Tank 88304-Report
Tank 88304-Report
DESIGN CALCULATION
Company Name:
Description:
Tag No. :
3D Design Tek Solution 4
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Warnings and Errors: Step: 0 5:27pm Sep 29,2018
Where:
Rm/20 = the lower of the tensile strengths at room temperature
Rp0,2/t = the 0,2% proof stress at design temperature
fd = the allowable stress
Austenitic Steel:
Where:
Rp1,0/t = the 1,0% proof stress at design temperature
Rm/t = the tensile stress at design temperature
Steel Description:
Name Number
0,2% Proof 1,0% Proof Tensile Elong. Impact Energy
Stress Stress Stress aft. Fract.% (ISO-V) kV
---------------------------------------------------------------------------
XXX 1.2345 200 240 480 35 40 60
YYY 1.7777 210 250 490 35 45 55
ZZZ 1.8888 305 315 580 35 40 65
---------------------------------------------------------------------------
In the above table, there are two values for the elongation. PV Elite uses
the equation for the larger elongation.
--------------------------------------------------------------------
--------------------------------------------------------------------
3D Design Tek Solution 8
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Input Echo: Step: 1 5:27pm Sep 29,2018
XY Coordinate Calculations:
| | | | | |
From | To | X (Horiz.)| Y (Vert.) | DX (Horiz.)| DY (Vert.) |
| | mm. | mm. | mm. | mm. |
----------------------------------------------------------------------
10 | 20| ... | 50 | ... | 50 |
20 | 30| ... | 2450 | ... | 2400 |
30 | 40| ... | 2500 | ... | 50 |
----------------------------------------------------------------------
Element Properties:
Calculation Results:
Thickness Due to Design Internal Pressure: e = max(es, ey, eb) - para 7.5.3.2
Required Crown Thickness due to Internal Pressure, see Figure 7.5-3 [es]:
= P * R/( 2 * f * z - 0.5 * P )
= 0.5 * 1200.0/( 2 * 1281.326 * 1.0 - 0.5 * 0.5 )
= 0.2342 mm.
Min. Des. Temp. per EN-13445 Part 2: Thickness 6.0 mm. at -29 °C :
Min. Des. Temp. per EN-13445 Part 2: Thickness 6.0 mm. at -29 °C :
= 1.1326
Thickness Due to Design Internal Pressure: e = max(es, ey, eb) - para 7.5.3.2
Required Crown Thickness due to Internal Pressure, see Figure 7.5-3 [es]:
= P * R/( 2 * f * z - 0.5 * P )
= 0.5 * 1200.0/( 2 * 1281.322 * 1.0 - 0.5 * 0.5 )
= 0.2342 mm.
Min. Des. Temp. per EN-13445 Part 2: Thickness 6.0 mm. at -29 °C :
= 6.031 bars
Weight of Details:
Note that the above value for the miscellaneous weight percent has
been applied to the shells/heads/flange/tubesheets/tubes etc. in the
weight calculations for metallic components.
Note:
The shipping total has been modified because some items have
been specified as being installed in the shop.
Weight Summary
3D Design Tek Solution 20
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Element and Detail Weights: Step: 5 5:27pm Sep 29,2018
| | Surface |
From| To | Area |
| | cm² |
----------------------------
10| 20| 16271.1 |
20| 30| 91684.3 |
30| 40| 16271.1 |
----------------------------
Total 124226.430 cm²
Note: ANSI Ratings are per ANSI/ASME B16.5 2013 Metric Edition
The Natural Frequencies for the vessel have been computed iteratively
by solving a system of matrices. These matrices describe the mass
and the stiffness of the vessel. This is the generalized eigenvalue/
eigenvector problem and is referenced in some mathematical texts.
Wind Load Calculations per India Std. IS-875 (Part-3) - 1987, Amd. 1&2 (2003):
Input Values:
Calculated Values:
From Height k1 k2 k3 Vz Cf
mm. m/sec
------------------------------------------------------------
10 15163.89 1.0000 1.0916 1.0000 48.51 0.7087
20 16482.53 1.0000 1.0990 1.0000 48.84 0.7087
30 17807.17 1.0000 1.1058 1.0000 49.14 0.7087
Nomenclature
Compute the maximum gust velocity using the gust response factor Gh [Vg]:
= Vw * Gh
= 115.687 * 1.0
= 115.687 Km/hr
Note:
The Wind Shears/Moments and the Earthquake Shears/Moments calculated
and printed in the Wind/Earthquake Shear and Bending report have
been factored by the input Scalar/Load reductions factors of;
Wind: 1.000; Earthquake: 1.000.
Note:
Review the Vessel Design Summary for the cumulative shear force
and bending moment on the support.
Wind Deflection:
| | | Hydrotest | | Hydrotest |
From| To | Tensile | Tensile | Compressive | Compressive |
| | N./mm² | N./mm² | N./mm² | N./mm² |
-------------------------------------------------------------------
10|Legs| 128.14 | 184.503 | -104.322 | -150.72 |
Legs| 20| 128.14 | 184.503 | -104.322 | -150.72 |
20| 30| 128.14 | 184.503 | -104.321 | -150.72 |
30| 40| 128.14 | 184.503 | -104.321 | -150.72 |
-------------------------------------------------------------------
| | Wght. Str. | Wght. Str. |Wght. Str. | Wght. Str. | Wght. Str. |
From| To | Empty | Operating |Hydrotest | Emp. Mom. | Opr. Mom. |
| | N./mm² | N./mm² | N./mm² | N./mm² | N./mm² |
---------------------------------------------------------------------------
10|Legs| ... | ... | ... | ... | ... |
Legs| 20| -0.38141 | -0.38141 | -0.38141 | 0.068267 | 0.068267 |
20| 30| -0.34957 | -0.34957 | -0.34957 | 0.068267 | 0.068267 |
30| 40| -0.049525 | -0.049525 | -0.049525 | ... | ... |
---------------------------------------------------------------------------
Longitudinal Stresses due to Weight Loads and Bending for these Conditions:
| | Wght. Str. | Bend. Str. |Bend. Str. | Bend. Str. | Bend. Str. |
From| To | Hyd. Mom. | Oper. Wind |Oper. Equ. | Hyd. Wind | Hyd. Equ. |
| | N./mm² | N./mm² | N./mm² | N./mm² | N./mm² |
---------------------------------------------------------------------------
10|Legs| ... | ... | ... | ... | ... |
Legs| 20| 0.068267 | 0.77161 | 0.024791 | 0.25463 | 0.0074372 |
20| 30| 0.068267 | 0.75422 | 0.024253 | 0.24889 | 0.0072759 |
30| 40| ... | 0.0064789 |0.00030863 | 0.002138 | 0.00009 |
---------------------------------------------------------------------------
General Notes:
-----------------------------------------------------------------------
10 152.598 42.107 194.705 0.782 0.216 0.997 0.000
10 153.510 42.255 194.703 0.786 0.216 0.997 0.000
20 46.022 42.265 87.245 0.236 0.216 0.447 0.000
30 152.651 41.628 194.271 0.782 0.213 0.995 0.000
Element From : 10 to : 20
Governing Load Case 9 : HP+HW+0.6WI
WRC 107 Stress Analysis for Leg to Shell Junction, Ope Condition
Note:
WRC Bulletin 537 provides equations for the dimensionless curves
found in bulletin 107. As noted in the foreword to bulletin 537,
"537 is equivalent to WRC 107". Where 107 is printed in the
results below, "537" can be interchanged with "107".
Note - The ! mark next to the figure name denotes curve value exceeded.
------------------------------------------------------------------------------------------------
Circ. Memb. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Bend. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. ML | 2.3| 2.3| -2.3| -2.3| 0.0| 0.0| 0.0| 0.0|
Circ. Bend. ML | 18.1| -18.1| -18.1| 18.1| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Circ. Str.| 20.4| -15.8| -20.4| 15.8| 0.0| 0.0| 0.0| 0.0|
------------------------------------------------------------------------------------------------
Long. Memb. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Bend. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Memb. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Bend. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Memb. ML | 0.3| 0.3| -0.3| -0.3| 0.0| 0.0| 0.0| 0.0|
Long. Bend. ML | 46.7| -46.7| -46.7| 46.7| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Long. Str.| 47.0| -46.4| -47.0| 46.4| 0.0| 0.0| 0.0| 0.0|
------------------------------------------------------------------------------------------------
Shear VC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear VL | 0.0| 0.0| 0.0| 0.0| -4.1| -4.1| 4.1| 4.1|
Shear MT | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Shear| 0.0| 0.0| 0.0| 0.0| -4.1| -4.1| 4.1| 4.1|
------------------------------------------------------------------------------------------------
Str. Int. | 47.0| 46.4| 47.0| 46.4| 8.3| 8.3| 8.3| 8.3|
Note - The ! mark next to the figure name denotes curve value exceeded.
Circ. Memb. |P 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Bend. |P 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. |MC 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. |MC 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. |ML 8.7| 8.7| -8.7| -8.7| 0.0| 0.0| 0.0| 0.0|
Circ. Bend. |ML 9.7| -9.7| -9.7| 9.7| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Circ. Str.| 18.4| -1.1| -18.4| 1.1| 0.0| 0.0| 0.0| 0.0|
------------------------------------------------------------------------------------------------
Long. Memb. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Bend. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Memb. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Bend. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Memb. ML | 3.7| 3.7| -3.7| -3.7| 0.0| 0.0| 0.0| 0.0|
Long. Bend. ML | 12.7| -12.7| -12.7| 12.7| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Long. Str.| 16.4| -9.0| -16.4| 9.0| 0.0| 0.0| 0.0| 0.0|
------------------------------------------------------------------------------------------------
Shear VC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear VL | 0.0| 0.0| 0.0| 0.0| -1.0| -1.0| 1.0| 1.0|
Shear MT | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Shear| 0.0| 0.0| 0.0| 0.0| -1.0| -1.0| 1.0| 1.0|
------------------------------------------------------------------------------------------------
Str. Int. | 18.4| 9.0| 18.4| 9.0| 1.9| 1.9| 1.9| 1.9|
| |
Tot. Long. Str.| 190.8| -190.0| -202.3| 198.6| -4.6| 2.8| -4.6| 2.8|
------------------------------------------------------------------------------------------------
Shear VC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear VL | 0.0| 0.0| 0.0| 0.0| -12.4| -12.4| 12.4| 12.4|
Shear MT | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Shear| 0.0| 0.0| 0.0| 0.0| -12.4| -12.4| 12.4| 12.4|
------------------------------------------------------------------------------------------------
Str. Int. | 190.8| 190.0| 202.3| 198.6| 24.8| 24.8| 24.8| 24.8|
------------------------------------------------------------------------------------------------
Circ. Q (SUS) | 18.1| -18.1| -18.1| 18.1| 0.0| 0.0| 0.0| 0.0|
Circ. Q (OCC) | 73.7| -73.7| -77.5| 77.5| -3.0| 3.0| -3.0| 3.0|
Circ. Q (TOTAL)| 91.8| -91.8| -95.6| 95.6| -3.0| 3.0| -3.0| 3.0|
------------------------------------------------------------------------------------------------
Long. Pm (SUS) | 1.1| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1|
Long. Pm (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Pm(TOTAL)| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1|
Long. Pl (SUS) | 0.3| 0.3| -0.3| -0.3| 0.0| 0.0| 0.0| 0.0|
Long. Pl (OCC) | 0.4| 0.4| -1.8| -1.8| -0.9| -0.9| -0.9| -0.9|
Long. Pl(TOTAL)| 0.7| 0.7| -2.1| -2.1| -0.9| -0.9| -0.9| -0.9|
Long. Q (SUS) | 46.7| -46.7| -46.7| 46.7| 0.0| 0.0| 0.0| 0.0|
Long. Q (OCC) | 190.4| -190.4| -200.4| 200.4| -3.7| 3.7| -3.7| 3.7|
Long. Q (TOTAL)| 237.1| -237.1| -247.1| 247.1| -3.7| 3.7| -3.7| 3.7|
------------------------------------------------------------------------------------------------
Shear Pm (SUS) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pm (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pm(TOTAL)| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pl (SUS) | 0.0| 0.0| 0.0| 0.0| -4.1| -4.1| 4.1| 4.1|
Shear Pl (OCC) | 0.0| 0.0| 0.0| 0.0| -12.4| -12.4| 12.4| 12.4|
Shear Pl(TOTAL)| 0.0| 0.0| 0.0| 0.0| -16.5| -16.5| 16.5| 16.5|
Shear Q (SUS) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Q (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Q (TOTAL)| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Pm (SUS) | 2.1| 2.2| 2.1| 2.2| 2.1| 2.2| 2.1| 2.2|
------------------------------------------------------------------------------------------------
Pm (SUS+OCC) | 2.1| 2.2| 2.1| 2.2| 2.1| 2.2| 2.1| 2.2|
------------------------------------------------------------------------------------------------
Pm+Pl (SUS) | 4.4| 4.5| 1.0| 0.9| 8.3| 8.3| 8.3| 8.3|
------------------------------------------------------------------------------------------------
Pm+Pl (SUS+OCC)| 13.1| 13.1| 10.9| 10.9| 33.1| 33.1| 33.1| 33.1|
------------------------------------------------------------------------------------------------
Pm+Pl+Q (Total)| 238.8| 235.4| 248.2| 246.1| 33.1| 33.1| 33.1| 33.1|
------------------------------------------------------------------------------------------------
Circ. Q (OCC) | 36.5| -36.5| -45.1| 45.1| -11.7| 11.7| -11.7| 11.7|
Circ. Q (TOTAL)| 46.2| -46.2| -54.8| 54.8| -11.7| 11.7| -11.7| 11.7|
------------------------------------------------------------------------------------------------
Long. Pm (SUS) | 2.5| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5|
Long. Pm (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Pm(TOTAL)| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5|
Long. Pl (SUS) | 3.7| 3.7| -3.7| -3.7| 0.0| 0.0| 0.0| 0.0|
Long. Pl (OCC) | 13.6| 13.6| -17.6| -17.6| -3.6| -3.6| -3.6| -3.6|
Long. Pl(TOTAL)| 17.4| 17.4| -21.3| -21.3| -3.6| -3.6| -3.6| -3.6|
Long. Q (SUS) | 12.7| -12.7| -12.7| 12.7| 0.0| 0.0| 0.0| 0.0|
Long. Q (OCC) | 43.9| -43.9| -62.4| 62.4| -6.4| 6.4| -6.4| 6.4|
Long. Q (TOTAL)| 56.6| -56.6| -75.1| 75.1| -6.4| 6.4| -6.4| 6.4|
------------------------------------------------------------------------------------------------
Shear Pm (SUS) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pm (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pm(TOTAL)| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pl (SUS) | 0.0| 0.0| 0.0| 0.0| -1.0| -1.0| 1.0| 1.0|
Shear Pl (OCC) | 0.0| 0.0| 0.0| 0.0| -2.9| -2.9| 2.9| 2.9|
Shear Pl(TOTAL)| 0.0| 0.0| 0.0| 0.0| -3.9| -3.9| 3.9| 3.9|
Shear Q (SUS) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Q (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Q (TOTAL)| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Pm (SUS) | 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0|
------------------------------------------------------------------------------------------------
Pm (SUS+OCC) | 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0|
------------------------------------------------------------------------------------------------
Pm+Pl (SUS) | 13.7| 13.7| 3.7| 3.7| 5.3| 5.3| 5.3| 5.3|
------------------------------------------------------------------------------------------------
Pm+Pl (SUS+OCC)| 46.4| 46.4| 43.7| 43.6| 8.8| 8.8| 8.8| 8.8|
------------------------------------------------------------------------------------------------
Pm+Pl+Q (Total)| 92.6| 37.0| 98.5| 56.3| 12.1| 16.1| 12.1| 16.1|
WRC 107 Stress Analysis for Leg to Shell Junction, Test Condition
Note:
WRC Bulletin 537 provides equations for the dimensionless curves
found in bulletin 107. As noted in the foreword to bulletin 537,
"537 is equivalent to WRC 107". Where 107 is printed in the
results below, "537" can be interchanged with "107".
Note - The ! mark next to the figure name denotes curve value exceeded.
------------------------------------------------------------------------------------------------
Circ. Memb. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Bend. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. ML | 10.1| 10.1| -10.1| -10.1| 0.0| 0.0| 0.0| 0.0|
Circ. Bend. ML | 78.8| -78.8| -78.8| 78.8| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Circ. Str.| 88.9| -68.7| -88.9| 68.7| 0.0| 0.0| 0.0| 0.0|
------------------------------------------------------------------------------------------------
Long. Memb. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Bend. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Memb. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Bend. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Memb. ML | 1.1| 1.1| -1.1| -1.1| 0.0| 0.0| 0.0| 0.0|
Long. Bend. ML | 203.7| -203.7| -203.7| 203.7| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Long. Str.| 204.9| -202.6| -204.9| 202.6| 0.0| 0.0| 0.0| 0.0|
------------------------------------------------------------------------------------------------
Shear VC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear VL | 0.0| 0.0| 0.0| 0.0| -18.0| -18.0| 18.0| 18.0|
Shear MT | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Shear| 0.0| 0.0| 0.0| 0.0| -18.0| -18.0| 18.0| 18.0|
------------------------------------------------------------------------------------------------
Str. Int. | 204.9| 202.6| 204.9| 202.6| 36.0| 36.0| 36.0| 36.0|
Note - The ! mark next to the figure name denotes curve value exceeded.
Circ. Memb. |P 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Bend. |P 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. |MC 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. |MC 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Circ. Memb. |ML 37.9| 37.9| -37.9| -37.9| 0.0| 0.0| 0.0| 0.0|
Circ. Bend. |ML 42.5| -42.5| -42.5| 42.5| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Circ. Str.| 80.4| -4.6| -80.4| 4.6| 0.0| 0.0| 0.0| 0.0|
------------------------------------------------------------------------------------------------
Long. Memb. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Bend. P | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Memb. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Bend. MC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Memb. ML | 16.3| 16.3| -16.3| -16.3| 0.0| 0.0| 0.0| 0.0|
Long. Bend. ML | 55.4| -55.4| -55.4| 55.4| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Long. Str.| 71.7| -39.1| -71.7| 39.1| 0.0| 0.0| 0.0| 0.0|
------------------------------------------------------------------------------------------------
Shear VC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear VL | 0.0| 0.0| 0.0| 0.0| -4.2| -4.2| 4.2| 4.2|
Shear MT | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Shear| 0.0| 0.0| 0.0| 0.0| -4.2| -4.2| 4.2| 4.2|
------------------------------------------------------------------------------------------------
Str. Int. | 80.4| 39.1| 80.4| 39.1| 8.4| 8.4| 8.4| 8.4|
| |
Tot. Long. Str.| 157.6| -156.3| -161.4| 159.1| -1.5| 0.9| -1.5| 0.9|
------------------------------------------------------------------------------------------------
Shear VC | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear VL | 0.0| 0.0| 0.0| 0.0| -12.4| -12.4| 12.4| 12.4|
Shear MT | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
| |
Tot. Shear| 0.0| 0.0| 0.0| 0.0| -12.4| -12.4| 12.4| 12.4|
------------------------------------------------------------------------------------------------
Str. Int. | 157.6| 156.3| 161.4| 159.1| 24.8| 24.8| 24.8| 24.8|
------------------------------------------------------------------------------------------------
Circ. Q (SUS) | 78.8| -78.8| -78.8| 78.8| 0.0| 0.0| 0.0| 0.0|
Circ. Q (OCC) | 60.7| -60.7| -62.0| 62.0| -1.0| 1.0| -1.0| 1.0|
Circ. Q (TOTAL)| 139.6| -139.6| -140.8| 140.8| -1.0| 1.0| -1.0| 1.0|
------------------------------------------------------------------------------------------------
Long. Pm (SUS) | 1.1| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1|
Long. Pm (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Pm(TOTAL)| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1| 1.1|
Long. Pl (SUS) | 1.1| 1.1| -1.1| -1.1| 0.0| 0.0| 0.0| 0.0|
Long. Pl (OCC) | 0.7| 0.7| -1.1| -1.1| -0.3| -0.3| -0.3| -0.3|
Long. Pl(TOTAL)| 1.8| 1.8| -2.3| -2.3| -0.3| -0.3| -0.3| -0.3|
Long. Q (SUS) | 203.7| -203.7| -203.7| 203.7| 0.0| 0.0| 0.0| 0.0|
Long. Q (OCC) | 157.0| -157.0| -160.3| 160.3| -1.2| 1.2| -1.2| 1.2|
Long. Q (TOTAL)| 360.7| -360.7| -364.0| 364.0| -1.2| 1.2| -1.2| 1.2|
------------------------------------------------------------------------------------------------
Shear Pm (SUS) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pm (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pm(TOTAL)| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pl (SUS) | 0.0| 0.0| 0.0| 0.0| -18.0| -18.0| 18.0| 18.0|
Shear Pl (OCC) | 0.0| 0.0| 0.0| 0.0| -12.4| -12.4| 12.4| 12.4|
Shear Pl(TOTAL)| 0.0| 0.0| 0.0| 0.0| -30.4| -30.4| 30.4| 30.4|
Shear Q (SUS) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Q (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Q (TOTAL)| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Pm (SUS) | 2.1| 2.2| 2.1| 2.2| 2.1| 2.2| 2.1| 2.2|
------------------------------------------------------------------------------------------------
Pm (SUS+OCC) | 2.1| 2.2| 2.1| 2.2| 2.1| 2.2| 2.1| 2.2|
------------------------------------------------------------------------------------------------
Pm+Pl (SUS) | 12.2| 12.3| 8.0| 7.9| 36.0| 36.0| 36.0| 36.0|
------------------------------------------------------------------------------------------------
Pm+Pl (SUS+OCC)| 19.7| 19.8| 16.2| 16.1| 60.8| 60.8| 60.8| 60.8|
------------------------------------------------------------------------------------------------
Pm+Pl+Q (Total)| 363.5| 357.8| 365.2| 362.8| 60.8| 60.8| 60.8| 60.8|
------------------------------------------------------------------------------------------------
Circ. Q (OCC) | 31.7| -31.7| -34.5| 34.5| -3.9| 3.9| -3.9| 3.9|
Circ. Q (TOTAL)| 74.2| -74.2| -77.0| 77.0| -3.9| 3.9| -3.9| 3.9|
------------------------------------------------------------------------------------------------
Long. Pm (SUS) | 2.5| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5|
Long. Pm (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Long. Pm(TOTAL)| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5| 2.5|
Long. Pl (SUS) | 16.3| 16.3| -16.3| -16.3| 0.0| 0.0| 0.0| 0.0|
Long. Pl (OCC) | 12.0| 12.0| -13.3| -13.3| -1.2| -1.2| -1.2| -1.2|
Long. Pl(TOTAL)| 28.3| 28.3| -29.6| -29.6| -1.2| -1.2| -1.2| -1.2|
Long. Q (SUS) | 55.4| -55.4| -55.4| 55.4| 0.0| 0.0| 0.0| 0.0|
Long. Q (OCC) | 40.1| -40.1| -46.2| 46.2| -2.1| 2.1| -2.1| 2.1|
Long. Q (TOTAL)| 95.5| -95.5| -101.6| 101.6| -2.1| 2.1| -2.1| 2.1|
------------------------------------------------------------------------------------------------
Shear Pm (SUS) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pm (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pm(TOTAL)| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Pl (SUS) | 0.0| 0.0| 0.0| 0.0| -4.2| -4.2| 4.2| 4.2|
Shear Pl (OCC) | 0.0| 0.0| 0.0| 0.0| -2.9| -2.9| 2.9| 2.9|
Shear Pl(TOTAL)| 0.0| 0.0| 0.0| 0.0| -7.1| -7.1| 7.1| 7.1|
Shear Q (SUS) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Q (OCC) | 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Shear Q (TOTAL)| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0| 0.0|
Pm (SUS) | 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0|
------------------------------------------------------------------------------------------------
Pm (SUS+OCC) | 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0| 5.0|
------------------------------------------------------------------------------------------------
Pm+Pl (SUS) | 42.9| 42.9| 32.9| 32.9| 8.8| 8.8| 8.8| 8.8|
------------------------------------------------------------------------------------------------
Pm+Pl (SUS+OCC)| 71.1| 71.2| 63.6| 63.5| 14.5| 14.5| 14.5| 14.5|
------------------------------------------------------------------------------------------------
Pm+Pl+Q (Total)| 145.3| 64.7| 140.6| 74.5| 14.2| 15.0| 14.2| 15.0|
Note: Items not derived explicitly will be found in the individual nozzle
calculation. These items include such values as Afls etc.
No interference violations have been detected !
Please refer to the nozzles treated as isolated openings for more information
| |
| |
| |
| |
| |
|\ |
__________/|_\|
| |
| |
|______________|
3D Design Tek Solution 55
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Nozzle Calcs.: S4 Nozl: 7 5:27pm Sep 29,2018
Note: l's equals Iso if no physical diameter limit value is entered. Otherwise
l's considers the physical diameter limit entry.
Available Metal Areas per 9.5-78 to 9.5-81 [Afs, Afb, Afp, Afw]:
Afs = l's * eas = 120.15 * 6.0 = 7.2 cm²
Afb = eb * l'b
= 5.49 * 21.39
= 1.17 cm²
Afp = Ip * min( ea,p ; ec,s ) = 0.0 * 0.0 = 0.0 cm²
Afw = (wshell² + wpad² + winside²) / 2
= (10.0² + 0.0² + 0.0²)/2
= 0.50 cm²
Note: l's equals Iso if no physical diameter limit value is entered. Otherwise
l's considers the physical diameter limit entry.
| |
| |
3D Design Tek Solution 58
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Nozzle Calcs.: S1 Nozl: 8 5:27pm Sep 29,2018
| |
| |
| |
__________/|\ |
____/|__________\|_\|
| |
| |
|____________________|
Note: l's equals Iso if no physical diameter limit value is entered. Otherwise
l's considers the physical diameter limit entry.
= 10.67 cm²
Available Metal Areas per 9.5-78 to 9.5-81 [Afs, Afb, Afp, Afw]:
Afs = (l's + eb )ec,s = (85.06 + 5.49 )6.0 = 5.43cm²
Afb = eb * l'b = 5.49 * 21.39 = 1.17 cm²
Afp = Ip * min( ea,p ; ec,s ) = 22.55 * 6.0 = 1.35 cm²
Afw = (wshell² + wpad² + winside²) / 2
= (10.0² + 4.0² + 0.0²)/2
= 0.58 cm²
| |
| |
3D Design Tek Solution 62
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Nozzle Calcs.: S2 Nozl: 9 5:27pm Sep 29,2018
| |
| |
| |
__________/|\ |
____/|__________\|_\|
| |
| |
|____________________|
Note: l's equals Iso if no physical diameter limit value is entered. Otherwise
l's considers the physical diameter limit entry.
= 10.67 cm²
Available Metal Areas per 9.5-78 to 9.5-81 [Afs, Afb, Afp, Afw]:
Afs = (l's + eb )ec,s = (85.06 + 5.49 )6.0 = 5.43cm²
Afb = eb * l'b = 5.49 * 21.39 = 1.17 cm²
Afp = Ip * min( ea,p ; ec,s ) = 35.55 * 6.0 = 2.13 cm²
Afw = (wshell² + wpad² + winside²) / 2
= (10.0² + 4.0² + 0.0²)/2
= 0.58 cm²
| |
| |
3D Design Tek Solution 66
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Nozzle Calcs.: M1 Nozl: 10 5:27pm Sep 29,2018
| |
| |
| |
__________/|\ |
____/|__________\|_\|
| |
| |
|____________________|
Note: l's equals Iso if no physical diameter limit value is entered. Otherwise
l's considers the physical diameter limit entry.
= 48.18 cm²
Available Metal Areas per 9.5-78 to 9.5-81 [Afs, Afb, Afp, Afw]:
Afs = (l's + eb )ec,s = (85.06 + 8.18 )6.0 = 5.59cm²
Afb = eb * l'b = 8.18 * 41.53 = 3.4 cm²
Afp = Ip * min( ea,p ; ec,s ) = 50.46 * 6.0 = 3.03 cm²
Afw = (wshell² + wpad² + winside²) / 2
= (10.0² + 4.0² + 0.0²)/2
= 0.58 cm²
| |
| |
| |
| |
| |
|\ |
__________/|_\|
| |
| |
|______________|
3D Design Tek Solution 70
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Nozzle Calcs.: S7 Nozl: 11 5:27pm Sep 29,2018
Note: l's equals Iso if no physical diameter limit value is entered. Otherwise
l's considers the physical diameter limit entry.
Available Metal Areas per 9.5-78 to 9.5-81 [Afs, Afb, Afp, Afw]:
Afs = (l's + eb )ec,s = (85.06 + 3.38 )6.0 = 5.31cm²
Afb = eb * l'b = 3.38 * 10.07 = 0.34 cm²
Afp = Ip * min( ea,p ; ec,s ) = 0.0 * 0.0 = 0.0 cm²
Afw = (wshell² + wpad² + winside²) / 2
= (10.0² + 0.0² + 0.0²)/2
= 0.50 cm²
3D Design Tek Solution 71
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Nozzle Calcs.: S7 Nozl: 11 5:27pm Sep 29,2018
| |
| |
| |
| |
| |
|\ |
__________/|_\|
| |
| |
|______________|
3D Design Tek Solution 74
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Nozzle Calcs.: S3 Nozl: 12 5:27pm Sep 29,2018
Note: l's equals Iso if no physical diameter limit value is entered. Otherwise
l's considers the physical diameter limit entry.
Available Metal Areas per 9.5-78 to 9.5-81 [Afs, Afb, Afp, Afw]:
Afs = l's * eas = 120.15 * 6.0 = 7.2 cm²
Afb = eb * l'b
= 3.38 * 10.07
= 0.34 cm²
Afp = Ip * min( ea,p ; ec,s ) = 0.0 * 0.0 = 0.0 cm²
Afw = (wshell² + wpad² + winside²) / 2
= (10.0² + 0.0² + 0.0²)/2
= 0.50 cm²
Note: l's equals Iso if no physical diameter limit value is entered. Otherwise
l's considers the physical diameter limit entry.
Nozzle Schedule:
For hub nozzles, the thickness and diameter shown are those of the smaller
and thinner section.
Note: The Outside projections below do not include the flange thickness.
Max. Wind Shear on one Leg (top & bottom) 108. Kgf
Max. Earthq. Shear on one Leg (top & bottom) 4. Kgf
Max. Wind Moment at base of one Leg 86. Kg-m.
Max. Earthquake Moment at base of one Leg 3. Kg-m.
Max. Vertical Load (Wt. + Wind) on one Leg 832. Kgf
Max. Vertical Load (Wt. + Eq.) on one Leg 255. Kgf
Note:
Wind and Earthquake moments include the effects of user defined
forces and moments if any exist in the job and were specified
3D Design Tek Solution 79
Cooling Water Circuit Expansion Tank
Tank 88304
PV Elite 2017 Licensee: SPLM Licensed User
FileName : Tank 88304
Vessel Design Summary: Step: 27 5:27pm Sep 29,2018
Weights:
Fabricated - Bare W/O Removable Internals 1032.3 kg.
Shop Test - Fabricated + Water ( Full ) 4200.4 kg.
Shipping - Fab. + Rem. Intls.+ Shipping App. 1032.3 kg.
Erected - Fab. + Rem. Intls.+ Insul. (etc) 1032.3 kg.
Empty - Fab. + Intls. + Details + Wghts. 1032.3 kg.
Operating - Empty + Operating Liquid (No CA) 1032.3 kg.
Field Test - Empty Weight + Water (Full) 4200.4 kg.