Panasonic Kx-Tda100bx Hybrid Ip-Pbx

ORDER NO.
KMS0304726C3
Hybrid IP-PBX
KX-TDA100BX
(for Asia, Middle Near East, South America and Africa)
IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERING

If lead free solder was used in the manufacture of this product the printed circuit boards will be marked PbF.
Standard leaded, (Pb), solder can be used as usual on boards without the PbF mark.
When this mark does appear please read and follow the special instructions described in this manual on the use of PbF and how
it might be permissible to use Pb solder during service and repair work.
© 2003 Panasonic Communications Co., Ltd. All

rights reserved. Unauthorized copying and
distribution is a violation of law.
KX-TDA100BX
CONTENTS
Page Page
1 ABOUT LEAD FREE SOLDER (PbF: Pb free) 3 11.1. INTRUDUCTION 31
1.1. SUGGESTED PbF SOLDER 3 11.2. TYPICAL EXAMPLE 32
1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS 11.3. MPR CARD 33
USED 4 11.4. ERROR LOG 50
2 FOR SERVICE TECHNICIANS 4 12 DIAGNOSIS 55
3 CAUTION 5 12.1. DIAGNOSIS FEATURES 55
3.1. NOTE 5 12.2. DIAGNOSIS TEST 59
3.2. SAFETY PRECAUTIONS 5 13 IC DATA 64
3.3. INSULATION RESISTANCE TEST 5 13.1. IC101 64
3.4. BATTERY CAUTION 5 14 TERMINAL GUIDE OF ICS, TRANSISTORS AND DIODES 68
3.5. CAUTION 5 15 HOW TO REPLACE A FLAT PACKAGE IC 69
4 SPECIFICATIONS 6 15.1. PREPARATION 69
4.1. GENERAL DESCRIPTION 6 15.2. PROCEDURE 69
4.2. CHARACTERISTICS 6 15.3. REMOVING SOLDER FROM BETWEEN PINS 69
4.3. SYSTEM CAPACITY 7 16 CABINET AND ELECTRICAL PARTS LOCATION 70
5 SYSTEM OVERVIEW 8 16.1. EXTENSION BOARDS FOR SERVICING 71
5.1. SYSTEM CONFIGURATIONS 8 17 ACCESSORIES AND PACKING MATERIALS 72
5.2. SYSTEM COMPONENTS 9 18 REPLACEMENT PARTS LIST 73
5.3. SYSTEM CONNECTION DIAGRAM 10 18.1. CABINET AND ELECTRICAL PARTS 73
6 NAME AND LOCATIONS 12 18.2. ACCESSORIES AND PACKING MATERIALS 73
7 DISASSEMBLY INSTRUCTIONS 13 18.3. MPR CARD PARTS 74
7.1. DISASSEMBLY INSTRUCTION (MPR CARD) 13 18.4. BACK/LED BOARD PARTS 79
7.2. DISASSEMBLY INSTRUCTION (BACK BOARD) 14 18.5. FIXTURES AND TOOLS 80
8 OUTLINE 16 19 FOR THE SCHEMATIC DIAGRAM 81
8.1. GENERAL DESCRIPTION 16 20 SCHEMATIC DIAGRAM 82
8.2. SYSTEM CONTROL 17 20.1. MPR CARD 82
8.3. BACK BOARD SIGNAL CONNECTION DIAGRAM 20 20.2. BACK/LED BOARD 87
9 MPR CARD CIRCUIT OPERATION 23 20.3. WAVEFORM 90
9.1. MPR CARD 23 21 PRINTED CIRCUIT BOARD 92
10 BACK BOARD CIRCUIT OPERATION 30 21.1. MPR CARD 92
11 TROUBLESHOOTING GUIDE 31 21.2. BACK/LED BOARD 94
2
KX-TDA100BX
1 ABOUT LEAD FREE SOLDER (PbF: Pb free)

Note:
In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that
contains lead.
We will use PbF when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn), Silver,
(Ag), and Copper, (Cu).
This model, and others like it, manufactured using lead free solder will have PbF stamped on the PCB. For service and repair
work we suggest using the same type of solder although, with some precautions, standard Pb solder can also be used.
Caution
· PbF solder has a melting point that is 50° ~ 70° F, (30° ~ 40°C) higher than Pb solder. Please use a soldering iron with
temperature control and adjust it to 700° ± 20° F, (370° ± 10°C). In case of using high temperature soldering iron, please
be careful not to heat too long.
· PbF solder will tend to splash if it is heated much higher than its melting point, approximately 1100°F, (600°C).
· If you must use Pb solder on a PCB manufactured using PbF solder, remove as much of the original PbF solder as possible
and be sure that any remaining is melted prior to applying the Pb solder.
· When applying PbF solder to double layered boards, please check the component side for excess which may flow onto the
opposite side (See figure, below).
1.1. SUGGESTED PbF SOLDER

There are several types of PbF solder available commercially. While this product is manufactured using Tin, Silver, and Copper,
(Sn+Ag+Cu), you can also use Tin and Copper, (Sn+Cu), or Tin, Zinc, and Bismuth, (Sn+Zn+Bi). Please check the manufac
turer’s specific instructions for the melting points of their products and any precautions for using their product with other
materials.
The following lead free (PbF) solder wire sizes are recommended for service of this product: 0.3mm, 0.6mm and 1.0mm.
3
KX-TDA100BX
1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS USED

Marked PbF (PbF is marked around here)
(Component View)
R251R240 C218
PSUP1317ZB RA308
RA202 24
J113 X202 R247
R248
48
25
48
25
QA103
BATALM C217
R243
13
29 1 D407
LED103
25 C213 36
12
R176 IC205 CN206
IC303
IC304
R164 R239
30 2
C408
R242
LED101
R148
1
QA101
R244
SDIN
37
48
R241
44
1
24
24
1
1
SG
14 IC311 8
L401
R307
9 1
1
IC302
PbF
CN211
7
R218 L210
L208 R233
L207
L206 R231
L205
L204 R229
RA309
C212
J314
R220
22
23
C402
R209 R232 R230
16 IC310 9 IC1
1
44
FIL205
FIL204
1
8 12
SG
R306
8
C208
1
R211
RES
R550
14
14
11
10
R10
R10
R12
R12
R12
IC1
R216
IC
16
1
16
1
Marked PbF (PbF is marked around here)

(Component View)
B1
B45
A45
A1
CN107
B1
R313 R306
B45
R311 R303
C203 R307 C209 R347
C204 R308
R317 R314 R302 C210 R344
R305
R318 R342 R316 R348 R343
R312 R340
R310 R315 R304 C201 R345 R346 PbF
A45
C202 R309 R301 C207 C208
A1
CN112
L105 L112 L108 L101 R338 R335 B1

B45
R333 R334 R326

R330 R329 R323 C205
1
L104 L106 L110 L111 9 L107 L103
L109 L102 R332
C206 R337 R331 R325 R324
R336 R328 R327
PSUP1367Z-A
1
B
CN113
B
RUN
CN114 3 1 3
LED201
LED202
ALM
CN201
PSUP1367Z-B
2 FOR SERVICE TECHNICIANS

ICs and LSIs are vulnerable to static electricity.
When repairing, the following precautions will help prevent recurring malfunctions.
1. Cover the plastic parts boxes with aluminum foil.
2. Ground the soldering irons.
3. Use a conductive mat on the worktable.
4. Do not touch IC or LSI pins with bare fingers.
4
KX-TDA100BX
3 CAUTION
3.1. NOTE
When you note the serial number, write down all of the 11 digits.
The serial number may be found on the label affixed to the bottom of the unit.
3.2. SAFETY PRECAUTIONS

1. Before servicing, unplug the power cord to prevent an electric shock.
2. When replacing parts, use only the manufacturer´s recommended components for safety.
3. Check the condition of the power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, be sure to perform the following insulation resistance test to prevent
the customer from being exposed to shock hazards.
3.3. INSULATION RESISTANCE TEST

1. Unplug the power cord and short the two prongs of the plug with a jumper wire.
2. Turn on the power switch.
3. Measure the resistance value with ohmmeter between the jumpered AC plug and each exposed metal cabinet part, such as
screw threads, control shafts, handle brackets, etc.
Note:
Some exposed parts may be isolated from the chassis by design. These will read infinity.
4. If the measurement is outside the specified limits, there is a possibility of shock hazard. The equipment should be repaired and
rechecked before it is returned to the customer.
3.4. BATTERY CAUTION

1. Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the
manufacturer. Dispose of used batteries according to the manufacturer’s Instructions.
2. The lithium battery is a critical component (type No.CR23541). Please observe for the proper polarity and the exact location
when replacing it and soldering the replacement lithium battery in.
3.5. CAUTION
The power socket wall outlet should be located near this equipment and be easily accessible.
5
KX-TDA100BX
4 SPECIFICATIONS
4.1. GENERAL DESCRIPTION
Control Bus Original bus (16 bit, 8 MHz,10 megabytes per second)
Communication Bus H.100 bus conformity (1024 time slot)
Switching Non Blocking Distributed Time Switch
Power Input PSU-S 100 V AC to 130 V AC/200 V AC to 240 V AC, 1.4 A/0.8 A, 50 Hz/60 Hz
(KX-TDA0108)
PSU-M 100 V AC to 130 V AC/200 V AC to 240 V AC, 2.5 A/1.4 A, 50 Hz/60 Hz
(KX-TDA0104)
External Battery +36 V DC (+12 V DC x 3, battery capacity of 28 Ah or below recommended for 1 external
battery)
Maximum Power Failure Tolerance 300 ms (without using backup battery)
Memory Backup Duration 7 years
Dialling Trunk Dial Pulse (DP) 10 pps, 20 pps
Tone (DTMF) Dialling
Extension Dial Pulse (DP) 10 pps, 20 pps
Tone (DTMF) Dialling
Mode Conversion DP-DTMF, DTMF-DP
Ring Frequency 20 Hz/25 Hz (selectable)
Trunk Loop Limit 1600 Ω maximum
Operating Temperature 0 °C to 40 °C
Environment Humidity 10%to 90% (non condensing)
Conference Call Trunk From 10 x 3-party conference call to 4 x 8-party conference call
Music on Hold (MOH) 2 ports (Level Control: -11 dB to +11 dB in 1 dB steps)
MOH1: External Music Source port
MOH2: Selectable Internal/External Music Source port
Paging Internal Level Control: -6 dB to +3 dB in 3 dB steps
External 2 ports (Volume Control: -15 dB to +15 dB in 1 dB steps)
Serial Interface Port RS-232C 1 (max 115.2 kbps)
USB 1
Extension Connection Cable SLT 1 pair wire (T, R)
DPT 1-pair wire (D1, D2) or
2-pair wire (T, R, D1, D2)
APT 2-pair wire (T, R, D1, D2)
DSS Consoles and Add-on Key Module 1-pair wire (D1, D2)
Dimension KX-TDA100 334 mm (W) x 390 mm (H) x 270 mm (D)
(13 5/32 in x 15 11/32 in x 10 5/8 in)
Weight (when fully mounted) KX-TDA100 Under 12 kg (26.5 lb)
4.2. CHARACTERISTICS
Terminal Equipment Loop Limit · PT: KX-T76xx series and KX-T7560/KX-T7565: 90 Ω; all other DPTs/APTs: 40 Ω
· SLT: 600 Ω including set
· Doorphone: 20 Ω
· CS: 130 Ω
Minimum Leakage Resistance 15000 Ω maximum
Maximum Number of Extension 1 for PT or SLT
Instruments per Line 2 by Parallel or eXtra Device Port connection of a PT and an SLT
Ring Voltage 75 Vrms at 20 Hz/25 Hz depending on the Ringing Load
Trunk Loop Limit 1600 Ω maximum
Hookswitch Flash/Recall Timing Range 24 ms to 2032 ms
BRI Cards Internal ISDN Mode Supply Voltage: 40 V
Power Supply: 4.5 W per 1 line,10 W per 4 lines (BRI4)
4.5 W per 1 line, 20 W per 8 lines (BRI8)
Power Supply Method: Phantom Power Supply
Door Opener Current Limit 24 V DC/30 V AC, 1 A maximum
Paging Terminal Impedance 600 Ω
MOH (Music on Hold) Terminal Impedance 10000 Ω
6
KX-TDA100BX
4.3. SYSTEM CAPACITY

4.3.1. Maximum Trunk and Extension Cards
The following number of trunk and extension cards can be installed in the main unit (Hybrid IP-PBX) for expansion.
Card Type KX-TDA100
Trunk Card *1 4
Extension Card 4
Total 5
*1 One T1, E1, PRI30 and PRI23 card counts as 2 cards.

Note:
· For each card, a maximum number that can be installed in the main unit (Hybrid IP-PBX) is listed in "Installation Manual".
· Any card that exceeds the capacity of the main unit (Hybrid IP-PBX) will be ignored.
· When the main unit (Hybrid IP-PBX) starts up with an invalid configuration mode, some cards will be ignored.
4.3.2. Maximum Terminal Equipment

The following number of terminal equipment can be supported by the main unit (Hybrid IP-PBX).
Terminal Equipment Type KX-TDA100
Telephone *1 64
CS 16
PS 128
Voice Mail 2
Doorphone 8
Door Opener 8
*1 When only T76xx series and T7560, T7565 DPTs and SLTs are connected. If other DPTs or APTs are connected, the
maximum number will decrease as each of these units is counted as 4 sets of SLTs or DPTs (T76xx series and T7560, T7565).
4.3.3. Power Supply Unit Selection

Main unit (Hybrid IP-PBX) needs an optional power supply unit (PSU) suitable for its configuration. Calculate the amount of
"load figures" from the type and number of equipment to be connected, and determine the type of PSU that will be required.
Load Figure Calculation

Equipment Type Load Figure
PT DPT (T76xx series and T7560, T7565) 1
Other DPT/APT/DSS Console 4
Extension Card *1 DHLC8 8
SLC8 8
SLC16 16
MSLC16 16
CS 4
ISDN Extension 2
Voice Mail 1
*1 Only the extension cards that can support SLTs count for the load figures.
PSU Capability
Each PSU supports a different amount of load figures.
PSU Type Maximum Load Figures
PSU-S 64
PSU-M *2 128
*2 Available for the KX-TDA100 and KX-TDA200.
7
KX-TDA100BX
5 SYSTEM OVERVIEW
5.1. SYSTEM CONFIGURATIONS
8
KX-TDA100BX
5.2. SYSTEM COMPONENTS

Model Card Name Description
Shelf KX-TDA100BX Basic Shelf
Main Central Processing MPR Main Processing Card
Card
MPR Option Card KX-TDA0196XJ RMT Remote Card
CO Line Cards KX-TDA0180X LCOT8 8-Port Analogue Trunk Card
KX-TDA0181X LCOT16 16-Port Analogue Trunk Card
KX-TDA0184XJ E&M8 8-Port E &M Trunk Card
KX-TDA0188XJ E1 E-1 Trunk Card
KX-TDA0193XJ CID8 8-Port Caller ID Card
KX-TDA0284XJ BRI4 4-Port BRI Card
KX-TDA0288XJ BRI8 8-Port BRI Card
KX-TDA0290CJ PRI30 PRI Card
KX-TDA0290X PRI23 PRI Card
KX-TDA0480X IP-GW4 4-Channel VoIP Gateway Card
Extension Cards KX-TDA0144XJ CSIF8 8 Cell Station Interface Card
KX-TDA0170XJ DHLC8 8-Port Digital Hybrid Extension Card
KX-TDA0171XJ DLC8 8-Port Digital Extension Card
KX-TDA0172XJ DLC16 16-Port Digital Extension Card
KX-TDA0173XJ SLC8 8-Port Single Line Telephone Extension Card
KX-TDA0174XJ SLC16 16-Port Single Line Telephone Extension Card
KX-TDA0175XJ MSLC16 16-Port Single Line Telephone Extension with Message Lamp Card
Other Cards KX-TDA0161XJ DHP4 4-Port Doorphone Card
KX-TDA0166XJ ECHO16 16-Channel Echo Canceller Card
KX-TDA0190XJ OPB3 Optional 3-Slot Base Card
KX-TDA0191XJ MSG4 4-Channel Message Card
KX-TDA0410XJ CTI-LINK CTI Link Card
Power Supply Units KX-TDA0104XJ PSU-M M-Type Power Supply Unit
(PSUs) KX-TDA0108XJ PSU-S S-Type Power Supply Unit
Cell Stations (CS’s) KX-TDA0142CE 4-Channel Cell Station Unit for DECT Portable Station
Proprietary Equipment KX-A228XJ S/M-type Back-up Battery Cable
KX-A229XJ L-type Back-up Battery Cable
KX-A258XJ Blank Slot Cover
KX-T30865X Doorphone
Available Telephones
This main unit (Hybrid IP-PBX) supports all of the Panasonic KX-T7xxx and KX-TD7xxx series:
· Digital/Analog proprietary telephones (e.g., KX-T7625, KX-T7630, KX-T7633, KX-T7636)
· Portable stations (e.g., KX-TD7690, KX-TD7680)
· DSS consoles (e.g., KX-T7640)
This main unit (Hybrid IP-PBX) does not support the following telephones:
· KX-T308xx series Proprietary Telephones and DSS consoles
For the equipment (e.g., Add-on Key Module, USB Module, Headset) that can be connected to a particular telephone, refer to
the telephone’s manual.
Abbreviations in this manual

Proprietary telephone: PT
Digital proprietary telephone: DPT
Analog proprietary telephone: APT
Portable station: PS
Single line telephone: SLT
Note:
· There are some optional service cards and features that are not available for certain countries/areas. Consult your
authorized Panasonic dealer for detailed instructions.
· The power supply capacity of this main unit (Hybrid IP-PBX) may differ from the values described in this manual depending
on the model number. Please consult your dealer for detailed information.
9
KX-TDA100BX
5.3. SYSTEM CONNECTION DIAGRAM
10
KX-TDA100BX
*Only 1 Server PC can be connected to the main unit (Hybrid IP-PBX). Two or more Server PCs cannot be used simultaneously.
11
KX-TDA100BX
6 NAME AND LOCATIONS
· Null slot:
Null slot is not available for any optional service card.
LED Type Color Usage and Status Definition
RUN Indicator LED1 Green Display of Power Supply & RUN Status
(Power/RUN) OFF: Power OFF (inc. in normal resetting)
ON: Power ON & RUN (On-Line)
Flash (60/min.): Power ON & In starting
Flash (120/min.): Power ON & In resetting before system clear
ALARM Indicator LED2 Red Display of ALARM
(Alarm) OFF: Normal
ON: Alarm (CPU stop, Alarm for each card)
Flash: Alarm (MPR file error in restarting)
Slot Type MPR Card CO Line Cards OPB3 Card

Extension Cards CTL-LINK Card
Free Slots 1 to 5 No Yes Yes
Option Card Slot No No Yes
MPR Card Slot Yes No No
12
KX-TDA100BX
7 DISASSEMBLY INSTRUCTIONS
7.1. DISASSEMBLY INSTRUCTION (MPR CARD)
1. Remove the Lib by sliding it in the direction of arrow 1.
2. This will be removed if the user attached a Pad Lock as shown in a
Fig.1.
3. Loosen the Screw.
4. Front Cover is removed in the direction of arrow 2.
5. Loosen the two Screws.

6. Remove the MPR Card.
13
KX-TDA100BX
7.2. DISASSEMBLY INSTRUCTION (BACK BOARD)

1. Remove four Screws (A).
2. Remove the Left Side Cover and the Right Side Cover.
3. Remove the Hook. Remove the Top Cover.
4. Remove nine Screws (B).

5. Remove the Back Cover.
14
KX-TDA100BX
6. Remove the RS-232C Connector and LED Connector from Back

Board 1.
7. Remove eight Screws (C).
8. Remove Back Board 1.
9. Remove the LED Connector from Back Board 2.

10. Remove the Screw (C).
11. Remove Back Board 2.
15
KX-TDA100BX
8 OUTLINE
8.1. GENERAL DESCRIPTION
The control system of the main unit is composed of the main central processing card (MPR card) controlling the entire system
and exchanging voice data, the circuit control section (LPR/LC) controlling various telephone lines and the power supply section
(POWER).
MPR card, LPR/LC and POWER are connected each other through the System BUS (ADDRESS BUS, DATA BUS and
CONTROL BUS). MPR card and LPR/LC are under I/O control (I/O Read/Write) by MPR card.
MPR card controls LPR which have a microprocessor by the lnter-Microprocessor Communication System supported by ASIC.
Those are, MPR card and LPR exchange controlling messages through bi-directional buffer and CPU controls LPR so that it
can manage multiple telephone lines. Since LC does not have a microprocessor, it is completely controlled through ASIC from
MPR card.
I/O address for LPR access is fixed for each free slot. CPU discriminates the sort of LPR through the inter-processor
communication system.
POWER detects the voltage drop of the AC input and the DC output and transfers it to MPR card.
8.1.1. MPR Card
This card is the main control section of main unit. It controls all the cards mounted on the free slots, and communication of RS-
232C ports.
There are two LED (BATT ALARM, SD ACCESS), one SD card slot, one push switch, one slide switch, one USB port, two MOH
jacks, and two EPG jacks in the front of MPR card. BATT ALARM LED light red if the output of the lithium battery in MPR card
is set to about 2.8V or less. During access to SD card, it green-blinks or SD ACCESS LED light and blink. Enclosed SD card
is used for SD card slot on a main part, putting in. The main program is stored in SD card. It connects with PC and a USB port
is used for a maintenance or a system setup. The external sound source for BGM or suspension sound is connected to a MOH
jack. A speaker with amplifier is connected to external paging at an EPG jack. Light Emitting Diode (RUN indicator,
ALARMindicator) arranged at the main part upper part is directly controlled from MPR card, and shows the state of a system
of operation.
This control circuit executes the control signals for the exchange process, and this card is composed of the following
(A) 32bit CPU (32bit data bus)
(B) SDRAMs, SRAMs
(C) Flash memorys
(D) Lithium Battery for back-up of clock IC and Static RAMs
8.1.2. Back Board
BB (back board) is the mother board of the basic shelf. This board connects each card/unit (POWER, MPR card, and optional
service cards) together. This board has one RS-232C connector.
8.1.3. Power Supply Unit
This unit is switching regulator power supply and supplies DC voltages to MPR card, and optional card (free slot). PSU (power
supply unit) has four outputs (40V, 30V, 15VPT, 15V). 15V output is supplied only in MPR card and option card. Other outputs
are mainly used as an object for the electric supply to a terminal. Refer to each S/M for the details of PSU.
16
KX-TDA100BX
8.2. SYSTEM CONTROL

8.2.1. System Control Block Diagram
17
KX-TDA100BX
8.2.2. Voice (TDM Highway) Bus Block Diagram
18
KX-TDA100BX
8.2.3. Voice Bus Logical Assignment
In the line card, the CT_D line number, which is output in accordance with the inserted slot, and the time slot are assigned by
software.
For the detail of output slot for each card (optional service card), refer to the service manual of the card (optional service card).
8.2.4. Back Board Signaling
Back board waveform of TDM bus for voice
19
KX-TDA100BX
8.3. BACK BOARD SIGNAL CONNECTION DIAGRAM

8.3.1. CT Bus System Connection Diagram
20
KX-TDA100BX
8.3.2. EC Bus System Connection Diagram
21
KX-TDA100BX
8.3.3. System Control and Analog Signal Connection Diagram
8.3.4. Power Supply System Connection Diagram
22
KX-TDA100BX
9 MPR CARD CIRCUIT OPERATION

9.1. MPR CARD
9.1.1. Outline
1) Function
· System Control
· Circuit Switching (includes gain adjustment function)
· Conference Call (3 people x 8 ~ 8 people x 3)
· MOH
· PAGING
· Clock
2) Configuration
· Power Supply: DC/DC Converter
· CPU: HITACHI SH7709S (133MHz)
· ASIC: Our own products
· ROM: 4Mbit x 1 (for boot programs)
· SDRAM: 64Mbit x 2 (for work area)
· SRAM: 4Mbit x 2 (for user data backup)
· SD card I/F (for operating programs) x 1
· USB I/F (for PC programming) x 1
· MOH: External sound input x 2
· PAGING: External output x 2
· Expanded memory connector x 1
· Modem card connector x 1
3) Operation Rating
· Power Input : +15V
· Power Output : +15V (for MOH)
+3.3V (for I/O)
+3.3VBB (back board signal line pull-up)
+3.3VB (for SRAM backup)
+1.8V (for CPU core)
+1.9VB (for clocking backup)
±9.4V (for RS-232C driver/receiver)
+5VRMT unused (for remote card)
+5V (for RS-232C driver/receiver)
23
KX-TDA100BX
9.1.2. Description of Each Part
LED (BATALM): Lights when the lithium battery voltage drops below 2.8V.
LED (SD ACCES): Lights on when the SD card is being accessed.
SD card slot: Mounts the system program SD card.
Reset Switch: Press to reset the system.
System Initialize Switch:
On default startup, set the switch to the "SYSTEM INITIALIZE" position before turning the power ON. Return the switch to the
"NORMAL" position when the main power switch starts to flash. On normal startup, turn the power ON with this switch in the
"NORMAL" position.
USB connector: B-type connector. Used for PC programming.
MOH 1, 2: External music on hold input.
PAGING 1, 2: External PAGING output. Connect to a device with a built-in amplifier.
24
9.1.3.
IC301, IC302 IC303 IC305, IC306

SD Card Interface MEC Card +15V -9V +9V +5V +3.3V +1.8V
SD Card (MN5773) (Expansion Memory) FLASH
SRAM SDRAM IC403
IC205 (Future option) Total:1MB Total:512KB Total:16 MB
4Mbit*2 4Mbit IC413 IC402 Series Reg.
64Mbit*2
USB Interface (16bit bus) (16bit bus) (32bit bus) Series Reg.
USB OSC SW Reg. SW Reg.
Conn. (ML60852A) 20MHz
IC204 X202
CN209
90pin DIN
OSC
12MHz X201
LD[15:0]
ADD0-7
nCS_SDB
DQMLU,DQMLL
nRD
D[31:0]
LD[15:0]
ADD[25:0]
nCS_2 etc.
RD/nWR
nRAS
nCAS
CKIO
CKE
+3.3VB
LD[15:0]
ADD1-19
nCS_4
RD/nWR
+3.3VB
LD[15:0]
ADD1-23
RD/nWR
nCS_0
D[31:0]
ADD2-15
nCS_3
RD/nWR
nRAS
nCAS
+15V
nRD
nRD
CLK
CKE
ASIC
DQMUU,DQMUL
DQMLU,DQMLL
DQMUU,DQMUL
DQMLU,DQMLL
DATA BUS LD[15:0] D0-D15 DATA GND
IC102
Block Diagram
ADD BUS A1-A23 ADD

+3.3V Current +3.3V_BB
CNT BUS Limitter (for B.B.)
nCS_5
Dbus nCS EC_CLK EC_CLK
Buffer nWR
LED101
nWR EC_nRST EC_nRST
+3.3VB +3.3V nRD
IC123, IC124 nRD EC_AD[15:0] EC_AD[15:0]
SD-ACCESS CS Generation VRTC nBS
A[25:0]
EC_CBE[1:0] EC_CBE[1:0]
D[31:0]
Regulator nBS
for EC_nPAR EC_nPAR
(+1.8V) TCXO EC_bus
BATT ALARM Flash,SRAM, EC_nFRAME EC_nFRAME
SDB, USB IC404 16.384MHz EC_nTRDY EC_nTRDY
LED103 +3.3V nWR, nRD
X103 EC_nSTOP EC_nSTOP
+1.8V nCS0,3,4
Battery EC_nPERR EC_nPERR
nRASs, nCASs,etc
(+3.0V) EC_nCDET Termination EC_nCDET
(Manual Reset SW) nBREQ EC_nINT EC_nINT
Reset nBREQ
to Reset IC Bus Arbiter nBACK (EC_IDSEL)
nBACK
nDREQ0,1 DC_ALM,nIRQ_USB, nIRQ_SDB
SW101 nDACK0,1 DMAC Interrupu
Controller nIRQ nIRQ
VRTC
+3.3V
RTC X102
32.768kHz +3.3V
X101 HALT, Mu/nA,MOH_SEL,
25
nPRS_RMT MELODY_SEL
Initialize CLK OSC PIO[7:4]
to CPU GAIN0,GAIN1
SW Modulation 16.384MHz
SW103 IC103 CoreCLK=131.072MHz DTR,DSR
CPU RMT card TxD,RxD,CTS,RTS(UART i/f) SDI,SDO,CTS,RTS
SH7709S Local (Option) CT_NETREF CT_NETREF
IC101 Reset UHW,DHW,CLK(4.096MHz) LDHW0,LUHW0 CT_D[7:0]
CT_D[7:0] H100_bus
nF0,HW_CLK CT_FRAME
30pin Connection
IC107 Mu/nA CT_FRAME
CT_C8 CT_C8
CH_SEL2 CH_SEL[2:0]
(for RS232C port)
SIO with FIFO(SCI1) IC120 +9V,-9V
+3.3V DRV TXD1, RS1, ER1
IC406 IC405
CH_SEL1
CH_SEL0
SIO with FIFO(SCI2) 7pin Conn. MELODY_SEL RCV RXD1, CS1, DR1
SIO(SCI0) (Debug Interface) (Software) Melody CODEC CODEC IC121 +5V
IC410 IC (+3.3V) (+3.3V) TXD2
JTAG Interface MOH-SEL RXD2
(Checker Pad only) (Software) DCALM
PCMCIA Interface
ACALM
to CPU(Input Port)
POWTYPE[1:0]
DTR,RTS,LEDs,REG,BELTIME
AGC nBATT
P-I/O Ports AGC
+15V/GND nLOS
DSRs,DTRs, RTS, CTS, IC409 IC408
nINIT, DIPSWs from ASIC(Output Port) nHALT
AC_ALM,DC_ALM,nBATALM
POWTYPE[1:0],nBATT from ASIC RINGER
RING_SIN
MOH2
MOH1
Paging2
Paging1
RING_SYNC
from CPU(Output Port) LEDRUN
LEDALM
MPR Card
KX-TDA100 MPR CARD BLOCK DIAGRAM
KX-TDA100BX
KX-TDA100BX
9.1.4. Circuit Description

9.1.4.1. Outline of Block Description
· CPU block
Operates the main unit control. Also operates various controls, generation of select signal, DMA control and serial port control.
This contains the built-in clock function.
· ASIC block
Provides the communication between each optional service card, call control (TSW function), conference call, tone generation
and gain control function.
· Memory block
This is a work area used for the main unit control program storage, the system boot program storage, or the user configuration
data storage.
· USB block
Provides the USB I/F function. Connects to the PC to be used for PC programming or system data load/store.
· SD card block
Provides the SD card I/F function and loads the main unit program and the system data from the SD card containing the main
unit control program.
· MOH/PAGING block
Provides the external music on hold input x 2, and the external paging output x 2 port. Also this provides the external music on
hold input 1 system and exclusively the internal music on hold output.
· Power block
Consists of DC/DC converter circuit and various regulators.
9.1.4.2. Detail of Block Description

· CPU block
Configuration: IC101 (CPU), IC107 (reset IC), IC103 (spread clock IC), X101 (CPU source clock), X102 (clocking clock) etc.
Function: (IC101)
Generates the select signal in accordance with the memory map and operates read/write of data between each peripheral.
Controls the DMA transfer between USB I/F or built-in serial controller and memory.
Operates input/output control of each I/O signal in accordance with the program.
Contains the built-in clock function (battery backup) with the source clock X102 (32.768 kHz).
(IC107)
Monitoring the power voltage, it generates a reset signal when the voltage drops under the constant value (2.9Vtyp) or when
the reset switch is pressed down.
(IC103)
To reduce unnecessary radiation, it generates the clock with the constant blurring mainly X101 clock output (16.384 MHz).
Description of the Signal on MPR
Signal Name Functions
+15VIN +15V DC
+15V For Circuit +15V DC MOH
+9.4V For Driver IC +9.4V DC RS-232C
+5V For Driver IC +5V DC RS-232C
+5VRMT Reserve
3.3V_BB +3.3V DC
For pull-up of back board signal line
+3.3VB +3.3V DC
Battery backup
For SRAM (IC301, IC302) backup
+3.3V +3.3V DC
1.9VB +1.9V DC
Battery backup
For clock function of CPU (IC100)
1.8V For Core +1.8V DC CPU (IC100)
A[0]-A[25] Address bus
nAC_ALM AC alarm signal: Indicates AC voltage cutoff. (L: Alarm condition)
nBACK Bus Acknowledge: Indicates Bus Acknowledge.
nBATT Indicates whether external battery is connected or not. L: Connected
26
KX-TDA100BX

nBAT_ALM Battery Alarm Signal: Indicates the declined voltage of lithium battery. (L: Alarm condition)
nBREQ Bus Request: Bus request signal
nBS Bus Cycle Start: Bus cycle start signal
nCASL Lower Byte Address Column Address Strobe: CAS signal for SDRAM
nCASU Upper Byte Address Column Address Strobe: CAS signal for SDRAM
CH_SEL[0] Synchronous Signal for CODEC (For MOH#1/Page#1)
CH_SEL[1] Synchronous Signal for CODEC (For MOH#2/Page#2)
CH_SEL[2] Synchronous Signal for CODEC (For RMT)
CKE Clock Enable: CKE signal for SDRAM
CKIO Clock I/O Terminal: For bus clock of SDRAM (IC305, IC306) and ASIC (IC101) CPU (IC100) outputs the clock of four
times frequency as Source clock (16.384MHz).
nCS0 Chip Select 0: Chip select signal for flash memory
nCS2 Chip Select 2: Chip select signal for the expanded SDRAM (Future Option, Reserve at present.)
nCS3 Chip Select 3: Chip select signal for SDRAM
nCS4 Chip Select 4: Chip select signal for SRAM
nCS5 Chip Select 5: Chip select signal for ASIC
nCS6 Chip Select 6: Chip select signal for USB I/F and SD card I/F
nCS_FLASH0 Chip Select for Flash memory 0: CS signal for IC303
nCS_FLASH1 Chip Select for Flash memory 1: CS signal for IC304 (reserve)
nCS_SDB0 Chip Select for Sd card I/F
nCS_SDB1 Reserve
nCS_SRAM0 Chip Select for SRAM 0: CS signal for IC301
nCS_SRAM1 Chip Select for SRAM 1: CS signal for IC302
nCS_USB Chip Select for USB I/F
nCTS2 Clear To Send from RS-232C connector
CTS_RMT Clear to Send: Flow signal for modem
CT_C8 Clock 8.192MHz clock outputted from PLL master
CT_D[0] -[7] CT Data Bus: Two-way serial data bus to which the drive from any card is possible in the system.
CT_FRAME Frame Signal: 8KHz frame signal outputted from the master
CT_NETREF Backup Synchronous Signal (MAX 2MHz) 8KHz signal output from slave etc.
C_CS[0] Chip Select For RMT
D[0] -D[31] Data Bus
nDACK0-1 DMA Acknowledge: For USB I/F
DCD2 Data Carrier Detect
DCLK_RMT Codec Clock (8MHz): For RMT
nDC_ALM DC ALARM:DC alarm signal; Indicates the declined DC voltage. (L: Alarm condition)
DIN_RMT Codec Data Input: For RMT
DOUT_RMT Codec Data Output: For RMT
DQMLL (nWE0) Data Input/Output Mask (Write Enable): DQM signal for SDRAM and WE signal for each memory IC and ASIC
DQMLU (nWE1)
DQMUL (nWE2)
DQMUU (nWE3)
nDREQ0-1 DMA Request: For USB I/F
DSR2 Data Set Ready from RS-232C connector
DSR_RMT Data Set Ready from RS-232C connector
DTR2 Data Terminal Ready to RS-232C connector
EC_AD[0] -[15] Address of EC Synchronous Bus, Data Bus (4MHz)
EC_nCBE[1]-[0] EC Bus Command/Byte Enable: The initiator drives as bus command in the address phase and as byte enable in the
data phase.
EC_nCDET EC Line Card Detection Signal Asynchronous interrupting signal
EC_CLK Clock of EC Synchronous Bus (8MHz) All EC bus signals except nRESET/EC_INT operates in sync with this signal.
EC_nFRAME EC Cycle Frame Signal: Indicates the drive by initiator and the execution of ECI bus cycle.
EC_nINT EC Interrupting Signal: Be asserted when slave interrupt occurs.
EC_PAR Parity Bit of EC Synchronous Bus: Drive by applying even parity to AD[15:0] and CBE[1:0]. (4MHz)
EC_nPERR EC Parity Error: Flag indicating error status by parity flag
EC_nRST EC Reset Input: System reset input signal
EC_nSTOP EC Bus Stop Signal: Be asserted when target requests transaction halt to initiator.
EC_nTRDY EC Target Ready Signal: Indicates the drive by target and the possible data transfer.
nFAN_ALM Fan Alarm: It goes Low at the error of the L Power Supply’s FAN. It goes High when the FAN is normal and, Power
Supply S and M, which does not carry the FAN, are used.
FSEL0 Signal which switches the Flash Memory address of the MEX card. FSEL0 is set by hard jumper. L: The number of
Flash Memory chips on the MPR is 1pc. H: The number is 2pcs.
GAIN0-1 Gain: Gain adjustment signal for the RMT card (Reserve)
HALT Alerts the occurrence of the declined DC voltage to line card. H: Active L: Normal
nINIT System Initialization Switch Input: L: At system initialization, H: At normal start-up
nIRQ_ASIC Interrupt Request from ASIC: Indicates ASIC requests interrupt.
nIRQ_SDB Interrupt Request from SD card I/F: Indicates SD card I/F requests interrupt.
nIRQ_USB Interrupt Request from USB I/F: Indicates USB I/F requests interrupt.
27
KX-TDA100BX

LA[1] -[16] Address bus
nLB Lower Byte Select: Indicates Lower byte select signal of SRAM
LD[0] -[15] Data Bus
LDHW[1] -[0] Down Highway: Data output terminal connected to codec etc. as down data signal of local highway
nLEDALM Alarm display L: On
nLEDRUN RUN display L: On
nLOS Loss of synchronous signal: Reserve at present
LHWCLK[0] Highway Clock Signal (8MHz): Bit clock of local highway and selectable among 2.048 / 4.096 / 8.192MHz.
LUHW[1] -[0] Up Highway: Data input terminal connected to codec etc. as up data signal of local highway.
MASTER/nS Master/slave identification signal when SIC card (Future Option) as intersystem connection card is mounted. MPR
inputs this signal and detects which the MPR will be. H: Master L: Slave
MD0-2 Mode Control Terminal: Clock operation mode of CPU is set.MD2: L, MD1: L, MD0: H Fixed
MELODYSEL Melody IC Tune Name Select L: Ju te veux H: Minuet
MEX_MODE[0] -[3] Information Bit to know the memory mounting capacity etc. of MEX card. Reserve at present.
MOHSEL Switching Signal between internal hold sound source and external hold sound H: Internal L: External
Mu/nA Switching Signal of Sound Compression Law H: Mu-Law, L: A-Law
M/nS TDA100, TDA200 Identification Signal set on the back board. The MPR inputs this signal and detects which the MPR
will be. H: TDA200, L: TDA100
POWTYPE[0] -[1]
nPRS_MEX Press MEX: Information of MEX Card Attachment L: Attached, H: Not attached
nPRS_RMT Press RMT: Information of RMT Card Attachment L: Attached, H: Not attached
nPRS_SDB Press SD card: Information of SD Card Attachment L: Attached, H: Not attached
nRAS3L Lower Byte Address Row Address Strobe: RAS signal for SDRAM
nRAS3U Upper Byte Address Row Address Strobe: RAS signal for SDRAM
nRD Read: USB I/F, SD card I/F, ASIC, SRAM, Read signal for flash memory
RD/nWR Read/nWrite: Read/Write signal for SDRAM
nRESOUT Reset Out: Reset from CPU (IC101) to each card
nRESET Reset: Power-on reset signal
nRESETM Manual Reset: Manual reset request signal for CPU
RINGER Ringer Signal: Outputs square-wave of 16Hz/20Hz/25Hz as source signal of ringer
RING_SYNC Trigger Signal of Ringer Signal generation timing to each internal line card
nRTS2 Request To Send to RS-232C connector
RTS_RMT Request to Send: Flow signal for modem
RXD2 Receive Data from RS-232C connector
RXD_RMT Serial Data Output Terminal: ASIC
SDCD SD Card Detect Input
SDCLK SD Card Clock Out
SDCMD SD Command
SDDAT0-3 SD Card Data
SDWP SD Card Write Protect Input
SHW_CLK Intersystem Highway Clock Signal (4MHz) Bit clock of intersystem highway and selectable between
256KHz/512KHz/1.024MHz/2.048MHz/4.096MHz.
SHW_FH Intersystem Highway Synchronous Signal (8KHz) 8KHz frame synchronous signal of intersystem highway
TXD2 Transmit Data to RS-232C connector
TXD_RMT Serial Data Input Terminal: Data receiving terminal from RMT to UART in the ASIC
nUB Upper Byte Select: SRAM
USB_D+ USB Data +
USB_D- USB Data -
VBUS Bit indicating power source is supplied to USB bus [Host (PC etc.) is connected.] H: Host connected L: Host not
connected
VREF Reference Voltage for MOH Circuit Intermediate potential of +15V
nWAIT Wait: Hardware wait request signal for bus timing between CPU and ASIC
WDTCLR Reserve
nWE Write Enable: WE signal of SRAM
· ASIC block
Configuration: IC102 (ASIC), IC111, X103 and so on.
Function: (IC102)
28
KX-TDA100BX
Functions as the bus master of EC bus (synchronous bus with 16 bit width, transmission rate max.10Mbps). Communicates
with ASIC mounted to each option card via EC bus and controls the option card.
Controls CT bus (HW clock 8.192MHz, 8 highway, 128 timeslot) for TSW function.
(A detailed description of TSW will be added later.)
Controls the conference call for 3 people x ~8 parties ~ 8 people x ~3 parties.
Generates single and DTMF tone in any highway and timeslot.
Provides the digital gain control function by data conversion.
Provides some I/O ports for CODEC channel pulse generation, modem encoding rule setting and music on hold switching
and is controlled by CPU.
· Memory block
Configuration: IC301, IC302 (SRAM), IC303 (FlashROM), IC305, IC306 (SDRAM), IC309, IC310, IC311 (logic IC) and so
on.
Function: (IC301, IC302)
Saves the user configuration data (such as key assign data per PT).
This memory is battery backup.
(IC303)
Saves (some of) the system boot program and the system data.
(IC305, IC306)
The main program is loaded from the SD card on the system start-up.
Used as the program area and the CPU work area after start-up.
Makes a direct bus connection to CPU due to high-speed action (bus clock 66MHz).
(IC309, IC310, IC311)
Generates each memory select signal from the memory area select signal and upper address. Generates the write signal
and upper/lower byte select signal.
· USB block
Configuration: IC204 (USB I/F), X201 (source clock: 12.000MHz), CN209 (USB connector) etc.
Function: Connects to the USB host system (mainly PC) via CN209 (B type connector) as a USB device and makes data
transfer by max.11Mbps. DMA function of CPU is utilized to transfer the data.
· SD card block
Configuration: IC205 (SD card I/F), IC209, X202(20MHz), CN211 (SD card connector) and so on.
Function: Loads the main program and the system data from the SD card connected to CN211 by 10Mbps. Restores the
system data periodically.
· MOH/PAGING block
Configuration: IC405, IC406 (CODEC), IC408, IC409 (OP Amp), IC410 (Melody IC), Q407~Q410 (transistor), JK401~JK404
(pin jack) etc.
Function: The external music on hold 1 is input from JK404 and is A/D converted in IC405 via AGC (Auto Gain Control)
circuit, which consists of IC408, Q407, Q409 and other CR, and then is connected to the call line HW. Likewise the external
music on hold 2 is input from JK403 and is made A/D conversion in IC406 via AGC (Auto Gain Control) circuit, which
consists of IC409, Q408, Q410 and other CR, and then is connected to the call line HW. The external music on hold 2 and
IC410 is exclusively connected to IC406 input (by software control).
The various tones & DTMF tone and the voice data generated in IC102 (ASIC) are made D/A conversion in IC405 and
IC406. They are output via JK402, JK401 respectively.
· Power Supply block
Configuration: IC402 (DC/DC converter), IC403 (1.8V regulator), IC404 (1.9V regulator), IC411 (OP Amp), IC413 (negative
power regulator), Q403, Q404, Q405, Q411, Q412 (transistor), L401, C408, C453, C454, D406~D409, BAT401, IP401,
IP402 (circuit protection device) and so on.
Function:
+15V input is made step-down to +3.3V by DC/DC converter circuit that consists of IC402, L401, Q412 and C408, and is
supplied to each IC power. Also, it monitors +3.3V output voltage and turns ON Q411 to block +15V input when over voltage
is supplied.
+15V input is dropped to +9.4V by Q403 and is supplied to RS232C driver with the inverted voltage (about 9.1V) generated
in IC413, C453 and C454.
+3.3V generated in DC/DC converter is converted to 1.8V in the back board or IC403 and Q405 via Q404 and supplied to
IC101 core power, and also is converted to 1.9V in IC404 via the back-flow prevention diode D407 and supplied to IC101
29
KX-TDA100BX
clock block power.

BAT401, which is a lithium battery for memory backup, is connected to the power supply of IC301, IC302 (SRAM) via D408,
D409.
IC411 compares BAT401 output voltage to the reference voltage (about 2.8V) and drives LED (BATALM) that indicates
dropping of backup voltage.
IP401 and IP402 block the line respectively when over current flows to +15V and +3.3V line.
10 BACK BOARD CIRCUIT OPERATION

The back board (BB) connects signals between all cards in main unit. It also supplies power from the power supply unit (PSU)
to the cards.
CONNECTORS EXPLANATION
(1) Power Supply Unit Connector: CN100
(2) Free Slot Connectors: CN103-CN106
(3) Option Card Slot Connector: CN107
(4) MPR Card Connector: CN112
(5) RS-232C Connector: CN113
CN113 is connected to D-Sub connector in front of the product.
(6) LED Connector: CN114
CN114 is connected to LED Board on the product.
30
KX-TDA100BX
11 TROUBLESHOOTING GUIDE
11.1. INTRUDUCTION
First, check which part of the system is causing the trouble. Follow the flowchart provided below, and replace each unit in turn
with a working unit to identify the damaged unit.
Even when damaged unit is found out, it may mean that not the cause in the unit but the damaged cause in another unit.
31
KX-TDA100BX
11.2. TYPICAL EXAMPLE

The following items are typical examples when defective occur in main unit. The analysis work first shown in this chapter is
done. When you do not correspond to this chapter, or when analysis is not completed, move to the following chapter.
32
KX-TDA100BX
11.3. MPR CARD

11.3.1. Startup
Run indicator (LED201)
33
KX-TDA100BX
SD card access light does not flash
The battery alarm indication light turns on
34
KX-TDA100BX
ALARM indicator flashes

· 1 blink and 1 interval
· 2 blinks and 1 interval
(1 blink is 0.5 sec. ON and 0.5 sec. OFF. 1 interval is 2 sec.)
ALARM indicator flashes

(1 blink is 0.5 sec. ON and 0.5 sec. OFF. 1 interval is 2 sec.)
35
KX-TDA100BX
Optional service cards cannot start up
36
KX-TDA100BX
11.3.2. Phone Call

The call path cannot connect
Noise is created
37
KX-TDA100BX
11.3.3. Paging
No sound (PAGING1)
No sound (PAGING2)
38
KX-TDA100BX
Noise is Heard (PAGING1)
Noise is Heard (PAGING2)
39
KX-TDA100BX
Sound is small (PAGING1)
Sound is small (PAGING2)
40
KX-TDA100BX
11.3.4. MOH Using

No sound is heard (MOH1)
41
KX-TDA100BX
No sound is heard (MOH2)
42
KX-TDA100BX
Sound is small or loud (MOH1)
Sound is small or loud (MOH2)
43
KX-TDA100BX
11.3.5. USB Connection

Unable to connect
44
KX-TDA100BX
Connection error occurs
45
KX-TDA100BX
11.3.6. RS-232C Connection

Unable to connect
46
KX-TDA100BX
Connecting speed is slowly
47
KX-TDA100BX
11.3.7. SD Card I/F

Unable to save the system data
48
KX-TDA100BX
11.3.8. Other
The clock data is deleted (unset table)
49
KX-TDA100BX
11.4. ERROR LOG

When a major system error occurs in the main unit (Hybrid IP-PBX), the ALARM indicator on the front of the cabinet turns on
red, and the system logs the error information.
11.4.1. Error Log Display Format

Example: KX-TDA Maintenance Console
Example: Station Message Detail Recording (SMDR)
Description
Item Description
1 Date Date of the error detection
2 Time Time of the error detection
3 Level Major Alarm (MJ ALM):
Errors that affect the whole system operation, or result in system failure
Minor Alarm (MN ALM):
Errors that affect certain part of system operation
4 Error Code Three-digit error code
5 Sub Code Five-digit sub code (XYYZZ)
X: Cabinet number (1 to 4)
YY: Slot number
KX-TDA100: 00 to 06 (00: MPR slot; 01 to 05: Free slot; 06: Option slot)
KX-TDA200: 00 to 11 (00: MPR slot; 01 to 10: Free slot; 11: Option slot)
ZZ: Physical port number (01 to 16)
For OPB3 card, sub slot number + port number will be displayed.
Sub slot 1: 11 to 14
Note:
When there is no parameter for slot and physical port number, YY and ZZ
will be displayed as "00".
Example: Sub code for MPR card = 10000
6 Error Message Error description (maximum 36 characters)
50
KX-TDA100BX
11.4.2. List of Errors and Solutions

The tables below list the errors and their solutions.
When an error whose error code is indicated with "*" occurs in the main unit (Hybrid IP-PBX), the ALARM indicator on the front
of the cabinet turns on red, and the system logs the error information.
When the error conditions indicated by the error codes "021", "091", "230", and "510" are recovered, the ALARM indicator will
turn off automatically, indicating successful troubleshooting. When other errors are logged, the ALARM indicator will turn off
only when the log for major or minor errors is cleared from the KX-TDA Maintenance Console.
In other words, the ALARM indicator will turn off under the following conditions:
· When the errors "021", "091", "230", and "510" are logged: when the error conditions are recovered
· When other errors are logged: when the log for major or minor errors is cleared from the KX-TDA Maintenance Console
MPR Card Initial Self Diagnosis
Error Code Error Message PROBABLE CAUSE SOLUTION
100 SRAM readwrite error · MPR card malfunction · See if the MPR card is installed properly
101 Flash write error · Press the Reset Button
102 Flash boot check error
· Replace the MPR card (be sure to turn off the main unit
103 SDRAM eadwrite error (Hybrid IP-PBX) when replacing)
104 ASIC local bus register
access error
105 ASIC CT bus HW NG
106 ASIC Local HW0 NG
108 SD card not mounted · SD Memory Card not installed · See if the SD Memory Card is installed properly
· Defective data in SD Memory Card · Replace the SD Memory Card
· MPR card malfunction · Replace the MPR card (be sure to turn off the main unit
(Hybrid IP-PBX) when replacing)
109 ASIC HDLC error · MPR card malfunction · See if the MPR card is installed properly
110 ASIC DMAC error · Press the Reset Button
LPR (Optional Service Card with Local Processor) Initial Self Diagnosis
210 ASIC local bus register · Optional service card malfunction: · See if the corresponding optional service card is installed
access error DHLC, DLC, CSIF, T1, PRI, OPB3, properly
CTI-LINK, E&M, IP-GW
· Pull out and re-insert the corresponding optional service
211 Speech path loop-back · Optional service card malfunction: card
check error DHLC, DLC, SLC, CSIF, LCOT,
T1, PRI, OPB3, CTI-LINK, E&M, · Press the Reset Button
IP-GW · Replace the corresponding optional service card
212 Echo cancellor access · Optional service card malfunction:
error CSIF, ECHO
213 CSINF frame sync.
error
214 DSP Boot check error · Optional service card malfunction:
T1
215 Framer IC access error · Optional service card malfunction:
T1, PRI
216 MSG card DSP error · Optional service card malfunction:
MSG, OPB3
217 MSG card data error · Optional service card malfunction: · See if the corresponding optional service card is installed
MSG, OPB3 properly
· Erroneous recording of messages · Pull out and re-insert the corresponding optional service
card
· Press the Reset Button
· Re-record the messages
· Replace the corresponding optional service card
218 LANC register access · Optional service card malfunction: · See if the corresponding optional service card is installed
error CTI-LINK properly
card
· Press the Reset Button
51
KX-TDA100BX

219 PT I/F error · Optional service card malfunction: · See if the corresponding optional service card is installed
DHLC, DLC properly
· Software error due to external · Pull out and re-insert the corresponding optional service
factors card
· Breaking of telephone · Press the Reset Button
cord/interference of noise
· Check the wiring
System Start-up and On-line Operation

000* MPR WDT overflow · MPR card malfunction · Press the Reset Button
001 SDRAM bit error · Erroneous processing of MPR card · Reprogram the main unit (Hybrid IP-PBX)
software
· Software error due to external (Hybrid IP-PBX) when replacing)
factors
002 System Reset · Reset Button is pressed · Ignore if not frequent
· Power failure · Press the Reset Button
· MPR card malfunction · Reprogram the main unit (Hybrid IP-PBX)
· Erroneous processing of MPR card · Replace the MPR card (be sure to turn off the main unit
software (Hybrid IP-PBX) when replacing)
· Software error due to external
factors
010* AC power down · Power supply system malfunction · Check the power supply system
(e.g., power failure, power noise,
· See if the AC cord is connected properly
trouble with UPS)
· Check the AC cord
· Bad connection or breaking of AC
cord · Replace the AC cord (be sure to turn off the main unit
· Power supply circuit (PSU, back
board) malfunction · Replace the PSU (be sure to turn off the main unit (Hybrid
IP-PBX) when replacing)
· Replace the back board (be sure to turn off the main unit
011* DC power down · AC power down · Check the power supply system
· Power supply circuit (PSU, back · See if the AC cord is connected properly
board) malfunction
· Check the AC cord
· Detection of over current (short
· Replace the AC cord (be sure to turn off the main unit
circuit on optional service cards)
· Replace the PSU (be sure to turn off the main unit (Hybrid
· Remove the optional service cards and restart the main unit
(Hybrid IP-PBX)
012* MPR RAM battery low · Battery out · Replace the MPR card (be sure to turn off the main unit
· MPR card malfunction
014* FAN Alarm · PSU-L malfunction · See if anything is jammed in the fan
· Replace the PSU (be sure to turn off the main unit (Hybrid
016 CS overload · Defective cable · Check the cable diameter and length
· CS malfunction · Replace the CS
· Optional service card malfunction: · Replace the corresponding optional service card
CSIF
018 CS superframe · Optional service card malfunction: · Replace the corresponding optional service card
synchronization failure CSIF
020* SD file access error · SD Memory Card malfunction · Press the Reset Button
· Bad connection of SD Memory · Reprogram the main unit (Hybrid IP-PBX)
Card
· Replace the SD Memory Card
021* SD Memory Card · SD Memory Card not installed (Hybrid IP-PBX) when replacing)
disconnected
· Bad connection of SD Memory
Card
· SD Memory Card malfunction
52
KX-TDA100BX

022* Not enough free space · Not enough memory space · Delete the files whose file names start with "$" from SD
on SD card available to save the system data, Memory Card
or to upload system files from the
· Delete the "Pxxx" files (old program files of optional service
KX-TDA Maintenance Console
cards) from SD Memory Card. "xxx" indicates the card type
(e.g., "PDHLC" for DHLC card)
Note:
Do not delete the "PMPR" file; it is the program file of the
MPR card.
023* System data file · Old system files on SD Memory · Restore the backup files
version error Card
· Re-install the software
024* System initialization file · Defective system files on SD
version error Memory Card
025* Card initialization file
version error
026* LCD file version error
027* System data file
checksum error
028* System initialization file
checksum error
checksum error
030* LCD file checksum
error
031* System data file not · SD Memory Card not installed · Press the Reset Button
found
· Bad connection of SD Memory · Reprogram the main unit (Hybrid IP-PBX)
032* System initialization file Card
not found · Replace the SD Memory Card
033* Card initialization file · SD Memory Card malfunction
not found · MPR card malfunction (Hybrid IP-PBX) when replacing)
034* LCD file not found
035* System data file
access error
036* System initialization file
access error
access error
038* LCD file access error
040 Calendar IC failure · Erroneous processing of calendar · Reset the system clock
IC of MPR card
· MPR card malfunction (Hybrid IP-PBX) when replacing)
090 Card limitation over · Too many optional service cards · Reduce the number of optional service cards
installed
091 PT connection over · Too many PTs connected · Reduce the number of PTs
200 LPR start up error · Optional service card malfunction: · Pull out and re-insert the corresponding optional service
(ROM NG) DHLC, DLC, CSIF, T1, PRI, OPB3, card
201* LPR start up error CTI-LINK, E&M, IP-GW
· Press the Rest Button
(RAM NG)
202* LPR start up error (No · Optional service card malfunction: · Pull out and re-insert the corresponding optional service
Program) DHLC, DLC, CSIF, T1, PRI, OPB3, card
203* LPR start up error CTI-LINK, E&M, IP-GW
(Version NG)
204* LPR start up error · Update the software of the corresponding optional service
(Version NG) card
205* LPR start up error (No · Replace the corresponding optional service card
response)
206 LPR start up error
(Card type NG)
207 LPR start up error
(Check SUM NG)
230* Card disconnected · Optional service card not installed · See if the corresponding optional service card is installed
properly properly
· Optional service card malfunction · Pull out and re-insert the corresponding optional service
card
· Back board malfunction
53
KX-TDA100BX

231 LPR alive check error · Optional service card malfunction: · See if the corresponding optional service card is installed
232 MPR-LPR DHLC, DLC, CSIF, T1, PRI, OPB3, properly
communication error CTI-LINK, E&M, IP-GW
233 LPR data check error · Back board malfunction card
234 DPLL clock failure · MPR card malfunction · Press the Rest Button
235* CS clock failure · Optional service card malfunction: · Replace the corresponding optional service card
CSIF
250 T1/E1 DSP failure · Optional service card malfunction: · See if the corresponding optional service card is installed
T1 properly
251 MSG DSP failure · Optional service card malfunction: · Replace the corresponding optional service card
MSG
300* Digital trunk out of · Network (digital CO line) · Check the signals from the networkd is installed properly
synchronization malfunction
· Check the cable
301* Digital trunk RAI · Optional service card malfunction:
reception · See if the A/B switch is set to A on the corresponding
PRI, T1, CTI-LINK
302* Digital trunk AIS optional service card
reception · Wrong A/B switch setting: PRI, T1
· See if the corresponding optional service card is installed
303* Multiframe out of properly
synchronization · Replace the corresponding optional service card
304* Frame error
305* Data Link failure · Data link between the CS and · Check the connection between the CS and CSIF card
CSIF card failed
· Check the connection between the network and PRI card
· Data link between the network
and PRI card failed
307 LAN No Carrier · IP-GW card not connected to the · Check the connection between the LAN and IP-GW card
LAN
310* Port Link Failure · Voice Mail malfunction · Check the Voice Mail
· Ports defective on optional service · See if the corresponding optional service card is installed
card: DHLC, DLC properly
390 Digital signal · Synchronization of digital line · This information is logged when synchronization of digital
synchronization established or restored line is established, and does not indicate an error condition
established that needs to be solved
391 Data Link established · Connection with PC Phone/PC · This information is logged when connection with PC
Console or Voice Mail (DTMF Phone/PC Console or Voice Mail (DTMF Integration) is
Integration) established or restored established, and does not indicate an error condition that
needs to be solved. However, if this is logged frequently
(with "305 Data Link failure"), check the connection as it
may not be done properly.
392 Clock master card · Clock master card has been · Check if the proper card is selected as the new clock
selected changed to the one indicated by master card
the sub code
510* SMDR disconnect · RS-232C cable not connected · Check the RS-232C cable
· Breaking of RS-232C cable · Check the terminal equipment
· Printer (terminal equipment)
malfunction
54
KX-TDA100BX
12 DIAGNOSIS
12.1. DIAGNOSIS FEATURES
Card Test and Pair Port Test is in Diagnosis Features.
12.1.1. Card Test
Card Test -SUMMARY
Description
Diagnose all kind of Cards.
Parallel of Diagnose item of Card Tests and every Cards
DHLC DLC SLC8/L MSLC/ CS-INF LCOT T1 E1 BRI PRI OPB3 E&M CTI-
SLC8 SLC16 LINK
Local loop back diagnosis X X X X X X X X X X X X
Card CT bus diagnosis X X X X X X X X X X X X
DTMF receive test X X X X
PT loop back diagnosis X X
DSP DTMF generator/receiver X X
diagnosis
DSP DTMF receiver diagnosis X X
Framer IC alarm signal detection X X X
diagnosis
Framer IC error detection X X X
diagnosis
CS-INF loop back diagnosis X
Super frame synchronization X
diagnosis
Caller ID card loop back diagnosis X
Extension mode setting test X
CTI-LINK loop back diagnosis X
12.1.1.1. Local Loop Back Diagnosis

Diagnose by transmission of the data from MPR to Card, and doing the Loop back test to return the data to MPR.
The point to do Loop back is different from the every cards, be able to do full diagnosis by Loop back test on the every points.
Local loop back diagnosis test
Primary circuit Primary circuit loop back test
Framer IC ST path (Analog) IC Analog I/F loop back test
Framer IC (Digital) IC Digital I/F loop back test
ASIC CODEC (PITS) PITS I/F test loop back
Local HW I/F point Local HW I/F loop back test
Local TSW point Local TSW loop back test
Local loop back diagnosis test of every Cards

SLC8 SLC16 LINK
Primary circuit X X X
Framer IC ST path (Analog) X X
Framer IC (Digital) X X X X
ASIC CODEC (PITS)
Local HW I/F point X X X X X X X X X
Local TSW point X X X X X X X X X X X X
Diagnosis result of every test points

OK loop back diagnosis OK
NG loop back diagnosis NG
55
KX-TDA100BX
12.1.1.2. Card CT Bus Diagnosis

Diagnose CT bus by Loop back test to use CT bus
SLC8 SLC16 LINK
Object of Card X X X X X X X X X X X X X
Diagnosis result
OK Card CT bus diagnosis OK
NG Card CT bus diagnosis NG
12.1.1.3. DTMF Receive Test

Diagnosis DTMF receiver
SLC8 SLC16 LINK
Object of Card X X X X
Diagnosis result
OK DTMF receive test OK
NG DTMF receive test NG
12.1.1.4. PT Loop Back Diagnosis

Diagnosis PT by Loop back test
SLC8 SLC16 LINK
Object of Card X X
PT loop back diagnosis test channel

Cch port xx C channel Port No.xx test
Dch port xx D channel Port No. xx test
Bch port xx B channel Port No. xx test
PT loop back diagnosis test

Primary circuit Primary circuit loopback test
ASIC (PT I/F) PT I/F loopback test
Diagnosis result
OK PT loop back diagnosis OK
NG PT loop back diagnosis NG
12.1.1.5. DSP DTMF Generator / Receiver Diagnosis

Diagnosis DTMF generator/receiver of DSP in the Card
SLC8 SLC16 LINK
Object of Card X X
diagnosis point
Time slot Time slot test
DSP ST loop back DSP ST point loop back test
DSP digital loop back DSP digital point loop back test
Diagnosis result
OK DSP DTMF generator/receiver diagnosis OK
NG DSP DTMF generator/receiver diagnosis NG
56
KX-TDA100BX
12.1.1.6. DSP DTMF Receiver Diagnosis

Diagnose DTMF receiver of DSP in the Card to use DTMF generator of DSP
SLC8 SLC16 LINK
Object of Card X X
Diagnosis point
Time slot Time slot test
DSP ST loop back DSP ST point loop back test
DSP digital loop back DSP digital point loop back test
Diagnosis result
12.1.1.7. Framer IC Alarm Signal Detection Diagnosis

Diagnose the feature to detect the alarm signal of Framer IC is normal action.
SLC8 SLC16 LINK
Object of Card X X X
Diagnosis point
RAI Yellow alarm signal detection test
AIS Blue alarm signal detection test
Primary circuit Primary circuit alarm signal detection test
Diagnosis result
OK Framer IC alarm signal detection diagnosis OK
NG Framer IC alarm signal detection diagnosis NG
12.1.1.8. Framer IC Error Detection Diagnosis

Diagnose the feature to detect the alarm signal of Framer IC is normal action.
SLC8 SLC16 LINK
Object of Card X X X
Diagnosis point
Bipolar violation error Bipolar violation error detection test
CRC error CRC error detection test
Framing error Framing error detection test
Primary circuit Primary circuit error detection test
Diagnosis result
12.1.1.9. CS-INF Loop Back Diagnosis

Diagnose by Loop back test to CS-INF
SLC8 SLC16 LINK
Object of Card X
CS-INF loop back diagnosis test channel

Dch port xx D channel Port No. xx test
Bch port xx B channel Port No. xx test
Diagnosis point
DNIC analog DNIC analog loop back test
DNIC digital DNIC digital loop back test
Diagnosis result
OK CS-INF loop back diagnosis OK
NG CS-INF loop back diagnosis NG
57
KX-TDA100BX
12.1.1.10. Super Frame Synchronization Diagnosis

Diagnose Super frame synchronization feature of CS-INF
SLC8 SLC16 LINK
Object of Card X
Diagnosis point
DECT DECT super frame synchronization test
SS SS super frame synchronization test
Diagnosis result
OK Super frame synchronization diagnosis OK
NG Super frame synchronization diagnosis NG
12.1.1.11. Caller ID Card Loop Back Diagnosis

Diagnose by Loop back test to Caller ID card (Optional Card of LCOT)
SLC8 SLC16 LINK
Object of Card X
Diagnosis result
OK Caller ID card loop back diagnosis OK
NG Caller ID card loop back diagnosis NG
12.1.1.12. Extension Mode Setting Test

Diagnose the normal change from outside line mode to inside line mode
SLC8 SLC16 LINK
Object of Card X
Diagnosis result
OK Extension mode setting test OK
NG Extension mode setting test NG
12.1.1.13. CTI-LINK Loop Back Diagnosis

Diagnose by Loop back test to CS-INF
SLC8 SLC16 LINK
Object of Card X
Diagnosis result
OK CTI-LINK loop back diagnosis OK
NG CTI-LINK loop back diagnosis NG
12.1.2. Pair Port Test

Pair Port Test -SUMMARY
Description
Diagnosis Pair Port Test to pair up inside line and outside line
SLC8 SLC16 LINK
Object of Card X X X X
Diagnosis result
OK Pair Port Test OK
NG Pair Port Test NG
Detail Diagnosis result

Line current OFF (Ext->CO) There is no local current from inside line to outside line
Line current ON (Ext->CO) There is local current from inside line to outside line
Off hook detection (CO->Ext) Off-hook detection from outside line to inside line
DTMF detection (CO->Ext) DTMF transmission/detection from outside line to inside line
DP detection (CO->Ext) SP transmission/detection from outside line to inside line
BELL detection (Ext->CO) Bell transmission/detection from inside line to outside line
Speech path (Ext->CO) Call lime from inside line to outside line
Speech path (CO->Ext) Call lime from outside line to inside line
58
KX-TDA100BX
12.2. DIAGNOSIS TEST

1. Click [Diagnosis] of [Utility].
59
KX-TDA100BX
2. Pair Port Test operation Select card for Test.
3. Click [Pair Port Test].
60
KX-TDA100BX
4. Click [OK].
5. Click [Cancel].
61
KX-TDA100BX
6. Card Test operation Select card for Test.
7. Click [Card Test].
62
KX-TDA100BX
8. Click [OK].
9. Click [Cancel].
63
KX-TDA100BX
13 IC DATA
13.1. IC101
Pin No. Pin Name I/O Description

1 MD1 I Clock mode setting
3 Vcc-TRC*1 - Power for RTC
4 XTAL2 O Crystal oscillator terminal for built-in RTC
5 EXTAL2 I Crystal oscillator terminal for built-in RTC (*6)
6 Vcc-TRC*1 - Power for RTC
7 NMI I Nonmaskable interrupt request
8 IRQ0/IRL0/PTH[0] I External interrupt request/input port H
12 IRQ4/PTH[4] I External interrupt request/input port H
13 D31/PTB[7] I/O Data bus/I/O port B
19 VssQ - Power for I/O (0V)
21 VssQ - Power for I/O (3.3V)
23 D23/PTA[7] I/O Data bus/I/O port A
27 Vss - Power supply (0V)
- Vss - Power supply (0V)
64
KX-TDA100BX

29 Vcc - Power supply (*3)
- Vcc - Power supply (*3)
34 D15 I/O Data bus
35 VccQ - Power for I/O (3.3V)
36 D14 I/O Data bus
37 D13 I/O Data bus
38 D12 I/O Data bus
39 D11 I/O Data bus
40 D10 I/O Data bus
41 D9 I/O Data bus
42 D8 I/O Data bus
43 D7 I/O Data bus
44 D6 I/O Data bus
46 D5 I/O Data bus
48 D4 I/O Data bus
49 D3 I/O Data bus
50 D2 I/O Data bus
51 D1 I/O Data bus
52 D0 I/O Data bus
53 A0 O Address bus
54 A1 O Address bus
55 A2 O Address bus
56 A3 O Address bus
58 A4 O Address bus
60 A5 O Address bus
61 A6 O Address bus
62 A7 O Address bus
63 A8 O Address bus
64 A9 O Address bus
65 A10 O Address bus
- Vss O Power supply (0V)
81 Vss - Power supply (*3)
- Vss - Power supply (*3)
87 BS/PTK[4] O/I/O Bus cycle start signal/I/O port K
88 RD O Read stroke
89 WE0/DQMLL O D7-D0 select signal/DOM (SDRAM)
90 WE1/DQMLU/WE O D15-D8 select signal/DOM (SDRAM)
91 WE2/DQMUL/ICIORD/ O/I/O D23-D16 select signal/DOM (SDRAM) /PCMCIA I/O read/I/O port K
PTK[6]
65
KX-TDA100BX

92 WE3/DQMUU/ICIOW O/I/O D31-D24 select signal/DOM (SDRAM) /PCMCIA I/O write/I/O port K
R/PTK[7]
93 RD/WR O Read/Write
94 AUDSYNC/PTE[7] O/I/O AUD synchronization/I/O port E
96 CS0/MCS[0] O Chip select 0/mask ROM chip select 0
98 CS2/PTK[0] O/I/O Chip select 2/I/O port K
101 CS5/PTK[3] O/I/O Chip select 5/CE1 (Area 5PCMCIA)/I/O port K
102 CS6/CE1B O Chip select 6/CE1 (Area 6PCMCIA)
103 CE2A/PTE[4] O/I/O CE2(Area 5PCMCIA)/ I/O port K
104 CE2B/PTE[5] O/I/O CE2(Area 6PCMCIA)/ I/O port K
105 CKE/PTK[5] O/I/O CK Enable (SDRAM) / I/O port K
106 RAS3L/PTJ[0] O/I/O RAS for low 32M/64M bytes address (SDRAM) /I/O port J
107 PTJ[1] I/O I/O port J
108 CASL/PTJ[2] O/I/O RAS for low 32M/64M bytes address (SDRAM) /I/O port J
110 CASU/PTJ[3] O/I/O RAS for low 32M bytes address (SDRAM) /I/O port J
114 DACK0/PTD[5] O/I/O DMA acknowledge0/I/O port D
115 DACK1/PTD[7] O/I/O DMA acknowledge1/I/O port D
116 PTE[6} I/O I/O port E
117 PTE[3} I/O I/O port E
118 RAS3U/PTE[2] O/I/O RAS for low 32M bytes address (SDRAM) / I/O port E
119 PTE[1] I/O I/O port E
120 TDO/PTE[0] O/I/O Test data output/I/O port E
121 BACK O Bus acknowledge
122 BREQ I Bus request
123 WAIT I Hardware wait request
124 RESETM I Manual reset request
125 ADTRG/PTH[2] I Analog trigger/input port H
126 IOIS16/PTG[7] I IOIS168 (PCMCI) / I/O port G
127 ASEMD0/PTG[6] I ASE mode:4/I/O port G
128 ASEBRKAK/PTG[5] I/O ASE break acknowledge/I/O port G
129 PTG[4]/CKIO2 I/O Input port G/clock output
130 AUDATA[3]/PTG[3] I/O/I AUD data/input port G
136 TRST/PTF[7]/PINT[15] I Test reset/input port F/port interruption
137 TMS/PTF[6]/PINT[14] I Test mode switch/input port F/port interruption
138 TDI/PTF[5]/PINT[13] I Test mode switch/input port F/port interruption
139 TCK/PTF[4]/PINT[12] I Test clock/input port F/port interruption
140 IRS3/PTF[3]/PINT[11] I External interrupt request/input port F/port interruption
145 Vcc-PLL1*2 - Power for PLL1 (*3)
146 CAP1 - External capacity terminal for PLL1
147 Vss-PLL1*2 - Power for PLL1 (0V)
148 Vss-PLL2*2 - Power for PLL1 (1V)
149 CAP2 - External capacity terminal for PLL2
150 Vcc-PLL2*2 - Power for PLL2 (*3)
151 AUDCK/PTH[6] I AUD clock/input port H
66
KX-TDA100BX

155 XTAL O Clock oscillator terminal
156 EXTAL I External clock/crystal oscillator terminal
157 STATUS0/PTJ[6] O/I/O Processor status
158 STATUS0/PTJ[7] O/I/O Processor status
159 TCLK/PTH[7] I/O Clock I/O for TMU or RTC/I/O port J
160 IRQOUT O Interrupt request notification
162 CKIO I/O System clock I/O
164 TxD0/SCPT[0] O Transmission data 0/output port for SCI
165 SCK0/SCPT[1] I/O Serial clock 0/output port for SCI
170 RTS0/SCPT[6] O/I/O
171 RxD0/SCPT[0] I Transmission data 0/input port for SCI
176 CTS2/IRQ5/SCPT[7] I Transmission clear 2/external interrupt request /I/O port for SCI
177 MCS[7]/PTC[7]/PINT[7 O/I/O Mask ROM chip select/I/O port C/port interruption
]
]
]
]
182 WAKEUP/PTD[3] O/I/O Interrupt request notification on standby mode/I/O port D
184 RESETOUT/PTD[2] O/I/O Reset output/I/O port D
185 MCS[3]/PTC[3]/PINT[3 O/I/O/I Mask ROM chip select/I/O port C/port interruption
]
]
]
]
189 DRAK0/PTD[1] O/I/O DMA request accepting/I/O port D
190 DRAK1/PTD[0] O/I/O DMA request accepting/I/O port D
191 DREQ0/PTD[4] I DMA request/input port D
192 DREQ1/PTD[0] I DMA request/input port D
193 RESETP I Power on reset request
194 CA I Chip active (hardware standby request signal)
195 MD3 I Bus width setting for area 0
196 MD4 I Bus width setting for area 1
197 MD5 I Endian setting
198 Avss - Power for analog (0V)
199 AN[0]/PTL[0] I AD converter input/input port L
205 Avcc - Power for analog (3.3V)
206 AN[6]/DA[1]/PTL[6] I AD converter input/DA converter output/input port L
207 AN[7]/DA[0]/PTL[7] I AD converter input/DA converter output/input port L
208 AVss - Power for analog (0V)
67
KX-TDA100BX
14 TERMINAL GUIDE OF ICS, TRANSISTORS AND DIODES
68
KX-TDA100BX
15 HOW TO REPLACE A FLAT PACKAGE IC

15.1. PREPARATION 15.3. REMOVING SOLDER FROM
· PbF (: Pb free) Solder BETWEEN PINS
· Soldering Iron 1. Add a small amount of solder to the bridged pins.
Tip Temperature of 700°F ± 20°F (370°C ± 10°C) 2. With a hot iron, use a sweeping motion along the flat part of
Note: We recommend a 30 to 40 Watt soldering iron. An the pin to draw the solder from between the adjacent pads.
expert may be able to use a 60 to 80 Watt iron where
someone with less experience could overheat and damage
the PCB foil.
· Flux
Recommended Flux: Specific Gravity → 0.82.
Type → RMA (lower residue, non-cleaning type)
Note: See ABOUT LEAD FREE SOLDER (PbF: Pb free)
(P.3).
15.2. PROCEDURE
1. Tack the flat pack IC to the PCB by temporarily soldering
two diagonally opposite pins in the correct positions on the
PCB.
Be certain each pin is located over the

correct pad on the PCB.
2. Apply flux to all of the pins on the IC.
3. Being careful to not unsolder the tack points, slide the

soldering iron along the tips of the pins while feeding
enough solder to the tip so that it flows under the pins as
they are heated.
69
KX-TDA100BX
16 CABINET AND ELECTRICAL PARTS LOCATION
70
KX-TDA100BX
16.1. EXTENSION BOARDS FOR SERVICING
71
KX-TDA100BX
17 ACCESSORIES AND PACKING MATERIALS
72
KX-TDA100BX
18 REPLACEMENT PARTS LIST

Note: Ref. Part No. Part Name & Description Remarks
No.
1. RTL (Retention Time Limited) 9 PSMH1205Z CHASSIS, LED
The marking (RTL) indicates that the Retention Time is
10 PSHD1091Z BOLT WITH NUT
limited for this item.
11 PSKV1016Z1 COVER, RIGHT SIDE ABS-HB
After the discontinuation of this assembly in production, the 12 PSYCTDA100AL COVER, FRONT PC+ABS-
item will continue to be available for a specific period of 5V
13 PSMD1040Y FRAME, LOWER
time. The retention period of availability depends on the
14 PSMH1230Z FRAME
type of assembly and the laws governing parts and product 15 PSMH1222Z ANGLE, RS-232C
retention. At the end of this period, the assembly will no 16 PSMH1206Y ANGLE
longer be available. 17 PSMH1207Z ANGLE
18 PSKK1035Z1 LID PC+ABS-
2. Important safety notice 5V
Components identified by the mark indicates special 19 PSKR1001Y1 GUIDE, CABLE PC+ABS-
5V
characteristics important for safety. When replacing any of
these components, only use specified manufacture´s parts. 20 PSKL1016Z1 STAND ABS-HB
3. The S mark means the part is one of some identical parts. 21 PSMH1234Z ANGLE, FRONT
22 PQHR10379Z CLAMPER
For that reason, it may be different from the installed part. 23 PSGB1001Z BADGE PS-HB
4. ISO code (Example : ABS-94HB) of the remarks column 24 PSQT1431Z LABEL, WARNING
shows quality of the material and a flame resisting grade 25 PSYETDA100BX NAME PLATE
26 PSQT1990Z LABEL, CAUTION
about plastics.
27 PSJS03P16Z CONNECTOR, LED
5. RESISTORS & CAPACITORS 28 PSJS09P12Z CONNECTOR, RS-232C
29 PQHD10011V SCREW
Unless otherwise specified;
All resistors are in ohms (Ω), k=1000Ω, M=1000kΩ 30 PSUS1022Z SPRING
31 XUC3VW RETAINING RING
All capacitors are in MICRO FARADS (µF), p=µ(µF)
32 PSMH1244Z CHASSIS, FRONT
*Type & Wattage of Resistor 33 PSUS1021Y SPRING
34 PSHD1088Z SCREW
18.2. ACCESSORIES AND PACKING

MATERIALS
Ref. Part No. Part Name & Description Remarks
No.
A1 PSJA1007Z POWER CORD (AC CORD)
A2 PQJP1E1Z PLUG
A3 XYN4+J18FZ SCREW
A4 PQHE17Z MOUNTING BRACKET
A5 XTB5+20AFY SCREW
A6 PSZETDA100BX ACCESSORY PARTS,SD CARD
A7 PSLB5D1 INSULATOR
A8 PSMD1042Z MOUNTING BRACKET
A9 PSQX2227YCD CD-ROM, INSTALLATION MANUAL
(FOR USER)
A10 PSQW2011Y LEAFLET, SAFETY INFORMATI
A11 PSQX2849ZCD CD-ROM (FOR USER DEALER)
A12 PSJA1081Z POWER CORD (AC CORD)
P1 PSZKTDA100BX PACKING CASE

P2 PSPD1172Z CUSHION
P3 PSPD1173Z CUSHION
18.1. CABINET AND ELECTRICAL P4

P5
PSPN1137Y
PSPD1182Z
ACCESSORY BOX
CUSHION
PARTS P6 PSPD1171Y CUSHION
P7 PSPD1170Y CUSHION
Ref. Part No. Part Name & Description Remarks P8 PSPD1183Z CUSHION
No. P9 XZB05X08A03 PROTECTION COVER (FOR SCREW)
1 PSKV1023Z1 COVER, TOP PC+ABS-
5V
P10 XZB10X15A04 PROTECTION COVER
2 PSKV1017Z1 COVER, LEFT SIDE ABS-HB
P11 XZB18X27A04 PROTECTION COVER (FOR CD-ROM)
3 PSMD1035Z FRAME, SIDE
P12 PSPP1070Z PROTECTION COVER (FOR SD
4 PSMD1040Y FRAME, BASE CARD)
5 PSMH1232Z FRAME,BACK BOARD P13 PQPP143Z PROTECTION COVER (FOR SET)
6 PSMD1041Z COVER, BACK P14 PSPP1069Z PROTECTION COVER
7 PSMH1264Z COVER, HOLD P15 XZB50X30A06 PROTECTION COVER (FOR
8 PSHR1235Z GUIDE RAIL PC+ABS- MOUNTING BRACKET)
5V
73
KX-TDA100BX

18.3. MPR CARD PARTS No.
D409 MA728 DIODE(SI)
No.
DA401 MA143 DIODE(SI)
PCB1 PSWP1DA100BX MPR CARD ASS´Y (RTL)
DA402 MA143 DIODE(SI)
(ICS)
LED101 PSVD1VGCT LED
IC101 C2DBYJ000009 IC
LED103 PSVD1SRCT LED
IC102 C1CB00001395 IC
IC103 C1CB00001497 IC
(CONNECTORS)
IC107 C0EBE0000176 IC
CN103 K1KA90B00008 CONNECTOR, 90P
IC110 C0JBAB000407 IC S
CN205 K1KAC0A00037 CONNECTOR, 120P
CN206 K1KB30A00117 CONNECTOR, 30P
IC120 PQVIMC1488MR IC
CN207 PSJP07A44Z CONNECTOR, 7P
IC121 PQVIMC1489MR IC
CN209 K1KB04B00036 CONNECTOR, 4P S
IC123 C0JBAZ001765 IC
CN211 K1NA09E00022 CONNECTOR, 9P
IC125 C0JBAC000264 IC
(JACKS)
IC126 C0JBAA000174 IC
JK401 PSJJ1D001Z JACK S
IC127 C0JBAZ001704 IC S
IC132 C0JBAB000381 IC
IC201 C0JBAN000187 IC S
(COMPONENTS PARTS)
IC204 C1CB00001415 IC
RA101 D1HA1038A005 RESISTOR ARRAY
IC205 MN5773 IC
RA102 D1H8R0040009 RESISTOR ARRAY
IC209 C0JBAB000504 IC
IC301 C3BBKG000060 IC S
IC302 C3BBKG000060 IC S
IC303 PSWITDA100BX IC(ROM)
IC305 C3ABPJ000054 IC S
IC306 C3ABPJ000054 IC S
RA111 EXB38VR000 RESISTOR ARRAY
IC309 C0JBAN000187 IC
IC310 C0JBAN000187 IC
IC311 C0JBAA000174 IC
IC402 PQVIS8520F33 IC
IC403 C0CBAAG00006 IC
IC404 C0CBAAB00022 IC
IC405 C0ZBZ0000553 IC
IC406 C0ZBZ0000553 IC
IC408 PQVINJM4558M IC
IC410 PSVISV7560 IC
RA123 EXB38V680JV RESISTOR ARRAY
IC412 C0CBADC00009 IC
IC413 C0DBEDA00002 IC
(TRANSISTORS)
Q101 B1GBCFEH0003 TRANSISTOR(SI)
RA128 EXRV8V470JV RESISTOR ARRAY
Q403 2SD1664Q TRANSISTOR(SI)
RA129 EXRV8V470JV RESISTOR ARRAY
Q404 2SB1132R TRANSISTOR(SI)
Q405 2SB1132R TRANSISTOR(SI)
Q406 UN5213 TRANSISTOR(SI)
Q407 2SC4081R TRANSISTOR(SI)
Q408 2SC4081R TRANSISTOR(SI)
Q409 B1ABEC000005 TRANSISTOR(SI)
Q410 B1ABEC000005 TRANSISTOR(SI)
Q411 B1DFDC000002 TRANSISTOR(SI)
RA201 D1HA1048A005 RESISTOR ARRAY S
Q412 B1DHCD000018 TRANSISTOR(SI)
QA101 B1GHCFJJ0007 TRANSISTOR(SI) S
RA204 D1H82204A024 RESISTOR ARRAY
QA103 B1GHCFJJ0007 TRANSISTOR(SI) S
(DIODES)
D402 PFVDDGD1FP3T DIODE(SI)
D403 MA8100M DIODE(SI)
D406 MA8043M DIODE(SI)
D407 MA1070400L DIODE(SI)
74
KX-TDA100BX
Ref. Part No. Part Name & Description Remarks Ref. Part No. Part Name & Description Remarks
No. No.
RA306 D1HA1038A005 RESISTOR ARRAY C174 ECUV1C104ZFV 0.1
RA308 D1HA1038A005 RESISTOR ARRAY C201 ECUV1H220JCV 22p
RA309 D1HA1038A005 RESISTOR ARRAY C202 PQCUV1A225ZF 2.2
C203 ECUV1H220JCV 22p
(CAPACITORS) C204 ECUV1A105ZFV 1
C101 PQCUV1A225ZF 2.2 C205 ECUV1C104ZFV 0.1
C102 ECUV1A105ZFV 1 C206 ECUV1C104ZFV 0.1
C103 ECUV1C104ZFV 0.1 C207 ECUV1C104ZFV 0.1
C105 ECUV1C104ZFV 0.1 C209 PQCUV1A225ZF 2.2
C106 ECUV1C104ZFV 0.1
C107 ECUV1C104ZFV 0.1 C210 ECUV1A105ZFV 1
C109 ECUV1H120JCV 12p C212 ECUV1C105ZFV 1
C112 ECUV1C104ZFV 0.1 C217 ECUV1H150JCV 15p
C114 ECUV1H120JCV 12p C218 ECUV1H150JCV 15p
C118 ECUV1C104ZFV 0.1 C220 ECUV1A105ZFV 1
C301 PQCUV1A225ZF 2.2
C120 ECUV1C104ZFV 0.1 C302 PQCUV1A225ZF 2.2
C121 ECUV1A105ZFV 1 C303 ECUV1A105ZFV 1
C125 ECUV1C104ZFV 0.1 C307 ECUV1H102KBV 0.001
C127 PQCUV1A225ZF 2.2
C128 PQCUV1A225ZF 2.2 C310 ECUV1A105ZFV 1
C129 ECUV1A105ZFV 1 C312 PQCUV1A225ZF 2.2
C131 PQCUV1A225ZF 2.2 C316 PQCUV1A225ZF 2.2
C133 PQCUV1A225ZF 2.2 C318 ECUV1A105ZFV 1
C134 PQCUV1A225ZF 2.2 C319 PQCUV1A225ZF 2.2
C135 ECUV1H220JCV 22p
C136 ECUV1H220JCV 22p C320 ECUV1C104ZFV 0.1
C402 F2G1E3310005 330
C143 PQCUV1A225ZF 2.2 C408 F2G0J4710006 470
C148 ECUV1C104ZFV 0.1 C413 ECUV1H103KBV 0.01
C415 ECUV1H103KBV 0.01
C150 ECUV1A105ZFV 1 C416 PQCUV1A225ZF 2.2
C151 PQCUV1A225ZF 2.2 C417 PSCSZ1AX106M 10
C156 ECUV1H102KBV 0.001 C418 ECUV1A105ZFV 1
C157 ECUV1H102KBV 0.001 C419 ECUV1H121JCV 120p
C420 ECUV1A105ZFV 1
C160 ECUV1A105ZFV 1 C421 ECUV1H121JCV 120p
C168 ECUV1H102KBV 0.001 C427 ECUV1C104ZFV 0.1
75
KX-TDA100BX
No. No.
R137 ERJ3GEYJ103 10k
C430 ECUV1H153KBV 0.015 R138 ERJ3GEYJ103 10k
C435 ECUV1A105ZFV 1 R140 ERJ3GEYJ330 33
C436 ECUV1A105ZFV 1 R142 ERJ3GEYJ330 33
C437 ECUV1H333KBV 0.033 R143 ERJ3GEYJ330 33
R146 ERJ3GEYJ680 68
C441 ECUV1H332KBV 0.0033
C442 ECUV1H105ZF 1 R150 ERJ3GEYJ332 3.3k
C444 ECUV1H332KBV 0.0033 R152 ERJ3GEYJ332 3.3k
C449 ECUV1H105ZF 1 R159 ERJ3GEYJ680 68
R164 ERJ3GEYJ470 47
C450 ECUV1H105ZF 1 R165 ERJ3GEYJ470 47
C451 PQCUV1C105ZF 1 R166 ERJ3GEYJ332 3.3k
C452 PQCUV1C105ZF 1 R167 ERJ3GEYJ332 3.3k
C453 F2G1H1000010 10 R168 ERJ3GEYJ332 3.3k
C454 F2G1H1000010 10
C455 ERJ3GEY0R00 0(RESISTOR) R170 ERJ3GEYJ332 3.3k
R171 ERJ3GEYJ102 1k
C465 ECUV1C104ZFV 0.1 R172 ERJ3GEYJ103 10k
C466 ECUV1C104ZFV 0.1 R173 ERJ3GEYJ102 1k
R178 ERJ3GEYJ102 1k
R180 ERJ3GEYJ222 2.2k

(RESISTORS) R181 ERJ3GEYJ102 1k
R103 ERJ3GEYJ332 3.3k R182 ERJ3GEYJ223 22k
R104 ERJ3GEY0R00 0 R183 ERJ3GEYJ821 820
R105 ERJ3GEYJ471 470 R184 ERJ3GEYJ821 820
R189 ERJ3GEYJ101 100
R110 ERJ3GEY0R00 0
R119 ERJ3GEYJ220 22 R196 ERJ3GEYJ101 100
R120 ERJ3GEY0R00 0 R198 ERJ3GEYJ472 4.7k
R121 ERJ3GEY0R00 0 R199 ERJ3GEYJ102 1k
R122 ERJ3GEY0R00 0
R126 ERJ3GEYJ103 10k R206 ERJ3GEYJ330 33
R127 ERJ3GEYJ103 10k R207 ERJ3GEYJ105 1M
R129 ERJ3GEY0R00 0
R214 ERJ3GEYJ152 1.5k
R132 ERJ3GEYJ102 1k R236 ERJ3GEYJ562 5.6k
R134 ERJ3GEYJ103 10k R239 ERJ3GEYJ473 47k
R135 ERJ3GEY0R00 0
76
KX-TDA100BX
No. No.
R244 ERJ3GEYJ472 4.7k R458 ERJ3GEYJ472 4.7k
R248 ERJ3GEYJ105 1M R461 ERJ3GEYJ222 2.2k
R250 ERJ3GEYJ330 33 R463 ERJ3GEYJ473 47k
R251 ERJ3GEYJ104 100k R464 ERJ3GEY0R00 0
R465 ERJ3GEY0R00 0
R302 ERJ3GEYJ103 10k R468 ERJ3GEYJ106 10M


R421 ERJ3GEYJ106 10M R521 ERJ3GEYJ222 2.2k
R448 ERJ3GEYJ105 1M R568 ERJ3GEY0R00 0
R449 ERJ3GEYJ105 1M R569 ERJ3GEYJ103 10k
R450 ERJ3GEYJ823 82k J105 ERJ3GEYJ223 22k

R451 ERJ3GEYJ823 82k J109 ERJ3GEY0R00 0
R452 ERJ3GEYJ222 2.2k J110 ERJ3GEY0R00 0
R453 ERJ3GEYJ223 22k J113 PQ4R18XJ000 0
R454 ERJ3GEYJ222 2.2k J114 PQ4R18XJ000 0
77
KX-TDA100BX
No. No.
J115 PQ4R18XJ000 0 L115 ERJ3GEY0R00 0
J116 PQ4R18XJ000 0 L116 ERJ3GEY0R00 0
J121 ERJ3GEY0R00 0 L117 ERJ3GEY0R00 0
J129 ERJ3GEY0R00 0
L126 ERJ3GEY0R00 0
J213 ERJ3GEY0R00 0
L131 ERJ3GEY0R00 0
J331 ERJ3GEY0R00 0
L141 ERJ3GEY0R00 0
DIP02 ERJ3GEY0R00 0 L142 ERJ3GEY0R00 0
L143 ERJ3GEY0R00 0
(FILTERS ,COILS AND L144 ERJ3GEY0R00 0
RESISTORS) L145 ERJ3GEY0R00 0
FIL101 J0HAAH000003 CERAMIC FILTER L146 ERJ3GEY0R00 0
FIL102 J0HAAB000020 IC FILTER L147 ERJ3GEY0R00 0
FIL103 J0HAAH000003 CERAMIC FILTER L148 PFVF1B221SB CERAMIC FILTER
FIL106 J0HAAB000020 IC FILTER
FIL108 J0HAAB000020 IC FILTER L151 PFVF1B221SB CERAMIC FILTER
L153 PFVF1B221SB CERAMIC FILTER
FIL209 J0HAAH000003 CERAMIC FILTER
FIL401 G1BYYYC00007 COIL L166 PFVF1B221SB CERAMIC FILTER
L101 J0JCC0000042 COIL L170 PFVF1B221SB CERAMIC FILTER

L105 ERJ3GEY0R00 0 L173 PFVF1B221SB CERAMIC FILTER
L110 ERJ3GEY0R00 0 L183 PFVF1A471SG CERAMIC FILTER

78
KX-TDA100BX
No. No.
L186 PFVF1A471SG CERAMIC FILTER X101 PSVCC0025GT CRYSTAL OSCILLATOR
L187 PFVF1A471SG CERAMIC FILTER X102 PSVCC0019CT CRYSTAL OSCILLATOR
L189 PFVF1B470SB CERAMIC FILTER X103 H1B1635B0016 CRYSTAL OSCILLATOR
X201 H0J120500019 CRYSTAL OSCILLATOR
L190 PFVF1B470SB CERAMIC FILTER X202 H0J200500030 CRYSTAL OSCILLATOR
L191 PQ4R10XJ000 0
L192 PQ4R10XJ000 0 (OTHERS)
L193 PQ4R10XJ000 0 E1 PQDF996Z SHAFT
L194 PQ4R10XJ000 0 E2 PQHR10005Z SPACER
L195 PQ4R10XJ000 0 E3 PQUB14Z2 LEVER PA-V0
L196 PQ4R10XJ000 0 E4 PSGE1005Z COVER ABS-HB
E5 PSGE1006Z COVER ABS-HB
L211 ERJ3GEY0R00 0 E6 PSHD1088Z SCREW ABS-HB
L212 ERJ3GEY0R00 0 E7 PSHE1122Z SPACER
L213 ERJ3GEY0R00 0 E8 PSMH1208Z CHASSIS
L214 ERJ3GEY0R00 0 E9 PSUS1020Z SPRING
L215 ERJ3GEY0R00 0 E10 PSUS1021Y SPRING
L216 ERJ3GEY0R00 0 E11 XUC25VWV RETAINING RING
L217 ERJ3GEY0R00 0 E12 XYN3+F6 SCREW
L218 ERJ3GEY0R00 0
L219 ERJ3GEY0R00 0
18.4. BACK/LED BOARD PARTS
L220 ERJ3GEY0R00 0
L221 ERJ3GEY0R00 0 No.
L222 ERJ3GEY0R00 0 PCB2 PSWP2DA100AL BACK/LED BOARD ASS´Y (RTL)
L223 ERJ3GEY0R00 0
L224 ERJ3GEY0R00 0 (DIODES)
L225 ERJ3GEY0R00 0 LED201 LN316GP LED
L226 ERJ3GEY0R00 0 LED202 LN216RP LED
L227 PQ4R10XJ000 0
L228 PQ4R10XJ000 0 (CONNECTORS)
L229 PQ4R10XJ000 0 CN100 PSJS44A07Y CONNECTOR, 44P
L301 PQ4R10XJ000 0 CN103 K1KB90A00014 CONNECTOR, 90P
L401 G1A330G00004 COIL CN113 K1KA09B00077 CONNECTOR, 9P
L403 J0JHC0000035 CERAMIC FILTER CN114 PQJP3G38Z CONNECTOR, 3P
L405 PFVF1A471SG CERAMIC FILTER CN201 PQJP3D68Z CONNECTOR, 3P
L406 PFVF1A471SG CERAMIC FILTER
L407 PFVF1A471SG CERAMIC FILTER (CAPACITORS)
L408 PFVF1A471SG CERAMIC FILTER C101 PQCUV1A225ZF 2.2
L409 PFVF1A471SG CERAMIC FILTER C106 ECUV1C104ZFV 0.1
L413 PFVF2P600SG CERAMIC FILTER C111 ECUV1C104ZFV 0.1
L414 ERJ3GEY0R00 0
L415 ERJ3GEY0R00 0 C201 PQCUV1A225ZF 2.2
L416 ERJ3GEY0R00 0 C202 ECUV1C104ZFV 0.1
L421 ERJ3GEY0R00 0
(RESISTORS)
(FUSES) R101 ERJ3GEYJ103 10k
IP401 K5H502Z00003 FUSE R102 ERJ3GEYJ103 10k
IP402 K5H252Z00003 FUSE R105 ERJ3GEYJ103 10k
(BATTERY) R107 ERJ3GEYJ103 10k
BAT401 CR23541GUF LITHIUM BATTERY R108 ERJ3GEYJ103 10k
(SWITCHES)
SW101 EVQPF106K SWITCH R110 ERJ3GEYJ103 10k
SW103 PQSS2A26Y SWITCH
(CRYSTAL OSCILLATORS) R148 ERJ3GEYJ103 10k
79
KX-TDA100BX

No.






(FILTERS)

(OTHER)
E21 PSHR1276Z SPACER
18.5. FIXTURES AND TOOLS

No.
EC1 PSZZ1TDA100M EXTENSION BOARD (FOR CPU
CARD)
EC2 PSZZ2TDA100M EXTENSION BOARD (FOR LINE
CARD)
Note:
EC1 and EC2 are necessity for servicing.
80
KX-TDA100BX
19 FOR THE SCHEMATIC DIAGRAM

Note:
1. DC voltage measurements are taken with an oscilloscope or a tester with a ground.
2. The schematic diagrams and circuit board may be modified at any time with the development of new technology.
81
KX-TDA100BX
KX-TDA100 MPR CARD 1/5

(4)(5) (6)
A[0-25] A[0-25]
D[0-31]
LD[0-15]
IC127
A[25] 3 2
+3.3V
1 DG
+3.3V
IC125 IC125 D[31]
TP131
5 4 TP185 13
D31/PTB(7) A25 86 TP266 L122 TP349 5 4 TP375 A[25] A[23] 6 5
TP2027
RA102
RA111
nRD 12 11 9 8 1 20 6 3 6 3
nBACK 13 10 DIR VCC D[30]
TP132
7 2 TP186 14
D30/PTB(6) A24 84 TP267 L123 TP350 7 2 TP376 A[24] 4
0
TP2026 TP1008 8 1 8 1
19 18 LD[15] IC101
/2G B1 D[29]
TP133 TP187 15
D29/PTB(5) A23 82 TP268 L124 TP351 TP377 A[23] A[22] 8 9
D[15] TP1009
2 17 LD[14]
A1 B2 TP134 TP188 16 80 TP269 L125 TP352 TP378 A[22] 10
3.3V
D[28] D28/PTB(4) A22
C166
0.1u
D[14] TP1010
3 16 LD[13]
A2 B3 D[27]
TP135
5 4 TP189 17
D27/PTB(3) A21 78 TP270 L126 TP353 5 4 TP379 A[21] A[21] 11 12
RA103
RA112
D[13] TP1011 6 3 6 3
4 15 LD[12]
A3 B4 D[26]
TP136
7 2 TP190 18
D26/PTB(2) A20 77 TP271 L127 TP354 7 2 TP380 A[20] 13
0
D[12] TP1012 8 1 8 1
5 14 LD[11]
A4 B5 D[25]
TP137 TP191 20
D25/PTB(1) A19 76 TP272 L128 TP355 TP381 A[19] nBACK
D[11] TP1013
6 13 LD[10]
A5 B6 D[24]
TP138 TP192 22
D24/PTB(0) A18 75 TP273 L129 TP356 TP382 A[18]
D[10] TP1014
7 12 LD[9]
A6 B7 D[23]
TP139
5 4 TP193 23
D23/PTA(7) A17 74 TP274 L130 TP357 5 4 TP383 A[17]
RA104
RA113
D[9] TP1015 6 3 6 3
8 11 LD[8]
A7 B8 D[22]
TP140
7 2 TP194 24
D22/PTA(6) A16 73 TP275 L131 TP358 7 2 TP384 A[16]
0
D[8] 9 10 8 1 8 1
A8 GND D[21]
TP141 TP195 25
D21/PTA(5) A15 72 TP276 L132 TP359 TP385 A[15]
D[20]
TP142 TP196 26
D20/PTA(4) A14 70 TP277 L133 TP360 TP386 A[14]
IC123
+3.3V
D[19]
TP143
5 4 TP197 28
D19/PTA(3) A13 68 TP278 L134 TP361 5 4 TP387 A[13]
RA105
RA114
DG 6 3 6 3
D[18]
TP144
7 2 TP198 30
D18/PTA(2) A12 67 TP279 L135 TP362 7 2 TP388 A[12]
0
8 1 8 1
IC126 D[17]
TP145 TP199 31
D17/PTA(1) A11 66 TP280 L136 TP363 TP389 A[11]
nCS0 1
3 TP589 1 20
nCS4 2 IC126 DIR VCC D[16]
TP146 TP200 32
D16/PTA(0) A10 65 TP281 L137 TP364 TP390 A[10]
10 TP591
8 19 18 TP1000 LD[7]
IC126 9 /2G B1 D[15]
TP147
5 4 TP201 34
D15 A9 64 TP282 L138 TP365 5 4 TP391 A[9]
RA106
RA115
nCS5 4
6 D[7] 2 17 TP1001 LD[6] 6 3 6 3
nCS6 5 TP590 A1 B2 D[14]
TP148
7 2 TP202 36
D14 A8 63 TP283 L139 TP366 7 2 TP392 A[8]
C167
0
0.1u
D[6] 3 16 TP1002 LD[5] 8 1 8 1

A2 B3 D[13]
TP149 TP203 37
D13 A7 62 TP284 L140 TP367 TP393 A[7]
D[5] 4 15 TP1003 LD[4]
+3.3V A3 B4 D[12]
TP150 TP204 38
D12 A6 61 TP285 L141 TP368 TP394 A[6]
D[4] 5 14 TP1004 LD[3]
A4 B5 D[11]
TP151
5 4 TP205 39
D11 A5 60 TP286 L142 TP369 5 4 TP395 A[5]
RA107
RA116
D[3] 6 13 TP1005 LD[2] 6 3 6 3
A5 B6 D[10]
TP152
7 2 TP206 40
D10 A4 58 TP287 L143 TP370 7 2 TP396 A[4]
0
0
D[2] 7 12 TP1006 LD[1] 8 1 8 1
A6 B7 TP153 TP207 41 56 TP288 L144 TP371 TP397
C161
14 D[9] A[3]
D9
0.1u
IC126 A3
D[1] 8 11 TP1007 LD[0]
7
A7 B8 D[8]
TP154 TP208 42
D8 A2 55 TP289 L145 TP372 TP398 A[2]
D[0] 9 10
A8 GND D[7]
TP155
5 4 TP209 43
D7 A1 54 TP290 L146 TP373 R135 0 TP399 A[1]
RA108
6 3
D[6]
TP156
7 2 TP210 44
D6 A0 53 TP291 L147 TP374 R136 0 TP400 A[0]
IC124
0
+3.3V_CPU TP157 8 1
+3.3V TP211 46
D[5] D5
DG DG
TP158 TP212 48 8 TP292 nIRQ_ASIC
1.9VB D[4] D4 IRQ0/#IRL0/PTH(0)
TP159 TP213 49 9 TP293 nIRQ_USB
R555
D[3] 5 4 IRQ1/#IRL1/PTH(1)
3 TP572 L103 D3
10K
RA109
21 VCC-IO VCC-RTC 6 3
TP160 TP214 50 10 TP294 nIRQ_SDB
D[2] 7 2 D2
0.1u
1.0u
2.2u
IRQ2/#IRL2/PTH(2)
0
35 VCC-IO 8 1
SW107 TP161
1 2 D[1] TP215 51
D1 IRQ3/#IRL3/PTH(3) 11 TP295 nLOS
+3.3V 47 VCC-IO
C116
C121
C126
1.8V TP162 TP216 52 12 TP296 nDC_ALM

D[0] D0 IRQ4/PTH(4)
59 VCC-IO VSS-RTC 6
DG
L194
NMI 7 TP297 NMI

71 VCC-IO +3.3V
DG TP110 R106 0
nCS0 TP217 96
#CS0/#MCS(0) #IRQ0UT 160 TP298 nIRQOUT
85 VCC-IO R506 10K
TP111 R107 0 TP163 L105 TP218 98 182 TP299 nLOS
nCS2 #CS2/PTK(0)
L195
J152 97 29 R507 10K #WAKEUP/PTD(3)

VCC-IO VCC-1.8 +3.3V
TP112 R108 0 TP164 L106 TP219 99
NC nCS3 #CS3/PTK(1) R138
FIL101 TP571 111 VCC-IO VCC-1.8 81 R508 10K
3 1 J153 TP113 R109 0 TP165 L107 TP220 100 159 TP300 10K RING_SYNC
TP573 nCS4 #CS4/PTK(2) TCLK/PTH(7)
163 VCC-IO VCC-1.8 134 R509 10K
NC TP114 R110 0 TP221 101
2 FIL104 nCS5 #CS5/#CE1A/PTK(3)
2.2u
1.0u
183 VCC-IO VCC-1.8 154 1 3 R510 10K

TP115 R111 0 TP222 102 191 TP301 nDREQ0
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
nCS6 #CS6/#CE1B #DREQ0/PTD(4)

VCC-1.8 175 2 R511 10K
0.1u
C125 0.1u
C130 1.0u
C131 2.2u
C133 2.2u
C134 2.2u
TP116 R112 0 TP166 L108 TP223 87 115 TP302 nDACK1

C119 0.1u
C101
C102
nBS #BS/PTK(4) #DACK1/PTD(7)

R512 10K
C103
C104
C106
C107
C108
C110
C111
C112
TP117 R113 0 TP167 L109 TP224 118 192 TP303 nDREQ1

nRAS3U #RAS3U/PTE(2) #DREQ1/PTD(6)
19
C120
VSS-IO
TP118 R114 0 TP168 L110 TP225 106 114 TP304 nDACK0
nRAS3L #RAS3L/PTJ(0) #DACK0/PTD(5)
33 VSS-IO VSS-1.8 27
PTE[1] TP226 119
#RAS2U/PTE(1) DRAK0/PTD(1) 189 TP305 nLEDALM
45 VSS-IO VSS-1.8 79
nFAN_ALM TP227 107 190 TP306 nLEDRUN
(3)
#RAS2L/PTJ(1) DRAK1/PTD(0)
57 VSS-IO VSS-1.8 132
TP121 R117 0 TP171 L113 TP228 108
nCASL #CASSLL/CASL/PTJ(2)
69 VSS-IO VSS-1.8 152
TP122 R118 0 TP172 L114 TP229 110 171 TP307 RXD0
nCASU #CASLH/CASU/PTJ(3) RxD0/SCPT(0)
83 VSS-IO VSS-1.8 153
POWTYPE[0] TP230 112
#CASHL/PTJ(4) TxD0/SCPT(0) 164 TP308 TXD0
95 VSS-IO VSS-1.8 173
POWTYPE[1] TP231 113
#CASHH/PTJ(5) SOK0/SCPT(1) 165 TP309 MASTER/nS
109 VSS-IO
DG TP232 116 172 TP310 RXD1
#CAS2L/PTE(6) RxD1/SCPT(2)
161 VSS-IO
TP574 L101 nPRS_RMT TP233 117
#CAS2H/PTE(3) TxD1/SCPT(2) 166 TP311 TXD1
(2)
181 VSS-IO VCC-PLL1 145 +3.3V_CPU
TP123 R11922 TP173 L115 TP234 89 167 TP312
DQMLL(nWE0) M/nS
C122 0.1u
C127 1.0u
R513 10K #WE0/DQMLL SCK1/SCPT(3)

2.2u
C117
DG TP124 R120 0 TP174 L116 TP235 90 174 TP313 RXD2

+3.3V DQMLU(nWE1) #WE1/DQMLU/#WE RxD2/SCPT(4)
R514 10K
TP125 R121 0 TP175 L117 TP236 91 168 TP314 TXD2
DQMUL(nWE2) #WE2/DQMUL/#ICIORD/PTK(6) TxD2/SCPT(4)
RESET SW
205 VCC-A3.3 VSS-PLL1 147 R515 10K

TP126 R122 0 TP176 L118 TP237 92 169 TP315 nWDTST
DQMUU(nWE3) #WE3/DQMUU/#ICIOWR/PTK(7) SCK2/SCPT(5)
R516 10K
DG
C105
TP127 R123 0 TP177 L119 TP238 93 170 TP316 nRTS2

0.1u
RD/nWR RD/#WR #RTS2/SCPT(6)

R517 10K
TP128 R124 0 TP178 L120 TP239 88 176 TP317 nCTS2
TP575 L102 nRD #RD #CTS2/IRQ5/SCP(7)
198 VSS-A3.3 VCC-PLL2 150 R518 10K
TP129 R125 0 TP179 L121 TP240 105
CKE
C128 1.0u
C123 0.1u
2.2u
208 VSS-A3.3 CKE/PTK(5)

+3.3V
C118
nWAIT TP241 123

#WAIT #CE2B/PTE(5) 104 TP318 nPRS_SDB
1
R103 NC
DG R523 0 SW106 #IOIS16/PTG(7) 126 TP319 FSEL0
VSS-PLL2 148 3.3K +3.3V C137
1 2
J158 FIL105 470P TP242 149
CAP2 #CE2A/PTE(4) 103 TP320 nPRS_MEX
16.384M C455 R104
R570
NC CKIO 3 1
NC
IC101 DG R102 2 C138 TP243 146

NC TP130 0 0 CAP1
TP109 470P TP244
TP102 J101 NC DG DG 156 EXTAL #MCS(0)/PTC(0)/PINT(0) 188 TP321 nRTS1
NC TP105 FIL102 SCLK TP245 155 187 TP322 nCTS1
1 3 XTAL #MCS(1)/PTC(1)/PINT(1)
2 DTR1
+3.3V 162 CKIO 186 TP323
TP103 C135 TP184 #MCS(2)/PTC(2)/PINT(2) DSR1
J102
SW101
DG DTR2
5 185 TP324
+3.3V
NC J154 L196 22P EXTAL2 #MCS(3)/PTC(3)/PINT(3) DSR2

TP246
2
1
X102
TP108 DCD2
IC103
NC 1
M/R VCC
5
XTAL 4 XTAL2 #MCS(4)/PTC(4)/PINT(4) 180 TP325 DSR_RMT
MA110TX
C109 TP106 FIL103

RESET
1 +3.3V
2
R105
1 3 R131 0 179 TP326

3
4
2 C136
470
Xin VDD nRESOUT

D102
#MCS(5)/PTC(5)/PINT(5)
16.384MHz
12P 7 SUB
8 2 22P TP183 TP247 TP265
X101
3 4 178 TP327
C129
Xout FRSEL
C132
193 #RESETP
C124
#MCS(6)/PTC(6)/PINT(6)
0.1u
1.0u
2.2u
6 GNDVOUT DG
4
R127
R126
10K
10K
20 SCHEMATIC DIAGRAM
0V
TP248 124 177 TP328 +3.3V

AT
S0 SSCLK IC107 #RESETM #MCS(7)/PTC(7)/PINT(7)

C114 5 DG
3 nRESET
R137
S1 VSS TP249 122 184 TP329

10K
12P 2 nRESETM #BREQ #RESETOUT/PTD(2)

+3.3V NMI nBREQ
DG DG
R1290
TP250 121
#BACK TDO/PTE(0) 120 TP330 TDOA
nRESET nBACK
TP2028 TP2029 +3.3V NC IC206 TP251 144 94 TP331 nAUDSYNC
TP180 SW105 MD0 #AUDSYNC/PTE(7)
QA102 NC 10 1 2
J122
J124
R552
5
NC
1 TP252 1 143 TP332

NC
NC
9 Q
PR D 12 MD0 NC MD1 #IRLS(0)/PTF(0)/PINT(8) nBATT
IC130 +3.3V MD1 nBAT_ALM
2 1 TP598 2 TP599 MD2 TP253 2
MD2 #IRLS(1)/PTF(1)/PINT(9) 142 TP333 nAC_ALM
nDC_ALM
C172
NC 3 DG 8 Q CK 11 +3.3V 195 MD3 141 TP334

22K
#IRLS(2)PTF(2)/PINT(10)
NC
NC
NC
+3.3V +3.3V +3.3V

NC
4
R502
CLR
0
0
10K
J121
J105
J107
J109
0
0
J123
J106
J108
J110
R550 C173 13 196 MD4 #IRLS(3)/PTF(3)PINT(11) 140

IC130 TP597 DG TP600 DG
10K
10K
10K
R557
R558
NC +3.3V
R559
4 3 NC 197 MD5 139 TP336

TCK/PTF(4)/PNT(12)
(1)
TP596 NC R551
C171
DG NC DG DG TP254 194 CA 138 TP337

NC
TDI/PTF(5)/PINT(13)
TCK
TP181 R128 1K TP255 157 137 TP338
GAIN0 STATUS0/PTJ(6) TMS/PTF(6)/PINT(14) TDI
DG nWDTST TP182
TMS
R130 1K TP256 158 136 TP339 nTRST
WDTCLR GAIN1 STATUS1/PTJ(7) #TRST/PTF(7)/PINT(15)
R134
135 TP340
10K
10K
R556
AUDATA(0)/PTG(0)
10K +3.3V TP257 199 133 TP341
RA101 AN(0)/PTL(0) AUDATA(1)/PTG(1) DG DG MEX_MODE[0]
1 10 TP258 200 131 TP342 MEX_MODE[1]
2 9 AN(1)/PTL(1) AUDATA(2)/PTG(2)
MEX_MODE[2]
3 8 TP259 201 130 TP343 MEX_MODE[3]
+3.3V 4 7 AN(2)/PTL(2) AUDATA(3)/PTG(3)
J113
5 6 TP260 202 129 TP344 nINIT
0 AN(3)/PTL(3) PTG(04)
DIPSW0
DIPSW1 TP261 203
AN(4)/PTL(4) #ASEBRKAK/PTG(5) 128 TP345 nASEBRKAK
J114 DIPSW2
TP262 204 127 TP346 nASEMDO
20.1. MPR CARD
0 DIPSW3 AN(5)/PTL(5) #ASEMD0/PTG(6)

DIPSW4
14 DIPSW5 TP263 206
AN(6)/DA(1)/PTL(6) #ADTRG/PTH(5) 125 TP347 VBUS
J115
C170
0.1u
IC125 DIPSW6
0 DIPSW7 TP264 207
AN(7)/DA(0)/PTL(7) AUDCK/PTH(6) 151 TP348 +3.3V
7 SW102 NC AUDCK
DIP00 NC
R132
1 9
1K
J116 +3.3V
2 10 DIP01 NC
0 3 11 DIP02 0
R525
10K
4 12 DIP03 NC
1.8K
DIP04 NC
R133
5 13
6 14 DIP05 NC
FG DG 7 15 DIP06 NC
DG 8 16 DIP07 NC
DG
DG DG
82
KX-TDA100BX

(4)(5) (6)
CN103
L178 NC
+3.3V_ASIC +3.3V +3.3V A1 (+15VPT)
FIL108
IC102 1 3 B1 (+15VPT)
R503
R504
680
680
2 TP504 R144 EC_CLK 10K
A[20] 119 ADD[20] 111 TP467 47 EC_CLK RA133 +3.3V
EC_CLK R161 R172 C175 A2 (+40V)
A[19] 120 109 TP468 DG R192 22 EC_nSTOP 1 10
ADD[19] EC_STOP
A[18] 121 108 TP469 R193 22 EC_nTRDY 2 9
ADD[18] EC_TRDY DG N.C. 10K NC +15VIN +15VIN B2 +15V
A[17] 122 107 TP470 R194 22 EC_nPERR DG 3 8
ADD[17] EC_PERR EC_nSTOP 4 7
A[16] 123 106 TP471 L148 TP505 R553 68EC_nFRAME EC_nTRDY A3 POWERGND
ADD[16] EC_FRAME 5 4 5 6
A[15] 125 TP472 L149 TP506 EC_nPERR
RA123
ADD[15] EC_PAR 103 6 3 EC_PAR B3
DG
POWERGND
A[14] 126 102 TP473 L150 TP507 P.G
68
ADD[14] EC_BE[0] 7 2 EC_nCBE[0] EC_PAR
A[13] 127 101 TP474 L151 TP508 8 1 EC_nCBE[1] EC_nCBE[0] EC_CLK A4 EC_CLK
ADD[13] EC_BE[1]
A[12] 128 100 TP475 EC_nRST EC_nCBE[1]
ADD[12] EC_nRST EC_nSTOP B4 EC_nSTOP
A[11] 129 +3.3V
ADD[11]
A[10] 130 98 TP476 L152 TP509 5 4 EC_AD[0] A5 GND
ADD[10] EC_AD[0]
RA124
R554
10K
A[9] 131 97 TP477 L153 TP510 6 3 EC_AD[1]
ADD[9] EC_AD[1]
68
96 TP478 L154 TP511 7 2 EC_AD[2] B5 GND
A[8] 132 ADD[8] EC_AD[2] 8 1 EC_AD[3] DG
A[7] 135 95 TP479 L155 TP512 EC_nFRAME
ADD[7] EC_AD[3] EC_nTRDY A6 EC_nTRDY
A[6] 136 92 TP480 L156 TP513 5 4 EC_AD[4]
ADD[6] EC_AD[4]
RA125
A[5] 137 91 TP481 L157 TP514 6 3 EC_AD[5] EC_nPERR B6 EC_nPERR
ADD[5] EC_AD[5] EC_nRST
68
7 2 EC_AD[6]
A[4] 138 ADD[4] EC_AD[6] 90 TP482 L158 TP515
8 1 EC_AD[7] R158 R171 +3.3V
+3.3V TP483 TP516 10K EC_nFRAME A7 EC_nFRAME
A[3] 139 ADD[3] EC_AD[7] 89 L159 +3.3V
A[2] 87 TP484 L160 TP517 5 4 EC_AD[8] DG N.C. 1K RA134
140 ADD[2] EC_AD[8] 1 EC_PAR B7 EC_PAR
RA126
6 3 10
A[1] 141 86 TP485 L161 TP518 EC_AD[9] 2 9
ADD[1] EC_AD[9]
68
85 TP486 L162 TP519 7 2 EC_AD[10] EC_AD[0] 3 EC_nCBE[0] A8 EC_nCBE[0]
A[0] 142 ADD[0] EC_AD[10] 8 1
8
EC_AD[11] EC_AD[1] 4 7
84 TP487 L163 TP520 EC_AD[2]
EC_AD[11] 5 6 EC_nCBE[1] B8 EC_nCBE[1]
LD[15] 144 81 TP488 L164 TP521 5 4 EC_AD[12] EC_AD[3]
DATA[15] EC_AD[12]
C162
14
RA127
EC_nRST
0.1u
IC127 LD[14] 145 80 TP489 L165 TP522 6 3 EC_AD[13] EC_AD[4] A9 (EC_IDSEL)

DATA[14] EC_AD[13]
68
79 TP490 L166 TP523 7 2 EC_AD[14] EC_AD[5]
LD[13] 146 DATA[13] EC_AD[14] 8 1 13 R197 B9
7 EC_AD[15] EC_AD[6] nRESOUT 11 EC_nRST
LD[12] 147 78 TP491 L167 TP524 EC_AD[7] 12
DATA[12] EC_AD[15] 100
LD[11] 148 DATA[11] IC126 A10 GND
TP492 R195 100 EC_nINT
LD[10] 149 DATA[10] EC_INT 76 B10
TP493 R196 100 EC_nCDET GND
LD[9] 150 DATA[9] EC_CDET 75 DG
LD[8] 151 DATA[8] 10K EC_AD[0] A11 EC_AD[0]
LD[7] 154 65 TP494 L168 TP525 5 4 CT_D[0] RA135 +3.3V
DG DATA[7] CT_D[0]
RA128
LD[6] 155 64 TP495 L169 TP526 6 3 CT_D[1] 1 10 EC_AD[1] B11 EC_AD[1]

DATA[6] CT_D[1]
47
63 TP496 L170 TP527 7 2 CT_D[2] 2 9

LD[5] 156 DATA[5] CT_D[2] 8 1 CT_D[3] EC_AD[8]
TP497 TP528 3 8 EC_AD[2] A12 EC_AD[2]
LD[4] 157 DATA[4] CT_D[3] 62 L171 EC_AD[9] 4 7
LD[3] 158 58 TP498 L172 TP529 5 4 CT_D[4] EC_AD[10] 5 6 EC_AD[3] B12
DATA[3] CT_D[4] EC_AD[3]
RA129
nBS +3.3V 57 TP499 L173 TP530 6 3 CT_D[5] EC_AD[11]

LD[2] 159 DATA[2] CT_D[5] EC_AD[12]
47
56 TP500 L174 TP531 7 2 CT_D[6] EC_AD[4] A13 EC_AD[4]

LD[1] 160 DATA[1] CT_D[6] 8 1 CT_D[7] EC_AD[13]
R526
TP501 TP532
2
1
LD[0] 161 DATA[0] CT_D[7] 55 L175 EC_AD[14] B13

IC125
10K
EC_AD[15] EC_AD[5] EC_AD[5]

+3.3V +3.3V
R569
TP533 +3.3V A14

163 nEXTINT[2] CT_NETREF 53 CT_NETREF GND
10K
nCS5
3
TP502 L176 TP534 R145 47

164 nEXTINT[1] CT_C8 52 CT_C8 R162 R173
B14
11
TP503 L177 TP535 R146 68CT_FRAME GND

165 nEXTINT[0] CT_FRAME 51 N.C. 1K DG
IC131
nIRQ_ASIC 166 EC_AD[6] A15 EC_AD[6]

nIRQ +3.3V +3.3V R163 R174
nBREQ 167 nBREQ RINGER 50 RINGER B15
nBACK N.C. 1K EC_AD[7] EC_AD[7]
10
168 nBACK DG
R563
10K
R505
nCS4
4
5
10K
169 nCS_SRAM TCK 68 TCK EC_nINT

IC125
EC_AD[8] A16 EC_AD[8]

nCS5 170 69 TDOA EC_nCDET
nCS_MES TDI
nRD 173 70 TP585 EC_AD[9] B16 EC_AD[9]
nRD TDO
DQMLU(nWE1) 71
R566 6
174 nWR[1] TMS TMS

DQMLL(nWE0) J134 EC_AD[10] A17 EC_AD[10]
72 nTRST
22
175 nWR[0] TRST +3.3V

nWAIT 176 J155 NC EC_AD[11] B17 EC_AD[11]
nBUSY TP466
nRESET 0
177 nRESET PLLATI 46 J125 TP536 J159 J161 A18
L191
TP2030 GND
R567
178 nBS PLLCLK 45 16.384M IC131
NC
J163
CKIO 179 NC NC FIL111 R565 DG B18

NC
J126
CLKIO 8 J160 SHW_CLK

R143
2 4 9 IC111 TP567 nSHW_CLK

4
VREF_PLUS 40 +3.3V 1 3
0
0 J162
33
IC132 NC 9 8 TP2079 100

PLLCLK
R562
A19
C159
C160
LUHW[1] 187 LUHW[1] VREF_MINUS 41 0 IC110 14 EC_AD[12] EC_AD[12]

0.1u
1.0u
X103 2
LUHW[0] 185 R524 DG 4 1
10K
LUHW[0] VCC N.C EC_AD[13] B19 EC_AD[13]

TP594
LDHW[1] 188 LDHW[1] TESTMODE0 73 DG NC IC111 IC111
7
R199 C168
LDHW[0] 186 LDHW[0] TESTMODE1 74 TP537 3 2 EC_AD[14] A20 EC_AD[14]
/RECEIVER
3 1 4 3 2 1 OUTGND
J127
R140 TP401FIL106 TP405

LHWCLK[0] 183 HW_CLK[1] TP2031 2 1K 16.384MHz DG
1
NC
TP538 TP592 1000p EC_AD[15] B20 EC_AD[15]

33 3 2TP403 182
TP406
HW_CLK[0] PLLVDD 44 FIL110
R501 TP593 X104
184 DG 4 1
RS232C
DRIVER
HW_FH VCC NC
EC_nINT A21 EC_nINT
DG 10K
189 L_NETREF PLLGND 43 DG TP595 10 NC 5
NC 6
SHW_CLKR142 TP407 192 C169 9 NC EC_nCDET B21 EC_nCDET
33 SHW_CLK TP2032 NC
8
SHW_FH 193 SHW_FH AVDD 31 J135 NC NC NC 7 A22 GND
J128
Master/Slave_SW AVDD 42 NC
+3.3V 3
OUT GND
2
IC131
DG NC R564 DG B22
TXD_RMT 115 SDI SHW_FH nSHW_FH
J129
TP576
FIL107 L192 NC
RXD_RMT 11
0
SW104 116 SDO VDD 1 3 5 6 TP2078 100

CT_D[0] A23 CT_D[0]
NC
RTS_RMT 117 VDD 30 0

C139
C140
C143
RTS
0.1u
1.0u
2.2u
2
+3.3V CTS_RMT 118 CTS VDD 49 DG IC120 CT_D[1] B23 CT_D[1]
1
2
3
2 3
VDD 60 TXD2
TP335
R198
4.7K
DG TP408 203 C_CS[3] VDD 67 CT_D[2] A24 CT_D[2]

(3)
+5V
TP409 204 C_CS[2] VDD 83 DG +3.3V
CT_D[3] B24 CT_D[3]
R166
VDD 94
3.3K
TP410 205 C_CS[1]

+3.3V R529 TP2037 IC121
TP411 206 C_CS[0] VDD 105 R155 CT_D[4] A25
L193
RXD2 3 1 CT_D[4]
10K R530 R527 22 L189
TP412 207 DCLK VDD 114
0
R151
3.3K
10K L190 1.8K TP547 2 CT_D[5] B25 CT_D[5]

R531 R528 22
10K
TP413 208 DOUT VDD 134 +3.3V_ASIC
R532 TP2038
10K
TP402 209 DIN VDD 153 J136 CT_D[6] A26 CT_D[6]
J156 DG
210 CP[0] VDD 172
IC120
TP2040
NC NC B26
TP414 VDD 191 nRTS2 4
6
CT_D[7] CT_D[7]
DCLK_RMT TP2039
R549 HALT 194

HALT PIO[7]/CHP[7] VDD 212 TP577 FIL109 5
A27 GND
Mu/nA 195 PIO[6]/CHP[6] VDD 231 1 3 +5V
(2)
10K
MOHSEL 196 PIO[5]/CHP[5] MASTER/nS R568 DG B27 Reserved_B27
TP448
R167
2
3.3K
DOUT_RMT
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
1.0u
2.2u
J120 MELODYSEL 197 PIO[4]/CHP[4] N.C. 47 IC121 0

DIN_RMT
TP415 198 J131 R156 CT_NETREF R191 22 A28 CT_NETREF

WDTCLR N.C. 112 nCTS2 6 4
C_CS[0]
NC PIO[3]/CHP[3]
J157 TP2074
R152
CH_SEL[2] 199
3.3K
PIO[2]/CHP[2] 0 1.8K TP548 5 B28

C141
C142
C144
C145
C146
C147
C148
C149
C150
C151
DG TP449 CT_C8 CT_C8

0 200
CH_SEL[1] PIO[1]/CHP[1] GND 1
CH_SEL[0] 201 PIO[0]/CHP[0] GND 10 DG CT_FRAME A29 CT_FRAME
GND 20 IC120 +3.3V B29 nLOS
32 DTR2 10
RX[7] GND 29
J130
+3.3V 8
0
9
R181
33 GND 48
1.0K
RX[6] R179 A30 GND

R560
34 +5V
RX[5] GND 54 2.2K
NC
DG nLOS B30
35 DG GND
RX[4] GND 59 DG
R170
3.3K
CKIO 36 IC121 TP560 R183

RX[3] GND 61 DSR2 R175 8 10 820 A31 TXD1
37 RX[2] GND 66
R561
NC
TP561 R184
R153
3.3K
38 1.8K +5V TP549 9 820 B31

RX[1] GND 77 RXD1
39 RX[0] GND 82 TP562 R185
R168
3.3K
+3.3V RA117 820 A32 RS1

DG
DG 10K 10 1 DG GND 88 R157 IC121
TP563 R186
TP416 DCD2 11 13
213 P0[7] GND 93 820 B32
3
9 2 CS1
R150
3.3K
TP417 1.8K TP550 12

8 3 214 P0[6] GND 99 TP564 R187
820
TP418 A33 ER1
7 4 215 P0[5] GND 104 IC120
6 5 TP419 13 TP565 R188
216 P0[4] GND 110 12
11 DG
R165
820 B33 DR1
TP420 QA101
217 P0[3] GND 113 nLEDRUN 1 5 IC131 TP566 R189100 A34
TP421 LDHW[1]
218 P0[2] GND 124 +3.3V TP542 47 nLDHW[1]
TP422 1 2
219 P0[1] GND 133 2
LUHW[1] TP2077 R190100 B34 nLUHW[1]
SD ACCESS LED
TP423
+3.3V RA118
220 P0[0] GND 143 nLEDALM 3 4 3
TP541 R159 TP578 IC131 L183
10K 10 GND 152 4 LEDRUN A35 LEDRUN
R148
1
TP424 222 P1[7]/TXA[7] GND 162 68 L184
10K
9 2 QA103 TP579
TP425 223 LEDALM B35 LEDALM
8 3 P1[6]/TXA[6] GND 171 1 5
TP426 224 +3.3V +3.3V
7 4 P1[5]/TXA[5] GND 180 R164 LED101 A36 nBATT
6 5
R182
TP427 225 DG 2
P1[4]/TXA[4] GND 181
22K
TP428 226 P1[3]/TXA[3] GND 190 47 TP544 1 2 nBATT R180

B36 DCD1
TP429 nPRS_SDB 3 Green DG
227 P1[2]/TXA[2] GND 202 4 +3.3V
TP430 2.2K R519 A37 nFAN_ALM
228 P1[1]/TXA[1] GND 211 LED103 TP580R176
TP431 229 820
+3.3V RA119
P1[0]/TXA[0] GND 221 nBAT_ALM TP586 M/nS B37 M/nS
+3.3V
2 1
10K 10 1 GND 230 Red
680 1.0K
TP432 232 A38 (+30V)
9 2 P2[7] GND 240 +3.3V R521
TP433 233 10K RA121 +3.3V nFAN_ALM R520
R522
8 3 P2[6] B38
1.0K
TP450 1 10 (+30V)
TP434 234
7 4 P2[5] P4[7] 12 2 9 2.2K L185
6 5 TP435 235 TP451 A39
P2[4] P4[6] 13 3 8 TP539 C RINGER
TP436 236 TP452 B IC110 IC110
P2[3] P4[5] 14 4 7 RINGER
RING_SYNC 13 12 11 10
L186 B39 RING_SYNC
TP437 237 P2[2] 15 TP453 5 6 Q101
P4[4] IC110 TP583 L187
TP438 TP454 HALT TP556
BATTERT
+3.3V 238 P2[1] P4[3] 16 E 1 2 A40 nHALT

TP439 239 TP455
P2[0] P4[2] 17
R178
+3.3V DG TP584 TP557

R139
RA120 B40
ALARM
10K
SW103 2 TP456 RING_SIN

P4[1] 18
10K
10K 10
(1)
1 TP440 TP457
1 2
2 P3[7]/TXB[7] P4[0] 19 A41
9 GND
3 TP404 8 3 TP441 3 P3[6]/TXB[6] 10K RA122 +3.3V
DG
LED
TP458
5
TP442 1 10 DG B41
7 4 4 P3[5]/TXB[5] P5[7] 21 2 3.3V_BB +3.3V
5 9
6 TP443 5 TP459
P5[6] 22
6
DG P3[4]/TXB[4] 3 8
System-Initialize_SW TP444 TP460 A42 DC_ALM
6 P3[3]/TXB[3] P5[5] 23 4 7 TP2033 +3.3V
TP445 7 P3[2]/TXB[2] 24 TP461 5 6 B42
RA137
P5[4] AC_ALM
TP446 8 TP462 IC111 IC110
P5[3] 25
5
6
7
8
P3[1]/TXB[1] 6 5 TP559
10K
J132
J133
NC
12 13 nDC_ALM 4 3 A43
0
TP447 9 TP463 POWTYPE[0]

P3[0]/TXB[0] P5[2] 26
TP464 IC131
P5[1] 27 nAC_ALM 6 5 TP570 B43
4
3
2
1
DG IC111 RA136 POWTYPE[1]

TP465
P5[0] 28 12 13 IC110 1 8
2 7 A44 (DIAG_R)
POWTYPE[0] 3 6
IC111 POWTYPE[1] 4 5 B44 (DIAG_T)
10 11
C157 1000P
C156 1000P
2.2K
A45 GND
+3.3V IC111 DG B45 (RINGER_AC)
8 9
+3.3V
+3.3V +3.3V
DG
DG DG
IC130
5 6
IC132 5
C174
14 IC130
C466
0.1u
IC130 1
0.1u
C465
C163
9 8 14 14
0.1u
0.1u
NC IC130 NC IC131 IC110

7 11 10
7 7 3
IC130
13 12
DG
DG DG
DG DG
83
A[0-25] A[0-25] A[0-25]
A[0-25]
KX-TDA100BX
D[0-31]
CN210
NC NC J201
IC203 TP663
2 L203 TP643R228 1
LD[0-15] DO1+ TP664
TP678 TP635 0 TP651 1 2 FIL203 2
SHW_CLK 1
LA[1-16] DI1 NC TP665
3 L204 TP644R229 TP652 4 3 3
+3.3V +3.3V DO1- TP666
TP636 0 J202
4
IC205 NC TP667
LA[1-16]
3.3V IC2064 NC LA[1] 47 MNA1 MND0
18 LD[0] J203 5
LA[2] 46 17 LD[1] NC NC TP668
IC201 2 D PR Q 5 MNA2 MND1
LA[3] 45 16 LD[2] 6 L205 TP645R230 6
TP657 MNA3 MND2 DO2+
A[23] 1 15 nCS_USB TP2036 LA[4] 44 MNA4 MND3
15 LD[3]
A Y0 43 TP679 TP637 0 TP653 1 2 7
LA[5] MNA5 MND4
14 LD[4] SHW_FH 7
A[24] 2 14 nCS_SDB0 TP658 CKIO J217 3 CK Q 6 LA[6] 42 13 LD[5] DI2 NC FIL204
B Y1 MNA6 MND5 L206
CLR LA[7] 41 12 LD[6] 5 TP646R231 TP654 4 3 8
TP605 NC MNA7 MND6 MASTER/nS DO2-
A[25] 3 13 nCS_SDB1 +3.3V 1 MND7
11 LD[7] 4 J204 TP669
C Y2 TP638
NC
10 LD[8] EN1/2 0 9
J215
1 20 MND8 NC
12 nCS_SDB0 19 9 LD[9]
0.1u
DIR VCC TP670
C216
Y3 TP606 XMNCS MND9
+3.3V nRD 48 XMNRE MND10
8 LD[10] J205 10
19 /2G B1 18 A[16] 11 nWE 1 7 LD[11] NC NC
TP2016 Y4 TP607 XMNWEMND11
DG 23 6 LD[12] 10 L207 TP647R232 11
LA[16]TP2072 TP2056 L226 2 17 A[15] XMNDK MND12 DO3+
A1 B2 1 2 6 10 TP608 TP2080 MND13
5 LD[13]
G1 Y5 TP680 TP639 0 TP655 1 2 FIL205 12
5 4 TP2055 L225 TP2015 +3.3VB +3.3VB MND14
4 LD[14] LDHW[1] 9
LA[15]TP2071 3 B3 16 A[14] 4 9 IC311 24 3 LD[15] DI3 NC
6 3 A2 DG 3 4 DG G2A Y6 TP609 13 XMNIRQMND15 L208
7 2 +3.3V nIRQ_SDB 11 11 TP648R233 TP656 4 3 13
TP2054 L224 TP2014
22
LA[14]TP2070 4 15 A[13] 5 12 DO3-
RA207
8 1 A3 B4 6 TP694 nCS6 7 TP610 25 XMNIRQ2 J206
5 G2B Y7 TP640 0
TP2053 L223 TP2013 14
NC
NC
LA[13]TP2069 5 A4 B5 14 A[12]
J227
D[31] 7 8 D[30] SDCLK
TP2052 L222 TP2012 21 MCLK SDDAT0
29 SDDAT0
LA[12]TP2068 6 A5 B6 13 A[11] TP1022 R249 nRESET 2 28 SDDAT1
D[29] 9 10 D[28] XRST SDDAT1 FG
5 4 TP2051 L221 TP2011 +3.3V SDDAT2
35 SDDAT2 14
LA[11]TP2067 7 A6 B7 12 A[10] IC209 TP2034 NC 34 SDDAT3 DO4+ TP617
6 3 D[27] 11 12 D[26] R250 J216 SDDAT3 +3.3V
7 2 1 2 3 4 1 3 J222 15
TP2050 L220 TP2010
22
LA[10]TP2066 8 11 A[9] DI4
RA206
8 1 A7 B8 D[25] D[24] 2 22 VDD SDCD
27 SDCD
L227
13 14 IC209 TP1023 33 TP20350
TP2049 L219 TP2009 FIL208 FIL207 30 VDD SDCMD
33 SDCMD 13
LA[9] TP2065 9 10 3 1 TP1019 36 31 SDCLK DO4- TP618
A8 GND D[23] 15 16 D[22] TP2000 VDD SDCLK 12
26 SDWP EN3/4
R248 SDWP
D[21] D[20] 2 +3.3V
IC208 17 18
DG NC
C209
1.0u
C210
0.1u
C211
1M +3.3V
RE2
DG D[19] 19 20 D[18]
1k
4.7K
20
DG 2.2u
40 IC202
R247
R210
VSSXSTANDBY
+3.3V D[17] D[16] 32 38 2 R215
21 22 TP1020 X202 TP1021 VSSTESTMODE
RI1+
7 37 VSS MINTESTY
39
SHW_CLK R209 3 TP682 220
23 24 20.000MHz
180
DG DG RO1
R219
DG DG 33
D[15] D[14] TP615 1 220
25 26
15p
15p
RI1-
C217
C218
+3.3V+3.3V+3.3V +3.3V+3.3V
TP683 R216
D[13] 27 28 D[12] +3.3V
DG
R211
RE2
4.7K
1 20
47K
47K
47K
47K
47K
CN211
0.1u
DIR VCC
C215
R239
R240
R241
R244
R242
D[11] 29 30 D[10]
2.2K
TP2018 TP697 DG
R221
19 18 A[8] DG SDDAT0 R223
/2G B1 D[9] 31 32 D[8] 7 DAT0 6
TP2008 DG TP2019 5 4 TP698 RI2+
LA[8] TP2064 TP2048 L218 2 17 A[7] SDDAT1 TP684 220
A1 B2 D[7] D[6] 6 3 8 DAT1 SHW_FH 5
33 34
180
7 2 RO2
R225
TP2020 TP699
22
5 4 TP2047 L217 TP2007 SDDAT2 +3.3V
RA203
LA[7] TP2063 3 A2 B3 16 A[6] 8 1 9 DAT2 220
6 3 D[5] 35 36 D[4] 7
7 2 TP2021 TP700 4 RI2-
TP2046 L216 TP2006
22
4 15 SDDAT3 R224
22k
LA[6] TP2062 A[5]
RA205
8 1 A3 B4 1 DAT3 EN1/2 TP685+3.3V
R237
D[3] 37 38 D[2] TP616
2.2K
R222
TP2045 L215 TP2005 SDCMD TP2022 TP1016 C

LA[5] TP2061 5 A4 B5 14 A[4] 2 CMD
D[1] 39 40 D[0] B J207
4.7K
TP2044 L214 TP2004 TP2023 5 4 TP1017 Q201

R212
DG
LA[4] TP2060 6 13 A[3] SDCLK 6 3 5 CLK R217 TP641 L209 TP649
A5 B6 41 42 10
TP2024 7 2 TP1018 E RI3+
22
5 4 TP2043 L213 TP2003 DG DG SDWP 22 1 2 FIL206
RA202
LA[3] TP2059 7 A6 B7 12 A[2] 8 1 11 WR_PROTECT DG 11 TP686
6 3 LD[15] 43 44 LD[14] LUHW[1]
180
RO3
R220
7 2 TP2042 L212 TP2002 TP2025 TP2017
22
LA[2] TP2058 8 11 A[1] SDCD TP681 TP687 22 TP642 L210 TP650 4 3
RA204
8 1 A7 B8 LD[13] 45 46 LD[12] 12 SDCD 9
+3.3V +3.3V +3.3V RI3-
LA[1] TP2057 TP2041 L211 TP2001 9 10 R218 J208
A8 GND LD[11] 47 48 LD[10] 10 Common
NC
R213
100K
100K
4.7K
C213
R251
R243
LD[9] 49 50 LD[8] 4 VDD
C212
1u
IC207 DG
4.7K
4.7K
R245
R246
DG LD[7] 51 52 LD[6] 3 VSS 14
RI4+ TP619
+3.3V DG DG DG
LD[5] LD[4] CN207 6 VSS 13
53 54 R203 TP601
TXD1 +3.3V RO4
LD[3] LD[2] 1 TX SG1 SG
55 56 33 TP602 15 TP620
12 RI4-
RXD1 R204 2 RX
LD[1] LD[0] SG2 SG EN3/4
57 58 33
3 VDD SG3 SG NC
59 60
DG
84
DG 4 GND
A[25] 61 62 A[24] DG
DG 5 N.C IC204
A[23] 63 64 A[22] TP603
nCTS1 R205 LA[1] 32 A0 AD0 44 LD[0]
6 CTS SD CARD CONNECTOR LA[2] 31 A1 43 LD[1]
A[21] 65 66 A[20] 33 TP604 AD1
nRTS1 R206 LA[3] 30 A2 AD2 42 LD[2]
7 RTS LA[4] 29 A3 41 LD[3]
A[19] 67 68 A[18] 33 AD3
+3.3V LA[5] 28 A4 AD4 38 LD[4]
IC209 LA[6] 27 A5 37 LD[5]
A[17] 69 70 A[16] 6 5 AD5
LA[7] 26 A6 AD6 36 LD[6]
J224 35 LD[7] 100K
A[15] 71 72 A[14] AD7 RA201
L228
IC209 TP621 1 10
A[13] 73 74 A[12] 12 13 FIL209 24 ADSEL D8 22
IC209 TP1024 23 ALE TP622 2 9
1 3 D9 21
D10 20 TP623 3 8
A[11] 75 76 A[10] 14 4
IC209 2 D11 19 TP624 7
TP625 5 6
0.1u
C219
1.0u
C220
A[9] A[8] 10 11 D12 16 DG
77 78 DG TP626
7 D13 15
A[7] A[6] D14 14 TP627
79 80 IC209 8 TP628
D15 13
+3.3V +3.3V 8 9
A[5] 81 82 A[4]
1 2
A[3] A[2] DG USBCLK
83 84 8 nCS_USB
3 4 -CS
A[1] A[0] DG -RD 9 nRD
85 86 6 XIN 10 DQMLL(nWE0)
5 6 -WR
87 88 R207 TP612 7 XOUT 34 nDREQ0
DG DG LDHW[0] DG 7 8 DG LUHW[0] TP611 -DREQ0
DQMLL(nWE0) DQMLU(nWE1) 1M R208 DACK0 33 nDACK0
89 90 TP689 4 TEST1 25 nDREQ1
RXD_RMT 9 10 TP691 TXD_RMT 680 -DREQ1
DQMUL(nWE2) DQMUU(nWE3) 12.000MHz 17 DACK1 18 nDACK1
91 92 TP690 TEST2 12 nIRQ_USB
RTS_RMT 11 12
TP692 CTS_RMT TP613 -INTR
nRD 93 94 RD/nWR +3.3V X201 DG
13 14 DSR_RMT -RST 11 nRESET
22P
22P
C201
C203
95 96 nCS0
VBUS
DG
15 16
nCS2 97 98 DG DG
L229
CH_SEL[2] DG 17 18 DG GAIN0 J226

nCS4 99 100 nCS5 TP693
GAIN1 19 20 nRESET NC USB CONNECTOR
nCS6 101 102 nRAS3L +5VRMT FIL201 TP614
Mu/nA 21 22 nPRS_RMT 3 1 3 VCC
nRAS3U 103 104 nCASL 40 VCC
LHWCLK[0] 2
23 24 R236
2.2u
C202
1.0u
C204
0.1u
C205
nCASU 105 106 CKE +3.3V

25 26 5.6K
nRESET nPRS_MEX 5 GND
107 108
J209
DG 27 28 39 GND
10K
R238
109 110 FSEL0 REMOTE CARD

29 30 DG J211 CN209
J210
MEX_MODE[0] 111 112 MEX_MODE[1] R226 TP633 0 USB_D- DG TP660
CN206 CONNECTOR -D 2 TP629 1 VBUS
DG 1 22
MEX_MODE[2] 113 114 MEX_MODE[3] DG +D 1 2 FIL202 TP661
TP695 TP2073 TP630 R227 2 USB_D-
NC
115 116 CKIO TP634 4 3 USB_D+ TP662
22 3 USB_D+
+3.3V TP696 J212
117 118 nCS3 J213 TP688 R214 4 GND
0
119 120
J214 1.5K DG
nCS2
DG CN205 DG +3.3V
C_CS[0]
DIN_RMT
DOUT_RMT
DCLK_RMT
+3.3V
+3.3V +3.3V
C_CS[0],DCLK_RMT,DIN_RMT,DOUT_RMT
16 16 16 14
IC201 IC202 IC203 IC206
0.1u
C206
0.1u
C207
0.1u
C208
0.1u
C214
NC NC
8 8 8 7
DG DG
DG DG

A[0-25]
D[0-31]
LD[0-15]
LA[1-16]
A[19] J301 10K +3.3V 10K +3.3V 10K +3.3V_CPU
A[22] J307
0 TP703 RA308 RA301 RA305
A[20] J302 A[23] J308 TP712
NC LD[15] 1 10 D[31] 1 10 A[25] 1 10
J303 LD[14] 2 9 D[30] 2 9 A[24] 2 9
0 IC309 J309 LD[13] 3 8 D[29] 3 8 A[23] 3 8
IC310 LD[12] 4 7 D[28] 4 7 A[22] 4 7
A[21] J304 TP704 1 15TP706 J329 A[24] J310 TP713
NC A Y0 1 15 nCS_FLASH0 5 6 5 6 5 6
NC A Y0
J305 2 14TP707 3.3V
B Y1 J311 2 14 nCS_FLASH1 LD[11] D[27] A[21]
0 B Y1
A[22] J306 TP705 3 13TP708 LD[10] D[26] A[20]
C Y2 A[25] J312 TP714 3 13 TP715 LD[9] D[25] A[19]
NC C Y2
12TP709 LD[8] D[24] A[18]
Y3 12 TP716
Y3 10K 10K 10K
1000P
11TP710
C307
Y4 +3.3V RA309 RA302 RA306
J315 11 TP717
Y4 LD[7] 1 10 1 1
nRESET DG 6 10TP711 D[23] 10 A[17] 10
G1 Y5 J316 6 10 TP718 LD[6] 2 9 D[22] 2 9 A[16] 2 9
nCS_SRAM0 TP773 G1 Y5 LD[5] 3 8 3 3
A[25] 4 9TP2075 J330 D[21] 8 A[15] 8
G2A Y6 4 9 TP719 LD[4] 4 7 D[20] 4 7 A[14] 4 7
0 nCS_SRAM1 G2A Y6 5 6
nCS4 5 7TP2076 J331 DG 5 6 5 6
G2B Y7 nCS0 5 7 TP720
J3280 TP774 G2B Y7
LD[3] D[19] A[13]
NC LD[2] D[18] A[12]
DQMLU(nWE1) IC311 LD[1]
1 TP775 nUB nCS_FLASH0 TP777 D[17] A[11]
2 3 LD[0] D[16] A[10]
TP778
nCS_FLASH1 10K 10K
DQMLL(nWE0) IC311 RA303 RA307
4 TP776 nLB
nRD 5 6 D[15] 1 10 A[9] 1 10
A[22] D[14] 2 9 A[8] 2 9
13 N.C./(A21) IC306 D[13] 3 8 A[7] 3 8
IC311 A[21] IC305 D[12] 4 7 A[6] 4 7
10 10 A20 DQ15/A-1 45 LD[15] 5 5
8 TP782 nWE A[14] 6 6
9 A[14] D[31]
22 BA0 DQ31 56 D[31]
A[20] 9 A19 DQ14 43 LD[14]
22 BA0 DQ31 56
A[13] A[13] 23 BA1 DQ30 54 D[30] D[11] A[5]
A[19] LD[13]
23 BA1 DQ30 54 D[30] D[10] A[4]
16 A18 DQ13 41
A[12] 24 A10/AP DQ29 53 D[29] D[9] A[3]
A[18] A[12] 24 A10/AP DQ29 53 D[29]
17 A17 DQ12 39 LD[12] D[8] A[2]
A[18] 18 A17 I/O15 38 LD[15] A[11]
A[11] D[28]
66 A9 DQ28 51 D[28] 10K
A[17] 48 A16 DQ11 36 LD[11]
66 A9 DQ28 51
A[17] 19 A16 I/O14 37 LD[14] A[10] RA304
A[10] 65 A8 DQ27 50 D[27] 10
LA[16] LD[10]
65 A8 DQ27 50 D[27] D[7] 1 A[1] R304 10K
LA[16] LD[13] 1 A15 DQ10 34 D[6] 2 9 A[0] R305
20 A15 I/O13 36 A[9] 64 A7 D[26] 10K
A[9] 64 A7 DQ26 48 D[26] DQ26 48 D[5] 3 8
LA[15] 2 A14 DQ9 32 LD[9]
LA[15] 21 A14 I/O12 35 LD[12] A[8] D[4] 4 7
A[8] 63 A6 D[25]
63 A6 DQ25 47 D[25] 5 6
LA[14] 3 A13 DQ8 30 LD[8] DQ25 47
LA[14] 22 A13 I/O11 32 LD[11] A[7]
A[7] 62 A5 DQ24 45 D[24]
LA[13] LD[7]
62 A5 DQ24 45 D[24] D[3]
LA[13] LD[10] 4 A12 DQ7 44
23 A12 I/O10 31 A[6] 61 A4 D[23] D[2]
A[6] 61 A4 DQ23 42 D[23] DQ23 42
LA[12] 5 A11 DQ6 42 LD[6] D[1]
LA[12] 24 A11 I/O9 30 LD[9] A[5] D[0]
A[5] 60 A3 D[22]
60 A3 DQ22 40 D[22]
LA[11] 6 A10 DQ5 40 LD[5] DQ22 40
LA[11] 25 A10 I/O8 29 LD[8] A[4]
A[4] 27 A2 D[21]
27 A2 DQ21 39 D[21]
LA[10] 7 A9 DQ4 38 LD[4] DQ21 39
LA[10] 26 A9 I/O7 16 LD[7] A[3]
A[3] 26 A1 DQ20 37 D[20]
LA[9] LD[3]
26 A1 DQ20 37 D[20]
LA[9] LD[6] 8 A8 DQ3 35
27 A8 I/O6 15 A[2] 25 A0 D[19]
A[2] 25 A0 DQ19 36 D[19] DQ19 36
LA[8] 18 A7 DQ2 33 LD[2]
LA[8] 42 A7 I/O5 14 LD[5]
D[18] DQ18 34 D[18]
LA[7] 19 A6 DQ1 31 LD[1] DQ18 34
LA[7] 43 A6 I/O4 13 LD[4] TP763
A[15] TP723 14 NC(A11) D[17] A[15] 14 NC(A11) DQ17 33 D[17]
LA[6] 20 A5 DQ0 29 LD[0] DQ17 33
LA[6] 44 A5 I/O3 10 LD[3] TP764
TP724 21 NC D[16]
21 NC DQ16 31 D[16]
LA[5] 21 A4 DQ16 31
LA[5] 1 A4 I/O2 9 LD[2] +3.3V +3.3V TP765
TP725 30 NC D[15]
30 NC DQ15 85 D[15]
LA[4] 22 A3 DQ15 85
LA[4] 2 A3 I/O1 8 LD[1] TP766
TP726 57 NC D[14]
57 NC DQ14 83 D[14]
LA[3] 23 A2 DQ14 83
10K
LA[3] 3 A2 I/O0 7 LD[0] TP767
10K
69 NC DQ13 82 D[13]
LA[2] TP779 TP727 69 NC DQ13 82 D[13]
LA[2] 24 A1 RY/#BY 15
4 A1 TP768
TP728 70 NC D[12]
70 NC DQ12 80 D[12]
LA[1] 25 A0 DQ12 80
R303
+3.3VB
R302
LA[1] 5 A0 TP769
+3.3V D[11]
73 NC DQ11 79 D[11]
#WP/ACC TP780 TP729 73 NC DQ11 79
A[19] J313 TP771 14
28 CS2/(A18) DQ10 77 D[10]
85
+3.3VB NC DQ10 77 D[10]
nWE
nCS_FLASH0 26 #CE J321
0
J317 R306 #WE 17
L301
nCS3 D[9] nCS3 20 #CS DQ9 76 D[9]
nRD NC 20 #CS DQ9 76
L303
NC 10K nUB 28 #OE
11 VDD #UB 40 FIL303 nRAS3U 19 #RAS D[8] +3.3VB
TP721 nRAS3L DQ8 74 D[8] DQ8 74 +3.3V
FIL301 TP701 DQMLL(nWE0) 11 #WE VCC 37 1 3
19 #RAS
3 1 33 VDD #LB 39 nLB +3.3V
nCASU 18 #CAS DQ7 13 D[7]
nRESET 2 nCASL 18 #CAS DQ7 13 D[7]
2 12 #RESET VSS 27
C308
0.1u
#CS1 6 nCS_SRAM0 RD/nWR D[6]
1.0u
C310
2.2u
C312
17 #WE DQ6 11
2.2u
C301
1.0u
C303
0.1u
C305
+3.3V RD/nWR 17 #WE DQ6 11 D[6]
nRD 47 #BYTE VSS 46
12 GND #OE 41 DQMUU(nWE3) 59 DQM3(bit31-24) D[5]
DQMUU(nWE3) 59 DQM3(bit31-24) DQ5 10 D[5] DQ5 10
34 GND IC303 DQMUL(nWE2) 28 DQM2(bit23-16) 8 D[4]
DQMUL(nWE2) 28 DQM2(bit23-16) DQ4 8 D[4] DQ4 14
IC311 IC309 16 IC310 16
DQMLU(nWE1) 7 D[3]
0.1u
C320
71 DQM1(bit15-8) DQ3
0.1u
C321
0.1u
C322
IC301 A[22] DQMLU(nWE1) 71 DQM1(bit15-8) DQ3 7 D[3]

DG 13 N.C./(A21) DG 7 8 8
5 DQMLL(nWE0) 16 DQM0(bit7-0) DQ2 5 D[2]
A[21] LD[15] DQMLL(nWE0) 16 DQM0(bit7-0) DQ2 D[2]
10 A20 DQ15/A-1 45
4 68 CLK DQ1 4 D[1]
A[20] LD[14]
68 CLK DQ1 D[1]
9 A19 DQ14 43
2 CKE 67 CKE DQ0 2 D[0]
A[19] LD[13] CKE 67 CKE DQ0 D[0]
A[18] LD[15] 16 A18 DQ13 41
18 A17 I/O15 38 3
A[18] VCCQ 3 VCCQ
17 A17 DQ12 39 LD[12] DG
A[17] 19 A16 I/O14 37 LD[14] 1 DG
1 VCC DG
A[17] 48 A16 DQ11 36 LD[11] VCC
LA[16] 20 A15 I/O13 36 LD[13]
VCC 15 VCC 15
LA[16] 1 A15 DQ10 34 LD[10] +3.3V
LA[15] 21 A14 I/O12 35 LD[12]
VCC 29 VCC 29
LA[15] 2 A14 DQ9 32 LD[9]
LA[14] 22 A13 I/O11 32 LD[11] +3.3V
VCC 43 VCC 43
LA[14] 3 A13 DQ8 30 LD[8]
L305
LA[13] 23 A12 I/O10 31 LD[10] J325

VCCQ 35 VCCQ 35
LA[13] 4 A12 DQ7 44 LD[7]
LA[12] 24 A11 I/O9 30 LD[9] NC
VCCQ 41
0
VCCQ 41 J327
L306
LA[12] 5 A11 DQ6 42 LD[6] TP762 FIL305

LA[11] 25 A10 I/O8 29 LD[8] 1 3
VCCQ 49 VCCQ 49 NC
LA[11] 6 A10 DQ5 40 LD[5]
LA[10] 26 A9 I/O7 16 LD[7] 2
VCCQ 55 VCCQ 55
LA[10] 7 A9 DQ4 38 LD[4] TP770 FIL306
LA[9] 27 A8 I/O6 15 LD[6] 1 3
VCCQ 75
1.0u
2.2u
0.1u
LA[9] 8 A8 DQ3 35 LD[3] VCCQ 75

LA[8] 42 A7 I/O5 14 LD[5] 2
VCCQ 81 VCCQ 81
DG
LA[8] 18 A7 DQ2 33 LD[2]

LA[7] 43 A6 I/O4 13 LD[4] 9
C315
C316
VCCQ
C314
1.0u
2.2u
9
0.1u
LA[7] 19 A6 DQ1 31 LD[1] VCCQ

LA[6] 44 A5 I/O3 10 LD[3]
VSS 44 VSS 44
LA[6] 20 A5 DQ0 29 LD[0]
LA[5] 1 A4 I/O2 9 LD[2]
C318
C319
VSS 58
C317
LA[5] 21 A4 VSS 58
LA[4] 2 A3 I/O1 8 LD[1]
VSS 72 VSS 72
LA[4] 22 A3
LA[3] 3 A2 I/O0 7 LD[0]
VSS 86 VSS 86
LA[3] 23 A2
LA[2] 4 A1 6
VSSQ 6 DG VSSQ
LA[2] 24 A1 RY/#BY 15
LA[1] 5 A0
+3.3VB VSSQ 12 VSSQ 12
A[19] J314 TP772 28 LA[1] 25 A0 +3.3V
CS2/(A18) VSSQ 32
+3.3VB NC #WP/ACC 14 VSSQ 32
0
J319 R307 #WE 17 nWE DG
VSSQ 38 VSSQ 38
L302
NC nCS_FLASH1 26 #CE
10K 11 VDD #UB 40 nUB J323
NC
VSSQ 46
L304
FIL302 TP702 nRD 28 #OE NC VSSQ 46

3 1 33 VDD #LB 39 nLB
TP722
FIL304 VSSQ 52
DQMLL(nWE0) 11 #WE VCC 37 1 3 VSSQ 52
2 #CS1 6 nCS_SRAM1
VSSQ 78
2.2u
C302
1.0u
C304
0.1u
C306
nRESET NC VSSQ 78
12 #RESET VSS 27 2
C309
C313
12 GND #OE 41 nRD

C311
+3.3V VSSQ 84
NC
NC
NC
47 #BYTE VSS 46 VSSQ 84

34 GND
DG
IC304 NC TP781
IC302 CKIO DG
CKIO

KX-TDA100BX
+3.3V +3.3V
+3.3V
C422
2.2K
2.2K
R414
R416
TP816 8 1 TP826 0.1u
LDHW[0] DR VagRef
LUHW[0] TP817 2 TP891 56K
13 DT RO-
KX-TDA100BX
DG
10 R423
/PDI
TP832
LHWCLK[0] TP818 11 MCKL PI 3
120P
9 BCLKR J402
R425
C419
56K
TP836 560 TP865 1.0u TP873L405
12 BCLKT PO- 4
C469 JK402
5 TP833 R429 C442 TP899 L414
PO+ 1 2 2
1000p
NC
C470 FIL403
NC
TP819 L415
C459
7
C441
R469
CH_SEL[0] FSR
3300P
4 3 4
560 1000p TP866 1.0u L406
14 FST TI+ 19
TP827 R430 R433 C443 TP874 TP900 J403
+3.3V TI- 18
+15V IC408
DG
6 TP828 100K 0.1u TP841
VDD TG 17 5 VREF
R427
100K
TP838 C425 0.1u 7
Mu/A 16 6 R452 C437 J404
C412
82K R444 L411
0.1u
15 VSS C427 R450 2.2K 0.033uTP861 4.7K TP863 47K TP867 1.0u
DG
R442 C430 82K +15V TP893 TP894 R458 R462 C445 TP875 TP901
DG 10K JK404
C413
2 8 IC408 TP849 TP851
DA401 Q407 C L418
0.01u
20 VAG 1
TP853 3 1 TP855 C 1 2
TP847 R453 TP859 FIL401 2
3 B Q409 L419
R460
R446 0.015u
NC
NC
2.2K
C439
4 E B 4 3
C456
R470
VREF 4
1000P
IC405 10K TP857 22K E
TP820 2
R448
1M
C435
1.0u
R456
Mu/nA
22K
DG MA143TW
TP824 1.0u
22u/16V
TP868 L407
NC C432
0
R464 C446 TP876 TP902 J405

+3.3V DG
NC
J413
C423 +15V
LDHW[0] 8 DR VagRef 1 TP831 0.1u AGC CIRCUIT DG
22K
R438
LUHW[0] 2 56K
13 DT RO- TP880
DG VREF
10 /PDI TP892 R424
TP834
22K
C433
0.1u
R439
LHWCLK[0] 11 MCKL PI 3
9 BCLKR J406
120P
R426
56K
C421
DG TP871 1.0u TP897 L408 TP903
12 PO- 4 TP837 560
BCLKT JK401
TP835 R431 C467 C449 L416
PO+ 5
1 2 FIL404 2
C468
NC
NC
TP821 1000p L417

C460
7
R471
C444
CH_SEL[1] FSR
3300P
4 3 4
560 1000p TP872 1.0u TP898 L409 TP904
14 FST TI+ 19
+3.3V TP829 R432 R434 C450 J407
TI- 18
+15V IC409 DG
6 VDD 17 TP830 47K TP839 0.1u TP840 33K TP842 22K TP879
TG 5 VREF
100K
R428
7
Mu/A 16 C424 R436 R437 0.1u 6 C438 J408
R454
C414
R445
0.033u
0.1u
15 VSS C428 R451 2.2K 4.7K TP864 47K TP869 1.0u TP877 L412 TP905
Q406 DG
C R443 82K C431 82K +15V TP895 TP896 TP862 R459 R463 C447
DG DA402 JK403
10K
C415
B 2 8 IC409 Q408 C
20 L420
0.01u
VAG TP850 TP852 TP854 3 1 TP856 1 2
1 C 2
TP848 3 TP858 R455 TP860
Q410 FIL402
B L421
R461
NC
NC
E R447 0.015u
C458
2.2K
C440
R472
VREF 4 E B 4 3 4
1000P
IC406 10K 2 22K E
R449
DG
1M
C436
1.0u
R457
Mu/nA DG
22K
MA143TW
22u/16V
TP825
NC C434
+3.3V 0 TP870 1.0u TP878 L410 TP906
R441 J409
R465 C448
22K
NC
0.1u DG
J414
33K TP843 R440

8 OUT OSC1 1
0.1u
C429
R435 C426 TP846 22K 7 VDD OSC2 2 AGC CIRCUIT DG
MELODYSEL TP844
6 SEL VSS 3
86
MOHSEL TP845
5 MT TST 4
IC410
DG
+15V
3.3V_BB
L403 TP810 Q404
E
3.3V_BB
B
C420
1.0u
C416
2.2u
J411 TP888
+15VIN 0
R412
6.8K
+3.3V
+15VIN TP805 IP402 DG DG
IP401 TP801 L401 TP807 L404 DG
S
+3.3V
1.9A/33u NC +3.3VB
680
Q412
D407
G
Q411
R410
L413
0.1u
D +3.3VB
C402
0
TP804 TP808
1.8V +15V
0.1u
C403
G Q405
330u/25V
C406
C
C408
E
5.1V
470u/6.3V
S 1.8V
D405
D402
R401
10K
R409
56
10K
R403
DG DG DG DG DG
P.G P.G P.G P.G P.G TP883 R415

NC
NC
NC
TP814
C463
C462
C461
680
R411
TP823
680
R417
DG DG
2 VDD VOUT 3
NC
5 VIN ON/#OFF 1 P.G P.G TP815

4 EXT
TP809
10u
C417
VSS 2
DG
NC
5 #CE GND 1
C464 R473
4 EXT VOUT 3
IC402
DG IC403 DG
C404
1.9VB
0.1u DG
2 3
P.G VIN VOUT 1.9VB
D406A
Q403 4.3V
D406
C
1
1.0u
+9.4V +5V
4 CE GND
C418
GND GND
1K +15V
B
1K IC404 DG DG
14
R406 TP806 14 DG DG
IC121 TP811 2 8 IC411
IC120 +3.3V
C410
0.1u
C411
0.1u
+3.3V 1
7 R421
10V
1 7 3
D403
D408 R413
BATALM 4
10M
2.2K
R422
TP812
R418
DG
TP890
4.7K
P.G DG
6 DG
DG IC412
IC413 7 nBAT_ALM
D409
4 NC D409A TP813 R420

Vin 2 3 Vout 5
1 NC V+ 8 +5VRMT IC411
5 NC 10K
2 C+ OSC 7
C454 1 GND
TP889
J412
3 GND Vr 6 BAT401+
C451
1.0u
C452
1.0u
10u/50V
10K
4 C- Vout 5
10M
R468
R419
BAT401
DG
DG
C453
10u/50V
DG
DG DG DG
P.G -9.3V BATTERY KX-TDA100 MPR CARD 5/5
P.G
20.2. BACK/LED BOARD
+40V +15V +40V +15V +40V +15V +40V +15V

+15VPT NC +15VPT
+3.3V +3.3V CN101 +15VPT CN102 +15VPT +15VPT CN103 +15VPT +15VPT CN104 +15VPT
10K NC 10K NC A1 B1 A1 B1 A1 B1
A1 B1
R101 R103 R147 R149 A2 B2 A2 B2 A2 B2 A2 B2
CT_D[0] EC_nSTOP POWERGND POWERGND POWERGND POWERGND POWERGND POWERGND POWERGND POWERGND
A3 B3 A3 B3 A3 B3 A3 B3
10K NC 10K NC EC_CLK EC_nSTOP EC_CLK EC_nSTOP EC_CLK EC_nSTOP EC_CLK EC_nSTOP
A4 B4 A4 B4 A4 B4 A4 B4
R102 R104 CT_D[1] R148 R150 EC_nTRDY A5 B5 A5 B5 A5 B5
EC_nTRDY A5 B5 EC_nPERR EC_nTRDY EC_nPERR EC_nTRDY EC_nPERR EC_nTRDY EC_nPERR
10K NC 10K NC A6 B6 A6 B6 A6 B6 A6 B6
EC_nFRAME EC_PAR EC_nFRAME EC_PAR EC_nFRAME EC_PAR EC_nFRAME EC_PAR
A7 B7 A7 B7 A7 B7 A7 B7
R105 R111 CT_D[2] R151 R158 EC_nPERR EC_nCBE[0] EC_nCBE[1] EC_nCBE[0] EC_nCBE[1] EC_nCBE[0] EC_nCBE[1] EC_nCBE[0] EC_nCBE[1]
A8 B8 A8 B8 A8 B8 A8 B8
10K NC 10K NC EC_AD[6] EC_nRST EC_AD[0] EC_nRST EC_AD[1] EC_nRST EC_AD[2] EC_nRST
A9 B9 A9 B9 A9 B9 A9 B9
R106 R112 CT_D[3] R152 R159 EC_nFRAME A10 B10 A10 B10 A10 B10 A10 B10
EC_AD[0] EC_AD[1] EC_AD[0] EC_AD[1] EC_AD[0] EC_AD[1] EC_AD[0] EC_AD[1]
A11 B11 A11 B11 A11 B11 A11 B11
10K NC 10K NC +15VPT +15VPT EC_AD[2] EC_AD[3] EC_AD[2] EC_AD[3] EC_AD[2] EC_AD[3] EC_AD[2] EC_AD[3]
CN100 A12 B12 A12 B12 A12 B12 A12 B12
R107 R113 R153 R160 EC_AD[4] EC_AD[5] EC_AD[4] EC_AD[5] EC_AD[4] EC_AD[5] EC_AD[4] EC_AD[5]
CT_D[4] EC_PAR A1 A13 B13 A13 B13 A13 B13 A13 B13
B1
10K NC 10K NC A2 B2 A14 B14 A14 B14 A14 B14 A14 B14
A3 B3 A15 B15 A15 B15 A15 B15 A15 B15
R108 R114 CT_D[5] R154 R161 EC_nCBE[0] +15V EC_AD[8] EC_AD[9] EC_AD[8] EC_AD[9] EC_AD[8] EC_AD[9] EC_AD[8] EC_AD[9]
A4 B4 A16 B16 A16 B16 A16 B16 A16 B16
10K NC 10K NC +15V EC_AD[10] EC_AD[11] EC_AD[10] EC_AD[11] EC_AD[10] EC_AD[11] EC_AD[10] EC_AD[11]
A5 B5 A17 B17 A17 B17 A17 B17 A17 B17
+40V Reserve-B18 Reserve-B18 Reserve-B18 Reserve-B18
R109 R115 R155 R162 +40V A18 B18 A18 B18 A18 B18 A18 B18
CT_D[6] EC_nCBE[1] A6 B6 EC_AD[12] EC_AD[13] EC_AD[12] EC_AD[13] EC_AD[12] EC_AD[13] EC_AD[12] EC_AD[13]
10K NC 10K NC A7 B7 A19 B19 A19 B19 A19 B19 A19 B19
A8 B8 A20 B20 A20 B20 A20 B20 A20 B20
R110 R116 R156 R163 EC_nINT EC_nCDET EC_nINT EC_nCDET EC_nINT EC_nCDET EC_nINT EC_nCDET
CT_D[7] EC_nRST A9 A21 B21 A21 B21 A21 B21 A21 B21
B9 Reserve-B22 Reserve-B22 Reserve-B22 Reserve-B22
10K NC POWERGND A22 B22 A22 B22 A22 B22
A10 B10 CT_D[0] A22 B22 CT_D[1] CT_D[0] CT_D[1] CT_D[0] CT_D[1] CT_D[0] CT_D[1]
A11 B11 A23 B23 A23 B23 A23 B23 A23 B23
R157 R164 EC_AD[0] CT_D[2] CT_D[3] CT_D[2] CT_D[3] CT_D[2] CT_D[3] CT_D[2] CT_D[3]
A12 B12 A24 B24 A24 B24 A24 B24 A24 B24
NC NC 10K NC CT_D[4] CT_D[5] CT_D[4] CT_D[5] CT_D[4] CT_D[5] CT_D[4] CT_D[5]
A13 B13 A25 B25 A25 B25 A25 B25 A25 B25
CT_D[6] CT_D[7] CT_D[6] CT_D[7] CT_D[6] CT_D[7] CT_D[6] CT_D[7]
R117 R123 Reserve-A31 R165 R171 EC_AD[1] A14 B14 A26 B26 A26 B26 A26 B26 A26 B26
Reserve-B27 Reserve-B27 Reserve-B27 Reserve-B27
NC NC 10K NC A15 B15 A27 B27 A27 B27 A27 B27 A27 B27
CT_NETREF CT_C8 CT_NETREF CT_C8 CT_NETREF CT_C8 CT_NETREF CT_C8
A16 B16 A28 B28 A28 B28 A28 B28 A28 B28
R118 R124 R166 R172 CT_FRAME nLOS CT_FRAME nLOS CT_FRAME nLOS CT_FRAME nLOS
Reserve-B31 EC_AD[2] A17 A29 B29 A29 B29 A29 B29 A29 B29
B17
NC NC 10K NC +30V A30 B30 A30 B30 A30 B30
A18 B18 Reserve-A31 A30 B30 Reserve-B31 Reserve-A31 Reserve-B31 Reserve-A31 Reserve-B31 Reserve-A31 Reserve-B31
A19 B19 A31 B31 A31 B31 A31 B31 A31 B31
R119 R125 Reserve-A32 R167 R173 EC_AD[3] Reserve-A32 Reserve-B32 Reserve-A32 Reserve-B32 Reserve-A32 Reserve-B32 Reserve-A32 Reserve-B32
nBATT A32 B32 A32 B32 A32 B32
A20 B20 Reserve-A33 A32 B32 Reserve-B33 Reserve-A33 Reserve-B33 Reserve-A33 Reserve-B33 Reserve-A33 Reserve-B33
NC NC 10K NC POWTYPE[0]
A21 B21 A33 B33 A33 B33 A33 B33 A33 B33
TXD2 RXD2 TXD2 RXD2 TXD2 RXD2 TXD2 RXD2
R120 R126 R168 R174 DC_ALM A34 B34 A34 B34 A34 B34 A34 B34
Reserve-B32 EC_AD[4] A22 B22 Reserve-A35 Reserve-B35 Reserve-A35 Reserve-B35 Reserve-A35 Reserve-B35 Reserve-A35 Reserve-B35
NC NC 10K NC AC_ALM A35 B35 A35 B35 A35 B35 A35 B35
nBATT Reserve-B36 nBATT Reserve-B36 nBATT Reserve-B36 nBATT Reserve-B36
A36 B36 A36 B36 A36 B36 A36 B36
R121 R127 R169 R175 POWTYPE[1] nFAN_ALM Reserve-B37 nFAN_ALM Reserve-B37 nFAN_ALM Reserve-B37 nFAN_ALM Reserve-B37
Reserve-A33 EC_AD[5] A37 B37 A37 B37 A37 B37 A37 B37
+30V +30V +30V +30V +30V +30V +30V +30V
NC NC 10K NC nFAN_ALM A38 B38 A38 B38 A38 B38 A38 B38
RINGER RING_SYNC RINGER RING_SYNC RINGER RING_SYNC RINGER RING_SYNC
87
+30V A39 B39 A39 B39 A39 B39 A39 B39
R122 R128 Reserve-B33 R170 R176 EC_AD[6] nHALT RING_SIN +3.3V nHALT RING_SIN +3.3V nHALT RING_SIN +3.3V nHALT RING_SIN +3.3V
A40 B40 A40 B40 A40 B40 A40 B40
NC NC 10K NC POWERGND
A41 B41 A41 B41 A41 B41 A41 B41
DC_ALM AC_ALM DC_ALM AC_ALM DC_ALM AC_ALM DC_ALM AC_ALM
R129 R135 TXD2 R177 R183 EC_AD[7] A42 B42 A42 B42 A42 B42 A42 B42
POWTYPE[0] POWTYPE[1] POWTYPE[0] POWTYPE[1] POWTYPE[0] POWTYPE[1] POWTYPE[0] POWTYPE[1]
A43 B43 A43 B43 A43 B43 A43 B43
NC NC 10K NC DIAG_R DIAG_T DIAG_R DIAG_T DIAG_R DIAG_T DIAG_R DIAG_T
A44 B44 A44 B44 A44 B44 A44 B44
R130 R136 R178 R184 RINGER_AC RINGER_AC RINGER_AC RINGER_AC
RXD2 EC_AD[8] A45 B45 A45 B45 A45 B45 A45 B45
NC NC 10K NC
R131 R137 Reserve-A35 R179 R185 EC_AD[9]

NC NC 10K NC
R132 R138 Reserve-B35 R180 R186 EC_AD[10]

+3.3V
NC NC 10K NC
R133 R139 Reserve-B36 R181 R187 EC_AD[11] C101

NC NC 10K NC 2.2u
R134 R140 nFAN_ALM R182 R188 EC_AD[12] C106
NC NC 10K NC 0.1
R141 R144 Reserve-B37 R189 R194 EC_AD[13] C107
10K NC 0.1
R190 R195 EC_AD[14] C108
10K NC 0.1
R191 R196 EC_AD[15] C109
10K NC 0.1
R192 R197 EC_nINT C110
10K NC 0.1
R193 R198 EC_nCDET C111
0.1
+3.3V GND
10K NC C102
R199 R203 NC CT_NETREF

10K NC C103
R200 R204 NC CT_C8

10K NC C104
R201 R205 NC CT_FRAME

10K NC C105
R202 R206 NC EC_CLK
KX-TDA100 BACK/LED BOARD 1/3

KX-TDA100BX
KX-TDA100BX
+40V +15V +40V +15V +40V +15V

+15VPT CN105 +15VPT +15VPT CN106 +15VPT +15VPT CN107 +15VPT
A1 B1 A1 B1 A1 B1
A2 B2 A2 B2 A2 B2
POWERGND POWERGND POWERGND POWERGND POWERGND POWERGND
A3 B3 A3 B3 A3 B3
EC_CLK EC_nSTOP EC_CLK EC_nSTOP EC_CLK EC_nSTOP
A4 B4 A4 B4 A4 B4
A5 B5 A5 B5 A5 B5
EC_nTRDY EC_nPERR EC_nTRDY EC_nPERR EC_nTRDY EC_nPERR
A6 B6 A6 B6 A6 B6
EC_nFRAME EC_PAR EC_nFRAME EC_PAR EC_nFRAME EC_PAR
A7 B7 A7 B7 A7 B7
EC_nCBE[0] EC_nCBE[1] EC_nCBE[0] EC_nCBE[1] EC_nCBE[0] EC_nCBE[1]
A8 B8 A8 B8 A8 B8
EC_AD[3] EC_nRST EC_AD[4] EC_nRST EC_AD[5] EC_nRST
A9 B9 A9 B9 A9 B9
A10 B10 A10 B10 A10 B10
EC_AD[0] EC_AD[1] EC_AD[0] EC_AD[1] EC_AD[0] EC_AD[1]
A11 B11 A11 B11 A11 B11
A12 B12 A12 B12 A12 B12
A13 B13 A13 B13 A13 B13
A14 B14 A14 B14 A14 B14
A15 B15 A15 B15 A15 B15
A16 B16 A16 B16 A16 B16
A17 B17 A17 B17 A17 B17
Reserve-B18 Reserve-B18 nSHW_CLK
A18 B18 A18 B18 A18 B18
A19 B19 A19 B19 A19 B19
A20 B20 A20 B20 A20 B20
EC_nINT EC_nCDET EC_nINT EC_nCDET EC_nINT EC_nCDET
A21 B21 A21 B21 A21 B21
Reserve-B22 Reserve-B22 nSHW_FH
A22 B22 A22 B22 A22 B22
CT_D[0] CT_D[1] CT_D[0] CT_D[1] CT_D[0] CT_D[1]
A23 B23 A23 B23 A23 B23
A24 B24 A24 B24 A24 B24
A25 B25 A25 B25 A25 B25
88
A26 B26 A26 B26 A26 B26
Reserve-B27 Reserve-B27 MASTER/nS
A27 B27 A27 B27 A27 B27
CT_NETREF CT_C8 CT_NETREF CT_C8 CT_NETREF CT_C8
A28 B28 A28 B28 A28 B28
CT_FRAME nLOS CT_FRAME nLOS CT_FRAME nLOS
A29 B29 A29 B29 A29 B29
A30 B30 A30 B30 A30 B30
Reserve-A31 Reserve-B31 Reserve-A31 Reserve-B31 Reserve-A31 Reserve-B31
A31 B31 A31 B31 A31 B31
A32 B32 A32 B32 A32 B32
A33 B33 A33 B33 A33 B33
TXD2 RXD2 TXD2 RXD2 nLDHW[1] nLUHW[1]
A34 B34 A34 B34 A34 B34
A35 B35 A35 B35 A35 B35
nBATT Reserve-B36 nBATT Reserve-B36 nBATT Reserve-B36
A36 B36 A36 B36 A36 B36
nFAN_ALM Reserve-B37 nFAN_ALM Reserve-B37 nFAN_ALM Reserve-B37
A37 B37 A37 B37 A37 B37
+30V +30V +30V +30V +30V +30V
A38 B38 A38 B38 A38 B38
RINGER RING_SYNC RINGER RING_SYNC RINGER RING_SYNC
A39 B39 A39 B39 A39 B39
nHALT RING_SIN +3.3V nHALT RING_SIN +3.3V nHALT RING_SIN +3.3V
A40 B40 A40 B40 A40 B40
A41 B41 A41 B41 A41 B41
DC_ALM AC_ALM DC_ALM AC_ALM DC_ALM AC_ALM
A42 B42 A42 B42 A42 B42
POWTYPE[0] POWTYPE[1] POWTYPE[0] POWTYPE[1] POWTYPE[0] POWTYPE[1]
A43 B43 A43 B43 A43 B43
DIAG_R DIAG_T DIAG_R DIAG_T DIAG_R DIAG_T
A44 B44 A44 B44 A44 B44
RINGER_AC RINGER_AC RINGER_AC
A45 B45 A45 B45 A45 B45

+40V +15V
+15VPT CN112 +15VPT +3.3V +3.3V
NC NC
A1 B1 NC NC
A2 B2 R301 R304 Reserve-A31 R323 R326 CT_D[0]
POWERGND POWERGND
A3 B3 NC NC
EC_CLK EC_nSTOP NC NC
A4 B4
R302 R305 Reserve-B31
A5 B5 CN113 R324 R327 CT_D[1]
EC_nTRDY EC_nPERR L104 NC NC
A6 B6 ER1 NC NC
EC_nFRAME EC_PAR 1
A7 B7 DR1 L105 R303 R306 Reserve-A32
EC_nCBE[0] EC_nCBE[1] 2 R325 R328 CT_D[2]
A8 B8 L106
EC_AD[11] EC_nRST RS1 NC NC
A9 B9 3 NC NC
CS1 L107 R307 R313 Reserve-B32
A10 B10 4 R329 R334 CT_D[3]
EC_AD[0] EC_AD[1]
A11 B11 RXD1 L108 NC NC
EC_AD[2] EC_AD[3] 5 NC NC
A12 B12 L109
EC_AD[4] EC_AD[5] TXD1 R308 R314 Reserve-A33 R330 R335
A13 B13 6 CT_D[4]
GND L110 NC NC
A14 B14 7 NC NC
EC_AD[6] EC_AD[7]
A15 B15 FG L111 R309 R315 Reserve-B33
EC_AD[8] EC_AD[9] 8 R331 R336 CT_D[5]
A16 B16 L112
EC_AD[10] EC_AD[11] NC NC
A17 B17 9 NC NC
nSHW_CLK DCD1 R310 R316
A18 B18 Reserve-A35 R332 R337
EC_AD[12] EC_AD[13] CT_D[6]
A19 B19 NC NC
EC_AD[14] EC_AD[15] NC NC
A20 B20
EC_nINT EC_nCDET R311 R317 Reserve-B35
A21 B21 CN114 R333 R338 CT_D[7]
nSHW_FH LEDALM L101 NC NC
A22 B22 1
CT_D[0] CT_D[1]
A23 B23 L103 R312 R318 nFAN_ALM
CT_D[2] CT_D[3] 2
A24 B24 LEDRUN L102
CT_D[4] CT_D[5]
A25 B25 3 NC NC
CT_D[6] CT_D[7]
A26 B26
89
MASTER/nS R340 R342 Reserve-B36
A27 B27
CT_NETREF CT_C8
A28 B28
CT_FRAME nLOS +3.3V
A29 B29 LED202 CN201
A30 B30 Red 10K NC C208
TXD1 RXD1 1
A31 B31 2 1 C201 R343 R346 NC CT_NETREF
CS1 RS1
A32 B32 2 2.2u
DR1 ER1 10K NC C209
A33 B33 3
nLDHW[1] nLUHW[1] 2 1 C202 R344 R347
A34 B34 NC CT_C8
LEDRUN LEDALM Green
A35 B35 LED201 0.1 10K NC C210
nBATT DCD1
A36 B36
nFAN_ALM C203 R345 R348 NC CT_FRAME
A37 B37
+30V +30V 0.1
A38 B38
RINGER RING_SYNC
A39 B39 C204 C205
nHALT RING_SIN +3.3V Open:Mtype Short:Stype
A40 B40 0.1 0.1
A41 B41
DC_ALM AC_ALM C206
A42 B42
POWTYPE[0] POWTYPE[1]
A43 B43 0.1
DIAG_R DIAG_T
A44 B44 C207
RINGER_AC
A45 B45
0.1

KX-TDA100BX
20.3. WAVEFORM
KX-TDA100BX
Waveform 1 Waveform 2 Waveform 3
16.384MHz 32.768kHz 65.536MHz
90
Waveform 4 Waveform 5 Waveform 6
16.384MHz
Switching the frequency of 20Hz/25Hz is Switching the pulse spacing of 2976msec/3840msec
possible by the soft setting. /4992msec/5120msec is possible by the soft setting.
The abobe-mentioned waveform is the The abobe-mentioned waveform is the example of
example of 20Hz. 5120msec.
Waveform 7 Waveform 8
20MHz 12MHz
91
KX-TDA100BX
21 PRINTED CIRCUIT BOARD
KX-TDA100BX
21.1. MPR CARD
C408 1 8
C402 CN103
L401 IC413
C454
C453
Q411
D407
4 5
R504 J301 R192
R401
A1 A45
J303
J302
L168
L169
L170
L171
14 8 16 IP401
R557
R558
J329 16 B1 R194 5 L161 10 L165 L16715 20 25 30 35 40 B45
IC309 9 J330 RA136
RA135
16 IC310 9 IC127 IC201 9 J331 R193 RA134
L164 R196
R568
14 IC311 8 J304 RA137
L166 R563 8 14
J328
1 8 1 8 J305 1 8 120 L163 R195 L173 R559 J134 14 8 R519 J160
L175
1 7 1 7 J306 14 8 J161
J308
1
J307 L172 FIL111 J163
121 R503
L191
2
R191 L174 IC120 IC121 J162
J309
J311
C160
IC110
L176 C159 1 7
L177 14 8 1 7
CN206
J310
J312
7 1
R306
R178
R565
R307 J314 J313
J159
29
30
IC111
FIL107
L148 R553
L150 L149
R197 L151
L153 L152
L155 L154
L156
L158 L157
L160 L159
L162
44 23 44 23 R153
R151
R155
R166
R167
R156
R152
J132
BAT401(CR2354)
1 7
X103
L192 C465
R143
14 8
IC102
IC302 IC301 FIL301 FIL110 D408
SW104 R413 D409
R524
L301
IC131
X104
R418
C466 1 7
1 22 1 22 J317 R468
R419
R420
R567 R569
L146 R189 J412
L144 IC132 8 5
R564
IC404
L142 1
R560
L140 R417 R415 Q405 IC411
L138 181 R142 240 C418 1
1
2
R561 180
L136 14 8 4
RA309 L134
R145
R179
R181
R505
R146
R183
R184
R186
R185
R188
R187
R190
L184
L183
R182
R180
R521
R520
L186
L185
25 24 L132 L187
RA308
IC403
C417
IC125
L130
C167
RA304 RA303 RA302 RA301
7
L128 1 R206
C464 R473
L126 7
92
L124 R205
IC304 L305 R246
R245
L122 RA108 RA102 X102

R566
R124 L120 43 R440

CN207
L204 R229 J325 5

RA106
RA104
1 R204
C166
R120 L116 52 1
RA116
8
1
48 1 L205 FIL204 R122 L118 RA307
R230
C426
R107 L105 208
CN205
L206 R231 R109 L107 IC305 Q406 IC410
C216
25 24 R111 RA114
R416
RA306 1
R428
R427
L207 FIL205 4 C415 C413
R232
R436 R435
20
11 20
PSUP1317ZB
L208 R233 44 85 C428 5 8 C4275 11
L217 L218 8
IC303 L216
L215 IC101
R220
R209
L214
RA305
IC408
IC406
IC405
C215
R218 L210 L213 L212 RA112
IC409
R518
48 1 14 IC130 8 L211 R513 1 1 10
R514 10 1
R247
R203 R445 4 R444 4 1
119
120
RA204 RA205 C161 R515
C218
R516 R447 R446 R424 R423
1 7 1 14 R517 R130
R248
C217
R551 R507 R128 C434 C432 Q407
QA102 1 IC126 157
14 R508 J158 DA402
R511
R510
16 105 156 Q408

9 7 8 R570
J101
R525
J139
DA401
C114
C212 IC206 J102 R454
C214
X202
R550
44 34 R449 R452
C173
8
R506
R512
12 1 IC202 R448
L114
L121
L110
L113
13 9 1 8 12 7 33 X101 C438 R457 R456 C437
C201
8 1 Q410 R455 R453
R219
48 L203 R228 FIL203 J201
R462
R465
1
J105
R555 L109
R127
R103 R126
C132
R464
R422
IC205 J202 R458 Q409

R125
R114
R117
R118
R113
R223 IC204 R207 C450 C449 C445 C448
R221
J203
R211
SW102
C129
C203 X201
C442
R208
C446
C447 R463
J204 R214
C443 R459
RA202 24
J124
J123
37
R216
R210
R215
R209
R237
J211
J121
J122
R224 J205 L411 L410 L412

L408
25 C213 36 23 L406 L405L409
R222
16 J206 11
R244 10 9 R217 22 R236 MOH#2 MOH#1 PAGE#2 PAGE#1 J407
J207
J408
CN211 R212
J403
FIL202
R239
R243
R242 R227 R238
R241
R251R240 IC203 J208 FIL402
C208
J212
J404
J409
J402
J406
J405
RA201
R226
FIL206 R469 R471 R472

11 8 2 1 C459
R213
QA103 C456 C458
QA101 1 3 4 C460 J414
J113
FIL403 J413
R164
R148 JK403 JK404 JK401 JK402
R176
L407
SW101 SW103 CN209

J114 FIL401
FIL404
RESET R470
BATALM
SDIN
INIT NORM
LED103
LED101
SG SG
KX-TDA100 MPR CARD COMPONENT VIEW

C404
C452
C451
R409
R410
C406
L404
L413
Q412
C403
J411
RA129 RA128 RA127 RA126 RA125 RA124 RA123 RA133 Q403 Q404 3.3V BB
R403 C416
IC412
R406 IC402 L403
D402
C420
IP402
D403
+3.3V
R412
+15VIN
D405 R411
GND
C321 C206 C322
C162
C320
nTRST
TMS
TD0
TDI
TD0A
TCK
R168
R170
R554
R171
R158
R174
R162
R175
C149
C163 J136 C148 C175
Q101 C411 C410 C150 R172
R163
R173
D406 J315 J316
R165
R159
R522
R161
R150
R157
C151
L193
FIL109
R144
FIL108
J131
J155
J135
C139
J127
L178
R562
C169 J130
C168
D406A
L147 R199
L145 J129
C143
C140
R501
R156
R157
J128
FIL302
L143 C302
C141 PLLCLK
J125 J126
BAT401+ C147
R528
R527
L141 RA122 +3.3VB
C142
L139 C301 C304
L137 J133 L189 C306 L302
J319
R531R532
L135 RA121
R530 R529
R526
C305
C303
D409A L133 RA118 RA117
L190
L131 RA120 FIL106
RA119
L129 R140 C307
R421 L127 J157
L125 J156
L123 C146
L108 C145 C144
L115
L117
C170 L119 1 20
1.8V R106 J323
L106
IC123
1.9VB R110 R302
R304 10 11 R303
FIL305
L304
L103 XTAL RA105 RA109 1 20

C313
C309
C311
C135
C136 C316 86 44 L225
R136
R135
#WP/ACC
IC124
R131 R305
FIL304
FIL306 L223
C126
C116
C121
J107 RA103 RA107 10 11 L221
R439 C319
C315
R438 J106 C107 C106 L219
R441
L306 J327
R138
C108
L194
C433 C429 J110 IC306 20 11
J152 L226 RA207
L303
C318
C463
C462
C461
RA115
J109 C105 IC208
C104
R433 R434 C101 C130 C314 L224 J321
C317
FIL101 1
93
OFF ON C134 1 43 10 L222
R502
R437
C425
RA113
C102
C133 J213 J214
RA206
C412
C414
FIL303
C424
SW106 20 11 L220
R523
C310
C308
R414
C131 IC207
FIL105
C120
J217 J224
R450
J120
RA111
FIL104 14
R443
R442
R451
R119 1 10 C174
C312 C220
C219
R549 SCLK J153 8

C422 C423 R121 C171 R552 L228
R104
C455
DIP00 R123 C172
C119
C103 C110
FIL209
L195
C112
C430
C431 DIP02 DIP01
R134 C111 R108 J210 J209
L101
L102
1 IC209 7
C117
C122
C127
C436 DIP03 C125
C435 DIP04 R556 R112
R425
C419
R129
DIP05
C128
OFF ON R509 FIL208
C137
C138
DIP06 J227
R102
R198
DIP07
C124
C207 SDCLK
R137
R249
C123
C118
R426
C421
R431
R460
C439
R461
C440
J216
1
C109
FIL102 J215 R250
C470
RA101 FIL103 8 C204 USBCLK RA203
R429
FIL201 C209 FIL207
R432 C468 C469 IC103 SW107 C205 Q201
C444 C441 L154 OFF ON C202 C211 L227
R430
J108
R132
R133
C467
4 5 J226 IC107 J222
C210
L196 D102
R105
L229
J116
L414
L415
L416
L417
L418
L419
L420
L421
BATALM
J115
KX-TDA100 MPR CARD BOTTOM VIEW
KX-TDA100BX
94
A22
A1
C109 C108 CN100

R133 C110
R140
B1
C104
R134 R139
B22
R141
R144 C106
R206
C111 C107
R195 R185 R176 R171 C101 R158 C105
R190 R179 R170 R165 R151 R202
R138 R123 R205 R111 R197 R191 R178 R177 R157 R156 R148 R147
R132 R117 R201 R105 R192 R196 R184 R183 R164 R163 R150 R149
R131 R118 R200 R106 R193
21.2. BACK/LED BOARD
R137 R124 R204 R112 R198 R194 R186 R175 R172 R162 R159
R136 R125 C103 R113 R103 R189 R180 R169 R166 R155 R152
R130 R119 R199 R107 R101 R182 R181 R168 R167 R154 R153
R129 R120 R203 R108 R102 R188 R187 R174 R173 R161 R160
R135 R126 R102 R114 R104
R128 R127 R110 R109
R122 R121 R116 R115
A45
A1
CN102
B1
B45
A45
A1
CN103
B1
B45
A45
A1
CN104
B1
B45
A45
A1
CN105
B1
B45
A45
A1
CN106
B1
B45
A45
A1
CN107
B1
R313 R306
B45
R311 R303
R307 C209 R347
C204 C203
R317 R308 R302 C210 R344
R314 R305 R348 R343
R318 R342 R316
R310 R315 R304 C201 R345 R346
R312 R340 C207 C208
A45
C202 R309 R301
A1
CN112
B1
L105 L112 L108 L101 R338 R335 R334 R326

R333
B45
L104 L106 L110 L111 9 L107 L103 R330 R329 R323
R332 R331 R325 R324 C205 PSUP1367Z-A
1 L109 L102 C206 R337 R336
1 R328 R327
B
CN113 3 1 3
B
CN114
RUN
CN201
ALM
LED201
LED202
KX-TDA100 BACK/LED BOARD COMPONENT VIEW

PSUP1367Z-B
KX-TDA100BX
B A B A B A B A B A B A B A
B A +15VPT +15VPT 1 1 1 1 1 1
LED202
1 +15V +40V
Power GND Power GND +15VPT
+15VPT
EC_nSTOP EC_CLK
GND GND 5 5 5 5 5 5 5
+15V
5 EC_nPERR EC_nTRDY +15V
EC_PAR EC_nFRAME
EC_nCBE[1] EC_nCBE[0] +40V
+40V
LED201
EC_nRST EC_AD[5] EC_AD[4] EC_AD[3] EC_AD[2] EC_AD[1] EC_AD[0] EC_AD[6]
EC_AD[11] GND GND 10 10 10 10 10 10
10 EC_AD[1] EC_AD[0] Power GND
EC_AD[3] EC_AD[2]
EC_AD[5] EC_AD[4]
Power GND
GND GND
EC_AD[7] EC_AD[6] 15 15 15 15 15 15
15 EC_AD[9] EC_AD[8]
EC_AD[10]
EC_AD[11]
nSHW_CLK GND
EC_AD[13] EC_AD[12]
EC_AD[15] EC_AD[14] 20 20 20 20 20 20
20 EC_nCDET EC_nINT
nSHW_FH GND 22
CT_D[1] CT_D[0]
CT_D[3] CT_D[2] +30V +30V
CT_D[5] CT_D[4] 25 25 25 25 25 Power GND Power GND
25 CT_D[7] CT_D[6] nFAN_ALM nBATT
MASTER/nS GND POWTYPE[1] POWTYPE[0]
95
CT_C8 CT_NETREF AC_ALM DC_ALM
nLOS CT_FRAME
GND GND 30 30 30 30 30
GND GND Reserved Reserved
RXD1 TXD1 Reserved Reserved
RS1 CS1 Reserved Reserved
ER1 DR1 nLUHW[1] nLDHW[1]
RXD2 TXD2 Reserved Reserved 35 35 35 35 35
LEDALM LEDRUNReserved nBATT
DCD1 M/nS nFAN_ALN
M/nS +30V +30V
RING_SYNC RINGER
RING_SIN nHALT 40 40 40 40 40
40 +3.3V GND
AC_ALM DC_ALM
POWTYPE[1] POWTYPE[0]
DIAG_T DIAG_R
RINGER_AC GND 45 45 45 45 45
45
KX-TDA100 BACK/LED BOARD BOTTOM VIEW

KX-TDA100BX
KX-TDA100BX
A,
96 KXTDA100BX

Panasonic Kx-Tda100bx Hybrid Ip-Pbx

Uploaded by

Copyright:

Available Formats

Panasonic Kx-Tda100bx Hybrid Ip-Pbx

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Panasonic Kx-Tda100bx Hybrid Ip-Pbx

Uploaded by

Copyright:

Available Formats

ORDER NO.

IMPORTANT INFORMATION ABOUT LEAD FREE, (PbF), SOLDERING

© 2003 Panasonic Communications Co., Ltd. All

1 ABOUT LEAD FREE SOLDER (PbF: Pb free)

1.1. SUGGESTED PbF SOLDER

1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS USED

Marked PbF (PbF is marked around here)

C202 R309 R301 C207 C208

L105 L112 L108 L101 R338 R335 B1

R333 R334 R326

2 FOR SERVICE TECHNICIANS

3.2. SAFETY PRECAUTIONS

3.3. INSULATION RESISTANCE TEST

3.4. BATTERY CAUTION

4.3. SYSTEM CAPACITY

*1 One T1, E1, PRI30 and PRI23 card counts as 2 cards.

4.3.2. Maximum Terminal Equipment

4.3.3. Power Supply Unit Selection

Load Figure Calculation

*2 Available for the KX-TDA100 and KX-TDA200.

5.2. SYSTEM COMPONENTS

Abbreviations in this manual

5.3. SYSTEM CONNECTION DIAGRAM

6 NAME AND LOCATIONS

Slot Type MPR Card CO Line Cards OPB3 Card

5. Loosen the two Screws.

7.2. DISASSEMBLY INSTRUCTION (BACK BOARD)

3. Remove the Hook. Remove the Top Cover.

4. Remove nine Screws (B).

6. Remove the RS-232C Connector and LED Connector from Back

9. Remove the LED Connector from Back Board 2.

8.2. SYSTEM CONTROL

8.2.2. Voice (TDM Highway) Bus Block Diagram

8.2.3. Voice Bus Logical Assignment

Back board waveform of TDM bus for voice

8.3. BACK BOARD SIGNAL CONNECTION DIAGRAM

8.3.2. EC Bus System Connection Diagram

8.3.3. System Control and Analog Signal Connection Diagram

8.3.4. Power Supply System Connection Diagram

9 MPR CARD CIRCUIT OPERATION

9.1.2. Description of Each Part

IC301, IC302 IC303 IC305, IC306

ADD BUS A1-A23 ADD

9.1.4. Circuit Description

9.1.4.2. Detail of Block Description

Signal Name Functions

Signal Name Functions

clock block power.

10 BACK BOARD CIRCUIT OPERATION

11.2. TYPICAL EXAMPLE

11.3. MPR CARD

SD card access light does not flash

The battery alarm indication light turns on

ALARM indicator flashes

ALARM indicator flashes

Optional service cards cannot start up

11.3.2. Phone Call

Noise is Heard (PAGING1)

Noise is Heard (PAGING2)