LIST OF EXPERIMENTS

Ex.No.-1 STUDY OF LOGIC GATES

AIM:
To study about logic gates and verify their truth tables.

APPARATUS REQUIRED:

SL.NO. COMPONENT SPECIFICATION QTY

1. AND GATE IC 7408 1
2. OR GATE IC 7432 1
3. NOT GATE IC 7404 1
4. NAND GATE 2 I/P IC 7400 1
5. NOR GATE IC 7402 1
6. X-OR GATE IC 7486 1
7. NAND GATE 3 I/P IC 7410 1
8. IC TRAINER KIT - 1
9. PATCH CORD - 14

THEORY:
Circuit that takes the logical decision and the process are called logic gates.
Each gate has one or more input and only one output.
OR, AND and NOT are basic gates. NAND, NOR and X-OR are known as
universal gates. Basic gates form these gates.

AND GATE:
The AND gate performs a logical multiplication commonly known as AND
function. The output is high when both the inputs are high. The output is low level
when any one of the inputs is low.

OR GATE:
The OR gate performs a logical addition commonly known as OR function.
The output is high when any one of the inputs is high. The output is low level when
both the inputs are low.

NOT GATE:
The NOT gate is called an inverter. The output is high when the input is low.
The output is low when the input is high.

AND GATE:
The NAND gate is a contraction of AND-NOT. The output is high when both
inputs are low and any one of the input is low .The output is low level when both
inputs are high.

NOR GATE:
The NOR gate is a contraction of OR-NOT. The output is high when both
inputs are low. The output is low when one or both inputs are high.
X- OR GATE:
The output is high when any one of the inputs is high. The output is low
when both the inputs are low and both the inputs are high.

PROCEDURE:
(i) Connections are given as per circuit diagram.
(ii) Logical inputs are given as per circuit diagram.
(iii) Observe the output and verify the truth table.

AND GATE

SYMBOL PIN DIAGRAM

OR GATE
 NOT GATE

SYMBOL PIN DIAGRAM

EX-OR GATE

SYMBOL PIN DIAGRAM

 2-INPUT NAND GATE

SYMBOL PIN DIAGRAM

3-INPUT NAND GATE

 NOR GATE

RESULT:

The logic gates are studied and its truth tables are verified.
Ex.No.-2 VERIFICATION OF BOOLEAN THEOREMS
USING DIGITAL LOGIC GATES

AIM:
To verify the Boolean Theorems using logic gates.

APPARATUS REQUIRED:

SL. NO. COMPONENT SPECIFICATION QTY.

1. AND GATE IC 7408 1
2. OR GATE IC 7432 1
3. NOT GATE IC 7404 1
4. IC TRAINER KIT - 1
As per
5. CONNECTING WIRES - required
THEORY:

BASIC BOOLEAN LAWS

1. Commutative Law
The binary operator OR, AND is said to be commutative if,
1. A+B = B+A
2. A.B=B.A

2. Associative Law
The binary operator OR, AND is said to be associative if,
1. A+(B+C) = (A+B)+C
2. A.(B.C) = (A.B).C

3. Distributive Law
The binary operator OR, AND is said to be distributive if,
1. A+(B.C) = (A+B).(A+C)
2. A.(B+C) = (A.B)+(A.C)

4. Absorption Law
1. A+AB = A
2. A+AB = A+B

5. Involution (or) Double complement Law

1. A = A

6. Idempotent Law
1. A+A = A
2. A.A = A
7. Complementary Law
1. A+A' = 1
2. A.A' = 0

8. De Morgan’s Theorem
1. The complement of the sum is equal to the sum of the product of the individual
complements.
A+B = A.B
2. The complement of the product is equal to the sum of the individual complements.
A.B = A+B
Demorgan’s Theorem
a) Proof of equation (1):
Construct the two circuits corresponding to the functions A’. B’and (A+B)’
respectively. Show that for all combinations of A and B, the two circuits give identical
results. Connect these circuits and verify their operations.
b) Proof of equation (2)
Construct two circuits corresponding to the functions A’+B’and (A.B)’ A.B,
respectively. Show that, for all combinations of A and B, the two circuits give identical
results. Connect these circuits and verify their operations.
We will also use the following set of postulates:
P1: Boolean algebra is closed under the AND, OR, and NOT operations.
P2: The identity element with respect to • is one and + is zero. There is no identity
element with respect to logical NOT.
P3: The • and + operators are commutative.
P4: • and + are distributive with respect to one another. That is,
A • (B + C) = (A • B) + (A • C) and A + (B • C) = (A + B) • (A + C).
P5: For every value A there exists a value A’ such that A•A’ = 0 and A+A’ = 1.
This value is the logical complement (or NOT) of A.
P6: • and + are both associative. That is, (A•B)•C = A•(B•C) and (A+B)+C = A+(B+C).
You can prove all other theorems in boolean algebra using these postulates.

PROCEDURE:

1. Obtain the required IC along with the Digital trainer kit.

2. Connect zero volts to GND pin and +5 volts to Vcc .
3. Apply the inputs to the respective input pins.
4. Verify the output with the truth table.

RESULT:
Thus the above stated Boolean laws are verified.

13
Ex.No.-2 CODE CONVERTOR

AIM:
To design and implement 4-bit
(i) Binary to gray code converter
(ii) Gray to binary code converter
(iii) BCD to excess-3 code converter
(iv) Excess-3 to BCD code converter

APPARATUS REQUIRED:
SL.NO. COMPONENT SPECIFICATION QTY.
1. X-OR GATE IC 7486 1
2. AND GATE IC 7408 1
3. OR GATE IC 7432 1
4. NOT GATE IC 7404 1
5. IC TRAINER KIT - 1
6. PATCH CORDS - 35

THEORY:

The availability of large variety of codes for the same discrete elements of
information results in the use of different codes by different systems. A conversion circuit
must be inserted between the two systems if each uses different codes for same
information. Thus, code converter is a circuit that makes the two systems compatible even
though each uses different binary code.

The bit combination assigned to binary code to gray code. Since each code uses
four bits to represent a decimal digit. There are four inputs and four outputs. Gray code is a
non-weighted code.

The input variable are designated as B3, B2, B1, B0 and the output variables are
designated as C3, C2, C1, Co. from the truth table, combinational circuit is designed. The
Boolean functions are obtained from K-Map for each output variable.

A code converter is a circuit that makes the two systems compatible even though
each uses a different binary code. To convert from binary code to Excess-3 code, the input
lines must supply the bit combination of elements as specified by code and the output lines
generate the corresponding bit combination of code. Each one of the four maps represents
one of the four outputs of the circuit as a function of the four input variables.

14
 A two-level logic diagram may be obtained directly from the Boolean expressions
derived by the maps. These are various other possibilities for a logic diagram that
implements this circuit. Now the OR gate whose output is C+D has been used to
implement partially each of three outputs.

BINARY TO GRAY CODE CONVERTOR

TRUTH TABLE:

Binary Input Gray Code Output

B3 B2 B1 B0 G3 G2 G1 G0
0 0 0 0 0 0 0 0
0 0 0 1 0 0 0 1
0 0 1 0 0 0 1 1
0 0 1 1 0 0 1 0
0 1 0 0 0 1 1 0
0 1 0 1 0 1 1 1
0 1 1 0 0 1 0 1
0 1 1 1 0 1 0 0
1 0 0 0 1 1 0 0
1 0 0 1 1 1 0 1
1 0 1 0 1 1 1 1
1 0 1 1 1 1 1 0
1 1 0 0 1 0 1 0
1 1 0 1 1 0 1 1
1 1 1 0 1 0 0 1
1 1 1 1 1 0 0 0

K-Map for G3

G3 = B3

15
K-Map for G2

K-Map for G1

K-Map for G0

16
 LOGIC DIAGRAM:

GRAY CODE TO BINARY CONVERTOR

TRUTH TABLE:

GRAY CODE BINARY CODE

G3 G2 G1 G0 B3 B2 B1 B0
0 0 0 0 0 0 0 0
0 0 0 1 0 0 0 1
0 0 1 1 0 0 1 0
0 0 1 0 0 0 1 1
0 1 1 0 0 1 0 0
0 1 1 1 0 1 0 1
0 1 0 1 0 1 1 0
0 1 0 0 0 1 1 1
1 1 0 0 1 0 0 0
1 1 0 1 1 0 0 1
1 1 1 1 1 0 1 0
1 1 1 0 1 0 1 1
1 0 1 0 1 1 0 0
1 0 1 1 1 1 0 1
1 0 0 1 1 1 1 0
1 0 0 0 1 1 1 1

17
K-Map for B3:

B3 = G3

K-Map for B2:

K-Map for B1:

18
K-Map for B0:

LOGIC DIAGRAM:

19
TRUTH TABLE: BCD TO EXCESS-3 CONVERTOR

| BCD input | Excess – 3 output |

B3 B2 B1 B0 G3 G2 G1 G0

0 0 0 0 0 0 1 1

0 0 0 1 0 1 0 0

0 0 1 0 0 1 0 1

0 0 1 1 0 1 1 0

0 1 0 0 0 1 1 1

0 1 0 1 1 0 0 0

0 1 1 0 1 0 0 1

0 1 1 1 1 0 1 0

1 0 0 0 1 0 1 1

1 0 0 1 1 1 0 0

1 0 1 0 x x x x

1 0 1 1 x x x x

1 1 0 0 x x x x

1 1 0 1 x x x x

1 1 1 0 x x x x

1 1 1 1 x x x X

K-Map for E3:

E3 = B3 + B2 (B0 + B1)
20
K-Map for E2:

K-Map for E1:

K-Map for E0:

21
 EXCESS-3 TO BCD CONVERTOR

TRUTH TABLE:

| Excess – 3 Input | BCD Output |

B3 B2 B1 B0 G3 G2 G1 G0

0 0 1 1 0 0 0 0

0 1 0 0 0 0 0 1

0 1 0 1 0 0 1 0

0 1 1 0 0 0 1 1

0 1 1 1 0 1 0 0

1 0 0 0 0 1 0 1

1 0 0 1 0 1 1 0

1 0 1 0 0 1 1 1

1 0 1 1 1 0 0 0

1 1 0 0 1 0 0 1

LOGIC DIAGRAM:

22
 EXCESS-3 TO BCD CONVERTOR

K-Map for A:

A = X1 X2 + X3 X4 X1

K-Map for B:

K-Map for C:

23
K-Map for D:

EXCESS-3 TO BCD CONVERTOR

PROCEDURE:

(i) Connections were given as per circuit diagram.

(ii) Logical inputs were given as per truth table
(iii) Observe the logical output and verify with the truth tables.

24
RESULT:

Thus the following 4-bit converters are designed and constructed.

(i) Binary to gray code converter

(ii) Gray to binary code converter
(iii) BCD to excess-3 code converter
(iv) Excess-3 to BCD code converter

25
Ex.No.-3 4-BIT ADDER AND SUBTRACTOR

AIM:

To design and implement 4-bit adder and subtractor using basic gates and MSI
device IC 7483.

APPARATUS REQUIRED:

SL.NO. COMPONENT SPECIFICATION QTY.

1. IC IC 7483 1
2. EX-OR GATE IC 7486 1
3. NOT GATE IC 7404 1
3. IC TRAINER KIT - 1
4. PATCH CORDS - 40

THEORY:

4 BIT BINARY ADDER:

A binary adder is a digital circuit that produces the arithmetic sum of two binary
numbers. It can be constructed with full adders connected in cascade, with the output carry
from each full adder connected to the input carry of next full adder in chain. The augends
bits of ‘A’ and the addend bits of ‘B’ are designated by subscript numbers from right to
left, with subscript 0 denoting the least significant bits. The carries are connected in chain
through the full adder. The input carry to the adder is C0 and it ripples through the full
adder to the output carry C4.

4 BIT BINARY SUBTRACTOR:

The circuit for subtracting A-B consists of an adder with inverters, placed between
each data input ‘B’ and the corresponding input of full adder. The input carry C 0 must be
equal to 1 when performing subtraction.

4 BIT BINARY ADDER/SUBTRACTOR:

The addition and subtraction operation can be combined into one circuit with one
common binary adder. The mode input M controls the operation. When M=0, the circuit is
adder circuit. When M=1, it becomes subtractor.

4 BIT BCD ADDER:

Consider the arithmetic addition of two decimal digits in BCD, together with an
input carry from a previous stage. Since each input digit does not exceed 9, the output sum
cannot be greater than 19, the 1 in the sum being an input carry. The output of two decimal
digits must be represented in BCD and should appear in the form listed in the columns.

32
 ABCD adder that adds 2 BCD digits and produce a sum digit in BCD. The 2
decimal digits, together with the input carry, are first added in the top 4 bit adder to
produce the binary sum.

PIN DIAGRAM FOR IC 7483:

4-BIT BINARY ADDER

LOGIC DIAGRAM:

33
4-BIT BINARY SUBTRACTOR

LOGIC DIAGRAM:

4- BIT BINARY ADDER/SUBTRACTOR

LOGIC DIAGRAM:

34
TRUTH TABLE:

Input Data A Input Data B Addition Subtraction

A4 A3 A2 A1 B4 B3 B2 B1 C S4 S3 S2 S1 B D4 D3 D2 D1
1 0 0 0 0 0 1 0 0 1 0 1 0 1 0 1 1 0
1 0 0 0 1 0 0 0 1 0 0 0 0 1 0 0 0 0
0 0 1 0 1 0 0 0 0 1 0 1 0 0 1 0 1 0
0 0 0 1 0 1 1 1 0 1 0 0 0 0 1 0 1 0
1 0 1 0 1 0 1 1 1 0 0 1 0 0 1 1 1 1
1 1 1 0 1 1 1 1 1 1 0 1 0 0 1 1 1 1
1 0 1 0 1 1 0 1 1 0 1 1 1 0 1 1 0 1

PROCEDURE:

(i) Connections were given as per circuit diagram.

(ii) Logical inputs were given as per truth table
(iii) Observe the logical output and verify with the truth tables.

RESULT:

Thus the 4-bit adder and subtractor using basic gates and MSI device IC 7483 is
designed and implemented.

35
Ex.No.-4c MAGNITUDE COMPARATOR

AIM:

To design and implement the magnitude comparator using MSI device.

APPARATUS REQUIRED:

SL.NO. COMPONENT SPECIFICATION QTY.

1. AND GATE IC 7408 2
2. X-OR GATE IC 7486 1
3. OR GATE IC 7432 1
4. NOT GATE IC 7404 1
5. 4-BIT MAGNITUDE COMPARATOR IC 7485 2
6. IC TRAINER KIT - 1
7. PATCH CORDS - 30

THEORY:

The comparison of two numbers is an operator that determine one number is greater
than, less than (or) equal to the other number. A magnitude comparator is a combinational
circuit that compares two numbers A and B and determine their relative magnitude. The
outcome of the comparator is specified by three binary variables that indicate whether
A>B, A=B (or) A<B.

A = A3 A2 A1 A0

B = B3 B2 B1 B0

The equality of the two numbers and B is displayed in a combinational circuit

designated by the symbol (A=B).

This indicates A greater than B, then inspect the relative magnitude of pairs of
significant digits starting from most significant position. A is 0 and that of B is 0.

We have A<B, the sequential comparison can be expanded as

1 1 1 1
A>B = A3B + X A B +X XAB +XXXAB
1 3 3 12 2 3 2 1 11 3 2 1 0 01
A<B = A +X A + X X2A +XXXA
3 B3 3 2 B2 3 1 B1 321 0 B0

36
 The same circuit can be used to compare the relative magnitude of two BCD
digits. Where, A = B is expanded as,

A = B = (A3 + B3) (A2 + B2) (A1 + B1) (A0 + B0)

   

x3 x2 x1 x0

PIN DIAGRAM FOR IC 7485:

8-BIT MAGNITUDE COMPARATOR

LOGIC DIAGRAM:

TRUTH TABLE:

A B A>B A=B A<B

0000 0000 0000 0000 0 1 0
0001 0001 0000 0000 1 0 0
0000 0000 0001 0001 0 0 1

37
PROCEDURE:
(i) Connections are given as per circuit diagram.
(ii) Logical inputs are given as per circuit diagram.
(iii) Observe the output and verify the truth table.

RESULT:

Thus the magnitude comparator using MSI device is designed and implemented.

43
Ex.No.-4d MULTIPLEXER AND DEMULTIPLEXER

AIM:

To design and implement the multiplexer and demultiplexer using logic gates
and study of IC 74150 and IC 74154.

APPARATUS REQUIRED:

SL.NO. COMPONENT SPECIFICATION QTY.

1. 3 I/P AND GATE IC 7411 2
2. OR GATE IC 7432 1
3. NOT GATE IC 7404 1
2. IC TRAINER KIT - 1
3. PATCH CORDS - 32

THEORY:

MULTIPLEXER:
Multiplexer means transmitting a large number of information units over a smaller
number of channels or lines. A digital multiplexer is a combinational circuit that selects
binary information from one of many input lines and directs it to a single output line. The
selection of a particular input line is controlled by a set of selection lines. Normally there
n
are 2 input line and n selection lines whose bit combination determine which input is

selected.

DEMULTIPLEXER:
The function of Demultiplexer is in contrast to multiplexer function. It takes
information from one line and distributes it to a given number of output lines. For this
reason, the demultiplexer is also known as a data distributor. Decoder can also be used as
demultiplexer.
In the 1: 4 demultiplexer circuit, the data input line goes to all of the AND gates.
The data select lines enable only one gate at a time and the data on the data input line will
pass through the selected gate to the associated data output line.

44
 4:1 MULTIPLEXER

BLOCK DIAGRAM FOR 4:1 MULTIPLEXER:

FUNCTION TABLE:
S1 S0 INPUTS Y
0 0 D0 → D0 S1’ S0’
0 1 D1 → D1 S1’ S0
1 0 D2 → D2 S1 S0’
1 1 D3 → D3 S1 S0

Y = D0 S1’ S0’ + D1 S1’ S0 + D2 S1 S0’ + D3 S1 S0

TRUTH TABLE:

S1 S0 Y = OUTPUT

0 0 D0

0 1 D1

1 0 D2

1 1 D3

45
CIRCUIT DIAGRAM FOR MULTIPLEXER:

1:4 DEMULTIPLEXER

BLOCK DIAGRAM FOR 1:4 DEMULTIPLEXER:

FUNCTION TABLE:

S1 S0 INPUT
0 0 X → D0 = X S1’ S0’
0 1 X → D1 = X S1’ S0
1 0 X → D2 = X S1 S0’
1 1 X → D3 = X S1 S0

Y = X S1’ S0’ + X S1’ S0 + X S1 S0’ + X S1 S0

46
TRUTH TABLE:

INPUT OUTPUT
S1 S0 I/P D0 D1 D2 D3
0 0 0 0 0 0 0
0 0 1 1 0 0 0
0 1 0 0 0 0 0
0 1 1 0 1 0 0
1 0 0 0 0 0 0
1 0 1 0 0 1 0
1 1 0 0 0 0 0
1 1 1 0 0 0 1

LOGIC DIAGRAM FOR DEMULTIPLEXER:

47
PIN DIAGRAM FOR IC 74150:

PIN DIAGRAM FOR IC 74154:

PROCEDURE:

(i) Connections are given as per circuit diagram.

(ii) Logical inputs are given as per circuit diagram.
(iii) Observe the output and verify the truth table.

RESULT:
Thus the multiplexer and demultiplexer using logic gates are designed and
implemented.

48
Ex.No.-5 SHIFT REGISTER

AIM:

To design and implement the following shift registers

(i) Serial in serial out
(ii) Serial in parallel out
(iii) Parallel in serial out
(iv) Parallel in parallel out

APPARATUS REQUIRED:

SL.NO. COMPONENT SPECIFICATION QTY.

1. D FLIP FLOP IC 7474 2

2. OR GATE IC 7432 1

3. IC TRAINER KIT - 1

4. PATCH CORDS - 35

THEORY:
A register is capable of shifting its binary information in one or both directions is
known as shift register. The logical configuration of shift register consist of a D-Flip flop
cascaded with output of one flip flop connected to input of next flip flop. All flip flops
receive common clock pulses which causes the shift in the output of the flip flop. The
simplest possible shift register is one that uses only flip flop. The output of a given flip flop
is connected to the input of next flip flop of the register. Each clock pulse shifts the content
of register one bit position to right.

PIN DIAGRAM OF IC 7474:

49
 SERIAL IN SERIAL OUT

LOGIC DIAGRAM:

TRUTH TABLE:

CLK Serial In Serial Out

1 1 0
2 0 0
3 0 0
4 1 1
5 X 0
6 X 0
7 X 1

SERIAL IN PARALLEL OUT

LOGIC DIAGRAM:

50
TRUTH TABLE:

OUTPUT
CLK DATA QA QB QC QD
1 1 1 0 0 0
2 0 0 1 0 0
3 0 0 0 1 1
4 1 1 0 0 1

PARALLEL IN SERIAL OUT

LOGIC DIAGRAM:

TRUTH TABLE:

CLK Q3 Q2 Q1 Q0 O/P

0 1 0 0 1 1

1 0 0 0 0 0

2 0 0 0 0 0

3 0 0 0 0 1

51
 PARALLEL IN PARALLEL OUT

LOGIC DIAGRAM:

TRUTH TABLE:

DATA INPUT OUTPUT

CLK
DA DB DC DD QA QB QC QD

1 1 0 0 1 1 0 0 1

2 1 0 1 0 1 0 1 0

PROCEDURE:
(i) Connections are given as per circuit diagram.
(ii) Logical inputs are given as per circuit diagram.
(iii) Observe the output and verify the truth table.

RESULT:
The Serial in serial out, Serial in parallel out, Parallel in serial out and
Parallel in parallel out shift registers are designed and implemented.

52
Ex.No.-6 SYNCHRONOUS AND ASYNCHRONOUS COUNTER

AIM:

To design and implement synchronous and asynchronous counter.

APPARATUS REQUIRED:

S.NO. NAME OF THE APPARATUS RANGE QUANTITY

1. Digital IC trainer kit 1
2. JK Flip Flop IC 7473 2
3. D Flip Flop IC 7473 1
4. NAND gate IC 7400 1
5. Connecting wires As required

THEORY:
Asynchronous decade counter is also called as ripple counter. In a ripple counter
the flip flop output transition serves as a source for triggering other flip flops. In other
words the clock pulse inputs of all the flip flops are triggered not by the incoming pulses
but rather by the transition that occurs in other flip flops. The term asynchronous refers to
the events that do not occur at the same time. With respect to the counter operation,
asynchronous means that the flip flop within the counter are not made to change states at
exactly the same time, they do not because the clock pulses are not connected directly to
the clock input of each flip flop in the counter.

A counter is a register capable of counting number of clock pulse arriving at its

clock input. Counter represents the number of clock pulses arrived. A specified sequence
of states appears as counter output. This is the main difference between a register and a
counter. There are two types of counter, synchronous and asynchronous. In synchronous
common clock is given to all flip flop and in asynchronous first flip flop is clocked by
external pulse and then each successive flip flop is clocked by Q or Q output of previous
stage. A soon the clock of second stage is triggered by output of first stage. Because of
inherent propagation delay time all flip flops are not activated at same time which results
in asynchronous operation.

53
PIN DIAGRAM FOR IC 7476:

CIRCUIT DIAGRAM:

TRUTH TABLE:

54
 LOGIC DIAGRAM FOR MOD - 10 RIPPLE COUNTER:

TRUTH TABLE:

CLK QA QB QC QD
0 0 0 0 0
1 1 0 0 0
2 0 1 0 0
3 1 1 0 0
4 0 0 1 0
5 1 0 1 0
6 0 1 1 0
7 1 1 1 0
8 0 0 0 1
9 1 0 0 1
10 0 0 0 0

55
PIN DIAGRAM:

SYNCHRONOUS COUNTER

LOGIC DIAGRAM:

TRUTH TABLE:

OUTPUT
CLK DATA
QA QB QC QD
1 1 1 0 0 0
2 0 0 1 0 0
3 0 0 0 1 1
4 1 1 0 0 1

56
PROCEDURE:

(i) Connections are given as per circuit diagram.

(ii) Logical inputs are given as per circuit diagram.
(iii) Observe the output and verify the truth table.

RESULT:

Thus the synchronous and asynchronous counter are designed and implemented.

57
Ex.No.- 7 IMPLEMENTATION OF BASIC LOGIC GATES

AIM:

To implement all the basic logic gates using Verilog and VHDL simulator.

LOGIC GATE SYMBOLS TRUTH TABLES

58
 VERILOG CODE

AND GATE OR GATE

module and12(a,b,c); module or12(a,b,d);
input a; input a;
input b; input b;
output c; output d;
assign c = a & b; assign d = a | b;
endmodule endmodule

NAND GATE XOR GATE

module nand12(a,b,e); module xor12(a,b,h);
input a; input a;
input b; input b;
output e; output h;
assign e = ~(a & b); assign h = a ^ b;
endmodule endmodule

XNOR GATE NOR GATE

module xnor12(a,b,i); module nor12(a,b,f);
input a; input a;
input b; input b;
output i; output f;
assign i = ~(a ^ b); assign f = ~(a | b);
endmodule endmodule

NOT GATE
module not12(a,g);
input a;
output g;
assign g = ~a;
endmodule

AND GATE

VERILOG CODE:

module and12(a,b,c);
input a;
input b;
output c;
assign c = a & b;
endmodule

59
OUTPUT WAVEFORM:

OR GATE

VERILOG CODE:

module or12(a,b,d);
input a;
input b;
output d;
assign d = a | b;
endmodule
OUTPUT WAVEFORM:

NOT GATE

VERILOG CODE:

module not12(a,g);
input a;
output g;
assign g = ~a;
endmodule

OUTPUT WAVEFORM:

60
 EX-OR GATE

VERILOG CODE:

module xor12(a,b,h);
input a;
input b;
output h;
assign h = a^ b;
endmodule

VHDL CODE:

library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;

entity xor_gate is
port (a,b : in std_logic ;
c : out std_logic);

end xor_gate;
architecture Behavioral o f xor_gate is
begin
c <= a xor b;
end Behavioral;

OUTPUT WAVEFORM:

RESULT:

Thus all the basic logic gates are implemented and verified using Verilog and VHDL
simulator.

61
 Ex.No.-8 COMBINATIONAL AND SEQUENTIAL CIRCUITS

AIM:

To simulate the sequential and combinational circuits using HDL simulator (Verilog
and VHDL).

1. HALF ADDER

Truth Table

Input Output
A B S(Sum) C(Carry)
0 0 0 0
0 1 1 0
1 0 1 0
1 1 1 1

Circuit Diagram Graphical Notation

Equations
S (Sum) =A^B
C (Carry) =AB

Verilog Code:

module hadd(a,b,s,c); input a;

input b;
output s;
output c;
assign s = a ^ b;
assign c = a & b;
endmodule

Output:

VHDL Code:

library IEEE;
62
 use IEEE.STD_LOGIC_1164.ALL; use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL; entity halfadder is
port(
a : in std_logic; b : in std_logic;
sum : out std_logic; carry : out std_logic );
end halfadder;
architecture Behavioral of halfadder is begin
sum <= (a xor b); carry <= (a and b); end Behavioral;

Input:
a:1;
b :1;
Sum : 0
Carry : 1
Output:

2. FULL ADDER

Truth Table

Input Output
A B C SUM Cout
0 0 0 0 0
0 0 1 1 0
0 1 0 1 0
0 1 1 0 1
1 0 0 1 0
1 0 1 0 1
1 1 0 0 1
1 1 1 1 1

63
 K- Map for sum K-map for Carry

H.ADDER SUM = A’B’C + A’BC’ + AB’C’ + ABC Cout = A’BC + AB’C + ABC’ +ABC
SUM= A^B^C Cout= (A^B)C+AB

Circuit Diagram:

Verilog Code:

module fadd(a,b,c,s,cout);
input a;
input b;
input c; output s;
output cout;
assign s = (a ^ b) ^ c;
assign cout = (a & b)|( b & c)|(c & a);
endmodule

Output :

64
 VHDL Code:

library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
entity fulladder is
port(
a : in std_logic;
b : in std_logic;
cin : in std_logic;
sum : out std_logic;
carry : out std_logic
);
end fulladder;
architecture Behavioral of fulladder is
begin
sum <= (a xor b xor cin);
carry <= (a and b) or (b and cin) or (a and cin);
end Behavioral;

Output:

3. HALF SUBTRACTOR

Verilog Code:

module hsub(a,b,d,bor);
Input a;
Input b;
output d;
output bor;
assign d=)a^b);
assign bor = (~a&~b);
end module

VHDL Code:

library IEEE;
65
 use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
entity halfsubtractor is
port(
a : in std_logic;
b : in std_logic;
dif : out std_logic;
bor : out std_logic
);
end halfsubtractor;
architecture Behavioral of halfsubtractor is
begin
dif <= a xor b;
bor <= ((not a) and b);
end Behavioral;

Output:

4. FULL SUBTRACTOR

Verilog Code:
module sub(a,b,c,d,b out);
input a;
input b;
input c;
output d;
output bout;
assign d = (a ^ b) ^ c;
assign bout = (~a & b)|( b & c)|(c & ~a);
endmodule

Output:

66
 VHDL Code:

library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
entity fullsubtractor is
port( a : in std_logic;
b : in std_logic;
cin : in std_logic;
dif : out std_logic;
bor : out std_logic );
end fullsubtractor;
architecture Behavioral of fullsubtractor is begin
dif <= a xor b xor cin;
bor <= (((not a) and b) or (( not a) and cin) or (b and cin));
end Behavioral;

INPUT:
a:0;
b :0;
Cin : 1
Difference : 1
Borrow : 1

Output:

5. MULTIPLEXER

Verilog Code:

module mux4to1(Y, I0,I1,I2,I3, sel);

output Y;
input I0,I1,I2,I3;
input [1:0] sel;
reg Y;
always @ (sel or I0 or I1 or I2 or I3)
case (sel)
67
 2'b00:Y=I0;
2'b01:Y=I1;
2'b10: Y=I2;
2'b11: Y=I3;
endcase
endmodule

Output:

VHDL Code:

library IEEE;
use IEEE.STD_LOGIC_1164.ALL; use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL; entity mux is
port(
inp : in std_logic_vector(3 downto 0); sel : in std_logic_vector(1 downto 0); muxout
: out std_logic --mux output line );
end mux;
architecture Behavioral of mux is begin
process(inp,sel) begin
case sel is when "00" =>
muxout <= inp(0); -- mux O/P=1 I/P-- when "01" =>
muxout <= inp(1); -- mux O/P=2 I/P-- when "10" =>
muxout <= inp(2); -- mux O/P=3 I/P-- when "11" =>
muxout <= inp(3); -- mux O/P=4 I/P-- when others =>
end case; end process;
end Behavioral;

Truth Table:

68
6. DEMULTIPLEXER

Verilog Code:

module demux(S,D,Y);
Input [1:0] S;
Input D;
Output [3:0] Y; reg Y;
always @(S OR )
case({D,S})
3’b100: Y=4’b0001;
3’b101: Y=4’b0010;
3’b110: Y=4’b0100;
3’b111: Y=4’b1000;
default:Y=4’b0000;
endcase
endmodule

VHDL Code:

library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
entity demux is
port(
dmuxin : in std_logic;
sel : in std_logic_vector(1 downto 0);
oup : out std_logic_vector(3 downto 0)
);
end demux;
architecture Behavioral of demux is
begin
process(dmuxin,sel)
begin
case sel is
when "00" =>
oup(0) <= dmuxin; --1 dmux o/p = dmux i/p--
oup(1) <= '0';
oup(2) <= '0';
oup(3) <= '0';
when "01" =>
oup(0) <= '0';
oup(1) <= dmuxin; --2 dmux o/p = dmux i/p--
oup(2) <= '0';
oup(3) <= '0';
when "10" =>
69
oup(0) <= '0';
oup(1) <= '0';
oup(2) <= dmuxin; --3 dmux o/p = dmux i/p--
oup(3) <= '0';
when "11" =>
oup(0) <= '0';
oup(1) <= '0';
oup(2) <= '0';
oup(3) <= dmuxin; --4 dmux o/p = dmux i/p--
when others =>
end case;
end process;
end Behavioral;

Truth Table:

Output:

7. D FLIPFLOP
VHDL Code:

library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
entity dff is

70
port(
clk : in std_logic; --clock input
rst : in std_logic; --active low,synchronous reset
d : in std_logic; --d input
q,qbar : out std_logic --flip flop outputs ie,Qn+1 and its complement
);
end dff;
architecture Behavioral of dff is
begin
process(clk,rst)
begin
if rising_edge(clk) then
if (rst = '0') then --active low,synchronous reset
q <= '0';
qbar <= '1';
else
q <= d;
qbar <= not(d);
end if;
end if;
end process;
end Behavioral;

Output:

8. T FLIPFLOP
Verilog Code :
module tffeq(t,rst, clk,qp, qbar); input t,rst, clk;
output qp, qbar; wire q;
reg qp;
always @ (posedge clk) if (rst)
qp=0; else
qp = q ^ t; assign qbar = ~ qp;
endmodule

71
 9. JK FLIPFLOP
Verilog Code:

module jkff(jk,pst,clr,clk,qp,qbar);
input [1:0] jk;
input pst,clr,clk;
output qp,qbar;
reg qp;
wire q;
always @ (posedge clk) if (pst)
qp= 1;
else
begin
if (clr)
qp= 0;
else
begin
case (jk)
2'b00: qp=q;
2'b01 : qp = 1'b0;
2'b10 : qp =1'b1;
2'b11 : qp = ~q;
default qp =0;
endcase
end
end
assign qbar = ~q;
assign q = qp;
endmodule

Output:

10. RIPPLE COUNTER

Verilog Code:

module ripple(clkr,st,,t,A,B,C,D);
input clk,rst,t;
output A,B,C,D;
Tff T0(D,clk,rst,t);
Tff T1(C,clk,rst,t);
Tff T2(B,clk,rst,t);

72
Tff T3(A,clk,rst,t);
endmodule
module Tff(q,clk,rst,t);
input clk,rst,t;
output q;
reg q;
always @(posedge clk)
begin
if(rst)
q<=1’b0; else
if(t)
q<=~q;
end
endmodule

VHDL Code:

library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
---- Uncomment the following library declaration if instantiating
---- any Xilinx primitives in this code.
--library UNISIM;
--use UNISIM.VComponents.all;
entity counter is
Port ( rst : in STD_LOGIC;
clk : in STD_LOGIC;
led : out std_logic_vector(3 downto 0)
);
end counter;
architecture Behavioral of counter is
signal reg :std_logic_vector(3 downto 0);
begin
process(rst,clk)
begin
if rst = '1' then
reg <= "0000";
elsif rising_edge(clk) then
reg <= reg + 1;
end if;
end process;
led(3 downto 0) <= reg(3 downto 0);
end Behavioral;

73
 Output:

11. UPDOWN COUNTER

Verilog Code:

module updowncount (R, Clock, clr, E, up_down, Q);

parameter n = 4;
input [n-1:0] R;
input Clock, clr, E, up_down;
output [n-1:0] Q;
reg [n-1:0] Q;
integer direction;
always @(posedge Clock)
begin
if (up_down) direction = 1;
else direction = -1;
if (clr) Q <= R;
else if (E) Q <= Q + direction;
end
endmodule

UP Counter:

74
 DOWN Counter:

12. SHIFT REGISTER

a. Serial In Serial Out

VHDL Code:

library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
--library UNISIM;
--use UNISIM.VComponents.all;
entity hj is
port(
clk : in std_logic;
rst : in std_logic;
si: in std_logic;
so: out std_logic
);
end hj;
architecture Behavioral of hj is
signal temp : std_logic_vector(3 downto 0);
begin
process(clk,rst)
begin
if rising_edge(clk) then
if rst = '1' then
temp <= (others=>'0');
else
temp <= temp(2 downto 0) & si;
end if;
end if;
end process;
so <= temp(3);
end Behavioral;

Output:
75
b. Parallel In Parallel Out

VHDL Code:
library IEEE;
use IEEE.STD_LOGIC_1164.ALL;
use IEEE.STD_LOGIC_ARITH.ALL;
use IEEE.STD_LOGIC_UNSIGNED.ALL;
--library UNISIM;
--use UNISIM.VComponents.all;
entity hj is
port(
clk : in std_logic;
rst : in std_logic;
po: out std_logic_vector(3 downto 0);
pi: in std_logic_vector(3 downto 0)
);
end hj;
architecture Behavioral of hj is
signal temp : std_logic_vector(3 downto 0);
begin
process(clk,rst)
begin
if rising_edge(clk) then
if rst = '1' then
temp <= (others=>'0');
else
temp <= pi(3 downto 0);
end if;
end if;
end process;
po <= temp(3 downto 0);
end Behavioral;

Output:

76
RESULT:

Thus the sequential and combinational circuits are designed and implemented using
HDL simulator (Verilog and VHDL).

77