Technical Data TD

ROTANODE
E7252X
E7252FX 0197
E7252GX

Rotating Anode X-Ray Tube Housing Assembly

High speed rotating anode X-ray tube housing

assembly for high energy radiographic and
cine-fluoroscopic operations.

The heavy anode is constructed with specially

processed rhenium-tungsten faced
molybdenum target which is 74 mm diameter
and has an improved coating to increase
thermal emissivity.

These tubes have foci 1.2 mm and 0.6 mm,

and are available for a maximum tube voltage
150 kV with Three-phase generator.

Accommodated with IEC60526 type

high-voltage cable receptacles.

General Data

IEC Classification .............................................................................................................. ClassⅠ

Electrical:
Circuit (Center-grounded) ................................................................... Three-phase full-wave rectified
Nominal Tube Voltage:
Radiographic ..................................................................................................... 40 ~ 150 kV Max.
Fluoroscopic ...................................................................................................... 40 ~ 125 kV Max.
Nominal Focal Spot Value:
Large Focus ...................................................................................................................... 1.2 mm
Small Focus ...................................................................................................................... 0.6 mm
Nominal Anode Input Energy (at 0.1s):
Large Focus ........................................................................................................................ 75 kW
Small Focus ........................................................................................................................ 27 kW

★The information contained herein is presented only as a guide for the applications of our products.
No Responsibility is assumed by TOSHIBA ELECTRON TUBES & DEVICES CO.,LTD.(TETD) for any infringements of patents or other rights of the
third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TETD or others.
★The information contained herein may be changed without prior notice. It is therefore advisable to contact TETD before proceeding with the design of
equipment incorporating this product.
★For further particulars apply to TETD.

No. TE-E7252X/FX/GX 2005-08-23

E7252X / E7252FX / E7252GX

Motor Ratings:
Stator: XS-AL
Duty Starting Running
2) 2)
Power source (Hz) 180 60 180 60
Input power (W) 1100 910 83 83
4)
Voltage (V) 220 130 60 40
Current (A) 5.7 7.8 1.6 2.3
1) 5)
Min. Speed up (s) 1.2 0.8 - -
Capacitor (µF) 6 44 6 44
2)
Min. Braking (s) 3 / 90 V (DC)
Stator impedance:
Common-Main Winding ......................................................................................................... 9.4 Ω
Common-Auxiliary Winding.................................................................................................. 28.3 Ω

Stator: XS-R
Duty Starting Running
3) 3)
Power source (Hz) 180 50/60 180 50/60
Input power (W) 2300 1450 300 80
4)
Voltage (V) 460 240 130 58
Current (A) 5.4 6.5 2.0 1.5
1) 5)
Min. Speed up (s) 1.0 0.6 - -
Capacitor (µF) 3 24 3 24
2) 3)
Min. Braking (s) 1.5 / 90 V (DC)
Note 1) The speed up time from normal speed of 3000 min-1 (3600 min-1) to high speed of
10800 min-1 is 2/3 times of the specified speed up time from 0 to high speed, which is
described on motor rating table.
2) To be applied for high speed rotation.
3) To be obtained with AID starter Model 60/180.
4) The every applied voltage must be never exceeded 110% of the above specification.
5) The speed-up time is allowed up to 110% of the above specification.
Stator impedance:
Common-Main Winding ....................................................................................................... 27.5 Ω
Common-Auxiliary Winding.................................................................................................. 58.0 Ω

Anode Speed:
50 Hz ................................................................................................................... 2700 min-1 Min.
60 Hz ................................................................................................................... 3200 min-1 Min.
180 Hz ................................................................................................................... 9700 min-1 Min.
Resistance between Housing and Low Voltage Terminals ................................................ 2 MΩ Min.
Normal operating range of the housing temperature .......................................................... 16 ~ 75 °C

-2-
 E7252X / E7252FX / E7252GX

Mechanical:
Dimensions: ................................................................................................. See dimensional outline
Overall Length .................................................................................................................. 476 mm
Maximum Diameter ....................................................................................................... 152.4 mm
Target:
Angle ........................................................................................................................... 12 degrees
Diameter ............................................................................................................................ 74 mm
Construction .................................................................... Rhenium-Tungsten faced Molybdenum
Permanent Filtration ............................................................... 0.9 mm Al / 75 kV IEC60522 / 2003
Radiation Protection (To meet the requirements of IEC 60601-1-3):
Leakage Technique Factor ................................................................................. 150 kV 3.4 mA
X-ray Coverage .................................................................................. 354 × 354 mm at SID 835 mm
Weight (Approx.) ........................................................................................................................ 18 kg
High Tension Terminals ...................................................... To meet the requirements of IEC 60526
Cooling Method .................................................................................................. Natural or forced air
Tube Housing Model Number:
E7252X .......................................................................................................................... XH-106V
E7252FX ........................................................................................................................ XH-180
E7252GX ......................................................................................................................... XH-181

-3-
E7252X / E7252FX / E7252GX

Absolute Maximum and Minimum Ratings

(At any time, these values must not be exceeded.)

Maximum Tube Voltage:

Radiographic ...................................................................................................................... 150 kV
Fluoroscopic ....................................................................................................................... 125 kV
Maximum Voltage to Ground .................................................................................................... 78 kV
Minimum Tube Voltage ............................................................................................................. 50 kV
Maximum Tube Current:
Large Focus .................................................................................................................... 1000 mA
Small Focus ...................................................................................................................... 400 mA
Maximum Filament Current:
Large Focus .......................................................................................................................... 5.5 A
Small Focus .......................................................................................................................... 5.2 A
Filament Voltage:
Large Focus (At max. filament current 5.5 A) .......................................................... 12.7 ~ 17.1 V
Small Focus (At max. filament current 5.2 A) ............................................................... 7.0 ~ 9.4 V
Filament Frequency Limits ................................................................................................ 0 ~ 25 kHz
Average Input Power ............................................................................................ 142 W (200 HU/s)
(Fluoroscopic, repeated radiographic or mixed exposure)
Thermal Characteristics:
Anode Heat Content ......................................................................................... 210 kJ (300 kHU)
Maximum Anode Heat Dissipation Rate .......................................................... 475 W (667 HU/s)
X-ray Tube Assembly Heat Content ................................................................ 900 kJ (1250 kHU)
Maximum Housing Heat Dissipation Rate:
Without Air-circulator ................................................................................ 200 W (16 kHU/min)

-4-
 E7252X / E7252FX / E7252GX

Environmental Limits

Operating Limits:
Temperature ................................................................................................................ 10 ~ 40 ℃
Humidity ........................................................................................................................ 30 ~ 85 %
(No condensation)
Atmospheric Pressure .............................................................................................. 70 ~ 106 kPa
Shipping and Storage Limits:
Temperature .............................................................................................................. -20 ~ 70 ℃
Humidity ........................................................................................................................ 20 ~ 90 %
(No condensation)
Atmospheric Pressure .............................................................................................. 50 ~ 106 kPa

-5-
E7252X / E7252FX / E7252GX

The information about EMC conformity (IEC60601-1-2 Ed2/2001)

As the result of reviewing the test requirements in the following Tables, an X-ray tube assembly
as a component of X-ray system or apparatus does not fall within the scope of the EMC directive of
IEC60601-1-2: 2001. Therefore, X-ray system manufacturer shall conduct the required test and
evaluate EMC.

CAUTION: The diagnostic X-ray system can only allow to use the designated cables and
components. If the different cables or components are used, they may deteriorate
the performance of electromagnetic emissions and immunity.

The following tables are the copies of statements in IEC60601-1-2: 2001

Table 1 – Guidance and manufacturer’s declaration – electromagnetic emissions –

for all EQUIPMENT and SYSTEMS (see 6.8.3.201 a) 3))

Guidance and manufacturer’s declaration – electromagnetic emissions

The [EQUIPMENT or SYSTEM] is intended for use in the electromagnetic environment specified
below. The customer or the user of the [EQUIPMENT or SYSTEM] should assure that it is used
in such an environment.
Emission test Compliance Electromagnetic environment - guidance
RF emissions The [EQUIPMENT or SYSTEM] uses RF energy only
CISPR 11 for its internal function. Therefore, its RF emissions are
Group 1
very low and are not likely to cause any interference in
nearby electronic equipment.
RF emissions The [EQUIPMENT or SYSTEM] must emit
CISPR 11 electromagnetic energy in order to perform its intended
Group 2
function. Nearby electronic equipment may be
affected.
RF emissions
Class [A or B]
CISPR 11
Harmonic
Class [A, B, C, D, or
emissions
Not applicable]]
IEC 61000-3-2
Voltage
fluctuations/ [Complies or Not
flicker emissions applicable]
IEC 61000-3-3
The [EQUIPMENT or SYSTEM] is suitable for use in
all establishments, including domestic establishments
[See 6.8.3.2001 a]
and those directly connected to the public low-voltage
3) and Figure 201]
power supply network that supplies buildings used for
domestic purposes.
The [EQUIPMENT or SYSTEM] is suitable for use in
all establishments other than domestic and these
[See 3.8.3.201 a] 3)
directly connected to the public low-voltage power
and Figure 201
supply network that supplies buildings used for
domestic purposes.
RF emissions The [EQUIPMENT] is not suitable for interconnection
Complies
CISPR 14-1 with other equipment.
RF emissions The [EQUIPMENT] is not suitable for interconnection
Complies
CISPR 15 with other equipment.

-6-
 E7252X / E7252FX / E7252GX

Table 2 – Guidance and manufacturer’s declaration – electromagnetic immunity –

for all EQUIPMENT and SYSTEMS (see 6.8.3.201 a) 6))

Guidance and manufacturer’s declaration – electromagnetic immunity

The [EQUIPMENT or SYSTEM] is intended for use in the electromagnetic environment specified
below. The customer or the user of the [EQUIPMENT or SYSTEM] should assure that it is used
in such an environment.
IEC 60601 Compliance Electromagnetic environment –
Immunity test
test level level guidance
Electrostatic ±6 kV contact Floors should be wood, concrete or
discharge (ESD) ±8 kV air ceramic tile. If floors are covered with
IEC 61000-4-2 synthetic material, the relative
humidity should be at least 30 %.
Electrical fast ±2 kV for power Mains power quality should be that of
transient/burst supply lines a typical commercial or hospital
IEC 61000-4-4 ±1 kV for environment.
input/output lines
Surge ±1 kV differential Mains power quality should be that of
IEC 61000-4-5 mode a typical commercial or hospital
±2 kV common environment.
mode
Voltage dips, short ＜5 % UT Mains power quality should be that of
interruptions and (＞95 % dip in UT ) a typical commercial or hospital
voltage variations for 0.5 cycle environment. If that user of the
on power supply [EQUIPMENT or SYSTEM] requires
input lines. 40 % UT continued operation during power
IEC 61000-4-11 (60 % dip in UT ) mains interruptions, it is
for 5 cycle recommended that the [EQUIPMENT
or SYSTEM] be powered from an
70 % UT uninterruptible power supply or a
(30 % dip in UT ) battery.
for 25 cycle

＜5 % UT
(＞95 % dip in UT )
for 5 sec
Power frequency 3 A/m Power frequency magnetic fields
(50/60 Hz) should be at levels characteristic of a
magnetic field typical location in a typical
IEC 61000-4-8 commercial or hospital environment.
NOTE UT is the a.c. mains voltage prior to application of the test level.

-7-
E7252X / E7252FX / E7252GX

Table 3 – Guidance and manufacturer’s declaration – electromagnetic immunity –

for LIFE-SUPPORTING EQUIPMENT and SYSTEM (see 6.8.3.201 b))

Guidance and manufacturer’s declaration - electromagnetic immunity -

The [EQUIPMENT or SYSTEM] is intended for use in the electromagnetic environment specified
below. The customer or the user of the [EQUIPMENT or SYSTEM] should assure that it is used
such an environment.
IEC60601 test Compliance
Immunity test Electromagnetic environment - guidance
level level
Portable and mobile RF communications
equipment should be used no closer to any
part of the [EQUIPMENT or SYSTEM],
including cables, than the recommended
separation distance calculated from the
equation applicable to the frequency of the
transmitter.

Recommended separation distance

Conducted RF 3 Vrms [V1] V d = [

3 .5
] P
IEC61000-4-6 150 kHz to 80 MHz V1
outside ISM bandsa

10 Vrms [V2] V d = [
12
] P
150 kHz to 80 MHz V 2
in ISM bandsa

Radiated RF 10 V/m [E1] V/m d = [

12
] P 80 MHz to 800 MHz
IEC61000-4-3 80 MHz to 2.5GHz E1

23
d = [ ] P 800 MHz to 2.5 GHz
E1
Where P is the maximum output power
rating of the transmitter in watts (W)
according to the transmitter manufacturer
and d is the recommended separation
distance in meters (m).b
Field strengths from fixed RF transmitters,
as determined by an electromagnetic site
survey,c should be less than the
compliance level in each frequency ranged.
Interference may occur in the vicinity of
equipment marked with the following
symbol:

Continued to the next page.

-8-
 E7252X / E7252FX / E7252GX

Note: 1 At 80 MHz and 800 MHz, the higher frequency range applies.
2 These guidelines may not apply in all situations. Electromagnetic propagation is affected
by absorption and reflection from structures, object and people.
a
The ISM (industrial, scientific and medical) bands between 150kHz and 80MHz are 6,765MHz
to 6,795MHz; 13,553MHz to 13,567MHz; 26,957MHz to 27,283MHz; and 40.66MHz to
40.70MHz.
b
The compliance levels in the ISM frequency bands between 150kHz and 80MHz and in the
frequency range 80MHz to 2.5GHz are intended to decrease the likelihood that
mobile/portable communications equipment could cause interference if it is inadvertently
brought into patient areas. For this reason, an additional factor of 10/3 is used in calculating
the recommended separation distance for transmitters in these frequency ranges.
c
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the [EQUIPMENT or
SYSTEM] is used exceeds the applicable RF compliance level above, the [EQUIPMENT or
SYSTEM] should be observed to verify normal operation. If abnormal performance is
observed, additional measures may be necessary, such as reorienting or relocating the
[EQUIPMENT or SYSTEM].
d
Over the frequency range 150kHz to 80MHz, field strengths should be less [V1] v/m.

-9-
E7252X / E7252FX / E7252GX

Table 4 – Guidance and manufacturer’s declaration – electromagnetic immunity –

for EQUIPMENT and SYSTEM that are not LIFE-SUPPORTING (see 6.8.3.201 b))

Guidance and manufacturer’s declaration - electromagnetic immunity -

The [EQUIPMENT or SYSTEM] is intended for use in the electromagnetic environment specified
below. The customer or the user of the [EQUIPMENT or SYSTEM] should assure that it is used
in such an environment.
IEC60601 test Compliance
Immunity test Electromagnetic environment - guidance
level level
Portable and mobile RF communications
equipment should be used no closer to any
part of the [EQUIPMENT or SYSTEM],
including cables, than the recommended
separation distance calculated from the
equation applicable to the frequency of the
transmitter.
Recommended separation distance
3 .5
Conducted RF 3 Vrms [V1] V d = [ ] P
V1
IEC61000-4-6 150 kHz to 80 MHz
3 .5
Radiated RF 3 V/m [E1] V/m d = [ ] P 80 MHz to 800 MHz
E1
IEC61000-4-3 80 MHz to 2.5GHz
7
d = [ ] P 800 MHz to 2.5 GHz
E1

Where P is the maximum output power

rating of the transmitter in watts (W)
according to the transmitter manufacturer
and d is the recommended separation
distance in meters (m).
Field strengths from fixed RF transmitters,
as determined by an electromagnetic site
survey,a should be less than the
compliance level in each frequency rangeb.
Interference may occur in the vicinity of
equipment marked with the following
symbol:

Note: 1 At 80MHz and 800MHz, the higher frequency range applies.

2 These guidelines may not apply in all situations. Electromagnetic propagation is affected
by absorption and reflection from structures, object and people.
a
Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the [EQUIPMENT or
SYSTEM] is used exceeds the applicable RF compliance level above, the [EQUIPMENT or
SYSTEM] should be observed to verify normal operation. If abnormal performance is
observed, additional measures may be necessary, such as reorienting or relocating the
[EQUIPMENT or SYSTEM].
b
Over the frequency range 150kHz to 80MHz, field strengths should be less [V1] v/m.

- 10 -
 E7252X / E7252FX / E7252GX

Warning

Warning to Interface with X-ray Generator

1. Housing Rupture
Never input over-rated power to x-ray tube assembly.
If the input power is extremely higher than specification, it may cause the over temperature of
anode, insert tube glass shatter and ultimately the following serious problems due to generating
over-pressure by oil vaporization inside housing assembly.
In such a critical condition, the safety thermal switch can not protect x-ray tube even if it works.

* Housing sealing parts rupture

* Human injury including burns due to hot oil escape
* Fire accident due to flaming anode target

We strongly request that the x-ray generator should have a protective function which manages
input power to x-ray tube assembly.

- 11 -
E7252X / E7252FX / E7252GX

Cautions

Caution to Interface with X-ray Generator

1. Over Rating
X-ray tube assembly can be broken with applying just one over rated shot.
Please read the technical data sheets carefully and follow the instructions.

2. Permanent Filtration
The total filtration and the distance between x-ray focal spot and human body are regulated legally.
They should be complied with the regulation.

3. Safety Thermal Switch

X-ray tube assembly has safety thermal switch to prohibit further input power when the tube
housing reaches to the temperature of switch-open.
The switch should be hooked up with the x-ray generator which control output power to x-ray tube
assembly.
The switch is not recommended connecting stator coil in series circuit.
Even if the switch works, never turn the system power off and the cooling unit should be activated.

4. Unexpected Malfunction
X-ray tube assembly may have the risk to be unexpectedly malfunctioning due to life termination or
failure. If the serious problems caused by the above risk is expected, we recommend to have a
contingency plan to avoid such a case.

5. New Application
If you use the product with new application not to be mentioned in this specification or with different
type of x-ray generator, please contact to us for confirming its availability.

- 12 -
 E7252X / E7252FX / E7252GX

Caution for Installation, Adjustment and Maintenance

1. Qualified Persons
Only qualified persons who have technical training and professional knowledge can handle x-ray
tube assembly.

2. Fragile Glass
X-ray tube is assembled with glass, therefore, it can be broken with the mechanical vibration or
pulsed shock over 19.6m/s2 (2G).
Careful handling is required to treat or transport.

3. Ground Terminal
X-ray tube assembly has ground terminal. Ground cable should be connected.

4. High Voltage
All x-ray tubes operate at voltages high enough to kill through electrical shock. Never touch the
high voltage delivered plugs or terminals.
When direct access to such parts is required, the primary circuit should be disabled and high
voltage capacitors/cables discharged.

5. High Voltage Plug

High voltage plug should be cleaned up and free from any physical damages. Silicon compound
application is required for high voltage stability.

6. Operation Atmosphere
X-ray tube assembly is not allowed to use in the atmosphere of flammable or corrosive gas.

7. Protective Cover
X-ray tube assembly is not allowed to use without the protective cover attached.

8. Handling
Appropriate jig or tools are required for tube installation to avoid physical damages.

9. Returning Tube
X-ray tube assembly should be repackaged with the original material when it is returned back for
quality examination in our factory.
Be careful to put the tube upside cathode. If the packaging is not proper, the tube may not be
correctly examined.

- 13 -
E7252X / E7252FX / E7252GX

Caution in Operation

1. X-Ray Radiation
X-ray tube assembly should have the beam limiting equipment mounted on the x-ray port to protect
unnecessary radiation.

2. Dielectric Oil
X-ray tube assembly has dielectric oil contained for high voltage stability. As it is poisonous for
human health, if it is exposed to the non-restricted area, it should be disposed as following to the
local regulation.

3. Operation Atmosphere
X-ray tube assembly is not allowed to use in the atmosphere of flammable or corrosive gas.

4. Lead Disposition
X-ray tube housing is lined with lead to protect unnecessary radiation. As the lead powder or vapor
is harmful for human health, it should be disposed as following to the local regulation or returned
back to us with your cost of transportation. We dispose it in our facility with free of charge.

5. X-ray tube housing temperature

Do not touch on X-ray tube housing surface just after operation due to high temperature.
Stay X-ray tube to be cooled.

6. Any Malfunction
Please contact to your system service person immediately, if any malfunction is noticed.

- 14 -
 E7252X / E7252FX / E7252GX

Caution Label

(a) This label is a caution label to notify the user of the following point.
"Housing end cap is used to protect the electric shock and x-ray leakage."

Attachment position : X-ray tube assembly housing end cap

- 15 -
E7252X / E7252FX / E7252GX

Maximum Rating Charts

(Absolute Maximum Rating Charts)

Conditions : Tube Voltage Three-Phase

Stator Power Frequency 180Hz

Focal Spot : 1.2 mm Focal Spot : 0.6 mm

80kV 70kV 60kV 50kV 70kV 60kV

1000 400
90kV 80kV
900 50kV
100kV 350
40kV 90kV
800 110kV
40kV
300 100kV
TUBE CURRENT [mA]

TUBE CURRENT [mA]

700 125kV 110kV
250 125kV
600 150kV

500 200 150kV

400
150
300
100
200
50
100

0 0
0.01 0.03 0.1 0.2 0.3 0.5 1 2 3 5 10 0.01 0.03 0.1 0.2 0.3 0.5 1 2 3 5 10
0.02 0.05 0.02 0.05
EXPOSURE TIME [s] EXPOSURE TIME [s]

Conditions : Tube Voltage Three-Phase

Stator Power Frequency 60Hz

Focal Spot : 1.2 mm Focal Spot : 0.6 mm

60kV 50kV 40kV 50kV 40kV
800 300
60kV
700 70kV
250 70kV
600 80kV
TUBE CURRENT [mA]

80kV
TUBE CURRENT [mA]

90kV 200
500 100kV 90kV
110kV 100kV
110kV
400 125kV 150
125kV
150kV
300 150kV
100
200

50
100

0 0
0.01 0.03 0.1 0.2 0.3 0.5 1 2 3 5 10 0.01 0.03 0.1 0.2 0.3 0.5 1 2 3 5 10
0.02 0.05 0.02 0.05
EXPOSURE TIME [s] EXPOSURE TIME [s]

- 16 -
 E7252X / E7252FX / E7252GX

Emission & Filament Characteristics

Three-Phase

Focal Spot : 1.2 mm

1000 16
100kV
900 125kV
800 150kV 14

FILAMENT VOLTAGE [V]

TUBE CURRENT [mA]

700

600 12
Ef
500
80kV
400 10
60kV
300
40kV
200 8

100

0 6
3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5

FILAMENT CURRENT [A]

Focal Spot : 0.6 mm

400 10
100kV

125kV
FILAMENT VOLTAGE [V]

300 8
TUBE CURRENT [mA]

150kV

Ef
200 6

80kV
100 4
60kV

40kV

0 2
3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2

FILAMENT CURRENT [A]

- 17 -
E7252X / E7252FX / E7252GX

Thermal Characteristics
Housing Thermal Characteristics
900
200W
800

700
HEAT STORAGE [kJ]

600

500

400
COOLING

300

200

100
HEATING
0
0 60 120 180 240 300 360

TIME [min]

Anode Thermal Characteristics

210
200 475W(667HU/S)

180 COOLING

160
HEAT STORAGE [kJ]

140

120

100

80

60

40
HEATING
20

0
0 2 4 6 8 10 12
TIME [min]
The heating curves are showing examples of
average input power to the anode in operation.

- 18 -
 E7252X / E7252FX / E7252GX

Dimensional Outline of E7252X

Unit mm

140

90
2-M63.5
P=1.27
ANODE
4-M6 8 DEEP

CENTRAL RAY AND REFERENCE AXIS

152.4
11.1

146.5

12°
90
50.8

476
134.5
4-M5 10 DEEP

90 S
L
11.1

CATHODE
105

TERMINAL CONNECTIONS
18.28

9 8 7 6 5 1 2 3 4 E
FOCAL SPOT
NC NC NC NC
10°

53

M A
81

ET
TEMPERATURE RELAY
192

(NORMALLY CLOSED)
Note) Do not connect terminal No.1 and No.5 or 6
in series circuit.
70

CENTRAL OF FOCAL SPOT

A

71
B
191
A：±1.5mm，B：±1.5mm
C : COMMON NC : NON-CONNECTION
L : LARGE FOCUS ET : EARTH TERMAINAL
S : SMALL FOCUS : CENTERAL X-RAY
M : MAIN WINDING OF THE STATOR ANODE & CATHODE TERMINAL
A : AUX. WINDING OF THE STATOR : IEC 60526 TYPE

- 19 -
E7252X / E7252FX / E7252GX

Dimensional Outline of E7252FX

Unit mm

φ140

90
ANODE

CENTRAL RAY AND REFERENCE AXIS

2-M63.5
P=1.27
φ152.4

146.5
4-M6 8DEEP

11.1
12°

50.8
476

90
φ
92
45°
134.5

4-M5 10DEEP

90
C
11.1

CATHODE

L
105

TERMINAL CONNECTIONS

18.28
FOCAL SPOT
10°
9 8 7 6 5 1 2 3 4 E

NC NC NC NC 53
M A 81

ET 192
TEMPERATURE RELAY
(NORMALLY CLOSED)
Note) Do not connect terminal No.1 and
φ70

No.5 or 6 in series circuit.

CENTRAL OF FOCAL SPOT

A

71

B 191

A：±1.5mm，B：±1.5mm

C : COMMON NC : NON-CONNECTION
L : LARGE FOCUS ET : EARTH TERMINAL
S : SMALL FOCUS : CENTRAL X-RAY
M : MAIN WINDING OF THE STATOR ANODE & CATHODE TERMINAL
A : AUX. WINDING OF THE STATOR : IEC60526 TYPE

- 20 -
 E7252X / E7252FX / E7252GX

Dimensional Outline of E7252GX

Unit mm

φ70
TERMINAL CONNECTIONS

9 8 7 6 5 1 2 3 4 E

NC NCNC NC
M A FOCAL SPOT

ET

191
TEMPERATURE RELAY
(NORMALLY CLOSED)
Note) Do not connect terminal No.1 and

71
No.5 or 6 in series circuit.

81

10°
CENTRAL OF FOCAL SPOT

53
A

B 18.28

A：±1.5mm，B：±1.5mm
φ140
CENTRAL RAY AND REFERENCE AXIS

90

ANODE
φ152.4

4-M6 8DEEP
146.5

11.1
12°

50.8
476

90
φ
92

45
134.5

4-M5 10DEEP

90 C
11.1

CATHODE

L
105

C : COMMON NC: NON-CONNECTION

L : LARGE FOCUS ET : EARTH TERMINAL
S : SMALL FOCUS ST : SHIELD TERMINAL (at cable cramp)
M : MAIN WINDING OF THE STATOR : CENTRAL X-RAY
A : AUX. WINDING OF THE STATOR ANODE & CATHODE TERMINAL
: IEC 60526 TYPE

- 21 -
E7252X / E7252FX / E7252GX

OVERSEAS SUBSIDIARIES AND AFFILIATES

EU REPRESENTATIVE
・TOSHIBA ELECTRONICS EUROPE
RIVERSIDE WAY, CAMBERLEY, SURREY. GU15 3YA U.K.
PHONE (0) 1276 694600 FAX (0) 1276 694800

For Sales & Technical Services, please contact the following representative:

・TOSHIBA ELECTRONICS EUROPE

RIVERSIDE WAY, CAMBERLEY, SURREY. GU15 3YA U.K.
PHONE (0) 1276 694600 FAX (0) 1276 694800

・TOSHIBA AMERICA ELECTRONIC COMPONENTS, INC.

2150 EAST LAKE COOK ROAD, SUITE 310
BUFFALO GROVE, ILLINOIS 60089 USA
PHONE (847) 945-1500 FAX (847) 945-1044

・TOSHIBA ELECTRON DEVICES &

MATERIALS TRADING (SHANGHAI) CO., LTD. (TEMS)
No.689, GUANG DONG RD, SHANGHAI, 200001,CHINA
RM607, HAITONG SECURITIES TOWER
PHONE (21) 6341-0055 FAX (21) 6341-0990

Sales & Marketing Department

1385 SHIMOISHIGAMI, OTAWARA-SHI, TOCHIGI-KEN, 324-8550, JAPAN
PHONE : +81-287-26-6666 FAX : +81-287-26-6060
http://www.toshiba-tetd.co.jp/

Toshiba Electron Tubes & Devices Co., Ltd. Toshiba Electron Tubes & Devices Co., Ltd. meets
meets the Environmental Management internationally recognized Standards for Quality
System Standard, ISO 14001 Management System ISO 9001, ISO 13485