Slump Test

Concrete slump test or slump cone test is to determine the workability
or consistency of concrete mix prepared at the laboratory or the construction

site during the progress of the work. Concrete slump test is carried out from
batch to batch to check the uniform quality of concrete during construction.
The slump test is the most simple workability test for concrete, involves low
cost and provides immediate results. Due to this fact, it has been widely
used for workability tests since 1922. The slump is carried out as per
procedures mentioned in ASTM C143 in the United States, IS: 1199 – 1959 in
India and EN 12350-2 in Europe.
Generally concrete slump value is used to find the workability, which
indicates water-cement ratio, but there are various factors including
properties of materials, mixing methods, dosage, admixtures etc. also affect
the concrete slump value.
Table of Contents
 Factors which influence the concrete slump test:
 Equipments Required for Concrete Slump Test
 Sampling of Materials for Slump Test
 Procedure for Concrete Slump Cone Test
 Slump Value Observation:
 Results of Slump Test on Concrete
Factors which influence the concrete slump test:

1. Material properties like chemistry, fineness, particle size distribution,
moisture
content and temperature of cementitious materials. Size, texture, combined
grading, cleanliness and moisture content of the aggregates,
2. Chemical admixtures dosage, type, combination, interaction, sequence of
addition and its effectiveness,
3. Air content of concrete,
4. Concrete batching, mixing and transporting methods and equipment,
5. Temperature of the concrete,
6. Sampling of concrete, slump-testing technique and the condition of test
equipment,
7. The amount of free water in the concrete, and
8. Time since mixing of concrete at the time of testing.
Equipments Required for Concrete Slump Test
Mold for slump test i.e. slump cone, non porous base plate, measuring scale,
temping rod. The mold for the test is in the form of the frustum of a cone
having height 30 cm, bottom diameter 20 cm and top diameter 10 cm. The
tamping rod is of steel 16 mm diameter and 60cm long and rounded at one
end.
Sampling of Materials for Slump Test

A concrete mix (M15 or other) by weight with suitable water/ cement ratio is
prepaid in the laboratory similar to that explained in 5.9 and required for
casting 6 cubes after conducting Slump test.
Figure-1: Measuring Slump of Concrete

Procedure for Concrete Slump Cone Test
1. Clean the internal surface of the mould and apply oil.
2. Place the mould on a smooth horizontal non- porous base plate.
3. Fill the mould with the prepared concrete mix in 4 approximately equal
layers.
4. Tamp each layer with 25 strokes of the rounded end of the tamping rod in a
uniform manner over the cross section of the mould. For the subsequent
layers, the tamping should penetrate into the underlying layer.
5. Remove the excess concrete and level the surface with a trowel.
6. Clean away the mortar or water leaked out between the mould and the base
plate.
7. Raise the mould from the concrete immediately and slowly in vertical
direction.
8. Measure the slump as the difference between the height of the mould and
that of height point of the specimen being tested.
Figure-2: Concrete Slump Test Procedure

NOTE:
The above operation should be carried out at a place free from Vibrations or
shock and within a period of 2 minutes after sampling.
Slump Value Observation:

The slump (Vertical settlement) measured shall be recorded in terms of
millimeters of subsidence of the specimen during the test.
Results of Slump Test on Concrete

Slump for the given sample= _____mm
When the slump test is carried out, following are the shape of the concrete
slump that can be observed:
Figure-3: Types of Concrete Slump Test Results
o True Slump – True slump is the only slump that can be measured in the test.
The measurement is taken between the top of the cone and the top of the
concrete after the cone has been removed as shown in figure-1.
o Zero Slump – Zero slump is the indication of very low water-cement ratio,
which results in dry mixes. These type of concrete is generally used for road
construction.
o Collapsed Slump – This is an indication that the water-cement ratio is too
high, i.e. concrete mix is too wet or it is a high workability mix, for which a
slump test is not appropriate.
o Shear Slump – The shear slump indicates that the result is incomplete, and
concrete to be retested.

Slump Test

Uploaded by

Copyright:

Available Formats

Slump Test

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Slump Test

Uploaded by

Copyright:

Available Formats

Concrete slump test or slump cone test is to determine the workability

or consistency of concrete mix prepared at the laboratory or the construction

Factors which influence the concrete slump test:

Sampling of Materials for Slump Test

Figure-1: Measuring Slump of Concrete

Figure-2: Concrete Slump Test Procedure

Slump Value Observation:

Results of Slump Test on Concrete

You might also like