Product Guide o e w20

Wärtsilä 20
PRODUCT GUIDE
© Copyright by WÄRTSILÄ FINLAND OY
COPYRIGHT © 2019 by WÄRTSILÄ FINLAND OY
All rights reserved. No part of this booklet may be reproduced or copied in any form or by any means (electronic,
mechanical, graphic, photocopying, recording, taping or other information retrieval systems) without the prior written
permission of the copyright owner.
THIS PUBLICATION IS DESIGNED TO PROVIDE AN ACCURATE AND AUTHORITATIVE INFORMATION WITH
REGARD TO THE SUBJECT-MATTER COVERED AS WAS AVAILABLE AT THE TIME OF PRINTING. HOWEVER,THE
PUBLICATION DEALS WITH COMPLICATED TECHNICAL MATTERS SUITED ONLY FOR SPECIALISTS IN THE
AREA, AND THE DESIGN OF THE SUBJECT-PRODUCTS IS SUBJECT TO REGULAR IMPROVEMENTS,
MODIFICATIONS AND CHANGES. CONSEQUENTLY, THE PUBLISHER AND COPYRIGHT OWNER OF THIS
PUBLICATION CAN NOT ACCEPT ANY RESPONSIBILITY OR LIABILITY FOR ANY EVENTUAL ERRORS OR
OMISSIONS IN THIS BOOKLET OR FOR DISCREPANCIES ARISING FROM THE FEATURES OF ANY ACTUAL ITEM
IN THE RESPECTIVE PRODUCT BEING DIFFERENT FROM THOSE SHOWN IN THIS PUBLICATION. THE PUBLISHER
AND COPYRIGHT OWNER SHALL UNDER NO CIRCUMSTANCES BE HELD LIABLE FOR ANY FINANCIAL
CONSEQUENTIAL DAMAGES OR OTHER LOSS, OR ANY OTHER DAMAGE OR INJURY, SUFFERED BY ANY
PARTY MAKING USE OF THIS PUBLICATION OR THE INFORMATION CONTAINED HEREIN.
Wärtsilä 20 Product Guide Introduction
Introduction
This Product Guide provides data and system proposals for the early design
phase of marine engine installations. For contracted projects specific
instructions for planning the installation are always delivered. Any data and
information herein is subject to revision without notice. This 1/2019 issue
replaces all previous issues of the Wärtsilä 20 Project Guides.
Issue Published Updates
1/2019 12.07.2019 Technical data section updated, UNIC C1 added in Chapter Automation.
Other minor updates throughout the product guide.
1/2018 7.11.2018 Technical data section updated (e.g. SCR, 1200 rpm and HFO Optimized
engines added). Other minor updates throughout the product guide.
1/2017 14.02.2017 Technical data section updated. Other minor updates throughout the product
guide.
1/2016 06.09.2016 Technical data section updated
1/2015 14.10.2015 Numerous updates throughout the product guide
1/2013 19.04.2013 Chapters Fuel Oil System and Lubrication Oil System updated with low sulphur
operation, several other updates throughout the product guide.
Wärtsilä, Marine Solutions
Vaasa, July 2019
DAAB605808 iii
This page intentionally left blank
Wärtsilä 20 Product Guide Table of contents
Table of contents
1. Main Data and Outputs ............................................................................................................................ 1-1
1.1 Technical main data ............................................................................................................................. 1-1
1.2 Maximum continuous output ............................................................................................................... 1-1
1.3 Reference conditions ........................................................................................................................... 1-3
1.4 Operation in inclined position (only for Marine Business engines) ...................................................... 1-3
1.5 Principal dimensions and weights ........................................................................................................ 1-4
2. Operating Ranges .................................................................................................................................... 2-1

2.1 Engine operating modes ...................................................................................................................... 2-1
2.2 Engine operating range ........................................................................................................................ 2-1
2.3 Loading capacity .................................................................................................................................. 2-8
2.4 Low load operation ............................................................................................................................... 2-13
2.5 Low air temperature ............................................................................................................................ 2-13
3. Technical Data .......................................................................................................................................... 3-1

3.1 Introduction .......................................................................................................................................... 3-1
3.2 Wärtsilä 4L20 ........................................................................................................................................ 3-1
3.3 Wärtsilä 6L20 ........................................................................................................................................ 3-8
3.4 Wärtsilä 8L20 ........................................................................................................................................ 3-20
3.5 Wärtsilä 9L20 ........................................................................................................................................ 3-32
4. Description of the Engine ........................................................................................................................ 4-1

4.1 Definitions ............................................................................................................................................. 4-1
4.2 Main components and systems ........................................................................................................... 4-1
4.3 Cross sections of the engine ................................................................................................................ 4-4
4.4 Expected Technical Life Time ............................................................................................................... 4-5
4.5 Engine storage ..................................................................................................................................... 4-7
5. Piping Design, Treatment and Installation ............................................................................................. 5-1

5.1 Pipe dimensions ................................................................................................................................... 5-1
5.2 Trace heating ........................................................................................................................................ 5-2
5.3 Pressure class ...................................................................................................................................... 5-2
5.4 Pipe class ............................................................................................................................................. 5-3
5.5 Insulation .............................................................................................................................................. 5-4
5.6 Local gauges ........................................................................................................................................ 5-4
5.7 Cleaning procedures ............................................................................................................................ 5-4
5.8 Flexible pipe connections ..................................................................................................................... 5-5
5.9 Clamping of pipes ................................................................................................................................ 5-7
6. Fuel Oil System ......................................................................................................................................... 6-1

6.1 Acceptable fuel characteristics ............................................................................................................ 6-1
6.2 Internal fuel oil system .......................................................................................................................... 6-14
6.3 External fuel oil system ........................................................................................................................ 6-17
7. Lubricating Oil System ............................................................................................................................ 7-1

7.1 Lubricating oil requirements ................................................................................................................. 7-1
7.2 Internal lubricating oil system ............................................................................................................... 7-2
7.3 External lubricating oil system ............................................................................................................. 7-6
7.4 Crankcase ventilation system ............................................................................................................. 7-12
7.5 Flushing instructions ............................................................................................................................ 7-14
8. Compressed Air System .......................................................................................................................... 8-1

8.1 Internal compressed air system ........................................................................................................... 8-1
DAAB605808 v
Table of contents Wärtsilä 20 Product Guide
8.2 External compressed air system .......................................................................................................... 8-4
9. Cooling Water System ............................................................................................................................. 9-1

9.1 Water quality ........................................................................................................................................ 9-1
9.2 Internal cooling water system .............................................................................................................. 9-2
9.3 External cooling water system ............................................................................................................. 9-7
10. Combustion Air System ......................................................................................................................... 10-1

10.1 Engine room ventilation ...................................................................................................................... 10-1
10.2 Combustion air system design ........................................................................................................... 10-3
11. Exhaust Gas System .............................................................................................................................. 11-1

11.1 Internal exhaust gas system ............................................................................................................... 11-1
11.2 Temperature sensor location after Turbocharger ............................................................................... 11-3
11.3 Exhaust gas outlet .............................................................................................................................. 11-4
11.4 External exhaust gas system ............................................................................................................. 11-6
12. Turbocharger Cleaning .......................................................................................................................... 12-1

12.1 Turbine cleaning system ..................................................................................................................... 12-1
12.2 Compressor cleaning system ............................................................................................................. 12-1
13. Exhaust Emissions ................................................................................................................................. 13-1

13.1 Diesel engine exhaust components ................................................................................................... 13-1
13.2 Marine exhaust emissions legislation ................................................................................................. 13-2
13.3 Methods to reduce exhaust emissions .............................................................................................. 13-2
14. Automation System ................................................................................................................................ 14-1

14.1 UNIC C1 ............................................................................................................................................. 14-1
14.2 UNIC C2 ............................................................................................................................................. 14-7
14.3 UNIC 2nd Generation ......................................................................................................................... 14-16
15. Foundation .............................................................................................................................................. 15-1

15.1 Steel structure design ........................................................................................................................ 15-1
15.2 Mounting of main engines .................................................................................................................. 15-1
15.3 Mounting of generating sets .............................................................................................................. 15-6
15.4 Flexible pipe connections ................................................................................................................... 15-8
16. Vibration and Noise ................................................................................................................................ 16-1

16.1 External forces & couples ................................................................................................................... 16-1
16.2 Mass moments of inertia .................................................................................................................... 16-5
16.3 Structure borne noise ......................................................................................................................... 16-5
16.4 Air borne noise ................................................................................................................................... 16-6
16.5 Exhaust noise ..................................................................................................................................... 16-7
17. Power Transmission ............................................................................................................................... 17-1

17.1 Flexible coupling ................................................................................................................................ 17-1
17.2 Clutch ................................................................................................................................................. 17-2
17.3 Shaft locking device ........................................................................................................................... 17-2
17.4 Power-take-off from the free end ....................................................................................................... 17-3
17.5 Input data for torsional vibration calculations .................................................................................... 17-4
17.6 Turning gear ........................................................................................................................................ 17-5
18. Engine Room Layout .............................................................................................................................. 18-1

18.1 Crankshaft distances .......................................................................................................................... 18-1
18.2 Space requirements for maintenance ................................................................................................ 18-3
18.3 Transportation and storage of spare parts and tools ......................................................................... 18-3
18.4 Required deck area for service work .................................................................................................. 18-4
vi DAAB605808
Wärtsilä 20 Product Guide Table of contents
19. Transport Dimensions and Weights ..................................................................................................... 19-1

19.1 Lifting of engines ................................................................................................................................ 19-1
19.2 Engine components ........................................................................................................................... 19-3
20. Product Guide Attachments .................................................................................................................. 20-1
21. ANNEX ..................................................................................................................................................... 21-1

21.1 Unit conversion tables ........................................................................................................................ 21-1
21.2 Collection of drawing symbols used in drawings ............................................................................... 21-2
DAAB605808 vii
Wärtsilä 20 Product Guide 1. Main Data and Outputs
1. Main Data and Outputs
1.1 Technical main data

The Wärtsilä 20 is a 4-stroke, non-reversible, turbocharged and intercooled diesel engine with
direct injection of fuel.
Cylinder bore ........................................ 200 mm
Stroke .................................................... 280 mm
Piston displacement ............................. 8.8 l/cyl
Number of valves .................................. 2 inlet valves and 2 exhaust valves
Cylinder configuration ........................... 4, 6, 8, 9, in-line
Direction of rotation .............................. Clockwise, counterclockwise on request
Speed .................................................... 900, 1000, 1200 rpm
Mean piston speed ............................... 8.4, 9.3, 11,2 m/s
1.2 Maximum continuous output

1.2.1 Rated output
The engine is available in 1200 and 1000 rpm versions for propeller propulsion and for electric
propulsion 1200, 1000 and 900 rpm.
1.2.1.1 Diesel electric propulsion, constant speed
Table 1-1 Output tables (kW)
Engine 1200 rpm 1000 rpm 900 rpm
4L20 - 800 740
6L20 1320 1200 1110
8L20 1760 1600 1480
9L20 1980 1800 1665
Outputs are given in kW at flywheel, including or excluding engine driven pumps, ISO 15550
- 2002 (E) conditions.
1.2.1.2 Mechanical controllable pitch propeller propulsion, variable

speed
Engine 1200 rpm 1000 rpm
4L20 - 800
6L20 1320 1200
DAAB605808 1-1
1. Main Data and Outputs Wärtsilä 20 Product Guide
Engine 1200 rpm 1000 rpm
8L20 1760 1600
9L20 1980 1600
1.2.2 Rated Output - Auxiliary Engines

Engine 1200 rpm 1000 rpm 900 rpm
4L20 - 800 740
6L20 1320 1200 1110
8L20 1760 1600 1480
9L20 1980 1800 1665
The mean effective pressure pe can be calculated as follows:
where:
Pe = Mean effective pressure [bar]
P = Output per cylinder [kW]
n = Engine speed [r/min]
D = Cylinder diameter [mm]
L = Length of piston stroke [mm]
c = Operating cycle (4)
1-2 DAAB605808
1.3 Reference conditions

The output is available up to an air temperature of max. 45°C. For higher temperatures, the
output has to be reduced according to the formula stated in ISO 3046-1:2002 (E).
The specific fuel oil consumption is stated in the chapter Technical data. The stated specific
fuel oil consumption applies to engines with engine driven pumps, operating in ambient
conditions according to ISO 15550:2002 (E). The ISO standard reference conditions are:
total barometric pressure 100 kPa
air temperature 25 °C
relative humidity 30 %
charge air coolant temperature 25 °C
Correction factors for the fuel oil consumption in other ambient conditions are given in standard
ISO 15550:2002 (E).
1.4 Operation in inclined position (only for Marine Business

engines)
The engine is designed to ensure proper engine operation at inclination positions, specified
under IACS M46.2 (1982) (Rev.1 June 2002) - Main and auxiliary machinery.
Max. inclination angles at which the engine will operate satisfactorily:
● Permanent athwart ship inclinations (list) 15°
● Temporary athwart ship inclinations (roll) 22.5°
● Permanent fore-and-aft inclinations (trim) 5°
● Temporary fore and aft inclinations (pitch) 7.5°
Inclination in all directions requires special arrangements.
NOTE
- Athwartships and fore-end-aft inclinations may occur simultaneously
- Inclination angles are applicable ONLY to marine main and auxiliary machinery
engines. Emergency power installations are not currently available
- If inclination exceeds some of the above mentioned IACS requirements, a special
arrangement might be needed. Please fill in a NSR (Non-standard request)
DAAB605808 1-3
1.5 Principal dimensions and weights
Fig 1-1 Main Engines (DAAE060842C) - UNIC C1, UNIC C2 & UNIC 2.0
A TOTAL LENGTH OF THE ENGINE
B HEIGHT FROM THE CRANKSHAFT CENTERLINE TO THE EXHAUST GAS OUTLET
C TOTAL WIDTH OF THE ENGINE
D MINIMUM HEIGHT WHEN REMOVING A PISTON
E HEIGHT FROM THE CRANKSHAFT CENTERLINE TO THE ENGINE FEET
F DIMENSION FROM THE CRANKSHAFT CENTERLINE TO THE BOTTOM OF THE OIL SUMP
G LENGTH OF THE ENGINE BLOCK
H DIMENSION FROM THE END OF THE ENGINE BLOCK TO MOUNTING FACE FOR FLYWHEEL
ON THE CRANKSHAFT
I WIDTH OF THE OIL SUMP
J FROM THE ENGINE BLOCK TO THE OUTERMOST FREE END
K WIDTH OF THE ENGINE AT THE ENGINE FEET, FIXED MOUNTING
K1 WIDTH OF THE ENGINE AT THE ENGINE FEET, FLEXIBLE MOUNTING
L CAMSHAFT OVERHAUL DISTANCE
M DIMENSION FROM THE CENTER OF THE CRANKSHAFT TO THE OUTERMOST PART ON THE
BACK SIDE OF THE ENGINE
N FROM THE ENGINE BLOCK TO THE OUTERMOST PART AT THE FLYWHEEL END
O CHARGE AIR COOLER OVERHAUL DISTANCE
P TOTAL HEIGHT OF THE ENGINE
Q HEIGHT FOR THE DOOR ON THE CONNECTING BOX, FROM CRANKSHAFT CENTERLINE
1-4 DAAB605808
Fig 1-2 Engine Weight (V92E0066F) - UNIC C1, UNIC C2 & UNIC 2.0
DAAB605808 1-5
Fig 1-3 Generating sets (V58E0576D)
Engine A* B C* D* E* F* G* H* I K* L* M Weight
*
W 4L20 4910 665 4050 2460 725 990 1270/1420 1770/1920 1800 1580/1730 2338 1168 14.0
W 6L20 5325 663 4575 2300 725 895/975/1025 1270/1420/1570 1770/1920/2070 1800 1580/1730/1880 2243/2323/2373 1299 16.8
W 8L20 6030 731 5100 2310 725 1025/1075 1420/1570 1920/2070 1800 1730/1880 2474/2524 1390 20.7
W 9L20 6535 731 5400 2580 725 1075/1125 1570/1800 2070/2300 1800 1880/2110 2524/2574 1390 23.8
* Dependent on generator type and size.

Dimensions in mm. Weight in tons.
NOTE
Generating set dimensions (V58E0576D) shown above are for reference ONLY.
1-6 DAAB605808
Wärtsilä 20 Product Guide 2. Operating Ranges
2. Operating Ranges
2.1 Engine operating modes

If the engine is configured for Selective Catalytic Reduction (SCR) use then it can be operated
in two modes; IMO Tier 2 mode and SCR mode. The mode can be selected by an input signal
to the engine automation system.
In SCR mode the exhaust gas temperatures after the turbocharger are actively monitored and
adjusted to stay within the operating temperature window of the SCR.
2.2 Engine operating range

Running below nominal speed the load must be limited according to the diagrams in this
chapter in order to maintain engine operating parameters within acceptable limits. Operation
in the shaded area is permitted only temporarily during transients. Minimum speed is indicated
in the diagram, but project specific limitations may apply.
2.2.1 Controllable pitch propellers

An automatic load control system is required to protect the engine from overload. The load
control reduces the propeller pitch automatically, when a pre-programmed load versus speed
curve (“engine limit curve”) is exceeded, overriding the combinator curve if necessary. The
engine load is derived from fuel rack position and actual engine speed (not speed demand).
The propeller efficiency is highest at design pitch. It is common practice to dimension the
propeller so that the specified ship speed is attained with design pitch, nominal engine speed
and 85% output in the specified loading condition. The power demand from a possible shaft
generator or PTO must be taken into account. The 15% margin is a provision for weather
conditions and fouling of hull and propeller. An additional engine margin can be applied for
most economical operation of the engine, or to have reserve power.
The propulsion control must also include automatic limitation of the load increase rate.
Maximum loading rates can be found later in this chapter.
DAAB605808 2-1
2. Operating Ranges Wärtsilä 20 Product Guide
Fig 2-1 Operating field - CP Propeller 1000 rpm (DAAF007339B)
2-2 DAAB605808
Fig 2-2 Operating field - CP Propeller 1000 rpm SCR with sulphur content 0,5% < S
≤ 3,5% (DAAF360481C)
DAAB605808 2-3
Fig 2-3 Operating field - CP Propeller 1200 rpm (DAAF437248)
2-4 DAAB605808
Fig 2-4 Operating field - CP Propeller 1200 rpm SCR with sulphur content S ≤ 0,5%
and 0,5% < S ≤ 3,5% (DAAF424192A)
NOTE
MCR = Maximum Continuous Rating
CSR = Continuous Service Rating
Allowed for W20 with SCR at 45 °C suction air temperature.
2.2.2 Fixed pitch propellers

The thrust and power absorption of a given fixed pitch propeller is determined by the relation
between ship speed and propeller revolution speed. The power absorption during acceleration,
manoeuvring or towing is considerably higher than during free sailing for the same revolution
speed. Increased ship resistance, for reason or another, reduces the ship speed, which
increases the power absorption of the propeller over the whole operating range.
Loading conditions, weather conditions, ice conditions, fouling of hull, shallow water, and
manoeuvring requirements must be carefully considered, when matching a fixed pitch propeller
to the engine. The nominal propeller curve shown in the diagram must not be exceeded in
DAAB605808 2-5
service, except temporarily during acceleration and manoeuvring. A fixed pitch propeller for
a free sailing ship is therefore dimensioned so that it absorbs max. 85% of the engine output
at nominal engine speed during trial with loaded ship. Typically this corresponds to about
82% for the propeller itself.
If the vessel is intended for towing, the propeller is dimensioned to absorb 95% of the engine
power at nominal engine speed in bollard pull or towing condition. It is allowed to increase
the engine speed to 101.7% in order to reach 100% MCR during bollard pull.
A shaft brake should be used to enable faster reversing and shorter stopping distance (crash
stop). The ship speed at which the propeller can be engaged in reverse direction is still limited
by the windmilling torque of the propeller and the torque capability of the engine at low
revolution speed.
Fig 2-5 Operating field - FP Propeller 1000 rpm (DAAF007340B)
2-6 DAAB605808
Fig 2-6 Operating field - FP Propeller 1200 rpm (DAAF437249)
MCR = Maximum Continuous Rating

CSR = Continuous Service Rating
2.2.2.1 FP propellers in twin screw vessels

Requirements regarding manoeuvring response and acceleration, as well as overload with
one engine out of operation must be very carefully evaluated if the vessel is designed for free
sailing, in particular if open propellers are applied. If the bollard pull curve significantly exceeds
the maximum overload limit, acceleration and manoeuvring response can be very slow. Nozzle
propellers are less problematic in this respect.
2.2.3 Dredgers
Mechanically driven dredging pumps typically require a capability to operate with full torque
down to 80% of nominal engine speed. This requirement results in significant de-rating of the
engine.
DAAB605808 2-7
2.3 Loading capacity

Controlled load increase is essential for highly supercharged diesel engines, because the
turbocharger needs time to accelerate before it can deliver the required amount of air. A slower
loading ramp than the maximum capability of the engine permits a more even temperature
distribution in engine components during transients.
The engine can be loaded immediately after start, provided that the engine is pre-heated to
a HT-water temperature of 60…70ºC, and the lubricating oil temperature of 30...40 ºC.
The ramp for normal loading applies to engines that have reached normal operating
temperature.
2-8 DAAB605808
2.3.1 Mechanical propulsion
Fig 2-7 Maximum recommended load increase rates for variable speed engines
The propulsion control must include automatic limitation of the load increase rate. If the control
system has only one load increase ramp, then the ramp for a preheated engine should be
used. In tug applications the engines have usually reached normal operating temperature
before the tug starts assisting. The “emergency” curve is close to the maximum capability of
the engine.
If minimum smoke during load increase is a major priority, slower loading rate than in the
diagram can be necessary below 50% load.
Large load reductions from high load should also be performed gradually. In normal operation
the load should not be reduced from 100% to 0% in less than 15 seconds. When absolutely
necessary, the load can be reduced as fast as the pitch setting system can react (overspeed
due to windmilling must be considered for high speed ships).
DAAB605808 2-9
2.3.2 Diesel electric propulsion and auxiliary engines
Fig 2-8 Maximum recommended load increase rates for engines operating at nominal
speed
In diesel electric installations loading ramps are implemented both in the propulsion control
and in the power management system, or in the engine speed control in case isochronous
load sharing is applied. If a ramp without knee-point is used, it should not achieve 100% load
in shorter time than the ramp in the figure. When the load sharing is based on speed droop,
the load increase rate of a recently connected generator is the sum of the load transfer
performed by the power management system and the load increase performed by the
propulsion control.
The “emergency” curve is close to the maximum capability of the engine and it shall not be
used as the normal limit. In dynamic positioning applications loading ramps corresponding to
20-30 seconds from zero to full load are however normal. If the vessel has also other operating
modes, a slower loading ramp is recommended for these operating modes.
In typical auxiliary engine applications there is usually no single consumer being decisive for
the loading rate. It is recommended to group electrical equipment so that the load is increased
in small increments, and the resulting loading rate roughly corresponds to the “normal” curve.
In normal operation the load should not be reduced from 100% to 0% in less than 15 seconds.
If the application requires frequent unloading at a significantly faster rate, special arrangements
can be necessary on the engine. In an emergency situation the full load can be thrown off
instantly.
2.3.2.1 Maximum instant load steps

The electrical system must be designed so that tripping of breakers can be safely handled.
This requires that the engines are protected from load steps exceeding their maximum load
acceptance capability. The maximum permissable load step is 33% MCR for an engine without
SCR and 25% MCR if the engine is equipped wit an SCR. The resulting speed drop is less
than 10% and the recovery time to within 1% of the steady state speed at the new load level
is max. 5 seconds.
When electrical power is restored after a black-out, consumers are reconnected in groups or
in a fast sequence with few generators on the busbar, which may cause significant load steps.
2-10 DAAB605808
The engine must be allowed to recover for at least 7 seconds before applying the following
load step, if the load is applied in maximum steps.
Maximum load steps, DME and AUX engines

ENGINES WITHOUT SCR (Tier2)
Instant Load Application Engine unloading
● Maximum load step according to figure below ● Instant load rejection 100 % - 0 %
(0 – 33 – 66 – 100 %)
● Maximum transient speed increase of 10 % of
● Maximum transient speed decrease of 10 % of the rated speed
rated speed
● Steady-state frequency band ± 1.0 %
● Steady-state recovery time ≤ 5 sec.
● Time between load steps ≥ 5 sec., however the
max. load limit specified in the graph below
should not be exceeded
Fig 2-9
DAAB605808 2-11
ENGINES EQUIPPED WITH SCR (fuel sulphur content ≥ 0.1%)
Instant Load Application Engine unloading
● Maximum load step according to figure below ● Instant load rejection 100 % - 0 %
(0 – 25 – 50 – 75 – 100 %)
● Maximum transient speed increase of 10 % of
● Maximum transient speed decrease of 10 % of rated speed
rated speed
● Time between load steps ≥ 5 sec., however the
max. load limit specified in the graph below
should not be exceeded
2-12 DAAB605808
2.3.2.2 Start-up time

A diesel generator typically reaches nominal speed in about 20...25 seconds after the start
signal. The acceleration is limited by the speed control to minimise smoke during start-up.
2.4 Low load operation
Operation below 44 kW/cyl 1) load on HFO or below 22 kW/cyl 2) load on MDF

● Maximum 100 hours continuous operation. At intervals of 100 operating hours the engine
must be loaded to minimum 70 % of the rated output for one hours before continuing with
low-load operation or shutting down
Operation at or above 44 kW/cyl 1) load on HFO or at or above 22 kW/cyl 2) load on MDF

● No restrictions
1) 20 % from 220 kW/cyl

2) 10 % from 220 kW/cyl
NOTE
Operating restrictions on SCR applications in low load operation to be observed.
Please refer to Performance Manual for details.
2.5 Low air temperature

Depending on the setup down to -45ºC.
For further guidelines, see chapter Combustion air system design.
DAAB605808 2-13
Wärtsilä 20 Product Guide 3. Technical Data
3. Technical Data
3.1 Introduction
This chapter contains technical data of the engine (heat balance, flows, pressures etc.) for
design of auxiliary systems. Further design criteria for external equipment and system layouts
are presented in the respective chapter.
3.1.1 Engine driven pumps

The fuel consumption stated in the technical data tables is with engine driven pumps. The fuel
consumption of engine driven pump is given below, correction in g/kWh.
Table 3-1 Constant speed engines
Engine driven pump Engine load [%] - 900 or 1000 / 1200 rpm
100 85 75 50
Lube Oil 2.4 / 2.8 / 3.1 / 4.9 /

2.2 2.5 2.9 4.5
LT Water 0.6 / 0.7 / 0.8 / 1.1 /

0.5 0.6 0.7 1.0
HT Water 0.5 / 0.6 / 0.7 / 1.0 /

0.5 0.6 0.6 1.0
Fuel feed pump 0.1 / 0.1 / 0.1 / 0.2 /

0.1 0.1 0.1 0.1
Table 3-2 Variable speed engines
Engine driven pump Engine load [%] - 1000 / 1200 rpm
100 85 75 50
Lube Oil 3.4 / 3.6 / 4.0 / 5.2 /

3.1 3.3 3.7 5.0
LT Water 0.6 / 0.6 / 0.6 / 0.6 /

0.6 0.5 0.5 0.5
HT Water 0.5 / 0.5 / 0.5 / 0.5 /

0.5 0.5 0.5 0.5
Fuel feed pump 0.1 / 0.1 / 0.1 / 0.1 /

0.1 0.1 0.1 0.1
3.2 Wärtsilä 4L20

3.2.1 IMO Tier 2
Wärtsilä 4L20 AE/DE AE/DE ME ME
Cylinder output kW 185 200 200 200
Engine speed RPM 900 1000 1000 1000
Speed mode Constant Constant Variable Constant
Engine output kW 740 800 800 800
Mean effective pressure MPa 2.8 2.73 2.73 2.73
Combustion air system (Note 1)
Flow at 100% load kg/s 1.4 1.51 1.51 1.51
DAAB605808 3-1
3. Technical Data Wärtsilä 20 Product Guide
Temperature at turbocharger intake, max. °C 45 45 45 45
Temperature after air cooler (TE601) °C 50...70 50...70 50...70 50...70
Exhaust gas system (Note 2)
Flow at 100% load kg/s 1.44 1.56 1.56 1.56
Flow at 85% load kg/s 1.32 1.44 1.4 1.44
Flow at 75% load kg/s 1.16 1.28 1.2 1.28
Flow at 50% load kg/s 0.84 0.92 0.8 0.92
Temperature after turbocharger, 100% load °C 363 356 363 356

(TE517)

(TE517)

(TE517)

(TE517)
Backpressure, max. kPa 5.0 5.0 5.0 5.0
Calculated pipe diameter for 35 m/s mm 306 317 319 317
Heat balance (Note 3)
Jacket water, HT-circuit kW 160 168 168 168
Charge air, LT-circuit kW 248 272 272 272
Lubricating oil, LT-circuit kW 116 124 124 124
Radiation kW 32 32 32 32
Fuel system (Note 4)
Pressure before injection pumps (PT101) kPa 700±50 700±50 700±50 700±50
Pressure before engine driven fuel feed pump, kPa 15 15 15 15

min. (MDF only)
Engine driven pump capacity (MDF only) m3/h 0.78 0.87 0.87 0.87
Fuel flow to engine (without engine driven m3/h 0.81 0.88 0.89 0.89
pump), approx.
HFO viscosity before engine cSt 16... 24 16... 24 16... 24 16... 24
Max. HFO temperature before engine (TE101) °C 140 140 140 140
MDF viscosity, min. cSt 1.8 1.8 1.8 1.8
Max. MDF temperature before engine (TE101) °C 45 45 45 45
Fuel consumption at 100% load, HFO g/kWh 198.2 200.1 201.0 200.6
Fuel consumption at 100% load, MDF g/kWh 197.2 199.1 200.1 199.6
3-2 DAAB605808
Clean leak fuel quantity, MDF at 100% load kg/h 2.16 2.16 2.16 2.16
Lubricating oil system
Pressure before bearings, nom. (PT201) kPa 450 450 450 450
Suction ability main pump, including pipe loss, kPa 20 20 20 20

max.
Priming pressure, nom. (PT201) kPa 80 80 80 80
Suction ability priming pump, including pipe kPa 20 20 20 20

loss, max.
Temperature before bearings, nom. (TE201) °C 66 66 66 66
Temperature after engine, approx. °C 78 78 78 78
Pump capacity (main), engine driven m³/h 24 27 34 27
Priming pump capacity, 50Hz/60Hz m³/h 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5
Oil volume, wet sump m³ 0.27 0.27 0.27 0.27
Oil volume in separate system oil tank m³ 1.0 1.1 1.1 1.1
Filter fineness, nom. mi- 25 25 25 25

crons
Oil consumption at 100% load, max. g/kWh 0.5 0.5 0.5 0.5
Crankcase ventilation flow rate at 100% load l/min 520 520 520 520
Crankcase ventilation backpressure, max. kPa 0.3 0.3 0.3 0.3
Oil volume in speed governor liters 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2
Cooling water system
High temperature cooling water system
Pressure at engine, after pump, nom. (PT401) kPa 200 + stat- 200 + stat- 200 + stat- 200 + stat-
ic ic ic ic
Pressure at engine, after pump, max. (PT401) kPa 500 500 350 500
Temperature before cylinder, approx. (TE401) °C 83 83 83 83
Temperature after engine, nom. °C 91 91 91 91
Capacity of engine driven pump, nom. m³/h 20 20 20 20
Pressure drop over engine, total kPa 90 90 90 90
Pressure drop in external system, max. kPa 120 120 120 120
Water volume in engine m³ 0.09 0.09 0.09 0.09
Pressure from expansion tank kPa 70...150 70...150 70...150 70...150
Low temperature cooling water system
ic ic ic ic
Temperature before engine, min...max °C 25...38 25...38 25...38 25...38
Pressure drop over charge air cooler kPa 30 30 30 30
Pressure drop over oil cooler kPa 30 30 30 30
DAAB605808 3-3
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000
Low pressure limit in air vessels kPa 1800 1800 1800 1800
Starting air consumption, start (successful) Nm3 1.2 1.2 1.2 1.2
Notes:
Note 1 At ISO 15550 conditions (ambient air temperature 25°C, LT-water 25°C) and 100% load. Flow tolerance 5%.
Note 2 At ISO 15550 conditions (ambient air temperature 25°C, LT-water 25°C). Flow tolerance 5% and temperature tolerance
15°C.
Also it's possible to have higher than "max" backpressure shown above, please contact Wärtsilä for additional information.
Note 3 At ISO 15550 conditions (ambient air temperature 25°C, LT-water 25°C) and 100% load. Tolerance for cooling water heat
10%, tolerance for radiation heat 30%. Fouling factors and a margin to be taken into account when dimensioning heat
exchangers.
Note 4 At ambient conditions according to ISO 15550. Lower calorific value 42 700 kJ/kg. With engine driven pumps (two cooling
water + one lubricating oil pump). Tolerance 5%.
ME = Engine driving propeller, variable speed

AE = Auxiliary engine driving generator
DE = Diesel-Electric engine driving generator
Subject to revision without notice.
3-4 DAAB605808
3.2.2 SCR Ready

Engine output kW 740 800 800 800
Flow at 100% load kg/s 1.4 1.51 1.51 1.51
Temperature at turbocharger intake, max. °C 45 45 45 45
Flow at 100% load kg/s 1.44 1.56 1.56 1.56
Flow at 85% load kg/s 1.24 1.4 1.36 1.4
Flow at 75% load kg/s 1.08 1.24 1.2 1.24
Flow at 50% load kg/s 0.8 0.8 0.8 0.8

(TE517)

(TE517)

(TE517)

(TE517)
Pressure before injection pumps (PT101) kPa 700±50 700±50 700±50 700±50
Pressure before engine driven fuel feed pump, kPa 15 15 15 15

min (MDF only)
Engine driven pump capacity (MDF only) m3/h 0.78 0.87 0.87 0.87
Fuel flow to engine (without engine driven m3/h 0.81 0.89 0.89 0.89
pump), approx.
Max. HFO temperature before engine (TE101) °C 140 140 140 140
Max. MDF temperature before engine (TE101) °C 45 45 45 45
DAAB605808 3-5
Clean leak fuel quantity, MDF at 100% load kg/h 2.16 2.16 2.16 2.16
Pressure before bearings, nom. (PT201) kPa 450 450 450 450
Suction ability main pump, including pipe loss, kPa 20 20 20 20

max.
Suction ability priming pump, including pipe kPa 20 20 20 20

loss, max.
Temperature before bearings, nom. (TE201) °C 66 66 66 66

crons
Crankcase ventilation flow rate at 100% load l/min 520 520 520 520
Crankcase ventilation backpressure, max. kPa 0.3 0.3 0.3 0.3
High temperature cooling water system
ic ic ic ic
Temperature before cylinder, approx. (TE401) °C 83 83 83 83
Low temperature cooling water system
3-6 DAAB605808
ic ic ic ic
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000
Starting air consumption, start (successful) Nm3 1.2 1.2 1.2 1.2
Notes:
15°C.
exchangers.

DAAB605808 3-7
3.3 Wärtsilä 6L20

3.3.1 IMO Tier 2
Wärtsilä 6L20 AE/DE AE/DE AE/DE AE/DE ME ME ME ME ME ME
LFO Op- HFO Op- LFO Op- HFO Op- LFO Op- HFO Op-
timized timized timized timized timized timized
Cylinder output kW 185 200 220 220 200 220 220 200 220 220
Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200
Speed mode Constant Constant Constant Constant Variable Variable Variable Constant Constant Constant
Engine output kW 1110 1200 1320 1320 1200 1320 1320 1200 1320 1320
Mean effective pressure MPa 2.8 2.73 2.5 2.5 2.73 2.5 2.5 2.73 2.5 2.5
Flow at 100% load kg/s 2.1 2.27 2.69 2.69 2.27 2.8 2.8 2.27 2.68 2.68
Temperature at turbocharger intake, °C 45 45 45 45 45 45 45 45 45 45

max.
Temperature after air cooler (TE601) °C 50...70 50...70 50...70 50...70 50...70 50...70 50...70 50...70 50...70 50...70
Flow at 100% load kg/s 2.16 2.34 2.76 2.76 2.34 2.88 2.88 2.34 2.76 2.76
Flow at 85% load kg/s 1.98 2.16 2.4 2.4 2.1 2.4 2.4 2.16 2.4 2.4
Flow at 75% load kg/s 1.74 1.92 2.16 2.16 1.8 2.04 2.04 1.92 2.16 2.16
Flow at 50% load kg/s 1.26 1.38 1.5 1.5 1.2 1.38 1.38 1.38 1.5 1.5
Temperature after turbocharger, 100% °C 363 356 316 316 363 319 319 356 316 316
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Backpressure, max. kPa 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0
Calculated pipe diameter for 35 m/s mm 375 388 408 408 391 418 418 388 408 408
Jacket water, HT-circuit kW 240 252 294 294 252 294 294 252 294 294
Charge air, LT-circuit kW 372 408 468 468 408 528 528 408 468 468
Lubricating oil, LT-circuit kW 174 186 156 156 186 162 162 186 156 156
Radiation kW 48 48 47 47 48 47 47 48 47 47
Pressure before injection pumps kPa 700±50 700±50 700±50 700±50 700±50 700±50 700±50 700±50 700±50 700±50
(PT101)
Pressure before engine driven fuel feed kPa 15 15 15 15 15 15 15 15 15 15

pump, min. (MDF only)
Engine driven pump capacity (MDF m3/h 1.34 1.49 1.5 n/a 1.49 1.5 n/a 1.49 1.5 n/a
only)
Fuel flow to engine (without engine m3/h 1.19 1.3 n/a 1.44 1.3 n/a 1.47 1.3 n/a 1.47
driven pump), approx.
HFO viscosity before engine cSt 16... 24 16... 24 0... 0 16... 24 16... 24 0... 0 16... 24 16... 24 0... 0 16... 24
3-8 DAAB605808

Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200
Max. HFO temperature before engine °C 140 140 0 140 140 0 140 140 0 140
(TE101)
MDF viscosity, min. cSt 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8
Max. MDF temperature before engine °C 45 45 45 45 45 45 45 45 45 45

(TE101)
Fuel consumption at 100% load, HFO g/kWh 193.4 195.8 n/a 197.7 196.3 n/a 201.6 196.3 n/a 201.6
Fuel consumption at 100% load, MDF g/kWh 192.5 194.9 195.7 197.6 195.3 199.6 202.4 195.3 199.6 201.5
Clean leak fuel quantity, MDF at 100% kg/h 3.24 3.24 3.24 3.24 3.24 3.24 3.24 3.24 3.24 3.24
load
Pressure before bearings, nom. kPa 450 450 450 450 450 450 450 450 450 450
(PT201)
Suction ability main pump, including kPa 20 20 20 20 20 20 20 20 20 20

pipe loss, max.
Priming pressure, nom. (PT201) kPa 80 80 80 80 80 80 80 80 80 80
Suction ability priming pump, including kPa 20 20 20 20 20 20 20 20 20 20

pipe loss, max.
Temperature before bearings, nom. °C 66 66 66 66 66 66 66 66 66 66

(TE201)
Temperature after engine, approx. °C 78 78 78 78 78 78 78 78 78 78
Pump capacity (main), engine driven m³/h 31 34 34 34 48 48 48 34 34 34
Priming pump capacity, 50Hz/60Hz m³/h 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5
Oil volume, wet sump m³ 0.38 0.38 0.38 0.38 0.5 0.5 0.5 0.5 0.5 0.5
Oil volume in separate system oil tank m³ 1.5 1.6 1.8 1.8 1.6 1.8 1.8 1.6 1.8 1.8
Filter fineness, nom. mi- 25 25 25 25 25 25 25 25 25 25

crons
Oil consumption at 100% load, max. g/kWh 0.5 0.5 0.35 0.35 0.5 0.35 0.35 0.5 0.35 0.35
Crankcase ventilation flow rate at l/min 780 780 780 780 780 780 780 780 780 780
100% load
Crankcase ventilation backpressure, kPa 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
max.
Oil volume in speed governor liters 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2
High temperature cooling water

system
Pressure at engine, after pump, nom. kPa 200 + 200 + 200 + 200 + 200 + 200 + 200 + 200 + 200 + 200 +
(PT401) static static static static static static static static static static
Pressure at engine, after pump, max. kPa 500 500 500 500 350 350 350 500 500 500
(PT401)
DAAB605808 3-9

Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200
Temperature before cylinder, approx. °C 83 83 83 83 83 83 83 83 83 83

(TE401)
Temperature after engine, nom. °C 91 91 91 91 91 91 91 91 91 91
Capacity of engine driven pump, nom. m³/h 29 30 30 30 30 30 30 30 30 30
Pressure drop over engine, total kPa 90 90 90 90 90 90 90 90 90 90
Pressure drop in external system, max. kPa 120 120 120 120 120 120 120 120 120 120
Water volume in engine m³ 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12 0.12
Pressure from expansion tank kPa 70...150 70...150 70...150 70...150 70...150 70...150 70...150 70...150 70...150 70...150
Low temperature cooling water sys-

tem
(PT451)
Temperature before engine, min...max °C 25...38 25...38 25...38 25...38 25...38 25...38 25...38 25...38 25...38 25...38
Pressure drop over charge air cooler kPa 30 30 30 30 30 30 30 30 30 30
Pressure drop over oil cooler kPa 30 30 30 30 30 30 30 30 30 30
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Low pressure limit in air vessels kPa 1800 1800 1800 1800 1800 1800 1800 1800 1800 1800
Starting air consumption, start (suc- Nm3 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2
cessful)
Notes:
15°C.
exchangers.

3-10 DAAB605808
3.3.2 SCR Ready

3.3.2.1 900 & 1000 rpm
Engine output kW 1110 1200 1200 1200
Flow at 100% load kg/s 2.1 2.27 2.27 2.27
Temperature at turbocharger intake, °C 45 45 45 45

max.
Flow at 100% load kg/s 2.16 2.34 2.34 2.34
Flow at 85% load kg/s 1.86 2.1 2.04 2.1
Flow at 75% load kg/s 1.62 1.86 1.8 1.86
Flow at 50% load kg/s 1.2 1.2 1.2 1.2
Temperature after turbocharger, 100% °C 363 358 363 358

load (TE517)

load (TE517)

load (TE517)

load (TE517)
Pressure before injection pumps kPa 700±50 700±50 700±50 700±50

(PT101)
Pressure before engine driven fuel feed kPa 15 15 15 15

Engine driven pump capacity (MDF m3/h 1.34 1.49 1.49 1.49
only)
Fuel flow to engine (without engine m3/h 1.2 1.3 1.3 1.3
Max. HFO temperature before engine °C 140 140 140 140

(TE101)
DAAB605808 3-11
Max. MDF temperature before engine °C 45 45 45 45

(TE101)
Clean leak fuel quantity, MDF at 100% kg/h 3.24 3.24 3.24 3.24
load
Pressure before bearings, nom. kPa 450 450 450 450

(PT201)
Suction ability main pump, including kPa 20 20 20 20

pipe loss, max.
Suction ability priming pump, including kPa 20 20 20 20

pipe loss, max.
Temperature before bearings, nom. °C 66 66 66 66

(TE201)

crons
Crankcase ventilation flow rate at l/min 780 780 780 780

100% load
Crankcase ventilation backpressure, kPa 0.3 0.3 0.3 0.3

max.

system
Pressure at engine, after pump, nom. kPa 200 + 200 + 200 + 200 +
(PT401) static static static static
Pressure at engine, after pump, max. kPa 500 500 350 500
(PT401)
Temperature before cylinder, approx. °C 83 83 83 83

(TE401)
3-12 DAAB605808

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000
Starting air consumption, start (suc- Nm3 1.2 1.2 1.2 1.2
cessful)
Notes:
15°C.
exchangers.

DAAB605808 3-13
3.3.2.2 1200 rpm fuel sulphur content ≤ 0,5%

Wärtsilä 6L20 AE/DE ME ME AE/DE ME ME
LFO Op- LFO Op- LFO Op- HFO Op- HFO Op- HFO Op-
Cylinder output kW 220 220 220 220 220 220
Engine speed RPM 1200 1200 1200 1200 1200 1200
Speed mode Constant Variable Constant Constant Variable Constant
Engine output kW 1320 1320 1320 1320 1320 1320
Mean effective pressure MPa 2.5 2.5 2.5 2.5 2.5 2.5
Flow at 100% load kg/s 2.69 2.8 2.68 2.69 2.8 2.68
Temperature at turbocharger intake, °C 45 45 45 45 45 45

max.
Temperature after air cooler (TE601) °C 50...70 50...70 50...70 50...70 50...70 50...70
Flow at 100% load kg/s 2.76 2.88 2.76 2.76 2.88 2.76
Flow at 85% load kg/s 2.34 2.34 2.34 2.34 2.34 2.34
Flow at 75% load kg/s 2.1 2.04 2.1 2.1 2.04 2.1
Flow at 50% load kg/s 1.5 1.38 1.5 1.5 1.38 1.5
Temperature after turbocharger, 100% °C 320 320 320 320 320 320
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Backpressure, max. kPa 5.0 5.0 5.0 5.0 5.0 5.0
Calculated pipe diameter for 35 m/s mm 410 418 410 410 418 410
Jacket water, HT-circuit kW 300 294 300 300 294 300
Charge air, LT-circuit kW 468 528 468 468 528 468
Lubricating oil, LT-circuit kW 156 162 156 156 162 156
Radiation kW 47 47 47 47 47 47
Pressure before injection pumps kPa 700±50 700±50 700±50 700±50 700±50 700±50
(PT101)
Pressure before engine driven fuel feed kPa 15 15 15 15 15 15

Engine driven pump capacity (MDF m3/h 1.5 1.5 1.5 n/a n/a n/a
only)
Fuel flow to engine (without engine m3/h n/a n/a n/a 1.45 1.47 1.47
HFO viscosity before engine cSt 0... 0 0... 0 0... 0 16... 24 16... 24 16... 24
Max. HFO temperature before engine °C 0 0 0 140 140 140

(TE101)
MDF viscosity, min. cSt 1.8 1.8 1.8 1.8 1.8 1.8
3-14 DAAB605808

Engine speed RPM 1200 1200 1200 1200 1200 1200
Max. MDF temperature before engine °C 45 45 45 45 45 45

(TE101)
Fuel consumption at 100% load, HFO g/kWh n/a n/a n/a 198.1 201.6 201.6
Fuel consumption at 100% load, MDF g/kWh 196.1 199.6 199.6 197.9 202.4 201.8
Clean leak fuel quantity, MDF at 100% kg/h 3.24 3.24 3.24 3.24 3.24 3.24
load
Pressure before bearings, nom. kPa 450 450 450 450 450 450
(PT201)
Suction ability main pump, including kPa 20 20 20 20 20 20

pipe loss, max.
Priming pressure, nom. (PT201) kPa 80 80 80 80 80 80
Suction ability priming pump, including kPa 20 20 20 20 20 20

pipe loss, max.
Temperature before bearings, nom. °C 66 66 66 66 66 66

(TE201)
Temperature after engine, approx. °C 78 78 78 78 78 78
Pump capacity (main), engine driven m³/h 34 48 34 34 48 34
Priming pump capacity, 50Hz/60Hz m³/h 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5 8.6 / 10.5
Oil volume, wet sump m³ 0.38 0.5 0.5 0.38 0.5 0.5
Oil volume in separate system oil tank m³ 1.8 1.8 1.8 1.8 1.8 1.8
Filter fineness, nom. mi- 25 25 25 25 25 25

crons
Oil consumption at 100% load, max. g/kWh 0.35 0.35 0.35 0.35 0.35 0.35
Crankcase ventilation flow rate at l/min 780 780 780 780 780 780
100% load
Crankcase ventilation backpressure, kPa 0.3 0.3 0.3 0.3 0.3 0.3
max.
Oil volume in speed governor liters 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2 1.4...2.2

system
Pressure at engine, after pump, nom. kPa 200 + 200 + 200 + 200 + 200 + 200 +
(PT401) static static static static static static
Pressure at engine, after pump, max. kPa 500 350 500 500 350 500
(PT401)
Temperature before cylinder, approx. °C 83 83 83 83 83 83

(TE401)
Temperature after engine, nom. °C 91 91 91 91 91 91
DAAB605808 3-15

Engine speed RPM 1200 1200 1200 1200 1200 1200
Capacity of engine driven pump, nom. m³/h 30 30 30 30 30 30
Pressure drop over engine, total kPa 90 90 90 90 90 90
Pressure drop in external system, max. kPa 120 120 120 120 120 120
Water volume in engine m³ 0.12 0.12 0.12 0.12 0.12 0.12
Pressure from expansion tank kPa 70...150 70...150 70...150 70...150 70...150 70...150

tem
(PT451)
Temperature before engine, min...max °C 25...38 25...38 25...38 25...38 25...38 25...38
Pressure drop over charge air cooler kPa 30 30 30 30 30 30
Pressure drop over oil cooler kPa 30 30 30 30 30 30
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000
Low pressure limit in air vessels kPa 1800 1800 1800 1800 1800 1800
Starting air consumption, start (suc- Nm3 1.2 1.2 1.2 1.2 1.2 1.2
cessful)
Notes:
15°C.
exchangers.

3-16 DAAB605808
3.3.2.3 1200 rpm fuel sulphur content > 0,5%

Engine speed RPM 1200 1200 1200 1200 1200 1200
Engine output kW 1320 1320 1320 1320 1320 1320
Flow at 100% load kg/s 2.5 2.62 2.5 2.5 2.62 2.5

max.
Flow at 100% load kg/s 2.58 2.7 2.58 2.58 2.7 2.58
Flow at 85% load kg/s 2.22 2.28 2.22 2.22 2.28 2.22
Flow at 75% load kg/s 1.98 1.98 1.98 1.98 1.98 1.98
Flow at 50% load kg/s 1.44 1.38 1.44 1.44 1.38 1.44
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Radiation kW 49 49 49 49 49 49
(PT101)

only)

(TE101)
DAAB605808 3-17

Engine speed RPM 1200 1200 1200 1200 1200 1200

(TE101)
load
(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons
100% load
max.

system
(PT401)

(TE401)
3-18 DAAB605808

Engine speed RPM 1200 1200 1200 1200 1200 1200

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

DAAB605808 3-19
3.4 Wärtsilä 8L20

3.4.1 IMO Tier 2
Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200
Engine output kW 1480 1600 1760 1760 1600 1760 1760 1600 1760 1760
Flow at 100% load kg/s 2.8 3.03 3.58 3.58 3.03 3.74 3.74 3.03 3.58 3.58

max.
Flow at 100% load kg/s 2.88 3.12 3.68 3.68 3.12 3.84 3.84 3.12 3.68 3.68
Flow at 85% load kg/s 2.64 2.88 3.12 3.12 2.8 3.2 3.2 2.88 3.12 3.12
Flow at 75% load kg/s 2.32 2.56 2.8 2.8 2.4 2.72 2.72 2.56 2.8 2.8
Flow at 50% load kg/s 1.68 1.84 2.0 2.0 1.6 1.84 1.84 1.84 2.0 2.0
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Radiation kW 64 64 63 63 64 63 63 64 63 63
(PT101)

only)
3-20 DAAB605808

Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200
(TE101)

(TE101)
load
(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons
100% load
max.

system
(PT401)
DAAB605808 3-21

Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200

(TE401)

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

3-22 DAAB605808
3.4.2 SCR Ready

3.4.2.1 900 & 1000 rpm
Engine output kW 1480 1600 1600 1600
Flow at 100% load kg/s 2.8 3.03 3.03 3.03

max.
Flow at 100% load kg/s 2.88 3.12 3.12 3.12
Flow at 85% load kg/s 2.48 2.8 2.72 2.8
Flow at 75% load kg/s 2.16 2.48 2.4 2.48
Flow at 50% load kg/s 1.6 1.6 1.6 1.6

load (TE517)

load (TE517)

load (TE517)

load (TE517)

(PT101)

only)

(TE101)
DAAB605808 3-23

(TE101)
load

(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons

100% load

max.

system
(PT401)

(TE401)
3-24 DAAB605808

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

DAAB605808 3-25

Engine speed RPM 1200 1200 1200 1200 1200 1200
Engine output kW 1760 1760 1760 1760 1760 1760
Flow at 100% load kg/s 3.58 3.74 3.58 3.58 3.74 3.58

max.
Flow at 100% load kg/s 3.68 3.84 3.68 3.68 3.84 3.68
Flow at 85% load kg/s 3.12 3.12 3.12 3.12 3.12 3.12
Flow at 75% load kg/s 2.8 2.72 2.8 2.8 2.72 2.8
Flow at 50% load kg/s 2.0 1.84 2.0 2.0 1.84 2.0
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Radiation kW 63 63 63 63 63 63
(PT101)

only)

(TE101)
3-26 DAAB605808

Engine speed RPM 1200 1200 1200 1200 1200 1200

(TE101)
load
(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons
100% load
max.

system
(PT401)

(TE401)
DAAB605808 3-27

Engine speed RPM 1200 1200 1200 1200 1200 1200

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

3-28 DAAB605808

Engine speed RPM 1200 1200 1200 1200 1200 1200
Engine output kW 1760 1760 1760 1760 1760 1760
Flow at 100% load kg/s 3.34 3.5 3.34 3.34 3.5 3.34

max.
Flow at 100% load kg/s 3.44 3.6 3.44 3.44 3.6 3.44
Flow at 85% load kg/s 2.88 3.04 2.88 2.88 3.04 2.88
Flow at 75% load kg/s 2.64 2.64 2.64 2.64 2.64 2.64
Flow at 50% load kg/s 2.0 1.84 2.0 2.0 1.84 2.0
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Radiation kW 65 65 65 65 65 65
(PT101)

only)

(TE101)
DAAB605808 3-29

Engine speed RPM 1200 1200 1200 1200 1200 1200

(TE101)
load
(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons
100% load
max.

system
(PT401)

(TE401)
3-30 DAAB605808

Engine speed RPM 1200 1200 1200 1200 1200 1200

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

DAAB605808 3-31
3.5 Wärtsilä 9L20

3.5.1 IMO Tier 2
Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200
Engine output kW 1665 1800 1980 1980 1800 1980 1980 1800 1980 1980
Flow at 100% load kg/s 3.15 3.41 4.03 4.03 3.41 4.21 4.21 3.41 4.03 4.03

max.
Flow at 100% load kg/s 3.24 3.51 4.14 4.14 3.51 4.32 4.32 3.51 4.14 4.14
Flow at 85% load kg/s 2.97 3.24 3.6 3.6 3.15 3.6 3.6 3.24 3.6 3.6
Flow at 75% load kg/s 2.61 2.88 3.24 3.24 2.7 3.06 3.06 2.88 3.24 3.24
Flow at 50% load kg/s 1.89 2.07 2.25 2.25 1.8 2.07 2.07 2.07 2.25 2.25
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Radiation kW 72 72 71 71 72 71 71 72 71 71
(PT101)

only)
3-32 DAAB605808

Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200
(TE101)

(TE101)
load
(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons
100% load
max.

system
(PT401)
DAAB605808 3-33

Engine speed RPM 900 1000 1200 1200 1000 1200 1200 1000 1200 1200

(TE401)

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

3-34 DAAB605808
3.5.2 SCR Ready

3.5.2.1 900 & 1000 rpm
Engine output kW 1665 1800 1800 1800
Flow at 100% load kg/s 3.15 3.41 3.41 3.41

max.
Flow at 100% load kg/s 3.24 3.51 3.51 3.51
Flow at 85% load kg/s 2.79 3.15 3.06 3.15
Flow at 75% load kg/s 2.43 2.79 2.7 2.79
Flow at 50% load kg/s 1.8 1.8 1.8 1.8

load (TE517)

load (TE517)

load (TE517)

load (TE517)

(PT101)

only)

(TE101)
DAAB605808 3-35

(TE101)
load

(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons

100% load

max.

system
(PT401)

(TE401)
3-36 DAAB605808

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

DAAB605808 3-37

Engine speed RPM 1200 1200 1200 1200 1200 1200
Engine output kW 1980 1980 1980 1980 1980 1980
Flow at 100% load kg/s 4.03 4.21 4.03 4.03 4.21 4.03

max.
Flow at 100% load kg/s 4.14 4.32 4.14 4.14 4.32 4.14
Flow at 85% load kg/s 3.51 3.51 3.51 3.51 3.51 3.51
Flow at 75% load kg/s 3.15 3.06 3.15 3.15 3.06 3.15
Flow at 50% load kg/s 2.25 2.07 2.25 2.25 2.07 2.25
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Radiation kW 71 71 71 71 71 71
(PT101)

only)

(TE101)
3-38 DAAB605808

Engine speed RPM 1200 1200 1200 1200 1200 1200

(TE101)
load
(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons
100% load
max.

system
(PT401)

(TE401)
DAAB605808 3-39

Engine speed RPM 1200 1200 1200 1200 1200 1200

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

3-40 DAAB605808

Engine speed RPM 1200 1200 1200 1200 1200 1200
Engine output kW 1980 1980 1980 1980 1980 1980
Flow at 100% load kg/s 3.76 3.93 3.75 3.76 3.93 3.75

max.
Flow at 100% load kg/s 3.87 4.05 3.87 3.87 4.05 3.87
Flow at 85% load kg/s 3.33 3.42 3.33 3.33 3.42 3.33
Flow at 75% load kg/s 2.97 2.97 2.97 2.97 2.97 2.97
Flow at 50% load kg/s 2.16 2.07 2.16 2.16 2.07 2.16
load (TE517)
load (TE517)
load (TE517)
load (TE517)
Radiation kW 73 73 73 73 73 73
(PT101)

only)

(TE101)
DAAB605808 3-41

Engine speed RPM 1200 1200 1200 1200 1200 1200

(TE101)
load
(PT201)

pipe loss, max.

pipe loss, max.

(TE201)

crons
100% load
max.

system
(PT401)

(TE401)
3-42 DAAB605808

Engine speed RPM 1200 1200 1200 1200 1200 1200

tem
(PT451)
Starting air system
Pressure, nom. kPa 3000 3000 3000 3000 3000 3000
Pressure, max. kPa 3000 3000 3000 3000 3000 3000
cessful)
Notes:
15°C.
exchangers.

DAAB605808 3-43
NOTE
Fuel consumptions in SCR operation guaranteed only when using Wärtsilä SCR
unit.
NOTE
For proper operation of the Wärtsilä Nitrogen Oxide Reducer (NOR) systems, the
exhaust temperature after the engine needs to be kept within a certain temperature
window. Minimum target temperature are 320°C or 340°C (with liquid fuel)
depending of sulphur content. Please consult your sales contact at Wärtsilä for
more information about SCR Operation.
NOTE
Real-time product information including all technical data covered in this chapter
will be available through Wärtsilä's website (an online tool called Engine Online
Configurators) in late 2019. Please check online for the most updated technical
data when they are available.
3-44 DAAB605808
Wärtsilä 20 Product Guide 4. Description of the Engine
4. Description of the Engine
4.1 Definitions
Fig 4-1 In-line engine definitions (1V93C0029)
4.2 Main components and systems

4.2.1 Engine block
The engine block is a one piece nodular cast iron component with integrated channels for
lubricating oil and cooling water.
The main bearing caps are fixed from below by two hydraulically tensioned screws. They are
guided sideways by the engine block at the top as well as at the bottom. Hydraulically tightened
horizontal side screws at the lower guiding provide a very rigid crankshaft bearing.
4.2.2 Crankshaft
The crankshaft is forged in one piece and mounted on the engine block in an under-slung
way.
4.2.3 Connecting rod

The connecting rod is of forged alloy steel. All connecting rod studs are hydraulically tightened.
Oil is led to the gudgeon pin bearing and piston through a bore in the connecting rod.
4.2.4 Main bearings and big end bearings

The main bearings and the big end bearings are of the Al based bi-metal type with steel back.
4.2.5 Cylinder liner

The cylinder liners are centrifugally cast of a special grey cast iron alloy developed for good
wear resistance and high strength. They are of wet type, sealed against the engine block
metallically at the upper part and by O-rings at the lower part. To eliminate the risk of bore
polishing the liner is equipped with an anti-polishing ring.
DAAB605808 4-1
4. Description of the Engine Wärtsilä 20 Product Guide
4.2.6 Piston
The piston is of composite design with nodular cast iron skirt and steel crown. The piston skirt
is pressure lubricated, which ensures a well-controlled oil flow to the cylinder liner during all
operating conditions. Oil is fed through the connecting rod to the cooling spaces of the piston.
The piston cooling operates according to the cocktail shaker principle. The piston ring grooves
in the piston top are hardened for better wear resistance.
4.2.7 Piston rings

The piston ring set consists of two directional compression rings and one spring-loaded
conformable oil scraper ring. All rings are chromium-plated and located in the piston crown.
4.2.8 Cylinder head

The cylinder head is made of grey cast iron. The thermally loaded flame plate is cooled efficiently
by cooling water led from the periphery radially towards the centre of the head. The bridges
between the valves cooling channels are drilled to provide the best possible heat transfer.
The mechanical load is absorbed by a strong intermediate deck, which together with the upper
deck and the side walls form a box section in the four corners of which the hydraulically
tightened cylinder head bolts are situated. The exhaust valve seats are directly water-cooled.
All valves are equipped with valve rotators.
4.2.9 Camshaft and valve mechanism

There is one cam piece for each cylinder with separate bearing in between. The drop forged
completely hardened camshaft pieces have fixed cams. The camshaft bearing housings are
integrated in the engine block casting and are thus completely closed. The camshaft covers,
one for each cylinder, seal against the engine block with a closed O-ring profile.
The valve tappets are of piston type with self-adjustment of roller against cam to give an even
distribution of the contact pressure. The valve springs ensure that the valve mechanism is
dynamically stable.
Variable Inlet valve Closure (VIC), which is available on IMO Tier 2 engines, offers flexibility to
apply early inlet valve closure at high load for lowest NOx levels, while good part-load
performance is ensured by adjusting the advance to zero at low load.
4.2.10 Camshaft drive

The camshafts are driven by the crankshaft through a gear train.
4.2.11 Fuel injection equipment

The injection pumps are one-cylinder pumps located in the “hot-box”, which has the following
functions:
● Housing for the injection pump element
● Fuel supply channel along the whole engine
● Fuel return channel from each injection pump
● Lubricating oil supply to the valve mechanism
● Guiding for the valve tappets
The injection pumps have built-in roller tappets and are through-flow type to enable heavy
fuel operation. They are also equipped with a stop cylinder, which is connected to the
electro-pneumatic overspeed protection system.
The injection valve is centrally located in the cylinder head and the fuel is admitted sideways
through a high pressure connection screwed in the nozzle holder. The injection pipe between
4-2 DAAB605808
the injection pump and the high pressure connection is well protected inside the hot box. The
high pressure side of the injection system is completely separated from the hot parts of the
exhaust gas components.
4.2.12 Turbocharging and charge air cooling

The selected turbo charger offers the ideal combination of high-pressure ratios and good
efficiency.
The charge air cooler is single stage type and cooled by LT-water.
4.2.13 Charge air waste gate

The charge air wastegate is used to reduce the charge air pressure by bleeding air from the
charge air system.
4.2.14 Exhaust pipes

The complete exhaust gas system is enclosed in an insulated box consisting of easily removable
panels. Mineral wool is used as insulating material.
DAAB605808 4-3
4.3 Cross sections of the engine
Fig 4-2 Cross sections of the engine
4-4 DAAB605808
4.4 Expected Technical Life Time

NOTE
● Service actions are combined to certain overhaul packages and intervals.
Overhaul intervals are typically based on components, which has shortest
technical lifetime. Certain components are also such a type that they need to
be replaced every time, when they are removed from the engine. For these
reasons components recommended overhaul times can be shorter than technical
life time, which is maximum expected lifetime of the component.
● Time Between Overhaul data can be found in Services Engine Operation and
Maintenance Manual (O&MM)
● Achieved life times very much depend on the operating conditions, average
loading of the engine, fuel quality used, fuel handling systems, performance of
maintenance etc. I.e. values given in optimal conditions where Wärtsilä´s all
recommendations are followed.
Component Expected Technical Life Times (h)
MDF HFO1 1) HFO2 1)
Piston crown 60000 48000 42000
Piston rings 20000 14000 10000
Cylinder liner 80000 60000 48000
Cylinder head 60000 56000 50000
Inlet valve and 40000 42000 30000

valve seat insert
Exhaust valve and 40000 28000 2) 20000
valve seat insert
Injection valve 4000 4000 4000
nozzle
Injection pump ele- 28000 28000 20000
ment
Main bearing 60000 48000 42000
Big end bearing 20000 20000 20000
4.4.1 Time between inspection or overhaul

Component Time between inspection or overhaul (h)
MDF HFO1 1) HFO2 1)
Piston crown 20000 14000 10000
Piston rings 20000 14000 10000
Cylinder liner 20000 14000 10000
Cylinder head 20000 14000 10000
Inlet valve and 20000 14000 10000

valve seat insert
Exhaust valve and 20000 14000 10000
valve seat insert
DAAB605808 4-5
Component Time between inspection or overhaul (h)
MDF HFO1 1) HFO2 1)
Injection valve 4000 4000 4000

nozzle
Injection pump ele- 20000 14000 10000
ment
Main bearing 20000 14000 10000
Big end bearing 20000 14000 10000
4-6 DAAB605808
NOTE
1) For detailed information of HFO1 and HFO2 qualities, please see chapter Heavy
Fuel Oil (HFO).
NOTE
Turbocharger lifetime for W20 Dredger applications are 25000 hours for Constant
Speed engines and 50000 hours for Constant Torque engines.
4.5 Engine storage

At delivery the engine is provided with VCI coating and a tarpaulin. For storage longer than 3
months please contact Wärtsilä Finland Oy.
DAAB605808 4-7
Wärtsilä 20 Product Guide 5. Piping Design, Treatment and Installation
5. Piping Design, Treatment and Installation

This chapter provides general guidelines for the design, construction and planning of piping
systems, however, not excluding other solutions of at least equal standard. Installation related
instructions are included in the project specific instructions delivered for each installation.
Fuel, lubricating oil, fresh water and compressed air piping is usually made in seamless carbon
steel (DIN 2448) and seamless precision tubes in carbon or stainless steel (DIN 2391), exhaust
gas piping in welded pipes of corten or carbon steel (DIN 2458). Sea-water piping should be
in Cunifer or hot dip galvanized steel.
NOTE
The pipes in the freshwater side of the cooling water system must not be galvanized!
Attention must be paid to fire risk aspects. Fuel supply and return lines shall be designed so
that they can be fitted without tension. Flexible hoses must have an approval from the
classification society. If flexible hoses are used in the compressed air system, a purge valve
shall be fitted in front of the hose(s).
It is recommended to make a fitting order plan prior to construction.
The following aspects shall be taken into consideration:

● Pockets shall be avoided. When not possible, drain plugs and air vents shall be installed
● Leak fuel drain pipes shall have continuous slope
● Vent pipes shall be continuously rising
● Flanged connections shall be used, cutting ring joints for precision tubes
Maintenance access and dismounting space of valves, coolers and other devices shall be
taken into consideration. Flange connections and other joints shall be located so that
dismounting of the equipment can be made with reasonable effort.
5.1 Pipe dimensions

When selecting the pipe dimensions, take into account:
● The pipe material and its resistance to corrosion/erosion.
● Allowed pressure loss in the circuit vs delivery head of the pump.
● Required net positive suction head (NPSH) for pumps (suction lines).
● In small pipe sizes the max acceptable velocity is usually somewhat lower than in large
pipes of equal length.
● The flow velocity should not be below 1 m/s in sea water piping due to increased risk of
fouling and pitting.
● In open circuits the velocity in the suction pipe is typically about 2/3 of the velocity in the
delivery pipe.
DAAB605808 5-1
5. Piping Design, Treatment and Installation Wärtsilä 20 Product Guide
Table 5-1 Recommended maximum velocities on pump delivery side for guidance
Piping Pipe material Max velocity [m/s]
Fuel oil piping (MDF and HFO) Black steel 1.0
Lubricating oil piping Black steel 1.5
Fresh water piping Black steel 2.5
Sea water piping Galvanized steel 2.5
Aluminum brass 2.5
10/90 copper-nickel-iron 3.0
70/30 copper-nickel 4.5
Rubber lined pipes 4.5
NOTE
The diameter of gas fuel piping depends only on the allowed pressure loss in the
piping, which has to be calculated project specifically.
Compressed air pipe sizing has to be calculated project specifically. The pipe sizes may be
chosen on the basis of air velocity or pressure drop. In each pipeline case it is advised to
check the pipe sizes using both methods, this to ensure that the alternative limits are not being
exceeded.
Pipeline sizing on air velocity: For dry air, practical experience shows that reasonable
velocities are 25...30 m/s, but these should be regarded as the maximum above which noise
and erosion will take place, particularly if air is not dry. Even these velocities can be high in
terms of their effect on pressure drop. In longer supply lines, it is often necessary to restrict
velocities to 15 m/s to limit the pressure drop.
Pipeline sizing on pressure drop: As a rule of thumb the pressure drop from the starting air
vessel to the inlet of the engine should be max. 0.1 MPa (1 bar) when the bottle pressure is 3
MPa (30 bar).
It is essential that the instrument air pressure, feeding to some critical control instrumentation,
is not allowed to fall below the nominal pressure stated in chapter "Compressed air system"
due to pressure drop in the pipeline.
5.2 Trace heating

The following pipes shall be equipped with trace heating (steam, thermal oil or electrical). It
shall be possible to shut off the trace heating.
● All heavy fuel pipes
● All leak fuel and filter flushing pipes carrying heavy fuel
5.3 Pressure class

The pressure class of the piping should be higher than or equal to the design pressure, which
should be higher than or equal to the highest operating (working) pressure. The highest
operating (working) pressure is equal to the setting of the safety valve in a system.
The pressure in the system can:

● Originate from a positive displacement pump
5-2 DAAB605808
● Be a combination of the static pressure and the pressure on the highest point of the pump
curve for a centrifugal pump
● Rise in an isolated system if the liquid is heated
Within this publication there are tables attached to drawings, which specify pressure classes
of connections. The pressure class of a connection can be higher than the pressure class
required for the pipe.
Example 1:
The fuel pressure before the engine should be 0.7 MPa (7 bar). The safety filter in dirty condition
may cause a pressure loss of 0.1 MPa (1.0 bar). The viscosimeter, automatic filter, preheater
and piping may cause a pressure loss of 0.25 MPa (2.5 bar). Consequently the discharge
pressure of the circulating pumps may rise to 1.05 MPa (10.5 bar), and the safety valve of the
pump shall thus be adjusted e.g. to 1.2 MPa (12 bar).
● A design pressure of not less than 1.2 MPa (12 bar) has to be selected.
● The nearest pipe class to be selected is PN16.
● Piping test pressure is normally 1.5 x the design pressure = 1.8 MPa (18 bar).
Example 2:
The pressure on the suction side of the cooling water pump is 0.1 MPa (1 bar). The delivery
head of the pump is 0.3 MPa (3 bar), leading to a discharge pressure of 0.4 MPa (4 bar). The
highest point of the pump curve (at or near zero flow) is 0.1 MPa (1 bar) higher than the nominal
point, and consequently the discharge pressure may rise to 0.5 MPa (5 bar) (with closed or
throttled valves).
● Consequently a design pressure of not less than 0.5 MPa (5 bar) shall be selected.
● The nearest pipe class to be selected is PN6.
● Piping test pressure is normally 1.5 x the design pressure = 0.75 MPa (7.5 bar).
Standard pressure classes are PN4, PN6, PN10, PN16, PN25, PN40, etc.
5.4 Pipe class

Classification societies categorize piping systems in different classes (DNV) or groups (ABS)
depending on pressure, temperature and media. The pipe class can determine:
● Type of connections to be used
● Heat treatment
● Welding procedure
● Test method
Systems with high design pressures and temperatures and hazardous media belong to class
I (or group I), others to II or III as applicable. Quality requirements are highest on class I.
Examples of classes of piping systems as per DNV rules are presented in the table below.
Table 5-2 Classes of piping systems as per DNV rules
Media Class I Class II Class III
MPa (bar) °C MPa (bar) °C MPa (bar) °C
Steam > 1.6 (16) or > 300 < 1.6 (16) and < 300 < 0.7 (7) and < 170
Flammable fluid > 1.6 (16) or > 150 < 1.6 (16) and < 150 < 0.7 (7) and < 60
Other media > 4 (40) or > 300 < 4 (40) and < 300 < 1.6 (16) and < 200
DAAB605808 5-3
5.5 Insulation
The following pipes shall be insulated:
● All trace heated pipes
● Exhaust gas pipes
● Exposed parts of pipes with temperature > 60°C
Insulation is also recommended for:

● Pipes between engine or system oil tank and lubricating oil separator
● Pipes between engine and jacket water preheater
5.6 Local gauges

Local thermometers should be installed wherever a new temperature occurs, i.e. before and
after heat exchangers, etc.
Pressure gauges should be installed on the suction and discharge side of each pump.
5.7 Cleaning procedures

Instructions shall be given at an early stage to manufacturers and fitters how different piping
systems shall be treated, cleaned and protected.
5.7.1 Cleanliness during pipe installation

All piping must be verified to be clean before lifting it onboard for installation. During the
construction time uncompleted piping systems shall be maintained clean. Open pipe ends
should be temporarily closed. Possible debris shall be removed with a suitable method. All
tanks must be inspected and found clean before filling up with fuel, oil or water.
Piping cleaning methods are summarised in table below:
Table 5-3 Pipe cleaning
System Methods
Fuel oil A,B,C,D,F
Lubricating oil A,B,C,D,F
Starting air A,B,C
Cooling water A,B,C
Exhaust gas A,B,C
Charge air A,B,C
1) In case of carbon steel pipes
Methods applied during prefabrication of pipe spools
A = Washing with alkaline solution in hot water at 80°C for degreasing (only if pipes have been greased)
B = Removal of rust and scale with steel brush (not required for seamless precision tubes)
D = Pickling (not required for seamless precision tubes)
Methods applied after installation onboard
5-4 DAAB605808
C = Purging with compressed air
F = Flushing
5.7.2 Fuel oil pipes

Before start up of the engines, all the external piping between the day tanks and the engines
must be flushed in order to remove any foreign particles such as welding slag.
Disconnect all the fuel pipes at the engine inlet and outlet . Install a temporary pipe or hose
to connect the supply line to the return line, bypassing the engine. The pump used for flushing
should have high enough capacity to ensure highly turbulent flow, minimum same as the max
nominal flow. Heaters, automatic filters and the viscosimeter should be bypassed to prevent
damage caused by debris in the piping. The automatic fuel filter must not be used as flushing
filter.
The pump used should be protected by a suction strainer. During this time the welds in the
fuel piping should be gently knocked at with a hammer to release slag and the filter inspected
and carefully cleaned at regular intervals.
The cleanliness should be minimum ISO 4406 (c) 20/18/15, NAS9. A measurement certificate
shows required cleanliness has been reached there is still risk that impurities may occur after
a time of operation.
Note! The engine must not be connected during flushing.
5.7.3 Lubricating oil pipes

Flushing of the piping and equipment built on the engine is not required and flushing oil shall
not be pumped through the engine oil system (which is flushed and clean from the factory).
It is however acceptable to circulate the flushing oil via the engine sump if this is advantageous.
Cleanliness of the oil sump shall be verified after completed flushing and is acceptable when
the cleanliness has reached a level in accordance with ISO 4406 (c) 21/19/15, NAS10. All
pipes connected to the engine, the engine wet sump or to the external engine wise oil tank
shall be flushed. Oil used for filling shall have a cleanliness of ISO 4406 (c) 21/19/15, NAS10.
Note! The engine must not be connected during flushing
5.7.4 Pickling
Prefabricated pipe spools are pickled before installation onboard.
Pipes are pickled in an acid solution of 10% hydrochloric acid and 10% formaline inhibitor for
4-5 hours, rinsed with hot water and blown dry with compressed air.
After acid treatment the pipes are treated with a neutralizing solution of 10% caustic soda
and 50 grams of trisodiumphosphate per litre of water for 20 minutes at 40...50°C, rinsed with
hot water and blown dry with compressed air.
Great cleanliness shall be approved in all work phases after completed pickling.
5.8 Flexible pipe connections

All external pipes must be precisely aligned to the fitting or the flange of the engine to minimize
causing external forces to the engine connection.
Adding adapter pieces to the connection between the flexible pipe and engine, which are not
approved by Wärtsilä are forbidden. Observe that the pipe clamp for the pipe outside the
flexible connection must be very rigid and welded to the steel structure of the foundation to
prevent vibrations and external forces to the connection, which could damage the flexible
connections and transmit noise. The support must be close to the flexible connection. Most
problems with bursting of the flexible connection originate from poor clamping.
DAAB605808 5-5
Proper installation of pipe connections between engines and ship’s piping to be ensured.
● Flexible pipe connections must not be twisted

● Installation length of flexible pipe connections must be correct
● Minimum bending radius must be respected
● Piping must be concentrically aligned
● When specified, the flow direction must be observed
● Mating flanges shall be clean from rust, burrs and anticorrosion coatings
● If not otherwise instructed, bolts are to be tightened crosswise in several stages
● Painting of flexible elements is not allowed
● Rubber bellows must be kept clean from oil and fuel
● The piping must be rigidly supported close to the flexible piping connections.
Fig 5-1 Flexible hoses
Drawing V60L0796 below is showing how pipes shall be clamped.
5-6 DAAB605808
Fig 5-2 Flexible pipe connections (V60L0796)
NOTE
Pressurized flexible connections carrying flammable fluids or compressed air have
to be type approved.
5.9 Clamping of pipes

It is very important to fix the pipes to rigid structures next to flexible pipe connections in order
to prevent damage caused by vibration. The following guidelines should be applied:
● Pipe clamps and supports next to the engine must be very rigid and welded to the steel
structure of the foundation.
● The first support should be located as close as possible to the flexible connection. Next
support should be 0.3-0.5 m from the first support.
● First three supports closest to the engine or generating set should be fixed supports. Where
necessary, sliding supports can be used after these three fixed supports to allow thermal
expansion of the pipe.
● Supports should never be welded directly to the pipe. Either pipe clamps or flange supports
should be used for flexible connection.
Examples of flange support structures are shown in Flange supports of flexible pipe
connections. A typical pipe clamp for a fixed support is shown in Figure 5-4. Pipe clamps
must be made of steel; plastic clamps or similar may not be used.
DAAB605808 5-7
Fig 5-3 Flange supports of flexible pipe connections V60L0796
5-8 DAAB605808
Fig 5-4 Pipe clamp for fixed support (V61H0842A)
DAAB605808 5-9
Wärtsilä 20 Product Guide 6. Fuel Oil System
6. Fuel Oil System
6.1 Acceptable fuel characteristics

The fuel specifications are based on the ISO 8217:2017 (E) standard. Observe that a few
additional properties not included in the standard are listed in the tables. For maximum fuel
temperature before the engine, see chapter "Technical Data".
The fuel shall not contain any added substances or chemical waste, which jeopardizes the
safety of installations or adversely affects the performance of the engines or is harmful to
personnel or contributes overall to air pollution.
6.1.1 Marine Diesel Fuel (MDF)

The fuel specification is based on the ISO 8217:2017(E) standard and covers the fuel grades
ISO-F-DMX, DMA, DFA, DMZ, DFZ, DMB and DFB. These fuel grades are referred to as MDF
(Marine Diesel Fuel).
The distillate grades mentioned above can be described as follows:
● DMX: A fuel quality which is suitable for use at ambient temperatures down to –15 °C
without heating the fuel. Especially in merchant marine applications its use is restricted to
lifeboat engines and certain emergency equipment due to reduced flash point. The low
flash point which is not meeting the SOLAS requirement can also prevent the use in other
marine applications, unless the fuel system is built according to special requirements. Also
the low viscosity (min. 1.4 cSt) can prevent the use in engines unless the fuel can be cooled
down enough to meet the min. injection viscosity limit of the engine.
● DMA: A high quality distillate, generally designated MGO (Marine Gas Oil) in the marine
field.
● DFA: A similar quality distillate fuel compared to DMA category fuels but a presence of
max. 7,0% v/v of Fatty acid methyl ester (FAME) is allowed.
● DMZ: A high quality distillate, generally designated MGO (Marine Gas Oil) in the marine
field. An alternative fuel grade for engines requiring a higher fuel viscosity than specified
for DMA grade fuel.
● DFZ: A similar quality distillate fuel compared to DMZ category fuels but a presence of
● DMB: A general purpose fuel which may contain trace amounts of residual fuel and is
intended for engines not specifically designed to burn residual fuels. It is generally
designated MDO (Marine Diesel Oil) in the marine field.
● DFB: A similar quality distillate fuel compared to DMB category fuels but a presence of
6.1.1.1 Table Light fuel oils
Table 6-1 Distillate fuel specifications
Category ISO-F Test meth-

Lim-
Characteristics Unit od(s) and ref-
it DMX DMA DFA DMZ DFZ DMB DFB
erences
Max 5,500 6,000 6,000 11,00
Kinematic viscosity at 40 °C j) mm2/s a) ISO 3104
Min 1,400 i) 2,000 3,000 2,000
ISO 3675 or
Density at 15 °C kg/m³ Max - 890,0 890,0 900,0
ISO 12185
DAAB605808 6-1
6. Fuel Oil System Wärtsilä 20 Product Guide
Category ISO-F Test meth-

Lim-
Characteristics Unit od(s) and ref-
it DMX DMA DFA DMZ DFZ DMB DFB
erences
Cetane index Min 45 40 40 35 ISO 4264
ISO 8754 or
%
Sulphur b, k) Max 1,00 1,00 1,00 1,50 ISO 14596,
m/m
ASTM D4294
Flash point °C Min 43,0 l) 60,0 60,0 60,0 ISO 2719
Hydrogen sulfide mg/kg Max 2,00 2,00 2,00 2,00 IP 570

mg
Acid number Max 0,5 0,5 0,5 0,5 ASTM D664
KOH/g
%
Total sediment by hot filtration Max - - - 0,10 c) ISO 10307-1
m/m
Oxidation stability g/m³ Max 25 25 25 25 d) ISO 12205
ASTM D7963
Fatty acid methyl ester (FAME) e) % v/v Max - - 7,0 - 7,0 - 7,0
or IP 579
Carbon residue – Micro method %
Max 0,30 0,30 0,30 - ISO 10370
on 10% distillation residue m/m
%
Carbon residue – Micro method Max - - - 0,30 ISO 10370
m/m
winter -16 Report Report -
Cloud point f) °C Max ISO 3015
summer -16 - - -
Cold filter plugging point winter - Report Report - IP 309 or IP

f) °C Max
summer - - - - 612
winter - -6 -6 0
Pour point f) °C Max ISO 3016
summer - 0 0 6
Appearance - Clear and bright g) c) -

ISO 3733
Water % v/v Max - - - 0,30 c) or ASTM
D6304-C m)
%
Ash Max 0,010 0,010 0,010 0,010 ISO 6245
m/m
Lubricity, corr. wear scar diam. h) µm Max 520 520 520 520 d) ISO 12156-1
6-2 DAAB605808
NOTE
a) 1 mm²/s = 1 cSt.
b) Notwithstanding the limits given, the purchaser shall define the maximum sulphur
content in accordance with relevant statutory limitations.
c) If the sample is not clear and bright, the total sediment by hot filtration and water
tests shall be required.
d) If the sample is not clear and bright, the Oxidation stability and Lubricity tests
cannot be undertaken and therefore, compliance with this limit cannot be shown.
e) See ISO 8217:2017(E) standard for details.
f) Pour point cannot guarantee operability for all ships in all climates. The purchaser
should confirm that the cold flow characteristics (pour point, cloud point, cold filter
clogging point) are suitable for ship’s design and intended voyage.
g) If the sample is dyed and not transparent, see ISO 8217:2017(E) standard for
details related to water analysis limits and test methods.
h) The requirement is applicable to fuels with a sulphur content below 500 mg/kg
(0,050 % m/m).
Additional notes not included in the ISO 8217:2017(E) standard:
i) Low min. viscosity of 1,400 mm²/s can prevent the use ISO-F-DMX category
fuels in Wärtsilä® 4-stroke engines unless a fuel can be cooled down enough to
meet the specified min. injection viscosity limit.
j) Allowed kinematic viscosity before the injection pumps for this engine type is
1,8 - 24 mm²/s.
k) There doesn’t exist any minimum sulphur content limit for Wärtsilä® 4-stroke
diesel engines and also the use of Ultra Low Sulphur Diesel (ULSD) is allowed
provided that the fuel quality fulfils other specified properties.
l) Low flash point of min. 43 °C can prevent the use ISO-F-DMX category fuels in
Wärtsilä® engines in marine applications unless the ship’s fuel system is built
according to special requirements allowing the use or that the fuel supplier is able
to guarantee that flash point of the delivered fuel batch is above 60 °C being a
requirement of SOLAS and classification societies.
m) Alternative test method.
DAAB605808 6-3
6.1.2 0,10% m/m sulphur fuels for SECA areas

Due to the tightened sulphur emission legislation being valid since 01.01.2015 in the specified
SECA areas many new max. 0,10 % m/m sulphur content fuels have entered the market.
Some of these fuels are not pure distillate fuels, but contain new refinery streams, like
hydrocracker bottoms or can also be blends of distillate and residual fuels. The new 0,10 %
m/m sulphur fuels are also called as Ultra Low Sulphur Fuel Oils (ULSFO) or “hybrid” fuels,
since those can contain properties of both distillate and residual fuels. In the existing ISO
8217:2017(E) standard the fuels are classed as RMA 10, RMB 30 or RMD 80, if not fulling the
DM grade category requirements, though from their properties point of view this is generally
not an optimum approach.
These fuels can be used in the Wärtsilä 20 engine type, but special attention shall be paid to
optimum operating conditions. See also Services Instruction WS02Q312.
RMA RMB RMD Test method

Characteristics Unit
10 30 80 reference
mm2/s 6,0 - 6,0 - 6,0 -
Kinematic viscosity bef. inj. pumps c) a) -
24 24 24
mm2/s
Kinematic viscosity at 50 °C, max. a) 10,00 30,00 80,00 ISO 3104
ISO 3675 or ISO

Density at 15 °C, max. kg/m3 920,0 960,0 975,0
12185
CCAI, max. e) - 850 860 860 ISO 8217, Annex F
% ISO 8574 or ISO
Sulphur, max.b), f) 0,10 0,10 0,10
m/m 14596
Flash point, min. °C 60,0 60,0 60,0 ISO 2719
Hydrogen sulfide, max. mg/kg 2,00 2,00 2,00 IP 570

mg
Acid number, max. 2,5 2,5 2,5 ASTM D664
KOH/g
%
Total sediment existent, max. 0,10 0,10 0,10 ISO 10307-2
m/m
%
Carbon residue, micro method, max. 2,50 10,00 14,00 ISO 10370
m/m
%
Asphaltenes, max. c) 1,5 6,0 8,0 ASTM D3279
m/m
Pour point (upper), max., winter quality
d) °C 0 0 30 ISO 3016
Pour point (upper), max., summer quality

d) °C 6 6 30 ISO 3016
ISO 3733 or ASTM

Water max. % v/v 0,30 0,50 0,50
D6304-C c)
ISO 3733 or ASTM
Water bef. engine, max. c) % v/v 0,30 0,30 0,30
D6304-C c)
% ISO 6245 or
Ash, max. 0,040 0,070 0,070
m/m LP1001 c, h)
IP 501, IP 470 or
Vanadium, max. f) mg/kg 50 150 150
ISO 14597
Sodium, max. f) mg/kg 50 100 100 IP 501 or IP 470
Sodium bef. engine, max. c, f) mg/kg 30 30 30 IP 501 or IP 470
6-4 DAAB605808
RMA RMB RMD Test method

Characteristics Unit
10 30 80 reference
IP 501, IP 470 or
Aluminium + Silicon, max. mg/kg 25 40 40
ISO 10478
IP 501, IP 470 or
Aluminium + Silicon bef. engine, max.c) mg/kg 15 15 15
ISO 10478
Used lubricating oil: g)
- Calcium, max. mg/kg 30 30 30 IP 501 or IP 470
- Zinc, max. mg/kg 15 15 15 IP 501 or IP 470
- Phosphorus, max. mg/kg 15 15 15 IP 501 or IP 500
NOTE
a) 1 mm²/s = 1 cSt.
b) The purchaser shall define the maximum sulphur content in accordance with
relevant statutory limitations.
c) Additional properties specified by the engine manufacturer, which are not
included in the ISO 8217:2017(E) standard.
d) Purchasers shall ensure that this pour point is suitable for the equipment on
board / at the plant, especially if the ship operates / plant is located in cold climates.
e) Straight run residues show CCAI values in the 770 to 840 range and are very
good ignitors. Cracked residues delivered as bunkers may range from 840 to – in
exceptional cases – above 900. Most bunkers remain in the max. 850 to 870 range
at the moment. CCAI value cannot always be considered as an accurate tool to
determine fuels’ ignition properties, especially concerning fuels originating from
modern and more complex refinery processes.
f) Sodium contributes to hot corrosion on exhaust valves when combined with
high sulphur and vanadium contents. Sodium also strongly contributes to fouling
of the exhaust gas turbine blading at high loads. The aggressiveness of the fuel
depends on its proportions of sodium and vanadium, but also on the total amount
of ash. Hot corrosion and deposit formation are, however, also influenced by other
ash constituents. It is therefore difficult to set strict limits based only on the sodium
and vanadium content of the fuel. Also a fuel with lower sodium and vanadium
contents than specified above, can cause hot corrosion on engine components.
g) The fuel shall be free from used lubricating oil (ULO). A fuel shall be considered
to contain ULO when either one of the following conditions is met:
● Calcium > 30 mg/kg and zinc > 15 mg/kg OR
● Calcium > 30 mg/kg and phosphorus > 15 mg/kg
h) Ashing temperatures can vary when different test methods are used having an
influence on the test result.
DAAB605808 6-5
6.1.3 Heavy Fuel Oil (HFO)

Residual fuel grades are referred to as HFO (Heavy Fuel Oil). The fuel specification HFO 2 is
based on the ISO 8217:2017(E) standard and covers the categories ISO-F-RMA 10 to RMK
700. Fuels fulfilling the specification HFO 1 permit longer overhaul intervals of specific engine
components than HFO 2.
6.1.3.1 Table Heavy fuel oils
Table 6-2 Residual fuel specifications
Limit Limit
Characteristics Unit Test method reference
HFO 1 HFO 2
Kinematic viscosity bef. inj. pumps d) mm2/s b) 20 ± 4 20 ± 4 -
Kinematic viscosity at 50 °C, max. mm2/s b) 700,0 700,0 ISO 3104
Density at 15 °C, max. 991,0 / 991,0 /
kg/m3 ISO 3675 or ISO 12185
1010,0 a) 1010,0 a)
CCAI, max. f) - 850 870 ISO 8217, Annex F
Sulphur, max. c, g) Statutory require-
%m/m ISO 8754 or ISO 14596
ments
Flash point, min. °C 60,0 60,0 ISO 2719
Hydrogen sulfide, max. mg/kg 2,00 2,00 IP 570
Acid number, max. mg KOH/g 2,5 2,5 ASTM D664
Total sediment aged, max. %m/m 0,10 0,10 ISO 10307-2
Carbon residue, micro method, max. %m/m 15,00 20,00 ISO 10370
Asphaltenes, max. d) %m/m 8,0 14,0 ASTM D3279
Pour point (upper), max. e) °C 30 30 ISO 3016
Water, max. d) ISO 3733 or ASTM
%V/V 0,50 0,50
D6304-C d)
Water before engine, max. d) ISO 3733 or ASTM
%V/V 0,30 0,30
D6304-C d)
Ash, max. %m/m 0,050 0,150 ISO 6245 or LP1001 d, i)
Vanadium, max. g) IP 501, IP 470 or ISO

mg/kg 100 450
14597
Sodium, max. g) mg/kg 50 100 IP 501 or IP 470
Sodium before engine, max. d, g) mg/kg 30 30 IP 501 or IP 470
Aluminium + Silicon, max. d) IP 501, IP 470 or ISO
mg/kg 30 60
10478
Aluminium + Silicon before engine, max. IP 501, IP 470 or ISO
d) mg/kg 15 15
10478
Used lubricating oil h)
- Calcium, max. mg/kg 30 30 IP 501 or IP 470
- Zinc, max. mg/kg 15 15 IP 501 or IP 470
- Phosphorus, max. mg/kg 15 15 IP 501 or IP 500
6-6 DAAB605808
NOTE
a) Max. 1010 kg/m³ at 15 °C, provided the fuel treatment system can reduce water
and solids (sediment, sodium, aluminium, silicon) before engine to the specified
levels.
b) 1 mm²/s = 1 cSt.
c) The purchaser shall define the maximum sulphur content in accordance with
relevant statutory limitations.
d) Additional properties specified by the engine manufacturer, which are not
included in the ISO 8217:2017(E) standard.
e) Purchasers shall ensure that this pour point is suitable for the equipment on
board / at the plant, especially if the ship operates / plant is located in cold climates.
f) Straight run residues show CCAI values in the 770 to 840 range and are very
good ignitors. Cracked residues delivered as bunkers may range from 840 to – in
exceptional cases – above 900. Most bunkers remain in the max. 850 to 870 range
at the moment. CCAI value cannot always be considered as an accurate tool to
determine fuels’ ignition properties, especially concerning fuels originating from
modern and more complex refinery processes.
g) Sodium contributes to hot corrosion on exhaust valves when combined with
high sulphur and vanadium contents. Sodium also strongly contributes to fouling
of the exhaust gas turbine blading at high loads. The aggressiveness of the fuel
depends on its proportions of sodium and vanadium, but also on the total amount
of ash. Hot corrosion and deposit formation are, however, also influenced by other
ash constituents. It is therefore difficult to set strict limits based only on the sodium
and vanadium content of the fuel. Also a fuel with lower sodium and vanadium
contents than specified above, can cause hot corrosion on engine components.
h) The fuel shall be free from used lubricating oil (ULO). A fuel shall be considered
to contain ULO when either one of the following conditions is met:
● Calcium > 30 mg/kg and zinc > 15 mg/kg OR
● Calcium > 30 mg/kg and phosphorus > 15 mg/kg
i) The ashing temperatures can vary when different test methods are used having
an influence on the test result.
6.1.4 Biofuel oils

Liquid biofuel characteristics and specifications
The diesel engines are designed and developed with a dedicated kit for continuous operation,
without reduction in the rated output, on liquid biofuels with the properties included in the
table 6.1.4.1, table 6.1.4.2 and table 6.1.4.3.
NOTE
Liquid biofuels included in the table 6.1.4.1 and table 6.1.4.2 have typically lower
heating value than fossil fuels, therefore the capacity of fuel injection system
influencing on guaranteed engine output must be checked case by case.
NOTE
Liquid biofuels included in the table 6.1.4.3 have a low density, while the capacity
of fuel injection system influencing on guaranteed engine output must be checked
case by case. The flash point can also be lower than 60 °C which is a requirement
of SOLAS and Classification societies (for marine applications). Therefore its use
might be prohibited.
DAAB605808 6-7
Acceptable storage period for liquid biofuels excluding products which belong to the category
being presented in 6.1.4.3 can be significantly shorter than storage period specified for fossil
fuels. Some biodiesel manufacturers are referring to max. one month storage period. After
that acidity starts to increase leading to faster oxidation rate of the fuel.
Blending of different fuel qualities:

Crude and refined liquid biofuels (table 6.1.4.1) must not be mixed with fossil fuels, but have
to be used as such.
Mixing of crude and refined liquid biofuel (table 6.1.4.1) and distillate fuel will increase the risk
of cavitation in the fuel system, since required fuel temperature before engine is normally 80
- 90 °C. At this temperature light fractions of distillate fuel have already started to evaporate.
Mixing of crude and refined liquid biofuel (table 6.1.4.1) with residual fuel will increase the risk
of biofuel component polymerization leading to formation of gummy deposits to engine
component surfaces, because of elevated temperature.
The use of residual fuel requires much higher operating temperature than the use of crude
and refined liquid biofuel, i.e. normally above 100 °C in order to achieve a proper fuel injection
viscosity.
Required fuel temperatures:

Crude and refined liquid biofuel (table 6.1.4.1) temperature before an engine is an utmost
important operating parameter. Too low temperature will cause solidification of fatty acids
leading to clogging of filters, plug formation in the fuel system and even to fuel injection
equipment component breakdowns. Too high fuel temperature will increase the risk of
polymerization and formation of gummy deposits, especially in the presence of oxygen.
When operating on crude and refined liquid biofuels (table 6.1.4.1), it is utmost important to
maintain a proper fuel temperature before fuel injection pumps in order to ensure safe operation
of the engine and fuel system. The recommended fuel operating temperature depends on
both the liquid biofuel quality and the degree of processing. E.g. many palm oil qualities require
~ 80 - 90 °C fuel temperature in order to achieve an expected lifetime of fuel injection equipment
and to avoid fuel filter clogging. Some refined palm oil qualities are however behaving
acceptably also at lower, ~ 70 - 75 °C operating temperature. For other types of crude and
refined liquid biofuels the temperature requirement can be slightly different and must be
confirmed before the use.
For fuel qualities included in the table 6.1.4.2 and table 6.1.4.3 fuel temperature before fuel
injection pumps is limited to max. 45 °C.
6.1.4.1 Crude and refined liquid biofuels

The specification included in the table below is valid for crude and refined liquid biofuels, like
palm oil, coconut oil, copra oil, rape seed oil, jatropha oil, fish oil, etc.
Table 6-3 Liquid biofuel specification for crude and refined biofuels (residual fuel
substitutes)
Property Unit Limit Test method reference

mm2/s @ 50
°C 70 1)
Viscosity, max. ISO 3104
mm2/s @ 80 15 1)
°C
Injection viscosity, min. mm2/s 1.8 2) ISO 3104
6-8 DAAB605808
Injection viscosity, max. mm2/s 24 ISO 3104

kg/m3 @ 15
Density, max. 940 ISO 3675 or ISO 12185
°C
Ignition properties 3) 3) FIA-100 FCA test
Sulphur, max. % m/m 0.05 ISO 8754
Total sediment existent, max. % m/m 0.05 ISO 10307-1
Water, max. before engine % v/v 0.20 ISO 3733
Micro carbon residue, max. % m/m 0.50 ISO 10370
Ash, max. % m/m 0.05 ISO 6245 / LP1001 4)
Phosphorus, max. mg/kg 100 ISO 10478
Silicon, max. mg/kg 15 ISO 10478
Alkali content (Na+K), max. mg/kg 30 ISO 10478
Flash point (PMCC), min. °C 60 ISO 2719
Cloud point, max. °C 5) ISO 3015
Cold filter plugging point, max. °C 5) IP 309

Copper strip corrosion (3 hrs @ 50 °C),
Rating 1b ASTM D130
max.
Steel corrosion (24 / 72 hours @ 20, 60 No signs of
Rating LP 2902
and 120 °C), max. corrosion
Oxidation stability @ 110 °C, min. h 17.0 6) EN 14112
Acid number, max. mg KOH/g 15.0 ASTM D664
Strong acid number, max. mg KOH/g 0.0 ASTM D664

g iodine /100
Iodine number, max. 120 7) ISO 3961
g
Synthetic polymers % m/m Report 8) LP 2501
DAAB605808 6-9
NOTE
1) If injection viscosity of max. 24 cSt cannot be achieved with an unheated fuel,
fuel system has to be equipped with a heater (mm²/s = cSt).
2) Min. viscosity limit at engine inlet in running conditions (mm²/s = cSt).
3) Ignition properties have to be equal to or better than the requirements for fossil
fuels, i.e., CI min. 35 for LFO and CCAI max. 870 for HFO.
4) Ashing temperatures can vary when different test methods are used having an
influence on the test result.
5) Cloud point and cold filter plugging point have to be at least 10 °C below fuel
injection temperature and the temperature in the whole fuel system has to be min.
10 – 15 °C higher than cloud point and cold filter plugging point.
6) A lower oxidation stability value down to min. 10 hours can be considered
acceptable if other fuel properties, like cloud point, cold filter plugging point and
viscosity support that. This needs to be decided case-by-case.
7) Iodine number of soyabean oil is somewhat higher, up to ~ 140, which is
acceptable for specific that biofuel quality.
8) Biofuels originating from food industry can contain synthetic polymers, like e.g.
styrene, propene and ethylene used in packing material. Such compounds can
cause filter clogging and shall thus not be present in biofuels.
NOTE
If SCR or oxidation catalyst needs to be used the specification included in the
table above does not apply, but the fuel quality requirements have to be discussed
separately. The specification does not take into consideration Particulate Matter
emission limits.
NOTE
The use of liquid biofuels fulfilling the table above requirements always require a
NSR to be made.
6.1.4.2 Fatty acid methyl ester (FAME) / Biodiesel

Renewable refined liquid biofuels which are manufactured by using transesterification
processes, can contain both vegetable and / or animal based feedstock and do normally show
out very good physical and chemical properties. These fuels can be used provided that the
specification included in the table below is fulfilled. International standards ASTM D 6751-06
or EN 14214:2012 (E) are typically used for specifying biodiesel quality.
Table 6-4 Fatty acid methyl ester (FAME) / Biodiesel specification based on the EN
14214:2012 standard

mm2/s @ 40
Viscosity, min. - max. 3.5 - 5.0 EN ISO 3104
°C
Injection viscosity, min. mm2/s 1.8 1) EN ISO 3104
kg/m3 @ 15
Density, min. - max. 860 - 900 EN ISO 3675 / 12185
°C
Cetane number, min. - 51.0 EN ISO 5165
6-10 DAAB605808
Sulphur content, max. mg/kg 10.0 EN ISO 20846 / 20884 / 13032
Sulphated ash content, max. % m/m 0.02 ISO 3987
Total contamination, max. mg/kg 24 EN 12662
Water content, max. mg/kg 500 EN ISO 12937
Phosphorus content, max. mg/kg 4.0 EN 14107
Group I metals (Na + K) content, max. mg/kg 5.0 EN 14108 / EN 14109 / 14538
Group II metals (Ca + Mg) content, max. mg/kg 5.0 EN 14538
Flash point, min. °C 101 EN ISO 2719A / 3679

Cold filter plugging point, max. (climate
°C -20 → +5 2) EN 116
dependent requirement)
Oxidation stability @ 110 °C, min. h 8.0 EN 14112
Rating Class 1 EN ISO 2160
max.
Acid value, max. mg KOH/g 0.50 EN 14104
Iodine value, max. g iodine/100 g 120 EN 14111 / 16300
FAME content, min. % m/m 96.5 EN 14103
Linolenic acid methyl ester, max. % m/m 12.0 EN 14103

Polyunsaturated ( ≥ 4 double bonds)
% m/m 1.00 EN 15779
methyl esters, max.
Methanol content, max. % m/m 0.20 EN 14110
Monoglyceride content, max. % m/m 0.70 EN 14105
Diglyceride content, max. % m/m 0.20 EN 14105
Triglyceride content, max. % m/m 0.20 EN 14105
Free glycerol, max. % m/m 0.02 EN 14105 / EN 14106
Total glycerol, max. % m/m 0.25 EN 14105
NOTE
1) Min. limit at engine inlet in running conditions (mm²/s = cSt).
2) Cold flow properties of renewable biodiesel can vary based on the geographical
location and also based on the feedstock properties, which issues must be taken
into account when designing the fuel system. For arctic climates even lower CFPP
values down to -44 °C are specified.
NOTE
The use of liquid biofuels fulfilling the table above requirements always require a
NSR to be made.
6.1.4.3 Paraffinic diesel fuels from synthesis and hydrotreatment

Paraffinic renewable distillate fuels originating from synthesis or hydrotreatment represent
clearly a better quality than transesterfied biodiesel and the comparison to biodiesel quality
requirements is thus so relevant. The quality of the fuel qualities shall meet the EN 15940:2016
DAAB605808 6-11
Class A requirements included in the table below. For arctic or severe winter climates additional
or more stringent requirements are set concerning cold filter plugging point, cloud point,
viscosity and distillation properties.
Table 6-5 Requirements for paraffinic diesel from synthesis or hydrotreatment based
on the EN 15940:2016 standard

mm2/s @ 40
Viscosity, min. - max. 2.0 - 4.5 EN ISO 3104
°C
Injection viscosity, min. mm2/s 1.8 1) EN ISO 3104
kg/m3 @ 15
Density, min. - max. 765 - 800 2) EN ISO 3675 / 12185
°C
Cetane number, min. - 70.0 EN 15195 / EN ISO 5165
Sulphur content, max. mg/kg 5.0 EN ISO 20846 / 20884
Ash content, max. % m/m 0.010 EN ISO 6245
Total contamination, max. mg/kg 24 EN 12662
Water content, max. mg/kg 200 EN ISO 12937
Total aromatics, max. % m/m 1.1 EN 12916

Carbon residue on 10% distillation
% m/m 0.30 EN ISO 10370
residue, max.
Lubricity, max. µm 460 EN ISO 12156-1
Flash point, min. °C 55 3) EN ISO 2719

Cold filter plugging point, max. (climate
°C -20 → +5 4) EN 116 / 16329
dependent requirement)
Oxidation stability, max. g/m3 25 EN ISO 12205
Oxidation stability, min. h 20 5) EN 15751
Rating Class 1 EN ISO 2160
max.
Distillation EN ISO 3405 / 3924
% v/v recovered @ 250 °C, max. % v/v 65
% v/v recovered @ 350 °C, min. % v/v 85
95 % v/v recovered at, max. °C 360

Distillation EN ISO 3405 / 3924
% v/v recovered @ 250 °C, max. % v/v 65
% v/v recovered @ 350 °C, min. % v/v 85
95 % v/v recovered at, max. °C 360
FAME content, max. % v/v 7.0 EN 14078
6-12 DAAB605808
NOTE
1) Min. limit at engine inlet in running conditions (mm²/s = cSt).
2) Due to low density the guaranteed engine output of pure hydrotreated fuel /
GTL has to be confirmed case by case.
3) The use in marine applications is allowed provided that a fuel supplier can
guarantee min. flash point of 60 °C.
4) Cold flow properties of renewable biodiesel can vary based on the geographical
location and also based on the feedstock properties, which issues must be taken
into account when designing the fuel system. For arctic or severe winter climates
even lower CFPP values down to -44 °C are specified.
5) Additional requirement if the fuel contains > 2.0 % v/v of FAME.
NOTE
The use of liquid biofuels fulfilling the table above requirements is allowed in all
Wärtsilä medium-speed diesel and DF engines both as main fuel, back-up fuel
and pilot fuel.
DAAB605808 6-13
6.2 Internal fuel oil system
NOTE
T = Test plug
Fig 6-1 Internal fuel oil system, HFO/LFO (DAAF382587B) - UNIC C1
System components:
01 Injection pump 04 Adjustable orifice
02 Injection valve 05 Pulse damper
03 Fuel leakage collector
Sensors and indicators:
PT101 Fuel oil leakage, engine inlet
TE101 Fuel oil temperature, engine inlet
TI101 Fuel oil temperature, engine inlet
LS103A Fuel oil leakage, clean primary
Pipe connections: Size Standard
101 Fuel inlet OD18 DIN 2353
102 Fuel outlet OD18 DIN 2353
103 Leak fuel drain, clean fuel OD18 DIN 2353
1041 Leak fuel drain, dirty fuel free end OD18 DIN 2353
1043 Leak fuel drain, dirty fuel flywheel end OD18 DIN 2353
6-14 DAAB605808
Fig 6-2 Internal fuel system, MDF & HFO (DAAF395502D) - UNIC C2 & UNIC 2.0
System components:
01 Injection pump 05 Pulse damper
02 Injection valve 06 Duplex fine filter
03 Fuel leakage collector 07 Engine driven fuel feed pump
04 Adjustable orifice 08 Pressure regulating valve
PT101 Fuel oil pressure, engine inlet PDS113 Fuel oil filter, pressure difference switch
*PT110 Fuel oil pressure, stand-by pump (optional) TE101 Fuel oil temperature, engine inlet
LS103A Fuel oil leakage, clean primary TI101 Fuel oil temperature, engine inlet
**PS110 Fuel oil stand-by pump start
Pipe connections Size
101 Fuel inlet OD28
102 Fuel outlet OD28
103 Leak fuel drain, clean fuel OD18
1041 Leak fuel drain, dirty fuel free end OD22
1043 Leak fuel drain, dirty fuel flywheel end OD18
105 Fuel stand-by connection OD22
DAAB605808 6-15
The engine can be specified to either operate on heavy fuel oil (HFO) or on marine diesel fuel
(MDF). The engine is designed for continuous operation on HFO. It is however possible to
operate HFO engines on MDF intermittently without alternations. If the operation of the engine
is changed from HFO to continuous operation on MDF, then a change of exhaust valves from
Nimonic to Stellite is recommended.
HFO engines are equipped with an adjustable orifice in the fuel return line on the engine. For
engines installed in the same fuel feed circuit, it is essential to distribute the fuel correctly to
the engines. For this purpose the pressure drop differences around engines shall be
compensated with the adjustable orifice.
MDF engines, with an engine driven fuel feed pump, are equipped with a pressure control
valve in the fuel return line on the engine. This pressure control valve maintains desired pressure
before the injection pumps.
6.2.1 Leak fuel system

Clean leak fuel from the injection valves and the injection pumps is collected on the engine
and drained by gravity through a clean leak fuel connection. The clean leak fuel can be re-used
without separation. The quantity of clean leak fuel is given in chapter Technical data.
Other possible leak fuel and spilled water and oil is separately drained from the hot-box through
dirty fuel oil connections and it shall be led to a sludge tank.
6-16 DAAB605808
6.3 External fuel oil system

The design of the external fuel system may vary from ship to ship, but every system should
provide well cleaned fuel of correct viscosity and pressure to each engine. Temperature control
is required to maintain stable and correct viscosity of the fuel before the injection pumps (see
Technical data). Sufficient circulation through every engine connected to the same circuit must
be ensured in all operating conditions.
The fuel treatment system should comprise at least one settling tank and two separators.
Correct dimensioning of HFO separators is of greatest importance, and therefore the
recommendations of the separator manufacturer must be closely followed. Poorly centrifuged
fuel is harmful to the engine and a high content of water may also damage the fuel feed system.
Injection pumps generate pressure pulses into the fuel feed and return piping.
The fuel pipes between the feed unit and the engine must be properly clamped to rigid
structures. The distance between the fixing points should be at close distance next to the
engine. See chapter Piping design, treatment and installation.
A connection for compressed air should be provided before the engine, together with a drain
from the fuel return line to the clean leakage fuel or overflow tank. With this arrangement it is
possible to blow out fuel from the engine prior to maintenance work, to avoid spilling.
NOTE
In multiple engine installations, where several engines are connected to the same
fuel feed circuit, it must be possible to close the fuel supply and return lines
connected to the engine individually. This is a SOLAS requirement. It is further
stipulated that the means of isolation shall not affect the operation of the other
engines, and it shall be possible to close the fuel lines from a position that is not
rendered inaccessible due to fire on any of the engines.
6.3.1 Low sulphur operation

For newbuildings expected to operate purely within SECAs, fuel and lubricating oil filling,
storage, transfer, separation, and supply systems can in principle be arranged as on a traditional
HFO ship.
However, if intention is to operate on different fuel quailties inside and outside SECAs it is
beneficial to install double bunker tanks, settling tanks, service tanks and leak fuel tanks in
order to avoid mixing incompatible fuels. Also check if flexible lube oil systems is needed, in
order to avoid operation with high-sulphur fuel and too low lube oil BN.
6.3.2 Definitions Filtration term used

● mesh size: opening of the mesh (surface filtration), and often used as commercial name
at purchase. Only approximately related to Efficiency and Beta-value. Insufficient to compare
two filters from two suppliers. Good to compare two meshes of same filter model from
same supplier. Totally different than micron absolute, that is always much bigger size in
micron.
- e.g. a real example: 30 micron mesh size = approx. 50 micron ß50 = 75
● XX micron, nominal: commercial name of that mesh, at purchase. Not really related to
filtration capability, especially when comparing different suppliers. Typically, a totally
different value than XX micron, absolute.
- e.g. a real example: 10 micron nominal (ß10 = 60%) = approx. 60 micron absolute.
● XX micron, absolute: intended here as ßxx = 75 ISO 16889 (similar to old exx = 98,7% )
- Beta value ßXX = YY : ISO name with ISO 16889 standardised test method. Weak
repeteability for dust bigger than 25..45 microns.
- Example: ß20 = 75 means “every 75 particles 20 micron ISO dust sent, one passes”.
DAAB605808 6-17
- Efficiency ßXX = YY % : same meaning as Beta-value, but not any ISO standardised test
method, hence sometimes used for particles larger than 25..45 micron.
- Example: ß20 = 98,7% means “every 75 particles 20 micron non-ISO dust sent, one
passes, which is 98,7% stopped.”
6.3.3 Fuel heating requirements HFO

Heating is required for:
● Bunker tanks, settling tanks, day tanks
● Pipes (trace heating)
● Separators
● Fuel feeder/booster units
To enable pumping the temperature of bunker tanks must always be maintained 5...10°C
above the pour point, typically at 40...50°C. The heating coils can be designed for a temperature
of 60°C.
The tank heating capacity is determined by the heat loss from the bunker tank and the desired
temperature increase rate.
6-18 DAAB605808
Fig 6-3 Fuel oil viscosity-temperature diagram for determining the pre-heating
temperatures of fuel oils (4V92G0071b)
Example 1: A fuel oil with a viscosity of 380 cSt (A) at 50°C (B) or 80 cSt at 80°C (C) must be
pre-heated to 115 - 130°C (D-E) before the fuel injection pumps, to 98°C (F) at the separator
and to minimum 40°C (G) in the bunker tanks. The fuel oil may not be pumpable below 36°C
(H).
To obtain temperatures for intermediate viscosities, draw a line from the known
viscosity/temperature point in parallel to the nearest viscosity/temperature line in the diagram.
Example 2: Known viscosity 60 cSt at 50°C (K). The following can be read along the dotted
line: viscosity at 80°C = 20 cSt, temperature at fuel injection pumps 74 - 87°C, separating
temperature 86°C, minimum bunker tank temperature 28°C.
6.3.4 Fuel tanks

The fuel oil is first transferred from the bunker tanks to settling tanks for initial separation of
sludge and water. After centrifuging the fuel oil is transferred to day tanks, from which fuel is
supplied to the engines.
6.3.4.1 Settling tank, HFO (1T02) and MDF (1T10)

Separate settling tanks for HFO and MDF are recommended.
DAAB605808 6-19
In case intention is to operate on low sulphur fuel it is beneficial to install double settling tanks
to avoid incompability problems.
To ensure sufficient time for settling (water and sediment separation), the capacity of each
tank should be sufficient for min. 24 hours operation at maximum fuel consumption. The tanks
should be provided with internal baffles to achieve efficient settling and have a sloped bottom
for proper draining. The temperature in HFO settling tanks should be maintained between
50°C and 70°C, which requires heating coils and insulation of the tank. Usually MDF settling
tanks do not need heating or insulation, but the tank temperature should be in the range
20...40°C.
6.3.4.2 Day tank, HFO (1T03) and MDF (1T06)

Two day tanks for HFO are to be provided, each with a capacity sufficient for at least 8 hours
operation at maximum fuel consumption. A separate tank is to be provided for MDF. The
capacity of the MDF tank should ensure fuel supply for 8 hours. Settling tanks may not be
used instead of day tanks.
In case intention is to operate on different fuel qualities (low sulphur fuel) it is beneficial to
install double day tanks to avoid incompability problems.
The day tank must be designed so that accumulation of sludge near the suction pipe is
prevented and the bottom of the tank should be sloped to ensure efficient draining. HFO day
tanks shall be provided with heating coils and insulation. It is recommended that the viscosity
is kept below 140 cSt in the day tanks. Due to risk of wax formation, fuels with a viscosity
lower than 50 cSt at 50°C must be kept at a temperature higher than the viscosity would
require. Continuous separation is nowadays common practice, which means that the HFO
day tank temperature normally remains above 90°C. The temperature in the MDF day tank
should be in the range 20...40°C. The level of the tank must ensure a positive static pressure
on the suction side of the fuel feed pumps.
If black-out starting with MDF from a gravity tank is foreseen, then the tank must be located
at least 15 m above the engine crankshaft.
6.3.4.3 Starting tank, MDF (1T09)

The starting tank is needed when the engine is equipped with the engine driven fuel feed pump
and when the MDF day tank (1T06) cannot be located high enough, i.e. less than 1.5 meters
above the engine crankshaft.
The purpose of the starting tank is to ensure that fuel oil is supplied to the engine during
starting. The starting tank shall be located at least 1.5 meters above the engine crankshaft.
The volume of the starting tank should be approx. 60 l.
6.3.4.4 Leak fuel tank, clean fuel (1T04)

Clean leak fuel is drained by gravity from the engine. The fuel should be collected in a separate
clean leak fuel tank, from where it can be pumped to the day tank and reused without
separation. The pipes from the engine to the clean leak fuel tank should be arranged continuosly
sloping. The tank and the pipes must be heated and insulated, unless the installation is designed
for operation on MDF only.
The leak fuel piping should be fully closed to prevent dirt from entering the system.
6.3.4.5 Leak fuel tank, dirty fuel (1T07)

In normal operation no fuel should leak out from the components of the fuel system. In
connection with maintenance, or due to unforeseen leaks, fuel or water may spill in the hot
box of the engine. The spilled liquids are collected and drained by gravity from the engine
through the dirty fuel connection.
Dirty leak fuel shall be led to a sludge tank. The tank and the pipes must be heated and
insulated, unless the installation is designed for operation exclusively on MDF.
6-20 DAAB605808
6.3.4.6 Bunker tank (1T01)

In case intention is to operate on low sulphur fuel it is beneficial to install extra bunker tanks.
This to permit the ship to bunker low sulphur fuel in empty tanks anytime, even if both fuel
qualities are available in other tanks.
6.3.5 Fuel treatment

6.3.5.1 Separation
Heavy fuel (residual, and mixtures of residuals and distillates) must be cleaned in an efficient
centrifugal separator before it is transferred to the day tank.
Classification rules require the separator arrangement to be redundant so that required capacity
is maintained with any one unit out of operation.
All recommendations from the separator manufacturer must be closely followed.
Centrifugal disc stack separators are recommended also for installations operating on MDF
only, to remove water and possible contaminants. The capacity of MDF separators should be
sufficient to ensure the fuel supply at maximum fuel consumption. Would a centrifugal separator
be considered too expensive for a MDF installation, then it can be accepted to use coalescing
type filters instead. A coalescing filter is usually installed on the suction side of the circulation
pump in the fuel feed system. The filter must have a low pressure drop to avoid pump cavitation.
Separator mode of operation

The best separation efficiency is achieved when also the stand-by separator is in operation
all the time, and the throughput is reduced according to actual consumption.
Separators with monitoring of cleaned fuel (without gravity disc) operating on a continuous
basis can handle fuels with densities exceeding 991 kg/m3 at 15°C. In this case the main and
stand-by separators should be run in parallel.
When separators with gravity disc are used, then each stand-by separator should be operated
in series with another separator, so that the first separator acts as a purifier and the second
as clarifier. This arrangement can be used for fuels with a density of max. 991 kg/m3 at 15°C.
The separators must be of the same size.
Separation efficiency
The term Certified Flow Rate (CFR) has been introduced to express the performance of
separators according to a common standard. CFR is defined as the flow rate in l/h, 30 minutes
after sludge discharge, at which the separation efficiency of the separator is 85%, when using
defined test oils and test particles. CFR is defined for equivalent fuel oil viscosities of 380 cSt
and 700 cSt at 50°C. More information can be found in the CEN (European Committee for
Standardisation) document CWA 15375:2005 (E).
The separation efficiency is measure of the separator's capability to remove specified test
particles. The separation efficiency is defined as follows:
where:
n = separation efficiency [%]
Cout = number of test particles in cleaned test oil
Cin = number of test particles in test oil before separator
DAAB605808 6-21
6.3.5.2 Separator unit (1N02/1N05)

Separators are usually supplied as pre-assembled units designed by the separator
manufacturer.
Typically separator modules are equipped with:
● Suction strainer (1F02)
● Feed pump (1P02)
● Pre-heater (1E01)
● Sludge tank (1T05)
● Separator (1S01/1S02)
● Sludge pump
● Control cabinets including motor starters and monitoring
Fig 6-4 Fuel transfer and separating system (V76F6626G)
6-22 DAAB605808
6.3.5.3 Separator feed pumps (1P02)

Feed pumps should be dimensioned for the actual fuel quality and recommended throughput
of the separator. The pump should be protected by a suction strainer (mesh size about 0.5
mm)
An approved system for control of the fuel feed rate to the separator is required.
Design data: HFO MDF
Design pressure 0.5 MPa (5 bar) 0.5 MPa (5 bar)
Design temperature 100°C 50°C
Viscosity for dimensioning electric motor 1000 cSt 100 cSt
6.3.5.4 Separator pre-heater (1E01)

The pre-heater is dimensioned according to the feed pump capacity and a given settling tank
temperature.
The surface temperature in the heater must not be too high in order to avoid cracking of the
fuel. The temperature control must be able to maintain the fuel temperature within ± 2°C.
Recommended fuel temperature after the heater depends on the viscosity, but it is typically
98°C for HFO and 20...40°C for MDF. The optimum operating temperature is defined by the
sperarator manufacturer.
The required minimum capacity of the heater is:
where:
P = heater capacity [kW]
Q = capacity of the separator feed pump [l/h]
ΔT = temperature rise in heater [°C]
For heavy fuels ΔT = 48°C can be used, i.e. a settling tank temperature of 50°C. Fuels having
a viscosity higher than 5 cSt at 50°C require pre-heating before the separator.
The heaters to be provided with safety valves and drain pipes to a leakage tank (so that the
possible leakage can be detected).
6.3.5.5 Separator (1S01/1S02)

Based on a separation time of 23 or 23.5 h/day, the service throughput Q [l/h] of the separator
can be estimated with the formula:
where:
P = max. continuous rating of the diesel engine(s) [kW]
b = specific fuel consumption + 15% safety margin [g/kWh]
ρ = density of the fuel [kg/m3]
DAAB605808 6-23
t = daily separating time for self cleaning separator [h] (usually = 23 h or 23.5 h)
The flow rates recommended for the separator and the grade of fuel must not be exceeded.
The lower the flow rate the better the separation efficiency.
Sample valves must be placed before and after the separator.
6.3.5.6 MDF separator in HFO installations (1S02)

A separator for MDF is recommended also for installations operating primarily on HFO. The
MDF separator can be a smaller size dedicated MDF separator, or a stand-by HFO separator
used for MDF.
6.3.5.7 Sludge tank (1T05)

The sludge tank should be located directly beneath the separators, or as close as possible
below the separators, unless it is integrated in the separator unit. The sludge pipe must be
continuously falling.
6-24 DAAB605808
6.3.6 Fuel feed system - MDF installations
Fig 6-5 Fuel feed system, single main engine (DAAE003608E)
101 Fuel inlet OD28
1043 Leak fuel drain, dirty fuel FW-end OD18
105 Fuel stand-by connection OD22
DAAB605808 6-25
Fig 6-6 Fuel feed system, multiple engines (DAAF064961A)
101 Fuel inlet OD28
105 Fuel stand-by connection PLUG
6-26 DAAB605808
If the engines are to be operated on MDF only, heating of the fuel is normally not necessary.
In such case it is sufficient to install the equipment listed below. Some of the equipment listed
below is also to be installed in the MDF part of a HFO fuel oil system.
6.3.6.1 Circulation pump, MDF (1P03)

The circulation pump maintains the pressure at the injection pumps and circulates the fuel in
the system. It is recommended to use a screw pump as circulation pump. A suction strainer
with a fineness of 0.5 mm should be installed before each pump. There must be a positive
static pressure of about 30 kPa on the suction side of the pump.
Design data:
Capacity 5 x the total consumption of the connected engines
Design pressure 1.6 MPa (16 bar)
Max. total pressure (safety valve) 1.0 MPa (10 bar)
Nominal pressure see chapter "Technical Data"
Design temperature 50°C
Viscosity for dimensioning of electric 90 cSt

motor
6.3.6.2 Stand-by pump, MDF (1P08)

The stand-by pump is required in case of a single main engine equipped with an engine driven
pump. It is recommended to use a screw pump as stand-by pump. The pump should be
placed so that a positive static pressure of about 30 kPa is obtained on the suction side of
the pump.
Design data:
Capacity 5 x the total consumption of the connected engine
Viscosity for dimensioning of electric 90 cSt

motor
6.3.6.3 Flow meter, MDF (1I03)

If the return fuel from the engine is conducted to a return fuel tank instead of the day tank,
one consumption meter is sufficient for monitoring of the fuel consumption, provided that the
meter is installed in the feed line from the day tank (before the return fuel tank). A fuel oil cooler
is usually required with a return fuel tank.
The total resistance of the flow meter and the suction strainer must be small enough to ensure
a positive static pressure of about 30 kPa on the suction side of the circulation pump.
There should be a by-pass line around the consumption meter, which opens automatically in
case of excessive pressure drop.
6.3.6.4 Fine filter, MDF (1F05)

The fuel oil fine filter is a full flow duplex type filter with steel net. This filter must be installed
as near the engine as possible.
DAAB605808 6-27
The diameter of the pipe between the fine filter and the engine should be the same as the
diameter before the filters.
Design data:
Fuel viscosity according to fuel specifications
Design flow Larger than feed/circulation pump capacity
Fineness 25 μm (absolute mesh size)
Maximum permitted pressure drops at 14 cSt:
- clean filter 20 kPa (0.2 bar)
- alarm 80 kPa (0.8 bar)
6.3.6.5 Pressure control valve, MDF (1V02)

The pressure control valve is installed when the installation includes a feeder/booster unit for
HFO and there is a return line from the engine to the MDF day tank. The purpose of the valve
is to increase the pressure in the return line so that the required pressure at the engine is
achieved.
Design data:
Capacity Equal to circulation pump
Set point 0.4...0.7 MPa (4...7 bar)
6.3.6.6 MDF cooler (1E04)

The fuel viscosity may not drop below the minimum value stated in Technical data. When
operating on MDF, the practical consequence is that the fuel oil inlet temperature must be
kept below 45°C. Very light fuel grades may require even lower temperature.
Sustained operation on MDF usually requires a fuel oil cooler. The cooler is to be installed in
the return line after the engine(s). LT-water is normally used as cooling medium.
If MDF viscosity in day tank drops below stated minimum viscosity limit then it is recommended
to install an MDF cooler into the engine fuel supply line in order to have reliable viscosity
control.
Design data:
Heat to be dissipated 1 kW/cyl
Max. pressure drop, fuel oil 80 kPa (0.8 bar)
Max. pressure drop, water 60 kPa (0.6 bar)
Margin (heat rate, fouling) min. 15%
Design temperature MDF/HFO installa- 50/150°C

tion
6-28 DAAB605808
6.3.6.7 Return fuel tank (1T13)

The return fuel tank shall be equipped with a vent valve needed for the vent pipe to the MDF
day tank. The volume of the return fuel tank should be at least 100 l.
6.3.6.8 Black out start

Diesel generators serving as the main source of electrical power must be able to resume their
operation in a black out situation by means of stored energy. Depending on system design
and classification regulations, it may in some cases be permissible to use the emergency
generator. HFO engines without engine driven fuel feed pump can reach sufficient fuel pressure
to enable black out start by means of:
● A gravity tank located min. 15 m above the crankshaft
● A pneumatically driven fuel feed pump (1P11)
● An electrically driven fuel feed pump (1P11) powered by an emergency power source
DAAB605808 6-29
6.3.7 Fuel feed system - HFO installations
Fig 6-7 Fuel oil system (HFO), single main engine (DAAF437836)
System components
1E02 Heater (booster unit) 1P06 Circulation pump (booster unit)
1E03 Cooler (booster unit) 1T03 Day tank (HFO)
1E04 Cooler (MDF) 1T06 Day tank (MDF)
1F03 Safety filter (HFO) 1T08 De-aeration tank (booster unit)
1F06 Suction filter (booster unit) 1V01 Change over valve
1F08 Automatic filter (booster unit) 1V03 Pressure control valve (booster unit)
1I01 Flow meter (booster unit) 1V10 Quick closing valve (fuel oil tank)
1I02 Viscosity meter (booster unit)
1P04 Fuel feed pump (booster unit)
101 Fuel inlet OD18
6-30 DAAB605808
Fig 6-8 Example of fuel oil system (HFO), multiple engine installation (V76F6656H)
System components
1E02 Heater (booster unit) 1P06 Circulation pump (booster unit)
1E03 Cooler (booster unit) 1T03 Day tank (HFO)
1E04 Cooler (MDF) 1T06 Day tank (MDF)
1F03 Safety filter (HFO) 1T08 De-aeration tank (booster unit)
1F05 Fine filter (MDF) 1V01 Change over valve
1F06 Suction filter (booster unit) 1V02 Pressure control valve (MDF)
1F07 Suction strainer (MDF) 1V03 Pressure control valve (booster unit)
1F08 Automatic filter (booster unit) 1V04 Pressure control valve (HFO)
1I01 Flow meter (booster unit) 1V05 Overflow valve (HFO/MDF)
1I02 Viscosity meter (booster unit) 1V05-1 Overflow valve (HFO/MDF)
1N01 Feeder/Booster unit 1V07 Venting valve (booster unit)
1P03 Circulation pump (MDF) 1V08 Change over valve
1P04 Fuel feed pump (booster unit)
101 Fuel inlet OD18
DAAB605808 6-31
HFO pipes shall be properly insulated. If the viscosity of the fuel is 180 cSt/50°C or higher,
the pipes must be equipped with trace heating. It shall be possible to shut off the heating of
the pipes when operating on MDF (trace heating to be grouped logically).
6.3.7.1 Starting and stopping

The engine can be started and stopped on HFO provided that the engine and the fuel system
are pre-heated to operating temperature. The fuel must be continuously circulated also through
a stopped engine in order to maintain the operating temperature. Changeover to MDF for start
and stop is not required.
Prior to overhaul or shutdown of the external system the engine fuel system shall be flushed
and filled with MDF.
6.3.7.2 Changeover from HFO to MDF

The control sequence and the equipment for changing fuel during operation must ensure a
smooth change in fuel temperature and viscosity. When MDF is fed through the HFO
feeder/booster unit, the volume in the system is sufficient to ensure a reasonably smooth
transfer.
When there are separate circulating pumps for MDF, then the fuel change should be performed
with the HFO feeder/booster unit before switching over to the MDF circulating pumps. As
mentioned earlier, sustained operation on MDF usually requires a fuel oil cooler. The viscosity
at the engine shall not drop below the minimum limit stated in chapter Technical data.
6.3.7.3 Changeover to low sulphur fuel

● Fuel system should allow slow, controlled change in fuel temperature in order to avoid
thermal shock in the injection pumps. The recommended fuel temperature change over
rate at switching is maximum 2 °C / min.
● Check compatibility when using mixed fuels (clogging filters, separators etc). Wärtsilä
4-stroke engines are normally not sensitive for fuel lubricity and additives are not necessarily
needed.
● HFO engines starting to alternate between HFO and MDF or LSMDF can typically continue
with the same lubricant as before. Nimonic exhaust valves should be used to avoid hot
corrosion.
● HFO engines starting to operate continuously on LSHFO can continue using lubricating oil
with a BN of at least 30.
● Engines starting to operate continuously on MDF or LSMDF are recommended to start
using lubricating oil with lower BN 10-20. Exhaust valves with stellite facing should be
used.
● BN monitoring of lubricating oil should be established in order to prevent operating with
too low BN (increased risk for corrosion).
6.3.7.4 Number of engines in the same system

When the fuel feed unit serves Wärtsilä 20 engines only, maximum three engines should be
connected to the same fuel feed circuit, unless individual circulating pumps before each engine
are installed.
Main engines and auxiliary engines should preferably have separate fuel feed units. Individual
circulating pumps or other special arrangements are often required to have main engines and
auxiliary engines in the same fuel feed circuit. Regardless of special arrangements it is not
recommended to supply more than maximum two main engines and two auxiliary engines, or
one main engine and three auxiliary engines from the same fuel feed unit.
6-32 DAAB605808
In addition the following guidelines apply:

● Twin screw vessels with two engines should have a separate fuel feed circuit for each
propeller shaft.
● Twin screw vessels with four engines should have the engines on the same shaft connected
to different fuel feed circuits. One engine from each shaft can be connected to the same
circuit.
6.3.7.5 Feeder/booster unit (1N01)

A completely assembled feeder/booster unit can be supplied. This unit comprises the following
equipment:
● Two suction strainers
● Two fuel feed pumps of screw type, equipped with built-on safety valves and electric motors
● One pressure control/overflow valve
● One pressurized de-aeration tank, equipped with a level switch operated vent valve
● Two circulating pumps, same type as the fuel feed pumps
● Two heaters, steam, electric or thermal oil (one heater in operation, the other as spare)
● One automatic back-flushing filter with by-pass filter
● One viscosimeter for control of the heaters
● One control valve for steam or thermal oil heaters, a control cabinet for electric heaters
● One temperature sensor for emergency control of the heaters
● One control cabinet including starters for pumps
● One alarm panel
The above equipment is built on a steel frame, which can be welded or bolted to its foundation
in the ship. The unit has all internal wiring and piping fully assembled. All HFO pipes are
insulated and provided with trace heating.
DAAB605808 6-33
Fig 6-9 Feeder/booster unit, example (DAAE006659)
Fuel feed pump, booster unit (1P04)

The feed pump maintains the pressure in the fuel feed system. It is recommended to use a
screw pump as feed pump. The capacity of the feed pump must be sufficient to prevent
pressure drop during flushing of the automatic filter.
A suction strainer with a fineness of 0.5 mm should be installed before each pump. There
must be a positive static pressure of about 30 kPa on the suction side of the pump.
Design data:
Total consumption of the connected engines added with
Capacity the flush quantity of the automatic filter (1F08) and 15%
margin.
Viscosity for dimensioning of electric motor 1000 cSt
6-34 DAAB605808
Pressure control valve, booster unit (1V03)

The pressure control valve in the feeder/booster unit maintains the pressure in the de-aeration
tank by directing the surplus flow to the suction side of the feed pump.
Design data:
Capacity Equal to feed pump
Set-point 0.3...0.5 MPa (3...5 bar)
Automatic filter, booster unit (1F08)

It is recommended to select an automatic filter with a manually cleaned filter in the bypass
line. The automatic filter must be installed before the heater, between the feed pump and the
de-aeration tank, and it should be equipped with a heating jacket. Overheating (temperature
exceeding 100°C) is however to be prevented, and it must be possible to switch off the heating
for operation on MDF.
Design data:
Fuel viscosity According to fuel specification
Preheating If fuel viscosity is higher than 25 cSt/100°C
Design flow Equal to feed pump capacity
Fineness:
35 μm absolute
- automatic filter
(ß50 = 75, ß35 = 2, ISO 16889)
35 μm absolute
- by-pass filter
(ß50 = 75, ß35 = 2, ISO 16889)
Flow meter, booster unit (1I01)

If a fuel consumption meter is required, it should be fitted between the feed pumps and the
de-aeration tank. When it is desired to monitor the fuel consumption of individual engines in
a multiple engine installation, two flow meters per engine are to be installed: one in the feed
line and one in the return line of each engine.
There should be a by-pass line around the consumption meter, which opens automatically in
case of excessive pressure drop.
If the consumption meter is provided with a prefilter, an alarm for high pressure difference
across the filter is recommended.
DAAB605808 6-35
De-aeration tank, booster unit (1T08)

It shall be equipped with a low level alarm switch and a vent valve. The vent pipe should, if
possible, be led downwards, e.g. to the overflow tank. The tank must be insulated and equipped
with a heating coil. The volume of the tank should be at least 100 l.
Circulation pump, booster unit (1P06)

The purpose of this pump is to circulate the fuel in the system and to maintain the required
pressure at the injection pumps, which is stated in the chapter Technical data. By circulating
the fuel in the system it also maintains correct viscosity, and keeps the piping and the injection
pumps at operating temperature.
Design data:
Capacity 5 x the total consumption of the connected engines
Viscosity for dimensioning of electric motor 500 cSt
Heater, booster unit (1E02)

The heater must be able to maintain a fuel viscosity of 14 cSt at maximum fuel consumption,
with fuel of the specified grade and a given day tank temperature (required viscosity at injection
pumps stated in Technical data). When operating on high viscosity fuels, the fuel temperature
at the engine inlet may not exceed 135°C however.
The power of the heater is to be controlled by a viscosimeter. The set-point of the viscosimeter
shall be somewhat lower than the required viscosity at the injection pumps to compensate
for heat losses in the pipes. A thermostat should be fitted as a backup to the viscosity control.
To avoid cracking of the fuel the surface temperature in the heater must not be too high. The
heat transfer rate in relation to the surface area must not exceed 1.5 W/cm2.
The required heater capacity can be estimated with the following formula:
where:
P = heater capacity (kW)
Q = total fuel consumption at full output + 15% margin [l/h]
ΔT = temperature rise in heater [°C]
Viscosimeter, booster unit (1I02)

The heater is to be controlled by a viscosimeter. The viscosimeter should be of a design that
can withstand the pressure peaks caused by the injection pumps of the diesel engine.
Design data:
Operating range 0...50 cSt
Design pressure 4 MPa (40 bar)
6-36 DAAB605808
6.3.7.6 Safety filter (1F03)

The safety filter is a full flow duplex type filter with steel net. This safety filter must be installed
as close as possible to the engines. The safety filter should be equipped with a heating jacket.
In multiple engine installations it is possible to have a one common safety filter for all engines.
The diameter of the pipe between the safety filter and the engine should be the same as
between the feeder/booster unit and the safety filter.
Design data:
Fuel viscosity according to fuel specification
Design flow Equal to circulation pump capacity
Fineness 37 μm (absolute mesh size)
6.3.7.7 Overflow valve, HFO (1V05)

When several engines are connected to the same feeder/booster unit an overflow valve is
needed between the feed line and the return line. The overflow valve limits the maximum
pressure in the feed line, when the fuel lines to a parallel engine are closed for maintenance
purposes.
The overflow valve should be dimensioned to secure a stable pressure over the whole operating
range.
Design data:
Capacity Equal to circulation pump (1P06)
Set-point (Δp) 0.1...0.2 MPa (1...2 bar)
6.3.7.8 Pressure control valve (1V04)

The pressure control valve increases the pressure in the return line so that the required pressure
at the engine is achieved. This valve is needed in installations where the engine is equipped
with an adjustable throttle valve in the return fuel line of the engine.
The adjustment of the adjustable throttle valve on the engine should be carried out after the
pressure control valve (1V04) has been adjusted. The adjustment must be tested in different
loading situations including the cases with one or more of the engines being in stand-by mode.
If the main engine is connected to the same feeder/booster unit the circulation/temperatures
must also be checked with and without the main engine being in operation.
DAAB605808 6-37
6.3.8 Flushing
The external piping system must be thoroughly flushed before the engines are connected and
fuel is circulated through the engines. The piping system must have provisions for installation
of a temporary flushing filter.
The fuel pipes at the engine (connections 101 and 102) are disconnected and the supply and
return lines are connected with a temporary pipe or hose on the installation side. All filter
inserts are removed, except in the flushing filter of course. The automatic filter and the
viscosimeter should be bypassed to prevent damage. The fineness of the flushing filter should
be 6 μm or finer.
6-38 DAAB605808
Wärtsilä 20 Product Guide 7. Lubricating Oil System
7. Lubricating Oil System
7.1 Lubricating oil requirements

7.1.1 Engine lubricating oil
The lubricating oil must be of viscosity class SAE 40 and have a viscosity index (VI) of minimum
95. The lubricating oil alkalinity (BN) is tied to the fuel grade, as shown in the table below. BN
is an abbreviation of Base Number. The value indicates milligrams KOH per gram of oil.
Table 7-1 Fuel standards and lubricating oil requirements
Fuel S content,
Category Fuel standard Lubricating oil BN
[% m/m]
ASTM D 975-01, GRADE NO. 1-D, 2-D, 4-D

BS MA 100: 1996 DMX, DMA, DMB
A 10...30 < 0.4
CIMAC 2003 DX, DA, DB
ISO 8217:2017(E) ISO-F-DMX - DMB
ASTM D 975-01 GRADE NO. 1-D, 2-D, 4-D

BS MA 100: 1996 DMX, DMA, DMB
B 15...30 0.4 - 2.0
CIMAC 2003 DX, DA, DB
ISO 8217:2017(E) ISO-F-DMB
ASTM D 975-01, GRADE NO. 4-D

ASTM D 396-04, GRADE NO. 5-6
C BS MA 100: 1996 DMC, RMA10-RMK55 30...55 ≤ 4.5
CIMAC 2003 DC, A30-K700
ISO 8217:2017(E) RMA 10-RMK 700
F LIQUID BIO FUEL (LBF) 10...20 ≤ 0.05
BN 50-55 lubricants are to be selected in the first place for operation on HFO. BN 40 lubricants
can also be used with HFO provided that the sulphur content of the fuel is relatively low, and
the BN remains above the condemning limit for acceptable oil change intervals. BN 30
lubricating oils should be used together with HFO only in special cases; for example in SCR
(Selective Catalyctic Reduction) installations, if better total economy can be achieved despite
shorter oil change intervals. Lower BN may have a positive influence on the lifetime of the
SCR catalyst.
Different oil brands may not be blended, unless it is approved by the oil suppliers. Blending
of different oils must also be validated by Wärtsilä, if the engine is still under warranty.
An updated list of validated lubricating oils is supplied for every installation. Please refer to
Service Bulletin WS15S475.
7.1.2 Oil in speed governor or actuator

An oil of viscosity class SAE 30 or SAE 40 is acceptable in normal operating conditions. Usually
the same oil as in the engine can be used. At low ambient temperatures it may be necessary
to use a multigrade oil (e.g. SAE 5W-40) to ensure proper operation during start-up with cold
oil.
DAAB605808 7-1
7. Lubricating Oil System Wärtsilä 20 Product Guide
7.2 Internal lubricating oil system
Fig 7-1 Internal lubricating oil system (DAAF382589E) - UNIC C1
Table 7-2
System components:
01 Lubricating oil main pump 07 Pressure control valve
02 Prelubricating oil pump (M201) 08 Turbocharger
03 Lubricating oil cooler 09 Guide block for VIC
04 Thermostatic valve 10 ON/OFF Control valve for VIC CV381
05 Automatic filter 11 Lube oil nozzle for gearwheel lubrication (flywheel end)
06 Centrifugal filter 12 Lube oil nozzle for gearwheel lubrication (free end)
13 Crankcase vent pipe
PT201 Lubricating oil pressure, engine inlet TE201 Lubricating oil temp., engine inlet
PTZ201 Lubricating oil pressure, engine inlet ***TI201 Lubricating oil temp., engine inlet (optional)
CV656 Airwaste gate control CV381 VIC control valve
PT291A Control oil pressure after VIC valve LS204 Lubricating oil low level, wet sump
PDS/I243 Lube oil filter pressure difference *LS205 Lubricating oil high level, wet sump
Pipe connections: Size
213 Lubricating oil from separator and filling DN32
**214 Lubricating oil to separator and drain DN32
215 Lube oil filling M48*2
*221 Lube oil overflow TBA
245 Priming pump lubrication drain TBA
701 Crankcase air vent DN65
XA Crankcase oil mist drain TBA
7-2 DAAB605808
Fig 7-2 Internal lubricating oil system (TC in free end - DAAF395501E) - UNIC C2 &
UNIC 2.0
Fig 7-3 Internal lubricating oil system (TC in flywheel end - DAAF395506E) - UNIC
C2 & UNIC 2.0
Table 7-3
System components:
01 Lubricating oil main pump 07 Pressure control valve
02 Prelubricating oil pump (M201) 08 Turbocharger
03 Lubricating oil cooler 09 Guide block for VIC
04 Thermostatic valve 10 ON/OFF Control valve for VIC CV381
05 Automatic filter 11 Lube oil nozzle for gearwheel lubrication (flywheel end)
06 Centrifugal filter 12 Lube oil nozzle for gearwheel lubrication (free end)
13 Crankcase vent pipe
PT201 Lubricating oil pressure, engine inlet TE201 Lubricating oil temp., engine inlet
PTZ201 Lubricating oil pressure, engine inlet ***TI201 Lubricating oil temp., engine inlet (if ME)
DAAB605808 7-3
CV656 Airwaste gate control CV381 VIC control valve
PT241 Lube oil pressure, filter inlet **TE272 Lubricating oil temp., TC outlet (if ME)
**PT271 Lubricating oil pressure, TC inlet (if ME) TE70# Main bearing temperature
PT291A Control oil pressure after VIC valve LS204 Lubricating oil low level, wet sump
PDY243 Lube oil filter pressure difference *PT210 Lubricating oil pressure, stand-by pump
****PS210 Lube oil stand-by pump start
Pipe connections: Size
202 Lubricating oil outlet (from oil sump) DN100
203 Lubricating oil to engine driven pump DN100
205 Lubricating oil to priming pump DN32
*207 Lubricating oil to electric driven pump DN100
*208 Lubricating oil from electric driven pump DN80
213 Lubricating oil from separator and filling DN32
214 Lubricating oil to separator and drain DN32
215 Lube oil filling M48*2
245 Priming pump lubrication drain TBA
701 Crankcase air vent DN65
XA Crankcase oil mist drain TBA
7-4 DAAB605808
Fig 7-4 Flange for connections 202, 203, dry sump (V32A0506C)
The lubricating oil sump is of wet sump type for auxiliary and diesel-electric engines. Dry sump
is recommended for main engines operating on HFO. The dry sump type has two oil outlets
at each end of the engine. Two of the outlets shall be connected to the system oil tank.
The direct driven lubricating oil pump is of gear type and equipped with a pressure control
valve. The pump is dimensioned to provide sufficient flow even at low speeds. A stand-by
pump connection is available as option. Concerning suction height, flow rate and pressure of
the pump, see Technical data.
The pre-lubricating pump is an electric motor driven gear pump equipped with a safety valve.
The pump should always be running, when the engine is stopped. Concerning suction height,
flow rate and pressure of the pump, see Technical data.
The lubricating oil module built on the engine consists of the lubricating oil cooler, thermostatic
valve and automatic filter.
The centrifugal filter is installed to clean the back-flushing oil from the automatic filter.
DAAB605808 7-5
7.3 External lubricating oil system
Fig 7-5 Lubricating oil system, auxiliary engines (V76E4590F)
System components Pipe connections Size
2E02 Heater (Separator unit) 213 Lubricating oil from separator and filling DN32
2F03 Suction filter (Separator unit) 214 Lubricating oil to separator and drain DN32
2N01 Separator unit 215 Lubricating oil filling M48*2
2P03 Separator pump (Separator unit) 245 Priming pump lubrication drain M12
2S01 Separator 701 Crankcase air vent DN65
2S02 Condensate trap
2T03 New oil tank
2T04 Renovating oil tank
2T05 Renovated oil tank
2T06 Sludge tank
7-6 DAAB605808
Fig 7-6 Lubricating oil system, single main engine (V76E4591H)
2E02 Heater (Separator unit) 202 Lubricating oil outlet (from oil sump) DN100
2F01 Suction strainer (Main lubricating oil pump) 203 Lubricating oil to engine driven pump DN100
2F03 Suction filter (Separator unit) 205 Lubricating oil to priming pump DN32
2F04 Suction strainer (Prelubricating oil pump) 208 Lubricating oil from electric driven pump DN80
2F06 Suction strainer (Stand-by pump) 245 Priming pump lubrication drain M12
2N01 Separator unit 701 Crankcase air vent DN65
2P03 Separator pump (Separator unit)
2P04 Stand-by pump
DAAB605808 7-7
2S01 Separator
2S02 Condensate trap
2T01 System oil tank
2T06 Sludge tank
2V03 Pressure control valve
7-8 DAAB605808
7.3.1 Separation system

7.3.1.1 Separator unit (2N01)
Each engine must have a dedicated lubricating oil separator and the separators shall be
dimensioned for continuous separating. If the installation is designed to operate on MDF only,
then intermittent separating might be sufficient.
Generating sets operating on a fuel having a viscosity of max. 380 cSt / 50°C may have a
common lubricating oil separator unit. Three engines may have a common lubricating oil
separator unit. In installations with four or more engines two lubricating oil separator units
should be installed.
Separators are usually supplied as pre-assembled units.
Typically lubricating oil separator units are equipped with:

● Feed pump with suction strainer and safety valve
● Preheater
● Separator
● Control cabinet
The lubricating oil separator unit may also be equipped with an intermediate sludge tank and
a sludge pump, which offers flexibility in placement of the separator since it is not necessary
to have a sludge tank directly beneath the separator.
Separator feed pump (2P03)

The feed pump must be selected to match the recommended throughput of the separator.
Normally the pump is supplied and matched to the separator by the separator manufacturer.
The lowest foreseen temperature in the system oil tank (after a long stop) must be taken into
account when dimensioning the electric motor.
Separator preheater (2E02)

The preheater is to be dimensioned according to the feed pump capacity and the temperature
in the system oil tank. When the engine is running, the temperature in the system oil tank
located in the ship's bottom is normally 65...75°C. To enable separation with a stopped engine
the heater capacity must be sufficient to maintain the required temperature without heat supply
from the engine.
Recommended oil temperature after the heater is 95°C.
It shall be considered that, while the engine is stopped in stand-by mode without LT water
circulation, the separator unit may be heating up the total amount of lubricating oil in the oil
tank to a value higher than the nominal one required at engine inlet, after lube oil cooler (see
Technical Data chapter). Higher oil temperatures at engine inlet than the nominal, may be
creating higher component wear and in worst conditions damages to the equipment and
generate alarm signal at engine start, or even a load reduction request to PMS.
The surface temperature of the heater must not exceed 150°C in order to avoid cooking of
the oil.
The heaters should be provided with safety valves and drain pipes to a leakage tank (so that
possible leakage can be detected).
Separator (2S01)
The separators should preferably be of a type with controlled discharge of the bowl to minimize
the lubricating oil losses.
The service throughput Q [l/h] of the separator can be estimated with the formula:
DAAB605808 7-9
where:
Q = volume flow [l/h]
P = engine output [kW]
n = 5 for HFO, 4 for MDF
t = operating time [h/day]: 24 for continuous separator operation, 23 for normal dimensioning
Sludge tank (2T06)

The sludge tank should be located directly beneath the separators, or as close as possible
below the separators, unless it is integrated in the separator unit. The sludge pipe must be
continuously falling.
7.3.1.2 Renovating oil tank (2T04)

In case of wet sump engines the oil sump content can be drained to this tank prior to separation.
7.3.1.3 Renovated oil tank (2T05)

This tank contains renovated oil ready to be used as a replacement of the oil drained for
separation.
7.3.2 System oil tank (2T01)

Recommended oil tank volume is stated in chapter Technical data.
The system oil tank is usually located beneath the engine foundation. The tank may not protrude
under the reduction gear or generator, and it must also be symmetrical in transverse direction
under the engine. The location must further be such that the lubricating oil is not cooled down
below normal operating temperature. Suction height is especially important with engine driven
lubricating oil pump. Losses in strainers etc. add to the geometric suction height. Maximum
suction ability of the pump is stated in chapter Technical data.
The pipe connection between the engine oil sump and the system oil tank must be flexible to
prevent damages due to thermal expansion. The return pipes from the engine oil sump must
end beneath the minimum oil level in the tank. Further on the return pipes must not be located
in the same corner of the tank as the suction pipe of the pump.
The suction pipe of the pump should have a trumpet shaped or conical inlet to minimise the
pressure loss. For the same reason the suction pipe shall be as short and straight as possible
and have a sufficient diameter. A pressure gauge shall be installed close to the inlet of the
lubricating oil pump. The suction pipe shall further be equipped with a non-return valve of flap
type without spring. The non-return valve is particularly important with engine driven pump
and it must be installed in such a position that self-closing is ensured.
Suction and return pipes of the separator must not be located close to each other in the tank.
The ventilation pipe from the system oil tank may not be combined with crankcase ventilation
pipes.
It must be possible to raise the oil temperature in the tank after a long stop. In cold conditions
it can be necessary to have heating coils in the oil tank in order to ensure pumpability. The
separator heater can normally be used to raise the oil temperature once the oil is pumpable.
Further heat can be transferred to the oil from the preheated engine, provided that the oil
viscosity and thus the power consumption of the pre-lubricating oil pump does not exceed
the capacity of the electric motor.
7-10 DAAB605808
Fig 7-7 Example of system oil tank arrangement (DAAE007020e)
Design data:
Oil tank volume 1.2...1.5 l/kW, see also Technical data
Oil level at service 75...80% of tank volume
Oil level alarm 60% of tank volume
7.3.3 New oil tank (2T03)

In engines with wet sump, the lubricating oil may be filled into the engine, using a hose or an
oil can, through the dedicated lubricating oil filling connection (215). Alternatively, trough the
crankcase cover or through the separator pipe. The system should be arranged so that it is
possible to measure the filled oil volume.
7.3.4 Suction strainers (2F01, 2F04, 2F06)

It is recommended to install a suction strainer before each pump to protect the pump from
damage. The suction strainer and the suction pipe must be amply dimensioned to minimize
pressure losses. The suction strainer should always be provided with alarm for high differential
pressure.
DAAB605808 7-11
Design data:
Fineness 0.5...1.0 mm
7.3.5 Lubricating oil pump, stand-by (2P04)

The stand-by lubricating oil pump is normally of screw type and should be provided with an
safety valve.
Design data:
Capacity see Technical data
Design pressure, max 0.8 MPa (8 bar)
Design temperature, max. 100°C
Lubricating oil viscosity SAE 40
Viscosity for dimensioning the electric 500 mm2/s (cSt)

motor
7.4 Crankcase ventilation system

The purpose of the crankcase ventilation is to evacuate gases from the crankcase in order to
keep the pressure in the crankcase within acceptable limits.
Each engine must have its own vent pipe into open air. The crankcase ventilation pipes may
not be combined with other ventilation pipes, e.g. vent pipes from the system oil tank.
The diameter of the pipe shall be large enough to avoid excessive back pressure. Other possible
equipment in the piping must also be designed and dimensioned to avoid excessive flow
resistance.
A condensate trap must be fitted on the vent pipe near the engine.
The connection between engine and pipe is to be flexible. It is very important that the crankcase
ventilation pipe is properly fixed to a support rigid in all directions directly after the flexible
hose from crankcase ventilation outlet, extra mass on the oil mist detector must be avoided.
There should be a fixing point on both sides of the pipe at the support. Absolutely rigid mounting
between the pipe and the support is recommended. The supporting must allow thermal
expansion and ship’s structural deflections.
Design data:
Flow see Technical data
Backpressure, max. see Technical data
Temperature 80°C
7-12 DAAB605808
The size of the ventilation pipe (D2) out

from the condensate trap should be
equal or bigger than the ventilation pipe
(D) coming from the engine.
For more information about ventilation
pipe (D) size, see the external lubricating
oil system drawing.
The max. back-pressure must also be

considered when selecting the ventilation
pipe size.
Fig 7-8 Condensate trap
(DAAE032780B)
DAAB605808 7-13
7.5 Flushing instructions

Flushing instructions in this Product Guide are for guidance only. For contracted projects,
read the specific instructions included in the installation planning instructions (IPI). The fineness
of the flushing filter and further instructions are found from installation planning instructions
(IPI).
7.5.1 Piping and equipment built on the engine

Flushing of the piping and equipment built on the engine is not required and flushing oil shall
not be pumped through the engine oil system (which is flushed and clean from the factory).
It is however acceptable to circulate the flushing oil via the engine sump if this is advantageous.
Cleanliness of the oil sump shall be verified after completed flushing.
7.5.2 External oil system

Refer to the system diagram(s) in section External lubricating oil system for location/description
of the components mentioned below.
If the engine is equipped with a wet oil sump the external oil tanks, new oil tank (2T03),
renovating oil tank (2T04) and renovated oil tank (2T05) shall be verified to be clean before
bunkering oil. Especially pipes leading from the separator unit (2N01) directly to the engine
shall be ensured to be clean for instance by disconnecting from engine and blowing with
compressed air.
If the engine is equipped with a dry oil sump the external oil tanks, new oil tank and the system
oil tank (2T01) shall be verified to be clean before bunkering oil.
Operate the separator unit continuously during the flushing (not less than 24 hours). Leave
the separator running also after the flushing procedure, this to ensure that any remaining
contaminants are removed.
If an electric motor driven stand-by pump (2P04) is installed then piping shall be flushed running
the pump circulating engine oil through a temporary external oil filter (recommended mesh 34
microns) into the engine oil sump through a hose and a crankcase door. The pump shall be
protected by a suction strainer (2F06).
Whenever possible the separator unit shall be in operation during the flushing to remove dirt.
The separator unit is to be left running also after the flushing procedure, this to ensure that
any remaining contaminants are removed.
7.5.3 Type of flushing oil

7.5.3.1 Viscosity
In order for the flushing oil to be able to remove dirt and transport it with the flow, ideal viscosity
is 10...50 cSt. The correct viscosity can be achieved by heating engine oil to about 65°C or
by using a separate flushing oil which has an ideal viscosity in ambient temperature.
7.5.3.2 Flushing with engine oil

The ideal is to use engine oil for flushing. This requires however that the separator unit is in
operation to heat the oil. Engine oil used for flushing can be reused as engine oil provided that
no debris or other contamination is present in the oil at the end of flushing.
7.5.3.3 Flushing with low viscosity flushing oil

If no separator heating is available during the flushing procedure it is possible to use a low
viscosity flushing oil instead of engine oil. In such a case the low viscosity flushing oil must
be disposed of after completed flushing. Great care must be taken to drain all flushing oil from
7-14 DAAB605808
pockets and bottom of tanks so that flushing oil remaining in the system will not compromise
the viscosity of the actual engine oil.
7.5.3.4 Lubricating oil sample

To verify the cleanliness a LO sample shall be taken by the shipyard after the flushing is
completed. The properties to be analyzed are Viscosity, BN, AN, Insolubles, Fe and Particle
Count.
Commissioning procedures shall in the meantime be continued without interruption unless
the commissioning engineer believes the oil is contaminated.
DAAB605808 7-15
Wärtsilä 20 Product Guide 8. Compressed Air System
8. Compressed Air System

Compressed air is used to start engines and to provide actuating energy for safety and control
devices. The use of starting air for other purposes is limited by the classification regulations.
To ensure the functionality of the components in the compressed air system, the compressed
air has to be free from solid particles and oil.
8.1 Internal compressed air system

The engine is equipped with a pneumatic starting motor driving the engine through a gear rim
on the flywheel.
The compressed air system of the electro-pneumatic overspeed trip is connected to the
starting air system. For this reason, the air supply to the engine must not be closed during
operation.
The nominal starting air pressure of 3 MPa (30 bar) is reduced with a pressure regulator before
the pnemautic starting motor.
Fig 8-1 Internal starting air system, WA20 (DAAF382588C) - UNIC C1
System components:
01 Turbine starter 05 Air container
02 Blocking valve, when turning gear engaged 06 Solenoid valve
03 Pneumatic cylinder at each injection pump (for overspeed) 07 Safety valve
DAAB605808 8-1
8. Compressed Air System Wärtsilä 20 Product Guide
PT301 Starting air pressure, engine inlet CV153-2 Stop/shutdown solenoid valve 2
PT311 Control air pressure CV321 Start solenoid valve
GS792 Turning gear engaged HS321 Emergency start
301 Starting air inlet OD28
Fig 8-2 Internal starting air system (DAAF395503C) - UNIC C2 & UNIC 2.0
System components:
01 Turbine starter 05 Air container
02 Blocking valve, when turning gear engaged 06 Solenoid valve (optional)
03 Pneumatic cylinder for overspeed 07 Safety valve
04 Pressure regulator 08 Charge air blocking device (optional)
PT301 Starting air pressure, engine inlet CV153-1 Stop solenoid 1
PT311 Control air pressure, engine inlet CV153-2 Stop solenoid 2
8-2 DAAB605808
GS792 Turning gear position CV321 Starting solenoid
GS621 Charge air blocking device (optional) HS321 EMERGENCY START
301 Starting air inlet, 3MPa OD28
DAAB605808 8-3
8.2 External compressed air system

The design of the starting air system is partly determined by classification regulations. Most
classification societies require that the total capacity is divided into two equally sized starting
air receivers and starting air compressors. The requirements concerning multiple engine
installations can be subject to special consideration by the classification society.
The starting air pipes should always be slightly inclined and equipped with manual or automatic
draining at the lowest points.
Fig 8-3 External starting air system (DAAE007204I)
System components
3F02 Air filter (Starting air inlet) 3P01 Compressor (Starting air compressor unit)
3N02 Starting air compressor unit 3S01 Separator (Starting air compressor unit)
301 Staring air inlet OD28
8.2.1 Starting air compressor unit (3N02)

At least two starting air compressors must be installed. It is recommended that the compressors
are capable of filling the starting air vessel from minimum (1.8 MPa) to maximum pressure in
15...30 minutes. For exact determination of the minimum capacity, the rules of the classification
societies must be followed.
8.2.2 Oil and water separator (3S01)

An oil and water separator should always be installed in the pipe between the compressor
and the air vessel. Depending on the operation conditions of the installation, an oil and water
separator may be needed in the pipe between the air vessel and the engine.
8.2.3 Starting air vessel (3T01)

The starting air vessels should be dimensioned for a nominal pressure of 3 MPa.
8-4 DAAB605808
The number and the capacity of the air vessels for propulsion engines depend on the
requirements of the classification societies and the type of installation.
It is recommended to use a minimum air pressure of 1.8 MPa, when calculating the required
volume of the vessels.
The starting air vessels are to be equipped with at least a manual valve for condensate drain.
If the air vessels are mounted horizontally, there must be an inclination of 3...5° towards the
drain valve to ensure efficient draining.
Size Dimensions [mm] Weight

[Litres] [kg]
L1 L2 1) L3 1) D
125 1807 243 110 324 170
180 1217 243 110 480 200
250 1767 243 110 480 274
500 3204 243 133 480 450
1) Dimensions are approximate.
Fig 8-4 Starting air vessel
The starting air consumption stated in technical data is for a successful start. During start the
main starting valve is kept open until the engine starts, or until the max. time for the starting
attempt has elapsed. A failed start can consume two times the air volume stated in technical
data. If the ship has a class notation for unattended machinery spaces, then the starts are to
be demonstrated.
The required total starting air vessel volume can be calculated using the formula:
where:
VR = total starting air vessel volume [m3]
pE = normal barometric pressure (NTP condition) = 0.1 MPa
VE = air consumption per start [Nm3] See Technical data
n = required number of starts according to the classification society
pRmax = maximum starting air pressure = 3 MPa
DAAB605808 8-5
pRmin = minimum starting air pressure = See Technical data
NOTE
The total vessel volume shall be divided into at least two equally sized starting air
vessels.
8.2.4 Air filter, starting air inlet (3F02)

Condense formation after the water separator (between starting air compressor and starting
air vessels) create and loosen abrasive rust from the piping, fittings and receivers. Therefore
it is recommended to install a filter before the starting air inlet on the engine to prevent particles
to enter the starting air equipment.
An Y-type strainer can be used with a stainless steel screen and mesh size 75 µm. The pressure
drop should not exceed 20 kPa (0.2 bar) for the engine specific starting air consumption under
a time span of 4 seconds.
The starting air filter is mandatory for Wärtsilä 20 engines.
8-6 DAAB605808
Wärtsilä 20 Product Guide 9. Cooling Water System
9. Cooling Water System
9.1 Water quality

The fresh water in the cooling water system of the engine must fulfil the following requirements:
p H ............................... min. 6.5...8.5
Hardness ..................... max. 10 °dH
Chlorides ..................... max. 80 mg/l
Sulphates .................... max. 150 mg/l
Good quality tap water can be used, but shore water is not always suitable. It is recommended
to use water produced by an onboard evaporator. Fresh water produced by reverse osmosis
plants often has higher chloride content than permitted. Rain water is unsuitable as cooling
water due to the high content of oxygen and carbon dioxide.
Only treated fresh water containing approved corrosion inhibitors may be circulated through
the engines. It is important that water of acceptable quality and approved corrosion inhibitors
are used directly when the system is filled after completed installation.
9.1.1 Corrosion inhibitors

The use of an approved cooling water additive is mandatory. An updated list of approved
products is supplied for every installation and it can also be found in the Instruction manual
of the engine, together with dosage and further instructions.
9.1.2 Glycol
Use of glycol in the cooling water is not recommended unless it is absolutely necessary.
Starting from 20% glycol the engine is to be de-rated 0.23 % per 1% glycol in the water. Max.
60% glycol is permitted.
Corrosion inhibitors shall be used regardless of glycol in the cooling water.
DAAB605808 9-1
9. Cooling Water System Wärtsilä 20 Product Guide
9.2 Internal cooling water system
NOTE
*Optional
T = Test plug
Fig 9-1 Internal cooling water system (DAAF382591C) - UNIC C1
System components:
01 HT-cooling water pump 05 HT-thermostatic valve
02 LT-cooling water pump 06 LT-thermostatic valve
03 Charge air cooler 07 Adjustable orifice
Sensors and Indicators:
PT401 HT water pressure, jacket inlet TI482 LT water temperature, LOC outlet
TI472 LT water temperature, CAC outlet PT471 LT water pressure, CAC inlet
TE402 HT water temperature, jacket outlet TE471 LT water temperature, CAC inlet
TE401 HT water temperature, jacket inlet TI471 LT water temperature, CAC inlet
TI401 HT water temperature, engine inlet TEZ402 HT water temperature, jacket outlet
Pipe connections Size Pressure class Standard
401 HT-water inlet DN65 PN16 ISO 7005-1
402 HT-water outlet DN65 PN16 ISO 7005-1
404 HT-water air vent OD12 PN250 DIN 2353
406 Water from preheater to HT-circuit DN65 or PN16 or ISO 7005-1 or

OD28 PN250 DIN 2353
411 HT-water drain M10 x 1 - Plug
451 LT-water inlet DN80 PN16 ISO 7005-1
452 LT-water outlet DN80 PN16 ISO 7005-1
454 LT-water air vent from air cooler OD12 PN250 DIN 2353
460 LT-water from generator TBA TBA TBA
9-2 DAAB605808
461 LT-water to generator TBA TBA TBA
464 LT-water drain M18 x 1.5 - Plug
Fig 9-2 Internal cooling water system (DAAF395504E) - UNIC C2 & UNIC 2.0
System components:
01 HT-cooling water pump 05 HT-thermostatic valve
02 LT-cooling water pump ****06 LT-thermostatic valve
03 Charge air cooler 07 Adjustable orifice
04 Lubricating oil cooler 08 Sea water pump (option)
Sensors and Indicators:
PT401 HT water pressure, jacket inlet ***TI482 LT water temperature, LOC outlet
*PT410 HT water pressure, stand-by pump PT471 LT water pressure, CAC inlet
*PT460 LT water pressure, stand-by pump TE471 LT water temperature, CAC inlet
TE401 HT water temperature, jacket inlet ***TI471 LT water temperature, CAC inlet
***TI401 HT water temperature, jacket inlet TEZ402 HT water temperature, jacket outlet
TE402 HT water temperature, jacket outlet ***TI472 LT water temperature, CAC outlet
*****PS410 HT water stand-by pump start *****PS460 LT water stand-by pump start
******TEZ402- HT water temperature, jacket outlet

1
401 HT-water inlet DN65 PN16 ISO 7005-1
402 HT-water outlet DN65 PN16 ISO 7005-1
404 HT-water air vent OD12 PN250 DIN 2353
406 Water from preheater to HT-circuit DN65 or PN16 or ISO 7005-1 or

OD28 PN250 DIN 2353
*408 HT-water from stand-by pump DN65 PN16 ISO 7005-1
411 HT-water drain M10 x 1 - Plug
451 LT-water inlet DN80 PN16 ISO 7005-1
DAAB605808 9-3
452 LT-water outlet DN80 PN16 ISO 7005-1
454 LT-water air vent from air cooler OD12 PN250 DIN 2353
*457 LT-water from stand-by pump DN80 PN16 ISO 7005-1
464 LT-water drain M18 x 1.5 - Plug
****476 Sea water to engine driven pump (option) TBA TBA TBA
****477 Sea water from engine driven pump (option) TBA TBA TBA
The fresh water cooling system is divided into a high temperature (HT) and a low temperature
(LT) circuit. The HT water circulates through cylinder jackets and cylinder heads.
The LT water circulates through the charge air cooler and the lubricating oil cooler, which is
built on the engine.
Temperature control valves regulate the temperature of the water out from the engine, by
circulating some water back to the cooling water pump inlet. The HT temperature control valve
is always mounted on the engine, while the LT temperature control valve can be either on the
engine or separate. In installations where the engines operate on MDF only it is possible to
install the LT temperature control valve in the external system and thus control the LT water
temperature before the engine.
9.2.1 Engine driven circulating pumps

The LT and HT cooling water pumps are engine driven. The engine driven pumps are located
at the free end of the engine.
Pump curves for engine driven pumps are shown in the diagrams. The nominal pressure and
capacity can be found in the chapter Technical data.
9-4 DAAB605808
Fig 9-3 Pump curves
Table 9-1 Impeller diameters of engine driven HT & LT pumps
Engine Engine speed [rpm] HT impeller [Ø mm] LT impeller [Ø mm]

type
W 4L20 900 180 187
1000 170 170
DAAB605808 9-5
Engine Engine speed [rpm] HT impeller [Ø mm] LT impeller [Ø mm]

type
W 6L20 900 187 187
1000 175 175
1200 180 187
W 8L20 900 191 197
1000 180 187
1200 187 197
W 9L20 900 191 197
1000 180 187
1200 187 197
9.2.2 Engine driven sea water pump

An engine driven sea water pump is available for main engines:
Fig 9-4 Engine driven sea water pump curves
9-6 DAAB605808
9.3 External cooling water system

It is recommended to divide the engines into several circuits in multi-engine installations. One
reason is of course redundancy, but it is also easier to tune the individual flows in a smaller
system. Malfunction due to entrained gases, or loss of cooling water in case of large leaks
can also be limited. In some installations it can be desirable to separate the HT circuit from
the LT circuit with a heat exchanger.
The external system shall be designed so that flows, pressures and temperatures are close
to the nominal values in Technical data and the cooling water is properly de-aerated.
Pipes with galvanized inner surfaces are not allowed in the fresh water cooling system. Some
cooling water additives react with zinc, forming harmful sludge. Zinc also becomes nobler
than iron at elevated temperatures, which causes severe corrosion of engine components.
Fig 9-5 Cooling water system, HFO engines with heat recovery (DAAF068123B)
System components:
1E04 Cooler (MDF) 4P06 Circulating pump
4E03 Heat recovery (Evaporator) 4P09 Transfer pump
4E05 Heater (Preheater) 4P19 Circulating pump (Evaporator)
4E08 Central cooler 4S01 Air venting
4E15 Cooler (Generator) 4T04 Drain tank
4N01 Preheating unit 4T05 Expansion tank
4N02 Evaporator unit 4V02 Temperature control valve (Heat recovery)
4P04 Circulating pump (Preheater) 4V08 Temperature control valve (Central cooler)
Pos Pipe connections Size
401 HT-water inlet DN65
DAAB605808 9-7
Pos Pipe connections Size
402 HT-water outlet DN65
404 HT-air vent OD12
406 Water from preheater to HT-circuit OD28
451 LT-water inlet DN80
452 LT-water outlet DN80
454 LT-water air vent from air cooler OD12
460 LT-water to generator -
461 LT-water from generator -
9-8 DAAB605808
Fig 9-6 Cooling water system, auxiliary engines operating on HFO and MDO without
heat recovery (V76C5823D)
System components:
4E05 Heater (Preheater) 4S01 Air venting
4E08 Central cooler 4T04 Drain tank
4N01 Preheating unit 4T05 Expansion tank
4P04 Circulating pump (Preheater) 4V08 Temperature control valve (central cooler)
4P09 Transfer pump
Pipe connections are listed in section "Internal cooling water system".
DAAB605808 9-9
Fig 9-7 Cooling water system, single main engine (V76C5825D)
System components:
1E04 Cooler (MDF) 4P09 Transfer pump
4E08 Central cooler 4P11 Circulating pump (Sea water)
4E10 Cooler (Reduction gear) 4P12 Circulating pump
4F01 Suction strainer (Sea water) 4S01 Air venting
4N01 Preheating unit 4T04 Drain tank
4P03 Stand-by pump (HT) 4T05 Expansion tank
4P05 Stand-by pump (LT) 4V08 Temperature control valve (Central cooler)
9-10 DAAB605808
Fig 9-8 Cooling water system, MDF engines with heat recovery (V76C5827D)
System components:
1E04 Cooler (MDF) 4P09 Transfer pump
4E03 Heat recovery (Evaporator) 4P19 Circulating pump (Evaporator)
4E05 Heater (Preheater) 4S01 Air venting
4E08 Central cooler 4T04 Drain tank
4E15 Cooler (Generator) 4T05 Expansion tank
4N01 Preheating unit 4V02 Thermostatic control valve (Heat recovery)
4N02 Evaporator unit 4V08 Thermostatic control valve (Central cooler)
4P04 Circulating pump (Preheater)
DAAB605808 9-11
Ships (with ice class) designed for cold sea-water should have provisions for recirculation
back to the sea chest from the central cooler:
● For melting of ice and slush, to avoid clogging of the sea water strainer
● To enhance the temperature control of the LT water, by increasing the seawater temperature
9.3.1 Stand-by circulation pumps (4P03, 4P05)

Stand-by pumps should be of centrifugal type and electrically driven. Required capacities and
delivery pressures are stated in Technical data.
NOTE
Some classification societies require that spare pumps are carried onboard even
though the ship has multiple engines. Stand-by pumps can in such case be worth
considering also for this type of application.
9.3.2 Sea water pump (4P11)

The capacity of electrically driven sea water pumps is determined by the type of coolers and
the amount of heat to be dissipated.
Significant energy savings can be achieved in most installations with frequency control of
electrically driven sea water pumps. Minimum flow velocity (fouling) and maximum sea water
temperature (salt deposits) are however issues to consider.
9.3.3 Temperature control valve for central cooler (4V08)

When it is desired to utilize the engine driven LT-pump for cooling of external equipment, e.g.
a reduction or a generator, there must be a common LT temperature control valve in the
external system, instead of an individual valve for each engine. The common LT temperature
control valve is installed after the central cooler and controls the temperature of the water
before the engine and the external equipment, by partly bypassing the central cooler. The
valve can be either direct acting or electrically actuated.
The set-point of the temperature control valve 4V08 is 38 ºC in the type of system described
above.
Engines operating on HFO must have individual LT temperature control valves. A separate
pump is required for the external equipment in such case, and the set-point of 4V08 can be
lower than 38 ºC if necessary.
9.3.4 Fresh water central cooler (4E08)

The fresh water cooler can be of either plate, tube or box cooler type. Plate coolers are most
common. Several engines can share the same cooler.
It can be necessary to compensate a high flow resistance in the circuit with a smaller pressure
drop over the central cooler.
The flow to the fresh water cooler must be calculated case by case based on how the circuit
is designed.
In case the fresh water central cooler is used for combined LT and HT water flows in a parallel
system the total flow can be calculated with the following formula:
where:
q = total fresh water flow [m³/h]
9-12 DAAB605808
qLT = nominal LT pump capacity[m³/h]
Φ = heat dissipated to HT water [kW]
Tout = HT water temperature after engine ( 91°C)
Tin = HT water temperature after cooler (38°C)
Design data:
Fresh water flow see chapter Technical Data
Heat to be dissipated see chapter Technical Data
Pressure drop on fresh water side max. 60 kPa (0.6 bar)
Sea-water flow acc. to cooler manufacturer, normally 1.2 - 1.5 x the fresh
water flow
Pressure drop on sea-water side, norm. acc. to pump head, normally 80 - 140 kPa (0.8 - 1.4 bar)
Fresh water temperature after LT cooler max. 38 °C
Fresh water temperature after HT cooler max. 83 °C
Margin (heat rate, fouling) 15%
Fig 9-9 Central cooler, main dimensions (4V47E0188b)
Cooling water Sea water Dimension [mm] Weight [kg]
Engine [rpm] Flow Tcw, in Tcw, out Flow Tsw, in Tsw, out A B C Dry Wet
type [m³/h] [°C] [°C] [m³/h] [°C] [°C]
W4L20 1000 27 54.3 38 36 32 44.3 106 505 695 275 298
W6L20 1000 40 53.3 38 53 32 43.5 150 655 845 288 321
W8L20 1000 53 53.6 38 71 32 43.8 198 655 845 298 341
W9L20 1000 59 53.7 38 80 32 43.8 221 905 1095 305 354
DAAB605808 9-13
As an alternative for the central coolers of the plate or of the tube type a box cooler can be
installed. The principle of box cooling is very simple. Cooling water is forced through a
U-tube-bundle, which is placed in a sea-chest having inlet- and outlet-grids. Cooling effect
is reached by natural circulation of the surrounding water. The outboard water is warmed up
and rises by its lower density, thus causing a natural upward circulation flow which removes
the heat.
Box cooling has the advantage that no raw water system is needed, and box coolers are less
sensitive for fouling and therefor well suited for shallow or muddy waters.
9.3.5 Waste heat recovery

The waste heat in the HT cooling water can be used for fresh water production, central heating,
tank heating etc. The system should in such case be provided with a temperature control
valve to avoid unnecessary cooling, as shown in the example diagrams. With this arrangement
the HT water flow through the heat recovery can be increased.
The heat available from HT cooling water is affected by ambient conditions. It should also be
taken into account that the recoverable heat is reduced by circulation to the expansion tank,
radiation from piping and leakages in temperature control valves.
9.3.6 Air venting

Air may be entrained in the system after an overhaul, or a leak may continuously add air or
gas into the system. The engine is equipped with vent pipes to evacuate air from the cooling
water circuits. The vent pipes should be drawn separately to the expansion tank from each
connection on the engine.
Venting pipes to the expansion tank are to be installed at all high points in the piping system,
where air or gas can accumulate.
The vent pipes must be continuously rising.
9.3.7 Expansion tank (4T05)

The expansion tank compensates for thermal expansion of the coolant, serves for venting of
the circuits and provides a sufficient static pressure for the circulating pumps.
Design data:
Pressure from the expansion tank at pump inlet 70 - 150 kPa (0.7...1.5 bar)
Volume min. 10% of the total system volume
NOTE
The maximum pressure at the engine must not be exceeded in case an electrically
driven pump is installed significantly higher than the engine.
Concerning the water volume in the engine, see chapter Technical data.
The expansion tank should be equipped with an inspection hatch, a level gauge, a low level
alarm and necessary means for dosing of cooling water additives.
The vent pipes should enter the tank below the water level. The vent pipes must be drawn
separately to the tank (see air venting) and the pipes should be provided with labels at the
expansion tank.
The balance pipe down from the expansion tank must be dimensioned for a flow velocity not
exceeding 1.0...1.5 m/s in order to ensure the required pressure at the pump inlet with engines
9-14 DAAB605808
running. The flow through the pipe depends on the number of vent pipes to the tank and the
size of the orifices in the vent pipes. The table below can be used for guidance.
Table 9-2 Minimum diameter of balance pipe
Nominal pipe size Max. flow velocity (m/s) Max. number of vent pipes
with ø 5 mm orifice
DN 32 1.1 3
DN 40 1.2 6
DN 50 1.3 10
DN 65 1.4 17
9.3.8 Drain tank (4T04)

It is recommended to collect the cooling water with additives in a drain tank, when the system
has to be drained for maintenance work. A pump should be provided so that the cooling water
can be pumped back into the system and reused.
Concerning the water volume in the engine, see chapter Technical data. The water volume in
the LT circuit of the engine is small.
9.3.9 HT preheating
The cooling water circulating through the cylinders must be preheated to at least 60 ºC,
preferably 70 ºC. This is an absolute requirement for installations that are designed to operate
on heavy fuel, but strongly recommended also for engines that operate exclusively on marine
diesel fuel.
The energy required for preheating of the HT cooling water can be supplied by a separate
source or by a running engine, often a combination of both. In all cases a separate circulating
pump must be used. It is common to use the heat from running auxiliary engines for preheating
of main engines. In installations with several main engines the capacity of the separate heat
source can be dimensioned for preheating of two engines, provided that this is acceptable
for the operation of the ship. If the cooling water circuits are separated from each other, the
energy is transferred over a heat exchanger.
9.3.9.1 HT heater (4E05)

The energy source of the heater can be electric power, steam or thermal oil.
It is recommended to heat the HT water to a temperature near the normal operating
temperature. The heating power determines the required time to heat up the engine from cold
condition.
The minimum required heating power is 2 kW/cyl, which makes it possible to warm up the
engine from 20 ºC to 60...70 ºC in 10-15 hours. The required heating power for shorter heating
time can be estimated with the formula below. About 1 kW/cyl is required to keep a hot engine
warm.
Design data:
Preheating temperature min. 60°C for starts at LFO or gas; Min 70°C for startings at HFO
Required heating power 2 kW/cyl
Heating power to keep hot engine warm 1 kW/cyl
Required heating power to heat up the engine, see formula below:
DAAB605808 9-15
where:
P = Preheater output [kW]
T1 = Preheating temperature = 60...70 °C
T0 = Ambient temperature [°C]
meng = Engine weight [tonne]
VLO = Lubricating oil volume [m3] (wet sump engines only)
VFW = HT water volume [m3]
t = Preheating time [h]

keng = Engine specific coefficient = 0.5 kW
ncyl = Number of cylinders
The formula above should not be used for P < 2 kW/cyl
9.3.9.2 Circulation pump for HT preheater (4P04)

Design data:
Capacity 0.3 m3/h per cylinder
Delivery pressure 80...100 kPa (0.8...1.0 bar)
9.3.9.3 Preheating unit (4N01)

A complete preheating unit can be supplied. The unit comprises:
● Electric or steam heaters
● Circulating pump
● Control cabinet for heaters and pump
● Set of thermometers
● Non-return valve
● Safety valve
Fig 9-10 Preheating unit, electric (V60L0653A)
9-16 DAAB605808
Heater capacity Pump capacity Weight Pipe connections Dimensions
kW m3 /h kg Inlet / Outlet A B C D E
7.5 3 75 DN40 1050 720 610 190 425
12 3 93 DN40 1050 550 660 240 450
15 3 93 DN40 1050 720 660 240 450
18 3 95 DN40 1250 900 660 240 450
22.5 8 100 DN40 1050 720 700 290 475
27 8 103 DN40 1250 900 700 290 475
30 8 105 DN40 1050 720 700 290 475
36 8 125 DN40 1250 900 700 290 475
45 8 145 DN40 1250 720 755 350 505
54 8 150 DN40 1250 900 755 350 505
9.3.10 Throttles
Throttles (orifices) are to be installed in all by-pass lines to ensure balanced operating conditions
for temperature control valves. Throttles must also be installed wherever it is necessary to
balance the waterflow between alternate flow paths.
9.3.11 Thermometers and pressure gauges

Local thermometers should be installed wherever there is a temperature change, i.e. before
and after heat exchangers etc. in external system.
Local pressure gauges should be installed on the suction and discharge side of each pump.
DAAB605808 9-17
Wärtsilä 20 Product Guide 10. Combustion Air System
10. Combustion Air System
10.1 Engine room ventilation

To maintain acceptable operating conditions for the engines and to ensure trouble free operation
of all equipment, attention shall be paid to the engine room ventilation and the supply of
combustion air.
The air intakes to the engine room must be located and designed so that water spray, rain
water, dust and exhaust gases cannot enter the ventilation ducts and the engine room.
The dimensioning of blowers and extractors should ensure that an overpressure of about 50
Pa is maintained in the engine room in all running conditions.
For the minimum requirements concerning the engine room ventilation and more details, see
applicable standards, such as ISO 8861.
The amount of air required for ventilation is calculated from the total heat emission Φ to
evacuate. To determine Φ, all heat sources shall be considered, e.g.:
● Main and auxiliary diesel engines
● Exhaust gas piping
● Generators
● Electric appliances and lighting
● Boilers
● Steam and condensate piping
● Tanks
It is recommended to consider an outside air temperature of no less than 35°C and a
temperature rise of 11°C for the ventilation air.
The amount of air required for ventilation is then calculated using the formula:
where:
qv = air flow [m³/s]

Φ = total heat emission to be evacuated [kW]
ρ = air density 1.13 kg/m³
c = specific heat capacity of the ventilation air 1.01 kJ/kgK
ΔT = temperature rise in the engine room [°C]
The heat emitted by the engine is listed in chapter Technical data.
The engine room ventilation air has to be provided by separate ventilation fans. These fans
should preferably have two-speed electric motors (or variable speed). The ventilation can then
be reduced according to outside air temperature and heat generation in the engine room, for
example during overhaul of the main engine when it is not preheated (and therefore not heating
the room).
The ventilation air is to be equally distributed in the engine room considering air flows from
points of delivery towards the exits. This is usually done so that the funnel serves as exit for
most of the air. To avoid stagnant air, extractors can be used.
DAAB605808 10-1
10. Combustion Air System Wärtsilä 20 Product Guide
It is good practice to provide areas with significant heat sources, such as separator rooms
with their own air supply and extractors.
Under-cooling of the engine room should be avoided during all conditions (service conditions,
slow steaming and in port). Cold draft in the engine room should also be avoided, especially
in areas of frequent maintenance activities. For very cold conditions a pre-heater in the system
should be considered. Suitable media could be thermal oil or water/glycol to avoid the risk
for freezing. If steam is specified as heating medium for the ship, the pre-heater should be in
a secondary circuit.
Fig 10-1 Engine room ventilation, turbocharger with air filter (DAAE092651)
10-2 DAAB605808
Wärtsilä 20 Product Guide 10. Combustion Air System
Fig 10-2 Engine room ventilation, air duct connected to the turbocharger
(DAAE092652A)
10.2 Combustion air system design

Usually, the combustion air is taken from the engine room through a filter on the turbocharger.
This reduces the risk for too low temperatures and contamination of the combustion air. It is
important that the combustion air is free from sea water, dust, fumes, etc.
For the required amount of combustion air, see section Technical data.
The combustion air shall be supplied by separate combustion air fans, with a capacity slightly
higher than the maximum air consumption. The combustion air mass flow stated in technical
data is defined for an ambient air temperature of 25°C. Calculate with an air density
corresponding to 30°C or more when translating the mass flow into volume flow. The expression
below can be used to calculate the volume flow.
where:
qc = combustion air volume flow [m³/s]
m' = combustion air mass flow [kg/s]
ρ = air density 1.15 kg/m³
The fans should preferably have two-speed electric motors (or variable speed) for enhanced
flexibility. In addition to manual control, the fan speed can be controlled by engine load.
In multi-engine installations each main engine should preferably have its own combustion air
fan. Thus the air flow can be adapted to the number of engines in operation.
The combustion air should be delivered through a dedicated duct close to the turbocharger,
directed towards the turbocharger air intake. The outlet of the duct should be equipped with
DAAB605808 10-3
10. Combustion Air System Wärtsilä 20 Product Guide
a flap for controlling the direction and amount of air. Also other combustion air consumers,
for example other engines, gas turbines and boilers shall be served by dedicated combustion
air ducts.
If necessary, the combustion air duct can be connected directly to the turbocharger with a
flexible connection piece. With this arrangement an external filter must be installed in the duct
to protect the turbocharger and prevent fouling of the charge air cooler. The permissible total
pressure drop in the duct is max. 1.5 kPa. The duct should be provided with a step-less
change-over flap to take the air from the engine room or from outside depending on engine
load and air temperature.
For very cold conditions arctic setup is to be used. The combustion air fan is stopped during
start of the engine and the necessary combustion air is drawn from the engine room. After
start either the ventilation air supply, or the combustion air supply, or both in combination
must be able to maintain the minimum required combustion air temperature. The air supply
from the combustion air fan is to be directed away from the engine, when the intake air is cold,
so that the air is allowed to heat up in the engine room.
10.2.1 Charge air shut-off valve (optional)

In installations where it is possible that the combustion air includes combustible gas or vapour
the engines can be equipped with charge air shut-off valve. This is regulated mandatory where
ingestion of flammable gas or fume is possible.
10.2.2 Condensation in charge air coolers

Air humidity may condense in the charge air cooler, especially in tropical conditions. The
engine equipped with a small drain pipe from the charge air cooler for condensed water.
The amount of condensed water can be estimated with the diagram below.
Example, according to the diagram:

At an ambient air temperature of 35°C and a relative humidity of
80%, the content of water in the air is 0.029 kg water/ kg dry air.
If the air manifold pressure (receiver pressure) under these condi-
tions is 2.5 bar (= 3.5 bar absolute), the dew point will be 55°C.
If the air temperature in the air manifold is only 45°C, the air can
only contain 0.018 kg/kg. The difference, 0.011 kg/kg (0.029 -
0.018) will appear as condensed water.
Fig 10-3 Condensation in charge air

coolers
10-4 DAAB605808
Wärtsilä 20 Product Guide 11. Exhaust Gas System
11. Exhaust Gas System
11.1 Internal exhaust gas system
Fig 11-1 Internal exhaust gas system (DAAF382590D) - UNIC C1
System components:
01 Turbocharger
02 Water container
03 Charge air cooler
04 Adjustable charge air wastegate
TE50#1A Exhaust gas temperature after each cylinder PT601 - 2 Charge air pressure, engine inlet
TE511 Exhaust gas temperature, TC inlet CV656 Air wastegate control
TE517 Exhaust gas temperature, TC outlet *TE517 - 1 Exhaust gas temperature, TC outlet
SE518 Turbocharger speed TE601 Charge air temperature, engine inlet
PT601 Charge air pressure, engine inlet ***TI601 Charge air temperature, engine inlet (optional)
501 Exhaust gas outlet 4L: DN200

6L: DN250
8L: DN250,DN300
9L: DN300
502 Cleaning water to turbine OD15
DAAB605808 11-1
11. Exhaust Gas System Wärtsilä 20 Product Guide
Fig 11-2 Internal exhaust gas system (DAAF395505C) - UNIC C2 & UNIC 2.0
System components:
01 Turbocharger 05 Water mist separator
02 Water container 06 Adjustable charge air wastegate
03 Pressure from air duct 07 Charge air shut-off valve
04 Charge air cooler
TE50#1A Exhaust gas temperature after each cylinder TE600 Air temperature, TC inlet (if Arctic option)
TE511 Exhaust gas temperature, TC inlet CV621 Charge air shut-off valve control
TE517 Exhaust gas temperature, TC outlet GS621 Charge air shut-off valve position
SE518 TC speed TE601 Charge air temperature, engine inlet
PT601 Charge air pressure, engine inlet TI601 Charge air temperature, engine inlet (optional)
CV656 Air wastegate control
501 Exhaust gas outlet 4L: DN200

6L: DN250
8L: DN250,DN300
9L: DN300
502 Cleaning water to turbine OD15
601 Suction air inlet as same as connecting

pipe
11-2 DAAB605808
11.2 Temperature sensor location after Turbocharger

For measuring the exhaust gases after the turbocharger, the engine is delivered with
temperature sensor TE517. The sensor is located at the exhaust gas bend, which is mounted
on the turbocharger. Measuring results from this sensor is used to alarm / trigger load reduction,
if exhaust gasses are abnormal high. It is also used in exhaust gas temperature (t6) control
functionality in the SCR installations.
Fig 11-3 TE517 sensor location on turbocharger bend curve
To be noted in SCR installations

When urea injection is activated, urea water liquid and compressed air, which are colder than
exhaust gasses, are mixed into the hot exhaust gasses in the mixing and injection unit. This
endothermic reaction, which happens before SCR reactor, drops the exhaust gas temperature
from the engine t6 set point with approx. 5-10 °C. This means that exhaust gas temperature
just before the SCR reactor inlet is approx. 5-10 °C lower than temperature at TE517.
Temperature drop is load and exhaust gas flow dependent. Largest temperature drop affect
can therefore be seen on low engine loads, where urea injection ratio is higher compared to
the decreased exhaust gas flow.
The exothermic chemical reaction that is taking place inside the SCR reactor, increases the
exhaust gas temperature with approx. 10 °C. The exhaust gas temperature at SCR outlet is
therefore approx. the same as at TE517 sensor location.
When urea is not injected, its cooling affect before catalyst elements is not seen. This means
that SCR inlet and outlet temperatures should be even.
DAAB605808 11-3
Fig 11-4 Principle layout of SCR (Wärtsilä NOR)
11.3 Exhaust gas outlet
Engine TC in free end TC in driving end
W 4L20 0°, 30°, 60°, 90° -
W 6L20 0°, 30°, 60°, 90° 0°, 30°, 60°, 90°
W 8L20 0°, 30°, 60°, 90° 0°, 30°, 60°, 90°
W 9L20 0°, 30°, 60°, 90° 0°, 30°, 60°, 90°
Fig 11-5 Exhaust pipe connections

(DAAE066842)
11-4 DAAB605808
Engine ØA [mm] ØB [mm]
W 4L20 200 300
W 6L20 250 350 - 400
W 8L20 300 400 - 450
W 9L20 300 450
Fig 11-6 Exhaust pipe, diameters and sup-

port (DAAF014083)
DAAB605808 11-5
11.4 External exhaust gas system

Each engine should have its own exhaust pipe into open air. Backpressure, thermal expansion
and supporting are some of the decisive design factors.
Flexible bellows must be installed directly on the turbocharger outlet, to compensate for
thermal expansion and prevent damages to the turbocharger due to vibrations.
1 Diesel engine
2 Exhaust gas bellows
3 Connection for measurement of back pressure
4 Transition piece
5 Drain with water trap, continuously open
6 Bilge
7 SCR
8 Urea injection unit (SCR)
9 CSS silencer element
Fig 11-7 External exhaust gas sys-

tem
11.4.1 Piping
The piping should be as short and straight as possible. Pipe bends and expansions should
be smooth to minimise the backpressure. The diameter of the exhaust pipe should be increased
directly after the bellows on the turbocharger. Pipe bends should be made with the largest
possible bending radius; the bending radius should not be smaller than 1.5 x D.
The recommended flow velocity in the pipe is maximum 35…40 m/s at full output. If there are
many resistance factors in the piping, or the pipe is very long, then the flow velocity needs to
be lower. The exhaust gas mass flow given in chapter Technical data can be translated to
velocity using the formula:
where:
v = gas velocity [m/s]
m' = exhaust gas mass flow [kg/s]
T = exhaust gas temperature [°C]
D = exhaust gas pipe diameter [m]
11-6 DAAB605808
The exhaust pipe must be insulated with insulation material approved for concerned operation
conditions, minimum thickness 30 mm considering the shape of engine mounted insulation.
Insulation has to be continuous and protected by a covering plate or similar to keep the
insulation intact.
Closest to the turbocharger the insulation should consist of a hook on padding to facilitate
maintenance. It is especially important to prevent the airstream to the turbocharger from
detaching insulation, which will clog the filters.
After the insulation work has been finished, it has to be verified that it fulfils SOLAS-regulations.
Surface temperatures must be below 220°C on whole engine operating range.
11.4.2 Supporting
It is very important that the exhaust pipe is properly fixed to a support that is rigid in all
directions directly after the bellows on the turbocharger. There should be a fixing point on
both sides of the pipe at the support. The bellows on the turbocharger may not be used to
absorb thermal expansion from the exhaust pipe. The first fixing point must direct the thermal
expansion away from the engine. The following support must prevent the pipe from pivoting
around the first fixing point.
Absolutely rigid mounting between the pipe and the support is recommended at the first fixing
point after the turbocharger. Resilient mounts can be accepted for resiliently mounted engines
with “double” variant bellows (bellow capable of handling the additional movement), provided
that the mounts are self-captive; maximum deflection at total failure being less than 2 mm
radial and 4 mm axial with regards to the bellows. The natural frequencies of the mounting
should be on a safe distance from the running speed, the firing frequency of the engine and
the blade passing frequency of the propeller. The resilient mounts can be rubber mounts of
conical type, or high damping stainless steel wire pads. Adequate thermal insulation must be
provided to protect rubber mounts from high temperatures. When using resilient mounting,
the alignment of the exhaust bellows must be checked on a regular basis and corrected when
necessary.
After the first fixing point resilient mounts are recommended. The mounting supports should
be positioned at stiffened locations within the ship’s structure, e.g. deck levels, frame webs
or specially constructed supports.
The supporting must allow thermal expansion and ship’s structural deflections.
11.4.3 Back pressure

The maximum permissible exhaust gas back pressure is stated in chapter Technical Data. The
back pressure in the system must be calculated by the shipyard based on the actual piping
design and the resistance of the components in the exhaust system. The exhaust gas mass
flow and temperature given in chapter Technical Data may be used for the calculation.
Each exhaust pipe should be provided with a connection for measurement of the back pressure.
The back pressure must be measured by the shipyard during the sea trial.
11.4.4 Exhaust gas bellows (5H01, 5H03)

Bellows must be used in the exhaust gas piping where thermal expansion or ship’s structural
deflections have to be segregated. The flexible bellows mounted directly on the turbocharger
outlet serves to minimise the external forces on the turbocharger and thus prevent excessive
vibrations and possible damage. All exhaust gas bellows must be of an approved type.
11.4.5 SCR-unit (11N14)

The SCR-unit requires special arrangement on the engine in order to keep the exhaust gas
temperature and backpressure into SCR-unit working range. The exhaust gas piping must be
straight at least 3...5 meters in front of the SCR unit. If both an exhaust gas boiler and a SCR
unit will be installed, then the exhaust gas boiler shall be installed after the SCR. Arrangements
DAAB605808 11-7
must be made to ensure that water cannot spill down into the SCR, when the exhaust boiler
is cleaned with water.
More information about the SCR-unit can be found in the Wärtsilä Environmental Product
Guide.
11.4.6 Exhaust gas boiler

If exhaust gas boilers are installed, each engine should have a separate exhaust gas boiler.
Alternatively, a common boiler with separate gas sections for each engine is acceptable.
For dimensioning the boiler, the exhaust gas quantities and temperatures given in chapter
Technical data may be used.
11-8 DAAB605808
11.4.7 Exhaust gas silencers

The exhaust gas silencing can be accomplished either by the patented Compact Silencer
System (CSS) technology or by the conventional exhaust gas silencer.
11.4.7.1 Exhaust noise

The unattenuated exhaust noise is typically measured in the exhaust duct. The in-duct
measurement is transformed into free field sound power through a number of correction
factors.
The spectrum of the required attenuation in the exhaust system is achieved when the free
field sound power (A) is transferred into sound pressure (B) at a certain point and compared
with the allowable sound pressure level (C).
Fig 11-8 Exhaust noise, source power corrections
The conventional silencer is able to reduce the sound level in a certain area of the frequency
spectrum. CSS is designed to cover the whole frequency spectrum.
DAAB605808 11-9
11.4.7.2 Silencer system comparison

With a conventional silencer system, the design of the noise reduction system usually starts
from the engine. With the CSS, the design is reversed, meaning that the noise level acceptability
at a certain distance from the ship's exhaust gas pipe outlet, is used to dimension the noise
reduction system.
Fig 11-9 Silencer system comparison
11.4.7.3 Compact silencer system (5N02)

The CSS system is optimized for each installation as a complete exhaust gas system. The
optimization is made according to the engine characteristics, to the sound level requirements
and to other equipment installed in the exhaust gas system, like SCR, exhaust gas boiler or
scrubbers.
The CSS system is built up of three different CSS elements; resistive, reactive and composite
elements. The combination-, amount- and length of the elements are always installation
specific. The diameter of the CSS element is 1.4 times the exhaust gas pipe diameter.
The noise attenuation is valid up to a exhaust gas flow velocity of max 40 m/s. The pressure
drop of a CSS element is lower compared to a conventional exhaust gas silencer (5R02).
11-10 DAAB605808
11.4.7.4 Conventional exhaust gas silencer (5R02)

Yard/designer should take into account that unfavourable layout of the exhaust system (length
of straight parts in the exhaust system) might cause amplification of the exhaust noise between
engine outlet and the silencer. Hence the attenuation of the silencer does not give any absolute
guarantee for the noise level after the silencer.
When included in the scope of supply, the standard silencer is of the absorption type, equipped
with a spark arrester. It is also provided with a soot collector and a condense drain, but it
comes without mounting brackets and insulation. The silencer can be mounted either
horizontally or vertically.
The noise attenuation of the standard silencer is either 25 or 35 dB(A). This attenuation is valid
up to a flow velocity of max. 40 m/s.
Fig 11-10 Exhaust gas silencer (V49E0137B)
Table 11-1 Typical dimensions of exhaust gas silencers
Attenuation: 25 dB(A) Attenuation: 35 dB(A)
L [mm] Weight L [mm] Weight

NS D [mm] A [mm] B [mm] [kg] [kg]
300 860 1250 150 2530 360 3530 455
350 950 1405 115 2780 440 3780 580
400 1060 1500 150 3280 570 4280 710
450 1200 1700 180 3430 685 4280 855
500 1200 1700 200 3430 685 4280 860
Flanges: DIN 2501
DAAB605808 11-11
Wärtsilä 20 Product Guide 12. Turbocharger Cleaning
12. Turbocharger Cleaning

Regular water cleaning of the turbine and the compressor reduces the formation of deposits
and extends the time between overhauls. Fresh water is injected into the turbocharger during
operation. Additives, solvents or salt water must not be used and the cleaning instructions in
the operation manual must be carefully followed.
12.1 Turbine cleaning system

A dosing unit consisting of a flow meter and an adjustable throttle valve is delivered for each
installation. The dosing unit is installed in the engine room and connected to the engine with
a detachable rubber hose. The rubber hose is connected with quick couplings and the length
of the hose is normally 10 m. One dosing unit can be used for several engines.
Water supply:
Fresh water
Min. pressure 0.3 MPa (3 bar)
Max. pressure 2 MPa (20 bar)
Max. temperature 80 °C
Flow 6-10 l/min (depending on cylinder configuration)
Fig 12-1 Turbine cleaning system (DAAE003884)
01 Dosing unit with shut-off valve 502 Cleaning water to turbine Quick coupling
02 Rubber hose
12.2 Compressor cleaning system

The compressor side of the turbocharger is cleaned using a separate dosing vessel mounted
on the engine.
DAAB605808 12-1
Wärtsilä 20 Product Guide 13. Exhaust Emissions
13. Exhaust Emissions

Exhaust emissions from the diesel engine mainly consist of nitrogen, oxygen and combustion
products like carbon dioxide (CO2), water vapour and minor quantities of carbon monoxide
(CO), sulphur oxides (SOx), nitrogen oxides (NOx), partially reacted and non-combusted
hydrocarbons (HC) and particulate matter (PM).
There are different emission control methods depending on the aimed pollutant. These are
mainly divided in two categories; primary methods that are applied on the engine itself and
secondary methods that are applied on the exhaust gas stream.
13.1 Diesel engine exhaust components

The nitrogen and oxygen in the exhaust gas are the main components of the intake air which
don't take part in the combustion process.
CO2 and water are the main combustion products. Secondary combustion products are carbon
monoxide, hydrocarbons, nitrogen oxides, sulphur oxides, soot and particulate matters.
In a diesel engine the emission of carbon monoxide and hydrocarbons are low compared to
other internal combustion engines, thanks to the high air/fuel ratio in the combustion process.
The air excess allows an almost complete combustion of the HC and oxidation of the CO to
CO2, hence their quantity in the exhaust gas stream are very low.
13.1.1 Nitrogen oxides (NOx)

The combustion process gives secondary products as Nitrogen oxides. At high temperature
the nitrogen, usually inert, react with oxygen to form Nitric oxide (NO) and Nitrogen dioxide
(NO2), which are usually grouped together as NOx emissions. Their amount is strictly related
to the combustion temperature.
NO can also be formed through oxidation of the nitrogen in fuel and through chemical reactions
with fuel radicals. NO in the exhaust gas flow is in a high temperature and high oxygen
concentration environment, hence oxidizes rapidly to NO2. The amount of NO2 emissions is
approximately 5 % of total NOx emissions.
13.1.2 Sulphur Oxides (SOx)

Sulphur oxides (SOx) are direct result of the sulphur content of the fuel oil. During the
combustion process the fuel bound sulphur is rapidly oxidized to sulphur dioxide (SO2). A
small fraction of SO2 may be further oxidized to sulphur trioxide (SO3).
13.1.3 Particulate Matter (PM)

The particulate fraction of the exhaust emissions represents a complex mixture of inorganic
and organic substances mainly comprising soot (elemental carbon), fuel oil ash (together with
sulphates and associated water), nitrates, carbonates and a variety of non or partially
combusted hydrocarbon components of the fuel and lubricating oil.
13.1.4 Smoke
Although smoke is usually the visible indication of particulates in the exhaust, the correlations
between particulate emissions and smoke is not fixed. The lighter and more volatile
hydrocarbons will not be visible nor will the particulates emitted from a well maintained and
operated diesel engine.
Smoke can be black, blue, white, yellow or brown in appearance. Black smoke is mainly
comprised of carbon particulates (soot). Blue smoke indicates the presence of the products
DAAB605808 13-1
13. Exhaust Emissions Wärtsilä 20 Product Guide
of the incomplete combustion of the fuel or lubricating oil. White smoke is usually condensed
water vapour. Yellow smoke is caused by NOx emissions. When the exhaust gas is cooled
significantly prior to discharge to the atmosphere, the condensed NO2 component can have
a brown appearance.
13.2 Marine exhaust emissions legislation

13.2.1 International Maritime Organization (IMO)
The increasing concern over the air pollution has resulted in the introduction of exhaust
emission controls to the marine industry. To avoid the growth of uncoordinated regulations,
the IMO (International Maritime Organization) has developed the Annex VI of MARPOL 73/78,
which represents the first set of regulations on the marine exhaust emissions.
The IMO Tier 3 NOx emission standard will enter into force from year 2016. It will by then apply
for new marine diesel engines that:
● Are > 130 kW
● Installed in ships which keel laying date is 1.1.2016 or later
● Operating inside the North American ECA and the US Caribbean Sea ECA
From 1.1.2021 onwards Baltic sea and North sea will be included in to IMO Tier 3 NOx
requirements.
13.2.2 Other Legislations

There are also other local legislations in force in particular regions.
13.3 Methods to reduce exhaust emissions

All standard Wärtsilä engines meet the NOx emission level set by the IMO (International Maritime
Organisation) and most of the local emission levels without any modifications. Wärtsilä has
also developed solutions to significantly reduce NOx emissions when this is required.
Diesel engine exhaust emissions can be reduced either with primary or secondary methods.
The primary methods limit the formation of specific emissions during the combustion process.
The secondary methods reduce emission components after formation as they pass through
the exhaust gas system.
Refer to the "Wärtsilä Environmental Product Guide" for information about exhaust gas emission
control systems.
13-2 DAAB605808
Wärtsilä 20 Product Guide 14. Automation System
14. Automation System

The engine can be equipped with different automation system, depending on configuration.
14.1 UNIC C1
14.1.1 System overview
The auxiliary automation system consists of a built-on control system for control of the running
parameters, monitoring of the safety sensors and automatic safety operations.
14.1.2 Automation system scope

The engine mounted equipment mainly consists of :
● Main control unit ( MCM ) for control of starting and stopping sequences and speed control
of the generating set.
● Engine safety module ( ESM ) for measuring of engine speed and turbocharger speed and
for activation of automatic safety shutdowns ( over speed, low lubricating oil pressure and
high HT cooling water temperature. The ESM also performs wire break monitoring for the
safety system signals.
● Electric actuator for control of fuel rack position.
● Solenoids
● Sensors and switches for the ships alarm and monitoring system. The sensors are pre-wired
to a connection box on the generating set.
● Indicators for generating set speed, turbocharger speed and running hours.
● Local indications ( bar graphs ) for engine main parameters.
● Control mode switch Blow / Blocked / Local / Remote
● Emergency stop button
● Local start button
● Local stop button
● Shutdown reset button
14.1.3 Power supply

The power supply requirement for the auxiliary generating sets is 24 VDC, 5A at steady state,
and up to 20A for peaks (5 sec). UPS backed power supply is recommended. The control
system is designed so that a redundant power supply system can be adopted.
14.1.4 Safety System

The safety system is an independent system continuously monitoring the required parameters
for safe operation and performing shutdown of the generating set if the operating parameters
exceed preset limits. The parameters monitored are:
● Overspeed
● Low lubricating oil pressure
● High HT cooling water temperature
● Emergency stop button
DAAB605808 14-1
14. Automation System Wärtsilä 20 Product Guide
14.1.5 Start and stop system

The generating set is equipped with a built-on start and stop system for control of starting
and stopping sequences as well as start blocking functions.
14.1.5.1 Start blocking

Starting is inhibited by the following functions:
● Turning device engaged.
● Pre-lubricating pressure low. Starting is allowed within 30 minutes after the pressure has
dropped below the set point of 50 kPa.
● Engine start blocking selector switch turned into “Blocked” position
● Engine running
● Stop signal to engine activated (safety shut-down, emergency stop, normal stop)
● Stop lever in stop position
14.1.6 Speed control

The generating sets are provided with a built-on electronic speed control system and an
actuator. The system is designed for maximum reliability and optimum performance.
The speed measuring is performed with redundant speed pick-ups and failure of one speed
pick-up will not cause interference in the operation.
The speed control system has an integrated start fuel limiter for minimising smoke emission
during the acceleration period when starting an engine.
The dynamic response can be adjusted and optimised for the particular installation.
The speed control is set up for speed droop control mode operation and the speed droop is
factory adjusted for 4% at rated load. This is to ensure proper load sharing between paralleling
units. To compensate for the speed decrease of the plant when the load increases, and vice
versa when the load decreases, the ship should have a load sharing system with an outer
(cascade) loop to correct for the frequency drift.
14-2 DAAB605808
14.1.7 Sensors and signals

14.1.7.1 Local instrumentation
Fig 14-1 Connecting box and Local control panel
Thermometers
The generating set is as standard equipped with a bar graph type thermometer for HT cooling
water temperature mounted in the local control box.
Pressure gauges
The generating set is as standard equipped with the following bar graph type pressure gauges:
● Fuel pressure
● Lubricating oil pressure
● Starting air pressure
● Control air pressure
● HT cooling water pressure
● LT cooling water pressure
● Charge air pressure
Indication of rpm
The generating sets are equipped with local indication for engine speed and turbocharger
speed.
Generating set instrumentation

The generating sets are equipped with instrumentation for safety shutdowns and monitoring
of various parameters.
DAAB605808 14-3
Table 14-1 Engine to alarm system
Code Description I/O Signal Range Alarm Delay Note

type type set-
point
PT101 Fuel Oil Pressure, Engine inlet AI 4-20 mA 0-16 bar <4 5s
TE101 Fuel Oil Temperature, Engine inlet AI PT100 0-160°C
LS103A Fuel Oil Leakage, Injection Pipe DI Pot. free on/off OPEN 5s
PT201 Lubricating Oil Pressure, Engine AI 4-20 mA 0-10 bar <3 5s BL

inlet
TE201 Lubricating Oil Temperature, En- AI PT100 0-160°C > 75 5s
gine inlet
PDS243 Lubricating Oil Filter Pressure Differ- DI Pot. free on/off OPEN 5s Setpoint in
ence sensor >1.5
bar
LS204 Lubricating oil low level, oil sump DI Pot. free on/off OPEN 5s
LS205 Lubricating oil high level, oil sump DI Pot. free on/off OPEN 5s Optional
PT301 Starting Air Pressure, Engine inlet AI 4-20 mA 0-16 bar <7> 15/5 s
15
PT311 Control Air Pressure, Engine inlet AI 4-20 mA 0-40 bar < 16 5s
PT401 HT Water Pressure, Jacket inlet AI 4-20 mA 0-6 bar <2 5s BL
TE401 HT Water Temperature, Jacket inlet AI PT100 0-160°C < 60 5s
TE402 HT Water Temperature, Engine AI PT100 0-160°C > 105 5s

outlet
PT471 LT Water Pressure, CAC inlet AI 4-20 mA 0-6 bar <2 2s BL
TE471 LT Water Temperature, CAC inlet AI PT100 0-160°C > 55 5s
TE5011A- Exhaust Gas Temperature, Cylinder AI 4-20 mA 0-750°C > 480 10 s One sensor /
TE50X1A X outlet cylinder. See
Note 1)
TE517 Exhaust Gas Temperature, TC out- AI 4-20 mA 0-750°C > 450 2s
let
PT601 Charge Air Pressure, Engine inlet AI 4-20 mA 0-6 bar > 3.7 25 s
TE601 Charge Air Temperature, Engine AI PT100 0-160°C > 70 5s

inlet
ST173 Engine Speed AI 4-20 mA 0-1200
rpm
SE518 Turbo speed AI 4-20 mA 0-75000 See 5s
rpm table
14-2
IS875 Start Failure DI Pot. free on/off OPEN 2s
IS1741/ Overspeed, shutdown DI Pot. free on/off OPEN 2s Setpoint in

IS1742 ESM: >115%
IS4011 HT-Water Temperature High, Shut- DI Pot. free on/off OPEN 2s Setpoint in
down ESM:
>110°C
IS2011 Lubricating Oil Pressure Low, DI Pot. free on/off OPEN 2s Setpoint in
Shutdown ESM:
<2.0bar
14-4 DAAB605808

type type set-
point
NS161 Actuator major failure, Shutdown DI Pot. free on/off OPEN 2s
IS7305 Emergency Stop DI Pot. free on/off OPEN 2s
NS881 Engine Control System Minor Alarm DI Pot. free on/off OPEN 2s
NS718 ESM failure DI Pot. free on/off OPEN 2s
NS7799- PDM System Supply Earth Fault DI Pot. free on/off OPEN 2s
1
NS7800- PDM System Supply Failure DI Pot. free on/off OPEN 2s
1
NS869 WIP Failure DI Pot. free on/off OPEN 2s
OS820/ Engine Control System Major Fail- DI Pot. free on/off OPEN 2s
NS886 ure
IS780 Alarm Blocking DI Pot. free on/off CLOSED 2s Blocking all
alarms
marked with
BL
Table 14-2 Alarm setpoint for SE518 Turbo speed
Engine TC speed high alarm
4L20 60850 rpm
6L20 48000 rpm
8L20 41500 rpm
9L20 41500 rpm
Table 14-3 Generator to alarm system

type type set-
point
TE7501 Bearing Temperature, DE AI PT100 0-160°C > 85 2s If two bear-
ing
TE7502 Bearing Temperature, NDE AI PT100 0-160°C > 85 2s
TE7503 Winding Temperature, L1 AI PT100 0-160°C > 155 2s
TE75?? Air Temperature, Cooler Inlet AI PT100 0-160°C > 75 2s If water

cooled
LS7506 Cooling Water Leakage 1 DI Pot. free on/off OPEN 2s If water
cooled
Note 1) Alarm when exhaust gas temperature deviation >±100°C/>±50°C from average when
average temperature is 250/450°C. Deviation alarm to be blocked when average temperature
<250°C.
DAAB605808 14-5
14.1.8 Control of auxiliary equipment

14.1.8.1 Pre-lubricating oil pump
The engine is equipped with an electric pre-lubricating pump.
The pre-lubricating pump is used for filling of the lubricating oil system, pre-lubricate a stopped
engine before start and for pre-heating by circulating warm lubricating oil. The colder the
engine is, the earlier the pump should be started before the engine is started.
The pump may also be run continuously when the engine is stopped and must run in multiple
engine installations when other engines are running.
To ensure continuous pre-lubrication of a stopped engine, automatic starting and stopping
of the pre-lubricating pump is recommended. This can be achieved using the pre-lubricating
oil pump control output in the engine control system.
The generating sets can be supplied ( option ) with a pre-lubrication pump starter box. The
starter is of bulkhead mount type with a starter contactor, overload protection and control
system for the pump. The starters have indicating lights for power on, pump running and pump
failure as well as a control switch for automatic or manual operation. The starter box can
control pre-lubrication pumps of up to 4 generating sets.
Fig 14-2 Pre-lubricating pump starter (DAAE005967A)
Technical data of pre-lubrication pumps:
WA20
400V / 50Hz 3.0kW, ln = 6.0A
14-6 DAAB605808
WA20
440V / 60 Hz 3.7kW In = 6.2A
14.1.8.2 Cooling water pre-heater and circulation pump

Pre-heating is done by an electric or steam pre-heater with a required heating power depending
of the engine type. The temperature control of the pre-heater should be made automatic with
a control thermostat. The heater and the circulation pump should be controlled from the
pre-heater control output in the engine control system. For pre-heating unit see section
"Pre-heating" in chapter "Cooling Water System".
14.2 UNIC C2
UNIC C2 is a fully embedded and distributed engine management system, which handles all
control functions on the engine; for example start sequencing, start blocking, speed control,
load sharing, normal stops and safety shutdowns.
The distributed modules communicate over a CAN-bus. CAN is a communication bus
specifically developed for compact local networks, where high speed data transfer and safety
are of utmost importance.
The CAN-bus and the power supply to each module are both physically doubled on the engine
for full redundancy.
Control signals to/from external systems are hardwired to the terminals in the main cabinet
on the engine. Process data for alarm and monitoring are communicated over a Modbus TCP
connection to external systems.
Alternatively modbus RTU serial line RS-485 is also available.
Fig 14-3 Architecture of UNIC C2
Short explanation of the modules used in the system:
MCM Main Control Module. Handles all strategic control functions (such as start/stop sequen-
cing and speed/load control) of the engine.
DAAB605808 14-7
ESM Engine Safety Module handles fundamental engine safety, for example shutdown due
to overspeed or low lubricating oil pressure.
LCP Local Control Panel is equipped with push buttons and switches for local engine control,
as well as indication of running hours and safety-critical operating parameters.
LDU Local Display Unit offers a set of menus for retrieval and graphical display of operating
data, calculated data and event history. The module also handles communication with
external systems over Modbus TCP.
PDM Power Distribution Module handles fusing, power distribution, earth fault monitoring
and EMC filtration in the system. It provides two fully redundant supplies to all modules.
IOM Input/Output Module handles measurements and limited control functions in a specific
area on the engine.
CCM Cylinder Control Module handles fuel injection control and local measurements for the
cylinders.
The above equipment and instrumentation are prewired on the engine. The ingress protection
class is IP54.
14.2.1 Local control panel and local display unit

Operational functions available at the LCP:
● Local start
● Local stop
● Local emergency speed setting selectors (mechanical propulsion):
○ Normal / emergency mode
○ Decrease / Increase speed
● Local emergency stop
● Local shutdown reset
Local mode selector switch with the following positions:
○ Local: Engine start and stop can be done only at the local control panel
○ Remote: Engine can be started and stopped only remotely
○ Blow: In this position it is possible to perform a “blow” (an engine rotation check with
indicator valves open and disabled fuel injection) by the start button
○ Blocked: Normal start of the engine is not possible
The LCP has back-up indication of the following parameters:

● Engine speed
● Turbocharger speed
● Running hours
● Lubricating oil pressure
● HT cooling water temperature
The local display unit has a set of menus for retrieval and graphical display of operating data,
calculated data and event history.
14-8 DAAB605808
Fig 14-4 Local control panel and local display unit
14.2.2 Engine safety system

The engine safety module handles fundamental safety functions, for example overspeed
protection. It is also the interface to the shutdown devices on the engine for all other parts of
the control system.
Main features:
● Redundant design for power supply, speed inputs and stop solenoid control
● Fault detection on sensors, solenoids and wires
● Led indication of status and detected faults
● Digital status outputs
● Shutdown latching and reset
● Shutdown pre-warning
● Shutdown override (configuration depending on application)
● Analogue output for engine speed
● Adjustable speed switches
14.2.3 Power unit

A power unit is delivered with each engine. The power unit supplies DC power to the automation
system on the engine and provides isolation from other DC systems onboard. The cabinet is
designed for bulkhead mounting, protection degree IP44, max. ambient temperature 50°C.
DAAB605808 14-9
The power unit contains redundant power converters, each converter dimensioned for 100%
load. At least one of the two incoming supplies must be connected to a UPS. The power unit
supplies the equipment on the engine with 2 x 24 VDC.
Power supply from ship's system:
● Supply 1: 230 VAC / abt. 250 W
● Supply 2: 24 VDC / abt. 250 W
14.2.4 Ethernet communication unit

Ethernet switch and firewall/router are installed in a steel sheet cabinet for bulkhead mounting,
protection class IP44.
14.2.5 Cabling and system overview
Fig 14-5 UNIC C2 overview
Table 14-4 Typical amount of cables
Cable From <=> To Cable types (typical)
A Engine <=> Power Unit 2 x 2.5 mm2 (power supply) *

2 x 2.5 mm2 (power supply) *
B Power unit => Communication interface unit 2 x 2.5 mm2 (power supply) *
C Engine <=> Propulsion Control System 1 x 2 x 0.75 mm2

Engine <=> Power Management System / Main Switch- 1 x 2 x 0.75 mm2
board 1 x 2 x 0.75 mm2
24 x 0.75 mm2
24 x 0.75 mm2
D Power unit <=> Integrated Automation System 2 x 0.75 mm2
E Engine <=> Integrated Automation System 3 x 2 x 0.75 mm2
F Engine => Communication interface unit 1 x Ethernet CAT 5
G Communication interface unit => Integrated automation 1 x Ethernet CAT 5

system
H Gas valve unit => Communication interface unit 1 x Ethernet CAT 5
14-10 DAAB605808
NOTE
Cable types and grouping of signals in different cables will differ depending on
installation.
* Dimension of the power supply cables depends on the cable length.
Power supply requirements are specified in section Power unit.
Fig 14-6 Signal overview (Main engine)
DAAB605808 14-11
Fig 14-7 Signal overview (Generating set)
14.2.6 Function
14.2.6.1 Start
The engine has a pneumatic starting motor controlled by a solenoid valve. The solenoid valve
can be energized either locally with the start button, or from a remote control station. In an
emergency situation it is also possible to operate the valve manually.
Starting is blocked both pneumatically and electrically when the turning gear is engaged. Fuel
injection is blocked when the stop lever is in stop position (conventional fuel injection).
Startblockings are handled by the system on the engine (main control module).
Startblockings
Starting is inhibited by the following functions:
● Turning gear engaged
● Stop lever in stop position
● Pre-lubricating pressure low
● Local engine selector switch in blocked position
● Stop or shutdown active
● External start blocking 1 (e.g. reduction gear oil pressure)
● External start blocking 2 (e.g. clutch position)
● Engine running
For restarting of a diesel generator in a blackout situation, start blocking due to low
pre-lubricating oil pressure can be suppressed for 30 min.
14-12 DAAB605808
14.2.6.2 Stop and shutdown

Normal stop is initiated either locally with the stop button, or from a remote control station.
The control devices on the engine are held in stop position for a preset time until the engine
has come to a complete stop. Thereafter the system automatically returns to “ready for start”
state, provided that no start block functions are active, i.e. there is no need for manually
resetting a normal stop.
Manual emergency shutdown is activated with the local emergency stop button, or with a
remote emergency stop located in the engine control room for example.
The engine safety module handles safety shutdowns. Safety shutdowns can be initiated either
independently by the safety module, or executed by the safety module upon a shutdown
request from some other part of the automation system.
Typical shutdown functions are:

● Lubricating oil pressure low
● Overspeed
● Lubricating oil pressure low in reduction gear
Depending on the application it can be possible for the operator to override a shutdown. It is
never possible to override a shutdown due to overspeed or an emergency stop.
Before restart the reason for the shutdown must be thoroughly investigated and rectified.
14.2.6.3 Speed control

Main engines (mechanical propulsion)
The electronic speed control is integrated in the engine automation system.
The remote speed setting from the propulsion control is an analogue 4-20 mA signal. It is also
possible to select an operating mode in which the speed reference can be adjusted with
increase/decrease signals.
The electronic speed control handles load sharing between parallel engines, fuel limiters, and
various other control functions (e.g. ready to open/close clutch, speed filtering). Overload
protection and control of the load increase rate must however be included in the propulsion
control as described in the chapter "Operating ranges".
For single main engines a fuel rack actuator with a mechanical-hydraulic backup governor is
specified. Mechanical back-up can also be specified for twin screw vessels with one engine
per propeller shaft. Mechanical back-up is not an option in installations with two engines
connected to the same reduction gear.
Generating sets
The electronic speed control is integrated in the engine automation system.
The load sharing can be based on traditional speed droop, or handled independently by the
speed control units without speed droop. The later load sharing principle is commonly referred
to as isochronous load sharing. With isochronous load sharing there is no need for load
balancing, frequency adjustment, or generator loading/unloading control in the external control
system.
In a speed droop system each individual speed control unit decreases its internal speed
reference when it senses increased load on the generator. Decreased network frequency with
higher system load causes all generators to take on a proportional share of the increased total
load. Engines with the same speed droop and speed reference will share load equally. Loading
and unloading of a generator is accomplished by adjusting the speed reference of the individual
speed control unit. The speed droop is normally 4%, which means that the difference in
frequency between zero load and maximum load is 4%.
DAAB605808 14-13
In isochronous mode the speed reference remains constant regardless of load level. Both
isochronous load sharing and traditional speed droop are standard features in the speed
control and either mode can be easily selected. If the ship has several switchboard sections
with tie breakers between the different sections, then the status of each tie breaker is required
for control of the load sharing in isochronous mode.
14.2.7 Alarm and monitoring signals

Regarding sensors on the engine, please see the internal P&I diagrams in this product guide.
The actual configuration of signals and the alarm levels are found in the project specific
documentation supplied for all contracted projects.
14.2.8 Electrical consumers

14.2.8.1 Motor starters and operation of electrically driven pumps
Separators, preheaters, compressors and fuel feed units are normally supplied as
pre-assembled units with the necessary motor starters included. Various electrically driven
pumps require separate motor starters. Motor starters for electrically driven pumps are to be
dimensioned according to the selected pump and electric motor.
Motor starters are not part of the control system supplied with the engine, but available as
optional delivery items.
Pre-lubricating oil pump

The pre-lubricating oil pump must always be running when the engine is stopped. When engine
stops, there is need for TC cooling by post-lubrication. Therefore the pre-lubrication pump
shall run at least 90 minutes after an engine stop.
● The lubricating oil pressure should be between 0.6 – 0.7 bar and must be higher than the
start blocking pressure
● Engines equipped with an air by-pass valve can, if possible, keep the air by-pass valve
open when the engine is stopped to increase the cooling ability
The pump shall start when the engine stops, and stop when the engine starts. The engine
control system handles start/stop of the pump automatically via a motor starter.
It is recommended to arrange a back-up power supply from an emergency power source.
Diesel generators serving as the main source of electrical power must be able to resume their
operation in a black out situation by means of stored energy. Depending on system design
and classification regulations, it may be permissible to use the emergency generator.
For dimensioning of the pre-lubricating oil pump starter, the values indicated below can be
used. For different voltages, the values may differ slightly.
Table 14-5 Electric motor ratings for pre-lubricating pump
Engine type Voltage [V] Frequency [Hz] Power [kW] Current [A]
Wärtsilä 20 3 x 400 50 3.0 6.0
3 x 440 60 3.5 6.2
Stand-by pump, lubricating oil (if installed) (2P04)

The engine control system starts the pump automatically via a motor starter, if the lubricating
oil pressure drops below a preset level when the engine is running. There is a dedicated sensor
on the engine for this purpose.
14-14 DAAB605808
The pump must not be running when the engine is stopped, nor may it be used for
pre-lubricating purposes. Neither should it be operated in parallel with the main pump, when
the main pump is in order.
Stand-by pump, HT cooling water (if installed) (4P03)

The engine control system starts the pump automatically via a motor starter, if the cooling
water pressure drops below a preset level when the engine is running. There is a dedicated
sensor on the engine for this purpose.
Stand-by pump, LT cooling water (if installed) (4P05)

The engine control system starts the pump automatically via a motor starter, if the cooling
water pressure drops below a preset level when the engine is running. There is a dedicated
sensor on the engine for this purpose.
Circulating pump for HT preheater (4P04)

The preheater pump shall start when the engine stops (to ensure water circulation through
the hot engine) and stop when the engine starts. The engine control system handles start/stop
of the pump automatically via a motor starter.
DAAB605808 14-15
14.3 UNIC 2nd Generation

14.3.1 General Description
14.3.1.1 System Overview
The UNIC automation system is an embedded engine management system. The system has
a modular design, and some parts and functions in the UNIC configuration are optional
depending on application. The system is specifically designed for the demanding environment
on engines, thus special attention has been paid to temperatureand vibration endurance. This
allows the system to be mounted directly on engine that provides a compact design. The
number of inputs and outputs are determined to optimally suit this system arrangement, and
the galvanic signal isolation is also made to match these needs.
The UNIC system handles all tasks related to start/stop management, engine safety, fuel
management and speed/load control, as well as charge air, cooling, and combustion. The
system utilizes modern bus technologies for safe transmission of sensor- and other signals.
The UNIC automation system can be accessed with a software-based maintenance tool, which
is used for tuning parameters, troubleshooting and for software installation.
Fig 14-8 UNIC System Overview
14.3.1.2 Main Cabinet

The main cabinet is a main hub of the UNIC control system. All engine external systems are
connected via the main cabinet. In addition, all the power supply connections for engine
components and actuators are distributed through the main cabinet. The main cabinet holds
an Engine Safety Module (ESM) and a number of Communication Modules (COM). Based on
engine installation the additional Input / Output Modules (IOM) can be added to main cabinet.
The major parts inside the main cabinet are:
● Communication module, COM The communication module is the main gateway to the
UNIC system, supporting multiple interfaces such as Modbus, OPC, hardwired I/O, etc.
COM is a key module for UNIC system communication and responsible for several control
functions, software and configuration update management. Depending on engine application
the number of COM modules in the main cabinet can vary from 2 to 5 units.
14-16 DAAB605808
● Engine Safety module, ESM The engine safety module handles the most fundamental
engine safety functions related to engine over-speed protection, low lube oil pressure and
other safety functions required by classification societies. The ESM is able to shutdown
the engine without relaying on any other system functions.
● Input / Output module, IOM When placed inside the main cabinet the IOM module extends
the number of input/output channels in UNIC for the on-engine measurements.
14.3.1.3 Distributed Modules

Around the engine close to inputs and outputs being monitored and / or controlled there are
specially designed terminal boxes (WTB) containing UNIC distributed modules. Communication
bus HSR allow the distributed modules to communicate with the COM’s inside the main
cabinet.
● Input / Output module, IOM These modules are placed close to inputs and outputs around
the engine. When distributed on the engine the main functions of IOM is to measure
temperature, pressure and turbo speed. The collected information is then sent to COM for
machinery protection evaluation or further distribution to local display and external systems.
The IOM module also performs engine some control functions such as exhaust and air
waste gate control, VIC solenoid activation.
14.3.1.4 Local Operator Panel

On engines equipped with a jerk-pump system the local control panel is placed close to the
stop lever in order to provide support for the operator in case the lever needs to be operated
based on information read from the display.
● Local Display Unit, LDU A configurable display showing all relevant data collected by
UNIC. In addition to the display it contains 4 physical buttons used for various functions.
Main use of the buttons are engine start, stop, hutdown reset and local/ remote control
selection.
● Emergency stop push button An emergency stop push button is always located next to
the LDU for stopping the engine quickly in any situation this is seen needed.
14.3.1.5 Software
Platform Software
Wärtsilä Modular Application Platform (WMAP) is the system software in the UNIC control
system. The Wärtsilä control applications are implemented on top the WMAP.
The WMAP platform software ensures that safety, control and measurement functions of the
system are performed in the strictly defined order.
Control Application
Certain UNIC functionality such as speed and load controller or engine mode control are
implemented as control application modules. The control application modules are executed
periodically with a defined time interval and in a defined order.
Maintenance and Monitoring Tool

Wärtsilä UNITool is the maintenance and monitoring tool used for engine troubleshooting,
monitoring and tuning of the engine parameters. The UNIC software download as well as
software configuration is also accomplished with UNITool.
DAAB605808 14-17
14.3.2 UNIC Hardware

14.3.2.1 Mechanical Design
The UNIC system is designed to meet very high targets on reliability. This includes special
measures for redundancy, fault tolerance as well as mechanical and electrical design. The
sensors and actuators are designed to be reliable, easy to service and to calibrate. Flying lead
design is introduced (wherever possible) to avoid failure prone connectors. Only cables suitable
for the demanding engine environment are used on the engines. The well protected
point-to-point cables provide the most reliable solution, as they ensure good protection against
electrical disturbances, high mechanical strength as well as good protection against chemicals
and temperature. Electronic modules which are distributed on the engine, are mounted in
specially designed terminal boxes (WTB).
These enclosures are used to facilitate all interconnections on the engine, i.e. they are acting
as an interface between the control modules and their peripheral devices.
Fig 14-9 Enclosure for Module Interconnections and Cabling
14.3.2.2 Power Supply

Overview
The required power supply domains are sourced from an off-engine power unit and routed to
engine’s main cabinet. From there the power supplies are distributed to correct consumers
at the engine automation system. Depending on the engine type and functionalities, some of
the power supplies may be combined to the same supply.
14-18 DAAB605808
Fig 14-10 Overview of Power Supply Arrangement (One Engine)
Redundancy
UNIC engine automation has input for two supplies per power domain (PSS, PSDx, PSA). The
system can operate with one supply per domain in case of failure in the redundant supply.
When operating on redundant supplies these are arranged so that single failure can not cause
system misbehaviour. In the system consumers, the redundant supplies are combined to one
supply in the component design in a way that internal short circuit of the component does not
interfere permanently the rest of the power supply system.
DCM is a power supply converter and it is located at the power unit with the circuit breakers
Fig 14-11 Example of the Redundancy and the Division of UNIC Power Supply System
Earth Fault Detection

Each pair of redundant power supply domains has a common earth fault detector in the power
unit.
Fuse Selectivity
The UNIC system components are designed to withstand 20ms power cut without rebooting.
This is the time window in which the fusing system must react to have at least one of the two
redundant supplies recovered after the short circuit situation. The system’s selectivity consists
of circuit breakers, fuses and dedicated current limitation. The whole chain is designed so
that only the failed branch of the system shuts down in case of short circuit. Rest of the system
can continue the operation normally.
DAAB605808 14-19
Fig 14-12 Fuse Selectivity Principle of Power Supply System
14.3.2.3 UNIC Modules

Local Display Unit Module
The LDU is an interface to the control and monitoring system of the engine.
Communication Module
The Communication Module (COM) is designed to primarily act as the interface of UNIC.
The module also measures the engine speed and position. External control systems can be
connected to UNIC system via the COM module. For control and monitoring purposes it is
also possible to connect a number of discrete and/ or analogue signals to the configurable in
and output channels.
Input and Output Module

The Input and Output Module (IOM) is used for data acquisition of analogue/ binary/ frequency
signals, and also for control, such as waste-gate valve control, by-pass valve control and
LT/HT water thermostat valve control.
Power Supply
There are two redundant 24 VDC power supply inputs. Therefore a failure in one power supply
will not affect the function of the module.
● Typical operating voltage: 24 VDC
● Operating voltage range: 18-32 VDC
● Protection: overvoltage, under voltage, transients, surge, electronic fuse
Diagnostics: Input current measurement, input voltage measurement
14-20 DAAB605808
Inputs and Outputs
Fig 14-13 IOM module I/O types
High Availability Seamless Redundancy network

High Availability Seamless Redundancy (HSR) network interface is used for communication
between UNIC modules which support HSR protocol.
Controller Area Network
Controller area network (CAN) interface can be used for communication with other CAN enabled
devices.
LED Indication
Fig 14-14 Status LED
DAAB605808 14-21
14.3.2.4 Engine Safety Module

The Engine Safety Module (ESM) is an electronic control unit specifically designed for the
purpose of fundamental safety on Wärtsilä engines
14.3.3 UNIC Functionality

14.3.3.1 Engine Mode Control
The UNIC engine management system controls and monitors a number of engine parameters
and initiates all required actions under various engine conditions. These actions can vary from
blocking a start, to initiating an alarm, or to shutting down the engine. That is the reason why
UNIC has a number of engine modes. Different modes have different priority, and the mode
transitions can occur only according to the predefined rules.
Fig 14-15 Engine Mode Control Overview
Stop Mode
Stop mode can be entered from stand-by mode, shutdown mode or emergency stop mode.
Stand-by Mode
Stand-by mode can be entered only from stop mode.
Start Mode
A start mode can be entered only from stand-by mode.
14-22 DAAB605808
Run Mode
A run mode can only be entered from a start mode if no stop, shutdown or emergency stop
requests are active. The transition from start to run mode happens when an engine rotational
speed is above a pre-set run mode speed limit.
Shutdown Mode
A shutdown mode can be entered from a stop mode, stand-by mode, start mode or a run
mode.
Emergency Stop Mode

Emergency stop mode has the highest priority and can be entered from any other mode.
14.3.3.2 Engine Speed Measurement

Speed sensors mounted close to the flywheel measure the engine speed. The engine speed
is used for the internal speed and load controller, engine speed-dependent control maps and
over-speed protection. Two speed sensors installed on separate modules for full mechanical
separation and redundancy. Any speed sensor failure or a COM module failure moves the
engine speed calculation to the other COM module without affecting engine performance.
14.3.3.3 Speed/ Load Controller

The UNIC speed/load control sets the engine fuel demand.
The speed or load reference is calculated and used in the closed-loop speed/load controller
to set the engine fuel demand.
Synchronizing/ Clutch-in
Synchronization/clutching in is needed before transferring from CB open mode to the other
control modes.
Load Sharing
Load sharing is done to divide the load between the engines.
Speed/ Load Modes

The UNIC speed/load controller has four different speed load control modes.
CB open control
CB open control is active during engine start, and in run mode until the generator breaker or
the clutch has been closed. Start fuel limiter is used in this mode. Binary/ analogue inputs are
enabled for synchronisation purpose. The PID parameters are engine speed dependent.
Speed droop control and load sharing
Speed droop control and load sharing become active after the closure of the generator breaker
or the clutch. Load sharing is based on a built-in droop curve, which means that the internal
engine speed reference will decrease proportionally to the load increase. After a major load
increase, the internal speed reference may need to be increased by the power management
system (PMS) to ensure that the bus frequency is kept within a certain window regardless of
the net load level. Control of the speed reference from a plant management system is necessary.
The PID parameters are dependent on the engine speed and load.
Isochronous control and load sharing
Isochronous control and load sharing become active after closure of the generator breaker or
the clutch when isochronous load sharing has been selected. In this control mode the load
sharing is provided over load sharing CAN. The engine speed remains unaffected by a droop
slope at all load levels without speed reference adjustments from a plant management system.
The PID parameters are dependent on the engine speed and load.
DAAB605808 14-23
True kW control
True kW control becomes active after the closure of the generator breaker when kW control
has been selected. The mode is used normally for operation in parallel with the grid, but it can
also be used in island mode, for a limited number of engines. Engine speed is used only to
ensure that the speed range is within defined engine safety- and BMEP limits. The PID
parameters are engine load dependent.
Fuel Demand Limiters

The fuel demand set by the speed/load controller can be limited using fuel demand limiters.
The following demand limiters are available:
● A start fuel limiter is used during engine start, and a clutch-in limiter when clutching in a
single main engine application or the first engine of a tandem main engine application.
● The fuel demand can also be limited using engine load, engine speed or charge air pressure
dependent limiters.
If several limiters are active simultaneously, the maximum fuel demand level is determined
according to the lowest limiter value.
14.3.3.4 Air and Exhaust

Variable Inlet Valve Control
Variable Inlet valve Closing (VIC) controls the closing of the inlet valves.
The inlet valve closing can be delayed to reduce which improves low load running, emergency
loading and transient operation. At medium and higher load the camshaft profile (increased
timing) can be utilized to reduce the compression temperature which results in reduced NOx
emissions and reduce the specific fuel-oil consumption (SFOC).
The VIC valve is activated based on engine load and speed. In addition, during positive load
transients and active emergency loading rate situations, the VIC is also activated. For engine
safety reasons the VIC is disabled if the charge air pressure is above a preset limit regardless
of the state of the other activation components.
Waste-gate Valve Control

UNIC controls one or more waste-gate valves to regulate the amount of air fed into the engine
by controlling the charge air pressure.
Charge air pressure control
The charge air pressure control is a closed loop control with an engine speed and load based
charge air pressure set-point. The engine is fitted with charge air pressure sensor(s) which is
used as feedback to the control. The waste-gate control limits the charge air pressure on
higher engine loads.
Exhaust gas temperature control
The exhaust gas temperature control is used regulate the exhaust gas temperature to a load
based set-point temperature to ensure optimal exhaust treatment done by the selective catalytic
reduction (SCR) system. The exhaust gas temperature control is available as an additional
control method for the waste-gate control. It is activated/ deactivated with an external input
to the UNIC system.
14.3.3.5 Fuel Rack Actuator Control

The amount of fuel to be injected by each injector is set by a mechanical linkage called the
fuel rack. UNIC controls the fuel rack position via analogue output. The position of the fuel
rack is controlled based on the calculated fuel demand required to maintain the desired engine
speed or load.
14-24 DAAB605808
14.3.4 UNIC Machinery Protection

Most sensors connected to UNIC have some machinery protection specified. Depending on
how critical an abnormal measurement is for the engine, different levels of protective actions
are configured. UNIC machinery protection is divided in the following classes:
● Alarm
● Start Blocking
● Load Reduction Request
● Shutdown
● Emergency Stop
14.3.4.1 Alarm
When a monitored engine signal exceeds its pre-defined set-point, an alarm is activated. The
alarm is presented in the external alarm system and in the local display. All alarms trigger the
"common alarm" signal, which toggles off and on again each time a new alarm triggers it.
Sensor / signal failure alarm (SF)
All analogue input and output signals have pre-set min and max limits defined for the electrical
signal. In case either of these are exceeded the signal is set to sensor / signal failure status.
When a signal is set to SF status, it is no longer used by machinery protection.
Set point alarm (SP)
A set point alarm is activated when input signal value or internally calculated values (such as
temperature or pressure deviation) exceeds a configured value i.e. set point.
14.3.4.2 Start Blocking

Engine starting is blocked when a start block is active. Start blocking signals are connected
to the COM module or to an IOM module. It is not allowed to by-pass a start blocking since
it may cause a serious hazard either for the engine and its surrounding or for associated
systems.
14.3.4.3 Load Reduction Request

Load reduction request is an automatic safety measure initiated by UNIC, used to reduce the
maximum load output of the engine under certain abnormal engine conditions. Whenever
there is an abnormal situation on the engine or the generator, which endangers a secure or
proper operation of the engine, a SP (Set Point) load reduction or SF (Sensor Failure) load
reduction can be activated. The maximum available load output can be different depending
of the type of abnormality. UNIC interacts with the external plant management system,
particularly in case of speed droop control mode.
14.3.4.4 Shutdown and Emergency Stop

An engine shutdown or an emergency stop can be initiated by UNIC or by a protective safety
system. Wärtsilä has an internal standard that defines engine shutdowns, unavoidable
shutdowns and emergency stops which are anaged by the UNIC control system.
14.3.5 Protective Safety System

The main tasks of protective system on engine:
● Engine Shutdown in Case of an Overspeed Situation
● Engine Shutdown in Case of Too Low Lubricating Oil Pressure
● Engine Shutdown in Case of Too High HT Cooling Water Temperature
DAAB605808 14-25
● Fault Detection on Sensors, Solenoid and Wires
14.3.5.1 Shutdown and Emergency Stop

The protective safety system showdowns are always communicated to UNIC, however
protective system is cable of engine shutdown even if the UNIC system is not operational or
communication between the two systems is broken. Critical sensors are connected to the
Engine Safety Module (ESM), and their measurements can activate automatic shutdowns. All
shutdowns initiated by ESM are communicated to UNIC via CANOpen communication bus.
The shutdowns are latching and require a reset before the engine can be restarted.
As a minimum, the engine is equipped with the following sensors/signals that can cause an
automatic shutdown or emergency stop:
● Emergency Stop Button
● Low Lubrication Oil Pressure, Engine Inlet
● Engine Speed (Overspeed Trip)
Emergency Stop Button

Pressing the local or (engine) external emergency stop button shuts down the engine instantly.
Both the external emergency stop signal and the local HS723 emergency stop button activate
"OS7305 External shutdown 4".
Low Lubricating Oil Pressure Shutdown

A dedicated safety pressure transmitter "PTZ201 LO press, engine inlet" is connected to the
engine safety module (ESM). It activates the engine shutdown if the lubricating oil pressure is
too low. If a transmitter failure is detected, the shutdown is blocked and a sensor failure is
indicated.
High HT Water Temperature Shutdown

Dedicated safety sensors TEZ402 and TEZ403 (for V-engines) are connected to the ESM for
the activation of shutdown in case of high HT water temperature. For V-engines, the ESM
always uses the higher of the values received from the two sensors. If a sensor failure is
detected, the shutdown is blocked and a sensor failure indicated.
Engine Overspeed Shutdown

The engine speed is measured with two independent speed sensors ST173 and ST174 that
are connected to ESM module. The measured values are used to trig the internal overspeed
trip circuits. The triggering point for the overspeed shutdown is set to 115% of the nominal
engine speed.
14-26 DAAB605808
Wärtsilä 20 Product Guide 15. Foundation
15. Foundation
Engines can be either rigidly mounted on chocks, or resiliently mounted on rubber elements.
If resilient mounting is considered, Wärtsilä must be informed about existing excitations such
as propeller blade passing frequency. Dynamic forces caused by the engine are listed in the
chapter Vibration and noise.
15.1 Steel structure design

The system oil tank may not extend under the reduction gear, if the engine is of dry sump type
and the oil tank is located beneath the engine foundation. Neither should the tank extend
under the support bearing, in case there is a PTO arrangement in the free end. The oil tank
must also be symmetrically located in transverse direction under the engine.
The foundation and the double bottom should be as stiff as possible in all directions to absorb
the dynamic forces caused by the engine, reduction gear and thrust bearing. The foundation
should be dimensioned and designed so that harmful deformations are avoided.
The foundation of the driven equipment must be integrated with the engine foundation.
15.2 Mounting of main engines

15.2.1 Rigid mounting
Main engines can be rigidly mounted to the foundation either on steel chocks or resin chocks.
Prior to installation the shipyard must send detailed plans and calculations of the chocking
arrangement to the classification society and to Wärtsilä for approval.
The engine has four feet integrated to the engine block. There are two Ø22 mm holes for M20
holding down bolts and a threaded M16 hole for a jacking screw in each foot. The Ø22 holes
in the seating top plate for the holding down bolts can be drilled though the holes in the engine
feet. In order to avoid bending stress in the bolts and to ensure proper fastening, the contact
face underneath the seating top plate should be counterbored.
Holding down bolts are through-bolts with lock nuts. Selflocking nuts are acceptable, but hot
dip galvanized bolts should not be used together with selflocking (nyloc) nuts. Two of the
holding down bolts are fitted bolts and the rest are clearance (fixing) bolts. The fixing bolts
are M20 8.8 bolts according DIN 931, or equivalent. The two Ø23 H7/m6 fitted bolts are located
closest to the flywheel, one on each side of the engine. The fitted bolts must be designed and
installed so that a sufficient guiding length in the seating top plate is achieved, if necessary
by installing a distance sleeve between the seating top plate and the lower nut. The guiding
length in the seating top plate should be at least equal to the bolt diameter. The fitted bolts
should be made from a high strength steel, e.g. 42CrMo4 or similar and the bolt should have
a reduced shank diameter above the guiding part in order to ensure a proper elongation. The
recommended shank diameter for the fitted bolts is 17 mm.
The tensile stress in the bolts is allowed to be max. 80% of the material yield strength and the
equivalent stress during tightening should not exceed 90% of the yield strength.
Lateral supports must be installed for all engines. One pair of supports should be located at
the free end and one pair (at least) near the middle of the engine. The lateral supports are to
be welded to the seating top plate before fitting the chocks. The wedges in the supports are
to be installed without clearance, when the engine has reached normal operating temperature.
The wedges are then to be secured in position with welds. An acceptable contact surface
must be obtained on the wedges of the supports.
DAAB605808 15-1
15. Foundation Wärtsilä 20 Product Guide
15.2.1.1 Resin chocks

The recommended dimensions of resin chocks are 150 x 400 mm. The total surface pressure
on the resin must not exceed the maximum value, which is determined by the type of resin
and the requirements of the classification society. It is recommended to select a resin that
has a type approval from the relevant classification society for a total surface pressure of 5
N/mm2. (A typical conservative value is ptot 3.5 N/mm2).
During normal conditions, the support face of the engine feet has a maximum temperature of
about 75°C, which should be considered when selecting the type of resin.
The bolts must be made as tensile bolts with a reduced shank diameter to ensure sufficient
elongation since the bolt force is limited by the permissible surface pressure on the resin. For
a given bolt diameter the permissible bolt tension is limited either by the strength of the bolt
material (max. stress 80% of the yield strength), or by the maximum permissible surface
pressure on the resin.
15.2.1.2 Steel chocks

The top plates of the foundation girders are to be inclined outwards with regard to the centre
line of the engine. The inclination of the supporting surface should be 1/100 and it should be
machined so that a contact surface of at least 75% is obtained against the chocks.
Recommended size of the chocks are 115 x 170 mm at the position of the fitted bolts (2 pieces)
and 115 x 190 mm at the position of the fixing bolts (6 pieces). The design should be such
that the chocks can be removed, when the lateral supports are welded to the foundation and
the engine is supported by the jacking screws. The chocks should have an inclination of 1:100
(inwards with regard to the engine centre line). The cut out in the chocks for the fixing bolts
shall be 24...26 mm (M20 bolts), while the hole in the chocks for the fitted bolts shall be drilled
and reamed to the correct size (ø23 H7) when the engine is finally aligned to the reduction
gear.
The design of the holding down bolts is shown in figure Chocking of main engines (V69A0238C).
The bolts are designed as tensile bolts with a reduced shank diameter to achieve a large
elongation, which improves the safety against loosening of the nuts.
15.2.1.3 Steel chocks with adjustable height

As an alternative to resin chocks or conventional steel chocks it is also permitted to install the
engine on adjustable steel chocks. The chock height is adjustable between 30...50 mm for
the approved type of chock. There must be a chock of adequate size at the position of each
holding down bolt.
15-2 DAAB605808
Fig 15-1 Main engine seating, view from above (DAAE017514a)
Engine Dimensions [mm]
A B C D E F G H L Z
W 4L20 50 160 460 590 930 1060 1360 1470 1480 155
W 6L20 50 160 460 590 1530 1660 1960 2070 2080 155
W 8L20 50 160 460 590 1830 1960 2260 2370 2680 155
W 9L20 50 160 460 590 2130 2260 2560 2670 2980 155
Engine (D) Deep sump (D) Wet sump (D) Dry sump
type [mm] [mm] [mm]
4L - 400 -
6L 500 300 300
8L 500 300 300
9L 500 300 300
Fig 15-2 Main engine seating, end

view (DAAE017514a)
DAAB605808 15-3
Fig 15-3 Chocking of main engines (V69A0238C)
15-4 DAAB605808
15.2.2 Resilient mounting

In order to reduce vibrations and structure borne noise, main engines can be resiliently mounted
on rubber mounts. The transmission of forces emitted by a resiliently mounted engine is
10-20% compared to a rigidly mounted engine.
For resiliently mounted engines a speed range of 750-1000 rpm is generally available.
Conical rubber mounts are used in the normal mounting arrangement and additional buffers
are thus not required. A different mounting arrangement can be required for wider speed
ranges (e.g. FPP installations).
Resilient mounting is not available for W 4L20 engines.
Engine (D) Deep sump (D) Wet sump (D) Dry sump
type [mm] [mm] [mm]
6L 825 625 625
8L 825 625 625
9L 825 625 625
Fig 15-4 Resilient mounting

(DAAE003263A)
DAAB605808 15-5
15.3 Mounting of generating sets

15.3.1 Generator feet design
Fig 15-5 Instructions for designing the feet of the generator and the distance between
its holding down bolt (V92F0134E)
15.3.2 Resilient mounting

Generating sets, comprising engine and generator mounted on a common base frame, are
usually installed on resilient mounts on the foundation in the ship.
The resilient mounts reduce the structure borne noise transmitted to the ship and also serve
to protect the generating set bearings from possible fretting caused by hull vibration.
The number of mounts and their location is calculated to avoid resonance with excitations
from the generating set engine, the main engine and the propeller.
15-6 DAAB605808
NOTE
To avoid induced oscillation of the generating set, the following data must be sent
by the shipyard to Wärtsilä at the design stage:
● main engine speed [rpm] and number of cylinders
● propeller shaft speed [rpm] and number of propeller blades
The selected number of mounts and their final position is shown in the generating set drawing.
Fig 15-6 Recommended design of the generating set seating (V46L0720G)
Engine type A* B*
4L 1330 / 1480 1580 / 1730
6L 1330 / 1480 / 1630 1580 / 1730 / 1880
8L 1480 / 1630 1730 / 1880
9L 1480 / 1630 / 1860 1730 / 1880 / 2110
* Dependent on generator width
15.3.3 Rubber mounts

The generating set is mounted on conical resilient mounts, which are designed to withstand
both compression and shear loads. In addition the mounts are equipped with an internal buffer
to limit movements of the generating set due to ship motions. Hence, no additional side or
end buffers are required.
The rubber in the mounts is natural rubber and it must therefore be protected from oil, oily
water and fuel.
The mounts should be evenly loaded, when the generating set is resting on the mounts. The
maximum permissible variation in compression between mounts is 2.0 mm. If necessary,
chocks or shims should be used to compensate for local tolerances. Only one shim is permitted
under each mount.
The transmission of forces emitted by the engine is 10-20% when using conical mounts.
DAAB605808 15-7
Fig 15-7 Rubber mounts (V46L0706C)
15.4 Flexible pipe connections

When the engine or the generating set is resiliently installed, all connections must be flexible
and no grating nor ladders may be fixed to the generating set. When installing the flexible pipe
connections, unnecessary bending or stretching should be avoided. The external pipe must
be precisely aligned to the fitting or flange on the engine. It is very important that the pipe
clamps for the pipe outside the flexible connection must be very rigid and welded to the steel
structure of the foundation to prevent vibrations, which could damage the flexible connection.
15-8 DAAB605808
Wärtsilä 20 Product Guide 16. Vibration and Noise
16. Vibration and Noise

Generating sets comply with vibration levels according to ISO 8528-9. Main engines comply
with vibration levels according to ISO 10816-6 Class 5.
16.1 External forces & couples

Some cylinder configurations produce external forces and couples. These are listed in the
tables below.
The ship designer should avoid natural frequencies of decks, bulkheads and superstructures
close to the excitation frequencies. The double bottom should be stiff enough to avoid
resonances especially with the rolling frequencies.
Fig 16-1 External forces & couples
External forces
Fz = 0, Fy = 0 for all others than 4 and 8 cylinder engines.
Table 16-1 External forces
Engine Speed Freq. Fy Freq. Fz

[RPM] [Hz] [kN] [Hz] [kN]
4L20 900 30 -- 30 --
60 -- 60 1
-- -- -- --
1000 33.3 -- 33.3 --
67 -- 67 1
-- -- -- --
DAAB605808 16-1
16. Vibration and Noise Wärtsilä 20 Product Guide
Engine Speed Freq. Fy Freq. Fz

[RPM] [Hz] [kN] [Hz] [kN]
8L20 900 60 -- 60 2
-- -- -- --
-- -- -- --
1000 67 -- 67 3
-- -- -- --
-- -- -- --
1200 80 -- 80 4
-- -- -- --
-- -- -- --
-- couples and forces = zero or insignificant.
16-2 DAAB605808
External couples
Mz = 0, My = 0 for all others than 9 cylinder engines.
Table 16-2 External couples
Engine Speed Freq. My Freq. Mz

[RPM] [Hz] [kNm] [Hz] [kNm]
9L20 720 12 4.4 12 4.4
24 3 -- --
48 0.3 -- --
750 12.5 4.7 12.5 4.7
25 3.3 -- --
50 0.3 -- --
900 15 7.0 15 7.0
30 4.8 -- --
60 0.4 -- --
1000 17 8 17 8
33 6 33 --
67 1 67 --
1200 20 12 20 12
40 8 40 --
80 1 80 --
DAAB605808 16-3
Table 16-3 Torque variations at 100% load
Engine Speed Freq. MX Freq. MX Freq. MX

[RPM] [Hz] [kNm] [Hz] [kNm] [Hz] [kNm]
4L20 900 30 9.9 60 9.8 90 3.5
1000 33.3 6.6 67 9.6 100 3.5
6L20 900 45 15.4 90 5.2 135 0.4
1000 50 10 100 5 150 1
1200 60 6 120 5 180 1
8L20 900 60 19.6 120 1.5 180 0.5
1000 67 17 133 2 -- --
1200 80 16 160 2 -- --
9L20 900 67.5 17.8 135 0.6 203 0.4
1000 75 16 150 1 -- --
1200 90 16 180 1 -- --

900 rpm, 185 kW/cyl
1000 rpm, 200 kW/cyl
1200 rpm, 220 kW/cyl
Table 16-4 Torque variations at 0% load
Engine Speed Freq. MX Freq. MX Freq. MX

[RPM] [Hz] [kNm] [Hz] [kNm] [Hz] [kNm]
4L20 720 24 4.8 48 1.6 72 0.8
750 25 5.6 50 1.5 75 0.8
900 30 10 60 1.4 90 0.9
1000 33.3 13 66.7 1.3 100 0.9
6L20 720 36 1.4 72 1.2 108 0.3
750 37.5 1.9 75 1.2 112.5 0.3
900 45 4.7 90 1.3 135 0.4
1000 50 6 100 1 150 --
1200 60 11 120 1 180 --
8L20 720 48 3.1 96 0.7 -- --
750 50 3.1 100 0.7 -- --
900 60 2.8 120 0.7 -- --
1000 67 3 133 1 -- --
1200 80 2 160 1 -- --
9L20 720 54 3.5 108 0.5 -- --
750 56.3 3.5 112.5 0.5 -- --
900 67.5 3.6 135 0.5 -- --
1000 75 4 150 1 -- --
1200 90 4 180 1 -- --
16-4 DAAB605808
16.2 Mass moments of inertia

The mass-moments of inertia of the propulsion engines (including flywheel, coupling outer
part and damper) are typically as follows:
Engine J [kgm²]
W 4L20 90...120
W 6L20 90...150
W 8L20 110...160
W 9L20 100...170
16.3 Structure borne noise

Typical structure borne noise levels above and below the resilient mounts are presented as
vibration velocity in dB, reference 1x10-6 mm/s, per octave band.
Fig 16-2 Main engines, typical structure borne noise levels above and below resilient
mounts (DAAB814306)
Fig 16-3 Generating sets, typical structure borne noise levels above and below resilient
mounts (DBAB120103)
DAAB605808 16-5
16.4 Air borne noise

The airborne noise of the engines is measured as sound power level based on ISO 9614-2.
The results represent typical engine A-weighted sound power level at full load and nominal
speed.
Table 16-5 W20 Engine A-weighted Sound Power Level in Octave Frequency Band [dB,
ref. 1pW]
[Hz] 125 250 500 1000 2000 4000 8000 Total
8L 84 98 109 111 111 115 105 118
9L 97 106 110 113 113 116 111 120
Table 16-6 W20_1200rpm Engine A-weighted Sound Power Level in Octave Frequency
Band [dB, ref. 1pW]
[Hz] 125 250 500 1000 2000 4000 8000 Total
6L 91 100 110 115 115 112 107 120
8L 86 99 109 114 113 115 106 120
9L 99 106 111 114 114 116 112 121
16-6 DAAB605808
16.5 Exhaust noise

The results represent typical exhaust sound power level emitted from turbocharger outlet to
free field at engine full load and nominal speed.
Table 16-7 W20 Free Field Exhaust Gas Sound Power Level in Octave Frequency Band
[dB, ref. 1pW]
[Hz] 32 63 125 250 500 1000 2000 4000 Total
8L 135 141 143 135 137 122 118 112 146
9L 142 152 151 141 132 122 116 114 155
Table 16-8 W20_1200rpm Free Field Exhaust Gas Sound Power Level in Octave
Frequency Band [dB, ref. 1pW]
[Hz] 32 63 125 250 500 1000 2000 4000 Total
6L 135 146 146 145 147 129 121 113 152
8L 135 142 143 136 139 122 118 112 147
9L 142 152 151 141 132 123 116 114 155
DAAB605808 16-7
Wärtsilä 20 Product Guide 17. Power Transmission
17. Power Transmission
17.1 Flexible coupling

The power transmission of propulsion engines is accomplished through a flexible coupling or
a combined flexible coupling and clutch mounted on the flywheel. The crankshaft is equipped
with an additional shield bearing at the flywheel end. Therefore also a rather heavy coupling
can be mounted on the flywheel without intermediate bearings.
The type of flexible coupling to be used has to be decided separately in each case on the
basis of the torsional vibration calculations.
In case of two bearing type generator installations a flexible coupling between the engine and
the generator is required.
17.1.1 Connection to generator
Fig 17-1 Connection engine/single bearing generator (V64L0071B)
DAAB605808 17-1
17. Power Transmission Wärtsilä 20 Product Guide
Fig 17-2 Connection engine/two-bearing generator (V64F0001C)
Dimensions [mm]
Engine
D1 L K min D
W 4L20 120 150 140 130
W 6L20 150 190 180 160
W 8L20 150 190 180 160
W 9L20 150 190 180 160
17.2 Clutch
In many installations the propeller shaft can be separated from the diesel engine using a clutch.
The use of multiple plate hydraulically actuated clutches built into the reduction gear is
recommended.
A clutch is required when two or more engines are connected to the same driven machinery
such as a reduction gear.
To permit maintenance of a stopped engine clutches must be installed in twin screw vessels
which can operate on one shaft line only.
17.3 Shaft locking device

A shaft locking device should also be fitted to be able to secure the propeller shaft in position
so that wind milling is avoided. This is necessary because even an open hydraulic clutch can
transmit some torque. Wind milling at a low propeller speed (<10 rpm) can due to poor
lubrication cause excessive wear of the bearings.
The shaft locking device can be either a bracket and key or an easier to use brake disc with
calipers. In both cases a stiff and strong support to the ship’s construction must be provided.
To permit maintenance of a stopped engine clutches must be installed in twin screw vessels
which can operate on one shaft line only. A shaft locking device should also be fitted to be
able to secure the propeller shaft in position so that wind milling is avoided. This is necessary
because even an open hydraulic clutch can transmit some torque. Wind milling at a low
propeller speed (<10 rpm) can due to poor lubrication cause excessive wear of the bearings.
The shaft locking device can be either a bracket and key or an easier to use brake disc with
calipers. In both cases a stiff and strong support to the ship’s construction must be provided.
17-2 DAAB605808
Fig 17-3 Shaft locking device and brake disc with calipers
17.4 Power-take-off from the free end

At the free end a shaft connection as a power take off can be provided. If required full output
can be taken from the PTO shaft.
Fig 17-4 PTO alternative 1 Fig 17-5 PTO alternative 2 (DAAE079045)

(DAAE079074A)
Rating [kW] Dimensions [mm] Rating [kW] 1) Dimensions [mm]
D1 A D1 D2 A B C E F
700 1) 80 105 1700 1) 100 170 610 860 970 280 108
2300 1) 120 150 2200 1) 110 185 630 880 990 300 118
Rating is dependent on coupling hub. Max. output may External support bearing is not possible for resiliently mounted engines.
also be restricted due to max coupling weight 135 kg.
1320 kW always accepted.
1) PTO shaft design rating, engine output may be lower
DAAB605808 17-3
17. Power Transmission Wärtsilä 20 Product Guide
17.5 Input data for torsional vibration calculations

A torsional vibration calculation is made for each installation. For this purpose exact data of
all components included in the shaft system are required. See list below.
Installation
● Classification
● Ice class
● Operating modes
Reduction gear
A mass elastic diagram showing:
● All clutching possibilities
● Sense of rotation of all shafts
● Dimensions of all shafts
● Mass moment of inertia of all rotating parts including shafts and flanges
● Torsional stiffness of shafts between rotating masses
● Material of shafts including tensile strength and modulus of rigidity
● Gear ratios
● Drawing number of the diagram
Propeller and shafting
A mass-elastic diagram or propeller shaft drawing showing:
● Mass moment of inertia of all rotating parts including the rotating part of the OD-box, SKF
couplings and rotating parts of the bearings
● Mass moment of inertia of the propeller at full/zero pitch in water
● Torsional stiffness or dimensions of the shaft
● Material of the shaft including tensile strength and modulus of rigidity
● Drawing number of the diagram or drawing
Main generator or shaft generator
A mass-elastic diagram or an generator shaft drawing showing:
● Generator output, speed and sense of rotation
● Mass moment of inertia of all rotating parts or a total inertia value of the rotor, including
the shaft
● Torsional stiffness or dimensions of the shaft
● Material of the shaft including tensile strength and modulus of rigidity
● Drawing number of the diagram or drawing
Flexible coupling/clutch
If a certain make of flexible coupling has to be used, the following data of it must be informed:
● Mass moment of inertia of all parts of the coupling
● Number of flexible elements
● Linear, progressive or degressive torsional stiffness per element
● Dynamic magnification or relative damping
● Nominal torque, permissible vibratory torque and permissible power loss
17-4 DAAB605808
● Drawing of the coupling showing make, type and drawing number

Operational data
● Operational profile (load distribution over time)
● Clutch-in speed
● Power distribution between the different users
● Power speed curve of the load
17.6 Turning gear

The engine can be turned with a manual ratchet tool after engaging a gear wheel on the flywheel
gear rim. The ratchet tool is provided with the engine.
DAAB605808 17-5
Wärtsilä 20 Product Guide 18. Engine Room Layout
18. Engine Room Layout
18.1 Crankshaft distances

Minimum crankshaft distances have to be followed in order to provide sufficient space between
engines for maintenance and operation.
18.1.1 Main engines
Fig 18-1 Crankshaft distances main engines (DAAF017589)
Engine A B C D
W 4L20 or W 1800 1000 1200 1845

6L20
W 8L20 1800 1300 1200 1845
W 9L20 1800 1300 1200 1845
All dimensions in mm.
A - Minimum height when removing a piston
DAAB605808 18-1
18. Engine Room Layout Wärtsilä 20 Product Guide
B - Camshaft overhaul distance
C - Charge air cooler overhaul distance
D - Space necessary for access to the connection box
18.1.2 Generating sets
Fig 18-2 Crankshaft distances generating sets (DAAE007434D)
Table 18-1 Standard genset
Engine type E* F
W 4L20 1970 / 2040 1270 / 1420
W 6L20 1970 / 2040 / 2170 1270 / 1420 / 1570
W 8L20 2040 / 2170 / 2250 1420 / 1570 / 1700
W 9L20 2040 / 2200 / 2400 1420 / 1570 / 1700
Table 18-2 Double flexible installed genset
Engine type E* F
W 4L20 2450 1350
W 6L20 2450 1350
W 8L20 2450 1350
W 9L20 2450 1350
E = MIN. DISTANCE BETWEEN ENGINES DEPENDENT ON COMMON BASE PLATE

F = WIDTH OF THE COMMON BASE PLATE DEPENDENT ON WIDTH OF THE ALTERNATOR
* In case of extra wide lifting lugs needed, 230mm should be added to dimension E. Depending on final
generator selection
* Dimension E should be checked at all times with each project specific configuration due to generator
service space
All dimensions in mm.
18-2 DAAB605808
18.2 Space requirements for maintenance

18.2.1 Working space reservation
It is recommended to reserve about one meter of free working space.
No obstructions should be built in way of:
● Crankcase and camshaft covers
● Camshaft withdrawal space
● Engine driven pump service space
● Charge air cooler withdrawal space
● Piston overhauling height
● Turbocharger maintenance space
● Electrical junction box door
Free route for hauling parts to and from engine to be foreseen.
See chapter "Transport Dimensions and Weights" for dimensions of maintenance items.
18.2.2 Lifting equipment

It is essential for efficient and safe working conditions that the lifting equipment are applicable
for the job and they are correctly dimensioned and located.
The required engine room height depends on space reservation of the lifting equipment and
also on the lifting and transportation arrangement. The minimum engine room height can be
achieved if there is enough transversal and longitudinal space, so that there is no need to
transport parts over insulation box or rocker covers.
Separate lifting arrangement for overhauling turbocharger is required (unless overhead travelling
crane, which also covers the turbocharger is used). Turbocharger lifting arrangement is usually
best handled with a chain block on a rail located above the turbocharger axis.
18.2.3 Maintenance platforms

In order to enable efficient maintenance work on the engine, it is advised to build the
maintenance platforms on recommended elevations. The width of the platforms should be at
minimum 800 mm to allow adequate working space. The surface of maintenance platforms
should be of non-slippery material (grating or chequer plate).
NOTE
Working Platforms should be designed and positioned to prevent personnel slipping,
tripping or falling on or between the walkways and the engine
18.3 Transportation and storage of spare parts and tools

Transportation arrangement from engine room to storage and workshop has to be prepared
for heavy engine components. This can be done with several chain blocks on rails or
alternatively utilising pallet truck or trolley. If transportation must be carried out using several
lifting equipment, coverage areas of adjacent cranes should be as close as possible to each
other.
Engine room maintenance hatch has to be large enough to allow transportation of main
components to/from engine room.
DAAB605808 18-3
It is recommended to store heavy engine components on slightly elevated adaptable surface

e.g. wooden pallets. All engine spare parts should be protected from corrosion and excessive
vibration.
On single main engine (SME) installations it is important to store heavy engine parts close to
the engine to make overhaul as quick as possible in an emergency situation.
18.4 Required deck area for service work

During engine overhaul some deck area is required for cleaning and storing dismantled
components. Size of the service area is dependent of the overhauling strategy chosen, e.g.
one cylinder at a time, one bank at a time or the whole engine at a time. Service area should
be plain steel deck dimensioned to carry the weight of engine parts.
18.4.1 Service space requirement

18.4.1.1 Service space for engines with turbocharger in driving end
Fig 18-3 Service space for engines with turbocharger in driving end (V69C0301E)
Service spaces in mm 6L 8L 9L
A1 Height for overhauling piston and connecting rod 1800
A2 Height for transporting piston and connecting rod freely over adja- 2300
cent cylinder head covers
A3 Height for transporting piston and connecting rod freely over ex- 2300 2400 2400
haust gas insulation box
B1 Width for dismantling charge air cooler and air inlet box 1200
B2 Width for dismantling charge air cooler and air inlet box sideways 1310
by using lifting tool
B3 Height of the lifting eye for the charge air cooler lifting tool 1600
B4 Recommended lifting point for charge air cooler lifting tool 390
18-4 DAAB605808
Service spaces in mm 6L 8L 9L
C1 Removal of main bearing side screw, flexible / rigid mounting 800 / 560
D1 Distance needed for dismantling lubricating oil and water pumps 635
E1 Distance needed for dismantling pump cover with fitted pumps With PTO: lenght + 515
Without PTO: 650
E2 Height of lifting eye for the pump cover with fitted pumps, with 750 / 2770
lifting tool 1/ alternative lifting tool 2
F1 The recommended axial clearance for dismantling and assembly 650 710 710
of silencers
F2 Minimum axial clearance 100
F3 Recommended distance for dismantling the gas outlet elbow 990 1170 1170
G1 Recommended lifting point for the turbocharger 300
G2 Recommended lifting point sideways for the turbocharger 345
H1 Width for dismantling lubricating oil module and/or plate cooler 1250
H2 Width for dismantling lubricating oil module with lifting tool 1380
H3 Recommended lifting point for dismantling lubricating oil module 445

and/or plate cooler
H4 Recommended lifting point sideways for dismantling lube oil 1045
module and/or plate cooler
H5 Height of lifting eye for dismantling lube oil module with lifting tool 1675
I1 Camshaft overhaul distance (free end) 1000 1300 1300
I2 Camshaft overhaul distance (flywheel end) 1000 1300 1300
J3 Space necessary for access to connecting box 2150
18.4.1.2 Service space for engines with turbocharger in free end
Fig 18-4 Service space for engines with turbocharger in free end (V69C0302F)
DAAB605808 18-5
Service spaces in mm 4L 6L 8L 9L
A2 Height for transporting piston and connecting rod freely over 2300
adjacent cylinder head covers
A3 Height for transporting piston and connecting rod freely over 2230 2300 2400 2400
exhaust gas insulation box
A4 Height needed for transporting piston and connecting rod freely - - - 2720
over 60°C exhaust gas insulation box (SOLAS)
B2 Width for dismantling charge air cooler and air inlet box side- 1310
ways by using lifting tool
B4 Recommended lifting point for charge air cooler lifting tool 260 550
C1 Removal of main bearing side screw, flexible / rigid mounting 800 / 560
E1 Distance needed for dismantling pump cover with fitted pumps With PTO: lenght + 515
Without PTO: 650
E2 Height of the lifting eye for the pump cover with fitted pumps, 750 / 2770
with lifting tool 1/ alternative lifting tool 2
F1 The recommended axial clearance for dismantling and assembly 590 650 750 750
of silencers
F3 Recommended distance for dismantling the gas outlet elbow 890 990 1120 1120

and/or plate cooler
H5 Height of lifting eye for dismantling lube oil module with lifting 1675
tool
I1 Camshaft overhaul distance (free end) 700 1000 1300 1300
I2 Camshaft overhaul distance (flywheel end) 700 1000 1300 1300
18-6 DAAB605808
18.4.1.3 Service space for generating sets
Fig 18-5 Service space for generating sets (DAAE006367E)
A2 Height for transporting piston and connecting rod freely over 2300
adjacent cylinder head covers
A3 Height for transporting piston and connecting rod freely over 2230 2300 2400 2400
exhaust gas insulation box
A4 Height needed for transporting piston and connecting rod freely - - - 2720
over 60°C exhaust gas insulation box (SOLAS)
B2 Width for dismantling charge air cooler and air inlet box side- 1310
ways by using lifting tool
B4 Recommended lifting point for charge air cooler lifting tool 260 550
C1 width for removing main bearing side screw 560
E1 Distance needed for dismantling pump cover with fitted pumps 650
E2 Height of the lifting eye for the pump cover with fitted pumps, 750 / 2770
with lifting tool 1/ alternative lifting tool 2
F1 The recommended axial clearance for dismantling and assembly 590 650 750 750
of silencers
F3 Recommended distance for dismantling the gas outlet elbow 890 990 1120 1120
DAAB605808 18-7

and/or plate cooler
H5 Height of lifting eye for dismantling lube oil module with lifting 1670
tool
I1 Camshaft overhaul distance (free end) 700 1000 1300 1300
I2 Camshaft overhaul distance (flywheel end) 700 1000 1300 1300
K1 Service space for generator 500
18-8 DAAB605808
Wärtsilä 20 Product Guide 19. Transport Dimensions and Weights
19. Transport Dimensions and Weights
19.1 Lifting of engines
Fig 19-1 Lifting of main engines (V83D0285C)
Dry sump Wet sump

Engine L [mm]
A [mm] B [mm] A [mm] B [mm]
W 4L20 2600 725 600 725 600
W 6L20 3200 624 600 824 675
W 8L20 3500 624 600 824 675
W 9L20 4100 624 600 824 675
DAAB605808 19-1
19. Transport Dimensions and Weights Wärtsilä 20 Product Guide
NOTE
Maximum load 30 tonnes.
Fig 19-2 Lifting of generating sets (V83D0300D)
19-2 DAAB605808
Wärtsilä 20 Product Guide 19. Transport Dimensions and Weights
19.2 Engine components

19.2.1 Turbocharger and cooler inserts (DAAE031768C)
Turbocharger Charge air cooler
Engine A* [mm] B* [mm] C* [mm] Weight* [kg] D [mm] E [mm] G [mm] Weight [kg]
900,1000 /
1200rpm
W4L20 936 536 490 160 568 340 285 126 / -
W6L20 1096 603 546 293 578 380 345 152 / 140
W8L20 1357 716 666 368 578 380 345 156 / 150
W9L20 1357 716 666 370 578 380 345 159 / 150
Lubricating oil cooler insert

Engine
H [mm] J [mm] L [mm] Weight [kg]
W4L20 109 694 304 53
W6L20 150 694 304 64
W8L20 201 694 304 77
W9L20 238 694 304 87
NOTE
* Max. dimension/ weight.
DAAB605808 19-3
19. Transport Dimensions and Weights Wärtsilä 20 Product Guide
19.2.2 Major spare parts (V92L1275A)
Item Weight (kg) Item Weight (kg)
1 Connecting rod 39 7 Injection pump 27
2 Piston 21 8 Injection valve 3.2
3 Cylinder liner 41 9 Main bearing shell 1.4
4 Cylinder head 94 10 Smaller intermediate gear 11.4
5 Valve 0.8 11 Bigger intermediate gear 23.5
6 Piston ring 0.2 12 Camshaft drive gear 25
19-4 DAAB605808
Wärtsilä 20 Product Guide 20. Product Guide Attachments
20. Product Guide Attachments

This and all other product guides can be accessed on the internet, at www.wartsila.com.
Product guides are available both in web and PDF format. Engine outline drawings are available
not only in 2D drawings (in PDF, DXF format), but also in 3D models in near future. Please
consult your sales contact at Wärtsilä for more information.
Engine outline drawings are not available in the printed version of this product guide.
DAAB605808 20-1
Wärtsilä 20 Product Guide 21. ANNEX
21. ANNEX
21.1 Unit conversion tables

The tables below will help you to convert units used in this product guide to other units. Where
the conversion factor is not accurate a suitable number of decimals have been used.
Length conversion factors Mass conversion factors

Convert from To Multiply by Convert from To Multiply by
mm in 0.0394 kg lb 2.205
mm ft 0.00328 kg oz 35.274
Pressure conversion factors Volume conversion factors

kPa psi (lbf/in2) 0.145 m3 in3 61023.744
kPa lbf/ft2 20.885 m3 ft3 35.315
kPa inch H2O 4.015 m3 Imperial gallon 219.969
kPa foot H2O 0.335 m3 US gallon 264.172
kPa mm H2O 101.972 m3 l (litre) 1000
kPa bar 0.01
Power conversion Moment of inertia and torque conversion factors

kW hp (metric) 1.360 kgm2 lbft2 23.730
kW US hp 1.341 kNm lbf ft 737.562
Fuel consumption conversion factors Flow conversion factors

g/kWh g/hph 0.736 m3/h (liquid) US gallon/min 4.403
g/kWh lb/hph 0.00162 m3/h (gas) ft3/min 0.586
Temperature conversion factors Density conversion factors

°C F F = 9/5 *C + 32 kg/m3 lb/US gallon 0.00834
°C K K = C + 273.15 kg/m3 lb/Imperial gallon 0.01002
kg/m3 lb/ft3 0.0624
21.1.1 Prefix
Table 21-1 The most common prefix multipliers
Name Symbol Factor Name Symbol Factor Name Symbol Factor

tera T 1012 kilo k 103 nano n 10-9
giga G 109 milli m 10-3
mega M 106 micro μ 10-6
DAAB605808 21-1
21. ANNEX Wärtsilä 20 Product Guide
21.2 Collection of drawing symbols used in drawings
Fig 21-1 List of symbols (DAAF406507 - 1)
21-2 DAAB605808
DAAB605808 21-3
21. ANNEX Wärtsilä 20 Product Guide
21-4 DAAB605808
DAAB605808 21-5
Wärtsilä is a global leader in complete lifecycle power solutions
for the marine and energy markets. By emphasising technological
innovation and total efficiency, Wärtsilä maximises the
environmental and economic performance of the vessels and
power plants of its customers.
www.wartsila.com

Product Guide o e w20

Uploaded by

Copyright:

Available Formats

Product Guide o e w20

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Guide o e w20

Uploaded by

Copyright:

Available Formats

Wärtsilä 20

Issue Published Updates

1/2015 14.10.2015 Numerous updates throughout the product guide

Wärtsilä, Marine Solutions

Vaasa, July 2019

2. Operating Ranges .................................................................................................................................... 2-1

3. Technical Data .......................................................................................................................................... 3-1

4. Description of the Engine ........................................................................................................................ 4-1

5. Piping Design, Treatment and Installation ............................................................................................. 5-1

6. Fuel Oil System ......................................................................................................................................... 6-1

7. Lubricating Oil System ............................................................................................................................ 7-1

8. Compressed Air System .......................................................................................................................... 8-1

8.2 External compressed air system .......................................................................................................... 8-4

9. Cooling Water System ............................................................................................................................. 9-1

10. Combustion Air System ......................................................................................................................... 10-1

11. Exhaust Gas System .............................................................................................................................. 11-1

12. Turbocharger Cleaning .......................................................................................................................... 12-1

13. Exhaust Emissions ................................................................................................................................. 13-1

14. Automation System ................................................................................................................................ 14-1

15. Foundation .............................................................................................................................................. 15-1

16. Vibration and Noise ................................................................................................................................ 16-1

17. Power Transmission ............................................................................................................................... 17-1

18. Engine Room Layout .............................................................................................................................. 18-1

19. Transport Dimensions and Weights ..................................................................................................... 19-1

20. Product Guide Attachments .................................................................................................................. 20-1

21. ANNEX ..................................................................................................................................................... 21-1

1. Main Data and Outputs

1.1 Technical main data

Cylinder bore ........................................ 200 mm

Stroke .................................................... 280 mm

Piston displacement ............................. 8.8 l/cyl

Number of valves .................................. 2 inlet valves and 2 exhaust valves

Cylinder configuration ........................... 4, 6, 8, 9, in-line

Direction of rotation .............................. Clockwise, counterclockwise on request

Speed .................................................... 900, 1000, 1200 rpm

Mean piston speed ............................... 8.4, 9.3, 11,2 m/s

1.2 Maximum continuous output

1.2.1.1 Diesel electric propulsion, constant speed

Table 1-1 Output tables (kW)

Engine 1200 rpm 1000 rpm 900 rpm

4L20 - 800 740

6L20 1320 1200 1110

8L20 1760 1600 1480

9L20 1980 1800 1665

1.2.1.2 Mechanical controllable pitch propeller propulsion, variable

Table 1-2 Output tables (kW)

Engine 1200 rpm 1000 rpm

6L20 1320 1200

Engine 1200 rpm 1000 rpm

8L20 1760 1600

9L20 1980 1600

1.2.2 Rated Output - Auxiliary Engines

Engine 1200 rpm 1000 rpm 900 rpm

4L20 - 800 740

6L20 1320 1200 1110

8L20 1760 1600 1480

9L20 1980 1800 1665

Pe = Mean effective pressure [bar]

P = Output per cylinder [kW]

n = Engine speed [r/min]