Blisters is a defect of bricks, which is due to

A. Excess of iron

B. Excess of magnisa

C. Water

D. Air

The small area on painted surface enclosed by hair line cracks are known as*

A. Blistering

B. Crazing

C. Wrinkling

D. Chalking

Least count of Prismatic compass and Surveyor compass is*

A. 15' and 30'

B. 30' and 15'

C. 20' and 15'

D. 15' and 20'

A fluid which shear strength is directly proportional rate of change of velocity then fluid is*

A. Non Newtonian fluid

B. Ideal plastic

C. Ideal

D. Real

For a cantilever beam of length L built in at the support and restrained against torsion at the free end,
the effective projecting length is*

A. l=0.7L

B. l=0.75L

C. l=0.85L

D. None of these
Bentonite soil are*

A. residual soil

B. organic soil

C. expansion soil

D. ash soil

Which Compact equipment used for core of earth dam*

A. Pneumatic tyred roller

B. Sheep foot roller

C. Frog Hammer

D. Grid roller

Which is not a soil sheet

A. Burcite Sheet

B. Gibbsite Sheet

C. Morphite Sheet

D. Silica Sheet

Which of the following methods used for structural analysis is not a deflection based method*?

A. Kani method

B. column analogy method

C. moment distribution method

D. slope deflection method

Centre gravity of cone*

A. h/2

B. h/3

C. h/4

D. 2h/3
[12/25, 5:35 PM] Atif Junior Taunsa: *A beam of uniform strength contains same*

A. bending moment

B. bending stress

C. deflection

D. stiffness

Concrete is unsuitable for compaction by a vibrator if it is

A) dry

B) earth moist

C) semi-plastic

D) plastic

E) none of these

Navier stokes equation is used in analysis of*

A) viscous flow

B) non viscous

C) turbulent

D) rotational

Which one of the following section performs better on the ductility Criterion*?

A. balanced section

B.over reinforced section

C. under reinforced section

D. non Prismatic section

For reinforced concrete exposed to sulphate attack minimum grade required is*

A. M10

B. M15

C. M20
D. M25

In limit state approach, spacing of main reinforcement controls primarly*

A. collapse

B. cracking

C. deflection

D. durability

In Rcc beams, as the % area of tensile steel increases*

A. Depth of neutral Axis increase

B. Depth of neutral Axis decreases

C. Depth of neutral Axis does not change

D. Lever arm increase

In a combined footing for two columns caring unequal load, the maximum hogging moment occurs at

A. Inside face of the heavier column

B. a section equidistant from both the column

C. a section having maximum share force

D. a section having zero share force

In an open channel flow,the maximum velocity occurs*

A. Just below the free surface

B. at the surface

C. near the channel bottom

D. in the mid-depth of flow

The best coagulant for removing the colour of water is*

A. Lime

B. Alum

C. Copper sulphate
D. Iron sulphate

Degree of consolidation is

A. directly proportional to time and inversely proportional to drainage path

B. directly proportional to square of drainage path and inversely proportional to time

C. directly proportional to time and inversely proportional to square of the drainage path

D. directly proportional to drainage path and inversely proportional to time

Coefficient of consolidation is used to calculate*

A. time rate of settlement

B. total settlement

C. preconsolidation process

D. stress in the field

In a continuous bending moment curve the point where it changes sign, is called*

A. point of inflexion

B. point of contra-flexture

C. point of virtual hinge

D. all the above.

Most appropriate hot rolled Indian standard section for steel girder is*

A. ISLB

B. ISWB

C. ISHB

D. ISMB

Which one of is not mechanical property of brick*

A. Texture

B. Modulus of rapture

C. Fire resistance
D. Tensile strength

A concrete mix has entrapped air about 1% result in*

A. Required less quantity of water

B. Poor quality of concrete

C. Average quality of concrete

D. Improved quality of concrete

The quantity cement concrete damp proofing courses measured in terms of*

A. m

B. m²

C. m³

D. Lump sum

The spillway crest is located at

A. Max. Water level at dam

B. Normal pool level

C. Crest of dam

Fish ladder is provided on the side of

A. Divide wall

B. Core wall

C. Diaphragm wall

D. Wing wall

Which operation cannot be done easily on mild steel*?

A. drilling

B. punching

C. cutting

D. hardening
For measuring very low pressure which of the following you will use*?

A. Barometer

B. Manometer

C. Piezometer

D. None of these

The alignment of highways are generally taken along*

A. Along the contour line

B. Across the contour line

C. The valley line

D. The ridge line

In the hydraulic jump, the flow condition is*

A. Gradually varied

B. Rapid

C. Unsteady

D. None

When shear stress exceeds the permissible limit in a slab, then it is reduced by*

a) increasing the depth

b) providing shear reinforcement

c) using high strength steel

d) using thinner bars but more in number

The ratio of 28 days strength of cube to that of a standard cylinder is*

A. 0.8

B. 1.25

C. 0.67

D. 1
Co-efficient of friction for laminar flow*

A. 16/Ré

B. 64/Ré

C. 24/Ré

D. 6/Ré

Atmospheric pressure varies with*

A. Altitude

B. Temperature

C. Weather conditions

D. None

In order to know the workmanship of lime which test is performed*?

A.Impunity teast

B.Ball test

C.Hydraulic lime test

D.Workability test

Rivet are used for ......... fastenings

Permmanent

Temporary

the length of a cantilever carrying an isolated load at its free end is doubled, the deflection of the free
end will increase by*

1/8

1/3

Bolts are used for ......... fastenings*

Permmanent
Temporary

If the width of a simply supported beam carrying an isolated load at its centre is doubled, the deflection
of the beam at the centre is changed by* (A)2 times (B)4 times (C)8 times (D)1/2 times

When loads are applied proportionately to a frame structure containing its members in one plane, the
structure is called*

(A)Grid frame (B)Plane frame (C)Space frame (D)Truss frame

Shear force for a cantilever carrying a uniformly distributed load over its length, is*

(A)Triangle (B)Rectangle (C)Parabola (D)Cubic parabola

The ratio of strengths of solid to hollow shafts, both having outside diameter D and hollow having inside
diameter D/2, in torsion, is*

(A)1/4 (B)1/2 (C)1/16 (D)15/15

Hooks Law holds upto*

Yield limit

Or

Proportional limit

With the same cross-sectional area and immersed in same turbulent flow the largest total drag will be on

A. A sphere

B. A cylinder

C. A streamlined body

D. A circular disc of plate held normal to flow

Coefficient of contraction for an external cylindrical mouthpiece is*

A. 1

B. 0.855

C. 0.70

D. 0.611

Methomoglobinemia disease is caused in children by*

A. Conversion of nitrites to nitrates

C. Both A and B

D. Reaction between haemoglobin and carbon dioxide

The difference between Face left and face right observations of a theodolight is 3'. The error is*

A. 3'

B. 45"

C. 1'30"

D. 0'

[12/28, 12:16 AM] Atif Junior Taunsa: *What is difference between crest and sill*?????

[12/28, 12:20 AM] Atif Junior Taunsa: *Consolidation is a result of*

A. Specific gravity of soil

B. Lowering of ground water table

C. Self-weight of soil and external load from structure

D. Expulsion of water from pores

[12/28, 12:20 AM] Atif Junior Taunsa: *The relative stability of sewage sample,w hose dissolved oxygen is
same as the total oxygen required to satisfy BOD is*

A. Zero

B. 1

C. Infinity

D. 100

[12/28, 12:21 AM] Atif Junior Taunsa: *an ideal transition curve is*

A. Bernoulli's lemniscate

B. Clothoid

C. Parabola

D. Cubic parabola
[12/28, 12:22 AM] Atif Junior Taunsa: *For testing compressive strength of cement, the size of cube used
is*

A. 50 mm

B. 70.6 mm

C. 100 mm

D. 150 mm

[12/28, 12:23 AM] Atif Junior Taunsa: *The power transmitted by hollow shaft will be more than that of
solid shaft if their weight and density both are*

A. Equal

B. Half

C. One fourth

D. None of the above

[12/28, 12:25 AM] Atif Junior Taunsa: *Shear strength of timber depends on which one of the following*

A. Heart wood

B. Medullary rays

C. SAP wood

D. Lignin with fiber

E. Outer bark

[12/28, 12:26 AM] Atif Junior Taunsa: *The defect in wood due to hardening is*

A. Burls

B. Shakes

C. Twisted fiber

D. None

[12/28, 12:28 AM] Atif Junior Taunsa: *For strip spread footing,ratio of length to width is*

A. L/B <10

B. L/B >= 10
C. L=B

D. B is very small

[12/28, 12:28 AM] Atif Junior Taunsa: *Bentonite soil are*

A. Residual soil

B. Organic soil

C. Expensive soil

D. Ash soil

[12/28, 12:28 AM] Atif Junior Taunsa: *Strain energy per unit volume of a solid circular shaft under axial
tension is*

A. f²/2E

B. f²/4E

C. f²/8E

D. f²/16E

[12/28, 12:30 AM] Atif Junior Taunsa: *For hypersonic flow, the Mach number is*

(a) unity

(b) greater than unity

(c) greater than 2

(d) greater than 4

(e) greater than 10

[12/28, 12:31 AM] Atif Junior Taunsa: *The upper surface of a weir over which water flows is known is*

(a) crest

(b) nappe

(c) sill

(d) weir top

(e) contracta.

*most imp McQ*

(a) energy/unit area

(b) distance

(c) both of the above

(d) it has no units

(e) none of the above.

[12/28, 12:33 AM] Atif Junior Taunsa: *A pressure of 25 m of head of water is equal to*

(a) 25 kN/m²

(b) 245 kN/m²

(c) 2500 kN/m²

(d) 2.5kN/m²

(e) 12.5 kN/m²

[12/28, 12:34 AM] Atif Junior Taunsa: *The capillary rise at 20°C in a clean glass tube of 1 mm bore
containing water is approximately*

(a) 1 mm

(b) 5 mm

(c) 10 mm

(d) 20 mm

(e) 30 mm

[12/28, 12:36 AM] Atif Junior Taunsa: *The pressure intensity inside a droplet is given by*

a. P=4σ/r

b. P=2 σ/r

c. P=6σ/r

d. P=0.5σ/r

[12/28, 12:30 PM] Atif Junior Taunsa: *Pressure at the Summit of the siphon is*

A. Equal to atmospheric
B. More than atmospheric

C. Less than atmospheric

D. None of these

[12/28, 12:30 PM] Atif Junior Taunsa: *Plywood is made from*

A. Common timber

B. Teak wood only

C. Bamboo fiber

D. Asbestos sheet

[12/28, 12:31 PM] Atif Junior Taunsa: *The minimum thickness of a rainforced concrete wall should be*

A. 7.5 cm

B. 10 cm

C. 12 cm

D. 15 cm

[12/28, 12:32 PM] Atif Junior Taunsa: *Dry rot*

A. Cracks the timber

B. Reduces the timber to powder

C. Reduce the strength of timber

D. Shrink the timber

[12/28, 12:34 PM] Atif Junior Taunsa: *The density of concrete...............with increase in the size of
aggregate*

1) does not change

2) increases

3) decreases

[12/28, 12:34 PM] Atif Junior Taunsa: *The mould size of the cube for testing the compressive strength
of cement is*

A. 70.6 mm
B. 150 mm

C. 75 mm

[12/28, 12:36 PM] Atif Junior Taunsa: *The temporary adjustment of a prismatic compass are*

A. Centering

B. Adjustment of level

C. Adjustment of needles

D. Adjustment of van

[12/28, 12:37 PM] Atif Junior Taunsa: *The unit of mass- moment of inertia is*

A. Kg-m³

B. Kg-m⁴

C. Kg-m

D. Kg-m²

[12/28, 12:39 PM] Atif Junior Taunsa: *if a composite bar of Steel and copper is heated, the copper bar
will be under*

A. Tension

B. Compression

C. shear

D. Torsion

[12/28, 12:39 PM] Atif Junior Taunsa: *Water cement ratio by weight as compared to water cement ratio
by volume is*

A. Greater

B. Less

C. Equal

D. Not equal

[12/28, 3:51 PM] Atif Junior Taunsa: *Road roughness is measured using*

A. Bump integrator
B. Dynamic cone penetrometer

C. failing weight deflectometer

D. Bankelman beam

[12/28, 3:59 PM] Atif Junior Taunsa: *sand particles are made of*

A. Kailinite

B. Montmorillonite

C. Illite

D. Quartz

[12/28, 4:00 PM] Atif Junior Taunsa: *creep is the*

a. lateral movement of rail

b. vertical movement of rail

c. longitudinal movement of rail

d. difference in level of 2 rails.

[12/28, 4:01 PM] Atif Junior Taunsa: *The rate of BOD exerted at any time is*

a. directly proportional to BOD satisfied

b. directly proportional to BOD remaining

c. inversely proportional to BOD satisfied

d. inversely proportional to BOD remaining.

[12/28, 4:02 PM] Atif Junior Taunsa: *A Dowel is a*

a. Fastener

b. Support

c. Joint in wooden pieces

d. Tool used in woodwork

[12/28, 4:04 PM] Atif Junior Taunsa: *the liquid limit, plastic limit and the shrinkage limit of cohesive soil
satisfy the relation*

a. LL> PL <SL
b. LL>PL>SL

c. LL<PL<SL

d. LL<PL>SL

[12/28, 4:07 PM] Atif Junior Taunsa: *A beam of uniform strength will have at every cross section*

1 same deflection

2 same stiffness

3 same bending moment

4 same bending stress

[12/28, 4:08 PM] Atif Junior Taunsa: *The consistency and flow resistance of bitumen can be determined
from the following*

(a) Ductitility test

(b) Penetration test

(c) Softening point test

(d) Viscosity test

[12/28, 4:10 PM] Atif Junior Taunsa: *the centre of gravity of a semicircle of radius r from the diameter
is*

a. 3r/2π

b. 4r/3π

c. 3r/4π

d. 2r/3π

[12/28, 6:55 PM] +92 315 9721912: With explanation..

If 50-kg of fine aggregate and 100kg of coarse aggregate are mixed in a concrete whose w/c ratio is 0.6
the weight of water required for harsh mix is

A)8kg

B)10kg
C)12kg

D)14kg

Plz tell me formula of it

[12/28, 7:47 PM] +92 335 6742632: OPC:(Ordinary Portland cement)

Initial setting time = 30 min.

Final setting time = 10 hours.

LPC:(Lime pozzolana cement)

Initial setting time= 120 min (2 hours).

Final setting time = 6 hours.

High alumina cement:

Initial setting time= 3.5 hours.

Final setting time= 5 hours.

[12/28, 8:56 PM] Atif Junior Taunsa: *Normal stress at toe is*

A.positive

B.negative

[12/28, 8:56 PM] Atif Junior Taunsa: *Normal stress at heel is*

A.positive

B.negative

[12/28, 9:01 PM] +92 315 9721912: Maximum pitch of rivets, used in steel stacks, is limited to

(A)6 t (B)10 t (C)12 t (D)16 t

[12/29, 6:36 PM] Atif Junior Taunsa: *Yeilding of steel in singly reinforces beam occurs in*

A) Balanced reinforced beam

c) over reinforced beam

D) None

[12/29, 6:36 PM] Atif Junior Taunsa: *Yeilding of steel in Doubly reinforces beam occurs in*

A) Balanced reinforced beam

B ) Under reinforced beam

c) over reinforced beam

D) None

[12/29, 6:42 PM] Atif Junior Taunsa: *The compound of Portland cement which contributes to the
strength after two to three years is*

A.Tricalcium silicateB.Di-calcium silicateC.Trica

lcium aluminateD.Tetracalcium alumino ferrite.

[12/29, 6:53 PM] Atif Junior Taunsa: *The rocks which are formed due to cooling of magma at a
considerable depth from earth's surface are called*

A.Plutonic rocksB.Hypabyssal rocksC.Volcanic rocksD.Igneous rocks

Ye

[12/29, 6:54 PM] Atif Junior Taunsa: *In a two hinged arch an increase in temperature induces*

A. No bending moment in the arch rib

B. Uniform bending moment in the arch rib

C. Maximum bending moment at the crown

D. Minimum bending moment at the crown

[12/29, 7:04 PM] Atif Junior Taunsa: *The force polygon representing a set of forces in equilibrium is a*

(A) Triangle

(B) Open polygon

(C) Closed polygon

(D) Parallelogram
[12/29, 7:06 PM] Atif Junior Taunsa: *A stone is whirled in a vertical circle, the tension in the string, is
maximum*:

(A) When the string is horizontal

(B) When the stone is at the highest position

(C) When the stone is at the lowest position

(D) At all the positions

[12/29, 7:09 PM] Atif Junior Taunsa: *The maximum pull in a cable, carrying a uniformly distributed load
and supported at two ends which are at the same level* is at :

(A) Supports

(B) Quarter span

(C) Mid span

(D) None of the above

[12/29, 7:10 PM] Atif Junior Taunsa: *Coefficient of friction depends on* :

(A) Nature of surfaces only

(B) Area of contact only

(C) Both (A) and (B)

(D) None of the above

[12/29, 7:14 PM] Atif Junior Taunsa: *Three forces which act on a rigid body to keep it in equilibrium.
The forces must be coplanar and* :

(A) Concurrent

(B) Parallel

(C) Concurrent parallel

(D) None of these

[12/29, 7:14 PM] Atif Junior Taunsa: *Pick up the correct statement from the following. The kinetic
energy of a body* :

(A) Before impact is equal to that after impact

(B) Before impact is less than that after impact

(D) Remain constant

[12/29, 7:18 PM] Atif Junior Taunsa: *The inherent property of a body which offers reluctance to change
its state of rest or uniform motion, is* :

(A) Weight

(B) Mass

(C) Inertia

(D) Momentum

[12/29, 7:18 PM] Atif Junior Taunsa: *The shape of a suspended cable under its own weight, is*:

(A) Parabolic

(B) Circular

(C) Catenary

(D) Elliptical

[12/29, 7:19 PM] Atif Junior Taunsa: *The tension in a cable supporting a lift*:

(A) Is more when the lift is moving downwards

(B) Is less when the lift is moving upwards

(C) Remains constant whether its moves downwards or upwards

(D) Is less when the lift is moving downwards

[12/29, 7:20 PM] Atif Junior Taunsa: *particle executes a simple harmonic motion. While passing through
the mean position, the*;

particle possesses :

(A) Maximum kinetic energy and minimum potential energy

(B) Maximum kinetic energy and maximum potential energy

(C) Minimum kinetic energy and maximum potential energy

(D) Minimum kinetic, energy and minimum potential energy

[12/29, 7:24 PM] Atif Junior Taunsa: *In which of the following trusses, the method of substitution is
required for determining the forces in all the members of the truss by graphic statics*?
(A) Howe truss

(B) King post truss

(C} Finktruss

(D) Warren truss

[12/29, 7:27 PM] Atif Junior Taunsa: *The graphical method of determining the forces In the members of
a truss is based on* :

(A) Method of Joint

(B) Method of section

(C) Either method

(D) None of the two methods

[12/29, 7:28 PM] Atif Junior Taunsa: *Free body diagram is an* :

(A) Isolated Joint with only body forces acting on it

(B) Isolated Joint with internal forces acting on it

(C) Isolated Joint with all the forces, internal as well as external, acting on it

(D) None of the above

[12/29, 7:31 PM] Atif Junior Taunsa: *A light rope is loaded with many equal weights at equal horizontal
intervals, The points of*

suspension on the rope lie on a :

(A) Parabola

(B) Catenry

(C) Cycloid

(D) Ellipse

[12/29, 7:31 PM] +92 315 9721912: If there are m unknown member forces, r unknown reaction
components and j number of joints, then the degree of static indeterminacy of a pin-jointed plane frame
is given by

a) m + r + 2j

b) m - r + 2j
c) m + r - 2j

d) m + r - 3j

[12/29, 7:31 PM] +92 315 9721912: Number of unknown internal forces in each member of a rigid
jointed plane frame is

a) 1

b) 2

c) 3

d) 6

[12/29, 7:32 PM] Atif Junior Taunsa: *A light rope is loaded with many equal weights at equal horizontal
intervals, The points of*

suspension on the rope lie on a :

(A) Parabola

(B) Catenry

(C) Cycloid

(D) Ellipse

[12/29, 7:34 PM] Atif Junior Taunsa: *When a circular wheel rolls on a straight track, then the shape of
body centrode and space*

centrode respectively are :

(A) Straight line and parabola

(B) Straight line and circle

(C) Circle and straight line

(D) Circle and parabola

[12/29, 7:39 PM] Atif Junior Taunsa: *The member forces in a statically in determinate truss*:

(A) Can be obtained by graphic statics

(B) Cannot be obtained by graphic statics

(C) Maybe obtained by graphic statics

(D) Can be obtained by graphic statics by trial and error

(A) Can be obtained by graphic statics

(B) Cannot be obtained by graphic statics

(C) Maybe obtained by graphic statics

(D) Can be obtained by graphic statics by trial and error

[12/29, 7:47 PM] Atif Junior Taunsa: *While estimating the qualities for the construction of a building,
the correct metric unit is*:

(A) Metre for length

(B) Cubic metre for area

(C) Square metres for volume

(D) Litre for capacity

[12/29, 7:52 PM] Atif Junior Taunsa: *If the formation level of a highway has a uniform gradient for a
particular length, and the ground is also having a longitudinal slope, the earthworkmay be calculated by*
:

(A) Mid-section formula

(B) Trapezoidal formula

(C) Prismoidal formula

(D) All the above

[12/29, 7:56 PM] Atif Junior Taunsa: *The plinth area of a building not includes* :

(A) Area of the walls at the floor level

(B) Internal shaft for sanitary installations up to 2 sq m. in area

(C) Lift and wall including landing

(D) Area of cantilevered porch

[12/29, 7:58 PM] Atif Junior Taunsa: *The main factor to be considered while preparing a detailed
estimate, is*:

(A) Quantity of the materials

(B) Availability of materials

(D) All the above

[12/29, 7:58 PM] Atif Junior Taunsa: *The rate of an item of work depends on* :

(A) Specifications of works

(B) Specifications of materials

(C) Proportion of mortar

(D) All the above

[12/29, 8:00 PM] Atif Junior Taunsa: *The rate of payment is made for 100 cu m (per % cu m) in case of*:

(A) Earth work in excavation

(B) Rock cutting

(C) Excavation in trenches for foundation

(D) All the above

[12/30, 10:38 PM] Atif Junior Taunsa: *The maximum efficiency of BOD removal is achieved in*

A. Oxidation pond.

B. Oxidation ditch

C. Aerated lagoons

D. Trickling filters

[12/30, 10:38 PM] Atif Junior Taunsa: *Non Scouring Velocity in different sewers*

Vitrified Tiles and Glazed Bricks => 4.5 to 5.5 m/sec.

Cast - Iron sewer => 3.5 to 4.5 m/sec.

Stoneware Sewer => 3 to 4 m/sec.

Cement Concrete Sewer => 2.5 to 3 m/sec.

Ordinary Brick Line Sewer => 1.5 to 2.5 m/sec.

Earthen Sewer => 0.6 to 1.2 m/sec..

[12/30, 10:38 PM] Atif Junior Taunsa: *the sewers of circular sections are most suitable when they run:*
A. Half full

B. One-third full

C. Two-third full

D. Completely full

[12/30, 10:38 PM] Atif Junior Taunsa: The effective length of a compression member of length L, held in
position and restrained in direction at both ends, is (A)L (B)0.67 L (C)0.85 L (D)1.5 L

[12/31, 9:51 AM] Atif Junior Taunsa: *The cementing property in cement mainly due to*

A. Lime

B. Silica

C. Iron oxide

D. Alumina

[12/31, 9:53 AM] Atif Junior Taunsa: *What is the maximum size that can be used in plain concrete*?

c) 100 mm

d) 80 mm

[12/31, 9:55 AM] Atif Junior Taunsa: *Ideal vertical curve is*

1 True spiral

2cubical spiral

3 cubical parabola

4 lamniscate

[12/31, 9:59 AM] Atif Junior Taunsa: *The constituent in lime which retard the slaking action and
increase the rapidity of setting is*

A. Silica

B. Sulphate

C. Alkalies

D. Alumina

[12/31, 9:59 AM] Atif Junior Taunsa: *Gantry guiders are designed to resists*
A) lateral loads

B) longitudinal and vertical loads

C) lateral, longitudinal and vertical loads

D) lateral and longitudinal loads

[12/31, 9:59 AM] Atif Junior Taunsa: *The cross-section of a standard fillet is a triangle whose base
angles are* (A)45° and 45° (B)30° and 60° (C)40° and 50° (D)20° and 70°

[12/31, 10:06 AM] Atif Junior Taunsa: Pakistan Navigation System is similar to GPS of USA is called as

A) Bhavun

B) Glonass

C) Galileo

D) Navic

E) A and B

[12/31, 10:06 AM] Atif Junior Taunsa: Q18.Shingle is

A. decomposed laterite

B. crushed granite

C. water bound pebbles

D. air weathered rock.

[12/31, 10:06 AM] +92 315 9721912: 7. Pick up the correct statement from the

following :

A. pH value indicates acidity and alkalinity of sewage

B. In acidic sewage, the pH value is less than 7

C. In alkaline sewage, the pH value is more than 7

D. Fresh sewage is generally alkaline

E. All the above.

[12/31, 10:52 AM] +92 315 9721912: An open traverse can be checked by
A) Astronomical Observation

B) Included angles

C) Deflection angles

D) linear measurements

[12/31, 10:53 AM] +92 315 9721912: Q2.The variety of pig iron used for the manufacture of steel by
Bessemer process, is

A. Bessemer pig

B. Grey pig

C. White forge pig

D. Mottled pig.

[12/31, 10:54 AM] +92 315 9721912: Q13.Mastic asphalt is generally used for

A. damp proof course

B. water proof layer

C. partition walls

D. both (a) and (b).

[12/31, 10:56 AM] +92 315 9721912: Q. The gravitational force on the body is called ....?

A. Acceleration

B. Force

C. Weight

D. None of these

The type of transition curves generally provided on hill roads, is (A)Circular (B)Cubic parabola
(C)Lemniscate (D)Spiral

[1/3, 10:49 PM] +92 310 8708829: Atmospheric pressure varies

Temp

Weather Condition

All of these

[1/3, 10:54 PM] +92 315 9721912: The floor is rubbed with oxalic acid, for making its surface

A. free from voids

B. glossy

C. durable

D. uniform.

[1/3, 10:54 PM] +92 315 9721912: A soil having uniformity coefficient more than 10,is called

Uniform soil

Poor soil

Well graded soil

Coarse soil

[1/3, 10:57 PM] +92 313 5480059: The highest point on the extrados is called

a. Skew back

b. Crown

c. Voussoir

d. Keystone

[1/3, 11:07 PM] +92 310 8708829: As compared to roadways maintenance cost. Of railway is

a same

b more

c less
d Depends on region

[1/3, 11:10 PM] +92 310 8708829: The ability of a material to resist deformation is said to be__

a Strength

b Toughness

c plasticity

d Brittleness

[1/3, 11:13 PM] +92 310 8708829: The seepage force in soil is proportional to__

a Exit gradient

b Head of water at upstream

c Head of water at downstream

d All of the above

[1/3, 11:18 PM] +92 310 8708829: Silt have the following property__

Plasticity

Limited plasticity

No plasticity

Elasticity

[1/3, 11:23 PM] +92 310 8708829: A soil having uniformity coefficient more than 10,is called

Uniform soil

Poor soil

Well graded soil

Coarse soil

*Water reducing admixtures can typically reduce the water content in concrte which is equal to*.???

A.5_10%

B.11_15%

C.16_20%
D.21_25%

[1/17, 11:05 AM] Atif Junior Taunsa: *The retained wall in continuation of abutments both upstream and
downstream is called as*-

A)Base wall

B)Parapet wall

C)Border wall

D)Flank wall

[1/17, 11:05 AM] Atif Junior Taunsa: Excess of Alkali in cement results in:

a) Dry cement paste

b) Efflorescence

c) Less plasticity

d) Unsound cement

[1/17, 11:05 AM] Atif Junior Taunsa: What is the abbreviation of PPC?

a) Perfect Portland Cement

b) Portland Produced Cement

c) Portland Pozzolana Cement

d) Productive Portland Cement

[1/17, 11:05 AM] Atif Junior Taunsa: Which of the following types of cement is used in marine
structures?

a) Expanding cement

b) High alumina cement

c) Blast furnace slag cement

d) White cement
[1/17, 11:06 AM] Atif Junior Taunsa: The specific gravity for sand is:

a) 2.6

b) 2.65

c) 2.8

d) 2.75

[1/17, 11:06 AM] Atif Junior Taunsa: The brick laid with its length parallel to the face of a wall, is a known
as

A. Header

B. Stretcher

C. Closer

D. None of these

[1/17, 11:07 AM] Atif Junior Taunsa: *Which of the following ingredients of cement, when added in
excess quantity, causes the cement to setslowly*?

A)Alumina

B)Silica

C)Iron oxide

D)Lime

[1/17, 11:07 AM] Atif Junior Taunsa: The method of moving each brick through a small horizontal
distance before it is finally laid in any brick wall and pressing it by means of brick hammer, is known as

A.Troweling

B. Laying

C. Grouting

D. Placing

[1/17, 11:07 AM] Atif Junior Taunsa: The vertical side member of a shutter frame, is known

A. Style

B. Reveal
C. Mullion

D. Post

[1/17, 11:08 AM] Atif Junior Taunsa: *The period of cleaning of a slow sand filter, is usually*-

A)5 to 10 days

B)Three months to six months

C)One month to three months

D)Two weeks to three weeks

[1/17, 11:09 AM] Atif Junior Taunsa: To support a heavy structure in sandy soil, the type of foundation
generally used, is

A. Combined footing

B. Raft footing

C. Pier footing

D. Strap footing

[1/17, 11:09 AM] Atif Junior Taunsa: The local swelling of a finished plaster, is termed

A. Cracking

B. Hacking

C. Blistering

D. Screading

[1/17, 11:09 AM] Atif Junior Taunsa: A temporary rigid structure having platforms to enable masons to
work at different stages of a building, is known as

A. Scaffolding

B. Underpinning

C. Shoring

D. Centering

[1/17, 11:10 AM] Atif Junior Taunsa: *Stone is rejected if water absorption is more than*,

a)5%
b)10%

c)15%

d)20%

[1/17, 11:11 AM] Atif Junior Taunsa: *The thickness of rebate is normally kept*,

a)1cm

b)2cm

c)3cm

d)4cm

[1/17, 11:12 AM] Atif Junior Taunsa: *The straight line between two station is*,

a) traverse

b) traverse angle

c)straight line

d)traverse leg

[1/17, 11:12 AM] Atif Junior Taunsa: In soils possessing low bearing capacity, the type of foundation
generally provided, is

A. Column footing

B. Grillage footing

C. Raft footing

D. All the above

[1/17, 11:12 AM] Atif Junior Taunsa: The maximum number of jets, generally, employed in an impulse
turbine without jet interference are

A. two B. four

C. six D. eight

[1/17, 11:12 AM] Atif Junior Taunsa: A coarse-grained soil has a voids ratio 0.75, and specific gravity as
2.75. The critical gradient at which quick sand condition occurs, is

A. 0.25
B. 0.50

C. 0.75

D. 1.00

Answer: Option D

[1/17, 11:12 AM] Atif Junior Taunsa: Failure of the stability of slopes, generally occurs along

A. slip plane

B. a horizontal surface

C.

a curved surface

D. all the surfaces.

Answer: Option C

[1/17, 11:12 AM] Atif Junior Taunsa: The area covered by all floors of the building is called-

A)Carpet area

B)Floor area

C)Built up area

D)Floor space index

[1/17, 11:12 AM] Atif Junior Taunsa: A rapid test to indicate the intensity of pollution of water is-

A)Total Dissolved Solids

B)Most Probable Number

C)Biochemical Oxygen Demand

D)Dissolved Oxygen

[1/17, 11:12 AM] Atif Junior Taunsa: Which piles are formed by driving a steel tube and shoe, filling with
concrete, using upward extracting anddownward tamping blows alternatively?

A)Vibro pile

B)Franky pile
C)Duplex pile

D)Mac Arthur pile