Eaton www.eaton.

eu

Surge Protection
 Surge Protection
1.1
SG05013

1 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.2 Surge Protective Class T1/T2, SPRT12-350

Poles Max. Continous Operating Voltage Type Article No. Units per
UC Designation package

Combined Surge Protective Device SPRT12-350

• incl. FM contact (change-over contact)
• for TN-C

3pole 350 VAC SPRT12-350/3-AX 195235 1

sg04518_r

• incl. FM contact (change-over contact)

• for TN-S/TT
sg04418_r
3pole+NPE 350 VAC SPRT12-350/3+NPE-AX 195236 1

Range of protection Max. Continous Operating Voltage Type Article No. Units per
UC Designation package

Insert for SPRT12-350

L-N / L-PEN 350 VAC SPRT12-350 195237 1
sg04318_r

N-PE 350 VAC SPRT12-350/NPE 195238 1

2 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T1/T2, SPRT12-350 1.3
Description Surge Protective Class T1/T2
• Ready-to-connect Combined Surge Protection Device Type 1/2 on the basis of spark gaps
• Consisting of the base unit and plug-type modules

Technical Data
SPRT12-350/3-AX SPRT12-350/3+NPE-AX
General data
Standards/regulations IEC 61643-11, EN 61643-11 IEC 61643-11, EN 61643-11
IEC test classification T1 / T2 T1 / T2
EN type T1 / T2 T1 / T2
Number of ports One One
SPD design Voltage-switching type Voltage-switching type
Mode of protection L-PEN L-N, L-PE, N-PE
Mounting type DIN rail 35 mm DIN rail 35 mm
Surge protection fault message Optical, remote indicator contact Optical, remote indicator contact
Color Light grey RAL 7035 Light grey RAL 7035
Insulating material PBT-FR PBT-FR
Housing material PBT-FR PBT-FR
Air clearances and creepage distances
(according to EN 60664-1 and EN 61643-11)
Degree of pollution 2 2
Overvoltage category III III
Material group I I
CTI value of material  600  600
Umax < 2 kV < 2 kV
Flammability rating according to UL 94 V-0 V-0
Degree of protection IP20 (only when all terminal points are used) IP20 (only when all terminal points are used)
Shock (operation) 30 g (Half-sine / 11 ms / 3x ±X, ±Y, ±Z) 30 g (Half-sine / 11 ms / 3x ±X, ±Y, ±Z)
Vibration (operation) 5 g (5 - 500 Hz/2.5 h/X, Y, Z) 5 g (5 - 500 Hz/2.5 h/X, Y, Z)
Ambient temperature (operation) -40 °C ... 80 °C -40 °C ... 80 °C
Ambient temperature (storage/transport) -40 °C ... 80 °C -40 °C ... 80 °C
Permissible humidity (operation) 5 % ... 95 % 5 % ... 95 %
Altitude  2000 m (amsl (above mean sea level))  2000 m (amsl (above mean sea level))
Width 106.8 mm 142.4 mm
Height 97 mm 95 mm
Depth 71.2 mm (incl. DIN rail 7.5 mm) 71.2 mm (incl. DIN rail 7.5 mm)
Horizontal pitch 6 Module units 8 Module units
Electrical data
Nominal voltage UN
240/415 V AC (TN-C) 240/415 V AC (TN-S)
240/415 V AC (TT)
Nominal frequency fN 50 Hz (60 Hz) 50 Hz (60 Hz)
Maximum continuous operating voltage UC 350 V AC 350 V AC
Reference test voltage UREF 264 V AC 264 V AC
Rated load current IL 125 A (< 55 °C) 125 A (< 55 °C)
Nominal discharge current (8/20) μs In
(L-PEN) 25 kA -
(L-N) - 25 kA
(L-PE) - 25 kA
(N-PE) - 100 kA
Maximum discharge current (8/20) μs Imax
(L-PEN) 50 kA -
(L-N) - 50 kA
(L-PE) - 50 kA
Impulse discharge current (10/350) μs
Peak value Iimp 25 kA (L-PEN) 25 kA (L-N)
Charge 12.5 As (L-PEN) 12.5 As (L-N)
Specific energy 160 kJ/ (L-PEN) 160 kJ/ (L-N)
Impulse discharge current (10/350) μs (L-PE)
Peak value Iimp - 25 kA
Charge - 12.5 As
Specific energy - 160 kJ/

3 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.4 Surge Protective Class T1/T2, SPRT12-350

SPRT12-350/3-AX SPRT12-350/3+NPE-AX
Impulse discharge current (10/350) μs (N-PE)
Peak value Iimp - 100 kA
Charge - 50 As
Specific energy - 2500 kJ/
Total discharge current (10/350) μs Itotal 75 kA 100 kA
Follow current interrupt rating Ifi
(L-PEN) 50 kA -
(L-N) - 50 kA
(N-PE) - 100 A
Short-circuit current rating ISCCR 50 kA 50 kA
Voltage protection level Up
(L-PEN)  1.5 kV -
(L-N) -  1.5 kV
(L-PE) -  2.5 kV
(N-PE) -  1.5 kV
Residual voltage Ures
(L-PEN)  1.5 kV (at In) -
(L-N) -  1.5 kV (at In)
(L-PE) -  2.5 kV (at In)
(N-PE) -  1.5 kV (at In)
Front of wave sparkover voltage at 6 kV (1.2/50) μs
(L-PEN)  1.5 kV -
(L-N) -  1.5 kV
(L-PE) -  2.5 kV
(N-PE) -  1.5 kV
TOV behavior at UT
(L-PEN) 415 V AC (5 s / withstand mode) -
457 V AC (120 min / withstand mode) -
(L-N) - 415 V AC (5 s / withstand mode)
457 V AC (120 min / withstand mode)
(N-PE) - 1200 V AC (200 ms / withstand mode)
Response time tA  100 ns  100 ns
Current tripping factor k 1.6 1.6
Max. backup fuse with branch wiring 315 A (gG) 315 A (gG)
Max. backup fuse with V-type through wiring (at 35 mm2) 125 A (gG) 125 A (gG)
Additional technical data
Follow current interrupt rating Ifi 100 kA (264 V AC) 100 kA (264 V AC) (L-N)
Short-circuit current rating ISCCR 100 kA (264 V AC) 100 kA (264 V AC)
Remote signaling
Connection name Remote fault indicator contact Remote fault indicator contact
Switching function PDT contact PDT contact
Connection method Plug-in/screw connection via COMBICON Plug-in/screw connection via COMBICON
Operating voltage 12 V AC ... 250 V AC 12 V AC ... 250 V AC
125 V DC (200 mA DC) 125 V DC (200 mA DC)
Operating current 10 mA AC ... 1 A AC 10 mA AC ... 1 A AC
1 A DC (30 V DC) 1 A DC (30 V DC)
Screw thread M2 M2
Conductor cross section
flexible 0.14 mm2 ... 1.5 mm2 0.14 mm2 ... 1.5 mm2
solid 0.14 mm2 ... 1.5 mm2 0.14 mm2 ... 1.5 mm2
AWG 28 ... 16 28 ... 16
Stripping length 7 mm 7 mm
Tightening torque 0.25 Nm 0.25 Nm
Connection data
Connection method Screw terminal blocks Screw terminal blocks
Screw thread M5 M5
Connection technology Biconnect terminal block Biconnect terminal block
Conductor cross section
flexible, solid 2.5 mm2 ... 35 mm2 2.5 mm2 ... 35 mm2
AWG 13 ... 2 13 ... 2
Stripping length 18 mm 18 mm
Connection method Fork-type cable lug Fork-type cable lug
Diameter 5 mm 5 mm
Conductor cross section flexible 1.5 mm2 ... 16 mm2 1.5 mm2 ... 16 mm2
Tightening torque 4.5 Nm 4.5 Nm

4 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T1/T2, SPRT12-350 1.5
Circuit diagrams
SPRT12-350/3-AX SPRT12-350/3+NPE-AX SPRT12-350, SPRT12-350/NPE
12 14 12 14
PEN N
11 FM FM
11

L1 L2 L3
PE L1 L2 L3

Dimensions (mm)
SPRT12-350/3-AX
71,2
106,8 51,5

97
90
45
22,5

63,7

SPRT12-350/3+NPE-AX
71,2
142,4 51,5
95
90
45
22,5

63,7

SPRT12-350, SPRT12-350/NPE
56,1
35,5 49
44,8

5 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.6 Surge Protective Class T1/T2 for busbar mounting (40 mm), SPST12(H)-255

Poles Max. Continous Operating Voltage Type Article No. Units per
UC Designation package

Combined Surge Protective Device SPST12(H)-255

•for TT /TN-C-S

3pole+NPE 255 VAC SPST12-255/3+NPE 195603 1

sg06418_r

SPST12H-255/3+NPE 195605 1

•for TN-C

3pole 255 VAC SPST12-255/3 195602 1

sg06318_r

SPST12H-255/3 195604 1

6 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T1/T2 for busbar mounting (40 mm), SPST12(H)-255 1.7
Description Surge Protective Class T1/T2 for busbar mounting (40 mm), SPST12(H)-255
• Ready-to-connect Combined Surge Protection Device Type 1/2 on the basis of spark gaps
• For mounting on 40 mm busbars
• Scope of application:
To protect consumer systems against transient overvoltages caused by direct and indirect lightning strikes, as well as switching operations
• Lightning protection class III and IV according to IEC 62305
• Meets all requirements for the installation of surge protection according to DIN VDE 0100-534
• For electrical system TN-C

Technical Data
SPST12-255/3 SPST12H-255/3
General data
Standards/regulations IEC 61643-11 2011, EN 61643-11 2012 IEC 61643-11 2011, EN 61643-11 2012
IEC test classification T1 / T2 T1 / T2
EN type T1 / T2 T1 / T2
Number of ports One One
SPD design Voltage-switching type Voltage-switching type
Mode of protection L-PEN L-PEN
Mounting type Busbar 40 mm Busbar 40 mm
Surge protection fault message Optical Optical
Color Light grey RAL 7035 Light grey RAL 7035
Insulating material PC PC
Housing material PA 6.6-FR, PC PA 6.6-FR, PC
Air clearances and creepage distances
(according to EN 60664-1 and EN 61643-11)
Degree of pollution 2 2
Overvoltage category IV IV
Material group IIIa IIIa
CTI value of material  175  175
Umax 1.5 kV 1.5 kV
Flammability rating according to UL 94 V-0 V-0
Degree of protection IP30 (installed) IP30 (installed)
Ambient temperature (operation) -40 °C ... 80 °C -40 °C ... 80 °C
Ambient temperature (storage/transport) -40 °C ... 80 °C -40 °C ... 80 °C
Permissible humidity (operation) 5 % ... 95 % 5 % ... 95 %
Altitude  6000 m (amsl (above mean sea level))  6000 m (amsl (above mean sea level))
Width 47 mm 47 mm
Height 223.2 mm 223.2 mm
Depth 110.7 mm 110.7 mm
Horizontal pitch 2.6 Module units 2.6 Module units
Electrical data
Nominal voltage UN 230/400 V AC (TN-C) 230/400 V AC (TN-C)
Nominal frequency fN 50 Hz (60 Hz) 50 Hz (60 Hz)
Maximum continuous operating voltage UC 255 V AC 255 V AC
Reference test voltage UREF 255 V AC 255 V AC
Nominal discharge current (8/20) μs In 20 kA 20 kA
Impulse discharge current (10/350) μs
Peak value Iimp 7.5 kA 12.5 kA
Charge 3.75 As 6.25 As
Specific energy 15 kJ/ 39 kJ/
Follow current interrupt rating Ifi 25 kA 25 kA
Short-circuit current rating ISCCR 25 kA 25 kA
Voltage protection level Up  1.5 kV  1.5 kV
Front of wave sparkover voltage at 6 kV (1.2/50) μs -  1.5 kV
TOV behavior at UT 337 V AC (5 s / withstand mode) 337 V AC (5 s / withstand mode)
442 V AC (120 min / safe failure mode) 442 V AC (120 min / safe failure mode)
Response time tA  100 ns  100 ns
Insulation resistance Riso > 5 M (500 V DC) > 5 M (500 V DC)
Current tripping factor k 1.6 1.6
Max. backup fuse with branch wiring 250 A (gG) 250 A (gG)

7 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.8 Surge Protective Class T1/T2 for busbar mounting (40 mm), SPST12(H)-255

SPST12-255/3 SPST12H-255/3
Connection data
Connection method Screw terminal blocks Screw terminal blocks
Screw thread M5 M5
Conductor cross section
flexible, solid 2.5 mm2 ... 35 mm2 2.5 mm2 ... 35 mm2
Stripping length 18 mm 18 mm
Tightening torque 4.5 Nm 4.5 Nm

Circuit diagram

SPD L1
SPD L2 &
SPD L3

PEN L1 L2 L3 6

Dimensions (mm)
47 223,2
87,9
110,7

64
20

8 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T1/T2 for busbar mounting (40 mm), SPST12(H)-255 1.9
Description Surge Protective Class T1/T2 for busbar mounting (40 mm), SPST12(H)-255/3+NPE
• Ready-to-connect Combined Surge Protection Device Type 1/2 on the basis of spark gaps
• For mounting on 40 mm busbars
• Scope of application:
To protect consumer systems against transient overvoltages caused by direct and indirect lightning strikes, as well as switching operations
• Lightning protection class III and IV according to IEC 62305
• Meets all requirements for the installation of surge protection according to DIN VDE 0100-534
• For electrical system TT / TN-C-S

Technical Data
SPST12-255/3+NPE SPST12H-255/3+NPE
General data
Standards/regulations IEC 61643-11 2011, EN 61643-11 2012 IEC 61643-11 2011, EN 61643-11 2012
IEC test classification T1 / T2 T1 / T2
EN type T1 / T2 T1 / T2
Number of ports One One
SPD design Voltage-switching type Voltage-switching type
Mode of protection L-N, L-PE, N-PE L-N, L-PE, N-PE
Mounting type Busbar 40 mm Busbar 40 mm
Surge protection fault message Optical Optical
Color Light grey RAL 7035 Light grey RAL 7035
Insulating material PC PC
Housing material PA 6.6-FR, PC PA 6.6-FR, PC
Air clearances and creepage distances
(according to EN 60664-1 and EN 61643-11)
Degree of pollution 2 2
Overvoltage category IV IV
Material group IIIa IIIa
CTI value of material  175  175
Umax 1.5 kV (L-N), 2 kV (L-PE), 1.5 kV (N-PE) 1.5 kV (L-N), 2 kV (L-PE), 1.5 kV (N-PE)
Flammability rating according to UL 94 V-0 V-0
Degree of protection IP30 (installed) IP30 (installed)
Ambient temperature (operation) -40 °C ... 80 °C -40 °C ... 80 °C
Ambient temperature (storage/transport) -40 °C ... 80 °C -40 °C ... 80 °C
Permissible humidity (operation) 5 % ... 95 % 5 % ... 95 %
Altitude  6000 m (amsl (above mean sea level))  6000 m (amsl (above mean sea level))
Width 47 mm 47 mm
Height 223.2 mm 223.2 mm
Depth 110.7 mm 110.7 mm
Horizontal pitch 2.6 Module units 2.6 Module units
Electrical data
Nominal voltage UN 230/400 V AC (TN-S) 230/400 V AC (TN-S)
230/400 V AC (TT) 230/400 V AC (TT)
Nominal frequency fN 50 Hz (60 Hz) 50 Hz (60 Hz)
Maximum continuous operating voltage UC 255 V AC 255 V AC
Reference test voltage UREF 255 V AC 255 V AC
Residual current IPE  5 μA  5 μA
Nominal discharge current (8/20) μs In
(L-N) 20 kA 20 kA
(L-PE) 20 kA 20 kA
(N-PE) 80 kA 80 kA
Impulse discharge current (10/350) μs (L-N)
Peak value Iimp 7.5 kA 12.5 kA
Charge 3.75 As 6.25 As
Specific energy 15 kJ/ 39 kJ/
Impulse discharge current (10/350) μs (L-PE)
Peak value Iimp 7.5 kA 12.5 kA
Charge 3.75 As 6.25 As
Specific energy 15 kJ/ 39 kJ/
Impulse discharge current (10/350) μs (N-PE)
Peak value Iimp 30 kA 50 kA
Charge 15 As 25 As
Specific energy 225 kJ/ 625 kJ/

9 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.10 Surge Protective Class T1/T2 for busbar mounting (40 mm), SPST12(H)-255

SPST12-255/3+NPE SPST12H-255/3+NPE
Follow current interrupt rating Ifi
(L-N) 25 kA 25 kA
(L-PE) 25 kA 25 kA
(N-PE) 100 A 100 A
Short-circuit current rating ISCCR 25 kA 25 kA
Voltage protection level Up
(L-N)  1.5 kV  1.5 kV
(L-PE)  2 kV  2 kV
(N-PE)  1.5 kV  1.5 kV
Front of wave sparkover voltage at 6 kV (1.2/50) μs
(L-N)  1.5 kV  1.5 kV
(L-PE)  2 kV  2 kV
(N-PE)  1.5 kV  1.5 kV
TOV behavior at UT
(L-N) 337 V AC (5 s / withstand mode) 337 V AC (5 s / withstand mode)
442 V AC (120 min / safe failure mode) 442 V AC (120 min / safe failure mode)
(L-PE) 442 V AC (120 min / withstand mode) 442 V AC (120 min / withstand mode)
1455 V AC (200 ms / withstand mode) 1455 V AC (200 ms / withstand mode)
(N-PE) 1200 V AC (200 ms / withstand mode) 1200 V AC (200 ms / withstand mode)
Response time tA  100 ns  100 ns
Insulation resistance Riso > 5 M (500 V DC) > 5 M (500 V DC)
Current tripping factor k 1.6 1.6
Max. backup fuse with branch wiring 250 A (gG) 250 A (gG)
Connection data
Connection method Screw terminal blocks Screw terminal blocks
Screw thread M5 M5
Conductor cross section
flexible, solid 2.5 mm2 ... 35 mm2 2.5 mm2 ... 35 mm2
Stripping length 18 mm 18 mm
Tightening torque 4.5 Nm 4.5 Nm

Circuit diagram

SPD L1
SPD L2 &
SPD L3

N L1 L2 L3 PE 6

Dimensions (mm)
47 223,2
87,9
110,7

64
20

10 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T1/T2 (formerly B+C), SPBT12 1.11
Description Type Article No. Units per
Designation package

Lightning current arrester - surge arrester sets, Lightning protection classes III, IV
SG29612
Without remote indication
TN-S/TT Set 1+N Set SPBT12-280-1+NPE50 184752 1 / 30
TN-S-Set 2pole SPBT12-280/2 158309 1 / 60
TN-C-Set 3pole SPBT12-280/3 158330 1 / 40
TN-S-Set 4pole SPBT12-280/4 158331 1 / 30
TN-S/TT Set 3+N Set SPBT12-280-3+NPE50 184750 1 / 60
TN-S/TT Set 3+N Set with busbar SPBT12-280-3+NPE50/BB 184751 1
TN-S/TT-Set 1+1pole SPBT12-280-1+NPE 158308 1 / 40
SPBT12-280/3
TN-S/TT-Set 3+1pole SPBT12-280-3+NPE 158332 1 / 20
TN-S/TT-Set 3+1pole SPBT12-280-3+NPE/BB 158333 1

Accessories
Auxiliary switch for SPBT12-280 ASAUXSC-SPM 131785 4 / 120
Busbar ZV-KSBI...

Impulse current Type Article No. Units per

Iimp (10/350) μs Designation package

Lightning current arrester - surge arrester SPBT12

SG27112
Complete
12.5 kA L - (PE) N SPBT12-280/1 158306 12 / 120
50 kA N-PE SPBT12-NPE50 184749 1 / 60
100 kA N-PE SPBT12-NPE100 158307 1 / 60

SPBT12-280/1
sg63312
Insert
12.5 kA Insert SPBT12-280 167341 4 / 120

11 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.12 Surge Protective Class T1/T2 (formerly B+C), SPBT12

Description Surge Protective Class T1&T2

• Field of application:
For the protection of low voltage distribution systems against transient overvoltage caused by direct and indirect lightning stroke and switching operations
• Application according to IEC 60364-5-53 Clause 534
• Test class I , II according to IEC 61643-1
• SPD-type T1 , T2 according to EN 61643-11
• Lightning protection classes III and IV according to IEC 62305
• Busbars ZV-KSBI are available for all customary applications

Technical Data
SPBT12-280... SPBT12-NPE50 SPBT12-NPE100
Electrical per pole
Responding time (rate of voltage rise 5 kV/μs) < 25 ns < 100 ns < 100 ns
Voltage protection level Up < 1.5 kV < 1.4 kV < 1.5 kV
Voltage protection level at 5 kA (8/20) μs Up 950 V – –
Max. continuous operating voltage UC 280 VAC 260 VAC 255 VAC
TOV test value UT 370 VAC (5 s) 1200 VAC (200 ms) 1200 VAC (200 ms)
Rated frequency 50/60 Hz 50/60 Hz 50/60 Hz
Open circuit voltage Uoc 10 kV – 20 kV
Nominal discharge current (8/20) μs In 25 kA 50 kA 100 kA
Max. discharge current Imax 50 kA 100 kA 100 kA
Impulse current (10/350) μs Iimp
Peak current 12.5 kA 50 kA 100 kA
Charge Q 6.25 As 25 As 50 As
Specific energy 39,1 kJ/ 625 kJ/ 2500 kJ/
Follow current interrupt rating Ifi – 100 Ar.m.s. 100 Ar.m.s.
Maximum back-up fuse 160 AgL/gG – –
Maximum short-circuit current 50 Ar.m.s. – –
Connection diagram

Mechanical
Frame size 45 mm 45 mm 45 mm
Device height 80 mm 80 mm 80 mm
Device width 17.5 mm 17.5 mm 35 mm
Weight 121 g 93 g 250 g
Permitted ambient temperature -40°C to +70°C -40°C to +70°C -40°C to +70°C
Degree of protection (built-in) IP40 IP40 IP40
Upper and lower lift terminal capacity 4 - 25 mm2 top 4 - 50 mm2. bottom 4 - 35 mm2 4 - 35 mm2
Upper and lower open mouthed terminals for busbar thickness up to 1.5 mm top - / bottom 1.5 mm 1.5 mm
Tightening torque of terminal screws 2.4 - 3 Nm 2.4 - 3 Nm 2.4 - 3 Nm
Quick fastening on DIN rail according to IEC/EN 60715 IEC/EN 60715 IEC/EN 60715
Accessories: busbars 16 mm2 Type ZV-KSBI ... Type ZV-KSBI ... Type ZV-KSBI ...

Dimensions (mm) Lightning current arrester - surge arrester sets, Lightning protection classes III, IV
SPBT12-280 SPBT12-NPE100
SPBT12-NPE50

SPBT12-
280/2 SPBT12-280/3

. . . SPBT12-280

12 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T1/T2 (formerly B+C), SPBT12 1.13
Technical Data
SPBT12-280-1+NPE50 SPBT12-280-3+NPE50
Electrical per pole
Responding time (rate of voltage rise 5 kV/μs) L-N / N-PE < 25 ns / < 100 ns < 25 ns / < 100 ns
Voltage protection level L-N / L-PE / N-PE Up < 1.5 kV < 1.5 kV
Max. continuous operating voltage L-N / N-PE UC 280 VAC / 260 VAC 280 VAC / 260 VAC
TOV test value UT
5s L-N / L-PE 348 VAC / 370 VAC 348 VAC / 370 VAC
200 ms N-PE 1200 VAC 1200 VAC
Rated frequency 50/60 Hz 50/60 Hz
Open circuit voltage Uoc 10 kV 20 kV
Nominal discharge current (8/20) μs L-N / N-PE In 25 kA / 50 kA 3x25 kA / 50 kA
Max. discharge current L-N / N-PE Imax 50 kA / 100 kA 3x50 kA / 100 kA
Impulse current (10/350) μs Iimp
Peak current L-N / N-PE 12.5 kA / 50 kA 3x12.5 kA / 50 kA
Charge Q 25 As 25 As
Specific energy 625 kJ/ 625 kJ/
Follow current interrupt rating N-PE Ifi 100 Ar.m.s. 100 Ar.m.s.
Maximum back-up fuse – –
Maximum short-circuit current – –
Connection diagram PE L PE L1 L2 L3

N N

Mechanical
Frame size 45 mm 45 mm
Device height 80 mm 80 mm
Device width 35 mm 70 mm
Weight 218 g 470 g
Permitted ambient temperature -40°C to +70°C -40°C to +70°C
Degree of protection (built-in) IP40 IP40
Upper and lower lift terminal capacity
L, N 4 - 25 mm2 4 - 25 mm2
N, PE 4 - 50 mm2 4 - 50 mm2
Upper and lower open mouthed terminals for busbar thickness up to 1.5 mm 1.5 mm
Tightening torque of terminal screws 2.4 - 3 Nm 2.4 - 3 Nm
Quick fastening on DIN rail according to IEC/EN 60715 IEC/EN 60715
Accessories: busbars 16 mm2 Type ZV-KSBI ... Type ZV-KSBI ...

Lightning current arrester - surge arrester sets, Lightning protection classes III, IV
L, N, PE L1, L2, L3, N, PE
TN-S-System TN-S/TT-System TN-S/TT-System
3 x 230/400 VAC 3 x 230/400 VAC 3 x 230/400 VAC
(3 x 220/380 VAC) (3 x 220/380 VAC) (3 x 220/380 VAC)
(3 x 240/415 VAC) (3 x 240/415 VAC) (3 x 240/415 VAC)
PE PE PE L1 L2 L3 N
L L1 L2 L3

. . . SPBT12-280
. . . SPBT12-NPE50
2 1 2 1 1 1 2 1 1 1 3 . . . ASLTT-63
SPBT12-280-1+NPE50 SPBT12-280-3+NPE50 SPBT12-280-3+NPE50/BB

N N N

13 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.14 Surge Protective Class T1/T2 (formerly B+C), SPBT12

Technical Data
SPBT12-280-1+NPE SPBT12-280-3+NPE
Electrical per pole
Responding time (rate of voltage rise 5 kV/μs) L-N / N-PE < 25 ns / < 100 ns < 25 ns / < 100 ns
Voltage protection level L-N / L-PE / N-PE Up < 1.5 kV < 1.5 kV
Max. continuous operating voltage L-N / N-PE UC 280 VAC / 255 VAC 280 VAC / 255 VAC
TOV test value UT
5s L-N / L-PE 348 VAC / 370 VAC 348 VAC / 370 VAC
200 ms N-PE 1200 VAC 1200 VAC
Rated frequency 50/60 Hz 50/60 Hz
Open circuit voltage Uoc 10 kV 20 kV
Nominal discharge current (8/20) μs L-N / N-PE In 25 kA / 100 kA 3x25 kA / 100 kA
Max. discharge current L-N / N-PE Imax 50 kA / 100 kA 3x50 kA / 100 kA
Impulse current (10/350) μs Iimp
Peak current L-N / N-PE 12.5 kA / 100 kA 3x12.5 kA / 100 kA
Charge Q 50 As 50 As
Specific energy 2500 kJ/ 2500 kJ/
Follow current interrupt rating N-PE Ifi 100 Ar.m.s. 100 Ar.m.s.
Maximum back-up fuse 160 AgL/gG 160 AgL/gG
Maximum short-circuit current 50 kAr.m.s. 50 kAr.m.s.
Connection diagram PE L PE L1 L2 L3

N N

Mechanical
Frame size 45 mm 45 mm
Device height 80 mm 80 mm
Device width 52.5 mm 87.5 mm
Weight 375 g 626 g
Permitted ambient temperature -40°C to +70°C -40°C to +70°C
Degree of protection (built-in) IP40 IP40
Upper and lower lift terminal capacity
L, N 4 - 25 mm2 4 - 25 mm2
N, PE 4 - 35 mm2 4 - 35 mm2
Upper and lower open mouthed terminals for busbar thickness up to 1.5 mm 1.5 mm
Tightening torque of terminal screws 2.4 - 3 Nm 2.4 - 3 Nm
Quick fastening on DIN rail according to IEC/EN 60715 IEC/EN 60715
Accessories: busbars 16 mm2 Type ZV-KSBI ... Type ZV-KSBI ...

Lightning current arrester - surge arrester sets, Lightning protection classes III, IV
L, N, PE L1, L2, L3, N, PE
TN-S-System TN-S/TT-System TN-S/TT-System
3 x 230/400 VAC 3 x 230/400 VAC 3 x 230/400 VAC
(3 x 220/380 VAC) (3 x 220/380 VAC) (3 x 220/380 VAC)
(3 x 240/415 VAC) (3 x 240/415 VAC) (3 x 240/415 VAC)
PE PE PE L1 L2 L3 N
L L1 L2 L3

. . . SPBT12-280
. . . ASAUXSC-SPM
3 1 3 1 1 1 3 1 1 1 4 . . . SPBT12-NPE100
SPBT12-280-1+NPE SPBT12-280-3+NPE SPBT12-280-3+NPE/BB
. . . ASLTT-63

N N N

14 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T2 (formerly C), SPCT2 1.15
Poles Max. Continous Operating In (8/20) μs Type Article No. Units per
Voltage UC Designation package

Plug-in surge arrester SPCT2. 1- to 4pole

SG04713
Complete (2- and multi-pole surge arresters are supplied with busbar)
1pole 75 VAC 20 kA SPCT2-075/1 167578 12/120
1pole 135 VAC 20 kA SPCT2-135/1 167583 12/120
1pole 175 VAC 20 kA SPCT2-175/1 167588 12/120
1pole 280 VAC 20 kA SPCT2-280/1 167593 12/120
1pole 335 VAC 20 kA SPCT2-335/1 167598 12/120
1pole 385 VAC 20 kA SPCT2-385/1 167603 12/120
1pole 460 VAC 20 kA SPCT2-460/1 167608 12/120
SPCT2-280/3 1pole 580 VAC 20 kA SPCT2-580/1 167613 12/120
1pole 260 VAC 30 kA SPCT2-NPE60/1 167618 12/120
2pole 75 VAC 2x20 kA SPCT2-075/2 167579 1/60
2pole 135 VAC 2x20 kA SPCT2-135/2 167584 1/60
2pole 175 VAC 2x20 kA SPCT2-175/2 167589 1/60
2pole 280 VAC 2x20 kA SPCT2-280/2 167594 1/60
2pole 335 VAC 2x20 kA SPCT2-335/2 167599 1/60
2pole 385 VAC 2x20 kA SPCT2-385/2 167604 1/60
2pole 460 VAC 2x20 kA SPCT2-460/2 167609 1/60
2pole 580 VAC 2x20 kA SPCT2-580/2 167614 1/60
3pole 75 VAC 3x20 kA SPCT2-075/3 167580 1/40
3pole 135 VAC 3x20 kA SPCT2-135/3 167585 1/40
3pole 175 VAC 3x20 kA SPCT2-175/3 167590 1/40
3pole 280 VAC 3x20 kA SPCT2-280/3 167595 1/40
3pole 335 VAC 3x20 kA SPCT2-335/3 167600 1/40
3pole 385 VAC 3x20 kA SPCT2-385/3 167605 1/40
3pole 460 VAC 3x20 kA SPCT2-460/3 167610 1/40
3pole 580 VAC 3x20 kA SPCT2-580/3 167615 1/40
4pole 75 VAC 4x20 kA SPCT2-075/4 167581 1/30
4pole 135 VAC 4x20 kA SPCT2-135/4 167586 1/30
4pole 175 VAC 4x20 kA SPCT2-175/4 167591 1/30
4pole 280 VAC 4x20 kA SPCT2-280/4 167596 1/30
4pole 335 VAC 4x20 kA SPCT2-335/4 167601 1/30
4pole 385 VAC 4x20 kA SPCT2-385/4 167606 1/30
4pole 460 VAC 4x20 kA SPCT2-460/4 167611 1/30
4pole 580 VAC 4x20 kA SPCT2-580/4 167616 1/30
1+N 280 VAC 20 kA SPCT2-280-1+NPE 167619 1/60
1+N 335 VAC 20 kA SPCT2-335-1+NPE 167621 1/60
1+N 385 VAC 20 kA SPCT2-385-1+NPE 167623 1/60
1+N 460 VAC 20 kA SPCT2-460-1+NPE 167625 1/60
1+N 580 VAC 20 kA SPCT2-580-1+NPE 167627 1/60
3+N 280 VAC 20 kA SPCT2-280-3+NPE 167620 1/30
3+N 335 VAC 20 kA SPCT2-335-3+NPE 167622 1/30
3+N 385 VAC 20 kA SPCT2-385-3+NPE 167624 1/30
3+N 460 VAC 20 kA SPCT2-460-3+NPE 167626 1/30
3+N 580 VAC 20 kA SPCT2-580-3+NPE 167628 1/30
3+N/BB 280 VAC 3x20 kA SPCT2-280-3+NPE/BB 167629 1
3+N/BB 335 VAC 3x20 kA SPCT2-335-3+NPE/BB 167630 1
3+N/BB 385 VAC 3x20 kA SPCT2-385-3+NPE/BB 167631 1
3+N/BB 460 VAC 3x20 kA SPCT2-460-3+NPE/BB 167632 1

Plug-in surge arrester SPCT2. Insert

sg08213
Insert 1pole
Insert 75 VAC 20 kA SPCT2-075 167577 4/120
Insert 135 VAC 20 kA SPCT2-135 167582 4/120
Insert 175 VAC 20 kA SPCT2-175 167587 4/120
Insert 280 VAC 20 kA SPCT2-280 167592 4/120
Insert 335 VAC 20 kA SPCT2-335 167597 4/120
Insert 385 VAC 20 kA SPCT2-385 167602 4/120
Insert 460 VAC 20 kA SPCT2-460 167607 4/120
Insert 580 VAC 20 kA SPCT2-580 167612 4/120
Insert 260 VAC 30 kA SPCT2-NPE60 167617 4/120

15 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.16 Surge Protective Class T2 (formerly C), SPCT2

Description Surge Protective Class T2

• Field of application:
For the protection of low voltage distribution systems against transient overvoltage caused by direct and indirect lightning stroke and switching operations
• Test class II according to IEC 61643-1+A1
• SPD-type T2 , according to EN 61643-11
• Auxiliary switch ASAUXSC-SPM for remote message transmission can be mounted onto the device

Technical Data
Inserts SPCT2-075 SPCT2-135 SPCT2-175 SPCT2-280 SPCT2-335 SPCT2-385 SPCT2-460
Electrical
Mechanical coding x x x x x x x
Responding time (rate of voltage rise 5 kV/μs) < 25 ns < 25 ns < 25 ns < 25 ns < 25 ns < 25 ns < 25 ns
Voltage protection level at nominal discharge current / Uoc Up < 550 V < 800 V < 1.0 kV < 1.4 kV < 1.6 kV < 1.8 kV < 2.2 kV
Voltage protection level at 5 kA (8/20) μs Up 400 V 550 V 700 V 1000 V 1200 V 1350 V 1700 V
Max. continuous operating voltage UC 75 VAC 135 VAC 175 VAC 280 VAC 335 VAC 385 VAC 460 VAC
TOV test value (5 s) UT = UC = UC = UC 350 VAC 415 VAC 415 VAC 580 VAC
Rated frequency 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz 50/60 Hz
Open circuit voltage Uoc – – – 10 kV 5 kV – –
Nominal discharge current (8/20) μs In 15 kA 20 kA 20 kA 20 kA 20 kA 20 kA 20 kA
Charge Q at In 0.43 As 0.57 As 0.57 As 0.57 As 0.57 As 0.57 As 0.57 As
Specific energy at In 3.2 kJ/ 5.7 kJ/ 5.7 kJ/ 5.7 kJ/ 5.7 kJ/ 5.7 kJ/ 5.7 kJ/
Max. discharge current Imax 30 kA 40 kA 40 kA 40 kA 40 kA 40 kA 40 kA
Follow current interrupt rating Ifi – – – – – – –
Maximum back-up fuse
Maximum short-circuit current  125 AgL PLHT-C100
50 kAr.m.s. 20 kAr.m.s.

Connection diagram

Mechanical
Frame size 45 mm
Device height 80 mm
Device width
1pole 17.5 mm (1MU)
1+1pole, 2pole 35 mm (2MU)
3pole 52.5 mm (3TE)
3+1pole, 4pole 70 mm (4TE)
Mechanical coding
1pole x
1+1pole yx
2pole xx
3pole xxx
3+1pole yxxx
4pole xxxx
Weight base 1P, 1+1P, 2P, 3P, 3+1P, 4P 53/120/120/180/240/240 g
Weight complete devices 1P, 1+1P, 2P, 3P, 3+1P, 4P 110/201/220/330/412/440 g
Permitted ambient temperature -40°C to +70°C
Degree of protection (built-in) IP40
Upper and lower lift terminal capacity 4 - 25 mm2
Upper and lower open mouthed terminals for busbar thickness up to 1.5 mm
Tightening torque of terminal screws 2.4 - 3 Nm
Quick fastening on DIN rail according to IEC/EN 60715
Accessories: busbars 16 mm2 Type ZV-KSBI ...

16 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T2 (formerly C), SPCT2 1.17
Technical Data
Inserts SPCT2-580 SPCT2-NPE60
Electrical
Mechanical coding x y
Responding time (rate of voltage rise 5 kV/μs) < 25 ns < 100 ns
Voltage protection level at nominal discharge current / Uoc Up < 2.6 kV < 1.0 kV
Voltage protection level at 5 kA (8/20) μs Up 2000 V –
Max. continuous operating voltage UC 580 VAC 260 VAC
TOV test value UT = UC (5 s) 1200 VAC (200 ms)
Rated frequency 50/60 Hz 50/60 Hz
Open circuit voltage Uoc – –
Nominal discharge current (8/20) μs In 20 kA 30 kA
Charge Q at In 0.57 As 0.57 As
Specific energy at In 5.7 kJ/ 5.7 kJ/
Max. discharge current Imax 40 kA 60 kA
Follow current interrupt rating Ifi – 100 Ar.m.s.
Maximum back-up fuse
Maximum short-circuit current  125 AgL PLHT-C100
50 kAr.m.s. 20 kAr.m.s.

Connection diagram

Mechanical
Frame size 45 mm
Device height 80 mm
Device width
1pole 17.5 mm (1MU)
1+1pole, 2pole 35 mm (2MU)
3pole 52.5 mm (3TE)
3+1pole, 4pole 70 mm (4TE)
Mechanical coding
1pole x
1+1pole yx
2pole xx
3pole xxx
3+1pole yxxx
4pole xxxx
Weight base 1P, 1+1P, 2P, 3P, 3+1P, 4P 53/120/120/180/240/240 g
Weight complete devices 1P, 1+1P, 2P, 3P, 3+1P, 4P 110/201/220/330/412/440 g
Permitted ambient temperature -40°C to +70°C
Degree of protection (built-in) IP40
Upper and lower lift terminal capacity 4 - 25 mm2
Upper and lower open mouthed terminals for busbar thickness up to 1.5 mm
Tightening torque of terminal screws 2.4 - 3 Nm
Quick fastening on DIN rail according to IEC/EN 60715
Accessories: busbars 16 mm2 Type ZV-KSBI ...

Dimensions (mm)

17 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.18 Surge Protective Class T2 (formerly C), SPCT2

Technical Data
SPCT2-1+NPE SPCT2-3+NPE
Electrical
Mechanical coding yx yxxx
Responding time (rate of voltage rise 5 kV/μs) L-N/N-PE/L-PE < 25ns/< 100ns/< 100ns < 25ns/< 100ns/< 100ns
Max. continuous operating voltage L-N/N-PE UC 335VAC/260VAC 280VAC/260VAC
TOV test value UT
5s L-N 415 VAC 350 VAC
200 ms N-PE 1200 VAC 1200 VAC
Rated frequency 50/60 Hz 50/60 Hz
Nominal discharge current (8/20) μs L-N/N-PE/L-PE In 20 kA 20 kA
Voltage protection level at In L-N/N-PE/L-PE Up 1600V/1000V/1650V 1000V/1000V/1300V
Max. discharge current (8/20) μs L-N/N-PE/L-PE Imax 40 kA 40 kA
Follow current interrupt rating N-PE Ifi 100 Ar.m.s. 100 Ar.m.s.
Maximum back-up fuse
Maximum short-circuit current  125 AgL PLHT-C100
50 kAr.m.s. 20 kAr.m.s.

Connection diagram L1 L2 L3

x x

N N

y y

Mechanical
Mechanical coding of base yx yxxx
Frame size 45 mm 45 mm
Device height 80 mm 80 mm
Device width 35 mm 70 mm
Weight 201 g 412 g
Permitted ambient temperature -40°C to +70°C -40°C to +70°C
Degree of protection (built-in) IP40 IP40
Upper and lower lift terminal capacity 1 - 25 mm2 1 - 25 mm2
Upper and lower open mouthed terminals for busbar thickness up to 1.5 mm 1.5 mm
Tightening torque of terminal screws 2.4 - 3 Nm 2.4 - 3 Nm
Quick fastening on DIN rail according to IEC/EN 60715 IEC/EN 60715
Accessories: busbars 16 mm2 Type ZV-KSBI ... Type ZV-KSBI ...

Dimensions (mm) Application Examples

SPCT2-1+NPE SPCT2-3+NPE

18 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T2 (formerly C), SPCT2 1.19
Surge arrester Sets

Surge Protective Class C, SPCT2

Surge Arrester Set SPCT2-335-3+NPE/BB
• The 3+1 circuit offers a universal solution for surge protection in low voltage distribution systems
• Suitable for TT- and TN-S-systems according to IEC 60364-5-53 Clause 534
• Remote message transmission is possibly by mounting auxiliary switch ASAUXSC-SPM
• Busbar connected, minimum installation work required

Content

SPCT2-335-3+NPE/BB
- 1 unit SPCT2-335-3+NPE Surge arrester
- 1 unit ASLTT-63 Lead-through terminal
- busbar included

19 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.20 Surge Protective Class T2 (formerly C), SPCT2

Poles Max. Continous Operating In (8/20) μs Type Article No. Units per
Voltage UC Designation package

Surge arrester SPET2, 1- to 4pole

SG64212
Complete (2- and multi-pole surge arresters are supplied with busbar)
1pole 280 VAC 10 kA SPET2-280/1 168741 2/120
2pole 280 VAC 2x10 kA SPET2-280/2 168742 1/60
3pole 280 VAC 3x10 kA SPET2-280/3 168692 1/40
4pole 280 VAC 4x10 kA SPET2-280/4 168693 1/30
1pole+N 280 VAC 10 kA SPET2-280/1+NPE 168699 1/60
3pole+N 280 VAC 10 kA SPET2-280/3+NPE 168700 1/30
1pole 335 VAC 10 kA SPET2-335/1 168695 2/120
SPET2-280/2
2pole 335 VAC 2x10 kA SPET2-335/2 168696 1/60
3pole 335 VAC 3x10 kA SPET2-335/3 168697 1/40
4pole 335 VAC 4x10 kA SPET2-335/4 168698 1/30
1pole+N 335 VAC 10 kA SPET2-335/1+NPE 168701 1/60
3pole+N 335 VAC 10 kA SPET2-335/3+NPE 168702 1/30

Surge arrester SPET2, Insert

sg63412
Insert 1pole
Insert 280 VAC 10 kA SPET2-280 168740 2/120
Insert 335 VAC 10 kA SPET2-335 168694 2/120

Accessories
Auxiliary switch for SPBT12. SPCT2. SPET2. SPDT3 ASAUXSC-SPM 131785 8/80
SG83311

Description Type Article No. Units per

Designation package

Lead-through terminal for SPB, ASLTT-63

Lead-through terminal ASLTT-63 131784 12/120
SG59511

20 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T2 (formerly C), SPCT2 1.21
Description Surge arrester SPET2
• Field of application:
For the protection of low voltage distribution systems against transient overvoltage caused by direct and indirect lightning stroke and switching operations
• Test class II according to IEC 61643-1+A1
• SPD-type T2 , according to EN 61643-11
• Busbars ZV-KSBI are available for all customary applications
• Suitable for busbar connection to all Xtra Combinations switchgear

Technical Data
SPET2-280 SPET2-335 SPET2-NPE60
Electrical
Responding time (rate of voltage rise 5 kV/μs) < 25 ns < 25 ns < 100 ns
Voltage protection level at nominal discharge current Up < 1.2kV < 1.3kV < 1.0 kV
Voltage protection level at 5 kA (8/20) μs Up 1000 V 1200 V -
Max. continuous operating voltage UC 280 VAC 335 VAC 260 VAC
TOV test value (5 s) UT 335 VAC 400 VAC 1200 VAC
Rated frequency 50/60 Hz 50/60 Hz 50/60 Hz
Nominal discharge current (8/20) μs In 10 kA 10 kA 20 kA
Charge Q at In 0.57 As 0.57 As 0.57 As
Specific energy at In 5.7 kJ/ 5.7 kJ/ 5.7 kJ/
Max. discharge current Imax 20 kA 20 kA 60 kA
Follow current interrupt rating Ifi – – 100 Ar.m.s.
Maximum back-up fuse
 100 AgL  C63
Maximum short-circuit current
50 kAr.m.s. 10 kAr.m.s.

Connection diagram

Mechanical
Frame size 45 mm
Device height 80 mm
Device width 17.5 mm
Weight 87 g
Permitted ambient temperature -40°C to +70°C
Degree of protection (built-in) IP40
Upper and lower lift terminal capacity 4 - 25 mm2
Upper and lower open mouthed terminals for busbar thickness up to 1.5 mm
Tightening torque of terminal screws 2 - 2.5 Nm
Quick fastening on DIN rail according to IEC/EN 60715
Accessories: busbars 16 mm2 Type ZV-KSBI ...

Dimensions (mm)

21 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.22 Surge Protective Class T2 (formerly C), SPCT2

Application Examples SPET2 according to IEC 60364-5-53 Clause 534

1 2 3 4

IEC 60364-5-534 SPET2- SPET2- --- SPET2-

IEC 60364-5-53 Clause 534 280/3 280/4 335/3+NPE
A ÖVE ÖNORM E8001-1 SPET2- SPET2- --- SPET2-
335/3 335/4 335/3+NPE
D VDE V 0100-534 SPET2- SPET2- --- SPET2-
280/3 280/4 335/3+NPE
N SPET2- SPET2- SPET2- ---
1 2 3 280/3 280/4 280/3

5 6 7 8
ZV-KSBI-3TE ZV-KSBI-4TE ZV-KSBI-3TE

IEC 60364-5-534 SPET2- SPET2- --- ---

IEC 60364-5-53 Clause 534 280/2 335/1+NPE
A ÖVE ÖNORM E8001-1 SPET2- SPET2- --- ---
335/2 335/1+NPE
D VDE V 0100-534 SPET2- SPET2- --- ---
280/2 335/1+NPE
F UTE C 20-443 --- --- SPET2- SPET2-
280/1 280/3

4 5

ZV-KSBI-4TE ZV-KSBI-2TE

TN-S-/TT-System TN-S-/TT-System
230 VAC 3 x 230/400 VAC

6 6 7 Z-
D63 8 Z-
D63

ZV-KSBI-2TE ZV-KSBI-3TE ZV-KSBI-2TE ZV-KSBI-4TE

22 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T2 (formerly C), SPCT2 1.23
Description Auxiliary switch for Surge arrester ASAUXSC-SPM
• Field of application:
For mounting onto surge predective devices for external defect message transmission
• Design basically in accordance with IEC 60947-5-1
• Can be mounted subsequentlyr
• Suitable withSPBT12. SPCT2. SPET2. SPDT3. SP-B+C

Technical Data
ASAUXSC-SPM
Electrical
Rated insulation voltage 250 V
Rated frequency 50/60 Hz
Switching contact 1 CO
Minimum voltage per contact 24 VAC
Rated operational current AC12 2 A / 250 VAC
Maximum back-up fuse 2 A gL
Overvoltage category IV
Pollution degree 2
Mechanical
Frame size 45 mm
Device height 80 mm
Device width 8.8 mm
Mounting Screw-mounting
Degree of protection, built-in IP40
Terminal protection finger and hand touch safe according to DGUV VS3, EN 50274
Upper and lower terminals lift terminals
Terminal capacity 2 x 2.5 mm2
Tightening torque of terminal screws 0.8 - 1 Nm

Connection diagram

Dimensions (mm)

Application Examples

SPCT2-280/2 SPBT12-280/3 SPCT2-460/4

23 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.24 Surge Protective Class T2 (formerly C), SPCT2

Description Lead-Through Terminal for Surge Protective Devices, SPD-type 2 (Surge Protective Class C), ASLTT-63
• The lead-through terminal permits orderly wiring of SPDs types 2 (Surge Protective Class C).
It serves as lead-through terminal in circuits requiring vertical connections from the upper to the lower SPD connection level.
• 1pole
• Suitable for standard busbar connection to EATON switchgear

Technical Data
ASLTT-63
Electrical
Rated voltage 690 V AC/DC
Rated current 63 A
Rated frequency 50/60 Hz
Mechanical
Frame size 45 mm
Device height 80 mm
Device width 17.5 mm
Mounting quick fastening on DIN rail IEC/EN 60715
Degree of protection, built-in IP40
Terminal protection finger and hand touch safe according to DGUV VS3, EN 50274
Upper and lower terminals Lift- and Maulklemme
Terminal capacity 1 - 25 mm2
Busbar thickness 0.8 - 2 mm
Tightening torque of terminal screws 2.4 - 3 Nm

Connection diagram

Dimensions (mm)

Application Example / Connection type 2 according to IEC 60364-5-53 Clause 534

SPCT2-335- ASLTT-
3+NPE 63

24 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T3 (formerly D), SPDT3 1.25
Poles Max. Continous Operating Voltage Type Article No. Units per
UC Designation package

Surge arrester SPDT3

SG03213
Complete (2-pole surge arresters are supplied with busbar)
1pole+N 335 VAC SPDT3-335-1+NPE 170487 1/60
2pole 280 VAC SPDT3-280/2 170485 1/60

SPDT3-335-1+NPE

Max. Continous Operating Voltage Type Article No. Units per

UC Designation package

Surge arrester SPDT3, Insert

sg03413
Insert 1pole
280 VAC SPDT3-280 170484 2/120
335 VAC SPDT3-335 170486 2/120

25 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.26 Surge Protective Class T3 (formerly D), SPDT3

Description Surge Protective Class T3

• Field of application:
For fine protection of user equipment against transient overvoltage
• For mounting on DIN rails in distribution boxes for electrical installation
• No decoupling from upstream surge protection in the low voltage distribution system required
• Test class III according to IEC 61643-1+A1
• SPD-type T3 according to EN 61643-11
• Suitable for high back-up fuse 63 A gL / C 63
• Auxiliary switch ASAUXSC-SPM for remote message transmission can be mounted onto the device

Technical Data
SPDT3-335-1+NPE SPDT3-280/2
Electrical
Mechanical coding yx xx
Responding time (rate of voltage rise 5 kV/μs) L-N/N-PE/L-PE < 25ns/< 100ns/< 100ns L1-L2(N)/L2(N)-PE/L1-PE < 25ns
Max. continuous operating voltage UC L-N/N-PE 335VAC/260VAC L1-L2(N)/L2(N)-PE 280VAC
TOV test value UT
5s L-N/L-PE 350VAC/416VAC L-N/L-PE 350VAC/416VAC
200 ms N-PE 1200VAC N-PE 1200VAC
Rated frequency 50/60 Hz 50/60 Hz
Open circuit voltage UOC L-N/N-PE/L-PE 6kV L1-L2(N)/L2(N)-PE/L1-PE 6kV
Voltage protection level at UOC Up L-N/N-PE/L-PE 900V/1500V/900V L1-L2(N)/L2(N)-PE 900V
Nominal discharge current (8/20) μs In L-N/N-PE/L-PE 2.5kA L1-L2(N)/L2(N)-PE 5kA
Voltage protection level at In Up L-N/N-PE/L-PE 1000V/1500V/1000V L1-L2(N)/L2(N)-PE 950V
Max. discharge current (8/20) μs Imax L-N/N-PE/L-PE 10kA L1-L2(N)/L2(N)-PE/L1-PE 10kA
Follow current interrupt rating Ifi N-PE 100 Ar.m.s. –
Maximum back-up fuse
Maximum short-circuit current  125 AgL  C63
50 kAr.m.s. 10 kAr.m.s.

Connection diagram

x x

y y

Mechanical
Mechanical coding of base yx xx
Frame size 45 mm 45 mm
Device height 80 mm 80 mm
Device width 35 mm 35 mm
Weight 220 g 220 g
Permitted ambient temperature -40°C to +70°C -40°C to +70°C
Degree of protection (built-in) IP40 IP40
Upper and lower lift terminal capacity 1 - 25 mm2 1 - 25 mm2
Upper and lower open mouthed terminals for busbar thickness up to 1.5 mm 1.5 mm
Tightening torque of terminal screws 2.4 - 3 Nm 2.4 - 3 Nm
Quick fastening on DIN rail according to IEC/EN 60715 IEC/EN 60715

Dimensions (mm) Application Examples

26 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Photovoltaic - Surge Protection
Photovoltaic SPD Class T2 1.27
AC
DC
Max. continuous operating voltage Type Article No. Units per
UC Designation package

Plug-in Surge Arrester SPPVT2 for Photovoltaic application

• For insulationed and earthed systems
sg04914

600 V DC SPPVT2-06-2+PE 176088 1 / 40

1000 V DC SPPVT2-10-2+PE 176090 1 / 40

With auxiliary switch

600 V DC SPPVT2-06-2+PE-AX 176087 1 / 40
1000 V DC SPPVT2-10-2+PE-AX 176089 1 / 40

sg04714
Inserts for replacement
600 V DC SPPVT2-06 176091 1 / 50
1000 V DC SPPVT2-10 176092 1 / 50

27 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Photovoltaic - Surge Protection
1.28 Photovoltaic SPD Class T2

AC
DC

Description Plug-in Surge Arrester SPPVT2-...-2+PE(-AX)

• Increased safety through compliance with the EN 50539-11 standard
• Safe contacting thanks to integrated redary bolts
• Easy to replace thanks to a plug-type arrester
• Optimal protection of the inverter thanks to a low protection level
• Selective replacement of defective connectors thanks to a visual status indicator
• Optimized planning of maintenance interventions thanks to remote signalling (Type -AX)
• No wrong connecting possible thanks to coded connectors and base elements

Connection diagram
SPPVT2(H)-...-2+PE(-AX)
12 14

11 FM

L+ L–

Dimensions (mm)

28 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Photovoltaic - Surge Protection
Photovoltaic SPD Class T2 1.29
AC
DC

Technical Data
SPPVT2-06-2+PE(-AX) SPPVT2-10-2+PE(-AX)
Environmental condition
Degree of protection IP20 IP20
Ambient temperature of operation -40 ... +80°C -40 ... +80°C
Altitude  2000 m  2000 m
Allowed range of air humidity of operation 5 ... 95 % 5 ... 95 %
General
Standards/regulations EN 50539-11 EN 50539-11
EN Test class PV T2 PV T2
SPD failure performance OCM OCM
Mounting DIN rail 35 mm DIN rail 35 mm
Material of the enclosure PBT/PA PBT/PA
Pollution degree II II
Flammabilty class according to UL 94 V0 V0
Signal for surge protection defective visual, with remote signalling contact visual, with remote signalling contact
Predective circuit on the direct current side (DC)
Max. continuous operating voltage UCPV 800 V DC 1170 V DC
No-load output voltage UOCSTC  670 V DC  970 V DC
Short-circuit current strength ISCPV 2000 A 2000 A
Nominal load current IL 80 A DC 80 A DC
Predective conductor current IPE
DC  20 μA  20 μA
AC  300 μA  250 μA
Standby power consumption PC  20 mVA  25 mVA
Nominal discharge current (8/20) μs 15 kA 15 kA
Maximum discharge current (8/20) μs Imax 40 kA 40 kA
Total lightning discharge current (8/20) μs ITotal 40 kA 40 kA
Voltage protection level (L+) - (L-) Up  2.7 kV  3.7 kV
Voltage protection level (L+/L-) - PE Up  2.7 kV  3.7 kV
Responding time tA  25 ns  25 ns
Size
Hight 99 mm 99 mm
Width 53.4 mm 53.4 mm
Depth 65.5 mm 65.5 mm
Module units (MU) 3 MU 3 MU
Weight
...+PE gross 313 g / net 288 g gross 337 g / net 311 g
...+PE-AX gross 320 g / net 294 g gross 343 g / net 317 g
Connection data
Type of connection Screw connection Screw connection
Lift terminal capacity
flexible 1.5-25 mm2 1.5-25 mm2
solid 1.5-35 mm2 1.5-35 mm2
Bolt thread M5 M5
Tightening torque 4.5 Nm 4.5 Nm
Stripping length 16 mm 16 mm
Type of connection Biconnect-terminals Biconnect-terminals
Lift terminal capacity
solid 1.5-16 mm2 1.5-16 mm2
Bolt thread M6 M6
Tightening torque 30 lb in 30 lb in
Auxiliary Switch
Switching function CO, 1-pole CO, 1-pole
Rated operational voltage 5 ... 250 V AC, 30 V DC 5 ... 250 V AC, 30 V DC
Rated operational current 5 mA ... 1.5 A AC, 1.5 A DC 5 mA ... 1.5 A AC, 1.5 A DC
Type of connection MC 1.5/3 MC 1.5/3
Lift terminal capacity
flexible 0.14-1.5 mm2 0.14-1.5 mm2
solid 0.14-1.5 mm2 0.14-1.5 mm2
Lift terminal capacity AWG/kcmil 30 ... 14 30 ... 14
Bolt thread M2 M2
Tightening torque 0.25 Nm, 2 ... 4 lb in 0.25 Nm, 2 ... 4 lb in
Stripping length 7 mm 7 mm

29 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Photovoltaic - Surge Protection
1.30 Photovoltaic SPD Class T1/T2

AC
DC
Max. continuous operating voltage Type Article No. Units per
UC Designation package

Plug-in Surge Arrester SPPVT12 for Photovoltaic application

• For insulationed and earthed systems
sg04914

600 V DC SPPVT12-06-2+PE 177258 1 / 40

1000 V DC SPPVT12-10-2+PE 177256 1 / 40

With auxiliary switch

600 V DC SPPVT12-06-2+PE-AX 177257 1 / 40
1000 V DC SPPVT12-10-2+PE-AX 177255 1 / 40

sg04714
Inserts for replacement
600 V DC SPPVT12-06 177259 1 / 50
1000 V DC SPPVT12-10 177260 1 / 50

30 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Photovoltaic - Surge Protection
Photovoltaic SPD Class T1/T2 1.31
AC
DC

Description Plug-in Surge Arrester SPPVT12-...-2+PE(-AX)

• Increased safety through compliance with the EN 50539-11 standard
• Safe contacting thanks to integrated redary bolts
• Easy to replace thanks to a plug-type arrester
• Optimal protection of the inverter thanks to a low protection level
• Selective replacement of defective connectors thanks to a visual status indicator
• Optimized planning of maintenance interventions thanks to remote signalling (Type -AX)
• No wrong connecting possible thanks to coded connectors and base elements
• Always the right arrester thanks to universal Type1/Type2 predective components

Connection diagram
SPPVT12-...-2+PE(-AX)
12 14

11 FM

L+ L–

Dimensions (mm)

31 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Photovoltaic - Surge Protection
1.32 Photovoltaic SPD Class T1/T2

AC
DC

Technical Data
SPPVT12-06-2+PE(-AX) SPPVT12-10-2+PE(-AX)
Environmental condition
Degree of protection IP20 IP20
Ambient temperature of operation -40 ... +80°C -40 ... +80°C
Altitude  2000 m  2000 m
Allowed range of air humidity of operation 5 ... 95 % 5 ... 95 %
General
Standards/regulations EN 50539-11 EN 50539-11
EN Test class PV T1/PV T2 PV T1/PV T2
SPD failure performance OCM OCM
Mounting DIN rail 35 mm DIN rail 35 mm
Material of the enclosure PBT/PA PBT/PA
Pollution degree II II
Flammabilty class according to UL 94 V0 V0
Signal for surge protection defective visual, with remote signalling contact visual, with remote signalling contact
Predective circuit on the direct current side (DC)
Max. continuous operating voltage UCPV 720 V DC 1050 V DC
No-load output voltage UOCSTC 600 V DC  875 V DC
Short-circuit current strength ISCPV 2000 A 2000 A
Nominal load current IL 80 A DC 80 A DC
Predective conductor current IPE
DC  20 μA  20 μA
AC  350 μA  350 μA
Standby power consumption PC  20 mVA  25 mVA
Nominal discharge current (8/20) μs 15 kA 15 kA
Maximum discharge current (8/20) μs Imax 40 kA 40 kA
Lightning test current (10/350) μs, Peak current Iimp 5 kA 5 kA
Total lightning discharge current (8/20) μs ITotal 7 kA 5 kA
Voltage protection level (L+) - (L-) Up  2.6 kV  357 kV
Voltage protection level (L+/L-) - PE Up  2.6 kV  3.5 kV
Responding time tA  25 ns  25 ns
Required max. back-up fuse with stub-line wiring not neccessary not neccessary
Size
Hight 99 mm 99 mm
Width 53.4 mm 53.4 mm
Depth 65.5 mm 65.5 mm
Module units (MU) 3 MU 3 MU
Weight
...+PE gross 407 g / net 379 g gross 407 g / net 379 g
...+PE-AX gross 414 g / net 386 g gross 414 g / net 386 g
Connection data
Type of connection Screw connection Screw connection
Lift terminal capacity
flexible 1.5-25 mm2 1.5-25 mm2
solid 1.5-35 mm2 1.5-35 mm2
Bolt thread M5 M5
Tightening torque 4.5 Nm 4.5 Nm
Stripping length 16 mm 16 mm
Type of connection Biconnect-terminals Biconnect-terminals
Lift terminal capacity
solid 1.5-16 mm2 1.5-16 mm2
Bolt thread M6 M6
Tightening torque 30 lb in 30 lb in
Auxiliary Switch
Switching function CO, 1-pole CO, 1-pole
Rated operational voltage 5 ... 250 V AC, 30 V DC 5 ... 250 V AC, 30 V DC
Rated operational current 5 mA ... 1.5 A AC, 1.5 A DC 5 mA ... 1.5 A AC, 1.5 A DC
Type of connection MC 1.5/3 MC 1.5/3
Lift terminal capacity
flexible 0.14-1.5 mm2 0.14-1.5 mm2
solid 0.14-1.5 mm2 0.14-1.5 mm2
Lift terminal capacity AWG/kcmil 30 ... 14 30 ... 14
Bolt thread M2 M2
Tightening torque 0.25 Nm, 2 ... 4 lb in 0.25 Nm, 2 ... 4 lb in
Stripping length 7 mm 7 mm

32 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Photovoltaic - Surge Protection
Busbar 1.33
Poles Type Article No. Units per
Designation package

Busbar Z-GV-U/ for SPI, SP-B+C

2 Z-GV-U/2 272588 20 / 1200
3 Z-GV-U/3 272589 20 / 1200
Z-GV-U/9 4 Z-GV-U/4 274080 20 / 1200
5 Z-GV-U/5 274081 20 / 1200
6 Z-GV-U/6 274082 20 / 400
8 Z-GV-U/8 274083 20 / 200
9 Z-GV-U/9 274084 20 / 200

Description busbar Z-GV-U/

• Busbars Z-GV-U/ permit to implement customary SPD combinations
• Suitable for SPI-..., SPB-D-125
• The rated cross-section of Z-GV-U/ is 16 mm2
• The busbars must be cut to length in some cases

Technical Data
Z-GV-U/
Electrical
Rated voltage 230/400 V, 50/60 Hz
Rated current 63 A
Mechanical
Busbar cross section 16 mm2 Cu

Design

33 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Photovoltaic - Surge Protection
1.34 Busbar

Used for Type Article No. Units per

Designation package

Busbar Z-GV-16/3P-3TE/6
for SPI and SPC Z-GV-16/3P-3TE/6 267511 12 / 240
WA_SG11202

34 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Busbar 1.35
Poles Type Article No. Units per
Designation package

Busbar ZV-KSBI for SPC

2MU ZV-KSBI-2MU 263961 10 / 600
3MU ZV-KSBI-3TE 263962 10 / 600
3MU ZV-KSBI-3TE/S 263963 10 / 600
2MU+1.5MU ZV-KSBI-3TE+HI 112370 50 / 150
4MU ZV-KSBI-4TE 263964 10 / 600
5MU ZV-KSBI-5TE 263965 10 / 200
5MU ZV-KSBI-5TE/N 263966 10 / 200
2MU+3x1.5MU ZV-KSBI-5TE+HI 112371 50 / 150
6MU ZV-KSBI-6TE 113118 50 / 500
7MU ZV-KSBI-7TE 263967 50 / 500
7MU ZV-KSBI-7TE/S 263968 10 / 100
7MU ZV-KSBI-7TE/N 263969 10 / 100
9MU ZV-KSBI-9TE/N 266874 50 / 500
11MU ZV-KSBI-11MU 263970 50 / 500

Description busbar ZV-KSBI

• With the ZV KSBI busbar bracket you can realize the common combinations of arrestors.
• Used for SPB-..., SPC-..., Z-D63
• The rated cross-section of the ZV-KSBI bridge metals is 16 mm2
• The busbar mounting bracket can be shortened

Technical Data
Z-GV-U/
Electrical
Rated voltage 230/400 V, 50/60 Hz
Rated current 63 A
Mechanical
Busbar cross section 16 mm2 Cu

Design

35 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
1.36 Surge Protective Class T3 (formerly D)

Description Type Article No. Units per

Designation package

19” Multiple Outlet Strips NWS-STL/19/7F

7outlets, DIN NWS-STL/19/7F 255398 1
N00411

7outlets plus switch, DIN NWS-STL/19/7F/S/BL 255399 1

7outlets, UTE NWS-STL/19/7F/UTE 290031 1

Description 19” Multiple Outlet Strips NWS-STL/19/7F

• Installation onto 19” rails
• Installation height: 1U
• Diagonally arranged socket outlets with earthing contact according to DIN 49440 or NF-C61314 (UTE), 16 A / 250 V AC
• Connection cable of 2.5 m H05VV-F 3G 1.5 mm2 with an angled connector
• Max. power consumption: 3680 W
• Degree of protection: IP20
• Temperature range: -5 to +40 °C
• Dimensions: 482.6x44x44.45 mm (WxDxH)
• Material: Enclosure made of aluminium, front cover made of plastic similar to RAL 7035
• Weight: approx. 0.9 kg
• Scope of delivery: 1 Outlet strip incl. 19“ fixing bracket, different fixing material

19“ Multiple Outlet Strips with Surge Protection SPD-STL/19/7F-S/BL

7outlets plus switch,, DIN SPD-STL/19/7F-S/BL 283449 1
wa_nt06613

7outlets, UTE SPD-STL/19/7F-S/BL/UTE 290032 1

Description 19“ Multiple Outlet Strips with Surge Protection SPD-STL/19/7F-S/BL

• Can be mounted on 19“ rails
• Installation height: 1U
• Diagonally arranged socket outlets with earthing contact according to DIN 49440 or NF-C61314 (UTE), 16 A / 250 V AC
• Connection cable of 2.5 m H05VV-F 3G 1.5 mm2 with an angled connector
• On/Off switch, 2-pole, lit
• Max. power consumption: 3680 W
• Degree of protection: IP20
• Temperature range: -5 up to +40 °C
• Surge protection tested according to IEC 61643-1 (Class: SPD Type 3)
• Response time: < 25 ns
• Dimensions: 482.6x44x44.45 mm (WxDxH)
• Material: Enclosure made of aluminium, front cover made of plastic similar to RAL 7035
• Weight: approx. 0.9 kg
• Scope of delivery: 1 Outlet strip incl. 19“ fixing bracket, different fixing material

36 EATON CORPORATION xxxxx+xxxx-xxxxEN

 Surge Protection
Surge Protective Class T3 (formerly D) 1.37
Description Type Article No. Units per
Designation package

Surge Protection Multiple Outlet Strips with High-Range Filter and Energy Absorption for full
Equipment Protection SPD-STL/6F-S
6outlets plus switch, DIN SPD-STL/6F-S (68583) 130000 1
N04011

6outlets plus switch, DIN+ISDN SPD-STL/6F-S/ISDN (68585) 147795 1

19“ fixing bracket for SPD-STL/6F-S (1U) NWS-HW/19/SPD-STL/6F-S 166364 1

Description Surge Protection Multiple Outlet Strips with High-Range Filter and Energy Absorption for full Equipment
Protection SPD-STL/6F-S
• Suitable for wall-mounting in indoor areas
• A 19“ fixing bracket is available as an option for mounting the strip in a cabinet
• Diagonally arranged socket outlets with earthing contact according to DIN 49440, 10 A / 250 V AC
• Connection cable of 1.0 m H05VV-F 3G 1.0 mm2 with an angled connector
• On/Off switch with MCB that can be reset
• Max. power consumption: 2500 W
• Degree of protection: IP20
• Temperature range: -15 to +70 °C
• Surge protection tested according to IEC 61643-1 (Class: SPD Type 3)
• Response time: < 1 ns
• Dimensions: 390x42x52 mm (WxDxH)
• Material: Enclosure made of plastic similar to RAL 7021
• Weight: approx. 0.4 kg
• Scope of delivery: 1 Multiple outlet strip

37 EATON CORPORATION xxxxx+xxxx-xxxxEN

Eaton is a power management company with 2017 sales of $20.4 billion.
We provide energy-efficient solutions that help our customers effectively
manage electrical, hydraulic and mechanical power more efficiently,
safely and sustainably. Eaton is dedicated to improving the quality of life
and the environment through the use of power management
technologies and services. Eaton has approximately 96,000 employees
and sells products to customers in more than 175 countries.

For more information, visit Eaton.com.

To contact us please visit http://www.eaton.eu/Europe/

Electrical/CustomerSupport/ContactDetails/index.htm
For Technical support please get in contact with
techsupportemea@eaton.com

Eaton Industries (Austria) GmbH

Scheydgasse 42
1210 Vienna
Austria

Changes to the products, to the information contained in this

document, and to prices are reserved; so are errors and omissions.
Eaton Only order confirmations and technical documentation by Eaton is
EMEA Headquarters binding. Photos and pictures also do not warrant a specific layout or
Route de la Longeraie 7 functionality. Their use in whatever form is subject to prior approval
1110 Morges, Switzerland by Eaton. The same applies to Trademarks (especially Eaton, Moeller,
Eaton.eu and Cutler-Hammer). The Terms and Conditions of Eaton apply, as
referenced on Eaton Internet pages and Eaton order confirmations.
© 2019 Eaton
All Rights Reserved
Printed in Austria Follow us on social media to get the
Publication No. Eaton is a registered trademark. latest product and support information.
Article number ......-MK
January 2019 All other trademarks are property
Grafics: SRA, Schrems of their respective owners.