Manual Alpha Ps
Manual Alpha Ps
Manual Alpha Ps
User’s manual
Manual do utilizador
ALPHA
750/1000/1200 PS
SAI in-line 750/1000/1200 VA
750/1000/1200 VA in-line UPS
UPS IN-LINE 750/1000/1200 VA
www.unitekpoweronline.com
TABLE OF CONTENT
1-1. Introduction
1-2. System Description
2-1. Installation
2-2. Operation
4. Caution
5. Trouble shooting
1. Overview
1-1 Introduction
The PS family of UPS (Uninterruptible Power Supply), is a line interactive device with
features conceived to provide an excellent protection to computers (PC), networks,
workstations and small capacity internet devices.
The PS family has an Automatic Voltage Regulator (AVR) that allows to operate in stable
conditions under varations of the main power, without the need to get into battery or
backed up mode. This features results in in extended battery life.
The family uses a RISC (Reduced Instruction Set Computer), that provides greater
operational flexibility: 1) “Delayed turn on”. During the turn on process the microprocessor
analizes the main power in order to ensure that it is in adequate conditions for the unit to
operate. 2) Green Power function. 3) “Overload Detection” and desactivation of the load if
the overload persists during a predetermined time. Additionally, the PS family has surge
protection, nosie filtering and fax/modem protection.
SPECIFICATIONS:
Front Panel
IEC
Output
Receptacles
Rear Panel
The following steps explain how to install the UPS to your PC.
Step 1. Assure AC power source output voltage is in the UPS
Requires voltage range specified on the rear panel.
Step 2. Plug the UPS power cord into a wall outlet or other
Power source.
Step 3. Plug the personal computer (PC) into the UPS output.
Step 4. Start the UPS by pressing the ON/OFF button for 4 seconds.
After the UPS turns on, it conducts a self-test and enters
Normal AC power mode. The AC power green LED indicator
illuminates indicating that power is available from the rear
receptacles.
Step 5. Shutdown the UPS by pressing ON/OFF button for 6 seconds
untill Red LED indicator illuminate.
2-2. OPERATION
Although your UPS has been designed and manufactured to assure personal safety,
improper use can result in electrical shock or fire. To assure safety, please observe the
following rules:
1. Turn off and unplug your UPS before cleaning. Do not use liquid or aerosol cleaner. A
dry cloth is recommended to dust from the surface of your UPS.
2. Do not install or operate your UPS in or near water
3. Do not place UPS on an unstable cart, stand or table
4. Do not place UPS under direct sunlight or close to heat emitting source
5. Do not place UPS power cord in any area where it may get damaged by heavy
objects.
6. Do not connect UPS to home appliance e.g. hairdryer, fan etc.
7. Do not connect UPS to Laser printer
8. If you store the UPS or UPS does not operate for a long period, recharge the battery
every month by starting the UPS for 8 hours.
9. Replace the battery with the same number and type of batteries as originally installed
in the UPS. The UPS must be unplugged from the AC power source before replacing
batteries (this operation require specialistic staff)
5. TROUBLE SHOOTING
CERTIFICATE OF GUARANTEE
Brand: UNITEK
Serie: ALPHA PS
Mode:
Fabrication number:
Client:
Invoice number:
Seller:
UNITEK POWER guarantees this product against any vice or manufacturing defect for a period of 36 months
starting from its date of sale. The guarantee will be valid in all the territory of the United Kingdom (other
countries according agreements with distributors) in the terms and conditions listed below
This guarantee doesn’t include transportation expenses originated by sending or return of this product. UNITEK
POWER will inform the sending/delivery point(s) of the product.
The claims due to defects on origin should be done within the 15 working days after delivery of the equipment.
2. UNITEK POWER will repair or replace the defective parts and will correct any electric or mechanical defect
of the equipment, directly or through a service partner at its own cost according to the conditions of this
guarantee.
3. The seller, distributor or sales channel is obliged to fulfil, date and stamp this Certificate of Guarantee in
order the end customer can use its right to ask for the guarantee service. The purchase invoice in original
and the present Certificate will be the valid documents to obtain the guarantee service.
4. There are excluded from this guarantee all damages caused by accidental facts like: transport,
manipulation, improper use or placement, hits, vandalism, fire, floods, atmospheric discharges, any type of
liquid spillages, battery acid spillages and any other circumstance derived from improper use or
maintenance.
5. There are excluded from this guarantee damages caused by negligence or bad use of this product, or any
different use of the indicated in the user manual. This guarantee doesn’t cover damages caused by
improper characteristics of the electric network, defective installation or adverse ambient.
6. UNITEK POWER can’t guarantee the good operation of this product if the required conditions indicated in
the technical specifications are not observed or damages caused by this reason. Likewise, it will not
covered by this guarantee neither services derived by non-fulfilment of valid laws and norms nor those
services required by lack of electric power, defective electrical installations of the building, disconnection of
the equipment from the electrical network or changes of placement not informed or approved by UNITEK
POWER technical department.
7. Parts and pieces prone to wear on consumables are not included in this guarantee.
8. This guarantee will be invalid if the product is opened or if it was tried to repair by not authorized personnel
of UNITEK POWER. Likewise the guarantee will be invalid if the serial numbers are altered. The
invalidation applies also if data like serial number date or invoice number of the present Certificate of
Guarantee is altered.
9. UNITEK POWER has the compromise to repair or replace the equipment described in this Certificate of
Guarantee in a time lapse no longer than 5 working days following to the reception of the equipment in the
workshop. This period could be prolonged by causes beyond control of UNITEK POWER.
IMPORTANTE NOTICE:
Please read this manual carefully before using his product Any malfunction resulting for
inadquate use of this product is not responsablity of the manufaturer or the Distributor.
The content of this manual is subjected to changes without prio notice.
1. Información General
1-1. Introducción
1-2. Descripción del Sistema
2. Instalación y Operación
2-1. Instalación
2-2. Operacion
5. Precaución
5. Solución de Fallas
1. Informacion General
1-1 Introducción
Front Panel
Puerto de comunicaciones
Entrada de AC
con fusible
Protección Modem /
Teléfono
IEC
Output
Receptacles
Vista Trasera
Paso 1. Asegurese que el tomacorriente de suministro eléctrico sea del voltaje requerido
(Vac) por la unidad y compatible con tipo Nema 5-15R / IEC
Paso 2: Conecte el UPS al tomacorriente.
Paso 3: Conecte el computador personal u otras cargas en las tomas de salida.
Paso 4. Encienda el UPS presionando el boton ON/OFF por 4-segundos
aproximadamente. El LED verde se ilumina indicando que la energía está disponible en
los receptáculos ubicados en la parte posterior de la unidad.
Paso 5. Apague el UPS presionando durante 6 segundos aproximadamente el botón
ON/OFF hasta que la luz roja se apague.
2-2. Operación
5. SOLUCION DE FALLAS
CERTIFICADO DE GARANTÍA
Marca: UNITEK
Serie: ALPHA PS
Modelo:
Número de fabricación:
Cliente:
Número de Factura:
Vendedor:
UNITEK POWER garantiza este producto contra todo vicio o defecto de fabricación por
el periodo de 36 meses contados desde la fecha de compra del mismo. La garantía será
válida para todo el territorio de España y Portugal (otros países según convenio con
distribuidor) en los términos y condiciones que se detallan a continuación:
Esta garantía no incluye gastos de transporte que se originen del envío y retorno de este
producto. UNITEK POWER notificará el/los punto(s) de recogida y entrega del producto.
Las reclamaciones por defectos de origen deben ser realizadas durante los 15 días
calendario siguientes a la fecha de compra del equipo.
CONDICIONES DE LA GARANTÍA.
5. Se excluye de esta garantía los daños causados por negligencia o mal uso del
producto o por uso diferente al indicado en el manual del producto. La garantía
no cubre daños causados por inadecuadas características de la red eléctrica de
alimentación, instalación deficiente o ambientes adversos.