Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

Littelfuse TVS Diode Array SP3304N Datasheet PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

TVS Diode Array (SPA® Diodes)

Lightning Surge Protection - SP3304N Series

SP3304N Series 3.3V 20A Diode Array RoHS Pb GREEN

Description

The SP3304N integrates 4 channels of low capacitance


diodes with an additional zener diode to protect sensitive
I/O pins against lightning induced surge events and ESD.
This robust device can safely absorb up to 20A per IEC
61000-4-5 2nd Edition (tP=8/20μs) without performance
degradation and a minimum ±30kV ESD per IEC 61000-4-2.
The low loading capacitance makes the SP3304N ideal for
protecting high-speed signal pins.

Features

Pinout • RoHS compliant, lead- • L


 ow capacitance of 3.5pF
free and halogen-free  (TYP) per I/O
1 3 5
• ESD, IEC 61000-4-2, • L
 ow leakage current of
±30kV contact, ±30kV air 1µA (MAX) at 3.3V
• E
 FT, IEC 61000-4-4, 40A • M
 oisture Sensitivity Level
GND (tP=5/50ns) (MSL Level-1)
• L
 ightning, IEC 61000-
4-5 2nd Edition, 20A
(tP=8/20µs)
9 7

Functional Block Diagram Applications

9 7 • 10/100/1000 Ethernet • Set Top Boxes


Interfaces • PBX Systems
5 • Customer Premise • Small Cells
Equipment (CPE)
• VoIP Phones

1 GND 3

Additional Information Application Example

*Package is shown as transparent Ethernet PHY


RJ-45 Connector
Tx+
J1
Datasheet Resources Samples
Tx-

SP3304N
PHY
Rx+
Life Support Note:
J8
Not Intended for Use in Life Support or Life Saving Applications
The products shown herein are not designed for use in life sustaining or life saving
applications unless otherwise expressly indicated. Rx-

© 2019 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/12/19
TVS Diode Array (SPA® Diodes)
Lightning Surge Protection - SP3304N Series

Absolute Maximum Ratings

Symbol Parameter Value Units

IPP Peak Current (tp=8/20μs) 20.0 A


PPK Peak Pulse Power (tp=8/20µs) 300 W
TOP Operating Temperature –40 to 125 ºC
TSTOR Storage Temperature –55 to 150 °C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in
the operational sections of this specification is not implied.

Electrical Characteristics (TOP=25ºC)

Parameter Symbol Test Conditions Min Typ Max Units

Reverse Standoff Voltage VRWM 3.3 V


Punch Through Voltage VPT IPT=5µA 3.5 V
Snap Back Voltage VSB ISB=50mA 2.8 V
Reverse Leakage Current ILEAK VR=3.3V, I/O to GND 0.5 1.0 µA
IPP=1A, tp=8/20µs, Fwd 6.0 V
IPP=5A, tp=8/20µs, Fwd 7.0 V
Clamp Voltage1 VC
IPP=10A, tp=8/20µs, Fwd 8.0 V
IPP=20A, tp=8/20µs, Fwd 11.5 V
Dynamic Resistance2 RDYN TLP, tP=100ns, I/O to GND 0.25 W
IEC61000-4-2 (Contact) ±30 kV
ESD Withstand Voltage1 VESD
IEC61000-4-2 (Air) ±30 kV
Diode Capacitance1 CI/O-GND Reverse Bias=0V, f=1MHz 3.5 5.0 pF
Diode Capacitance1 CI/O-I/O Reverse Bias=0V, f=1MHz 2.0 pF
Note: 1. Parameter is guaranteed by design and/or device characterization.
2.
Transmission Line Pulse (TLP) with 100ns width, 2ns rise time, and average window t1=70ns to t2=90ns

Pulse Waveform Clamping Voltage vs. IPP

110%
12.0
100%

90% 10.0

80%
8.0
Percent of IPP

70%
Clamp Voltage (VC)

60%
6.0
50%

40% 4.0

30%
2.0
20%

10%
0.0
0%
0.0 5.0 10.0 15.0 20.0 25.0 30.0 0 5 10 15 20
Time (μs)
Peak Pulse Current-IPP (A)

© 2019 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/12/19
TVS Diode Array (SPA® Diodes)
Lightning Surge Protection - SP3304N Series

Capacitance vs. Bias Ordering Information

5.0
Part Number Package Min. Order Qty.

SP3304NUTG µDFN-10 3000


4.0
Capacitance (pF)

3.0

2.0

1.0

0.0

0.0 0.5 1.0 1.5 2.0 2.5 3.0

Bias Voltage (V)

Soldering Parameters

Reflow Condition Pb – Free assembly tP


- Temperature Min (Ts(min)) 150°C TP Critical Zone
TL to TP
Pre Heat - Temperature Max (Ts(max)) 200°C Ramp-up
Temperature

TL
- Time (min to max) (ts) 60 – 180 secs tL
TS(max)
Average ramp up rate (Liquidus) Temp (TL) to peak 3°C/second max
Ramp-do
Ramp-down
TS(max) to TL - Ramp-up Rate 3°C/second max Preheat

- Temperature (TL) (Liquidus) 217°C TS(min)


Reflow tS
- Temperature (tL) 60 – 150 seconds
Peak Temperature (TP) 260+0/-5 °C 25
time to peak temperature
Time within 5°C of actual peak Temperature (tp) 20 – 40 seconds Time
Ramp-down Rate 6°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 260°C
Part Numbering System

SP 3304N U T G
G= Green
TVS Diode Arrays
(SPA® Diodes) T= Tape & Reel
Product Characteristics
Package
Lead Plating Pre-Plated Frame Series U= µDFN-10
Lead Material Copper Alloy
Substrate Material Silicon
Body Material Molded Epoxy
UL Recognized compound meeting Part Marking System
Flammability
flammability rating V-0

U* 4
Product Series Number of
U = SP3304N Channels
Assembly Site

© 2019 Littelfuse, Inc.


Specifications are subject to change without notice.
Revised: 09/12/19
TVS Diode Array (SPA® Diodes)
Lightning Surge Protection - SP3304N Series

Package Dimensions — µDFN-10


Package µDFN-10 (2.6x2.6mm)
Top View
JEDEC MO-229
D A Millimeters Inches
Symbol
Min Nom Max Min Nom Max
A 0.45 0.50 0.55 0.018 0.020 0.022
E A3 0.130 Ref 0.005 Ref
b 0.17 0.22 0.27 0.006 0.008 0.010
D 2.50 2.60 2.70 0.097 0.101 0.105
D2 2.10 2.15 2.20 0.081 0.083 0.085
E 2.50 2.60 2.70 0.097 0.101 0.105

B E2 1.21 1.26 1.31 0.046 0.049 0.051


e 0.50 BSC 0.020 BSC
L 0.35 0.40 0.45 0.014 0.016 0.018
Side View
0.10 C A3 Recommended Solder Pads µDFN-10L 2.6x2.6mm
A
Seating
Plane 0.05 C
C b
B

0.10 M C B A
Z G F C

Bottom View
Y

P X
D2 2X
C Dimension
Symbol Millimeters Inches
B 2.30 0.091
C 2.20 0.087
F 1.41 0.056
E2
G 1.65 0.065
P 0.50 0.020
X 0.37 0.015
Y 0.55 0.022
Z 2.75 0.108
e

Embossed Carrier Tape & Reel Specification — µDFN-10 (2.6x2.6mm)


P0 P2 D0 Symbol Millimeters
P1
A0 2.82 ± 0.05
E B0 2.82 ± 0.05
A0 5º MAX
D0 Ø1.50 + 0.10
F
T D1 Ø 0.50 + 0.05
W
E 1.75 ± 0.10
5º MAX F 3.50 ± 0.05
B0
D1 K0
K0 0.76 ± 0.05
P0 4.00 ± 0.10
P1 4.00 ± 0.10
Pin 1 Location P2 2.00 ± 0.05
T 0.25 ± 0.02
User Feeding Direction W 8.00 + 0.30 /- 0.10

Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are
not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at http://www.littelfuse.com/disclaimer-electronics.
© 2019 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 09/12/19

You might also like