PROJECT : 34M STADIUM MAST - PHILIPS INDIA LIMITED

DESCRIPTION: D-28/SM/TLL PILE CAP DESIGN FOR COMPRESSION

COL. MKD.: TYPE Silty clay (Water Table encountered at GL m depth)

Pedestal Size
Width b = 1.50 (m)
Length l = 1.50 (m) Fck = 25 (N/mm^2) Safe in Punching shear
Height bl. Gl h = 0.80 (m) Fy = 500 (N/mm^2) FAIL in flexure at bottom
Height ab. Gl h' = 0.30 (m) OK in flexural at top
Pile Diameter D = 0.60 (m) Fail in One Way shear
Pile Length L = 13.00 (m) SAFE in combined stress
size of Pile Cap Pt -bot = 0.22 (%)
b = 3.40 (m) Pt-top = 0.16 (%)
l = 3.40 (m) Cover= 60 (mm)
d = 0.60 (m) RCC:-
Dead Wt cap + PaWf = 23.53 (T) 9.41
Sub Dead wt pileWp = 4.79 (T)

Concrete unit wt. γCONC = 2.500 T/Cu.m PCC= 1.03 Cu.m.

Soil unit wt. γsoil = 1.800 T/Cu.m Wsoil= 12.19 (T) EXCAVATION= 24.34 Cu.m.
Depth of pedestaDftg = 1.10 (m) Angle of Int. Friction, φ = θ = 14.00 degree

Pitch Distance 4.00 x pile dia

FACTORED LOADS LOAD ON PILE (compression / Tension) Resultant

LONG VERT TRANS TRANS LONG Shear
LOAD Fx Fy Fz Mx Mz Pd PILE -1 PILE-2 PILE-3 PILE-4 Each Pile
CASE (T) (T) (T) (T-m) (T-m) (T) T T T T T
CASE 1 0.00 0.08 9.08 162.42 0.00 13.74 -23.31 50.79 50.79 -23.31 9
0.00

Max Compressive Force (T) -23.31 50.79 50.79 -23.31 2.2695209

Max Tensile Force ( T) -23.31 50.79 50.79 -23.31

X Axis

1100.00
p1 p2 1700.0

0.95 600
Z Axis

p4 p3
1.50

0.500 2.40 0.500

600.00
 Table 1
CHECK FOR PUNCHING : Steel Mulim/(fckbd2)
250.00 0.149
Maximum Comp Force on pile = 498.30 Kn 415.00 0.138
Width of Pile cap = 3400 mm 500.00 0.133
Depth of Pile Cap D = 600 mm 500.00 0.133
Effective depth De = 540 mm

Maximum stress in Punching = 0.23 (N/mm^2)

Permissible stress in shear 1.25 (N/mm^2) Safe in Punching shear

CHECK FOR MOMENT CAPACITY OF PILE CAP

Max Moment M = (2 x Pmax )x ( B/2-b/2) 96.51 T.m 44.29 T.m

F.O.S. 1.00 Mu 946.76 Kn.m 434.5 Kn.m

since, Mu= factor* fck b d^2

Depth required = dreq 289.39 mm Safe, Singly r/f 196.04 Safe, Singly r/f

FLEXURE CAPACITY AT BOTTOM: FLEXURE CAPACITY AT TOP:

Muxx = 96.51 (T-m) Muxx = 44.29 (T-m)
Astreq= 4227.1 sqmm Astreq= 1889.3 sqmm
Pt = 0.22 (%) Pt = 0.16 (%)
Mrxx = 90.69 (T-m) Mrxx = 66.79 (T-m)
FAIL in flexure at bottom OK in flexural at top
Astx= 4039 (mm^2) Astx= 2938 (mm^2)

Bottom Steel Top Steel

412892.45
Dia of Bar: mm 20.00 16.00 7128.00
Rebar area : mm^2 314.16 201.06 420020.45
Rebar Wt. : kg/m 2.47 1.58 4.20
No. of Rebars : 13 15
Spacing of Bar in : mm 250.00 220.00 4.81

CHECK FOR ONE-WAY SHEAR : β =0.8*fck/6.89*Pt = 13.194353

CHECK ALONG X-X τc = 0.345 Mpa
Vux'= 996.6 (Kn)
Arx= 2.04 (m^2)
Tvx= 0.489 (N/mm^2)
τc = 0.345 (N/mm^2)
Fail in One Way shear
 DESIGN OF PEDESTAL
SIZE OF PEDESTAL --------- B --------- 1.50 X 1.50 M
LENGTH OF PEDESTAL -----------PL------- 1.10 M
L/D RATIO 0.73 <3.0

ULTIMATE FORCES ON PEDESTAL

VERTICAL FORCES = Pu = 0.81 KN
HORIZONTAL FORCE =Hz = 89.06 KN
MOMENT = Muxx= 1691 KN.M
MOMENT = Muzz= 0.00 KN.M

CHECK FOR CONCRETE SECTION ONLY

3 3
SECTIONAL MODULUS OF PEDESTAL = Z = 1/6 X B 5.6E+08 MM
2
SECTIONAL AREA OF PEDESTAL = Ap = 2250000 MM

STRESS IN COMP = σ cc, cal =P/A 0.00 Mpa

STRESS IN BENDING = σ bc, cal =M/Z 3.01 Mpa

PERMISSIBLE STRESS IN CONCRETE:

STRESS IN COMP =σ cc, per 5.00 Mpa
STRESS IN BENDING =σ bc, per 7.00 Mpa

COMBINED STRESS RATIO = ( σ cc,cal/σ cc,per + σ bc,cal / σ bc,per) 0.43 < 1.0
SAFE in combined stress

Pu / (Fck x B x d) 0.0000

d' / D REFER DESIGN AIDS OF CONCRETE, CHART-43 0.03

P/Fck IS VERY SMALL, THEREFORE PROVIDE MIN 0.15% OF STEEL.

Pt 0.30

Column No. L (mm) b (mm) D (mm) DIA OF BARS PROVIDED 16.00

Size of Column 1100.00 1500 1500 NOS OF BARS PROVIDED 36.00
Final Moments Mx 1691.26 KN-m Ast 7238.23
My 0.00 KN-m
Axial Load Pu 0.81 KN 8.00 TOR STIRRUPS 8.00 200.00 MM
fck (N/mm2) 25 d' 50 mm PROVIDE 16 TOR- 36 NOS OF LONGITUDINAL REINFORCEMENT & 8 TOR STIRRUPS @ 200C/C.
fy (N/mm2) 500

Provided Pt 0.322
Pt/fck 0.013
Pu/(fck . b . D) 0.00

From value of Pt/fck and Pu/(fck . b . D) choose apprpriate value of

Muy/(fck . b . D2) and Muz/(fck . b . D2) from SP - 16

d'/D 0.05
Mux/(fck . b . D^2) 0.110
Mux1 9281.25 kNm Safe
d'/B 0.05
Muy/(fck . b . D2) 0.110
Muy1 9281.25 kNm Safe

2
Area of Conc. Ac (mm ) 2242762
2
Area of Steel Ast (mm ) 7238.23
Puz 0.45 . fck . Ac + 0.75 . fy . As 27945 KN
Pu/Puz 0.000 an 1.000
an an
Check (Mux/Mux1) + (Muy/Muy1) 0.182
an an
(Muy/Muy1) + (Muz/Muz1) < 1 so Design is SAFE