Professional Documents
Culture Documents
Group 24 Transfer: 98 Minor Change
Group 24 Transfer: 98 Minor Change
com
Group 24
Transfer
BACK HOME
cardiagn.com
IDLER GEAR AND REAR DRIVE ................................................... 24- 16
24-1
SPECIFICATIONS/STRUCTURE AND OPERATION
SPECIFICATIONS
Item Specifications
Model TF3
Gear ratio HIGH 1.090
LOW 1.987
Gear oil Oil quantity L {qts.} 3.0 {3.2}
Dry mass (including transmission body) kg {lb} Approximately 190 {420}
Control Front drive and HIGH-LOW switching floor change remote control
cardiagn.com
5 Output shaft
6 Output shaft LOW gear
7 Output shaft HIGH gear
3 8 Front drive hub and sleeve
9 Front drive shaft
8
7 6 27272
ON OFF
HIGH LOW
Front drive 06389
HIGH/LOW switching
24-2
24
Transfer Control
2
3
cardiagn.com
4
27273
Move the transfer control lever 1 from left to right to change-over between two-wheel drive and four-wheel drive. Forward
and backward movement changes between HIGH and LOW.
6 5
27274
24-3
TROUBLESHOOTING
Symptoms
cardiagn.com
Possible causes
Front drive shaft and constant sleeve splines worn ●
Hub and HIGH/LOW constant sleeve splines worn ●
Idler shaft bearing worn or damaged ●
Output shaft bearing worn or damaged ●
Drive shaft needle bearing worn or damaged ●
Transfer Gears damaged ●
body faulty Output shaft LOW gear and HIGH gear ●
backlash excessive
Gear oil insufficient ●
Gear oil viscosity unsuitable ●
Constant sleeve and dog clutch cracked ● ●
HIGH/LOW constant sleeve and hub cracked ● ●
Shift rail bent ● ●
Shift rail friction movement poor ● ●
Control mechanism Shift fork bent ● ●
faulty Shift fork claw worn ● ●
Steel ball and shift rail poppet groove worn ●
Poppet spring fatigued or cracked ●
Transfer control Control cable faulty ● ● ● ●
system faulty LOW switch faulty ● ●
Transfer four-wheel drive switch faulty ● ●
Wiring broken or connection poor ● ●
24-4
MEMO
24
24-5
cardiagn.com
REMOVAL AND INSTALLATION OF TRANSFER ASSEMBLY
Ê
9
Ù A
- 1
- 4 Ê
14 12 - -
Ù
* Ê 6 Ê
8 7 Ù Ù
cardiagn.com
13
Ê 11
27275
● Disassembly sequence
1 Bolt 10 Oil seal
2 Air breather 11 Transfer assembly Õ P24-10, 16
3 Needle bearing 12 Distance pipe
4 Transfer input rear cover 13 Bolt
5 Lock nut 14 Extension spacer
6 O-ring
7 Drive shaft gear A : Positioning pin
8 Bolt * : Transmission assembly
9 Bolt Ù : Non-reusable parts
NOTE
• For removal from vehicle, see ^ Gr 10.
• Check backlash of drive shaft gear 7 before disassembly.
• Do not remove needle bearing 3 from transfer input rear cover 4 unless it is faulty.
● Assembly sequence
Follow the disassembly sequence in reverse.
NOTE
Check backlash when assembling parts.
24-6
24
Service standards Unit : mm {in.}
Location Maintenance item Standard value Limit Remedy
7, 11 Drive shaft gear and transfer idler gear backlash 0.08 to 0.22 {0.0031 to 0.0087} 0.50 {0.020} —
cardiagn.com
* Mounting surface of extension spacer transmission assembly THREEBOND 1215 As required
1 Thread area of pierce bolt THREEBOND 1104J As required
4 Mounting surface of transfer assembly transfer input rear cover THREEBOND 1215 As required
10 Lip area of oil seal and transfer assembly Wheel bearing grease As required
[NLGI No.2 (Li soap)]
14 Mounting surface of transfer assembly extension spacer THREEBOND 1215 As required
ø25 {0.98}
ø32.5
{1.28}
50
{1.97}
5 Socket wrench 44490-44101 Removal and installation of transmission
main shaft lock nut
00069
184
ø55.5 {7.24}
{2.19}
ø85
{3.35}
06398
24-7
REMOVAL AND INSTALLATION OF TRANSFER ASSEMBLY
0
3
◆ Service procedure
Installation of needle bearing
0 : Needle roller bearing installer
3 4
5
06399
cardiagn.com
7
0
5
06400
A 0
06401
24-8
MEMO
24
24-9
cardiagn.com
FRONT DRIVE
Ê3
Ù
Ê
-4
13
40
ÙÊ
33
11
31
30
28
27
- 26 36
Ê 35
20 Ê8
cardiagn.com
14 *
Ê9 38 1Ê
37 -
22 * 3
7 Ê
34
6 29
-Ê5 19 39
20 -
Ù 16 17 21 Ù
Ê15 24
27 -
18
Ê
- -
Ù
27276
● Disassembly sequence
1 Bolt 14 Interlock ball 29 Synchronizer sleeve
2 Shift rail cover 15 Lock nut 30 Front drive shift fork
3 Bolt 16 O-ring 31 Snap ring
4 Transfer case side cover 17 Companion flange 32 Front drive shift rail
5 Screw plug 18 Bolt 33 Shift rail stopper
6 Poppet spring 19 Front drive shaft 34 Snap ring
7 Steel ball 20 Snap ring 35 Front drive hub
8 Transfer LOW switch 21 Bearing 36 Snap ring
^ Gr54 22 Dust cap 37 Bolt
9 Transfer four-wheel drive 23 Oil seal 38 Front drive case
switch ^ Gr54 24 Front drive case cover 39 Oil seal
10 Screw plug 25 Set bolt 40 Transfer assembly
11 Set bolt 26 Snap ring
12 HIGH/LOW shift rail 27 Retainer * : Dowel pin
13 HIGH/LOW shift fork 28 Spring Ù : Non-reusable parts
24-10
24
NOTE
HIGH and LOW shift rail 12 cannot be disassembled unless front drive shift rail 32 is set to front drive ON.
● Assembly sequence
40→39→38→37→36→35→34→33
→ 25
32→31→30→28→27→26
29 ↑ →18→17→16→15→14→10
13→12→11
24→23→22→21→20→19 →9→8→7→6→5→4→3→2→1
cardiagn.com
12, 40 Clearance between HIGH/LOW shift rail [16 {0.63}] 0.05 to 0.09 0.2 Replace
and transfer assembly rail hole {0.0020 to 0.0035} {0.0079} faulty parts
13 Tilt of claw against HIGH/LOW shift fork hole 0.1 {0.0039} or less 0.2 {0.0079} Replace
13, 29 Clearance between HIGH/LOW shift fork 0.3 to 0.5 1.0 Replace
and synchronizer sleeve {0.012 to 0.020} {0.039} faulty parts
29, 30 Clearance between front drive shift fork 0.3 to 0.5 1.0 Replace
and synchronizer sleeve {0.012 to 0.020} {0.039} faulty parts
30 Tilt of claw against front drive shift fork hole 0.1 {0.0039} or less 0.2 Replace
{0.0079} faulty parts
32 Front drive shift rail deflection 0.02 {0.00079} or less 0.03 Correct
{0.0012} or replace
32, 40 Clearance between front drive shift rail [16 {0.63}] 0.05 to 0.09 0.2 Replace
and transfer assembly rail hole {0.0020 to 0.0035} {0.0079} faulty parts
24-11
FRONT DRIVE
- Lubricant and/or sealant
Location Points of application Specified lubricant and/or sealant Quantity
4 Mounting surface of transfer assembly transfer case side cover THREEBOND 1215 As required
5 Thread area of screw plug THREEBOND 1215 As required
10 Thread area of screw plug THREEBOND 1215 As required
18 Thread area of pierce bolt THREEBOND 1104J As required
23 Pack between lips of oil seal Wheel bearing grease [NLGI No.2 (Li soap)] As required
24 Mounting surface of front drive case front drive case cover THREEBOND 1215 As required
38 Mounting surface of transfer assembly front drive case THREEBOND 1215 As required
39 Lip area of oil seal Wheel bearing grease [NLGI No.2 (Li soap)] As required
cardiagn.com
20, 26, 34 Snap ring expander MH061268 Removal and installation of snap ring
01137
ø42
{1.65}
Bearing installer MB999104
ø52
23 {2.05} 05661 Installation of front drive case cover oil seal
ø15.5 {0.61}
ø35
{1.38} 19 {0.75} 06404
24-12
24
GU
◆ Service procedure
H\
06405
cardiagn.com
To measure the deflection of shift rails 12, 32, turn them one full
revolution and read the dial gauge indicator. The deflection is
one half of the indicated value.
H\d
01127
40 Measure the outer diameter of shift rail 12, 32 and the inner diameter of
12, 32 transfer assembly hole 40. If the clearance is higher than the limit,
replace faulty parts.
IYZ
06406
13, 30
06407
24-13
FRONT DRIVE
1
S Installation of oil seal
Apply grease to lip area A of oil seal 23, and press-fit it.
1 : Bearing installer
2 : Differential bearing inner race installer adapter
2
23
c
06409
39 0
cardiagn.com
06410
24-14
MEMO
24
24-15
cardiagn.com
IDLER GEAR AND REAR DRIVE
32 Ù 28 27 -
29
25Ê-Ù
31 Ù 30
34
32 29
26
9- 7Ê-Ù
Ê
10 11 1
12 Ù
13
4
- Ù
21
-
Ù
33
cardiagn.com
Ê
-
33
Ê
-
19
Ù-
17
16
27278
● Disassembly sequence
1 Bolt 19 Rear drive shaft HIGH gear
2 Spring pin 20 Needle bearing
3 Speedometer gear 21 Synchronizer sleeve
4 O-ring 22 Needle bearing
5 Oil seal 23 Rear drive shaft LOW gear
6 Speedometer gear bushing 24 Needle bearing
7 Bolt 25 Bolt
8 Oil seal 26 Plate
9 Output rear cover 27 Idler rear cover
10 Speedometer worm 28 Shim
11 Key 29 O-ring
12 Snap ring 30 Transfer idler shaft
13 Bearing 31 Transfer idler gear
14 Thrust washer 32 Bearing
15 Rear drive shaft 33 Drain plug, inspection plug
16 Snap ring 34 Transfer case
17 Bearing
18 Thrust washer Ù : Non-reusable parts
24-16
24
NOTE
• Check backlash and end play of gears before disassembly.
• Do not remove needle bearing 22 from rear drive shaft 15 unless it is faulty.
● Assembly sequence
31→32
34→33 →28→27→26→25
30→29 →17→16→11→10→22
15→21→24→23→14→13→12→20→19→18 →7
6→5→4→3→2
→1
9→8
NOTE
• Check backlash and end play when assembling parts.
• Check friction and rotation movements when assembling rotating parts.
cardiagn.com
Service standards Unit : mm {in.}
Standard value
Location Maintenance item (Basic diameter in [ ]) Limit Remedy
24-17
IDLER GEAR AND REAR DRIVE
- Lublicant and/or sealant
Location Points of application Specified lublicant and/or sealant Quantity
3 Friction surfaces between speedometer gear and speedometer Molybdenum disulfide grease As required
gear bushing
5 Lip area of oil seal Wheel bearing grease [NLGI No.2 (Li soap)] As required
7 Thread area of bolt THREEBOND 1104J As required
8 Pack between lips of oil seal Wheel bearing grease [NLGI No.2 (Li soap)] As required
9 Mounting surface of transfer case output rear cover THREEBOND 1215 As required
25 Thread area of bolt THREEBOND 1104J As required
27 Mounting surface of transfer case idler rear cover THREEBOND 1215 As required
33 Thread area of drain plug and inspection plug THREEBOND 1105D As required
cardiagn.com
16.5
{0.65}
8 Oil seal installer MH062691 Installation of output rear cover oil seal
06252
01137
ø40
{1.57}
24-18
24
◆ Service procedure
Inspection before service
● Starting torque of transfer idler gear
28 31
• Disassemble parts, and measure the torque with push gauge A
A
leaving only transfer idler gear 31 in transfer case.
If the value deviates from the standard value, adjust it using shim
28.
• On assembly, also check that starting torque is within the standard
value range using the same method.
• Shim 28 is available in four thicknesses : 0.01 mm {0.00039 in.},
0.02 mm {0.00079 in.}, 0.03 mm {0.0012 in.}, 0.06 mm {0.0024 in.}.
2
07633
cardiagn.com
3
6
36
03576
5
03577
A 5
6
03578
24-19
IDLER GEAR AND REAR DRIVE
6 Installation of speedometer gear bushing
Due to its eccentric center arrangement, speedometer gear bushing 6
6 allows replacement of speedometer gear 3 with gears having a different
number of teeth by changing only the installation direction, the worm
gear does not have to be changed.
M
When installing the bushing, align the stamped number, identical to the
number of speedometer gear teeth, with alignment mark M of output rear
cover 9.
The number of speedometer gear teeth can be identified by the identifi-
cation marks stamped on N or P.
Identification
mark A B C D L E F G H I J K
Number of
teeth 15 16 17 18 19 20 21 22 23 24 25 26
Gear ratio 3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2
cardiagn.com
8
06416
0 8
JN
06419
A 14, 18
06418
24-20
24
KNPST Play of rear drive shaft gear in diameter
direction after assembly
If the measured value is higher than the limit, replace faulty parts.
NOTE
When replacing needle bearing 20, 24, use bearings from the
same color package.
R
01149
cardiagn.com
06420
24-21
TRANSFER CONTROL
Control Cable < Removal from the transfer side >
● Work before removal
*b Ê Õ P24-22
Ê
1 3 ● Removal sequence
2Ê
1 Bolt
4
2 Nut
3 Nut
4 HIGH/LOW control cable
5 2H/4H control cable
6 Shift rail cover
*a : Transfer body
*b : HIGH/LOW shift rail
*c : Front drive shift rail
*a *c 1 3
6 2 5 ● Installation sequence
Ê
cardiagn.com
Ê
Ê Follow the removal sequence in reverse.
27279
◆ Service procedure
● Work before removal
A When removing, move shift lever knob A of the transfer control bar to
the position 4H.
27280
24-22
24
1
45
[Removal]
HIGH/LOW, 2H/4H Control Cable
6
1
27281
• Remove shift rail cover 6, and then remove inner cable A of HIGH/
*b, *c LOW and 2H/4H control cables 4 and 5, from HIGH/LOW shift rail *b,
*b, *c 3 2 A 3 2
and front drive shift rail *c. Loosen nuts 2 and 3 to their end of their
threads.
cardiagn.com
A 6 4, 5 6 4, 5
27282
• Remove HIGH/LOW and 2H/4H control cables 4 and 5 from shift rail
cover 6.
4
5
6 27283
B [Installation]
*b • Position HIGH/LOW shift rail *b and front drive shift rail *c as shown.
15 mm {0.59 in.} B : Transfer end face
8 mm {0.31 in.}
*c 27284
• Adjust nuts 2 and 3 to the end of the thread to align the end of HIGH/
3 2
LOW and 2H/4H control cables 4 and 5 as shown.
8±2 mm
{0.31±0.079 in.}
4, 5
27285
24-23
TRANSFER CONTROL
•Screw nut 3 into shift rail cover 6 and tighten it to the specified torque.
2 mm
{0.079 in.}
3
C CAUTION–
• Ensure that the HIGH/LOW and four-wheel / two-wheel drive
control cables are not positioned incorrectly.
The cable with the white line C is for HIGH/LOW.
• After installation, the end of nut 3 should be located 2
mm{0.079 in.} from the front face of shift rail cover 6.
6 3
27286
2 mm • Tighten the nut with its specified torque and lock it with nut 3. Then
*b, *c {0.079 in.} *b, *c slide the shift rail cover 6 and install the inner cable A to HIGH/LOW
shift rail *b and front drive shift rail *c.
cardiagn.com
6 2 A 6 2
A
27287
10±2 mm
6 {0.39±0.079 in.}
1 27288
24-24
MEMO
24
24-25
cardiagn.com
TRANSFER CONTROL
Control cable < Removal from the transfer control cable side >
● Removal Sequence
1 Nut
2 Bolt
3 Lock pin
4 Nut
5 HIGH/LOW control cable
6 Nut
7 2H/4H control cable
Ê
1
● Installation sequence
Follow the removal sequence in reverse.
3
Ê2
cardiagn.com
6Ê
6Ê
Ê4
Ê4
7
27289
24-26
24
◆ Service procedure
● Adjustment after installation
A • Position shift lever A on position 4H.
27280
• Adjust the distance between the center of the steering wheel and
245 mm {9.65 in.}
center of the shift lever knob A using the nut 6.
cardiagn.com
27290
• Adjust nut 4 until the distance between shift lever A and the front face
6.5 mm of inner panel B is equal to distance illustrated.
{0.26 in.}
A
27291
24-27
TRANSFER CONTROL
Transfer Control Level
Ê 17
22
18
21
1
Ê2 5
-8
cardiagn.com
Ê 6-
7
- 13
14
9 15
16
19 - 14
14
20 -
14 12 Ê
-
11
10 Ê
27292
● Disassembly sequence
1 Pin 9 Spring 17 Shift lever knob
2 Nut 10 Bolt 18 Change lever assembly
3 Support holder 11 Conical spring 19 Bracket
4 Spring 12 Nut 20 Bracket
5 Ball supporter 13 Collar 21 Stopper
6 Steel ball 14 Bushing 22 Lever bracket
7 Bolt 15 Cross sleeve
8 Detent plate 16 Conical spring
CAUTION–
• When removing pin 1, be careful that spring 4 does not fly out.
• When removing support holder 3, ensure that steel ball 6 is not dropped.
24-28
24
● Assembly sequence
15→14→13→11
↓
22→21→20→19 →10→12→8→7→6→5→4→3→2→1
↑
18→17→16→9
cardiagn.com
10 Bolt (Cross sleeve mounting) 8.8 to 13.7 {6.5 to 10.0, 0.9 to 1.4} —
12 Nut (Change lever assembly mounting) 8.8 to 13.7 {6.5 to 10.1, 0.9 to 1.4} —
17 Shift lever knob mounting 5.9±1.5 {4.3±1.08, 0.6±0.15} —
- Lubricant
Location Points of application Specified lubricant Quantity
6 Apply grease all over the steel ball Multipurpose type grease [NLGI No.2 (Li soap)] As required
8 Apply grease all over detent plate Multipurpose type grease [NLGI No.2 (Li soap)] As required
14 Grease inside surface of bushing Multipurpose type grease [NLGI No.2 (Li soap)] As required
24-29