NSX-T99 LH

NSX-T99E HA

SERVICE MANUAL
COMPACT DISC STEREO BASIC TAPE MECHANISM : 2ZM-3MK2 PR4NM
CASSETTE RECEIVER BASIC CD MECHANISM : 6ZG-1 ZRNDM

CD REMOTE
SYSTEM CASSEIVER SPEAKERS CONTROL
NSX-T99 CX-NT99
SX-WNT99 RC-ZAS04
NSX-T99E CX-NT99E

• This Service Manual is the “Revision Publishing” and replaces “Simple Manual”
NSX-T99/T99E, (S/M Code No. 09-002-426-5T1).

• If requiring information about the CD mechanisim, see Service Manual of 6ZG-1,

(S/M Code No. 09-001-338-7N2)
N
SIO
VI
RE

TA
DA

S/M Code No. 09-003-426-5R1

 SPECIFICATIONS

<FM Tuner section> <Compact disc player section>

Tuning range 87.5 MHz to 108 MHz Laser Semiconductor laser (λ =780 nm)
Usable sensitivity(IHF) 13.2 dBf D-A converter 1 bit dual
Antenna terminals 75 ohms (unbalanced) Signal-to-noise ratio 83 dB (1 kHz, 0 dB)
Harmonic distortion 0.05 % (1 kHz, 0 dB)
<AM Tuner section> Wow and flutter Unmeasurable
Tuning range 531 kHz to 1602 kHz (9 kHz step)
530 kHz to 1710 kHz (10 kHz step) <Speaker system SX–WNT99>
Usable sensitivity 350 uV/m Cabinet type 4 way, built-in subwoofer
Antenna Loop antenna Speakers Subwoofer :
200 mm ( 77/8 in.) cone type
<Amplifier section> Mid range:
Mid-high frequency amplifier 100 mm ( 315/16 in.) cone type
Power output* Rated: 56 W + 56 W Tweeter :
(8 ohms, THD 1 %,1 kHz) 60 mm ( 23/8 in.) cone type
Reference: 70 W + 70 W Super Tweeter :
(8 ohms, THD 10 %,1 kHz) 20 mm (13/16 in.) ceramic type
Total harmonic distortion 0.3 % (28 W, 1 kHz, 8 ohms, Impedance 6 ohms / 8 ohms
DIN AUDIO) Output sound pressure level 87 dB/W/m
Low frequency amplifier Dimensions (W x H x D) 260 x 463 x 314 mm
Power output* Rated: 167 W + 167 W (101/4 x 181/4 x 123/8 in..)
(6 ohms, THD 1 %,75 Hz) Weight 8.0 kg (17 lbs. 10 oz)
Reference: 210 W + 210 W
(6 ohms, THD 10 %,75 Hz) <General>
Total harmonic distortion 0.3 % (84 W,75 Hz,6 ohms, Power requirements 120 V/220-230 V/240 V
DIN AUDIO) (switchable ) 50/60Hz
* without connecting to surround speakers Power consumption 275W
Inputs VIDEO/AUX : 300 mV (adjustable) Dimensions of main unit 300 x 382.6 x 396.4mm
MD : 300 mV (adjustable) (117/8 x 151/8 x 15 5/8in.)
MIC1,MIC2 : 1.0 mV (10 kohms) Weight of main unit 13.7 kg (30 lbs. 3 oz)
LINE OUT : 150 mV
Outputs SPEAKERS HIGH FREQ : Standby power consumption
accept speakers of 8 ohms or more If the power-economizing mode is OFF: 36 W
SPEAKERS LOW FREQ : If the power-economizing mode is ON: 0.9 W
accept speakers of 6 ohms or more
SURROUND SPEAKERS : accept
speakers of 8 to 16 ohms
PHONES (stereo jack) : accepts • Design and specifications are subject to change without
headphones of 32 ohms or more notice.
<Cassette deck section> • Dolby noise reduction manufactured under license from Dolby
Track format 4 tracks, 2 channels stereo Laboratories Licensing Corporation.
Frequency response CrO2 tape: 50 Hz – 16000 Hz "DOLBY" and the double-D symbol are trademarks of Dolby
Normal tape: 50 Hz – 15000 Hz Laboratories Licensing Corporation.
Signal to noise ratio 60dB (Dolby B NR ON, CrO2 tape
peak level) • The word "BBE"and the "BBE symbol" are trademarks of BBE
Recording system AC bias Sound, Inc.
Heads Deck 1: Playback head x 1 Under license from BBE Sound,Inc.
Deck 2: Recording/Playback head
x 1, erase head x 1

–2–
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING

This set employs laser. Therefore, be sure to follow carefully CAUTION

the instructions below when servicing. Use of controls or adjustments or performance of proce-
dures other than those specified herin may result in
WARNING!! hazardous radiation exposure.
WHEN SERVICING, DO NOT APPROACH THE LASER
EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS ATTENTION
NECESSARY TO CONFIRM LASER BEAM EMISSION. L’utillisation de commandes, réglages ou procédures
BE SURE TO OBSERVE FROM A DISTANCE OF MORE autres que ceux spécifiés peut entraîner une dangereuse
THAN 30cm FROM THE SURFACE OF THE OBJEC- exposition aux radiations.
TIVE LENS ON THE OPTICAL PICK-UP BLOCK.
ADVARSEL
s Caution: Invisible laser radiation when Usynlig laserståling ved åbning, når sikkerhedsafbrydereer
open and interlocks defeated avoid ude af funktion. Undgå udsættelse for stråling.
exposure to beam.
s Advarsel: Usynlig laserståling ved åbning, This Compact Disc player is classified as a CLASS 1
når sikkerhedsafbrydere er ude af funktion.
LASER product.
Undgå udsættelse for stråling.
The CLASS 1 LASER PRODUCT label is located on the
rear exterior.

VAROITUS!
Laiteen Käyttäminen muulla kuin tässä käyttöohjeessa
mainitulla tavalla saataa altistaa käyt-täjän
turvallisuusluokan 1 ylittävälle näkymättömälle
lasersäteilylle. CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
VARNING! LUOKAN 1 LASER LAITE
Om apparaten används på annat sätt än vad som KLASS 1 LASER APPARAT
specificeras i denna bruksanvising, kan användaren
utsättas för osynling laserstrålning, som överskrider
gränsen för laserklass 1.

Precaution to replace Optical block

PICK-UP Assy P.C.B
(KSS-213F)
Body or clothes electrostatic potential could
ruin laser diode in the optical block. Be sure
ground body and workbench, and use care the
clothes do not touch the diode.

1) After the connection, remove solder shown in

right figure.

Solder

–3–
NOTE ON BEFORE STARTING REPAIR
1. Forced discharge of electrolytic capacitor of power supply block
When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is kept charged across
the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect
can occur.
In order to prevent the secondary trouble, perform the following measures before starting repair work.

Discharge procedure
MAIN C.B
1 Remove the AC power cord.
2 Connect a discharging resistor at an end of lead wire that D101
has clips at both ends. Connect the other end of the lead
wire to metal chassis.
3 Contact the other end of the discharging resistor to the 3 4
positive (+) side (+VH) of C101. (For two seconds) C101 C102
4 Contact the same end of the discharging resistor as step
3 to the negative (-) side (-VH) of C102 in the same way.
(For two seconds)
5 Check that voltage across C101 and C102 has decreased
to 1 V or less using a multimeter or an oscilloscope. 2 2

Select a discharging resistor referring to the following table. Fig-1

Charging voltage (V) Discharging
Rated power (W) Parts number
(C101, 102) resistor (Ω)
25-48 100 3 87-A00-247-090
49-140 220 5 87-A00-232-090

Note: The reference numbers (C101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the
reference numbers of the charging capacitors on schematic diagram before starting the discharging work.

2. Check items before exchanging the MICROCOMPUTER

Be sure to check the following items before exchanging the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming
that the MICROCOMPUTER is surely defective.

2-1. Regarding the HOLD terminal of the MICROCOMPUTER

When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly.
When this terminal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD
terminal before exchange.
When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any
abnormalities that triggers the abnormality detection circuit on the MAIN C. B. that sets the HOLD terminal to “L”.

• Good or no good judgement of the MICROCOMPUTER

1 Turn on the AC main power.
2 Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not.
3 When the HOLD terminal is “L” level, the abnormality detection circuit is judged to be working correctly and the
MICROCOMPUTER is judged to be good.

–4–
 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not.

2-2. Regarding reset

There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power
cord is re-inserted, or the software reset (pressing the STOP key + POWER key) is performed.
When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to
exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and check good or no
good of the MICROCOMPUTER.
1 Remove the AC power cord.
R
TE

FRONT C.B
PU
M
CO
RO

18 % VSS
IC

15
M

C113 MICRO-
COMPUTER
* VDD
C113
FRONT C.B
Short with tweezers.

Fig-2-2

2 Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers.
3 Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER is
good.

Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending
on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work.

2-3. Confirmation of soldering state of MICROCOMPUTER

Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the
MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself.

–5–
ELECTRICAL MAIN PARTS LIST

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
IC MAIN C.B

8A-NF3-635-010 C-IC,LC876580W-5P43 C3 87-012-368-080 C-CAP,S 0.1-50 F

87-A21-482-010 IC,RPM6938-H4 C4 87-012-368-080 C-CAP,S 0.1-50 F
87-A20-869-040 C-IC,M62449FP C21 87-016-035-090 CAP, E 6800-35 VR
87-A21-398-010 IC,STK490-110 C22 87-016-035-090 CAP, E 6800-35 VR
87-A20-355-010 IC,CXA1553P C25 87-010-990-080 CAP,E 33-100 SME<HASM>

87-A20-783-040 C-IC,BA7762AFS C25 87-016-285-080 CAP,E 47-100 SME<LHSM>

87-A21-577-040 C-IC,M61506FP C26 87-010-990-080 CAP,E 33-100 SME<HASM>
87-070-289-040 IC,BU 2092F C26 87-016-285-080 CAP,E 47-100 SME<LHSM>
87-A21-021-040 C-IC,BU2099FV C27 87-010-990-080 CAP,E 33-100 SME<HASM>
87-A21-018-040 C-IC,M65849BFP631D C27 87-016-285-080 CAP,E 47-100 SME<LHSM>

87-A21-452-030 C-IC,BD3876KS2 C28 87-010-990-080 CAP,E 33-100 SME<HASM>

87-A21-051-040 C-IC,BU9990-03FS C28 87-016-285-080 CAP,E 47-100 SME<LHSM>
87-A21-560-010 IC,LA1844L-A C31 87-010-263-080 CAP, ELECT 100-10V
87-070-127-110 IC,LC72131 D C32 87-010-197-080 CAP, CHIP 0.01 DM
87-020-454-010 IC,DN 6851 C34 87-010-247-080 CAP, ELECT 100-50V

C35 87-010-380-080 CAP, ELECT 47-16V

TRANSISTOR C36 87-010-381-080 CAP, ELECT 330-16V
C38 87-010-384-080 CAP, ELECT 100-25V
87-026-245-080 TR,DTC114ES C39 87-010-384-080 CAP, ELECT 100-25V
87-A30-217-010 TR,2SB1436(R) C40 87-010-190-080 S CHIP F 0.01
87-A30-198-080 TR,KTC3199GR
89-213-702-010 TR,2SB1370 (1.8W) C60 87-010-403-080 CAP, ELECT 3.3-50V
87-A30-218-080 TR,2SB1237(Q) C80 87-010-401-080 CAP, ELECT 1-50V
C81 87-010-374-080 CAP, ELECT 47-10V
87-A30-087-080 C-FET,2SK2158 C82 87-010-260-080 CAP, ELECT 47-25V
87-A30-086-040 C-TR,CSD1306E C104 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A30-076-080 C-TR,2SC3052F
87-A30-107-070 C-TR,CMBT5401 C105 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A30-074-080 C-TR,RT1P 141C C111 87-010-401-080 CAP, ELECT 1-50V
C112 87-010-401-080 CAP, ELECT 1-50V
87-A30-190-080 TR,CC5551 C115 87-010-401-080 CAP, ELECT 1-50V
87-A30-204-010 TR,2SD2439 C116 87-010-401-080 CAP, ELECT 1-50V
87-A30-205-010 TR,2SB1588
87-A30-106-040 C-TR,CMBT5551 C121 87-010-406-080 CAP, ELECT 22-50
87-A30-276-040 C-TR,DTA143EKA C122 87-010-406-080 CAP, ELECT 22-50
C151 87-010-405-080 CAP, ELECT 10-50V<HASM>
87-A30-063-080 C-TR,KRA104S C163 87-010-196-080 CHIP CAPACITOR,0.1-25
87-026-609-080 TR,KTA1266GR C171 87-012-368-080 C-CAP,S 0.1-50 F
87-A30-186-010 FET,2SK3053
87-A30-075-080 C-TR,2SA1235F C172 87-012-368-080 C-CAP,S 0.1-50 F
87-A30-329-080 TR,CD1585BC C173 87-012-368-080 C-CAP,S 0.1-50 F
C174 87-012-368-080 C-CAP,S 0.1-50 F
87-A30-318-080 TR,CSA952K C175 87-A11-572-080 C-CAP,S 0.015-50 K B
89-327-143-080 TR,2SC2714 (0.1W) C176 87-A11-572-080 C-CAP,S 0.015-50 K B
87-A30-072-080 C-TR,RT1P 144C
87-A30-234-080 TR,CSC4115BC C177 87-010-197-080 CAP, CHIP 0.01 DM
87-026-463-080 TR,2SA933S C178 87-010-197-080 CAP, CHIP 0.01 DM
C301 87-010-318-080 C-CAP,S 47P-50 CH
C302 87-010-318-080 C-CAP,S 47P-50 CH
DIODE C303 87-012-157-080 C-CAP,S 330P-50 CH

87-A40-673-090 DIODE,D10XB20 C304 87-012-157-080 C-CAP,S 330P-50 CH

87-017-447-010 DIODE,GBU4DL-6419 C305 87-012-157-080 C-CAP,S 330P-50 CH
87-A40-224-010 DIODE,GBU8DL C306 87-012-157-080 C-CAP,S 330P-50 CH
87-017-654-060 DIODE,GBU6JL6131 C307 87-010-196-080 CHIP CAPACITOR,0.1-25
87-A40-736-080 DIODE,1N4148M(SEM) C311 87-010-198-080 CAP, CHIP 0.022

87-A40-553-080 DIODE,1N4003 LES C312 87-010-198-080 CAP, CHIP 0.022

87-A40-781-080 ZENER,UZ36BSA C313 87-010-180-080 C-CER 1500P
87-070-274-080 DIODE,1N4003 SEM C314 87-010-180-080 C-CER 1500P
87-A40-768-080 ZENER,UZ16BSA C315 87-010-178-080 CHIP CAP 1000P
87-017-154-080 ZENER,HZS6C3L C316 87-010-178-080 CHIP CAP 1000P

87-A40-488-080 DIODE,1SS244 C317 87-A10-201-080 C-CAP,S0.33-16 KB

87-020-331-080 CHIP-DIODE,DAN202K C318 87-A10-201-080 C-CAP,S0.33-16 KB
87-A40-313-080 C-DIODE,MC 2840 C319 87-012-141-080 CHIP-CAPACITOR,0.22-16F
87-A40-270-080 C-DIODE,MC2838 C320 87-012-141-080 CHIP-CAPACITOR,0.22-16F
87-A40-751-080 ZENER,UZ6.2BSB C321 87-012-141-080 CHIP-CAPACITOR,0.22-16F

87-A40-747-080 ZENER,UZ5.1BSB C322 87-012-141-080 CHIP-CAPACITOR,0.22-16F

87-A40-646-010 DIODE,FMB-G16L C324 87-010-260-080 CAP, ELECT 47-25V
87-A40-764-080 ZENER,UZ10BSC C325 87-010-370-080 CAP,E 330-6.3 SME
87-A40-745-080 ZENER,UZ4.7BSA C327 87-010-404-080 CAP, ELECT 4.7-50V
87-A40-749-080 ZENER,UZ5.6BSB C328 87-010-404-080 CAP, ELECT 4.7-50V

87-017-149-080 ZENER,HZS6A2L C332 87-010-196-080 CHIP CAPACITOR,0.1-25

C335 87-010-401-080 CAP, ELECT 1-50V
C336 87-010-401-080 CAP, ELECT 1-50V

–6–
 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C337 87-010-196-080 CHIP CAPACITOR,0.1-25 C627 87-010-400-080 CAP, ELECT 0.47-50V
C339 87-010-196-080 CHIP CAPACITOR,0.1-25 C628 87-010-400-080 CAP, ELECT 0.47-50V
C340 87-010-196-080 CHIP CAPACITOR,0.1-25 C629 87-010-992-080 C-CAP,S 0.047-25 B
C351 87-012-140-080 CAP 470P C630 87-010-383-080 CAP, ELECT 33-25V
C352 87-012-140-080 CAP 470P C631 87-010-185-080 C-CAP,S 3900P-50 B

C354 87-010-175-080 CAP 560P C632 87-010-185-080 C-CAP,S 3900P-50 B

C355 87-012-349-080 C-CAP,S 1000P-50 CH C634 87-010-196-080 CHIP CAPACITOR,0.1-25
C356 87-010-260-080 CAP, ELECT 47-25V C635 87-A10-307-080 CAP,M 0.1-50 J
C357 87-010-197-080 CAP, CHIP 0.01 DM C636 87-A10-307-080 CAP,M 0.1-50 J
C358 87-010-183-080 C-CAP,S 2700P-50 B C637 87-A10-307-080 CAP,M 0.1-50 J

C359 87-010-183-080 C-CAP,S 2700P-50 B C638 87-A10-307-080 CAP,M 0.1-50 J

C360 87-010-183-080 C-CAP,S 2700P-50 B C639 87-010-405-080 CAP, ELECT 10-50V
C370 87-010-196-080 CHIP CAPACITOR,0.1-25 C641 87-010-401-080 CAP, ELECT 1-50V
C371 87-010-175-080 CAP 560P C642 87-010-401-080 CAP, ELECT 1-50V
C372 87-010-175-080 CAP 560P C643 87-010-196-080 CHIP CAPACITOR,0.1-25

C373 87-010-179-080 CAP,CHIP S B1200P C644 87-010-401-080 CAP, ELECT 1-50V

C374 87-010-179-080 CAP,CHIP S B1200P C671 87-010-322-080 C-CAP,S 100P-50 CH
C375 87-010-545-080 CAP, ELECT 0.22-50V C672 87-010-322-080 C-CAP,S 100P-50 CH
C376 87-010-545-080 CAP, ELECT 0.22-50V C673 87-010-197-080 CAP, CHIP 0.01 DM
C378 87-010-196-080 CHIP CAPACITOR,0.1-25 C675 87-010-196-080 CHIP CAPACITOR,0.1-25

C381 87-010-197-080 CAP, CHIP 0.01 DM C679 87-010-196-080 CHIP CAPACITOR,0.1-25

C382 87-010-318-080 C-CAP,S 47P-50 CH C680 87-010-197-080 CAP, CHIP 0.01 DM
C383 87-010-197-080 CAP, CHIP 0.01 DM C682 87-010-196-080 CHIP CAPACITOR,0.1-25
C384 87-010-402-080 CAP, ELECT 2.2-50V C771 87-010-263-080 CAP, ELECT 100-10V
C385 87-010-184-080 CHIP CAPACITOR 3300P(K) C772 87-010-197-080 CAP, CHIP 0.01 DM

C386 87-010-196-080 CHIP CAPACITOR,0.1-25 C773 87-010-184-080 CHIP CAPACITOR 3300P(K)

C388 87-012-156-080 C-CAP,S 220P-50 CH C774 87-010-184-080 CHIP CAPACITOR 3300P(K)
C501 87-010-263-080 CAP, ELECT 100-10V C782 87-010-197-080 CAP, CHIP 0.01 DM
C502 87-010-196-080 CHIP CAPACITOR,0.1-25 C783 87-010-197-080 CAP, CHIP 0.01 DM
C503 87-016-460-080 C-CAP,S 0.22-16 B C784 87-010-197-080 CAP, CHIP 0.01 DM

C504 87-016-460-080 C-CAP,S 0.22-16 B C785 87-010-197-080 CAP, CHIP 0.01 DM

C505 87-012-141-080 CHIP-CAPACITOR,0.22-16F C786 87-010-197-080 CAP, CHIP 0.01 DM
C506 87-010-184-080 CHIP CAPACITOR 3300P(K) C788 87-010-149-080 C-CAP,S 5P-50 CH
C507 87-A11-550-080 C-CAP,S 820P-50 K B C789 87-012-365-080 C-CAP,S 0.027-25VBK
C508 87-016-669-080 C-CAP,S 0.1-25 K B C790 87-012-365-080 C-CAP,S 0.027-25VBK

C509 87-016-669-080 C-CAP,S 0.1-25 K B C791 87-010-196-080 CHIP CAPACITOR,0.1-25

C510 87-010-184-080 CHIP CAPACITOR 3300P(K) C792 87-010-197-080 CAP, CHIP 0.01 DM
C511 87-A11-550-080 C-CAP,S 820P-50 K B C793 87-010-404-080 CAP, ELECT 4.7-50V
C512 87-016-460-080 C-CAP,S 0.22-16 B C795 87-010-197-080 CAP, CHIP 0.01 DM
C513 87-010-544-080 CAP, ELECT 0.1-50V C796 87-010-197-080 CAP, CHIP 0.01 DM

C514 87-010-374-080 CAP, ELECT 47-10V C797 87-010-405-080 CAP, ELECT 10-50V
C515 87-010-401-080 CAP, ELECT 1-50V C798 87-010-197-080 CAP, CHIP 0.01 DM
C516 87-010-401-080 CAP, ELECT 1-50V C799 87-010-407-080 CAP, ELECT 33-50V
C517 87-010-183-080 C-CAP,S 2700P-50 B C800 87-012-369-080 C-CAP,S 0.047-50F
C518 87-010-183-080 C-CAP,S 2700P-50 B C801 87-010-403-080 CAP, ELECT 3.3-50V

C531 87-010-560-080 CAP,E 10-50 GAS C802 87-012-369-080 C-CAP,S 0.047-50F

C532 87-010-196-080 CHIP CAPACITOR,0.1-25 C803 87-010-198-080 CAP, CHIP 0.022
C533 87-010-196-080 CHIP CAPACITOR,0.1-25 C804 87-010-263-080 CAP, ELECT 100-10V
C534 87-012-156-080 C-CAP,S 220P-50 CH C807 87-010-400-080 CAP, ELECT 0.47-50V
C535 87-010-178-080 CHIP CAP 1000P C808 87-010-401-080 CAP, ELECT 1-50V

C536 87-010-196-080 CHIP CAPACITOR,0.1-25 C809 87-010-401-080 CAP, ELECT 1-50V

C538 87-010-318-080 C-CAP,S 47P-50 CH C810 87-010-196-080 CHIP CAPACITOR,0.1-25
C541 87-010-178-080 CHIP CAP 1000P C811 87-010-403-080 CAP, ELECT 3.3-50V
C603 87-010-318-080 C-CAP,S 47P-50 CH C812 87-010-403-080 CAP, ELECT 3.3-50V
C604 87-010-318-080 C-CAP,S 47P-50 CH C814 87-010-197-080 CAP, CHIP 0.01 DM

C605 87-010-318-080 C-CAP,S 47P-50 CH C815 87-010-400-080 CAP, ELECT 0.47-50V

C606 87-010-318-080 C-CAP,S 47P-50 CH C816 87-010-400-080 CAP, ELECT 0.47-50V
C611 87-010-956-080 CHIP-CAP,S 0.068-25B C819 87-010-179-080 CAP,CHIP S B1200P
C612 87-010-369-080 C-CAP,S 0.033-25 K B C820 87-010-179-080 CAP,CHIP S B1200P
C613 87-010-197-080 CAP, CHIP 0.01 DM C821 87-010-405-080 CAP, ELECT 10-50V

C614 87-016-669-080 C-CAP,S 0.1-25 K B C824 87-010-405-080 CAP, ELECT 10-50V

C616 87-010-180-080 C-CER 1500P C825 87-010-596-080 CAP, S 0.047-16
C617 87-010-198-080 CAP, CHIP 0.022 C959 87-010-196-080 CHIP CAPACITOR,0.1-25
C618 87-010-401-080 CAP, ELECT 1-50V C960 87-010-196-080 CHIP CAPACITOR,0.1-25
C619 87-010-263-080 CAP, ELECT 100-10V C961 87-010-152-080 C-CAP,S 8P-50 CH

C620 87-016-669-080 C-CAP,S 0.1-25 K B C963 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z

C621 87-010-197-080 CAP, CHIP 0.01 DM C971 87-010-381-080 CAP, ELECT 330-16V
C623 87-010-401-080 CAP, ELECT 1-50V C972 87-010-404-080 CAP, ELECT 4.7-50V
C624 87-010-401-080 CAP, ELECT 1-50V C973 87-010-197-080 CAP, CHIP 0.01 DM
C626 87-010-992-080 C-CAP,S 0.047-25 B C974 87-010-197-080 CAP, CHIP 0.01 DM

–7–
 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C979 87-010-322-080 C-CAP,S 100P-50 CH C110 87-010-196-080 CHIP CAPACITOR,0.1-25
C981 87-010-260-080 CAP, ELECT 47-25V C112 87-016-460-080 C-CAP,S 0.22-16 B
C982 87-010-196-080 CHIP CAPACITOR,0.1-25 C113 87-A10-189-040 CAP,E 220-10
C983 87-010-197-080 CAP, CHIP 0.01 DM C114 87-010-196-080 CHIP CAPACITOR,0.1-25
C984 87-010-197-080 CAP, CHIP 0.01 DM C115 87-010-198-080 CAP, CHIP 0.022

C987 87-010-197-080 CAP, CHIP 0.01 DM C116 87-010-493-040 CAP,E 0.47-50 GAS
C991 87-010-312-080 C-CAP,S 15P-50 CH C117 87-010-498-040 CAP,E 10-16 GAS
C992 87-010-312-080 C-CAP,S 15P-50 CH C118 87-010-194-080 CAP, CHIP 0.047
C993 87-010-178-080 CHIP CAP 1000P C119 87-A10-797-040 CAP,E 47-35 M 5L SRM
C995 87-010-178-080 CHIP CAP 1000P C120 87-015-699-040 CAP,E 10-50 7L

C997 87-010-196-080 CHIP CAPACITOR,0.1-25 C121 87-015-699-040 CAP,E 10-50 7L

C998 87-010-260-080 CAP, ELECT 47-25V C122 87-010-197-080 CAP, CHIP 0.01 DM
C999 87-A11-155-080 CAP,TC U 0.01-16 Z F C123 87-010-196-080 CHIP CAPACITOR,0.1-25
CN1 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3 C125 87-010-196-080 CHIP CAPACITOR,0.1-25
CN91 87-A60-619-010 CONN,2P V 2MM JMT C128 87-010-178-080 CHIP CAP 1000P

CN92 87-A60-619-010 CONN,2P V 2MM JMT C129 87-010-194-080 CAP, CHIP 0.047
CN101 87-A60-996-010 CONN,13P V BLK TAC-L13X-A3 C131 87-A10-189-040 CAP,E 220-10
CN301 87-A60-620-010 CONN,3P V 2MM JMT C132 87-A10-189-040 CAP,E 220-10
CN351 87-A60-625-010 CONN,8P V 2MM JMT C151 87-010-194-080 CAP, CHIP 0.047
CN601 87-099-719-010 CONN,30P TYK-B(X) C192 87-015-785-080 CHIP CAPACITOR, 0.1FZ-25Z

CN602 87-A60-131-010 CONN,6P V FE C196 87-010-194-080 CAP, CHIP 0.047

CN605 87-099-568-010 CONN,11P TUC-P11P-B1 C197 87-010-194-080 CAP, CHIP 0.047
CNA1 8A-NF8-653-010 CONN ASSY,9P TID-A(480) C213 87-A10-189-040 CAP,E 220-10
CNA2 8A-NF3-640-110 CONN ASSY,3P (VM) ANF-3 C301 87-010-318-080 C-CAP,S 47P-50 CH
FB501 87-008-372-080 FILTER, EMI BL OIRNI C303 87-016-460-080 C-CAP,S 0.22-16 B

FFC302 88-906-481-110 FF-CABLE,6P 1.25 480MM C304 87-016-460-080 C-CAP,S 0.22-16 B

FFE831 A8-8ZA-190-030 8ZA-1 FEUNM C305 87-010-196-080 CHIP CAPACITOR,0.1-25
J102 87-A60-238-010 TERMINAL,SP 4P (MSC) C306 87-010-196-080 CHIP CAPACITOR,0.1-25
J103 87-A60-483-010 JACK,DIA6.3 BLK ST W/S KM C310 87-010-067-040 CAP,E 0.1-50 5L
J601 87-A60-885-010 JACK,PIN 6P R/W MSC C701 87-010-981-040 CAP,E 22-35 5L SRE

J831 87-A60-202-010 TERMINAL,ANT 4P MSP-154V-02 C801 87-012-156-080 C-CAP,S 220P-50 CH

L101 87-A50-610-010 COIL,1UH K(MDEC) C802 87-010-176-080 C-CAP,S 680P-50 SL
L102 87-A50-610-010 COIL,1UH K(MDEC) C803 87-010-187-080 CAP CHIP S5600P
L301 87-A50-049-010 COIL,TRAP 85K(COI) C804 87-010-213-080 C-CAP,S 0.015-50 B
L302 87-A50-049-010 COIL,TRAP 85K(COI) C805 87-010-197-080 CAP, CHIP 0.01 DM

L351 87-007-342-010 COIL,OSC 85K BIAS C806 87-010-071-040 CAP,E 1-50 M 5L SRE
L801 87-A50-608-010 COIL,FM DET-N(TOK) C807 87-010-197-080 CAP, CHIP 0.01 DM
L802 87-A91-551-010 FLTR,PCFJZH-450 L(TOK) C809 87-012-155-080 C-CAP 180P-50CH
L811 87-005-847-080 COIL,2.2UH(CECS) C810 87-010-264-040 CAP,E 100-10 5L
L821 87-A50-209-010 COIL,1POLE MPX(MIT) C811 87-010-244-040 CAP,E 22-16 5L

L822 87-A50-209-010 COIL,1POLE MPX(MIT) C812 87-016-044-040 CAP,E 100-16 GAS

L832 87-005-847-080 COIL,2.2UH(CECS) C821 87-010-196-080 CHIP CAPACITOR,0.1-25
L951 8A-NF8-667-010 COIL,AM PACK 4(TOK) C833 87-010-322-080 C-CAP,S 100P-50 CH
R161 87-A00-441-050 RES,270-1/2W J RP C901 87-012-157-080 C-CAP,S 330P-50 CH
R162 87-A00-441-050 RES,270-1/2W J RP C902 87-010-176-080 C-CAP,S 680P-50 SL

R163 87-A00-441-050 RES,270-1/2W J RP C903 87-010-176-080 C-CAP,S 680P-50 SL

R164 87-A00-441-050 RES,270-1/2W J RP C904 87-010-176-080 C-CAP,S 680P-50 SL
R790 87-010-197-080 CAP, CHIP 0.01 DM C905 87-010-176-080 C-CAP,S 680P-50 SL
R991 87-010-322-080 C-CAP,S 100P-50 CH C906 87-010-176-080 C-CAP,S 680P-50 SL
R993 87-010-322-080 C-CAP,S 100P-50 CH C907 87-010-176-080 C-CAP,S 680P-50 SL

R995 87-010-322-080 C-CAP,S 100P-50 CH C908 87-010-176-080 C-CAP,S 680P-50 SL

SFR301 87-024-355-080 SFR,33K DIA6 H C909 87-010-176-080 C-CAP,S 680P-50 SL
SFR302 87-024-355-080 SFR,33K DIA6 H C910 87-010-176-080 C-CAP,S 680P-50 SL
SFR303 87-024-355-080 SFR,33K DIA6 H C911 87-010-176-080 C-CAP,S 680P-50 SL
SFR304 87-024-355-080 SFR,33K DIA6 H C912 87-010-176-080 C-CAP,S 680P-50 SL

SFR305 87-024-356-080 SFR,47K DIA6 H C913 87-010-176-080 C-CAP,S 680P-50 SL

SFR306 87-024-356-080 SFR,47K DIA6 H C914 87-012-145-080 CAP, CHIP S 270P CH
SFR351 87-024-356-080 SFR,47K DIA6 H CN101 87-099-720-010 CONN,30P TYK-B(P)
SFR352 87-024-356-080 SFR,47K DIA6 H CN102 87-A60-054-010 CONN,14P V 9604S-14C
X991 87-A70-061-010 VIB,XTAL 4.500MHZ CSA-309 CN103 87-099-750-010 CONN,15P V 9604SC

CN601 87-A60-062-010 CONN,05P V 9604S-05C

DISPLAY C.B CN701 87-099-750-010 CONN,15P V 9604SC
FFC102 88-914-481-110 FF-CABLE,14P 1.25 480MM
C103 87-010-196-080 CHIP CAPACITOR,0.1-25 FFC104 88-915-161-110 FF-CABLE,15P 1.25
C104 87-010-313-080 CAP, CHIP 18P FFC601 88-905-081-110 FF-CABLE,5P 1.25
C105 87-010-322-080 C-CAP,S 100P-50 CH
C106 87-012-145-080 CAP, CHIP S 270P CH FFC701 88-915-161-110 FF-CABLE,15P 1.25
C107 87-012-157-080 C-CAP,S 330P-50 CH FL101 8A-NF3-613-010 FL,BJ752GK-ANF3
JW315 87-A90-896-080 F-BEAD, 035600STY7
C108 87-015-681-040 E/CAP 10-16 JW316 87-A90-896-080 F-BEAD, 035600STY7
C109 87-010-401-040 CAP,E 1-50 SME L101 87-A50-333-010 COIL,OSC 9.43MHZ

–8–
 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
L801 87-A50-093-010 COIL,CLOCK 5.76MHZ S213 87-A90-095-080 SW,TACT EVQ11G04M
L802 87-003-098-080 COIL,2.2UH S214 87-A90-095-080 SW,TACT EVQ11G04M
S215 87-A90-095-080 SW,TACT EVQ11G04M
S216 87-A90-095-080 SW,TACT EVQ11G04M
CD KEY C.B S217 87-A90-095-080 SW,TACT EVQ11G04M

CN301 87-A60-079-010 CONN,08P H 9604S-08F S221 87-A90-095-080 SW,TACT EVQ11G04M

FFC302 88-908-381-110 FF-CABLE,8P 1.25 S222 87-A90-095-080 SW,TACT EVQ11G04M
LED311 87-A40-380-180 LED,SEL6510C-TP5 GRN S223 87-A90-095-080 SW,TACT EVQ11G04M
LED312 87-A40-380-180 LED,SEL6510C-TP5 GRN S224 87-A90-095-080 SW,TACT EVQ11G04M
LED313 87-A40-380-180 LED,SEL6510C-TP5 GRN S225 87-A90-095-080 SW,TACT EVQ11G04M

LED314 87-A40-380-180 LED,SEL6510C-TP5 GRN S226 87-A90-095-080 SW,TACT EVQ11G04M

LED315 87-A40-380-180 LED,SEL6510C-TP5 GRN S227 87-A90-095-080 SW,TACT EVQ11G04M
S311 87-A90-095-080 SW,TACT EVQ11G04M S228 87-A90-095-080 SW,TACT EVQ11G04M
S312 87-A90-095-080 SW,TACT EVQ11G04M S229 87-A90-095-080 SW,TACT EVQ11G04M
S313 87-A90-095-080 SW,TACT EVQ11G04M S230 87-A90-095-080 SW,TACT EVQ11G04M

S314 87-A90-095-080 SW,TACT EVQ11G04M S231 87-A90-095-080 SW,TACT EVQ11G04M

S315 87-A90-095-080 SW,TACT EVQ11G04M S232 87-A90-095-080 SW,TACT EVQ11G04M
S316 87-A90-095-080 SW,TACT EVQ11G04M S241 87-A90-095-080 SW,TACT EVQ11G04M
S317 87-A90-095-080 SW,TACT EVQ11G04M S242 87-A90-095-080 SW,TACT EVQ11G04M
S243 87-A90-095-080 SW,TACT EVQ11G04M

CONTROL C.B S244 87-A90-095-080 SW,TACT EVQ11G04M

S245 87-A90-095-080 SW,TACT EVQ11G04M
C401 87-010-196-080 CHIP CAPACITOR,0.1-25 S246 87-A90-095-080 SW,TACT EVQ11G04M
C407 87-010-322-080 C-CAP,S 100P-50 CH S247 87-A90-095-080 SW,TACT EVQ11G04M
C410 87-010-196-080 CHIP CAPACITOR,0.1-25 S248 87-A90-095-080 SW,TACT EVQ11G04M
C417 87-010-322-080 C-CAP,S 100P-50 CH
C423 87-010-196-080 CHIP CAPACITOR,0.1-25 S249 87-A90-095-080 SW,TACT EVQ11G04M
S250 87-A90-095-080 SW,TACT EVQ11G04M
C424 87-010-196-080 CHIP CAPACITOR,0.1-25 S251 87-A90-095-080 SW,TACT EVQ11G04M
C501 87-010-178-080 CHIP CAP 1000P SW501 87-A91-739-010 SW,RTRY EC12E12404-25MM RT
C502 87-012-156-080 C-CAP,S 220P-50 CH
C531 87-010-196-080 CHIP CAPACITOR,0.1-25
C532 87-010-196-080 CHIP CAPACITOR,0.1-25 VOLUME C.B

CN104 87-099-750-010 CONN,15P V 9604SC C161 87-010-178-080 CHIP CAP 1000P

CN302 87-A60-059-010 CONN,08P V 9604S-08C C162 87-012-156-080 C-CAP,S 220P-50 CH
LED101 87-A40-317-080 LED,SLR-342VCT31 RED S511 87-A90-095-080 SW,TACT EVQ11G04M
LED421 87-A40-831-010 LED,SELU1E10CXM-LF70 BLUE-DEF S512 87-A90-095-080 SW,TACT EVQ11G04M
LED422 87-A40-831-010 LED,SELU1E10CXM-LF70 BLUE-DEF S513 87-A90-095-080 SW,TACT EVQ11G04M

LED440 87-A40-380-180 LED,SEL6510C-TP5 GRN S514 87-A90-095-080 SW,TACT EVQ11G04M

LED441 87-A40-380-180 LED,SEL6510C-TP5 GRN S515 87-A90-095-080 SW,TACT EVQ11G04M
LED442 87-A40-380-180 LED,SEL6510C-TP5 GRN SW101 87-A91-740-010 SW,RTRY EC12E24308-30MM
LED443 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED444 87-A40-380-180 LED,SEL6510C-TP5 GRN
MIC C.B
LED445 87-A40-380-180 LED,SEL6510C-TP5 GRN
LED446 87-A40-380-180 LED,SEL6510C-TP5 GRN C601 87-010-196-080 CHIP CAPACITOR,0.1-25
LED447 87-A40-380-180 LED,SEL6510C-TP5 GRN C602 87-010-186-080 CAP,CHIP 4700P
LED448 87-A40-380-180 LED,SEL6510C-TP5 GRN C603 87-010-112-040 CAP,E 100-16
LED449 87-A40-380-180 LED,SEL6510C-TP5 GRN C604 87-010-405-040 CAP,E 10-50
C605 87-010-546-040 CAP,E 0.33-50
LED451 87-A40-537-040 LED,SLR-56PT-T31-W
LED452 87-A40-537-040 LED,SLR-56PT-T31-W C606 87-010-320-080 CHIP CAP 68P
LED453 87-A40-537-040 LED,SLR-56PT-T31-W C608 87-012-157-080 C-CAP,S 330P-50 CH
LED454 87-A40-537-040 LED,SLR-56PT-T31-W C621 87-010-178-080 CHIP CAP 1000P
LED455 87-A40-537-040 LED,SLR-56PT-T31-W CN602 87-A60-082-010 CONN,05P H 9604S-05F
J601 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM
LED456 87-A40-537-040 LED,SLR-56PT-T31-W
LED461 87-A40-317-080 LED,SLR-342VCT31 RED J602 87-A61-242-010 JACK,6.3 BLK MONO W/SW V KM
LED462 87-A40-317-080 LED,SLR-342VCT31 RED L601 87-003-098-080 COIL,2.2UH
LED463 87-A40-317-080 LED,SLR-342VCT31 RED
LED464 87-A40-317-080 LED,SLR-342VCT31 RED
AMP C.B
LED465 87-A40-317-080 LED,SLR-342VCT31 RED
LED521 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF C101 87-010-188-080 CAP,CHIP 6800P
LED522 87-A40-678-010 LED,SELU1E10CXM BLUE-DEF C102 87-010-188-080 CAP,CHIP 6800P
S201 87-A90-095-080 SW,TACT EVQ11G04M C103 87-010-405-080 CAP, ELECT 10-50V
S202 87-A90-095-080 SW,TACT EVQ11G04M C104 87-010-405-080 CAP, ELECT 10-50V
C107 87-010-404-080 CAP, ELECT 4.7-50V
S203 87-A90-095-080 SW,TACT EVQ11G04M
S204 87-A90-095-080 SW,TACT EVQ11G04M C108 87-010-404-080 CAP, ELECT 4.7-50V
S205 87-A90-095-080 SW,TACT EVQ11G04M C111 87-010-322-080 C-CAP,S 100P-50 CH
S206 87-A90-095-080 SW,TACT EVQ11G04M C112 87-010-322-080 C-CAP,S 100P-50 CH
S207 87-A90-095-080 SW,TACT EVQ11G04M C113 87-A10-812-080 C-CAP,S 220P-200 J CH
C114 87-A10-812-080 C-CAP,S 220P-200 J CH
S208 87-A90-095-080 SW,TACT EVQ11G04M
S211 87-A90-095-080 SW,TACT EVQ11G04M C119 87-010-197-080 CAP, CHIP 0.01 DM
S212 87-A90-095-080 SW,TACT EVQ11G04M C120 87-010-197-080 CAP, CHIP 0.01 DM

–9–
 REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
C121 87-010-260-080 CAP, ELECT 47-25V C23 87-A10-231-090 CAP,E 3300-80
C122 87-010-260-080 CAP, ELECT 47-25V C24 87-A11-148-080 CAP,TC U 0.1-50 Z F
C173 87-010-186-080 CAP,CHIP 4700P C25 87-A11-148-080 CAP,TC U 0.1-50 Z F
C174 87-010-186-080 CAP,CHIP 4700P C27 87-A11-148-080 CAP,TC U 0.1-50 Z F
C205 87-010-187-080 CAP,CHIP S5600P C28 87-A11-148-080 CAP,TC U 0.1-50 Z F

C206 87-010-187-080 CAP,CHIP S5600P C29 87-A11-148-080 CAP,TC U 0.1-50 Z F

C207 87-010-403-080 CAP, ELECT 3.3-50V C30 87-A11-148-080 CAP,TC U 0.1-50 Z F
C208 87-010-403-080 CAP, ELECT 3.3-50V C31 87-A11-148-080 CAP,TC U 0.1-50 Z F
C209 87-010-184-080 CHIP CAPACITOR 3300P(K) C32 87-A11-148-080 CAP,TC U 0.1-50 Z F
C210 87-010-184-080 CHIP CAPACITOR 3300P(K) C33 87-A11-148-080 CAP,TC U 0.1-50 Z F

C211 87-010-401-080 CAP, ELECT 1-50V C34 87-A11-148-080 CAP,TC U 0.1-50 Z F

C212 87-010-401-080 CAP, ELECT 1-50V C35 87-A11-148-080 CAP,TC U 0.1-50 Z F
C215 87-012-156-080 C-CAP,S 220P-50 CH C36 87-A11-148-080 CAP,TC U 0.1-50 Z F
C216 87-012-156-080 C-CAP,S 220P-50 CH C37 87-A11-148-080 CAP,TC U 0.1-50 Z F
C217 87-010-260-080 CAP, ELECT 47-25V C38 87-A11-148-080 CAP,TC U 0.1-50 Z F

C218 87-010-260-080 CAP, ELECT 47-25V CN1 87-A61-110-010 CONN,9P V TID-A

C221 87-016-100-080 CAP, ELECT 10-50 M BP SME CN2 87-A61-109-010 CONN,7P V TID-A
C222 87-016-100-080 CAP, ELECT 10-50 M BP SME ! F101 87-035-459-010 FUSE,5A 250V
C223 87-010-197-080 CAP, CHIP 0.01 DM ! F102 87-035-459-010 FUSE,5A 250V
C224 87-010-197-080 CAP, CHIP 0.01 DM ! FB101 87-A90-562-010 F-BEAD,9.5-17.5.5-28.5 BRH

C249 87-012-368-080 C-CAP,S 0.1-50 F ! FC1 87-033-213-080 FUSE CLAMP,PFC5000

C251 87-010-993-080 C-CAP,S 0.056-25 B ! FC2 87-033-213-080 FUSE CLAMP,PFC5000
C252 87-010-196-080 CHIP CAPACITOR,0.1-25 ! FC3 87-033-213-080 FUSE CLAMP,PFC5000
C253 87-010-196-080 CHIP CAPACITOR,0.1-25 ! FC4 87-033-213-080 FUSE CLAMP,PFC5000
C254 87-010-993-080 C-CAP,S 0.056-25 B ! PR1 87-026-682-080 PROTECTOR,10A 60V491
!
C255 87-010-190-080 S CHIP F 0.01 PR2 87-026-682-080 PROTECTOR,10A 491 SERIES 60V
C256 87-010-190-080 S CHIP F 0.01 ! PR3 87-A90-195-080 PROTECTOR,7A 125V 49
C265 87-010-260-080 CAP,E 47-25V ! PR4 87-A90-195-080 PROTECTOR,7A 125V 49
C402 87-010-196-080 CHIP CAPACITOR,0.1-25 ! PR5 87-A90-195-080 PROTECTOR,7A 125V 49
C413 87-A10-119-080 CAP,E 10-100 REA ! PR6 87-A90-195-080 PROTECTOR,7A 125V 49

C414 87-A10-119-080 CAP,E 10-100 REA ! PR7 87-026-682-080 PROTECTOR,10A 491 SERIES 60V
CNA101 8A-NF8-652-010 CONN ASSY,7P TID-A(480) ! PR8 87-026-682-080 PROTECTOR,10A 491 SERIES 60V
CON101 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3 ! PT2 8A-NF8-673-010 PT,SUB ANF-8 (H)KAMI
CON102 87-A61-011-010 CONN,13P H BLK TAC-L13P-A3 ! PT101 8A-NF3-602-010 PT,LH EI105-60 ANF-3
J201 87-A61-148-010 JACK,PIN 4P R/W BLUE ! RY2 87-A91-300-010 RELAY,AC 12V-ALA2PF12

JW138 87-A90-896-080 F-BEAD, 035600STY7 ! S1 87-A90-165-010 SW,SL 1-2-3 SWS2301

JW944 87-A90-896-080 F-BEAD, 035600STY7 ! T1 87-A60-317-010 TERMINAL, 1P MSC
L251 87-A50-610-010 COIL,1UH K(MDEC) ! T2 87-A60-317-010 TERMINAL, 1P MSC
L252 87-A50-610-010 COIL,1UH K(MDEC)
R161 87-A00-418-010 RES,M/F 0.15-3W J
VM C.B
R162 87-A00-418-010 RES,M/F 0.15-3W J
R165 87-A00-418-010 RES,M/F 0.15-3W J CNA3 87-049-919-010 CONN,3P EH V WHT
R166 87-A00-418-010 RES,M/F 0.15-3W J
R231 87-A00-669-080 RES,M/F 0.22-2W J RA
R232 87-A00-669-080 RES,M/F 0.22-2W J RA GEQ C.B

R243 87-A00-669-080 RES,M/F 0.22-2W J RA C201 87-010-402-080 CAP, ELECT 2.2-50V

R244 87-A00-669-080 RES,M/F 0.22-2W J RA C202 87-010-402-080 CAP, ELECT 2.2-50V
TH101 87-A91-042-080 C-THMS,100K 55001 C205 87-010-404-080 CAP, ELECT 4.7-50V
TH102 87-A91-042-080 C-THMS,100K 55001 C207 87-016-669-080 C-CAP,S 0.1-25 K B
WH101 87-A90-460-010 HLDR,WIRE 2.5-7P C208 87-016-669-080 C-CAP,S 0.1-25 K B

C209 87-016-460-080 C-CAP,S 0.22-16 B

PT C.B C210 87-016-460-080 C-CAP,S 0.22-16 B
C211 87-012-365-080 C-CAP,S 0.027-25VBK
C1 87-010-387-080 CAP,E 470-25 SME C212 87-012-365-080 C-CAP,S 0.027-25VBK
C4 87-A11-148-080 CAP,TC U 0.1-50 Z F C213 87-010-956-080 CHIP-CAP,S 0.068-25B
C5 87-A11-148-080 CAP,TC U 0.1-50 Z F
C6 87-010-917-000 CAP,E 3300-50 M SMG C214 87-010-956-080 CHIP-CAP,S 0.068-25B
C7 87-010-917-000 CAP,E 3300-50 M SMG C215 87-010-197-080 CAP, CHIP 0.01 DM
C216 87-010-197-080 CAP, CHIP 0.01 DM
C8 87-A11-148-080 CAP,TC U 0.1-50 Z F C217 87-010-198-080 CAP, CHIP 0.022
C9 87-A11-148-080 CAP,TC U 0.1-50 Z F C218 87-010-198-080 CAP, CHIP 0.022
C10 87-A11-148-080 CAP,TC U 0.1-50 Z F
C11 87-A11-148-080 CAP,TC U 0.1-50 Z F C219 87-010-183-080 C-CAP,S 2700P-50 B
C12 87-010-917-000 CAP,E 3300-50 M SMG C220 87-010-183-080 C-CAP,S 2700P-50 B
C221 87-010-188-080 CAP,CHIP 6800P
C13 87-010-917-000 CAP,E 3300-50 M SMG C222 87-010-188-080 CAP,CHIP 6800P
C16 87-010-403-040 CAP,E 3.3-50 SME C223 87-010-178-080 CHIP CAP 1000P
C18 87-A11-148-080 CAP,TC U 0.1-50 Z F
C19 87-A11-148-080 CAP,TC U 0.1-50 Z F C224 87-010-178-080 CHIP CAP 1000P
C20 87-A11-148-080 CAP,TC U 0.1-50 Z F C225 87-010-182-080 C-CAP,S 2200P-50 B
C226 87-010-182-080 C-CAP,S 2200P-50 B
C21 87-A11-148-080 CAP,TC U 0.1-50 Z F C227 87-010-112-080 CAP, ELECT 100-16V
C22 87-A10-231-090 CAP,E 3300-80 C228 87-010-196-080 CHIP CAPACITOR,0.1-25

– 10 –
 REF. NO. PART NO. KANRI DESCRIPTION
NO.
C229 87-010-322-080 C-CAP,S 100P-50 CH
C230 87-010-322-080 C-CAP,S 100P-50 CH
C231 87-010-322-080 C-CAP,S 100P-50 CH
CN201 87-A60-546-010 CONN,11P H GRY TUC-P11X-C1

DECK C.B

CN502 87-099-756-010 CONN,15P 9604S F

SFR1 87-024-581-010 SFR,3.3K DIA 6H
SOL1 82-ZM1-618-410 SOL ASSY,27
SOL2 82-ZM1-618-410 SOL ASSY,27
SW1 87-A90-248-010 SW,MICRO ESE11SH2CXQ

SW2 87-A90-248-010 SW,MICRO ESE11SH2CXQ

SW3 87-A90-248-010 SW,MICRO ESE11SH2CXQ
SW4 87-036-110-010 SW,MICRO SPPB62

HEAD-1 C.B

HEAD-2 C.B

CHIP RESISTOR PART CODE

Chip Resistor Part Coding

8 8
A
Figure
Resistor Code
Value of resistor
Chip resistor
Dimensions (mm) :A
Wattage Type Tolerance Symbol Form L W t Resistor Code : A
1/16W 1005 5% CJ 1.0 0.5 0.35 104
L
1/16W 1608 5% CJ t 1.6 0.8 0.45 108
1/10W 2125 5% CJ W 2 1.25 0.45 118
1/8W 3216 5% CJ 3.2 1.6 0.55 128

– 11 –
TRANSISTOR ILLUSTRATION

E C B E C B E C B E C B

KTA1266GR CD1585BC CC5551 DTC114ES 2SB1436

KTC3199GR CSC4115BC 2SA933S
CSA952K

G
S
B C E E C B G D S

2SB1370 2SB1237Q 2SK3053 2SK2158

2SB1588
2SD2439

B
E

2SA1235F CSD1306E
2SC2714 DTA143EKA
2SC3052F KRA104S
CMBT5551 RT1N141C
CMBT5401 RT1P144C

– 12 –
WIRING - 1 (MAIN)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 13 –
SCHEMATIC DIAGRAM – 1 (MAIN 1/3 / VM)

– 14 –
SCHEMATIC DIAGRAM – 2 (MAIN 2/3)

– 15 –
SCHEMATIC DIAGRAM – 3 (MAIN 3/3 / HEAD-1 / HEAD-2)

– 16 –
WIRING - 2 (DISPLAY / CD KEY)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 17 –
SCHEMATIC DIAGRAM – 4 (DISPLAY / CD KEY / DECK)

– 18 –
WIRING - 3 (CONTROL \ VOLUME \ MIC)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 19 –
SCHEMATIC DIAGRAM – 5 (CONTROL / VOLUME / MIC)

– 20 –
WIRING - 4 (AMP)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 21 –
SCHEMATIC DIAGRAM – 6 (AMP)

– 22 –
WIRING - 5 (DECK / GEQ / HEAD-1 / HEAD-2)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 23 –
SCHEMATIC DIAGRAM – 7 (GEQ)

– 24 –
WIRING - 6 (PT / VM)
32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

– 25 –
SCHEMATIC DIAGRAM – 8 (PT)

– 26 –
IC BLOCK DIAGRAM

IC, BU2099FV

IC, M62449FP

– 27 –
IC, BU2092F

IC, M65849BFP631D

– 28 –
IC, BA7762AFS

IC, CXA1553P

– 29 –
IC, BD3876KS

IC, LC72131D

– 30 –
IC, LA1844L-A

IC, BU9990-03FS IC, M61506FP

– 31 –
FL (BJ752GK-ANF3) GRID ASSIGNMENT AND ANODE CONNECTION
GRID ASSIGNMENT

– 32 –
ANODE CONNECTION

– 33 –
IC DESCRIPTION
IC, LC876580W-5P43

Pin No. Pin Name I/O Description

1 CLK O Common serial CLOCK output.
2 DATA O Common Serial DATA output.
3 STB O Common serial STROBE output.
4 CS-RHYTHM O Rhythm IC chip select output.
5 GEQ-CE O GEQ IC chip enable output.
6 HP-MUTE I Headphone plug-in detect input. (Output "L" at HOLD)
7 O-POWER O System power ON/OFF output. (Active "H")
8 PLL-CE O Tuner PLL IC chip enable output.
9 O-MUTE O System mute ON/OFF output.
10 I-MIC I Auto-VF MIC level special A/D input. (Output "L" at HOLD)
11 RESET I Reset input.
12 VOL-JOG I Main volume JOG rotary encoder A/D input.
13 MULTI-JOG I MULTI JOG rotary encoder A/D input.
14 VSS1 – Connected to GND.
15 CF 1
– 9.43MHz oscillator circuit.
16 CF2
17 VDD1 – Power supply.
18 HOLD I Power supply voltage detect A/D input.
19 ~ 22 KEY 1 ~ 4 I KEY 1 ~ 4 A/D input. (Output "L" at HOLD)
23 I-CDSW I CD mechanism SW A/D input. (Output "L" at HOLD)
24 I-DISH I CD turntable photo sensor A/D input. (Output "L" at HOLD)
25 I-SPEANA I SPEANA level A/D input. (Output "L" at HOLD)
26 I-RDSCLK/I-WRQ I TUNER RDS IC CLK (INT2) input / CD WRQ input. (Output "L" at HOLD&INI)
27 I-TU-SIG/MS I Tuner tuning signal level A/D input / Deck MS SENS. (Output "L" at HOLD)
28 I-TMBASE I Timebase clock (8Hz) input. (Output "L" at HOLD)
29 I-RMC I Remote control signal input. Active: "L". (Output "L" at HOLD)
30 ~ 42 G13 ~ G1 O FL grid G13 ~ G1 output.
43 ~ 45 P39 ~ P37 O FL segment P39 ~ P37 output.
46 VDD3 – Power supply.
47 P36/SPEANA A O FL segment P36 output / SPEANA band select output (A) .
48 P35/SPEANA B O FL segment P35 output / SPEANA band select output (B) .
49 P34/SPEANA C O FL segment P34 output / SPEANA band select output (C).
50 P33 O FL segment P33 output.
51 VP – Power supply for FL.
52 ~ 59 P32 ~ P25 O FL segment P32~ P25 output.
FL segment P24 output / NO AC-DEMO at AC-IN diode input. (No store DEMO
60 P24/NO AC-DEMO I/O
mode.)
61 P23/CASINO-DEMO I/O FL segment P23 output / CASINO-DEMO select diode input.
62 P22/NO-ECO I/O FL segment P22 output / NO-ECO select input.
63 P21/NO-RHYTHM I/O FL segment P21 output / NO-RHYTHM select diode input.
64 P20/AC3-DPL I/O FL segment P20 output / AC3-DPL select diode input. (Not used.)

– 34 –
Pin No. Pin Name I/O Description
65 P19/K-CON I/O FL segement P19 output / K-CON select diode input.
66 P18/RDS I/O FL segement P18 output / RDS select diode input.
67 P17/FM1 I/O FL segment P17 output / FM1 select diode input.
68 P16/SW I/O FL segment P16 output / SW step initial diode input.
69 P15/LW I/O FL segment P15output / LW stereo select diode input.
70 P14/AM-10K I/O FL segment P14 output /AM-10K select diode input.
71 P13/AM-ST I/O FL segment P13 output / AM-ST select diode input.
72 VDD4 – Power supply.
73~76 P12~P9 O FL segment P12~P9 output.
77 P8/REA I/O FL segment P8 ouput / REC enable (A) switch input (active: "L").
78 P7/CST1 I/O FL segment P7 output / Cassette (1) switch.
79 P6/CAM1 I/O FL segment P6 output / CAM (1) switch input (active: "L").
80 P5/AUTO2 I/O FL segment P5 output / Auto stop reel (2) pulse input.
81 P4/AUTO1 I/O FL segment P4 output / Auto stop reel (1) pulse input.
82 P3/CAM2 I/O FL segment P3 output / CAM (2) switch input. (active:"L").
83 P2/REB I/O FL segment P2 output / REC enable (B) switch input. (active:"L").
84 P1/CST2 I/O FL segment P1 output / Cassette (2) switch input. (active:"L").
85 K-SCAN O Key scan output. (active:"L").
86 SOL1 O DECK (1) solenoid ON/OFF output.
87 SOL2 O DECK (2) solenoid ON/OFF output.
88 O-MOTOR O Deck motor ON/OFF output .
89 VSS2 – Connected to GND.
90 VDD2 – Power supply.
91 O–DISHREV O CD turn table dish reverse output.
92 O-DISHFWD O CD turn table dish forward output.
93 O-OPEN O CD tray open output.
94 O-CLOSE O CD tray close output.
95 IFC-TU/I-SQDATA I Tuner tune/IF count input (active: "L") / CD SUB-Q data input.
I-STEREO/I-DRF
96 I/O Tuner stereo detect input (active "L") / DRF input.
(O-CLK-VCD)
O-DATA(CD)/
97 I/O CD IC control data output / Tuner RDS data input.
I-RDS DATA
CD-CE/
98 I/O CD chip enable output /
IO BUSY (VCD)
99 CLK (CD) O CD IC control clock output.
100 STB(SHIFT) O Shift register strobe output.

– 35 –
ADJUSTMENT <TUNER/DECK/DISPLAY>

A MAIN C.B
12 14 7 6 7 3

SFR351 L802
SFR352 L801 L951
IC303 TP3

SFR305 IC801 R815

24
SFR302 (3/3) (1/3)
SFR306 TP2 TP4
SFR301
(CLK) 4
SFR304
TP1 FFE831
SFR303
(VT)
TP11
11 (LCH)
GND TP10 (RCH)
GND

TP8 (LCH)
TP9 (RCH)
IC601
3
5
6
7

15 14 13 12 11 10 9 8 1 2 4

B DISPLAY C.B

FL101

TP1
(K-SCAN)

IC101
TP2(GND)
L101

16

K DECK C.B DECK–1 P,DECK-2 R/P/E HEAD

SFR1

9 9
8
REV FWD

– 36 –
< TUNER SECTION > < DECK SECTION >

8. Tape Speed Adjustment (DECK 1, DECK 2)

1. Clock Frequency Check Settings : • Test tape : TTA–100(3kHz)
Settings : • Test point : TP6 (CLK) • Test point : TP9(Rch), TP10(Lch)
Method : Set to AM 1710kHz and check that the test point is • Adjustment location : SFR1
2160kHz ± 45Hz. Method : Play back the test tape and adjust SFR1 so that the
frequency counter reads 3000Hz ± 5Hz(FWD) and ±
2. AM VT Check 45Hz(REV) with respect to forward speed.
Settings : • Test point : TP3 (VT)
Method : Set to AM 1710kHz and AM 530kHz and check that the
test point is less than 8.5V(1710kHz) and more than 9. Head Azimuth Adjustment (DECK 1, DECK 2)
0.6V(530kHz) Settings : • Test tape : TTA–300 (315/10kHz)
• Test point : TP9(Rch), TP10(Lch)
3. AM Tracking Adjustment • Adjustment location : Head azimuth
Settings : • Test point : TP7(Lch), TP8(Rch) adjustment screw
• Adjustment location : Method : Play back the 10kHz signal of the test tape and adjust
L951(1/3)........................ 999kHz screw so that the output becomes maximum. Next,
Method : Set to AM 999kHz and adjust L951(1/3) so that the test perform on each FWD PLAY and REV PLAY mode.
point is max.
10. PB Frequency Response Check (DECK 1, DECK 2)
4. FM VT Check Settings : • Test tape : TTA–300 (315/10kHz)
Settings : • Test point : TP3 (VT) • Test point : TP9(Rch), TP10(Lch)
Method : Set to FM 108.0MHz and check that the test point is Method : Play back the 315Hz and 10kHz signals of the test tape
less than 8.0V. and check that the output ratio of the 10kHz signal with
Set to FM 87.5MHz and check that the test point is respect to that of the 315Hz signal is within 0 ± 2dB.
more than 0.5V.
11. PB Sensitivity Adjustment (DECK 1, DECK 2)
5. FM Tracking Check Settings : • Test tape : TTA–200 (400Hz)
Settings : • Test point : TP7(Lch), TP8(Rch) • Test point : TP9(Rch), TP10(Lch)
Method : Set to FM 98.0MHz and check that the test point is less • Adjustment location :
than 9.0dBµV. SFR301 (DECK 1, Lch)
SFR302 (DECK 1, Rch)
6. AM IF Adjustment SFR303 (DECK 2, Lch)
Settings : • Test point : TP7(Lch), TP8(Rch) SFR304 (DECK 2, Rch)
• Adjustment location : L802 Method : Play back the test tape and adjust SFRs so that the
• Input level : Variable output level of the test points become 245mV±10mV.
Method : Adjust L802 so that the output becomes max.

7. DC Balance / Mono Distortion Adjustment 12. REC/PB Frequency Response Adjustment (DECK 2)
Settings : • Test point : TP4, TP5 Settings : • Test tape : TTA–602 (Normal)
(DC Balance) • Test point : TP9(Rch), TP10(Lch)
TP7(Lch), TP8(Rch) • Input signal : 1kHz / 10kHz (LINE IN)
(Distortion) • Adjustment location :
• Adjustment location : L801 SFR351 (Lch)
• Input level : 60dBµV SFR352 (Rch)
Method : Set to FM 98.0MHz and adjust L801 so that the voltage Method : Apply a 1kHz signal and REC mode. Then adjust OSC
between TP4 and TP5 becomes 0V ± 0.04V. attenuator so that the output level at the test points
Next, check that the distortion is less than 1.3% becomes 12.5mV. Record and play back the 1kHz and
10kHz signals and adjust SFRs so that the output level
of the 10kHz signals becomes 0dB ± 0.5dB with respect
to that of the 1kHz signal.

13. REC/PB Frequency response Check (DECK 2)

Settings : • Test tape : TTA-615 (CrO2)
• Test point : TP9(Rch), TP10(Lch)
• Input signal : 1kHz/10kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 12.5mV. Record and play back the 1kHz and
10kHz signals and check that the output is 0dB ± 2dB.

– 37 –
14. REC/PB Sensitivity Adjustment (DECK 2)
Settings : • Test tape : TTA–602 (Normal)
• Test point : TP9(Rch), TP10(Lch)
• Input signal : 1kHz (LINE IN)
• Adjustment location :
SFR305 (Lch)
SFR306 (Rch)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 125mV. Record the play back the 1kHz signal
and adjust SFRs so that the output level becomes 0dB ±
0.5dB

15. REC/PB Sensitivity Check (DECK 2)

Settings : • Test tape : TTA-615 (CrO2)
• Test point : TP9(Rch), TP10(Lch)
• Input signal : 1kHz (LINE IN)
Method : Apply a 1kHz signal and REC mode. Then adjust OSC
attenuator so that the output level at the test points
becomes 125mV. Record and play back the 1kHz signal
and check that the output is 0dB ± 1.5dB.

16. µ-CON OSC Adjustment

Settings : • Test point : TP1
• Adjustment location : L101
Method : Insert AC plug with pressing TUNER function key.
Adjust L101 so that the frequency across the test
point is 208.8Hz ± 0.2Hz.

– 38 –
MECHANICAL EXPLODED VIEW 1 / 1

– 39 –
MECHANICAL PARTS LIST 1 / 1

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 88-NF3-090-010 RING,FOOT 46 8A-NF3-208-010 HLDR,CHAS L
2 8A-NF3-042-010 PANEL ASSY,TRAY 47 87-NF4-221-010 HLDR,CABLE
3 8A-NF3-029-010 BOX,CASS R 48 87-A91-423-010 FAN,AD0612DS-D7OGL
4 8A-NF3-040-010 PANEL,CASS R ! 49 87-A80-148-010 AC CORD ASSY,E BLK
5 8A-NF3-059-010 WINDOW,CASS R 50 87-085-185-010 BUSHING, AC CORD (E)

6 8A-NF3-039-010 PANEL,CASS L 51 8A-NF3-209-010 HLDR,CHAS R

7 8A-NF3-058-010 WINDOW,CASS L 52 8A-NF3-211-010 HLDR,SIDE R
8 8A-NF3-028-010 BOX,CASS L 53 8A-NF3-229-010 HLDR,BRACKET
9 8A-NF3-090-010 REFLECTOR,CASS L 54 8Z-NF3-210-010 GUIDE,FL
10 81-532-080-010 LABEL, CASS. COMPT 55 8A-NF3-212-010 HLDR,REAR

11 8A-NF3-091-010 REFLECTOR,CASS R 56 84-ZG1-245-210 CAP,OPTICAL

12 8A-NF3-048-010 PANEL,REFLECTOR- CD 57 8A-NF3-026-010 CABI,BOTTOM
13 8A-NF3-049-010 PANEL,KEY-CD 58 8Z-NF3-048-010 COVER, BOTTOM
14 8A-NF3-047-010 PANEL,CD 59 82-NF5-219-010 SPR-T,EJECT 2 (SIN)
15 8A-NF3-071-010 KEY,CD 60 87-NF4-217-110 HLDR,LOCK 2

16 8A-NF3-089-010 REFLECTOR,CD 61 87-064-185-010 HLDR,WIRE

17 8A-NF3-203-010 GUIDE,LED-CD 62 8A-NF8-206-010 HLDR,PWB M
18 87-NF4-216-010 HLDR,LOCK 1 63 8A-NF3-221-010 HLDR,IC-VM
19 86-NF9-224-010 SPR-C,LOCK 64 8A-NF3-225-010 COVER, HLDR
20 82-NF5-229-010 PLATE,LOCK 65 8A-NF3-223-010 HLDR,FAN

21 87-NF8-220-010 DMPR,150 66 87-A91-711-010 FAN, 3110GL-B4W-B34-H02 -400MM

22 82-NF5-218-010 SPR-T,EJECT 1 (SIN) 67 8A-NF3-015-010 CABI,REAR HASM<HA>
23 8A-NF3-082-010 KNOB,RTRY JOG 67 8A-NF3-011-010 CABI,REAR LHSM<LH>
24 8A-NF3-087-010 REFLECTOR,JOG 68 8A-NF3-228-010 HLDR,PWB-PT
25 8A-NF3-077-010 RING,JOG H 69 8A-NF3-027-010 CABI,STEEL

26 8A-NF3-081-010 KNOB,RTRY VOL A 87-067-703-010 TAPPING SCREW, BVT2+3-10

27 8A-NF3-076-010 RING,VOL B 87-067-581-010 TAPPING SCREW, BVT2+3-15
28 8A-NF3-001-010 CABI,FR C 87-721-097-410 QT2+3-12 GLD
29 8A-NF3-034-010 PANEL,FR LH D 87-591-095-410 TAPPING SCREW, QIT+3-8 (GLD)
30 8A-NF3-051-010 WINDOW,DISP E 87-067-822-010 BVT2+3-20 W/O SLOT

31 8A-NF3-063-010 KEY ASSY,OPE F 87-067-689-010 TAPPING SCREW, BVTT+3-8

32 8A-NF3-073-010 KEY,REC U G 87-067-761-010 TAPPING SCREW, BVT2+3-10
33 8A-NF3-065-010 KEY,KARAOKE H 87-NF4-224-010 S-SCREW,IT3B+3-8 CU
34 8A-NF3-061-010 KEY,GEQ I 87-721-096-410 QT2+3-10 GLD
35 8A-NF3-067-010 KEY,BBE J 87-067-758-010 BVT2+3-12 W/O SLOT

36 8A-NF3-072-010 KEY,FUNC K 87-067-975-010 S-SCREW,IT+4-8

37 8A-NF3-088-010 REFLECTOR,FUNC L 87-067-641-010 UTT2+3-8(W/O SLOT)BL
38 8A-NF3-068-010 KEY,JOG M 87-067-579-010 TAPPING SCREW, BVT2+3-8
39 8A-NF3-062-010 KEY,DSP
40 8A-NF3-069-010 KEY,SPICE

41 8A-NF3-070-010 KEY,ECO
42 8A-NF3-201-010 GUIDE,LED-FUNC
43 8A-NF3-213-010 HLDR,HT-SINK L
44 8A-NF3-214-010 HLDR,HT-SINK R
45 8A-NF3-210-010 HLDR,SIDE L

COLOR NAME TABLE

Basic color symbol Color Basic color symbol Color Basic color symbol Color
B Black C Cream D Orange
G Green H Gray L Blue
LT Transparent Blue N Gold P Pink
R Red S Silver ST Titan Silver
T Brown V Violet W White
WT Transparent White Y Yellow YT Transparent Yellow
LM Metallic Blue LL Light Blue GT Transparent Green
LD Dark Blue DT Transparent Orange GM Metallic Green
YM Metallic Yellow DM Metallic Orange

– 40 –
TAPE MECHANISM EXPLODED VIEW 1 / 1

14 B
15
B

42 PH(DECK 1) 51
A RPH(DECK 2)
16 50 DECK C.B

52
CUSH-G,DIA3.7-8-3.2
12
13
CUSH-G,DIA3.7-8-3.2
17 18 50
11 10 49 A

44

41
9

7
B
47
43

3 35
48 41
19 E
2
CAPSTAN N 2.2-41.7
33 45
5 6
CAPSTAN N 2.2-41.5
A
20
4 46 31 34
SH,
HEAD 1 C.B(DECK 1) BELT D2 37
22 D
HEAD 2 C.B(DECK 2) D
C
36
(DECK 1) A 40
21 32 8

29 24 (DECK 1)
(DECK 2) 39
25 B

23 29 (DECK 2)
26 D 38

C
A 27

28 C 30
2ZM3MK2 PR4N
SH,1.63-3.2-0.5 SLT (BOTTOM SIDE)
2000/3/6 YPR4N
2ZM3MK2 PR4N,YPR4N
(TOP SIDE) 2000/3/6
– 41 –
TAPE MECHANISIM PARTS LIST 1 / 1

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 82-ZM3-301-510 CHAS ASSY,M2 36 82-ZM3-339-010 SHAFT,COUPLER N3(DECK 1)
2 82-ZM1-258-110 SPR-T,PINCH L 37 86-ZM1-206-010 BELT,MAIN L
3 82-ZM1-341-110 LVR ASSY,PINCH L2 38 82-ZM1-322-010 SPR-T,FR60
4 82-ZM1-333-010 PLATE,LINK 2 39 82-ZM1-220-210 GEAR,IDLER
5 82-ZM1-266-11K LVR,DIR 40 82-ZM3-616-010 RING MAGNET 4

6 82-ZM1-214-010 SPR-T,DIR 41 82-ZM1-216-31K GEAR,REEL

7 82-ZM1-206-81K CHAS,HEAD 42 87-A90-319-010 HEAD,PH HADKH2 FPC
8 82-ZM3-340-010 SH,BELT D2 42 87-A90-320-010 HEAD,RPH HADKH5 FPC
9 82-ZM1-269-210 SPR-T,BRG 43 82-ZM1-225-21K GEAR,FR
10 82-ZM1-219-110 SPR-T,LINK 44 82-ZM1-226-010 GEAR,REW

11 82-ZM1-210-110 GEAR,H T 45 82-ZM3-333-310 SLIP DISK ASSY 2

12 82-ZM1-213-010 SPR-T,HEAD 46 82-ZM1-338-010 BELT FR4
13 82-ZM1-207-610 GUIDE,TAPE 47 82-ZM1-349-110 FLY-WHL,R W(DECK 2)
14 86-ZM4-206-010 S-SCREW,AZIMUTH 47 82-ZM3-338-110 FLY-WHL,R3 W(DECK 1)
15 82-ZM1-314-110 PLATE,HEAD 48 82-ZM1-348-010 FLY-WHL,L W(DECK 2)

16 82-ZM1-208-110 HLDR,HEAD 48 82-ZM1-348-010 FLY-WHL,L W(DECK 1)

17 82-ZM1-218-010 SPR-E,HB 49 82-ZM3-329-210 BELT,SBU R2
18 82-ZM1-263-110 LVR,EJECT L (DECK 1) 50 82-ZM1-245-210 HLDR,IC
18 82-ZM1-264-010 LVR,EJECT R (DECK 2) 51 87-045-347-010 MOT,SHU2L 70(M1)
19 82-ZM1-222-21K LVR,PLAY 52 82-ZM3-221-010 PULLEY,MOT 2M

20 82-ZM1-217-310 REEL TABLE 53 82-ZM1-288-010 SH,1.63-3.2-0.5 SLT

21 82-ZM1-244-510 SPR-C,BT 54 80-ZM6-243-010 SH,1.75-3.6-0.5 SLT
22 82-ZM1-285-310 SPR-C,BT L 55 82-ZM3-335-210 PULLEY,COUPLER M3(DECK 1)
23 82-ZM1-257-010 SPR-T,CAS 56 82-ZM3-337-010 BELT,SBU MOT 2
24 82-ZM1-241-310 LVR,MC A 85-ZM3-202-010 S-SCREW,TG

25 82-ZM1-242-010 LVR,CAS B 80-ZM6-207-010 V+1.6-7

26 82-ZM1-243-010 LVR,STOP C 82-ZM3-318-010 S-SCRW MOTOR M2
27 82-ZM1-344-110 LVR ASSY,PINCH R2 D 87-B10-043-010 W-P,0.99-4-0.25 SLT
28 82-ZM1-259-110 SPR-T,PINCH R E 82-ZM3-334-010 PW,2.16-6-0.4
29 82-ZM1-240-11K LVR,REC (DECK 2)

31 82-ZM1-255-310 SPR-E,LVR DIR

32 82-ZM3-305-01K GEAR,CAM M2
33 82-ZM1-227-21K LVR,TRIG
34 82-ZM3-306-11K LVR,FR M2
35 82-ZM1-265-110 SPR-E,TRIG

– 42 –
SPEAKER DISASSEMBLY INSTRUCTIONS

Type.1 Type.4
Insert a flat-bladed screwdriver into the position indicated by the TOOLS
arrows and remove the panel. Remove the screws of each speaker 1 Plastic head hammer
unit and then remove the speaker units.
2 (() flat head screwdriver
3 Cut chisel

1 2 3

How to Remove the PANEL, FR

Type.2
1. Insert the (() flat head screwdriver tip into the gap
Remove the grill frame and four pieces of rubber caps by pulling between the PANEL, FR and the PANEL, SPKR. Tap the
out with a flat-bladed screwdriver. Remove the screws from hole head of the (() flat head screwdriver with the plastic
where installed rubber caps. Insert a flat-bladed screwdriver into hammer head, and create the clearance as shown in Fig-1.
the position indicated by the arrows and remove the panel. Re-
move the screws of each speaker unit and then remove the speaker 2. Insert the cut chisel in the clearance, and tap the head of
units. the cut chisel with plastic hammer as shown in Fig-2, to
remove the PANEL, FR.

3. Place the speaker horizontally. Tap head of the cut chisel

with plastic hammer as shown in Fig-3, and remove the
PANEL, FR completely.

Type.3
Insert a flat-bladed screwdriver into the position indicated by the
arrows and remove the panel. Turn the speaker unit to counter-
clockwise direction while inserting a flat-bladed screwdriver into
one of the hollows around speaker unit, and then remove the speaker
unit. After replacing the speaker unit, install it turning to clockwise Fig-1 Fig-2
direction until "click" sound comes out.

Fig-3

How to Attach the PANEL, FR

Attach the PANEL, FR to the PANEL, SPKR. Tap the four
corners of the PANEL, FR with the plastic hammer to fit the
PANEL, FR into the PANEL, SPKR completely.

– 43 –
SPEAKER PARTS LIST SX-WNT99 <YLSL>

REF. NO. PART NO. KANRI DESCRIPTION REF. NO. PART NO. KANRI DESCRIPTION
NO. NO.
1 8A-NS3-001-010 PANEL,FR 11 88-NS5-610-010 CORD,SPKR
2 8A-NS3-002-010 PANEL,TW L 12 88-NS5-611-010 CORD,SPKR B/L
3 8A-NS3-003-010 PANEL,TW R 13 8A-NSJ-006-010 BADGE,AIWA S35
4 8A-NS3-006-010 PANEL,TOP 14 8A-NS3-014-010 CABI,TOP
5 8A-NS3-009-010 PROTECTOR,SQA 16 8A-NS3-004-010 PANEL,DUCT RING

6 8A-NS3-011-010 PROTECTOR,TWA 17 8A-NS3-005-010 PANEL,DUCT

7 8A-MS1-602-010 SPKR,W 200
8 8A-NS3-602-010 SPKR,M 100
9 8A-MS2-605-110 SPKR,TW 60
10 88-NSK-610-010 SPKR,CERAMIC ASSY

ACCESORIES / PACKAGE LIST

REF. NO. PART NO. KANRI DESCRIPTION

NO.
1 8A-NF3-902-010 IB,LH (ESP) M<LH>
1 8A-NF3-907-010 IB,HA (S) NEA-ARG<HA>
2 87-006-225-010 AM LOOP ANT NC2
3 87-043-115-010 ANT,FEEDER FM
4 8Z-NF5-702-010 RC UNIT,RC-ZASO4

– 44 –
 2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
9620450 0251431 Printed in Singapore