A unary alarm is the simplest type of alarm — it monitors a single behavior, event
or condition.
Available unary alarms

Your meter has a set of 4 unary alarms.
Alarm label Description
Meter Powerup Meter powers on after losing control power.
Meter Reset Meter resets for any reason.
Meter Diagnostic Meter’s self-diagnostic feature detects a problem.
Phase Reversal Meter detects a phase rotation different than expected.
Digital alarms
Digital alarms monitor the ON or OFF state of the meter’s digital / status inputs.
Digital alarm with setpoint delay

To prevent false triggers from erratic signals, you can set up pickup and dropout
time delays for the digital alarm.
66 EAV15107-EN09
Alarms PowerLogic™ PM5300 series
1
∆T1 ∆T2
0
∆T3
EV1 EV2
A Pickup setpoint (1 = ON) ΔT2 Dropout time delay (in seconds)
B Dropout setpoint (0 = OFF) EV2 End of alarm condition
ΔT1 Pickup time delay (in seconds) ΔT3 Alarm duration (in seconds)
EV1 Start of alarm condition
NOTE: To prevent filling the alarm log with nuisance alarm trips, the digital
alarm is automatically disabled if the digital / status input changes state more
than 4 times in one second or more than 10 times in ten seconds. In this case,
you must re-enable the alarm using the display or ION Setup.
Available digital alarms

Your meter has 2 digital alarms.
Alarm label Description
Digital Alarm S1 Status input 1
Digital Alarm S2 Status input 2
Standard alarms
Standard alarms are setpoint-driven alarms which monitor certain behaviors,
events or unwanted conditions in your electrical system.
Standard alarms have a detection rate equal to the 50/60 meter cycle, which is
nominally 1 second if the meter’s frequency setting is configured to match the
system frequency (50 or 60 Hz).
Many of the standard alarms are three-phase alarms. Alarm setpoints are
evaluated for each of the three phases individually, but the alarm is reported as a
single alarm. The alarm pickup occurs when the first phase exceeds the alarm
pickup magnitude for the pickup time delay. The alarm is active as long as any
phase remains in an alarm state. The alarm dropout occurs when the last phase
drops below the dropout magnitude for the dropout time delay.
Example of over and under setpoint (standard) alarm operation

The meter supports over and under setpoint conditions on standard alarms.
A setpoint condition occurs when the magnitude of the signal being monitored
crosses the limit specified by the pickup setpoint setting and stays within that limit
for a minimum time period specified by the pickup time delay setting.
The setpoint condition ends when the magnitude of the signal being monitored
crosses the limit specified by dropout setpoint setting and stays within that limit for
a minimum time period specified by dropout time delay setting.
Over setpoint
When the value rises above the pickup setpoint setting and remains there long
enough to satisfy the pickup time delay period (ΔT1), the alarm condition is set to
EAV15107-EN09 67
ON. When the value falls below the dropout setpoint setting and remains there
long enough to satisfy the dropout time delay period (ΔT2), the alarm condition is
set to OFF.
A Pickup setpoint
B Dropout setpoint
Max2
Max1 ΔT1 Pickup time delay period (in seconds)

∆T1
∆T2 ΔT2 Dropout time delay (in seconds)
∆T3
EV2 End of alarm condition
ΔT3 Alarm duration (in seconds)
EV1 EV2
Max1 Maximum value recorded during pickup period
Max2 Maximum value recorded during alarm period
The meter records the date and time when the alarm event starts (EV1) and when
it ends (EV2). The meter also performs any task assigned to the event, such as
operating a digital output. The meter also records maximum values (Max1, Max2)
before, during or after the alarm period.
Under setpoint
When the value falls below the pickup setpoint setting and remains there long
enough to satisfy the pickup time delay period (ΔT1), the alarm condition is set to
ON. When the value rises above the dropout setpoint setting and remains there
long enough to satisfy the dropout time delay period (ΔT2), the alarm condition is
set to OFF.
A Pickup setpoint
∆T3 B Dropout setpoint
ΔT1 Pickup time delay period (in seconds)

∆T2
∆T1
ΔT2 Dropout time delay (in seconds)
Min1 EV2 End of alarm condition
Min2
ΔT3 Alarm duration (in seconds)
EV1 EV2
Min1 Minimum value recorded during pickup period
Min2 Minimum value recorded during alarm period
The meter records the date and time when the alarm event starts (EV1) and when
it ends (EV2). The meter also performs any task assigned to the event, such as
operating a digital output. The meter also records minimum values (Min1, Min2)
before, during or after the alarm period.
Maximum allowable setpoint

The meter is programmed to help prevent user data entry errors, with set limits for
the standard alarms.
The maximum setpoint value you can enter for some of the standard alarms
depends on the voltage transformer ratio (VT ratio), current transformer ratio (CT
ratio), system type (i.e., number of phases) and/or the maximum voltage and
maximum current limits programmed at the factory.
NOTE: VT ratio is the VT primary divided by the VT secondary and CT ratio is
the CT primary divided by the CT secondary.
68 EAV15107-EN09
Standard alarm Maximum setpoint value
Over Phase Current (maximum current) x (CT ratio)
Under Phase Current (maximum current) x (CT ratio)
Over Neutral Current (maximum current) x (CT ratio) x (number of phases)
Over Ground Current (maximum current) x (CT ratio)
Over Voltage L-L (maximum voltage) x (VT ratio)
Under Voltage L-L (maximum voltage) x (VT ratio)
Over Voltage L-N (maximum voltage) x (VT ratio)
Under Voltage L-N (maximum voltage) x (VT ratio)
Over Active Power (maximum voltage) x (maximum current) x (number of phases)
Over Reactive Power (maximum voltage) x (maximum current) x (number of phases)
Over Apparent Power (maximum voltage) x (maximum current) x (number of phases)
Over Present Active Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Last Active Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Predicted Active Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Present Reactive Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Last Reactive Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Predicted Reactive Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Present Apparent Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Last Apparent Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Predicted Apparent Power Demand (maximum voltage) x (maximum current) x (number of phases)
Over Voltage Unbalance (maximum voltage) x (VT ratio)
Phase Loss (maximum voltage) x (VT ratio)
Available standard alarms

Your meter has a set of standard alarms.
NOTE: Some alarms do not apply to all power system configurations. For
example, line-to-neutral voltage alarms cannot be enabled on 3-phase delta
systems. Some alarms use the system type and the VT or CT ratio to
determine the maximum allowed setpoint.
Alarm label Valid range and resolution

Units
ION Setup Display ION Setup Display
Over Phase Current Over Current, Ph 0.000 to 99999.000 0 to 99999 A
Under Phase Current Under Current, Ph 0.000 to 99999.000 0 to 99999 A
Over Neutral Current Over Current, N 0.000 to 99999.000 0 to 99999 A
Over Ground Current Over Current, Gnd 0.000 to 99999.000 0 to 99999 A
Over Voltage L-L Over Voltage, L-L 0.00 to 999999.00 0 to 999999 V
Under Voltage L-L Under Voltage, L-L 0.00 to 999999.00 0 to 999999 V
Over Voltage L-N Over Voltage, L-N 0.00 to 999999.00 0 to 999999 V
Under Voltage L-N Under Voltage L-N 0.00 to 999999.00 0 to 999999 V
Over Active Power Over kW 0.0 to 9999999.0 0 to 9999999 kW

Over Reactive Power Over kVAR 0.0 to 9999999.0 0 to 9999999 kVAR
Over Apparent Power Over kVA 0.0 to 9999999.0 0 to 9999999 kVA
EAV15107-EN09 69
Alarm label Valid range and resolution

Units
ION Setup Display ION Setup Display
Leading True PF Lead PF, True -1.00 to -0.01 and 0.01 to 1.00 —
Lagging True PF Lag PF, True -1.00 to -0.01 and 0.01 to 1.00 —
Leading Disp PF Lead PF, Disp -1.00 to -0.01 and 0.01 to 1.00 —
Lagging Disp PF Lag PF, Disp -1.00 to -0.01 and 0.01 to 1.00 —
Over Present Active Power Demand Over kW Dmd, Pres 0.0 to 9999999.0 0 to 9999999 kW
Over Last Active Power Demand Over kW Dmd, Last 0.0 to 9999999.0 0 to 9999999 kW
Over Predicted Active Power Demand Over kW Dmd, Pred 0.0 to 9999999.0 0 to 9999999 kW
Over Present Reactive Power Demand Over kVAR Dmd, Pres 0.0 to 9999999.0 0 to 9999999 kVAR
Over Last Reactive Power Demand Over kVAR Dmd, Last 0.0 to 9999999.0 0 to 9999999 kVAR
Over Predicted Reactive Power Demand Over kVAR Dmd, Pred 0.0 to 9999999.0 0 to 9999999 kVAR
Over Present Apparent Power Demand Over kVA Dmd, Pres 0.0 to 9999999.0 0 to 9999999 kVA
Over Last Apparent Power Demand Over kVA Dmd, Last 0.0 to 9999999.0 0 to 9999999 kVA
Over Predicted Apparent Power Demand Over kVA Dmd, Pred 0.0 to 9999999.0 0 to 9999999 kVA
Over Frequency Over Frequency 0.000 to 99.000 Hz
Under Frequency Under Frequency 0.000 to 99.000 Hz
Over Voltage Unbalance Over Voltage Unbal 0 to 99 %
Over Voltage THD Over Voltage THD 0 to 99 %
Phase Loss Phase Loss 0.00 too 999999.00 0 to 999999 —
Power factor (PF) alarms

You can set up a Leading PF or Lagging PF alarm to monitor when the circuit’s
power factor goes above or below the threshold you specify.
The Leading PF and Lagging PF alarms use the power factor quadrants as the
values on the y-axis, with quadrant II on the lowest end of the scale, followed by
quadrant III, quadrant I, and finally quadrant IV on the highest end of the scale.
Quadrant PF values Lead/Lag
II 0 to -1 Leading (capacitive)
III -1 to 0 Lagging (inductive)
I 0 to 1 Lagging (inductive)
IV 1 to 0 Leading (capacitive)
Leading PF alarm
The Leading PF alarm monitors an over setpoint condition.
0
IV
-1
I ∆T1
0
III
+1
∆T2
∆T3
II
0
EV1 EV2
A Pickup setpoint ΔT2 Dropout time delay (in seconds)
70 EAV15107-EN09
B Dropout setpoint EV2 End of alarm condition
ΔT1 Pickup delay period (in seconds) ΔT3 Alarm duration (in seconds)
Lagging PF alarm
The Lagging PF alarm monitors an under setpoint condition.
0
IV ∆T3
-1
I ∆T2
0
III
+1 ∆T1
II
0
EV1 EV2
A Pickup setpoint ΔT2 Dropout time delay (in seconds)
B Dropout setpoint EV2 End of alarm condition
ΔT1 Pickup delay period (in seconds) ΔT3 Alarm duration (in seconds)
Phase loss alarm

The phase loss alarm is an under setpoint alarm that monitors the voltages on a 3-
phase system and triggers the alarm when one or two phases fall below the
pickup setpoint setting and remain there long enough to satisfy the pickup time
delay period.
When all of the phases rise above the dropout setpoint setting and remain there
long enough to satisfy the dropout time delay period, the alarm condition is set to
OFF.
Alarm priorities
Each alarm has a priority level that you can use to distinguish between events that
require immediate action and those that do not require action.
Alarm priority Alarm display notification and recording method
Alarm LED Alarm icon Alarm details Alarm logging
High Blinks while the alarm is Blinks while the alarm is Click Details to display Recorded in alarm log.
active. active. Alarm icon remains what caused the alarm to
displayed until pickup or drop off. Click
acknowledged. Ack to acknowledge the
alarm.
Medium Blinks while the alarm is Blinks while the alarm is Click Details to display Recorded in alarm log.
active. active. what caused the alarm to
pickup or drop off.
Low Blinks while the alarm is Blinks while the alarm is Click Details to display Recorded in alarm log.
active. active. what caused the alarm to
pickup or drop off.
None No activity None None Recorded in event log only.
NOTE: The alarm LED notification only occurs if the alarm / energy pulsing
LED is configured for alarming.
EAV15107-EN09 71
Multiple alarm considerations

If multiple alarms with different priorities are active at the same time, the display
shows the alarms in the order they occurred.
Alarm setup overview

You can use the meter display or ION Setup to configure unary, digital or standard
(1-Sec) alarms.
If you make changes to the basic power meter setup, all alarms are disabled to
prevent undesired alarm operation. If you configure standard alarm setpoints
using the display, any decimals previously configured using ION Setup are lost.
NOTICE
UNINTENDED EQUIPMENT OPERATION
• Verify all alarm settings are correct and make adjustments as necessary.
• Re-enable all configured alarms.
Failure to follow these instructions can result in incorrect alarm functions.
Built-in error-checking
ION Setup dynamically checks incorrect setup combinations. When you enable an
alarm, you must set up the pickup and dropout limits to acceptable values first in
order to exit the setup screen.
Setting up alarms using the display

You can use the display to create and set up standard (1-Sec), unary and digital
alarms.
It is recommended that you use ION Setup to configure standard (1-Sec) alarms.
ION Setup supports a higher resolution to allow you to specify more decimal
places when setting up the pickup setpoint and dropout setpoint values for certain
measurements.
1. Navigate to the alarms setup menu screens and select the alarm you want to
set up.
2. Configure the setup parameters as explained in the different alarm setup
sections.
NOTE: If you used ION Setup to program decimal values on a standard
(1-Sec) alarm, do not use the meter display to make subsequent changes
to any alarm parameters (including enable/disable), as doing so will
cause removal of all decimals previously programmed through ION
Setup.
3. Click Yes to save the changes to the meter when prompted.
Setting up alarms using ION Setup

You can use ION Setup to create and set up alarms.
1. Start ION Setup and connect to your meter.
2. Open the Alarming screen.
3. Select the alarm you want to configure and click Edit.
72 EAV15107-EN09
4. Configure the setup parameters as explained in the different alarm setup

sections.
See the ION Setup Device Configuration guide for more information.
Unary alarm setup parameters

Configure the unary alarm setup parameters as required.
ION Setup controls are shown in parentheses.
Enable Yes (checked) or No (cleared) This enables or disables the alarm.
Priority High, Medium, Low, None This sets the alarm priority and notification
options.
Select Dig Output (Outputs) None Select the output(s) you want to control
when the alarm is triggered.
Select Relay (Outputs) Digital Output D1
Digital Output D2
Digital Output D1+D2
Relay R1
Relay R2
Relay R1+R2
Digital alarm setup parameters

Configure the digital alarm setup parameters as required.
options.
Pickup Setpoint (Setpoint Pickup) On, Off Use this setting to control when to trip the
alarm, based on the state of the digital input
(On or Off).
Pickup Time Delay (Setpoint Pickup Delay) 0 to 999999 This specifies the number of seconds the
digital input must be in the alarm pickup
state before the alarm is tripped.
Dropout Time Delay (Setpoint Dropout 0 to 999999 This specifies the number of seconds the
Delay) digital input must be out of the alarm pickup
state before the alarm turns off.
Digital Output D2
Relay R1
Relay R2
Relay R1+R2
Standard (1-Sec) alarm setup parameters

Configure the standard alarm setup parameters as required.
EAV15107-EN09 73
NOTE: It is recommended that you use ION Setup to configure standard (1-
Sec) alarms. ION Setup supports a higher resolution to allow you to specify
more decimal places when setting up the pickup setpoint and dropout setpoint
values for certain measurements.
options.
Pickup Setpoint (Pickup Limit) Varies depending on the standard alarm you This is the value (magnitude) you define as
are setting up the setpoint limit for triggering the alarm. For
“over” conditions, this means the value has
gone above the Pickup limit. For “under”
conditions, this means the value has gone
below the Pickup limit.
Pickup Time Delay (Delay) 0 to 999999 This specifies the number of seconds the
signal must stay above the pickup setpoint
(for “over” conditions), or below the pickup
setpoint (for “under” conditions) before the
alarm is tripped.
Dropout Setpoint (Dropout Limit) Varies depending on the standard alarm you This is the value (magnitude) you define as
are setting up the limit for dropping out of the alarm
condition. For “over” conditions, this means
the value has gone below the Dropout limit.
For “under” conditions, this means the value
has gone above the Pickup limit.
Dropout Time Delay (Delay) 0 to 999999 This specifies the number of seconds the
signal must stay below the dropout setpoint
(for “over” conditions), or above the dropout
setpoint (for “under” conditions) before the
alarm condition is ended.
PU Set Point Lead/Lag (Lead, Lag) Lead or Lag Applies to PF (power factor) alarms only.
Use this to set the PF value and quadrant to
set the pickup setpoint for an over PF
condition (PF Leading) or under PF
condition (PF Lagging).
DO Set Point Lead/Lag (Lead, Lag) Lead or Lag Applies to PF (power factor) alarms only.
Use this to set the PF value and quadrant to
set the dropout setpoint for an over PF
condition (PF Leading) or under PF
condition (PF Lagging).
Digital Output D2
Relay R1
Relay R2
Relay R1+R2
LED alarm indicator

You can use the meter’s alarm / energy pulsing LED as an alarm indicator.
When set to detect alarms, the LED blinks to indicate an alarm condition.
Configuring the LED for alarms using the display

You can use the meter display to configure the alarm / energy pulsing LED for
alarming.
1. Navigate to the LED setup menu screen.
74 EAV15107-EN09
2. Set the mode to Alarm, then press OK.

Configuring the LED for alarms using ION Setup

You can use the ION Setup to configure your meter’s LED for alarming.
1. Open ION Setup and connect to your meter. See the ION Setup Help for
instructions.
2. Navigate to I/O configuration > Energy Pulsing.
3. Select Front Panel LED and click Edit.
4. Set the control mode to Alarm.
Alarm display and notification

The meter notifies you when an alarm condition is detected.
Alarm icon
When a low, medium or high priority alarm is tripped, this symbol appears at the
top right corner of the display screen, indicating that an alarm is active:
For high priority alarms, the alarm icon remains displayed until you acknowledge
the alarm.

If configured for alarming, the alarm / energy pulsing LED also flashes to indicate
the meter has detected an alarm condition.
Alarm screens
You can use the display buttons to navigate to the alarm setup or display screens.
Active alarms
When a pickup event occurs, the active alarm list appears on the meter display’s
Active Alarms screen. Press Detail to see more event information.
Alarm details
Details about the alarms can be viewed using:
• the active alarms (Active), alarm history (Hist), alarm counters (Count) and
unacknowledged alarms (Unack) screens on the meter display, or
Active alarms list and alarm history log

Each occurrence of a low, medium or high priority alarm is stored in the active
alarms list and recorded in the alarm history log.
EAV15107-EN09 75
The active alarm list holds 40 entries at a time. The list works as a circular buffer,
replacing old entries as new entries over 40 are entered into the active alarms list.
The information in the active alarms list is volatile and reinitializes when the meter
resets.
The alarm history log holds 40 entries. The log also works as a circular buffer,
replacing old entries with new entries. The information in the alarm history log is
nonvolatile and is retained when the meter resets.
Viewing active alarm details using the display

When an alarm condition becomes true (alarm = ON), the alarm is displayed on
the active alarms screen.
Alarms are displayed sequentially in the order of their occurrence, regardless of
priority. The alarm details show the date and time of the alarm event, the type of
event (for example, pickup or unary), which phase the alarm condition was
detected on, and the value that caused the alarm condition.
NOTE: Alarm details are not available if the alarm priority is set to None.
The alarm details (for low, medium and high priority alarms) are also recorded in
the alarm history log.
1. Navigate to Alarm > Active.
2. Select the alarm you want to view (the latest ones appear on top).
3. Press Detail.
NOTE: For unacknowledged high priority alarms, the Ack option appears
on this screen. Press Ack to acknowledge the alarm, or return to the
previous screen if you do not want to acknowledge the alarm.
Viewing alarm history details using the display

The alarm history log keeps a record of active alarms and past alarms.
When an active alarm condition becomes false (alarm = OFF), the event is
recorded in the alarm history log and alarm notification (alarm icon, alarm LED) is
turned off.
Alarms are displayed sequentially in the order of their occurrence, regardless of
priority. The alarm details show the date and time of the alarm event, the type of
event (for example, dropout or unary), which phase the alarm condition was
detected on, and the value that caused the alarm condition to turn ON or OFF.
NOTE: Alarm details are not available if the alarm priority is set to None.
1. Navigate to Alarm > Hist.
2. Select the alarm you want to view (the latest ones appear on top).
3. Press Detail.
NOTE: For unacknowledged high priority alarms, the Ack option appears
on this screen. Press Ack to acknowledge the alarm, or return to the
previous screen if you do not want to acknowledge the alarm.
Viewing alarms counters using the display

Every occurrence of each type of alarm is counted and recorded in the meter.
NOTE: The alarm counters roll over to zero after reaching the value 9999.
1. Select Alarm > Count.
The Alarms Counter screen displays.
2. Scroll through the list to view the number of alarm occurrences for each type
of alarm.
76 EAV15107-EN09
Acknowledging high-priority alarms using the display

You can use the meter display to acknowledge high-priority alarms.
1. Navigate to Alarm > Unack.
2. Select the alarm you want to acknowledge.
3. Press Detail.
4. Press Ack to acknowledge the alarm.
5. Repeat for other unacknowledged alarms.
Resetting alarms using ION Setup

Use ION Setup to reset alarms.
You can also reset alarms using the meter display.
1. Connect to your meter in ION Setup.
2. Open the Meter Resets screen.
3. Select the alarm parameters to clear and click Reset.
EAV15107-EN09 77
PowerLogic™ PM5300 series Measurements
Measurements
Real-time readings
The power and energy meter measures current and voltages and reports in real
time the RMS (Root Mean Squared) values for all three phases and neutral.
The voltage and current inputs are continuously monitored at a sampling rate of
64 points per cycle. This amount of resolution helps enable the meter to provide
reliable measurements and calculated electrical values for various commercial,
buildings and industrial applications.
Energy
The meter provides fully bi-directional, 4-quadrant energy metering.
The meter calculates and stores all accumulated active, reactive and apparent
energy measurements in nonvolatile memory:
• Wh, VARh, VAh (delivered and received)
• Wh, VARh, VAh net (delivered - received)
• Wh, VARh, VAh absolute (delivered + received)
All energy parameters represent the total for all three phases. You can view
accumulated energy from the display.
Configuring the energy scaling using ION Setup

You can use ION Setup to configure the energy scaling. Based on the scaling, the
energy overflow happens upon reaching the threshold value.
1. Start ION Setup.
3. Open the Energy Scaling screen.
4. Click Edit to configure the Setup parameters as required.
5. Use the drop-down list to select the parameter you want to set for your
Energy Scaling.
NOTE: If you set Energy Scaling parameter, for which the threshold
value is less than the accumulated energy, the accumulated energy
resets to zero.
78 EAV15107-EN09
Measurements PowerLogic™ PM5300 series
6. Click Send to save your changes to the meter.
Energy Scaling parameters available using the ION Setup
Auto 0 to 9.2233 E The energy value units automatically change, based on the quantity of energy
accumulated, from Kilo to Mega, Mega to Giga, Giga to Tera, Tera to Peta and Peta to Exa.
(Default)
When any one of the energy parameter (delivered or received) exceeds 9.2233 E, all the
energy parameters reset to 0.
Kilo (k) 0 to 999.99 k When any one of the energy parameter (delivered or received) exceeds 999.99 k, all the
Mega (M) 0 to 999.99 M The energy value units automatically change, based on the quantity of energy
accumulated, from Kilo to Mega.
When any one of the energy parameter (delivered or received) exceeds 999.99 M, all the
Giga (G) 0 to 999.99 G The energy value units automatically change, based on the quantity of energy
accumulated, from Kilo to Mega and Mega to Giga.
When any one of the energy parameter (delivered or received) exceeds 999.99 G, all the
Tera (T) 0 to 999.99 T The energy value units automatically change, based on the quantity of energy
accumulated, from Kilo to Mega, Mega to Giga and Giga to Tera.
When any one of the energy parameter (delivered or received) exceeds 999.99 T, all the
Peta (P) 0 to 999.99 P The energy value units automatically change, based on the quantity of energy
accumulated, from Kilo to Mega, Mega to Giga, Giga to Tera and Tera to Peta.
When any one of the energy parameter (delivered or received) exceeds 999.99 P, all the
Exa (E) 0 to 9.2233 E The energy value units automatically change, based on the quantity of energy
accumulated, from Kilo to Mega, Mega to Giga, Giga to Tera, Tera to Peta and Peta to Exa.
When any one of the energy parameter (delivered or received) exceeds 9.2233 E, all the
Preset energy
NOTE: Not applicable for MID meter models.
You can input the previous energy values when you replace the meter. Preset
energy value cannot be set more than maximum energy overflow value (9.2233
E).
The preset energy values include active energy (Wh), reactive energy (VARh),
apparent energy (VAh) (delivered and received).
Configuring the preset energy using ION Setup

NOTE: Not applicable for MID meter models.
You can use ION Setup to configure the preset energy values.
1. Start ION Setup.
3. Open the Preset Energy screen.
4. Click Edit to configure the Setup parameters as required.
5. From the list, set the Preset Energy value for each parameter.
EAV15107-EN09 79
6. Click Send to save your changes to the meter.
Preset Energy parameters available using the ION Setup
Active Energy Delivered 0 to 9.2233 E Use this field to enter the preset energy values
Active Energy Received
Reactive Energy Delivered
Reactive Energy Received
Apparent Energy Delivered
Apparent Energy Received
Min/max values
When the readings reach their lowest or highest value, the meter updates and
saves these min/max (minimum and maximum) quantities in non-volatile memory.
The meter’s real-time readings are updated once every 50 cycles for 50 Hz
systems, or once every 60 cycles for 60 Hz systems.
Demand
Power demand
Power demand is a measure of average power consumption over a fixed time
interval.
NOTE: If not specified, references to demand are assumed to mean power
demand.
The meter measures instantaneous consumption and can calculate demand using
various methods.
Current demand
The meter calculates current demand using the block interval, synchronized or
thermal demand methods.
You can set the demand interval from 1 to 60 minutes in 1 minute increments (for
example, 15 minutes).
Power demand calculation methods

Power demand is calculated by dividing the energy accumulated during a
specified period by the length of that period.
How the meter performs this calculation depends on the method and time
parameters you select (for example, timed rolling block demand with a 15-minute
interval and 5-minute subinterval).
To be compatible with electric utility billing practices, the meter provides the
following types of power demand calculations:
• Block interval demand
• Synchronized demand
• Thermal demand
You can configure the power demand calculation method from the display or
software.
80 EAV15107-EN09
Block interval demand

For block interval demand method types, you specify a period of time interval (or
block) that the meter uses for the demand calculation.
Select/configure how the meter handles that interval from one of these different
methods:
Type Description
Timed Sliding Block Select an interval from 1 to 60 minutes (in 1-minute increments). If
the interval is between 1 and 15 minutes, the demand calculation
updates every 15 seconds. If the interval is between 16 and 60
minutes, the demand calculation updates every 60 seconds. The
meter displays the demand value for the last completed interval.
Timed Block Select an interval from 1 to 60 minutes (in 1-minute increments). The
meter calculates and updates the demand at the end of each
interval.
Timed Rolling Block Select an interval and a subinterval. The subinterval must divide
evenly into the interval (for example, three 5-minute subintervals for
a 15-minute interval). Demand is updated at the end of each
subinterval. The meter displays the demand value for the last
completed interval.
Block interval demand example

The following illustration shows the different ways power demand is calculated
using the block interval method. In this example, the interval is set to 15 minutes.
Timed Sliding Block
Demand value is
Calculation updates the average for the
every 15 seconds last completed interval
15-minute interval
Time (sec)
15 30 45 60 . . .
Timed Block
Demand value is
the average for the
Calculation updates at
last completed
the end of the interval
interval
15-minute interval 15-minute interval 15-min
Time
(min)
15 30 45
Timed Rolling Block
Calculation updates at the end Demand value is

of the subinterval (5 minutes) the average for
the last completed
interval
15-minute interval
Time
(min)
15 20 25 30 35 40 45
EAV15107-EN09 81
Synchronized demand
You can configure the demand calculations to be synchronized using an external
pulse input, a command sent over communications, or the device’s internal real-
time clock.
Type Description
Input synchronized This method allows you to synchronize the demand interval of your meter
demand with an external digital pulse source (such as another meter’s digital
output) connected to your meter's digital input. This helps synchronize
your meter to the same time interval as the other meter for each demand
calculation.
Command This method allows you to synchronize the demand intervals of multiple
synchronized demand meters on a communications network. For example, if a programmable
logic controller (PLC) input is monitoring a pulse at the end of a demand
interval on a utility revenue meter, you can program the PLC to issue a
command to multiple meters whenever the utility meter starts a new
demand interval. Each time the command is issued, the demand readings
of each meter are calculated for the same interval.
Clock synchronized This method allows you to synchronize the demand interval to the meter’s
demand internal real-time clock. This helps you synchronize the demand to a
particular time, typically on the hour (for example, at 12:00 am). If you
select another time of day when the demand intervals are to be
synchronized, the time must be specified in minutes from midnight. For
example, to synchronize at 8:00 am, select 480 minutes.
NOTE: For these demand types, you can choose block or rolling block
options. If you select a rolling block demand option, you need to specify a
subinterval.
Thermal demand
Thermal demand calculates the demand based on a thermal response, which
imitates the function of thermal demand meters.
The demand calculation updates at the end of each interval. You can set the
demand interval from 1 to 60 minutes (in 1-minute increments).
Thermal demand example

The following illustration shows the thermal demand calculation. In this example,
the interval is set to 15 minutes. The interval is a window of time that moves
across the timeline. The calculation updates at the end of each interval.
99%
90% Last completed
demand interval
% of Load
Time
(minutes)
15-minute next
interval 15-minute
interval
Peak demand
The meter records the peak (or maximum) values for kWD, kVARD, and kVAD
power (or peak demand).
The peak for each value is the highest average reading since the meter was last
reset. These values are maintained in the meter’s non-volatile memory.
The meter also stores the date and time when the peak demand occurred. In
addition to the peak demand, the meter also stores the coinciding average 3-
82 EAV15107-EN09
phase power factor. The average 3-phase power factor is defined as “demand kW/
demand kVA” for the peak demand interval.
Predicted demand
The meter calculates predicted demand for the end of the present interval for kW,
kVAR, and kVA demand, taking into account the energy consumption so far within
the present (partial) interval and the present rate of consumption.
Predicated demand is updated according to the update rate of your meter.
The following illustration shows how a change in load can affect predicted demand
for the interval. In this example, the interval is set to 15 minutes.
1:00 1:06 1:15
A Beginning of interval E Change in load
B Demand for last completed interval F Predicted demand if load is added

during interval; predicted demand
increases to reflect increased demand
C 15-minute interval G Predicted demand if no load is added
D Partial interval H Time
Setting up demand calculations

Use the Demand setup screens to define power or current demand.
Demand is a measure of average consumption over a fixed time interval.
3. Navigate to Meter > Dmd.
4. Move the cursor to select Power Demand or Current Demand.
Edit.
Values Description
Method
Timed Sliding Block Select the appropriate demand calculation
method for your needs
Timed Block
Timed Rolling Block
Cmd Sync Block
Cmd Sync Roll Block
Clock Sync Block
Clock Sync Roll Block
Input Sync Block
EAV15107-EN09 83
Values Description
Input Sync Roll Block
Thermal
Interval
0 - 60 Set the demand interval, in minutes.
Subinterval
0 - 60 Applies only to rolling block methods.
Define how many subintervals the demand

interval should be equally divided into.
Select Dig Output
None Select which digital output the end of demand

interval pulse should be sent to.
Digital Output D1
Digital Output D2
Select Dig Input
None Applies only to input sync methods.
Digital Input S1 Select which digital input is used to sync the

demand.
Digital Input S2
Clock Sync Time
0 - 2359 Applies only to clock sync methods (these

synchronize the demand interval to the
meter’s internal clock).
Define what time of day you want to

synchronize the demand, from the start of the
day. For example, set this setting to 0730 to
synchronize demand at 7:30 AM.

Power factor (PF)

Power factor (PF) is the ratio of real power (P) to apparent power (S).
PF is provided as a number between -1 and 1 or as a percentage from -100% to
100%, where the sign is determined by the convention.
P
PF = —
S
A purely resistive load has no reactive components, so its power factor is 1 (PF =
1, or unity power factor). Inductive or capacitive loads introduce a reactive power
(Q) component to the circuit which causes the PF to become closer to zero.
True PF and displacement PF

The meter supports true power factor and displacement power factor values:
• True power factor includes harmonic content.
• Displacement power factor only considers the fundamental frequency.
NOTE: Unless specified, the power factor displayed by the meter is true power
factor.
84 EAV15107-EN09
Real, reactive and apparent power (PQS)

A typical AC electrical system load has both resistive and reactive (inductive or
capacitive) components.
Real power, also known as active power (P) is consumed by resistive loads.
Reactive power (Q) is either consumed by inductive loads or generated by
capacitive loads.
Apparent power (S) is the capacity of your measured power system to provide real
and reactive power.
The units for power are watts (W or kW) for real power P, vars (VAR or kVAR) for
reactive power Q, and volt-amps (VA or kVA) for apparent power S.
+Q
(+kVAR, +kVARh)
Quadrant 2 90° Quadrant 1

PF leading PF lagging
Power factor sign convention: Power factor sign convention:
IEEE = + IEEE = −
IEC = − IEC = +
Reactive power (VAR)

Imported/delivered
Imported/delivered
A)
Ap
(V
par
er
en
w
tp
po
ow
nt
re
er
pa
(V
Ap
Active power (W) A) Active power (W)
Exported/received Imported/delivered
-P +P
(-kW, -kWh) 180° 0° (+kW, +kWh)
Active power (W) Active power (W)

Exported/received Imported/delivered
Exported/received
Exported/received
A)
Ap
(V
p
ar
er
en
w
po
tp
ow
nt
re
er
pa
(V
Ap
A)
Quadrant 3 Quadrant 4
PF lagging PF leading
Power factor sign convention: Power factor sign convention:
IEEE = − IEEE = +
IEC = − IEC = +
270°
-Q
(-kVAR, -kVARh)
Power flow
Positive real power P(+) flows from the power source to the load. Negative real
power P(-) flows from the load to the power source.
Power factor sign convention

Power factor sign (PF sign) can be positive or negative, and is defined by the
conventions used by the IEEE or IEC standards.
You can set the power factor sign (PF sign) convention that is used on the display
to either IEC or IEEE.
PF sign convention: IEC

PF sign correlates with the direction of real power (kW) flow.
• Quadrant 1 and 4: Positive real power (+kW), the PF sign is positive (+).
• Quadrant 2 and 3: Negative real power (-kW), the PF sign is negative (-).
PF sign convention: IEEE

PF sign is correlates with the PF lead/lag convention, in other words, the effective
load type (inductive or capacitive):
EAV15107-EN09 85
• For a capacitive load (PF leading, quadrant 2 and 4), the PF sign is positive
(+).
• For an inductive load (PF lagging, quadrant 1 and 3), the PF sign is negative
(-).
Power factor register format

The meter provides power factor values in a variety of formats to suit your energy
management software.
Power factor in IEC and lead/lag (IEEE) formats: Float32 and

Int16U registers
The meter provides total power factor in IEC and lead/lag (IEEE) formats in both
Float32 and Int16U data types. You can use these registers to bring power factor
information into third-party software. These registers are interpreted using the
standard IEC and IEEE sign conventions.
NOTE: For information on how to calculate actual power factor values from
the values in Int16U registers, see your meter’s Modbus register list, available
from www.se.com.
Four quadrant power factor information: floating point registers

The meter also provides PF information (including sign and quadrant) in single
floating point registers for each of the PF values (for example, per-phase and total
values for true and displacement PF, and associated minimums and maximums).
The meter performs a simple algorithm to the PF value then stores it in the
appropriate PF register.
The meter and software (such as Power Monitoring Expert or ION Setup) interpret
these PF registers for reporting or data entry fields according to the following
diagram:
86 EAV15107-EN09
-0.5 +0.5
-1 ≤ PF ≤ 0 0 ≤ PF ≤ 1
-1 +1
-1 ≤ PF ≤ 0 0 ≤ PF ≤ 1
-0.5 +0.5
PF value 0 to -1 -1 to 0 0 to +1 +1 to 0
0 -1 0 +1 0
Quadrant 3 Quadrant 2 Quadrant 1 Quadrant 4
-2 -1 0 +1 +2
PF register -2 to -1 -1 to 0 0 to +1 +1 to +2
0 0
-0.5 +0.5
-1 ≤ PF register ≤ 0 0 ≤ PF register ≤ 1
-1 +1
-2 ≤ PF register ≤ -1 2 ≤ PF register ≤ 1
-1.5 +1.5
-2 +2
The PF value is calculated from the PF register value using the following formulas:
Quadrant PF range PF register range PF formula
Quadrant 1 0 to +1 0 to +1 PF value = PF register

value
Quadrant 2 -1 to 0 -1 to 0 PF value = PF register
value
EAV15107-EN09 87
Quadrant PF range PF register range PF formula
Quadrant 3 0 to -1 -2 to -1 PF value = (-2) - (PF

register value)
Quadrant 4 +1 to 0 +1 to +2 PF value = (+2) - (PF

register value)
Go to www.se.com and search for your meter’s Modbus register list to download a
copy.
Timers
The meter supports an I/O timer, active load timer and an operating timer.
Use the meter display to navigate to the Timer and I/O screens to view timer
information.
Operating Timer
The operating timer (Timer > Oper) keeps track of how long the meter has been
powered up.
Load Timer
The load timer keeps track of how much time the input current exceeds the
specified load timer setpoint current.
I/O timer
The I/O timer shows how long an input or output has been ON.
88 EAV15107-EN09
Resets PowerLogic™ PM5300 series
Resets
Meter resets
Resets allow you to clear various accumulated parameters stored on your meter
or reinitialize the meter or meter accessories.
Meter resets clear your meter’s onboard data logs and other related information.
Resets are typically performed after you make changes to the meter’s basic setup
parameters (such as frequency, VT/PT or CT settings) to clear invalid or obsolete
data in preparation for putting the meter into active service.
Meter Initialization
Meter Initialization is a special command that clears the meter’s logged data,
counters and timers.
It is common practice to initialize the meter after its configuration is completed,
before adding it to an energy management system.
After configuring all the meter setup parameters, navigate through the different
meter display screens and make sure the displayed data is valid then perform
meter initialization.
Performing global resets using the display

Global resets allow you to clear all data of a particular type, such as all energy
values or all minimum/maximum values.
1. Navigate to Maint > Reset.
2. Move the cursor to point to Global Reset, then press Select.
3. Move the cursor to point to the parameter you want to reset, then press
Reset.
Option Description
Meter Initialization Clears all data listed in this table (energy, demand, min/max
values, counters, logs and timers).
Energies Clears all accumulated energy values (kWh, kVARh, kVAh).
Demands Clears all the demand registers.
Min/Max Clears all the minimum and maximum registers.
Alarm Counts & Logs Clears all the alarm counters and alarm logs.
I/O Counts & Timers Clears all the I/O counters and resets all the timers.
4. Enter the reset password (default is “0”), then press OK.

5. Press Yes to confirm the reset or No to cancel and return to the previous
screen.
To perform resets using ION Setup, see the “PM5300” topic in the ION Setup
online help or in the ION Setup device configuration guide, available from
www.se.com.
Performing single resets using the display

Single resets allow you clear data only in a specific register or register type.
EAV15107-EN09 89
PowerLogic™ PM5300 series Resets
Single resets are often combined to allow you to clear all data of a similar type, for
example, a kWh, kVAR and kVA reset may be combined into an energy reset that
clears all of the meter’s energy logs.
1. Navigate to Maint > Reset.
2. Move the cursor to point to Single Reset, then press Select.
3. Move the cursor to point to the parameter you want to reset, then press
Reset.
If there are additional options for the parameter, press Select, move the
cursor to point to the option you want, then press Reset.
4. Enter the reset password (default is “0”), then press OK.
5. Press Yes to confirm the reset or No to cancel and return to the previous
screen.
Available single resets using the display
Parameter Option Description
Energy Accumulated Clears all accumulated energy values (kWh, kVARh, kVAh).
Demand Power, Current Select which demand registers to clear (power demand or current
demand).
Alarms Event Queue Clears the alarm event queue register (active alarms list).
History Log Clears the alarm history log.
Counters Select Counters and then select which alarm counter to clear. See the
Alarm counter reset options table.
Status Inputs Timers Select Timers then select which status input timer to clear (chose all or
individual status input timers)
Counters Select Counters then select which status input counter to clear (chose all
or individual status input timers)
Digital Outputs Timers Select Timers then select which digital output timer to clear (chose all or
individual digital output timers)
Counters Select Counters then select which digital output counter to clear (chose all
or individual digital output timers)
Active Load Timer — Clears and restarts the load operation timer.
Multi-Tariff — Clears accumulated values in all tariff registers.
To perform resets using ION Setup, see the “PM5300” topic in the ION Setup
online help or in the ION Setup device configuration guide, available from
www.se.com.
90 EAV15107-EN09
Multi-tariffs PowerLogic™ PM5300 series
Multi-tariffs
Multi-tariff
The multi-tariff feature allows you to set up different tariffs for storing energy
values.
The energy values for different tariffs are stored in registers that correspond to
each of those tariffs.
Multi-tariff example
The multi-tariff feature can be used when a utility has set up tariff schedules with
different rates based on what day or time of day energy is consumed.
Power
Time
Cost
Tariff energy containers
T1 T2 T3 T4
T1 T2 T3 T4
In the above illustration, the area under the power curve equals the energy
consumed.
Typically, the utility sets tariff schedules so the cost of energy is higher during high
demand or high energy consumption times. How these “tariff energy containers”
are configured determines how fast these containers fill, which correlates to
increasing energy costs. The price per kWh is lowest at tariff T1 and highest at
tariff T2.
Multi-tariff implementation
The meter supports configuration of up to 4 different tariffs to measure and
monitor energy usage that can be used in billing or cost applications.
There are three different tariff modes you can use to activate the multi-tariff
registers:
• Command mode
• Time of Day mode
• Input mode
Active tariff control mode

The active tariff is controlled based on the tariff mode.
• When the meter is set to command mode, the active tariff is controlled by the
Modbus commands from your energy management system or other Modbus
master.
EAV15107-EN09 91
PowerLogic™ PM5300 series Multi-tariffs
• When the meter is set to input mode, the active tariff is controlled by the
status of the digital inputs.
• When the meter is set to time of day mode, the active tariff is controlled by the
day type, the start and end times, and the start and end dates.
Command mode overview

You can use command mode to send a Modbus command to the device which
sets the active tariff.
The active tariff is applied to the measured energy until you send another Modbus
command that sets a different tariff.
Search for your meter’s Modbus register list at www.se.com to download the
Modbus map.
Time of day mode overview

You can use time of day mode to create a tariff schedule that specifies where the
meter stores energy or input metered data, based on the time of year (month,
day), the type of day (every day, weekend, weekday or a specific day of the week),
or time of day.
The data collected from the different tariffs can then be used in energy audits or
similar costing and budget planning purposes.
Time of day mode tariff validity

A valid time of day tariff has certain conditions and limitations:
• Each tariff must cover a unique time period (tariffs cannot overlap), but there
can be periods with no tariff.
• Any number of tariffs, from none to the maximum number of tariffs, can be
applied.
• Time of day tariffs do not adjust for daylight savings time.
• Time of day tariffs include February 29th in leap years (however, it is not
recommended to have February 29th as a start or end date, as that tariff
would be invalid for non-leap years.
• Except for leap years, tariff dates are not year-specific; if you wanted to
create a tariff that starts on the first Monday in August, you need to enter the
date for that year, then manually update the tariff information for the
subsequent years.
Your device performs validation checks as you enter tariff information; it prompts
you to change the information that you have entered or set the tariff to disabled if
the tariff configuration is invalid. These checks can include:
• Start and end times must be different (for example, you cannot create a tariff
that starts at 02:00 and also ends at 02:00).
• Start time can only be earlier than end time for tariffs that are applied every
day. You can create a daily tariff that starts at 06:00 and ends at 02:00, but
these times are only valid for the Everyday tariff and invalid for the other tariff
types.
• Start day must be earlier than end day if the days are in the same month. You
cannot create a tariff that starts June 15 and ends June 12.
Time of day tariff creation methods

You can create time of day tariffs using one of the two methods, or a combination
of these methods:
92 EAV15107-EN09
• Time of year tariffs divide the year into multiple sections (usually seasons),
where each section has one or more day types. For example, a four tariff
configuration using this method could have Summer and Winter seasons that
also use different weekend and weekday tariffs.
• Daily tariffs can divide days by day of the week, a weekday, a weekend, or
every day, and can specify the time of day. For example, a four tariff
configuration could have every day in the year divided into six-hour tariff
periods or could have two tariffs for weekends and two tariffs for weekdays.
You can combine these methods if, for example you wanted to create a tariff that
applies on Mondays from January 1 to June 30, from 09:00 to 17:00. However,
since only one tariff can be applied at any time, you cannot use an everyday or
weekday tariff type because you already specified a tariff for the time periods
09:00 to 17:00.
Depending on how you configure the tariffs and the maximum number of tariffs
supported by your meter, you may not be able to assign tariffs for the entire year,
potentially leaving time gaps that do not have any tariff assigned to them.
Example tariff configurations for a four-tariff system

In these examples, four tariffs are used to cover the entire year (there are no time
periods that do not have an associated tariff).
Configuration 1: four tariffs with weekdays and weekends
Tariff Type Start date End date Start time End time
1 Weekend June 21 December 20 00:00 23:59

2 Weekend December 21 June 20 00:00 23:59
3 Weekday June 21 December 20 00:00 23:59
4 Weekday December 21 June 20 00:00 23:59
NOTE: The end time of 23:59 is actually 23:59:59, or just before midnight.
All weekend days fall into one of two different tariffs, depending on the date. All
weekdays fall into one of two different tariffs, depending on the date. This
configuration does not use tariffs based on the time of day, or any day types other
than weekend or weekday.
Example dates and corresponding tariffs:
• Friday, June 29 = tariff 3
• Sunday, November 28th = tariff 1
Configuration 2: one season for weekends, with off-peak and shoulder hours, two
seasons for weekdays, with shoulder hours
Tariff Type Start date End date Start time End time
1 Every day January 1 December 31 23:00 04:59
2 Weekdays May 1 September 20 00:00 22:59
3 Weekdays October 1 April 30 05:00 22:59
4 Weekends January 1 December 31 05:00 22:59
All days have a tariff applied between 23:00 and 04:59, corresponding to off-peak
hours. All weekend days have a tariff applied from 05:00 to 22:59, corresponding
to shoulder hours. All weekdays fall into one of two seasons (summer or winter),
and have two tariffs applied throughout the day.
Example dates and corresponding tariffs:
• Wednesday, March 21, 08:00 = tariff 3
• Tuesday, January 10, 21:00 = tariff 3
• Sunday, June 24, 14:00 = tariff 4
EAV15107-EN09 93
• Friday, August 17, 00:00 = tariff 1
Configuring time of day mode tariffs using the display

When the meter is set to time of day for tariffs, the active tariff is determined by the
day type, the start and end times, and the start and end dates.
The time of day tariff is not a calendar; the meter does not calculate the
corresponding day of the week to a specific date, but February 29th is considered
a valid date if you are programming the meter during a leap year.
When you enter tariff times using the front panel, be aware that the displayed
minute value includes the entire minute. For example, an end time of 01:15
includes the time from 01:15:00 through 01:15:59. To create a tariff period that
starts right after this, you must set the next tariff start time to 01:16. Although it
may appear that there is a gap between these tariffs, there is not.
3. Navigate to Meter > Tariff.
4. Select Mode and press Edit.
5. Press + or - to change the setting to Time of Day, then press OK.
6. Move the cursor to point to the tariff (Tariff 1 to Tariff 4) you want to modify,
then press Edit.
Day Type Everyday, Weekday, Select which day the tariff is

Weekend, Monday, Tuesday, active. Only tariffs that are
Wednesday, Thursday, Everyday can have a tariff
Friday, Saturday or Sunday that includes midnight (for
instance, from 11pm to 2am).
Start Time 0000 to 2359 Set the time when the tariff
period starts, using the 24
hour clock format (00:00 to
23:59). The Start Time
cannot equal the End Time.
End Time 0000 to 2359 Set the time when the tariff
period ends, using the 24
hour clock format (00:00 to
23:59). The End Time cannot
equal the Start Time.
Start Month 1 to 12 Set the month that the tariff

period starts, where 1 =
January, 2 = February, 3 =
March, 4 = April, 5 = May, 6 =
June, 7 = July, 8 = August, 9
= September, 10 = October,
11 = November, 12 =
December.
Start Day 1 to 31 Set the day of the Start
Month that the tariff period
starts. The Start Day must be
earlier than End Day if Start
Month equals End Month.
End Month 1 to 12 The month that the tariff

period ends, where 1 =
January, 2 = February, 3 =
March, 4 = April, 5 = May, 6 =
June, 7 = July, 8 = August, 9
= September, 10 = October,
11 = November, 12 =
December.
End Day 1 to 31 The day of the End Month
that the tariff period ends.
94 EAV15107-EN09
7. Modify each parameter as required, then press OK to set.

Press the Up and Down arrow buttons to move between parameters.
8. Press the Up arrow to exit, then Yes to save your changes.
Repeat for the other tariffs as required.
The meter checks the configuration and display a message if any tariffs have
conflicting settings (overlapping tariff periods for example).
Input mode overview

You can use input mode to have the digital inputs of the device set to know which
tariff is applied to the energy that is presently being consumed.
The number of different tariffs that can be applied is determined by the number of
available digital inputs and the total number of tariffs supported by your device.
Digital input assignment for input control mode

You need to assign one or more digital inputs with non-exclusive associations to
define the active tariff.
If a digital input is used for multi-tariff, it cannot be used for an exclusive
association (such as Demand Sync), but digital inputs can be shared with a non-
exclusive association (such as Alarms). To make a digital input available for
setting tariffs, any conflicting associations must be manually removed at the
source of the original association.
The digital inputs are used as binary counters to identify the appropriate tariff,
where off = 0 and on = 1, and most significant bit (MSB) is digital input 2 and least
significant bit (LSB) is digital input 1. By this definition, digital input 1 must be
associated with the multi-tariff feature in order to set the tariff to Input mode.
Digital input requirements for required number of tariffs
Number of Digital inputs required

tariffs required
Configuration 1 Configuration 2
1 1 (digital input 1) 1 (digital input 1)
2 1 (digital input 1) 2 (digital input 1 and 2)
3 2 (digital input 1 and 2) 2 (digital input 1 and 2)
4 2 (digital input 1 and 2) 2 (digital input 1 and 2)
Configuration 1: 2 tariff assignment using 2 digital inputs

NOTE: There is no inactive tariff with this configuration.
Tariff Digital input 2 Digital input 1
T1 0 0
T2 0 1
Configuration 2: 2 tariff assignment using 2 digital inputs

NOTE: Digital input configuration 00 means that there are no active tariffs (all
tariffs are disabled).
EAV15107-EN09 95
Tariff Digital input 2 Digital input 1
None 0 0
T1 0 1
T2 1 0
Configuring input mode tariffs using the display

Use the display to configure input mode tariffs. You can also configure input mode
tariffs using ION Setup.
You cannot configure any digital input tariff if digital input 1 is not available for
association. Likewise, digital input 2 must be available to select more than two
tariffs.
The status of the digital inputs is used to calculate the binary value of the active
tariff, where off = 0 and on = 1. The calculation of the number of tariffs value can
differ, depending on the number of digital inputs that can be selected (i.e., inputs
that can be associated with multi-tariff).
3. Navigate to Meter > Tariff.
4. Select Mode and press Edit.
5. Press + or - to change the setting to Input, then press OK.
NOTE: If a digital input association error prompt displays, you must exit
from the tariff setup screens and remove the digital input association.
6. Navigate to Tariffs, then press Edit.
7. Press + or - to change the number of tariffs you want to set up and press OK.
The maximum number of tariffs that you can apply is determined by the
number of available digital inputs.
8. Navigate to Inputs, then press Edit.
If applicable, press + or - to change how many digital inputs you want to use
to control which tariff is selected (active). Press OK.
9. Press the up arrow to exit, then Yes to save your changes.
96 EAV15107-EN09
Power quality PowerLogic™ PM5300 series
Power quality
Power quality measurements
The meter provides harmonic distortion metering up to the 31st harmonic.
The following power quality measurements are available:
• Individual harmonics (odd harmonics up to 31st)
• Total harmonic distortion (THD, thd) for current and voltage (line-to-line, line-
to-neutral)
• Total demand distortion (TDD)
The following harmonics data is available on the display:
• Numeric magnitude and angle of the fundamental (first) harmonic.
• Graphical display of the 3rd to 31st harmonics, expressed as a percentage of
the fundamental harmonic.
Harmonics overview
Harmonics are integer multiples of the fundamental frequency of the power
system.
Harmonics information is valuable for power quality analysis, determining properly
rated transformers, maintenance and troubleshooting. Evaluation of harmonics is
required for compliance to system power quality standards such as EN50160 and
meter power quality standards such as IEC 61000-4-30.
Harmonics measurements include per-phase magnitudes and angles (relative to
the fundamental frequency of the phase A voltage) for the fundamental and higher
order harmonics relative to the fundamental frequency. The meter’s power system
setting defines which phases are present and determines how line-to-line or line-
to-neutral voltage harmonics and current harmonics are calculated.
Harmonics are used to identify whether the supplied system power meets required
power quality standards, or if non-linear loads are affecting your power system.
Power system harmonics can cause current flow on the neutral conductor, and
damage to equipment such as increased heating in electric motors. Power
conditioners or harmonic filters can be used to minimize unwanted harmonics.
Total harmonic distortion %

Total harmonic distortion (THD%) is a measure of the total per-phase voltage or
current harmonic distortion present in the power system.
THD% provides a general indication of the quality of a waveform. THD% is
calculated for each phase of both voltage and current.
Total demand distortion

Total demand distortion (TDD) is the per-phase harmonic current distortion against
the full load demand of the electrical system.
TDD indicates the impact of harmonic distortion in the system. For example, if
your system is showing high THD values but a low demand, the impact of
harmonic distortion on your system might be insignificant. However at full load, the
THD value for the current harmonics is equal to TDD, so this could negatively
impact your system.
EAV15107-EN09 97
PowerLogic™ PM5300 series Power quality
Harmonic content calculations

Harmonic content (HC) is equal to the RMS value of all the non-fundamental
harmonic components in one phase of the power system.
The meter uses the following equation to calculate HC:
HC = (H2)2 + (H3)2 + (H4)2 ...
THD% calculations
THD% is a quick measure of the total distortion present in a waveform and is the
ratio of harmonic content (HC) to the fundamental harmonic (H1).
By default, the meter uses the following equation to calculate THD%:
HC
THD = -------
- x 100%
H1
thd calculations
thd is an alternate method for calculating total harmonic distortion that uses the
RMS value for the total harmonic content rather than the fundamental content.
The meter uses the following equation to calculate thd:
HC
thd = x 100
(H1)2 + (HC)2
TDD calculations
TDD (total demand distortion) evaluates the harmonic currents between an end
user and a power source.
The harmonic values are based on a point of common coupling (PCC), which is a
common point where each user receives power from the power source.
The meter uses the following equation to calculate TDD:
TDD = ( (HCIA)2 + (HCIB)2 + (HCIC)2) / (ILoad) x 100

Where ILoad is equal to the maximum demand load on the power system.
Viewing harmonics using the display

You can view harmonics data using the display.
1. Navigate to Harm.
The Harmonics % screen displays.
98 EAV15107-EN09
Power quality PowerLogic™ PM5300 series
2. Press the voltage or current harmonics you want to view.
IEEE mode IEC mode Description
V L-L U Line-to-line voltage harmonics data
V L-N V Line-to-neutral voltage harmonics data
Amps I Current harmonics data
TDD TDD Total demand distortion data
The fundamental (1st) harmonics numeric magnitudes and angles for all
phases are displayed.
3. Press 3–11, 13–21, or 21–31 to view the graphs for the 3rd to the 11th, 13th
to 21st, or 23rd to 31st harmonics, respectively.
For example, to display the 13th to 21st harmonics screen, press 13–21.
A Phase A B Phase B C Phase C
The vertical axis of the harmonics graph indicates the harmonic’s magnitude
as a percentage of the fundamental harmonic, and is scaled based on the
largest harmonic displayed. At the top of each vertical bar is a marker that
shows the maximum value of the harmonic. If the harmonic is greater than the
fundamental harmonic, this marker is triangular-shaped to show that the
value is out of range.
Viewing TDD using the display

The meter display provides screens that show TDD values.
NOTE: Your meter’s Modbus map includes registers for harmonics data for
integration into your power or energy management system. You can download
the Modbus register list of your meter at www.se.com.
1. Navigate to Harm > TDD.
The TDD information displays.
2. Press the up arrow to return to the main display screens.
Viewing THD/thd using the display

You can view THD/thd data using the display.
NOTE: Your meter’s Modbus map includes registers for total harmonic
distortion data for integration into your power or energy management system.
1. Navigate to THD to view the THD/thd Select screen.
EAV15107-EN09 99
PowerLogic™ PM5300 series Power quality
2. Press THD to display values that use the calculation method based on the
fundamental harmonic or thd to display values that use the calculation
method based on the RMS value of all harmonics in that phase (including the
fundamental).
IEEE mode IEC mode Description
Amps I Total harmonic distortion data for per phase

and neutral currents.
V L-L U Total harmonic distortion data line-to-line
voltage.
V L-N V Total harmonic distortion data line-to-neutral

voltage.
3. Press the current or voltage THD or thd values you want to view.
The total harmonic distortion percentage values are displayed.
4. Press the up arrow to return to the main display screens.
100 EAV15107-EN09
Maintenance PowerLogic™ PM5300 series
Maintenance
Maintenance overview
The meter does not contain any user-serviceable parts. If the meter requires
service, contact your local Schneider Electric Technical Support representative.
NOTICE
METER DAMAGE
• Do not open the meter case.
• Do not attempt to repair any components of the meter.
Failure to follow these instructions can result in equipment damage.
Do not open the meter. Opening the meter voids the warranty.
Power meter memory

The meter uses its nonvolatile memory to retain data and metering configuration
values.
Under the operating temperature range specified for the power meter this
nonvolatile memory has an expected life of at least 45 years.
NOTE: Life expectancy is a function of operating conditions and does not
constitute any expressed or implied warranty.
Firmware version, model and serial number

You can view the meter model, serial number, date of manufacture, firmware
version (including OS - Operating System and RS - Reset System), language
version, factory programmed MAC address* (ex: 9C-35-5B-5F-4C-4D), and OS
CRC (Cyclic Redundancy Check). The OS CRC value is a number (Hexadecimal
format) that identifies the uniqueness between different OS firmware versions.
* Only applicable for PM5320 / PM5340 / PM5341 meter models.
• Using the display panel: Navigate to Maint > Diag > Info.
Firmware upgrades
The power meter supports the downloading of new firmware and language files
over the communications link.
This requires the free DLF3000 software, which is available at www.se.com. The
DLF3000 offers an extensive Help file with information on operating the software.
The most recent firmware and language files are also available on the website.
Upgrading your meter using DLF3000

Use the DLF3000 upgrade utility, available from www.se.com, to upgrade your
meter’s firmware files.
NOTE: Recommended baud rate for firmware download through
communications link is 19200.
Before you begin, download the necessary files from www.se.com:
• Download the latest version of DLF3000 then install it on your computer.
• Download your meter’s firmware.
EAV15107-EN09 101
PowerLogic™ PM5300 series Maintenance
To see if there are firmware upgrades available for your meter, search for your
meter at www.se.com
1. Start DLF3000.
2. Click Add/Update.
3. Navigate to the folder where you saved your meter’s firmware then select the
firmware file and click Open.
4. Click Next.
5. Select a system to upgrade, or click New to define a new system.
6. Define the communications connection (click Add to create a new connection
or Configure to update an existing connection).
a. Type in the box to assign a communications connection name and select
a communications driver from the dropdown list (Modbus/TCP Driver or
Serial Driver).
b. Click Continue.
A dialog box appears where you need to provide the communications
information for the meter.
• If you are using Modbus over TCP to upgrade, type the meter’s IP
address in the box.
• If you are using a serial connection, enter the information on how
your meter is connected (such as communications wiring, parity,
port, address).
c. Click OK.
7. Define the devices to upgrade.
a. Click Add.
b. Type in a device name.
c. Select the device type from the list.
d. Select the connection name for the communications connection used
with the device (the one you defined in the previous step).
e. Click OK.
f. Enter in the device address and protocol information then click OK.
8. Click Next.
9. Select the device name from the Download Candidate Devices pane, then
click the right arrow button to move the selection to the Download Target
Devices pane.
10. Select the meter firmware in the Firmware to field.
11. Click Next.
12. Click Health Check to confirm the meter is communicating.
The Health Status shows Passed to indicate successful communications.
13. Click Next.
The Firmware Update Group shows the connection name, the firmware
version and status (should be “Queued”). The Group Device List shows the
device or devices being upgraded.
14. Click Download.
NOTE: A warning message displays, “Warning: Relays on PowerLogic
Metering Devices will be de-energized if selected for download and will
remain in this mode until a successful download is completed. Press OK
to start the download.”
102 EAV15107-EN09
15. Click OK.

• The Firmware Upgrade Group status changes to Active, then updates to
show the current upgrade progress (in percent complete).
• The Group Device List status shows “Entering Download Mode”, then
changes to “Downloading” when the firmware is being downloaded to the
meter. “Estimated Time Remaining” shows the firmware download
progress.
• You can also check the progress on meters equipped with a display
panel. The meter display shows “Download in progress” and a shows a
dynamically incrementing number for “Percent Complete” (up to 100%).
When the firmware upgrade is complete, the Firmware Update Group status
shows Complete (Passed). The Group Device List status shows Successful
Download.
16. Click Finished.
To exit the download firmware program, click Yes when prompted to quit DLF.
Diagnostics information
The diagnostics screen provides meter information, status and event data for
troubleshooting.
Navigate to Maint > Diag > Meter to view details of the meter status.
Navigate to Maint > Diag > Cl Pwr to view the control power information.
• Non-MID meter models : The Cl Pwr screen displays how many times the
meter lost control power, and the date and time of its last occurrence.
• MID meter models : The Cl Pwr screen displays how many times the meter
lost control power (auxiliary power), and the last power up and power down
events with the timestamp.
Navigate to Maint > Diag > PhAng to view the graphical representation of the
power system the meter is monitoring.
Control power (auxiliary power) interruption event

For MID compliant models.
When the meter is in OFF state and control power supply is applied OR when the
meter is in ON state and the control power is cycled:
• If the 4-digit MID/Revenue Lock is enabled, an icon which indicates the

control power loss blinks on the top right corner of the screen.
• When the meter is in ON state and the control power goes below the
operating range, the meter logs the Last Power Down event with timestamp
before power-off.
• When the meter is in OFF state and the control power is applied, the meter
logs the Last Power Up event with timestamp after power-on.
• When there are multiple events along with control power interruption event,
then the control power interruption event icon blinks taking precedence over
all other icons.
NOTE: The meter displays only the Number of Losses, the Last Power
Down and Last Power Up events. The last 20 control power interruption
event logs (10 Power Down and 10 Power Up events) can be read only
through communication.
Acknowledging control power (auxiliary power) interruption event using the display
For MID compliance on applicable models.
EAV15107-EN09 103
NOTE: When the control power interruption event icon displays on the meter,
the facility manager must assess the reason and its duration.
Use the Cl Pwr screen to acknowledge the control power interruption event.
You can acknowledge (dismiss) the control power interruption event only after
entering the 4-digit MID/Revenue Lock password.
NOTE:
• You cannot acknowledge the alarms and the control power interruption
events at the same time.
• The control power interruption event icon blinks until you

acknowledge the Number of Losses, the Last Power Up and Last
Power Down events.
1. Navigate to Maint > Diag > Cl Pwr.
The Number of Losses, the Last Power Up and Last Power Down events
with the timestamp are displayed on the same page.
2. Press Ack.
3. Enter the Revenue Lock password, then press OK.
NOTE: The default password is 0000.
4. Read the Attention! message on the display and press Yes to acknowledge
or press No to go back to previous screen.
The Ack and control power interruption event icon disappears only
when you press Yes.
NOTE: You can reset the Number of Losses to 0 only through the
Modbus communication. To perform this reset, you need to disable the 4-
digit MID/Revenue Lock password in the meter HMI.
Troubleshooting
LED indicators
Abnormal heartbeat / serial communications LED behavior could mean potential
problems with the meter.
Problem Probable causes Possible solutions

LED flash rate does not Communications wiring If using a serial-to-RS-485
change when data is sent from converter, trace and check that
the host computer. all wiring from the computer to
the meter is properly
terminated.
Internal hardware problem Perform a hard reset: turn off
control power to the meter,
then re-apply power. If the
problem persists, contact
Technical Support.
Heartbeat / serial Internal hardware problem Perform a hard reset: turn off
communications LED remains control power to the meter,
lit and does not flash ON and then re-apply power. If the
OFF problem persists, contact
Technical Support.
Heartbeat / serial Display setup parameters Review display parameter

communications LED flashes, incorrectly set setup.
but the display is blank.
If the problem is not fixed after troubleshooting, contact Technical Support for
help. Make sure you have your meter’s firmware version, model and serial number
information available.
104 EAV15107-EN09
Troubleshooting checks
There are some checks you can perform to try to identify potential issues with the
meter’s operation.
The following table describes potential problems, their possible causes, checks
you can perform or possible solutions for each. After referring to this table, if you
cannot resolve the problem, contact your local Schneider Electric sales
representative for assistance.
DANGER
standards.
• This equipment must be installed and serviced only by qualified personnel.
is off.
otherwise.
Potential problem Possible cause Possible solution
The maintenance (wrench) When the maintenance Go to Maint > Diag. Event
icon is illuminated on the (wrench) icon is illuminated, it messages display to indicate
power meter display. indicates an event has the reason the icon is
occurred which may require illuminated. Note these event
attention. messages and call the
Technical Support or contact
your local sales representative
for assistance.
The display is blank after The power meter may not be The display may have timed
applying control power to the receiving the necessary power. out. Verify that the power meter
power meter. line and terminals are receiving
the necessary power. Verify
that the heartbeat LED is
blinking. Press a button to see
if the display timed out.
The data being displayed is • Incorrect setup values. • Check that the correct
inaccurate or not what you • Incorrect voltage inputs. values have been
expect. entered for power meter
• Power meter is wired setup parameters (CT
improperly and VT ratings, Nominal
Frequency, and so on).
• Check power meter
voltage input terminals
(1, 2, 3, 4) to verify that
adequate voltage is
present.
• Check that all CTs and
VTs are connected
correctly (proper polarity
is observed) and that
they are energized.
Check shorting terminals.
See the recommended
torque in the Wiring
section of the installation
manual.
EAV15107-EN09 105
Potential problem Possible cause Possible solution
Cannot communicate with • Power meter address is • Check to see that the
power meter from a remote incorrect. power meter is correctly
personal computer. • Power meter baud rate is addressed.
incorrect. • Verify that the baud rate
• Communications lines of the power meter
are improperly matches the baud rate of
connected. all other devices on its
communications link.
• Communications lines
are improperly • Verify the power meter
terminated. communications
connections.
• Incorrect route statement
to power meter. • Check to see that a multi-
point communications
terminator is properly
installed.
• Check the route
statement. Contact
Global Technical Support
for assistance.
Energy/Alarm LED not May have been disabled by Confirm that the energy / alarm
working. user. LED is configured correctly.
Technical assistance
Visit www.se.com for support and assistance with lost passwords or other
technical problems with the meter.
Make sure you include your meter’s model, serial number and firmware version in
your email or have it readily available if calling Technical Support.
106 EAV15107-EN09
Verifying accuracy PowerLogic™ PM5300 series
Verifying accuracy
Overview of meter accuracy
All meters are tested and verified at the factory in accordance with International
Electrotechnical Commission (IEC) and American National Standards Institute
(ANSI) standards.
Your digital power meter typically does not require re-calibration. However, in
some installations a final accuracy verification of the meters is required, especially
if the meters will be used for revenue or billing applications.
For a list of accuracy standards that your meter complies to, contact your local
Schneider Electric representative or download the meter brochure from
www.se.com.
Accuracy test requirements

The most common method for testing meter accuracy is to apply test voltages and
currents from a stable power source and compare the meter’s readings with
readings from a reference device or energy standard.
Signal and power source

The meter maintains its accuracy during voltage and current signal source
variations but its energy pulsing output needs a stable test signal to help produce
accurate test pulses. The meter’s energy pulsing mechanism needs
approximately 10 seconds to stabilize after every source adjustment.
The meter must be connected to control power in order to conduct accuracy
verification testing. Refer to your meter’s installation documentation for power
supply specifications.
DANGER
Verify the device’s power source meets the specifications for your device’s
power supply.
Control equipment
Control equipment is required for counting and timing the pulse outputs from an
energy pulsing LED or digital output.
• Most standard test benches have an arm equipped with optical sensors to
detect LED pulses (the photodiode circuitry converts detected light into a
voltage signal).
• The reference device or energy standard typically has digital inputs that can
detect and count pulses coming from an external source (i.e., the meter’s
digital output).
NOTE: The optical sensors on the test bench can be disrupted by strong
sources of ambient light (such as camera flashes, florescent tubes, sunlight
reflections, floodlights, etc.). This can cause test errors. Use a hood, if
necessary, to block out ambient light.
EAV15107-EN09 107
PowerLogic™ PM5300 series Verifying accuracy
Environment
The meter should be tested at the same temperature as the testing equipment.
The ideal temperature is about 23 ºC (73 ºF).
A warm-up time of 30 minutes is recommended before beginning energy accuracy
verification testing. At the factory, the meters are warmed up to their typical
operating temperature before calibration to help ensure that the meters will reach
their optimal accuracy at operating temperature.
Most high precision electronic equipment requires a warm up time before it
reaches its specified performance levels.
Reference device or energy standard

To help ensure the accuracy of the test, it is recommended that you use a
reference device or reference energy standard with a specified accuracy that is 6
to 10 times more accurate than the meter under test. Before you start testing, the
reference device or energy standard should be warmed up as recommended by
the manufacturer.
NOTE: Verify the accuracy and precision of all measurement equipment used
in accuracy testing (for example, voltmeters, ammeters, power factor meters).
Energy pulsing
You can configure the meter’s alarm /energy LED or the digital output(s) for
energy pulsing.
• The meter is equipped with an alarm / energy pulsing LED. When configured
for energy pulsing, the LED emits pulses that are then used to determine the
accuracy of the meter’s energy measurements.
• The meter sends the pulses from the configured digital output(s) port, which
are then used to determine the accuracy of the meter’s energy
measurements by pulse counter.
Meter settings for accuracy testing

Your meter‘s power system and other parameters must be configured for accuracy
testing.
Meter parameter Value
Power system 3PH4W Wye Gnd (3-phase, 4 wire Wye with

ground)
Energy pulse constant In sync with reference test equipment
(alarm/energy pulsing LED or digital output)
Verifying accuracy test

The following tests are guidelines for accuracy testing your meter; your meter
shop may have specific testing methods.
108 EAV15107-EN09
DANGER
standards.
is off.
• Verify the device’s power source meets the specifications for your device’s
power supply.
1. Turn off all power supplying this device and the equipment in which it is
installed before working on the device or equipment.
2. Use a properly rated voltage sensing device to confirm that all power is off.
3. Connect the test voltage and current source to the reference device or energy
standard. Ensure all voltage inputs to the meter under test are connected in
parallel and all current inputs are connected in series.
A Reference device or energy standard
B Test voltage and current source
C Meter under test
4. Connect the control equipment used for counting the standard output pulses
using one of these methods:
Option Description
Energy pulsing LED Align the red light sensor on the standard test bench armature over
the energy pulsing LED.
Digital output Connect the meter’s digital output to the standard test bench pulse
counting connections.
NOTE: When selecting which method to use, be aware that energy

pulsing LEDs and digital output(s) have different pulse rate limits.
5. Before performing the verification test, let the test equipment power up the
meter and apply voltage for at least 30 seconds. This helps stabilize the
internal circuitry of the meter.
6. Configure the meter’s parameters for verifying accuracy testing.
EAV15107-EN09 109
7. Depending on the method selected for counting the energy pulses, configure
the meter’s energy pulsing LED or one of the digital output(s) to perform
energy pulsing. Set the meter’s energy pulse constant so it is in sync with the
reference test equipment.
8. Perform accuracy verification on the test points. Run each test point for at
least 30 seconds to allow the test bench equipment to read an adequate
number of pulses. Allow 10 seconds of dwell time between test points.
Required pulses calculation for accuracy verification testing

Accuracy verification test equipment typically requires you to specify the number
of pulses for a specific test duration.
The reference test equipment typically requires you to specify the number of
pulses required for a test duration of “t” seconds. Normally, the number of pulses
required is at least 25 pulses, and the test duration is greater than 30 seconds.
Use the following formula to calculate the required number of pulses:
Number of pulses = Ptot x K x t/3600
Where:
• Ptot = total instantaneous power in kilowatts (kW)
• K = the meter’s pulse constant setting, in pulses per kWh
• t = test duration, in seconds (typically greater than 30 seconds)
Total power calculation for accuracy verification testing

Accuracy verification testing supplies the same test signal (total power) to both the
energy reference/standard and the meter under test.
Total power is calculated as follows, where:
• Ptot = total instantaneous power in kilowatts (kW)
• VLN = test point line-to-neutral voltage in volts (V)
• I = test point current in amps (A)
• PF = power factor
The result of the calculation is rounded up to the nearest integer.
For a balanced 3–phase Wye system:
Ptot = 3 x VLN x I x PF x 1 kW/1000 W
NOTE: A balanced 3–phase system assumes that the voltage, current and
power factor values are the same for all phases.
For a single-phase system:
Ptot = VLN x I x PF x 1 kW/1000W
Percentage error calculation for accuracy verification testing

Accuracy verification testing requires you to calculate the percentage error
between the meter being tested and the reference/standard.
Calculate the percentage error for every test point using the following formula:
Energy error = (EM - ES) / ES x 100%
Where:
• EM = energy measured by the meter under test
• ES = energy measured by the reference device or energy standard.
NOTE: If accuracy verification reveals inaccuracies in your meter, they may be
caused by typical sources of test errors. If there are no sources of test errors
present, please contact your local Schneider Electric representative.
110 EAV15107-EN09
Accuracy verification test points

The meter should be tested at full and light loads and at lagging (inductive) power
factors to help ensure testing over the entire range of the meter.
The test amperage and voltage input rating are labeled on the meter. Refer to the
installation sheet or data sheet for your meter’s nominal current, voltage and
frequency specifications.
Watt-hour test point Sample accuracy verification test point
Full load 100% to 200% of the nominal current, 100% of the nominal voltage and
nominal frequency at unity power factor or one (1).
Light load 10% of the nominal current, 100% of the nominal voltage and nominal
frequency at unity power factor or one (1).
Inductive load (lagging 100% of the nominal current, 100% of the nominal voltage and nominal
power factor) frequency at 0.50 lagging power factor (current lagging voltage by 60°
phase angle).
VAR-hour test point Sample accuracy verification test point
Full load 100% to 200% of the nominal current, 100% of the nominal voltage and
nominal frequency at zero power factor (current lagging voltage by 90°
phase angle).
Light load 10% of the nominal current, 100% of the nominal voltage and nominal
frequency at zero power factor (current lagging voltage by 90° phase
angle).
Inductive load (lagging 100% of the nominal current, 100% of the nominal voltage and nominal
power factor) frequency at 0.87 lagging power factor (current lagging voltage by 30°
phase angle).
Energy pulsing considerations

The meter’s alarm / energy LED and digital output(s) are capable of energy
pulsing within specific limits.
Description Alarm / energy LED Digital output
Maximum pulse frequency 2.5 kHz 25 Hz
Minimum pulse constant 1 pulse per k_h
Maximum pulse constant 9,999,999 pulses per k_h
The pulse rate depends on the voltage, current and PF of the input signal source,
the number of phases, and the VT and CT ratios.
If Ptot is the instantaneous power (in kW) and K is the pulse constant (in pulses
per k_h), then the pulse period is:
3600 1
Pulse period (in seconds) = =
K x Ptot Pulse frequency (Hz)
VT and CT considerations
Total power (Ptot) is derived from the values of the voltage and current inputs at
the secondary side, and takes into account the VT and CT ratios.
The test points are always taken at the secondary side, regardless of whether VTs
or CTs are used.
If VTs and CTs are used, you must include their primary and secondary ratings in
the equation. For example, in a balanced 3-phase Wye system with VTs and CTs:
EAV15107-EN09 111
VTp CTp 1 kW
Ptot = 3 x VLN x xIx x PF x
VTs CTs 1000 W
where Ptot = total power, VTp = VT primary, VTs = VT secondary, CTp = CT
primary, CTs = CT secondary and PF = power factor.
Total power limits

There are limits to the total power that the alarm / energy pulsing LED and the
digital output can handle.
Total power limit for alarm / energy LED

Given the maximum pulse constant (Kmax) you can enter is 9,999,999 pulses per
kWh, and the maximum pulse frequency for the alarm / energy LED is 83 Hz, the
maximum total power (Max Ptot) the alarm / energy LED’s energy pulsing circuitry
can handle is 29.88 Watts:
• Maximum Ptot = 3600 x (Maximum pulse frequency) / Kmax = 3600 x 83 /
9,999,999 = 0.02988 kW
Total power limit for digital output

Given the maximum pulse constant (Kmax) you can enter is 9,999,999 pulses per
kWh, and the maximum pulse frequency for the digital output is 25 Hz, the
maximum total power (Max Ptot) the digital output’s energy pulsing circuitry can
handle is 9 Watts:
• Maximum Ptot = 3600 x (Maximum pulse frequency) / Kmax = 3600 x 25 /
9,999,999 = 0.009 kW
Typical sources of test errors

If you see excessive errors during accuracy testing, examine your test setup and
test procedures to eliminate typical sources of measurement errors.
Typical sources of accuracy verification testing errors include:
• Loose connections of voltage or current circuits, often caused by worn-out
contacts or terminals. Inspect terminals of test equipment, cables, test
harness and the meter under test.
• Meter ambient temperature is significantly different than 23 °C (73 °F).
• Floating (ungrounded) neutral voltage terminal in any configuration with
unbalanced phase voltages.
• Inadequate meter control power, resulting in the meter resetting during the
test procedure.
• Ambient light interference or sensitivity issues with the optical sensor.
• Unstable power source causing energy pulsing fluctuations.
• Incorrect test setup: not all phases connected to the reference device or the
energy standard. All phases connected to the meter under test should also be
connected to the reference meter/standard.
• Moisture (condensing humidity), debris or pollution present in the meter under
test.
112 EAV15107-EN09
MID compliance PowerLogic™ PM5300 series
MID compliance
MID-compliant models
The PM5331/PM5341 meter models are compliant to the Measuring Instruments
Directive.
Protected setup parameters and functions

Your meter has features and settings that cannot be changed while the meter is
revenue-locked. In order to prevent modifications to revenue-related settings and
data on your meter, some of the features and parameters on your meter cannot be
edited once the meter is revenue-locked.
Protected setup parameters
Settings Protected Description

status
Power system settings Yes You cannot change any power system settings
while the meter is locked (for example, power
system type, VT and CT connections, VT and CT
primary and secondary values, system
frequency and phase rotation)
NOTE: For MID compliance, the Power
System must be set to either 3PH4W Wye
Gnd (three-phase 4-wire wye grounded) or
3PH3W Dlt Ungnd (three-phase 3-wire
delta ungrounded)
Meter label Yes You cannot change the meter label while the
meter is locked
Meter time settings Yes You cannot change the meter’s date while the
meter is locked
Energy pulsing Yes The alarm / energy pulsing LED on the MID-
compliant models is permanently set for energy
pulsing and cannot be disabled or used for
alarms. All other setup parameters for the
energy pulsing LED are also permanently set
and cannot be modified.
Energy reset password Yes You cannot change the energy reset password
while the meter is locked
Protected functions
After the meter is locked, the following resets are disabled:
• Global resets: Meter Initialization (all) and Energies
• Single resets: Energy and Multi-Tariff
For a complete list of protected functions and settings, see your meter’s Modbus
register list, available from www.se.com.
Locking or unlocking the meter

After you initialize the meter, you must lock it in order to conform to MID
standards.
Before you lock your meter:
• Make sure you have completed all necessary configuration.
• Perform a meter initialization reset to clear any previously accumulated meter
data.
EAV15107-EN09 113
PowerLogic™ PM5300 series MID compliance
A lost lock password cannot be recovered.
NOTICE
PERMANENTLY LOCKED DEVICE
1. Navigate to Maint > Setup > Meter > Lock.

2. Press Edit to activate or deactivate the lock.
3. Enter your lock password.
NOTE: The default password is 0000.
4. Press + and - to scroll between Active and Inactive.
5. Press OK to select the option.
6. Select Yes to confirm the selected option, and exit the screen.
7. Make sure you record and store the lock password in a secure location.
On activating the lock, a lock icon appears on the upper left corner of the
screen.
NOTE: Make sure you record and store the lock password in a secure
location. A lost lock password cannot be recovered.
Setting up the lock password

You can change the lock password on the meter.
NOTE: You cannot change the lock password when the lock is active. To
change the password, make sure the lock is inactive.
A lost lock password cannot be recovered.
NOTICE
PERMANENTLY LOCKED DEVICE
1. Navigate to Maint > Setup > HMI > Pass.

2. Press the down arrow to scroll to Passwords > Revenue Lock screen.
3. Press Edit to select a password.
4. Press + to increment the active digit through the numerals 0-9.
5. Press the left arrow to move to the next digit to the left.
6. Continue until all values are selected, and then press OK to set the password.
7. Press Yes to save the changes.
114 EAV15107-EN09
Device specifications PowerLogic™ PM5300 series
Device specifications
The specifications contained in this section are subject to change without notice.
Mechanical characteristics
IP degree of protection (IEC 60529) Display: IP54 (Upgrade to IP65 with optional accessory kit METSEIP65OP96X96FF)
Meter body: IP30
Mounting position Vertical
Display type Monochrome graphics LCD, 128 x 128 resolution
Display backlight White LED
Viewable area 67 x 62.5 mm (2.64 x 2.46 in)
Weight 430 g
Dimensions W x H x D [protrusion from 96 x 96 x 72 mm (depth of meter from housing mounting flange) [13 mm]
cabinet]
Panel thickness 6 mm maximum
Electrical characteristics
Measurement accuracy
• Measurement type: True RMS on three-phase (3P, 3P + N); 64 samples per cycle, zero blind
• IEC 61557-12: PMD/[SD|SS]/K70/0.5 (for firmware version 1.1.1 and higher)
Measurement type Class of accuracy as per IEC 61557-12 (for firmware version 1.1.1 Error
and higher)
Active energy Class 0.5S (Class 0.5S as per IEC 62053-22 at 5 A Inominal (for 1 A ±0.5%
Inominal when I > 0.15 A))
Reactive energy Class 2 (Class 2 as per IEC 62053-23 at 5 A Inominal (for 1 A Inominal ±2%
when I > 0.15 A))
Apparent energy Class 0.5 ±0.5%
Active power Class 0.5 ±0.5%
Reactive power Class 2 ±2%
Apparent power Class 0.5 ±0.5%
Current Class 0.5 ±0.5%
Voltage (L-N) Class 0.5 ±0.5%
Frequency Class 0.05 ±0.05%
Power factor Class 0.5 ±0.005 Count
Power quality accuracy
Measurement type Class of accuracy as per IEC 61557-12 (for firmware version 1.1.1 Error
and higher)
Voltage harmonics Class 5 ±5%
Voltage THD/thd Class 5 ±5%
Current harmonics Class 5 ±5%
Current THD Class 5 ±5%
EAV15107-EN09 115
PowerLogic™ PM5300 series Device specifications
Voltage inputs
Maximum VT/PT primary 1.0 MV AC
Specified accuracy range 20 – 400 V L-N / 35 – 690 V L-L (Wye) or 35 – 600 V L-L (Delta)
UL Listed up to 347 V L-N / 600 V L-L
(absolute range 35 V L-L to 760 V L-L)
Overload 460 V L-N / 800 V L-L

Impedance 5 MΩ
Frequency Measured: 45 to 65 Hz
Nominal: 50 / 60 Hz
Burden < 0.2 VA at 240 V AC L-N
Current inputs
CT secondary Nominal: 5 A or 1 A
Measured current 5 mA to 8.5 A

Starting current 5 mA
Withstand 20 A continuous
50 A at 10 sec/hr
500 A at 1 sec/hr
Impedance < 0.3 mΩ
Frequency Measured: 45 to 65 Hz
Nominal: 50 / 60 Hz
Burden < 0.026 VA at 8.5 A
AC control power
Operating range 100 – 277 V AC L-N / 100 – 415 V L-L ±10%
Installation category CAT III 300 V L-N class per IEC 61010
Burden 5 W / 11 VA max at 415 V AC
4 W max at 125 V DC
Frequency 50/60 Hz ± 5 Hz
Ride-through time 80 ms typical at 120V AC and maximum burden
100 ms typical at 230 V AC and maximum burden
100 ms typical at 415 V AC and maximum burden
DC control power
Operating range 125 – 250 V DC ±20%
Burden < 4 W at 250 V DC

Ride-through time 50 ms typical at 125 V DC and maximum burden
Mechanical outputs
Number 2 (selected models)
Maximum output frequency 0.5 Hz maximum (1 second ON / 1 second OFF – minimum times)
Switching current 250 V AC at 8.0 Amps, 25 k cycles, resistive
30 V DC at 2.0 Amps, 75 k cycles, resistive
30 V DC at 5.0 Amps,12.5 k cycles, resistive
Isolation 2.5 kV rms
116 EAV15107-EN09
Digital outputs
Number 2
Maximum load voltage 40 V DC
Maximum load current 20 mA

ON resistance 50 Ω maximum
Pulse frequency ≤ 25 Hz
Meter constant from 1 to 9,999,999 pulses per k_h (k_h = kWh, kVARh or kVAh depending on the energy
parameter selected)
Pulse width 50% duty cycle
Leakage current 0.3 micro Amps
Isolation 5 kV rms
Status inputs
Number 2
Voltage OFF 0 - 4 V DC
Voltage ON 18.5 - 36 V DC
Frequency 2 Hz (T ON min = T OFF min = 250 ms)
Input resistance 110 kΩ
Isolation 5 kV rms
Response time 20 ms
Whetting output 24 V DC/ 8mA max
Input burden 2 mA @ 24 V DC
Environmental characteristics
Operating temperature Meter: -25 to 70 °C (-13 to 158 °F)
Display: -20 to 70 °C (-4 to 158 °F)
Display functions to -25 ºC (-13 °F) with reduced performance
Storage temperature -40 to 85 °C (-40 to 185 °F)
Humidity rating Operating: 5 – 95% RH non-condensing
Pollution degree 2
Altitude 2000 m CAT III / 3000 m CAT II

Location Not suitable for wet locations
For indoor use only
Product life > 15 years
LEDs
LED indicators
Heartbeat / communications activity Green LED
Alarm / energy pulsing LED Amber LED
EAV15107-EN09 117
PowerLogic™ PM5300 series Device specifications
Type Amber LED, optical
Maximum pulse frequency 50 Hz
Pulse width 50% duty cycle (200 μs minimum ON time)
Meter constant from 1 to 9,999,999 pulses per k_h (k_h = kWh, kVARh or kVAh depending on the energy
parameter selected)
Fixed at 10,000 pulses per kWh on MID meter models
Wavelength 590 to 635 nm
EMC (electromagnetic compatibility)

Product standards IEC 61557-12 (IEC 61326-1), IEC 62052-11 and EN50470
Immunity to electrostatic discharge IEC 61000-4-2
Immunity to radiated fields IEC 61000-4-3
Immunity to fast transients IEC 61000-4-4
Immunity to surges IEC 61000-4-5
Immunity to voltage dips and IEC 61000-4-11

interruptions
Immunity to magnetic fields IEC 61000-4-8
Immunity to conducted disturbances, IEC 61000-4-6

150kHz to 80MHz
Radiated and conducted emissions FCC part 15 Class B, EN55022 Class B
Safety
Europe CE, as per IEC 61010-1 (3rd Edition), IEC 62052- 11 & IEC 61557-12 (for firmware version 1.1.1
and higher)
U.S. and Canada cULus as per UL61010-1 (3rd Edition)
CAN/CSA-C22.2 No. 61010-1 (3rd Edition)
Measurement category (voltage and CAT III up to 400 V L-N / 690 V L-L
current inputs)
Dielectric As per IEC/UL 61010-1 (3rd Edition)
Protective class Protective Class II
Double insulated for user-accessible parts
MID compliance
Additional specifications apply to the MID meter models (PM5331 and PM5341).
Applicable MID standards and class

• EN 50470-1:2006 Class C
index
• EN 50470-3:2006 Class C
Type of measuring equipment Static watt-hour meter
Intended use Indoor use only, permanently mounted in residential, commercial or light industrial applications,
where levels of vibration and shock are of low significance
Mechanical environment M1
Electromagnetic (EMC) environment E2
118 EAV15107-EN09
Applicable measurements C(kWh)
Voltage at voltage terminals

• 3-phase 4-wire Wye grounded: 3 x 63.5(110) to 3 x 277(480) V AC
• 3-phase 3-wire Delta ungrounded: 3 x 110 to 3 x 480 V L-L
Current Rating (Imin – Iref (Imax)) 0.05-5(6) A
Electrical network frequency 50 Hz
Impulse voltage rating 6 kV
AC voltage rating 4 kV
Main cover sealing type Wire and crimp
RS-485 communications
Number of ports 1 (optional)
Maximum cable length 1219 m (4000 ft)
Maximum number of devices (unit Up to 32 devices on the same bus

loads)
Parity Even, Odd, None (1 stop bit for Odd or Even parity; 2 stop bits for None)
Baud rate 9600, 19200, 38400 baud
Protocol Modbus RTU, Modbus ASCII (7 or 8 bit), JBUS
Isolation 2.5 kV RMS, double insulated
Ethernet communications
Number of ports 1 (optional)
Data rate up to 100 Mbps
Protocol Modbus TCP and BACnet/IP
EAV15107-EN09 119
PowerLogic™ PM5300 series China Standard Compliance
China Standard Compliance

This product complies with the following standard(s) in China:
IEC 62053-22:2003 Electricity metering equipment (a.c.) - Particular requirements - Part 22: Static
meters for active energy (classes 0,2 S and 0,5 S)
IEC 61557-12:2007 Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500
V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 12:
Performance measuring and monitoring devices
GB/T 22264.7-2008 安装式数字显示电测量仪表第7部分：多功能仪表的特殊要求
120 EAV15107-EN09
Schneider Electric
35 rue Joseph Monier
92500 Rueil Malmaison
France
+ 33 (0) 1 41 29 70 00
www.se.com
As standards, specifications, and design change from time to time,

please ask for confirmation of the information given in this publication.
© 2021 – Schneider Electric. All rights reserved.

EAV15107-EN09

Schneider 5330

Uploaded by

Copyright:

Available Formats

Schneider 5330

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Schneider 5330

Uploaded by

Copyright:

Available Formats

PowerLogic™ PM5300 series

The addition of either symbol to a “Danger” or “Warning” safety label indicates

BACnet/IP communications implementation..........................................45

Harmonic content calculations ...................................................................98

PM5310 PM5320 PM5330 PM5340

Accuracy IEC 61557-12 Cl 0.5S Cl 0.5S Cl 0.5S Cl 0.5S

I/O 2SI/2DO 2SI/2DO 2SI/2DO 2SI/2DO

Single and multi-condition alarms ✔ ✔ ✔ ✔

Communications: Serial ports with Modbus protocol 1 — 1 —

Communications: Ethernet port with Modbus TCP — 1 — 1

Functions and characteristics

Use on LV and MV systems ✔

Basic metering with THD and min/max readings ✔

Instantaneous rms values

Current (per phase and neutral) ✔

Voltage (total, per phase L-L and L-N) ✔

Displacement PF (Total and per phase) Signed, Four Quadrant

% Unbalanced I, V L-N, V L-L ✔

Accumulated Active, Reactive and Apparent Received/Delivered; Net and absolute

Current average1 Present, Last, Predicted, Peak, and Peak Date

Synchronization of the measurement window to ✔

Configurable demand intervals ✔

1Stored in non-volatile memory

Power quality measurements

THD, thd (Total Harmonic Distortion) I, V L-N, V I, V L-N, V L-L

TDD (Total Demand Distortion) ✔

Individual harmonics (odds) 31st

Alarm counters and alarm logs ✔

1Stored in non-volatile memory

Min/max of instantaneous values, plus phase ✔

Memory capacity 256 kB

Maintenance, alarm and event logs ✔

1Stored in non-volatile memory

Form A Relay outputs 2

Timestamp resolution in seconds 1

Data display and analysis tools

Power SCADA Operation

Modbus command interface

E Status inputs/Digital outputs

F Communication port (Ethernet or RS-485)

LED indicators on the display

A Alarm / energy pulsing LED (orange)

B Heartbeat / communications LED (green)

Alarm / energy pulsing LED

Heartbeat / serial communications LED

Ethernet communications LEDs

Panel-mount meter mounting and wiring recommendations

Meter wiring considerations

Single-phase 2-wire 1PH2W LN 347 V L-N 400 V L-N 1 VT

Single-phase 2-wire 1PH2W LL 600 V L-L 600 V L-L 1 VT

3-phase 3-wire 3PH3W Dlt Ungnd 600 V L-L 600 V L-L 2 VT

3-phase 3-wire 3PH3W Dlt Crnr 600 V L-L 600 V L-L 2 VT

Balanced system considerations

Balanced 3-phase Wye system with 2 CTs

Balanced 3-phase Wye or Delta system with 1CT

- Data minus. This transmits/receives the inverting data signals.

+ Data plus. This transmits/receives the non-inverting data signals.

Ethernet communications connections

A Navigation / menu selection

C Alarm / energy pulsing LED