Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.

de/en

Copper

Chemical Composition

Designation of
  Composition in % (mass fraction) Other elements
the material
Classifi Numeri
Europe
cation cal
an Max. Max. Max. Max. Max. Max. total excludi
of   Min. Cu Max. Bi Max. O Min. P Max. P Min. Be Min. Fe Max. Fe Max. Ni Min. Mn Min. Sn Min. Zn
Standa Be Co Mn Pb Sn Zn max. ng
symbol classifi
rd (EN)
s cation
CW004 EN
Cu-ETP 99.90 0.0005 0.04 - - - - - - - - - - 0.005 - - - - 0.03 Ag, O
A 1652
CW008 EN
Cu-OF 99.95 0.0005 - - - - - - - - - - - 0.005 - - - - 0.03 Ag
A 1652
CW020 EN
Cu-PHC 99.95 0.0005 -   0.001 0.006 - - - - - - - 0.0 - - - - 0.03 Ag, P
A 13599
CW024 EN
Cu-DHP 99.90 - - 0.015 0.04 - - - - - - - - - - - - - - -
A 1652
CW107 EN
CuFe2P Rest - - 0.015 0.15       2.1 2.6   - - C - - 0.05 0.20 0.2 -
C 1654
CW111 EN
CuNi2Si Rest - - - -       - 0.2   0.1 1.6 0.02 0.4 0.8 - - 0.3 -
C 1654
CW101 EN
CuBe2 Rest - - - - 1.8 2.1 0.3 - 0.2 0.3 - - - - - - - 0.5 -
C 1654

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Equivalents

  Approximate international equivalents

Numerical
Classification of symbols European Standard (EN) US (AISI) Japan (JIS) China (GB)
 classification
Cu-ETP CW004A EN 1652 C11000 C 1100
Cu-OF CW008A EN 1652      
Cu-PHC CW020A EN 13599      
Cu-DHP CW024A EN 1652      
CuFe2P CW107C EN 1654      
CuNi2Si CW111C EN 1654 C64700 -  
CuBe2 CW101C EN 1654      

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Mechanical properties

MECHANICAL PROPERTIES EN 1652

Tensile strength Rm Conventional Elongation

Designations yield strength at HV hardness
N/mm² A50mm for
0.2% Rp0.2 A for thicknesses
thicknesses up to
above 2.5 mm %
Material 2.5 mm
Metallurgical
min. max. N/mm² min. max.
Classification of Numerical condition
min. min.
symbols  classification
R200 200 250 (max. 100) - 42 - -
H040 - - - - - 40 65
               
R220 220 260 (max. 140) 33 42 - -
H040 - - - - - 40 65
               
R240 240 300 (max. 180) 8 15 - -
Cu-DHP CW024A
H065 - - - - - 65 95
               
R290 290 360 (max. 250) 4 6 - -
H090 - - - - - 90 110
               
R360 360 - (max. 320) 2 - - -
H110 - - - - - 110 -
NOTE 2- The numbers in brackets are not standard requirements, they are given for information purposes only.

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

MECHANICAL PROPERTIES EN 1654

Conventional yield
Tensile strength Rm Elongation Minimum bend radius according to bend edge
strength at 0.2% Rp 0.2
Designations HV hardness Perpendicular to the
Parallel to the direction
N/mm² N/mm² A50mm direction of rolling for
of rolling for thicknesses
thicknesses
% for % for
thicknesses thicknesses
up to 0.25 up to 0.25
Metallurgic from 0.1 above 0.25 over 0.25 over 0.25
Material min. max. min. max. min. max. mm mm
al condition mm to mm to 1.0 mm mm
inclusive inclusive
0.25 mm mm
inclusive inclusive
Symbolic Numerical           min. min.            
    R340 340 390 (240) - 8 10 - - - - - -
    H100 - - - - - - 100 120 0xt 0xt 0xt 0xt
                             
    R370 370 430 (330) - 4 6 - - - - - -
    H120 - - - - - - 120 140 0xt 1xt 0xt 1xt
CuFe2P CW107C                          
    R420 420 480 (380) - - 3 - - - - - -
    H130 - - - - - - 130 150 1xt 2xt 1xt 2xt
                             
    R470 470 - (440) - - - - - - - - -
    H140 - - - - - - 140 - - - - -
    R430 430 520 (330) - 10 13 - - - - - -
    H125 - - - - - - 125 155 0xt 1.5 x t 0xt 1xt
                             
    R450 450 600 (360) - 3 5 - - - - - -
    H130 - - - - - - 130 180 1.5 x t 2.5 x t 0xt 1.5 x t
CuNi2Si CW111C                          
    R510 510 600 (450) - 7 10 - - - - - -

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Conventional yield
Tensile strength Rm Elongation Minimum bend radius according to bend edge
strength at 0.2% Rp 0.2
Designations HV hardness Perpendicular to the
Parallel to the direction
N/mm² N/mm² A50mm direction of rolling for
of rolling for thicknesses
thicknesses
% for % for
thicknesses thicknesses
up to 0.25 up to 0.25
Metallurgic from 0.1 above 0.25 over 0.25 over 0.25
Material min. max. min. max. min. max. mm mm
al condition mm to mm to 1.0 mm mm
inclusive inclusive
0.25 mm mm
inclusive inclusive
Symbolic Numerical           min. min.            
    H150 - - - - - - 150 180 1.5 x t 2.5 x t 0xt 1.5 x t
                             
    R600 600 - (550) - 5 8 - - - - - -
    H180 - - - - - - 180 - 2xt - 0xt -
    R410 410 530 - - 35 35 - - - - - -
    H090 - - - - - - 90 150 0xt 0xt 0xt 0xt
    Y190 - - 190 (380) 35 35 - - - - - -
                             
    R1130 1130 1350 - - 3 3 - - - - - -
    H350 - - - - - - 350 410 - - - -
    Y960 - - 960 (1210) 3 3 - - - - - -
    B770 - - - - - - (350) (410) - - - -
                             
    R510 510 610 - - 15 15 - - - - - -
    H120 - - - - - - 120 190 1xt 1xt 0xt 0xt
    Y410 - - 410 (560) 15 15 - - - - - -
                             
    R1190 1190 1420 - - 3 3 - - - - - -
    H360 - - - - - - 360 430 - - - -
    Y1020 - - 1020 (1280) 3 3 - - - - - -
    B820 - - - - - - (360) (430) - - - -

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Conventional yield
Tensile strength Rm Elongation Minimum bend radius according to bend edge
strength at 0.2% Rp 0.2
Designations HV hardness Perpendicular to the
Parallel to the direction
N/mm² N/mm² A50mm direction of rolling for
of rolling for thicknesses
thicknesses
% for % for
thicknesses thicknesses
up to 0.25 up to 0.25
Metallurgic from 0.1 above 0.25 over 0.25 over 0.25
Material min. max. min. max. min. max. mm mm
al condition mm to mm to 1.0 mm mm
inclusive inclusive
0.25 mm mm
inclusive inclusive
Symbolic Numerical           min. min.            
                             
    R580 580 690 - - 8 8 - - - - - -
    H170 - - - - - - 170 220 2xt 2xt 1xt 1xt
    Y510 - - 510 (660) 8 8 - - - - - -
                             
    R1270 1270 1490 - - - - - - - - - -
    H370 - - - - - - 370 440 - - - -
    Y1100 - - 1100 (1350) - - - - - - - -
    B880 - - - - - - (370) (440) - - - -
                             
    R680 680 830 - - 2 2 - - - - - -
    H220 - - - - - - 220 290 3xt 3xt 1.5 x t 1.5 x t
    Y620 - - 620 (800) 2 2 - - - - - -
                             
    R1310 1310 1520 - - - - - - - - - -
CuBe2 CW101C H380 - - - - - - 380 450 - - - -
    Y1130 - - 1130 (1420) - - - - - - - -
    B920 - - - - - - (380) (450) - - - -
                             
    R690 690 760 - - 16 16 - - - - - -
    H210 - - - - - - 210 250 0.8 x t 0.8 x t 0.8 x t 0.8 x t

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Conventional yield
Tensile strength Rm Elongation Minimum bend radius according to bend edge
strength at 0.2% Rp 0.2
Designations HV hardness Perpendicular to the
Parallel to the direction
N/mm² N/mm² A50mm direction of rolling for
of rolling for thicknesses
thicknesses
% for % for
thicknesses thicknesses
up to 0.25 up to 0.25
Metallurgic from 0.1 above 0.25 over 0.25 over 0.25
Material min. max. min. max. min. max. mm mm
al condition mm to mm to 1.0 mm mm
inclusive inclusive
0.25 mm mm
inclusive inclusive
Symbolic Numerical           min. min.            
    Y480 - - 480 (660) 16 16 - - - - - -
    B400 - - - - - - (210) (250) 0.8 x t 0.8 x t 0.8 x t 0.8 x t
                             
    R750 750 830 - - 15 15 - - - - - -
    H230 - - - - - - 230 280 1xt 1xt 1xt 1xt
    Y550 - - 550 (760) 15 15 - - - - - -
    B500 - - - - - - (230) (280) 1xt 1xt 1xt 1xt
                             
    R820 820 930 - - 12 12 - - - - - -
    H250 - - - - - - 250 310 1.3 x t 1.3 x t 1.3 x t 1.3 x t
    Y650 - - 650 (870) 12 12 - - - - - -
    B530 - - - - - - (250) (310) 1.3 x t 1.3 x t 1.3 x t 1.3 x t
                             
    R930 930 1040 - - 9 9 - - - - - -
    H280 - - - - - - 280 350 2.5 x t 2.5 x t 2.5 x t 2.5 x t
    Y750 - - 750 (940) 9 9 - - - - - -
    B600 - - - - - - (280) (350) 2.5 x t 2.5 x t 2.5 x t 2.5 x t
                             
    R1060 1060 1250 - - 4 4 - - - - - -
    H310 - - - - - - 310 400 4xt 4xt 3xt 3xt
    Y930 - - 930 (1180) 4 4 - - - - - -

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Conventional yield
Tensile strength Rm Elongation Minimum bend radius according to bend edge
strength at 0.2% Rp 0.2
Designations HV hardness Perpendicular to the
Parallel to the direction
N/mm² N/mm² A50mm direction of rolling for
of rolling for thicknesses
thicknesses
% for % for
thicknesses thicknesses
up to 0.25 up to 0.25
Metallurgic from 0.1 above 0.25 over 0.25 over 0.25
Material min. max. min. max. min. max. mm mm
al condition mm to mm to 1.0 mm mm
inclusive inclusive
0.25 mm mm
inclusive inclusive
Symbolic Numerical           min. min.            
    B760 - - - - - - (310) (400) 4xt 4xt 3xt 3xt
                             
    R1200 1200 1320 - - 3 3 - - - - - -
    H360 - - - - - - 360 420 6xt 6xt 4xt 4xt
    Y1030 - - 1030 (1250) 3 3 - - - - - -
    B780 - - - - - - (360) (420) 6xt 6xt 4xt 4xt

NOTE 2- The numbers in brackets are not standard requirements, they are given for information purposes only.

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

MECHANICAL PROPERTIES EN 13599

a) Conventional yield strength

Nominal thickness t Tensile strength Rm Elongation
of 0.2% Rp 0.2
Designations HV hardness
A50mm for
mm N/mm² N/mm² A for
thicknesses
thicknesses
from 0.1 to
above 2.5
2.5 mm
Material Metallurgical up to & mm %
from min. max. min. max. min. max. inclusive %
condition including
Symbolic Numerical min. min.
    H040 0.10 5 40 65 - - - - - -
    R220 - - - - 220 260 - (140) 33 42
    H040 0.20 10 40 65 - - - - - -
    R200 - - - - 200 250 - (100) - 42
                         
    H065 0.10 10 65 95 - - - - - -
CW004A
Cu-ETP b) Cu-
CW008A R240 - - - - 240 300 180 - 8 15
OF Cu-PHC
CW020A
                         
    H090 0.10 10 90 110 - - - - - -
    R290 - - - - 290 360 250 - 4 6
                         
    H110 0.10 2 110 - - - - - - -
    R360 - - - - 360 - 320 - 2 -
NOTE 2- The numbers in brackets are not standard requirements, they are given for information purposes only.
a) For thicknesses below 0.10 mm the mechanical properties must be agreed between the customer and the supplier..
​b) For CU-ETP (CW004A) with thicknesses between 0.10mm and 0.20mm, both inclusive, the following values must be applied: Rm min. 200 N/mm2 and A50mm min 28%

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Finishes

BARE MATERIAL

The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier
when requesting the quote and in the order. Normally, a small residual layer of lubricant is left on cold-rolled products, which is
authorised unless otherwise specified.

ROUGHNESS EN 1654

This must be agreed between the customer and the supplier when requesting the quote and confirming the order.

SURFACE CONDITION EN 13599

The strips must be clean and free of detrimental defects, which must be specified by agreement between the customer and the supplier
in the request for quotes and in the order. Normally, a small residual layer of lubricant is left on cold-drawn products, and this is
acceptable unless otherwise specified. Discolouration is acceptable, provided that it is not detrimental to the use of the product . 

TIN COATINGS

Tin coatings for strips and copper strips and copper alloys: 

Type of coating Standard

Electrolytic EN 14436
Hot dip EN 13148

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

ELECTROLYTIC TINNING EN 14436

ELECTROLYTIC TIN PROCESS TYPES AND TYPES OF TIN COATINGS AND TIN ALLOYS EN 14436

Process Description
Process for matt electrolytic coatings. This is the standard finish of a traditional electrolytic bath.

Coatings with a bright appearance are obtained using baths that contain one or more
suitable brightening agents (brighteners). Their presence may not be desirable in
Process for bright electrolytic coatings.
subsequent melting or soft soldering processes. Furthermore, they may be beneficial for
frictional properties (low friction or sliding contacts).

Flow-brightened electrolytic coatings are obtained by heating a matt electrolytic coating

above its melting point for a few seconds and then cooling it. The coatings preserve their
Process for flow-brightened electrolytic coatings.
sheen after cooling. In practice, flow brightening is not used for coatings with thicknesses
above 5 μm (slip risk) or for coatings that are already bright.

NOTE - Tin electrolytic coatings may experience a spontaneous growth of metallic filaments (the combined effect of humidity and mechanical stresses, for example). This
phenomenon is highly undesirable for electrotechnical applications (risk of short circuit). The risk of this happening can be reduced by flow brightening, using tin-lead alloy
coatings or inserting a suitable sublayer.

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

TYPES OF STEEL ELECTROLYTIC COATINGS AND TIN ALLOYS ACCORDING TO APPLICABLE EN 14436

Coating thickness μm Types of coatings

min. max. Sn bright (Snb) Sn matt (Snm) Sn flow-brightened (Snf)
  1 As N/A As
0.8 1.2 As N/A *
1.5 2.5 B As B-R
2 4 B-C R B-R
3 6 B-C R N/A
5   B-C R-C N/A
NOTE 1: Applications:

N/A:  not applicable

B:      improves the suitability for soft soldering
*:       reduction of frictional forces
C:      corrosion resistance
R:      reduction of electrical resistance on a contact
As:    improved appearance

NOTE 2: These typical values are for information purposes and can be replaced by agreement between the customer and the supplier.

COMPOSITION OF THE TIN AND TIN ALLOYS EN 14436

Composition in % (mass fraction)

Type of coating Designation of the material
Min. Sn Others, total
Sn bright (Snb) Sn99 99 Remainder
Sn matt (Snm) or Sn flow-brightened (Snf) Sn99.50 99.5 Remainder

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

HOT DIP EN 13148

APPEARANCE EN 13148. HOT DIP TINNING

Thicknesses (average values) and preferred thickness ranges for coatings:

Thickness Thickness range

µm µm Application
average value from up to and included

Preventing surface oxidation, decorative

1.45 0.7 2.2
appearance, reducing frictional forces.

Preventing surface oxidation, decorative

2 1 3
appearance, reducing frictional forces.

3.5 2 5 Preventing corrosion

5 3 7 Extending the useful life
7.5 5 10 To aid soft soldering
10 7 13 To aid soft soldering

The appearance depends on the type of liquid film cooling, the type of coating and the technique used to remove excess molten metal.

The surface may have a bright or matt appearance, or a combination of both. The appearance of the coating does not affect its

suitability. If there are special requirements for the appearance of the coating, these requirements must be agreed at the time of the

quote and/or order.

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Tolerances

THICKNESS TOLERANCES EN 13599 / EN 1652

Nominal thickness Thickness tolerance for nominal widths according to EN 13599/  EN 1652
10 < and ≤ 200
> ≤ 200 < and ≤ 350 350 < and ≤ 700 700 < and ≤ 1000 1000 < and ≤ 1250
normal (Class A) special (Class B)
1) 2)
0.05 0.1 ± 10% - - - - -
0.1 0.2 ± 0.010 ± 0.007 ± 0.015 - - -
0.2 0.3 ± 0.015 ± 0.010 ± 0.020 ± 0.03 ± 0.04 -
0.3 0.4 ± 0.018 ± 0.012 ± 0.022 ± 0.04 ± 0.05 ± 0.07
0.4 0.5 ± 0.020 ± 0.015 ± 0.025 ± 0.05 ± 0.06 ± 0.08
0.5 0.8 ± 0.025 ± 0.018 ± 0.030 ± 0.06 ± 0.07 ± 0.09
0.8 1.2 ± 0.030 ± 0.022 ± 0.040 ± 0.07 ± 0.09 ± 0.10
1.2 1.8 ± 0.035 ± 0.028 ± 0.06 ± 0.08 ± 0.10 ± 0.11
1.8 2.5 ± 0.045 ± 0.035 ± 0.07 ± 0.09 ± 0.11 ± 0.13
2.5 3.2 ± 0.055 ± 0.040 ± 0.08 ± 0.10 ± 0.13 ± 0.17
3.2 4.0 - - ± 0.10 ± 0.12 ± 0.15 ± 0.20
4.0 5.0 - - ± 0.12 ± 0.14 ± 0.17 ± 0.23
5.0 6.0 - - ± 0.14 ± 0.16 ± 0.20 ± 0.26
Measurements in mm.
1) Including the value 0.05.
2) ± 10% of the nominal thickness

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

THICKNESS TOLERANCE FOR COATED MATERIAL

EN 13148. The thickness of the tinned strip must meet the required combination of tolerances for the thickness of the strip (table above)
and the range of thicknesses of the coatings ordered, for both sides.

EN 14436. The thickness of the strip prior to tinning must be in accordance with the approximate tolerances given in the table above. The
thickness tolerance of the tinned strip must take into account the minimum and maximum thicknesses of the coating.

WIDTH TOLERANCES OF THE STRIPS

Nominal Standard slitting tolerances Width tolerances for nominal widths according to
2)
thickness t for Metalle Schmidt  EN 13599/ EN 1654

over over over over over over

50 100 200 350 500 700
up to
and and and and and and
50- &
< ≤ 3-15 15-50 >150 up to up to up to up to up to up to
150 includi
100 200 350 500 700 1250
ng 50 0;+0,2
inclusi inclusi inclusi inclusi inclusi inclusi 0,05 0,1 - - - - - - - - - -
1)
ve ve ve ve ve ve

0;+0,1 0;+0,1 0;+0,1 0;+0,2

0,1 0,2 3) 3) 3) 0;+0,2 0;+0,3 0;+0,4 0;+0,6 0;+1,0 0;+1,5 0;+2,0
5 5 5 3)

0;+0,1 0;+0,1 0;+0,1

0,2 0,4 0;+0,2 0;+0,2 0;+0,3 0;+0,4 0;+0,6 0;+1,0 0;+1,5 0;+2,0
5 5 5
0;+0,1 0;+0,1 0;+0,2
0,4 1 0;+0,2 0;+0,2 0;+0,3 0;+0,4 0;+0,6 0;+1,0 0;+1,5 0;+2,0
7 8 4

1 1,5 0;+0,2 0;+0,2 0;+0,2 0;+0,3 0;+0,3 0;+0,4 0;+0,5 0;+1,0 0;+1,2 0;+1,5 0;+2,0
on
0;+0,2 0;+0,3
1,5 2 reques 0;+0,3 0;+0,3 0;+0,4 0;+0,5 0;+1,0 0;+1,2 0;+1,5 0;+2,0
6 2
t
on
0;+0,2 0;+0,3
2 2,5 reques 0;+0,3 0;+0,5 0;+0,6 0;+0,7 0;+1,2 0;+1,5 0;+2,0 0;+2,5
6 2
t
* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

Nominal Standard slitting tolerances Width tolerances for nominal widths according to
2)
thickness t for Metalle Schmidt  EN 13599/ EN 1654

over over over over over over

50 100 200 350 500 700
up to
and and and and and and
50- &
< ≤ 3-15 15-50 >150 up to up to up to up to up to up to
150 includi
100 200 350 500 700 1250 on on
ng 50 0;+0,3 0;+0,3
inclusi inclusi inclusi inclusi inclusi inclusi 2,5 3 reques reques 0;+1,0 0;+1,1 0;+1,2 0;+1,5 0;+2,0 0;+2,5 0;+3,0
2 5
ve ve ve ve ve ve t t

on on
0;+0,3 0;+0,3
3 5 reques reques 0;+2,0 0;+2,3 0;+2,5 0;+3,0 0;+4,0 0;+5,0 0;+6,0
2 5
t t

Measurements in mm.

1) Including the value t=0.05

2) Other, closer dimensional tolerances are possible under a commercial agreement .

3) Including the value t=0,1

LENGTH TOLERANCES 13599

Length tolerances of thick sheets, thin sheets and strips in cut lengths of up to 5000mm.

Length Nominal thickness Length tolerance

Without rolling (M) up to & including 25 ±50
5 and above 0; +10
Fixed length (F)
over 5 and up to 10 inclusive 0; +15
Measurements in mm.

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.
 Halskestraße, 26 | 40880 RATINGEN | DEUTSCHLAND https://metalprice.metalleschmidt.de/en

EDGE CAMBER TOLERANCES

Edge curve tolerances under commercial

Edge curve tolerances according to the EN 13599 Standard
agreement

Maximum deviation Maximum deviation

Nominal width (W)
1000 mm 1000 mm
Thickness (t) Thickness (t)

t ≤ 1.20 mm t > 1.20 mm t ≤ 0.5 mm 0.5 < t ≤ 1.20 mm 1.20 < t ≤ 2.50 mm 2.50 < t ≤ 3.20 mm 3.20 < t ≤ 5.00 mm

3≤W<6 2.50 4.00 - - - - -

6 < W ≤  10 2.00 3.00 - - - - -
1)
10 < W ≤  15 1.00 1.50 7.00 10.00 - - -
15 < W ≤  20 1.00 1.50 4.00 6.00 8.00 - -
20 < W ≤  30 0.50 1.00 4.00 6.00 8.00 - -

30 < W ≤  50 0.50 1.00 3.00 4.00 6.00 7.00

*under a commercial
50 < W ≤  350 0.50 1.00 2.00 3.00 4.00 5.00
agreement
350 < W ≤  1250 - - 2.00 3.00 4.00 5.00
Measurements in mm.
1) Including nominal width 10mm.

* The data contained in this catalogue are for information purposes only and are not under any circumstances, contractual supply conditions. Errors and omissions excepted.