PM500

User Manual
Original Instructions
PowerMonitor 500 Unit

Catalog Numbers 1420-V1, 1420-V2, 1420-V1A, 1420-V1P, 1420-V2A, 1420-V2P, 1420-V1-ENT, 1420-V1-485, 1420-V2-
ENT, 1420-V2-485, 1420-V1A-ENT, 1420-V1A-485, 1420-V2A-ENT, 1420-V2A-485, 1420-V1P-ENT, 1420-V1P-485, 1420-
V2P-ENT, 1420-V2P-485
Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and
operation of this equipment before you install, configure, operate, or maintain this product. Users are required to
familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws,
and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are
required to be carried out by suitably trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may
be impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from
the use or application of this equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and
requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or
liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or
software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation,
Inc., is prohibited
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous
environment, which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT Identifies information that is critical for successful application and understanding of the product.
Labels may also be on or inside the equipment to provide specific precautions.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to
potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL
Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).
Table of Contents
Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Intended Audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Catalog Number Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Access Product Release Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 1
PowerMonitor 500 Unit Overview About the PowerMonitor 500 Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PowerMonitor 500 Features and Functions . . . . . . . . . . . . . . . . . . . . . . 8
Front Panel Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Display Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Selecting Data to Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 2
Installation and Wiring Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Wiring Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 3
Unit Configuration Configure with the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Configuration Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Digital Filtering Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Analog Output Configuration Examples . . . . . . . . . . . . . . . . . . . . . . . . 36
Alarm Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Chapter 4
Communication EtherNet/IP Communication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Modbus Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Appendix A
PowerMonitor 500 Unit Data Summary of Data Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Tables Geometric Representation of Power and Power Factor . . . . . . . . . . . 50
Data Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Appendix B
Technical Specifications List of Connectable Variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 3

Table of Contents
Appendix C
PowerMonitor 500 EtherNet/IP General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Device Profile Object Model and Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Identity Object - CLASS CODE 0x0001. . . . . . . . . . . . . . . . . . . . . . . . 77
Assembly Object - CLASS CODE 0x0004 . . . . . . . . . . . . . . . . . . . . . . 82
Technical Notes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Appendix D
Unit Configuration - Base Configure with the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Firmware Revision 11 and Earlier Configuration Flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95
4 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

Preface
About This Manual This manual contains detailed information on these topics:
• Mounting and wiring of the unit
• Wiring to native and optional communication port
• Set-up and use of the display module
• Information on metering functionality and measurements
• Use of the display module for configuration, monitoring, and
commands
• Discussion of communication options, functionality, configuration, and
operation
• Alarm configuration and operation
• PowerMonitor™ 500 data tables
Summary of Changes This manual contains new and updated information as indicated in the
following table.
Topic Page
Updated the configuration flowchart order for units with base firmware 12 and Chapter 3
later.
Moved the configuration flowchart for units with base firmware revision 11 or Appendix D
earlier to an appendix.
Intended Audience This manual is intended for qualified personnel. You need a basic
understanding of electric power and energy theory and terminology, and
alternating-current (AC) metering principles.
Catalog Number Explanation
1420 -V1 P -485
Bulletin Number Voltage Auxiliary Optional Comms

1420 - PowerMonitor 500 V1 - 240V AC V-LL P - Pulse (Digital) Output 485 - Serial RS-232,
120V AC V-LN/208V AC V-LL A - Analog Output RS-485, Modbus RTU
V2 - 400V AC V-LN and Blank - No Output ENT - EtherNet/IP
690V AC V-LL and Modbus TCP/IP
Blank - No Comm

Preface
Access Product Release Notes Product release notes are available online within the Product Compatibility
and Download Center.
The latest PowerMonitor 500 unit Ethernet firmware is found at the following
website:
http://compatibility.rockwellautomation.com/Pages/MultiProductDownload.aspx.
1. From the Product Compatibility and Download Center, search for your
product or choose Energy Monitoring from the All Categories pull-
down menu.
2. Select your product and firmware revision and click Downloads.
3. Click the download icon to access product release notes.
Additional Resources These documents contain additional information concerning related products
from Rockwell Automation.
Resource Description
Industrial Automation Wiring and Grounding Guidelines, Provides general guidelines for installing a Rockwell
publication 1770-4.1 Automation industrial system.
Product Certifications website, http:// Provides declarations of conformity, certificates, and
www.rockwellautomation.com/global/certification/ other certification details.
overview.page
You can view or download publications at

http://www.rockwellautomation.com/global/literature-library/overview.page.
To order paper copies of technical documentation, contact your local
Allen-Bradley distributor or Rockwell Automation sales representative.

Chapter 1
PowerMonitor 500 Unit Overview
About the PowerMonitor 500 The PowerMonitor™ 500 unit is an AC power monitor with a built-in
advanced configuration system and LCD data display. The unit is designed for
Unit measurement of electrical parameters in various three-phase, single-phase
(2-wire European), and split-phase (3-wire North American single phase)
circuits. The unit modular housing can be mounted in a panel that provides
IP65 degree protection from the front. The power monitor can be provided
with analog or digital (relay) outputs. These outputs can be selected to output a
pulse proportional to the real and reactive energy that is measured, or to
annunciate alarms. The instrument can also be equipped with a serial RS-485/
RS-232 port or an EtherNet/IP port.
Equipped with an optional communication port, the unit communicates

power and energy parameters to applications, such as FactoryTalk®
EnergyMetrix™ software. The power monitor works with these software
applications to address these key customer applications:
• Load profiling - log power parameters such as real energy, apparent
power, and demand, for analysis of power usage by loads over time
• Cost allocation - report actual energy cost by department or process to
integrate energy information into management decisions
• Billing and sub billing - charge users of energy the actual usage cost
rather than allocating by square footage or other arbitrary methods
• Power system monitoring and control - display and control power flow
and energy utilization

Chapter 1 PowerMonitor 500 Unit Overview
PowerMonitor 500 Features The power monitor connects to your three-phase, split-phase (3-wire North
American single phase), or single-phase (2-wire European) AC power system
and Functions directly or through instrument transformers (PTs and CTs). It converts
instantaneous voltage and current values to digital values, and uses the resulting
digital values in calculations of voltage, current, power, energy, and demand.
The power monitor family includes several models that combine the following
basic components:
• A panel-mounted power monitor in one of two AC voltage ranges:
120/208V or 400/600V
• An optional pair of digital (relay) outputs
• An optional pair of 0…20 mA analog outputs
• Optional serial RS-232/RS-485 communication supporting Modbus
RTU
• Optional Ethernet port supporting EtherNet/IP and Modbus TCP/IP
• Front protection degree: IP65, NEMA 4X, NEMA 12
• Up to four configurable virtual alarms
• Class 1 (kWh) according to EN62053-21
• Class B (kWh) according to EN50470-3
• Class 2 (kVARh) according to EN62053-23
• Accuracy ±0.5% of reading (current/voltage)
• Metering values display: Four rows with 4 digits
• Energy value display: Ten digits and the plus/minus sign
• Three-phase (system) variables: V(L-L), V(L-N), A, VA, W, VAR,
power factor, frequency
• Single phase variables: V(L-L), V(L-N), A(L), An (calculated), VA, W,
VAR, power factor
• System and single phase average and maximum variables
• Energy measurements (imported/exported): kWh and kVARh
• Revenue grade energy measurements per ANSI C12.1 Class 1.0, ANSI
C12.1
• Run hours counter (8+2 digits)
• Real-time clock function
• Universal power supply: 120/240V AC 50/60 Hz, or 120/240V DC
• Front dimensions: 96 x 96 mm (3.78 x 3.78 in)

PowerMonitor 500 Unit Overview Chapter 1
Front Panel Features This section describes the front panel of the unit.
Front Panel Indicators and Control Buttons

The buttons are enhanced touch buttons. The touch icon turns on each time a
button is pressed. We recommend using your forefinger to activate the touch
buttons.
In Metering mode, buttons 4 and 5 (shown in Figure 1) are used to display the
maximum and demand (average) values of the displayed measurements.
Figure 1 - Front Panel
1 6
PowerMonitor 500
Display Item Description

1 Active Alarms AL1…AL4 status indicators.
2 Real Energy consumption-rate status indicator. Faster flashing indicates higher rate of consumption. Maximum frequency 16 Hz per EN5047-1.
3 Exit Button - Press quickly to exit submenus, or to exit the programming menus in Programming mode.
When in the programming menu, press and hold Exit for at least 2 seconds to exit the programming menu. Press Program/select to confirm and return to the
metering display and exit the programming menu without saving your changes.
To save changes, use the Up and Down arrows to go to the End menu, then press Program/Select.
When not in the programming menu, press and hold for more than 2 seconds to view the information pages.
In Metering mode, press quickly to scroll through the energy counters.
4 Up Button - Press the Up button to browse menus and to increase values to be set.
5 Down Button - Press the Down button to browse menus and to decrease values to be set.
6 Program/select Button - Press and hold the Program/select button for at least 2 seconds to access the programming menu.
When in the programming menu, press Program/select to confirm the programmed values in the active page. Press Program/select to enter and exit edit mode
on the active page.
When not in the programming menu, press Program/select to select measured values for display. Press quickly to scroll through the metering display pages.
See Table 1 and Table 2 for a list of the measurement screens.

Additional Button Functions
Certain buttons have two functions. To access the second function, press and
hold the button for more than 2 seconds.
Displays PowerMonitor 500 information screens, which provide reference

standards, firmware revision, and year of manufacture.
Resets the max (maximum) of the displayed variables. You must press
Program/select to confirm the reset.
Resets the dmd (demand) of the displayed variables. You must press
Program/select to confirm the reset.

Display Features Figure 2 - Features

9 6
7
ROW 1
10 11
1
ROW 2
8
2
ROW 3
3
ROW 4
4 12
ROW 5
5

1 Phase displacement indicator: inductive L, -L, or capacitive C, -C.
The sign is based on the direction of real power flow.
Positive = consuming power, negative = generating power.
See the Geometric Representation of Power and Power Factor in Appendix A for more information.
In Programming mode, the indicator displays E when a parameter can be edited.
2 Indicates the measured value phase (line-to-neutral L1 or line-to-line L12).
5 Engineering unit and multiplier indicator (k, M, V, W, A, var, PF, Hz, An).
6 ALR: the alarm display function is active. PROG: the programming function is active.
7 Area set aside for energy counters (see Table 1), text messages, date and time (format: dd.mm.yy/hh:mm).
8 Indicates that metering values are dmd (demand) or MAX (maximum) values.
Display Icons
9
9 Indicates that the metering values displayed are system (three-phase) values.
10 10 Indicates a phase sequence error alarm for Voltage rotation.
11 Configuration lock switch is not active. Always indicates unlocked.
11 12 Indication of serial RS-485/RS-232 data transmission (TX) and reception (RX).
12
Alarm Icons
• Indicates a high value alarm
• Indicates a low value alarm

Selecting Data to Display Table 1 and Table 2 provide a guide to navigation through the metering data
displays available on the front panel display. Row 1…Row 5 indicate the rows of
the display (see Figure 2 on page 11).
Press for <2 seconds to cycle through the data that is displayed in Row
1 of the display.
Selected data for Row 1 remains displayed until is pressed.
Table 1 - Row 1 Data

Parameters 1 2 3 4 5 6 7 8 9 10
Row 1 Total kWh Total kVARh Total kWh (- Total kVARh kWh (+) kVARh (+) kWh (-) kVARh (-) Run Hours RTC
(+) (+) ) (-) part. part. part. part. (99999999.99)
Press for <2 seconds to cycle through the data that is displayed in
Rows 2…5 of the display.
Selected data for Rows 2…5 displays momentarily and then returns to the
default display.
Use and to cycle through the max, instantaneous, and

demand (dmd) values.
IMPORTANT The appropriate data is displayed based on the configured system. For
example, for delta (3P) systems, individual line data is not displayed for line-
to-neutral voltage, VA, VAR, W, and power factor.
Table 2 - Rows 2…5 Data

Parameters 0 1 2 3 4 5 6 7
Set
Row 2 V LN Σ V LL Σ An Hz VA Σ VAR Σ WΣ PF Σ
Row 3 V L1 V L1-2 A L1 - VA L1 VAR L1 W L1 PF L1

To access information pages, press and hold for more than 2 seconds,
then press and to select information items, as shown in

Table 3. After a period of inactivity, the information pages close, and the
display returns to the default screen.
IMPORTANT Information items are not displayed for options that are not installed. For
example, a module that does not have the analog output option does not
display analog parameters (columns 11 and 12 in Table 3).
Table 3 - Rows 1…5 Information Pages

Page 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
No.
Row Serial Conn. Status Pulse Pulse Remote AL1 AL2 AL3 AL4 Analog Analog2 COM IP XX•XX•X
1 Number xxx Indicator OUT1 OUT2 out(1) 1(1) (1)
port(1) Address X XX:XX
(9 (3PN/ Pulse kWh/ kWh/ (Real-
digits) 3P/3P1/ kWh kVARh kVARh(1 time
(1) )
3P2/1P/ clock)
2P)
Row Yr. xx CT.rA 0.001… 0.001 xxxx Out 1 Variable Variable Variable Variable Hi.E(2) Hi.E(2) Add XXX XXX dAtE
2 1000 …1000 kWh/
kWh per kWh/ kVARh
pulse kVARh per
per pulse
pulse
Row rEL 1.0…9 +/- tot/ +/- tot/ on/oFF Set 1 Set 1 Set 1 Set 1 0.0… 0.0… 1…247 XXX tiME
3 9.99k PAr PAr 9999k 9999k
Row A.10 Pt.rA Out2 Set 2 Set 2 Set 2 Set 2 Hi.A(3) Hi.A(3) bdr XXX
4
Row 1…60 1.0…9 on/oFF (measur (measur (measur (measur 0.0… 0.0… 9.6/ XXX
5 (min) 999 ement) ement) ement) ement) 100.0% 100.0% 19.2/
‘dmd’ 38.4/
115.2
(1) If appropriate option is selected.
(2) Hi.E corresponds to the configured Max Input for the analog output.
(3) Hi.A corresponds to the configured Max Output for the analog output.

Figure 3 and 4 are examples of how the information pages are displayed.
Figure 3 - Information Page 2
Row 1
Row 2
Row 3
Row 4
Row 5
PowerMonitor 500
Figure 4 - Information Page 15
Row 1
Row 2
Row 3
Row 4
Row 5
PowerMonitor 500

Chapter 2
Installation and Wiring
Installation This section shows the dimensions of the unit for installation in a panel.
Figure 5 - Base Unit Dimensions
89.97 mm
96.00 mm (3.54 in.)
(3.78 in.) 93.00 mm
(3.66 in.)
96.00 mm
(3.78 in.) 20.20 mm 29.70 mm
(0.80 in.) (1.17 in.)
Figure 6 - Panel Cut-out
91.00 mm
(3.58 in.)
Figure 7 - Factory-installed Optional Modules

Digital and Analog Output Modules Serial and Ethernet Communication Modules
62.99 mm 62.99 mm
(2.48 in.) (2.48 in.)
16.00 mm 20.00 mm
89.49 mm (0.63 in.) 89.49 mm (0.79 in.)
(3.52 in.) (3.52 in.)

Chapter 2 Installation and Wiring
Figure 8 - Installation in Panel
Figure 9 - Rear View of Unit Showing Wiring Terminals
Power Supply

Installation and Wiring Chapter 2
Wiring Diagrams The PowerMonitor™ 500 unit can monitor various three-phase, single-phase,
and split-phase circuits. Select the voltage connections, current wiring, and
system metering mode to match the configuration of the circuit being
monitored.
Table 4 provides a key for you to select the proper wiring diagrams and system
metering modes.
Table 4 - Wiring Diagram Explanation
Circuit type No. of CTs No. of PTs Wiring Diagram System
Configuration
3-phase, 4-wire Wye Unbalanced load 3 - Figure 12 3P.n
3 3
3-phase, 2-wire Wye Balanced load 1 - Figure 11 3P.2
1 1
3-phase, 3-wire Delta Unbalanced load 3 - Figure 13 3P
2 -
Open Delta Unbalanced load 3 2 Figure 13 3P
2 2
Open Delta Balanced load 1 2 Figure 14 3P.1
3-phase, Single CT Balanced load 1 - Figure 14 3P.1
1 3
Split-phase 2 - Figure 15 2P
2 2
Single phase 1 - Figure 16 1P
1 1
The wiring diagrams in this manual are drawn with U.S. (NEMA) conventions.
For convenience, a connection diagram is shown in IEC style on the left and in
its corresponding NEMA style (used in the U.S.) on the right.
Figure 10 - Wiring Diagram Interpretation

These diagrams are simplified. Wiring of the power monitor must comply with
all applicable codes, standards, and regulations. Protect voltage and control
power wiring with suitable overcurrent protection. Connect current
transformer (CT) secondary wiring through a suitable shorting terminal block.
IMPORTANT In these diagrams, ‘balanced load’ configurations permit 3-phase

measurement by using only one phase connection. Unbalance in the
measured circuit affects the accuracy of the measurements.
Figure 11 - 3-phase, 2-wire Wye, Balanced Load

Meter Configuration: System = 3P.2
Line Line
PM 500 PM 500
L1 L2 L3 N L1 L2 L3 N PT
Fuse Fuse (VT )
L1 L1
N N
Shorting Shorting
terminal block terminal block Ground
S1 S1
CT CT
I1 I1
1 1
S2 S2
Load Load
Ground Ground
1-CT Connection 1-CT and1-PT/VT Connections
Figure 12 - 3-phase, 4-wire Wye, Unbalanced Load

Meter Configuration: System = 3P.n
Line
PM 500
L1 L2 L3 N PT 1
Fuse (VT 1)
L1
Line
PM 500
L1 L2 L3 N
PT 2
Fuse (VT 2)
Fuse
L1
L2
Fuse
L2
PT 3
Fuse Fuse (VT 3)
L3 L3
N
N
Shorting Shorting Ground

terminal block terminal block
S1 S1
CT CT
I1 I1
1 1
S2 S2
S1 S1
CT CT
I2 I2
2 2
S2 S2
S1 S1
CT CT
I3 I3
3 3
S2 S2
Load Ground Load Ground

Figure 13 - 3-phase, 3-wire Delta, Unbalanced Load

Meter Configuration: System = 3P
Line
Line PM 500
PM 500 L1 L2 L3 PT 1
L1 L2 L3 Fuse (VT 1)
Fuse L1
L1
Fuse Fuse
L2 L2
Fuse
Fuse
L3
L3
PT 3
N (VT 3)
Ground N
Shorting Shorting
S1 S1
CT CT
I1 I1
1 1
S2 S2
S1 S1
CT CT
I2 I2
2 2
S2 S2
S1 S1
CT CT
I3 I3
3 3
S2 S2
3-CT Connection 3-CT and2-PT/VT Connections (Open Delta)

Line
Line PM 500
PM 500 L1 L2 L3 PT 1
L1 L2 L3 Fuse (VT 1)
Fuse L1
L1
Fuse Fuse
L2 L2
Fuse
Fuse
L3
L3
PT 3
N (VT 3)
Ground N
Shorting Shorting
S1 S1
CT CT
I1 I1
1 1
S2 S2
S1 S1
I2 I2
S2 S2
S1 S1
CT CT
I3 I3
3 3
S2 S2
2-CT Connection (ARON) 2-CT and2-PT/VT Connections (ARON) (Open Delta)
Figure 14 - 3-phase, Single CT, Balanced Load

Meter Configuration: System = 3P.1
Line
PM 500
L1 L2 L3 N PT 1
Fuse (VT 1) Line
L1 PM 500
Line L1 L2 L3 PT 1
PM 500 Fuse (VT 1)
L1 L2 L3 N
PT 2 L1
Fuse (VT 2)
Fuse
L1
L2 Fuse
Fuse L2
L2
PT 3
Fuse (VT 3) Fuse
Fuse
L3 L3
L3
PT 3
N (VT 3)
N N
Ground
Shorting Shorting Ground Shorting
terminal block terminal block terminal block
CT CT CT
S1 S1 S1
I1 I1 I1
S2 S2 S2
Load Load Load

Ground Ground Ground
1-CT Connection 1-CT and3-PT/VT Connections 1-CT and2-PT/VT Connections

(Open Delta with balanced load)

Figure 15 - Split-phase
Line
Line L1 L2 N PM 500
PT 1
L1 L2 N PM 500 Fuse (VT 1)
L1
Fuse
L1
PT 2
Fuse (VT 2)
Fuse
L2
L2
N N
Shorting Shorting
S1 S1
CT CT
I1 I1
1 1
S2 S2
S1 S1
CT CT
I2 I2
2 2
S2 S2
Load Load
Ground Ground
Figure 16 - Single-phase
Line PM 500 Line PM 500

L1 N L1 N PT
Fuse Fuse (VT )
L1 L1
N N
Shorting Shorting
CT CT
S1 S1
I1 I1
S2 S2
Load Load
Ground Ground

Supply Power
Connect the PowerMonitor™ 500 unit to a source of supply power through

user-provided disconnecting means, such as a switch or circuit breaker close to
the power monitor. Provide overcurrent protection that is sized to protect the
wiring. Apply supply power only after all wiring connections are made to the
unit.
Figure 17 - Supply Power

120/240V AC 50/60Hz, or 120/240V DC
PowerMonitor 500
+ -
1 2
-
+
F = 250V (T) 630 mA
Factory Installed Option Wiring

Figure 18 - Pulse (digital) Outputs (P option)
1 2 3 4 5 6 7 8
Out 1 Out 2
Out 1 Out 2
Figure 19 - Analog Outputs (A option)
Analog 20 mA DC
Out 1 Out 2
t1 t2
Ou Ou 1 2 3 4

Figure 20 - Serial RS-485 and RS-232 Communication Wiring (485 option)

RS-485 Port RS-232 Port
8 8 8
7 7 7
6 6 6
4 4 4
3 3 3
Mandatory
2 2 2
Termination
1 1 1
T = Termination
A- = Transmit minus
B+ = Transmit plus
IMPORTANT Additional devices that are provided with RS-485 are connected in parallel.
The termination of the serial output is implemented only on the last
instrument of the network, with a jumper between (B+) and (T). The
jumper applies an internal termination resistance between (A-) and (B+).
The RS-232 and
RS-485 communication ports cannot be connected and used
simultaneously.

Figure 21 - Ethernet Communication (ENT option)
Ethernet Network Switch Uplink to LAN
PowerMonitor 500 PowerMonitor 500
The PowerMonitor 500 unit connects to industry-standard Ethernet hubs and

switches by using standard CAT-5 UTP (unshielded twisted-pair) cables with
RJ45 connectors. Table 5 shows the cable and connector pin assignments.
Table 5 - Ethernet Network Connections
Terminal Signal
1 TX+
2 TX-
3 RX+
4
5
6 RX-
7
8

Notes:

Chapter 3
Unit Configuration
TIP For configuration of units with base firmware revision 11 and earlier, see
Appendix D.
Configure with the Display The PowerMonitor™ 500 unit provides menu-based configuration
(programming) by using its front panel display. The programming menus let
you select parameters to edit, select digits within parameters, and increase or
decrease the value of each digit.
Place the unit in Programming mode by pressing Program/select (8) for about
2 seconds. The front panel displays the PASSWORD? menu page 0 in Editing
mode. Enter the correct password by using the Up and Down arrows (the
default password is 0) and press Program/select. The front panel then displays
the BACKLIGHT menu page 10.
See the programming flowchart that begins on page 28 for a view of the
organization of programming menus and submenus. Each page is identified
with a number, which is displayed in the top right corner. Menu page numbers
end in zero, while submenu pages end in 1 through 9. For example, the System
page is menu 40. Likewise, the Dmd page is menu 70, and the demand interval
Time page is menu 72.
While you are programming the power monitor, the display items and control
buttons function one way when you are navigating between menu or submenu
pages, and another way when you are editing a menu page.

Chapter 3 Unit Configuration
Figure 22 - Front Panel Display
3
6
4
5 7
Table 6 - Front Panel Display Descriptions

Display Item Description Navigating Menus Editing a Menu
1 Programming mode indicator Indicates programming mode.
2 Programming menu page Identifies the current programming menu page. See the programming flowchart that begins on page 28.
3 Editing mode indicator Does not appear. Indicates the parameter being edited.
4 Cursor Does not appear. Appears beneath the digit currently being edited.
5 Permitted range Displays the permitted range of values for the selected parameter.
6 Exit button • When in a menu page, exits Programming mode • Moves the cursor one digit to the left.
without saving changes. Program/select button • When the leftmost digit is selected, dP is
confirms exit. indicated and you can change the decimal point
• When in a submenu page, exits to menu page. and multiplier (see Edit Decimal Point and
Multiplier on page 27).
• When held for at least 2 seconds, cancels the edit
and restores the previous value of the selected
parameter.
7 Up button Selects the next higher-numbered menu or • Increments the value of the digit indicated by the
submenu page. cursor.
• When dP is indicated, increments the decimal
point and multiplier.
Down button Selects the next lower-numbered menu of submenu • Decrements the value of the digit indicated by
page. the cursor.
• When dP is indicated, decrements the decimal
8 Program/select button • Press and hold for 2 seconds to enter the Program Stores the new value of the selected parameter, but
mode. does not save the new configuration to the power
• Selects a menu page for editing. monitor.
• When in a menu page with submenus, displays
the first submenu page.
• After pressing the Exit button, confirms exit from
Programming mode without saving changes.
• From SAVE menu page 260, saves new
configuration and exits Programming mode.

Unit Configuration Chapter 3
IMPORTANT To save programming changes, navigate to the SAVE menu page 260 and
press Program/select. To exit the Programming mode without saving any
changes, press Exit and confirm by pressing Program/select. If no buttons
have been pressed for 2 minutes, the power monitor exits Programming
mode without saving any changes.
TIP You can make programming changes by using the PowerMonitor 500
software.
Edit Decimal Point and Multiplier

When the cursor is beneath the last digit on the left, pressing Exit (6) lets you
change the decimal point and the multiplier (9) (k or M). The blinking ‘dP’
(decimal point) text (10) indicates this capability.
10
To modify the decimal point position and the multiplier, use the Up and
Down arrow (7) to select the desired value.

Configuration Flowchart The following flowchart shows the configuration menus and submenus that
are accessed through the display. To navigate through the menu pages, use the
up and down arrows. To enter Edit mode or to access a submenu, press the
Program/select button. The menu pages available depend on your module
type.
• 0 PASSWORD?: enter password by using up and
down arrows to change the digit. Use the Exit button
to move the cursor between digits. Press the
Program/select button to confirm password. The
default password is 0.
• 10 BACKLIGHT: adjusts backlight time from 0…255
minutes (0 = always on).
•
• 40 SYSTEM: this function lets you select the type of
electrical system.
See pages 17…20 for descriptions and wiring
diagrams that correspond to the system type
designations, such as, 3P and 3P.n.
• 50 CT RATIO: this function lets you select the value
of the CT ratio (primary/secondary ratio of the
current transformer being used). Example: if the CT
primary (current transformer) has a current of 300 A
and the secondary a current of 5 A, the CT ratio
corresponds to 60 (300 divided by 5).
• 60 PT RATIO: this function lets you select the value
of the PT (VT) ratio (primary/secondary ratio of the
potential/voltage transformer being used). Example:
if the primary of the connected PT is 20 kV and the
secondary is 100V, then the PT ratio corresponds to
200 (20,000 divided by 100). If the voltage level is
such that PTs are not required and are not in place,
configure the PT ratio to 1.0.

• 70 DMD: This function lets you select the

calculation method of the DMD/AVG value of the
selected variable.
– 71 TYPE: select the type of Calculation mode to
be used for the DMD/AVG calculation.
FIXED: The instrument calculates the
AVG/DMD value of the measured variable over
the selected interval, updates the AVG/DMD
value at the end of the interval, then resets and
starts a new calculation.
SLIDE: When first configured, the instrument
calculates the AVG/DMD value and updates its
value at the beginning after the first selected
interval. After the first interval, the instrument
calculates the AVG/DMD value every minute.
After the calculation, the instrument generates a
window whose width is the selected interval and
Fixed
that moves forward every minute.
– 72 TIME: select the time interval for the DMD/
AVG calculation. Default is 15 minutes.
– 73 SYNC: select the Synchronization mode.
That mode is the method that controls the
calculation method of the average/demand
according to the selected time.
Where:
Pmax is the maximum power
Pc is the contractual power • 100 FILTER: The digital filter makes it possible to
t1 is the selected time period for the calculation of the AVG/DMD value
stabilize the display of fluctuating measurements.
Slide
See Digital Filtering Operation on page 33.
– 101 FILTER S: set the operating range (span) of
the digital filter. The value is expressed as a %
(filter to 0.0 means filter excluded).
– 102 FILTER CO: set the filtering coefficient of
the instantaneous measures. By increasing the
value, also the stability and the settling time of the
measures are increased.
IMPORTANT: Some specific menus display only if the relevant
modules are installed.

• 110 RS232-485: User settings for the RS-232 and

RS-485 serial communication ports.
• 120 ETHERNET: User settings for the Ethernet
communication port.
• 140 VIRT AL 1: This virtual alarm function lets you
set the alarm parameters.
-IP ADDRESS www.xxx.yyy.zzz – 141 ENABLE: enable (YES) or disable (NO) the
-SUBNET www.xxx.yyy.zzz alarm.
ETHERNET -GATEWAY www.xxx.yyy.zzz
– 142 VARIABLES: set the variable to be linked to
the alarm.
-TCP IP PRT 1…9999 (default = 502)
– 143 SET 1: set the on alarm set point of the
-ACD yes/no (default = no) variable.
– 144 SET 2: set the off alarm set point of the
variable.
list of available
variables – 145 ON DELAY: set a delay on activation of the
alarm.
• 180 DIG OUT 1: This function lets you link a
virtual alarm to the digital relay output and to its
working parameters.
– 181 FUNCTION:
Same as VIRT ALARM 1
Alarm - the digital output is enabled when the
Same as VIRT ALARM 1 associated alarm status occurs.
Pulse - the measured energy is retransmitted by
Same as VIRT ALARM 1 the digital output with pulses.
Remote - the digital output can be controlled
through a command that is sent through the serial
communication port.
– 182 AL LINK: select the virtual alarm that it has
list of available to be associated.
variables
– 183 AL STATUS: ‘ND’ (normally de-energized
relay) or ‘NE’ (normally energized relay).
– 185 PULSE WEIG: selects the pulse weight
(kWh per pulse).
– 186 OUT TEST: Tests the digital output. YES
Same as DIG OUT 1 enables the test, No disables the test.
– 187 POWER TEST: sets a simulated power value
(kW) to test the energy pulse output. The
function remains active until you exit the
programming menu.

• 200 AN OUT 1: User programming of the analog

List of available outputs (0…20 mA).
variables
– 201 VARIABLES: selects the variable to be
retransmitted with the analog output.
– 202 MIN OUTPUT: sets the value that is
expressed as % of the output range (0…20 mA)
that corresponds to the minimum measured value.
– 203 MAX OUTPUT: selects the value that is
expressed as % of the output range (0…20 mA)
that corresponds to the maximum measured value.
Same as AN OUT 1
– 204 MIN INPUT: minimum value of the variable
input range, corresponds to the ‘MIN OUTPUT’
value of the analog output.
– 205 MAX INPUT: maximum value of the variable
input range corresponds to the ‘MAX OUTPUT’
• 220 METERS: reset the ENERGY METERS.
Choose among the following:
– 221 TOTAL: resets all total energy meters.
– 222 PARTIAL: resets all partial energy meters.
– 223 TOTAL +: resets the total meters of imported
energy.
– 224 TOTAL -: resets the total meters of exported
energy.
– 225 PARTIAL +: resets the partial meters of
imported energy.
– 226 PARTIAL -: resets the partial meters of
exported energy.
• 230 RESET: Resets the MAX or dmd stored values.

• 240 CLOCK:
– 241 FORMAT: UE, sets the European time
format as 24h (00:00) or sets the time format as
12h (12:00 AM/PM).
– 242 YEAR: sets the current year.
– 243 MONTH: sets the current month.
– 244 DAY: sets the current day.
– 245 HOUR: sets the current hour.
– 246 MINUTE: sets the current minute.
– 247 SECOND: sets the current second.
• 250 CHANGE PAS: this function lets you modify
the PASS value with a new value (from 0…9999).
• 260 SAVE:
– To save programming changes, press Program/
select.
– To exit the Programming mode without saving any
changes, press Exit and confirm by pressing
Save the set
parameters and come
Program/select.
SAVE
back to the measuring – If no buttons are pressed for two minutes, the unit
mode. exits Programming mode without saving changes.

Digital Filtering Operation Digital filtering smooths out the display of fluctuating values. The parameter
FILTER S defines the operating range of the filter. This operating range is
represented as a yellow band (each small square is one digit). While the
measured value (red curve in Figure 23) is within this band, the filter is active.
Once the value exceeds the operating range, the filter is deactivated and a new
band is active around the new value. The range of fluctuation (in digits) is a
good starting value for such parameters.
The parameter FILTER CO represents the filtering coefficient. The higher the
FILTER CO, the smoother the curve of the displayed values (black in
Figure 23). There is not a theoretical rule to define this parameter, it is set in
the field. One rule is to start with the value of the FILTER S coefficient and
then increase FILTER CO until the desired stability is reached.
The digital filter affects the values retransmitted both via serial communication
and analog output.
Figure 23 - Digital Filter
No filter action
Digital Fluctuation
Digital Filter Programming Examples
This section gives digital filter programming examples.
Example 1
This example describes how to stabilize the displayed value of the VL-N
variable, which fluctuates between 222V and 228V. The parameters of the
digital filter have to be programmed as follows.
FILTER S: The variable fluctuates within the mean value whose amplitude is
equal to ±0.75% of the full scale rated value of the variable itself, which is
obtained by the following calculation:
(228 - 222)/ 2= ±3V, then ±3*100/400V= ±0.75%
where 400V is the line-to-neutral rated value of a 1420-V2 unit input

The FILTER S parameter, which represents the action range of the digital
filter, is programmed to a value that must be slightly higher than the percentage
amplitude of the fluctuation, for example, 1.0%.
FILTER CO: if the new value that is measured by the instrument is within the
action range of the filter, the new displayed value is obtained by adding
algebraically the previous value to the variation divided by the filtering
coefficient. As a consequence, a value higher than this coefficient implies a
longer settling time and therefore better stability. You generally obtain the best
result by setting the filtering coefficient to a value equal to at least 10 times the
range parameter value.
In the following example, 1.0*10=10, the stability of the filtering coefficient

can be improved by increasing the filtering coefficient; the allowed values are
included within 1 and 255.
Example 2
This example describes how to stabilize the value of the displayed System Real
Power (W), which fluctuates 300...320 kW. In this example, the load is
connected to the instrument with a 300/5 A CT and a direct measure of the
voltage.
The parameters of the digital filter must be programmed as follows.
FILTER S: the variable fluctuates within the mean value whose amplitude is
equal to ±2.78% of the full scale rated value of this variable. This value is
obtained by the following calculation:
(320 - 300)/ 2= ±10 kW,
then ±10*100/360 kW= ±2.78%,
where 360 kW is the rated value of the System Real Power of a 1420-V2
unit input, at the CT and VT ratios and obtained with the following
formula:
VLN * VT * IN * CT * 3
Where:
VLN = rated input voltage (400V for the V1 input)
VT= primary/secondary ratio of the voltage transformer being used
IN = rated current (5 A)
CT = primary/secondary ratio of the voltage transformer being used (in

this example 400*1*5*60*3=360 kW).
The FILTER S parameter, which represents the digital filtering coefficient

action range, is programmed to a value that must be slightly higher than the
percentage of the fluctuation: for example 3.0%.

FILTER CO: if the new value that is acquired by the unit is within the filtering
action range, the new displayed value is obtained by adding algebraically the
previous value to the variation divided by the filtering coefficient. As a
consequence, a value higher than this coefficient implies a higher settling time
and therefore better stability. Therefore, the best result is obtained by setting
the filtering coefficient to a value equal to at least 10 times the value of the
range parameters. In the example, 3.0*10=30. To improve the stability, you can
increase the filtering coefficient; the admitted values are included within
1 and 255.
Example 3
It is necessary to stabilize the value of the displayed variable A L1

(phase current 1), which fluctuates in the range 470 A and 486 A.
To be able to manage the alarm function and activation and deactivation of the
relay, this value is not to be subject to continuous fluctuations. In this example,
we have considered using a 500/5 A CT. Program the parameters of the digital
filter as follows:
FILTER S: the variable fluctuates within the mean value whose amplitude is
equal to ±1.60% of the full scale rated value of this variable (obtained with the
calculation:
(486 - 470)/ 2= ±8 A, then ±8*100/500 A= ±1.60%
where 500 A is the value referred to the primary of the transformer being
used).
The FILTER S parameter, which represents the action range of the digital
filter, is programmed to a value slightly higher than the percentage amplitude
of the fluctuation, for example 2.0%.
FILTER CO: if the new value that is acquired by the instrument is within the
filtering action range, the new displayed value is calculated algebraically adding
to the previous value the variation divided by the filtering coefficient. As a
consequence, a higher value of this coefficient implies a higher settling time
and therefore better stability. Therefore, the best result is obtained setting the
filtering coefficient at a value equal to at least 10 times the value of the range
parameter. In the example, 2.0*10=20. To improve the stability, you can
increase the filtering coefficient; the admitted values are within 1 and 255.

Analog Output Configuration These examples apply to units with catalog numbers 1420-V1A and 1420-
V2A.
Examples
Example 1: Power value retransmission with a 0…20 mA analog output.
This example describes how to retransmit measured power up to

100 kW with a 4…20 mA signal. Program the unit as follows:
• VARIABLE: WΣ (system real power)
• MIN OUT: 20.0% means 4 mA. The calculation that is used is the
following:
(100*minimum output) / full scale output =100*4 mA/ 20 mA=20%
• MAX OUT: 100.0% means 20 mA. The calculation is the following:
(100*maximum output)/full scale output = 100*20 mA/20 mA= 100
• MIN INPUT: 0.0 k; the multiplier k, M, G can be selected on the unit
according to the chosen VT and CT values
• MAX INPUT: 100.0 k; the k, M, G multipliers can be selected on the
unit according to the selected VT and CT values
Example 2: Retransmission of the power factor (PF) value with the

0…20 mA analog output.
In this example, the unit is configured to retransmit the whole range of the
allowed values for the PF with a signal from 0…20 mA. The value of the PF
variable can vary between C0.001 and L0.000 (for each phase); these values,
when retransmitted, correspond to 0 mA and 20 mA. When the PF value is
equal to 1, the analog output value corresponds to the middle of the scale,
which is 10 mA. Program the instrument as follows:
• VARIABLE: PF L1 (or L2 or L3 or PFΣ)
• MIN OUT: 0.0%
• MAX OUT: 100.0%
• MIN INPUT: C0.001 (the C symbol shows a CAPACITIVE value)
• MAX INPUT: L0.001 (the L symbol shows an INDUCTIVE value).
L0.001 has been chosen as minimum value to be set to avoid undesirable
rapid changes of the outputs

Alarm Configuration These examples apply to units with catalog numbers 1420-V1P and 1420-V2P.
Example This example describes an alarm when a measured real power value exceeds a
programmed threshold. For example, when 300 kW are exceeded, the alarm
occurs and the load that is controlled by the relay output is disconnected.
IMPORTANT The PowerMonitor 500 unit is not intended to be applied as a protective

device.
An ‘UP’ alarm is selected. The recommended programming is the following:

• ENABLE: YES
• VARIABLES: W system (W·)
• SET POINT 1: 300 kW
• SET POINT 2: 295 kW
• ON DELAY: set the desired number of seconds, for example 5 seconds
300 kW
295 kW
To program a ‘DOWN’ alarm, configure SET POINT 1 to be a lower value

than SET POINT 2.

Notes:

Chapter 4
Communication
EtherNet/IP Communication EtherNet/IP communication is supported in PowerMonitor™ 500 units that

are ordered with optional Ethernet communication. Communication
parameters in the power monitor must be configured. See Unit Configuration
on page 25. The Ethernet communication port supports 100 or 10 Mbps data
rate, half-duplex, or full-duplex.
TIP The Ethernet hardware address (MAC ID) is printed on the unit label.
The PowerMonitor 500 unit provides nine Assembly Instances that contain
real-time, maximum, demand, energy, and status data that can be read by a
client by using implicit messaging (Class 1) or Explicit Messaging (Class 3 or
UCMM).
Appendix A lists the Assembly Instances, sizes, data types, and other details.
The power monitor returns EtherNet/IP data as little-endian, the same byte
order that is used in the Logix family of programmable controllers.
Figure 24 - Byte Order Example

Word
Low Byte (LSB) High Byte (MSB)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MSb (Most Significant Bit) (Least Significant Bit) LSb
The power monitor supports the following communication commands:

• CIP Generic Assembly Object (Class 04), Get_Attribute_Single
(Service Code 0x0E) for Attribute 3 (data)
• CIP Generic Assembly Object (Class 04), Get_Attribute_Single
(Service Code 0x0E) for Attribute 4 (size in bytes)
IMPORTANT The power monitor does not support configuration or commands on

EtherNet/IP network. To write the configuration of command data, refer to
the section on Modbus Communication on page 45.
See Appendix C for additional information on the EtherNet/IP

communication implementation in the PowerMonitor 500 unit.

Chapter 4 Communication
Electronic Data Sheet (EDS)
The EDS file is used to convey device configuration data that is provided by the
manufacturer. You can obtain EDS files for the PowerMonitor 500 unit by
downloading the file from the following website:
http://compatibility.rockwellautomation.com/Pages/MultiProductDownload.aspx
You can install EDS files on your computer by using the EDS Hardware
Installation Tool that comes with RSLinx® Classic software,
RSNetWorx™ for EtherNet/IP software, or other tools.
Explicit Messaging - Message Setup with CIP Generic

The following example shows how to configure your message instruction to
read from a data table in the power monitor by using a CIP Generic message
type for the Studio 5000 Logix Designer® application. This setup applies to
ControlLogix® and CompactLogix™ programmable logic controllers. The CIP
Generic message type does not support single element reads or writes. In this
example, we read the Real-time Metering Values (Voltage and Current) data
table from the power monitor.

Communication Chapter 4
We assume that you are familiar with basic message programming in a Logix
controller. Once you configure the logic, message tag, destination tag, and
message instruction, follow these steps to configure the message. This example
uses a CompactLogix™ controller, revision 20.
1. Choose the appropriate parameters in the Message Configuration

window.
Parameter Choice
Message Type Choose message type CIP Generic.
Service Type Read: Select service type Get Attribute Single (E hex)
Instance See Appendix A for the CIP Instance of the data table to read. In this example, the power
monitor Real-time Metering Values (Voltage and Current) data table is instance 101 (decimal).
Class 4 hex
Attribute 3 hex
Destination Get Attribute Single - This element is the first element of the controller tag that stores the data
being read. The tag is an array of the applicable data type the same length as the Assembly
Instance; in this example, 12 REAL elements.
Source Element Not applicable to a Read
Source Length Not applicable to a Read

2. Click the Communication tab and enter the path and method.
3. Click OK to complete message setup.
Path Method
<Ethernet Module, Port (always 2 for Ethernet), Power Monitor IP Address> CIP
Implicit Messaging - Generic Ethernet Module Input Data

Connection
The PowerMonitor 500 unit with EtherNet/IP communication supports Class

1 connections to its nine Assembly Instances. To configure a Class 1
connection to a selected Assembly Instance with a Logix controller, follow
these steps.
1. Open the controller program offline in the Logix Designer application

(or online in Program mode if you are using a ControlLogix® controller).
2. In the I/O configuration tree, right-click the Ethernet communication
module (for example, 1756-EN2T), and choose New Module.
3. From the Communication pull-down menu, choose ETHERNET-
MODULE Generic Ethernet Module.

4. Enter the setup parameters as listed in this dialog box and explained in
Table 7.
Table 7 - Module Properties Setup Parameters

Item Choices
General Tab
Name Required; must be IEC 1131-3 compliant
Description Optional
Comm Format Depends on selected Assembly Instance(1)
Address/Host Name IP Address IP address of target PowerMonitor 500 unit
Host Name Not applicable
Connection Parameters Assembly Instance Size Comm Format Data Table Description
Input (select one) 100 20 Input Data - SINT Product Information
101 12 Input Data - REAL Real-time Voltage and Current
102 18 Input Data - REAL Real-time Power, PF, Frequency
103 12 Input Data - REAL Max Voltage and Current
104 17 Input Data - REAL Max Power, PF, Frequency
105 12 Input Data - REAL Dmd Voltage and Current
106 17 Input Data - REAL Dmd Power, PF, Frequency
107 18 Input Data - REAL Energy Meters
108 2 Input Data - INT Alarm and Output Status
Output 98 N/A Inst. 98 used for Input Only connection
99 N/A Inst. 99 used for Listen Only connection(1)
Configuration 3 0 Instance 3 is a placeholder
only
Connection Tab
RPI 100 ms or greater
Inhibit Module Optional - unchecked by default
Major Fault Optional - unchecked by default
Unicast Connection Optional - checked by default
(1) Use the Listen Only connection only when an Input Only connection exists with another controller.

5. When finished, click OK to save the new module.

The module updates its input tag <Name>.I.Data at the Requested
Packet Interval (RPI).
You can use additional programming to show the data in another way.
Instances 101…107 show data in the REAL, or floating point, format.
However, Instance 100 combines ASCII characters with numeric byte (SINT)
values.
This program displays the contents of Instance 100 in a more human-readable

fashion:
• The XIC instruction on tag ‘bool_Convert_i100’ enables the
conversion.
• The first CPS instruction copies the first 6 bytes of the module input
data tag.
• The MOV instruction sets the serial number string length to 13.
• The last CPS instruction copies the serial number from the module
input data tag that starts at element (byte) 6.

The destinations of the CPS instructions are in a tag with a user-defined data
type.
The destination tag shows the data in this way.
Modbus Communication For a complete description of the MODBUS protocol refer to the following
documents that can be downloaded from http://www.modbus.org:
• Modbus_Application_Protocol_ V1_1a
• Modbus_Messaging_Implementation_Guide_V1_0a
Modbus Functions Supported

Modbus RTU is supported in PowerMonitor 500 units that are ordered with
optional RS-485/RS-232 communication. In addition, Modbus TCP/IP is
supported in units that are ordered with optional Ethernet communication.
Communication parameters in the power monitor must be configured. See the
Unit Configuration section of this manual.
IMPORTANT We recommend that you use Modbus TCP/IP to configure or write to the
PowerMonitor 500 unit and that you use Ethernet/IP to read the
PowerMonitor 500 unit.

The PowerMonitor 500 unit supports the following Modbus functions:

• 0x03 - Read n Holding Registers
• 0x04 - Read n Input Register
• 0x06 - Write one Holding Register
• 0x10 - Write multiple registers
• 0x08 - Diagnostic (with subfunction code 0x00)
• 0x42 - Read n Special Registers (vendor specific)
• Broadcast mode (write command on address 00h)
In this section, Modbus addresses are indicated in two ways. The ‘Modbus
address’ is expressed as the 6-digit input register address (example: 300123),
used with Modbus function code 0x04. The ‘Physical address’ is the
hexadecimal representation of the word address that is included in the
communication frame.
Modbus function 0x04 can be used with the Modbus address by substituting a
4 for the first digit (example: 400123). With that distinction, functions 0x03
and 0x04 return the same data.
To avoid errors due to signal reflections or line coupling, a termination resistor

must be connected at the RS-485 ports of the master station and of the furthest
power monitor from the master station. In the PowerMonitor 500, you can
implement a jumper between (B+) and (T) to apply the required termination
resistance between (A-) and (B+) internally. Termination on both ends is
necessary even in case of point-to-point connection, with short distances.
The GND connection is optional if a shielded cable is used. For connections

longer than 1000 m (3280 ft), a line amplifier is necessary.
Data Types Supported

Format Description Bits Range
INT Integer 16 -32768…32767
UNIT Unsigned Integer 16 0… 65535
DINT Double integer 32 -231… 231-1
UDINT Unsigned Double Integer 32 0…232-1
ULINT Unsigned long Integer 64 0…264-1
REAL Single-precision Floating Point 32 -(1+[1-2-23])x2127…2128
The IEEE754 representation of a 32-bit Floating Point number as an Integer is

defined as follows.
Bits
31 30…23 22…0
Sign Exponent Mantissa
Value= (-1)sign*2(Exponent-127)*1.Mantissa

Modbus Register Format
Modbus registers are 16-bit words that are organized as shown in the following
diagram.
Holding Register (word)
High Byte (MSB) Low Byte (LSB)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
MSb (Most Significant Bit) (Least Significant Bit) LSb
32-bit and 64-bit Data types that are presented as arrays of single registers in
LSW (least significant word) to MSW (most significant word) order.

Notes:

Appendix A
PowerMonitor 500 Unit Data Tables
Summary of Data Tables The Data Table Summary Index table summarizes all data tables available and
their general attributes.
Table 8 - Data Table Summary Index

Name of Data Table Read Write Modbus Starting CIP Assy. Instance ID No. of Elements See Page
Address (decimal)
Product Information X 300001(1) 100 10 51
Real-time Metering Values (voltage and current) X 300081 101 12 52
Real-time Metering Values (power, PF, X 300105 102 18 53
frequency)
Maximum Metering Values (voltage and current) X 300337 103 12 54
Maximum Metering Values (power, PF, X 300361 104 17 55
frequency)
DMD Metering Values (voltage and current) X 300849 105 12 56
DMD Metering Values (power, PF, frequency) X 300873 106 17 57
Total and Partial Energy Meters - EtherNet/IP X 301281 107 18 58
Data Table
Configuration - Base Unit: Read and Write X X 304097 - 79 59
Configuration - Alarms X X Varies - 16 60
Configuration - RS-485/RS-232 Communication X X 304356 - 17 60
Configuration - Analog Outputs: Read and Write X X 304609 - 32 61
Analog Output Configuration Parameters X X Varies - 16 61
Configuration - Digital Relay Outputs: Read and X X 304865 - 12 62
Write
Commands: Write-only X 312369 - 45 63
Alarm and Output Status X 316385 108 2 65
(1) To obtain the physical address, subtract 300001 from the Modbus address, and convert the result to hexadecimal. Example: Physical address 0x000B corresponds to Modbus address
300012.

Appendix A PowerMonitor 500 Unit Data Tables
Geometric Representation of Power and power factor values are signed values in accordance with EN 62053
and as indicated in the diagram. Inductive or lagging power factor (Quadrant I
Power and Power Factor and III) is indicated by a positive power factor value. Capacitive or leading
power factor (Quadrant II and IV) is indicated by a negative power factor
value. The PowerMonitor™ 500 unit indicates the quadrant by using +/- L or
+/- C as shown in Figure 25.
Figure 25 - Power and Power Factor Diagram

-W +W - W = Exported real power
PF < 0, ‘-C’ PF > 0, ‘L’
+ W = Imported real power
+ VAR = Imported reactive

+VAR
power
Q
P - VAR = Exported reactive
power
-VAR
PF > 0, ‘-L’ PF < 0, ‘C’

PowerMonitor 500 Unit Data Tables Appendix A
Data Tables These tables detail each specific data table and its associated elements, such as
address, length, description, and format.
IMPORTANT In the data tables, the  symbol is used to indicate 3-phase or system
values. The context determines whether the symbol indicates average (for
example, voltage) or total (for example, power) values.
Product Information
Table 9 - Table Properties
CIP Assembly Instance 100
No. of Elements 10
Length in Words 10
Data Type UINT
Data Access Read Only
Table 10 - Product Information Data Table

Element Modbus Length Description / Units Data Notes
Address (words) Format
1 300001 1 Base firmware revision UINT MSB: ASCII code for model (A = V2, B = V1)
LSB: numeric number for revision
2 300002 1 EtherNet/IP module firmware revision UINT MSB: ASCII code for model
3 300003 1 Analog output module firmware revision (if exists) UINT MSB: ASCII code for model
4 300033 1 Letter 1 (from SX) UINT MSB: ASCII code
Letter 2 (from SX) LSB: ASCII code

Real-time Metering Values (voltage and current)

No. of Elements 12
Length in Words 24
Data Type REAL
Table 12 - Real-time Metering Values (voltage and current) Data Table

Element Modbus Length Description / Units Data Format Notes
Address (words)
0 300081 2 V L1-N REAL
1 300083 2 V L2-N REAL
2 300085 2 V L3-N REAL
3 300087 2 V L-N  REAL
4 300089 2 V L1-L2 REAL
5 300091 2 V L2-L3 REAL
6 300093 2 V L3-L1 REAL
7 300095 2 V L-L  REAL
8 300097 2 A L1 REAL
9 300099 2 A L2 REAL
10 300101 2 A L3 REAL
11 300103 2 AN REAL Calculated by instrument base

Real-time Metering Values (power, PF, frequency)

No. of Elements 18
Length in Words 36
Data Type REAL
Table 14 - Real-time Metering Values (power, PF, frequency) Data Table

Address (words)
0 300105 2 W L1 REAL
1 300107 2 W L2 REAL
2 300109 2 W L3 REAL
3 300111 2 W REAL
4 300113 2 VA L1 REAL
5 300115 2 VA L2 REAL
6 300117 2 VA L3 REAL
7 300119 2 VA  REAL
8 300121 2 VAR L1 REAL
9 300123 2 VAR L2 REAL
10 300125 2 VAR L3 REAL
11 300127 2 VAR  REAL
12 300129 2 PF L1 REAL Negative values correspond to lead (C), positive values
correspond to lag (L)
13 300131 2 PF L2 REAL
14 300133 2 PF L3 REAL
15 300135 2 PF  REAL
16 300137 2 Hz REAL
17 300139 2 Voltage phase sequence REAL 1 = L1-L2-L3 voltage rotation
-1 = Not L1-L2-L3 voltage rotation

Maximum Metering Values (voltage and current)

No. of Elements 12
Length in Words 24
Data Type REAL
Table 16 - Maximum Metering Values (voltage and current) Data Table

Address (words)
0 300337 2 Max V L1-N REAL
1 300339 2 Max V L2-N REAL
2 300341 2 Max V L3-N REAL
3 300343 2 Max V L-N  REAL
4 300345 2 Max V L1-L2 REAL
5 300347 2 Max V L2-L3 REAL
6 300349 2 Max V L3-L1 REAL
7 300351 2 Max V L-L  REAL
8 300353 2 Max A L1 REAL
9 300355 2 Max A L2 REAL
10 300357 2 Max A L3 REAL
11 300359 2 Max A N REAL

Maximum Metering Values (power, PF, frequency)

No. of Elements 17
Length in Words 34
Data Type REAL
Table 18 - Maximum Metering Values (power, PF, frequency) Data Table

Address (words)
0 300361 2 Max W L1 REAL
1 300363 2 Max W L2 REAL
2 300365 2 Max W L3 REAL
3 300367 2 Max W  3 REAL
4 300369 2 Max VA L1 REAL
7 300375 2 Max VA  REAL
8 300377 2 Max VAR L1 REAL Negative values correspond to lead (C), positive values
9 300379 2 Max VAR L2 REAL
10 300381 2 Max VAR L3 REAL
11 300383 2 Max VAR  REAL
12 300385 2 Max PF L1 REAL The Max PF displayed corresponds to the PF value with the
largest phase angle.
13 300387 2 Max PF L2 REAL
14 300389 2 Max PF L3 REAL
15 300391 2 Max PF  REAL
16 300393 2 Max Hz REAL

DMD Metering Values (voltage and current)

No. of Elements 12
Length in Words 24
Data Type REAL
Table 20 - DMD Metering Values (voltage and current) Data Table

Address (words)
0 300849 2 DMD V L1-N REAL
1 300851 2 DMD V L2-N REAL
2 300853 2 DMD V L3-N REAL
3 300855 2 DMD V L-N  REAL
4 300857 2 DMD V L1-L2 REAL
5 300859 2 DMD V L2-L3 REAL
6 300861 2 DMD V L3-L1 REAL
7 300863 2 DMD V L-L  REAL
8 300865 2 DMD A L1 REAL
9 300867 2 DMD A L2 REAL
10 300869 2 DMD A L3 REAL
11 300871 2 DMD A N REAL

DMD Metering Values (power, PF, frequency)

No. of Elements 17
Length in Words 34
Data Type REAL
Table 22 - DMD Metering Values (power, PF, frequency) Data Table

Address (words)
0 300873 2 DMD W L1 REAL
1 300875 2 DMD W L2 REAL
2 300877 2 DMD W L3 REAL
3 300879 2 DMD W  REAL
4 300881 2 DMD VA L1 REAL
7 300887 2 DMD VA  REAL
8 300889 2 DMD VAR L1 REAL Negative values correspond to lead (C), positive values
9 300891 2 DMD VAR L2 REAL
10 300893 2 DMD VAR L3 REAL
11 300895 2 DMD VAR  REAL
12 300897 2 DMD PF L1 REAL
13 300899 2 DMD PF L2 REAL
14 300901 2 DMD PF L3 REAL
15 300903 2 DMD PF  REAL
16 300905 2 DMD Hz REAL

Total and Partial Energy Meters - EtherNet/IP Data Table

No. of Elements 18
Length in Words 36
Data Type REAL
Table 24 - Total and Partial Energy Meters - EtherNet/IP Data Table

Element Length Description / Units Data Format Notes
(words)
0 2 Total kWh+ REAL Range 0.0 … 999,999.999
1 2 Total GWh+ REAL Range 0 … 9,999,999
2 2 Total kVARh+ REAL Range 0.0 … 999,999.999
3 2 Total GVARh+ REAL Range 0 … 9,999,999
4 2 Total kWh- REAL Range 0.0 … 999,999.999
5 2 Total GWh- REAL Range 0 … 9,999,999
6 2 Total kVARh- REAL Range 0.0 … 999,999.999
7 2 Total GVARh- REAL Range 0 … 9,999,999
8 2 Partial kWh+ REAL Range 0.0 … 999,999.999
9 2 Partial GWh+ REAL Range 0 … 9,999,999
10 2 Partial kVARh+ REAL Range 0.0 … 999,999.999
11 2 Partial GVARh+ REAL Range 0 … 9,999,999
12 2 Partial kWh- REAL Range 0.0 … 999,999.999
13 2 Partial GWh- REAL Range 0 … 9,999,999
14 2 Partial kVARh- REAL Range 0.0 … 999,999.999
15 2 Partial GVARh- REAL Range 0 … 9,999,999
16 2 Hours counter REAL
17 2 Minutes counter REAL Range 0 … 59

Table 25 - Energy Metering Values Modbus - Read-only

Modbus Length Description / Units Data Format Notes
Address (words)
301281 4 Total kWh+ ULINT Values in Wh or varh
301285 4 Total kVARh+ ULINT
301289 4 Total kWh- ULINT
301293 4 Total kVARh- ULINT
301297 4 Partial kWh+ ULINT
301301 4 Partial kVARh+ ULINT
301305 4 Partial kWh- ULINT
301309 4 Partial kVARh- ULINT
301313 4 Hours counter ULINT Hours value: Integer part got from the division of the counter by
100-Minutes value: rest of the previous computation (decimal part)
Table 26 - Configuration - Base Unit: Read and Write

Address (words)
304097 1 Password UINT Minimum valid value: 0d Maximum valid value: 9999d
304098 1 Electrical system selection UINT Value =0: 1P (1-phase 2-wire) Value =1: 2P (2-phase 3-wire)
Value=2: 3P (3-phase 3-wire) Value=3: 3P2 (3-phase 2-wire) one
current and 1-phase (L1) to neutral voltage measurement)
Value=4: 3P1 (3-phase 4-wire one current and 3-phase to neutral
voltage measurements) Value=5: 3PN (default =3PN)
304099 1 Reserved UINT
304101 1 Backlight mode UINT The timing backlight is programmable from 0…255 minutes
(0 = always ON)
304107 1 DMD - Calculation UINT Selection of the DMD calculation mode Value=0: Fixed Value=1:
Slide - only for W and VA
304108 1 DMD - Time interval UINT Value=0: 1 min Value=1: 5 min Value=2: 10 min Value=3: 15 min
Value=4: 20 min Value=5: 30 min Value=6: 60 min
304110 1 DMD - Synchronization UINT Synchronization selection mode Value=0: OFF Value=1: Clock
304121 2 CT - Current transformer ratio REAL 1.0…9999.0
304123 2 VT(PT) - Voltage transformer ratio REAL 1.0…9999.0
304127 2 Filter Span parameter REAL Value min = 0.0
Value max = 100.0 (Disabled = 0.0)
304129 2 Filter Coefficient REAL Value min = 1.0
Value max = 256.0
304177 16 Virtual Alarm AL1 (LED 1) Customized See the Table 27
304193 16 Virtual Alarm AL2 (LED 2) Base Alarm data structure
304209 16 Virtual Alarm AL3 (LED 3)
304225 16 Virtual Alarm AL4 (LED 4)

Table 27 - Configuration - Alarms

Address (words)
Block address 1 Alarm N - Enabling UINT Value=1: alarm N enabled Value=0: alarm N disabled All other
+0 values are considered as value=0
Block address 1 Alarm N - Variable type to be linked UINT See the Connected Variable List (Table 45)
+1 to
Block address 1 Alarm N - Delay ON activation (s) UINT Value min=0 Value max=3600 If the set value exceeds the allowed
+2 range, the instrument automatically sets the value to 0
Block address 2 Alarm N – Set point 1 REAL Value min = -9999M Value max = 9999M If the set value exceeds
+3 the allowed range, the instrument automatically sets the value to
0.000
Block address 2 Alarm N – Set point 2 REAL Value min = -9999M Value max = 9999M If the set value exceeds
+5 the allowed range, the instrument automatically sets the value to
0.000
Block address 9 Reserved
+7
Table 28 - Configuration - RS-485/RS-232 Communication

Address (words)
304356 1 Clock format UINT 0=24h/12h 1=AM-PM
304357 1 Clock daylight-saving UINT Value=0: NO Value=1: YES
304358 1 Clock calendar: Year (1) UINT 2009…2099
304359 1 Clock calendar: Month (1) UINT 1…12
304360 1 Clock calendar: Day (1) UINT 1…31
304361 1 Clock: Hour(1) UINT 0…23
304362 1 Clock: Minutes (1) UINT 0…59
304363 1 Clock: Seconds (1) UINT 0…59
304364 1 Daylight-saving: month in which to UINT 1…12
increase the hour (+1H)
304365 1 Daylight-saving: Sunday in which to UINT 0…4 (0= last Sunday of the month)
304366 1 Daylight-saving: hour in which to UINT 0…23 (24h format only)
304367 1 Daylight-saving: month in which to UINT 1…12
decrease the hour (-1H)
304368 1 Daylight-saving: Sunday in which to UINT 0…4 (0= last Sunday of the month)
304369 1 Daylight-saving: hour in which to UINT 0…23 (24h format only)
304401 1 RS-485 instrument address UINT Value min = 1 Value max = 247 If the set value exceeds the allowed
selection(2) range, the instrument automatically sets the value to 1
304402 1 RS-485 baud rate selection(2) UINT Value=0: 9600 Value=1: 19200 Value=2: 38400 Value=3: 115200
All other values are considered as value=0
304403 1 RS-485 parity selection (2) UINT Value=0: No parity Value=1: Odd parity Value=2: Even parity All
other values are considered as value=0
(1) The values are updated only after sending the ‘update clock’ command.
(2) The values are updated only after sending the ‘update serial communication setting’ command or switching off and on the instrument.

Table 29 - Configuration - Analog Outputs: Read and Write

Address (words)
304609 16 Analog output A0: parameters CUSTOM See Table 28
configuration
304625 16 Analog output A1: parameters CUSTOM
configuration
Table 30 - Analog Output Configuration Parameters

Address (words)
Block 1 Type of the variable that is linked to UINT
address +0 the N analog output
Block 2 Minimum electric value of the N REAL Value min = 0
address +1 analog output Value max = 9,999,000
Block 2 Maximum electric value of the N REAL
address +3 analog output
Block 2 Minimum output value of the N REAL Value min = 0.0
address +5 analog output Value max = 100.0
Block 2 Maximum output value of the N REAL
address +7 analog output
Block 7 Reserved
address +9

Table 31 - Configuration - Digital Relay Outputs: Read and Write

Address (words)
304865 1 Digital output channel 1: enabling UINT 0=Remote
1=Alarm
2= Pulse
304866 1 Digital output channel 1: output UINT 0=NO
working mode 1=NC (only if selected ‘Alarm’ type)
304867 1 Digital output channel 1: linked UINT 0=AL1
alarm 1=AL2
2=AL3
3=AL4 (only if selected ‘Alarm’ type)
304868 1 Channel 1: linked counter-variable UINT 0=Total kWh+
1=Total kVARh+
2=Total kWh-
3=Total kVARh-
4=Partial kWh+
5= Partial kVARh+
6= Partial kWh-
7= Partial kVARh-
304869 2 Digital output channel 1: pulse REAL Pulse weight (kWh/pulse or kVARh/pulse)
Value min = 0.001
Value max = 9999.9
304871 1 Digital output channel 2: enabling UINT 0=Remote
1=Alarm
2= Pulse
304872 1 Digital output channel 2: output UINT 0=NO
working mode 1=NC (only if selected ‘Alarm’ type)
304873 1 Digital output channel 2: linked UINT 0=AL1
alarm 1=AL2
2=AL3
3=AL4 (only if selected ‘Alarm’ type)
304874 1 Channel 2: linked counter-variable UINT 0=Total kWh+
1=Total kVARh+
2=Total kWh-
3=Total kVARh-
4=Partial kWh+
5= Partial kVARh+
6= Partial kWh-
7= Partial kVARh-
304875 2 Digital output channel 2: pulse REAL Pulse weight (kWh/pulse or kVARh/pulse)
Value min = 0.001
Value max = 9999.0

Table 32 - Commands: Write-only

Address (words)
312369 1 Get clock values UINT Value=1 - command executed; Value≠1 - no effect
312370 1 Set clock values UINT Value=1 - date and time set
312374 1 Enable optional pulse (digital) outputs UINT Value=1 - module enabled; Value=0 - module disabled
312376 1 Enable optional serial communication UINT Value=1 - module enabled; Value=0 - module disabled
312546 1 Reset all pulse (digital) outputs (digital UINT Value=1 - command executed; Value≠1 - no effect
output 1 or 2)
312547 1 Set pulse (digital) output 1 UINT Value=0 - reset output; Value=1 - set output; Other values - no
effect
312548 1 Set pulse (digital) output 2 UINT Value=0 - reset output; Value=1 - set output; Other values - no
effect
312549 1 Set all pulse (digital) outputs (digital UINT Value=1 - command executed; Value≠1 - no effect
output 1 or 2)
312802 1 Reset V L1-N UINT 16 Bit0 = 1: Reset Max Value
Bit1 = 1: Reset DMD value
312803 1 Reset V L2-N UINT 16
Bits 2 … 15: Reserved
312804 1 Reset V L3-N UINT 16
312805 1 Reset V L-N  UINT 16
312806 1 Reset V L1-L2 UINT 16
312809 1 Reset V L-L  UINT 16
312810 1 Reset A L1 UINT 16
312813 1 Reset A N UINT 16

Table 32 - Commands: Write-only

Address (words)
312814 1 Reset W L1 UINT 16 Bit0 = 1: Reset Max Value
Bit1 = 1: Reset DMD value
312815 1 Reset W L2 UINT 16
Bits 2 … 15: Reserved
312816 1 Reset W L3 UINT 16
312817 1 Reset W  UINT 16
312818 1 Reset VA L1 UINT 16
312821 1 Reset VA  UINT 16
312822 1 Reset VAR L1 UINT 16
312825 1 Reset VAR  UINT 16
312826 1 Reset PF L1 UINT 16
312829 1 Reset PF  UINT 16
312830 1 Reset Hz UINT 16
313569 1 Reset Total kWh+ UINT Value=1 - command executed
313570 1 Reset Total kVARh+ UINT Value=1 - command executed
313571 1 Reset Total kWh- UINT Value=1 - command executed
313572 1 Reset Total kVARh- UINT Value=1 - command executed
313573 1 Reset Partial kWh+ UINT 16 Value=1 - command executed
313574 1 Reset Partial kVARh+ UINT 16 Value=1 - command executed
313575 1 Reset Partial kWh- UINT 16 Value=1 - command executed
313576 1 Reset Partial kVARh- UINT 16 Value=1 - command executed

Alarm and Output Status

No. of Elements 2
Length in Words 2
Data Type INT
Table 34 - Alarm and Output Status: read-only Mode Data Table

Address (words)
0 316385 1 Virtual alarm UINT Bit value: 0 = OFF
Bit value: 1 = ON
Bit position:
0: Virtual alarm 1
1: Virtual alarm 2
2: Virtual alarm 3
3: Virtual alarm 4
1 316386 1 Output (port) UINT Bit value
0 = OFF Bit value
1 = ON (Important: only if the port is not linked to the counter)
Bit position (LSB concept): 0: Port1
1: Port2
2 (see 316387 1 HW modules configuration UINT Bit value:
Important) 0 = module not present
1 = module present
Bit position
0: Relay output
1: Reserved
2: RS-485/RS-232 port
3: Ethernet Modbus
4: Reserved
5: Analog output
6: Reserved
7: Reserved
8: EtherNet/IP
9…15: Reserved
IMPORTANT A Get_Attribute_Single command returns only elements 0 and 1 of this

table. The information in element 2 is accessible in the Identity Object, Class
0x01.

Notes:

Appendix B
Technical Specifications
Table 35 - Input Specifications

Attribute Value
Rated inputs System type: 1, 2, or 3-phase
Current type Galvanic insulation with built-in CTs
Current range (by CT) 5 A nom (6 A max)
Voltage (by direct connection or VT/PT) V1: 120/208V LL; V2: 400/600V LL
Accuracy (Display and RS-485) Current, nom (Inom): 5 A
(at 25 °C ±5 °C, R.H. ≤ 60%, 48…62 Hz) Voltage, nom (Vnom): V1: 120V AC LN, 208V AC LL; V2: 400V AC LN, 600V AC LL
V1 model Inom: 5 A, Imax: 6A
Line-neutral RMS: 40…144V AC
Line-Line RMS: 70…250V AC
V2 model Inom: 5 A, Imax: 6 A
Line-neutral RMS: 160…480V AC
Line-line RMS: 277…830V AC
Current all models From 0.01…0.25 A: ±(1.0% of reading (RDG) + 2 digits
From 0.25…6 A: ±(0.5% RDG +2 digits)
Line-neutral voltage In the range Vnom: ±(0.5% RDG +1 digit)
Line-line voltage In the range Vnom: ±(1.0% RDG +1 digit)
Frequency ±0.1 Hz (45…65 Hz)
Real and apparent power From 0.05… 0.25 A, PF 1: ±(2% RDG +1 digit)
From 0.25…6A, PF 0.5L, PF1, PF 0.8C: ±(1.0% RDG+1 digit)
Power factor (PF) ±[0.001+0.5% (1.000 - ‘PF RDG’)]
Reactive power From 0.5… 6 A, sinφ 0.5L/C: ±(2.0% RDG +1 digit)
From 0.25… 0.5 A, sinφ 0.5L/C: ±(2.5% RDG +1 digit)
From 0.25…6 A, sinφ 1.0: ±(2.0% RDG+1 digit)
From 0.1… 0.25 A, sinφ 1: ±(2.5% RDG+1 digit)
TIP: sinφ = VAR/VA
Real energy Class 1 according to EN62053-21, ANSI C12.1 Class B according to EN50470-3
Reactive energy Class 2 according to EN62053-23, ANSI C12.1
Start up current 5 mA
Energy additional errors According to EN62053-21 ANSI C12.1, Influence quantities Class B according to EN50470-3, EN62053-23
Temperature drift ≤ 200 ppm/°C
Sampling rate 3840 samples/second at 60 Hz, 3200 samples/second at 50 Hz
Measurements See List of Connectable Variables on page 74
Method True RMS measurements of distorted wave forms
Coupling type With CTs
Crest factor ≤3 (15 A max peak)

Appendix B Technical Specifications
Table 35 - Input Specifications

Attribute Value
Current overloads
Continuous 6 A, at 50/60 Hz
For 500 ms 120 A, at 50/60 Hz
Voltage overloads
Continuous 1.2 × Vnom (where Vnom is the nominal voltage of the module)
For 500 ms 2 × Vnom (where Vnom is the nominal voltage of the module)
Input impedance
400VL-L (V2) > 1.6 MΩ
208VL-L (V1) > 1.6 MΩ
5(6)A < 0.2VA
Frequency 40…440 Hz
Table 36 - Pulse (digital) Output Specifications (P option)

Attribute Value
Physical outputs 2
Purpose For either alarm output or digital output
Type Relay, SPDT type:
• AC 1-5 A at 250V AC
• AC 15-1 A at 250V AC
• DC 12-5 A at 24V DC
• DC 13-1.5 A at 24V DC
Configuration Use the front keypad
Function The outputs can work as alarm outputs but also as digital outputs, communication controlled outputs, or in any other
combination
Alarms Up alarm and down alarm that is linked to the virtual alarms, for other details, see Virtual alarms on page 72
Response time, min ≤200 ms, filters excluded. Set-point on-time delay: ‘0 s’
Pulse
Signal retransmission Total: +kWh, -kWh, +kVARh, -kVARh. Partial: +kWh, -kWh, +kVARh, -kVARh
Pulse type The listed variables can be connected to any output
Pulse duration Programmable from 0.001…10.00 kWh/kVARh per pulse. ≥100 ms <120 ms (ON), ≥120 ms (OFF),
according to EN62052-31
Communication controlled outputs The activation of the outputs is managed through the serial communication port
Insulation See Table 44 Isolation Between Inputs and Outputs (1 minute)

Technical Specifications Appendix B
Table 37 - Analog Output Specifications (A option)

Attribute Value
Number of outputs 2
Accuracy (at 25 °C ±5 °C, R.H. ≤ 60%) ± 0.2% of full scale
Range 0…20 mA
Configuration By using the front keypad
Signal retransmission The signal output can be connected to any instantaneous variable. See List of Connectable Variables on page 74
Scaling factor Programmable within the whole range of retransmission; it allows the retransmission management of all values from
0…20 mA DC
Response time ≤400 ms typical (filter excluded)
Ripple ≤1% (according to IEC 60688-1, EN 60688-1)
Total temperature drift ≤500 ppm/°C
Load ≤ 600 Ω
Table 38 - Serial RS-485/RS-232 Communication Specifications (485 option)

Attribute Value
RS-485/RS-422 port
Type Multidrop, bidirectional (static and dynamic variables)
Connections 2-wire Max distance 1000 m, termination directly on the module
Addresses 247, selectable by using the front key-pad or through the software
Protocol Modbus RTU
Data (bidirectional)
Dynamic (reading only) System and phase variables: see the Modbus register maps in Appendix A
Static (reading and writing only) All configuration parameters; see the Modbus register maps in Appendix A
Data format One start bit, eight data bit, no/even/odd parity, 1 stop bit
Communication rate Selectable: 9.6, 19.2, 38.4, 115.2 Kbps
Driver input capability 1/5 unit load. Max 160 transceivers on the same bus
RS-232 port
Type Bidirectional (static and dynamic variables)
Connections Three wires. Max distance 15 m
Protocol Modbus RTU

Table 38 - Serial RS-485/RS-232 Communication Specifications (485 option)

Attribute Value
Data (bidirectional)
Dynamic (reading only) System and phase variables: see the Modbus register tables in Appendix A
Static (reading and writing only) All configuration parameters; see the Modbus register tables in Appendix A
Data format One start bit, eight data bit, no/even/odd parity, 1 stop bit
Communication rate Selectable: 9.6, 19.2, 38.4, 115.2 Kbps
Note With the rotary switch (on the back of the basic unit) in lock position, modification of programming parameters and
reset command with serial communication are not allowed. In this case, just the data reading is allowed
Table 39 - Energy Meters

Attribute Value
Meters
Total 4 (9+1 digit)
Partial 4 (9+1 digit)
Pulse output Connectable to total and/or partial meters
Energy meter recording Storage of total and partial energy meters. Energy meter storage format (EEPROM)
Min. -9,999,999,999.9 kWh/kVARh
Max. 9,999,999,999.9 kWh/kVARh
Energy meters
Total energy meters +kWh, +kVARh, -kWh, -kVARh
Partial energy meters +kWh, +kVARh, -kWh, -kVARh
Table 40 - Display, Status Indicators, and Commands

Attribute Value
Display refresh time ≤ 100 ms
Display Four Rows of display each with a max of four digits,
1 Row of display with a max of 10 digits
Type LCD, single color backlight
Digit dimensions Four digits: h 9.5 mm; 10 digits: h 6.0 mm
Instantaneous variables read-out Four digits
Energy variables read-out Imported Total/Partial: 9+1 digit or 10 digits;
Exported Total/Partial: 9+1 digit or 10 digits (with ‘-’ sign)
Run hours counter 8+2 digits (99,999,999 hours and 59 minutes max)
Overload status EEEE indication when the value being measured is exceeding the ‘Continuous inputs overload’ (max measurement
capacity)
Max and min indication Max instantaneous variables: 9999; energies: 999,999,999.9 or 9,999,999,999
Min instantaneous variables: 0.000; energies 0.0
Front-position Status Indicators
Virtual alarms Four red status indicators available in case of virtual alarm (AL1-AL2- AL3-AL4).
The real alarm is just the activation of the proper static or relay output if the proper module is available
Energy consumption Red status indicator (only kWh)

Table 40 - Display, Status Indicators, and Commands

Attribute Value
kWh pulsating 0.001 kWh/kVARh by pulse if the Ct ratio by VT ratio is ≤ 7
0.01 kWh/kVARh by pulse if the Ct ratio by VT ratio is ≥7.1 ≤ 70.0
0.1 kWh/kVARh by pulse if the Ct ratio by VT ratio is ≥70.1 ≤700.0
1 kWh/kVARh by pulse if the Ct ratio by VT ratio is ≥700.1 ≤ 7000
10 kWh/kVARh by pulse if the Ct ratio by VT ratio is ≥7001 ≤ 70.00k
100 kWh/kVARh by pulse if the Ct ratio by VT ratio is >70.01k
Max frequency: 16 Hz, according to EN50470-1
Rear-position Status Indicators
On the base Green as power-on
On communication modules Two status indicators: one for TX (green) and one for RX (amber)
Key-pad For variable selection, programming of the instrument working parameters, ‘dmd’, ‘max’, total energy, and partial energy
Reset
Table 41 - Main Functions

Attribute Value
Password Numeric code of max four digits; two protection levels of the programming data
1st level Password ‘0’, no protection
2nd level Password from 1…9999, all data are protected
System selection
System 3P.n unbalanced load 3-phase (4-wire Wye)
System 3P unbalanced load 3-phase (3-wire) Delta
Three currents and three line-to-line voltage measurements
For ARON connection, two currents (with special wiring on screw terminals) and three line-to-line voltage
measurements.
System 3P.1 balanced load 3-phase (3-wire), one current and three line-to-line measurements.
3-phase (4-wire), one current and three line-to-neutral voltage measurements.
System 3P.2 balanced load 3-phase (2-wire), one current and one line-to-neutral (L1) voltage measurement
System 2P 2-phase (3-wire) Split-phase
System 1P 1-phase (2-wire) Single phase
Transformer ratio
VT (PT) 1.0…999.9 / 1000…9999
CT 1.0…999.9 / 1000…9999 (up to 50 kA in case of CT with 5 A secondary current)
Filter
Operating range Selectable from 0…100% of the input display scale
Filtering coefficient Selectable from 1…256
Filter action Measurements, analog signal retransmission, serial communication (fundamental variables: V, A, W, and their derived
ones)
Displaying
Number of variables Up to five variables per page. See Front Panel Features on page 9. Seven different set of variables available according to
the application being selected. See Display Features on page 11
Backlight The backlight time is programmable from 0 (always on) to 255 minutes

Table 41 - Main Functions

Attribute Value
Virtual alarms
Working condition Basic unit (indication only) or with (P) optional digital output modules
No. of alarms Up to 4
Working mode Up alarm and down alarm
Controlled variables The alarms can be connected to any instantaneous variable. See List of Connectable Variables on page 74
Set-point adjustment From 0…100% of the display scale
Hysteresis From 0 to full scale
On-time delay 0…9999 s
Response time, min ≤ 200 ms, filters excluded. Set-point on-time delay: ‘0 s’
Reset By using the front keypad. It is possible to reset the following data:
• All max and dmd values
• Total energy (kWh, kVARh)
• Partial energy (kWh, kVARh)
Clock
Functions Universal clock and calendar
Time format Hour: minutes: seconds with selectable 24 hours or AM/PM format
Date format Day-month-year with selectable DD-MM-YY or MM-DD-YY format
Battery life Ten years
Easy connection function For all display selections, both energy and power measurements are independent from the current direction. The
displayed energy is always ‘imported’
Table 42 - General Specifications

Attribute Value
Temperature, operating -25…40 °C (-13…104 °F) (R.H. from 0…90% noncondensing at 40 °C) according to EN62053-21, EN50470-1 and
EN62053- 23
Temperature, storage -30…70 °C (-22…158 °F) (R.H. < 90% noncondensing @ 40 °C) according to EN62053-21, EN50470-1 and EN62053- 23
Installation category Cat. III (IEC60664, EN60664)
Dielectric strength 4 kV AC rms for 1 minute
Noise rejection CMRR 100 dB, 48…62 Hz
EMC According to EN62052-11
Electrostatic discharge 15 kV air discharge
Immunity to radiated electromagnetic fields Test with current: 10V/m from 80…2000 MHz
Test without any current: 30V/m from 80…2000 MHz
Burst On current and voltage measuring inputs circuit: 4 kV
Immunity to conducted disturbances 10V/m from 150 KHz…80 MHz
Surge On current and voltage measuring inputs circuit: 4 kV; on ‘L’ auxiliary power supply input: 1 kV
Radio frequency suppression According to CISPR 22
Standard compliance
Safety IEC60664, IEC61010-1 EN60664, EN61010-1
Metrology EN62052-11, EN62053-21, EN62053-23, EN50470-3

Table 42 - General Specifications

Attribute Value
Pulse output DIN43864, IEC62053-31
Approvals CE, cULus (E56639)
Connections Screw-type
Cable cross-section area Max 2.5 mm2 (14 AWG)
Screw tightening torque: 0.4 N•m min/0.8 N•m max
Suggested screw tightening torque: 0.5 N•m
Housing DIN
Dimensions (WxHxD) Module holder: 96 x 96 x 50 mm
Digital and analog output modules: 89.5 x 63 x 16 mm
Serial and Ethernet Communication modules: 89.5 x 63 x 20 mm
Depth behind panel, max 81.7 mm
Material ABS, self-extinguishing: UL 94 V-0
Mounting Panel mounting
Pollution degree 2
Protection degree, front(1) IP65, UL Type 4x indoor (NEMA4x indoor), UL Type 12 (NEMA12), for use on flat surface of a Type 4X Indoor enclosure; for
use on flat surface of a Type 12 enclosure.
Protection degree, screw terminals IP20
Weight, approx 400 g (0.88 lb) (packing included)
(1) Use with 60 °C or 70 °C copper conductor. Maximum surrounding air temperature 40 °C. Install the device in a pollution degree 2 environment. Open Type Device. The terminals L1, L2, and L3 are
acquired by a circuit where devices or system, including filters or air gaps, are used to control overvoltages at the maximum rated impulse withstand voltage peak of 6.0 kV. Devices or system is
evaluated by using the requirements in the Standard for Transient Voltage Surge Suppressors, UL 1449. Tighten terminals to 0.79 N•m (7 lb•in). The sum of the internal power consumption of the
assembled modules is not be more than 5.3 W.
Table 43 - Power Supply Specification

Attribute Value
Auxiliary power supply Nominal: 120/240V AC (50/60 Hz) or 120/240V DC
Range: 100…240V AC (48…62 Hz)
Power consumption 6VA
Table 44 - Isolation Between Inputs and Outputs (1 minute)

Measuring Inputs Relay Outputs Communication Analog Outputs Auxiliary Power
Port Supply
Measuring Inputs - 4 kV 4 kV 4 kV 4 kV
Relay outputs 4 kV 2 kV 4 kV 4 kV 4 kV
Communication port 4 kV 4 kV - 4 kV 4 kV
Analog Outputs 4 kV 4 kV 4 kV 0 kV 4 kV
Aux. power supply 4 kV 4 kV 4 kV 4 kV -
TIP The channel isolation of the current inputs is 100V AC maximum and
therefore require external current transformers.

List of Connectable Variables The variables that are listed in this table can be connected to the following
items:
• Analog outputs (all variables except energy values and run hour counter)
• Pulse (digital relay)outputs (only energy values)
• Alarms (except energy, hour counter, and max values)
(X) = available; (O) = not available (variable not available on the display);
(#) Not available (the relevant page is not displayed); (1) Max value with data
storage
Table 45 - Variables
No Variable 1-ph. Sys (1P) 2-ph. Sys (2P) 3-ph. 3/4-wire 3-ph. 2-wire 3-ph. 3-wire 3-ph. 4-wire Notes
Balanced Sys Balanced Sys Unbal. Sys (3P) Unbal. Sys
(3P.1) (3P.2) (3P.n)
1 VL-N sys O X X X # X sys= system=  (1)
2 VL1 X X X X # X (1)
3 VL2 O X X X # X (1)
4 VL3 O O X X # X (1)
5 VL-L sys O X X X X X sys= system= (1)
6 VL1-2 # X X X X X (1)
7 VL2-3 # O X X X X (1)
8 VL3-1 # O X X X X (1)
9 AL1 X X X X X X (1)
10 AL2 O X X X X X (1)
11 AL3 O O X X X X (1)
12 VA sys X X X X X X sys= system=  (1)
13 VA L1 X X X X # X (1)
14 VA L2 O X X X # X (1)
15 VA L3 O O X X # X (1)
16 var sys X X X X X X sys= system=  (1)
17 var L1 X X X X # X (1)
18 var L2 O X X X # X (1)
19 var L3 O O X X # X (1)
20 W sys X X X X X X sys= system=  (1)
21 WL1 X X X X # X (1)
22 WL2 O X X X # X (1)
23 WL3 O O X X # X (1)
24 PF sys X X X X X X sys= system=  (1)
25 PF L1 X X X X # X (1)
26 PF L2 O X X X # X (1)
27 PF L3 O O X X # X (1)
28 Hz X X X X X X (1)
29 Phase seq. O X X X X X
30 Run Hours X X X X X X

Table 45 - Variables
No Variable 1-ph. Sys (1P) 2-ph. Sys (2P) 3-ph. 3/4-wire 3-ph. 2-wire 3-ph. 3-wire 3-ph. 4-wire Notes
Balanced Sys Balanced Sys Unbal. Sys (3P) Unbal. Sys
(3P.1) (3P.2) (3P.n)
31 kWh (+) X X X X X X Total
32 kVARh (+) X X X X # X Total
33 kWh (+) X X X X X X Partial
34 kVARh (+) X X X X # X Partial
35 kWh (-) X X X X X X Total
36 kVARh (-) X X X X # X Total
37 kWh (-) X X X X X X Partial
38 kVARh (-) X X X X # X Partial
Figure 26 - Accuracy
kWh, Accuracy (RDG) Depending on the Current kvarh, Accuracy (RDG) Depending on the Current
Percentage error limits for class index B Error (uncertainty)
+1.5% +2.5%
+1.0% +2.0%
0% 0%
-1.0% -2.0%
-1.5% -2.5%
PF=1 0.05A (Imin) 0.25A (I tr ) 5A (I n ) 6A (Imax ) sin φ=1 0.1A 0.25A 5A (In ) 6A (Imax )
PF=L0.5 0.25A (I tr ) 5A (I n ) 6A (Imax ) sin φ=0.5 0.25A 0.5A 5A (In ) 6A (Imax )

or C0.8
Accuracy limits (Real energy) Accuracy limits (Reactive energy)
Start-up current: 5 mA Start-up current: 5 mA

Figure 27 - Calculation Formulas

Phase variables Systemvariables Three-phase power factor
(TPF)
Instantaneous effective voltage Equivalent three-phase voltage
Instantaneous real power

Energy metering
Three-phase reactive power
Instantaneous power factor

Three-phase real power
Instantaneous effective current Three-phase apparent power

Where:
i= considered phase (L1, L2 or L3)
Instantaneous apparent power P = real power; Q = reactive power;
t 1 , t 2 =starting and ending time points
of consumption recording; n = time
unit; Δ t= time interval between two
Instantaneous reactive power successive power consumptions;
n 1 , n 2 = starting and ending discrete
time points of consumption recording

Appendix C
PowerMonitor 500 EtherNet/IP Device Profile
This section describes the specific CIP Objects, Instances, Attributes, and
Services that are supported by the PowerMonitor™ 500 system. This information
is for anyone wishing to integrate the PowerMonitor 500 system into existing or
planned shop floor networks.
General For this device profile, we use a PowerMonitor 500 unit and an EtherNet/IP
communication module to provide power and energy metering data via an
EtherNet/IP network. The data is accessed as instances of the device Assembly
Object.
This profile documents objects that are proprietary, or in some way that is altered
from their generic behavior. Standard CIP objects that are generic in their
interface are documented in the EtherNet/IP specification.
Object Model and Interface The PowerMonitor 500 system is represented by the following Object Model.
Object Class Class Code Instance Numbers Number of Connections
Identity 0x0001 1 0
Assembly 0x0004 100d…108d 18
Identity Object - CLASS CODE The Identity Object is used to provide identification information about the
device. Each node supports at least one instance of the identity object. The
0x0001 Identity Object is used by applications to determine which nodes are on the
network. The Identity Object supports Class Attributes (Instance 0) and
Instance 1.
See Section 5-2 of the CIP Common Specification for full details of this object.

Appendix C PowerMonitor 500 EtherNet/IP Device Profile
Identity Object Class Attributes (Instance 0)

Attr ID Access Name Data Type Default Value
0x01 Get Revision UINT 1
0x02 Get Max Instance UINT 1
0x03 Get Number of UINT 1
Instances(1)
0x06 Get Maximum ID UINT 7
Number Class
Attributes
0x07 Get Maximum ID UINT 7
Number Instance
Attributes
(1) Attribute ID 0x03 is not returned for service type Get Attribute All.
Instance 1 (PowerMonitor 500 device and Communication module)
Instance 1 represents the PowerMonitor 500 device with its EtherNet/IP

module. Instance 1 of the Identity Object is the one that is browsed by RSLinx®
software, relevant to the complete device, that is, the PowerMonitor 500 device
and Communication module.
Instance 1 of the Identity Object reports the following instance-specific attribute

values.
Identity Object Instance 1 Attributes

Attribute ID Access Name Data Type Value
0x01 Get Vendor ID UINT 1 (Rockwell Automation)
0x02 Get Device Type UINT 0x92 (146d)
0x03 Get Product Code UINT See Product Code Values table
0x04 Get Revision Struct of: Dynamic (varies with the
communication firmware
Major Revision USINT revision)
Minor Revision USINT
0x05 Get Status WORD Dynamic
0x06 Get Serial Number UDINT 940000000…950000000
0x07 Get Product Name SHORT_STRING PowerMonitor 500

PowerMonitor 500 EtherNet/IP Device Profile Appendix C
Product Code Values

Part Number Name Product Description
Code
1420-V1-ENT 146 - PowerMonitor 500 4 PowerMonitor 500 (240V AC, No I/O)
Catalog Number 1420-V1-ENT
1420-V1P-ENT 146 - PowerMonitor 500 5 PowerMonitor 500 (240V AC, Digital I/O)
Catalog Number 1420-V1P-ENT
1420-V1A-ENT 146 - PowerMonitor 500 6 PowerMonitor 500 (240V AC, Analog I/O)
Catalog Number 1420-V1A-ENT
1420-V2-ENT 146 - PowerMonitor 500 7 PowerMonitor 500 (600V AC, No I/O)
Catalog Number 1420-V2-ENT
1420-V2P-ENT 146 - PowerMonitor 500 8 PowerMonitor 500 (600V AC, Digital I/O)
Catalog Number 1420-V2P-ENT
1420-V2A-ENT 146 - PowerMonitor 500 9 PowerMonitor 500 (600V AC, Analog I/O)
Catalog Number 1420-V2A-ENT
Identity Object Services

Service Code Class/Instance Usage Service Name
0x01 Class/Instance Get_Attributes_All
0x0E Class/Instance Get_Attribute_Single

Get Attribute All Service
The Get Attribute All service returns a concatenation of all class or instance
attributes.
The following example shows how to configure your message instruction

configuration for the Get Attribute All Service type for the Logix Designer
application. In this example, we read the class attributes (Instance 0) of the
Identity Object.
Parameter Choice Notes

Message Type CIP Generic
Service Type Custom
Service Code 1 (hex) 1 = Get Attribute All
e = Get Attribute Single
Instance 0 0 = Identity Object Class Attributes
1 = Identity Object Instance 1 Attributes
Class 1 (hex) 1 = Identity Object
Attribute 0 (hex) This parameter is irrelevant for Get Attribute All service, but a value must be
entered in this parameter for the Customer service type.
Source Element See Notes This element is irrelevant for the Get Attribute All service, however it must be
completed for the Custom service type. In this example, the Source Element
and the Destination Element are set to the same array.
Source Length See Notes This parameter is irrelevant for the Get Attribute All service but must be
completed. The value can be less than or equal to the Source Element byte size
to avoid error.
Destination See Notes This element is the first element of the controller tag that stores the data being
Element read. The tag is an array of the applicable data type the same length as the
Identity Instance. In this example, the tag is an array of five INT elements.

Get Attribute Single Service
The Get Attribute Single service returns the single attribute that is specified by
the parameter Attribute ID.
Request Parameters
Parameter Data Type Description
Attribute ID UINT Identifies the attribute to be read/returned
The following example shows how to create your message instruction

configuration for the Get Attribute Single Service type for the Logix Designer
application. In this example, we read the Instance 1 attributes of the Identity
Object.

Service Type Get Attribute Single
Service Code e (hex) e = Get Attribute Single
Instance 1 0 = Identity Object Class Attributes
1 = Identity Object Instance 1 Attributes
Class 1 (hex) 1 = Identity Object
Attribute 3 (hex) This parameter is the attribute ID of the specific attribute to be read. In
this example, 3 = Product Code.
Source Element N/A Not applicable to a Read
Source Length N/A Not applicable to a Read
Destination Element See Notes This element is the first element of the controller tag that stores the
data being read. The tag is an array of the applicable data type the
same length as the Attribute. In this example, the tag is an array of
one INT element.

Assembly Object - CLASS CODE The Assembly Object collects attributes from multiple objects, allowing data to
or from each object to be sent or received over a connection. Assembly Objects
0x0004 are used to produce and/or consume data to/from the network. An instance of
the Assembly Object can both produce and consume data from the network.
Static assemblies are factory determined and cannot be modified. Members

cannot be added or deleted. The implementation of the Assembly Object are
static. See Section 5-5 of the CIP Common Specification for full details of this
object.
Assembly Object Class Attributes

0x01 Get Revision UINT 2
0x02 Get Max Instance UINT 108d
0x03 Get Number of Instances UINT 9
0x04 Get Optional Attributes List STRUCT of UINT 0x0001,
ARRAY of UINT {0x0004}
0x06 Get Maximum ID Number Class UINT 7
Attributes
0x07 Get Maximum ID Number Instance UINT 4
Attributes
Assembly Object Instance Attributes

0x03 Get Data Instance Dependent (1) All member data that is packed
into one array.
0x04 Get Size Size (in bytes) of the Data attribute Instance Dependent(1)
(1) See Chapter 4 for more information.

Assembly Object Instances
The communication module Assembly Object supports nine instances (instances

100d to 108d). The Data attributes of these instances can be accessed via Class 1
scheduled connections and via Class 3 or UCMM unscheduled connections.
See Appendix A, PowerMonitor 500 EtherNet/IP Device Profile for more

information on the content of the Assembly Instances.
Assembly Instance Size (No. of elements) Data Type Data Table Description
100 20 UINT Product Information
101 12 REAL Real-time Voltage and Current
102 18 REAL Real-time Power, PF, Frequency
103 12 REAL Max Voltage and Current
104 17 REAL Max Power, PF, Frequency
105 12 REAL Demand Voltage and Current
106 17 REAL Demand Power, PF, Frequency
107 18 REAL Energy Meters
108 2 UINT Alarm and Output Status
Assembly Object Services

Service Code Class/Instance Usage Service Name
0x0E Class/Instance Get Attribute Single

Get Attribute Single Service
The Get Attribute Single service returns the single attribute that is specified by
the parameter Attribute ID.
The following example shows how to create your message instruction

configuration for the Get Attribute Single Service type for the Logix Designer
application. In this example, we read the Instance 102 attributes of the Assembly
Object.

Service Type Get Attribute Single
Service Code e (hex) e = Get Attribute Single
Instance 102 This parameter is the Assembly Instance of the specific
data table to be read. In this example, 102 = Real-time
Power, PF, Frequency
Class 4 (hex) 4 = Assembly Object
Attribute 3 (hex) 3 = Data
4 = Size of data
Source Element N/A Not applicable to a Read
Source Length N/A Not applicable to a Read
Destination Element See Notes This element is the first element of the controller tag that
stores the data being read. The tag is an array of the
applicable data type the same length as the Attribute. In
this example, the tag is an array of 18 REAL elements.

Connections
The Assembly Object supports both scheduled (Class 1) and unscheduled

connections (Class 3 and UCMM). Both connections are used to access
instances 100d to 108d of the Assembly Object:
• UDP - Nine Class 1 connections each to the nine Assembly Instances 100
to 108 at 100 ms RPI ran stable
• TCP - Nine Class 3 connections each to the nine Assembly Instances 100
to 108 at 200 ms RPI ran stable
• Both - UDP and TCP can run simultaneously
Heartbeat Instances
With the Assembly Instances shown earlier, the communication module also
recognizes two heartbeat instances. A heartbeat instance is a virtual output
instance that is specified by devices wishing to establish Input Only and Listen
Only Class 1 I/O connections to the communication module. Data cannot be
read from or written to a heartbeat instance. The heartbeat instance is merely a
programming construct that serves to keep the connection active.
The communication module heartbeat instances are Instance 98 for the Input
Only connection and Instance 99 for the Listen Only connection.
Behavior
The purpose of the Assembly Object is to act as a network interface to the

PowerMonitor 500 unit data. That data is accessed by various means: Class 1 or
Class 3 connections and also with UCMM messages.
Technical Notes This section lists additional technical information about Ethernet network
communication.
Parameters
For the EtherNet/IP communication module, set the following parameters by

using Programming mode through the base module front panel:
• IP address
• Subnet
• Gateway
• Modbus TCP/IP port
• Address Conflict Detect (ACD)

Modbus TCP/IP
The communication module supports Modbus TCP/IP. The protocol is the

same as the PowerMonitor 500 unit with RS-485 (Modbus RTU). See Chapter 4
for protocol details. In this product, only one Modbus TCP/IP connection (one
socket) is allowed.
The EtherNet/IP and Modbus TCP/IP do not run concurrently. If

ModbusTCP/IP communication occurs, EtherNet/IP communication stops
temporarily but recovers in a minute or two.
IMPORTANT We recommend that you use Modbus TCP/IP to configure or write to the
PowerMonitor 500 unit and that you use Ethernet/IP to read the PowerMonitor
500 unit.
ACD
If an address conflict is detected from the communication module, then the base
module displays ‘ACD Found’. In that case, it is necessary to check the network
configuration, resolve the problem, and then cycle control power to the power
monitor to re-establish communication.
TCP/IP Port
Default EtherNet/IP ports include the following:

• UDP (implicit message): 2222 (0x08AE)
• TCP (explicit message): 44818 (0xAF12)
You can reassign the default Modbus TCP/IP port: 502 (0x01F6).

Appendix D
Unit Configuration - Base Firmware Revision 11

and Earlier
Configure with the Display The PowerMonitor™ 500 unit provides menu-based configuration
(programming) by using its front panel display. The programming menus let
you select parameters to edit, select digits within parameters, and increase or
decrease the value of each digit.
Place the unit in Programming mode by pressing Program/select (8) for about
2 seconds. The front panel displays the PASSWORD? menu page 0 in Editing
mode. Enter the correct password by using the Up and Down arrows (the
default password is 0) and press Program/select. The front panel then displays
the CHANGE PAS menu page 10.
See the programming flowchart that begins on page 90 for a view of the
organization of programming menus and submenus. Each page is identified
with a number, which is displayed in the top right corner. Menu page numbers
end in zero, while submenu pages end in 1 through 9. For example, the Change
Password page is menu 10. Likewise, the Dmd page is menu 80, and the
demand interval Time page is menu 82.
While you are programming the power monitor, the display items and control
buttons function one way when you are navigating between menu or submenu
pages, and another way when you are editing a menu page.

Appendix D Unit Configuration - Base Firmware Revision 11 and Earlier
Figure 28 - Front Panel Display
3
6
4
5 7
Table 46 - Front Panel Display Descriptions

Display Item Description Navigating Menus Editing a Menu
1 Programming mode indicator Indicates programming mode.
2 Programming menu page Identifies the current programming menu page. See the programming flowchart that begins on page 90.
3 Editing mode indicator Does not appear. Indicates the parameter being edited.
4 Cursor Does not appear. Appears beneath the digit currently being edited.
5 Permitted range Displays the permitted range of values for the selected parameter.
6 Exit button • When in a menu page, exits Programming mode • Moves the cursor one digit to the left.
without saving changes. Program/select button • When the leftmost digit is selected, dP is
confirms exit. indicated and you can change the decimal point
• When in a submenu page, exits to menu page. and multiplier (see Edit Decimal Point and
Multiplier on page 89).
• When held for at least 2 seconds, cancels the edit
and restores the previous value of the selected
parameter.
7 Up button Selects the next higher-numbered menu or • Increments the value of the digit indicated by the
submenu page. cursor.
• When dP is indicated, increments the decimal
Down button Selects the next lower-numbered menu of submenu • Decrements the value of the digit indicated by
page. the cursor.
• When dP is indicated, decrements the decimal
8 Program/select button • Press and hold for 2 seconds to enter the Program Stores the new value of the selected parameter, but
mode. does not save the new configuration to the power
• Selects a menu page for editing. monitor.
• When in a menu page with submenus, displays
the first submenu page.
• After pressing the Exit button, confirms exit from
Programming mode without saving changes.
• From End menu page 260, saves new
configuration and exits Programming mode.

Unit Configuration - Base Firmware Revision 11 and Earlier Appendix D
IMPORTANT To save programming changes, navigate to the End menu page 260 and
press Program/select. To exit the Programming mode without saving any
changes, press Exit and confirm by pressing Program/select. If no buttons
have been pressed for 2 minutes, the power monitor exits Programming
mode without saving any changes.
TIP You can make programming changes by using the PowerMonitor 500
software.
Edit Decimal Point and Multiplier

When the cursor is beneath the last digit on the left, pressing Exit (6) lets you
change the decimal point and the multiplier (9) (k or M). The blinking ‘dP’
(decimal point) text (10) indicates this capability.
10
To modify the decimal point position and the multiplier, use the Up and
Down arrow (7) to select the desired value.

Configuration Flowchart The following flowchart shows the configuration menus and submenus that
are accessed through the display. To navigate through the menu pages, use the
up and down arrows. To enter Edit mode or to access a submenu, press the
Program/select button. The menu pages available depend on your module
type.
• 0 PASSWORD?: enter password by using up and
down arrows to change the digit. Use the Exit button
to move the cursor between digits. Press the
Program/select button to confirm password. The
default password is 0.
• 10 CHANGE PAS: this function lets you modify the
PASS value with a new value (from 0…9999).
• 20 BACKLIGHT: adjusts backlight time from
0…255 minutes (0 = always on).
• 50 SYSTEM: this function lets you select the type of
electrical system.
See pages 19…22 for descriptions and wiring
diagrams that correspond to the system type
designations, such as, 3P and 3P.n.
• 60 CT RATIO: this function lets you select the value
of the CT ratio (primary/secondary ratio of the
current transformer being used). Example: if the CT
primary (current transformer) has a current of 300 A
and the secondary a current of 5 A, the CT ratio
corresponds to 60 (300 divided by 5).
• 70 PT RATIO: this function lets you select the value
of the PT (VT) ratio (primary/secondary ratio of the
potential/voltage transformer being used). Example:
if the primary of the connected PT is 20 kV and the
secondary is 100V, then the PT ratio corresponds to
200 (20,000 divided by 100). If the voltage level is
such that PTs are not required and are not in place,
configure the PT ratio to 1.0.

• 80 DMD: This function lets you select the calculation

method of the DMD/AVG value of the selected
variable.
– 81 TYPE: select the type of Calculation mode to be
used for the DMD/AVG calculation.
FIXED: The instrument calculates the
AVG/DMD value of the measured variable over the
selected interval, updates the AVG/DMD value at
the end of the interval, then resets and starts a new
calculation.
SLIDE: When first configured, the instrument
calculates the AVG/DMD value and updates its
value at the beginning after the first selected
interval. After the first interval, the instrument
calculates the AVG/DMD value every minute.
After the calculation, the instrument generates a
window whose width is the selected interval and
Fixed
that moves forward every minute.
– 82 TIME: select the time interval for the DMD/
AVG calculation. Default is 15 minutes.
– 83 SYNC: select the Synchronization mode. That
mode is the method that controls the calculation
method of the average/demand according to the
selected time.
Where:
Pmax is the maximum power
Pc is the contractual power • 110 FILTER: The digital filter makes it possible to
t1 is the selected time period for the calculation of the AVG/DMD value
stabilize the display of fluctuating measurements.
Slide
See Digital Filtering Operation on page 33.
– 111 FILTER S: set the operating range (span) of the
digital filter. The value is expressed as a % (filter to
0.0 means filter excluded).
– 112 FILTER CO: set the filtering coefficient of the
instantaneous measures. By increasing the value, also
the stability and the settling time of the measures are
increased.
IMPORTANT: Some specific menus display only if
the relevant modules are installed.

• 120 RS232-485: User settings for the RS-232 and RS-

485 serial communication ports.
• 130 ETHERNET: User settings for the Ethernet
communication port.
-IP ADDRESS www.xxx.yyy.zzz • 150 VIRT AL 1: This virtual alarm function lets you
set the alarm parameters.
-SUBNET www.xxx.yyy.zzz
ETHERNET
– 151 ENABLE: enable (YES) or disable (NO) the
-GATEWAY www.xxx.yyy.zzz
alarm.
-TCP IP PRT 1…9999 (default = 502)
– 152 VARIABLES: set the variable to be linked to
-ACD yes/no (default = no) the alarm.
– 153 SET 1: set the on alarm set point of the variable.
list of available – 154 SET 2: set the off alarm set point of the variable.
variables
– 155 ON DELAY: set a delay on activation of the
alarm.
• 190 DIG OUT 1: This function lets you link a virtual
alarm to the digital relay output and to its working
Same as VIRT ALARM 1 parameters.
– 191 FUNCTION:
Same as VIRT ALARM 1
Alarm - the digital output is enabled when the
Same as VIRT ALARM 1 associated alarm status occurs.
Pulse - the measured energy is retransmitted by the
digital output with pulses.
Remote - the digital output can be controlled
through a command that is sent through the serial
list of available
variables communication port.
– 192 AL LINK: select the virtual alarm that it has to
be associated.
– 193 AL STATUS: ‘ND’ (normally de-energized
relay) or ‘NE’ (normally energized relay).
Same as DIG OUT 1
– 195 PULSE WEIG: selects the pulse weight (kWh
per pulse).
– 196 OUT TEST: Tests the digital output. YES
enables the test, No disables the test.
– 197 POWER TEST: sets a simulated power value
(kW) to test the energy pulse output. The function
remains active until you exit the programming
menu.

• 210 AN OUT 1: User programming of the analog

List of available outputs (0…20 mA).
variables
– 211 VARIABLES: selects the variable to be
retransmitted with the analog output.
– 212 MIN OUTPUT: sets the value that is expressed
as % of the output range (0…20 mA) that
corresponds to the minimum measured value.
– 213 MAX OUTPUT: selects the value that is
expressed as % of the output range (0…20 mA) that
corresponds to the maximum measured value.
Same as AN OUT 1
– 214 MIN INPUT: minimum value of the variable
input range, corresponds to the ‘MIN OUTPUT’
– 215 MAX INPUT: maximum value of the variable
input range corresponds to the ‘MAX OUTPUT’
• 230 METERS: reset the ENERGY METERS. Choose
among the following:
– 231 TOTAL, 222 PARTIAL: resets all energy
meters, total and partial.
– 233 TOTAL +: resets the total meters of imported
energy.
– 234 TOTAL -: resets the total meters of exported
energy.
– 235 PARTIAL +: resets the partial meters of
imported energy.
– 236 PARTIAL -: resets the partial meters of
exported energy.
• 240 RESET: Resets the MAX or dmd stored values.
• 250 CLOCK:
– 251 FORMAT: UE, sets the European time format
as 24h (00:00) or sets the time format as 12h
(12:00 AM/PM).
– 252 YEAR: sets the current year.
– 253 MONTH: sets the current month.
– 254 DAY: sets the current day.
– 255 HOUR: sets the current hour.
Save the set – 256 MINUTE: sets the current minute.
parameters and come
back to the measuring – 257 SECOND: sets the current second.
mode. • 260 END:
– To save programming changes, press Program/select.
– To exit the Programming mode without saving any
changes, press Exit and confirm by pressing
Program/select.
– If no buttons are pressed for two minutes, the unit
exits Programming mode without saving changes.

Notes:

Index
Numerics current transformer wiring 17

485 option 69
D
A data tables 49
A option 69 data types supported 46
decimal point change 27, 89
about PowerMonitor 500 7
diagrams,wiring 17
access information pages 13
digital filter programming examples 33 …
accuracy 8, 75
35
additional button functions 10
digital filtering operation 33
address
digital output specifications 68
Modbus 46
physical 46 digital outputs wiring 21
alarm configuration 37 dimensions 8, 15
alarm icons 11 optional modules 15
analog output specifications 69 display 8, 11
analog outputs 21 alarm icons 11
features 11
configuration 36, 61
icons 11
display description 26, 88
B display specifications 70
billing 7
buttons 9 E
additional functions 10 electronic data sheet 40
descriptions 26, 88
energy metering values 59
energy meters specifications
C specifications
calculation formulas 76 energy meter 70
entering password 25, 87
catalog number explanation 5
EtherNet/IP communication 39
change
assembly object 82
decimal point 27, 89 assembly object instances 83
multiplier 27, 89
byte order 39
CIP generic 40
common services 83
class 1 42 device profile 77
comman specifications 70 explicit messaging 40
commands 63 identity object 77
communication identity object instance attributes 78
implicit messaging 42
EtherNet⁄IP 8
Modbus TCP/IP 45
Modbus 8, 45
technical notes 85
ports 7 explicit messaging 40
RS-232 8, 45
RS-485 8, 45
communication commands 39
configurable alarms 8
F
configuration 25, 87 factory installed options
alarm 37 modules 15
analog output 36 wiring 21
analog outputs communication 61 FactoryTalk EnergyMetrix 7
relay outputs communication 62 features 7
RS-232 communication 60 filter CO 33
RS-485 communication 60 filter S 33
configuration alarms 60
formulas 76
configuration base unit 59 front panel
configuration flow chart 28 … 32, 90 … 93
buttons 9, 26, 88
control 7 indicators 9
cost allocation 7 functions 7

Index
G password 25, 87
general specifications 72 physical address 46
ports
geometric representation 50
ground connection 46 EtherNet/IP 7
RS-485/RS-232 7
power and power factor
I geometric representation 50
power supply 8
icons power supply wiring 21
alarm 11 power system
display 11
IEC vs NEMA diagrams 17 monitoring 7
power system control 7
implicit messaging 42
PowerMonitor 500
indications 11
about 7
indicators 9 configuration 25, 87
information access 13 cut-out 15
input specifications 67 dimensions 15
installation 15, 16 features 7
functions 7
IP65 7, 8
installation 15
isolation between inputs and outputs 73 panel installation 16
wiring terminals 16
product information 51
L programming mode 25, 87
line amplifier 46 25, 87
list of variables 74 … 75 protection
load profiling 7 IP65 7, 8
NEMA 12 8
NEMA 4X 8
M pulse output specifications 68
main functions specifications 71
menu page numbers 25, 87 R
message setup 40, 42 real-time metering demand 56, 57
Modbus real-time metering values 52, 53, 54, 55
address 46 register format 47
commands 63
communication 45 register maps 51
configure alarms 60 relay outputs
configure base unit 59 configuration 62
data types supported 46 RS-232 45
energy metering values 59 configuration 60
functions supported 45 wiring 22
real-time metering demand 56, 57 RS-485 45
real-time metering values 52, 53, 54, 55
configuration 60
register format 47
wiring 22
register maps 51
status 65
TCP/IP 45 S
monitoring 7
multiplier change 27, 89 save changes 27, 89
serial communication specifications 69
shielded cable 46
O single-phase 8
optional modules software
dimensions 15 FactoryTalk EnergyMetrix 7
P
P option specifications 68
panel cut-out 15

Index
specifications
485 option 69
A option 69
analog output 69
command 70
digital output 68
display 70
energy meters 70
general 72
input 67
isolation between inputs and outputs 73
main functions 71
P option 68
power supply 73
pulse output 68
relay output 68
RS-485 and RS-232 69
serial communication 69
status indicators 70
status 65
status indicators specifications 70
sub-billing 7
T
three-phase 8
V
variables 74 … 75
voltage ranges 8
W
wiring
analog outputs 21
digital outputs 21
Ethernet 23
RS-232 22
RS-485 22
wiring diagrams 17
wiring terminals 16

Index
Notes:

.
Rockwell Automation Support

Use the following resources to access support information.
Technical Support Center Knowledgebase Articles, How-to Videos, FAQs, Chat, User https://rockwellautomation.custhelp.com/
Forums, and Product Notification Updates.
Local Technical Support Phone Numbers Locate the phone number for your country. http://www.rockwellautomation.com/global/support/get-support-now.page
Find the Direct Dial Code for your product. Use the code to
Direct Dial Codes route your call directly to a technical support engineer. http://www.rockwellautomation.com/global/support/direct-dial.page
Installation Instructions, Manuals, Brochures, and

Literature Library http://www.rockwellautomation.com/global/literature-library/overview.page
Technical Data.
Product Compatibility and Download Get help determining how products interact, check
http://www.rockwellautomation.com/global/support/pcdc.page
Center (PCDC) features and capabilities, and find associated firmware.
Documentation Feedback
Your comments will help us serve your documentation needs better. If you have any suggestions on how to improve this document, complete the
How Are We Doing? form at http://literature.rockwellautomation.com/idc/groups/literature/documents/du/ra-du002_-en-e.pdf.
Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.
Allen-Bradley, CompactLogix, ControlLogix, FactoryTalk EnergyMetrix, PowerMonitor, Rockwell Automation, Rockwell Software, RSLinx, RSLogix, RSNetWorx, and Studio 5000 Logix Designer are trademarks of
Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş., Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400
Publication 1420-UM001F-EN-P - January 2017 PN-XXXXXX-XX

Supersedes Publication 1420-UM001E-EN-P - March 2016 Copyright © 2017 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.

PM500

Uploaded by

Copyright:

Available Formats

PM500

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PM500

Uploaded by

Copyright:

Available Formats

User Manual

PowerMonitor 500 Unit

Labels may also be on or inside the equipment to provide specific precautions.

Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 3

4 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

Catalog Number Explanation

1420 -V1 P -485

Bulletin Number Voltage Auxiliary Optional Comms

Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 5

2. Select your product and firmware revision and click Downloads.

3. Click the download icon to access product release notes.

You can view or download publications at

6 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

PowerMonitor 500 Unit Overview

Equipped with an optional communication port, the unit communicates

Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 7

8 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

Front Panel Indicators and Control Buttons

Figure 1 - Front Panel

Display Item Description

Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 9

Additional Button Functions

Displays PowerMonitor 500 information screens, which provide reference

10 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

Display Features Figure 2 - Features

Display Item Description

• Indicates a high value alarm

• Indicates a low value alarm

Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 11

Selected data for Row 1 remains displayed until is pressed.

Table 1 - Row 1 Data

Use and to cycle through the max, instantaneous, and

Table 2 - Rows 2…5 Data

12 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

then press and to select information items, as shown in

Table 3 - Rows 1…5 Information Pages

Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 13

Figure 3 - Information Page 2

Figure 4 - Information Page 15

14 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

Installation and Wiring

Figure 5 - Base Unit Dimensions

Figure 6 - Panel Cut-out

Figure 7 - Factory-installed Optional Modules

Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 15

Figure 8 - Installation in Panel

Figure 9 - Rear View of Unit Showing Wiring Terminals

16 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

Figure 10 - Wiring Diagram Interpretation

Rockwell Automation Publication 1420-UM001F-EN-P - January 2017 17

IMPORTANT In these diagrams, ‘balanced load’ configurations permit 3-phase

Figure 11 - 3-phase, 2-wire Wye, Balanced Load

Figure 12 - 3-phase, 4-wire Wye, Unbalanced Load

Shorting Shorting Ground

Load Ground Load Ground

3-CT Connection 3-CT and3-PT/VT Connections

18 Rockwell Automation Publication 1420-UM001F-EN-P - January 2017

Figure 13 - 3-phase, 3-wire Delta, Unbalanced Load

Load Ground Load Ground

3-CT Connection 3-CT and2-PT/VT Connections (Open Delta)