WCS Murano

DRIVER INFORMATION & MULTIMEDIA
SECTION
WARNING CHIME SYSTEM
WCS B
E
CONTENTS
BASIC INSPECTION .................................... 3 PARKING BRAKE RELEASE WARNING CHIME F
: System Description ................................................11
DIAGNOSIS AND REPAIR WORKFLOW .......... 3 PARKING BRAKE RELEASE WARNING CHIME
Work Flow ................................................................. 3 : Component Parts Location ....................................12 G
PARKING BRAKE RELEASE WARNING CHIME
FUNCTION DIAGNOSIS ............................... 5 : Component Description .........................................12
WARNING CHIME SYSTEM ............................... 5 KEY WARNING CHIME .............................................12 H
KEY WARNING CHIME : System Diagram .............13
WARNING CHIME SYSTEM ....................................... 5
KEY WARNING CHIME : System Description ........13
WARNING CHIME SYSTEM : System Diagram ...... 5
KEY WARNING CHIME : Component Parts Loca- I
WARNING CHIME SYSTEM : System Description
tion ...........................................................................14
...... 5
KEY WARNING CHIME : Component Description....14
WARNING CHIME SYSTEM : Component Parts
Location ..................................................................... 6 DIAGNOSIS SYSTEM (METER) ....................... 15 J
WARNING CHIME SYSTEM : Component De- CONSULT-III Function (METER/M&A) ....................15
scription ..................................................................... 7
DIAGNOSIS SYSTEM (BCM) ........................... 19 K
LIGHT REMINDER WARNING CHIME ....................... 7
LIGHT REMINDER WARNING CHIME : System COMMON ITEM .........................................................19
Diagram ..................................................................... 7 COMMON ITEM : CONSULT-III Function (BCM -
LIGHT REMINDER WARNING CHIME : System COMMON ITEM) .....................................................19 L
Description ................................................................ 7
LIGHT REMINDER WARNING CHIME : Compo- BUZZER .....................................................................20
nent Parts Location ................................................... 8 BUZZER : CONSULT-III Function (BCM - BUZZ-
M
LIGHT REMINDER WARNING CHIME : Compo- ER) ..........................................................................20
nent Description ........................................................ 8
COMPONENT DIAGNOSIS ......................... 22
SEAT BELT WARNING CHIME .................................. 8 WCS
SEAT BELT WARNING CHIME : System Diagram
POWER SUPPLY AND GROUND CIRCUIT .... 22
...... 9 COMBINATION METER ............................................22
SEAT BELT WARNING CHIME : System Descrip- COMBINATION METER : Diagnosis Procedure ....22 O
tion ............................................................................ 9
SEAT BELT WARNING CHIME : Component BCM (BODY CONTROL MODULE) ..........................22
Parts Location ......................................................... 10 BCM (BODY CONTROL MODULE) : Diagnosis
Procedure ................................................................22 P
SEAT BELT WARNING CHIME : Component De-
scription ................................................................... 10
METER BUZZER CIRCUIT ............................... 24
PARKING BRAKE RELEASE WARNING CHIME .... 10 Description ...............................................................24
PARKING BRAKE RELEASE WARNING CHIME Component Function Check ....................................24
: System Diagram .................................................... 11 Diagnosis Procedure ..............................................24
Revision: 2008 October WCS-1 2009 Murano

SEAT BELT BUCKLE SWITCH SIGNAL CIR- THE PARKING BRAKE RELEASE WARNING
CUIT ................................................................... 25 CONTINUES SOUNDING, OR DOES NOT
Description .............................................................. 25 SOUND .............................................................. 94
Component Function Check ................................. 25 Description .............................................................. 94
Diagnosis Procedure ............................................. 25 Diagnosis Procedure ............................................... 94
Component Inspection ............................................ 26
THE LIGHT REMINDER WARNING DOES
WARNING CHIME SYSTEM ............................. 27 NOT SOUND ...................................................... 95
Wiring Diagram - WARNING CHIME - .................... 27 Description .............................................................. 95
Diagnosis Procedure ............................................... 95
ECU DIAGNOSIS ........................................ 32
THE SEAT BELT WARNING CONTINUES
COMBINATION METER .................................... 32 SOUNDING, OR DOES NOT SOUND ............... 96
Reference Value ..................................................... 32
Description .............................................................. 96
Wiring Diagram - METER - ..................................... 37
Diagnosis Procedure ............................................... 96
Fail-Safe ................................................................. 47
DTC Index .............................................................. 48 THE KEY WARNING DOES NOT SOUND ....... 97
Description .............................................................. 97
BCM (BODY CONTROL MODULE) .................. 49 Diagnosis Procedure ............................................... 97
Reference Value ..................................................... 49
Wiring Diagram - BCM - ......................................... 73 PRECAUTION ............................................ 98
Fail-safe .................................................................. 87
DTC Inspection Priority Chart .............................. 90 PRECAUTIONS ................................................. 98
DTC Index .............................................................. 91 Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SYMPTOM DIAGNOSIS ............................. 94 SIONER" ................................................................. 98

DIAGNOSIS AND REPAIR WORKFLOW
< BASIC INSPECTION >
BASIC INSPECTION A
Work Flow INFOID:0000000003452014
B
OVERALL SEQUENCE
C
JSNIA0456GB M
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM WCS
Interview the customer to obtain as much information as possible about the conditions and environment under
which the malfunction occurred.
O
>> GO TO 2.
2.CHECK SYMPTOM P
• Check the symptom based on the information obtained from the customer.
• Check if any other malfunctions are present.
>> GO TO 3.
3.CHECK CONSULT-III SELF-DIAGNOSIS RESULTS
Connect CONSULT-III and perform self-diagnosis. Refer to MWI-34, "CONSULT-III Function (METER/M&A)".

< BASIC INSPECTION >
Are self-diagnosis results normal?
YES >> GO TO 4.
NO >> GO TO 5.
4.NARROW DOWN MALFUNCTIONING PARTS BY SYMPTOM DIAGNOSIS
Perform symptom diagnosis and narrow down the malfunctioning parts.
>> GO TO 5.
5.REPAIR OR REPLACE MALFUNCTIONING PARTS
Repair or replace malfunctioning parts.
NOTE:
If DTC is displayed, erase DTC after repairing or replacing malfunctioning parts.
>> GO TO 6.
6.FINAL CHECK
Check that the warning buzzer in the combination meter operates normally.
Does it operate normally?
YES >> INSPECTION END
NO >> GO TO 1.

< FUNCTION DIAGNOSIS >
FUNCTION DIAGNOSIS A
B
WARNING CHIME SYSTEM : System Diagram INFOID:0000000003452017
JPNIA1556GB
J
WARNING CHIME SYSTEM : System Description INFOID:0000000003465221
K
COMBINATION METER
• The buzzer (1) for the warning chime system is integrated in the
combination meter.
L
• The combination meter sounds the alarm buzzer installed in the
combination meter when receiving the buzzer output signal trans-
mitted from each unit.
M
WCS
JPNIA0741ZZ
BCM O
BCM receives signals from various units and transmits a buzzer output signal to the combination meter via
CAN communication if it judges that the warning buzzer should be activated.
BCM Warning Function List P

Warning functions Signal name

• Ignition switch signal
Light reminder warning chime • Lighting switch position signal
• Door switch signal (driver side)
• Ignition switch signal
Seat belt warning chime
• Seat belt buckle switch signal (driver side)
• Ignition signal
Key warning chime • Key slot switch signal
• Door switch signal (driver side)
NOTE:
Parking brake release warning chime is detected by combination meter.
WARNING CHIME SYSTEM : Component Parts Location INFOID:0000000003452019
JPNIA0814ZZ
Combination switch
1. Front door switch (driver side) 2. 3. Parking brake
(Lighting switch)
4. Seat belt buckle switch (driver side) 5. Key slot 6. BCM
7. Combination meter
A. Behind the combination meter

WARNING CHIME SYSTEM : Component Description INFOID:0000000003452020
Unit Description
• Receives a buzzer output signal from the BCM with CAN communication line and sounds the B
buzzer.
• Judges whether the parking brake is released from the vehicle speed signal received from the
Combination meter ABS actuator and electric unit (control unit) with CAN communication line and the parking
brake switch signal from the parking brake switch, and sounds the buzzer if necessary. C
• Receives the seat belt buckle switch signal (driver side) from the seat belt buckle switch (driver
side) and transmits it to BCM with CAN communication line.
BCM
Transmits signals provided by various units to the combination meter with CAN communication D
line.
ABS actuator and electric unit
Transmits the vehicle speed signal to combination meter with CAN communication line.
(control unit) E
Seat belt buckle switch (driver
Transmits a seat belt buckle switch signal (driver side) to the combination meter.
side)
Combination switch F
Transmits the lighting switch position signal to BCM.
(Lighting switch)
Front door switch
Transmits the door switch signal (driver side) to BCM.
(driver side)
G
Parking brake switch Refer to MWI-54, "Description".
Key slot Transmits the key slot switch signal to BCM.
H
LIGHT REMINDER WARNING CHIME
LIGHT REMINDER WARNING CHIME : System Diagram INFOID:0000000003452021
JPNIA0749GB
L
LIGHT REMINDER WARNING CHIME : System Description INFOID:0000000003465397
DESCRIPTION M
With ignition switch in the OFF or ACC position, when the driver door is open and the lighting switch is the 1st
or 2nd position, the light warning chime will sound.
• BCM detects ignition switch in the OFF or ACC position, front door switch (driver side) ON, and lighting WCS
switch in 1st or 2nd position. Then the BCM transmits the buzzer output signal (light reminder warning
chime) to combination meter with CAN communication line.
• When combination meter receives buzzer output signal (light reminder warning chime), it sounds the buzzer.
O
WARNING OPERATION CONDITIONS
If all of the following conditions are fulfilled.
• Ignition switch is in the OFF or ACC P
• Lighting switch is in the 1st or 2nd position
• Front door switch (driver side) is ON
WARNING CANCEL CONDITIONS
Warning is canceled if any of the following conditions is fulfilled.
• Lighting switch OFF
• Ignition switch ON
• Front door switch (driver side) is OFF

LIGHT REMINDER WARNING CHIME : Component Parts Location INFOID:0000000003508997
JPNIA0814ZZ
Combination switch
(Lighting switch)
LIGHT REMINDER WARNING CHIME : Component Description INFOID:0000000003465398
Unit Description
Combination meter Receives a buzzer output signal from the BCM and sounds the buzzer.
Judges the light warning conditions from the signals provided by various switches and transmits a
BCM
buzzer output signal to the combination meter via CAN communication line if necessary.
Combination switch
Transmits the lighting switch position signal to BCM.
(Lighting switch)
Front door switch (driver side) Transmits the door switch signal (driver side) to BCM.
SEAT BELT WARNING CHIME

SEAT BELT WARNING CHIME : System Diagram INFOID:0000000003452025
E
JPNIA0750GB
SEAT BELT WARNING CHIME : System Description INFOID:0000000003465318

F
DESCRIPTION
With ignition switch turned ON and driver seat belt unfastened, seat belt warning chime will sound for approxi- G
mately 6 seconds.
• The combination meter receives the seat belt buckle switch signal (driver side) from seat belt buckle switch
(driver side) and transmits it to the BCM via CAN communication. H
• The BCM receives seat belt buckle switch signal (driver side) from combination meter via CAN communica-
tion.
• The BCM detects seat belt reminder warning based on the received signal and transmits the buzzer output
I
signal to combination meter via CAN communication.
• The combination meter receives the buzzer output signal from BCM via CAN communication and sounds the
warning buzzer.
J
If all of the following conditions are fulfilled, the warning buzzer will sound.
• Seat belt buckle switch (driver side) is ON (driver seat belt not fastened) K

Warning is canceled if any of the following conditions are fulfilled. L
• Ignition switch OFF
• Seat belt buckle switch (driver side) is OFF (driver seat belt fastened)
WCS

SEAT BELT WARNING CHIME : Component Parts Location INFOID:0000000003508998
JPNIA0814ZZ
Combination switch
(Lighting switch)
SEAT BELT WARNING CHIME : Component Description INFOID:0000000003465346
Unit Description
• Receives the seat belt buckle switch signal (driver side) from the seat belt buckle switch (driver
Combination meter side) and transmits it to BCM via CAN communication line.
• Receives a buzzer output signal from the BCM and sounds the buzzer.
Judges the seat belt warning condition according to the seat belt buckle switch signal (driver side)
BCM received from the combination meter via CAN communication and transmits a buzzer output signal
to the combination meter via CAN communication line if necessary.
Seat belt buckle switch
Transmits the seat belt buckle switch signal (driver side) to the combination meter.
(driver side)
PARKING BRAKE RELEASE WARNING CHIME

PARKING BRAKE RELEASE WARNING CHIME : System Diagram INFOID:0000000003465347
JPNIA0751GB
D
PARKING BRAKE RELEASE WARNING CHIME : System Description INFOID:0000000003465450
E
DESCRIPTION
Parking brake release warning chime judges the remaining parking brake according to the vehicle speed sig-
nal received from the ABS actuator and electric unit (control unit) via CAN communication and the parking
brake switch signal from parking brake switch to sound the warning buzzer. F
If all of the following conditions are fulfilled. G
• Vehicle speed is 7 km/h (4.3 MPH) or higher
• Parking brake switch ON
WARNING CANCEL CONDITIONS H
Warning is canceled if any of the following conditions are fulfilled.

• Vehicle speed is approximately 3 km/h (1.9 MPH) or less
• Parking brake switch OFF I
WCS

PARKING BRAKE RELEASE WARNING CHIME : Component Parts Location
INFOID:0000000003509000
JPNIA0814ZZ
Combination switch
(Lighting switch)
PARKING BRAKE RELEASE WARNING CHIME : Component Description INFOID:0000000003465451
Unit Description
Judges the remaining parking brake according to the vehicle speed signal received from the ABS
Combination meter actuator and electric unit (control unit) via CAN communication and the parking brake switch signal
from parking brake switch and sounds the warning buzzer.
ABS actuator and electric unit
Transmits the vehicle speed signal to the combination meter via CAN communication.
(control unit)
Parking brake switch Transmits the parking brake switch signal to the combination meter.
KEY WARNING CHIME

KEY WARNING CHIME : System Diagram INFOID:0000000003465350
JPNIA1557GB
D
KEY WARNING CHIME : System Description INFOID:0000000003465351
E
DESCRIPTION
• BCM detects key warning according to the input of ignition switch, key slot switch signal and door switch
(driver side) signal and transmits the buzzer output signal via CAN communication.
• The combination meter receives the buzzer output signal from BCM and sounds the warning buzzer. F
If all of the following conditions are fulfilled, the chime will sound.
• Other than ignition switch ON G
• Key switch ON (keyfob is inserted in key slot)
• Front door switch (driver side) ON
H
Warning canceled if any of the following conditions are fulfilled.
• Key switch OFF (keyfob is not inserted in key slot) I
• Front door switch (driver side) OFF
WCS

KEY WARNING CHIME : Component Parts Location INFOID:0000000003509005
JPNIA0814ZZ
Combination switch
(Lighting switch)
KEY WARNING CHIME : Component Description INFOID:0000000003465353
Unit Description
Sounds the warning buzzer according to the buzzer output signal received from BCM via CAN
Combination meter
communication.
Judges key warning according to the door switch signal (driver side) from the front door switch
BCM (driver side) and the key slot switch signal from the key slot and transmits the buzzer output signal
to the combination meter via CAN communication.
Front door switch (driver side) Transmits the door switch signal (driver side) to BCM.
Key slot Transmits the key slot switch signal to BCM.

DIAGNOSIS SYSTEM (METER)
A
CONSULT-III Function (METER/M&A) INFOID:0000000003452069
CONSULT-III APPLICATION ITEMS B

CONSULT-III can perform the following diagnosis modes via CAN communication and the combination meter.
System Diagnosis mode Description C

Self Diagnostic Result The combination meter checks the conditions and displays memorized errors.
METER/M&A Data Monitor Displays the combination meter input/output data in real time.
Special function Lighting history of the warning lamp and indicator lamp can be checked. D
SELF DIAG RESULT

Refer to WCS-48, "DTC Index". E
DATA MONITOR
Display Item List
F
X: Applicable
MAIN
Display item [Unit] Description
SIGNALS
G
Value of vehicle speed signal received from ABS actuator and electric unit (control
SPEED METER unit) via CAN communication.
X
[km/h] NOTE:
655.35 is displayed when the malfunction signal is received. H
Vehicle speed signal value transmitted to other units via CAN communication.
SPEED OUTPUT
X NOTE:
[km/h]
655.35 is displayed when the malfunction signal is received. I
ODO OUTPUT
Odometer signal value transmitted to other units via CAN communication.
[km/h or mph]
TACHO METER
Value of the engine speed signal received from ECM via CAN communication. J
X NOTE:
[rpm]
8191.875 is displayed when the malfunction signal is received.
FUEL METER K
X Fuel level indicated on combination meter.
[L]
Value of engine coolant temperature signal is received from ECM via CAN com-
W TEMP METER munication.
X L
[°C] NOTE:
215 is displayed when the malfunction signal is input.
ABS W/L Status of ABS warning lamp detected from ABS warning lamp signal is received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication. M
Status of VDC OFF indicator lamp detected from VDC OFF indicator lamp signal
VDC/TCS IND
is received from ABS actuator and electric unit (control unit) via CAN communica-
[On/Off]
tion. WCS
SLIP IND Status of SLIP indicator lamp detected from slip indicator lamp signal received
[On/Off] from ABS actuator and electric unit (control unit) via CAN communication.
Status of brake warning lamp detected from brake warning lamp signal is received O
from ABS actuator and electric unit (control unit) via CAN communication.
BRAKE W/L
NOTE:
[On/Off]
Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON. P
DOOR W/L Status of door warning detected from door switch signal received from BCM via
[On/Off] CAN communication.
HI-BEAM IND Status of high beam indicator lamp detected from high beam request signal is re-
[On/Off] ceived from BCM via CAN communication.
TURN IND Status of turn indicator lamp detected from turn indicator signal is received from
[On/Off] BCM via CAN communication.

MAIN
SIGNALS
LIGHT IND Status of light indicator lamp detected from position light request signal is received
[On/Off] from BCM via CAN communication.
OIL W/L Status of oil pressure warning lamp detected from oil pressure switch signal is re-
MIL Status of malfunction indicator lamp detected from malfunctioning indicator lamp
[On/Off] signal is received from ECM via CAN communication.
CRUISE IND Status of CRUISE indicator detected from ASCD status signal is received from
[On/Off] ECM via CAN communication.
O/D OFF IND Status of O/D OFF indicator detected from O/D OFF indicator signal is received
[On/Off] from control device.
4WD W/L Status of AWD warning lamp detected from AWD warning lamp signal is received
[On/Off] from AWD control unit via CAN communication.
4WD LOCK IND Status of AWD LOCK warning lamp detected from AWD LOCK warning lamp sig-
[On/Off] nal is received from AWD control unit via CAN communication.
FUEL W/L
Low-fuel warning lamp status detected by the identified fuel level.
[On/Off]
WASHER W/L Status of washer warning lamp judged from washer level switch input to combina-
[On/Off] tion meter.
AIR PRES W/L Status of low tire pressure warning lamp detected from tire pressure signal is re-
KEY G/W W/L Status of key warning lamp (G/Y) detected from key warning signal is received
[On/Off] from BCM via CAN communication.
LCD
[B&P N, B&P I, ID NG, ROTAT, SFT Displays status of Intelligent Key system warning detected from meter display sig-
P, INSRT, BATT, NO KY, OUTKY, LK nal is received from BCM via CAN communication.
WN]
SHIFT IND Status of shift position indicator detected from shift position signal is received from
[P, R, N, D, L] TCM via CAN communication.
O/D OFF SW
Status of O/D OFF switch.
[On/Off]
M RANGE SW
This item is displayed, but cannot be monitored.
[Off]
NM RANGE SW
[Off]
AT SFT UP SW
[Off]
AT SFT DWN SW
[Off]
ST SFT UP SW
[Off]
ST SFT DWN SW
[Off]
PKB SW
Status of parking brake switch.
[On/Off]
BUCKLE SW
Status of seat belt buckle switch (driver side).
[On/Off]
BRAKE OIL SW
Status of brake fluid level switch.
[On/Off]
DISTANCE
Value of possible driving distance calculated by combination meter.
[km]
A/C AMP CONN
Status of A/C auto amp. connection recognition signal.
[On/Off]

MAIN
SIGNALS A
ENTER SW
[On/Off] Status of (ENTER) switch.
SELECT SW B
[On/Off] Status of (SELECT) switch.
Ambient air temperature value converted from ambient sensor signal received
from ambient sensor. C
OUTSIDE TEMP NOTE:
[°C or °F] This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the ambient
sensor input value.) D
FUEL LOW SIG Status of fuel level low warning signal to output to AV control unit via CAN com-
[On/Off] munication.
Buzzer status (in the combination meter) is detected from the buzzer output signal E
BUZZER
X received from each unit via CAN communication and the warning output condition
[On/Off]
of the combination meter.
NOTE: F
Some items are not available according to vehicle specification.
SPECIAL FUNCTION
G
Special menu
Display item Description H

W/L ON HISTORY Lighting history of warning lamp and indicator lamp can be checked.
W/L ON HISTORY
• Stores histories when warning/indicator lamp is turned on. I
• “W/L ON HISTORY” indicates the “TIME” when the warning/indicator lamp is turned on.
• The “TIME” above is :
- 0 : The condition that the warning/indicator lamp has been turned on 1 or more times after starting the J
engine and waiting for 30 seconds.
- 1 - 39 : The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY : Stores NO (0) turning on history of warning/indicator lamp.
K
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking the brake is applied or the brake fluid level
gets low. L
Display Item
Display item Description M

ABS W/L Lighting history of ABS warning lamp.
VDC/TCS IND Lighting history of VDC OFF indicator lamp.
WCS
SLIP IND Lighting history of SLIP indicator lamp.
BRAKE W/L Lighting history of brake warning lamp.
DOOR W/L Lighting history of door warning. O
TRUNK/GLAS-H This item is displayed, but cannot be monitored.
OIL W/L Lighting history of oil pressure warning lamp.
P
C-ENG W/L Lighting history of malfunction indicator lamp.
C-ENG2 W/L This item is displayed, but cannot be monitored.
CRUISE IND Lighting history of CRUISE indicator lamp.
SET IND Lighting history of SET indicator.
CRUISE W/L This item is displayed, but cannot be monitored.
BA W/L This item is displayed, but cannot be monitored.

Display item Description
O/D OFF IND Lighting history of O/D OFF indicator lamp.
ATC/T-AMT W/L This item is displayed, but cannot be monitored.
ATF TEMP W/L This item is displayed, but cannot be monitored.
CVT IND This item is displayed, but cannot be monitored.
SPORT IND This item is displayed, but cannot be monitored.
4WD W/L Lighting history of AWD warning lamp.
FUEL W/L Lighting history of low fuel level warning.
WASHER W/L Lighting history of low washer fluid warning
AIR PRES W/L Lighting history of low tire pressure warning lamp.
KEY G/Y W/L Lighting history of key warning lamp (green/yellow).
KEY R W/L Lighting history of key warning lamp (red).
KEY KNOB W/L This item is displayed, but cannot be monitored.
SYS FAIL W/L This item is displayed, but cannot be monitored.
SFT POSI W/L This item is displayed, but cannot be monitored.
HV BAT W/L This item is displayed, but cannot be monitored.
HEV BRAKE W/L This item is displayed, but cannot be monitored.
SFT OPER W/L This item is displayed, but cannot be monitored.
CHAGE W/L Lighting history of charge warning lamp.
OIL LEV LOW This item is displayed, but cannot be monitored.
DPF W/L This item is displayed, but cannot be monitored.

DIAGNOSIS SYSTEM (BCM)
A
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) INFOID:0000000003514555
B
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
C
Diagnosis mode Function Description
Work Support Changes the setting for each system function.
D
Self Diagnostic Result Displays the diagnosis results judged by BCM.
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
CAN Diag Support Monitor
tion manual.
E
Data Monitor The BCM input/output signals are displayed.
Active Test The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification The BCM part number is displayed. F
• Read and save the vehicle specification.
Configuration
• Write the vehicle specification when replacing BCM.
SYSTEM APPLICATION G
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items. H
×: Applicable item
Diagnosis mode
System Sub system selection item
Work Support Data Monitor Active Test I
Door lock DOOR LOCK × × ×
Rear window defogger REAR DEFOGGER × ×
J
Warning chime BUZZER × ×
Interior room lamp timer INT LAMP × × ×
Remote keyless entry system MULTI REMOTE ENT* 1 × × × K
Exterior lamp HEAD LAMP × × ×
Wiper and washer WIPER ×*2 × ×
L
Turn signal and hazard warning lamps FLASHER × × ×
— AIR CONDITONER*3
• Intelligent Key system
M
INTELLIGENT KEY × × ×
• Engine start system
Combination switch COMB SW ×
WCS
Body control system BCM ×
NVIS - NATS IMMU × ×
Interior room lamp battery saver BATTERY SAVER × × × O
Back door opener system TRUNK × ×
Vehicle security system THEFT ALM × × ×
RAP system RETAINED PWR × P
Signal buffer system SIGNAL BUFFER × ×
TPMS TPMS (AIR PRESSURE MONITOR) × × ×
NOTE:
• *1: At models with Intelligent Key system this item is displayed, but is not used.
• *2: At models with rain sensor this mode is displayed, but is not used.

• *3: This item is displayed, but is not used.
FREEZE FRAME DATA (FFD)

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
CONSULT screen item Indication/Unit Description

Vehicle Speed km/h Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter km Total mileage (Odometer value) of the moment a particular DTC is detected
While turning BCM status from low power consumption mode to
SLEEP>LOCK
normal mode (Power supply position is “LOCK”)
While turning BCM status from low power consumption mode to
SLEEP>OFF
normal mode (Power supply position is “OFF”.)
LOCK>ACC While turning power supply position from “LOCK” to “ACC”
ACC>ON While turning power supply position from “ACC” to “IGN”
While turning power supply position from “RUN” to “ACC” (Vehicle
RUN>ACC
is stopping and selector lever is except P position.)
While turning power supply position from “CRANKING” to “RUN”
CRANK>RUN
(From cranking up the engine to run it)
While turning power supply position from “RUN“ to “ACC” (Emer-
RUN>URGENT
gency stop operation)
ACC>OFF While turning power supply position from “ACC” to “OFF”
OFF>LOCK While turning power supply position from “OFF” to “LOCK”
Power position status of
OFF>ACC While turning power supply position from “OFF” to “ACC”
Vehicle Condition the moment a particular
ON>CRANK DTC is detected While turning power supply position from “IGN” to “CRANKING”
While turning BCM status from normal mode (Power supply posi-
OFF>SLEEP
tion is “OFF”.) to low power consumption mode
While turning BCM status from normal mode (Power supply posi-
LOCK>SLEEP
tion is “LOCK”.) to low power consumption mode
Power supply position is “LOCK” (Ignition switch OFF with steer-
LOCK
ing is locked.)
Power supply position is “OFF” (Ignition switch OFF with steering
OFF
is unlocked.)
ACC Power supply position is “ACC” (Ignition switch ACC)
Power supply position is “IGN” (Ignition switch ON with engine
ON
stopped)
Power supply position is “RUN” (Ignition switch ON with engine
ENGINE RUN
running)
CRANKING Power supply position is “CRANKING” (At engine cranking)
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
IGN Counter 0 - 39 • The number increases like 1 → 2 → 3...38 → 39 after returning to the normal condition
whenever ignition switch OFF → ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
BUZZER
BUZZER : CONSULT-III Function (BCM - BUZZER) INFOID:0000000003452035
CONSULT-III APPLICATION ITEMS
Test item Diagnosis mode Description

Data Monitor Displays BCM input data in real time.
BUZZER
Active Test Operation of electrical loads can be checked by sending driving signal to them.

DATA MONITOR
A
Display item
Description
[Unit]
PUSH SW B
Status of push button ignition switch judged by BCM.
[On/Off]
UNLK SEN-DR
Status of unlock sensor judged by BCM.
[On/Off] C
VEH SPEED 1 Value of vehicle speed signal received from ABS actuator and electric unit (control unit) with CAN
[Km/h] communication line.
KEY SW-SLOT D
Status of key slot judged by BCM.
[On/Off]
TAIL LAMP SW
Status of each switch judged by BCM using the combination switch readout function.
[On/Off]
E
FR FOG SW
Status of front fog lamp switch judged by BCM.
[On/Off]
DOOR SW-DR F
Status of driver side door switch judged by BCM.
[On/Off]
ACTIVE TEST
G
Display item
Description
[Unit]
IGN KEY WARN ALM The key warning chime operation can be checked by operating the relevant function (On/Off). H
SEAT BELT WARN TEST The seat belt warning chime operation can be checked by operating the relevant function (On/Off).
ID REGIST WARNING The ID regist warning chime operation can be checked by operating the relevant function (On/Off).
I
LIGHT WARN ALM The light warning chime operation can be checked by operating the relevant function (On/Off).
WCS

POWER SUPPLY AND GROUND CIRCUIT
< COMPONENT DIAGNOSIS >
COMPONENT DIAGNOSIS
COMBINATION METER
COMBINATION METER : Diagnosis Procedure INFOID:0000000003470010
1.CHECK FUSE
Check for blown fuses.
Power source Fuse No.

Battery 11
Ignition switch ON or START 4
Is the inspection result normal?
YES >> GO TO 2.
NO >> Be sure to eliminate cause of malfunction before installing new fuse.
2.CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector terminals and ground.
Terminals
(+) (-) Ignition switch po- Voltage
Combination meter sition (Approx.)
Connector Terminal
Ground
1 OFF
M34 Battery voltage
2 ON
YES >> GO TO 3.
NO >> Check harness between combination meter and fuse.
3.CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect combination meter connector.
3. Check continuity between combination meter harness connector terminals and ground.
Terminals
(+) (-)
Continuity
Combination meter
Connector Terminal
Ground
3
M34 Existed
23
NO >> Repair harness or connector.
BCM (BODY CONTROL MODULE)
BCM (BODY CONTROL MODULE) : Diagnosis Procedure INFOID:0000000003470011
1.CHECK FUSE AND FUSIBLE LINK

Check that the following fuse and fusible link are not blown.

Signal name Fuse and fusible link No. A

M
Battery power supply
10
B
Is the fuse fusing?
YES >> Replace the blown fuse or fusible link after repairing the affected circuit if a fuse or fusible link is
blown. C
NO >> GO TO 2.
2.CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF. D
2. Disconnect BCM connectors.
3. Check voltage between BCM harness connector and ground.
E
Terminals
(+) (−) Voltage
BCM (Approx.) F
Connector Terminal
Ground
M118 1 G
Battery voltage
M119 11
Is the measurement value normal?
YES >> GO TO 3. H
3.CHECK GROUND CIRCUIT I
Check continuity between BCM harness connector and ground.
BCM J
Continuity
Connector Terminal Ground
M119 13 Existed
K
Does continuity exist?
L
WCS

METER BUZZER CIRCUIT
METER BUZZER CIRCUIT
Description INFOID:0000000003452040
• The buzzer for warning chime system is installed in the combination meter.
• The combination meter sounds the alarm buzzer based on the signals transmitted from various units.
Component Function Check INFOID:0000000003452041
1.CHECK OPERATION OF METER BUZZER

1. Select “BUZZER” of “BCM” on CONSULT-III.
2. Perform “LIGHT WARN ALM” of “Active Test”.
Does meter buzzer beep?
NO >> GO TO 2.
2.CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “BUZZER” monitor value.
BUZZER
Under the condition of buzzer input : On
Except above : Off
YES >> Replace combination meter.
NO >> Replace BCM. Refer to BCS-96, "Removal and Installation".
Diagnosis Procedure INFOID:0000000003452042
1.CHECK POWER SUPPLY OF COMBINATION METER

Check power supply of combination meter. Refer to MWI-43, "COMBINATION METER : Diagnosis Proce-
dure".
NO >> Repair power supply circuit of combination meter. Refer to WCS-22, "COMBINATION METER :
Diagnosis Procedure".

SEAT BELT BUCKLE SWITCH SIGNAL CIRCUIT
A
Transmits a seat belt buckle switch signal (driver side) to the combination meter. B
Component Function Check INFOID:0000000003452044
1.CHECK COMBINATION METER INPUT SIGNAL C

Select the “Data Monitor” for the “METER/M&A” and check the “BUCKLE SW” monitor value.
BUCKLE SW D
When seat belt is fastened : Off
When seat belt is unfastened : On
E
>> INSPECTION END

Diagnosis Procedure INFOID:0000000003452045 F

1. Turn ignition switch ON. G
2. Check voltage between combination meter harness connector terminal and ground.
Terminals H
(+) (-) Voltage
Condition
Combination meter (Approx.)
I
Connector Terminal
Ground
When seat belt is fastened 12 V
M34 35
When seat belt is unfastened 0V J
YES >> Replace combination meter
NO >> GO TO 2. K
2.CHECK SEAT BELT BUCKLE SWITCH CIRCUIT

1. Turn ignition switch OFF. L
2. Disconnect combination meter connector and seat belt buckle switch (driver side) connector.
3. Check continuity between combination meter harness connector terminal and seat belt buckle switch
(driver side) harness connector terminal.
M
Terminals
(+) (-) WCS
Continuity
Combination meter Seat belt buckle switch(driver side)
Connector Terminal Connector Terminal
*1 O
B409 15*1
M34 35 Exist
B449*2 40*2
• *1 : Without automatic drive positioner P
• *2 : With automatic drive positioner
4. Check harness continuity between combination meter harness connector terminal and ground.

Terminals
(+) (-)
Continuity
Combination meter
Connector Terminal Ground
M34 35 Not existed
YES >> GO TO 3.
3.CHECK SEAT BELT BUCKLE SWITCH GROUND CIRCUIT
Check harness continuity between seat belt buckle switch (driver side) harness connector terminal and
ground.
Terminals
(+) (-)
Continuity
Combination meter
Connector Terminal
Ground
B409*1 16*1
Exist
B449*2 41*2
• *1 : Without automatic drive positioner
• *2 : With automatic drive positioner
Component Inspection INFOID:0000000003452046
1.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)

1. Turn ignition switch OFF.
2. Disconnect the seat belt buckle switch (driver side) connector.
3. Check continuity between terminals.
Terminals
(+) (-)
Condition Continuity
Seat belt buckle switch (driver side)
Connector Terminal Connector Terminal
B409*1 15*1 B409*1 16*1

When seat belt is fastened Not existed
B449*2 40*2 B449*2 41*2
B409*1 15*1 B409*1 16*1

When seat belt is unfastened Exist
B449*2 40*2 B449*2 41*2
• Without automatic drive positioner
• With automatic drive positioner
NO >> Replace the seat belt buckle. Refer to SB-7, "SEAT BELT BUCKLE : Removal and Installation".

A
Wiring Diagram - WARNING CHIME - INFOID:0000000003452047
WCS
P
JCNWM1828GB

JCNWM1829GB

WCS
JCNWM1830GB

JCNWM1831GB

WCS
JCNWM1832GB

COMBINATION METER
< ECU DIAGNOSIS >
ECU DIAGNOSIS
COMBINATION METER
Reference Value INFOID:0000000003519120
VALUES ON THE DIAGNOSIS TOOL
Monitor Item Condition Value/Status

Equivalent to speedometer reading
SPEED METER Ignition switch NOTE:
While driving
[km/h] ON 655.35 is displayed when the malfunc-
tion signal is received
Equivalent to speedometer reading
SPEED OUTPUT Ignition switch NOTE:
While driving
[km/h] ON 655.35 is displayed when the malfunc-
tion signal is received
ODO OUTPUT Ignition switch Equivalent to odometer reading in
—
[km/h or mph] ON combination meter
Equivalent to tachometer reading
TACHO METER Ignition switch NOTE:
While driving
[rpm] ON 8191.875 is displayed when the mal-
function signal is received
FUEL METER Ignition switch
— Values according to fuel level
[L] ON
Values according to engine coolant
temperature
W TEMP METER Ignition switch
— NOTE:
[°C] ON
215 is displayed when the malfunction
signal is input
Ignition switch ABS warning lamp ON On

ABS W/L
ON ABS warning lamp OFF Off
Ignition switch VDC OFF indicator lamp ON On

VDC/TCS IND
ON VDC OFF indicator lamp OFF Off
Ignition switch SLIP Indicator lamp ON On

SLIP IND
ON SLIP indicator lamp OFF Off
Ignition switch Brake warning lamp ON On

BRAKE W/L
ON Brake warning lamp OFF Off
Ignition switch Door warning lamp ON On

DOOR W/L
ON Door warning lamp OFF Off
Ignition switch High-beam indicator lamp ON On

HI-BEAM IND
ON High-beam indicator lamp OFF Off
Ignition switch Turn signal indicator lamp ON On

TURN IND
ON Turn signal indicator lamp OFF Off
Ignition switch Light indicator lamp ON On

LIGHT IND
ON Light indicator lamp OFF Off
Ignition switch Oil pressure warning lamp ON On

OIL W/L
ON Oil pressure warning lamp OFF Off
Ignition switch Malfunction indicator lamp ON On

MIL
ON Malfunction indicator lamp OFF Off
Ignition switch CRUISE indicator lamp ON On

CRUISE IND
ON CRUISE indicator lamp OFF Off

COMBINATION METER
< ECU DIAGNOSIS >
A
Ignition switch O/D OFF indicator lamp ON On
O/D OFF IND
ON O/D OFF indicator lamp OFF Off
Ignition switch AWD warning lamp ON On B

4WD W/L
ON AWD warning lamp OFF Off
Ignition switch AWD LOCK indicator lamp ON On

4WD LOCK IND
ON AWD LOCK indicator lamp OFF Off C
Ignition switch Low-fuel warning lamp ON On

FUEL W/L
ON Low-fuel warning lamp OFF Off
D
Ignition switch Washer warning displayed On
WASHER W/L
ON Washer warning not displayed Off
Ignition switch Low tire pressure lamp ON On E

AIR PRES W/L
ON Low tire pressure lamp OFF Off
Ignition switch Key warning lamp (green/yellow) ON On

KEY G/Y W/L F
ON Key warning lamp (green/yellow) OFF Off
Ignition switch
Engine start information display B&P I
ON
G
Ignition switch
Engine start information display B&P N
ACC
Ignition switch H
Key ID warning display ID NG
LOCK
Ignition switch
Steering lock information display ROTAT
LOCK
I
Ignition switch
P position warning display SFT P
LOCK
LCD
Ignition switch
Intelligent Key insert information display INSRT J
LOCK
Ignition switch
Intelligent Key low battery warning display BATT
LOCK
K
Ignition switch
Take away warning display NO KY
ON
Ignition switch
LOCK
Key warning display OUTKY L
Ignition switch
ACC warning display LK WN
ON
M
Shift position indicator P display P
Shift position indicator R display R
Ignition switch
SHIFT IND Shift position indicator N display N WCS
ON
Shift position indicator D display D
Shift position indicator L display L
Overdrive control switch ON On O
Ignition switch
O/D OFF SW
ON Overdrive control switch OFF Off
NOTE:
M RANGE SW
Ignition switch
This item is displayed, but cannot be moni- Off
P
ON
tored.
NOTE:
Ignition switch
NM RANGE SW This item is displayed, but cannot be moni- Off
ON
tored.

COMBINATION METER
< ECU DIAGNOSIS >
NOTE:
Ignition switch
AT SFT UP SW This item is displayed, but cannot be moni- Off
ON
tored.
NOTE:
Ignition switch
AT SFT DWN SW This item is displayed, but cannot be moni- Off
ON
tored.
NOTE:
Ignition switch
ST SFT UP SW This item is displayed, but cannot be moni- Off
ON
tored.
NOTE:
Ignition switch
ST SFT DWN SW This item is displayed, but cannot be moni- Off
ON
tored.
Ignition switch Parking brake switch ON On

PKB SW
ON Parking brake switch OFF Off
Ignition switch Seat belt (driver side) not fastened On

BUCKLE SW
ON Seat belt (driver side) fastened Off
Ignition switch Brake fluid level switch ON On

BRAKE OIL SW
ON Brake fluid level switch OFF Off
DISTANCE Ignition switch Possible driving distance calculated by
—
[km] ON combination meter
Ignition switch Other than the following On

A/C AMP CONN
ON Receives ambient sensor power signal Off
Ignition switch When is pressed On

ENTER SW
ON
Other than the above Off
Ignition switch When is pressed On

SELECT SW
ON Other than the above Off
Equivalent to ambient temperature
OUTSIDE TEMP Ignition switch NOTE:
—
[°C] or [°F] ON This may not match the indicated value
on the information display.
Ignition switch Low fuel warning displayed On

FUEL LOW SIG
ON Low fuel warning not displayed Off
Ignition switch Buzzer ON On

BUZZER
ON Buzzer OFF Off
NOTE:
Some items are not available according to vehicle specification.
TERMINAL LAYOUT
JPNIA0968GB
PHYSICAL VALUES

COMBINATION METER
< ECU DIAGNOSIS >
Terminal No. A
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
B
Ignition
1
Ground Battery power supply Input switch — Battery voltage
(Y)
OFF
C
Ignition
2
Ground IGN signal Input switch — Battery voltage
(O)
ON
Ignition D
3
Ground Ground — switch — 0V
(B)
ON
E
• Lighting switch 1ST

• When meter illumination F
is maximum
Ignition G
5 JPNIA0828GB
Ground Illumination control signal Output switch
(SB)
ON
H
• Lighting switch 1ST
• When meter illumination
is minimum
I
JPNIA0827GB
Ignition When trip reset switch is

8 10 0V J
Trip reset signal Input switch pressed.
(SB) (O)
ON Other than the above 5V
Ignition
10 K
Ground Meter control switch ground — switch — 0V
(O)
ON
Ignition 0V
11 10 When is pressed.
Enter switch signal Input switch L
(L) (O)
Ignition When is pressed. 0V
12 10
Select switch signal Input switch M
(R) (O) Other than the above 5V
ON
13 Ignition 0V
10 Illumination control switch When is pressed.
(Y*1 or Input switch WCS
(O) signal (+)
V*2) ON Other than the above 5V
Ignition 0V
14 10 Illumination control switch When is pressed.
Input switch
(GR) (O) signal (-) O
Air bag warning lamp
Ignition 4V
15 ON
(BR)
Ground Air bag signal Input switch P
ON Air bag warning lamp
0V
OFF

COMBINATION METER
< ECU DIAGNOSIS >
Terminal No.
Description
(Wire color) Value
Condition
Input/ (Approx.)
+ – Signal name
Output
Ignition
18 Changes depending to am-
Ground Ambient sensor signal Input switch
(L) bient temperature.
ON
JSNIA0014GB
Ignition
19
Ground Ambient sensor power Input switch — 5V
(P)
ON
Ignition
20
Ground Ambient sensor ground Input switch — 0V
(Y)
ON
21
— CAN-H — — — —
(L)
22
— CAN-L — — — —
(P)
Ignition
23
Ground Ground — switch — 0V
(B)
ON
Ignition
24 Fuel level sensor signal
Ground — switch — 0V
(W) ground
ON
Ignition Charge warning lamp ON 2V
25
Ground Alternator signal Input switch
(BR) Charge warning lamp OFF 12 V
ON
Ignition Parking brake ON 0V
26
Ground Parking brake switch signal Input switch
(G) Parking brake OFF 5V
ON
Ignition Brake fluid level is normal 12 V

27 Brake fluid level switch sig-
Ground Input switch Brake fluid level is less than
(V) nal 0V
ON LOW level
Ignition Washer level switch ON 0V
29
Ground Washer level switch signal Input switch
(R) Washer level switch OFF 5V
ON
NOTE:
The maximum voltage varies de-
pending on the specification
(destination unit).
Ignition Speedometer operated
30 Vehicle speed signal output
Ground Output switch [When vehicle speed is ap-
(P) (2-pulse)
ON prox. 40 km/h (25 MPH)]
JSNIA0015GB

COMBINATION METER
< ECU DIAGNOSIS >
Terminal No.
Description
(Wire color) Value A
Condition
Input/ (Approx.)
+ – Signal name
Output
NOTE: B
The maximum voltage varies de-
pending on the specification
(destination unit).
C
Ignition Speedometer operated
31 Vehicle speed signal output
Ground Output switch [When vehicle speed is ap-
(V) (8-pulse)
ON prox. 40 km/h (25 MPH)]
D
JSNIA0012GB
E
Overdrive control switch
Ignition 0V
32 Overdrive control switch pressed.
Ground Input switch
(LG) signal Overdrive control switch
ON 12 V F
not pressed.
G
Ignition
34
Ground Fuel level sensor signal Input switch —
(G)
ON
H
JPNIA0740ZZ
When driver seat belt is fas- I

Ignition 12 V
35 Seat belt buckle switch sig- tened.
Ground Input switch
(SB) nal (driver side) When driver seat belt is un-
ON 0V
fastened.
J
• When getting in the pas-
senger seat.
12 V
• When passenger seat
Ignition belt is fastened. K
36 Seat belt buckle switch sig-
Ground Input switch
(R) nal (passenger side) • When getting in the pas-
ON
senger seat.
0V
• When passenger seat L
belt is unfastened.
*1: Without automatic drive positioner
*2: With automatic drive positioner M
Wiring Diagram - METER - INFOID:0000000003470024
NOTE: WCS
• Type A Up to VIN: JN8AZ18U*9W100000, JN8AZ18W*9W200000 (EXCEPT FOR MEXICO),
JN8AZ18U*9W710000, JN8AZ18W*9W810000 (FOR MEXICO)
O

COMBINATION METER
< ECU DIAGNOSIS >
• Type B: From VIN: JN8AZ18U*9W100001, JN8AZ18W*9W200001 (EXCEPT FOR MEXICO),
JCNWM1816GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWM1817GB

COMBINATION METER
< ECU DIAGNOSIS >
JCNWM1818GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWM1819GB

COMBINATION METER
< ECU DIAGNOSIS >
JCNWM1820GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWM1821GB

COMBINATION METER
< ECU DIAGNOSIS >
JCNWM1822GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWM1823GB

COMBINATION METER
< ECU DIAGNOSIS >
JCNWM1824GB

COMBINATION METER
< ECU DIAGNOSIS >
WCS
JCNWM1825GB
P
Fail-Safe INFOID:0000000003470025
FAIL-SAFE
The combination meter activates the fail-safe control if CAN communication with each unit is malfunctioning.

COMBINATION METER
< ECU DIAGNOSIS >
Function Specifications
Speedometer
Tachometer Reset to zero by suspending communication.
Engine coolant temperature gauge
When suspending communication, changes to nighttime
Illumination control
mode.
Door open warning
The display turns off by suspending communication.
Parking brake release warning
Instantaneous fuel warning • When reception time of an abnormal signal is 2 seconds or
Information display less, the last received datum is used for calculation to indi-
Average fuel consumption
cate the result.
Average vehicle speed • When reception time of an abnormal signal is more than two
seconds, the last result calculated during normal condition
Travel distance is indicated.
Buzzer The buzzer turns off by suspending communication.
ABS warning lamp
VDC OFF indicator lamp
SLIP indicator lamp The lamp turns on by suspending communication.
Brake warning lamp
AWD warning lamp
Low tire pressure warning lamp The lamp turns ON after flashing for 1 minute.
High beam indicator lamp
Warning lamp/indicator
Turn signal indicator lamp
lamp
Light indicator lamp
Oil pressure warning lamp
Malfunction indicator lamp The lamp turns off by suspending communication.
CRUISE indicator lamp
O/D OFF indicator lamp
AWD LOCK indicator lamp
Key warning lamp
DTC Index INFOID:0000000003470026
Display contents of CONSULT-III Diagnostic item is detected when ... Refer to

MWI-38,
CAN COMM CIRCUIT When combination meter is not transmitting or receiving CAN communication signal
"Diagnosis
[U1000] for 2 seconds or more.
Procedure"
MWI-39,
CONTROL UNIT (CAN) When detecting error during the initial diagnosis of the CAN controller of combina-
"Diagnosis
[U1010] tion meter.
Procedure"
MWI-40,
VEHICLE SPEED The abnormal vehicle speed signal is input from the ABS actuator and electric unit
"Diagnosis
[B2205] (control unit) for 2 seconds or more.
Procedure"
MWI-41,
ENGINE SPEED If ECM continuously transmits abnormal engine speed signals for 2 seconds or
"Diagnosis
[B2267] more.
Procedure"
MWI-42,
WATER TEMP If ECM continuously transmits abnormal engine coolant temperature signals for 60
"Diagnosis
[B2268] seconds or more.
Procedure"

< ECU DIAGNOSIS >
A
Reference Value INFOID:0000000003470027
VALUES ON THE DIAGNOSIS TOOL B

CONSULT-III MONITOR ITEM
C
Other than front wiper switch HI Off
FR WIPER HI
Front wiper switch HI On
Other than front wiper switch LO Off D
FR WIPER LOW
Front wiper switch LO On
Front washer switch OFF Off
FR WASHER SW E
Front washer switch ON On
Other than front wiper switch INT/AUTO Off
FR WIPER INT
Front wiper switch INT/AUTO On
F
Front wiper is not in STOP position Off
FR WIPER STOP
Front wiper is in STOP position On
INT VOLUME Wiper intermittent dial is in a dial position 1 - 7 Wiper intermittent dial position G
Other than rear wiper switch ON Off
RR WIPER ON
Rear wiper switch ON On
H
Other than rear wiper switch INT Off
RR WIPER INT
Rear wiper switch INT On
Rear washer switch OFF Off I
RR WASHER SW
Rear washer switch ON On
Rear wiper is in STOP position Off
RR WIPER STOP J
Rear wiper is not in STOP position On
Other than turn signal switch RH Off
TURN SIGNAL R
Turn signal switch RH On K
Other than turn signal switch LH Off
TURN SIGNAL L
Turn signal switch LH On
Other than lighting switch 1ST and 2ND Off
L
TAIL LAMP SW
Lighting switch 1ST or 2ND On
Other than lighting switch HI Off
HI BEAM SW M
Lighting switch HI On
Other than lighting switch 2ND Off
HEAD LAMP SW 1
Lighting switch 2ND On WCS
Other than lighting switch 2ND Off
HEAD LAMP SW 2
Lighting switch 2ND On
O
Other than lighting switch PASS Off
PASSING SW
Lighting switch PASS On
Other than lighting switch AUTO Off P
AUTO LIGHT SW
Lighting switch AUTO On
Front fog lamp switch OFF Off
FR FOG SW
Front fog lamp switch ON On
NOTE:
RR FOG SW Off
The item is indicated, but not monitored.

< ECU DIAGNOSIS >
Driver door closed Off
DOOR SW-DR
Driver door opened On
Passenger door closed Off
DOOR SW-AS
Passenger door opened On
Rear RH door closed Off
DOOR SW-RR
Rear RH door opened On
Rear LH door closed Off
DOOR SW-RL
Rear LH door opened On
Back door closed Off
DOOR SW-BK
Back door opened On
Other than power door lock switch LOCK Off
CDL LOCK SW
Power door lock switch LOCK On
Other than power door lock switch UNLOCK Off
CDL UNLOCK SW
Power door lock switch UNLOCK On
Other than driver door key cylinder LOCK position Off
KEY CYL LK-SW
Driver door key cylinder LOCK position On
Other than driver door key cylinder UNLOCK position Off
KEY CYL UN-SW
Driver door key cylinder UNLOCK position On
NOTE:
KEY CYL SW-TR Off
Hazard switch is OFF Off
HAZARD SW
Hazard switch is ON On
REAR DEF SW Rear window defogger switch OFF Off
NOTE:
At model with BOSE au-
dio system this item is not Rear window defogger switch ON On
monitored.
NOTE:
TR CANCEL SW Off
Back door opener switch OFF Off
TR/BD OPEN SW
While the back door opener switch is turned ON On
NOTE:
TRNK/HAT MNTR Off
LOCK button of the key is not pressed Off
RKE-LOCK
LOCK button of the key is pressed On
UNLOCK button of the key is not pressed Off
RKE-UNLOCK
UNLOCK button of the key is pressed On
BACK DOOR OPEN button of the key is not pressed Off
RKE-TR/BD
BACK DOOR OPEN button of the key is pressed On
PANIC button of the key is not pressed Off
RKE-PANIC
PANIC button of the key is pressed On
UNLOCK button of the key is not pressed Off
RKE-P/W OPEN
UNLOCK button of the key is pressed and held On
LOCK/UNLOCK button of the key is not pressed and held simulta-
Off
neously
RKE-MODE CHG
LOCK/UNLOCK button of the key is pressed and held simulta-
On
neously

< ECU DIAGNOSIS >
A
Bright outside of the vehicle Close to 5 V
OPTICAL SENSOR
Dark outside of the vehicle Close to 0 V
Driver door request switch is not pressed Off B
REQ SW -DR
Driver door request switch is pressed On
Passenger door request switch is not pressed Off
REQ SW -AS
Passenger door request switch is pressed On C
NOTE:
REQ SW -RR Off
D
NOTE:
REQ SW -RR Off
Back door request switch is not pressed Off
REQ SW -BD/TR E
Back door request switch is pressed On
Push-button ignition switch (push switch) is not pressed Off
PUSH SW
Push-button ignition switch (push switch) is pressed On F
Ignition switch in OFF or ACC position Off
IGN RLY2 -F/B
Ignition switch in ON position On
NOTE:
G
ACC RLY -F/B Off
NOTE:
CLUCH SW Off H
The brake pedal is depressed when No. 7 fuse is blown Off
BRAKE SW 1 The brake pedal is not depressed when No. 7 fuse is blown, or No.
On I
7 fuse is normal
The brake pedal is not depressed Off
BRAKE SW 2
Stop lamp switch 1 signal circuit is normal On
J
Selector lever in P position Off
DETE/CANCL SW
Selector lever in any position other than P On
Selector lever in any position other than P and N Off K
SFT PN/N SW
Selector lever in P or N position On
Steering is unlocked Off
S/L -LOCK L
Steering is locked On
Steering is locked Off
S/L -UNLOCK
Steering is unlocked On M
S/L RELAY-F/B
WCS
Driver door is unlocked Off
UNLK SEN -DR
Driver door is locked On
Push-button ignition switch (push-switch) is not pressed Off O
PUSH SW -IPDM
Push-button ignition switch (push-switch) is pressed On
IGN RLY1 -F/B P
Selector lever in any position other than P Off
DETE SW -IPDM
Selector lever in P position On
Selector lever in any position other than P and N Off
SFT PN -IPDM
Selector lever in P or N position On

< ECU DIAGNOSIS >
Selector lever in any position other than P Off
SFT P -MET
Selector lever in P position On
Selector lever in any position other than N Off
SFT N -MET
Selector lever in N position On
Engine stopped Stop
While the engine stalls Stall
ENGINE STATE
At engine cranking Crank
Engine running Run
Steering is unlocked Off
S/L LOCK-IPDM
Steering is locked On
Steering is locked Off
S/L UNLK-IPDM
Steering is unlocked On
Steering lock system is not the LOCK condition and the changing
Off
condition from LOCK to UNLOCK.
S/L RELAY-REQ
Steering lock system is the LOCK condition or the changing condi-
On
tion from LOCK to UNLOCK.
VEH SPEED 1 While driving Equivalent to speedometer reading
VEH SPEED 2 While driving Equivalent to speedometer reading
Driver door is locked LOCK
DOOR STAT-DR Wait with selective UNLOCK operation (5 seconds) READY
Driver door is unlocked UNLOCK
Passenger door is locked LOCK
DOOR STAT-AS Wait with selective UNLOCK operation (5 seconds) READY
Passenger door is unlocked UNLOCK
Steering is locked Reset
ID OK FLAG
Steering is unlocked Set
The engine start is prohibited Reset
PRMT ENG STRT
The engine start is permitted Set
NOTE:
PRMT RKE STRT Reset
The key is not inserted into key slot Off
KEY SW -SLOT
The key is inserted into key slot On
RKE OPE COUN1 During the operation of the key Operation frequency of the key
NOTE:
RKE OPE COUN2 —
The key ID that the key slot receives is not recognized by any key
Yet
ID registered to BCM.
CONFRM ID ALL
The key ID that the key slot receives is recognized by any key ID
Done
registered to BCM.
The key ID that the key slot receives is not recognized by the fourth
Yet
key ID registered to BCM.
CONFIRM ID4
The key ID that the key slot receives is recognized by the fourth key
Done
The key ID that the key slot receives is not recognized by the third
Yet
CONFIRM ID3
The key ID that the key slot receives is recognized by the third key
Done

< ECU DIAGNOSIS >
A
The key ID that the key slot receives is not recognized by the sec-
Yet
ond key ID registered to BCM.
CONFIRM ID2
The key ID that the key slot receives is recognized by the second
Done B
The key ID that the key slot receives is not recognized by the first
Yet
CONFIRM ID1 C
The key ID that the key slot receives is recognized by the first key
Done
The ID of fourth key is not registered to BCM Yet
TP 4 D
The ID of fourth key is registered to BCM Done
The ID of third key is not registered to BCM Yet
TP 3
The ID of third key is registered to BCM Done E
The ID of second key is not registered to BCM Yet
TP 2
The ID of second key is registered to BCM Done
The ID of first key is not registered to BCM Yet F
TP 1
The ID of first key is registered to BCM Done
Ignition switch ON (Only when the signal from the transmitter is re-
AIR PRESS FL Air pressure of front LH tire G
ceived)
AIR PRESS FR Air pressure of front RH tire
ceived)
H
AIR PRESS RR Air pressure of rear RH tire
ceived)
AIR PRESS RL Air pressure of rear LH tire I
ceived)
ID of front LH tire transmitter is registered Done
ID REGST FL1
ID of front LH tire transmitter is not registered Yet
J
ID of front RH tire transmitter is registered Done
ID REGST FR1
ID of front RH tire transmitter is not registered Yet
ID of rear RH tire transmitter is registered Done K
ID REGST RR1
ID of rear RH tire transmitter is not registered Yet
ID of rear LH tire transmitter is registered Done
ID REGST RL1 L
ID of rear LH tire transmitter is not registered Yet
Tire pressure indicator OFF Off
WARNING LAMP
Tire pressure indicator ON On M
Tire pressure warning alarm is not sounding Off
BUZZER
Tire pressure warning alarm is sounding On
WCS

< ECU DIAGNOSIS >
TERMINAL LAYOUT
JPMIA0062ZZ
PHYSICAL VALUES

< ECU DIAGNOSIS >
Terminal No. Description A

(Wire color) Value
Input/ Condition
Signal name (Approx.)
+ – Output
1 B
Ground Battery power supply Input Ignition switch OFF Battery voltage
(W)
2 P/W power supply
Ground Output Ignition switch OFF Battery voltage
(GR) (BAT) C
3 P/W power supply
Ground Output Ignition switch ON Battery voltage
(L) (RAP)
Interior room lamp battery saver is activated. D
0V
(Cuts the interior room lamp power supply)
4 Interior room lamp
Ground Output Interior room lamp battery saver is not activat-
(P) power supply
ed. Battery voltage
E
(Outputs the interior room lamp power supply)
UNLOCK (Actuator is acti-
Battery voltage
5 Passenger door UN- vated)
(G)
Ground
LOCK
Output Passenger door F
Other than UNLOCK (Actu-
0V
ator is not activated)
7 ON 0V
Ground Step lamp Output Step lamp G
(W) OFF Battery voltage
LOCK (Actuator is activat-
Battery voltage
8 ed)
Ground All doors LOCK Output All doors H
(V) Other than LOCK (Actuator
0V
is not activated)
UNLOCK (Actuator is acti- I
Battery voltage
9 vated)
Ground Driver door UNLOCK Output Driver door
(G) Other than UNLOCK (Actu-
0V
J
UNLOCK (Actuator is acti-
Rear RH door and Battery voltage
10 Rear RH door vated)
Ground rear LH door UN- Output
(P) and rear LH door Other than UNLOCK (Actu-
LOCK 0V K
11
Ground Battery power supply Input Ignition switch OFF Battery voltage
(LG)
L
13
Ground Ground — Ignition switch ON 0V
(B)
OFF 0V
M
NOTE:
When the illumination brighten-
ing/dimming level is in the neutral
position WCS
Push-button ignition
14
Ground switch illumination Output Tail lamp
(O) ON
ground
O
JSNIA0010GB P
OFF Battery voltage
15
Ground ACC indicator lamp Output Ignition switch ACC 0.2 V
(L)
ON 0V

< ECU DIAGNOSIS >
Terminal No. Description
(Wire color) Value
Input/ Condition
+ – Output
Turn signal switch OFF 0V
17 Ignition switch
Ground Turn signal RH Output
(G) ON Turn signal switch RH
PKID0926E
6.5 V
Turn signal switch OFF 0V
18 Ignition switch
Ground Turn signal LH Output
(BR) ON Turn signal switch LH
PKID0926E
6.5 V
19 Room lamp timer Interior room OFF Battery voltage

Ground Output
(Y) control lamp ON 0V
OPEN (Back door opener
Battery voltage
actuator is activated)
23
Ground Back door open Output Back door Other than OPEN (Back
(BR)
door opener actuator is not 0V
activated)
26 OFF (Stopped) 0V
Ground Rear wiper Output Rear wiper
(G) ON (Operated) Battery voltage
When Intelligent Key is in

the passenger compart-
ment
JMKIA0062GB
34*1 Ground
Luggage room anten-
Output
Ignition switch
(B) na (-) OFF
When Intelligent Key is not

in the passenger compart-
ment
JMKIA0063GB

< ECU DIAGNOSIS >
Input/ Condition
+ – Output

the passenger compart- C
ment
JMKIA0062GB
1 Luggage room anten- Ignition switch

D
35* Ground Output
(W) na (+) OFF
E
ment
F
JMKIA0063GB

H
the antenna detection area
JMKIA0062GB
I
When the back
38*1 Ground
Rear bumper anten-
Output
door request
(L) na (-) switch is operat-
ed with ignition J
switch OFF
in the antenna detection
K
area
JMKIA0063GB
L
M
WCS
JMKIA0062GB
When the back
39*1 Ground
Rear bumper anten-
Output
door request
(BR) na (+) switch is operat- O
ed with ignition
switch OFF
When Intelligent Key is not P
area
JMKIA0063GB
47 Ignition relay (IPDM OFF or ACC Battery voltage

Ground Output Ignition switch
(L) E/R) control ON 0V

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
When selector lever is in P
Battery voltage
Ignition switch or N position
52 ON
Ground Starter relay control Output When selector lever is not
(R) 0.3 V
in P or N position
Ignition switch OFF 0V
ON (Pressed) 0V
61*1 Ground
Back door request
Input
Back door re-
(R) switch quest switch OFF (Not pressed)
JPMIA0016GB
1.0 V
64*1 Sounding 0V
Ground Warning buzzer Output Warning buzzer
(GR) Not sounding Battery voltage
65 Rear wiper stop posi- In stop position

Ground Input Rear wiper
(O) tion
JPMIA0016GB
1.0 V
Not in stop position 0V
OFF (When back door

66 closes)
Ground Back door switch Input Back door switch
(Y)
JPMIA0011GB
11.8 V
ON (When back door
0V
opens)
Pressed 0V
67 Back door opener Back door opener

Ground Input
(LG) switch switch Not pressed
JPMIA0011GB
11.8 V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
OFF (When rear RH door

68 Rear RH door closes) C
Ground Rear RH door switch Input
(W) switch
JPMIA0011GB
11.8 V D
ON (When rear RH door
0V
opens)
E
OFF (When rear LH door F

69 Rear LH door closes)
Ground Rear LH door switch Input
(R) switch
JPMIA0011GB
G
11.8 V
ON (When rear LH door
0V H
opens)
I
ment
J
JMKIA0062GB
72*1 Ground
Room antenna 2 (-)
Output
Ignition switch
(B) (Center console) OFF K
When Intelligent Key is not L

ment
JMKIA0063GB
M
WCS

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output

ment
JMKIA0062GB
1 Room antenna 2 (+) Ignition switch

73* Ground Output
(W) (Center console) OFF

ment
JMKIA0063GB

JMKIA0062GB
When the pas-
74*1 Ground
Passenger door an-
Output
senger door re-
(Y) tenna (-) quest switch is
operated with ig-
nition switch OFF
area
JMKIA0063GB

JMKIA0062GB
When the pas-
75*1 Ground
Passenger door an-
Output
senger door re-
(LG) tenna (+) quest switch is
operated with ig-
nition switch OFF
area
JMKIA0063GB

< ECU DIAGNOSIS >
Input/ Condition
+ – Output

the antenna detection area C
When the driver JMKIA0062GB
1 Driver door antenna door request

D
76* Ground Output
(V) (-) switch is operat-
ed with ignition
switch OFF E
area
F
JMKIA0063GB

H
JMKIA0062GB
I
When the driver
77*1 Ground
Driver door antenna
Output
door request
(P) (+) switch is operat-
ed with ignition J
switch OFF
K
area
JMKIA0063GB
L
M
ment
WCS
JMKIA0062GB
78*1 Ground
Room antenna 1 (-)
Output
Ignition switch
(R) (Instrument panel) OFF O
When Intelligent Key is not P

ment
JMKIA0063GB

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output

ment
JMKIA0062GB
1 Room antenna 1 (+) Ignition switch

79* Ground Output
(G) (Instrument panel) OFF

ment
JMKIA0063GB
Ignition switch is pressed Just after pressing ignition

80 NATS antenna amp Input/
Ground During waiting while inserting the key into switch. Pointer of tester should
(SB) (built in key slot) Output
the key slot. move.
Ignition switch is pressed Just after pressing ignition
81 NATS antenna amp Input/
Ground During waiting while inserting the key into switch. Pointer of tester should
(O) (built in key slot) Output
the key slot. move.
82 Ignition relay [fuse OFF or ACC 0V

(BR) block (J/B)] control ON Battery voltage
During waiting
JMKIA0064GB
Remote keyless entry
83 Input/
Ground receiver communica-
(P) Output
tion
When operating either button on the key
JMKIA0065GB

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
All switches OFF

(Wiper intermittent dial 4) C
JPMIA0041GB
1.4 V D
E
Front fog lamp switch ON
(Wiper intermittent dial 4)
F
JPMIA0037GB
87 Combination switch Combination 1.3 V

Ground Input G
(R) INPUT 5 switch
Rear wiper switch ON

H
JPMIA0039GB
I
1.3 V
J
Any of the conditions below
with all switches OFF
• Wiper intermittent dial 1
• Wiper intermittent dial 2 K
JPMIA0040GB
1.3 V L
WCS

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
All switches OFF

JPMIA0041GB
1.4 V
Lighting switch HI
JPMIA0036GB
1.3 V
88 Combination switch Combination Lighting switch 2ND

Ground Input
(GR) INPUT 3 switch (Wiper intermittent dial 4)
JPMIA0037GB
1.3 V
Rear washer switch ON

JPMIA0039GB
1.3 V

JPMIA0040GB
1.3 V
Push-button igni- Pressed 0V
89 Push-button ignition
Ground Input tion switch (push
(BR) switch (push switch) Not pressed Battery voltage
switch)
90 Input/
Ground CAN - L — —
(P) Output
91 Input/
Ground CAN - H — —
(L) Output

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
OFF 0V
B
92 C
1 Key slot illumina-
(R)* Ground Key slot illumination Output Blinking
tion
(L)*2
D
JPMIA0015GB
6.5 V
ON Battery voltage
E
OFF or ACC Battery voltage
93
Ground ON indicator lamp Output Ignition switch ACC 0.2 V
(L)
ON 0V F
95 OFF 0V
Ground ACC relay control Output Ignition switch
(L) ACC or ON Battery voltage
G
Control device (de-
96
Ground tention switch) power Output — Battery voltage
(Y)
supply
LOCK status 0V H
97 Steering lock condi-
Ground Input Steering lock
(O) tion No. 1 UNLOCK status Battery voltage
98 Steering lock condi- LOCK status Battery voltage

Ground Input Steering lock I
(L) tion No. 2 UNLOCK status 0V
99 Selector lever P posi- P position 0V

Ground Input Selector lever
(V) tion switch Any position other than P Battery voltage J
ON (Pressed) 0V
100*1 Ground
Passenger door re-
Input
Passenger door
(P) quest switch request switch OFF (Not pressed) L
JPMIA0016GB
1.0 V M
ON (Pressed) 0V
WCS
101*1 Ground
Driver door request
Input
Driver door re-
(W) switch quest switch OFF (Not pressed) O
JPMIA0016GB
1.0 V
P
102 Blower fan motor re- OFF or ACC 0V

(Y) lay control ON Battery voltage
Remote keyless entry
103
Ground receiver power sup- Output Ignition switch OFF Battery voltage
(L)
ply

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
106 Steering lock unit OFF or ACC Battery voltage

(Y) power supply ON 0V
All switches OFF
JPMIA0041GB
1.4 V
Turn signal switch LH
JPMIA0037GB
1.3 V
Combination
107 Combination switch switch
Ground Input Turn signal switch RH
(O) INPUT 1 (Wiper intermit-
tent dial 4)
JPMIA0036GB
1.3 V
Front wiper switch LO
JPMIA0038GB
1.3 V
Front washer switch ON
JPMIA0039GB
1.3 V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
All switches OFF

(Wiper intermittent dial 4) C
JPMIA0041GB
1.4 V D
E
Lighting switch AUTO
F
JPMIA0038GB
1.3 V
G
108 Combination switch Combination Lighting switch 1ST

H
Ground Input
(P) INPUT 4 switch (Wiper intermittent dial 4)
JPMIA0036GB
I
1.3 V
Rear wiper switch INT

(Wiper intermittent dial 4) K
JPMIA0040GB
1.3 V L
Any of the conditions below M

• Wiper intermittent dial 6 WCS
JPMIA0039GB
1.3 V
O

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
All switches OFF
JPMIA0041GB
1.4 V
Lighting switch PASS
JPMIA0037GB
1.3 V
Combination
Ground Input Lighting switch 2ND
(SB) INPUT 2 (Wiper intermit-
tent dial 4)
JPMIA0036GB
1.3 V
Front wiper switch INT/

AUTO
JPMIA0038GB
1.3 V
Front wiper switch HI
JPMIA0040GB
1.3 V
ON 0V
110
Ground Hazard switch Input Hazard switch
(G) OFF
JPMIA0012GB
1.1 V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
LOCK status Battery voltage
B
C
LOCK or UNLOCK
111 Steering lock unit Input/
Ground Steering lock
(LG) communication Output D
JMKIA0066GB
For 15 seconds after UN-

LOCK
Battery voltage E
15 seconds or later after
0V
UNLOCK
F
G
112 Rain sensor serial Input/
Ground Ignition switch ON
(R) link Output
H
JPMIA0156GB
8.7 V
When bright outside of the
Close to 5 V I
113*3 Ignition switch vehicle
Ground Optical sensor Input
(O) ON When dark outside of the
Close to 0 V
vehicle
116
J
Ground Stop lamp switch 1 Input — Battery voltage
(GR)
OFF (Brake pedal is not
0V
118 depressed) K
Ground Stop lamp switch 2 Input Stop lamp switch
(L) ON (Brake pedal is de-
Battery voltage
pressed)
L
LOCK status (unlock sen- M

1 Front door lock as- sor switch OFF)
119* Ground sembly driver side Input Driver door
(W) (Unlock sensor)
JPMIA0012GB
WCS
1.1 V
UNLOCK status (unlock
0V
sensor switch ON) O
121 When the key is inserted into key slot Battery voltage
Ground Key slot switch Input
(Y) When the key is not inserted into key slot 0V
P
122 OFF 0V
Ground ACC feedback Input Ignition switch
(R) ACC or ON Battery voltage
123 OFF or ACC 0V

Ground IGN feedback Input Ignition switch
(G) ON Battery voltage

< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
OFF (When passenger

124 Passenger door Passenger door door closes)
Ground Input
(R) switch switch
JPMIA0011GB
11.8 V
ON (When passenger door
0V
opens)
Rear window defogger

130*4 Rear window defog- Ignition switch switch OFF
Ground Input
(BR) ger switch ON
JPMIA0012GB
1.1 V
Rear window defogger
0V
switch ON
132 Power window switch Input/ Ignition switch ON

Ground
(G) communication Output
JPMIA0013GB
10.2 V
Ignition switch OFF or ACC Battery voltage
ON (When tail lamps OFF) 9.5 V
NOTE:
The pulse width of this wave is
varied by the illumination bright-
ening/dimming level.
Push-button igni-
133 Push-button ignition
Ground Output tion switch illumi- ON (When tail lamps ON)
(W) switch illumination
nation
JPMIA0159GB
OFF 0V
137 Receiver and sensor
Ground Input Ignition switch ON 0V
(P) ground
138 Receiver and sensor OFF 0V

(V) power supply ACC or ON 5.0 V

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
Standby state C
OCC3881D
5 Tire pressure receiv- Input/ Ignition switch

D
139* Ground
(O) er communication Output ON
E
When receiving the signal
from the transmitter
F
OCC3880D
P or N position Battery voltage G

140 Selector lever P/N
Ground Input Selector lever
(GR) position Except P and N positions 0V
ON 0V
H
I
141
Ground Security indicator Output Security indicator Blinking
(O)
J
JPMIA0014GB
11.3 V
OFF Battery voltage K
All switches OFF 0V
Lighting switch 1ST
Lighting switch HI
L
Combination
142 Combination switch switch Lighting switch 2ND
Ground Output
(L) OUTPUT 5 (Wiper intermit-
tent dial 4) M
Turn signal switch RH
JPMIA0031GB
10.7 V WCS
All switches OFF
0V
Front wiper switch HI O
Rear wiper switch INT
143 Combination switch Combination (Wiper intermittent dial 4) P
Ground Output
(W) OUTPUT 1 switch Any of the conditions below
• Wiper intermittent dial 3 JPMIA0032GB
• Wiper intermittent dial 6 10.7 V


< ECU DIAGNOSIS >
(Wire color) Value
Input/ Condition
+ – Output
All switches OFF
0V
Front washer switch ON
Rear wiper switch ON
144 Combination switch Combination
Ground Output
(P) OUTPUT 2 switch Rear washer switch ON
JPMIA0033GB
10.7 V
All switches OFF 0V
Front wiper switch INT/
AUTO
Combination
Front wiper switch LO
Ground Output
(V) OUTPUT 3 (Wiper intermit-
tent dial 4)
Lighting switch AUTO
JPMIA0034GB
10.7 V
All switches OFF 0V
Front fog lamp switch ON
Lighting switch 2ND
Combination
146 Combination switch switch Lighting switch PASS
Ground Output
(Y) OUTPUT 4 (Wiper intermit-
tent dial 4)
Turn signal switch LH
JPMIA0035GB
10.7 V
149*5 Ground
Tire pressure warn-
Input Ignition switch ON
(W) ing check switch
JPMIA0011GB
11.8 V
OFF (When driver door

150 Driver door closes)
Ground Driver door switch Input
(SB) switch
JPMIA0011GB
11.8 V
ON (When driver door
0V
opens)

< ECU DIAGNOSIS >
Input/ Condition
+ – Output
151 Rear window defog- Rear window de- Active 0V

(G)
Ground
ger relay control
Output
fogger
B
Not activated Battery voltage
NOTE:
• *1: With Intelligent Key system C
• *2: Without Intelligent Key system
• *3: With auto light system
• *4: Without BOSE audio system D
• *5: With TPMS
Wiring Diagram - BCM - INFOID:0000000003470028
E
UP TO VIN: JN8AZ18U*9W100000, JN8AZ18W*9W200000 (EXCEPT FOR MEXICO),
WCS

< ECU DIAGNOSIS >
JCMWM3152GB

< ECU DIAGNOSIS >
WCS
JCMWM3153GB

< ECU DIAGNOSIS >
JCMWM3154GB

< ECU DIAGNOSIS >
WCS
JCMWM3155GB

< ECU DIAGNOSIS >
JCMWM3156GB

< ECU DIAGNOSIS >
WCS
JCMWM3157GB

< ECU DIAGNOSIS >
JCMWM3158GB
FROM VIN: JN8AZ18U*9W100001, JN8AZ18W*9W200001 (EXCEPT FOR MEXICO),

< ECU DIAGNOSIS >
A
WCS
JCMWM3159GB
P

< ECU DIAGNOSIS >
JCMWM3160GB

< ECU DIAGNOSIS >
WCS
JCMWM3161GB

< ECU DIAGNOSIS >
JCMWM3162GB

< ECU DIAGNOSIS >
WCS
JCMWM3163GB

< ECU DIAGNOSIS >
JCMWM3164GB

< ECU DIAGNOSIS >
WCS
JCMWM3165GB
P
Fail-safe INFOID:0000000003470029
FAIL-SAFE CONTROL BY DTC

BCM performs fail-safe control when any DTC are detected.

< ECU DIAGNOSIS >
Display contents of CONSULT Fail-safe Cancellation

B2013: ID DISCORD BCM-S/L Inhibit engine cranking Erase DTC
B2014: CHAIN OF S/L-BCM Inhibit engine cranking Erase DTC
B2190: NATS ANTENNA AMP Inhibit engine cranking Erase DTC
B2191: DIFFERENCE OF KEY Inhibit engine cranking Erase DTC
B2192: ID DISCORD BCM-ECM Inhibit engine cranking Erase DTC
B2193: CHAIN OF BCM-ECM Inhibit engine cranking Erase DTC
B2195: ANTI SCANNING Inhibit engine cranking Ignition switch ON → OFF
When normal vehicle speed signals are received from ABS actua-
B2557: VEHICLE SPEED Inhibit steering lock
tor and electric unit (control unit) for 500 ms
500 ms after the following CAN signal communication status be-
comes consistent
B2560: STARTER CONT RELAY Inhibit engine cranking
• Starter control relay signal
• Starter relay status signal
500 ms after the following signal reception status becomes consis-
tent
B2601: SHIFT POSITION Inhibit steering lock
• Selector lever P position switch signal
• P range signal (CAN)
5 seconds after the following BCM recognition conditions are ful-
filled
• Ignition switch is in the ON position
B2602: SHIFT POSITION Inhibit steering lock
• Selector lever P position switch signal: Except P position (battery
voltage)
• Vehicle speed: 4 km/h (2.5 MPH) or more
500 ms after the following BCM recognition conditions are fulfilled
B2603: SHIFT POSI STATUS Inhibit steering lock • Selector lever P position switch signal: Except P position (battery
voltage)
• Selector lever P/N position signal: Except P and N positions (0 V)
500 ms after any of the following BCM recognition conditions are
fulfilled
• Status 1
- Ignition switch is in the ON position
- Selector lever P/N position signal: P and N position (battery volt-
B2604: PNP SW Inhibit steering lock age)
- P range signal or N range signal (CAN): ON
• Status 2
- Selector lever P/N position signal: Except P and N positions (0 V)
- P range signal and N range signal (CAN): OFF
500 ms after any of the following BCM recognition conditions are
fulfilled
- Power position: IGN
- Selector lever P/N position signal: Except P and N positions (0 V)
B2605: PNP SW Inhibit steering lock - Interlock/PNP switch signal (CAN): OFF
• Status 2
- Selector lever P/N position signal: P or N position (battery volt-
age)
- PNP switch signal (CAN): ON
comes consistent
B2606: S/L RELAY Inhibit engine cranking
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal)

< ECU DIAGNOSIS >
Display contents of CONSULT Fail-safe Cancellation
A
comes consistent
B2607: S/L RELAY Inhibit engine cranking
• Steering lock relay signal (Request signal)
• Steering lock relay signal (Condition signal) B
500 ms after the following signal communication status becomes
consistent
B2608: STARTER RELAY Inhibit engine cranking
• Starter motor relay control signal
• Starter relay status signal (CAN)
C
When the following steering lock conditions agree
• Inhibit engine cranking • BCM steering lock control status
B2609: S/L STATUS D
• Inhibit steering lock • Steering lock condition No. 1 signal status
• Steering lock condition No. 2 signal status
500 ms after the following conditions are fulfilled
• IGN relay (IPDM E/R) control signal: OFF (Battery voltage) E
B260A: IGNITION RELAY Inhibit engine cranking
• Ignition ON signal (CAN to IPDM E/R): OFF (Request signal)
• Ignition ON signal (CAN from IPDM E/R): OFF (Condition signal)
Maintains the power supply When any of the following conditions are fulfilled
B260F: ENG STATE SIG LOST position attained at the time • Power position changes to ACC
F
of DTC detection • Receives engine status signal (CAN)
When any of the following conditions are fulfilled
• Steering lock unit status signal (CAN) is received normally G
• Inhibit engine cranking
B2612: S/L STATUS • The BCM steering lock control status matches the steering lock
• Inhibit steering lock
status recognized by the steering lock unit status signal (CAN
from IPDM E/R)
H
1 second after the starter motor relay control inside BCM becomes
B2617: STARTER RELAY CIRC Inhibit engine cranking
normal
1 second after the ignition relay (IPDM E/R) control inside BCM be-
B2618: BCM Inhibit engine cranking I
comes normal
1 second after the steering lock unit power supply output control in-
B2619: BCM Inhibit engine cranking
side BCM becomes normal
J
B261E: VEHICLE TYPE Inhibit engine cranking BCM initialization
When BCM transmits the LOCK request signal to steering lock unit,
and receives LOCK response signal from steering lock unit, the fol-
B26E9: S/L STATUS
• Inhibit engine cranking
lowing conditions are fulfilled
K
• Inhibit steering lock
• Steering condition No. 1 signal: LOCK (0V)
• Steering condition No. 2 signal: LOCK (Battery voltage)
L
HIGH FLASHER OPERATION
BCM detects the turn signal lamp circuit status by the current value.
BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn signal
lamp operating. M
NOTE:
The blinking speed is normal while activating the hazard warning lamp.
FAIL-SAFE CONTROL BY RAIN SENSOR MALFUNCTION WCS
• BCM judges the rain sensor serial link error by the rain sensor serial link condition and detects the rain sen-
sor malfunction by rain sensor malfunction signal.
• When BCM detects the rain sensor serial link error or the rain sensor malfunction while front wiper AUTO O
operation, BCM operates a fail-safe control.
NOTE:
If rain sensor malfunction is detected when ignition switch is turned OFF ⇒ ON and front wiper switch is INT/
AUTO position, BCM operates a fail-safe control. P
REAR WIPER MOTOR PROTECTION

BCM detects the rear wiper stopping position according to the rear wiper stop position signal.
When the rear wiper stop position signal does not change for more than 5 seconds while driving the rear
wiper, BCM stops power supply to protect the rear wiper motor.
Condition of cancellation
1. More than 1 minute is passed after the rear wiper stop.

< ECU DIAGNOSIS >
2. Turn rear wiper switch OFF.
3. Operate the rear wiper switch or rear washer switch.
DTC Inspection Priority Chart INFOID:0000000003470030
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
Priority DTC
1 B2562: LOW VOLTAGE
• U1000: CAN COMM CIRCUIT
2
• U1010: CONTROL UNIT (CAN)
• B2190: NATS ANTENNA AMP
• B2191: DIFFERENCE OF KEY
3 • B2192: ID DISCORD BCM-ECM
• B2193: CHAIN OF BCM-ECM
• B2195: ANTI SCANNING
• B2013: ID DISCORD BCM-S/L
• B2014: CHAIN OF S/L-BCM
• B2553: IGNITION RELAY
• B2555: STOP LAMP
• B2556: PUSH-BTN IGN SW
• B2557: VEHICLE SPEED
• B2560: STARTER CONT RELAY
• B2601: SHIFT POSITION
• B2602: SHIFT POSITION
• B2603: SHIFT POSI STATUS
• B2604: PNP SW
• B2605: PNP SW
• B2606: S/L RELAY
• B2607: S/L RELAY
• B2608: STARTER RELAY
• B2609: S/L STATUS
• B260A: IGNITION RELAY
4
• B260B: STEERING LOCK UNIT
• B260C: STEERING LOCK UNIT
• B260D: STEERING LOCK UNIT
• B260F: ENG STATE SIG LOST
• B2612: S/L STATUS
• B2614: ACC RELAY CIRC
• B2615: BLOWER RELAY CIRC
• B2616: IGN RELAY CIRC
• B2617: STARTER RELAY CIRC
• B2618: BCM
• B2619: BCM
• B261A: PUSH-BTN IGN SW
• B261E: VEHICLE TYPE
• B26E9: S/L STATUS
• B26EA: KEY REGISTRATION
• C1729: VHCL SPEED SIG ERR
• U0415: VEHICLE SPEED SIG

< ECU DIAGNOSIS >
Priority DTC
A
• C1704: LOW PRESSURE FL
• C1705: LOW PRESSURE FR
• C1706: LOW PRESSURE RR
• C1707: LOW PRESSURE RL B
• C1708: [NO DATA] FL
• C1709: [NO DATA] FR
• C1710: [NO DATA] RR
• C1711: [NO DATA] RL C
• C1712: [CHECKSUM ERR] FL
• C1713: [CHECKSUM ERR] FR
• C1714: [CHECKSUM ERR] RR
• C1715: [CHECKSUM ERR] RL D
5 • C1716: [PRESSDATA ERR] FL
• C1717: [PRESSDATA ERR] FR
• C1718: [PRESSDATA ERR] RR
• C1719: [PRESSDATA ERR] RL
E
• C1720: [CODE ERR] FL
• C1721: [CODE ERR] FR
• C1722: [CODE ERR] RR
F
• C1723: [CODE ERR] RL
• C1724: [BATT VOLT LOW] FL
• C1725: [BATT VOLT LOW] FR
• C1726: [BATT VOLT LOW] RR G
• C1727: [BATT VOLT LOW] RL
• C1734: CONTROL UNIT
• B2621: INSIDE ANTENNA
H
6 • B2622: INSIDE ANTENNA
• B2623: INSIDE ANTENNA
DTC Index INFOID:0000000003470031 I
NOTE:
The details of time display are as follows.
J
• CRNT: A malfunction is detected now.
• PAST: A malfunction was detected in the past.
IGN counter is displayed on Freeze Frame Data. For details of Freeze Frame Data, refer to BCS-17, "COM-
MON ITEM : CONSULT-III Function (BCM - COMMON ITEM)". K
Freeze Frame
Data
Tire pressure L
•Vehicle Speed Intelligent Key Reference
CONSULT display Fail-safe monitor warning
•Odo/Trip Meter warning lamp ON page
lamp ON
•Vehicle Condi-
tion M
No DTC is detected.
further testing — — — — —
may be required.
WCS
U1000: CAN COMM CIRCUIT — — — — BCS-40
U1010: CONTROL UNIT (CAN) — — — — BCS-41
U0415: VEHICLE SPEED SIG — — — — BCS-42 O
B2013: ID DISCORD BCM-S/L × × — — SEC-55
B2014: CHAIN OF S/L-BCM × × — — SEC-56
P
B2190: NATS ANTENNA AMP × — — — SEC-47
B2191: DIFFERENCE OF KEY × — — — SEC-50
B2192: ID DISCORD BCM-ECM × — — — SEC-51
B2193: CHAIN OF BCM-ECM × — — — SEC-53
B2195: ANTI SCANNING × — — — SEC-54
B2553: IGNITION RELAY — × — — PCS-49

< ECU DIAGNOSIS >
Freeze Frame
Data
Tire pressure
lamp ON
•Vehicle Condi-
tion
B2555: STOP LAMP — × — — SEC-59
B2556: PUSH-BTN IGN SW — × × — SEC-61
B2557: VEHICLE SPEED × × × — SEC-63
B2560: STARTER CONT RELAY × × × — SEC-64
B2562: LOW VOLTAGE — × — — BCS-43
B2601: SHIFT POSITION × × × — SEC-65
B2602: SHIFT POSITION × × × — SEC-68
B2603: SHIFT POSI STATUS × × × — SEC-70
B2604: PNP SW × × × — SEC-73
B2605: PNP SW × × × — SEC-75
B2606: S/L RELAY × × × — SEC-77
B2607: S/L RELAY × × × — SEC-78
B2608: STARTER RELAY × × × — SEC-80
B2609: S/L STATUS × × × — SEC-82
B260A: IGNITION RELAY × × × — PCS-51
B260B: STEERING LOCK UNIT — × × — SEC-86
B260C: STEERING LOCK UNIT — × × — SEC-87
B260D: STEERING LOCK UNIT — × × — SEC-88
B260F: ENG STATE SIG LOST × × × — SEC-89
B2612: S/L STATUS × × × — SEC-92
B2614: ACC RELAY CIRC — × × — PCS-53
B2615: BLOWER RELAY CIRC — × × — PCS-56
B2616: IGN RELAY CIRC — × × — PCS-59
B2617: STARTER RELAY CIRC × × × — SEC-96
B2618: BCM × × × — PCS-62
B2619: BCM × × × — SEC-98
B261A: PUSH-BTN IGN SW — × × — SEC-99
× (Turn ON for 15
B261E: VEHICLE TYPE × × — SEC-102
seconds)
B2621: INSIDE ANTENNA — × — — DLK-95
× (Turn ON for 15
B26E9: S/L STATUS × × — SEC-90
seconds)
× (Turn ON for 15
B26EA: KEY REGISTRATION — × — SEC-91
seconds)
C1704: LOW PRESSURE FL — — — ×
C1705: LOW PRESSURE FR — — — ×
WT-16
C1706: LOW PRESSURE RR — — — ×
C1707: LOW PRESSURE RL — — — ×

< ECU DIAGNOSIS >
Freeze Frame
Data A
Tire pressure
lamp ON
•Vehicle Condi-
tion B
C1708: [NO DATA] FL — — — ×
C1709: [NO DATA] FR — — — ×
WT-18 C
C1710: [NO DATA] RR — — — ×
C1711: [NO DATA] RL — — — ×
C1712: [CHECKSUM ERR] FL — — — × D
C1713: [CHECKSUM ERR] FR — — — ×
WT-21
C1714: [CHECKSUM ERR] RR — — — ×
E
C1715: [CHECKSUM ERR] RL — — — ×
C1716: [PRESSDATA ERR] FL — — — ×
C1717: [PRESSDATA ERR] FR — — — × F
WT-24
C1718: [PRESSDATA ERR] RR — — — ×
C1719: [PRESSDATA ERR] RL — — — ×
G
C1720: [CODE ERR] FL — — — ×
C1721: [CODE ERR] FR — — — ×
WT-26
C1722: [CODE ERR] RR — — — × H
C1723: [CODE ERR] RL — — — ×
C1724: [BATT VOLT LOW] FL — — — ×
C1725: [BATT VOLT LOW] FR — — — × I
WT-29
C1726: [BATT VOLT LOW] RR — — — ×
C1727: [BATT VOLT LOW] RL — — — ×
J
C1729: VHCL SPEED SIG ERR — — — × WT-32
C1734: CONTROL UNIT — — — × WT-33
K
WCS

THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
< SYMPTOM DIAGNOSIS >
SYMPTOM DIAGNOSIS
THE PARKING BRAKE RELEASE WARNING CONTINUES SOUNDING, OR
DOES NOT SOUND
• The parking brake warning buzzer sounds continuously during vehicle travel though the parking brake is
released.
• The parking brake warning buzzer does not sound at all even though driving the vehicle with the parking
brake applied.
1.CHECK PARKING BRAKE WARNING LAMP

1. Start the engine.
2. Check the operation of the brake warning lamp by operating the parking brake.
When parking brake is applied : ON

When parking brake is released : OFF
YES >> Replace the combination meter.
NO >> GO TO 2.
2.CHECK PARKING BRAKE SWITCH SIGNAL CIRCUIT
Perform a check for the parking brake switch signal circuit. Refer to MWI-54, "Diagnosis Procedure".
YES >> GO TO 3.
3.CHECK PARKING BRAKE SWITCH
Perform a unit check for the parking brake switch. Refer to BRC-80, "Component Inspection".
NO >> Replace the parking brake switch. Refer to PB-6, "Removal and Installation".

THE LIGHT REMINDER WARNING DOES NOT SOUND
THE LIGHT REMINDER WARNING DOES NOT SOUND
A
Light reminder warning chime does not sound even though headlamp is illuminated. B
1.CHECK COMBINATION SWITCH (LIGHT SWITCH) OPERATION C

Check that the headlamps operate normally by operating the combination switch (light switch).
Do they operate normally?
D
YES >> GO TO 2.
NO >> Refer to EXL-162, "Diagnosis Procedure".
2.CHECK FRONT DOOR SWITCH (DRIVER SIDE) SIGNAL CIRCUIT E
Perform the check for the front door switch (driver side) signal circuit. Refer to DLK-103, "WITH AUTOMATIC
BACK DOOR : Diagnosis Procedure".
Is the inspection result normal? F
YES >> GO TO 3.
3.CHECK FRONT DOOR SWITCH (DRIVER SIDE) G
Perform a unit check for the front door switch (driver side). Refer to DLK-105, "WITH AUTOMATIC BACK
DOOR : Component Inspection".
H
YES >> Replace the BCM. Refer to BCS-96, "Removal and Installation".
NO >> Replace the front door switch (driver side). Refer to DLK-368, "Removal and Installation".
I
WCS

THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT SOUND
THE SEAT BELT WARNING CONTINUES SOUNDING, OR DOES NOT
SOUND
• Seat belt reminder warning does not sound.

• Seat belt reminder warning sounds continuously.
1.CHECK SEAT BELT WARNING LAMP

1. Turn ignition switch ON.
2. Check the operation of the seat belt warning lamp in the combination meter.
Seat belt fastened : OFF

Seat belt not fastened : ON
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK BCM OUTPUT SIGNAL
Check if the light reminder warning chime is activated by performing BCM active test. Refer to WCS-20,
"BUZZER : CONSULT-III Function (BCM - BUZZER)".
NO >> GO TO 3.
Check if buzzer switches to proper condition (On/Off) on data monitor of combination meter. Refer to WCS-15,
"CONSULT-III Function (METER/M&A)".
Buzzer active condition : On

Buzzer non-active condition : Off
NO >> Replace the BCM. Refer to BCS-96, "Removal and Installation".
4.CHECK SEAT BELT BUCKLE SWITCH CIRCUIT
Perform the check for the seat belt buckle switch circuit. Refer to WCS-25, "Diagnosis Procedure".
YES >> GO TO 5.
5.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)
Perform a unit check for the seat belt buckle switch (driver side). Refer to WCS-26, "Component Inspection".
NO >> Replace the seat belt buckle.Refer to SB-7, "SEAT BELT BUCKLE : Removal and Installation".

THE KEY WARNING DOES NOT SOUND
THE KEY WARNING DOES NOT SOUND
A
The is key warning chime does not sound under the following conditions. B
• Key inserted into the key slot. (Key slot switch ON)
• Ignition switch is not in ON or START. (Ignition switch signal OFF)
• Front door switch (driver side) is open. [Door switch signal (driver side) ON]
C
1.CHECK BCM INPUT SIGNAL D

1. Connect CONSULT-III.
2. Select the “Data Monitor” of “BCM (BUZZER)” and check the “KEY SW-SLOT” monitor value. Refer to
WCS-49, "Reference Value". E
YES >> Replace BCM. Refer to BCS-96, "Removal and Installation".
NO >> GO TO 2. F
2.CHECK KEY SLOT SWITCH SIGNAL CIRCUIT
Check the key slot switch signal circuit. Refer to DLK-423, "Diagnosis Procedure".
G
YES >> GO TO 3.
NO >> Check applicable parts, and repair or replace corresponding parts.
H
3.CHECK DOOR SWITCH SIGNAL (DRIVER SIDE) CIRCUIT
Check the door switch signal (driver side) circuit. Refer to DLK-103, "WITH AUTOMATIC BACK DOOR : Diag-
nosis Procedure". I
YES >> GO TO 4.
NO >> Repair harness or connector. J
4.CHECK FRONT DOOR SWITCH (DRIVER SIDE)
Check the front door switch (driver side). Refer to DLK-105, "WITH AUTOMATIC BACK DOOR : Component
K
Inspection".
YES >> Replace BCM. Refer to BCS-96, "Removal and Installation". L
NO >> Replace front door switch (driver side). Refer to DLK-368, "Exploded View".
WCS

PRECAUTIONS
< PRECAUTION >
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER" INFOID:0000000003470036
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIRBAG” and
“SEAT BELT” of this Service Manual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIRBAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors while ignition switch is
ON or engine is running, never use air or electric power tools or strike near the sensor(s) with a hammer.
Heavy vibration may activate the sensor(s), deploy the airbag(s), possibly cause serious injury.
When using air or electric power tools or hammers, always turn OFF ignition switch, disconnect the battery,
and wait 3 minutes or more before performing any service.

WCS Murano

Uploaded by

Copyright:

Available Formats

WCS Murano

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

WCS Murano

Uploaded by

Copyright:

Available Formats

DRIVER INFORMATION & MULTIMEDIA

Revision: 2008 October WCS-1 2009 Murano

Revision: 2008 October WCS-2 2009 Murano

Revision: 2008 October WCS-3 2009 Murano

Revision: 2008 October WCS-4 2009 Murano

WARNING CHIME SYSTEM : System Description INFOID:0000000003465221

Revision: 2008 October WCS-5 2009 Murano

Warning functions Signal name

Revision: 2008 October WCS-6 2009 Murano

Revision: 2008 October WCS-7 2009 Murano

LIGHT REMINDER WARNING CHIME : Component Description INFOID:0000000003465398

SEAT BELT WARNING CHIME

Revision: 2008 October WCS-8 2009 Murano

SEAT BELT WARNING CHIME : System Description INFOID:0000000003465318

WARNING CANCEL CONDITIONS

Revision: 2008 October WCS-9 2009 Murano

SEAT BELT WARNING CHIME : Component Description INFOID:0000000003465346

PARKING BRAKE RELEASE WARNING CHIME

Revision: 2008 October WCS-10 2009 Murano

Warning is canceled if any of the following conditions are fulfilled.

Revision: 2008 October WCS-11 2009 Murano

PARKING BRAKE RELEASE WARNING CHIME : Component Description INFOID:0000000003465451

KEY WARNING CHIME

Revision: 2008 October WCS-12 2009 Murano

Revision: 2008 October WCS-13 2009 Murano

KEY WARNING CHIME : Component Description INFOID:0000000003465353

Revision: 2008 October WCS-14 2009 Murano

CONSULT-III APPLICATION ITEMS B

System Diagnosis mode Description C

SELF DIAG RESULT

Revision: 2008 October WCS-15 2009 Murano

Revision: 2008 October WCS-16 2009 Murano

Display item Description H

Display item Description M

Revision: 2008 October WCS-17 2009 Murano

Revision: 2008 October WCS-18 2009 Murano

Revision: 2008 October WCS-19 2009 Murano

FREEZE FRAME DATA (FFD)

CONSULT screen item Indication/Unit Description

CONSULT-III APPLICATION ITEMS

Test item Diagnosis mode Description

Revision: 2008 October WCS-20 2009 Murano

Revision: 2008 October WCS-21 2009 Murano

Power source Fuse No.

1.CHECK FUSE AND FUSIBLE LINK

Revision: 2008 October WCS-22 2009 Murano

Signal name Fuse and fusible link No. A

Revision: 2008 October WCS-23 2009 Murano

1.CHECK OPERATION OF METER BUZZER

1.CHECK POWER SUPPLY OF COMBINATION METER

Revision: 2008 October WCS-24 2009 Murano

1.CHECK COMBINATION METER INPUT SIGNAL C

>> INSPECTION END

1.CHECK COMBINATION METER INPUT SIGNAL

2.CHECK SEAT BELT BUCKLE SWITCH CIRCUIT

Revision: 2008 October WCS-25 2009 Murano

1.CHECK SEAT BELT BUCKLE SWITCH (DRIVER SIDE)

B409*1 15*1 B409*1 16*1

B409*1 15*1 B409*1 16*1

B4091 151 B4091 161

B4091 151 B4091 161