DCM750 IPTV Gateway

User Manual

Dibsys Technologies (HangZhou) Co., Ltd.

Add:2-2F,102# Xueyuan Road, West Lake District, Hangzhou City, China,postcode:310012 Site: www.dibvision.com
Tel: 086-571-89714580 Fax: 086-571-89714580 Email:sales@dibvision.com
 DIRECTORY

CHAPTER 1 PRODUCT OUTLINE.......................................................................................... 1

1.1 Outline..................................................................................................................................................................... 1

1.2 Features....................................................................................................................................................................1

1.3 IP Protocol Conversion...........................................................................................................................................2

1.4 General Principle Chart.........................................................................................................................................2

1.5 Specifications...........................................................................................................................................................2

1.6 Appearance and Description..................................................................................................................................3

CHAPTER 2 INSTALLATION GUIDE..................................................................................... 4

2.1 Acquisition Check................................................................................................................................................... 4

2.2 Installation Preparation......................................................................................................................................... 4

2.3 Wire’s Connection...................................................................................................................................................6

CHAPTER 3 WEB NMS OPERATION..................................................................................... 7

3.1 login.......................................................................................................................................................................... 7

3.2 Operation.................................................................................................................................................................8

CHAPTER 4 TROUBLESHOOTING......................................................................................17
 DCM750 IPTV Gateway User’s Manual

Chapter 1 Product Outline

1.1 Outline

DCM750 is a powerful, yet low power consumption, rack-mount IPTV Gateway Controller&
Control Interface for 24/7 operation. Its modular design enables integrators and operators to
select from various protocol to customise operation and on-going service.

It can convert the broadcast network IP stream over HTTP, UDP, RTP, RTSP and HLS and TS
file into HTTP, UDP, HLS and RTMP protocol. The platform can achieve the integration by
receiving a variety of commercial streaming media services, and can provide streaming media
services directly.

Designed for the centralised control of Android STB’s the control protocol conversion function
acts, used for the protocol conversion scenarios and streaming media distribution scenarios, to
the commonly deployed STB’s in the hotel, hospitality, corporate, education and entertainment
sectors.

1.2 Features

 low power consumption, rack-mount design

 8 Data ports:
First Data port: IP out over HTTP, UDP (SPTS), HLS and RTMP
Data CH1~CH7 ports: IP in over HTTP, UDP (SPTS), RTP (SPTS), RTSP and HLS
IP out over HTTP, HLS and RTMP (Unicast)
 TS files uploading through Web management
 IP anti- jitter function
 adding scrolling caption, welcome words, boot image and boot video
 Support downloading Dibsys IPTV APK directly from this device
 Up to 80 HD/SD programs (Bitrate: 2Mbps) When HTTP/RTP/RTSP/HLS is converted into
UDP (Multicast)
 Support program playing with APK downloaded android STB and TV, maximum 150
terminals
 Control via web-based NMS management through DATA port

1
 DCM750 IPTV Gateway User’s Manual

1.3 IP Protocol Conversion

1.4 General Principle Chart

1.5 Specifications

IP input thru CH 1-7(1000M) over HTTP, UDP(SPTS), RTP(SPTS), RTSP (over

Input UDP, payload: mpeg TS) and HLS
TS files uploading through Web management
IP out thru Data port (1000M) over HTTP (Unicast), UDP(SPTS, Multicast) HLS
IP output and RTMP (Program source should be H.264 and AAC encoding)
IP out thru CH 1-7(1000M) over HTTP, HLS and RTMP (Unicast)
Memory: 4G
Solid-State Disk(SSD): 16G
Channel switching time with dibsys’ STB: HTTP (1-3s), HLS (0.4-0.7s)
System
Support adding scrolling caption, welcome words, boot image and boot video
(this function is only applicable to IP out application and the STB/Android TV
must be installed dibsys IPTV APK)
2
 DCM750 IPTV Gateway User’s Manual

Play programs with APK downloaded android STB and TV, maximum 150
terminals
Support about 80 HD/SD programs (Bitrate: 2Mbps) When
HTTP/RTP/RTSP/HLS is converted into UDP (Multicast), the actual application
shall prevail, and suggest maximum 80% CPU utilization
web-based NMS management thru DATA port
Demission 482mm×324mm×44mm (WxLxH)
General Temperature 0~45℃(operation), -20~80℃(storage)
Power Supply AC 100V±10%, 50/60Hz or AC 220V±10%, 50/60Hz

1.6 Appearance and Description

Front Panel Illustration:

1/2 Reserved ports for future

3 Data port for IP output and Network management
4 CH1~CH7: IP input / Unicast output ports
5 Grounding Pole/ Power Switch and socket
6 VGA port for connecting displayer

3
 DCM750 IPTV Gateway User’s Manual

Chapter 2 Installation Guide

2.1 Acquisition Check

When users open the package of the device, it is necessary to check items according to
packing list. Normally it should include the following items:
 DCM750 IPTV Gateway
 User’s Manual
 Grounding Cable
 Power Cord
If any item is missing or mismatching with the list above, please contact local dealer.

2.2 Installation Preparation

When users install device, please follow the below steps. The details of installation will be
described at the rest part of this chapter. Users can also refer rear panel chart during the
installation.
The main content of this chapter including:
 Checking the possible device missing or damage during the transportation
 Preparing relevant environment for installation
 Installing gateway
 Connecting signal cables

 Connecting communication port (if it is necessary)

2.2.1 Device’s Installation Flow Chart Illustrated as following：

2.2.2 Environment Requirement

4
 DCM750 IPTV Gateway User’s Manual

Item Requirement

When user installs machine frame array in one machine hall, the
Machine Hall Space distance between 2 rows of machine frames should be 1.2~1.5m
and the distance against wall should be no less than 0.8m.

Electric Isolation, Dust Free

Volume resistivity of ground anti-static material:
Machine Hall Floor
1X107~1X1010  ， Grounding current limiting resistance: 1M
(Floor bearing should be greater than 450Kg/㎡)

Environment 5~40℃(sustainable )，0~45℃(short time)，

Temperature installing air-conditioning is recommended

Relative
20%~80% sustainable 10%~90% short time
Temperature

Pressure 86~105KPa

Installing rubber strip for sealing door-gaps and dual level

Door & Window
glasses for window

Wall It can be covered with wallpaper, or brightness less paint.

Fire Protection Fire alarm system and extinguisher

Requiring device power, air-conditioning power and lighting

power are independent to each other. Device power requires AC
Power
power 100V-240V 50/60Hz 2A. Please carefully check before
running.

2.2.3 Grounding Requirement

 All function modules’ good grounding designs are the basis of reliability and stability of
devices. Also, they are the most important guarantee of lightning arresting and
interference rejection. Therefore, the system must follow this rule.
 Coaxial cable’s outer conductor and isolation layer should keep proper electric
conducting with the metal housing of device.
 Grounding conductor must adopt copper conductor in order to reduce high frequency
impedance, and the grounding wire must be as thick and short as possible.
 Users should make sure the 2 ends of grounding wire well electric conducted and be
5
 DCM750 IPTV Gateway User’s Manual

antirust.
 It is prohibited to use any other device as part of grounding electric circuit
 The area of the conduction between grounding wire and device’s frame should be no less
than 25mm2.

2.2.4 Frame Grounding

All the machine frames should be connected with protective copper strip. The grounding wire
should be as short as possible and avoid circling. The area of the conduction between
grounding wire and grounding strip should be no less than 25mm2.

2.2.5 Device Grounding

Connecting the device’s grounding rod to frame’s grounding pole with copper wire.

2.3 Wire’s Connection

The grounding wire conductive screw is located at the right end of rear panel, and the power
switch, fuse, power supply socket is just beside ,whose order goes like this, power switch is
on the left ,power supply socket is on the right and the fuse is just between them.
 Connecting Power Cord
User can insert one end into power supply socket, while insert the other end to AC power.
 Connecting Grounding Wire
When the device solely connects to protective ground, it should adopt independent way,
say, share the same ground with other devices. When the device adopts united way, the
grounding resistance should be smaller than 1Ω.

Caution:

Before connecting power cord to DCM750 IPTV Gateway, user should set the power
switch to “OFF”.

6
 DCM750 IPTV Gateway User’s Manual

Chapter 3 WEB NMS operation

User can only control and set the configuration in computer by connecting the device to web
NMS Port. User should ensure that the computer’s IP address is different from the DCM750’s
IP address; otherwise, it would cause IP conflict.

3.1 login

The default IP of this device is 192.168.200.136:3333 (3333 is IP port number which can’t be
changed)
Connect the PC (Personal Computer) and the device with net cable, and use ping command to
confirm they are on the same network segment.
I.G. the PC IP address is 192.168.200.136, we then change the device IP to 192.168.200.xxx
(xxx can be 0 to 255 except 136 to avoid IP conflict).
Use web browser to connect the device with PC by inputting this device’s IP address in the
browser’s address bar and press Enter.
It displays the Login interface as Figure-1. Input the Username and Password (Both the
default Username and Password are “admin”.) and then click “Login” to start the device
setting.

Figure-1

7
 DCM750 IPTV Gateway User’s Manual

3.2 Operation

System Chart
When we confirm the login, it displays the status interface where users can have an overview
of system chart. (Figure-2)

User can click any

item here to enter Schematic diagram of
the corresponding system connection
interface to check
information or set
the parameters.

Figure-2

Streaming Media→ NIC Management

From the menu on left side of the webpage, clicking “NIC Management”, it displays the
interface where users can set the dialing and NIC parameters. (If users want to use dialing
function, please contact with local operators.) (Figure-3)

8
 DCM750 IPTV Gateway User’s Manual

Number 1-8 refers to 8

data ports. Number 1
refers to the output data
port. So users can’t set
dialing parameters.

Figure-3

Streaming Media→ Custom Program

Clicking “Custom Program”, it displays the interface where users can upload TS files from
local sources for distributing programs. (Figure-4)

Figure-4

Streaming Media→ Protocol Conversion

Clicking “Protocol Conversion”, it displays the interface where users can set protocol
conversion parameters and add programs from CH1-7. Input protocol supports HLS, HTTP,
RTP, UDP, RTSP (RTP over UDP, playload MPEGTS). Output supports HLS, UDP, RTMP
(RTMP is only supported when input sources are H.264 and AAC encoding.) Output address
9
 DCM750 IPTV Gateway User’s Manual

can’t be changed when selecting HLS as output protocol. (Figure-5)

Click here to select

the programs

Figure-5

: Click to edit or delect programs

: Click to start/stop/stop all the program distribution

: Click box in front of program number, and then click it to batch programs information as

below box. “Keep” means keep the original program information

: Click to download the template for inputting program

information and to batch import/export programs

: Click to add programs and edit program information as below box

10
 DCM750 IPTV Gateway User’s Manual

: Click to batch delete programs

: Click to sort programs manually by dragging program’s name

Streaming Media→ HTTP

Clicking “HTTP”, it displays the interface where users can set the HTTP parameters. HLS,
HTTP and RTSP can’t be converted into HTTP directly, but UDP and RTP can be converted
into HTTP. The setting principle is same as “Protocol Conversion”. (Figure-6)
Note: If users want to IP out over HTTP, they need to convert HLS/HTTP/RTSP into
UDP/RTP, and then converting UDP/RTP into HTTP.

11
 DCM750 IPTV Gateway User’s Manual

Figure-6

ADV→ Rolling Subtitles

ADV function is only applicable to IP out application and the STB and TV must be installed
dibsys IPTV APK.
Clicking “Rolling Subtitles”, it displays the interface where users can add rolling subtitles and
set subtitles’ parameters. After submitting, rolling subtitles will appear when playing
programs. (Figure-7)

Input contents

Figure-7

ADV→ Boot Images

Clicking “Boot Images”, it displays the interface where users can add boot images. Click
12
 DCM750 IPTV Gateway User’s Manual

“Add” and then upload it. After submitting, boot images will appear when starting dibsys
IPTV APK. (Figure-8)

Figure-8

More Configuration→ System Set

Clicking “System Set”, it displays the interface where users can select client protocol and
Unicast output port, and set ADV parameters. (Figure-9)
Receiving programs from “Protocol

conversion” or “HTTP”

“eth0” refers to Data port. “eth1-7”

refer to CH1~7. Users can choose

Unicast output port. IP out over

“Boot Live” refers to access live HTTP/HLS/RTMP through “eth0-7”,
screen with no images and videos. while UDP through “eth0”.
“Boot Video” & “Boot Images” refer

to start APK with video or images.

Selecting “Enable”, inputting welcome words and

it will appear when starting dibsys IPTV AKP.

Figure-9
Select boot setting as “Boot Video” to upload boot video here and it will appear when
starting dibsys IPTV APK. Suggest the size of video file doesn’t over 500M.

13
 DCM750 IPTV Gateway User’s Manual

More Configuration→ Streaming Media Setting

Clicking “Streaming Media Setting”, it displays the interface where users can set streaming
media parameters. (Figure-10)

Figure-10

More→ Client Management

Clicking “Client Management”, it displays the interface where users can download APK
from this device and then upload it to STB and TV. (Figure-11)

14
 DCM750 IPTV Gateway User’s Manual

Figure-11

Clicking “Download APK”, it will trigger a box as below (select saving pass) to save IPTV
APK flie.

More→ AUZ Information

Clicking “AUZ Information”, it displays the interface where users can check the
authorization information. (Figure-12)

15
 DCM750 IPTV Gateway User’s Manual

Figure-12

System Information
Clicking “System Information”, it displays the interface where users can check the system
information such as CPU usage rate, CPU usage record and so on. (Figure-13)

Figure-13

16
 DCM750 IPTV Gateway User’s Manual

Chapter 4 Troubleshooting

dibsys’s ISO9001 quality assurance system has been approved by CQC organization. For
guarantee the products’ quality, reliability and stability. All dibsys products have been passed
the testing and inspection before ship out factory. The testing and inspection scheme already
covers all the Optical, Electronic and Mechanical criteria which have been published by
dibsys. To prevent potential hazard, please strictly follow the operation conditions.

Prevention Measure

 Installing the device at the place in which environment temperature between 0 to 45 °C

 Making sure good ventilation for the heat-sink on the rear panel and other heat-sink bores
if necessary
 Checking the input AC within the power supply working range and the connection is
correct before switching on device
 Checking the RF output level varies within tolerant range if it is necessary
 Checking all signal cables have been properly connected
 Frequently switching on/off device is prohibited; the interval between every switching
on/off must greater than 10 seconds.

Conditions need to unplug power cord

 Power cord or socket damaged.

 Any liquid flowed into device.
 Any stuff causes circuit short
 Device in damp environment
 Device was suffered from physical damage
 Longtime idle.
 After switching on and restoring to factory setting, device still cannot work properly.
 Maintenance needed

17
 DCM750 IPTV Gateway User’s Manual

HangZhou Dibsys Technologies Co., Ltd

Address: Add:2-2F,102# Xueyuan Road, West Lake District, Hangzhou City, China postcode:310012
Tel: +86-571-89714580
Fax: +86-571-89714580
Technical Support Email: service@dibvision.com
Website: www.Dibvision.com

18