Bearing and Sealing Components: For Mechanical Engineering
Bearing and Sealing Components: For Mechanical Engineering
Bearing and Sealing Components: For Mechanical Engineering
Carbon and graphite materials are a proven method for the sealing of shafts and their bearings.
The special physical and mechanical properties of carbon and graphite, in particular their low coeffi-
cient of friction, hard wearing and excellent thermal resistance offer solutions to many mechanical
engineering and manufacturing problems.
Bearings, sealing rings and vanes made of carbon and graphite may be used for dry or wet running
applications. Their use is recommended where the following conditions prevail:
dry running and high pressure demands a mechanically sound material with sufficient self-
lubricating capability, good thermal conductivity and low coefficient of expansion
bearings are situated vertically or at an angle in the machine thus making lubricant retention
difficult
Bearings and sealing elements made from Graphite COVA materials give the designer many oppor-
tunities for solving difficult bearing and sealing problems.
OPERATING TEMPERATURE
The temperature resistance in an oxidizing atmosphere can be specified as 500°C maximum for Gra-
phite COVA bearing qualities. In a non-oxidizing atmosphere the temperature resistance is deter-
mined by the final graphitizing treatment of each individual grade (e.g. upper application limit for
graphite is approximately 3000°C). Temperature resistance is also affected by various impregnations.
In the case of resin impregnation the maximum operating temperature is 180°C, for lead impregna-
tion 200°C and antimony impregnation 500°C.
CHEMICAL RESISTANCE
Carbon and particularly graphite are characterised by excellent chemical resistance to almost all or-
ganic and inorganic media. Exceptions to this are some strongly oxidising acids, alkaline solutions,
halogens and alkali molten metal.
Graphite has self-lubricating properties because of its crystalline structure. The low friction coeffi-
cient is a function of the low bonding between the structural lattice planes. Dislocation of one
against the other is therefore easy. The friction coefficient is particularly low if traces of water or
other vapours are present. The friction coefficient is greatly increased when a vacuum is created.
Because of the varying conditions of application, no exact data can be given for friction coefficients.
In general the following values can be expected for sliding friction:
The frictional behaviour of carbon and graphite is also affected by the following factors:
running in
specific pressure
running speed
When running in carbon and graphite bearings, the friction coefficient drops until a constant value is
reached once the surfaces are smoothed.
The coefficient of friction also drops in the case of constant specific strain and increasing running
speed, or at the inverse.
0,30
0,25
friction coefficient µ
0,10
0,05
0,00
0 5 10 15 20 25 30 35 40 45 50
running time [min] Fig. 1
0,30
0,25
0,20
0,15
0,10
0,05
0,00
0 2 4 6 8 10 12
mean running speed[m/s] Fig. 2
The good machining properties of graphite give the designer full scope in producing practical designs.
The following guidelines should be observed:
Wall thickness: The choice of wall thickness depends on mechanical aspects. Based on practical
operating experience, the graphite bearings should have wall thicknesses which
correspond roughly to the empirical equation S = 0.13d + 2.8 ≥ 3 (mm)
Bearing length: To avoid excessive edge pressure and internal stress in the bearing L = d; L ≤ 2d
is recommended. The height for washers is recommended as L = 0.1 D • L ≥ 3
(mm).
Flanges: Flange thickness b should be at least as much as wall thickness s (b ≥ s). Flange
connections should be radiused and adjoining surfaces machined.
As a general rule: No sharp corners, should be broken or radiused. Shapes should be as simple as
possible.
The surface quality of the counter face materials has an important influence on the durability of car-
bon and graphite. Counter face surfaces with a maximum surface roughness of Sr <1 μm are recom-
mended. For high pressure lapped and superfinished counter faces with a maximum surface rough-
ness of Sr<0.5 μm are necessary.
Carbon and graphite can be machined to fine tolerances on most machines and machine tools. The
work piece remains both structurally and dimensionally stable.
Extraction: Care must be taken that all dust is extracted during machining (e.g. by an indus-
trial vacuum cleaner with a rating of at least 30 mbar and 20 m/s air speed). Lu-
bricated machine driving elements must be covered, moving parts or platens
must be kept grease and oil free.
Cooling: The use of cutting lubricants and cooling agents is not recommended. Water
may be used as a coolant for honing, lapping and occasionally for cutting and
separating.
Clamping: The parts must be carefully and lightly clamped, the clamping pressure should
be distributed over as large an area as possible. Parts with a low wall thickness
(<0.1 d or <10 mm) must be pre-pared internally with collet chucks or expanding
rings. For external treatment it is advisable to place the part on a mandrel.
Tools: The following values generally apply to all turning, drilling and milling tools:
clearance angle α: 15° ... 25°; wedge angle ß: 65° ... 75°; tool orthogonal plane γ:
± 2°, large cutting radii prevent chipping of the work piece. The use of K 05 and K
10 types of hard metal and diamond tools are recommended.
Carbon and graphite can easily be lapped and honed allowing fine tolerances.
The use of carbon and graphite bearings has proved successful in the areas of mechanical and
process engineering. The use of Graphite Cova bearing materials is recommended for the following
conditions:
The design of radial bearings and collar bearings of carbon and graphite is determined by DIN 1850,
Section 4, „Bushes for slide bearings made of artificial carbon". Instructions for the location of lubri-
cation grooves are contained in DIN 1850, Section 2 and DIN 1591.
It Is recommended that bores are smooth for dry-running radial and axial bearings. Wet running car-
bon radial bearings can be provided with longitudinal grooves specific to each case. Grooves are rec-
ommended for wet running axial bearings.
Normally the bearings are shrunk or pressed directly into the housing or into metal bushings. The low
thermal expansion coefficient of carbon and graphite (3 ... 5 x 10-6/K) must be taken into account
when shrinking or pressing in the bearings.
COLD PRESSING
For a cold press fit in steel, where the application is lower than 100°C steel housings made to H7 bore
tolerance are normally recommended. If the housing material has a higher coefficient of thermal
expansion than steel the temperature limitation is normally lower.
When pressing the bearing into its housing a mandrel with collar whose diameter is approximately
three tolerances be-low the drilling tolerance of the carbon bearings as supplied should be used to
press the bearings in. The bore diminishes by 70 - 85% of the pressing over-dimension according to
the quality and dimension of the bearing.
SHRINKING
We recommend shrinking directly into the metal housing for carbon bearings which are to be used at
operational temperatures of over 100°C. To shrink in the bearings, experience has shown that the
tolerance overlap should be in the range corresponding to H7/x8 ... z8. The selected heating temper-
ature for mounting must be sufficiently high to allow the cold bearing to be easily inserted. On
shrinking, the carbon bearing bore diminishes by approximately 80 ... 100 % of the shrinking over-
dimension. In the case of the above mentioned shrink fits H7/x8 ... z8, this diminishes according to
the wall thickness ratio. In order to keep to exact tolerances it is advisable to machine the bearing
bore to size after shrinking.
ADHESIVES
Adhesives are only suitable for bearings which are subject to low temperatures (up to 200°C). Bond-
ing to the housing with commercially available adhesives (e.g. Technicol 8280) is possible. For higher
temperatures Graphite Cova special coking adhesives should be used.
The permissible bearing pressure is determined by the surface speed of the shaft and the friction
ratio of the carbon or graphite bearings. The permissible pressure values for dry-running
dry bearings
have been determined by laboratory trials. The corresponding values can be seen in the following p •
v-diagram
diagram (Fig. 5). The permissible bearing wear rate was selected as 1 (chrome steel) µm/h. In prac-
pra
tice
ice the media often increases lubrication. This means that the values in the p • v-diagram
v can be
increased considerably whilst wear remains constant.
Graphite Cova carbon and graphite seals have been used successfully in mechanical engineering for
many years. Because of their self-lubricating properties and good corrosion and thermal resistance,
Graphite Cova seals are used for rotating and reciprocating parts.
Graphite Cova seals are particularly suitable for the following application conditions where:
These seals can be subdivided according to the following designs (construction features):
In chemical processing technology, dry running piston compressors are becoming increasingly used
for the compression of extremely cold liquified gases. Great importance is placed on good dry run-
ning properties for this process. Graphite Cova carbon and graphite meet these requirements fully.
One-piece, split or multi-piece rings with overlapped or tenon joints are used to seal the piston or
guide rods. With GraphiteCOVA rings dry running Operation times of over 10,000 hours can be
achieved for the compression of gases with normal moisture content (dew point approximately 0°C).
With drier gases the life of the piston and guide rings is reduced. (Carbon and graphite can be used to
a dew point of –60°C).
Piston speed should not exceed 4m/s. Extremely high wear of the piston rings must be expected if
piston speeds are high.
In order to achieve an even and long lasting sealing it is necessary to provide the counter faces with
as fine a surface finish as possible, e.g. by lapping or honing. (Sr < 1.0 µm). Increased surface rough-
ness can lead to higher wear rates.
For radial sealing rings there are a number of tried and tested metal springs, the choice of materials
depends on the prevailing operational conditions. The springs are used to press the carbon rings ra-
dially against the cylinder wall and must be designed for a contact pressure of approx. 1.0 ... 1.5
N/cm2.
Carbon and graphite piston rings are supplied as single rings, slit or multi piece with overlap and (if
necessary) additional mortising. Fig. 6 provides a diagrammatic view of the various types of joints.
The angled butt joint (Design a) is generally preferred as it can be machined at lower cost and allows
slightly lower penetration than a straight butt joint. When there are great differences in pressure and
low piston speeds, either the overlapped join (Design b) or the overlapped mortised joint (Design d)
is used.
DESIGN B
DESIGN C
DESIGN D
The packing glands previously used have been largely replaced by mechanical seals for axial sealing.
Mechanical seals are mainly used for high speed sealing between liquids and gases. For sealing
against gases, chemically aggressive or strongly heated media, the use of double action mechanical
seals is recommended. The trapped media between the two surfaces aids the lubrication of the two
surfaces, conducts heat caused by friction and improves the sealing effect.
A mechanical seal comprises the following main components:
The diameter of the counter face should be the same or larger than that of the carbon ring. The finish
of the carbon wearing surface and of the counter face is critical to the relative wear rate. Lapped
opposing surfaces have proved successful in practice.
After the running-in phase, long-term wear averages at 0.03 ... 0.20 µm/h. Since the long-term wear
of mechanical carbon seals is extremely low, it is very difficult to draw conclusions from laboratory
trials as to the service life of the rings because results vary greatly. The rate of wear depends upon a
number of variable factors such as material combination, temperature conditions, frictional behav-
iour etc. In practice it h as, however been seen that if the axial sliding rings are working perfectly and
the correct quality is chosen, a service life of many years can be expected of Graphite Cova mechani-
cal carbon seals and counter faces.
Impregnated sealing rings are well proven for normal working conditions. For particularly high pres-
sure requirements we also supply gas-tight rings which are inspected for leaks.
When shrinking or pressing GraphiteCOVA carbon face seals into metal housings, the same points
must be considered as for carbon bearings (see page 10). A shrink fit does not always provide suffi-
cient guarantee of axial tightness. In such cases it is better to bond the carbon face seals into the
housing.
Fig. 8: The sealing principle of a single action sliding ring with carbon ring
Paper Industry
Textile Industry
Rubber Industry
Chemical Industry
are provided with carbon packing rings pressed laterally onto the steam inlet and outlet vents in
proven designs. The single seals generally have concave or convex surfaces because this design al-
lows the packing rings to adjust to the oscillation of calender drums.
Fig. 9 shows the installation principle of carbon sealing rings in the heating joints of calender driers.
This location has the advantage that the external and internal steam supply pipes move indepen-
dently and that differences in length due to temperature can be compensated.
The sliding surfaces of Graphite Cova carbon seals attain the surface quality necessary for sealing
after only a short running-in period. Fig. 11 shows the almost polished smooth running surface of a
carbon sealing lens after approx. 10,000 hours of oper-
ation.
Graphite Cova produces one-piece rings of carbon and
graphite for steam seals to popular designs in proven
grades at economic prices.
For oil free, steam lubricated seals we recommend
grade B 525; for the opposing bearings without steam
lubrication we recommend grade B 520 DXT. Fig. 9: Diagrammatic view of the installation of a car-
bon sealing ring in the heating joint of a calend-
er drier
Fig. 11: Carbon steam seals Fig. 10: Running surface of a carbon sealing ring
after 10.000 hours of operation
Hydroelectric Power Stations have vertical or horizontal Francis or Kaplan turbines which transfer the
hydrodynamic power to 3 phase generators.
The turbine shaft is sealed with carbon rings. These are composed of several segments with free
movement between the joints. To prevent these being pushed together in Operation, each segment
is fixed to the casing wall. The contact pressure of the rings should lie between 1.5 ... 2.0 N/cm2.
Similar constructions are also used for large pump turbines. Graphite COVA manufacture rings of up
to 30 segments with diameters of up to 4,000 mm for this field of application.
The following figure shows overlapped-tenoned carbon ring segments for shaft sealing on water tur-
bines.
Fig. 12: Overlapped-tenoned carbon segments for shaft sealing on water turbines
Packing rings are divided into two types, those with shaft clearance (with gaps) and those in contact
with the shaft. When calculating the bore tolerances, allowance should be made for carbon and gra-
phite having a much lower thermal expansion coefficient (3 ... 5 x 10-6/K) than metals.
The contact pressure of the carbon rings to the cylinder necessary to achieve a good sealing effect is
attained with the use of a garter spring.
Wire thickness of 0.2... 1.5 mm are used. Calculation of the Spiral tension spring can be based on a
maximum permissible contact pressure of the carbon ring on the cylinder of 1 ... 1.5 N/cm2. The seal-
ing rings must be secured against torsion.
r = working radius
t = groove depth
n = number of segments
S = total gap (S1 = s/n)
Fig. 14: Dimensioning of a ring and calculation of the garter tension spring
The use of multi-piece carbon rings is preferred for axial sealing of shafts e.g. for steam turbines. In
general 4-8 carbon rings are placed one behind the other and assembled as chamber packings with
the appropriate packing rings.
Fig. 15 shows the front and side views of a four piece carbon packing ring with single tenon joints.
The peripheral groove is for the insertion of the garter spring with which the ring can be radially tigh-
tened onto the shaft. After running in, an extremely narrow ring gap is present between the shaft
and carbon rings. This guarantees a good sealing effect.
In contrast to shaft clearance seals these packing rings are in permanent contact with the shaft. They
are used widely for sealing reciprocating shafts.
With good design Graphite Cova carbon rings wear well. In practical use this means that even in a
„no-maintenance" Operation they will have a long working life and make a very good seal with mini-
mum space requirements.
Fig. 16: Carbon sealing rings with non-radially cut segment joints
Common applications are for handling and dosing of liquids with a low wetting capacity: the Opera-
tion of oil-free com-pressed air tools; air compressors for pneumatic plant, e.g. (in the case of indus-
try) milking machines etc. Carbon has proved superior to other materials in this field thanks to its
outstanding wearing and self-lubricating properties for both wet and dry Operation.
rust and acid resistant steels high temper unalloyed grey cast iron
hard chrome plated running surfaces cast iron with nodular graphite structure
(e.g. Meehanite)
rust proof or heat resistant cast steel
manganese bronze or phosphor bronze
Carbon or graphite sealing elements can be used for many purposes in the mechanical plant of the
paper and pulp industries: suction rolls of paper machines for example are furnished with carbon
sealing strips. High operating times can be achieved with these special machines because of the low
friction factor and the resulting low wear rate of the strips.
Fig. 19: Carbon sealing strips for suction rolls in paper machines
Carbon stripping elements are mainly used in the textile and food industries. The components are
used in dyeing equipment in textile machines, for example to remove the dye from printing calend-
ers. Design Engineers are able to take advantage of the high corrosion resistance of carbon and gra-
phite and of their resistance to many aggressive chemical media.
Guide Rings X X
Piston Rings X X
Steam Seals X X
Contactless Seals X X
Contact Seals X X
Separating Slides X X
Carbon Vanes X X X
Stripping Components X X