2010 Safari Land DutyGear Catalog

WE ARE SAFARILAND
BODY ARMOR | DUTY GEAR | Less lethal | HARD ARMOR | PROTECTIVE GEAR
Armor Systems | FIREARMS ACCESSORIES | INVESTIGATION & EXAMINATION
safariland.com
2010 DUTY GEAR PRODUCTS Catalog

DUTY GEAR CATALOG
3120 E. MISSION BLVD. • ONTARIO, California USA 91761

(909) 923-7300 • FAX (909) 923-7400 • (800) 347-1200 (USA ONLY)
safariland.com/dutygear • holsters.com • bianchi-intl.com • bianchicowboy.com
1209 ©2010 Safariland

To ENsure Your Satisfaction
Your product is carefully crafted from the finest materials. For product longevity and your own safety, here are some
commonsense guidelines:
Inspecting Your Product
1. Thoroughly read the safety information in this catalog and other information included with your purchase.
2. Make sure your handgun fits properly, safely and to your satisfaction.
3. Visually inspect your handgun for any defects in material or workmanship.
4. Check the retainer strap, spring or other retaining device and be certain that your handgun is properly and safely secured
for your application.
5. Visually inspect all stitchings, snaps, springs, clips and rivets for looseness, breakage or other damage.
6. Pay special attention to points of strain and critical points, such as belt loops, welts, retainer straps, springs or other
retaining devices.
7. Look for any sign that leather or other materials have become dry or brittle.
8. Should your holster or other product become worn, loose, defective or ill-fitting, cease use immediately.
Care and Storage

Leather
Storage
Store your leather product in a cool, dry place. High humidity can cause mildew, while dry heat and direct sunlight can cause
drying and cracking. If you leave your handgun in the holster or other product, check it daily for moisture, condensation or
corrosion. Changing atmospheric conditions, heavy perspiration and other factors could create such conditions.
Care
Treat the interior of your holster with spray silicone to help protect against excess moisture. Spray silicone also speeds the
draw by reducing friction.
If your product becomes water-soaked, reshape it as best you can and allow it to air-dry at room temperature. Do not use a
hot oven – it will shrink, harden and crack the leather.
Because Bianchi leather is hand finished with our special leather dressing, should your leather product become dry or
scratched, you can treat the exterior with a commercial leather dressing that does not contain lacquer. (Be careful when
using Neat’s foot oil; large amounts will soften the leather.)
Brass cartridges or other brass hardware when stored with leather will acquire a greenish residue called “verdigris.“ It is a
natural product of a chemical reaction between brass and vegetable-tanned leather, and it wipes off. (Using nickel-plated
cartridges in belt loops will avoid this condition.)
SafariLaminate™, AccuMold®, AccuMold® Elite™ and PatrolTek™

Storage
These products have been field-proven to withstand a wide variety of environmental conditions. These products should be
stored in a cool, dry environment when not in use. We do not recommend storing these products in a vehicle trunk or other
areas where extreme heat can exceed the outside environment.
Never store your SafariLaminate products near a heat source that emits high temperatures (200°F), which can deform or
destroy the polymer from which many SafariLaminate products are manufactured. If you have accidentally exposed your
equipment to a heat source you should immediately remove it from the area, allow it to cool to room temperature and then
operate it to ensure correct function.
Cleaning
INNOVATION NOT IMITATION.™ These products are best cleaned with a solution of warm, soapy water and a soft brush. A toothbrush and dish soap work
well. If decontamination is required, an antibacterial soap or 10% solution of household chlorine bleach may be used. After
cleaning, simply rinse off with fresh water and let air-dry. Be sure the product is completely dry inside and out prior to use.
You are holding in your hands a collection of the most time-honored, most When these products are exposed to salt spray or immersed in salt water, it is important to thoroughly rinse them in warm water as
universally praised duty gear anywhere in the world. For decades, the names soon as possible. Never use solvents such as acetone to clean AccuMold products, as this could result in damage to the product.
Safariland and Bianchi have been revered in law enforcement and security circles
like no other brand names. Now united under the Safariland banner, our duty gear
is the overwhelming choice of agencies around the world. And for good reason.
How to Measure Barrel Length
Before you order a holster, please be sure you have the correct barrel measurement for your handgun. This measurement is
As always, we work hard to build on the unique leadership position we have very easy to do, and it will ensure that you get the holster that’s exactly right for your gun.
earned, offering the industry’s most extensive range of top-quality holsters, belts,
accessories, restraints and more. We have combined our renowned legacies of 4" 5"
innovation, quality and customer care to provide genuine one-stop shopping for
every type of duty gear you will need. Today’s Safariland remains totally committed
to serving those who put it all on the line to uphold order and keep the peace.
And nobody does it better.
Semiautomatics – Measure
barrel length from the rear
Revolvers – Measure barrel length from portion of the ejection port to
the face of the cylinder to the muzzle. the muzzle.
TaBLE of coNTENTs
fiNisHEs & TEcHNoLogY
safariland™ Brands & finishes .............................. 2
safariland aLs® intro ............................................... 3
retention Level chart ............................................... 3
Bianchi® Brands & finishes ................................... 4
safariland New Products ........................................ 5
duTY HoLsTErs
safariland duty Holsters ......................................... 6
safariland spacer Kits .......................................... 13
Bianchi duty Holsters ........................................... 14
Edw HoLsTErs
safariland Holsters................................................ 16
duTY BELTs
safariland Belts ..................................................... 22
Bianchi Belts .......................................................... 24
duTY accEssoriEs
safariland sLs accessories ................................ 26
safariland uBL accessories ............................... 27
safariland safariLaminate™ ................................. 28
safariland Nylok® Pro ........................................... 33
Bianchi accuMold® .............................................. 34
Bianchi accuMold® Elite™ ................................... 38
Bianchi PatrolTek™ ................................................ 42
TacTicaL & MiLiTarY

safariland Tactical Holsters ................................ 46
safariland Tactical accessories ........................ 50
safariland gear Bags ............................................ 54
Bianchi Tactical Holsters & accessories ........ 56
QuicK aTTacHMENT sYsTEMs

MLs, QLs, ELs......................................................... 60
rLs /MouNTs
™
safariland rapid Light system ............................ 64

safariland Mounts ................................................. 65
safariLaNd rEsTraiNTs .................... 66

coNcEaLMENT HoLsTErs
safariland Belt slide ............................................. 72
safariland Paddle .................................................. 76
safariland shoulder .............................................. 78
safariland iwB/ankle ........................................... 79
Bianchi Belt slide ................................................. 80
Bianchi Paddle ....................................................... 84
Bianchi iwB............................................................ 85
Bianchi shoulder ................................................... 86
Bianchi Vest concealment................................... 88
Bianchi ankle ......................................................... 89
a MEssagE froM our fouNdEr coNcEaLMENT BELTs & accEssoriEs

It’s been one year since our Power of One message was announced. One safariland Belts & accessories ......................... 90
year since our rebranding brought together some of the strongest Bianchi Belts & accessories............................... 91
companies in our industry under one name: Safariland. This sPorTiNg
decision was not made lightly but was undertaken only after Bianchi Holsters, Belts & cases ......................... 92
considerable feedback from you, our customer. You told us that
Safariland has come to be one of the most recognizable names coMPETiTioN
in the field of law enforcement products. We are humbled that safariland Holsters, Belts & accessories ................... 95
we have grown to gain your trust over the years, and you can Team safariland ................................................................ 98
be assured that we will continue to bring you the highest-quality
and most innovative products for the men and women who BiaNcHi cowBoY....................................... 100
depend on us every day. Together, We Save Lives.
accEssoriEs ................................................... 102
Neale Perkins,
Founder coNsuMEr safETY,
carE & sToragE ............................................. 104
holsters.com • bianchi-intl.com • 800.347.1200 1
safariLaNd ™
BraNd guidE
sTX Tactical
®
A special tactical finish famous for its incredible strength, abrasion resistance and
protective qualities. Heat laminated and molded to the exact shape of weapons and
safariLaminate
™
accessories for better security. Will not absorb water or sweat, dries quickly, and is easily
Our original and most extensive holster and accessory line, SafariLaminate offers a traditional cleaned with mild soap and water or Armor All®. A thin layer of SafariSuede™ in the liner
leather look and feel in a synthetic material. While SafariLaminate is a durable lamination protects the finish of guns and absorbs excess oils or lubricants.
process used to create many of our products, it is best known as the performance gear that law
enforcement professionals recognize as the uniquely famous Safariland line.
sTX Basket weave Nylok Pro

®
We’ve expanded our popular STX Tactical® finish to include plain, hi gloss and our newest Nylok PRO accessories incorporate the SafariLaminate™ process in a special molding
basket weave finish. This hard-shell STX material is heat laminated and molded to the exact process that bonds 1050-denier DuPont® nylon to a noncollapsible shell. The result is
shape of weapons and accessories, and it’s extremely durable. It’s the only product available professional-looking gear that is lightweight, durable and waterproof and resists tears
that addresses seat belt abrasion issues. Will not absorb water or sweat, dries quickly, and and fading. We recommend STX duty holsters for Nylok PRO rigs.
is easily cleaned with mild soap and water or Armor All®. Features a SafariSuede™ liner that
absorbs excess oils and lubricants and helps protect the finish of guns.
safariLaNd ™
BasKET wEaVE
Hi gLoss
PLaiN BLacK
fiNisHEs guidE
Safariland Duty Gear finishes are designed to protect your investment by offering
outstanding durability and appearance year in and year out.
®
NYLoK Pro
NYLoN LooK sTX BasKET wEaVE
sTX Hi gLoss
sTX PLaiN BLacK

sTX TacTicaL
cusToM fiNisHEs
carBoN fiBEr
LooK
cordoVaN
The following custom finishes are also available based on minimum order quantities.
Call customer care for details.
iMPorTaNT NoTE: Individual products may have limited finish or color choices.
2 safariland.com/dutygear
1 The ALS is a unique design that locks into the ejection
port and is operated by the thumb once the SLS is
released.
2 The SLS rotating hood has been tested and proven for
many years on the 6280 and 6004 series of holsters.
Simply push down and rotate forward as you obtain
The ALS® system is the latest evolution in retention holsters and builds upon your shooting grip. To close, pull back on the hood, and
the successful Self Locking System (SLS). With many patents to its credit, the SLS self locks. No snaps or straps to manipulate.
the key to this system is an internal locking device that secures the weapon
in all directions simply upon reholstering. Level III Retention™ is achieved 3 The Hood Guard helps protect the SLS from impact
when used in conjunction with the SLS, which can also be elevated to and premature release, especially in an attempted
Level IV Retention™ with the addition of the Sentry. Also available in Level I takeaway. Included with all duty and tactical versions.
Retention™ versions.
4 Constructed of SafariLaminate™, a thermal-molded
Additionally, holsters with this advanced ergonomic design are completely holster to help protect the handgun and gun mounted
operable with the thumb, making training easy, and the straight-up accessories for years of use.
4
draw makes them very instinctive to use, yet difficult for an assailant’s
attempted takeaway.
And finally, once the retention devices are released, the weapon can be
PATENTED &
drawn straight out of the holster with no twisting or other motion required. PATENT PENDING
3
The ALS series holsters cover a wide array of market needs, from retention
duty holsters to models in our popular tactical offerings to a belt slide, belt
clip and paddle holster for the concealment markets, both with and without
the SLS.
2
6365
6305
6342
6378
1
duTY TacTicaL Edw coNcEaLMENT
rETENTioN
LEVEL cHarT
Safariland’s duty holsters are not only built to
last, they’re designed with weapon retention
and officer safety in mind. However, no industry
standard exists to rate a holster’s ability to
resist weapon takeaway attempts. For that
reason, Safariland has developed a system of
rating a holster’s Retention Level.
Level i Level ii Level iii Level iV Level V
Retention levels are tested with the initiation Retention holsters offer Retention holsters offer Retention holsters offer Retention holsters offer Retention holsters offer
of a “grab and snatch” by an adversary. To Moderate Retention. Enhanced Retention. Optimum Retention. Exceptional Retention. Maximum Retention.
qualify as Level I Retention™, a holster must Shown on page: 6 Shown on page: 8 Shown on page: 10 Shown on page: 12 Shown on page: 12
provide for unlimited direction of force for five 2 295 070 6070 6070*
full seconds. At the end of the five seconds, the 200 2955 0705 6075 6075*
weapon must still be secure in the holster and
the holster must still be attached to the wearer.
2005 6280 6270 6270* 6295* (not shown)
The wearer must be able to accomplish a draw 6320 6285 6275 6275* 62955* (not shown)
after the attack. These tests are then repeated 6325 6280† 6295 (not shown)
with additional safety measures (with previous
safety measure disengaged) to determine
6285† 62955 (not shown)
where a holster falls on the retention spectrum. 6360 6280**
For more information on the Safariland Holster 6365 6285**
Retention system, see our Web site or call 6360*
Customer Care.
6365*
These retention ratings give the holster buyer † Tension screw properly adjusted or with addition of Sentry
a method to quickly determine the relative *With addition of Sentry
Retention Level of different holster models. **Properly adjusted tension screw and with addition of Sentry

BiaNcHi BraNd guidE ®
accuMold Technology
®
A state-of-the-art molded nylon holster constructed and

molded from Bianchi’s trilaminate material, made up
of a ballistic weave outer material, a firm, high-density
closed-cell foam center; and our smooth Coptex™ lining. All
AccuMold gear is designed to precisely fit the gear it was
designed to carry.
accuMold Elite
™
®
We’ve taken our patented AccuMold technology and

dressed it up. The AccuMold Elite line offers the same
construction of AccuMold, but with a Duraskin™ outer
material that looks amazingly like leather. You can’t tell the
difference until you pick it up and see that it’s almost half the
weight of leather!
PatrolTek
™
PatrolTek duty belts and accessories are made using our

molded trilaminate technology but at a price to meet the
demands of ever-tightening budgets. Now you don’t have to
give up function and wear to get duty gear at a great price.
BiaNcHi fiNisHEs BiaNcHi TEcHNoLogY

guidE Pinch retention device – Prd
® ™
Our exclusive PRD is formed of a high strength polymer. When the weapon
accuMoLd PaTroLTEK is firmly seated in the holster, the PRD grips the trigger guard, holding the
weapon in place until you’re ready to draw. PATENTED
ErgoTek duty Belts

™
Bianchi’s ErgoTek™ duty belts redistribute the weight of the duty gear,
Ballistic 600-Denier away from the edges of the belt and over its wide closed-cell foam
Weave Woven cushioned surface. For even more stability and added holster support,
accuMoLd ELiTE a high-density internal polymer stiffener runs the full length and width
of belt. You’ll notice immediately that the ErgoTek belt is both light in
weight and far more comfortable than a traditional duty belt. Plus,
these belts are lined with hook to work in conjunction with the Bianchi
7205 Liner Belt. PATENTED
fingerLok retention
™
Duraskin™ Duraskin™ Duraskin™

Plain Basket Hi Gloss The FingerLok™ device provides Auto Retention™ when the weapon is
LEaTHEr holstered, and is released by sweeping the device with the middle finger
when drawing. PATENTED
dual Belt Loop Technology

Bianchi offers its most popular duty accessories with a uniquely
Plain Tan Plain Black designed belt loop that allows for snug carry on either a
2" (50mm) duty belt or 2.25" (58mm) duty belt. This feature is
Many people still love traditional leather gear. It wears beautifully, and nothing
available on both our top end AccuMold® & AccuMold® Elite™
quite feels the same. Bianchi leather is full-grain cowhide – the best available.
accessory lines, and on our PatrolTek™ accessory line.
We choose different weights based on the product requirements, handcrafting
and molding it to perfection the old-fashioned way, by not cutting corners.
NEW PRODUCTS
rEsTraiNTs
(sHowN oN PagE 66)
Safariland offers four new handcuff models for its 2010 lineup.
The new Steloy models are 40% lighter and 70% larger than
standard cuffs. Also added to the line are the Model 8132 Rigid
Cuff and the 8142 Ultimate Hinge Cuff.
gEar Bags
(sHowN oN PagE 54)
Each of our new gear bags serves a different task and does it with
premium materials, useful features, and the quality of Safariland. The
Dual Rifle Cases will secure and protect any long gun from 36" to 46",
encompassing weapons ranging from the M4 to the Remington 700.
The Dual Handgun Case provides several convenient spare magazine
pouches in a compact package, while the Shooters' Range Bag offers
space for everything a shooter needs, including an interior removable
padded case for use on the bench.
TacTicaL gEar
(sHowN oN PagE 51)
Safariland’s newest tactical accessory, the DFA (Drop Flex Adapter), is
constructed of a flexible, yet incredibly strong synthetic polymer that provides
an alternative to the standard leg strap on Safariland thigh rigs and is especially
suited for our single strap rig (6004-10). It has the strength of the UBL, will not
pinch the hip bone, and is incredibly light. Accepts accessories for carry adjacent
to holster and places holster low enough for use with hard plate body armor.
QuicK aTTacHMENT sYsTEM – ELs

(sHowN oN PagE 60)
The latest addition to the Quick Attachment System family is the ELS, or Equipment Locking System.
Similar to the MLS and QLS, the ELS was designed specifically for tactical accessories. Its small
receiver footprint makes it very convenient to add to the accessory mounting points on tactical rigs
or in conjunction with Safariland’s 744BL belt clip, which attaches directly to the belt. Also see our
new ELS belts featuring mounting holes pre-cut into them, making placement of these mounting
accessories even easier.
Edw duTY HoLsTErs

(sHowN oN PagE 16)
A major shift has materialized within the law enforcement community regarding the tools used for
less lethal encounters. The EDW, or Electronic Discharge Weapon, has made a definite impact on
the daily lives of officers nationwide. Safariland has recognized this trend and makes an array of
different products and accessories to help officers retain and increase the effectiveness of these
weapons. The SLS, ALS, and other safety features have moved the EDW holster from a simple
device to hold the weapon, into a Retention-Level quality holster. Available in several variations to
meet the task at hand.

LEVEL I
RETENTION 6320 aLs
™
Level i
®
with Mid-ride uBL
• Level I Retention™ holster

• ALS® (Automatic Locking System)
secures weapon once holstered;
simple straight up draw once the
release is deactivated
• Hood Guard installed
PaTENT PENdiNg
• Open-top design without SLS for
quick retrieval of weapon
• SafariLaminate™ thermal-molded
construction protects handgun and
sights
• Belt loops offered: 2" (50mm) or
2.25" (58mm)
• Available in STX Tactical®, STX
Basket Weave, STX Hi Gloss and
STX Plain finishes
rETENTioN LEVELs
DUTY HOLSTERS
To us, nothing is more important than officer

safety. That’s why Safariland created the
Retention Level system as a guide to holster
selection. The holsters in this catalog are
classified by their Retention Levels to help
you choose the right holster for your needs.
6325 with drop uBL
1.5" (38mm) Belt Drop version
In the interest of safety for police officers,
Safariland introduced the Retention Level
system in 1985, providing useful holster
selection information to the marketplace.
This system helped officers evaluate and
make informed decisions on the type of
holster needed for different scenarios and
environments. Safariland set this initial
standard, and to this day is the only holster
manufacturer with established, strict testing
criteria to evaluate the Retention Level of a 6342
duty holster. aLs® Edw Holster with clip

• (ALS®) Automatic Locking System
securely locks the electronic
discharge weapon into place
without any straps or snaps to
manipulate
• Standard ride with clip-on style
belt loop that fits 1.5" (38mm), 1.75"
(45mm), 2" (50mm) and 2.25" (58mm)
belt widths
• Closed bottom with drain hole to
protect the cartridge
• Made to fit the Taser® Model X26;
safety on X26 is automatically
activated once weapon is
reholstered
• Ergonomically designed ALS®
release that is completely operable
with the thumb; depress lever,
PaTENT PENdiNg slightly rock back to draw
• Thermal-molded SafariLaminate™
construction protects handgun
and sights
• Available in STX Tactical®,
STX Plain, STX Basket
Weave and STX Hi Gloss
6312 ambidextrous Version

2
Hi-ride Level i retention

• Molded, slotted belt loop design
• Hi-ride position, slightly forward grip
cant permits fast, easy draws
• Excellent weapon retention; thumb
break with one-way directional snap
• For pistols only
• Offered in 2.25" (58mm) belt slots
• Available in Plain Black, Basket
Weave, Nylon Look and Hi Gloss
finishes
200 Top gun Level i

with Mid-ride uBL

• Features a top draw, mid-ride, straight
drop cant and a thumb break with a one-
way directional snap
• Adjustable holster tensioning device
easily allows the controlling of friction
with the turn of a screw
• For pistols or revolvers
• Offered in 2" (50mm) or 2.25" (58mm) belt
slots only
• Available in Plain Black, Basket Weave,
Hi Gloss and Nylon Look finishes
2005 with drop uBL


LEVEL II
RETENTION
™
295 Level ii
Mid-ride with uBL
DUTY HOLSTERS
• Level II Retention™ holster

• Features front wraparound thumb
break and an internal trigger guard
lock for secure weapon retention
• Mid-ride belt position and slightly
forward grip cant allow for
comfortable carry and quick,
easy draw
• Available for double-action only
pistols; not recommended for
single-action or conventional
double-action pistols
• Not available for revolvers
• Offered in 2" (50mm) or 2.25" (58mm)
belt slots only
Weave, Hi Gloss and Nylon Look
finishes
2955 with drop uBL

PaTENTEd
6280 Level ii Mid-ride with uBL

• Level II Retention™ holster • Level III Retention™ with optional
Sentry installed or tension screw
• SLS (Self Locking System) properly adjusted
• Mid-ride position allows for • Offered for weapons with and
excellent weapon protection and without rail mounted lights
quick, easy draw
• Offered in 2" (50mm) or 2.25"
• Top draw and straight drop cant (58mm) belt slots only
• For pistols or revolvers • Available in Plain Black, Basket
Weave, Hi Gloss, Nylon Look and
STX Tactical® finishes
PaTENTEd
6285 Level ii with drop uBL

• Level II Retention™ holster • Offered for weapons with and
without rail mounted lights
• 1.5" (38mm) Belt Drop version
• SLS (Self Locking System) belt slots only
• Top draw and straight drop cant • Available in Plain Black, Basket
• For pistols or revolvers Weave, Hi Gloss, Nylon Look and
STX Tactical® finishes
• Level III Retention™ with optional
Sentry installed or tension screw
properly adjusted

LEVEL III
RETENTION
™
6270 raPTor ™
Level iii
with Mid-ride uBL
DUTY HOLSTERS
• Level III Retention™ holster

• Level IV Retention™ with optional
Sentry installed
• Mid-ride position allows for
PaTENTEd excellent weapon protection and
quick, easy draw
• SLS (Self Locking System)
• Molded ejection port insert – push
down on handgun to lock, rock
slightly back to draw
belt slots only
Weave, Hi Gloss and STX Tactical®
finishes
6275 with drop uBL

070 ssiii
Level iii with Mid-ride uBL

• Mid-ride belt position and slightly
forward grip cant allow for
comfortable carry and quick,
easy draw
• Top thumb break and middle finger
release tab, internal ejection port lock
• For pistols or revolvers
• Offered for 2.25" (58mm) belt slot only
Weave, Hi Gloss and Nylon Look
finishes
0705 with drop uBL

6360
aLs® Level iii with Mid-ride uBL

• Level IV Retention™ with optional
Sentry installed
PaTENTEd & secures weapon once holstered
PaTENT PENdiNg
• Hood Guard is standard; optional
Sentry available
• Slim, compact design allows
weapon to ride close to body
• Simple straight up draw once all
releases are deactivated
• Mid-ride belt loop allows excellent
weapon protection and quick, easy
draw
• Fits available for light mounted
weapons
• Offered in 2" (50mm) or 2.25"
(58mm) belt slots only
Weave, Hi Gloss and STX Tactical®
finishes
6365 with drop uBL


LEVEL IV
RETENTION
™
6070 raPTor ™
Level iV
DUTY HOLSTERS
with Mid-ride uBL
• Level IV Retention™ holster

• Level V Retention™ holster with
PaTENTEd optional Sentry installed
• Level II Retention™ upon
reholstering
belt slots only
• Available in Plain Black,
Basket Weave, Hi Gloss
and STX Tactical® finishes
6075 with drop uBL

LEVEL V
RETENTION
™
6070 raPTor ™
Level V
with Mid-ride uBL with sentry
• Level V Retention™ holster with

optional Sentry installed
PaTENTEd
• Level II Retention™ upon
reholstering
belt slots only
• Available in Plain Black,
Basket Weave, Hi Gloss
6075 with drop uBL

UNIVERSAL BELT LOOP (UBL)
• Will not pinch or add pressure to hip bone (support
ridge removed from the belt shank) 6281Hda
drops Holster By 2"
• Locks onto the duty belt with belt slot design, no belt
tension screws needed, will not damage top of belt
• Converts holster to the 3-hole pattern; can convert
holster to other style belt loops (e.g., drop version for
duty, concealment, paddle, belt slide, or tactical)
UBL STYLES
Our popular UBL (Universal Belt Loop) is offered in three ride heights for
various body styles
Low-ride: drop version 1.5" below Mid-ride: standard ride height Mid-ride with HDA: drop version 2"
waist below waist
SPACER KITS
Spacer kits are available that position the holster away from the body to
accommodate various body shapes . Contact our Customer Care staff for
more information.
0702-PacK spacer Kit T-sPacEr-KiT

• For use with concealment holsters • For use with the 3-hole
patterned holsters
• Positions holster farther away from body for a smooth and comfortable draw
• Positions holster farther away
• Designed to customize holster location to accommodate various shapes from body for a smooth and
comfortable draw
• Designed to customize holster
location to accommodate
various shapes
Hda-KiT
• Designed to lower holster by
cusToMiZEd-KiT (Not shown) 2" (50mm)
• Positions holster away
from body to accommodate
• For use with holsters and accessories various shapes
• Positions holster farther away from body for a smooth and comfortable draw • Right and left hand specific
• Designed to customize holster/accessory location to accommodate various
shapes

DUTY HOLSTERS
7105
cruiser™ duty Holster
• A hi-ride duty holster that positions

pistol close to the body
• Top-draw design
• Made with 50% greater density foam
than standard civilian AccuMold
holsters, for firmness and strength
• Unique Coptex™ inner lining helps
protect gun finish and provides a
smooth draw
• Quick-Slide™ injection-molded belt
loop fits up to 2.25" (58mm) belts
• Available in Black Ballistic Weave
finish
PaTENTEd
7120
defender® duty Holster
• Top-draw holster with standard ride

and traditional metal reinforced
thumb snap closure
• Bianchi’s Pinch® Retention Device
(PRD™) enhances firearm retention
by gripping the pistol’s trigger guard
• Unique Coptex™ inner lining helps
protect gun finish and provides a
smooth draw
• Metal reinforced 2.25" (58mm) jacket
slot belt loop, curved for comfort
• Available in Black Ballistic Weave
finish
PaTENTEd
PaTENTEd
PaTENTEd
7920 defender ®
ii duty Holster 7115 Vanguard ™
duty Holster
• A hi-ride duty holster that positions • Unique Coptex™ inner lining helps • A hi-ride duty holster that positions pistol • Quick-Slide™ injection-molded belt loop
pistol close to the body protect gun finish and provides a close to the body fits up to 2.25" (58mm) belts
smooth draw
• Top-draw design • Top-draw design • Available in Black Ballistic Weave finish
• Quick-Slide™ injection-molded belt
• Made with 50% greater density foam loop fits up to 2.25" (58mm) belts • Made with 50% greater density foam
than standard civilian AccuMold than standard civilian AccuMold
holsters, for firmness and strength • Available in Black Plain, Basket holsters, for firmness and strength
Weave and Hi Gloss finishes
• Unique Coptex™ inner lining helps protect
gun finish and provides a smooth draw

6340 NEw aLs Edw
®
Holster with Mid-ride
• Level I Retention™ Holster

• Automatic Locking System (ALS®)
manipulate
• Mid-ride UBL allows excellent
retention
Safariland offers a wide array • Made to fit the Taser® Model X26;
HOLSTERS
ELECTRONIC DISCHARGE WEAPONS
of holster models to address the activated once weapon is
market expansion in the use of reholstered
EDWs, or electronic discharge • Ergonomically designed ALS®
weapons. Safariland’s SLS, ALS release that is completely operable
and other safety features have with the thumb; depress lever,
slightly rock back to draw
improved the offerings of the EDW
holster from a simple device to • Thermal-molded SafariLaminate™
construction protects handgun and
hold a weapon into a Retention sights
Level-quality holster.
belt slots only
Plain, STX Basket Weave and
STX Hi Gloss
6342 NEw aLs

EDW
®
Edw Holster
with clip

manipulate
• Hi-ride with clip-on style belt loop
that fits 1.5" (38mm)-2.25" (58mm)
belt widths
reholstered
construction protects EDW
and sights
STX Plain, STX Basket Weave
and STX Hi Gloss
745BL
• Features 745BL Belt Clip
for easy attachment and
detachment from belt.
See page 27 for details 6312 ambidextrous Version
6345 NEw aLs ®
Edw Holster
with Low-ride

manipulate
• 1.5" (38mm) belt drop version; UBL
provides added comfort for wear
on duty belt - will not pinch or add
pressure to hip bone
reholstered
construction protects EDW and
sights
• Offered in 2" (50mm) or
2.25" (58mm) belt slots only
6315 ambidextrous Version STX Hi Gloss
6347 NEw aLs ®

Edw Holster
with Belt slide

manipulate
• Mid-ride with the 567BL belt loop
for a close to body fit
reholstered
sights
• Accommodates belts from 1.5"
(38mm) to 2.25" (58mm) in width;
also available in additional belt loop
options
6317 ambidextrous Version STX Hi Gloss

HOLSTERS
6374 aLs ®
Edw Holster
with 6004 Leg shroud

manipulate
EDW

reholstered
sights
• Standard double leg strap and leg
shroud with mounting holes for
optional accessories
STX Plain, STX Basket Weave, STX
Hi Gloss and FDE Brown finishes
6375 aLs® Edw Holster with

6005 Leg shroud

manipulate
activated once weapon Is reholstered
sights
• Adjustable vertical leg strap with
quick-release detachable leg strap
Plain, STX Basket Weave, STX Hi
Gloss and FDE Brown finishes
6348 aLs® Edw Holster
with Paddle

manipulate
• Standard ride with injection-molded
contoured paddle for comfort
reholstered
sights
Plain, STX Basket Weave and STX
Hi Gloss finishes
6318 ambidextrous body design

can be used with purchase
of left hand paddle
BacK BacK
520 Thumb Break clip-on style 519 Thumb Break Belt slide
• SafariLaminate™ construction with suede lining • SafariLaminate™ construction with suede lining
• Clip-on style belt loop with the ability to fit 1.5" (38mm), 1.75" (45mm), • Adjustable injection-molded belt loop is user-adjustable for cant angle; designed for
2" (50mm) or 2.25" (58mm) belts vertical or cross draw carry and fits 2.25" belt
• Belt loop is user-adjustable for cant angle; designed for vertical or • Optional belt loop for 1.5" (38mm), 1.75" (45mm), 2" (50mm) or 2.25" (58mm) belts
cross draw carry • Closed bottom with drain hole to protect cartridge
• Closed bottom with drain hole to protect cartridge • Available in Plain Black, Basket Weave and Hi Gloss finishes
• Available in Plain Black, Basket Weave and Hi Gloss finishes

HOLSTERS
6280 Level ii
Mid-ride with uBL
• Level II Retention™ Holster
• All the features of the Model 6280
on page 9
• Now available to carry advanced
Taser® M26 or X26
EDW
belt slots only

• Available in STX Plain, Nylon-Look
PaTENTEd and STX Tactical® finishes
6520 sLs Edw Holster

with clip
• Level II Retention™ Holster

• SLS (Self Locking System) feature
• Clip-on style belt loop with ability
to fit 1.5" (38mm), 1.75" (45mm), 2"
(50mm) or 2.25" (58mm); belt loop is
user-adjustable for cant angle
• Designed for vertical or cross draw
carry
• Closed bottom with drain hole
• SafariLaminate™ construction with
suede lining
• Available in STX Plain, Nylon-Look
PaTENTEd
PaTENTEd
521-caP Edw cartridge accessory Plate 6287 sLs Edw Belt slide
• Attaches to the 745BL Belt Clip • Level II Retention Holster™
• Provides convenient storage area for additional • Rides close to body
EDW cartridge
• Universal Belt Loop available in 7 options
• Available for Models 520 & 6520
• Adjustable cant, can be worn strongside or cross draw
• Available in Plain Black, Basket Weave, Hi Gloss and Nylon-Look finishes
• Closed holster bottom to protect cartridge and officer
Holster sold separately
• SafariLaminate™ construction with suede lining
• Available in Plain Black and STX Tactical® finishes
6281uBs-caP Edw accessory Belt Mounting system

• SafariLaminate™ construction with suede lining
• Snap-on belt attachment for Taser® holsters
• Adjustable cant for optional cross draw wear
• Offered with 2" (50mm) or 2.25" (58mm) belt slots only
• Available in Plain Black, Hi Gloss, Basket Weave and Nylon-Look finishes
Holster sold separately

031 d-ring Belt 1.5" (38mm) 87/87V suede Lined with Buckle
• Reinforced instructor-style belt 2.25" (58mm)
• Lined with loop material • Standard duty belt with a suede lining
• 4-stitch design
• Double-tongued buckle and center belt stud fasten
belt firmly around waist
• Free-sliding keeper holds the belt tip in place
• 87V with hook & loop
• Choice of chrome or brass buckle
All belts available in Black

DUTY BELTS
unless otherwise specified.
51 garrison with square Buckle 1.75" (45mm) 94/94P Buckleless ™

Belt 2.25" (58mm)
• Full grain leather construction • Features a hidden brass hook and a hook & loop
closure on both ends
• Includes removable square chrome or brass buckle
• Belt is lined with a band of hook & loop and attaches
to the lining on the Model 99 or 992, completing the
Buckleless system
• 94P without hook & loop
99/999 Buckleless ™
reversible Belt 1.5" (38mm) 146/146V Border Patrol with Buckle
• Hook & loop can be worn on the outside, creating a
2.25" (58mm)
Buckleless system • Standard buckle fastens the belt firmly around
the waist
• Order 999 for belt without loop lining
• The 1.25" (32mm) and 2.25" (58mm) keepers hold the
interior and exterior belt tips in place
992 reversible safariLaminate ™

Belt 1.5" (38mm) 872/872V contoured Belt 2.25" (58mm)
• Lined with loop material • 4-stitch design with suede lining and free-sliding keeper
to hold belt tip in place
• Designed to be worn under duty belts with hook as the
foundation of the Safariland™ belt systems • 2.25" (58mm) duty belt is contoured for proper
alignment and greater comfort
• The 992 is the contour version of the 99
• Greater all-day comfort by distributing weight evenly;
no sharp edges to dig into hips
942/942P contoured Buckleless ™

Belt 2" (50mm)
or 2.25" (58mm)
• Tip of belt points to the right side of the officer 875 stitched Edge with Buckle Belt
2.25" (58mm)
• Greater all-day comfort by distributing weight evenly; no
sharp edges to dig into hips • Standard duty belt with a plain border stitch
• Lined with hook & loop to mate with 99 underbelt • Double-tongued buckle and center belt stud fasten belt
firmly around waist
• 942P without hook & loop
• Features a hidden brass hook closure
4325 Nylok ®
Pro Buckleless™ 94243 Leather/Laminate Belt with 3X ™
Locking 4307 Ballistic Nylon Laminated duty Belt with 3X ™
reversible Belt 1.5" (38mm) Buckle, contour fit 2" (50mm) Locking Buckle 2.25" (58mm)
• Hook & loop closure • Laminate duty belt with a leather outer finish • Features full-length hook lining
• Lined with loop material • Contoured for proper alignment and greater comfort for • Includes two Flex-Cuf® channels (see page 71)
both men and women
• Features the 3X™ Locking Buckle System
9443/9443V Leather/Laminate Belt 4306 Ballistic Nylon duty Belt with 3X ™

Locking 4356 Ballistic Nylon duty Belt with 3X ™
Locking
Buckle 2"
with 3X™ Buckle 2" (50mm) Buckle 2" (50mm)
(50mm) or 2.25" (58mm) • A third center lock for added security • Both ends are skived,
• Laminate duty belt with a leather outer finish allowing a lower
• Features full-length hook lining profile around the
• 9443V features hook lining buckle
• Both ends are skived, allowing a lower profile around
• 3X™ Locking Buckle System the buckle • Available in FDE
Brown, Foliage
Green or Black
finishes
4332 NEw ELs duty Belt 2" (51mm)

• Features full length hook lining for use with 8106
Liner Belt
• Buckleless design features two large knobs for
locking in ELS mounting holes
• Pre-cut ELS mounting holes for straight up or angled
attachment of ELS Receiver Plates
ELs sold separately (see page 60)
4320 Padded Belt Liner

• Provides a padded buffer between duty belt and body
• Helps eliminate possible bruising and other comfort
issues associated with wearing a duty belt for long
periods of time

DUTY BELTS
7201 Nylon Training Belt 1.75" (45mm) 8106 Liner Belt – Loop 1.5" (38mm)
• Four-part laminate for long-lasting shape and exceptional • Loop surface for use with 7203 Duty Belt
durability
• Tough web construction
• Hook & loop closure for quick on/off ease
• Firm polyethylene center strip sandwiched between
a high-density foam, then ballistic weave outer and a
durable nylon lining
7202 Nylon Training Belt 1.75" (45mm) 7950 duty Belt 2.25" (58mm)
• High-density four-part laminate for long-lasting shape • Four-part laminate for long-lasting shape and
and exceptional durability exceptional durability
• Firm polyethylene center strip sandwiched between • Duraskin™ exterior with loop lining for use with
a high-density foam, with ballistic weave outer and a Bianchi® 7205 Liner Belt
durable nylon lining for 7202, 7950, 7980, 7210, 7955
• Closed-cell foam for support and comfort
• Shatter-resistant polymer buckle
• Tri-Release™ shatter-resistant, polymer buckle features
3-point release for added security
7205 Liner Belt 1.5" (38mm) 7960 sam Browne Belt 2.25" (58mm)
• Hook & loop closure for quick on/off ease • Four-part laminate for long-lasting shape and
exceptional durability
• Lined with hook
• Closed-cell foam for support and comfort
• Duraskin™ exterior with loop lining for use with
Bianchi® 7205 Liner Belt
PaTENTEd
8105 Liner Belt – Hook 1.5" (38mm) 7965 ErgoTek ™

sam Browne Belt 2.25" (58mm)
• Hook surface for use with 8100 Duty Belt • Accepts standard holster and pouches
• Tough web construction • Load support cushions on belt lining spread
weight of gear over entire waist
• Provides a padded buffer between stiff outer
belt and accessories and the wearer
• Duraskin™ exterior with loop lining for use with
Bianchi® 7205 Liner Belt
7970 Buckleless ™
duty Belt 7215 Border Patrol Belt 2.25" (58mm) 8100 duty Belt 2" (50mm)
2.25" (58mm) • Ballistic weave fabric with loop lining encases a • Tri-Release™ shatter-resistant polymer buckle with
• Four-part laminate construction foam-layered stiffener for support and comfort 3-point release
• Closed-cell foam for support and comfort • Metal parachute-style buckle closure • Loop lined for use with 8105 Liner Belt
• Positive 3-way retention using hook & loop, • Accepts standard Safariland™ UBL • Tough, double-layered web construction
retaining stud and belt keeper • Belt 2.25" (58mm) • Smooth, edge-bound finish for extra comfort
• Adjustable in ½" increments
• Duraskin™ exterior with loop liner for use
with Bianchi® 7205 Liner Belt
PaTENTEd PaTENTEd
7980 ErgoTek ™
duty Belt 2" (50mm) 7225 ErgoTek ™
duty Belt 2.25" (58mm) 8110 duty Belt with Hook Lining 2" (50mm)
• Four-part laminate construction for extra • Five-part laminate for extra durability • Tri-Release™ shatter-resistant polymer buckle with
durability 3-point release
• Load support cushions on inner lining distribute weight of
• Duraskin™ exterior with loop lining for use duty belt over entire waist for comfort during the entire shift • Hook lined for use with 8106 Liner Belt
with Bianchi® 7205 Liner Belt
• Ballistic weave fabric with loop lining for use with Bianchi® • Five-part laminate for extra durability
• Tri-Release™ shatter-resistant, polymer 7205 Liner Belt
buckle features 3-point release for added • Tough, double-layered web construction
security • Accepts standard holsters and pouches
• Smooth, edge-bound finish for extra comfort
• Coplok™ shatter-resistant, polymer buckle features 3-point
release for added security
7200 duty Belt 2.25" (58mm) 7990 Buckleless ™

adjustable Belt 2" (50mm) 8300 Nylon Belt system 2" (50mm)
• Five-part laminate construction for long- • Multi-laminate construction for durability • Tri-Release™ shatter-resistant polymer buckle with
lasting shape and extra durability 3-point release
• Buckleless system allows for adjustments in ½"
• Ballistic weave fabric outer and loop lining, increments • Hook & loop lining
with foam center, and a stiffener sandwiched
between two layers of closed-cell foam for • Duraskin™ exterior with loop lining • Five-part laminate for extra durability
support and comfort • Includes duty belt, liner and 4 attached keepers
• Coplok™ shatter-resistant, polymer buckle
features 3-point release for added security
PaTENTEd
7210 duty Belt 2" (50mm) 7955 ErgoTek ™

duty Belt 2.25" (58mm)
• Five-part laminate for extra durability • Four-part laminate for long-lasting shape and
• Ballistic weave fabric outer and loop lining,
with foam center, and a stiffener sandwiched • Duraskin™ exterior with loop lining for use with
between two layers of closed-cell foam for Bianchi® 7205 Liner Belt
support and comfort
• Load support cushions on inner lining spread load of
• Tri-Release™ shatter-resistant, polymer duty belt over entire waist
buckle features 3-point release for added
security • Tri-Release™ shatter-resistant, polymer buckle
features 3-point release for added security

SLS ACCESSORIES
Three uniquely designed SLS (Self Locking System) accessories for Safariland duty holsters with
the SLS, Raptor and ALS (Automatic Locking System) systems. Available for the following models:
• SLS: 6004, 6005, 6280, 6285, 6287, 6295, 62955
• RAPTOR™: 6070, 6075, 6270, 6275
• ALS®: 6304, 6305, 6354, 6355, 6360, 6365
BacK ViEw
froNT ViEw
DUTY ACCESSORIES
6000 sLs Hood guard

• Features a uniquely designed accessory protection for the
SLS holster system
• Will adapt to any SLS holster
• Colors: Black, FDE Brown, Foliage Green
6001 sLs sentry

• Features a uniquely designed accessory protection for the
SLS holster system
• Will adapt to any SLS holster and increase the retention
level by one
• Color: Black
6002 sLs sentry & Hood guard

• Features the Sentry installed into
the Hood Guard
• Will adapt to any SLS holster
• Colors: Black, FDE Brown, Foliage Green
• Note: Sentry only available in black
HOLSTER MOUNTING
PLATFORMS UNIVERSAL BELT LOOP (UBL)
• Will not pinch or add pressure to hip bone (support
Safariland offers the broadest line of holsters for law enforcement, so it ridge removed from the belt shank)
follows that we would also provide the most extensive line of mounting
• Locks onto the duty belt with belt slot design, no belt
platforms and accessories for our holsters. These options add versatility, tension screws needed will not damage top of belt
comfort and convenience as you perform your duties. From our
• Converts holster to the 3-hole pattern; can convert
Universal Belt Loop (UBL) to our belt slides, our new Drop Flex Adapter holster to other style belt loops (e.g., drop version for
and more, there is a mounting platform to fit your needs. duty, concealment, paddle, belt slide, or tactical)
6070 uBL 6075 uBL

2" or 2.25" 2" or 2.25"
567BL 1.5" To 1.75"
567BL 1.75"
6004-dfa NEw drop flex adapter
• Allows user to wear a thigh rig below the hip without
shifting weight farther down the leg
• Keeps rig from sliding on belt
6070uBL-Pad
• Can be used on belt widths up to 2.25" (58mm) 6075uBL-Pad
• For use in conjunction with the current 6004-10 • Provides a soft pad between the body and Universal
leg shroud Belt Loop (UBL)
• Helps address comfort issues associated with
wearing a duty belt for long periods of time
• Works equally well for both male and female officers
567BL 2.25"
745BL Belt clip

• Designed with a 3-hole pattern, allowing
interchangeability among various Safariland holsters
• Clips on/off belt without having to remove other
accessories on rig
568BL up To 1.75" • Made of durable nylon; will pass a Level I Retention™
pull test P2201 converts 2.25" uBL To a 2" Belt slot
• Fits belt widths from 1.5" (38mm) to 2.25" (58mm)
Seven different 567BL belt loop options available for
1.5" to 2.25" belt widths and hi-ride/mid-ride carry.

DUTY ACCESSORIES
75* open Top double Magazine Pouch 72 double Magazine and cuff Pouch
• Open-top design • Adjustable angle positions designed into belt loop
• Low cut and span between pouches for quick retrieval • Designed to carry two handgun magazines and one
pair of handcuffs
• Tension screw allows retention adjustment
• Adjustable tension device to help retain magazines
in pouch
77* double Magazine Pouch 176 Extreme duty Magazine Pouch

SafariLaminate ™ • Vertical/horizontal belt slots for regular/low-profile • Pivots away from body to prevent interference with
position body armor
• Tension screw allows you to adjust magazine retention • Spring loaded to lift magazine above other duty gear on belt
• Span between pouches plus low cut allow quick, • Magazine is secure in pouch in inverted position with
• Our original and most extensive holster and easy drawing securing strap removed
accessory line
• Part of the 6004/6005 tactical system • Securing strap releases with one finger
• Durable lamination process
• Part of the 6004/6005 tactical system
• Known as the performance gear that law
enforcement professionals recognize as the
uniquely famous Safariland line
• All accessories are designed to fit 2.25" (58mm)
duty belts unless otherwise specified
• Finishes offered: SafariLaminate™ Plain, Basket
Weave and Hi Gloss
• Many Safariland duty accessories are
available with hidden snap closure.
Visit safariland.com/dutygear
• Snap versions available in Chrome, Brass or Black
73 open Top double Magazine Pouch 277* Quad Magazine Pouch
• Features adjustable angle positions for both vertical and • Designed with space for up to four 1911-style
horizontal carry magazines; also offered in 10-round versions
• Low cut design and space between pouches for quick • Center divider retains extra magazine while fixed
magazine retrieval magazine is in use
• Tension screw allows retention adjustment • Vertical or horizontal belt slots for standard or low
profile positions
• Ideal for agencies that require a certain amount of
ammunition yet allow 1911-style weapons
76* single Magazine Pouch HK-11 Hide-a Keyper ™
• Several sizes to fit most popular magazines • Hidden handcuff key on

inside of belt keeper
Items noted with (*) are also
available in STX Tactical® finish
62 Belt Keeper 692s Baton ring with snap 730 Heavy duty flashlight ring
• Slot fits up to 1.75" (45mm) belts • For side-handle batons • Heavy-duty
• Hidden snap • Snaps/slides on duty belt • Features a shatter-resistant nylon ring
• 1-snap closure
• For D-cell and C-cell flashlights
654 slotted Belt Keeper 67/67s Baton ring 170 silent Key Holder
• Slot fits up to 1.75" (45mm) belts • Also fits C-cell flashlights • SafariLaminate™ key ring
• 4-snap closure • 67 (not shown) is without snap • Hook & loop adjustable pouch
63 slotted Belt Keeper 168 Key ring 306* open Top Mini-flashlight Holder
• Slotted, two-snap belt keeper • Heavy-duty metal spring hook • Half-sheath style fully protects selected mini
• Slot fits up to 1.75" (45mm) belts • Protective flap flashlights
• Does not include key
• 2-snap design
65 Belt Keeper
• Standard 0.75" (19mm) belt keeper
• Design matches all 2.25" (58mm) duty belts
• Also available for 2" (50mm) belts 169s Key ring 308* Hand-Held flashlight Holder
• Heavy-duty metal spring hook • Flap closure style to fit select hand-held lights
655 Heavy duty Belt Keeper • Allows for easy key removal • Part of the 6004/6005 tactical system
• Rugged, heavy-duty, two-snap belt keeper • 1-snap design
• Extra wide at 1.25" (32mm)

DUTY ACCESSORIES
690 Handcuff strap 38* oc/Mace ®

Holder
• Secures one pair of cuffs to your duty rig • Top flap for added security
• Saves space on duty belt • Part of the 6004/6005 tactical system
• 1-snap design
SafariLaminate ™
90/90H Handcuff case 381* oc/Mace ®

Holder
• Specify chain or hinged cuffs • Fits both MK-9 Magnum and Training Unit
• 90H (not shown) fits hinged cuffs • Metal clip for easy removal on and off belt
090 open Top Handcuff case 190*/190H* Handcuff case 765 oc Holder with clip
• Open-top formed • Specify chain or hinged cuffs • Fits both MK-9 Magnum and Training Unit
• Fits chain or hinged cuffs • 190H (not shown) fits hinged cuffs
290/290H double Handcuff case 37* open Top oc/Mace ®

Holder 33 surgical glove Holder
• Specify chain or hinged cuffs
• Open-top for quick access • Hook & loop closure
• 290H (not shown) fits hinged cuffs
• Part of the 6004/6005 tactical system • Holds one or three pair of surgical gloves;
please specify
35* Baton Holder 38-8* impact round case, Top flap 762* radio Holder with swivel
• Designed for expandable baton • Closed top pouch for 37/40mm less lethal rounds • Features a detachable swivel belt loop for easy retrieval
• Extended baton can be reholstered • Designed for the eXact Impact™ and Direct Impact® rounds • Protective pouch and adjustable bungee cord
tie-down with a snap closure
• Fits 16" (406cm), 21" (533cm) or 26" (660cm) • Can be ordered for 2.25" (58mm) belt slide or mount on leg
length batons and vest accessory
• Part of the 6004/6005 tactical system • Part of the 6004/6005 tactical system
135* Baton Holder 767 cassette recorder Pouch 763 universal radio Holder – Portable
• Designed for expandable baton • For the Olympus Voice & Music DM-1 recorder • Universal fit
• Fits 16" (406cm), 21" (533cm) or 26" (660cm) • Features an adjustable band to fit almost any standard
length batons portable police radio
• 26" length also fits Streamlight Stinger® • Bottom lip prevents the radio from falling through
• Available in two sizes for 1.5" and 2"-2.25"
(38mm-58mm) belts
307* Light/Edw cartridge Holders 764 cassette recorder case 768 Pager Holder
• Fits 2" to 2.25" (50mm-58mm) duty belt • Fits recorders up to 2.5" W x 1.5" H x 3.5" L (64 x 38 x 89mm) • Metal clip attachment to fit 2" to 2.25" (50mm-58mm)
duty belt
• Pouch to hold lights for mounting to gun • Features a protective pouch and an adjustable bungee
cord tie-down with a snap closure
• Designed for the Taser® cartridge
080-12 081-12
080-12 shotgun shell Holder

081-12 NEw shotgun shell Holder
37-8* open Top impact round Holder 761* adjustable radio Holder • Molded shotgun shell holder holds 2 12-gauge shells
• Open-top pouch for 37/40mm less lethal rounds • Formed protective pouch • Belt clip features an extended bottom hook for security
• Can be ordered for 2.25" (58mm) belt slide or • Adjustable bungee cord tie-down with a snap closure • 080-12 features belt clip with bottom hook for security;
mount on leg and vest accessory fits belts up to 2.25" (58mm)
• Fits most standard portable police radios
• Part of the 6004/6005 tactical system • 081-12 features mounting holes

DUTY ACCESSORIES
775* NEw slimline open Top Triple 371 split-six single speedloader Holder
Magazine Pouch • Single speedloader
• Provides triple magazine retention without flap in an area
comparable to standard dual magazine pouches • Featuring ultra-low profile and quick, easy, single-action
draw, providing the fastest “top-flap” speedloader available
• Durable SafariLaminate construction
™
• Design carries cartridges on either side of the belt
• Vertical and horizontal belt slots
• Allows you to grip both sides of the loader while
• Magazines are oriented “face out” to save space unsnapping the top flap
• Fits 2.25" (58mm) belt widths • Designed for 1.75" (45mm) belts
ML-1, ML-2 Magazine Loaders

777* NEw slimline Triple Magazine Pouch • Pocket-sized loaders allow fast and easy
SafariLaminate ™
• Magazines are oriented “face out” to save space on duty belt
• Vertical and horizontal belt slots
reloading of magazine clips
• ML-1 fits all double-row 9mm and single-row .45
magazines, except for Glock and H&K
• Durable SafariLaminate construction
™
• ML-2 submachine gun magazine loader fits
• Fits 2.25" (58mm) belt widths Beretta, Colt, H&K, Uzi 9mm Carbine, and
submachine gun magazines
78* NEw slimline double Magazine Pouch

• Magazines are oriented “face out” to save space on belt
• Optimal for use on tactical rigs due to minimal width
• Durable SafariLaminate™ construction cd-6 speedloader Holder
• Vertical and horizontal belt slots 340 double speedloader Holder • Strong, epoxy-coated steel clips
• Lined with a vinyl pad insert to ensure loader stability
• Fits 2.25" (58mm) belt widths • Standard double speedloader
• Part of the 6004/6005 tactical system • Split-Six CD-6 is designed for 1.75" (45mm) belts
• Fits 2.25" (58mm) duty belts
• Available in epoxy finish
• Chrome or brass snap
• Metal clip-on construction
79* NEw slimline open Top double Magazine

Pouch
• Magazines are oriented “face out” to save space on
duty belt 370 split-six double speedloader Holder cd-2 speedloader Holder
• Optimal use on tactical rigs due to minimal width • Double speedloader holder • Strong, epoxy-coated steel clips
• Durable SafariLaminate™ construction • Featuring ultra-low profile and quick, easy, single-action • Lined with a vinyl pad insert to ensure loader
draw, providing the fastest “top-flap” speedloader stability
• Vertical and horizontal belt slots holder available
• CD-2 clips firmly onto any belt up to 2" (50mm)
• Fits 2.25" (58mm) belt width • Design carries cartridges on either side of the belt wide
• Part of the 6004/6005 tactical system • Allows you to grip both sides of the loader while • Available in epoxy finish
unsnapping the top flap
• Metal clip-on construction
• Designed for 2.25" (58mm) belts
NYLOK PRO
®
• Made of durable ballistic nylon, it’s lightweight and

rugged and resists scuffs, tears, and fading
• The NYLOK® PRO product line combines the best of our
original, patented NYLOK® survival gear line
• Molded accessories of SafariLaminate™ with non-glare
black matte snap closures that fit belts up to 2.25" (58mm)
• NYLOK® PRO features a 1050-denier weave
• The NYLOK® PRO line of accessories was designed to be
used with Safariland’s STX Tactical® duty holsters
4208 Baton Holder

• SafariLaminate™ molded construction
• Available for most 21" (53.34cm) or 26" (66cm)
foam-handle expandable batons
• Fits 2.25" (58mm) belt loop
4110 double Magazine Pouch 4100 single Magazine Pouch 4238 Mini flashlight Holder
• Featuring a two-way belt loop for either • Five sizes available • Flap-style mini flashlight pouch carries most mini
vertical or horizontal use flashlights
• Adjust the tension screw for extra magazine • SafariLaminate™ molded construction
retention for a more custom fit • Fits 2.25" (58mm) belt loop
4258 Handcuff case 4298 radio Pouch, swivel 4278 oc/Mace ®

Holder
• Constructed of molded SafariLaminate ™
• SafariLaminate molded construction
™
• Fits many small canisters up to 4.5" (11cm) high
• Fits chained cuffs • Available in 2" x 2.8" x 3.75" (51mm x 73mm x 95mm) • SafariLaminate™ molded construction
• Fits 2.25" (58mm) belt loop • Available in 1.6" x 2.25" x 3.5" (41mm x 58mm x 89mm) • Fits 2.25" (58mm) belt loop

DUTY ACCESSORIES
PaTENTEd
ars radio swivel attachment 7300 covered Handcuff case

• ARS belt loop swivel attachment also sold separately • 2 sizes hold one pair linked or hinged handcuffs
• 2.25" (58mm) belt loop • Hook & loop or hidden snap closure
• Dual web belt loop fits both 2" (50mm) and 2.25" (58mm) belts
• Also available in OD
AccuMold
®
PaTENTEd PaTENTEd
• AccuMold® is an exclusive Bianchi technology 7314 universal radio Holder 7317 double Handcuff case
featuring a patented method of molding to contour • Elastic security strap with snap closure • Holds two pair standard linked handcuffs
the laminate to the exact shape of the equipment
it will carry • 2 models fit most hand-held radios • Hook & loop or hidden snap closure
• Its trilaminate construction features a ballistic • Also available in OD • Dual web belt loop fits both 2" (50mm) and
weave fabric exterior with a high-density, closed- 2.25" (58mm) belts
cell foam center and a smooth Coptex™ knit lining
• AccuMold® magazine pouch cavities expand both
front and rear, making for a snugger fit, a trimmer
look and less strain on the equipment
• AccuMold® pouches feature our exclusive Roll Top™
lid for a smooth, rounded closure and a custom fit
for equipment of various sizes
• Pouches feature either a hidden snap or hook &
loop closure PaTENTEd
• Some models available in OD

• Fits 2.25" (58mm) belts unless otherwise specified 7318 ultimate Hinge Handcuff case
7323 adjustable radio Holder • Holds one pair Safariland 8142 cuffs
• Hook & loop or hidden snap closure
• Holds compact hand-held radios
• Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts
• Elasticized security strap
• Slim design offers less bulk
PaTENTEd PaTENTEd
7324 slimline radio Holder 7334 open Top Handcuff case

• Holds compact hand-held radios • Holds one pair lined handcuffs
• Elasticized security strap • Dual web belt loop fits both 2" (50mm) and 2.25" (58mm) belts
• Slim design offers less bulk
PaTENTEd PaTENTEd
PaTENTEd
7310 Mini-Light Holder 7303 single Magazine Pouch 7308 open Top oc/Mace ®
Holder
• Fits AA-cell lights • Hook & loop or hidden snap closure • 2 sizes fit MK-3 & MK-4 canisters
• Hook & loop or hidden snap closure • Dual web belt loop fits both 2" (50mm) and 2.25" (58mm) • Sturdy web belt loop
belts
• Dual web belt loop fits 2" (50mm) and 2.25" • Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts
(58mm) belts
PaTENTEd
PaTENTEd PaTENTEd
7311 compact Light Holder 7302 double Magazine Pouch 7307 oc/Mace ®
spray Holder
• Injection-molded belt loop for horizontal or vertical carry • Two sizes for MK-3 and MK-4 canisters
• 3 sizes fit most compact lights
• Hook & loop or hidden snap closure • Hook & loop or hidden snap closure
• Also available in OD • Dual web belt loop fits both 2" (50mm) &
• Dual web belt loop fits both 2" (50mm) & 2.25" (58mm) belts
2.25" (58mm) belts
PaTENTEd
PaTENTEd
7327 rail Mounted Light Holder 7320 Triple Threat ™

ii double Magazine Pouch 7333 iwB Baton Holder
• Compact and protective • Injection-molded belt loop for vertical or • Dual web belt loop fits both 2"
horizontal carry (50mm) and 2.25" (58mm) belts PaTENTEd
• Two sizes to fit Streamlight M3, M5, M6 &
®
Glock GTL10 • Tension screw adjustment permits various • Covered hole in back allows
drawing angles baton to be placed in pouch fully
• Dual web belt loop fits 2" (50mm) & 2.25" expanded
(58mm) belts
PaTENTEd
PaTENTEd
7326 compact Light Holder 7301 speedloader Pouch 7312 Expandable Baton Holder
• 2 sizes fit most compact lights; e.g., • AccuMold® trilaminate with ballistic weave exterior and • Covered hole in back allows baton to be placed in
SureFire® 6P, 6R, Streamlight® Stinger XT, Coptex™ lining pouch fully expanded
Poly Stinger, Scorpion
• Dual web belt loop design fits 2" (50mm) and 2.25" (58mm) • Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts
belts

DUTY ACCESSORIES
PaTENTEd
7313as auto-open Baton Holder 7404 Baton ring

• Adjustable swivel mount • Fits standard and side-handle batons
• Baton fully extends as it is being drawn from the holder • Sturdy, injection-molded ring
• Trilaminate construction with ballistic weave exterior and • 1" web
Coptex™ lining
• Fits Monadnock® AutoLock® HG 21" baton only
PaTENTEd
7313 Expandable Baton Holder 7405K Key Holder Belt Keeper

• 3 sizes for 16"–26" batons; e.g., Monadnock®, ASP® • 1" web keeper with polymer key holder attached
and similar
• Saves room on duty belt
• Dual snap closure
7409 flashlight ring 7405 Key Holder

• Molded ring locks flashlight in place • Holds standard key ring
• 1" web • 1" web
7409K flashlight ring Belt Keeper 7328 flat glove Holder

• Molded ring locks flashlight in place • Holds two pair latex gloves
• 1" web keeper with molded ring saves room on belt • Trim & compact
• Dual web belt loop fits both 2" (50mm) and
2.25" (58mm) belts
7340 Bandolier Pouch
• Designed to fit 2 FN303 magazines
• Pouch can be separated from bandolier and
mounted on any MOLLE platform
• Bandolier has extra locations to mount
additional MOLLE-compatible pouches
PaTENTEd
• 2" quick-release buckle for ease of use
7315 Pager/glove Holder • Adjustable elastic security strap with snap

closure
• Holds most pocket pagers or two pair
latex gloves
• Dual web belt loop fits both 2" (50mm)
and 2.25" (58mm) belts
PaTENTEd
7329 cell Phone Holder

• Fits Nextel i205 and similar
• Snap or hook & loop closure
• Dual web belt loop fits 2" (50mm) and 2.25"
(58mm) belts
PaTENTEd
7316 silent Key Holder

• Roll Top™ wraparound design
• Hook & loop closure
7406 Belt Keeper

• 1" web
• Dual-snap or hook & loop closure
• Sold in 4-pack

DUTY ACCESSORIES
7923 adjustable radio Holder 7918 ultimate Hinge Handcuff case

• 2 sizes hold compact hand-held radios • Holds one pair Safariland™ Model 8142 handcuffs
or similar
• Elasticized security strap
• Dual web belt loop fits 2" (50mm) and
• Slim design offers less bulk, more convenience 2.25" (58mm) belts
AccuMold Elite
® ™
• Lightweight – up to 50% lighter than leather in 7914s universal radio Holder 7934 open Top Handcuff case
most applications • Holds most hand-held radios • Holds one pair linked or hinged handcuffs
• More affordable than leather • Elasticized security strap with snap closure • Dual web belt loop fits 2" (50mm) and
• Improved comfort translates into better officer 2.25" (58mm) belts
• 2-piece adjustable swivel mount for comfort when riding
performance in the field in a vehicle
• Same beautiful look as leather – the crisp,
professional appearance of premium leather
without the weight, maintenance and cost
• Abrasion-resistant – exhibits a high level of
resistance to the daily knocks, scuffs and
abrasions of duty use. Less work to maintain that
“inspection day” look!
• Easily cleaned with only mild soap and water.
Bio-safe: Washing with disinfectant soap or
bleach solution will handle contamination
problems. Great for correctional institution duty
• All molded accessories feature the dual molded
belt loop to fit both 2" (50mm) and 2.25" (58mm) 7900 covered Handcuff case 7927 rail Mounted Light Holder
belt widths • Holds one pair linked or hinged handcuffs • Compact & protective
• Chrome, brass or hidden snap • 2 sizes fit Streamlight®, M3, M5, M6 & Glock GTL10
• Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts • Dual web belt loop fits 2" (50mm) and
2.25" (58mm) belts
7917 double Handcuff case 7911 covered compact Light Holder

• Holds two pair linked handcuffs • 3 sizes fit most compact lights; e.g.,
Streamlight®, SureFire®, S&W
• Chrome, brass or hidden snap
7909 d-cell Light Holder 7902 double Magazine Pouch 7922 Triple Threat ™
ii double Magazine Pouch
• Molded ring locks flashlight in place • Vertical or horizontal carry • Injection-molded belt loop for vertical or horizontal
carry
• Snap-on belt loop • 4 sizes to fit most magazines
• Tension screw adjustment permits various drawing
• Injection-molded belt loop angles
7926 compact Light Holder 7903 single Magazine/Knife Pouch 7928 flat glove Holder
• 2 sizes fit most compact lights; e.g., SureFire® • 3 sizes fit most magazines • Holds two pair latex gloves with hook & loop closure
6P, 6R; Streamlight® Stinger XT, Poly Stinger,
Scorpion • Hidden snap • Trim and compact
• Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts • 2.25" (58mm) belt loop

DUTY ACCESSORIES
7908 open Top oc/Mace ®

Holder 7912 Expandable Baton Holder
• 2 sizes for MK-3 and MK-4 canisters • Covered hole in back allows baton to be placed in
pouch fully expanded
• Sturdy web belt loop
• Fits Monadnock® AutoLock® HG baton 21" only
• Dual web belt loop fits both 2" (50mm) and 2.25" (58mm)
belts
7907 oc/Mace ®
spray Holder 7913 Expandable Baton Holder
• 2 sizes for MK-3 and MK-4 canisters • 2 sizes for 21" and 26" batons: Monadnock®, ASP®
and similar
• Dual web belt loop fits 2" (50mm) and 2.25" (58mm)
• Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts belts
7913as auto-open Baton Holder 7916 silent Key Holder 7915 Pager/glove Holder
• Adjustable swivel mount • Roll Top™ wraparound design • Holds most standard pagers or two pair latex gloves
• Baton fully extends as it is being drawn from • Hook & loop closure • Chrome, brass or hidden snap
the holder
• Dual web belt loop fits 2" (50mm) and 2.25" (58mm)
• Fits Monadnock® AutoLock® HG 21" baton only belts
• Trilaminate construction with Duraskin™
finish and Coptex™ knit lining
7904 side-Handle Baton Holder 7929 cell Phone Holder 7906 Belt Keeper
• Fits straight and side-handle batons • Fits Nextel i205 and similar • 1" width available in chrome, brass or hidden snaps
• Sturdy, injection-molded ring • Hook & loop closure • Sold in 4-pack
• One-way snap-on belt loop • Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts

DUTY ACCESSORIES
PaTENTEd
PaTENTEd 8018 ultimate Hinge Handcuff case

8014/8014s universal radio Holder • Holds one pair Safariland 8142 cuffs
• Holds most hand-held radios
• Dual web belt loop fits 2" (50mm) and
• Adjustable elastic security strap with snap closure 2.25" (58mm) belts
2.25" (58mm) belts
• 8014S features a two-piece adjustable swivel base and
mount
PatrolTek ™
8000 covered Handcuff case

PaTENTEd
8034 open Top Handcuff case

PaTENTEd
• With significant cost savings compared to • Holds one pair standard cuffs • Pull-through style
premium brands, PatrolTek™ also offers the quality
and functionality you’ve come to expect from • Hidden snap closure • Holds one pair standard cuffs
Bianchi® • Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts • Dual web belt loop fits both 2" (50mm)
• Contour molded technology and 2.25" (58mm) belts
• Pleated pouch lids offer a smooth closure and
great fit
• Reinforced snap closures
• Trilaminate with 600-denier woven finish
• Dual belt loop design lets same pouch be used for
2" (50mm) and 2.25" (58mm) belts (most models)
• Lightweight and weatherproof
• Easily cleaned with soap and water
PaTENTEd
• Stays flexible in cold weather
8017 double Handcuff case 8038s rigid Handcuff case

• Holds 2 pair standard cuffs • Holds one pair Safariland™ model 8132 Rigid
Cuff or similar
• Hook & loop closure
• Adjustable swivel mount
• Contour molded for long-lasting shape and
precise fit
PaTENTEd
PaTENTEd
8001 single Handcuff case with Key slot 8010 Mini-Light Holder
• Hidden snap closure • Fits AA-cell lights
• Holds one pair standard cuffs • Hook & loop or hidden snap closure
• Slot to hold spare cuff key in lid • Dual web belt loop fits both 2" (50mm) and 2.25" (58mm) belts
• Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts • Also available in OD
PaTENTEd PaTENTEd PaTENTEd
8027 rail Mounted Light Holder 8011 compact Light Holder 8007 oc/Mace ®
spray Holder
• Hook & loop closure • Hidden snap closure • 2 sizes for MK-3 and MK-4 canisters
• Dual web belt loop fits both 2" (50mm) and • Full flap helps secure light • Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts
2.25" (58mm) belts
2.25" (58mm) belts
PaTENTEd
8026 compact Light Holder 8009 flashlight ring 8008 open Top oc/Mace ®
Holder
• Two sizes fit most 1" diameter lights • 1" web • 2 sizes for MK-3 and MK-4 canisters
• Holds all flashlight lengths • Molded plastic ring locks flashlight in position • Open-top design for quick access
• Dual web belt loop fits both 2" (50mm) and • Fits D-cell lights • Dual web belt loop fits both 2" (50mm)
2.25" (58mm) belts • Available in sewn or snap version and 2.25" (58mm) belts

DUTY ACCESSORIES
PaTENTEd PaTENTEd
8013as auto-open Baton Holder 8003 single Magazine Pouch

• Adjustable swivel mount • Hook and loop or hidden snap closure
• Baton fully extends as it is being drawn from the holder • Dual web belt loop fits 2" (50mm) and 2.25" (58mm) belts
• Trilaminate construction with Duraskin™ finish and
Coptex™ knit lining
• Fits Monadnock® AutoLock® HG Baton 21" only
PaTENTEd
PaTENTEd
8012 Expandable Baton Holder 8002 double Magazine Pouch

• Baton holder w/ hole in back for reholstering expanded baton • Vertical or horizontal carry offers versatility of use
• Three sizes to fit 16", 21" and 26" batons, including • Hidden snap closure
Streamlight® Super Stinger and Monadnock® & similar
• Dual web belt loop fits both 2" (50mm) &
2.25" (58mm) belts
PaTENTEd
8013 Expandable Baton Holder 8020 Triple Threat ™

ii double Magazine Pouch
• 3 sizes for 16"-21" & 26" batons • Injection-molded belt loop for vertical or horizontal
carry
• Also fits Streamlight® Super Stinger
• Tension screw adjustment permits various
• Dual web belt loop fits both 2" (50mm) and 2.25" (58mm) belts drawing angles
PaTENTEd PaTENTEd
8013s Expandable Baton Holder with swivel 8029 cell Phone Holder
• Adjustable swivel mount • Designed for the Monolith phone
• Can be used with Monadnock® Hindi Baton Cap™ • Flap closure with hook & loop
• Dual web belt loop fits both 2" (50mm) and 2.25" (58mm) belts • Dual web belt loop design fits both 2" (50mm)
and 2.25" (58mm) belts
PaTENTEd PaTENTEd
8015 Pager/glove Holder 8016 silent Key Holder 8006 Belt Keeper
• Hidden snap closure • Holds keys securely and silently • 1" web
• Dual web belt loop fits 2" (50mm) and 2.25" • Wraparound hook & loop closure • Black finished brass snaps
(58mm) belts
• Dual web belt loop fits 2" (50mm) and 2.25" (58mm) • Sold in 4-pack
belts
8028 flat glove Holder 8006i slide-on Belt Keeper

• Holds 2 pair of latex gloves • 1" web
• Trim and compact • Keeps duty belt secure to liner belt
• Dual web belt loop fits both 2" (50mm) and 2.25" • Black finished brass snaps
(58mm) belts

6355
aLs Tactical Holster with
®
Quick-release Leg strap

simple straight up draw once release is
deactivated
• Open-top design without SLS for quick
retrieval of weapon
• Hood Guard is standard
construction protects handgun
and sights
THE TacTicaL
TACTICAL & MILITARY
adVaNTagE shroud with mounting holes for optional
accessories
Tactical officers are a breed apart. And so
is Safariland tactical gear. We understand • Adjustable vertical leg strap with quick-
release detachable leg harness
that there is no margin of error in your
work. And we design our products • Suede lined to protect handgun’s finish
accordingly. That’s why Safariland • Leg shroud features silicon strap for
offers an unmatched combination of non-slip traction
quality, functionality and versatility in • Available in STX Tactical® Black,
every product that carries our name. Our Foliage Green, OD Green and FDE
Brown finishes
products are battle-proven worldwide.
From leg-drop holsters and MOLLE
attachment systems to munitions carriers
and more, Safariland gives you the tactical PaTENT PENdiNg
advantage you need to carry the day – day
in and day out.
TacTicaL HoLsTEr
coLor oPTioNs:
fdE BrowN
BLacK
od grEEN
foLiagE grEEN
PaTENT PENdiNg PaTENTEd
6354 aLs ®
Tactical Holster 6004 sLs Tactical Holster
• ALS (Automatic Locking System)
®
• Adjustable vertical leg strap • SLS allows for a smoother, single-motion • Standard double leg strap and leg shroud
secures weapon once holstered; draw and greater protection against with mounting holes for optional accessories
simple straight up draw once release • Standard double leg strap and leg attempted weapon takeaways
is deactivated shroud with mounting holes for • Offered for weapons with and without
optional accessories • Features the SLS (Self Locking System) rail mounted lights
• Open-top design without SLS for rotating hood system
• Suede lined to protect handgun’s finish • Suede lined to protect handgun’s finish
quick retrieval of weapon • Hood Guard is standard
• Leg shroud features silicon strap for • Leg shroud features silicon strap for non-
• Hood Guard is standard • Thermal-molded SafariLaminate™ slip traction
non-slip traction
• SafariLaminate thermal-molded
™ construction protects handgun and
• Available in STX Tactical® Black, sights • Available in STX Tactical® Black, Foliage
construction protects handgun and Green, OD Green and FDE Brown finishes
sights Foliage Green, OD Green and FDE
Brown finishes
shown here with optional douBLE

MagaZiNE pouch mounted (see page 28)
PaTENTEd
6005 sLs Tactical Holster with Quick-release Leg Harness

• Features the SLS (Self Locking • Adjustable vertical leg strap with
System) rotating hood system quick-release detachable leg
harness
• SLS allows for a smoother, single-
motion draw and greater protection • Offered for weapons with and
against attempted weapon without rail mounted lights
takeaways
• Suede lined to protect handgun’s
• Hood Guard is standard finish
• Thermal-molded SafariLaminate™ • Leg shroud features silicon strap for
construction protects handgun and non-slip traction
sights
• Available in STX Tactical® Black,
• Standard double leg strap and leg Foliage Green, OD Green and FDE
shroud with mounting holes for Brown finishes
optional accessories

TACTICAL & MILITARY
6305
aLs /sLs Tactical Holster with
®
Quick-release Leg Harness
• ALS® (Automatic Locking System) secures

weapon once holstered
• Includes SLS hood assembly
• Hood Guard is standard
• Mounted to the same leg shroud assembly
as the popular 6005 series
• Simple straight up draw once all releases
are deactivated
construction protects handgun and sights
shroud with mounting holes for optional
accessories
• Adjustable vertical leg strap with quick-
release detachable leg harness
• Offered for weapons with and without rail
mounted lights
• Suede lined to protect handgun’s finish
PaTENTEd & • Leg shroud features silicon strap for non-slip
PaTENT PENdiNg traction
• Available in STX Tactical® Black, Foliage
Green, OD Green and FDE Brown finishes
6304 aLs /sLs Tactical Holster

®
Mounted to the same leg shroud

assembly as the popular 6004 series
PaTENTEd
6035 NEw sLs Military 6235 NEw sLs Low-ride

Tactical Holster Military Holster
Adjustable vertical leg strap 1.5" (38mm) Belt Drop version
with quick-release detachable
leg strap version
6034 NEw sLs Military Tactical Holster 6230 NEw sLs Mid-ride Military Holster
• Designed to accommodate the Beretta M9/ • Thermal-molded SafariLaminate™ • Designed to accommodate the • Thermal-molded SafariLaminate™
92F or Sig P226 pistol with or without a light construction protects handgun and sights Beretta M9/ 92F or Sig P226 pistol construction protects handgun and
or LAM unit with or without a light or LAM unit sights
• Ambidextrous body design shroud with mounting holes for optional • Ambidextrous body design • Available in STX Tactical® Black,
accessories Foliage Green and FDE Brown
• Features the SLS (Self Locking System) • Features the SLS (Self Locking finishes
rotating hood system • Available in STX Tactical® Black, Foliage System) rotating hood system
Green and FDE Brown finishes
• SLS allows for a smoother, single-motion • SLS allows for a smoother, single-
draw and greater protection against motion draw and greater protection
attempted weapon takeaways against attempted weapon takeaways
PaTENTEd PaTENTEd
6074 raptor ™
Tactical Holster 6274 raptor ™
Tactical Holster
• Middle finger release tab • Standard double leg strap and leg • Features the SLS (Self Locking System) • Standard double leg strap and leg shroud
shroud with mounting holes for optional rotating hood system with mounting holes for optional accessories
• Features the SLS (Self Locking accessories
System) • Hood Guard is standard • Same holster body as 6270
• Suede lined to protect handgun’s finish
• Mounted to the same leg shroud as • Rock slightly back to draw • Suede lined to protect handgun’s finish
the 6004 • Leg shroud features silicon strap for
non-slip traction • SLS allows for a smoother single-motion • Leg shroud features silicon strap for
• Hood Guard is standard draw and greater protection against non-slip traction
• Available in STX Tactical® Black, attempted weapon takeaways
• Same holster body as 6070 Foliage Green, OD Green and FDE • Available in STX Tactical® Black, Foliage
Brown finishes • Thermal-molded SafariLaminate™ Green, OD Green and FDE Brown finishes
construction protects weapon
3085 Military 3285 Military

Tactical Holster drop Holster
Adjustable vertical leg
strap with quick-release 1.5" (38mm) Belt Drop version
detachable leg strap
version
3084 Military Tactical Holster 3280 Military Mid-ride Holster

• Designed to accommodate the Beretta • Thermal-molded SafariLaminate™ • Designed to fit the Beretta M9 or 92F pistol • Works with the Safariland MOLLE Locking
M9 or 92F pistol with or without a light construction protects handgun and sights with or without a light or LAM unit System (MLS)
or LAM unit
• Standard double leg strap and leg • Forward rotating hood allows for a smooth • Available in STX Tactical®, Foliage Green,
•Forward rotating hood allows for a shroud with mounting holes for optional single-motion draw and greater protection OD Green and FDE Brown finishes
smooth single-motion draw and greater accessories against attempted weapon takeaways
protection against attempted weapon
takeaways • Works with the Safariland MOLLE • Ambidextrous; utilizes a simple rotating
Locking System (MLS) hood design that can be changed from
• Ambidextrous; utilizes a simple rotating right to left
hood design that can be changed from • Available in STX Tactical® Black,
right to left Foliage Green, OD Green and FDE
Brown finishes
TACTICAL & MILITARY
6005-10
single strap Leg shroud
with detachable Buckle
(shown with accessories attached)
• Lower profile leg shroud designed
primarily for EDW units
• Can mount accessories on both sides
38-8 of holster, or used for 3 accessories
37-8
• Adjustable vertical leg strap to
adjust ride height
• Removable buckle system for
ease of mounting to leg
• Leg shroud features silicon strap for
non-slip traction
• DFA (Drop Flex Adapter) can be used
• Available in STX Tactical® Black,
Foliage Green, OD Green and FDE
Brown finishes
38-8 impact round Holder 37-8 open Top impact round Holder
• Closed top holder for 37/40mm less lethal rounds • Open-top holder for 37/40mm less lethal rounds
• Designed for the eXact Impact and Direct Impact
™ ®
• Can be ordered for 2.25" (58mm) belt slide or mount on
rounds leg and vest accessory
• Can be ordered for 2.25" (58mm) belt slide or mount on • Available in STX Tactical® Black, Foliage Green and FDE
leg and vest accessory Brown finishes
• Available in STX Tactical® Black, Foliage Green and • Can be ordered with MLS 16 Locking Fork attached
FDE Brown finishes
• Can be ordered with MLS 16 Locking Fork attached
(shown with accessories attached)

6004-6
Harness and shroud
• Features harness and shroud only to

mount accessories
• Ambidextrous
• Available in Black, Foliage Green,
OD Green and FDE Brown finishes
76 772 38
76 single Mag Pouch 772 single Mag Pouch 38 oc spray Holder

• Single mag pouch with flap for • Single mag pouch with flap for • Single OC spray pouch for
multiple handgun models H&K MP5 and Colt AR15 for multiple sizes
right and left hand shooters
• Available in STX Tactical® Black, • Available in STX Tactical®
Foliage Green and FDE Brown • Available in STX Tactical® Black, Black, Foliage Green and
finishes Foliage Green and FDE Brown FDE Brown finishes
finishes
• Can be ordered with MLS 16 • Can be ordered with MLS 16
Locking Fork attached • Can be ordered with MLS 16 Locking Fork attached
Locking Fork attached
shown here with
optional ELs 35
silicon-lined strap for non-slip traction. receiver Plates
(see page 61)
6004-10 single Leg strap shroud 6005-6 Quick release Leg shroud 6004-27 drop flex adapter
on single Leg shroud w/ QLs 22
• Lower profile leg shroud designed primarily • Features harness and shroud only to mount accessories • Allows user to wear a thigh rig higher on the leg with
for EDW units and holsters more stability, eliminating leg shroud movement
• Can mount accessories on both sides of • Leg shroud features silicon strap for non-slip traction • Sits low enough for use with body armor and in vehicles,
holster, or used for 3 accessories while also providing two mounting points for accessories
• Ambidextrous
• Adjustable vertical leg strap to adjust ride height • Includes QLS 22 Receiver Plate (can also be ordered
• Available in Black, Foliage Green and FDE Brown finishes with MLS Receiver Plate or plain)
• DFA (Drop Flex Adapter) can be used
• For use on belt widths up to 2.25" (58mm)
• Available in Black, Foliage Green and FDE
Brown finishes • Available in Black, Foliage Green and FDE Brown finishes
6005-23 MLs accessory forks on Quick

release Harness
• Allows mounting of the 6005 Tactical Holster directly
to the MOLLE loops on the side of a vest or MOLLE
web belt
(shown on shroud with holster) • Enables user to forgo wearing a belt and put the
weight onto a load-bearing vest and thigh rig
• Ideal for combining with a tactical vest without having
to make any changes to a duty belt to be ready as a
first responder
6005-11 Leg strap only with Quick release

• Fits tactical holster systems
• Replacement strap for Quick Detach tactical rig straps
• Converts tactical rig straps to Quick Detach straps
• Available in Black, Foliage Green or FDE Brown finishes
6005-7 Quick release Harness– Top Portion only

• Fits tactical holster systems
• For harness and shroud only to mount accessories
40 77 and holsters
• Ambidextrous
40 distraction device Holder 77 double Magazine Pouch • Available in Black, Foliage Green or FDE Brown finishes
• Distraction Device® Holder • Double mag pouch with flap for (order 6005-23)
to fit Defense Technology™ multiple handgun models
OmniBlast 100
• Distraction Device® Holder
• Available in Black, Foliage 6004-11 Leg strap only
Green or FDE Brown finishes • Fits tactical holster systems
Complete for Defense
Technology #25 • Can be ordered with MLS 16 • Replacement strap for standard tactical rigs
• Available in Black, Foliage • Available in Black, Foliage Green or FDE Brown finishes
Green or FDE Brown finishes
• Converts Quick Detach tactical rig straps to standard
• Can be ordered with MLS 16

TACTICAL & MILITARY
4014 ar single Point sling with shoulder Pad 4017 NEw single Point sling for Launchers
• Convenient single point AR15 sling for carbine butt stock • Convenient, single point M79 and multiple projectile
grenade launcher sling
• Makes for an easy transition from low ready, to firing,
to placed on the back for use of hands • Makes for an easy transition from low ready, to
• Sling slides freely on the shoulder due to an innovative firing, to placed on the back for use of hands
floating shoulder pad • Made out of durable nylon
• Made out of durable nylon • Quick-detach system makes it easy to remove
launcher from sling without use of tools
4015 ar15 sling system 4016 ar15 single Point sling

QuicK dETacH sYsTEM • Convenient single point AR15 sling carbine butt stock • Convenient single point AR15 sling carbine
butt stock
• Makes for an easy transition from low ready, to firing, to
• Quick detach system featured on all single point placed on the back for use of hands • Makes for an easy transition from low ready,
sling models to firing, to placed on the back for use of
• Sling slides freely on the shoulder due to an innovative hands
• 180° twist locks and unlocks system floating shoulder pad
• Made out of durable nylon
• Made out of durable nylon
• Includes AR15 double magazine pouch
4018 NEw dual Point sling 176 Extreme duty Magazine Pouch 774 rifle Mag Pouch
• Convenient dual point grenade launcher and • Pivots away from body to prevent interference with • Clip-on belt attachment to fit 1.5" (38mm) to 2.25"
long gun sling body armor (58mm) belts
• Makes for an easy transition from on the • Spring loaded to lift magazine above other duty gear on belt • Adjustable for carry angle
back to firing
• Magazine is secure in pouch in inverted position with • SafariLaminate™ construction with tension device
• Uses traditional dual sling mounts securing strap removed
• Ambidextrous
• Made out of durable nylon • Securing strap releases with one finger
• Available in Black, Foliage Green or FDE Brown finishes
NEw dual Point sling with

4019 shoulder Pad 7742 Magazine doubler rK-M4 fore End rail Kit
• Convenient dual point grenade launcher and • Quick, efficient reload with second magazine • Allows for quick attachment of 3 rails to forward end of
long gun sling AR15, M4 and M-16 rifles
• Proper staggering of magazine to clear ejection port
• Shoulder pad for increased comfort • Can attach 2 accessories to upper forearm and 1 to
• 2 top round protectors keep cartridges in proper bottom rail
• Makes for an easy transition from position and dirt out of magazines
on-the-back to firing position • Lightweight
• Protects base pad of magazine when dropped
• Uses traditional dual sling mounts • Can be reversed to have one rail on top with 2 below
• Does not crush magazine
• Made out of durable nylon • Locks securely into place use holes in standard fore end
• Excellent for seated and prone shooting positions

TACTICAL & MILITARY
4552 NEw dual rifle case
• Rugged ballistic pack cloth construction
• Heavy-duty zippers, one adjustable outside covered
accessory pouch
• Large dual handgun/accessory pouch with
individual hook & loop enclosed handgun areas
• Closed-cell foam padding, 2" padded interior
perimeter lip, detachable padded, adjustable
shoulder harness, inside shoulder harness storage
pocket
• Inside assorted accessory pockets and outside
universal attachment straps for backpack-style
carry (shown with optional safariland accessories
• 36" length: Optimized for M4/CAR15 style weapons and ProTech® brand pouches)
• 46" length: Optimized for M1a/AR15/full length bolt
style weapons
4555 NEw shooters’ range Bag

• Removable center carry compartment
has zippered, padded side panels for 4
separate handgun compartments
• Adjustable hook & loop dividers to
personalize accessory space
• Removable and adjustable storage loops
for extra magazines
• Full-wrap carry handles make it easy to
move gear to different shooting stations
• Outer carry bag has dual zipper top
for easy access and full coverage, flat
side zipper pocket, ID window, and
large outside zippered pocket for towel,
shooting glasses or hearing protection
• Overall dimensions: 14" x 9" x 10"
4554 NEw rifle scope guard
• Durable pack cloth construction
• Padded cover to protect the vulnerable optics on a weapon
• Includes an adjustable, removable muzzle protector
• Web carry handle for ease of travel
4000 dust cover

• Nylon cover is durable and keeps dirt out of the muzzle and
action of the firearm
4553 NEw 12" Premium dual Handgun case • The tab provided makes it easy to cover and uncover with
one hand
• Rugged ballistic pack cloth construction • Lanyard strap can easily be attached through a thigh rig or
anywhere a nylon loop can be fastened
• Full interior closed-cell foam surrounded by
soft lining for safe handgun storage • An elastic outer ring in the cover keeps the unit snug around
the firearm, preventing rain or snow from falling onto the
• Four outside magazine/accessory pouches firearm
• Wraparound handles
4145 Munitions Butt stock caddy

• For 37/40mm impact rounds and 12-gauge rounds
• Elastic straps to fit many butt stocks
4385 Munitions Belt • Holds (3) 40mm or (5) 12-gauge rounds
• For 37/40mm impact rounds and 12-gauge

rounds 4147 shotgun shell Holder (Not shown)
• Holds (20) 40mm or (25) 12-gauge rounds
• Holds 5 12-gauge rounds
• Belt size – fits sizes 32" (812mm) to 50"
(1270mm) • Screws on to a tactical shroud or ELS 35 Receiver Plate
• Nylon cover with hook & loop closure

TACTICAL & MILITARY
uM84
universal Military Holster
• Commercial offering of the

military standard issue M12
holster
• System can be worn 14 different
ways
• Removable flap for conversion to
thumb break
• Ambidextrous design
• Converts to shoulder holster with
optional UM84H Harness
• Equipped with Quick-Lock™ belt
fastener
• Includes field cleaning rod
• Available for revolvers and
semiautos
• Fits up to 2.25" (58mm) belt
u.s. aNd forEigN PaTENTs
uM84 ii
(sHowN)
uM84i uM84iii
BLacK dEsErT
uM92
universal Military Holster
• Commercial offering of the military

standard issue M12 holster with the
addition of a polymer trigger guard
insert that stabilizes the trigger guard
of certain large frame autos; ideal for
Sig Sauer and Glock weapons
• Ambidextrous
uNiVErsaL digiTaL od grEEN • Equipped with Quick-Lock™ belt
caMo fastener
• Compatible with all UM84
accessories
Military Product color offerings • Fits up to 2.25" (58mm) belt
ModEL fiNisH
UM84I Black, OD, Woodland Camo, 3 Color Day
Desert Camo, Universal Digital Camo
UM84II Black, OD, Woodland Camo, 3 Color Day
Desert Camo
UM84III Black, OD, Woodland Camo, 3 Color Day
Desert Camo
UM84R Black, OD, Woodland Camo
UM92I Black, OD, 3 Color Day Desert Camo
UM92II Black, OD, 3 Color Day Desert Camo
M12 OD
M13 Black, OD
M1415 Black, OD
M1020 Black, OD, Foliage
M12 universal Military Holster uM84r universal Military Holster M1430 NEw universal Military adapter
• U.S. Armed Forces standard issue for the • Commercial offering of the military standard issue M12 • Adapter kit allows MLS 15 Locking Fork to attach
Beretta M9 sidearm holster for revolvers to the back of the UM84/UM92 Universal Military
Holsters
• Removable flap for conversion to thumb break • Converts to shoulder holster with optional UM84H
• Locking Fork allows the holster to be mounted
• Ambidextrous design • Removable flap for conversion to thumb break directly into MOLLE loops or into an MLS 17 or MLS
• System can be worn 14 different ways • Ambidextrous 18 Receiver Plate
• Converts to shoulder holster with M13 or • Includes field cleaning rod • Allows quick switching of holster from leg to vest or
UM84H any other mounting point
• Equipped with Quick-Lock belt fastener
™
• Equipped with Quick-Lock™ belt fastener • Designed to break away at the military-specified
• Fits up to 2.25" (58mm) belt pressure of 140 lbs.
• Hard action snaps for extra security
uM84H underarm shoulder Harness M1415 Thumb snap system M13 chest Harness
• Converts hip holster to shoulder holster to be • For use when flap is removed from UM92/UM84/M12 • Cross-chest design is ideal for helicopter and
carried in vertical position other close-quarter use
• Offers faster performance in tactical situations
• Ambidextrous design; fully adjustable • Ambidextrous design
• Provides added retention
• To be used without holster flap • Completely adjustable
• Available in Black and OD
• Fits up to 48" (122cm) chest • Dual positioning
• Available in Black and OD

TACTICAL & MILITARY
T6510
Modular accessory Panel
• Five attachment points to mount

accessories (two are bi-directional)
• Adjustable ambidextrous leg strap
with 2" quick-release buckle for quick
deployment
• Hook & loop vertical adjustment
to custom-tailored panel location
on thigh
• Non-slip Gription™ mesh backing
keeps panel securely in place on leg
• Web attachment points for use with
Bianchi® military holster with
Quick-Lock™ belt fastener
PaTENTEd
7200/7120 accuMold ®
od duty Belt rig
• A select group of our best-selling AccuMold items

available in OD Green
• Featuring our 7120 Defender® duty holster for the
Beretta 92 & Glock 17/22. Models offered are those
shown
• Special order item; see your dealer for availability
PaTENTEd PaTENTEd
T6500 Tac Holster LT T6505 Tac Holster T6521 double ar15 Pouch
• Adjustable to fit most pistols with tactical lights mounted • Quick-Lock™ clip for attachment to T6510 Accessory • Holds two 30-round AR15-type magazines
Panel, to any MOLLE attachment system or on an
• Quick-Lock™ belt clip for attachment to T6510 equipment belt up to 2.25" (58mm) wide • Quick-Lock™ belt clip for secure attachment
Accessory Panel, to any MOLLE attachment system or
to an equipment belt up to 2.25" (58mm) wide • Features polymer trigger guard shield that protects • Dual hook/loop and snap closure for added
and stabilizes security
• Secondary retainer strap for a double lock on the thumb
break for additional retention when required • Rugged Ranger™ trilaminate construction • Rugged ballistic trilaminate construction
• Rugged Ranger™ trilaminate construction • Ambidextrous • Available in Black Ballistic Weave finish
• Available in Black Ballistic Weave finish • Available in Black Ballistic Weave finish
M1020 web Pistol Belt

• Tough mil-spec nylon construction
• Official military plastic buckle
• One size fits 30"-48" (76cm-122cm) lengths and
2.25" (58mm) width
• Available in Black and OD Green
M1425 Tactical Hip Extender M1030 Military Magazine Pouch M1025 Military Magazine Pouch
• Provides a rigid platform and upper • Holds four magazines • Holds two magazines
attachment point for accessories • Trim & compact
• Trim & compact
• Includes a high-mounted leg strap • Quick-Lock™ belt fastener attaches securely to
• Quick-Lock™ belt fastener attaches securely to
• Features Quick-Lock™ belt fastener web belt web belt
• Fits up to 2.25" (58mm) belt • Fits up to 2.25" (58mm) belt • Fits up to 2.25" (58mm) belt
• Available in Black, Universal • Available in Black, 3 Color Day Desert Camo, • Available in Black, 3 Color Day Desert Camo,
Digital Camo OD Green Universal Digital Camo, OD Green

• Provides a holster or accessory with a quick, easy, and
secure attachment to any MOLLE loop-equipped apparel
• Allows for quick removal and installation between
attachment points such as the MOLLE vest, belt loop, and/
or tactical leg shroud
• May be used to mount in vehicle, home or business
• Allows many types of Safariland holsters and accessories
to be mounted at various orientations and angles to suit
the needs and preferences of the individual user
• Allows the user to rearrange gear quickly and easily
without the use of tools
• Allows holstered weapons and accessories to be removed
without removing apparel, such as vest, leg shroud, or belt
• Product is secured using a very small, 2" x 2" “footprint” on
the apparel
• Allows user to mount almost any holster or accessory in
Safariland’s Quick Attachment Systems,
QUICK ATTACHMENT SYSTEMS
the right position for any mission
consisting of the MLS, QLS, and ELS, represent
the coming together of technology with the
requirement for modular and versatile products.
Originally designed for the military to quickly
transfer the holster from the leg to the vest,
the QAS family has now gone beyond strictly • The QLS provides officers the ability to easily and quickly
remove and secure their weapon without having to
military functions to include law enforcement, remove gun or electronic discharge weapon (EDW) from
concealed carry, and sporting applications. holster. Especially effective in correctional institutions and
Whether the scenario facing you involves the courthouse appearances
need to adjust holster location to conserve • Also effective for concealed carry in ease of transferring
space while boarding an APC or to quickly gun from body to other mounting point, such as vehicle
switch out magazine types before the latest • Allows the user to mount almost any Safariland duty holster
IPSC match, the QAS family of products will on an equipment belt with use of the Safariland UBL
help accomplish your goals. • Provides a highly versatile holster system with a quick,
easy and secure attachment to a variety of locations – belt,
thigh rig, furniture, or vehicle. Can also be used with the
Safariland MLS 16 Accessory Locking Fork for attachment
to MOLLE vests
• QLS System passes Level I Retention™ pull test
NEw
• Provides a mounting platform for any tactical accessories
to be placed in various locations, including belt clips and
tactical rigs or directly on MOLLE loops with the use of an
MLS 16 Locking Fork
• Fork attaches to any tactical accessory, including the 774
Rifle Mag Pouch, 78 Slimline Dual Magazine Pouch, and
Impact Round cases
• Receiver plate mounts to any thigh rig, 744BL belt clip or
MLS 16 fork, or can be attached directly to the pre-cut
mounting holes on the 4332 Tactical Belt or 032 Competition
Belt
• A quick pinch of the thumb and index finger allows the
removal of any product attached to the fork unit for
attachment on any other ELS 35 location
• May be purchased or placed directly onto the 744BL belt
clip for convenient waistline location
• Useful in quickly switching out accessories while
maintaining the same root product, whether it be a belt,
thigh rig, etc.
• Very small receiver footprint (1 7/8" W x 2 3/4")
MLs 15 & 16
1 MLs 15 Holster Locking fork
• Mounts directly to the back of holsters and
threads through MOLLE loops or connects to the
MLS 17 or MLS 18 Receiver Plates
• Colors: Black, Foliage Green, OD Green,
FDE Brown
2 MLs 16 accessory Locking fork

• Threads directly through MOLLE loops to mount
pouches, or into the back of the MLS 17 Receiver
Plate for attachment of pouches or holsters
1 2 FDE Brown
MLs 17 & 18
1 MLs 17 receiver Plate
• Mounting platform for the MLS 15 and MLS
16 Locking Forks. Attaches directly to leg
drop shrouds, MLS 16 Locking Fork, or
other platforms, such as vehicle or furniture
FDE Brown
2 MLs 18 receiver Plate with guard

• Mounting platform for the MLS 15 and MLS 16
Locking Forks. Attaches directly to belt slide
1 2 and paddle holsters for use on belts
FDE Brown
QLs 19 & 22 for duty use – Passes Level i retention ™

Test
1 QLs 19 duty Holster Locking fork

• Mounts directly to the back of duty holsters, then
connects to the QLS 22 Receiver Plate
• Colors: Black, Foliage Green, OD Green, FDE Brown
2 QLs 22 duty receiver Plate

• Mounting platform for the QLS 19 Duty Locking Fork.
Attaches directly to Universal Belt Loop (UBL)
• Colors: Black, Foliage Green, OD Green, FDE Brown
1 2 3 QLs 22L duty receiver Plate (not shown)

• Same as the QLS 22 with an extra locking feature
ELs 34 & 35
1 ELs 34 Equipment Locking fork
• Mounts to any tactical accessory, then
connects to the ELS 35 Receiver Plate
FDE Brown
2 ELs 35 Equipment receiver Plate

• Mounting platform for tactical thigh rig or
any other two-hole accessory location
FDE Brown
1 2

QUICK ATTACHMENT SYSTEM
Law ENforcEMENT/MiLiTarY
1 2 3
QLs oN a duTY BELT

1. QLs 22 w/ uBL oN BELT
2. QLs 19 oN HoLsTEr BacK
3. QLs 19 w/ uBL w/ HoLsTEr oN QLs 22
1 2 3
MLs oN a MoLLE VEsT

1. MLs 16 oN VEsT
2. MLs 16, MLs 17 oN VEsT
3. MLs 15, MLs 16, MLs 17 w/ HoLsTEr
1 2
MLs oN a droP LEg

1. MLs 17 oN LEg sHroud
2. MLs 17 w/ MLs 15 oN HoLsTEr
1 2 3
ELs oN a siNgLE LEg sHroud

1. ELs 34 oN LEg sHroud
2. ELs 34 w/ 774 6005-23 MLs accessory fork on Quick
release Harness
3. ELs 34 w/ 774 w/ ELs 35 oN LEg sHroud
• Allows mounting of the 6005 Tactical Holster directly into
the MOLLE loops on the side of a vest or MOLLE web belt
• Enables user to forgo wearing a belt and put the weight
onto a load-bearing vest and thigh rig
coNcEaLMENT • Ideal for combining with a tactical vest without having

to make any changes to a duty belt to be ready as a
first responder
1 2 3
MLs iN VEHicLE
1. rEMoViNg HoLsTEr froM MLs 18
2. HoLsTEr w/ MLs 15 oN BELT wiTH MLs 18
3. TraNsfErriNg HoLsTEr To MLs 17 MouNTEd iN VEHicLE
6004-24 MLs accessory fork on small

MoLLE Plate
• A mount with the MLS 16 Accessory Fork already
affixed; attaches to existing MOLLE pouches, then is
easily threaded through MOLLE loops
• Can be attached to an MLS 17 or MLS 18 Receiver
Plate, then mounted on a MOLLE vest, thigh rig, belt,
or other attachment point
• Allows the user to rearrange gear quickly and easily
1 2 3
MoLLE-KiT 1 (NoT sHowN)

• Includes the MLS 15, MLS 16, MLS 17, MLS 18 and
mounting hardware
QuicK-KiT 1 (NoT sHowN)

MLs oN coNcEaLMENT HoLsTEr PaddLE or BELT sLidE • Includes the QLS 19, QLS 22, and mounting hardware
1. MLs 18 coNNEcTEd To PaddLE
2. MLs 15 coNNEcTEd To HoLsTEr
3. MLs 15, MLs 18 coNNEcT PaddLE aNd HoLsTEr
ELs-KiT NEw (NoT sHowN)
• Includes 2 ELS 34 units and 2 ELS 35 units and
mounting hardware

raPid LigHT sYsTEM (rLs™)
With the Safariland Rapid Light System (RLS™), you get a professional-quality hand-held light and
weapon-mounted light all in one. You can clip it onto your belt, hold it in your hand, or quickly
mount it to your weapon for an instant tactical advantage. There’s no need to buy an expensive
holster to carry a light-mounted weapon. No reason to carry a second primary light. You will
always have a bright light whenever and wherever you need it. It’s the only light you need.
attaches To gun in 2 Easy steps:

The rLs can be instantly removed if an immediate reholstering of the pistol is required.
RLS/MOUNTS
LocK rLs iNTo PLacE
wiTH a QuicK uPward
sLidE rLs oNTo MoTioN
TacTicaL raiL
Easily and securely Push-button illumination 3 aaas provide over 50

attaches to waistband or hours’ use
belt with integral clip
5
6 1
scoPE MouNTs
Safariland AR15 mounts are designed specifically for
flat-top receivers with Picatinny rails. Machined from
6061-T6 aluminum, Safariland AR15 mounts have
NOT SHOWN AT ACTUAL SIZE skeletonized top caps and bases that reduce weight
without sacrificing strength. Each top cap is secured by
four screws to provide maximum clamping ability to
prevent movement of the scope or red dot sight. The
corners are rounded to remove sharp edges and lessen
the chance of snagging on other gear and webbing. The
2 mounts are secured to the receiver with mil-spec thumb
4 3 knobs with anti-vibration washers that can be tightened
7 by hand or with a regular screwdriver.
PaTENTEd
8
1. Ambidextrous. 6. Quickly transitions from standard flashlight to
tactical illumination.
2. Super-bright LED technology (90 lumens) – bright
enough to be your primary light. Prism Reflector 7. Can be operated with either thumb, or change
System penetrates light up to 350 feet. to other side to operate with trigger finger. Push
button provides controllable on/off illumination of
3. 3 AAAs provide over 50 hours’ use–no expensive target to minimize loss of handgrip, sight picture
proprietary batteries needed. and exposure.
4. Integral clip for easy securement to belt or garment 8. RLS™ mount will accommodate most hand-held
saf-s30 NEw
– no dedicated light mount holster required. compact lights in the range of .970 (24.6mm)-1.060
(26.9mm) in diameter. • Designed for 30mm red dot sights requiring single ring mounting
5. Fits most handgun models that incorporate an • Provides maximum stability and strength for attaching to the
integral rail system – also mounts to rifles and receiver
shotguns that have a Picatinny rail.
• Available in Black and FDE Brown
saf-s30c NEw
• Single ring mount is cantilevered forward to enable the use of
night vision or magnifiers
• Design provides maximum stability and strength for attaching
to the receiver
(rLs™ shown with surefire®)
rLsr NEw rLs ™

reduction sleeve rLsM Mount for duty Belt
• Enables the RLS mounting system to • Provides a small mounting platform on duty belt to saf-d30 NEw
be used with lights of both .90" and .80" attach the RLS™ light
diameters • Designed for use with telescopic sights
• Will also accommodate any light, laser, or other
• Slides inside RLS mount to easily accept accessory that will fit on a Picatinny or light rail • Features two rings integral to the mounting base
narrower lights
• Fits belt widths up to 2.25" (58mm) • Single clamp is secured by two mil-spec thumb knobs to
maximize strength and rigidity
• Also fits on leg shroud or MLS 16
• Forward ring is cantilevered to allow scope to be positioned
• Included with RLS forward enough for proper eye relief

8112 standard chain style
• Top-quality, heavy-duty steel
construction
• 18-tooth, 3-retaining-bar system for
uncompromising security
• Positive swing-through action
• Built-in backloading for fast cuffing
• Reinforced steel swivels for added
strength and durability
RESTRAINTS
Based on a heritage of quality more
than two centuries old, Safariland • Available in Nickel and Black
now offers the finest, most durable
restraints available anywhere in the
world. Unique security features provide
an extra measure of confidence in a
comprehensive lineup of handcuffs and
other restraints.
8122 standard Hinge style

• Solid links connect the cuffs as
opposed to the roller chain
• Heavy-duty, solid hinges for
reinforced holding power
• Hinged models provide greater
subject control
• More comfortable feel in your hand
• Available in Nickel and Black
8112c colored chain style 8112-2 oversized chain style 8122-2 oversized Hinge style
• All the features of our standard handcuff with • 17% larger than the standard model • 17% larger than the standard model
added ability to color code subjects
• Ideal for restraining larger subjects • Ideal for restraining larger subjects
• Features a durable powder-coat finish
• 18-tooth, 3-retaining-bar system for uncompromising • Heavy-duty, solid hinges for reinforced holding power
• Can be used to classify threat levels, ages, security
agency, medical conditions and other factors • Hinged models provide greater subject control
• Available in Pink, Purple, Green, Blue, Red, • More comfortable feel in your hand
Yellow and Orange • Built-in backloading for fast cuffing
8220-3 double cuff ™
• The Double Cuff feature gives the officer

greater control and the ability to stabilize
the subject after one cuff is in place
• Two individual cuffs rather than the
standard single cuff for controlling both
wrists/forearms and ankles
• Standard length is 34" (86.36cm)
• ½" (1.27cm) wide with beveled edges to
reduce potential for subject injury
• Ample space for writing down subject
information
• Tensile strength of more than 400 lbs. (240kg)
• Two cuffs in one, which allows for
quicker subject control
• Available in White, Black, Red (training),
PaTENTEd Blue, Green, Orange, Pink, Purple, Yellow,
Lime Green and Tan
8220V double cuff ™

Variety Pack 8210-3 spare cuff ™
• A variety of colored Double Cuffs are • Standard single cuff for controlling both wrists/
also available in a set; can be used to forearms and ankles
help identify threat levels, ages, agency,
medical conditions and other factors as • 22" (55.88cm) when laid flat
required
• ½" (1.27cm) wide with beveled edges to reduce
potential for subject injury
• Tensile strength of more than 400 lbs. (240kg)
• Ample space for writing down subject information
• Available in Black and White

RESTRAINTS
8132 NEw rigid cuff
• Top quality, heavy-duty, steel
construction
• Added power and control that can
only come from a solid bar rigid
design
• 18 tooth, 3-retaining-bar system for
• Available in Nickel or Black
8121 NEw steloy Hinge style

• Top quality, heavy-duty, steel and
Steloy construction
• Steloy material makes the handcuff
40% lighter and 17% larger than
standard cuffs
• Solid links connect the cuffs as
opposed to the roller chain
• Heavy-duty, solid hinges for
reinforced holding power
• Hinged models provide greater
subject control
8111 NEw steloy chain style
• Top quality, heavy-duty, steel and
Steloy construction
• Steloy material makes the handcuff
40% lighter and 17% larger than
standard cuffs
uncompromising security HK-10 Handcuff Key
• Built-in backloading for fast cuffing • Stainless steel
• Reinforced steel swivels for added • Also available in dozen pack and gross pack
8400-1 NEw carbon fiber Handcuff Key

with Pocket clip
• Lightweight, oversized handcuff key

• Pocket clip for convenient carry
8142 NEw ultimate Hinge cuff • Textured grip allows solid grasp of key, even in wet
conditions
• Heavy-duty construction with
oversized rivet heads for added
strength
• 18 teeth – 3 retaining bars with
6 teeth on each bar makes cuffs
extremely difficult to pick
• Built-in backloading feature for
faster cuffing
• Leaf spring double locking system is
very difficult to defeat
• True Swing Technology ensures the
shackle hits the center of the cuff
every time
• Snaps open to a flat profile then
locks into position, becoming rigid
for use
• Folds for easy storage
• Lock and double lock like regular
handcuffs using a standard
handcuff key 8400-2 NEw carbon fiber Handcuff
Key with ring
• Lightweight, oversized handcuff key

• Key ring for convenient carry on belt key ring holder
or key chain
• Textured grip allows solid grasp of key, even in wet
conditions

RESTRAINTS
8500-0 cuff cutter 8500-1 safety cutter

• Can be used on any disposable restraint • Lever action for smooth cutting of disposable plastic
restraints
• Pocket-sized for easy carry and storage
• Simple, fast, one-squeeze operation
• Inexpensive
• Pocket-sized for easy carry
• Easy to use
• Safety design ensures blade cannot be used as
a weapon
• Easy left- or right-handed use
8710
safety cutter and 2 compact double cuff ™
restraints
• One squeeze removes nylon restraints simply and safely

• Convenient restraint cutting in a compact package
• Unique design ensures that it cannot be used as a weapon
against you; the Breakpoint guards against an attempt to
access the cutting blade to fashion a weapon
• Pocket-sized for easy transport and convenient storage
• Can be used to cut clothing or a vehicle seat belt
• Right- or left-hand operation
8711
safety cutter and 4 compact spare cuff ™ restraints
• Same features as above Model 8710
8220-0 compact double cuff ™
8210-0 compact spare cuff ™
8600 cuff-aide ™
• Compact version of Double Cuff • Compact version of Spare Cuff • Designed to be used in conjunction with handcuffs
to limit an individual’s ability to pick up contraband or
• User friendly and easy to carry and store • User friendly and easy to carry and store weapons while in custody
• Ideal backup to steel handcuffs; can • Ideal backup to steel handcuffs; can be carried in • Made from a tough nylon fiber
be carried in pocket, briefcase, glove pocket, briefcase, glove compartment, etc.
compartment, etc. • Belt clip to restrict arm movement while the detainee
• Available in Black and White is in a waist shackle
• Available in Black and White
8210-1 flex-cuf ®
8320 Tranzport Hood ™
8310 spit Net ™
• The Flex-Cuf was designed to be a quick, • Bacteria-filtering medical-grade fabric helps to contain • The Spit Net affixes under the arms for additional
temporary alternative to handcuffs contaminants and makes attempts at biting ineffective security while transporting threatening subjects
• Unique Strength Barb System contained • Secure-lock tab and elastic neckband allow for • Ideal for prisoner transport, it protects against
within the Flex-Cuf head makes it virtually convenient application and prevents self-removal of the spitting and biting
pick-proof hood, without limiting the individual’s range of vision
• Mesh netting and bacteria-filtering fabric give the
• Smooth inside surface, combined with subject full visibility and breathability while helping
rounded edges, designed to minimize the to restrict the spread of biological contaminants
chance of abrasion or tissue damage
• Nylon construction offers dimensional
stability as well as flexibility

6377
aLs® concealment Belt slide

simple straight up draw once all
releases are deactivated
• Injection-molded belt loop is user-
adjustable for cant and can be worn
crossdraw
• Slim and low profile design for
improved concealment
• Low-ride design for ease of draw
CONCEALMENT
HOLSTERS
• Available for 1.5" (38mm), 1.75"
(45mm), 2" (50mm) or 2.25" (58mm)
belt slots; please specify
• Available in STX finishes and Carbon
Fiber Look finish
BELT SLIDE
PaTENT PENdiNg 6379 NEw with Belt clip

detachment from belt
• Fits belt widths from 1.5"
(38mm) to 2.25" (58mm)
567 Belt slide

• 4 pistol and 4 revolver fits
accommodate over 100 different
weapons and are IDPA approved
• Adjustable injection-molded belt
loop fits 1.5" (38mm), 1.75" (45mm),
2" (50mm), and 2.25" (58mm); please
specify
• Belt loop is user-adjustable for cant
angle; can even be worn cross draw
• Genuine SafariLaminate™
PaTENTEd construction with suede lining to
help protect the gun’s finish
• Available in STX Plain Black and
Carbon Fiber Look finishes
569 NEw with Belt clip

(38mm) to 2.25" (58mm)
328 Pancake-style Belt Holster 528 open Top Pancake Belt slide Holster 529 NEw open Top concealment Belt slide
• Pancake-style holster • Specially designed for a federal law enforcement agency • Specially designed for federal law enforcement agency
• Can be adjusted to two different cant • Holster covers muzzle of gun, protecting your weapon • Dual snap belt loop for easy on/off access
positions and clothing
• Holster covers muzzle of gun, protecting your
• Thumb break/hammer strap and top draw • Low-profile body-hugging design weapon and clothing
design
• Features a molded detent that grips the trigger guard • Low-profile body-hugging design
• Fits belts up to 1.75" (45mm)
• Fits 1.75" (45mm) belt loop • Features a molded detent that grips the trigger guard
• Available in Plain Black finish
• Available in Plain Black finish • Fits 1.75" (45mm) belt loop
PaTENTEd &
PaTENT PENdiNg
747 Belt slide concealment Holster 748 NEw Thumbsnap concealment Belt slide 6367 aLs /sLs Belt slide
®
• Specially designed for a federal law • Specially designed for a federal law enforcement agency • ALS® (Automatic Locking System) secures weapon
enforcement agency once holstered; simple straight up draw once all
• Dual snap belt loop for easy on/off access releases are deactivated
• Extremely low profile, compact and body
hugging • Holster covers muzzle of gun to help protect weapon and • Includes SLS hood assembly and Hood Guard
clothing
• Thumb break/hammer strap and top draw • Optional Sentry available
design • Extremely low-profile, compact and body hugging design
• 7 hi-ride belt loop options offered, from 1.5" (38mm) to
• Fits belts up to 1.75" (45mm) • Top draw design with thumb break/hammer strap 2.25" (58mm), and two 1" drop model versions, from 1.5"
• Fits belts up to 1.75" (45mm) wide (38mm) to 2.25" (58mm)
• Available in Plain Black finish • Available in Plain Black and STX Tactical® finish

CONCEALMENT 5187
open Top concealment
Belt slide
• Compact and lightweight

construction
• Low cut sides for ease of draw and
HOLSTERS
added comfort
loop fits 1.5" (38mm), 1.75" (45mm),
2" (50mm), and 2.25" (58mm); please
specify
angle; can even be worn cross draw
• IDPA approved
weapons
• Available in STX finishes
PaTENTEd
5189 NEw with Belt clip
(38mm) to 2.25" (58mm)
0707
self-securing Belt slide Holster
• Easy to use, no snaps or straps

• Features a unique spring-loaded
self-securing frame jack. Simply
reholster weapon to automatically
lock it. Rock back to unlock and
draw
• Can also be worn in a cross draw
position
wraparound construction
• 7 high-ride belt loop options offered,
from 1.5" (38mm) to 2.25" (58mm),
and two 1" drop versions, from 1.5"
(38mm) to 2.25" (58mm)
• Available in STX Tactical® finish
0701 concealment Belt slide Holster

• Features a dual retention system consisting of the
trigger guard strap and an internal lock
• Mid-ride belt position and slight tilt forward for
comfortable wear and smooth draw
• Fits belt widths 1.5" (38mm), 1.75" (45mm) or 2.25" (58mm)
• Tough outer layer adds further protection
329
contour concealment Belt slide
• Originally designed to meet women’s fit

requirements, yet very comfortable for men
as well
• Low-cut front, no need to raise handgun
very high to clear holster
• Utilizes thumb break design
• Sturdy, flexible belt loop for added comfort
• Holster stays close to body when closed,
yet moves away when unsnapped for
ease of draw
• Fits belts up to 1.25" (32mm) wide
• Adjustable tension device
• Constructed of sturdy SafariLaminate™
527 open Top concealment Belt slide

• Low-profile, body-hugging design
• Features a molded detent that grips the trigger
guard
rides close to Easy to draw when
body when thumb unsnapped
snap is closed
PaTENTEd
6287 sLs concealment Belt slide Holster

• Concealment version of the SLS holster • Fits 1.5" (38mm), 1.75" (45mm), 2" (50mm)
and 2.25" (58mm) belt loops; please
• Features a unique rotating hood design specify
and semi-hi-ride position and slightly
forward cant • Adjustable tension device
• Rides close to the body, aiding in • Available in Plain Black and
concealment and weapon retention STX Tactical® finish

CONCEALMENT
6378
aLs concealment Paddle
®
& Belt slide combo

HOLSTERS
simple straight up draw once ALS is
deactivated by thumb while obtaining
shooting grip
• Injection-molded paddle design is
highly concealable and rides close
to body
• Injection-molded belt loop is user-
adjustable for cant angle and can be
worn crossdraw
loop fits 1.5" (38mm), 1.75" (45mm),
2" (50mm), and 2.25" (58mm); please
specify
• IDPA approved
• ALS retention in an open-top design
that is drawn with a natural thumb
only operation; no fingers in the
trigger guard area
construction with suede lining to help
PADDLE
PaTENT PENdiNg
protect the gun’s finish
Belt slide
included
PaTENTEd
5188
open Top concealment Belt slide
& Paddle combo
• Compact and lightweight

construction
• Low cut sides for ease of draw and
added comfort
• Injection-molded paddle designed for
enhanced concealability and comfort
loop fits 1.5" (38mm), 1.75" (45mm),
2" (50mm) and 2.25" (58mm); please
specify
angle; can even be worn crossdraw
• IDPA approved
weapons
Belt slide
PaTENTEd
included
0708
self-securing Paddle
• Easy to use; no snaps or straps

• Features a unique spring-loaded
self-securing frame jack.
Simply reholster weapon to
automatically lock; rock back to
unlock and draw
• Mid-ride belt position and slight
tilt forward for comfortable wear
and smooth draw
wraparound construction
• Fits pistols (only) up to
1.75" (45mm)
5181 open Top concealment Paddle

• Thermal-molded, self-locking paddle allows for
easy placement and removal of the holster
• Tension device allows for customizing holster
draw by adjusting resistance
• Genuine SafariLaminate™ construction with suede
lining to help protect the gun’s finish
• Available in Plain Black and STX Tactical® finish
568 custom fit Paddle & Belt

slide combo
• 4 pistol and 4 revolver fits

accommodate over 100
different weapons
• Injection-molded paddle
designed for concealability
and comfort
• Adjustable injection-molded
belt loop fits 1.5" (38mm), 1.75"
(45mm), 2" (50mm), and 2.25"
(58mm); please specify
• IDPA approved
construction with suede lining to
help protect the gun’s finish
• Available in STX Plain Black and
518 Thumb Break concealment

• Features medium- to hi-ride carry, wraparound
design and adjustable tensioning device to provide
Belt slide excellent weapon retention
included PaTENTEd • Suede-lined, custom-formed thumb break paddle
holster is lightweight and comfortable
• Available in Plain Black, Basket Weave and Carbon
Fiber Look finishes

CONCEALMENT
SHOULDER
1051
aLs® shoulder Holster

HOLSTERS
secures weapon once holstered
• SafariLaminate™ construction for
ease of draw and reholstering with
one hand
• Vertical or horizontal carry options
• Harness system (same as 1060) is
comfortable and fully adjustable
• Available in STX Plain Black finish
PaTENTEd & PaTENT PENdiNg
can Be worn Vertical or Back View

Horizontal
1061
Handcuff case (Not shown)
• Optional handcuff pouch for Back View
the Model 1060 Shoulder
Holster System
1060 Thumb Break 1090 gun Quick ™

shoulder Holster
• Unique harness system is comfortable and fully adjustable • Engineered for medium- and large-frame pistols
• Available with either magazine holder or speedloader pouch • Fits more than 90 pistol designs
• Optional Model 1061 Handcuff Pouch available • Ambidextrous shoulder holster
• Fits pistols and revolvers • Easy-to-adjust barrel length and width
• Available in Plain Black finish • Retention spring allows for easy one-handed reholstering
INSIDE WAIST
18
iwB Holster
• Open-top design
• Firm SafariLaminate™
construction allows holster
to stay open for ease of
reholstering
• Synthetic suede outer material
grips clothing for less movement
of holster
• Fits both 1.25" (32mm) and 1.5"
(38mm) belt widths
• Double-snap belt loop is
adjustable for cant angle
• Available in Black sueded finish
27 inside-the-Pants concealment Holster

• J-shaped belt hook can be worn with any belt
• Open-top SafariLaminate™ holster designed as an
undercover off-duty holster
• A polymer insert keeps the holster open for easy
weapon reholstering
POCKET AND ANKLE 25 inside-the-Pocket Holster

• Extra-thin, extra-soft holster for
extra-deep concealment
• Holster will stay open; simply drop handgun
into the pocket and it holsters itself
• Synthetic suede outer material grips
clothing for less movement of holster
• Firm, moisture-proof membrane layer
prevents perspiration from penetrating
the holster and collecting on the gun
• Available in Black sueded finish
4092
accessory sock
(Not shown)
• Replacement sock
liner for 4092 Ankle
Holster system
4092 ankle Holster

• Prevents concealed handgun from rotating
around and down the ankle
• Holster wraps around washable sock liner
• Uniquely designed lightweight system Low-Profile draw shown in Pocket
• Supported from the ground up by attaching
a small support strip to the shoe
• Right or left hand
• Available in Black

CONCEALMENT
BELT SLIDE
84
snapLok™
HOLSTERS
• Provides the speed of an open-top
holster with the security of Auto
Retention™, which retains weapon
upon holstering
• FingerLok™ retention mechanism
secures pistol by the trigger guard
upon inserting the weapon in the
holster; depress device to draw
• Belt loops snap on and off for easy
on/off convenience and may be
adjusted for snap opening in up or
down position
• Fits up to 1.5" (38mm) belt loops
• Available in full grain leather, Plain
Tan or Plain Black finish
PaTENTEd
82
carryLok™

upon holstering
• Features stay-open design for
efficient one-handed holstering
• 16-degree, forward carry
• Fits up to 1.75" (45mm) belt widths
PaTENTEd
4584
Evader™

upon holstering
secures pistol by the trigger guard upon
inserting the weapon in the holster;
depress device to draw
• Trilaminate construction features
rugged ballistic weave exterior, closed-
cell foam center and smooth nylon pack
cloth lining for a slick draw
• Reinforced open-top design stays open
for efficient one-handed reholstering
• Dual snap belt loop for easy
on/off access fits up to 1.75" (45mm)
belt widths
PaTENTEd
• Available in Black Ballistic
Weave finish
7 shadow ®
ii 5 Black widow ™
• Ultra hi-ride for excellent • Molded and pre-curved to fit the • Features ultra hi-ride carry and thumb • Open muzzle design allows various
concealability body for maximum comfort snap closure barrel lengths
• 3-slot design allows user to • Fits up to 1.75" (45mm) belt width • Compact profile for excellent • Fits up to 1.75" (45mm) belt width
vary the carry angle for his/her concealability
preference • Available in full grain leather, • Available in full grain leather, Plain Tan or
Plain Tan finish • Dual belt slots for superior stability Plain Black finish
• Strongside or cross draw carry,
open muzzle design

CONCEALMENT
77
Piranha™
HOLSTERS
• Unique, low cut front provides user

with a swift draw stroke
• 15-degree strongside cant
• 3-slot design allows custom
adjustment for user preference;
features both strongside and
cross draw carry
• Fits up to 1.75" (45mm) belt width
75
Venom™
• Slim profile and compact design in a

full-sized holster
• Rear belt slot pulls holster close to
body for excellent concealability
• Open muzzle design allows various
barrel lengths
• Contour molded for exact gun fit
PaTENTEd
7506 Thumbsnap Belt slide 105 Minimalist ™

with slots
• A feather-light belt slide design, • Adjust-A-Strap thumb break feature
™
• A compact, open-top design ideal for • Suede lining
molded and contoured to snug close permits adjustment for different daily wear
to body handguns • Fits belt widths up to 1.75" (45mm)
• Features elastic loop retainer tab for
• AccuMold trilaminate construction
®
• Dual snap web loops with firm-action secure retention • Available in full grain leather,
with Coptex™ lining for a smooth snaps provide convenient quick- Plain Tan finish
draw release on belts up to 1.75" (45mm) • Belt slide design provides excellent
wide stability for weapon
• Retention strap offers both thumb
break and front strap opening • Available in Black Ballistic Weave finish • Slots designed to pull firearm in close
to the hips for optimum concealment
55L Lightnin’ ®
• Designed specifically for hammerless

revolvers
• Finger-snap strap crosses behind trigger
guard for a middle finger release
• Fully suede lined
• Rides high and close to the body for
maximum comfort and concealability
• Available in full grain leather, Plain Tan finish

CONCEALMENT PADDLE
83
PaddleLok™
HOLSTERS

upon holstering
• Non-slip, contoured paddle features
molded elastomer ridges for
maximum grip on trousers or belt,
yet offers easy on/off convenience
• Paddle offers a variable range of
cant and height adjustability
• Fits up to 1.75" (45mm) belt widths
PaTENTEd
PaTENTEd
59 special agent ®
7500 accuMold ®
Paddle Thumbsnap
• Features our close-fit paddle design for comfort • Easy on/off convenience; exclusive, injection-molded
and concealability non-slip paddle; adjustable for various carry heights on
the waist/hip
• Exclusive, non-slip paddle features molded elastomer ridges
that retain paddle, yet it offers easy on/off convenience • Paddle design offers virtually limitless range
of cant, permitting both strongside and cross
• Paddle design offers virtually limitless range of cant, draw carry
permitting both strongside and cross draw carry
• AccuMold trilaminate construction with ballistic weave
• Adjustable for various carry heights on the waist/hip fabric, exterior high-density closed-cell foam center and
• Available in full grain leather, Plain Tan finish a Coptex™ lining for a smooth draw
• Available in Black Ballistic Weave finish
INSIDE WAIST
120
covert option™
• Dual belt loop straps for maximum

stability and firm placement on belt
• Slight forward cant for efficient
drawing while seated
• Reinforced top for instinctive
one-handed reholstering
• Low profile design effectively conceals
firearm with minimal bulk
• Belt wraps around suede center panel
to help retain firearm in holster
• High holster back protects clothing and
keeps edges of gun away from body
• Fits up to 1.75" (45mm) belts
• Available in full grain leather,
Plain Tan finish
3s Pistol Pocket ®
• Inside the waistband with dual snap attachment

to belt
• Fully adjustable swivel offers various carry options
• Open muzzle design
• Can be worn both strongside and cross draw
• 1.75" (45mm) belt loop
6 waistband Holster 6d aTB ™

waistband 100 Professional ™
• Worn inside the waistband • Inside waistband design provides comfort and concealability • Deep concealment design with high back to
comfortably shield torso against gun’s rough edges
• Soft suede construction • Thumb break design for those who prefer more security
• Features a non-slip suede-lined exterior next to body
• Ultra-thin profile provides optimum • Adjust-A-Break™ thumb break provides adjustability for a
concealment variety of gun models • Rides at optimum angle inside waistband to ensure
proper firing grip
• Hi-ride; strongside or cross draw • Ultra-thin and lightweight suede design for concealability
• Heavy-duty spring-steel belt clip securely anchors
• Heavy-duty spring-steel clip fits up to 1.75" • Hi-ride; strongside or cross draw holster to belt or trousers
(45mm) belts
• Heavy-duty 1.75" (45mm) clip keeps holster securely in place • Fits up to 1.75" (45mm) belts
• Available in Rust suede finish
• Available in Rust suede finish • Available in full grain leather, Plain Tan finish

CONCEALMENT SHOULDER
7700
LeatherLite™ system
• Offers the feel and appearance

of premium leather with the
advantages of lightweight synthetic
Duraskin™ finish
HOLSTERS
• Extremely lightweight for comfort;
no “printing” through outerwear for
ultimate concealability
• Unique offside design allows for
carry of optional open cuff case
• Magazine pouch hangs at 45-degree
The pivoting design of this angle for ease of magazine retrieval
harness allows it to move • Includes X-harness, double magazine
with the body. adjusts to fit pouch & two tie-down straps
male and female torsos up to
48" (122cm).
LeatherLite™ accessories
7700T Tie-down accessory 7700a double Magazine Pouch 7734 open cuff case
4620
ranger™ Tuxedo®
• Lightweight trilaminate
construction, offering padded
protection for the firearm
• 420-denier pack cloth exterior
for long wear and featherweight
comfort, with a soft suede-like
interior lining
• Comes complete with holster
X-harness, two tie-down straps
and double mag pouch or
speedloader panel
• Super-thin X-harness is one size
and fits up to a 48" chest
ranger™ Tuxedo® accessories
4620T Tie-down accessory 4620a double Magazine Pouch
X16
agent™
• Crafted from premium full grain cowhide, hand boned for

a precise fit
• Featherweight, slimline design for all day comfort
and concealability
• Comes with a choice of either contour-molded magazine
pouch or a low-profile speedloader panel, and X-style
pivoting harness that is flexible, strong and contours to
the torso
• Includes 2 suede leather tie-downs to secure holster
and offside pouch to belt
• Offered for both revolvers and semiautos
The X16 harness has a pivoting
design that moves with the body • Available in full grain leather, Plain Tan finish
and adjusts to fit male and female
torsos up to 48" (122cm).
agent™ accessories
X16T Tie-down accessory

X16a double Magazine Pouch
X16P offside accessory Panel
X16r speedloader Panel
The X15 harness adjusts to fit

male and female torsos up to an
optional 52" (128cm).
X15® shoulder Holster

• Dual spring closure provides firearm retention and stability
• Half lined with full grain leather for a smooth draw
• Detachable retainer strap
• Fully adjustable soft leather harness that adjusts to a 48" chest

CONCEALMENT VEST 4420 Tranzit Holster
• Unique nylon holster that
attaches to common body
armor vests with hook
& loop
• Design uses the holster as
a “side strap” for common
HOLSTERS
body armor
• Elastic webbing secures
weapon close to body
• Perfect for deep
concealment when a vest
is warranted or with a
backup weapon
• Additional pocket for
optional side plate
• Fits most compact pistols
and revolvers
4421
Tranzit ii Holster
• Unique nylon holster that attaches
to common body armor vests with
hook & loop
• Design uses the holster as a “side
strap” for common body armor
• Patent pending pull strap
allows quick access to the
weapon by pulling up on a small,
inconspicuous D-ring (as shown)
(shown closed, attached
• Elastic webbing secures weapon to hook & loop)
close to body
• Perfect for deep concealment
when a vest is warranted or with a
backup weapon
• Additional pocket for optional side
plate
• Fits most compact pistols and
revolvers
ANKLE
4750 ranger ™
Triad™
why the ankle?
The size of the calf in relation to the ankle provides a perfect location to
conceal a firearm and holster. It allows for greater flexibility in clothing 1
styles, as it is not dependent on a belt or waistband for support. Further,
ankles rarely receive the scrutiny of the casual observer.
ankle Pad
Our ankle pad for Model 4750 is adjustable for customized positioning, 2
and is breathable and washable.
3
1. Detachable Comfort Pad
2. Anklebone Locator Position
3. Arch Contour
compression strap
The Triad’s unique compression design allows

you to pull the gun butt tight into the calf for
unobtrusive carry.
150
Negotiator™ ankle Holster
• Neoprene leg strap expands to

fit comfortably around leg
• Lined with genuine sheepskin
for comfort and breathability
• 2" adjustable elastic leg strap
4750
secures and keeps holster in ranger™ Triad™
place
• Innovative tri-strap design offers
• Holster is canted for ease of adjustability to fit virtually any
draw ankle securely and comfortably
• Available in full grain leather, • Unique, contouring center
Plain Black finish compression strap allows user
to pull butt of gun snugly against
calf for a low profile and to keep
weapon secure
• Adjustable ankle pad can be
custom positioned for maximum
comfort over anklebone
• Elasticized retention strap with
easy pull tab for quick, easy
access to firearm
• Ankle pad cushion is removable
for easy cleaning and airing
• Available in Black Ballistic
Weave finish
150L
Negotiator ankle Holster
with 3" strap
4751
Triad Leg
™
• Same product features and Extender
benefits as 150 except with 3"
extended leg strap

573 Magazine Holder & Handcuff Pouch
• Unique paddle design features a self-locking belt hook
81 open Top single Magazine-snap • Adjustable tension device
• Features a low-cut design • Available in Plain Black finish
CONCEALMENT • Back side folds over to form snap-type belt loop
• For use on belts up to 1.75" (45mm)
BELTS & ACCESSORIES
079 open Top double Magazine Pouch – snap

• Low-cut design for easy magazine grasp
• For use on belts up to 1.75" (45mm) wide
cd-auTo auto Magazine Holder • Available in Plain Black, Basket Weave,
STX Tactical® or Carbon Fiber Look finishes
• Metal clip-on
• Carries single magazine in a butt-up, mid-ride position
• Ideal for plainclothes or off-duty use
123 Magazine Pouch – Horizontal
• Single magazine holder – carries magazines
in a horizontal position
• Hook & loop belt attachment wraps around belt
• Hook & loop flap keeps the magazine in the pouch
074 open Top single Magazine Pouch

• Paddle-style single magazine holder
• Features built-in locking mechanism that keeps the holder
in place at all times
• Fits belts up to 1.5" (38mm) wide 572 open Top double Magazine Pouch – Paddle
• Adjustable tension device • Low-cut design allows for quick access
• Available in Plain Black, STX Tactical® or Carbon Fiber • Unique paddle design features a self-locking belt hook
Look finishes
• Available in Plain Black, Basket Weave, STX Tactical®
or Carbon Fiber Look finishes
7352 Badge Holder 7350

• Shaped for shield-style
badges
Badge Holder
• Three sizes for star
71 NEw injection Molded single Mag Pouch 590 open Top Handcuff case-Paddle
and shield • Flexible “accordion” design allows for multiple fits and • Thermal-formed laminate handcuff holder
• Metal clip minimal size holds the handcuffs firmly and quietly in place
• 2.5" x 3.5" (64mm x 89mm) • Metal clip
• Fits magazines, flashlights, knives and multi-tools • Unique paddle design features a self-locking belt hook
• Diameter: 3" (76mm)
• Available in Black • Fits up to 1.75" (45mm) belt widths
• Fits up to 1.75" (45mm) belts • Available in Plain Black finish
B26/B27 Professional ™
Belt 1.5" (38mm)
& 1.25" (32mm)
45 Mag/cuff Paddle 25 angled carrycuff ™
Handcuff case • Premium full grain leather, oil tanned to a rich,
lustrous finish
• Paddle adjustable for carry height and angle • Angled at 45 degrees for quick access to cuffs
• Border stitched
• Provides easy one-handed draw for • Pull-through style for linked and hinged cuffs
handcuffs • Solid brass buckle
• Belt loop snaps on/off for user convenience; left and right
• Fits standard, oversized and hinged handcuffs hand versions for user’s draw preference • Complements Model 100 Professional™ holster
• Available in full grain leather, Plain Tan or • Fits up to 1.75" (45mm) belt loops • Plain Tan finish
Plain Black finishes
• Available in full grain leather, Plain Tan and Plain Black
finishes
20a open Top Magazine Pouch L820/L830 Plainclothes Belt 1.25" (32mm)
• Heavy-duty, spring-steel clip & 1.5" (38mm)
• Quick and compact • Made of SafariLaminate™ with a vegetable-tanned
• Fits belts up to 1.75" (45mm) leather support to accommodate holsters for larger
handguns
• Features a solid brass or chrome buckle
• Available in Plain Black or Carbon Fiber Look finishes
with solid brass or chrome buckle
990 wide offset Paddle

• The 990 provides additional clearance between the pistol’s
butt and user’s body
• Prevents hips from forcing butt of pistol into torso
• Provides greater wearing comfort 841/851 NEw contoured dress
Belt – Male 1.25" (32mm)
& 1.5" (38mm)
• Made of the long lasting and easy to
21 open Top Magazine Pouch care for SafariLaminate™ with a 7/8"
vegetable-tanned leather liner to provide
• Dual belt loop straps secure pouch to belt stability for handguns
• Can be angled for right or left hand carry • Curved to fit the contours of the body and features
• Designed for use with the Bianchi Model 120 two hidden cuff keys, back of waistband and one
holster behind the buckle, for easy accessibility
• Fits up to 1.75" (45mm) belts • Buckle is on left hand side, as with most traditional
male belts
• Available in Plain Black with solid brass or chrome buckle
580 speed strips ™

842/ NEw contoured dress Belt –
842/852
• Developed by John Bianchi over 50 years ago as a female 1.25" (32mm) & 1.5" (38mm)
compact loading device for revolvers • Made of the long-lasting and easy-to-care for
• Speed Strips™ fit in most single mag/knife pouches and SafariLaminate™ with a 7/8" vegetable tanned leather
liner to provide stability for handguns
24 carrycuff ™
Handcuff case
trouser or shirt pockets
• A perfect slim backup for speedloaders • Curved to fit the contours of the body and features
• Pull-through style for linked and hinged cuffs two hidden cuff keys, one at the back of waistband
• Injection molded from a flexible urethane material, they and one behind the buckle, for easy accessibility
• Belt loop snaps on/off for user convenience hold 6 rounds and load two at a time
• Buckle is on right-hand side for females
• Fits up to 1.75" (45mm) belt loops • Available for .38/.357 and .44/.45 caliber
• Available in Plain Black with solid brass or chrome buckle
• Available in full grain leather, Plain Tan and
Plain Black finishes

1L
Lawman™
• Western style, front strap closure;

fits single-action revolvers
• Hi-ride carry, open muzzle-design
• Full suede lining
• Fold over belt loop fits 1.75" (45mm)
to 2.25" (58mm) belts
Tan finish
SPORTING
HOLSTERS & BELTS
5BH/5BHL
Thumbsnap
• Features integral thumb snap

closure
• Strongside hi-ride carry; carries gun
close to body for added comfort
• 5BH (unlined); 5BHL (full suede
lining)
• 2"-3" holsters fit 1.75" (45mm) belt
slots
• 4" and larger holsters include 1.75"
(45mm) and 2.25" (58mm) belt slots
Tan finish
19/19L Thumbsnap 111 cyclone ™
• Wide belt loop provides stable carry close to the body; hi-ride for maximum • Thumb snap closure for secure fit and covered trigger guard design for both
comfort and concealability hunting and concealment applications
• Integral thumb snap enhances handgun retention • Fully suede lined
• 19 (unlined); 19L (full suede lining) • Unique belt loop design allows either strongside or cross draw carry
• 1.75" (45mm) belt loop • Quick release thumb snap
• Available in full grain leather, Plain Tan finish • Hi-ride carry, open muzzle design
• 1.75" (45mm) belt slot
PaTENTEd PaTENTEd
4100/4101 ranger ™
HusH™ system 7000 accuMold ®
sporting Holster 7001 accuMold ®
Thumbsnap
• Trilaminate construction featuring high- • Ideal for field, hunting and concealment carry • Suitable for both outdoor and concealment
density closed-cell foam for a memory applications, this holster rides at a 10- to 13-degree
fit and smooth nylon interior lining for a • Contour molded high-density trilaminate AccuMold ®
cant for a fast, instinctive draw
smooth draw construction for an exacting fit
• Thumb snap design incorporates the Bianchi®
• Cross-chest carry design; can also be worn • Hi-ride carry with closed muzzle and 10-degree forward Adjust-A-Strap™ feature to ensure a secure fit
on belts up to 2.25" (58mm) wide cant that aids in both comfort and presentation over the hammer
• Features a heavily padded load-bearing • Unique Coptex™ poly-knit lining for a smooth draw • Contour molded high-density trilaminate AccuMold®
harness for comfort • Sleek front strap closure incorporates Adjust-A-Strap™ construction for an exacting fit
• Unique Adjust-A-Strap™ thumb break feature to ensure a secure fit over the hammer • Coptex™ 100% polyknit inner lining for a smooth draw
closure for secure retention • 1.75" (45mm) injection-molded belt slot • 1.75" (45mm) injection-molded belt slot
• 4100 (Unscoped); 4101 (Scoped) • Available in Black Ballistic Weave finish • Available in Black Ballistic Weave finish
• Available in Black Ballistic Weave finish

SPORTING
CASES & BELTS
7201 Nylon Belt 1.75" (45mm)
• Four-part laminate for long-lasting shape and
4452 range Portfolio ™ • Firm polyethylene center strip sandwiched between a
high-density foam, with a ballistic weave outer and a
• Comfortably carries one or two firearms in its dual, thickly durable nylon lining
padded sleeves
• Roomy interior pocket for cleaning accessories, etc., and
elastic web loops for magazines or other equipment
• Constructed of ballistic weave nylon with Bianchi’s Air-
Flow™ lining – a breathable, moisture wicking fabric
• Conveniently zips open flat to use as a range pad
• Features outside carry strap for hearing protectors
B4 ranger Belt 1.75" (45mm)

• Full grain leather, unlined
• Popular Western billet design
• Solid brass buckle
• Plain Tan or Basket Tan finish
4451 deluxe Pistol case

• A slim, portfolio design featuring wraparound web carry B9 reversible fancy stitched Belt 1.75"
handles and an outside essentials pocket (45mm)
• Ballistic weave outer fabric with Bianchi’s Air-Flow ™ • Full grain leather with natural oil tan finish
lining – a breathable, moisture wicking fabric reverses to suede
• Thick, dense padding to cushion and protect firearm • Reversible, with fancy stitch design
• Conveniently opens flat to use as a shooting rest or pad • Solid brass buckle
B12 reversible sport stitched Belt 1.5" (38mm)

• Full grain leather with natural oil tan finish reverses
to suede
• Reversible, with fancy stitch design
• Solid brass buckle
4450 Pistol case B21 contour Belt 1.75" (45mm)

• Ballistic weave outer fabric with Bianchi’s Air-Flow™ lining
– a breathable, moisture wicking fabric • Fancy stitch design
• Thick, dense padding cushions and protects firearm • Solid brass buckle
• Outside zippered pocket for small essentials • Two thicknesses of heavy full grain leather
• Conveniently opens flat to use as a shooting rest or pad • Contoured to wrap smoothly around waist
• Fits most popular revolvers and pistols
COMPETITION
HOLSTERS, BELTS & ACCESSORIES
013 open class competition Holster

• Body machined out of aluminum to stabilize the • Able to adjust holster up and down, twist in or out,
handgun, yet offers little resistance for a secure and angle forward or back to custom fit your draw
fast draw
• Design incorporates a lock for your weapon. With
• Fits 1911’s, SVI’s, and CZ clones from 5" to 7.5" a simple push to the front, the lock secures your
(13cm -19cm) in length, with or without scopes handgun into the trigger block. A simple slide to the
rear and the trigger block is unlocked, allowing for a
• Patented injection-molded adjustable trigger guard lock fast and efficient draw while still retaining the gun in
• Front nosepiece designed to retain handgun and help the holster
prevent gun from being knocked out of the holster • Available in Black
while seated

COMPETITION
HOLSTERS, BELTS
& ACCESSORIES
5013
LEViTaTioN™ Holster
• Hollow tube design rolls away from

pressure to keep you comfortable
• Fully adjustable magazine pouches
for a custom fit
• Adjustable tension device for a
customized fit
• Aluminum base provides stable gun
position and drawing base
• Design incorporates lock for your
weapon; push forward, lock secure
handgun into trigger guard
• Adjustable muzzle guard
• Available in Black
002
cup challenge competition Holster
• Features dual-tension screws on the

holster body, one in back of cylinder
and the other in back of barrel,
allowing a balanced retention of the
handgun
• Hook & loop lined belt tab provides
a firm and adjustable carry when
used with Safariland 032 or 4350
Buckleless™ hook & loop lined
competition belts
• Accommodates both scoped and
non-scoped revolvers as well as
most revolvers with standard, heavy,
and slab side barrels
• Built-in removable muzzle strap
protects front sights
• Available in STX Tactical® or STX
Basket Weave finish
077BL replacement Belt Loop 083 Hook & Loop self-stick Kit (Not shown)
accessory (Not shown) • Ideal for fastening accessories to the belts
• Available for 1.5" (38mm), 1.75" (45mm), and 2.25" (58mm) belts
• Designed to work with Models 029, 032 and 4350
• Fits 771, 773, and 177
771 773
029 competition under Belt – Hook Lined
1.5" (38mm)
• Underbelt for Model 032
• Belt is worn in regular pant belt loops with
the hook exposed to mate with outer belt 5771 5773
• Available in Black with web finish
030 competition under Belt – Loop Lined

1.5" (38mm)
• Underbelt for 54327 Levitation™ System with
hook & loop
• Available in Black with web finish
771/5771 open Top Magazine Pouch 773/5773 open Top single Magazine Pouch
• Features two magazine tensioning screws on back side of • Utilizes the 90-degree adjustable belt loop
the holster to adjust tension on both the middle and end of
the magazine • 2 sets of tension screws threaded through rollers
for greater adjustment and lightning-fast reloads
• Sits against plastic rollers that reduce drag during draw
• Closed low-cut front to help secure magazine
032 NEw ELs competition Belt • Open-front design keeps index finger from touching the and prevent it from being knocked out of the front
holder during reload, ensuring fast reload of the pouch
• Reinforced to hold heavy competition
handguns and ammunition • 771 available in STX Tactical® or STX Basket Weave • Built-up channel for clearance of the bullet during
the draw
• Loop lined to hook to 029 underbelt • Order 5771 for Levitation™ System – STX Tactical finish only
• 773 in STX Tactical or STX Basket Weave
• Pre-cut holes to mount ELS 35 Receiver
Plates in multiple locations and angles • Order 5773 for Levitation™ System – STX Tactical finish
only
• Available in Black with Basket Weave and
coMP i speedloader
• Injection-molded construction
• Popular for concealment
54327 Levitation ™
Tube Belt 1.5" (38mm)
• Features a small knob providing
maximum concealment for small-
• Soft and flexible tubing increases comfort – less frame revolvers
than half the weight of conventional duty belts • Large-frame versions offer
• Must be worn with the 030, 99 or 992 loop maximum grip clearance 080-12 081-12
under belt
• Keepers are not needed 080-12 shotgun shell Holder
• Available in Nylok Pro finish
® 081-12 NEw shotgun shell Holder
coMP ii speedloader • Molded shotgun shell holder holds 2 12-gauge shells
• Belt clip features an extended bottom hook for security
• Injection-molded construction
• Fits belts up to 2.25" (58mm) wide
• Popular for duty use
• 081-12 features mounting holes
• Features a small knob providing
maximum concealment
for small-frame revolvers
• Medium-size knob for ease of
locking closed
• Large-frame versions offer
maximum grip clearance
4555 NEw shooters' range Bag

• Removable center carry compartment has
zippered, padded side panels for 4 separate
handgun compartments
• Removable and adjustable storage loops for
coMP iii speedloader
extra magazines • Injection-molded construction
• Full-wrap carry handles make it easy to move • Popular for competition
gear to different shooting stations
• Outer carry bag has dual zipper top for easy
• Spring-driven to offer the fastest
weapon reloading device J-KTr, J-LP shooters Loading Block
access and full coverage, flat side zipper pocket, • Convenient trays hold wadcutter, semi-wadcutter
ID window, and large outside zippered pocket for or round nosed .38 or .357 ammunition
towel, shooting glasses or hearing protection
• Popular for all speedloaders
• Overall dimensions: 14" x 9" x 10"

Team Safariland was started in 1985 and is an integral part of our product-development process. Team members have
combined competition and LE-trainer experience and regularly field-test materials and products for Safariland™. Their
involvement helps keep us at the very forefront of cutting-edge design.
TEAM SAFARILAND
1 2 3 4 5
1. KaNdi BLicK
Nra BiaNcHi cuP • NRA Certified Instructor
• Military/Law Enforcement/Civilian Firearms Instructor
A world-class event founded in 1979 by Bianchi International to establish • Female Gear Specialist for Safariland and Bianchi
• 2009: USPSA Nationals – Limited 10 – 5th Place Overall Ladies Division
practical pistol shooting as a professional sport. In 1984, the National Rifle • 2009: Bianchi Cup – Top 10 Finisher – 8th Place Overall Ladies
Association made the event its national championship of action shooting. • 2009: World Speed Shooting Steel Challenge – Top 10 Finisher in
Ladies Division
The 32nd annual event will be held at the Green Valley Rifle & Pistol Club in • 2009: Area Matches – Top 5 Finisher in Ladies Production & Single
Columbia, Missouri. Event dates are May 26-29, 2010. Stack Divisions
• 2009: SoCal Regional USPSA Events – Several Top Lady Finishes
for participation details, contact: 2. BiLL rogErs

Mr. Thomas Hughes • 1965-1991: Numerous state, national; and international shooting titles;
trap, IPSC, NRA-Bianchi, US Silver USPSA Team
National Manager, Pistol Programs • 1976-2009: Owner, operator, head instructor of the Rogers Shooting School
11250 waples Mill road, fairfax, Va 22030 • 1971: Inventor of the first all plastic holster, “Kydex”
• 1976-2008: Inventor of the first Level 1, 2, 3, 4 and 5 security holsters
Phone: 703-267-1451 • 1984-1991: Founding member, #008, vice president, Area 6 Director and
Board of directors for USPSA-IPSC
• 1987: Inventor of the first competition holster with internal locking
device, “Final Option"
3. scoTT carNaHaN
• 2009: NRA Bianchi Cup Open Expert Champion
• 2009: NRA Bianchi Cup Industry Team runner up
• 2009: Steel Challenge, Top 30 Open Division
• 2009: USPSA Nationals, top 25 overall L-10
• USPSA Master, NRA High Master
• 3-time USPSA National Class Champion
• VP of Marketing and Team Safariland
4. MicHaEL VoigT
• 2000-Present: USPSA President
• 2009: Superstition Mountain Mystery 3-Gun Open Champion
• 2009: NRA Bianchi Cup High Master Open Champion
• 2009: NRA Bianchi Cup Industry Team runner up
• 2009: USPSA Single Stack Nationals runner up
• 1999: IPSC World Champion
• 10-time USPSA Multi-Gun National Champion
5. roB LEaTHaM
• 23-Time USPSA National Champion
• 2009: NRA Bianchi Cup Metallic Champion
• 2009: NRA Bianchi Cup Metallic Shoot Off Champion
• 2009: NRA Bianchi Cup High Master Metallic Champion
• 2009: USPSA Single Stack Nationals Champion, 15th consecutive time
• 2009: World Speed Shooting Production Champion (Steel Challenge)
• 2009: USPSA Area-2 Limited Champion
• 8-Time NRA Bianchi Cup Champion
• 6-Time Steel Challenge Champion
6. doug KoENig
• 2009: NRA Bianchi Cup Open Shoot Off Champion
• 2009: Bianchi Cup Open class runner up
• 2009: NRA Bianchi Cup Industry team champion
• 2008: Masters International Champion – 15th time
• 2008: Bianchi Cup Champion – 11th time
• 3-time Steel Challenge Champion
• IPSC World Champion, 1990
7. MiKE LEHNEr
• Chief Instructor, Safariland Shooting School
• Member of IALEFI
• Certified LE Firearms Instructor for over 28 years
• NRA High Master
• CPPA Grand Master
• IDPA Master
• 3rd Place CDP, AZ IDPA Championships
7 9 8. KiPPi LEaTHaM
• 2009: USPSA Area-2 Production Champion
• 2009: USPSA Limited-10 Nationals – 3rd Place
• 2009: Western States Single Stack Ladies champion
• 2009: USPSA Single Stack Nationals ladies runner up
• 4-Time Member of “Gold Team USA” IPSC World Champions
9. JoHN PridE
• 2009: NRA Bianchi Cup Senior Champion
8 10 • 2009: NRA Bianchi Cup Industry team runner up
• 2009: NRA Bianchi Cup Senior Shoot Off Champion
• California’s Governor’s 20 Police Pistol Champion #1
• NRA Police President’s 20 #1
• 1-Time World NRA Action Pistol Champion
• 2-Time Australian National NRA Action Shooting Champion
• 4-Time NRA Bianchi Cup Champion
• 4-Time NRA Police National Champion
10. ToM caMPBELL

• 2001: USPSA Limited 10 National Champion
• 1977-1989: Member, USPSA Shooting Team
• 1986: USPSA Team Captain
• 1985: European Champion
• 1968 -1978: MA National Guard Pistol Team Member
• 1968-1990: Smith & Wesson Research and Development Team

Bianchi cowboy gear is available for purchase online. Visit bianchicowboy.com for more
product information on these fine western rigs.
Revisit the handcrafted glory of the Old West with

our line of cowboy gear and enjoy the quality of our
world-famous genuine leather holsters and belts. We
use only premium grade, full grain, vegetable-tanned
cowhide – the highest quality, most expensive leather.
Developed and used by the world-class shooters of
Team Bianchi, this is authentic cowboy gear that was
designed to perform both in and out of the arena.
Above all, it carries the legendary name Bianchi® and
was designed and produced in America.
BIANCHI COWBOY
HoNdo™
®
caLiforNia ouTLaw ™
cLEarwaTEr™
goLd MiNEr™
TEXas ouTLaw ™
Ts-6820
safariland Men’s Polo shirt
• Port Authority “Rapid Dry” Sport Shirt

quickly whisks away perspiration
• Black with the Safariland logo
embroidered on left chest
• Available in sizes S-2XL
ACCESSORIES
Ts-6810
safariland women’s Polo shirt
• Port Authority “Rapid Dry” Sport Shirt

quickly whisks away perspiration
• Double mercerized 2-ply 100% cotton
• Black V-neck with the Safariland logo
embroidered on left chest
• Available in sizes S-XL
Ts-2100/5500
safariland Mock Turtleneck
• Team Safariland Competition long-sleeve

T-shirt
• Made of 100% cotton fabric – Hanes® –
with spandex-enhanced cuffs and neck
• Silk-screened on front, back and sleeves
with Safariland logo
• Available in Black (2100), Tan (5500)
• Available in sizes S-XL
Ts-9250/9255
safariland Hat
• Adjustable size fits all

• Low-profile design
• Embroidered logo on front and
Safariland on back and on edge
of bill
• Black (9250), Tan (9255)
sPacEr KiTs
Spacer kits are available that position the holster away
from the body to accommodate various body styles.
Contact customer care for more information.
saf-cuP-2 coffee Tumbler 075-2 Hearing Protection Holder

• 16 oz. stainless tumbler with black matte • Available in Plain Black finish
finish
• Safariland logo printed in red and liquid
gold on one side
T-sPacEr-KiT
• For use with the 3-hole patterned holsters
• Positions holster farther from body for a smooth and
comfortable draw
• Designed to customize holster location to
accommodate various shapes
935 Bianchi ®
Mug
HardwarE KiT
• Kit provides the necessary materials: screws, rollers,
• Glossy black ceramic mug with metallic washers, T-nuts, hook and Allen wrench to service
gold logo Safariland holsters
• 12-oz. capacity
0702-PacK spacer Kit

• For use with concealment holsters
• Positions holster farther from body for a smooth and
comfortable draw
• Designed to customize holster location to
saf-cuP-Mug coffee Mug

• Black matte finish with Safariland logo in
dVd Training dVds
red and liquid gold on both sides • Wide selection of informative training DVDs available
• Ceramic
• 17 oz. capacity
Hda-KiT
• Designed to lower holster by 2" (50mm)
• Positions holster away from body to accommodate
various shapes
• Right and left hand specific
930 Bianchi ®
coasters cusToMiZEd-KiT (Not shown)
• Vegetable-tanned full-grain premium leather • For use with holsters and accessories
• Suede lined with border stitching • Positions holster farther from body for a smooth and
• Set of six in leather holder comfortable draw
• Embossed with Bianchi star logo • Designed to customize holster/accessory location to


coNsuMEr warNiNg: rEad iMMEdiaTELY
Safariland and Bianchi holsters and duty gear products are designed to meet the demand for high-performance
products for law enforcement and civilians. Fitted and used properly, a holster is a valuable aid in carrying a firearm.
Because holsters are used to carry firearms, however, any person purchasing or using a Safariland or Bianchi
holster should read and understand the following warning and all instructions included with his or her holster, as
well as be thoroughly familiar with the proper and safe use of his or her firearm in the circumstances in which he or
she is using it.
Close tolerances for holster/handgun fit require consistent handgun specifications and characteristics as well as
extremely precise holster design. Safariland produces its products in this manner of quality materials with efficiency
and safety in mind. Although these warnings may not pertain to all Safariland products, or all circumstances, they
should be read prior to the purchase, sale or use of any Safariland or Bianchi product. Some products have special
and/or supplemental instructions and/or safety information that must be read prior to their use. Call Safariland at
800.347.1200 for copies of these materials.
TraiNiNg aNd PracTicE

Use of a handgun under any circumstance may be dangerous. SERIOUS INJURY OR EVEN DEATH may result without
SAFETY, CARE & STORAGE
CONSUMER
proper training in the safe handling of firearms. Proper training should be obtained from an accredited firearms
safety program conducted by competent, qualified instructors in the military, police academies or National Rifle
Association-affiliated instruction programs. A firearm should not be carried or used without a thorough knowledge
of its characteristics and safe use in the circumstances in which it is intended to be used. It is also the user’s
responsibility to be certain that his or her firearm is in proper, safe operating condition.
We strongly recommend a regular holster practice regime be utilized to ensure the continued capabilities of both the
Safariland product and its user. Should you have any questions concerning your Safariland or Bianchi products, call
Safariland toll free at 800.347.1200.
ProPEr HoLsTEr fiT

NEVER PLACE A LOADED HANDGUN IN A HOLSTER WITHOUT FIRST TESTING FOR PROPER FIT WITH THE HANDGUN
UNLOADED. Although Safariland attempts to provide accurate information regarding which specific holster models
were designed to accommodate a specifically identified handgun, or handguns, Safariland does not warrant the
accuracy of such information and specifically disclaims any responsibility or liability for, or consequences resulting
from, errors or inaccuracies in such information. Users are advised not to rely on such compatibility information but
are advised to personally verify holster/handgun compatibility in each and every case using actual products.
Handgun manufacturers continually update manufacturing specifications in their quest for better products. These
changes may occur one or more times within a particular handgun model year, and make it difficult for proper
handgun identification and holster fit.
The slightest change in handgun design can have a major safety effect on the close tolerance of Safariland duty
gear products. These changes may not affect other holster brands that do not maintain the Safariland Duty Gear
high standards.
If the user has any questions or doubt concerning holster fit, contact Safariland immediately as to which version
of a particular handgun you and/or your customer may possess and its compatibility with Safariland or Bianchi
holsters.
Be advised that it is the user’s responsibility to periodically check his or her holster and related hardware for proper fit
and function. Should any product, including a Safariland or Bianchi Duty Gear product, become worn, loose, broken,
defective or ill-fitting, CEASE USE IMMEDIATELY.
oTHEr VErY iMPorTaNT warNiNgs

DO NOT use Safariland or Bianchi holsters with custom or modified guns or broken, worn or inferior manufactured
guns, including guns that are not of original factory specifications. DO NOT use after-market grips not manufactured
by Safariland, grip adapters, target hammers, target triggers or trigger shoes. After-market handgun modifications
may cause improper holster fit and ACCIDENTAL HANDGUN DISCHARGE. Never attempt to modify Safariland or
Bianchi duty gear products in any way.
Do not attempt to cock a handgun while holstered, as such cocking can cause severe damage to either the handgun
or holster, or both, and may cause an ACCIDENTAL DISCHARGE.
Some users of certain handgun models insist on carrying the weapon in what is referred to as a cocked and locked
condition (i.e., the gun is cocked with the safety engaged). Safariland does not recommend or approve of any such
practice, and advises against it. This condition for such handguns should be reserved only for the most advanced,
experienced and skilled professional shooters under conditions that require the handgun to be drawn and fired
under extremely short time constraints. Carrying a handgun in this condition INCREASES THE RISK OF ACCIDENTAL
DISCHARGE. It should only be used by those who have the training and experience to recognize the inherent risks
associated with it.
It should be noted that NO HOLSTER IS COMPLETELY SNATCH-PROOF OR TAKEAWAY-PROOF. Therefore, the user
must exercise extreme diligence at all times in any situation where another person may attempt to take the user’s
handgun. The handgun should be held in place by the user whenever vigorous activity, such as running, jumping,
falling or tumbling, is encountered or attempted. ALWAYS keep safety straps snapped if the holster is so equipped.
Keep thumb on back of hammer or slide when inserting handgun in holster to help ensure no movement occurs
during insertion. Always keep fingers clear of trigger when drawing or replacing handgun in holster. Place index
finger on outside of trigger guard to avoid inadvertent strap or foreign object interference when reholstering.
For complete ordering instructions and additional information, please visit safariland.com/dutygear.
To ENsure Your Satisfaction
Your product is carefully crafted from the finest materials. For product longevity and your own safety, here are some
commonsense guidelines:
Inspecting Your Product
1. Thoroughly read the safety information in this catalog and other information included with your purchase.
2. Make sure your handgun fits properly, safely and to your satisfaction.
3. Visually inspect your handgun for any defects in material or workmanship.
4. Check the retainer strap, spring or other retaining device and be certain that your handgun is properly and safely secured
for your application.
5. Visually inspect all stitchings, snaps, springs, clips and rivets for looseness, breakage or other damage.
6. Pay special attention to points of strain and critical points, such as belt loops, welts, retainer straps, springs or other
retaining devices.
7. Look for any sign that leather or other materials have become dry or brittle.
8. Should your holster or other product become worn, loose, defective or ill-fitting, cease use immediately.
Care and Storage

Leather
Storage
Store your leather product in a cool, dry place. High humidity can cause mildew, while dry heat and direct sunlight can cause
drying and cracking. If you leave your handgun in the holster or other product, check it daily for moisture, condensation or
corrosion. Changing atmospheric conditions, heavy perspiration and other factors could create such conditions.
Care
Treat the interior of your holster with spray silicone to help protect against excess moisture. Spray silicone also speeds the
draw by reducing friction.
If your product becomes water-soaked, reshape it as best you can and allow it to air-dry at room temperature. Do not use a
hot oven – it will shrink, harden and crack the leather.
Because Bianchi leather is hand finished with our special leather dressing, should your leather product become dry or
scratched, you can treat the exterior with a commercial leather dressing that does not contain lacquer. (Be careful when
using Neat’s foot oil; large amounts will soften the leather.)
Brass cartridges or other brass hardware when stored with leather will acquire a greenish residue called “verdigris.“ It is a
natural product of a chemical reaction between brass and vegetable-tanned leather, and it wipes off. (Using nickel-plated
cartridges in belt loops will avoid this condition.)
SafariLaminate™, AccuMold®, AccuMold® Elite™ and PatrolTek™

Storage
These products have been field-proven to withstand a wide variety of environmental conditions. These products should be
stored in a cool, dry environment when not in use. We do not recommend storing these products in a vehicle trunk or other
areas where extreme heat can exceed the outside environment.
Never store your SafariLaminate products near a heat source that emits high temperatures (200°F), which can deform or
destroy the polymer from which many SafariLaminate products are manufactured. If you have accidentally exposed your
equipment to a heat source you should immediately remove it from the area, allow it to cool to room temperature and then
operate it to ensure correct function.
Cleaning
INNOVATION NOT IMITATION.™ These products are best cleaned with a solution of warm, soapy water and a soft brush. A toothbrush and dish soap work
well. If decontamination is required, an antibacterial soap or 10% solution of household chlorine bleach may be used. After
cleaning, simply rinse off with fresh water and let air-dry. Be sure the product is completely dry inside and out prior to use.
You are holding in your hands a collection of the most time-honored, most When these products are exposed to salt spray or immersed in salt water, it is important to thoroughly rinse them in warm water as
universally praised duty gear anywhere in the world. For decades, the names soon as possible. Never use solvents such as acetone to clean AccuMold products, as this could result in damage to the product.
Safariland and Bianchi have been revered in law enforcement and security circles
like no other brand names. Now united under the Safariland banner, our duty gear
is the overwhelming choice of agencies around the world. And for good reason.
How to Measure Barrel Length
Before you order a holster, please be sure you have the correct barrel measurement for your handgun. This measurement is
As always, we work hard to build on the unique leadership position we have very easy to do, and it will ensure that you get the holster that’s exactly right for your gun.
earned, offering the industry’s most extensive range of top-quality holsters, belts,
accessories, restraints and more. We have combined our renowned legacies of 4" 5"
innovation, quality and customer care to provide genuine one-stop shopping for
every type of duty gear you will need. Today’s Safariland remains totally committed
to serving those who put it all on the line to uphold order and keep the peace.
And nobody does it better.
Semiautomatics – Measure
barrel length from the rear
Revolvers – Measure barrel length from portion of the ejection port to
the face of the cylinder to the muzzle. the muzzle.
WE ARE SAFARILAND
BODY ARMOR | DUTY GEAR | Less lethal | HARD ARMOR | PROTECTIVE GEAR
Armor Systems | FIREARMS ACCESSORIES | INVESTIGATION & EXAMINATION
safariland.com

DUTY GEAR CATALOG
3120 E. MISSION BLVD. • ONTARIO, California USA 91761

(909) 923-7300 • FAX (909) 923-7400 • (800) 347-1200 (USA ONLY)
safariland.com/dutygear • holsters.com • bianchi-intl.com • bianchicowboy.com
1209 ©2010 Safariland

2010 Safari Land DutyGear Catalog

Uploaded by

Copyright:

Available Formats

2010 Safari Land DutyGear Catalog

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

2010 Safari Land DutyGear Catalog

Uploaded by

Copyright:

Available Formats

What are some guidelines for inspecting duty gear?

What are some guidelines for inspecting duty gear?

How should leather duty gear be stored and cared for?

How should leather duty gear be stored and cared for?

WE ARE SAFARILAND

2010 DUTY GEAR PRODUCTS Catalog

3120 E. MISSION BLVD. • ONTARIO, California USA 91761

safariland.com/dutygear • holsters.com • bianchi-intl.com • bianchicowboy.com

1209 ©2010 Safariland

Care and Storage

SafariLaminate™, AccuMold®, AccuMold® Elite™ and PatrolTek™

TacTicaL & MiLiTarY

QuicK aTTacHMENT sYsTEMs

safariland rapid Light system ............................ 64

safariLaNd rEsTraiNTs .................... 66

a MEssagE froM our fouNdEr coNcEaLMENT BELTs & accEssoriEs

sTX Basket weave Nylok Pro

NYLoN LooK sTX BasKET wEaVE

sTX PLaiN BLacK

duTY TacTicaL Edw coNcEaLMENT

holsters.com • bianchi-intl.com • 800.347.1200 3

A state-of-the-art molded nylon holster constructed and

We’ve taken our patented AccuMold technology and

PatrolTek duty belts and accessories are made using our

BiaNcHi fiNisHEs BiaNcHi TEcHNoLogY

ErgoTek duty Belts

Duraskin™ Duraskin™ Duraskin™

dual Belt Loop Technology

QuicK aTTacHMENT sYsTEM – ELs

Edw duTY HoLsTErs

holsters.com • bianchi-intl.com • 800.347.1200 5

with Mid-ride uBL

• Level I Retention™ holster

To us, nothing is more important than officer

• Level I Retention™ holster

6312 ambidextrous Version

• Level I Retention™ holster

200 Top gun Level i

• Level I Retention™ holster

2005 with drop uBL

holsters.com • bianchi-intl.com • 800.347.1200 7

• Level II Retention™ holster

2955 with drop uBL

6280 Level ii Mid-ride with uBL

6285 Level ii with drop uBL

holsters.com • bianchi-intl.com • 800.347.1200 9

• Level III Retention™ holster

6275 with drop uBL

• Level III Retention™ holster

0705 with drop uBL

• Level III Retention™ holster

6365 with drop uBL

holsters.com • bianchi-intl.com • 800.347.1200 11

with Mid-ride uBL

• Level IV Retention™ holster

6075 with drop uBL

• Level V Retention™ holster with

6075 with drop uBL

0702-PacK spacer Kit T-sPacEr-KiT

holsters.com • bianchi-intl.com • 800.347.1200 13