RAC SK Mondal 12 PDF

Visit : www.Civildatas.
com
S K Mondal’s
Refrigeration and Air-

Conditioning
m
.co
GATE, IES & IAS 20 Years Question Answers
Contents
tas
Chapter – 1: Heat Pump and Refrigeration Cycles and
lda
Systems
Chapter - 2 : Vapour Compression System
Chapter - 3 : Refrigerants
vi
Chapter - 4 : Refrigerant Compressors

Chapter - 5 : Condensers & Evaporator
Ci
Chapter - 6 : Expansion Devices

Chapter - 7 : Gas Cycle Refrigeration
w.
Chapter - 8 : Vapour Absorption System

Chapter - 9 : Psychrometry
ww
Chapter - 10 : Miscellaneous
Er. S K Mondal
IES Officer (Railway), GATE topper, NTPC ET-2003 batch, 12 years teaching
experienced, Author of Hydro Power Familiarization (NTPC Ltd)
Page 1 of 128
Visit : www.Civildatas.com
Note
m
If you think there should be a change in
option, don’t change it by yourself send me a
.co
mail at swapan_mondal_01@yahoo.co.in
I will send you complete explanation.
tas
vi lda
Copyright © 2007 S K Mondal

Ci
w.
Every effort has been made to see that there are no errors (typographical or otherwise) in the
ww
material presented. However, it is still possible that there are a few errors (serious or
otherwise). I would be thankful to the readers if they are brought to my attention at the
following e-mail address: swapan_mondal_01@yahoo.co.in
S K Mondal
Page 2 of 128
Hea
at Pump & Refriigeration
n Cycles and Sysstems
S K Monda
M l’s Chaptter 1
1. Hea
at Pu
ump and Refrrigerration
n
Cyc
cles and Systtems
s
m
OBJECTIVE QUESTIO
U ONS (G
GATE
E, IES
S, IAS
S)
.co
Prev
vious 20-Yea
2 ars GA
ATE Qu
uestion
ns
Heat Engine,
E Heat Pump
P
GATE-1. The
T coeffiicient of performanc
p ce (COP) ofo a refrig gerator wo orking as a heat
pump
p
GATE-1. Ans.
A
is giiven by:
(a)(COP)heatt pump = (COP
(c)(COP)heat pump = (COP
(b)Th
refrigerator
r
P)refrigerator+ 2
tas
P)refrigerator – 1
(b
he COP of refrigeratoor is one leess than C

r starts workking as hea
[GATE--1995; IES--1992, 1994
b)(COP)heat ppump = (COP
(d)(COP)heat pump = (COP
COP of hea
at pump i.e. (COP)heat pum
P)refrigerator
4, 2000]
P)refrigerator+ 1
at pump, iff same

mp = (COP)reefrigerator + 1
lda
GATE-2. An
A industr rial heat pump
p operrates betw ween the te emperatures of 27°C and –
13°C. The rates of heath additiion and he eat rejectiion are 750 Wand 10
000 W,
respective
r ely. The COOP for the heat
h pump p is: [GATEE-2003]
(a) 7.5 (b) 6.5 (c) 4.0 (d) 3.0
vi
Q1 10
000
GATE-2. Ans.
A (c) (CO
OP )HP = = =4
Q1 − Q2 1000 − 750
Ci
w.
ww
GATE-3. Any
A thermmodynamic c cycle opperating between
b tw
wo temperature lim mits is
reversible
r if the pro
oduct of eff
fficiency when
w opera
ating as a heat
h engin
ne and
the
t coeffic
cient of perrformancee when opeerating as r
refrigeratiion is equa
al to 1.
Page 3 of 128
Heat Pump & Refrige

eration Cycles
C an
nd Syste
ems
S K Mo
ondal’ss Chapte
C r1
GA
ATE-3. Anss. False
Effficiency Heat engine,
⎛ TH −TL ⎞
η HEE = ⎜ ⎟⎟
⎜ TH
⎝ ⎠
TL
CO
OP of Refrige
erator =
TH − TL
m
Pro
oduct of ηHE and
OPR ≠ 1.
CO
[GATE-19
994]
.co
GA
ATE-4. Ann irreversib ble heat en ngine extra
acts heat from
fr a high
h temperatture source at
a rate
r of 100
0 kW and rejects heat to a sin W. The entire
nk at a ratte of 50 kW
woork outputt of the he eat enginee is used to drive a reversiblle heat pu ump
opeerating be etween a set of indep pendent issothermal heat reser rvoirs at 17
1 0C
GA
and
tem
d 75 C. Th
(a) 50
ATE-4. Anss. (c)
0 he rate (in kW) at wh
mperature sink is:
(b) 250 (c) 300tas
hich the heeat pump delivers
d
(d) 360
he
eat to its high
[GATE -20
h
009]
lda
Reverse
R ed Carnot Cycle
GA
ATE-5. A Carnot
C cyc
cle refriger rator opera
ates betweeen 250K a
and 300 K. Its
I coefficiient
of performan
p nce is: [GATE-19999]
(a) 6.0 (b) 5.0 (c) 1.2 (d) 0.8
T2 250
ATE-5. Anss. (b) (COP ) R =
vi
GA = =5
T1 − T2 300 − 250
0
δQ
ATE-6. In the case of
GA o a refrige rgoing an iirreversiblle cycle, φ
eration sysstem under
Ci
T
is: [GATE-19
995]
(a) < 0 (b) = 0 (c) > 0 (d) Not surre
ATE-6. Anss. (a)
GA
w.
Refriger
R ration capacity
c y (Ton o
of refrig
geration
n)
GA
ATE-7. Roound the clock
c coolling of an n apartmen nt having a load of 300 MJ//day
reqquires an air-conditi
a oning plan nt of capac city about [GATE-19
993]
ww
(a) 1 ton (b) 5 ton

ns (c) 10 ton
ns (d) 100 ton
ns
GA
ATE-7. Anss. (a) 211 kJ
J/min = 1 T refrigeratioon
300 × 103
Reffrigeration capacity
c = ≈ 1 ton
2 × 60 × 211
24 1
Prev
vious 20-Yea
2 ars IES
S Ques
stions
Heat Eng
gine, Heat Pum
mp
Page 4 of 128
Heat Pump & Refrigeration Cycles and Systems

S K Mondal’s Chapter 1
IES-1. A heat pump works on a reversed Carnot cycle. The temperature in the
condenser coils is 27°C and that in the evaporator coils is –23°C. For a work
input of 1 kW, how much is the heat pumped? [IES-2007]
(a) 1 kW (b) 5 kW (c) 6 kW (d) None of the above
Q T1 300
IES-1. Ans. (c) For heat pump (COP)HP = 1 = = or Q1 = 6 × W = 6 kW
W T1 − T2 300 − 250
IES-2. A heat pump is used to heat a house in the winter and then reversed to cool
m
the house in the summer. The inside temperature of the house is to be
maintained at 20°C. The heat transfer through the house walls is 7·9 kJ/s
and the outside temperature in winter is 5°C. What is the minimum power
(approximate) required driving the heat pump? [IES-2006]
.co
(a) 40·5 W (b) 405 W (c) 42·5 W (d) 425 W
Q T1 293 7.9 × 15
IES-2. Ans. (b) (COP )HP = 1 = = or W = kW = 405 W
W T1 − T2 15 293
IES-3. A refrigerator based on reversed Carnot cycle works between two such
be its COP?
(a) 2
T
(b) 3
IES-3. Ans. (d) 2 = 0.8 or (COP )H .P =
tas
temperatures that the ratio between the low and high temperature is 0.8. If
a heat pump is operated between same temperature range, then what would
T1
(c) 4 (d) 5
[IES-2005]
lda
=5
T1 T1 − T2
IES-4. A heat pump for domestic heating operates between a cold system at 0°C
and the hot system at 60°C. What is the minimum electric power
consumption if the heat rejected is 80000 kJ/hr? [IES-2003]
vi
(a) 2 kW (b) 3 kW (c) 4 kW (d) 5 kW

IES-4. Ans. (c) For minimum power consumption,
Q1 Q2 Q1 − Q2 W
= = =
Ci
T1 T2 T1 − T2 T1 − T2
Q1 Q2 Q1 − Q2 W
= = =
T1 T2 T1 − T2 T1 − T2
T1 − T2 80000 333 − 273
w.
W = Q1 × = × = 4 kW
T1 3600 333
IES-5. Assertion (A): If a domestic refrigerator works inside an adiabatic room

ww
with its door open, the room temperature gradually decreases.

Reason (R): Vapour compression refrigeration cycles have high COP
compared to air refrigeration cycles. [IES-2009]
(a)Both A and R are individually true and R is the correct explanation of A.
(b)Both A and R are individually true but R is not the correct explanation of A.
(c)A is true but R is false.
(d)A is false but R is true.
IES-5. Ans. (d)
IES-6. A refrigerator working on a reversed Carnot cycle has a C.O.P. of 4. If it

works as a heat pump and consumes 1 kW, the heating effect will be:
(a) 1 KW (b) 4 KW (c) 5 KW (d) 6 KW [IES-2003]
Page 5 of 128

IES-6. Ans. (c) (COP)Heat pump = (COP)refrigerator + 1 = 4 + 1 = 5

Q1 Heating effect
or (COP)Heat pump = =
W work input
or Heating effect, Q1 = W x (COP)Heat pump = 5 kW
IES-7. Assertion (A): An air-conditioner operating as a heat pump is superior to an

electric resistance heater for winter heating. [IES-2009]
m
Reason (R): A heat pump rejects more heat than the heat equivalent of the
heat absorbed.
(a)Both A and R are individually true and R is the correct explanation of A.
.co
(b)Both A and R are individually true but R is not the correct explanation of A.
(c)A is true but R is false.
(d)A is false but R is true.
IES-7. Ans. (a)
IES-8. The coefficient of performance (COP) of a refrigerator working as a heat

pump is given by:
(a)(COP)heat pump = (COP)refrigerator+ 2
(c)(COP)heat pump = (COP)refrigerator – 1 tas [IES-1992, 1994, 2000; GATE-1995]
(b) (COP)heat pump = (COP)refrigerator+ 1
(d) (COP)heat pump = (COP)refrigerator
IES-8. Ans. (b) The COP of refrigerator is one less than COP of heat pump, if same refrigerator
starts working as heat pump i.e. (COP)heat pump = (COP)refrigerator + 1
lda
IES-9. A heat pump operating on Carnot cycle pumps heat from a reservoir at 300
K to a reservoir at 600 K. The coefficient of performance is: [IES-1999]
(a) 1.5 (b) 0.5 (c) 2 (d) 1
T1 600
IES-9. Ans. (c) COP of heat pump = = =2
vi
T1 − T2 600 − 300
IES-10. The thermal efficiency of a Carnot heat engine is 30%. If the engine is
Ci
reversed in operation to work as a heat pump with operating conditions

unchanged, then what will be the COP for heat pump? [IES-2009]
(a) 0.30 (b) 2.33 (c) 3.33 (d) Cannot be calculated
IES-10. Ans. (c) Thermal Efficiency = 0.3
T T2
w.
⇒ 1 − 2 = 0.3 ⇒ = 0.7
T1 T1
T1 1 1
COP of heat pump = = = = 3.33
T1 − T2 1 − 0.7 0.3
ww
IES-11. Operating temperature of a cold storage is –2°C From the surrounding at

ambient temperature of 40 heat leaked into the cold storage is 30 kW. If the
actual COP of the plant is 1/10th of the maximum possible COP, then what
will be the power required to pump out the heat to maintain the cold
storage temperature at –2°C? [IES-2009]
(a) 1.90 kW (b) 3.70 kW (c) 20.28 kW (d) 46.50 kW
RE 1 ⎛ 271 ⎞ 30
IES-11. Ans. (d) Actual COP = ⇒ = ⇒ W = 46.50 KW
W 10 ⎜⎝ 313 − 271 ⎟⎠ W
IES-12. Assertion (A): Heat pump used for heating is a definite advancement over
the simple electric heater. [IES-1995]
Page 6 of 128

Reason (R): The heat pump is far more economical in operation than
electric heater.
(a)Both A and R are individually true and R is the correct explanation of A
(b)Both A and R are individually true but R is not the correct explanation of A
(c)A is true but R is false
(d)A is false but R is true
IES-12. Ans. (a)
IES-13. A heat pump is shown schematically as [IES-1994]
m
.co
tas
lda
IES-13. Ans. (c) In heat pump, heat is rejected to source, work done on compressor, and heat
absorbed from sink.
IES-14. A heat pump working on a reversed Carnot cycle has a C.O.P. of 5. lf it

vi
works as a refrigerator taking 1 kW of work input, the refrigerating effect

will be: [IES-1993]
(a) 1 kW (b) 2 kW (c) 2 kW (d) 4 kW
Work done
Ci
IES-14. Ans. (d) COP heat pump = or heat rejected = 5 × work done
Heat rejected
And heat rejected = refrigeration effect + work input
or, 5 × work input – work input = refrigeration effect
or, 4 × work input = refrigeration effect
w.
or refrigeration effect = 4 × 1 kW = 4 kW
IES-15. Assertion (A): The coefficient of performance of a heat pump is greater than
that for the refrigerating machine operating between the same temperature
ww
limits.[IES-2002; IAS-2002]
Reason (R): The refrigerating machine requires more energy for working
where as a heat pump requires less.
IES-15. Ans. (c) R is false. For refrigerating machine our aim is to extract heat from lower
temperature source. In heat pump we are interested on heat addition to higher
temperature side so it is heat extracted + work added. That so why it’s COP is higher
but work requirement is same for both the machine.
Page 7 of 128

IES-16. The refrigerating efficiency that is the ratio of actual COP to reversible
COP of a refrigeration cycle is 0.8, the condenser and evaporator
temperatures are 50°C and –30°C respectively. If cooling capacity of the
plant is 2.4 kW then what is the work requirement? [IES-2009]
(a) 1.00 kW (b) 1.33 kW (c) 1.25 kW (d) 2.08 kW
IES-16. Ans. (a) Condenser Temperature = 273 + 51 = 324 K
Evaporator Temperature = 273 – 30 = 243 K
243
Actual COP = 0.8 ×
m
324 − 243
∵ We know that
R.E 243 2.4
Actual COP = ⇒ 0.8 × = ⇒ W = 1.00 kW
W 324 − 243 W
.co
Reversed Carnot Cycle
IES-17. A refrigerator works on reversed Carnot cycle producing a temperature of –
40°C. Work done per TR is 700 kJ per ten minutes. What is the value of its
COP? [IES-2005]
(a) 3
IES-17. Ans. (a) W =

700
10
(b) 4.5
tas
(c) 5.8
kJ/min, Q = 210 kJ/min, COP =
210
70
=3
(d) 7.0
lda
IES-18. The coefficient of performance of a refrigerator working on a reversed
Carnot cycle is 4. The ratio of the highest absolute temperature to the
lowest absolute temperature is: [IES-1999; IAS-2003]
(a) 1.2 (b) 1.25 (c) 3.33 (d) 4
vi
T2 1
IES-18. Ans. (b) ( COP )Refrigerator of reversed Carnot cycle = = =4
T1 − T2 T1
−1
T2
Ci
T1 T1
or − 1 = 0.25 or = 1.25
T2 T2
IES-19. In an ideal refrigeration (reversed Carnot) cycle, the condenser and

w.
evaporator temperatures are 27°C and –13°C respectively. The COP of this
cycle would be: [IES-1997]
(a) 6.5 (b) 7.5 (c) 10.5 (d) 15.0
T1 ( 273 − 13 )
ww
IES-19. Ans. (a) COP = = = 6.5

T2 − T1 ( 273 + 27 ) − ( 273 − 13 )
IES-20. A refrigerating machine working on reversed Carnot cycle takes out 2 kW of

heat from the system at 200 K while working between temperature limits of
300 K and 200 K. C.O.P. and power consumed by the cycle will, respectively,
be: [IES-1997; IAS-2004]
(a) 1 and 1 kW (b) 1 and 2 kW (c) 2 and 1 kW (d) 2 and 2 kW
T2 200 Q
IES-20. Ans. (c) COP = = =2=
T1 − T2 300 − 200 W
Page 8 of 128
Hea
at Pump & Refriigeration
n Cycles and Sysstems
S K Monda
M l’s Chaptter 1
Q
Given, Q = 2 kW; ∴W = = 1 kW
2
IES-21. A Carnot refrigerattor require es 1.5 kW//ton of reffrigerationn to mainttain a

region
r at a temperatture of – 30
0°C. The CO OP of the C
Carnot reffrigerator is:
i
(a) 1.42 (b) 2.33 (c) 2.87 (d) 3.26
6 [IES
S-2003]
Q2 3.5
ns. (b) COP
IES-21. An P of carnot refrigerator
r = = = 2.33 ⎡⎣As 1 TR ≈ 3.5 kW ⎤⎦
m
W 1.5
IES-22. In
I the abo ove figure e, E is a h
heat
engine
e witth efficienncy of 0.4 a
and
.co
R is a refr
rigerator. Given
G thatt Q2
+ Q4 = 3Q 3 1 the COP of tthe
refrigerato
r or is:
(a) 2.5 (b) 3.0
(c) 4.0 (d) 5.0
[IE
ES-1992]
IES-22. An
ns. (d) For heat
And
h engine
A for refrrigerator,
tas
e, efficiency = 1 −
Q2
Q1
= 0.4
0 or Q2 = 0.6Q1
lda
W + Q = Q4 or (Q1 – Q2) + Q3 = Q4 or Q1 + Q3 = Q2 + Q4 = 3Q1
Therefore
T 2 Q 1 = Q3
Q Q3 2Q1
COP of refrigerator = 3 = = =5
W Q1 − Q2 Q1 − 0.6Q1
vi
IES-23. For
F a give
en value of TH (Sour rce temperrature) for
r a reverse
ed Carnot cycle,
the
t variattion of TL (Sink te emperature) for diffferent values of COP is
represente
r ed by whicch one of th
he followin
ng graphs?? [IES
S-2009]
Ci
w.
ww
Page 9 of 128

TL
IES-23. Ans. (c) COP =
TH − TL
COP is on y-axis and TL on x-axis
x
∴ y=
K −x
⇒ Curve (C) is the correct representation of above equation since it passes
through the origin.
m
Production of Solid Ice
IES-24. In a vapour compression refrigeration cycle for making ice, the condensing
temperature for higher COP [IES-2006]
.co
(a) Should be near the critical temperature of the refrigerant
(b) Should be above the critical temperature of the refrigerant
(c) Should be much below the critical temperature of the refrigerant
(d) Could be of any value as it does not affect the COP
IES-24. Ans. (c)
IES-25.
tas
Assertion (A): Quick freezing of food materials helps retain the original
texture of food materials and taste of juices.
which does not damage the tissue cells of food materials.

(a)
[IES-1994]
Reason (R): Quick freezing causes the formation of smaller crystals of water
Both A and R are individually true and R is the correct explanation of A

lda
(b) Both A and R are individually true but R is not the correct explanation of A
(c) A is true but R is false
(d) A is false but R is true
IES-25. Ans. (c) A is true but R is false.
vi
Refrigeration capacity (Ton of refrigeration)

IES-26. One ton refrigeration is equivalent to: [IES-1999]
(a) 3.5 kW (b) 50 kJ/s (c) l000 J/min (d) 1000 kJ/min
Ci
IES-26. Ans. (a)
IES-27. In a one ton capacity water cooler, water enters at 30°C at the rate of 200
litres per hour. The outlet temperature of water will be (sp. heat of water =
w.
4.18 kJ/kg K) [IES-2001; 2003]

(a) 3.5°C (b) 6.3°C (c) 23.7 °C (d) 15°C
IES-27. Ans. (d) 3.516 × 3600 = 4.18 × 200 × (300 − x )
or x = 14.98°C ≈ 15°C
ww
IES-28. A refrigerating machine having coefficient of performance equal to 2 is used

to remove heat at the rate of 1200 kJ/min. What is the power required for
this machine? [IES-2007]
(a) 80 kW (b) 60 kW (c) 20 kW (d) 10 kW
Q Q 1200
IES-28. Ans. (d) COP = or W = = = 10 kW
W COP 60 × 2
IES-29. A Carnot refrigerator has a COP of 6. What is the ratio of the lower to the
higher absolute temperatures? [IES-2006]
(a) 1/6 (b) 7/8 (c) 6/7 (d) 1/7
Page 10 of 128

T2 T 1 7 T2 6
IES-29. Ans. (c) (COP ) R = = 6 or 1 = 1 + = ; ∴ =
T1 − T2 T2 6 6 T1 7
IES-30. A reversed Carnot cycle working as a heat pump has a COP of 7. What is the
ratio of minimum to maximum absolute temperatures? [IES-2005]
(a) 7/8 (b) 1/6 (c) 6/7 (d) 1/7
T1 T1 − T2 1 T 6
IES-30. Ans. (c) (COP )H . P = =7 or = or 2 =
T1 − T2 T1 7 T1 7
m
IES-31. Which one of the following statements is correct? [IES-2004]
In a domestic refrigerator periodic defrosting is required because frosting
.co
(a) Causes corrosion of materials (b)Reduces heat extraction
(c) Overcools food stuff (d)Partially blocks refrigerant flow
IES-31. Ans. (b)
IES-32. Consider the following statements: [IES-1997]

In the thermoelectric refrigeration, the coefficient of performance is a
function of:
1.
2.
3.
4.
Peltier coefficient
Seebeck coefficient
tas
Electrical conductivity of materials
Temperature at cold and hot junctions

lda
5. Thermal conductivity of materials.
Of these statements:
(a) 1, 3, 4 and 5 are correct (b) 1, 2, 3 and 5 are correct
(c) 1, 2, 4 and 5 are correct (d) 2, 3, 4 and 5 are correct
IES-32. Ans. (c)
vi
IES-33. When the lower temperature is fixed, COP of a refrigerating machine can be
improved by: [IES-1992]
(a) Operating the machine at higher speeds
Ci
(b) Operating the machine at lower speeds

(c) Raising the higher temperature
(d) Lowering the higher temperature
IES-33. Ans. (d) In heat engines higher efficiency can be achieved when (T1 – T2) is higher. In
w.
refrigerating machines it is the reverse, i.e. (T1 – T2) should be lower.
IES-34. In a 0.5 TR capacity water cooler, water enters at 30°C and leaves at
15°C.What is the actual water flow rate? [IES-2005]
(a) 50 litres/hour (b) 75 litres/hour (c) 100 litres/hour (d) 125 litres/hour
ww
IES-34. Ans. (c) Q = mCP Δt or 0.5 × 12660 = m × 4.2 × ( 30 − 15 ) or m = 100 kg/hr
Previous 20-Years IAS Questions
Heat Engine, Heat Pump

IAS-1. A building in a cold climate is to be heated by a Carnot heat pump. The
minimum outside temperature is –23°C. If the building is to be kept at 27°C
and heat requirement is at the rate of 30 kW, what is the minimum power
required for heat pump? [IAS-2007]
Page 11 of 128

(a) 180 kW (b) 30 kW (c) 6 kW (d) 5 kW
Q T1 ⎛ T ⎞ ⎛ 250 ⎞
IAS-1. Ans. (d) (COP)H.P = 1 = or W = Q1 ⎜1 − 2 ⎟ = 30 × ⎜1 − ⎟ = 5 KW
W T1 − T2 ⎝ T1 ⎠ ⎝ 300 ⎠
IAS-2. In the system given above, the

temperature T = 300 K. When is the
thermodynamic efficiency σE of engine E
equal to the reciprocal of the COP of R?
m
(a) When R acts as a heat pump
(b) When R acts as a refrigerator
(c) When R acts both as a heat pump and a
refrigerator
.co
(d) When R acts as neither a heat pump nor
a refrigerator
tas [IAS-2007]
lda
300 1 1
IAS-2. Ans. (a) ηE = 1 − = = or COP = 2
600 2 COP
300 150
(COP )H . P = = 2 and (COP )R = =1
300 − 150 300 − 150
∴ R must act as a Heat pump
vi
IAS-3. Assertion (A): The coefficient of performance of a heat pump is greater than
that for the refrigerating machine operating between the same temperature
Ci
limits.[IAS-2002; IES-2002]
Reason (R): The refrigerating machine requires more energy for working
where as a heat pump requires less.
(a) Both A and R are individually true and R is the correct explanation of A
w.

IAS-3. Ans. (c) R is false. For refrigerating machine our aim is to extract heat from lower
temperature source. In heat pump we are interested on heat addition to higher
ww
temperature side so it is heat extracted + work added. That so why it’s COP is higher
but work requirement is same for both the machine.
IAS-4. In a certain ideal refrigeration cycle, the COP of heat pump is 5. The cycle
under identical condition running as heat engine will have efficiency as
(a) Zero (b) 0.20 (c) 1.00 (d) 6.00 [IAS-2001]
T1 T1 − T2 1 1
IAS-4. Ans. (b) (COP )HP = and η = = = = 0.2
T1 − T2 T1 (COP )HP 5
IAS-5. The COP of a Carnot heat pump used for heating a room at 20°C by
exchanging heat with river water at 10°C is: [IAS-1996]
(a) 0.5 (b) 2.0 (c) 28.3 (d) 29.3
Page 12 of 128

T1 293
IAS-5. Ans. (d) COP = = = 29.3
T1 − T2 293 − 283
IAS-6. Assertion (A): Although a heat pump is a refrigerating system, the coefficient of
performance differs when it is operating on the heating cycle. [IAS-1994]
Reason(R): It is condenser heat that is useful (the desired effect) instead of the
refrigerating effect.
m
IAS-6. Ans. (a)
.co
IAS-7. In a reversible cycle, the source temperature is 227°C and the sink
temperature is 27°C. The maximum available work for a heat input of 100 kJ
will be: [IAS-1995]
(a) 100 kJ (b) 60 kJ (c) 40 kJ (d) 88 kJ
Reversed Carnot Cycle

tas
IAS-7. Ans. (c) Maximum efficiency for 227° and 27°C sources =
500 − 300
500
= 0.4
Maximum work available for a heat input of 100 kJ = 0.4 × 100 = 40 kJ.
lda
IAS-8. The coefficient of performance of a refrigerator working on a reversed
Carnot cycle is 4. The ratio of the highest absolute temperature to the
lowest absolute temperature is: [IAS-2003; IES-1999]
(a) 1.2 (b) 1.25 (c) 3.33 (d) 4
T2 1
IAS-8. Ans. (b) ( COP ) Refrigerator of reversed Carnot cycle = = = 4
vi
T1 − T2 T1
−1
T2
T1 T1
Ci
or − 1 = 0.25 or = 1.25
T2 T2
IAS-9. A refrigeration system operates on the reversed Carnot cycle. The

temperature for the system is: Higher temperature = 40°C and Lower
w.
temperature = 20°C. [IAS-2007]

The capacity of the refrigeration system is 10 TR. What is the heat rejected
from the system per hour if all the losses are neglected?
(a) 1·25 kJ/hr (b) 1·55 kJ/hr (c) 2·3 kJ/hr (d) None of the above
ww
T2 293 293 Q2
IAS-9. Ans. (d) COP = = = =
T1 − T2 213 − 293 20 W
20
Q2 = 10 × 14000 KJ/hr or W = 14 × 104 × KJ/hr
293
20 ⎛ 20 ⎞
Q1 = Q2 + W = 14 × 104 + 14 × 104 × = 14 × 104 ⎜1 + KJ/hr = 150 MJ/hr
293 ⎝ 293 ⎟⎠
IAS-10. A refrigerating machine working on reversed Carnot cycle takes out 2 kW of

heat from the system at 200 K while working between temperature limits of
300 K and 200 K. COP and power consumed by the cycle will, respectively,
be: [IAS-2004; IES-1997]
Page 13 of 128

(a) 1 and 1 kW (b) 1 and 2 kW (c) 2 and 1 kW (d) 2 and 2 kW
T2 200 Q
IAS-10. Ans. (c) COP = = =2=
T1 − T2 300 − 200 W
Q
Given, Q = 2 kW; ∴ W= = 1 kW
2
IAS-11. A refrigerating machine working on reversed Carnot cycle consumes 6kW to

produce a refrigerating effect of 1000kJ/min for maintaining a region at –
m
40oC.The higher temperature (in degree centigrade) of the cycle will be:
(a) 317.88 (b) 43.88 (c) 23 (d) Zero [IAS-1997]
IAS-11. Ans. (b) COP =

Q
=
T2
or,
(1000 / 60 ) = 233
.co
W T1 − T2 6 T1 − 233
or, T1 − 233 = 83.88 or, T1 = 316.88 K = 43.88°C
IAS-12. The COP of a Carnot refrigeration cycle decreases on [IAS 1994]

(a)Decreasing the difference in operating temperatures
IAS-12. Ans. (c) COP of Carnot refrigerator

tas
(b)Keeping the upper temperature constant and increasing the lower temperature
(c)Increasing the upper temperature and keeping the lower temperature constant
(d)Increasing the upper temperature and decreasing the lower temperature
T2
T1 − T2
will decrease if upper temperature T1 is
lda
increased and T2 keeping const.
IAS-13. The efficiency of a Carnot engine is given as 0·75. If the cycle direction is
reversed, what will be the value of COP for the Carnot refrigerator?
[IAS-2002]
vi
(a) 0·27 (b) 0·33 (c) 1·27 (d) 2·33

1 1
IAS-13. Ans. (b) 1st method: (COP ) R = (COP )H .P − 1 = −1 = − 1 = 0.33
ηCarnot 0.75
Ci
T2 T 1 T2 1
2nd method: ηCarnot = 1 − = 0.75 or 2 = or = = 0.33 = (COP )R
T1 T1 4 T1 − T2 4 − 1
IAS-14. A Carnot refrigerator works between the temperatures of 200 K and 300 K.
w.
If the refrigerator receives 1 kW of heat the work requirement will be:

[IAS-2000]
(a) 0.5 kW (b) 0.67 kW (c) 1.5 kW (d) 3 kW
Q T2 1 × ( 300 − 200 )
IAS-14. Ans. (a) COP = = or, W = KW = 0.5 KW
ww
W T1 − T2 200
IAS-15. It is proposed to build refrigeration plant for a cold storage to be

maintained at – 3°C. The ambient temperature is 27°C. If 5 × 106 kJ/h of
energy is to be continuously removed from the cold storage, the MINIMUM
power required to run the refrigerator will be: [IAS-1997]
(a) 14.3 kW (b) 75.3 kW (c) 154.3 kW (d) 245.3 kW
T2 270 Q
IAS-15. Ans. (c) Maximum COP = = =9=
T1 − T2 300 − 270 Wmin
Q 5 × 106
or Wmin = = kW = 154.3 kW
9 9 × 3600
Page 14 of 128

IAS-16. If an engine of 40 percent thermal efficiency drives a refrigerator having a

coefficient of performance of 5, then the heat input to the engine for each
kJ of heat removed from the cold body of the refrigerator is:
[IAS-1996]
(a) 0.50kJ (b) 0.75kJ (c) 1.00 kJ (d) 1.25 kJ
W Q
IAS-16. Ans. (a) 0.4 = ...............(i ) and 5 = 2 ..................(ii )
Q1 W
m
Q2
∴ 0.4 Q1 = or Q1 = 0.5Q2
5
IAS-17. A reversible engine has ideal thermal efficiency of 30%. When it is used as a
.co
refrigerating machine with all other conditions unchanged, the coefficient
of performance will be: [IAS-1994, 1995]
(a) 3.33 (b) 3.00 (c) 2.33 (d) 1.33
T − T2 T
IAS-17. Ans. (c) η Carnot engine = 1 = 0.3 ⇒ 1 − 2 = 0.3
T1 T1
COP Carnot refrigerator =
Production of Solid Ice

T2
=
tas
T2
=
1 T
= 2 =
T1 − T2 0.3 T1 0.3 T1 0.3
1 7
× 0.7 = = 2.33
3
lda
IAS-18. Assertion (A): When solid CO2 (dry ice) is exposed to the atmosphere, it gets
transformed directly into vapour absorbing the latent heat of sublimation from the
surroundings. [IAS-1997]
Reason (R): The triple point of CO2 is at about 5 atmospheric pressure and at 216 K.
vi
IAS-18. Ans. (a)
Ci
Refrigeration capacity (Ton of refrigeration)

IAS-19. Assertion (A): The COP of an air-conditioning plant is lower than that of an ice
w.
plant. [IAS-1997]
Reason (R): The temperatures required in the ice plant are lower than those
required for an air-conditioning plant.
ww

IAS-19. Ans. (d) The COP of an air-conditioning plant is higher than that of an ice plant.
N
IAS-20. The power (kW) required per ton of refrigeration is , where COP is the
COP
coefficient of performance, then N is equal to: [IAS-2001]
(a) 2.75 (b) 3.50 (c) 4.75 (d) 5.25
Q Q 12660
IAS-20. Ans. (b) COP = or W = ; if W is in KW , Q = kW = 3.52 kW
W COP 3600
Page 15 of 128

IAS-21. Assertion (A):Power input per TR of a refrigeration system increases with decrease
in evaporator temperature. [IAS-2004]
Reason (R): COP of refrigeration system decreases with decrease in evaporator
temperature.
IAS-21. Ans. (a)
m
.co
tas
vi lda
Ci
w.
ww
Page 16 of 128
Va
apour Co
ompressiion Systems
S K Monda
M l’s Chaptter 2
2. Va
apour Co
ompression Syste
S em
OBJECTIVE QUESTIO
U ONS (G
GATE
E, IES
S, IAS
S)
m
Prev
vious 20-Yea
2 ars GA
ATE Qu
uestion
ns
.co
Vapour Comp
pressio
on Cycle
e
GATE-1. The
T vaapour c
compressio on
refrigerati
r ion c
cycle is
represente
r ed as sho own in the
figure
f beloow, with state
s 1 bein
ng
the
t
figure
f
exit of the evap
coordinate
c
(a) p-h
(c) p-s
is:
porator. The
e system used
u
(b)) T-s
(d)) T-h
in th
tas
his
[GATE
E-2005]
lda
GATE-1. Ans.
A (d)
vi
Ci
w.
GATE-2. In
I a vapo our compression re efrigeratioon systemm, liquid to t suction
n heat
exchanger
e r is used to o: [GATEE-2000]
(a) Keep
p the COP constant
c
(b) Prev
vent the liquuid refrigera
ant from entering the ccompressor
ww
(c) Subccool the liqu

uid refrigera
ant leaving the condensser
(d) Subccool the vappour refrigerrant from th
he evaporatoor
GATE-2. Ans.
A (c)
Data for
r Q3–Q4 are
a given
n below. Solve the problem
ms and choose
c co
orrect
answers.
A refrige
erator bassed on ide eal vapouur compre ession cycle operatees betwee en the
temperatu
t ure limits of
o –20°C annd 40°C. The refrigerrant enter
rs the cond
denser
as
a saturatted vapou ur and lea aves as saaturated lliquid. The enthalpy and
entropy
e vaalues for saturated
s liquid and
d vapour a emperatures are
at these te
given
g in th
he table be
elow:
Page 17 of 128
Vapo
our Com
mpression
n System
ms
S K Mo
ondal’ss Chapte
C r2
T(0C) Hf(kJ/kg) Hg(k
kJ/kg) sf(kJ/kgg K) sg(kJ/kg K)
K
-20 20 1
180 0.077 0.7366
40 80 2
200 0.3 0.67
GA
ATE-3. If refrigeran
r t circulation rate is 0.025 kg/s, the refrig
geration, effect
e is eq
qual
to:
(a) 2.1 kW (b) 2.5 kW
k (c) 3.0 kW
W (d) 4.0 kW
GA
ATE-3. Anss. (a) h2 = 20
00 kJ/kg
S2 = 0.67 kJ/kg g-K
m
h4 = h3 = 80 kJ J/kg
Firrst calculatin
ng quality (x)
( of vapourr
S2 = S1
.co
⇒ S2 = 0.077 + x(0.73666 – 0.07)
⇒ 0.67 = 0..07 + 0.6666 6x
Entthalpy at pooint 1, we geet
h1 = 20 + 0.90
0 (180 – 20)
= 20 + 0.90
0 × 160
GA
ATE-4. Th
h1 = 164 kJ/kg
he COP of the
t
k
refrigerator is:
tas
Reffrigerant efffect = m(h1 – h2) = 0.025(164 – 80) = 2.1 KW
[GATE-20
003]
lda
(a) 2.0 (b) 2.33 (c) 5.0 (d) 6.0
h1 − h4 1 − 80
164
ATE-4. Anss. (b) COP =
GA = =2
2.33
h2 − h1 200
2 − 164
Prev
vious 20-Yea
2 ars IES
S Ques
stions
vi
Vapour
Va C
Compre
ession Cycle
Ci
IE
ES-1. In a vapour compression refr rigeration plant, th he enthalp py valuess at
diffferent points are: [IES-20006]
(i)EEnthalpy at
a exit of thhe evapora ator = 350 kJ/kg
k
(ii))Enthalpy at exit of the
t compre essor 375 kJ/kg
k
w.
(iiii)Enthalpy
y at exit of the condenser = 225 kJ/kg
Thhe refrigeraating effic ciency of th
he plant iss 0·8. Whatt is the po
ower requiired
per r kW of coo
oling to be e producedd?
(a) 0·25 kW (b) 4·0 kW
k (c) 12·5 kW
k (d) 11 kW
ww
IE
ES-1. Ans. (a) h3 = h4
Reffrigerating effect
e (Qo)
= (h1 – h4) × ɳr
= (350 – 225) × 0.8
8
= 100 kJ/kg
k
Com
mpressor work (W)
= (h2 – h1)
= 375 – 350
= 25 kJJ/kg
Page 18 of 128
Vapour Compression Systems

W 25
The power required per kW of cooling = = kW/kW of cooling
Q 100
IES-2. The values of enthalpy at the beginning of compression, at the end of
compression and at the end of condensation are 185 kJ/kg, 210 kJ/kg and 85
kJ/kg respectively. What is the value of the COP of the vapour compression
refrigeration system? [IES-2005]
(a) 0·25 (b) 5·4 (c) 4 (d) 1·35
( h − h4 ) = (185 − 85) = 100 = 4
IES-2. Ans. (c) COP = 1
m
( h2 − h1 ) ( 210 − 185 ) 25
IES-3. For simple vapour compression cycle, enthalpy at suction = 1600 kJ/kg,
.co
enthalpy at discharge from the compressor = 1800 kJ/kg, enthalpy at exit
from condenser = 600 kJ/kg. [IES-2008]
What is the COP for this refrigeration cycle?
(a) 3·3 (b) 5·0 (c) 4 (d) 4·5
RE 1600 − 600 1000
IES-3. Ans. (b) COP of refrigeration cycle = = = =5
W 1800 − 1600 200
IES-4.
(a)
(b)
tas
Air cooling is used for freon compressors whereas water jacketing is
adopted for cooling ammonia compressors. This is because
Latent heat of ammonia is higher than that of freon
Thermal conductivity of water is higher than that of air
[IES-1997]
lda
(c) Specific heat of water is higher than that of air
(d) Of the larger superheat horn of ammonia compression cycle.
IES-4. Ans. (a)
IES-5. In a vapour compression refrigeration plant, the refrigerant leaves the

vi
evaporator at 195 kJ/kg and the condenser at 65 kJ/kg. For 1 kg/s of

refrigerant, what is the refrigeration effect? [IES-2005]
(a) 70 KW (b) 100 KW (c) 130 KW (d) 160 KW
IES-5. Ans. (c) Q = m ( h1 − h4 ) = 1 × (195 − 65 ) = 130 kW
Ci
IES-6. Consider the following statements in respect of absorption refrigeration

and vapour compression refrigeration systems: [IES-2003]
1. The former runs on low grade energy.
w.
2. The pumping work in the former is negligible since specific volume of

strong liquid solution is small.
3. The latter uses an absorber while former uses a generator.
4. The liquid pump alone replaces compressor of the latter.
ww
Which of these statements are correct?

(a) 1 and 2 (b) 1 and 3 (c) 1 and 4 (d) 2 and 4
IES-6. Ans. (a)
IES-7. A standard vapour compression refrigeration cycle consists of the following

4 thermodynamic processes in sequence: [IES-2002]
(a) Isothermal expansion, isentropic compression, isothermal compression and
isentropic expansion
(b) Constant pressure heat addition, isentropic compression, constant pressure
heat rejection and isentropic expansion
(c) Constant pressure heat addition, isentropic compression, constant pressure
heat rejection and isentropic expansion
Page 19 of 128

(d) Isothermal expansion, constant pressure heat addition, isothermal
compression and constant pressure heat rejection
IES-7. Ans. (b)
IES-8. For a heat pump working on vapour compression cycle, enthalpy values of
the working fluid at the end of heat addition process, at the end of
compression process, at the end of heat rejection process, and at the end of
isenthalpic expansion process are 195 kJ/kg, 210 kJ/kg, and 90 kJ/kg
respectively. The mass flow rate is 0.5 kg/s. Then the heating capacity of
m
heat pump is, nearly [IES-2001]
(a) 7.5 kW (b) 45 kW (c) 52.2 kW (d) 60 kW
IES-8. Ans. (d)
.co
IES-9. The enthalpies at the beginning of compression, at the end of compression
and at the end of condensation are respectively 185 kJ/kg, 210 kJ/kg and 85
kJ/kg. The COP of the vapour compression refrigeration system is:[IES-2000]
(a) 0.25 (b) 5.4 (c) 4 (d) 1.35
IES-9. Ans. (c)
IES-10.
tas
In a vapour compression plant, if certain temperature differences are to be
maintained in the evaporator and condenser in order to obtain the
necessary heat transfer, then the evaporator saturation temperature must
be: [IES-1999]
lda
(a)Higher than the derived cold-region temperature and the condenser saturation
temperature must be lower than the available cooling water temperature by
sufficient amounts
(b)Lower than the derived cold-region temperature and the condenser saturation
temperature must be lower than the available cooling water temperature by
sufficient amounts
vi
(c)Lower than the derived cold-region temperature and the condenser saturation
temperature must be higher than the available cooling water temperature by
sufficient amounts
Ci
(d)Higher than the derived cold-region temperature and the condenser saturation
temperature must be higher than the available cooling water temperature by
sufficient amounts
IES-10. Ans. (c)
w.
IES-11. The correct sequence of the given components of a vapour compression

refrigerator is: [IES-1999]
(a)Evaporator, compressor, condenser and throttle valve
(b)Condenser, throttle valve, evaporator and compressor
ww
(c)Compressor, condenser, throttle valve and evaporator

(d)Throttle valve, evaporator, compressor and condenser
IES-11. Ans. (c)

In a vapour compression system, a thermometer placed in the liquid line
can indicate whether the
1.Refrigerant flow is too low 2.Water circulation is adequate
3.Condenser is fouled 4.Pump is functioning properly
(a)1, 2 and 3 are correct (b)1, 2 and 4 are correct
(c)1, 3 and 4 are correct (d)2, 3 and 4 are correct
IES-12. Ans. (d) Thermometer in liquid line can't detect that refrigerant flow is too low.
Page 20 of 128


In the case of a vapour compression machine, if the condensing
temperature of the refrigerant is closer to the critical temperature, then
there will be:
1.Excessive power consumption
2.High compression
3.Large volume flow
m
(a)1, 2 and 3 are correct (b)1 and 2 are correct
(c)2 and 3 are correct (d)1 and 3 are correct
IES-13. Ans. (a)
.co
IES-14. A single-stage vapour compression refrigeration system cannot be used to
produce ultralow temperatures because [IES-1997]
(a)Refrigerants for ultra-low temperatures are not available
(b)Lubricants for ultra-low temperatures are not available
(c)Volumetric efficiency will decrease considerably
IES-15.
tas
(d)Heat leakage into the system will be excessive
IES-14. Ans. (c)
In a vapour compression refrigeration system, a throttle valve is used in

place of an expander because [IES-1996]
lda
(a)It considerably reduces the system weight
(b)It improves the COP, as the condenser is small
(c)The positive work in isentropic expansion of liquid is very small.
(d)It leads to significant cost reduction.
IES-15. Ans. (c) In a vapour compression refrigeration system, expander is not used because
the positive work in isentropic expansion of liquid is so small that it can't justify cost
vi
of expander. Thus a throttle valve is used in place of expander.
IES-16. Assertion (A): In vapour compression refrigeration system throttle valve is

used and not expansion cylinder. [IES-1995]
Ci
Reason (R): Throttling is a constant enthalpy process.

w.

IES-16. Ans. (b) A and R are true. But R is not right reasoning for A.
In vapour compression refrigeration system throttle valve is used and not expansion
cylinder because the power produced by expansion cylinder is very low.
ww

A decrease in evaporator temperature of a vapour compression machine
leads to:
1.An increase in refrigerating effect
2.An increase in specific volume of vapour
3.A decrease in volumetric efficiency of compressor
4.An increase in compressor work
(a)1, 3 and 4 are correct (b)1, 2 and 3 are correct
(c)2, 3 and 4 are correct (d)2 and 4 are correct.
IES-17. Ans. (c)
Page 21 of 128
Vapo
our Com
mpression
n System
ms
S K Mo
ondal’ss Chapte
C r2
IE
ES-18. In a vapour r compresssion refrig geration plant,
p the refrigeran nt leaves the
evaaporator at a 195 kJ/k kg and th he condensser at 65 kJ/kg. For r every kgg of
reffrigerant th he plant ca an supply per second d, a cooling
g load of: [IES-19
993]
(a) 70 kW (b) 100 kW
k (c) 130 kWW W
(d) 160 kW
ES-18. Ans. (c) h1 = 195
IE 5 kJ/kg and h3 = 65 kJ//kg.
Sin
nce there is no heat tran nsfer in throttling, h3 = h4
Reffrigeration effect
e = h1 – h4 = 195 – 65 = 130 kJ J/kg
ES-19.
IE Wh hich one ofo the follo owing exp pansion prrocesses ta
akes place
e in a vap
pour
m
commpression cycle? [IES-20
009]
(a)P
Polytropic process
p with
h change in temperaturre
(b)A
Adiabatic prrocess with work transsfer
.co
(c)L
Lsentropic process
p withh change in enthalpy
(d)A
Adiabatic prrocess with constant en
nthalpy
IE
ES-19. Ans. (d)
ES-20.
IE A refrigerati
r ng system m operating g on reverssed Brayto
on refriger ration cyclle is
useed for ma aintaining 250K. If the temp perature at
a the end d of consttant
IE
pre
the
essure coo oling is 300
reffrigerator is 50 K, the
3
e working substance with cp = k

(a) 250 kJ/kg (b) 200 kJ/kg
ES-20. Ans. (d) Figure shows the
k
K and
tas
d rise in the temp
en the net work of co
kJ per kg per
p °C)
(c) 50kJ/k
kg
perature of
ompressio
o air in the
on will be (assume
(
(d) 25kJ/kgg
air as
[IES-19
993]
lda
rev
versed Brayton
refrrigeration cycle.
c
Varrious vallues are
shoown.
Nett worrk of
com
mpression
vi
= (h
h2 – h1) – (h
h3 – h4)
Ci
T2 T3 300
No
ow, = or T2 = × 250 = 375
T1 T4 200
Nett work = (37
75 – 250) – (300
( – 200) = 25 and Net
N work = 25 × Cp = 25
5 kJ/kg
w.
Actual
A V
Vapour Comprression Cycle
IE
ES-21. Asssertion (A): Subcoolling of refr frigerant liiquid increases the coefficien nt of
perrformance e of refrigeration. [IES-20004]
ww
Reason (R): Subcoolin ng reducess the work k requirem ment of a refrigerattion

cyccle.
(a)B
Both A and R are indiv vidually truee and R is th he correct eexplanation of A
(b)B
Both A and R are indiv vidually truee but R is not the correect explanattion of A
(c)A
A is true but R is false
(d)A
A is false bu
ut R is true
IE
ES-21. Ans. (c) Sub coo oling ↑ Refriigerating efffect thus ↑ COP
C but ha as no effect on compreessor
worrk (Wc).
ES-22.
IE Sub-cooling with rege enerative heat
h exchanger is uused in a refrigerattion
cyc
cle. The en
nthalpies at
a condensser outlet and evapo orator outllet are 78 and
a
182
2 kJ/kg respectively
y. The enthhalpy at outlet of issentropic compresso
c or is
Page 22 of 128
Va
apour Co
ompressiion Systems
S K Monda
M l’s Chaptter 2
230 kJ/kg and enthalpy of subc
cooled liqu uid is 68 kJ
J/kg. The COP
C of the
e cycle
is: [IES
S-2002]
(a) 3.25 (b) 2.16 (c) 3.0 (d) 3.5
IES-22. An
ns. (c)
IES-23. Match
M itemms in List--I with those in List-III and Listt-III and se elect the correct
answer.
a [IES S-1996]
Listt-I List-II Listt-III
A.
A Reveersed Carno
ot engine 1 1. Condensser 6. Gen nerator
m
B.
B Subccooling 2
2. Evapora ator 7. Incrrease in
refrigerrating effectt
C. Supeerheating 3
3. Vortex refrigerator
r 8. High hest COP
.co
D.
D Consstant enthalpy 4
4. Throttlinng 9. Adia abatic
5
5. Heat puump 10. Dry compressioon
Codes: A B C D A B C D
(a) 3, 10 1, 7 2, 9 4, 6 (b) 5, 8 1, 7 2 10 4, 9
2,
(c) 4, 10 3, 8 3, 10 1, 6 (d) 2, 7 5, 8 4 6
4, 1, 9
IES-23. An
ns. (b) Reve ersed Carnoot engine iss used for heat pump and a it has highest
h COP P. Thus
for
f A, the correct cho
condenser
c
from
f
Part
P
a
and it increeases refrig
List-III and List-IIII is 1, 7.
Superheatinng occurs in
tas
oice from List-II
L and List-III is 5, 8. Sub cooling occcurs in
geration efffect. Thereffore for B, the correct choice
n evaporatoor and it iss involved iin dry comp

C in List-I, the correct chooice from Lists-II
L and
pression. Thhus for
d List-III iss 2, 10. Coonstant
lda
enthalpy
e prrocess takess place durin
ng throttling and is bassically adiab
batic processs. This
D is matcheed with 4, 9.
IES-24. The
T figu
ure given n above depicts
saturationn dome for f water
r on the
vi
temperatu
t ure-entropy y plane. W
What is the
temperatu
t ure differen nce ΔT shhown on a
typical
t iso
obar line kn nown as?
(a)Degree of wet bulb depression
d
Ci
(b)Degree of saturation n
(c)Degree off sub cooling
g
(d)Degree of reheat
w.
[IES
S-2006]
IES-24. An
ns. (c)
IES-25. The
T opera
ating tempe
erature off a cold sto
orage is – 2°C.
2 Heat le
eakage fro
om the
ww
surrounding is 30 kW
W for the a
ambient te
emperatur
re of 40°C. The actua
al COP
of
o the refr
rigeration plant used
d is one-fo
ourth that of an idea
al plant wo
orking
between
b th
he same te
emperature
es. The pow
wer requir ve the plant is:
red to driv
(a) 1.86 kW
W (b) 3.72 kW (c) 7.44
4 kW (d) 18.6
60 kW [IES
S-1994]
IES-25. An
ns. (d) COP
P of ideal pllant working between limits
l nd 40°C, i.e.. 271 and 313 K is
–2 an
T1 271
= = 6.45 , So COP
P of refrigerration plantt = 6.45/4 = 1.61
T2 − T1 31
13 − 271
Page 23 of 128
Vapo
our Com
mpression
n System
ms
S K Mo
ondal’ss Chapte
C r2
Heat ab
bstracted 30
0
OP =
CO o Work required =
or = 18.6 KW
W
Work required 61
1.6
IE
ES-26. Consider the
e following
g steps: [IES-19
994]
1. Startin
ng of comp
pressor
2. Startin
ng of coolin
ng tower pump
p
m
3. Startin
ng of chille
er water pu
ump
4. Startin
ng of blowe
er motor of
o cooling coil
c
he correct sequence
Th s o these ste
of eps in the starting of a cell air
r-condition
ning
.co
pla
ant using chilled
c watter cooling
g coil, is:
(a) 3,1,4,2 (b) 1,3,2
2,4 (c) 3,2,1,4
4 (d) 1,3,4,2
ES-26. Ans.. (c) The co
IE orrect sequ arting of a central airr conditioning plant using
uence in sta
ES-27.
IE
chilled water cooling
pum
Wh
mp, starting
c
tas
coil is starting of chiller water
w pump
p, starting of
g the comprressor, startting of bloweer motor of cooling
hich one of the following

c
o cooling toower
coil..
lda
atements is corre
sta ect with
resspect to the s
schematic
diaagram as shown abov ve?
(a) Multi-eevaporator vapour
com
mpression sy ystem of reffrigeration
(b) Two stage coompression
vi
vappour comp pression re efrigeration

sysstem
(c) Cascadde system of vapour
Ci
com
mpression re efrigeration
n system
(d) None off the above
[IES--2009]
w.
ES-27. Ans. (c)

IE
ww
A two-sta
age cascad
de refrigeration syste
em
Page 24 of 128

m
.co
A two-stage cascade refrigeration system
tas
vi lda
Ci
Two-stage vapour compression refrigeration system

w.
ww
Two-stage vapour compression refrigeration system
Page 25 of 128

Modifications in Reversed Carnot Cycle with Vapour as a

Refrigerant
IAS-1. The schematic diagram of a vapour compression refrigeration system can
be represented as [IAS-1996]
m
.co
tas
lda
IAS-1. Ans. (b)
vi
Vapour Compression Cycle

IAS-2. Replacing a water-cooled condenser with an air-cooled one in a vapour
compression refrigeration system with constant evaporator pressure results
Ci
in [IAS-2000]
(a)Increase in condensation pressure
(b)Decrease in pressure ratio
(c)Increase in pressure ratio
w.
(d)Increase in condensation temperature

IAS-2. Ans. (d) Heat transfer co-efficient of gas very small compared to water hwater >> hair. So
for same heat transfer temperature difference will be high
Q = hw A ( ΔT )w = hair A ( ΔT )air , so ( ΔT )air > ( ΔT )w
ww
IAS-3. Consider the following statements: [IAS-2007]

1.The work of compressor in vapour compression refrigeration system
increases with superheat of the suction vapour.
2.The work of compressor depends on the pressure difference rather than
the temperature difference of evaporator and condenser.
3.The coefficient of performance is within the range of 3 to 6 except at very
low temperature when it may be less than 1.
Which of the statements given above are correct?
(a) 1, 2 and 3 (b)1 and 2 only (c) 1 and 3 only (d) 2 and 3 only
IAS-3. Ans. (a)
Page 26 of 128

IAS-4. Consider the following statements pertaining to a vapour compression type
refrigerator: [IAS-2002]
1.The condenser rejects heat to the surroundings from the refrigerant.
2.The evaporator absorbs heat from the surroundings to be cooled.
3.Both the condenser and evaporator are heat exchangers with refrigerant
as a common medium.
4.The amount of heat exchanged in condenser and evaporator are equal
under steady conditions.
Which of the above statements are correct?
m
(a) 1 and 2 (b) 1, 2 and 3 (c) 1, 2 and 4 (d) 2, 3 and 4
IAS-4. Ans. (b)
.co
IAS-5. In a vapour compression cycle, the refrigerant, immediately after expansion
value is: [IAS-2002]
(a) Saturated liquid (b) Subcooled liquid
(c) Dry vapour (d) Wet vapour
IAS-5. Ans. (d) In P-h diagram it is point 4 or
'
4 both are very wet vapour.
tas
vi lda
IAS-6. Assertion (A): In a vapour compression refrigeration system, the condenser pressure
should be kept as low as possible. [IAS-1999]
Reason (R): Increase in condenser pressure reduces the refrigerating effect and
Ci
increases the work of compression.

w.

IAS-6 Ans. (a)
IAS-7. Match List-I (T-s diagram) with List-II (P-h diagrams) of vapour
compression refrigeration cycles and select the correct answer using the
ww
codes given below the lists: [IAS-1999]

List-I List-II
Page 27 of 128

m
.co
IAS-7. Ans. (b)
IAS-8.
(a)
(c)
1
4
4
1
2
3
tas3
2
(b)
(d)
1
4
4
1
3
2
2
3
Theoretical vapour compression refrigeration cycle is represented on a T-s

lda
diagram as [IAS-1997]
vi
Ci
IAS-8. Ans. (c)
IAS-9. In an ideal vapour compression refrigeration cycle, the enthalpy of the

refrigerant before and after the evaporator are respectively 75 kJ/hg and
180 kJ/kg. The circulation rate of the refrigerant for each ton of
w.
refrigeration is: [IAS-1997]

(a) 1 kg/min (b) 2 kg/min (c) 3 kg/min (d) 4 kg/min
211
IAS-9. Ans. (b) Q = m (h1 – h4) = m (180 – 75) = 211 or m = = 2 kg/min
105
ww
IAS-10. In an ideal vapour compression refrigeration cycle, the enthalpy of the

refrigerant at exit from the condenser, compressor and evaporator is 80
kJ/kg, 200 kJ/kg and 180 kJ/kg respectively. The coefficient of performance
of the cycle is: [IAS-1996]
(a) 6 (b) 5 (c) 3.5 (d) 2.5
Page 28 of 128

IAS-10. Ans. (b) h3 = h4 = 80 kJ/kg
h1 = 180 kJ/kg and
h2 = 200 kJ/kg
WC = h2 – h1
= 200 – 180 = 20 KJ/kg
Q = h1 – h4
= 180 – 80 = 100 KJ/kg
Q 100
∴ COP = = =5
Wc 20
m
IAS-11. The correct sequence of vapour compression (VC), vapour absorption (VA)
.co
and steam ejector (SE) refrigeration cycles in increasing order of the COP
is: [IAS-1995]
(a) VC, VA, SE (b) VA, SE, VC (c) SE, VC, VA (d) SE, VA, VC
IAS-11. Ans. (b) The correct sequence of VC, VA and SE in increasing order of COP is VA, SE
and VC, the Value being of the order of 0.3 to 0.4 0.5 to 0.8 and 4 to 5 respectively.
IAS-12.
below the lists:

List-I List-II
tas
Match List-I (Effect) with List-II (Process) in the case of an ideal
refrigeration cycle and select the correct answer using the codes given
[IAS-1997]
lda
A. Work input 1.Constant pressure at higher temperature
B. Heat rejection 2.Isentropic compression
C. Expansion 3.Constant temperature at lower pressure
D. Heat absorption 4.Adiabatic
(a) 4 1 2 3 (b) 2 3 4 1
vi
(c) 2 1 4 3 (d) 4 2 3 1
IAS-12. Ans. (c)
Ci
Actual Vapour Compression Cycle

IAS-13. A refrigerator storage is supplied with 3600 kg of fish at a temperature of
27°C. The fish has to be cooled to –23°C for preserving it for a long period
without deterioration. The cooling takes place in 10 hours. The specific heat
w.
of fish is 2·0 kJ/kgK above freezing point of fish and 0·5 kJ/kgK below
freezing point of fish, which is –3°C. The latent heat of freezing is 230 kJ/kg.
What is the power to drive the plant if the actual COP is half that of the
ideal COP? [IAS-2002]
ww
(a) 30 kW (b) 15 kW (c) 12 kW (d) 6 kW

1 1 T2 1 250
IAS-13. Ans. (c) (COP )actal = (COP )ideal = × = × = 2.5
2 2 T1 − T2 2 300 − 250
Total Heat transfer (Q ) = m.c pbf ( ΔT )before freeze + m.c paf ( ΔT )after freeze
= 3600[2 × 30 + 230 + 0.5 × 20]kJ = 3600 × 300 kJ
Q 3600 × 300
Rate of heat transfer =
= = 30 kW
t 10 × 3600
Q Q 30
COP = or W = = = 12 kW
W COP 2.5
Page 29 of 128

High condenser pressure in a refrigeration system can occur because
1. The water flow rate is lower than the desired value.
2. Non-condensable gases are present in the system
3. Of accumulation of lubricating oil in condenser
4. Of low charge of refrigerant in the system.
(a) 1, 3 and 4 are correct (b) 1, 2 and 3 are correct
(c) 1, 2 and 4 correct (d) 2, 3 and 4 are correct
m
IAS-14. Ans. (b)
IAS-15. Excessive pressure drop in liquid line in a refrigerating system causes
.co
[IAS-1998]
(a) High condenser pressure (b) Flashing of the liquid refrigerant
(c) Higher evaporator pressure (d) Under cooling of the liquid refrigerant
IAS-15. Ans. (b)
IAS-16. In system A vapour are superheated by 10°C in the evaporator while in
(b)
(c)
tas
system B vapour are superheated by 10°C in a liquid vapour regenerative
heat exchanger, other conditions being the same. Then
(a) COP of A = COP of B
COP of both A and B > COP of Reversed Carnot Cycle
COP of A > COP of B
[IAS-2002]
lda
(d) COP of A < COP of B
IAS-16. Ans. (a) h1′ − h1 = h3 − h3′
For regeneration as
h1′ − h4 = h1 − h4′
∴ COP is same
vi
Ci
w.
ww
Page 30 of 128
Refrigerants
3. Refrigerants
OBJECTIVE QUESTIONS (GATE, IES, IAS)
m
Previous 20-Years GATE Questions
.co
Designation of Refrigerants
GATE-1. Environment friendly refrigerant R134a is used in the new generation
domestic refrigerators. Its chemical formula is: [GATE-2004]
(a) CH ClF2 (b) C2 Cl3 F3 (c) C2 Cl2 F4 (d) C2 H2 F4
GATE-1. Ans. (d)
number of fluorine atom
R134
tas
lda
number of Hydrogen atom
(-1)
number of Carbon atom

(+1)
Hence answer is,C2H2F2

vi
Azeotropic Mixtures
Ci
GATE-2. The use of Refrigerant –22 (R-22) for temperatures below –30°C is not
recommended due to its [GATE-1993]
(a) Good miscibility with lubricating oil
(b) Poor miscibility with lubricating oil
w.
(c) Low evaporating pressure

(d) High compressor discharge temperature
GATE-2. Ans. (d)
ww
Previous 20-Years IES Questions

IES-1. A good refrigerant should have [IES-1992]
(a) Large latent heat of vaporisation and low operating pressures
(b) Small latent heat of vaporisation and high operating pressures
(c) Large latent heat of vaporisation and large operating pressures
(d) Small latent heat of vaporisation and low operating pressures
IES-1. Ans. (a)
IES-2. The desirable combination of properties for a refrigerant include

(a)High specific heat and low specific volume [IES-1998]
Page 31 of 128
Refrigerants
(b)High heat transfer coefficient and low latent heat
(c)High thermal conductivity and low freezing point
(d) High specific heat and high bailing point
IES-2. Ans. (c) Required Properties of Ideal Refrigerant:
1. The refrigerant should have low boiling point and low freezing point.
2. It must have low specific heat and high latent heat. Because high specific heat
decreases the refrigerating effect per kg of refrigerant and high latent heat at low
temperature increases the refrigerating effect per kg of refrigerant.
3. The pressures required to be maintained in the evaporator and condenser should
m
be low enough to reduce the material cost and must be positive to avoid leakage of air
into the system.
4. It must have high critical pressure and temperature to avoid large power
.co
requirements.
5. It should have low specific volume to reduce the size of the compressor.
6. It must have high thermal conductivity to reduce the area of heat transfer in
evaporator and condenser.
7. It should be non-flammable, non-explosive, non-toxic and non-corrosive.
8. It should not have any bad effects on the stored material or food, when any leak
develops in the system.
tas
9. It must have high miscibility with lubricating oil and it should not have reacting
property with lubricating oil in the temperature range of the system.
10. It should give high COP in the working temperature range. This is necessary to
reduce the running cost of the system.
lda
11. It must be readily available and it must be cheap also.
Required Properties of Ideal Refrigerant:
1. The refrigerant should have low boiling point and low freezing point.
2. It must have low specific heat and high latent heat. Because high specific heat
decreases the refrigerating effect per kg of refrigerant and high latent heat at low
vi
temperature increases the refrigerating effect per kg of refrigerant.

3. The pressures required to be maintained in the evaporator and condenser should
be low enough to reduce the material cost and must be positive to avoid leakage of air
into the system.
Ci
4. It must have high critical pressure and temperature to avoid large power
requirements.
5. It should have low specific volume to reduce the size of the compressor.
6. It must have high thermal conductivity to reduce the area of heat transfer in
w.
evaporator and condenser.

7. It should be non-flammable, non-explosive, non-toxic and non-corrosive.
8. It should not have any bad effects on the stored material or food, when any leak
develops in the system.
9. It must have high miscibility with lubricating oil and it should not have reacting
ww
properly with lubricating oil in the temperature range of the system.

10. It should give high COP in the working temperature range. This is necessary to
reduce the running cost of the system.
11. It must be readily available and it must be cheap also.
IES-3. Match List-I (Refrigerant) with List-II (Principal application) and select the
correct answer using the codes given below the lists: [IES-1995]
List-I List-II
A.Air 1.Direct contact freezing of food
B.Ammonia 2.Centrifugal compressor system
Page 32 of 128
Refrigerants
C.Carbon dioxide 3.Large industrial temperature
installation
D.Refrigerant-11 4.Automotive air-conditioners
5.Aircraft refrigeration
(a) 3 4 1 2 (b) 5 3 1 2
(c) 2 4 3 5 (d) 5 3 2 1
IES-3. Ans. (b)
m
IES-4. Which of the following statements are true for Ammonia as a refrigerant?
1.It has higher compressor discharge temperature compared to
fluorocarbons.
.co
2.It is toxic to mucous membranes.
3.It requires larger displacement per TR compared to fluorocarbons.
4.It reacts with copper and its alloys.
Select the correct answer using the codes given below: [IES-1993]
Codes: (a) 1 and 2 (b) 1, 2 and 3 (c) 1, 2 and 4 (d) 2, 3 and 4
IES-4. Ans. (c)
IES-5.
(a) Chlorine (b) Fluorine

tas
In conventional refrigerants what is the element responsible for ozone
depletion?
(c) Carbon (d) Hydrogen
[IES-2009]
IES-5. Ans. (a) Ozone Depletion Potential (ODP): According to the Montreal protocol, the
lda
ODP of refrigerants should be zero, i.e., they should be non-ozone depleting
substances. Refrigerants having non-zero ODP have either already been phased-out
(e.g. R 11, R 12) or will be phased-out in near-future(e.g. R22). Since ODP depends
mainly on the presence of chlorine or bromine in the molecules, refrigerants having
either chlorine (i.e., CFCs and HCFCs) or bromine cannot be used under the new
regulations.
vi
IES-6. Which of the following refrigerant has the maximum ozone depletion in the
stratosphere? [IES-1992]
Ci
(a) Ammonia (b) Carbon dioxide (c) Sulphur dioxide (d) Fluorine
IES-6. Ans. (d)
IES-7. Ozone depletion by CFCs occurs by breakdown of: [IES-2002]

w.
(a)Chlorine atoms from refrigerant by UV radiation and reaction with ozone in

troposphere
(b)Fluorine atoms from refrigerant by UV radiation and reaction with ozone in
troposphere
(c)Chlorine atoms from refrigerant by UV radiation and reaction with ozone in
ww
stratosphere
(d)Fluorine atoms from refrigerant by UV radiation and reaction with ozone in
stratosphere
IES-7. Ans. (c)
IES-8. Which one of the following is correct? [IES-2008]

Environmental protection agencies advise against the use of
chlorofluorocarbon refrigerants because these react with
(a)Water vapour and cause acid rain
(b)Plants and cause green house effect
(c)Oxygen and cause its depletion
(d)Ozone layer and cause its depletion
Page 33 of 128
Refrigerants
IES-8. Ans. (d)
IES-9. Consider the following statements regarding refrigerants: [IES-2000]
1. Refrigerant NH3 is used in reciprocating compressors.
2. Refrigerant CO2 is used in reciprocating compressors.
3. Refrigerant R-11 is used in centrifugal compressors.
m
(a) 1 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3
IES-9. Ans. (a)
IES-10. Match List-I (Refrigerant) with List-II (Chemical constituent) and select the
.co
List-I List-II
A.R-12 1.Trichlorotrifluroethane (CCl2FCClF2)
B.R-22 2.Difluoro monochloro methane (CHF2Cl)
C.R-717 3.Ammonia (NH3)
D.R-113
Codes:
(a)
(c)
IES-10. Ans. (b)
A
3
3
B
2
1
C
4
4
D
1
2
(b)
(d)
tas
4.Difluoro dichloro methane (CCl2F2)
A
4
4
B
2
1
C
3
3
D
1
2
lda
Secondary Refrigerants
1. Practically all common refrigerants have approximately the same COP and
power requirement.
vi
2. Ammonia mixes freely with lubricating oil and this helps lubrication of
compressors.
3. Dielectric strength of refrigerants is an important property in hermetically
sealed compressor units.
Ci
4. Leakage of ammonia can be detected by' halide torch method.

(a)1, 2 and 4 are correct (b)2 and 4 are correct
(c)1, 3 and 4 are correct (d)1 and 3 are correct
w.
IES-11. Ans. (d) Practically all refrigerants, except CO2 have fairly same COP and power
requirements. Thus statement (a) is correct. Ammonia does not mix freely with
lubricating oil. Therefore statement (b) is wrong. Dielectric strength of refrigerants is
an important property in hermetically sealed compressor units. Leakage of ammonia
ww
is detected by its odour or sulphur candle with which ammonia forms white smoke
like fumes. Thus statements 1 and 4 are correct and choice (d) is the right choice.
IES-12. In milk chilling plants, the usual secondary refrigerant is: [IES-1998]
(a)Ammonia solution (b)Sodium silicate
(c)Propylene glycol (d)Brine
IES-12. Ans. (d)
IES-13. The leakage in a Freon-based refrigeration system can be detected by using

a/an [IES-2000]
(a)Oxy-acetylene torch (b) Halide torch
(c)Sulphur torch (d) Blue litmus paper
Page 34 of 128
Refrigerants
IES-13. Ans. (b)
IES-14. Match List-I with List-II and select the correct answer [IES-1994]
List-I List-II
A. Freon 12 1. Centrifugal systems
B. Freon 22 2. Low temperature cold storage
C. Freon 11 3. Window type a/c units
D. Ammonia 4. Ice plants
m
(a) 3 2 1 4 (b) 3 1 2 4
(c) 1 2 4 3 (d) 1 3 4 2
IES-14. Ans. (a)
.co
Azeotropic Mixtures
IES-15. What is an azeotrope? [IES-2008]
(a) A non-halogenic refrigerant
(b) A refrigerant dissolved in alcohol
IES-16.
(c)
(d)
tas
A mixture of refrigerants without phase separation
An eco-friendly refrigerant
IES-15. Ans. (c) Azeotrope is a mixture of refrigerants without phase separation.
Selection of a refrigerant for a vapour – compression system depends on

lda
which among the following? [IES-2007]
(a) Toxicity (b) Environmental effect
(c) Saturation pressure – temperature relationship (d) All of the above
IES-16. Ans. (d)
IES-17. Which one of the following is the fluid whose properties in all its three
vi
phase are made use of in thermodynamics? [IES-2007]

(a) Ammonia (b) Freon 12 (c) Helium (d) Water
IES-17. Ans. (d)
Ci
IES-18. Oil separator is NOT required in refrigeration system if: [IES-2003]

(a) Refrigerant and oil are immiscible at all pressures and temperatures
(b) Refrigerant and oil are immiscible at condensation pressure and temperature
(c) Refrigerant and oil are miscible at all pressures and temperatures
w.
(d) Refrigerant and oil are miscible at condensation pressures and temperature.
IES-18. Ans. (b)

ww
In ammonia refrigeration systems, oil separator is provided because

1. Oil separation in evaporator would lead to reduction in heat transfer
coefficient.
2. Oil accumulation in the evaporator causes choking of evaporator.
3. Oil is partially miscible in the refrigerant.
4. Oil causes choking of expansion device.
(a) 1 and 2 are correct (b) 2 and 4 are correct
(c) 2, 3 and 4 are correct (d) 1, 3 and 4 are correct
IES-19. Ans. (b)

Page 35 of 128
Refrigerants
Moisture should be removed from refrigerants to avoid
1. Compressor seal failure 2. Freezing at the expansion valve
3. Restriction to refrigerant flow 4. Corrosion of steel parts
(a) 1, 2, 3 and 4 are correct (b) 1 and 2 are correct
(c) 2, 3 and 4 are correct (d) 1, 3 and 4 are correct.
IES-20. Ans. (a) All the statements about effect of moisture on refrigerant are correct.
IES-21. The leaks in a refrigeration system freon are detected by: [IES-2006]
m
(a) A halide torch, which on detecting produces greenish flame lighting
(b) Sulphur sticks, which on detecting give white smoke
(c) Using reagents
.co
(d) Sensing reduction in pressures
IES-21. Ans. (a) Several methods are available for the detection of leaks. The most common is
the soap-bubble method. The other is the halide torch method used with
fluorocarbons.
IAS-1.
tas
Assertion (A): R-22 is used as a refrigerant in all refrigerators.
Reason (R): R-22 is non-toxic and non-inflammable.
lda
IAS-1. Ans. (d)
vi
IAS-2. Match List-I (Chemical formula of refrigerant) with List-II (Numerical
Designation) and select the correct answer using the codes given below the
Ci
lists: [IAS-2002]
List-I List-II
A. NH3 1.12
B. CCl2F2 2.22
w.
C. CHClF2 3.40
D. CCl2 FCCl F2 4.113
5.717
(a) 4 1 5 2 (b) 5 3 2 4
ww
(c) 4 3 5 2 (d) 5 1 2 4
IAS-2. Ans. (d) R(C – 1)(H + 1)F and Cl by balance and for inorganic refrigerant R(700 +
Molecular weight).
IAS-3. Match List-I with List-II and select the correct answer using the codes given
below the lists: [IAS-2001]
List-I List-II
A. Refrigerant 11 1.CC12F2
B. Refrigerant 12 2.C2Cl2F4
C. Refrigerant 22 3.CCl3F
D. Refrigerant 114 4.CHClF2
Page 36 of 128
Refrigerants
5.CH2ClF
(a) 2 1 5 3 (b) 3 4 5 2
(c) 3 1 4 2 (d) 5 1 4 3
IAS-3. Ans. (c) R (C − 1 )( H + 1 ) F
∴ R11 = R011 ⇒ C = 1, H = 0, F = 1, Cl = 3
∴ R12 = R012 ⇒ C = 1, H = 0, F = 2, Cl = 2
∴ R22 = R022 ⇒ C = 1, H = 1, F = 2, Cl = 1
m
∴ R114 = R114 ⇒ C = 2, H = 0, F = 4, Cl = 2
IAS-4. The refrigerant – 12 (R – 12) used in vapour compression refrigeration
.co
system is: [IAS-2000]
(a) CHCIF2 (b) CCl2F2 (c) CHCl2F (d) CCIF3
IAS-4. Ans. (b) R12 = R012 = R(C – 1)(H + 1)F. Therefore C = 1, H = 0, F = 2 by balance Cl = 2
IAS-5. Match List-I (Refrigerant) with List-II (Designation) and select the correct
answer using the codes given below the lists: [IAS-1999]
B.Water
List-I
A.Dichlorodifluoromethane
C.Methyl chloride
D.Monochloride-fluoromethane
tas
List-II
1.R 718
2.R 22
3.R40
4.R 12
lda
(a) 4 1 2 3 (b) 1 4 3 2
(c) 1 4 2 3 (d) 4 1 3 2
IAS-5. Ans. (d)
vi
Secondary Refrigerants
IAS-6. Assertion (A): Freon-12 is odourless and its leakage cannot be easily
detected. However, it is preferred in comfort air-conditioning. [IAS 1994]
Ci
Reason (R): It is almost impossible for Freon-12 leakage to attain a fatal

concentration.
w.

IAS-6. Ans. (a)
IAS-7. The pipes and fitting in an ammonia refrigeration system should be made
ww
of: [IAS-1998]
(a)Cast steel or wrought iron (b) Aluminium
(c)Naval brass (d) Copper
IAS-7. Ans. (a)
Azeotropic Mixtures
IAS-8. Match List-I with List-II and select the correct answer using the codes given
List-I List-II
A.Sulphur candle test 1.Propane
B.Halide torch test 2.Ammonia
Page 37 of 128
Refrigerants
C.Soap and water test 3.Halocarbon refrigerants
D.Ammonia swab test 4.Sulphur dioxide
(a) 2 3 1 4 (b) 4 1 3 2
(c) 2 1 3 4 (d) 4 3 1 2
IAS-8. Ans. (a)

1.In Freon 22 system, moisture chocking generally does not occur.
m
2.Freon 11 is mainly used in large capacity air-conditioning plants with
centrifugal compressor.
3.Pressure of lubricating oil in evaporator will increase the heat transfer
.co
coefficient.
4.Refrigerants that are completely miscible with oil, do not cause oil
chocking.
(a)1, 2 and 3 are correct (b)1, 2 and 3 correct
(c)2, 3 and 4 correct (d)1, 3 and 4 are correct
IAS-9. Ans. (c)
IAS-10. Which one of the following

temperature?
(a) Water (b) Carbon dioxide
tasrefrigerants
(c) Freon 12
has the highest critical
(d) Ammonia
[IAS-1996]
lda
IAS-10. Ans. (a)
IAS-11. The significant advantage of using ammonia as a refrigerant is its

(a)Characteristic odour (b)High latent heat [IAS-1996]
(c)Solubility (d)Inflammability
IAS-11. Ans. (b)
vi
IAS-12. The color of the flame of halide torch, in a case of leakage of Freon
refrigerant, will change to: [IAS-1996]
Ci
(a) Bright green (b) Yellow (c) Red (d) Orange

IAS-12. Ans. (a)
w.
IAS-13. Ideal refrigeration mixture is one which [IAS-2007]

(a)Obeys Raoult's law in liquid phase and does not obey Dalton's law in vapour phase
(b)Does not obey Raoult's law in liquid phase and does not obey Dalton's law in
vapour phase
ww
(c)Obeys Raoult's law in liquid phase and obeys Dalton's law in vapour phase
(d)Does not obey Raoult's law in liquid phase and obeys Dalton's law in vapour phase
IAS-13. Ans. (c)
Page 38 of 128
Refrigerant Compressors
4. Refrigerant Compressors
m
.co
Types of Compressors
GATE-1. p–v diagram has been obtained from a test on a reciprocating compressor.
Which of the following represents that diagram? [GATE-2005]
(a)
tas (b)
lda
(c) (d)
vi
Ci
GATE-1. Ans. (d) It is obtained from a test, so pout will be some less than compressor outlet
pressure for opening the delivery valve.
w.
GATE-2. A single-acting two-stage compressor with complete inter cooling delivers

air at 16 bar. Assuming an intake state of 1 bar at 15°C, the pressure ratio
per stage is: [GATE-2001]
(a) 16 (b) 8 (c) 4 (d) 2
ww
GATE-2. Ans. (c) Pressure ratio of each stage must be same

p p pi × p2 p2
rp = i = 2 = = = 16 = 4
p1 pi p1 × pi p1
GATE-3. Air (Cp = 1 kJ/kg, γ = 1.4) enters a compressor at a temperature of 27°C. The
compressor pressure ratio is 4. Assuming an efficiency of 80%, the
compressor work required in kJ/kg is: [GATE-1998]
(a)160 (b)172 (c)182 (d)225
Page 39 of 128
γ −1 γ −1
⎡ ⎤ ⎡ ⎤
γ RT1 ⎢⎛ p2 ⎞ γ ⎛ p2 ⎞ γ ⎡ 1.4 −1 ⎤
GATE-3. Ans. (c) Wideal = ⎜ ⎟ − 1 = c p T1 ⎜ ⎟ − 1⎥ = 1× 300 ⎢ 4 1.4 − 1⎥ = 146kJ / kg
⎥ ⎢
γ − 1 ⎢⎝ p1 ⎠ ⎥ ⎢ p
⎝ 1⎠
⎥
⎣ ⎦
⎣⎢ ⎥⎦ ⎣⎢ ⎦⎥
Wideal 146
Wactual = = = 182kJ / kg
η 0.8
GATE-4. Consider a two stage reciprocating air compressor with a perfect

intercooler operating at the best intermediate pressure. Air enters the low
m
pressure cylinder at 1bar, 27°C and leaves the high pressure cylinder at 9
bar. Assume the index of compression and expansion in each stage is 1.4 and
that for air R = 286.7 J/kg K, the work done per kg air in the high pressure
cylinder is: [GATE-1997]
.co
(a) 111 kJ (b) 222 kJ (c) 37 kJ (d) 74 kJ
GATE-4. Ans. (a) Pressure ratio must be same
Pi P2 Pi × P2 P2 9
∴ rP = = = = = =3
P1 Pi P1 × Pi P1 1
Work done of each stage also same
Weach stage =
γ RT1 ⎡
⎢r
γ − 1 ⎢⎣ P
γ −1
γ
⎥⎦ (1.4 − 1) ⎢⎣
GATE-5. A refrigeration compressor designed to operate with R 22……….

tas
⎤ 1.4 × 287 × 300 ⎡ 1.4 −1 ⎤
− 1⎥ = 3 1.4 − 1⎥ = 111 kJ
⎦
lda
(can/cannot) be operated with R 12 because the condensing pressure of R22
at any give temperature is……..(higher/lower) than that of R 12. [GATE-1992]
(a) Cannot; Higher (b) Can; Higher

(c) Cannot; Lower (d) Can; Lower
GATE-5. Ans. (a)
vi
GATE-6. Select statements from List-II matching the processes in List-I. Enter your
answer as A, B if the correct choice for (1) is (A) and that for (2) is (B)
Ci
List-I List-II [GATE-1999]

1. Inter-cooling A. No heat transfer during compression
2. Isothermal compression B. Reduces low pressure compressor work
C. Heat rejection during compression
D. Reduces high pressure compressor work
w.
GATE-6. Ans. (c, d)
Volumetric Efficiency of reciprocating Compressors

ww
GATE-7. Which of the following statements does NOT apply to the volumetric
efficiency of a reciprocating air compressor? [GATE-1999]
(a)It decreases with increase in inlet temperature
(b)It increases with decrease in pressure ratio
(c)It increases with decrease in clearance ratio
(d)It decreases with increase in clearance to stroke ratio
GATE-7. Ans. (a)
Page 40 of 128
Refriger
rant Com
mpressor
rs
S K Monda
M l’s Chaptter 4
Effect of Clea
arance on
o Worrk
GATE-8. Clearance volume of a recipro ocating compressor is 100 ml, and the volumev
o the cylinder at bo
of ottom dead d centre iss 1.0 litre. T
The cleara ance ratio of the
compresso
c or is: [GATE E-1997]
1 1 1 1
(a) (b) (c) (d)
11 10
0 9 12
GATE-8. Ans.
A (c) Pistton displaceement volumme = 900 mll
Clerance voolume 100 1
m
Therefore
T cllearance rattio = = =
Piston
n displacemment volumee 900 9
GATE-9. A R-12 refr

frigerant re eciprocatinng
.co
compresso
c or operates between
the
t condeensing tem mperature of
30°C and evaporattor
temperatu
t ure of – 20°C. The
clearance
c volume ratio
r of the
compresso
c
ratio
r
the
t
Other
O
or is 0.03. Specific
of thhe vapour
speciific volum
suction is 0.1089 m3/k
prop
S he
me at the
kg.
perties at various
v
eat
r is 1.15 an
nd
tas
lda
[GATEE-2004]
states are given in the t figure. To realize e 2 Tons oof refrigera
ation, the actual
volume
v dis
splacemen nt rate conssidering th he effect off clearance
e is:
(a) 6.35 × 10
0-3 m3/s (b) 63.5 × 10-3 m3/s (c) 635 × 10-3 m3/s ( 4.88 × 10
(d) 0-3 m3/s
GATE-9. Ans.
A (a) Givven, Clearan nce volume ration, C = 0.03
vi
Speccific volume at suction, v1 = 0.10899 m3/kg

Net refrigeratinng effect = 2 ton = 2 × 3.516 kJ = 7.032 kJ/s
Speccific heat ratio, c = 1.15
5
∴ Volu
ume = 0.063 × 0.1089 = 6.89 × 10–3 m3/s
Ci
1
⎛p ⎞ ⎛ 7.45 ⎞1.15
umetric efficciency = 1 + C – C ⎜ 2 ⎟ ve = 1 + 0.03 − 0.03 ⎜
Volu ⎟ = 0.909
⎝ p1 ⎠ ⎝ 1.50 ⎠
∴ Volu
ume displaceement rate considering g effect of cleearance
w.
= 6.8
89 × 10–3 × 0.909
0 = 6.266 × 10–3 m3/ss
Centriffugal Compres
C ssors
GATE-10. The
T speciffic speed of a centrifu ugal compressor is g generally [GATEE-1997]
ww
(a)Higher thhan that of an axial commpressor

(b)Less thann that of a reciprocatin
r ng compressor
(c)Independdent of the e type of compressor, but depen n the size of the
nds only on
compressor
c
(d)More thaan the specific speed oof the reciprrocating com
mpressor bu
ut less thatt of the
axial
a comprressor
GATE-10. Ans. (d)
Page 41 of 128
Performance Characteristics of Centrifugal Compressors
GATE-11. Air (Cp = 1 KJ, γ = 1.4) enters a compressor at a temperature of 27°C, the
compressor pressure ratio is 4. Assuming an efficiency of 80%, the
compressor work required in KJ/Kg is: [GATE-1998]
(a) 160 (b) 172 (c) 182 (d) 225
⎡ (γ −1) ⎤
γ γ ⎢ P2 γ
⎛ ⎞ ⎥
GATE-11. Ans. (c) Wideal = (P1V1 – P2V2) = P1V1 ⎢⎜ ⎟⎟ − 1⎥
⎜
γ −1 γ −1 ⎢⎝ P 1 ⎠ ⎥
m
⎣ ⎦
⎡ ( γ −1)
⎤ ⎡ ( γ −1)
⎤
γ ⎢⎛ P 2 ⎞ γ ⎥ ⎢⎛ P 2 ⎞ γ ⎥
= RT1 ⎢⎜ ⎟⎟ − 1⎥ = CpT1 ⎢⎜ ⎟⎟ − 1⎥ = 1 × 300[40.4/1.4-1] = 146
⎜ ⎜
⎢⎝ P 1 ⎠ ⎢⎝ P 1 ⎠
.co
γ −1 ⎥ ⎥
⎣ ⎦ ⎣ ⎦
146
∴ Wactual = W ideal = = 182
η 0.8
tas
lda
IES-1. A centrifugal compressor is suitable for which of the following? ` [IES-2008]
(a) High pressure ratio, low mass flow
(b) Low pressure ratio, low mass flow
(c) High pressure ratio, high mass flow
(d) Low pressure ratio, high mass flow
IES-1. Ans. (d)
vi
IES-2. Match List-I (Name of equipment) with List-II (Pressure ratio) and select
the correct answer using the code given below the lists: [IES-2007]
Ci
List-I List-II
A. Fan 1.1.1
B. Blower 2.2.5
C. Centrifugal air compressor 3.4
D. Axial flow air compressor 4.10
w.
(a) 2 1 3 4 (b) 1 2 3 4
(c) 1 2 4 3 (d) 2 1 4 3
IES-2. Ans. (b)
ww
IES-3. Which of the following can be the cause/causes of an air-cooled compressor

getting overheated during operation? [IES-2006]
1.Insufficient lubricating oil.
2.Broken valve strip.
3.Clogged intake filter.
Select the correct answer using the code given below:
(a) Only 3 (b) Only 1 and 2 (c) Only 2 and 3 (d) 1, 2 and 3
IES-3. Ans. (d)
IES-4. Which type of valves is generally used in reciprocating refrigerant

compressors? [IES-2006]
Page 42 of 128
(a) Mushroom valve (b) Puppet valve
(c) Plate valve (d) Throttle valve
IES-4. Ans. (c)
IES-5. Reciprocating compressors are provided with [IES-2000]
(a) Simple disc/plate valve (b) Poppet valve
(c) Spring-loaded disc valve (d) Solenoid valve
IES-5. Ans. (a)
m
In reciprocating compressors, one should aim at compressing the air
(a) Adiabatically (b) Isentropically (c) Isothermally (d) Poly tropically
IES-6. Ans. (c)
.co
IES-7. Roots blower is an example of: [IES-2003]
(a) Reciprocating (positive displacement) compressor
(b) Rotary (positive displacement) compressor
(c) Centrifugal compressor
(d) Axial compressor
IES-7. Ans. (b)
IES-8.
select the correct answer:
List-I
tas
Match List-I (Refrigeration equipment) with List-II (Characteristic) and
List-II
[IES-2002]
lda
A. Hermetically sealed compressor 1. Capillary tube
B. Semi-hermitically sealed 2. Both compressor and motor enclosed
Compressor in a shell or casting
C. Open type compressor 3. Both compressor and motor enclosed
in a shell or casing with a removable
cylinder cover
vi
D. Expansion device 4. Driving motor of enclosed in a shell

or casing and connected to the shaft
driving
Ci
(a) 1 4 3 2 (b) 2 3 4 1
(c) 1 3 4 2 (d) 2 4 3 1
IES-8. Ans. (b)
w.
IES-9. The capacity of an air compressor is specified as 3 m3/min. It means that the
compressor is capable of: [IES-2000]
(a) Supplying 3 m3 of compressed air per minute
(b) Compressing 3 m3 of free air per minute
ww
(c) Supplying 3 m3 of compressed air at NTP

(d) Compressing 3 m3 of standard air per minute
IES-9. Ans. (b)
IES-10. Which one of the following pairs of features and compressors type is NOT
correctly matched? [IES-2000]
(a) Intake and delivery ports : Vane compressor back flow and internal
compression is attained by compression cylindrical rotor
set to eccentric casing
(b) Intermittent discharge : Reciprocating compressor pressure, slow
requires receiver, produces high speed and lubrication
(c) Continuous flow, radial now, problems
Page 43 of 128
handles large volume :
Centrifugal compressor much higher
(d) Successive pressure drops speed and fitted into design of
through contracting : aero-engine
Axial flow compressor passages, blades
are formed from a number of
circular arcs, axial now
IES-10. Ans. (c)
m
IES-11. When a burnt out hermetic compressor is replaced by a new one, it is
desirable to include in the system a large drier-cum ·strainer also. This is to
.co
be placed in [IES-1999]
(a) Liquid line (b) Suction line (c) Hot gas line (d) Discharge line
IES-11. Ans. (d)
IES-12. Assertion (A): A reciprocating air compressor at sea level would deliver a
greater mass of air than a compressor on a mountain. [IES-1998]
(a)
(b)
(c)
(d)
tas
Reason (R): The compressor ratings are given for “free air”.
Both A and R are individually true and R is the correct explanation of A
Both A and R are individually true but R is not the correct explanation of A
A is true but R is false
A is false but R is true
lda
IES-12. Ans. (b)
IES-13. What is the preferred intercooler pressure for a two stage air compressor
working between the suction pressure ps and the delivery pressure pd?
(a) (ps + pd)/2 (b) (ps + pd)/2 (c) (ps x pd)1/2 (d) (ps + pd)1/4 [IES-2006]
IES-13. Ans. (c)
vi
IES-14. When are shock waves formed in air compressors? [IES-2006]

(a) Mach number < 0.9
Ci
(b) Mach number > 0·9

(c) Mach number = 2
(d) Mach number changes suddenly from one value to another
IES-14. Ans. (b)
w.
IES-15. Assertion (A): In multi-stage compressors, the polytropic efficiency is

always greater than the isentropic efficiency. [IES-2005]
Reason(R): Higher the pressure ration, the greater is the polytropic
efficiency.
ww
IES-15. Ans. (b)
IES-16. For a two-stage reciprocating air compressor, the suction pressure is 1.5 bar
and the delivery pressure is 54 bar. What is the value of the ideal
intercooler pressure? [IES-2004]
(a) 6 bar (b) 9 bar (c) 27.75 bar (d) 9/ 2 bar
IES-16. Ans. (b) Pi = P1 P2 = 54 × 1.5 = 9 bar
Page 44 of 128
IES-17. During steady flow compression process of a gas with mass flow rate of 2
kg/s. increase in specific enthalpy is 15kJ/kg and decrease in kinetic energy
is 2 kJ/kg. The rate of heat rejection to the environment is 3kW. The power
needed to drive the compressor is: [IES-2003]
(a) 23 kW (b) 26kW (c) 29kW (d) 37 kW
IES-17. Ans. (c) Power needed to drive the compression
v2 v2
Using, S.F.E.E., we get: h1 + 1 + Q = h2 + 2 + W
2 2
m
W = – 3 – 30 + 4 = – 29 Kw
IES-18. 0.70 kg/s of air enters with a specific enthalpy of 290 kJ and leaves it with
.co
450 kJ of specific enthalpy. Velocities at inlet and exit are 6 m/s and 2 m/s
respectively. Assuming adiabatic process, what is power input to the
compressor? [IES-2009]
(a) 120 kW (b) 118 kW (c) 115kW (d) 112 kW
⎡⎛ V2 ⎞ ⎛ V 2 ⎞⎤
IES-18. Ans. (d) Power input to compressor = m ⎢⎜ h2 + 2 ⎟ − ⎜ h2 + 1 ⎟ ⎥
⎣⎢⎝ 2g ⎠ ⎝
⎡⎛
tas
= 0.7 ⎢⎜ 450 +
⎢⎣⎝
2 g ⎠ ⎦⎥
22 ⎞ ⎛
⎟ − ⎜ 290 +
2 × 9.8 ×100 ⎠ ⎝
62 ⎞⎤
⎟ ⎥ = 112 kW
2 × 9.8 ×1000 ⎠ ⎥⎦
lda
IES-19. In a two-stage compressor with ideal intercooling, for the work requirement
to be minimum, the intermediate pressure Pi in terms of condenser and
evaporator pressure pc and pe respectively is: [IES-2003]
(a) pi = pc pe (b) pi = pc pe (c) pi = pc / pe (d) pi = pc / pe
IES-19. Ans. (b)
vi
IES-20. When a refrigerator system is started from ambient conditions, the

evaporator temperature decreases from ambient temperature to design
value. This period is known as a pull-down period. The power requirement
Ci
of compressor during pull-down [IES-2003]

(a) Decreases continuously (b) Increases continuously
(c) Remains constant (d) Increases and then decreases
IES-20. Ans. (b)
w.
p
IES-21. If n is the polytropic index of compression and 2 is the pressure ratio for a
p1
three-stage compressor with ideal inter-cooling, the expression for the total
work of three stage is: [IES-2001]
ww
⎧ ( n −1) ⎫ ⎧ ( n −1) ⎫
3n ⎪⎛ p2 ⎞ n
⎪ n ⎪⎛ p2 ⎞ 3n
⎪
(a) p1v1 ⎨⎜ ⎟ − 1⎬ (b) p1v1 ⎨⎜ ⎟ − 1⎬
( n − 1) ⎪⎝ p1 ⎠ ⎪ ( n − 1) ⎪⎝ p1 ⎠ ⎪
⎩ ⎭ ⎩ ⎭
⎧ ( n −1) ⎫ ⎧ ( n −1) ⎫
n ⎪⎛ p2 ⎞ n
⎪ 3n ⎪⎛ p2 ⎞ 3n
⎪
(c) p1v1 ⎨⎜ ⎟ − 1⎬ (d) p1v1 ⎨⎜ ⎟ − 1⎬
( n − 1) ⎪⎝ p1 ⎠ ⎪ ( n − 1) ⎪⎝ p1 ⎠ ⎪
⎩ ⎭ ⎩ ⎭
IES-21. Ans. (d)
Page 45 of 128
IES-22. The air with enthalpy of 100kJ/kg is compressed by an air compressor to a
pressure and temperature at which its enthalpy becomes 200kJ/kg. The loss
of heat is 40 kJ/kg from the compressor as· the air passes through it.
Neglecting kinetic and potential energies, the power required for an air
mass flow of 0.5kg/s is: [IES-2000]
(a) 30kW (b) 50kW (c) 70 kW (d) 90 kW
IES-22. Ans. (c)
IES-23. Two-stage compressors takes in air at 1.1 bar and discharges at 20 bar. For
m
maximum efficiency, the intermediate pressure is: [IES-2000]
(a) 10.55 bar (b) 7.33 bar (c) 5.5 bar (d) 4.7 bar
IES-23. Ans. (d). We know that for minimum compressor work pressure ratio of both stages
.co
P1 P
must be same so = i or Pi = P1 P2 = 1.1 × 20 = √22 = 4.7 bar
Pi P2
IES-24. The discharge pressure of the compressor in the refrigeration system goes
up due to the [IES-2000]
(c) Large size of the condenser

(d) Undercharge of the refrigerant
IES-24. Ans. (a)
tas
(a) Lower volumetric efficiency of the compressor
(b) Formation of scale in the condenser
lda
IES-25. A 3-stage reciprocating compressor has suction pressure of 1 bar and
delivery pressure of 27 bar. For minimum work of compression, the delivery
pressure of 1st stage is: [IES-1999]
(a) 14 bar (b) 9 bar (c) 5.196 bar (d) 3bar
IES-25. Ans. (d) For minimum work of compression in 3 stage compressor the delivery pressure
vi
of 1st stage is 3 27/1=3 bar = 3 bar
IES-26. Which one of the following statements is true? [IES-1998]

Ci
(a) In a multi-stage compressor, adiabatic efficiency is less than stage efficiency

(b) In a multi-stage turbine, adiabatic efficiency is less than the stage efficiency
(c) Preheat factor for a multi-stage compressor is greater than one
(d) Preheat factor does not affect the multi-stage compressor performance
w.
IES-26. Ans. (c)
IES-27. The heat rejection by a

reciprocating air compressor
during the reversible
ww
compression process AB, shown

in the following temperature-
entropy diagram, is represented
by the area:
(a) ABC (b) ABDE
(c) ABFG (d) ABFOE
[IES-1997]
IES-27. Ans. (b) Heat rejection during AB is given by area below it on entropy axis, i.e. ABDE.
DES
IES-28. For a multistage compressor, the polytropic efficiency is: [IES-1996]

Page 46 of 128
(a) The efficiency of all stages combined together
(b) The efficiency of one stage
(c) Constant throughout for all the stages
(d) A direct consequence of the pressure ratio
IES-28. Ans. (a) For multistage compressor, the polytropic efficiency is the efficiency of all
stages combined together.
IES-29. Phenomenon of choking in compressor means [IES-1996]

(a) No flow of air.
m
(b) Fixed mass flow rate regardless of pressure ratio.
(c) Reducing mass flow rate with increase in pressure ratio.
(d) Increased inclination of chord with air stream.
.co
IES-29. Ans. (b) Phenomenon of choking in compressor means fixed mass flow rate regardless
of pressure ratio.
IES-30. The usual assumption in elementary compressor cascade theory is that

(a) Axial velocity through the cascade changes. [IES-1996]
(b) For elementary compressor cascade theory, the pressure rise across the cascade is
given by equation of state
tas
(c) Axial velocity through the cascade does not change.
(d) With no change in axial velocity between inlet and outlet, the velocity diagram is
formed.
IES-30. Ans. (c) The usual assumption in elementary compressor cascade theory is that axial
lda
velocity thr6ugh the cascade does not change.
IES-31. In a reciprocating air compressor the compression works per kg of air.

(a) Increases as clearance volume increases [IES-1995]
(b) Decreases as clearance volume increases
(c) Is independent of clearance volume
vi
(d) Increases with clearance volume only for multistage compressor.

IES-31. Ans. (a) Compression work per kg. of air increases as clearance volume increases.
Ci
IES-32. Assertion (A): The isothermal efficiency of a reciprocating compressor becomes

100% if perfect cooling of the fluid during compression is attained. [IES-1993]
Reason (R): Work done in a reciprocating compressor is less if the process of
compression is isothermal rather than polytropic.
w.
IES-32. Ans. (a) Both assertion and reason are correct and R provides correct explanation for
ww
A.

1. Reciprocating compressors are best suited for high pressure and low
volume capacity.
2. The effect of clearance volume on power consumption is negligible for
the same volume of discharge
3. While the compressor is idling, the delivery valve is kept open by the
control circuit.
4. Inter-cooling of air between the stages of compression helps to minimize
losses.
Page 47 of 128
(c) 2 and 4 are correct (d) 3 alone is correct
IES-33. Ans. (b)
IES-34. For two stage compressor in which index of compression for low pressure
stage is m and for high pressure stage in n. The load shearing with perfect
inter-cooling is expressed as: [IES-1992]
W1 m ( n − 1) W1 n ( n − 1) W1 n W1 m
(a ) = (b) = (c ) = (d ) =
W2 n ( m − 1) W2 m ( m − 1)
m
W2 m W2 n
IES-34. Ans. (a)
IES-35. The suction pressure is 1 bar and delivery pressure is 125 bar. What is the
.co
ideal intermediate pressure at the end of first stage for a 3-stage air
(a) 25 bar (b) 5 bar (c) 10 bar (d) 20 bar
IES-35. Ans. (b)
IES-36.
(a) Ammonia reciprocating compressor

(c) Absorption refrigeration system
IES-36. Ans. (b)
tas
For an air-conditioning plant above 300 ton, which one of the following
systems would normally be preferred?
(b) Centrifugal chiller
(d) Hermetic compressor
[IES-1997]
lda
IES-37. When the discharge pressure is too high in a refrigeration system, high
pressure control is installed to: [IES-1996]
(a) Stop the cooling fan (b) Stop the water circulating pump.
(c) Regulate the flow of cooling water (d) Stop the compressor.
IES-37. Ans. (d)
vi
IES-38. The optimum intermediate pressure Pi for a gas turbine plant operating
between pressure limits P1 and P2 with perfect inter cooling between the
Ci
two stages of compression (with identical isentropic efficiency is given by:

1
(a) Pi= P2-P1 (b) Pi= (P1+P2) [IES-2003, IES-1996]
2
(c) Pi= P1 P2 (d) Pi= P22 − P12
w.
IES-38. Ans. (c). We know that for minimum compressor work pressure ratio of both stage
P1 P
must be same so = i or Pi= P1 P2
Pi P2
ww
IES-39. For a two stage-reciprocating compressor, compression from P1 to P2 is with

perfect inter-cooling and no Pressure losses. If compression in both
cylinders follows the same poly-tropic process and the atmospheric
pressure is Pa , then the intermediate pressure Pi is given by: [IES-1994]
1
(a) Pi= P2-P1 (b) Pi= (P1+P2) (c) Pi= P1 P2 (d) Pi= P22 − P12
2
IES-39. Ans. (c). We know that for minimum compressor work pressure ratio of both stages
P1 P
must be same so = i or Pi= P1 P2
Pi P2
Note: Here Pa is superfluous data that has no use.
Page 48 of 128
IES-40. 3-stage reciprocating compressors have suction pressure of 1 bar and

delivery pressure of 27 bar. For minimum work of compression, the delivery
pressure of first stage is: [IES-1999]
(a) 14 bar (b) 9 bar (c) 5.196 bar (d) 3 bar
IES-40. Ans. (d). We know that for minimum compressor work pressure ratio of 3-stage must
be same so Pi1 = Pi 2 = P 2 = 3 Pi1 Pi 2 P2 =3 P2
P 1 P i1 P i2
P P P
1 i1 i2 P 1
or Pi1= P1 × P= P12/3 .P21/3 = 1× 271/3 = 3 bar
m
3 2
P
1
IES-41. In a gas turbine cycle with two stages of reheating, working between
.co
maximum pressure P1 and minimum pressure P4, the optimum pressures
would be: [IES-1993]
(a) (P1P4) 1/3 and (P1P4) 2/3 (b) (P12 P4) 1/3 and (P1P42) 1/3
(c) (P1P4) 1/2 and P1P42/3 (d) (P1P4) 1/2 and (P1P4) 2/3
IES-41. Ans. (b) We know that for minimum compressor work pressure ratio of 3-stage must be
P
or P2 = P1 × 3
P P P P P
same so = 2 = 3 = 4 = 3 2 3 4 = 3 4
P1 P2 P3 P1 P2 P3
P4
P1
P
P1
= (P12 P4)1/3
tas and P3 =
P4
P
3 4
= (P1P42)1/3
lda
P1
Alternatively you may give answer by dimensional similarity. Only choice (b) has the
dimension of pressure.
IES-42. Four-stage compressor with perfect inter-cooling between stages

vi
compresses air from 1 bar to 16 bar. The optimum pressure in the last
intercooler will be: [IES-1998]
(a) 6 bar (b) 8 bar (c) 10 bar (d) 12 bar
IES-42. Ans. (b): We know that for minimum compressor work pressure ratio of 4-stage must
Ci
be same so P i1 = P i2 = P i3 = P 2 = 4 Pi1 Pi 2 Pi 3 P2 =4 P 2
P 1 P i1 P i2 P i3
P P P1 i1 i2 P i3 P 1
or Pi3 = P2 = P1 1/4P2 ¾ =11/4x(16) ¾ = 8 bar

w.
P2
4
P1

ww
IES-43. Which one of the following statements is correct for reciprocating air
(a)Its volumetric efficiency increases with increasing clearance ratio
(b)Its volumetric efficiency increases with increasing pressure ratio
(c)Its volumetric efficiency does not vary with change in clearance ratio and pressure
ratio
(d)Its volumetric efficiency decreases with increasing clearance ratio and pressure
ratio, both
1
⎛ p ⎞n
IES-43. Ans. (d) ηv = 1 + C – C. ⎜⎜ 2 ⎟⎟
⎝ p1 ⎠
Page 49 of 128
Volumetric efficiency of a reciprocating air compressor increases with
1.Increase in clearance ratio
2.Decrease in delivery pressure
3.Multi-staging
Which of the statements given above is/are correct?
(a) Only 1 and 2 (b) Only 2 and 3 (c) Only 3 (d) 1, 2 and 3
1
⎛ p ⎞n
IES-44. Ans. (b) ηv = 1 + C − C ⎜ 2 ⎟ if p2 ↓ thenηv ↑
m
⎝ p1 ⎠
IES-45. Which of the following statements are correct for multi staging in a
.co
reciprocating air compressor? [IES-2006]
1.It decreases the volumetric efficiency.
2.The work done can be reduced.
3. small high-pressure cylinder is required.
4.The size of flywheel is reduced.
Select the correct answer using the codes given below
(a) 1, 2 and 3
tas
(b) 2, 3 and 4 (c) 1, 3 and 4
IES-45. Ans. (b) 1 is false, it increases the volumetric efficiency.
IES-46. Consider the following statements

(d) 1, 2 and 4
[IES-2000]
The volumetric efficiency of a reciprocating compressor can be enhanced
lda
by:
1. Heating the intake air
2. Decreasing the clearance volume
3. Cooling the intake air
Which of these statements is/are correct?
vi
(a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 3 alone

IES-46. Ans. (c)
IES-47. Assertion (A): Decrease of pressure and increase of temperature of the

Ci
refrigerant in the suction pipeline connecting the evaporator to the

reciprocating compressor reduces the refrigerating capacity of the system.[IES-2003]
Reason (R): Decrease of pressure and increase of temperature of the
refrigerant in the suction pipeline connecting the evaporator to the
w.
compressor reduces the volumetric efficiency of the reciprocating

compressor.
ww

IES-47. Ans. (a)
IES-48. The ratio of the clearance volume to the displacement volume of a R12
reciprocating compressor is 0.05. Specific volume at inlet and outlet of
compressor are 0.04 and 0.02 m3/kg respectively. Volumetric efficiency of the
compressor is: [IES-2002]
(a) 95.0% (b) 47.5% (c) 38.0% (d) 19.0%
IES-48. Ans. (a)
Page 50 of 128
IES-49. The bore and stroke of the cylinder of a 6-cylinder engine working on an
Otto-cycle are 17 cm and 30 cm respectively, total clearance volume is 9225
cm3, then what is the compression ratio? [IES-2009]
(a) 7.8 (b) 6.2 (c) 15.8 (d) 5.4
9225
IES-49. Ans. (d) Clearance volume of a single cylinder = = 1537.5 cm3
6
π 2 π
Swept volume = VS = d L = × (172 ) × 30 = 6805.95 cm3
4 4
m
VS 6805.95
Compression ratio = 1 + = 1+ = 5.42
VC 1537.50
.co
The volumetric efficiency of a compressor depends upon
1. Clearance volume 2. Pressure ratio 3. Index of expansion
Of these correct statements are:
(a) 1 and 2 (b) 1 and 3 (c) 2 and 3 (d) 1, 2, and 3
IES-50. Ans. (d) The volumetric efficiency of a compressor depends upon
IES-51.
1. Clearance volume
tas
2. Pressure ratio 3. Index of expansion
A gas engine has a swept volume of 300 cc and clearance volume of 25 cc. Its
volumetric efficiency is 0.88 and mechanical efficiency is 0.90. What is the
volume of the mixture taken in per stroke? [IES-1995]
lda
(a) 248 cc (b) 252 cc (c) 264 cc (d) 286 cc
Volume of mixture
IES-51. Ans. (c) Volumetric η = , and
300
Volume of mixture = 300 × 0.88 = 264 cc
vi
IES-52. Which one of the following graphs shows the correct representation of the
processes for a two stage air compressor with perfect intercooling and no
pressure drop in the intercooler? [IES-2009]
Ci
w.
ww
Page 51 of 128
m
.co
IES-52. Ans. (b)
Effect of Clearance on Work

IES-53.
tas
A large clearance volume in a reciprocating compressor results in
lda
(a) Reduced volume flow rate (b) Increased volume flow rate
(c) Lower suction pressure (d) Lower delivery pressure [IES-1995]
IES-53. Ans. (a)
Performance Characteristics of Reciprocating Compressors

vi
IES-54. Which of the following techniques are employed for control of reciprocating
compressors? [IES-2007]
1. Throttle control 2. Clearance control 3. Blowing air to waste
Ci
(a) 1, 2 and 3 (b) 1 and 2 only (c) 2 and 3 only (d) 1 and 3 only
IES-54. Ans. (d)
IES-55. Consider the following factors: [IES-1999]

w.
1. Cylinder size 2. Clearance ratio

3. Delivery pressure 4. Compressor shaft power
The factors which affect the volumetric efficiency of a single-stage
reciprocating air compressor would include
(c) 1 and 2 (b) 3 and 4 (c) 2 and 3 (d) 1 and 4
ww
IES-55. Ans. (a) Volumetric efficiency of a single stage reciprocating air compressor is
1
⎛ p ⎞n
ηv = 1 + C – C. ⎜⎜ 2 ⎟⎟ dependent on clearance ratio and delivery pressure.
⎝ p1 ⎠
Page 52 of 128
Refriger
rant Com
mpressor
rs
S K Monda
M l’s Chaptter 4
IES-56. The
T diag
gram show wn in the
figure
f epresents reversib
re ble
compressi
c on of air on the p p-V
co-ordinat
c tes. The work of
compressi
c on need
ded by a
centrifuga
c al compres ssor is equ
ual
to
t the areaa
(a) ABDE-AABC
(b) ABDE
m
(c) ABFG
(d) ABFG-A
ABC
[IES
S-1999]
.co
IES-56. An
ns. (c)
Rotary
y Comp
pressors
s
IES-57. Assertion
A (A): A vane e type rotaary compre essor is a roto-dynam
r mic machin ne.
Reason(R)): A roto-d
through
t thhe rotating
(a) Both A and
(b) Both A and
a R are in
a R are in
dynamic m
g part of th
(c) A is truee but R is fa

tas
machine iss one in which
he machine e.
w uid flows freely
a flu
ndividually true and R is the correect explanattion of A

ndividually true but R is not the ccorrect expla
alse
[IES
anation of A
S-2005]
lda
(d) A is falsse but R is trrue
IES-57. An
ns. (a)
IES-58. The
T inlet and
a exit velocity
v dia
agrams of a turboma
achine rotor are sho
own in
the
t given figure.
f Thee turbo-maachine is: [IES-2002
2; 1993]
vi
Ci
w.
(a) An axiall compressoor with back kward curveed blades

(b) A radiall compressor with back kward curved blades
ww
(c) A radiall compressor with forwa ard curved blades

b
(d) An axiall compressoor with forw ward curved blades
IES-58. An
ns. (c) Fromm inlet and outlet diag grams it willl be seen thhe blade vellocity u2 > u1 from
which
w it is clear
c that itt is radial coompressor. For axial coompressor, u2 = u1. Furrther in
outlet
o veloccity trianglee, velocity Vr2 is in thee direction oof u2 which means blad des are
forward
f curved. In ca ase of back kward curv ved blades the direction of Vr2 will w be
opposite
o to that of u2 i.e. angle bettween Vr2 & u2 will be aacute.
Centriffugal Compres
C ssors
IES-59. In
I the cenntrifugal air
a compre essor desig gn practice, the valu ue of poly
ytropic
exponent
e of
o compres ssion is gen
nerally tak ken as [IES
S-1998]
(a) 1.2 (b) 1.3 (c) 1.4 (d) 1.5
Page 53 of 128
IES-59. Ans. (c)
IES-60. What does application of centrifugal air compressors lead to?

(a) Large frontal area of aircraft [IES-2006]
(b) Higher flow rate through the engine
(c) Higher aircraft speed
(d) Lower frontal area of the aircraft
IES-60. Ans. (a)
m
IES-61. In a centrifugal compressor, how can the pressure ratio be increased?
(a) Only by increasing the tip speed [IES-2006]
(b) Only by decreasing the inlet temperature
.co
(c) By both (a) and (b)
(d) Only by increasing the inlet temperature
IES-61. Ans. (c)
IES-62. The pressure rise in the impeller of centrifugal compressor is achieved by: [IES-200
(a) The decrease in volume and diffusion action
tas
(b) The centrifugal action and decrease in volume
(c) The centrifugal and diffusion action
(d) The centrifugal and push-pull action
IES-62. Ans. (c)
lda
IES-63. The flow in the vane less space between the impeller exit and diffuser inlet
of a centrifugal compressor can be assumed as [IES-2001]
(a) Free vortex (b) Forced vortex
(c) Solid body rotation (d) Logarithmic spiral
IES-63. Ans. (d)
vi
IES-64. Consider the following statements [IES-2000]

In centrifugal compressors, there is a tendency of increasing surge when
1. The number of diffuser vanes is less than the number of impeller vanes
Ci
2. The number of diffuser vanes is greater than the number of impeller

vanes
3. The number of diffuser vanes is equal 10 the number of impeller vanes
4. Mass flow is greatly in excess of that corresponding to the design mass
w.
flow
(a) 1 and 4 (b) 2 alone (c) 3 and 4 (d) 2 and 4
IES-64. Ans. (b)
ww
IES-65. In a radial blade centrifugal compressor, the velocity of blade tip is 400 m/s
and slip factor is 0.9. Assuming the absolute velocity at inlet to be axial,
what is the work done per kg of flow? [IES-2005]
(a) 36 kJ (b) 72 kJ (c) 144kJ (d) 360 kJ
IES-65. Ans. (c)
IES-66. In centrifugal compressor terminology, vane less space refers to the space
between [IES-1999]
(a) The inlet and blade inlet edge (b) Blades in the impeller
(c) Diffuser exit and volute casing (d) Impeller tip and diffuser inlet edge
IES-66. Ans. (d)
Page 54 of 128
IES-67. Centrifugal compressors are suitable for large discharge and wider mass
flow range, but at a relatively low discharge pressure of the order of 10
bars, because of: [IES-1997]
(a) Low pressure ratio (b) Limitation of size of receiver
(c) Large speeds (d) High compression index
IES-67. Ans. (a) Pressure ratio is low for centrifugal compressors
IES-68. Given: Vw2 = velocity of whirl at outlet [IES-1997]

u2 = peripheral velocity of the blade tips
m
The degree of reaction in a centrifugal compressor is equal to:
Vw 2 u2 2Vw 2 Vw 2
(a )1 − (b)1 − (c)1 − ( d )1 −
2u2 2Vw 2 u2 u2
.co
IES-68. Ans. (a)
IES-69. For large tonnage (more than 200 tons) air-conditioning applications, which
one of the following types of compressors is recommended? [IES-1996]
(a) Reciprocating (b) Rotating (c) Centrifugal (d) Screw
IES-70.
tas
IES-69. Ans. (d) For large tonnage air conditioning applications, specially built centrifugal
compressors are used.
In a centrifugal compressor assuming the same overall dimensions, blade

inlet angle and rotational speeds, which of the following bladings will given
lda
the maximum pressure rise? [IES-1995]
(a) Forward curved blades
(b) Backward curved blades.
(c) Radial blades
(d) All three types of bladings have the same pressure rise.
IES-70. Ans. (a) Forward curved blades give maximum pressure rise.
vi
IES-71. In a centrifugal compressor, the highest Mach number leading to

shockwave in the fluid flow occurs at [IES-1995]
(a) Diffuser inlet radius (b) Diffuser outlet radius
Ci
(c) Impeller inlet radius (d) Impeller outer radius

IES-71. Ans. (c)
IES-72. If two geometrically similar impellers of a centrifugal compressor are

w.
operated at the same speed, then their head, discharge and power will vary
with their diameter ratio 'd' as [IES-1994]
(a) d, d2 and d3 respectively (b) d2, d3 and d5 respectively
(c) d, d3 and d5 respectively (d) d2, d and d3 respectively
ww
IES-72. Ans. (d) Head, discharge and power are proportional to d2, d and d3.
IES-73. The stagnation pressure rise in a centrifugal compressor stage takes place.
(a) Only in the diffuser (b) In the diffuser and impeller [IES-1994]
(c) Only in the impeller (d) Only in the inlet guide vanes
IES-73. Ans. (a)
IES-74. A multistage compressor is to be designed for a given flow rate and pressure
ratio. If the compressor consists of axial flow stages followed by centrifugal
instead of only axial flow stages, then the [IES-1993]
(a) Overall diameter would be decreased
(b) Overall diameter would be increased
Page 55 of 128
(c) Axial length of the compressor would be increased
(d) Axial length of the compressor would be decreased
IES-74. Ans. (b) In case of axial flow stages, diameter will be less and same but in case of
centrifugal compressor, the flow is radial at outlet and thus overall diameter will
increase.
IES-75. Assertion (A): Multistaging compression is done only in reciprocating

compressors. [IES-2009]
Reason (R): Reciprocating compressor are used to compress large pressure
m
ratio at low discharge.
(a) Both A and R are individually true and R is the correct explanation of A.
(b) Both A and R are individually true but R is not the correct explanation of A.
.co
(c) A is true but R is false.
(d) A is false but R is true.
IES-75. Ans. (d) Multi-staging compression is done for both rotary and reciprocating
compressors.
IES-76. When the outlet angle from the rotor of a centrifugal compressor is more
than 90, then the blades are said to be:
(a) Forward curved
(c) Radial
IES-76. Ans. (a)
tas
(b) Backward curved
[IES-1992]
(d) Either backward or forward curved

lda
Performance Characteristics of Centrifugal Compressors
IES-77. Which one of the following
expresses the isentropic
efficiency ɳ of the
compression process in terms
vi
of enthalpy changes as
indicated in the figure given
above?
Ci
ΔH s
(a) η=
ΔH
ΔH
(b) η=
ΔH s
w.
( ΔH − Δ H s )
(c) η=
ΔH
( ΔH − ΔH s )
(d) η=
ww
ΔH s
[IES-2005]
IES-77. Ans. (a)
Page 56 of 128
IES-78. Which portion of the centrifugal
compressor characteristics
shown in the figure is difficult
to obtain experimentally?
(a) RS
(b) ST
(c) TU
(d) UV
m
[IES-2001]
.co
IES-78. Ans. (a)
IES-79. For centrifugal compressors, which one of the following is the correct
relationship between pressure coefficient ( φ p) slip factor ( φ s) work input
(a) φ p =
IES-79. Ans. (c)

φs × φw
ηa
(b) φ p =
φw
φs × η a tas
factor ( φ w) and isentropic efficiency ( η a)? [IES-2005]
(c) φ p = φs × φw ×η a (d) φ p =
φs ×η a
φw
lda
IES-80. Which one of the following is the effect of blade shape on performance of a
centrifugal compressor? [IES-1996]
(a) Backward curved blade has poor efficiency.
(b) Forward curved blade has higher efficiency.
(c) Backward curved blades lead to stable performance.
vi
(d) Forward curved blades produce lower pressure ratio.

IES-80. Ans. (c) In centrifugal compressor, backward curved blades lead to stable performance.
IES-81. The curve in the given figure

Ci
shows the variation of

theoretical pressure ratio with
mass of flow rate for a
compressor running at a
w.
constant speed. The permissible

operating range of the
compressor is represented by
the part of the curve from
ww
(a) A to B (b) B to C
(c) B to D (d) D to E
[IES-1995]
IES-81. Ans. (c) Curve B to D represents permissible operating range of compressor.
Axial flow compressor

IES-82. Consider the following statements pertaining to axial flow compressors:
1. Like centrifugal compressor, axial flow compressors are limited by surge
at low mass flow rates. [IES-2009]
2. Axial flow compressors experience choking at low flow rates.
3. The design point of axial flow compressors is close to the surge limit.
Page 57 of 128
4. As mass flow diminishes the compressor blades stall causing flow
separation.
Which of the above statements is/are correct?
(a) 1 and 2 only (b) 1, 2 and 3 (c) 1, 3 and 4 (d) 3 and 4 only
IES-82. Ans. (d)
IES-83. In an axial flow compressor, when the degree of reaction is 50%, it implies
that [IES-2006]
(a) Work done in compression will be the least
m
(b) 50% stages of the compressor will be ineffective
(c) Pressure after compression will be optimum
(d) The compressor will have symmetrical blades
.co
IES-83. Ans. (d)

For a large aviation gas turbine an axial flow compressor is usually
preferred over centrifugal compressor because
1. The maximum efficiency is higher
2. The frontal area is lower
3. The pressure rise per stage is more
4. The cost is lower tas
(a) 1 and 4 (b) Only 1 and 2 (c) 1,2 and 3 (d) 2,3 and 4
lda
IES-84. Ans. (b)
IES-85. While flowing through the rotor blades in an axial flow air compressor, the
relative velocity of air: [IES-2005]
(a) Continuously decreases (b) Continuously increases
(c) First increases and then decreases (d) First decreases and then increases
vi
IES-85. Ans. (a)
IES-86. What is the ratio of the static enthalpy rise in the rotor to the static
Ci
enthalpy rise in the stage of an axial flow compressor defined as?

(a) Power input factor (b) Flow coefficient [IES-2008]
(c) Temperature coefficient (d) Degree of reaction
IES-86. Ans. (d) Degree of Reaction: A certain amount of distribution of pressure (a rise in
w.
static pressure) takes place as the air passes through the rotor as well as the stator;
the rise in pressure through the stage is in general, attributed to both the blade rows.
The term degree of reaction is a measure of the extent to which the rotor itself
contributes to the increase in the static head of fluid. It is defined as the ratio of the
static enthalpy rise in the rotor to that in the whole stage. Variation of over the
ww
relevant temperature range will be negligibly small and hence this ratio of enthalpy
rise will be equal to the corresponding temperature rise.
IES-87. Which one of the following is the correct expression for the degree of
reaction for an axial-flow air compressor? [IES-2004]
Work input to the rotor Change of enthalpy in the rotor
(a) (b)
Work input to the stage Change of enthalpy in the stage
Pressure rise in the rotor Isentropic work
(c) (d)
Pressure rise in the stage Actual work
IES-87. Ans. (b) Degree of reaction,
Page 58 of 128
2 2
Enthalpy rise in rotor h − h0 Vr1 − Vr2
R= = 1 =
Enthalpy rise in the stage h2 − h0 2Vb ΔVw
By re-arrangement,
V 2 (sec 2 β1 − sec 2 β2 ) V
R= f = f (tan β1 + tan β 2 )
2VbVf (tan β1 − tan β 2 ) 2Vb
m
IES-88. If the static temperature rise in the rotor and stator respectively are ∆TA
and ∆TB, the degree of reaction in an axial flow compressor is given by:
ΔTA ΔTA ΔTB ΔTB
(a) (b) (c) (d) [IES-1999]
ΔTB ΔTA +ΔTB ΔTA +ΔTB ΔTA
.co
Static temperature rise in rotor
IES-88. Ans. (b) Degreeof reaction of axial flow compressor =
Static temperature rise in stage
ΔTA
=
ΔTA +ΔTB
IES-89.
enthalpy rise in the tas
Degree of reaction in an axial compressor is defined as the ratio of static
(a) Rotor to static enthalpy rise in the stator

(b) Stator to static enthalpy rise in the rotor
[IES-1996]
lda
(c) Rotor to static enthalpy rise in the stage
(d) Stator to static enthalpy rise in the stage
IES-89. Ans. (c) Degree of reaction in an axial compressor is defined as the ratio of static
enthalpy rise in the rotor to static enthalpy rise in the stage.
IES-90. Compared to axial compressors centrifugal compressors are more suitable

vi
for [IES-2002]
(a) High head, low flow rate (b) Low head, low flow rate
(c) Low head, high flow rate (d) High head, high flow rate
Ci
IES-90. Ans. (c)
IES-91. Stalling of blades in axial- flow compressor is the phenomenon of:

(a) Air stream blocking the passage [IES-2002]
(b) Motion of air at sonic velocity
w.
(c) Unsteady, periodic and reversed flow

(d) Air steam not able to follow the blade contour
IES-91. Ans. (d) Same Q. [IES-2007]
ww
IES-92. In an axial flow compressor [IES-2002]

α1 =exit angle from stator β1 = inlet angle to rotor
α2 = inlet angle to stator β2 = outlet angle from rotor
The condition to have a 50% degree of reaction is:
(a) α1 = β2 (b) α2 = β1 (c) α1 = β2 and β1 = α2 (d) α1 = α2 and β1 = β2
IES-92. Ans. (c)
IES-93. In an axial flow compressor design, velocity diagrams are constructed from
the experimental data of aerofoil cascades. Which one of the following
statements in this regard is correct? [IES-2000]
(a) Incidence angle of the approaching air is measured from the trailing edge of the
blade
Page 59 of 128
Re
efrigeran
nt Comp
pressors
S K Mo
ondal’ss Chapte
C r4
(b) δ is the dev
viation anglle between the
t angle off incidence and tangent to the cammber
linee.
(c) The deflecttion ε of thee gas stream
m while passsing through the casccade is given
n by
ε = α1 − α 2
(d) ε is the su
um of the an
ngle of incidence and camber
c lesss any devia
ation angle, i.e.,
ε = i +θ −δ
ES-93. Ans. (c)
IE
m
IE
ES-94. Thhe turbo machine
m ussed to circ
culate refr
frigerant in a large refrigerattion
plaant is: [IES-19998]
(a) A centrifug
gal compressor (b) A rad
dial turbine
(c) An axial co
ompressor (d) An ax
xial turbine
.co
ES-94. Ans. (a)
IE
ES-95.
IE Thhe energy transfer pr rocess is: [IES-19
998]
(a) Continuouss in a reciprrocating com
mpressor annd intermitttent in an axxial compressor
(b) Continuouss in an axiaal compressoor and interrmittent in a reciprocatting compressor
IE
(d) Intermitten
ES-95. Ans. (b)
IE
ES-96.
thee whirl com
nt in both reciprocating
In an axial fllow compr

mponent of
ressor stag
tas
(c) Continuouss in both reciprocating and axial compressors
g and axial compressorrs
o the air le
ge, air ente aves the stage axially
ers and lea
eaving the rotor is half the mean periphe
y. If
eral
lda
vellocity of th
he rotor bla ades, then the degree of reaction will be:: [IES
S-199
(a) 1.00 (b) 0.75 (c) 0.50 (d)0.25
ES-96. Ans. (b) Degree
IE e of reactio on,
Enthalpy
E risse in rotor
R=
Ennthalpy rise in the stagee
vi
V 1
DR = 1 − w 2 = 1 − = 0.75
2Vb 2×2
Ci
IE
ES-97. If an
a axial fllow compr ressor is designed fo or a consta ant velocitty throughh all
sta
ages, then the
t area off annulus o
of the succ ceeding sta ages will:
(a) Remain the e same (b) Progrressively deccrease [IES-19
998]
(c) Progressive ely increasee (d) Depennd upon thee number off stages
w.
ES-97. Ans. (b) as presssure increasses volume will decreasse

IE
ww
Fig ow compressor
g. Axial flo
Page 60 of 128
IES-98. The inlet and exit velocity diagrams of a turbo-machine rotor are shown in
the Figure I and Figure II respectively. [IES-1995]
m
.co
The turbo-machine is:
(a) An axial compressor with radial blades
(b) A radial compressor with radial blades.
(c) A radial compressor with forward curved blades
(d) An axial compressor with forward curved blades.
IES-98. Ans. (a) Velocity diagrams are for axial compressor (u1 = u2) with radial blades (V1 and
IES-99. tas
Vr2) are perpendicular to u1 and u2).
In a multi-stage axial flow compressor with equal temperature rise in all

stages, the pressure ratio in the subsequent stages
(a) Remains constant (b) Increases gradually
[IES-2007]
lda
(c) Decreases (d) Increases rapidly
IES-99. Ans. (a)
IES-110. Consider the following statements in respect of axial flow compressor:

1. An axial flow air compressor is often describe is a reversed reaction
vi
turbine. [IES-2007]
2. With 50% degree of reaction, the velocity diagrams are symmetrical.
(a) 1 only (b) 2 only (c) Both 1 and 2 (d) Neither 1 nor 2
Ci
IES-110. Ans. (c)
IES-111. Stalling phenomena in an axial flow compressor stage is caused due to

which one of the following? [IES-2007]
w.
(a) Higher mass flow rate than the designed value

(b) Lower mass flow rate than the designed value
(c) Higher mass flow rate or non-uniformity in the blade profile
(d) Lower mass flow rate or non-uniformity in the blade profile
IES-111. Ans. (d)
ww
IES-112. Consider the following statements regarding the axial flow in an air
compressor: [IES-2001]
1. Surging is a local phenomenon while stalling affects the entire
compressor.
2. Stalling is a local phenomenon while surging affects the entire
compressor.
3. The pressure ratio of an axial compressor stage is smaller than that of a
centrifugal compressor stage.
Of these statements are correct:
(a) 1, 2 and 3 (b) 1 and 2 (c) 2 and 3 (d) 1 and 3
IES-112. Ans. (c)
Page 61 of 128
Re
efrigeran
nt Comp
pressors
S K Mo
ondal’ss Chapte
C r4
IE
ES-113. In the graph
h as show wn above,
for
r an axiall flow compressor,
sur
rging is likely
l to occur in
whhich one of the following
zon
nes?
[IES
S-
m
2009]
(a) A ( B
(b) (c)) C (d) D
.co
IE
ES-113. Anss. (a)
tas
lda
IE
ES-114. Hig gh positivee incidence e in an axiial compre essor blade e row leadss to:
(a) Suppreession of sepparation of flow
f on the blade
b [IES-19
994]
(b) Chokin
ng of the floww
vi
(c) Separattion of flow on the sucttion side of the

t blade
(d) Separattion of flow on the presssure side off the blade
IE
ES-114. Ans s. (a)
Ci
IE
ES-115. Asssertion (A)): In axial flowf compreessors, mom mentum blad ding is more efficient than
t
raddial flow bla
ading. [IES-19997]
Reason (R): In I radial flow blading,, the pressu ure head in
ncreases duee to centrifu
ugal
heaad.
w.
(a) Both A and d R are indiv vidually tru

ue and R is the
t correct eexplanation
n of A
(b) Both A and d R are indiv vidually tru
ue but R is not
n the corrrect explana
ation of A
(c) A is true buut R is falsee
(d) A is false but
b R is truee
ww
IE
ES-115. Ans s. (b)
IE
ES-116. Asssertion (A)): The work k required per kg of air flow / min. for axial floow compressors
is lower than that
t for centtrifugal commpressor forr the same pressure
p rattio. [IES-19
995]
Reason (R): The T isentroopic efficienccy of axial flow
f compreessor is muuch higher than
t
thaat of a centrifugal comp pressor.
(a) Both A and d R are indiv vidually tru
ue and R is the
t correct eexplanation n of A
(b) Both A and d R are indiv vidually tru
ue but R is not
n the corrrect explana ation of A
(c) A is true buut R is falsee
(d) A is false but
b R is truee
IE
ES-116. Ans s. (a) Both A and R are correct and d R providess right expla
anation for A.
Page 62 of 128
IES-117. In air-craft gas turbines, the axial flow compressor is preferred because
(a) Of high pressure rise (b) It is stall free [IES-1993]
(c) Of low frontal area (d) Of higher thrust
IES-117. Ans. (c) Axial flow compressor is preferred in aircraft gas turbines because of
requirement of low frontal area.
IES-118. In axial flow compressor, exit flow angle deviation from the blade angle is a
function of: [IES-1993]
(a) Blade camber (b) Space-chord ratio
m
(c) Both blade camber and space-chord ratio
(d) Blade camber and incidence angle
IES-118. Ans. (c)
.co
IES-119. Match List-I with List-II (Pertaining to blower performance) and select the
List-I List-Il
A. Slip 1. Reduction of whirl velocity
B. Stall 2. Fixed mass flow rate regardless of
pressure ratio
C. Choking
Codes:
(a)
A
4
B
3
C
2 (b)
A
4
tas
3. Flow separation
4. Flow area reduction
B
1
C
3
lda
(c) 1 3 2 (d) 2 3 4
IES-119. Ans. (c)
IES-120. Under which one of the following sets of conditions will a supersonic
compressor have the highest efficiency? [IES-1995]
(a) Rotor inlet velocity is supersonic and exit velocity subsonic; stator inlet velocity is
vi
subsonic and exit velocity is subsonic.

(b) Rotor inlet velocity is supersonic and exit velocity subsonic; stator inlet velocity is
supersonic and exit velocity is subsonic.
Ci
(c) Rotor inlet velocity is supersonic and exit velocity supersonic; stator inlet velocity
is supersonic and exit velocity is subsonic.
(d) Rotor inlet velocity is supersonic and exit velocity supersonic; stator inlet velocity
is subsonic and exit velocity is subsonic.
w.
IES-120. Ans. (d)
IES-121. Which one of the following diagrams depicts correctly the radial
distribution of axial velocity over the blades in the last stage of multistage
axial flow compressors? [IES-2009]
ww
Page 63 of 128
m
IES-121. Ans. (c)
Flash Chamber
.co
IES-122. The flash chamber in a single stage simple vapour compression cycle
(a) Increases the refrigerating effect [IES-1998]
(b) Decreases the refrigerating effect
(c) Increases the work of compression
(d) Has no effect on refrigerating effect
below the lists:

List-I
tas
IES-122. Ans. (d) Flash chamber has no effect on refrigerating effect.
IES-123. Match List-I with List-II and select the correct answer using the codes given
List-II
[IES-1998]
lda
A. Bell Colemn refrigeration 1. Compressor
B. Vapour compression refrigeration 2. Generator
C. Absorption refrigeration 3. Flash chamber
D. Jet refrigeration 4. Expansion cylinder
vi
(a) 1 4 3 2 (b) 4 1 3 2
(c) 1 4 2 3 (d) 4 1 2 3
IES-123. Ans. (d)
Ci
IES-124. Match List-I (Cycle) with List-II (Equipment) and select the correct answer
using the code given below the lists: [IES-2008]
List-I List-II
A. Air refrigeration 1. Absorber
w.
B. Vapour compression refrigeration 2. Flash chamber

C. Vapour absorption refrigeration 3. Turbine
D. Steam jet refrigeration 4. Compressor
(a) 3 2 1 4 (b) 1 4 3 2
ww
(c) 3 4 1 2 (d) 1 2 3 4
IES-124. Ans. (c)
Page 64 of 128
IAS-1. What is the cause of burn out of hermetically sealed refrigerant
compressors? [IAS-2007]
(a) Phase to phase short because of worn insulation
(b) By prolonged overload operation
m
(c) By some mechanical failure
(d) All the above
IAS-1. Ans. (d)
.co
IAS-2. Which of the following are the special features of a hermetically sealed
compressor of a refrigerator? [IAS-1999]
1. The compressor may be reciprocating to rotary type
2. No shaft seal is necessary
3. More silent in operation
IAS-2. Ans. (b)

(b) 1, 2 and 3 tas
4. COP is more than that of open compressor
Select the correct answer using the codes given below:
(a) 2 and 4 (c) 1, 3 and 4 (d) 2, 3 and 4
lda
IAS-3. Use of hermetically sealed compressor in a vapour compression
refrigeration system results in [IAS-1998]
(a) Decrease in energy consumption (b) Increase in energy consumption
(c) Increase in COP (d) Increase in pressure ratio
IAS-3. Ans. (b)
vi
IAS-4. When does L.P. cut-off occur in a refrigeration system? [IAS-2004]

(a) If the ambient temperature is low
(b) If non-condensable gases are present in the condenser
(c) If refrigerant charge is low
Ci
(d) If lubricating oil gets accumulated in the condenser

IAS-4. Ans. (a)

w.
IAS-5. The clearance volume of a reciprocating compressor directly affects

(a) Piston speed (b) Noise level [IAS-1998]
(c) Volumetric efficiency (d) Temperature of air after compression
ww
1/ n
⎛P ⎞
IAS-5. Ans. (c) ηv = 1 + c − c ⎜ 2 ⎟
⎝ P1 ⎠
IAS-6. Which of the following are the reasons for the volumetric efficiency of
reciprocating compressor being less than 100%? [IAS-1995]
1. Deviations from isentropic process.
2. Pressure drop across the valves.
3. Superheating in compressor.
4. Clearance volume.
5. Deviations from isothermal process
6. Leakages.
Select the correct answer from the codes given below:
Page 65 of 128
(a) 1, 2, 3 and 5 (b) 2, 3, 4 and 5 (c) 1, 4, 5 and 6 (d) 2, 3 and 6
IAS-6. Ans. (d) The reason for volumetric efficiency of reciprocating compressor being less that
100% are pressure drop across the valves, superheating in compressor, clearance
volume and leakages.
Effect of Clearance on Work

In a reciprocating compressor, clearance volume is provided.
m
1. So that piston does not hit and damage the valves
2 To account for differential thermal expansion of piston and cylinder
3. To account for machining tolerances
4. To achieve isentropic compression
.co
(a) 1, 2 and 3 (b) 1, 2 and 4 (c) 1, 3 and 4 (d) 2, 3 and 4
IAS-7. Ans. (a) In centrifugal compressor there also isentropic compression occurs so.
Performance Characteristics of Reciprocating Compressors

IAS-8.
(a)
(c)
Isothermal work
Indicated work
Adiabatic work
(b)tas
Performance of a reciprocating compressor is expressed by:
Indicated work
Isothermal work
(d)
Indicated work
[IAS-2003]
lda
Indicated work Adiabatic work
IAS-8. Ans. (a)
IAS-9. The isothermal efficiency of a reciprocating compressor is defined as actual

work done during compression [IAS-1994]
vi
Actual work done during compression

(a)
Isothermal work done during compression
Adiabatic work done during compression
(b)
Ci

(c)
Actual work done during compression
w.
(d)
Actual work done during adiabatic compression
IAS-9. Ans. (c)
Rotary Compressors
ww
IAS-10. A rotary compressor is used when a refrigerating system has to handle a

refrigerant with [IAS-1997]
(a) Low specific volume and high pressure difference
(b) Low specific volume and low pressure difference
(c) Large specific volume and high pressure difference
(d) Large specific volume and low pressure difference
IAS-10. Ans. (d)
Axial flow compressor

IAS-11. Consider the following characteristics: [IAS-2002]
Page 66 of 128
1. The fluid enters the pump axially and is discharged radially.
2. Maximum efficiency may be of the order of 90%.
3. Development of a low head
4. A limited suction capacity
Which of the above characteristics are possessed by axial flow pumps?
IAS-11. Ans. (b) In Axial flow pumps the fluid both enters and discharged axially.
Flash Chamber
m
IAS-12. Flash chamber is used in refrigeration for which one of the following?
(a)Decreasing the pressure during multistage compression [IAS-2007]
(b)Increasing the compressor pressure ratio
.co
(c)Effective inter-cooling medium for purpose of increasing COP
(d)Maintaining the same pressure and temperature
IAS-12. Ans. (c)
tas
vi lda
Ci
w.
ww
Page 67 of 128
Condensers & Evaporator

5. Condensers & Evaporator
m
.co
Types of Condensers
GATE-1 A condenser of a refrigeration system rejects heat at a rate of 120 kW,
while its compressor consumes a power of 30 kW. The coefficient of
performance of the system would be: [GATE-1992; IES-1995]
(a) 1/4 (b) 1/3
tas (c) 3
Net refrigeration effect = 120 - 30 = 90 kW.

Therefore, COP = 90/30 = 3
(d) 4
GATE-1 Ans. (c) Heat rejected in condenser = 120 kW: Compressor work = 30 kW;
lda
Types of Condensers
vi
IES-1. or small installations of refrigeration systems (up to 35 kW), which type

of condenser is used? [IES-2006]
(a) Shell and tube type (b) Shell and coil type
(c) Double tube type (d) Air cooled type
Ci
IES-1. Ans. (c) 1 TR = 3.5 KW

Double Pipe or tube-in-tube type:
Double pipe condensers are normally used up to 10 TR capacity.
Shell-and-coil type:
w.
These condensers are used in systems up to 50 TR capacity.

Shell-and-tube type:
This is the most common type of condenser used in systems from 2 TR upto
thousands of TR capacity.
ww
IES-2. A condenser of a refrigeration system rejects heat at a rate of 120 kW,

while its compressor consumes a power of 30 kW. The coefficient of
performance of the system would be: [GATE-1992; IES-1995]
(a) 1/4 (b) 1/3 (c) 3 (d) 4
IES-2. Ans. (c) Heat rejected in condenser = 120 kW: Compressor work = 30 kW;
Net refrigeration effect = 120 - 30 = 90 kW.
Therefore, COP = 90/30 = 3
IES-3. A pressure gauge on the discharge side of a refrigerant compressor

reads too high. The reasons could be: [IES-1995]
1. Lack of cooling water
2. Water temperature being high
Page 68 of 128

3. Dirty condenser surfaces
4. Refrigerant temperature being too high
Of these reasons:
(a) 1, 2 and 4 are valid (b) 1, 2 and 3 are valid
(c) 2, 3 and 4 are valid (d) 1, 3 and 4 are valid
IES-3. Ans. (b)
Heat Rejection Ratio
m
IES-4. In a vapour compressor refrigeration system, the compressor capacity is
420 kJ/min and refrigerating effect is 2100 kJ/minute and heat rejection
factor is 1.2. What will, respectively be the heat rejected from the
condenser and C OP? [IES-2004]
.co
(a) 5040 kJ/minute and 5 (b) 2520 kJ/minute and 5
(c) 2520 kJ/minute and 4 (d) 5040 kJ/minute and 4
IES-4. Ans. (b) Heat rejection ratio (G)
= The loading on the condenser per unit of refrigeration
Q +W W 1
= o =1 + =1 +
or G = 1 +
1
COP
Given W = 420 kJ/min
∴ Qo = 2100 kJ/min
tas
Qo
or 1.2 = 1 +
or
1
Qo
COP
COP
or COP = 5
Qo + W = 1.2.Qo = 2520 kJ/min

lda
IES-5. A refrigeration plant uses a condenser with heat rejection ratio of 1.2. If
the capacity of the plant is 210kJ/min, then what is the value of the COP
of the refrigeration plant? [IES-2005]
(a) 3 (b) 5 (c) 7 (d) 9
vi
Q Q2 1
IES-5. Ans. (b) 1 = 1.2 or = = 5 = COP
Q2 Q1 − Q2 0.2
Ci
IES-6. Experimental measurements on a refrigeration system indicate that rate

of heat extraction by the evaporator, rate of heat rejection in the
condenser and rate of heat rejection by the compressor body to
environment are 70 kW, 90 kW and 5 kW respectively. The power input
(in kW) required to operate the system is: [IES-2002]
w.
(a) 15 (b) 20 (c) 25 (d) 75

IES-6. Ans. (c)
IES-7. In vapour compression refrigeration system, at entrance to which

ww
component the working fluid is superheated vapour? [IES-2009]

(a) Evaporator (b) Condenser
(c) Compressor (d) Expansion valve
IES-7. Ans. (b)
Evaporators
IES-8. The deposition of frost on evaporator tubes of an air conditioner will
result in [IES-1992]
(a) Decrease in heat transfer (b) Increase in heat transfer
(c) No change in heat transfer (d) Increase in capacity of evaporator
IES-8. Ans. (a)
Page 69 of 128

Types of Condensers
IAS-1. Assertion (A): Condensers of large refrigerating plants including central air-
conditioning systems are invariably water-cooled. [IAS-1996]
Reason (R): Water is available at a temperature lower than that of the
surrounding air and has a higher specific heat.
m
.co
IAS-1. Ans. (a) But most important cause is high heat transfer coefficient.
Evaporators
IAS-2. When a refrigeration plant is started, the evaporator temperature
(a) It increases continuously tas

decreases from room temperature to the required value. During this
period, how does the compressor power requirement vary?
(b) It decreases and then becomes constant

(c) It increases, reaches a peak and then decreases
[IAS-2004]
lda
(d) It remains constant
IAS-2. Ans. (a)
vi
Ci
w.
ww
Page 70 of 128
Expansion Devices
6. Expansion Devices
m
.co
Capillary Tube and Its Sizing
GATE-1 In the window air conditioner, the expansion device used is [GATE-2004]
(a) capillary tube (b) thermostatic expansion valve
(c) automatic expansion valve (d) float valve
GATE-1 Ans. (a)
tas
lda
Types of Expansion Devices
IES-1. Match List-I (Expansion device) with List-II (Operation) and select the
List-l List-II
vi
A. Float valve 1. Constant degree of superheat at

B. Automatic expansion valve evaporator exit pressure
C. Internally equalized 2. Constant degree of superheat at
thermostatic expansion valve evaporator inlet pressure
Ci
D. Externally equalized 3. Constant level of refrigerant in the

thermostatic expansion valve evaporator
4. Constant pressure in the evaporator
w.
(a) 1 2 4 3 (b) 3 2 4 1
(c) 3 4 2 1 (d) 1 4 2 3
IES-1. Ans. (c)
Thermostatic-Expansion Valve
ww
IES-2. The sensing bulb of the thermostatic expansion valve is located at the
(a) Exit of the evaporator (b) Inlet of the evaporator [IES-2002]
(c) Exit of the condenser (d) Inlet of the condenser
IES-2. Ans. (a)
IES-3. A valve which maintains a constant degree of superheat at the end of the
evaporator coil, is called [IES-1993]
(a) Automatic expansion valve (b) High side float valve
(c) Thermostatic expansion valve (d) Low side float valve
IES-3. Ans. (c)
Page 71 of 128
Expansion Devices
IES-4. Which one of the following is responsible for the operation of a thermostatic
expansion valve? [IES-2005]
(a) Pressure changes in evaporator (b) Temperature changes in evaporator
(c) Degree of superheat in evaporator (d) Degree of subcooling in evaporator
IES-4. Ans. (c)
IES-5. A thermostatic expansion value in refrigeration system [IES-1992]

(a) Ensures the evaporator completely filled with refrigerant of the load
(b) Is suitable only for constant load system
m
(c) Maintains different temperatures in evaporator in proportion to load
(d) None of the above
IES-5. Ans. (a)
.co
IES-6. What is hunting of thermostatic expansion valve? [IES-2008]
(a) A variation of evaporator load with degree of Super heat
(b) A variation in pressure of the evaporator with variation of load
(c) Alternate overfeeding and starving of refrigerant flow in the evaporator
(d) This is not used in connection with expansion valve
IES-6. Ans. (c)

IES-7. Consider the following statements:
tas [IES-2000; IAS-1999]
lda
The pressure in a capillary tube of a refrigerator decreases because
1. Tube wall offers frictional resistance
2. Refrigerant accelerates in the tube
3. Tube transfer the heat
4. Potential energy decreases
vi
(a) 1 and 2 are correct (b) 1, 2 and 3 are correct

(c) 2 and 4 are correct (d) 3 and 4 are correct
IES-7. Ans. (a)
Ci
IES-8. In a domestic refrigerator, a capillary tube controls the flow of refrigerant

from the [IES-1994]
(a) Expansion valve to the evaporator (b) Evaporator to the thermostat
(c) Condenser to the expansion valve (d) Condenser to the evaporator
w.
IES-8. Ans. (d) In domestic refrigerator, a capillary tube controls the flow of refrigerant from
condenser to evaporator

ww
Types of Expansion Devices

IAS-1. An expansion valve is NOT used for reducing pressure in the [IAS-2000]
(a) Vapour compression refrigeration (b) Vapour absorption refrigeration cycle
(c) Steam-jet refrigeration cycle (d) Gas refrigeration cycle
IAS-1. Ans. (d) Steam-jet refrigeration cycle is similar to vapour compression refrigeration
cycle where mechanical compressor is substituted by steam ejector or booster.
Page 72 of 128
Expansion Devices
Automatic or Constant-Pressure Expansion Valve
IAS-2. Which one of the following types of expansion valves is suitable for a
refrigeration plant operating at constant load? [IAS-2007]
(a) Thermostatic expansion valve (b) Automatic expansion valve
(c) Capillary tube (d) None of the above
IAS-2. Ans. (b)
IAS-3. An automatic expansion value is required to maintain constant [IAS-1998]
m
(a) Pressure in the evaporator (b) Temperature in the freezer
(c) Pressure in the liquid line (d) Temperature in the condenser
IAS-3. Ans. (a)
.co
Thermostatic-Expansion Valve
IAS-4. Which one of the following is the most important function of thermostatic
expansion valve? [IAS-2003]
(a) To control the degree of superheat
(c) To control the pressure drop

tas
(b) To control the evaporator temperature
(d) To control the evaporator pressure

IAS-4. Ans. (a)
lda
Dry compression in reciprocating compressor is preferred because it
1. Prevent valve damage
2. Enables use of thermostatic expansion valve.
3. Minimizes irreversibility in the compressor.
4. Prevents washing out of the lubricating oil from cylinder walls.
vi
IAS-5. Ans. (c)
Ci

IAS-6. Consider the following statements: [IAS-1999; IES-2000]
w.
The pressure in a capillary tube of a refrigerator decreases because

1. Tube wall offers frictional resistance
2. Refrigerant accelerates in the tube
3. Tube transfer the heat
4. Potential energy decreases
ww
(a) 1 and 2 are correct (b) 1, 2 and 3 are correct
IAS-6. Ans. (a)
IAS-7. In on-off control refrigeration system, which one of the following expansion
devices is used? [IAS-2004]
(a) Capillary tube (b) Thermostat
(c) Automatic expansion valve (d) Float valve
IAS-7. Ans. (a)
Page 73 of 128
Expansion Devices
IAS-8. Which of the features of expansion valves in the following lists are correctly
matched? [IAS-2004]
Expansion Device Feature
1. Capillary tube : Choking
2. Thermostatic expansion valve : Constant temperature
3. Automatic Expansion valve : Constant degree of superheat
4. Float valve : Mass flow rate of refrigerant is
proportional to
m
IAS-8. Ans. (c)
.co
IAS-9. The throttling device used in the domestic refrigerator is: [IAS-2002]
(a) Internally equalized thermostatic expansion valve
(b) Externally equalized thermostatic expansion valve
(c) Automatic expansion valve
(d) Capillary tube
IAS-9. Ans. (d)
tas
vi lda
Ci
w.
ww
Page 74 of 128
Gas Cycle Refrigeration

7. Gas Cycle Refrigeration
m
.co
Limitations of Carnot Cycle with Gas as a Refrigerant
IES-1. Where is an air refrigeration cycle generally employed? [IES-1998; 2006]
(a) Domestic refrigerators (b) Commercial refrigerators
(c) Air-conditioning (d) Gas liquefaction
IES-1. Ans. (d)
IES-2. tas
In aircraft, air refrigeration cycle is used because of
(a) Low unit weight per tonne of refrigeration
(b) High heat transfer rate
[IES-1995]
lda
(c) Lower temperature at high-altitudes
(d) Higher coefficient of performance
IES-2. Ans. (a)
Reversed Brayton or Joule or Bell Coleman Cycle

vi
IES-3. Which one of the following is the p-v diagram for air refrigeration cycle?
Ci
w.
ww
IES-3. Ans. (a)
IES-4. Match List-I (Process) with List-II (Type) for Bell Coleman or Joule or
Reverse Brayton cycle for gas cycle refrigeration and select the correct
answer using the codes given below the lists: [IES-2003]
List-I List-II
A. Compression 1. Isobaric
Page 75 of 128

B. Heat rejection 2. Isothermal
C. Expansion 3. Isentropic
D. Heat absorption 4. Isenthalpic
(a) 3 1 4 2 (b) 3 1 3 1
(c) 3 2 3 2 (d) 3 1 2 2
IES-4. Ans. (b)
IES-5. When the Brayton cycle working in the pressure limits of p1 and p2 is
m
reversed and operated as a refrigerator, what is the ideal value of COP for
such a cycle? [IES-2007]
γ −1
⎛p ⎞ 1
(a) ⎜ 2 ⎟ −1 (b)
.co
γ −1
⎝ p1 ⎠ ⎛ p2 ⎞
⎜ ⎟ −1
⎝ p1 ⎠
1
(c) ⎧( γ −1) ⎫
(d) None of the above
⎨ γ ⎬⎭
⎛ p2 ⎞ ⎩
IES-5. Ans. (c)

⎜ ⎟
⎝ p1 ⎠
η H .E = 1 –
−1
1
rp( γ −1)/ γ
; ∴ (COP)H.P=
1
tas
ηH .E
=
rp
rp
γ −1
γ
γ −1
γ
−1
lda
1 1
(COP)R = (COP)H.P – 1 = γ −1
= γ −1
rp γ
−1 ⎛ p2 ⎞ γ
⎜ ⎟ −1
⎝ p1 ⎠
vi
Application to Aircraft Refrigeration

IES-6. While designing the refrigeration system of an aircraft prime consideration
Ci
is that the [IES-1993]

(a) System has high C.O.P.
(b) H.P./ton is low
(c) Weight of refrigerant circulated in the system is low
(d) Weight of the refrigeration equipment is low·
w.
IES-6. Ans. (d)
Simple Evaporative
IES-7. The performance of an evaporator condenser largely depends on
ww
[IES-1999]
(a) Dry bulb temperature of air (b) Wet bulb temperature of air
(c) Hot water temperature (d) Air-conditioned room temperature
IES-7. Ans. (a)
Boot-strap Evaporative
IES-8. Which is the most suitable type of air refrigeration system for supersonic
planes with Mach Number 3 or above? [IES-2005]
(a) Boot-strap (b) Simple evaporative
(c) Regenerative (d) Boot-strap evaporative
IES-8. Ans. (d) Actually for this use Reduced Ambient system of refrigeration.
Page 76 of 128

Reversed Brayton or Joule or Bell Coleman Cycle

IAS-1. Match List I with List II and select the correct answer using the codes given
below lists: [IAS-1994]
List-I List-II
A.
m
1. Vapour compression cycle
using expansion
valve
.co
B.
2. Bell-Coleman cycle (gas
tas compression cycle)

lda
C.
3. Vapour compression cycle
using expansion
vi
engine
Ci
Codes: A B C A B C
w.
(a) 1 2 3 (b) 2 3 1
(c) 1 3 2 (d) 2 1 3
IAS-1. Ans. (d)
ww
Page 77 of 128
Vapour Absorption System

8. Vapour Absorption System
m
.co
Simple Vapour Absorption System
GATE-1. List-I List II [GATE-1997]
A. Liquid to suction heat exchanger 1. Vapour absorption refrigeration
B.
C.
D.
Constant volume heat addition
Normal shock
Ammonia water tas2.
3.
4.
5.
6.
Vapour compression refrigeration
Diesel cycle
Otto cycle
Converging nozzle
Converging-diverging nozzle
lda
GATE-1. Ans. (A) –2, (B) –4, (C) –6, (D) –1
ATE-2. A vapour absorption refrigeration

system is a heat pump with three
thermal reservoirs as shown in the
figure. A refrigeration effect of 100
vi
W is required at 250 K when the

heat source available is at 400 K.
Heat rejection occurs at 300 K. The
Ci
minimum value of heat required (in

W) is:
(a) 167 (b) 100
(c) 80 (d) 20
w.
[GATE-2005]
ATE-2. Ans. (c) From question, since
refrigeration effect of 100 W is
required
ww
100 250
So, =
Work obtained 300 − 250
100 × 50
⇒ Work obtained = = 20 W
250
Now for this amount of work, heat

is absorbed from reservoir 3 and
rejected to sink 2.
Page 78 of 128
Vapour
V A
Absorptiion Syste
em
S K Monda
M l’s Chaptter 8
W 300
0 1
∴ η= =1 − = ⇒ Q3 = 4 W = 4 × 20 W = 80
0W
Q3 400
0 4
GA
ATE-3. A heat engine havin ng an effic ciency of 70% is useed to drivve a refrigerator
having
h a co-efficien
c nt of perfo ormance off 5. The energy abssorbed from m low
temperatu
t ure reservo oir by the refrigerattor for eac ch kJ of energy
e abssorbed
from
f high temperatu ure source by the eng gine is: [GATEE-2004]
(a) 0.14 kJ (b) 0.71 kJ (c) 3.5 kJ (d) 7.1 kJ
m
ATE-3.
A A
Ans. (c))
Given, ηreserrvoir = 0.7, (COP)
( R = 5
.co
ηreseervoir = ...(i )
Q1
Q2
P)R =
Now, (COP
W
Q2
⇒ 5=
∴ W= 2
W
Q
5
Q
Again, 0.7 = 2 ×
1
5 Q1
⇒
...(ii )
Q2
Q1
= 3.5
5
tas
lda
Energy abssorbed fromm low tempeerature reseervoir by thhe refrigerator for each
h kJ of
energy
e absoorbed from high
h temperrature sourcce by the en
ngine –3.5 kJ.
Pre
evious 20-Ye
ears IE
ES Que
estions
s
vi
Simple
e Vapou
ur Abso
orption System
m
Ci
IES
S-1. In
I a vapou ur absorptiion refrige
erator, hea
at is rejecte
ed in: [IES
S-2006]
(a) Condensser only (b) Geenerator only
(c) Absorbeer only (d) Condenser and absorber
IES
S-1. Ans. (d
d)
w.
IES
S-2. Assertion
A (A): In remmote place es, the use e of absorp ption refrigeration system
s
plant
p is mo ore advanttageous wh hen compa ared to vap pour comp pression pla ant.[IES-19
993]
Reason (R R): The absorption sy ystem can use relativ vely low te emperature heat
ww
a energy source.
as
(a) Both A anda R are in ndividually true and R is the correect explanattion of A
(b) Both A anda R are in ndividually true but R is not the coorrect expla
anation of A
(c) A is truee but R is fa
alse
(d) A is falsse but R is trrue
IES
S-2. Ans. (c
c) Assertion n A is correcct but reasoon is not truue. The corrrect reason should havve been
that
t no elecctricity is required for operation
o off absorption refrigeratioon system plant.
p
IES
S-3. The
T mostt common n type off absorptiion system m in usee in induustrial
applicatio
a ns is based
d on the re
efrigerant-absorbent combination of:
(a) Air-wateer (b) Litthium brom
mide-air [IES
S-1999]
(c) Carbon dioxide-watter (d) Am
mmonia-watter
Page 79 of 128

IES-3. Ans. (d)
IES-4. Solar energy can be directly used in [IES-1999]

(a) Vapour compression refrigeration system
(b) Vapour absorption refrigeration system
(c) Air refrigeration system
(d) Jet refrigeration system
IES-4. Ans. (b)
m
IES-5. Vapour absorption refrigeration system works using the [IES-1997]
(a) Ability of a substance to get easily condensed or evaporated
(b) Ability of a vapour to get compressed or expanded
.co
(c) Affinity of a substance for another substance
(d) Absorptivity of a substance
IES-5. Ans. (c) Vapour absorption refrigeration system works using the affinity of a substance for
another substance.
IES-6. Which one of the following statements regarding ammonia absorption

system is correct?
tas
The solubility of ammonia in water is:
(a) A function of the temperature and pressure of the solution
[IES-1997]
(b) A function of the pressure of the solution irrespective of the temperature

(c) A function of the temperature of the solution alone
lda
(d) Independent of the temperature and pressure of the solution
IES-6. Ans. (c)
IES-7. The refrigerant used for absorption refrigerators working heat from solar
collectors is a mixture of water and [IES-1996]
(a) Carbon dioxide (b) Sulphur dioxide
vi
(c) Lithium bromide (d) Freon 12

IES-7. Ans. (c) The refrigerant used for absorption refrigerators working on heat from solar
collectors is a mixture of water and lithium bromide.
Ci
IES-8. Waste heat can be effectively used in which one of the following
refrigeration systems? [IES-1995]
(a) Vapour compression cycle (b) Vapour absorption cycle
w.
(c) Air refrigeration cycle (d) Vortex refrigeration system

IES-8. Ans. (b) Waste heat can be utilized in vapour absorption cycle.
IES-9. Match List-I (Basic components of Aqua-ammonia refrigeration system)

with List-II (Functions of the components in the system) and select the
ww
List-I List-II
A. Generator 1. Dehydration
B. Analyzer 2. Removal of vapour from strong aqua-
ammonia solution
C. Rectifier 3. Producing dry ammonia vapour by
removing traces of water particles completely
D. Receiver 4. Storage of high pressure liquid ammonia
5. Formation of liquid ammonia from high
pressure vapours.
(a) 3 1 2 5 (b) 5 3 4 2
Page 80 of 128

(c) 1 3 2 5 (d) 2 1 3 4
IES-9. Ans. (d)
Maximum Coefficient of Performance of a Heat Operated

Refrigerating Machine
IES-10. In vapour absorption refrigeration system heating in generator is done at
177°C , refrigeration in evaporator at –3°C and cooling in condenser at 27°C.
Then what will be the maximum COP of the system? [IES-2009]
m
(a) 1.5 (b) 2.3 (c) 3.0 (d) 4.0
IES-10. Ans. (c) COP of Refrigerator
⎛ T ⎞ ⎛ TE ⎞ ⎛ 300 ⎞ ⎛ 270 ⎞
.co
= η H .E × COPR = ⎜1 − C ⎟ ⎜ ⎟ = ⎜1 − ⎟ ⎜ =3
⎝ TG ⎠ ⎝ TC − TE ⎠ ⎝ 450 ⎠⎝ 300 − 270 ⎟⎠
IES-11. Maximum possible COP of a solar absorption refrigeration system with

generator temperature of 360 K, absorber temperature of 300 K, condenser
temperature of 300 K and evaporator temperature of 270 K is:
(a) 9 (b) 6
IES-11. Ans. (d) Page no 321 Q no 104
IES-12.
(c) 3
tas (d) 1.5 [IES-2001; 2002]
Theoretical maximum COP of a vapour absorption system (where, TG =

generator temp, TE = evaporator temp, To = environmental temp) is:
lda
[IES-1998; 2003]
TE ⎛ TG − TO ⎞ TE ⎛ TO − TE ⎞ TG ⎛ TG − TO ⎞ TG ⎛ TO − TE ⎞
(a) ⎜ ⎟ (b) ⎜ ⎟ (c) ⎜ ⎟ (d) ⎜ ⎟
TG ⎝ TO − TE ⎠ TG ⎝ TG − TO ⎠ TE ⎝ TO − TE ⎠ TE ⎝ TG − TO ⎠
IES-12. Ans. (a)
vi
Electrolux Refrigerator
IES-13. In an Electrolux refrigerator: [IES-2005]
(a) Ammonia is absorbed in water (b) Ammonia is a absorbed in hydrogen
Ci
(c) Hydrogen is evaporated in ammonia (d) Ammonia evaporated in hydrogen

IES-13. Ans. (d)
w.
ww
Page 81 of 128
Vap
pour Absorption
n System
m
S K Mo
ondal’ss Chapte
C r8
m
.co
IE
ES-14. Hydrogen
(a) It acts as
tas
n is essentiial in an Ellectrolux refrigeratio
a a catalysst in the eva
aporator
r on system,, because
[IES-19997]
lda
(b) The rea action betw
ween hydrog gen and am mmonia is endothermic
e c in evaporrator
and exoothermic in absorber
(c) The coooled hydroge gerant entering
en leaving tthe heat excchanger coools the refrig
the evaaporator
(d) It helpss in maintaiining a low partial presssure for thee evaporatin
ng ammonia a
IE
ES-14. Ans. (d) Hydroogen gas in Electrolux refrigeratoor helps in maintaining a low parrtial
vi
pressure foor the evapoorating amm monia.
Prev
vious 20-Yea
2 ars IAS
S Ques
stions
Ci
Simple Vapour
V Absorp
ption S
System
w.
IA
AS-1. Absorbent in a vap pour absorrption refr rigeration system se eparates fr
rom
the refriggerant only y when it [IAS-20
007]
(a) Is sufficciently heatted (b) Is sprrayed on coooling water
(c) Is cooleed (d) Reactts with refriigerant
IA
AS-1. Ans. (a)
ww
IA
AS-2. In the ab bsorption refrigerattion cycle,, the com mpressor of o the vap pour
compression refrige eration cyc
cle is replaaced by: [IA
AS-1994; 20000]
(a) Liquid pump (b) Generrator
(c) Absorbeer and geneerator (d) Absorrber, liquid pump and generator
g
AS-2. Ans. (d) The coompressor of vapour compression refrigera
IA ation cycle is replaced
d by
absorber, liiquid pump
p and genera
ator in the absorption
a r
refrigeration
n cycle.
Page 82 of 128

Maximum Coefficient of Performance of a Heat Operated
Refrigerating Machine
IAS-3. A reversible heat engine runs between high temperature T1 and low
temperature T2. The work output of this heat engine is used to run
reversible refrigeration cycle absorbing heat at temperature T3 and
rejecting at temperature T2. What is the COP of the combined system?
⎛ T − T2 ⎞ ⎛ T3 ⎞ ⎛ T2 ⎞ ⎛ T2 − T3 ⎞
(a) ⎜ 1 ⎟⎜ ⎟ (b) ⎜ ⎟⎜ ⎟ [IAS-2004]
m
⎝ T1 ⎠ ⎝ T2 − T3 ⎠ ⎝ T1 − T2 ⎠ ⎝ T3 ⎠
⎛ T1 ⎞ ⎛ T3 ⎞ ⎛ T3 ⎞ ⎛ T1 ⎞
(c) ⎜ ⎟⎜ ⎟ (d) ⎜ ⎟⎜ ⎟
⎝ T1 − T2 ⎠ ⎝ T2 − T3 ⎠ ⎝ T1 − T3 ⎠ ⎝ T2 − T1 ⎠
.co
Q Q Q − Q2 W Q
IAS-3. Ans. (a) 1 = 2 = 1 = or W = 1 × (T1 − T2 )
T1 T2 T1 − T2 T1 − T2 T1
Q3 Q21 Q21 − Q3 W Q3
= = = or W = × (T2 − T3 )
T3 T2 T2 − T3 T2 − T3 T3
or
Q1
T1
or COP = =⎜
Q
(T1 − T2 ) = 3 (T1 − T3 )
T3
Q3 ⎛ T3 ⎞ ⎛ T1 − T2 ⎞
⎟×⎜ ⎟
Q1 ⎝ T2 − T3 ⎠ ⎝ T1 ⎠
tas
vi lda
IAS-4. For the same condenser and evaporator temperatures, the COP of
absorption refrigeration system is less than that of mechanical vapour
Ci
compression refrigeration system, since in the absorption refrigeration

system [IAS-1997]
(a) A liquid pump is used for compression
(b) A refrigerant as well as a solvent is used
w.
(c) Absorber requires heat rejection

(d) Low grade energy is used to run the system
IAS-4. Ans. (d)
ww
Page 83 of 128
Psychrometry
9. Psychrometry
m
.co
Specific humidity or Humidity ratio
GATE-1. Dew point temperature of air at one atmospheric pressure (1.013 bar) is
18oC. The air dry bulb temperature, is 30oC. The saturation pressure of
tas
water at 18oC and 30oC are 0.02062 bar and 0.04241 bar respectively. The
specific heat of air and water vapour respectively are 1.005 and 1.88 kJ/kg K
and the latent heat of vaporization of water at 0oC is 2500 kJ/kg. The
specific humidity and enthalpy (kJ/kg of dry air) of this moist air
respectively, are (a) 0.01051, 52.64 (b) 0.01291, 63.15
lda
[GATE-2004]
(c) 0.01481, 78.60 (d) 0.01532, 81.40
GATE-1Ans. (B)Given, P = 1.013 bar
PV = 0.02062 (at dew point)
We know that
vi
0.622Pv
Specific humidity =
P − Pv
0.622 × 0.02062
=
Ci
1.013 − 0.02062
= 0.01291 kg / kg of dry air
enthalpy (h) = 1.022 td+ W (hfgdp + 2.3 tdp)
= 1.022 ×30 + 0.01291 (2500 + 2.3 × 18)
= 1.022 × 30 + 32.809
w.
= 63.47 kJ / kg of dry air
Relative humidity
ww
GATE-2. A moist air sample has dry bulb temperature of 30ºC and specific humidity
of 11.5 g water vapour per kg dry air. Assume molecular weight of air as
28.93. If the saturation vapour pressure of water at 30ºC is 4.24 kPa and the
total pressure is 90 kPa, then the relative humidity (in %) of air sample is
(a) 50.5 (b) 38.5 (c) 56.5 (d) 68.5 [GATE-2010]
GATE-2Ans. (b)
Page 84 of 128
Psychrometry
Given,
w = 11.5 × 10−3 kJ / kg of dry air
Pv
w = 0.622 ; after substituting
P − Pv
Pv = 1.62KPa
Pv 1.62
∴ Relative humidity(in%) = = × 100% = 38%
Pvs 4.24
m
GATE-3. For a typical sample of ambient air (at 35 °C, 75% relative humidity and
standard atmospheric pressure), the amount of moisture in kg per kg of dry
air will be approximately [GATE-2005]
.co
(a) 0.002 (b) 0.027 (c) 0.25 (d) 0.75
P
GATE-3Ans. (b)Here, φ= v
Ps
⇒ Pv = φ.Ps
( Ps )33 c = 0.05628bar
0
ω = 0.622Pv
tas
GATE-4. For air at a given temperature, as the relative humidity is increased
isothermally, [GATE-2001]
lda
(a) the wet bulb temperature and specific enthalpy increase
(b) the wet bulb temperature and specific enthalpy decrease
(c) the wet bulb temperature increases and specific enthalpy decreases
(d) the wet bulb temperature decreases and specific enthalpy increases
GATE-4Ans. (a, c)
vi
Dew point temperature

GATE-5. Dew point temperature is the temperature at which condensation begins
Ci
when the air is cooled at constant [GATE-2006]

(a) volume (b) entropy (c) pressure (d) enthalpy
GATE-5Ans. (c)
w.
ww
Air is cooled at constant pressure to make unsaturated air to saturated one.
GATE-6. For air with a relative humidity of 80% [GATE-2003]

(a) the dry bulb temperature is less than the wet bulb temperature
(b) the dew point temperature is less than wet bulb temperature
(c) the dew point and wet bulb temperatures are equal
(d) the dry bulb and dew point temperatures are equal
Page 85 of 128
Psychrometry
GATE-6Ans. (b)
m
Psychrometric Chart
.co
GATE-7. The statements concern Psychrometric chart. [GATE-2006]
1. Constant relative humidity lines are uphill straight lines to the right
2. Constant wet bulb temperature lines are downhill straight lines to the
right
3. Constant specific volume lines are downhill straight lines to the right
4. Constant enthalpy lines are coincident with constant wet bulb
temperature lines
Which of the statements are correct?
(a) 2 and 3
GATE-7Ans. (a)
(b) 1 and 2 tas
(c) 1 and 3 (d) 2 and 4
lda
GATE-8. Various Psychrometric processes are shown in
the figure below.
Process in Figure Name of the process
P. 0-1 1.Chemical dehumidification
Q. 0-2 2. Sensible heating
vi
R. 0-3 3.Cooling and dehumidification

S. 0-4 4.Humidification with steam
injection
T. 0-5 5.Humidification with water
Ci
injection
The matching pairs are [GATE-2005]
(a) P-1, Q-2, R-3, S-4, T-5 (b) P-2, Q-1, R-3, S-5, T-4
(c) P-2, Q-1, R-3, S-4, T-5 (d) P-3, Q-4, R-5, S-1, T-2
w.
GATE-8Ans. (b)
GATE-9. When atmospheric air is heated at constant pressure, then which one is not
correct. [GATE-2000]
(a) humidity ratio does not change
ww
(b) relative humidity increases

(c) dew point temperature does not change
(d) wet bulb temperature increases
GATE-9Ans. (b)
GATE-10. During chemical dehumidification process of air [GATE-2004]

(a) dry bulb temperature and specific humidity decrease
(b) dry bulb temperature increases and specific humidity decreases
(c) dry bulb temperature decreases and specific humidity increases
(d) dry bulb temperature and specific humidity increase
GATE-10Ans. (b)
Page 86 of 128
Psychrometry
m
GATE-11. Water at 42°C is sprayed into a stream of air at atmospheric pressure, dry
bulb temperature of 40oC and a wet bulb temperature of 20oC. The air
leaving the spray humidifier is not saturated. Which of the following
.co
statements is true? [GATE-2005]
(a) Air gets cooled and humidified (b) air gets heated and humidified
(c) Air gets heated and dehumidified (d) Air gets cooled and dehumidified
GATE-11Ans. (b)Here, tDBT = 40o, tWBT = 20o
Water sprayed at temperature = 42o
Cooling and dehumidification tas

Since, t water spray > tDBT so heating and humidification.
GATE-12.For the following "Matching" exercise, choose the correct one from among
lda
the alternatives [GATE-2000]
A, B, C and D
Group 1 Group 2
1. Marine Diesel Engine (A) Two stroke engine
2. Air conditioning (B) Four stroke engine
3. Steam Power Plant (C) Rotary engine
vi
4. Gas Turbine Power Plant (D) Cooling and dehumidification

(E) Cooling tower
(F) Brayton cycle
(G) Rankine cycle
Ci
(H) D - slide valve

(a) (b) (c) (d)
1-B 1-C 1-C 1-A
2-E 2-F 2-F 2-D
w.
3-F 3-E 3-G 3-G

4-H 4-G 4-E 4-F
GATE-12Ans. (d)
ww
Air Washer
GATE-13.Air (at atmospheric pressure) at a dry bulb temperature of 40°C and wet
bulb temperature of 20°C is humidified in an air washer operating with
continuous water recirculation. The wet bulb depression (i.e. the difference
between the dry and wet bulb temperatures) at the exit is 25% of that at the
inlet. The dry bulb temperature at the exit of the air washer is closest to
(A) 100C (B) 200C (C) 250C (D) 300C [GATE-2008]
GATE-13Ans. (C)
Air Conditioning
GATE-14. Moist air at a pressure of 100 kPa is compressed to 500 kPa and then cooled
to 350C in an after cooler. The air at the entry to the after cooler is
Page 87 of 128
Psychrometry
unsaturated and becomes just saturated at the exit of the after cooler. The
saturation pressure of water at 35°C is 5.628 kPa. The partial pressure of
water vapour (in kPa) in the moist air entering the compressor is closest to
[GATE-2008]
(A) 0.57 (B) 1.13 (C) 2.26 (D) 4.5
GATE-14Ans. (B) Volume change is one fifth and water vapour just compressed to one fifth
5.628
volume so unsaturated vapour pressure= = 1.1256 ~
− 1.13kPa
5
m
Psychrometric Chart
GATE-15.The statements concern Psychrometric chart. [GATE-2006]
.co
1. Constant relative humidity lines are uphill straight lines to the right
2. Constant wet bulb temperature lines are downhill straight lines to the
right
3. Constant specific volume lines are downhill straight lines to the right
4. Constant enthalpy lines are coincident with constant wet bulb
temperature lines
Which of the statements are correct?
(a) 2 and 3
GATE-15Ans. (a)
(b) 1 and 2
tas
(c) 1 and 3 (d) 2 and 4
lda
Previous 20-Yrs IES Questions
Psychrometric Properties
vi
A psychrometer measures
1. wet bulb temperature
2. dew point temperature
Ci
3. dry bulb temperature.

On these statements
(a) 1 alone is correct (b) 2 and 3 are correct
(c) 1 and 3 are correct (d) 1, 2 and 3 are correct
IES-1Ans. (c) A psychrometer measures wet bulb temperature and dry bulb temperature. It
w.
directly not measure dew point temperature.
IES-2. If the specific heats of dry air and water vapour are 1.00 kJ/kg-K and 1.88
kJ/kg-K respectively and the humidity ratio is 0.011, then the specific heat
ww
of moist air at 25°C and 50% relative humidity will be [IES-1994]

(a) 1.0207 kJ/kg-K (b) 1.869 kJ/kg-K
(c) 1.891 kJ/kg-K (d) 0.9793 kJ/kg-K
IES-2. Ans. (a) Specific heat of moist air = specific heat of dry air + humidity ratio x specific
head of water vapour = 1.00 + 0.011 x 1.88 = 1.00 + 0.0207 = 1.0207 kJ/kgK.

IES-3. If Pa and Pv denote respectively the partial pressure of dry air and that of
water vapour in moist air, the specific humidity of air is given by
pv pv 0.622 pv 0.622 pv
(a) (b) (c) (d) [IES-;2001]
pa + pv pa pa pa + pv
Page 88 of 128
Psychrometry
IES-3Ans. (c) We know pa = pb − pv
IES-4. The humidity ratio of atmospheric air at 28°C dbt and 760 mm of Hg is 0.016
kgv/kg-da. What is the partial pressure of water vapour? [IES-2009]
(a) 2.242kN/m2 (b) 2.535kN/m2 (c) 3.535kN/m2 (d) 4.242kN/m2
IES-4Ans. (b)
⎛ PV ⎞
Humidity ratio = 0.622 ⎜ ⎟
⎝ P − PV ⎠
m
⎛ PV ⎞
⇒ 0.622 ⎜ ⎟ = 0.016
⎝ 100 − PV ⎠
⇒ PV = 2.5 kN / m2
.co
Relative humidity
IES-5. In a sample of moist air at standard atmospheric pressure of 101.325 kPa
and 26°C the partial pressure of water vapour is 1.344 kPa. If the saturation
(a) 0.00836 and 1.32%

(c) 0.01344 and 1.32%
IES-5Ans. (b)
tas
pressure of water vapour is 3.36 kPa at 26 C, then what are the humidity
ratio and relative humidity of moist air sample?
(b) 0.00836 and 40%
(d) 0.01344 and 40%
[IES-2009]
lda
Humidity ratio of Air
⎛ PV ⎞
= 0.622 ⎜ ⎟
⎝ P − PV ⎠
⎛ 1.344 ⎞
= 0.622 ⎜ ⎟
vi
⎝ 101.325 − 1.344 ⎠
= 8.36 × 10−3 = 0.00836 kgv / kg − da
Relative humidity of Moist Air Sample
Ci
P 1.344
= V = = 0.4 = 40%
PVS 3.36
pv
IES-6. The equation φ = is used to calculate the (pv = partial pressure of water
w.
ps
vapour in moist air at a given temperature, Ps = saturation pressure of
water vapour at the same temperature) [IES-1999]
(a) relative humidity (b) degree of saturation
ww
(c) specific humidity (d) absolute humidity

IES-6Ans. (a)
IES-7. If the volume of moist air with 50% relative humidity is isothermally
reduced to half its original volume, then relative humidity of moist air
becomes [IES-2003]
(a) 25 % (b) 60 % (c) 75 % (d) 100 %
IES-7Ans. (d)
Page 89 of 128
Psychrometry
pv1
Relative humidity(RH)1 = = 0.5 or pv1 = 0.5 × ps
ps
Where subscript ' v' refers to vapour state.
Where subscript ' s' refers to saturation state.
⎛V ⎞ ⎛ 2V ⎞
p v 2 = pv1 × ⎜ 2 ⎟ = ( 0.5 ps ) × ⎜ 1 ⎟ = ps
⎝ V1 ⎠ ⎝ V1 ⎠
m
p p
∴Relative humidity(RH) 2 = v 2 = s = 100%
ps ps
IES-8. The wet bulb depression is zero, when relative humidity is equal to
.co
(a) 100% (b) 60% (c) 40% (d) Zero: [IES-2006]
IES-8Ans. (a)
IES-9. Evaporative air-cooler is used effectively when [IES-1995]

(a) dry bulb temperature is very close to the wet bulb temperature
(b) dry bulb temperature is high and relative humidity is high
tas
(c) dry-bulb temperature is low and relative humidity is high
(d) dry bulb temperature is high and the relative humidity is low.
IES-9Ans. (d)
lda
IES-10. What is the saturation temperature at the partial pressure of water vapour
in the air-water vapour mixture called? [IES-2009]
(a) Dry bulb temperature (b) Web bulb temperature
vi
(c) Dew point temperature (d) Saturation temperature

IES-10Ans. (c)
Ci
IES-11. In a cooling tower, the minimum temperature to which water can be cooled
is equal to the [IES-1995; 2001]
(a) dew point temperature of the air at the inlet
(b) dry bulb temperature of the air at the inlet
(c) thermodynamic wet bulb temperature of the air at the inlet
w.
(d) mean of the dew point and dry bulb temperature of the air at the inlet
IES-11Ans. (c)
IES-12. In a chilled-water spray pond, the temperature of water is lower than dew
ww
point temperature of entering air. The air passing through the spray
undergoes [IES-1999]
(a) cooling and humidification (b) cooling and dehumidification
(c) sensible cooling (d) dehumidification
IES-12Ans. (b) In this case condensation of moisture takes place which results in fall in specific
humidity ratio. Cooling and dehumidification take place.
IES-13. When a stream of moist air is passed over a cold and dry cooling coil such
that no condensation takes place, then the air stream will get cooled along
the line of [IES-1996]
(a) constant web bulb temperature (b) constant dew point temperature
(c) constant relative humidity (d) constant enthalpy.
Page 90 of 128
Psychrometry
IES-13Ans. (b) When a stream of moist air is passed over a cold and dry cooling coil such that
no condensation takes place, then air stream is cooled along constant dew point
temperature
Degree of saturation
IES-14. If Pv is the partial pressure of vapour, Ps is the partial pressure of vapour
for saturated air and Pb is the barometric pressure, the relationship
between relative humidity ' φ ' and degree of saturation ' μ' is given by
m
⎡ pb − ps ⎤ ⎡ pb − pv ⎤
(a) μ = φ ⎢ ⎥ (b) μ = φ ⎢ ⎥
⎣ pb − pv ⎦ ⎣ pb − ps ⎦
.co
p p
(c) μ = φ v (d) μ = φ v [IES-2001]
pb ps
IES-14Ans. (a)
IES-15.
13.6°C, W = 0.01 kg/kgair)

(a) 25 (b) 30
tas
Air at state 1 (dpt 10°C, W = 0.0040 kg/kgair) mixes with air at state 2 (dpt
18°C, W = 0.0051 kg/kgair) in the ratio 1 to 3 by weight. The degree of
saturation (%) of the mixture is (the specific humidity of saturated air at
(c) 48 (d) 62
[IES-1999]
lda
IES-15Ans. (c)
0.004 + 3 × 0.0051
kg of moisture actually contained in mixture = = 0.0048
4
kg of moisture in saturated air of mixture = 0.01 kg/kg of air
0.0048
So, Degree of saturation = ×100% = 48%
vi
0.01
IES-16. Match List I with List II and select the correct answer using the code given
Ci
below the Lists: [IES-2005]

List I List II
A Degree of saturation 1. Measure of latent enthalpy of moist air
B. Dry bulb temperature 2. Measure of total enthalpy of moist air
C. Wet bulb temperature 3. Measure of the capacity of air to absorb
w.
moisture
D. Dew point temperature 4. Measure of sensible enthalpy of moist air
A B C D A B C D
(a) 2 1 3 4 (b) 3 4 2 1
ww
(c) 2 4 3 1 (d) 3 1 2 4
IES-16Ans. (b)

1.The specific humidity is the ratio of the mass of water vapour to the mass
of dry air in a given volume of the mixture
2.The relative humidity of the atmospheric air is the ratio of the actual mass
of the water vapour in a given volume to that which it would have if it were
saturated at the same temperature
3.The degree of saturation is defined as the ratio of the specific humidity of
a mixture to the specific humidity of the mixture when saturated at the
same temperature
Page 91 of 128
Psychrometry
IES-17Ans. (d)
Wet Bulb Temperature (WBT)

IES-18. In a cooling tower the sum of range and approach is equal to twice the wet
bulb depression. Then [IES-2003]
(a) Dry bulb temperature is mean of water inlet temperature and wet bulb
m
temperature
(b) Dry bulb temperature is mean of water outlet temperature and wet bulb
temperature
(c) Water inlet temperature is mean of dry bulb temperature and wet bulb
.co
temperature
(d) Water inlet temperature is mean of water outlet temperature and wet bulb
temperature
IES-18Ans. (a)
Ti = inlet temperature of water in cooling tower
Wet bulb depression = Tdb - Twb

From the given statement,
tas
To = outlet temperature of water in cooling tower
Approach = To - Twb
(Ti - To ) + (To - Twb ) = 2 (Tdb - Twb )

lda
Ti + Twb
or Tdb =
2
IES-19. In case A, moist air is adiabatically saturated and in case B, moist air is
vi
isobarically saturated. The saturation temperatures in cases A and B are

respectively [IES-2002]
(a) dry bulb temperature and wet bulb temperature
(b) dew point temperature and wet bulb temperature
Ci
(c) wet bulb temperature and dew point temperature

(d) wet bulb temperature and dry bulb temperature
IES-19Ans. (c)
w.
IES-20. When the wet bulb and dry bulb temperatures are equal, which of the following
statements is/are correct? [IES-2005]
1. Air is fully saturated.
2. Dew point temperature is reached.
3. Partial pressure of vapour equals to the total pressure.
ww
4. Humidity ratio is 100%.

(a) 1 and 2 (b) 1 only (c) 1, 2 and 4 (d) 2 and 3
IES-20Ans. (a) In case the relative humidity of air is 100% (saturated air) then
Dry bulb temperature
wet bulb temperature
dew point temperature
Saturation temperature will be equal
IES-21. When the wet and dry bulb temperatures are identical, which of the
following statements is/are true? [IES-2001; 2003]
1. Air is fully saturated
2. Dew point temperature is reached
Page 92 of 128
Psychrometry
3. Humidity ratio is unity
4. A Partial pressure of vapour equals total pressure
(a) 1 only (b) 1 and 2 (c) 3 and 4 (d) 1, 2, 3 and 4
IES-21Ans. (b)
IES-22. When dry-bulb and wet-bulb temperatures are identical, it means that the
(a) air is fully saturated and dew-point temperature has reached [IES-2000]
(b) air is fully saturated
m
(c) dew-point temperature has reached and humidity is 100%
(d) partial pressure of water vapour is equal to total pressure
IES-22Ans. (a)
.co
IES-23. At 100% relative humidity, the wet bulb temperature is [IES-1995]
(a) more than dew point temperature (b) same as dew point temperature
(c) less than dew point temperature (d) equal to ambient temperature.
IES-23Ans. (b)
IES-24.
tas
In a saturated air-water vapour mixture, the
(a) dry bulb temperature is higher than the wet bulb temperature
(b) dew point temperature is lower than the wet bulb temperature
(c) dry bulb, wet bulb and dew point temperatures are the same
[IES-1993]
lda
(d) dry bulb temperature is higher than the dew point temperature
IES-24Ans. (c) In a saturated air-water vapour mixture, the dry bulb, wet bulb and dew point
temperatures are the same.
vi
Adiabatic saturation of air and adiabatic saturation

temperature
IES-25. During adiabatic saturation process of air, wet bulb temperature [IES-1999]
Ci
(a) increases and dry bulb temperature remains constant

(b) remains constant and dry bulb temperature increases
(c) remains constant and dry bulb temperature decreases
(d) decreases and dry bulb temperature remains constant
w.
IES-25Ans. (c)
IES-26. During the adiabatic cooling of moist air [IES-1996]

(a) DBT remains constant (b) specific humidity remains constant.
ww
(c) relative humidity remains constant (d) WBT remains constant.

IES-26Ans. (d) During the adiabatic cooling of moist air, wet bulb temperature remains
constant
Psychrometric Chart
In a Psychrometric chart
1. vertical lines indicate wet bulb temperature.
2. horizontal lines indicate specific humidity.
3. sensible heating or cooling is represented by an inclined line.
Page 93 of 128
Psychrometry
(a) 1 only (b) 2 only (c) 3 only (d) 1, 2 and 3
IES-27Ans. (b)
m
.co
IES-28. On a Psychrometric chart, what does a vertical downward line represent?
(a) Adiabatic saturation
(c) Dehumidification
IES-28Ans. (c)
IES-29.
tas
(b) Sensible cooling
(d) Humidification
[IES-2008]
Which of the following properties decrease(s) with sensible heating of air-

lda
water vapour mixture? [IES-2008]
1. Relative humidity
2. Humidity ratio
3. Specific enthalpy of air-vapour mixture
4. Wet bulb temperature
vi

(a) 1 only (b) 1 and 3 (c) 2 and 3 (d) 2 and 4
IES-29Ans. (a)
Ci
w.
ww
Sensible heating process on psychrometric chart
IES-30. Moist air is a mixture of dry air and water vapour. Hence three independent
intrinsic thermodynamic properties are required to fix its thermodynamic
state. While using Psychrometric chart, however, only two thermodynamic
properties are needed since, Psychrometric chart [IES-1993]
(a) is an approximation to actual properties
(b) assumes that both water vapour and dry air behave like perfect gases
(c) is drawn for actual properties of water vapour and dry air
(d) is drawn for a fixed pressure
Page 94 of 128
Psychrometry
IES-30Ans. (d) The Psychrometric chart is drawn for a fixed pressure (standard atmospheric
pressure) and thus only two thermodynamic properties are needed to fix
thermodynamic state.
IES-31. To fix the state point in respect of air-vapour mixtures, three intrinsic
properties are needed. Yet, the Psychrometric chart requires only two
because [IES-1998]
(a) water vapour is in the superheated state
(b) the chart is for a given pressure
m
(c) the chart is an approximation to true values
(d) the mixtures can be treated as a perfect gas
IES-31Ans. (b) Psychrometric chart is plotted for standard atmospheric pressure and as such
.co
only 2 coordinates are used to fix the state point. For pressures other than standard
atmospheric, some correction is required.

On Psychrometric chart, the constant wet bulb temperature lines coincide
with.
tas
(a) constant relative humidity lines
(b) constant enthalpy lines
(c) constant dew point temperature lines
(d) constant volume lines
IES-32ans. (b)
vi lda
Ci
w.
ww
Page 95 of 128
Psychrometry
m
.co
IES-33. Which one of the
following is correct for
the process 1-2 shown
above?
(a) The partial pressure
of water vapour in air
tas
lda
remains constant
(b) Specific humidity of
air remains constant
(c) Enthalpy of air
remains constant
vi
(d) Dry bulb temperature

of air remains constant
[IES-2006]
Ci
IES-33Ans. (c)
IES-34.
w.
ww
Which one of the following statements is correct for a cooling and

humidification process 1-2 as shown on the psychrometric chart above?
(a) Wbt decreases in the process [IES-2009]
(b) The total enthalpy increases in the process
Page 96 of 128
Psychrometry
(c) The total enthalpy remains constant in the process
(d) It is an adiabatic saturation process
IES-34Ans. (b) We know that during cooling and humidification process, the enthalpy of air
may increase, decrease or remain constant depending upon the temperature of the
wet surface. Here the line diverges from wet bulb temperature line due to total
enthalpy increases in the process.
IES-35. Which of the following properties increasers) during sensible heating of air-
m
water vapour-mixture? [IES-2003]
1. Relative humidity 2. Humidity ratio
3. Wet bulb temperature 4. Specific enthalpy of air-vapour
.co
mixture
(a) 1 and 2 (b) 3 only (c) 2 and 3 (d) 3 and 4
IES-35Ans. (d)
tas
lda
IES-36. Atmospheric air at 35°C and 60% RH can be brought to 20°C and 60% RH by:
vi
(a) Cooling and dehumidification process

(b) Cooling and humidification process
(c) Adiabatic saturation process
(d) Sensible cooling process
Ci
IES-36Ans. (a)1-2 = 1-2` + 2`-2

cooling + de-humidification
w.
[IES-2006]
ww

In psychrometry, wet-bulb temperature is a measure of enthalpy of moist
air, so that in the Psychrometric chart,
1. the constant enthalpy lines are also constant wet bulb temperature lines
2. the wet bulb and dry bulb temperature are same at any condition
3. the wet - bulb and dry-bulb temperature are equal at saturation
condition.
Of these statements.
(a) 1 alone is correct (b) 1 and 2 are correct
(c) 1 and 3 are correct (d) 2 and 3 are correct.
IES-37Ans. (c)
Page 97 of 128
Psychrometry

(a) Pressure and temperature are independent during phase change.
(b) An isothermal line is also a constant pressure line in the wet vapour region.
(c) Entropy decreases during evaporation.
(d) The term dryness fraction is used to specify the fraction by mass of liquid in a
mixture of liquid and vapour.
IES-38Ans. (b)
m
IES-39. In a psychrometric chart, what does a vertical downward line represent?
(a) Sensible cooling process (b) Adiabatic saturation process
(c) Humidification process (d) Dehumidification process [IES-2009]
.co
IES-39Ans. (d)
Basic Processes in Conditioning of Air

Sensible heating
IES-40. Consider the following statements:
During sensible heating
1. moisture content increases
temperature increase
tas [IES-1994]
2. dry bulb temperature and wet bulb

lda
3. dew point remains constant 4. relative humidity increases
(a) 1, 2 and 3 (b) 2,3 and 4 (c) 2 and 3 (d) 1 and 2
IES-40Ans. (c) During sensible heating, dry bulb temperature and wet bulb temperature
increase, dew point remains unchanged. Moisture content remains same and relative
humidity decreases. This statements 2 and 3 are correct
vi
IES-41. Consider the following statements regarding Psychrometric processes:

1. Sensible heating is a process in which moisture content remains
unchanged.
Ci
2. In the dehumidification process the dew point temperature remains

same.
3. The process of adding moisture at constant dry bulb temperature is
known as pure humidification process.
w.
Which of the statements given above is/are correct? [IES-2008]

(a) 1 and 2 (b) 1 and 3 (c) 2 and 3 (d) 1 only
IES-41Ans. (b) In the dehumidification process the dew point temperature decreases.

ww
In a sensible heating or cooling process

(a) dry bulb temperature remains constant
(b) wet bulb temperature remains constant
(c) the humidity ratio remains constant
(d) the relative humidity remains constant
IES-42Ans. (c)
Page 98 of 128
Psychrometry
m
Sensible Heat Process-Heating or Cooling
.co
IES-43. Match List-I with List-II and select the correct answer using the code given
below the lists: [IES-2008]
List I (Devices) List II (Process undergone by air)
A. Cooling tower 1. Heating
B. Air coolers 2. Cooling and dehumidification
C. Evaporator coil 3. Cooling and humidification
D. Air cooled condenser
Code:
(a)
(b)
(c)
A
2
4
2
B
1
3
3
C
4
2
4
D
3
1
1
tas
4. Heating and humidification
lda
(d) 4 1 2 3
IES-43Ans. (b)Cooling tower → Heating and humidification
Air coolers → Cooling and humidification
Evaporator coil → Cooling and dehumidification
Air cooled condenser → Heating
vi
Sensible cooling
Ci
IES-44. During sensible cooling of air, [IES-1998]

(a) its wet bulb temperature increases and dew point remains constant
(b) its wet bulb temperature decreases and the dew point remains constant
(c) its wet bulb temperature increases and the dew point decreases
w.
(d) its wet bulb temperature decreases and dew point increases
IES-44Ans. (b) During sensible cooling of air, its wet bulb temperature decreases but dew point
remains unchanged.
IES-45. During sensible cooling [IES-1992]

ww
(a) Relative humidity remains constant

(b) Wet bulb temperature increases
(c) Specific humidity increases
(d) Partial pressure of vapour remains constant.
IES-45Ans. (d)

During sensible cooling of moist air, its relative humidity
(a) increases (b) does not change
(c) decreases (d) affects specific humidity
IES-46Ans. (a)
Page 99 of 128
Psychrometry
m
.co
Humidification
Dehumidification
IES-47. When warm saturated air is cooled
tas [IES-2000]
lda
(a) excess moisture condenses
(b) excess moisture condenses but relative humidity remains unchanged
(c) excess moisture condenses and specific humidity increases but relative humidity
remains unchanged.
(d) specific humidity increases and relative humidity decreases
IES-47.Ans. (b) RH 100% constant remains.
vi
IES-48.
Ci
w.
ww
A classroom is to be air-conditioned by obtaining the comfort conditions of

22°C dbt and 55% RH from outdoor conditions of 32°C dbt and 22°C wbt.
The weight of outside air supplied is 30 kg/min. The comfort conditions
required are achieved first by chemical dehumidification and then by
cooling with a cooling coil as shown in the psychrometric chart above. What
is the capacity of the dehumidification in kg/hr? [IES-2009]
(a) 3.2 (b) 5.4 (c) 6.8 (d) 9.5
IES-48Ans. (b)Capacity of dehumidification in kg hour
= m × ( ω1 − ω2 )
= ( 30 × 60 )(12.6 − 9.6 ) × 10−3 = 5.4 kg / hour
Page 100 of 128
Psychrometry
Chemical Dehumidification
In chemical dehumidification process
1. dew point temperature decreases.
2. wet bulb temperature decreases
3. dry bulb temperature increases.
Of these statements
m
(a) 1, 2 and 3 are correct (b) 1 and 2 are correct
IES-49Ans. (d) The absorption of water
.co
by the hygroscopic material is
an exothermic reaction, as a
result heat is released during
this process, which is
transferred to air and the
enthalpy of air increases.
tas
lda
IES-50. If air is passed through a solid chemical absorbent, the Psychrometric
process followed is [IES-1992]
(a) heating and dehumidification with the wet bulb temperature remaining fairly
constant
vi
(b) cooling and dehumidification

(c) dehumidification with sharp rise in wet bulb temperature
(d) dehumidification at constant dry bulb temperature.
IES-50.Ans. (a)
Ci
Cooling and dehumidification

w.
IES-51. Air at 35°C DBT and 25°C dew point temperature passes through the water
shower whose temperature is maintained at 20°C. What is the process
involved? [IES-2004]
(a) Cooling and humidification (b) Sensible cooling
(c) Cooling and dehumidification (d) Heating and humidification
ww
IES-51Ans. (c)As temp of shower (200C) is below DBT (350C) sensible cooling will occur.
As temp of the shower (200C) is below Dew point temp (250C) some moisture of will
condensed and form water droplets i.e. dehumidification.
IES-52. For cooling and dehumidifying of unsaturated moist air, it must be passed
over a coil at a temperature [IES-2002]
(a) of adiabatic saturation of incoming stream
(b) which is lower than the dew point of incoming stream
(c) which lies between dry bulb and wet bulb temperature
(d) which lies between wet bulb and dew point temperature of incoming stream
IES-52Ans. (b)
Page 101 of 128
Psychrometry
Cooling and humidification

IES-53. Assertion (A): During cooling with humidification dew point decreases.
Reason (R): The process results in increased specific humidity. [IES-1992]
m
IES-53Ans. (d)
IES-54. When the air is passed through an insulated chamber having sprays of
.co
water maintained at a temperature higher than the dew point temperature
of entering air but lower than its dry bulb temperature, then the air is said
to be [IES-1994]
(a) cooled and humidified (b) cooled and dehumidified
(c) heated and humidified (d) heated and dehumidified
tas
IES-54.Ans. (a) When air is passed through spray of water at temperature higher than dew
point temperature of entering air and lower than its dry bulb temperature, then air is
cooled and humidified.
lda
Heating and dehumidification
Sensible heat factor (SHF)
vi
IES-55. The sensible heat factor of a room is given by (S.H.L = Sensible heat load
and L.H.L. = Latent heat load) [IES-1999]
S .H .L − L.H .L S .H .L S .H .L + L.H .L S .H .L
(a ) (b) (c) (d )
Ci
S .H .L S .H .L − L.H .L S .H .L S .H .L + L.H .L
S .H .L
IES-55Ans. (d) SHF =
S .H .L + L.H .L
w.
IES-56. What is the sensible heat factor during the heating and humidification
process equal to? [IES-2006]
ww
H1 + H 2 H 2 − H1 H1 + H 2 H 3 + H1
(a) (b) (c) (d)
H 3 − H1 H 3 − H1 H1 − H 2 H 2 − H1
Where, H1= Total heat of air entering the heating coil
H2 = Total heat of air leaving the heating coil
H3 = Total heat of air at the end of the humidification
IES-56.Ans. (d)
IES-57. The latent heat load in an auditorium is 25% of the sensible heat load. The
value of sensible heat factor (S H F) is equal to [IES-2002]
(a) 0.25 (b) 0.5 (c) 0.8 (d) 1.0
IES-57Ans. (c)
Page 102 of 128
Psychrometry
IES-58. In a Psychrometric process, the sensible heat added is 30 kJ/sec and the
latent heat added is 20 kJ/sec. The sensible heat factor for the process will
be [IES-1993]
(a) 0.3 (b) 0.6 (c) 0.67 (d) 1.5
sensible heat 30
IES-58.Ans. (b) Sensible heat factor = = = 0.6
sensible heat + latent heat 30 + 20
m
Psychrometric Processes in Air Conditioning
Equipment
.co
Bypass factor
IES-59. Atmospheric air at dry bulb temperature of 15°C enters a heating coil whose
surface temperature is maintained at 40oC. The air leaves the heating coil at
25°C. What will be the by-pass factor of the heating coil? [IES-2004]
(a) 0.376
IES-59.Ans. (c)
IES-60.
(b) 0.4
tas
(c) 0.6 (d) 0.67
In order to have a low bypass factor of a cooling coil, the fin spacing and the
number of tube rows should be: [IES-1998; 2005]
lda
(a) Wide apart and high, respectively (b) Wide apart and low, respectively
(c) Close and high, respectively (d) Close and low, respectively
IES-60Ans. (c)
IES-61. Air is 20°C dry bulb temperature and 40% relative humidity is heated upon
40°C using an electric heater, whose surface temperature is maintained
vi
uniformly at 45°C. The bypass factor of the heater is [IES-1999]

(a) 0.20 (b) 0.25 (c) 0.88 (d) 1
t3 − t2 45 − 40
IES-61Ans. (a) Bypass factor = = =0.2
Ci
t3 − t1 45 − 20
IES-62. The atmosphere air at dry bulb temperature of 15°C enters a heating coil
maintained at 40°C. The air leaves the heating coil at 25°C. The bypass
w.
factor of the heating coil is [IES-1994]

(a) 0.375 (b) 0.4 (c) 0.6 (d) 0.67
40 − 25
IES-62.Ans. (c) Bypass factor of heating coil = = 0.6
40 − 15
ww
IES-63. In the case of sensible cooling of air, the coil efficiency is given by (BPF =
Bypass factor) [IES-1993]
(a) BPF-1 (b) 1-BPF (c) BPF (d) 1 + BPF
IES-63Ans. (b) Coil efficiency in the sensible cooling is = 1 - BPF
IES-64. The by-pass factor of single cooling coil in an air-conditioner is 0.7. The by-
pass factor, if three such cooling coils with the same apparatus dew point
are kept one behind the other will be
(a) 0.210 (b) 0.292 (c) 0.343 (d) 0.412 [IES-2001]
IES-65Ans. (c) Let us take an example t3 − t1 = 100o C
First coil will reduce 30 oC Then only 70 oC left for next two coil
Page 103 of 128
Psychrometry
Second coil will reduce 30% of 70 oC i.e. 21 oC . Then only 49 oC left for third coil
Third coil will reduce 30% of 49 oC i.e. equal to 14.7 oC
Therefore total by pass = (100 – 30 – 21 – 14.7 ) = 34.3 oC
34.3
So BPF = = 0.343
100
IES-66. By pass factor for a cooling coil [IES-1992]

(a) increases with increase in velocity of air passing through it
(b) decrease with increase in velocity of air passing through it
m
(c) remains unchanged with increase in velocity of air passing through it
(d) may increase or decrease with increase in velocity of air passing through it
depending upon the condition of air entering.
.co
IES-66Ans. (a)
Heating Coil
IES-67. The atmospheric air at 760 mm of Hg, dry bulb temperature 15°C and wet
(a) 28°C (b) 29°C

tas
bulb temperature 11 C enters a heating coil whose temperature is 41°C. If
the by-pass factor of the heating coil is 0.5, then what will be the dry bulb
temperature of the air leaving the coil?
(c) 30°C
IES-67Ans. (a)Let the D.B.T of leaving coil = T°C

(d) 26°C
[IES-2009]
vi lda
Temperature = 41°C
41 − T
= 0.5
Ci
41 − 15
⇒ 41 − Τ = 13
⇒ T = 28°C
Air Washer
w.

Air washer can work as
1. Humidifier only
2. Dehumidifier only
ww
3. Filter only
(a) Only 1 (b) Only 2 and 3 (c) Only 1 and 3 (d) 1, 2 and 3
IES-68Ans. (d)
IES-69. Air at dry bulb temperature of 35°C and dew point temperature of 25°C
passes through an air washer whose temperature is maintained at 20°C.
What is the nature of the process involved? [IES-2005]
(a) Cooling and humidification (b) Sensible cooling
(c) Heating and dehumidification (d) Cooling and dehumidification
IES-69Ans. (d)
Page 104 of 128
Psychrometry
IES-70. In a spray washing system, if the temperature of water is higher than the
dry bulb temperature of entering air, then the air is [IES-1993]
(a) heated and dehumidified (b) heated and humidified
(c) cooled and humidified (d) cooled and. dehumidified
IES-70Ans. (b)
Air Conditioning
m
IES-71. For an air-conditioned space, RTH = 100 kW, RSHF = 0.75, volume flow rate
= 100m3/min, and indoor design specific humidity is 0.01 kg/kg of dry air.
What is the specific humidity of the supply air? [IES-2001; 2005]
.co
(a) 0.010 (b) 0.0075 (c) 0.005 (d) 0.0025
RLH 25
IES-71.Ans.(c) ( Cmm )s,min = or 100 = or (ωi − 0.01) = 0.005
50 (ωi − ωADP ) 50 (ωi − 0.01)
⎡ RSH RSH ⎤
⎢∵ RSHF = RTH = RSH + RLH ⎥
IES-72.
⎣
(a) 1/2
IES-72Ans. (d)
(b) 3/2
⎦
(c) 9/2
tas
Fresh air intake (air change per hour) recommended for ventilation
purposes in the air-conditioning system of an office building is
(d) 25/2
[IES-1997]
lda
IES-73. Air-conditioning has to be done for a hall whose RSH = 50 kW and RLH = 50
kW. There are no other sources of heat addition or leakages. What is the
value of the RSHF? [IES-2005]
(a) 0.25 (b) 0.5 (c) 0.75 (d) 1.00
vi
RSH 50
IES-73Ans. (b) RSHF = = = 0.5
RSH + RLH 50 + 50
IES-74. Assertion (A): Dehumidification and humidification respectively are needed in
winter and summer air-conditioning. [IES-1994]
Ci
Reason (R): In winter, the air is to be heated and in summer, the air is to be cooled
and moisture control is necessary to maintain the relative humidity within limits.
w.

IES-74.Ans. (a) Both A and R are true and R provides correct explanation for A.
ww
Previous 20-Years IAS Answer

0.622 pv
IAS-1. The expression , where Pv = partial pressure of water vapour;
pb − pv
Pb= atmospheric barometric pressure, is used for calculating [IAS-2001]
Page 105 of 128
Psychrometry
(a) relative humidity (b) degree of saturation
(c) humidity ratio (d) pressure of air
pv
IAS-1Ans. (c) Specific humidity or absolute humidity or humidity ratio (w) = 0.622 ×
pb − pv
IAS-2. Moist air exists at a pressure of 1.01 bar. The partial pressure and
saturation pressure of water vapour are 0.01 bar and 0.02 bar respectively.
What are the relative humidity and humidity ratio of the moist air,
m
respectively? [IAS-2004]
(a) 50% and 0.00622 (b) 100% and 0.0126
(c) 50% and 0.0126 (d) 100%and 0.00622
PV 0.01
IAS-2.Ans. (a) relative humidity ( Q ) =
.co
× 100% = × 100% = 50%
PS 0.02
P 0.01
Specific humidity ( μ ) = 0.622 V = 0.622 × = 0.00622
Pb − Pv 1.01 − 0.01
Relative humidity
IAS-3.
tas
If a sample of moist air of 50% relative humidity at atmospheric pressure is
lda
isothermally compressed to a pressure of two atmospheres, then
[IAS-1999]
(a) its relative humidity will reduce to 25%
(b) its relative humidity will remain unchanged
(c) the sample of air will become saturated
(d) saturation pressure will increase to twice the value
vi
IAS-3.Ans. (c)
IAS-4. For which one of the following DBT, WBT and DPT has the same value?
(a) 0 per cent relative humidity line (b) 100 per cent relative humidity line
Ci
(c) 50 per cent relative humidity line (d) None of the above [IAS-2007]
IAS-4Ans. (b)
IAS-5. Match List I (Quantity) with List II (Measuring Device) and select the
w.
correct answer using the codes given below the Lists: [IAS-2002]
List I List II
(Quantity) (Measuring Device)
A. Engine speed 1. Manometer
ww
B. Fuel heating value 2. Tachometer

C. Air velocity 3. Hydrometer
D. Relative humidity of air 4. Calorimeter
5. Hygrometer
(a) 2 5 1 4 (b) 1 5 3 4
(c) 2 4 1 5 (d) 1 4 3 5
IAS-5Ans. (c)
Page 106 of 128
Psychrometry
IAS-6. A sample of moist air is at a temperature T and relative humidity 50%.Apart
of the moisture is removed adiabatically by using an adsorbent. If the heat
of adsorption is negligible, the resulting air will have the same [IAS-1998]
(a) dry bulb temperature but a lower wet bulb temperature
(b) wet bulb temperature but a higher dry bulb temperature
(c) dry bulb temperature but a higher wet bulb temperature
(d) wet bulb temperature but a lower dry bulb temperature
IAS-6.Ans. (b)
m
IAS-7. Evaporative regulation of body temperature fails when the body temperature is
(a) more than wet bulb temperature but less than dry bulb temperature
.co
(b) more than dew point but less than wet bulb temperature
(c) more than dew point but less than dry bulb temperature [IAS-1999]
(d) less than dew point
IAS-7Ans. (d)
IAS-8.
tas
Consider the following statements: [IAS-1995]
1. Dew point is reached by cooling air at constant moisture content.
2. Wet bulb temperature changes by addition of moisture at constant
enthalpy.
3. For saturated air, the dry bulb temperature, wet bulb temperature and
lda
dew point are the same.
4. Dehumidification of air is achieved by heating.
(c) 3 and 4 are correct (d) 1 alone is correct
IAS-8.Ans. (a)
vi
Degree of saturation
Ci
IAS-9. The ratio of weight of water vapour associated with unit weight of dry air to
the weight of water vapour associated with unit weight of dry air saturated
at the same dry-bulb temperature and pressure is known as [IAS-2000]
(a) specific humidity (b) relative humidity
(c) absolute humidity (d) degree of saturation
w.
IAS-9Ans. (d)
Wet Bulb Temperature (WBT)

ww
IAS-10. If wet bulb depression is equal to the sum of range and approach of a
cooling tower, then the water [IAS-1999]
(a) inlet temperature is equal to the wet bulb temperature of ambient air.
(b) outlet temperature is equal to the wet bulb temperature of ambient air.
(c) inlet temperature is equal to dry bulb temperature of ambient air.
(d) outlet temperature is equal to dry bulb temperature of ambient air.
IAS-10Ans. (c)

If moist air is adiabatically saturated in an air washer than
1.wet bulb temperature remains constant
Page 107 of 128
Psychrometry
2.relative humidity increases
3.dry bulb temperature decreases
4.humidity ratio decreases
(a) 1, 2 and 3 (b) 1, 2 and 4 (c) 2, 3 and 4 (d) 1, 3 and 4
IAS-11Ans. (a)
IAS-12. If the measured wet-bulb temperature and the thermodynamic wet-bulb

temperature are equal then the non-dimensional number with a value of
m
unity is the [IAS-2000]
(a) Lewis number (b) Prandtl number (c) Schmidt number (d) Sherwood number
IAS-12Ans. (a) Le = 0.945
.co
Adiabatic saturation of air and adiabatic saturation
temperature
IAS-13.
(a) 2.50 C (b) 3.00 C

IAS-13Ans. (c) Heat balance gives us
tas
Water in an insulated evaporative cooler evaporates at the rate of 0.003 kg/s.
Air flow rate is 1kg/s. What is the air temperature decrease if the specific
heat of humid air is 1kJ/kg K and latent heat of water is 2500 kJ/kg?
(c) 7.50 C (d)100C [IAS-2004]
lda
ma c p ΔT = mw × L
mw × L 0.003 × 2500
or ΔT = = = 7.50 C
ma × c p 1× 1
IAS-14. Total heat transfer from a wetted surface depends upon [IAS-2003]
(a) difference in temperature between surface and air
vi
(b) difference in humidity ratio of air and air saturated at wet surface temperature
(c) difference in enthalpy between saturated air at surface temperature and that of
air
Ci
(d) difference in entropy between saturated air at surface temperature and that of air
IAS-14Ans. (d) spontaneous process.
IAS-15. The main process which takes place in a desert-cooler is [IAS-2001]

(a) sensible cooling (b) dehumidification
w.
(c) adiabatic saturation (d) cooling and dehumidification

IAS-15Ans. (c) In a desert-cooler water vaporize and latent heat of vaporization is cools the
air. i.e. cooling and humidification.
ww
IAS-16. Desert coolers are suitable for hot very dry outside conditions because
(a) water is recirculated in the spray [IAS 1994]
(b) heat is neither added nor removed from the water
(c) wet bulb depression (t-t) is very large
(d) large quantity of air can be conditioned
IAS-16Ans. (c)
Page 108 of 128
Psychrometry
Psychrometric Chart
IAS-17. With respect to the following figure which shows four processes on the
Psychrometric chart, match List I with List II and select the correct answer
using the codes given below the lists: [IAS-1996]
List I List II
A. Process RS 1. Cooling and humidifying
B. Process RT 2. Sensible heating
m
C. Process RU 3. Cooling and dehumidifying
D. Process RW 4. Humidifying
(a) 2 3 1 4 (b) 1 4 2 3
.co
(c) 3 1 4 2 (d) 3 2 1 4
IAS-17Ans. (c)
IAS-18. Assertion (A): On the Psychrometric chart, constant enthalpy lines and constant
wet bulb lines are the same. [IAS-1995]
tas
Reason (R): For the same wet bulb temperature, the moisture content remains
constant.
lda
IAS-18Ans. (c)
Basic Processes in Conditioning of Air

vi
Sensible heating
Ci

List I List II
A. Steam spray into air 1. Sensible cooling
B. Air passing over a coil 2. Cooling and dehumidification
w.
carrying steam
C. Air passing over coil having 3. Heating and humidification
temperature less than dew point 4. Sensible heating
D. Air passing over a coil having
ww
Temperature above the dew point

but below the wbt
(a) 2 1 3 4 (b) 3 1 2 4
(c) 3 4 2 1 (d) 4 3 2 1
IAS-19Ans. (c)
IAS-20. When moist air comes into contact with a wetted surface whose
temperature is less than the dry-bulb temperature but more than the wet-
bulb temperature? [IAS-2000]
(a) sensible, latent and net heat transfers are from air to surface
Page 109 of 128
Psychrometry
(b)both sensible and net heat transfers are from air to surface but latent heat
transfer is from surface to air
(c)sensible heat transfer is from air to surface but both latent and net heat transfers
are from surface to air
(d) sensible heat transfer is from surface to air but both latent and net heat transfers
are from air to surface.
IAS-20Ans. (b)
Sensible cooling
m
IAS-21. If moist air is sensibly cooled above its dew point, which of the following
statements are correct? [IAS-2004]
1. Relative humidity decreases. 2. Wet bulb temperature decreases.
.co
3. Wet bulb temperature increases.4. Humidity ratio remains constant.
Codes:
(a) 1 and 2 (b) 1and 3 (c) 3 and 4 (d) 2 and 4
IAS-21Ans. (d)
IAS-22. During chemical dehumidification

tas
(a) wet bulb temperature constant but enthalpy changes
(b) dry bulb temperature remains constant
(c) both dew point and we bulb temperature remain constant
[IAS-1996]
lda
(d) enthalpy and web bulb temperature remain constant
IAS-22Ans. (d) But WBT will increases.
IAS-23. Which one of the following statement is correct? [IAS-2003]

(a) Dehumidifier coil surface temperature is above both the dew point temperature
but below the freezing point temperature
vi
(b) Dehumidifier coil surface temperature is below the dew point temperature but
above the freezing point temperature
(c) Dehumidifier coil surface temperature is below the dew point temperature and the
Ci
freezing point temperature

(d) Dehumidifier coil surface temperature is above the dew point temperature and
the freezing point temperature
IAS-23Ans. (b)
w.
Heating and humidification

IAS-24. In summer air-conditioning, the conditioned air passing through the space
undergoes a process of [IAS-1998]
ww
(a) sensible cooling (b) sensible heating

(c) cooling and dehumidification (d) heating and humidification
IAS-24Ans. (d)
IAS-25. The process in a hot water spray washer maintained at a temperature of

400C, through which unsaturated air at 10° C dry bulb temperature and 50%
relative humidity passes, is [IAS-1997]
(a) sensible heating (b) humidification
(c) heating and humidification (d) heating and dehumidification
IAS-25Ans. (c)
Page 110 of 128
Psychrometry
Cooling and dehumidification
IAS-26. It is desired to condition the outside air from 70% RH and 45°C dry bulb to
50% RH and 25°C dry bulb room condition. The practical arrangement
would be [IAS 1994]
(a) cooling and dehumidification (b) dehumidification and pure sensible cooling,
(c) cooling and humidification (d) dehumidification
IAS-26Ans. (a)
m
IAS-27. To cool and dehumidify a stream of moist air, it must be passed over the coil
at a temperature [IAS-1995]
(a) which lies between the dry bulb and wet bulb temperatures of the incoming
.co
stream
(b) which lies between the wet bulb and dew point temperature of the incoming
stream
(c) which is lower than the dew point temperature of the incoming stream
(d) of adiabatic saturation of incoming steam
IAS-27Ans. (c)
Cooling and humidification

IAS-28.
tas
A cooling coil with a bypass factor of 0.1 and apparatus dew point (adp) of
12°C comes in contact with air having a dry-bulb temperature of 38° C and
lda
dew point of 9° C. Over the cooling coil, the air would undergo [IAS-2001]
(a) sensible cooling (b) cooling and humidification
(c) cooling and dehumidification (d) adiabatic saturation
IAS-28Ans. (b) Apparatus due point = 120C
∴ minimum temperature expected = 12 × (1 − 0.1) = 10.80 C
vi
So the process is cooling and humidification as 90C is lower than 10.80C
IAS-29. If air at dry-bulb temperature of 35° C and dew point temperature of 20° C
passes through a cooling coil which is maintained at 25° C, then the process
Ci
would be [IAS-1997]
(a) sensible cooling (b) cooling and dehumidification
(c) cooling and humidification (d)cooling at constant wet bulb temperature
IAS-29Ans. (c)
w.
IAS-30. In order to cool and dehumidify a stream of moist air, it must be passed
over a coil at a temperature [IAS-2004]
(a) which lies between the dry bulb and wet bulb temperatures of the incoming
stream
ww
(b) which lies between the wet bulb and dew point temperatures of the incoming
stream
(c) which is lower than the dew point temperature of the incoming stream
(d) of adiabatic saturation of incoming stream
IAS-30.Ans. (c)
Page 111 of 128
Psychrometry
Heating and dehumidification
Sensible heat factor (SHF)
IAS-31. In an air-conditioning process, 5kJ/min heat is extracted from a room. If the
sensible heat factor is 0.8, then the latent heat extracted will be [IAS-1997]
(a) 4 kJ/min (b) 2 kJ/min (c) 1 kJ/min (d) 0.25 kJ/min
SH SH
IAS-31Ans. (c) SHF = or 0.8 = or SH = 4 kJ / min, LH = 1 kJ / min
m
SH + LH 5
IAS-32. In an auditorium, the heat generated due to the occupants and the electric
lights and other equipments is 100 kW. The rate of generation of excess
.co
moisture is 60kg/hr. If an air-conditioner is supplying conditioned air to the
auditorium at the rate of 500 m3/min, then the sensible heat factor (SHF) for
the auditorium is [IAS 1994]
(a) 0.27 (b) 0.40 (c) 0.73 (d) 0.95
IAS-32Ans. (c)
Psychrometric Processes in Air Conditioning

Equipment
tas
lda
Bypass factor
IAS-33. Assertion (A): Bypass factor of a cooling coil decreases with decrease in face velocity.
Reason (R): Air gets more time to contact the cooling coil at lower face velocity.
vi
(d) A is false but R is true [IAS-2003]
Ci
IAS-33Ans. (b)
IAS-34. The condition of air for a cooling

and dehumidification system is
given by th point A at intake, B
w.
at discharge as marked on a
Psychrometric chart. It C is the
apparatus dew point, the
bypass factor is given by
ww
CA CA BC BC
(a ) (b) (c ) (d )
AB BC AB CA [IAS-1996]
IAS-34Ans. (d)
IAS-35. Consider the following statements [IAS 1994]

1. Low value of the bypass factor for an air-conditioning equipment signifies
higher performance of the equipment
2. Bypass factor for an air-conditioning equipment signifies the fraction of
ambient air mixed with the air to be conditioned.
3. Bypass factor for an air-conditioning equipment signifies the fraction of
the air to be conditioned coming in contact with the conditioning surface.
Page 112 of 128
Psychrometry
(a) I and III are correct (b) I and II are correct
(c) III alone is correct (d) II alone is correct
IAS-35Ans. (b)
Air Washer
IAS-36. Two steams moist air ‘1’and ‘2’mix together stream of unsaturated air ‘3’, Let
‘m’ denote the rate of total mass flow of moist air, ‘m ω ’denote the rate of
m
mass flow of associated water vapour, ‘ ω ’denote the specific humidity and
‘t’ the temperature of a stream. Then ‘t3’ the temperature of stream ‘3’ will
be [IAS-1995]
( m1 − mω 2 )ω1t1 + ( m2 − mw2 ) ω2t2 ( m1 − mω 2 ) t1 + ( m2 − mw 2 ) t2
.co
(a) (b)
( m3 − mω 3 )ω3 ( m3 − mω1 )
ω1t1 + ω2t2 m1ω1t1 + m2ω2t2
(c) (d)
ω2 m2ω3
IAS-36Ans. (b)
Air Conditioning
IAS-37. Consider the following statements:
tas
1. If air is heated in a closed chamber, its dew point will increase
[IAS-2000]
lda
2 As relative humidity decreases, the difference between the wet-bulb
temperature and dew point will increase
3. In spray humidification process, the enthalpy of air will decrease
4. The dew-point temperature is always an indication of moisture content of
the air
vi

(a) 1 and 2 (b) 2 and 4 (c)1 and 3 (d) 3 and 4
IAS-37 Ans. (b)
1. As no moisture is added so no change in dew point.
Ci
2. (tw1 – td1) < (tw2 – td2)

w.
ww
3. By energy balance it increases not decreases because it added water’s enthalpy h2

= h1 + (ω2 − ω1 ) hf
4. See above graph
So 2 & 4 are correct

When a GSHF line is extended, it may strike the saturation curve at a point.
This point is called
1. effective surface temperature. 2. air saturation temperature.
Page 113 of 128
Psychrometry
3. water boiling temperature. 4. apparatus dew point.
IAS-38Ans. (b)
IAS-39. In the case of a cooling coil with non-zero bypass factor, the apparatus, dew
point temperature lies at the intersection point of [IAS-1997]
(a) room DB line with the saturation curve
(b) RSHF and GSHF lines
m
(c) RSHF and ESHF lines
(d) GSHF line with the saturation curve
IAS-39Ans. (d)
.co
IAS-40. The state of air supplied by a cooling coil with a by-pass factor X lies on the
Psychrometric chart at the [IAS-1998]
(a) intersection of RSHF line with saturation curve
(b) intersection of GSHF line with saturation curve
(c) point which divides RSHF line in proportion to X and (1 - X)
IAS-41.
tas
(d) point which divides ESHF line in proportion to X and (I-X)
IAS-40Ans. (d)
Consider the following statements related to all-air air-conditioning system:

1.All air system uses air as heating or cooling fluid. [IAS-2007]
lda
2.When hot air is circulated through rooms, dehumidification is necessary
to control relative humidity.
3.Return air ducts are required for recirculation.
(a) 1, 2 and 3 (b) 1 and 2 only (c) 1 and 3 only (d) 2 and 3 only
IAS-41Ans. (c)
vi
Ci
w.
ww
Page 114 of 128
Miscellaneous
10. Miscellaneous
m
.co
Load calculation
GATE-1. Atmospheric air at a flow rate of 3 kg/s (on dry basis) enters a cooling and
dehumidifying coil with an enthalpy of 85 kJ/kg of dry air and a humidity
(a) 75.0 (b) 123.8

tas
ratio of 19 grams/kg of dry air. The air leaves the coil with an enthalpy of 43
kJ/kg of dry air and a humidity ratio 8 grams/kg of dry air. If the
condensate water leaves the coil with an enthalpy of 67 kJ/kg, the required
cooling capacity of the coil in kW is
(c) 128.2 (d) 159.0
[GATE-2007]
lda
GATE-1Ans. (c) W1 = 19 gram /kg of dry air
=19 × 10-3 kg / kg of dry air
W2 = 8 gram / kg of dry air
Hence at inlet mass of water vapour
= mv1 = 19 × 10-3 × (3kg / sec)
= 57 × 10-3 kg / sec.
vi
At out let mass of water vapour

Mv1 = 8 × 10-3 × (3 kf / sec)
= 24 × 10-3 kg / sec.
Ci
Hence mass of water condensed

= (57 – 24) ×kg/sec.
Reqd.cooling capacity = change in enthalpy of condensed water +change in enthalpy
of dry air
w.
= (67 KJ / kg) × 33 × 10-3 kg / sec + (85 KJ/ kg) – 43 KJ/kg) × 3 kg

/sec
=128.211 KW
Solar refrigeration
ww
GATE-2. A solar collector receiving solar radiation at the rate of 0.6 kW/m2
transforms it to the internal energy of a fluid at an overall efficiency of 50%.
The fluid heated to 350 K is used to run a heat engine which rejects heat at
313 K. If the heat engine is to deliver 2.5 kW power, then minimum area of
the solar collector required would be [GATE-2004]
(a) 8.33 m2 (b) 16.66 m2 (c) 39.68 m2 (d) 79.36 m2
GATE-2Ans. (d)
Let area be A ∴ heat received(G) = 0.6A kW
and power given to the fluid(Q) = G × ε = 0.6A × 0.5 = 0.3A kW
Page 115 of 128
Miscellaneous
313
Maximum efficiency is Carnot Efficiency (η ) = 1 − = 0.10571
350
Power deliver (W ) = Q × η
Or 2.5 = 0.3A × 0.10571 or A = 79.36m2
Duct Design
Statement for Linked Answer Questions 64 and 65:
An un-insulated air conditioning duct of rectangular cross section 1m x 0.5
m
m, carrying air at 20°C with a velocity of 10 m/s, is exposed to an ambient of
30°C. Neglect the effect of duct construction material. For air n the range of
20-30°C, data are as follows: thermal conductivity = 0.025W/mK: velocity = 18
.co
µPas; Prandtl number = 0.73; density = 1.2 kg/m3. The laminar flow Nusselt
number is 3.4 for constant wall temperature conditions and, for turbulent
flow, Nu = 0.023 Re0.8Pr0.8
GATE-3. The Reynolds number for the flow is [GATE-2005]

(a) 444 (b) 890 (c) 4.44 x 105 (d) 5.33 x 105
GATE-3Ans. (c)
Re =
ρ vD
μ
Or Re =
,
⎡
⎢D =
⎢⎣
4A c 4 × 1× 0.5
P
=
2 (1 + 0.5 )
1.2 × 10 × 0.6667
⎤
= 0.6667 ⎥
= 4.444 × 105
⎥⎦
tas
lda
18 × 10 −6
GATE-4. The heat transfer per metre length of the duct, in watts, is [GATE-2005]
(a) 3.8 (b) 5.3 (c) 89 (d) 769
GATE-4Ans. (d)
Nu = 0.023 × (Re ) × ( 0.73 )
0.8 0.33
vi
= 683.72
hD 683.72 × 0.025
Nu = or h = = 25.64
k 0.6667
Q = hA ( t h − t c ) = 25.64 × 2 × (1 + 0.5 ) × 1× ( 30 − 20 ) = 769 W / m
Ci
Previous 20-Yrs IES Questions

w.
Comfort
IES-1. In a system: Metabolic rate = M, work done by man = W, rate of convective,
ww
radiative and evaporative heat losses = Q and rate of heat storage = S. Then
heat exchange between man and his environment is given by [IES-2002]
(a) M + W = Q + S (b) M - W = Q - S
(c) M + W = Q – S (d) M - W = Q + S
IES-1Ans. (d)
IES-2. A human body feels comfortable when the heat produced by the metabolism
of human body is equal to [IES-1993; 2006]
(a) Heat dissipated to the surroundings
(b) Heat stored in the human body
(c) Sum of (a) and (b)
(d) Difference of (a) and (b)
Page 116 of 128
Miscellaneous
IES-3Ans. (c)
IES-4. A human body feels comfortable when the heat produced due to metabolism
of human body is equal to the [IES-1999]
(a) heat dissipated to the surroundings (b) heat stored in human body
(c) difference between heat dissipated to the surroundings and heat stored in human
body
(d) sum of heat dissipated to the surroundings and heat stored in human body
IES-4Ans. (d)
m
IES-5. A passive method to keep the house comfortably warm by solar
conditioning in cold climatic condition is to paint the: [IES-2005]
.co
(a) Eastern wall of the house by black paint on its outer side
(b) Eastern wall of the house by back paints on its inner side
(c) Southern wall of the house by black paint on its outer side
(d) Southern wall of the house by black paint on its inner side
IES-5Ans. (b)
IES-6.
(a) Temperature only tas

On which factor(s), does the heat lost by the human body in the process of
radiation depend? [IES-2005]
(b) Temperature and air motion
(c) Temperature and relative humidity (d) Relative humidity and air motion
IES-6Ans. (a)
lda
IES-7. Which of the following are normally desired comfort conditions in an air-
conditioning system? [IES-2004]
(a) 25°C DBT and 50% RH (b) 22°C DBT and 90% RH
(c) 15°C DBT and 75% RH (d) 15°C DBT and 40% RH
IES-7Ans. (a)
vi
IES-8. The desirable air velocity in the occupied zone for comfort for summer air-
conditioners is in the range of [IES-2000]
Ci
(a) 6 - 7 m/minute (b) 4 - 5 m/minute (c) 2 - 3 m/minute (d) 0.5 - 1.5 m/minute
IES-8Ans. (a) The recommended comfort conditions for different seasons and clothing suitable
at 50% RNH, air velocity of 0.15 m /s and an activity level of ≤ 1.2 met.
Season Clothing Icl Top,opt Top range for 90%
w.
acceptance
Winter Heavy slacks, long sleeve 0.9 clo 220C 20 to 23.5 0C
shirt and
sweater
Summer Light slacks and short 0.5 clo 24.50C 23 to 260C
ww
sleeve shirt
Minimal (shorts) 0.05 clo 27. 0C 26 to 290C
0.15 m/s = 9 m/minute
IES-9. The reason for a person feeling more comfortable on a warm day if seated in
front of an electric fan is that the [IES-1999]
(a) metabolic heat production is reduced
(b) body loses more heat by convection and evaporation
(c) body loses more heat by radiation
(d) body loses more heat by evaporation and radiation
IES-9Ans. (b)
Page 117 of 128
Miscellaneous
IES-10. On a summer day, a scooter rider feels more comfortable while on the move
than while at a stop light because [IES-1998]
(a) an object in motion captures less solar radiation.
(b) air is transparent to radiation and hence it is cooler than the body.
(c) more heat is lost by convection and radiation while in motion
(d) Air has a low specific heat and hence it is cooler.
IES-10Ans. (c)
IES-11. What are the general comfort conditions in an air-conditioning system?
m
(a) 20oC DBT, 80% RH (b) 24oC DBT, 60% RH [IES-2006]
(c) 25 C DBT, 40% RH
o (d) 25oC DBT, 100% RH
IES-11Ans. (b) ASHARE makes the following recommendations:
.co
Inside design conditions for Winter:
Toptimum between 20.0 to 23.5oC at a RH of 60%
Toptimum between 20.5 to 24.5oC at a DPT of 2oC
Inside design conditions for Summer:
Toptimum between 22.5 to 26.0oC at a RH of 60%
Toptimum between 23.5 to 27.0oC at a DPT of 2oC
IES-12. tas
Which of the following statements are correct? [IES-1994]
1. The human body can lose heat even if its temperature is less than the
atmospheric temperature.
lda
2. Relative humidity can be increased by cooling and dehumidification.
3. Warm air increases the rate of radiation of heat from the human body.
4. Increase in air movement increases the evaporation from the human
body.
Codes:
vi
IES-12Ans. (a)
Effective temperature
Ci
IES-13. The effective temperature is a measure of the combined effects of [IES-1998]

(a) Dry bulb temperature and relative humidity
(b) Dry bulb temperature and air motion
(c) Wet bulb temperature and air motion
w.
(d) Dry bulb temperature, relative humidity and air motion

IES-13Ans. (d) The effective temperature is the combined effect of dry bulb temperature,
relative humidity and air motion.
ww
IES-14. Effective temperature is that temperature of saturated air which gives the
same degree of comfort as the air at given [IES-1993]
(a) DBT, WBT and incidental solar radiation
(b) WBT, incidential solar radiation and air flow rate
(c) DBT, sol-air temperature and air flow rate
(d) DBT, WBT and air flow rate
IES-14Ans. (d)
IES-15. Effective temperature depends on dry bulb temperature, and [IES-2006]

(a) Wet bulb temperature only (b) Relative humidity
(c) Specific humidity (d) Wet bulb temperature and air motion
IES-15Ans. (d)
Page 118 of 128
Miscellaneous
IES-16. Dry bulb temperature and wet bulb temperature is 25°C each, and velocity
of air passing over human body is 6 m/min. If velocity increases to 20 m/min,
then which one of the following is correct? [IES-2006]
(a) The effective temperature decreases
(b) The effective temperature remains the same
(c) The effective temperature increases
(d) The change in effective temperature cannot be estimated with the given
information
m
IES-16Ans. (a) Any activity which increase human comfort will reduce effective temperature.
Alternatively: Rydberg and Norback equation gives us difference
Δ t = (t – 24.4) – 0.1276 (C – 9.1)
.co
t = local temperature, oC; C = local velocity m.p.m
if t is constant and C increases from 6 to 20 m/min
Δ t =– 0.1276 (6 – 20) = - 1.8 oC

The optimum effective temperature for human comfort is:
(c) same in winter and summer

(d) not dependent on season
IES-17Ans. (b)
tas
(a) higher in winter than that in summer
(b) lower in winter than that in summer
lda
(a) Effective temperature is the index which the correlates combined effects of air dry
bulb temperature, air humidity and air movement upon human comfort
(b) The value of effective temperature in winter and summer should be same for
human comfort
vi
(c) Effective temperature and wet bulb temperature are one and the same
(d) The value of effective temperature should be higher in winter than In summer for
comfort
Ci
IES-18Ans. (a)
IES-19. Upon which of the following factors does the effective temperature for
human comfort depend? [IES-2003]
w.
1. Dry bulb temperature 2. Humidity ratio

3. Air velocity 4. Mean radiation temperature
(a) 1 and 2 (b) 1, 3 and 4 (c) 2, 3 and 4 (d) 1, 2, 3 and 4
IES-19Ans. (d) Important factors are the dry bulb temperature, relative humidity, air motion
ww
and surrounding surface temperature. Of these the dry bulb temperature affects heat
transfer by convection and evaporation, the relative humidity affects heat loss by
evaporation, air velocity influences both convective and evaporative heat transfer and
the surrounding surface temperature affects the radiative heat transfer.
IES-20. Consider the following parameters: [IES-2000]

1. Dry-bulb temperature 2. Humidity ratio
3. Air velocity 4. Solar radiation intensity
Which of these parameters are taken into account for determining effective
temperature for human comfort?
(a) 1 and 2 (b) 1 and 4 (c) 2, 3 and 4 (d) 1, 2 and 3
IES-20Ans. (d)
Page 119 of 128
Miscellaneous
IES-21. Assertion (A): Effective temperature, an index of comfort, is defined as that

temperature of saturated air at which one would experience the same feeling of
comfort as experienced in the actual environment. [IES-2001]
Reason (R): Comfort does not depend on humidity and air velocity.
m
IES-21Ans. (c) Comfort depends on dry bulb temp, humidity and air velocity.
Load calculation
.co
IES-22. The heat load from the occupants in air-conditioning load calculation is a
source of: [IES-2006]
(a) Sensible heat only (b) Latent heat only
(c) Both sensible and latent heat (d) None of the above
IES-22Ans. (c)
IES-23.
tas
An air-conditioned room of volume 10 m3 has infiltration of air equivalent to
3 air changes per hour. Density of air is 1.2 kg/m3, specific heat Cp is 1 kJ/kg
K and temperature difference between room and ambient air is 20 K. What
is the sensible heat load due to infiltrated air? [IES-2005]
lda
(a) 60 kJ/hour (b) 12 kJ/hour (c) 0.45 kW (d) 0.2 kW
⎧⎛ 10 × 3 ⎞ ⎫
IES-23Ans. (d) Q = mc p Δt = ⎨⎜ ⎟ × 1.2⎬ × 1× 20 = 0.2kW
⎩⎝ 3600 ⎠ ⎭
IES-24. An air-conditioned room has length, width and height of 20 m, 30 m and 4 m
respectively. The infiltration is assumed to be one air change. The outdoor
vi
and indoor dry bulb temperatures are 40oC and 25oC respectively. The
sensible heat load due to infiltration is [IES-2001; 2003]
(a) 734 kW (b) 12.24 kW (c) 0.204 kW (d) 10 kW
20 × 30 × 4 3
Ci
IES-24Ans (b) Infiltration ‘1’ air change per hour, i.e., (cmm) = m / min
60
[(cmm) = volumetric flow rate cubic meter per minute]
⎛ 20 × 30 × 4 ⎞
1.2 × (cmm) × C p × ( Δt )
1.2 × ⎜ ⎟ ×1.02 × ( 40 − 25 )
⎝ 60 ⎠
w.
Qs = = kW = 12.24kW
60 60
IES-25. An air-conditioned room of volume 10 m3 has infiltration of air equivalent to

3 air changes. Density of air is 1.2 kg/m3, specific heat Cp is 1 kJ/kg-K and
ww
temperature difference between room and ambient air is 20 K. The sensible

heat load due to infiltrated air is [IES-2000]
(a) 60 kJ/hr (b) 12 kJ/hr (c) 6 kW (d) 0.2 kW
IES-25Ans. (d)
IES-26. Moist air enters the cooling coil with mass flow rate of 10 kgda/s at dry bulb
temperature of 30oC and humidity ratio of 0.017 kgw/kgda. It leaves the
cooling coil at dry bulb temperature of16oC and humidity ratio of 0.008
kgw/kgda. If specific heat of humid air is 1.02 kJ/kgda-K and latent heat of
water vapour is 2500 kJ/kgw. The sensible and latent heat transfer of
cooling coil are, respectively [IES-2003]
(a) 140 kW and 25000 kW (b) 142.8 kW and 2.25 kW
Page 120 of 128
Miscellaneous
(c) 142.8 kW and 225 kW (d) 225 kW and 142.8 kW
IES-26Ans. (c) We know that humid specific heat, Cp = Cpa+ωCpv = 1.02 KJ/kgda.K
Therefore, Sensible heat load (SHL) = ma C p ( ΔTdb ) = 10 ×1.02 × (30 − 16) = 142.8kW
( )
and Latent heat load (LHL) = ma (ωi − ωo ) h fg = 10 × ( 0.017 − 0.008 ) × 2500 = 225 kW
IES-27. In an air-conditioning plant the refrigeration load on the coil is 100 TR The
mass and enthalpy of air leaving the coil are 420 kg/minute and 40 kJ/kg
respectively. What will be the enthalpy of the air at the Inlet to the coil
m
under these conditions? [IES-2004]
(a) 80 kJ/kg (b) 90 kJ/kg (c) 100 kJ/kg (d) 102.5 kJ/kg
.co
IES-27Ans. (b) ∴ Q = m1 ( h1 − h2 )
Q 100 × 210kJ / min
or h1 = h2 + = 40 + = 90 kJ / kg
m1 420 kg / min
tas
lda
IES-28. For an office building the outdoor design conditions are 45°C dbt and
humidity ratio of 0.015. The indoor design conditions are 25°C dbt and 0.01
humidity ratio. The supply air state is 15°C dbt and 0.007 humidity ratio. If
the supply air flow rate is 1000 m3/ min and fresh air flow rate is m3/ min,
room sensible and room latent heat loads are, respectively, [IES-2002]
vi
(a) 408 kW and 400 kW (b) 408 kW and 150 kW

(c) 204 kW and 400 kW (d) 204 kW and 150 kW
IES-28Ans. (d)
Ci

1.The recommended outside air required per person for an auditorium is
approximately 0.25 m3/min.
2.Outside air for ventilation purposes causes sensible heat load and also
w.
latent heat load.

3.The sensible heat factor for an auditorium is generally kept as 0.7
IES-29Ans. (d) In order to find the required cooling capacity of the system, one has to take into
ww
account the sensible and latent loads due to ventilation, leakage losses in the return
air ducts and heat added due to return air fan. Typical outdoor (OD) air requirement
for the purpose of ventilation:
Function Occupancy per 100m floor OD air

requirement per
area person (L /s)
Smoking Non -
sm
oki
ng
Offices 7 10 2.5
Page 121 of 128
Miscellaneous
Operation theatres 20 - 15
Lobbies 30 7.5 2.5
Class rooms 50 - 8.0
Meeting places 60 17.5 3.5
IES-30. In air-conditioning design for summer months, the condition inside a

factory where heavy work in performed as compared to a factory in which
light work is performed should have [IES-1998]
(a) lower dry bulb temperature and lower relative humidity
m
(b) lower dry bulb temperature and higher relative humidity
(c) lower dry bulb temperature and same relative humidity
(d) same dry bulb temperature and same relative humidity
.co
IES-30Ans. (a)
IES-31. Two summer air-conditioning systems with non-zero by pass factor are
proposed for a room with a known sensible and latent heat load. System A
operates with ventilation but system B operates without ventilation. Then
the [IES-1995]
tas
a) bypass factor of system A must be less than the bypass factor of system B
(b) bypass factor of system A must be more than the bypass factor of system B
(c) apparatus dew point for system A must be lower than the apparatus dew point for
system B
(d) apparatus dew point for system A must be higher than the apparatus dew point
lda
for system B.
IES-31Ans. (b)
IES-32. Consider the following factors: [IES-1994]

1. Wind velocity
vi
2. Type of activity
3. Indoor design conditions
4. Door openings
Occupancy load in cooling load calculations depends upon
Ci
(a) 1 and 2 (b) 1 and 3 (c) 1 and 4 (d) 2 and 3.

IES-32Ans. (d) Occupancy load in cooling load calculation depend upon type of activity and
indoor design conditions.
w.
Solar refrigeration
IES-33. What is Sol-air temperature? [IES-2006]
(a) It is equal to the sum of outdoor air temperature, and absorbed total radiation
divided by outer surface convective heat transfer coefficient
ww
(b) It is equal to the absorbed total radiation divided by convective heat transfer
coefficient at outer surface
(c) It is equal to the total incident radiation divided by convective heat transfer
coefficient at outer surface
(d) It is equal to the sum of indoor air temperature and absorbed total radiation
divided by convective heat transfer coefficient at outer surface
αI
IES-33Ans. (a) sol-air temperature te = to +
ho
Rate of heat transfer from outside to wall is qo ∴qo = ho (to − t s ) + α I = ho (te − ts )
For heat transfer through building structure the sol-air temperature is used instead
of conduction and solar radiation separately.
Page 122 of 128
Miscellaneous
IES-34. On which of the following factors does sol-air temperature depend?

1. Outdoor air temperature [IES-2003]
2. Intensity of solar radiation
3. Absorptivity of wall
4. Convective heat transfer coefficient at outer surface of wall
5. Indoor design temperature
Choose the correct answer from the codes given below:
(a) 1, 2 and 5 (b) 1, 2 and 3 (c) 3 and 4 (d) 1, 2, 3 and 4
m
IES-34Ans. (d)
IES-35. A thin flat plate 2 m x 2 m is hanging freely in air. The temperature of the
.co
surroundings is 25°C. Solar radiation is falling on one side of the plate at
the rate of 500 W/m2. What should be the convective heat transfer coefficient
in W/m2oC if the temperature of the plate is to remain constant at 30oC?
(a) 25 (b) 50 (c) 100 (d) 200 [IES-2005]
IES-35Ans. (b) Heat absorbed = heat dissipated or G.A = h × ( 2A ) × Δt
IES-36.
or 500 = h × 2 × (30 − 25) or h =
500
2×5
tas
= 50 W / m2 .k
Assertion (A): In an air-conditioned room, the reflective coating should be on the

inside of the window.
lda
Reason (R): plane Window glass is transparent to solar radiation. [IES-1996]
vi
IES-36Ans. (d) A is false but R is true
Duct Design
Ci

Equal friction method of designing ducts is preferred
(a) when system is balanced
w.
(b) when system is not balanced

(c) only for return ducts
(d) for any system
IES-37Ans. (a)
• In the equal friction method, the frictional pressure drop per unit length of the
ww
duct is maintained constant throughout the duct system.

• The method is generally recommended because of its simplicity.
• If an equal friction design has a mixture of short and long runs of duct, the
shortest duct will need a considerable amount of dampering. This is a drawback of
the equal friction design.
• Equal friction method of designing ducts is preferred when system is balanced.
IES-38. Which of the following method (s) is/are adopted in the design of air duct
system? [IES-1998]
1. Velocity reduction method
2. Equal friction method
Page 123 of 128
Miscellaneous
3. Static regain method.
Codes:
(a) 1 alone (b) 1 and 2 (c) 2 and 3 (d) 1, 2 and 3
IES-38Ans. (c)
IES-39. The most commonly used method for the design of duct size is the
(a) velocity reduction method (b) equal friction method. [IES-1996]
(c) static region method (d) dual or double duct method.
m
IES-39Ans. (b) Equal friction method is simple and is most widely used conventional method.
This method usually yields a better design than the velocity method as most of the
available pressure drop is dissipated as friction in the duct runs, rather than in the
.co
balancing dampers. This method is generally suitable when the ducts are not too
long, and it can be used for both supply and return ducts.
IES-40. Consider the following statements pertaining to duct design: [IES-2006]
any means. tas

1. Aspect ratio of ducts should be high.
2. In the equal friction, method of design, use of dampers cannot be eliminated by
3. The static regain method is not suitable for long ducts.

4. The velocity reduction method is employed only in simple systems.
lda
IES-40Ans. (b)
IES-41. Which one of the following statements is true for air conditioning duct
design? [IES-2001]
vi
(a) Static regain method is used, when the duct work is extensive, total pressure drop
is low and flow is balanced
(b) Static regain method is used, when the duct work is extensive, total pressure drop
Ci
is high and flow is unbalanced

(c) Equal friction method is used, when the duct work is extensive, total pressure
drop is low and flow is balanced
(d) Equal friction method is used, when duct work is extensive, total pressure drop is
w.
low and flow is unbalanced

IES-41Ans. (c)
IES-42. If coefficient of contraction at the vena contracta is equal to 062, then what
will be the dynamic loss coefficient in sudden contraction in air-
ww
conditioning duct? [IES-2004]

(a) 0.25 (b) 0.375 (c) 0.55 (d) 0.65
2 2
⎛ 1 ⎞ ⎛ 1 ⎞
IES-42Ans. (b) K=⎜ − 1⎟ = ⎜ − 1⎟ = 0.375
⎝ Cc ⎠ ⎝ 0.62 ⎠
IES-43. Consider the following statements in respect of the contraction and

expansion in air conditioning ducts: [IES-2003]
1. Pressure drop is more in contraction than in expansion.
2. Pressure drop is more in expansion than in contraction.
3. Static pressure increases (regain) in expansion.
4. Static pressure increases (regain) in contraction.
Page 124 of 128
Miscellaneous
(a) 1 and 2 (b) 1, 2 and 3 (c) 1 and 3 (d) 2 and 4
IES-43Ans. (d)

The typical air velocities in the ducts of air-conditioning systems are
1. lower in residential buildings as compared to those of public
buildings
2. higher in residential buildings as compared to those of public
m
buildings
3. higher in industrial buildings as compared to those of public
buildings
.co
4. equal in all types of buildings
(a) 1 alone (b) 1 and 3 (c) 2 and 3 (d) 4 alone
IES-44Ans. (b)
IES-45. The equivalent diameter (D) of a circular duct corresponding to a
(a) D =
IES-45Ans. (d)
a+b
ab
(b) D =
tas
rectangular duct having longer side 'a' and shorter side ‘b', for the same
velocity and pressure drop is given by
ab
a+b
(c) D =
a+b
2ab
[IES-1994]
(d) D =
2ab
a+b
lda
IES-46. Air enters a rectangular duct measuring 30 x 40 cm with a velocity of 8.5 m/s
and a temperature of 40°C. Kinematic viscosity of the air is 16.95 x 10-6 m2/s.
What will be the Reynolds number? [IES-2009]
(a) 1.72 x 105 (b) 2.58 x 105 (c) 0.86 x 105 (d) 0.72 x 105
vi
IES-46Ans. (a)
2ab
LC =
a+b
2 × 0.3 × 0.4
Ci
= = 0.342
( 0.3 + 0.4 )
VLC 8.5 × 0.342
Re = =
ν 16.95 × 10−6
w.
= 171934.26 = 1.72 × 105
IES-47. Instantaneous cooling loads are NOT equal to instantaneous heat gains
because [IES-2003]
ww
(a) Heat gains are offset by cooling provided by the AC system

(b) Indoor temperatures are lower
(c) Comfort conditions are maintained in the space
(d) Of the storage effect in the construction material of walls and roof
IES-47Ans. (d)
Previous 20-Years IAS Answer

Comfort
IAS-1. Assertion (A): The actual inside design temperatures selected in comfort air-
conditioning are not necessarily those conditions of optimum comfort. [IAS-2001]
Page 125 of 128
Miscellaneous
Reason (R): The length and type of occupancy, the outside design conditions and
economic factors affect the choice.
IAS-1Ans. (d) A is false but R is true
The required inside design conditions depend on the intended use of the building. Air
conditioning is required either for providing suitable comfort conditions for the
m
occupants (e.g. comfort air conditioning), or for providing suitable conditions for
storage of perishable products (e.g. in cold storages) or conditions for a process to take
place or for products to be manufactured (e.g. industrial air conditioning). The
.co
required inside conditions for cold storage and industrial air conditioning
applications vary widely depending on the specific requirement. However, the
required inside conditions for comfort air conditioning systems remain
practically same irrespective of the size, type, location, use of the air
conditioning building etc., as this is related to the thermal comfort of the
human beings.
IAS-2.
tas
In room air-conditioning for comfort, the supply air in summer should be at
(a) the same temperature as that of the room
(b) 5 to 10° C below the room temperature
(c) 2 to 30C above the room temperature
[IAS-1997]
lda
(d) at 0° C
IAS-2Ans. (b)
IAS-3. The difference between the comfort airconditioning and industrial

airconditioning lies in the [IAS-1998]
(a) equipment used (b) process adopted
vi
(c) indoor requirements (d) ambient conditions

IAS-3.Ans. (c)
Ci
IAS-4. Which one of the following statements is true for effective temperature, ET?
(a) ET increases with increase in level of activity and it decreases with increase in air
velocity
w.
(b) ET decreases with increase in level of activity and it increases with increase in air
velocity.
(c) ET increases with increase in level of activity and it increases with increase in air
velocity
ww
(d) ET decreases with increase in level of activity and decreases with increase in air
velocity. [IAS-2004]
IAS-4.Ans. (c) Rule: Any activity which reduces comfort will increase ET.

Effective temperature is NOT a true comfort index because
L discomfort may be experienced at extremely high or low humilities.
2, the radiation effect of surrounding surfaces has not been taken into
account.
3. it presumes the absence of drafts.
(a) 1, 2 and 3 are correct (b) 1 and 2 are correct
Page 126 of 128
Miscellaneous
IAS-5.Ans. (b)

1. Is a measure of the sensation of warmth or coldness.
2. Is the uniform temperature of an imaginary enclosure with which man
will exchange the same dry heat by radiation and connection as in the
actual environment.
m
3. Combines the effects of dry bulb temperature, wet bulb temperature and
air movement.
.co
(c) 2 and 3 are correct (d)1 and 3 are correct
IAS-6Ans. (a)
IAS-7. A room air is at a DBT of Tr and relative humidity φr . The effective

temperature of the room is [IAS 1994]
tas
(a) the temperature at which the room air is saturated but gives the same feeling of
comfort as the actual state of the room air
(b) the temperature at which the room air is at 50% relative humidity but gives the
same feeling of comfort as the actual state of the room air
(c) the temperature at which the room air is completely dry but gives the same feeling
lda
of comfort as the actual state of the room air.
(d) none of the above
IAS-7Ans. (a)
Duct Design
vi
IAS-8. Which of the following items related to infiltration of outdoor air in an air-
conditioning system, are correctly matched? [IAS-2007]
1. Stack effect : Height of building
Ci
2. Crack length method : Wind velocity

3. Air change method : Floor area
4. Door opening : Occupancy in kitchen
w.

IAS-8Ans. (a)
below the lists:
ww
List I (Material) List II (Purpose/application)

A. Glass wool 1. Cold storage
B. Ammonia 2. Domestic refrigerators
C G.I. Sheet 3. Insulation
D. Polyurethane 4. Ducting [IAS-1995]
(a) 3 1 4 2 (b) 3 3 4 1
(c) 1 3 4 2 (d) 3 1 2 4
IAS-9Ans. (a)
IAS-10. Which one of the following statements is correct? [IAS-1995]

(a) The sensible heat gain is due to the difference in humidity
Page 127 of 128
Miscellaneous
(b) The latent heat gain is due to the temperature difference between the fresh air
through unconditioned space in the building adds to the sensible heat gain
(c) The heat gain through the walls of ducts carrying conditioned air through
unconditioned space in the building adds to the sensible heat gain
(d) Maximum heat gain to a building occurs through walls
IAS-11Ans. (c)
IAS-12. For air-conditioning the operation theatre in a hospital, the percentage of

outside air in the air supplied is [IAS-1995]
m
(a) zero (b) 20 (c) 50 (d) 100
IAS-12Ans. (d)It is advisable to recalculate infected air of operation theatre and accordingly %
age of outside air is 100%.
.co
tas
vi lda
Ci
w.
ww
Page 128 of 128

RAC SK Mondal 12 PDF

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

RAC SK Mondal 12 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

RAC SK Mondal 12 PDF

Uploaded by

Copyright:

Available Formats

Visit : www.Civildatas.

Refrigeration and Air-

Chapter - 4 : Refrigerant Compressors

Chapter - 6 : Expansion Devices

Chapter - 8 : Vapour Absorption System

Copyright © 2007 S K Mondal

he COP of refrigeratoor is one leess than C

at pump, iff same

Heat Pump & Refrige

(a) 1 ton (b) 5 ton

Heat Pump & Refrigeration Cycles and Systems

(a) 2 kW (b) 3 kW (c) 4 kW (d) 5 kW

IES-5. Assertion (A): If a domestic refrigerator works inside an adiabatic room

with its door open, the room temperature gradually decreases.

IES-6. A refrigerator working on a reversed Carnot cycle has a C.O.P. of 4. If it

Heat Pump & Refrigeration Cycles and Systems

IES-6. Ans. (c) (COP)Heat pump = (COP)refrigerator + 1 = 4 + 1 = 5

IES-7. Assertion (A): An air-conditioner operating as a heat pump is superior to an

IES-8. The coefficient of performance (COP) of a refrigerator working as a heat

reversed in operation to work as a heat pump with operating conditions

IES-11. Operating temperature of a cold storage is –2°C From the surrounding at

Heat Pump & Refrigeration Cycles and Systems

IES-13. A heat pump is shown schematically as [IES-1994]

IES-14. A heat pump working on a reversed Carnot cycle has a C.O.P. of 5. lf it

works as a refrigerator taking 1 kW of work input, the refrigerating effect

Heat Pump & Refrigeration Cycles and Systems

IES-17. Ans. (a) W =

IES-19. In an ideal refrigeration (reversed Carnot) cycle, the condenser and

IES-19. Ans. (a) COP = = = 6.5

IES-20. A refrigerating machine working on reversed Carnot cycle takes out 2 kW of

IES-21. A Carnot refrigerattor require es 1.5 kW//ton of reffrigerationn to mainttain a

Heat Pump & Refrigeration Cycles and Systems

which does not damage the tissue cells of food materials.

Both A and R are individually true and R is the correct explanation of A

Refrigeration capacity (Ton of refrigeration)

IES-26. Ans. (a)

4.18 kJ/kg K) [IES-2001; 2003]

IES-28. A refrigerating machine having coefficient of performance equal to 2 is used

Heat Pump & Refrigeration Cycles and Systems

IES-32. Consider the following statements: [IES-1997]

Temperature at cold and hot junctions

(b) Operating the machine at lower speeds

refrigerating machines it is the reverse, i.e. (T1 – T2) should be lower.

IES-34. Ans. (c) Q = mCP Δt or 0.5 × 12660 = m × 4.2 × ( 30 − 15 ) or m = 100 kg/hr

Previous 20-Years IAS Questions

Heat Engine, Heat Pump

Heat Pump & Refrigeration Cycles and Systems

IAS-2. In the system given above, the

(c) A is true but R is false

Heat Pump & Refrigeration Cycles and Systems

Reversed Carnot Cycle

IAS-9. A refrigeration system operates on the reversed Carnot cycle. The

temperature = 20°C. [IAS-2007]

IAS-10. A refrigerating machine working on reversed Carnot cycle takes out 2 kW of

Heat Pump & Refrigeration Cycles and Systems

IAS-11. A refrigerating machine working on reversed Carnot cycle consumes 6kW to

IAS-11. Ans. (b) COP =