HamMag - Noise Measurement

HAM-MAG
November 2009
F5SLD's Free HAM Magazine 100% HAM RADIO
NOISE
MEASUREMENT
Ma k e y o u r Q S L c a r d MF & H F A n te n n a
T h e No i se,
measu remen t
[ H O ME B R E W ] [ CATEGORIES ] DX Calendar 22
D I Y Patch Box 4 POST IT ! 3

H a l l o f F a me 34
Try a mobile Station 8

Comic's HAM 35
Making QSL Card 6
Noise measurement 9
[ HISTORY ]
DX NE W S 20
A hundred year of
amateur radio (part.2) 28
[ ANT E NNA ]
MF & HF receiving
A nt enna 32
[ HAMMAG N.10 November 2009 ]

B uy s w
P O S T- I T ! e e ti e s
f o
Hallowr
e e n.
Th e b reaki n g N ews
Four Radio Amateurs Killed in Plane Crash En Route to

CQWW Phone Contest (Oct 21, 2009 [REVISED Oct 22, 2009
11:05 ET]) Just after takeoff around 6:30 AM on Wednesday,
October 21 a twinengine plane carrying four Amateur Radio
operators crashed into the woods, only 250 yards off the end of
the runway in Jedburg, South Carolina, about 20 miles northwest
of Charleston. The plane piloted and owned by Peter Radding,
W2GJ carried Ed Steeble, K3IXD, Dallas Carter, W3PP, and
Randy Hargenrader, K4QO. The four men were on their way to
the Bahamas to operate in this weekend's CQ World Wide Phone
Contest as C6APR, competing in the Multi/2 category. (Tnx ARRL)
GB7OK DStar gateway is now live

The long awaited DStar gateway for GB7OK is now live.
I would like to thank all who have assisted me with this project Darren Storer G7LWT from the UK D
Star Interconnect Team for installing G2 Software and spending many days commissioning the
gateway, also technical support of Justin Johnson G0KSC installing and configuring Centos operating
system on the server.
Also not forgetting Martin Maynard G8CIX for contacting me in the first place to use GB7OK for
Amateur Radio Station live from the Plinth in Trafalgar Square, (One & Other Live Artwork) which gave
me the push to continue with this longawaited project and the support I received from Ian Lockyer
M3INL (Marketing Manager Icom UK).
Tony, G1HIG
Sunspot 1029 puts on a show

Since it emerged last weekend, newcycle sunspot 1029 has become the
biggest and most active sunspot of 2009. It is crackling with B and Cclass
solar flares and putting on a good show for amateur astronomers.
This one sunspot does not put an end to solar minimum, but it is a
remarkable break from the calm. Check : htttp://spaceweather.com
for images and updates
Keep tabs on ISS with an iPhone

A report on The Register describes new software for the iPhone/iPod Touch that provides real time
tracking of the International Space Station
The report says that on Friday NASA released an iPhone/iPod Touch application that delivers uptothe
minute Agency news, videos, and other scienctastic content from the convenience of your Apple device.
Read the full The Register report at
http://www.theregister.co.uk/2009/10/23/nasa_iphone_app/

DIY PATCH BOX
by Peter ZS2ABF
A practical Patch Box that works. The Patch box can be used to relay audio from one radio to another
without having to use the microphone held next to a loudspeaker.
I used an old Midland CB radio mike. This allows me to break in and talk or switch off the relayed signal
and just talk without having to changer plugs etc. The VU meter monitors the Audio into the output part
of the circuit, at the output of the step down transformer.
If you are recording sounds from a radio in a computer and you do not have enough audio output from
this box, then just reverse the step down transformer. The position shown works ok for my set up. The
meter, diode and, potty circuit are not necessary, but can be added as a “Brag” feature.
I am using this output into a Kenwood which has the Network type mic socket. You may have to modify
the output cable to attach a plug of the type to suit your personal equipment.
The two variable potties are shown with a + value and can be substituted for another suitable value
that works for you. It’s a nice easy to build project, and can be a useful gadget to have in your Shack.
73’s ZS2ABF
Photo of the finished BOX

CIRCUIT DIAGRAM – Patch box circuit

HomeBrew QSL Cards
By KA6KBC, Bill
I remember as a young amateur the excitement of going to the mailbox and finding a QSL card from an
earlier QSO. This is what it's all about. It reinforces the personal aspect of the hobby. I encourage you
to experiment with your photography and desktop publishing techniques to produce QSL cards you are
proud of. A QSL card is a specially designed postcard that hams exchange in the mail whenever they
make contact with one another for the first time. Hams exchange cards in friendship and to prove that
they actually made radio contact.
Each ham’s QSL card has a unique design that may include words and pictures about his or her family,
friends, and places that are special to them. The cards also include information about the ham’s call
sign, radio contact equipment, date, time and type of contact, and geographic location of the ham.
One of the best things about being a ham radio operator is the chance to talk to people on the other
side of town, the other side of the state or even the other side of the planet that you wouldn't have
otherwise met. Ham radio operators traditionally exchange QSL cards through the mail to confirm that
mutual contact has occurred. A custom QSL card is truly a collector's item for the people you contact.
Fortunately, with a little help from your computer and printer, they're easy and fun to make.
How to Make a Custom QSL Card:
From your PC:
There is nice software that can be down loaded – QSL Maker, developed by WB8RCR let’s you design
and print your own QSL cards, allowing to personalize background, by importing pictures or just filling
with a plain color, and let’s you personalize headings and address as well as your own callsign. It can
import ADIF log file for fields autofilling during the print process, or allow you to insert directly QSO
Data into a table. It runs on Windows, I've tested it on Windows XP, and is completely Free ! Works
great. You can make a very custom QSL Cards.
http://qslmaker.mints.org/
Sample Card:
[ HAMMAG N.10
N°35 November
15 octobre2009
2009] ]
OnLine Only:
The website RadioQTH offers a very nice service. You can use this web page to create QSL cards.
You don’t even need to get a login to use the service. The cards will be created in the form of a PDF
document that you can then print on lightweight card stock. The individual cards can then be cut out
and the information filled in and mailed to the intended recipient. You have the option of printing a single
QSL card or printing up to four cards per page. The cards are printed 5.5 inches wide by 3.5 inches
high. This is a standard size for a QSL card. It allows you to personalize background, by importing
pictures and you can also do some color selection. Less custom, but very easy to use and nothing to
download.
http://www.radioqth.net/qsl.aspx
Sample:
73’s – Bill – KA6KBC

http://billbrwn.tripod.com/id23.html
Note from F5SLD.

You can also have you QSL on line (with your log) in the website :
http://www.eqsl.cc/qslcard/Index.cfm
Sample :

NO SPACE LEFT ?
TRY A MOBILE STATION
B Y K 0HL
Hello,
I have a modest ham radio station installed in my pickup
truck, you and your readers may find it interesting. My
intention is to supply you some raw material; if you feel
the material has merit for your magazine, feel free to ask
for more information. I am supplying you essentially
teaser pictures, you may use them in any way you desire.
I can supply better photos if you need them.
This is not meant to be a step by step article on how to do
a mobile installation. I will be very brief, if you want more,
you will have to ask?
Background information:
My QTH is not amenable to installing a base station. If I am to participate in ham radio then it has to be
from my mobile.
Installing a ham radio station in a mobile is not an endeavor for the faint of heart. There are many
difficulties along the road to having a good working EFFECTIVE ham radio station in a mobile. I do not
want to discourage anyone from trying this, but, go in with both eyes open, and expect this to be
moderately costly.
Difficulties you should expect:
1) Getting adequate 12 DC through the firewall of your vehicle,

firewalls are crowded to the extreme, the surfaces available are
either at an acute angle and hard to drill, or access is blocked. One
of the key ingredients in a good EFFECTIVE mobile ham radio
station is an adequate supply of DC.
2) Mounting you antenna: Ground losses are your biggest problem. If you mount your antenna
properly, your ground losses will be low and your signal will be large. It’s your choice, mount your
antenna in the proper location, or suffer the loss of performance that is a certainty with a poor location.
Physically mounting the antenna to withstand a driving speed of 80 MPH into a 25 MPH headwind,
along with the normal pitching and heaving of the vehicle as it traverses the roadway is a serious
problem. You need a strong mount. NO MAG MOUNTS! If you cannot bring yourself to drill holes in
your vehicle, give up now take up playing cards.
3) Common mode (CM): The nemesis of mobile

installations. Plan on having CM, ferrite beads and lots of
them. Do not spare the beads.
4) Noise: Electronic nose of a dozen varieties will test your

patience to the limit. EXPECT IT, expect it to be very hard to
eliminate.
There, that is my teaser.
73, K0HL

NOISE: Measurement and Generation
By Paul Wade N1BWT
Introduction
As anyone who has listened to a receiver suspects, everything in the universe

generates noise. In communications, the goal is to maximize the desired signal in
relation to the undesired noise we hear. In order to accomplish this goal, it would be helpful to
understand where noise originates, how much our own receiver adds to the noise we hear, and how to
minimize it.
It is difficult to improve something unless we are able to measure it. Measurement of noise in receivers
does not seem to be clearly understood by many amateurs, so I will attempt to explain the concepts
and clarify the techniques, and to descrive the standard “measure of merit” for receiver noise
performance: “noise figure.” Most important, I will describe how to build your own noise generator for
noise figure measurements. A number of equations are included, but only a few need be used to
perform noise figure measurements. The rest are included to as an aid to understanding, with, I hope,
enough explanatory text for everyone.
Noise
The most pervasive source of noise is thermal noise, due to the motion of thermally agitated free
electrons in a conductor. Since everything in the universe is at some temperature above absolute zero,
every conductor must generate noise. Every resistor (and all conductors have resistance) generates an
rms noise voltage:
e= V4kTRB
Where R is the resistance, T is the absolute temperature in degrees K, B is the bandwidth in Hertz, and
k is Boltzmann’s constant, 1.38 x 1023 joules / K.
Converting to power, e2 /R , and adjusting for the Gaussian distribution of noise voltage, the noise
power generated by the resistor is:
Pn = kTB (watts)
Which is independent of the resistance. Thus, all resistors at the same temperature generate the same
noise power. The noise is white noise, meaning that the power density does not vary with frequency, but
always has a power density of kT watts/Hz. More important is that the noise power is directly
proportional to absolute temperature T, since k is a constant. At the nominal ambient temperature of
290 K, we can calculate this power; converted to dBm, we get the familiar 174 dBm/Hz. Just multiply
by the bandwidth in Hertz to get the available noise power at ambient temperature. The choice of 290 K
for ambient might seem a bit cool, since the equivalent 17° C or 62° F would be a rather cool room
temperature, but 290 makes all the calculations come out to even numbers.
The instantaneous noise voltage has a Gaussian distribution around the rms value. The gaussian
distribution has no limit on the peak amplitude, so at any instant the noise voltage may have any value
from infinity to +infinity. For design purposes, we can use a value that will not be exceeded more than
0.01% of the time. This voltage is 4 times the rms value, or 12 dB higher, so our system must be able to
handle peak powers 12 dB higher than the average noise power 1 to if we are to measure noise without
errors.

Signal to Noise Ratio
Now that we know the noise power in a given bandwidth, we can easily calculate how much signal is
required to achieve a desired signal to noise ratio, S/N. For SSB, perhaps 10 dB S/N is required for
good communications; since ambient thermal noise in a 2.5 KHz bandwidth is 140 dBm, calculated as
follows:
Pn = kTB = 1.38 x 1023 x 290 x 2500 = 1.0 x 1017 watts

dBm = 10log ( Pn x 1000 ) [multiplying the power by 1000 to get milliwatts]
The signal power must be 10 dB larger, so minimum signal level of 130 dBm is required for a 10 dB
S/N. This represents the noise and signal power levels at the antenna. We are then faced with the task
of amplifying the signal without degrading the signal to noise ratio.
Noise Temperature
Any amplifier will add additional noise. The input noise Ni per unit bandwidth is kTg is amplified by gain
G to produce an output noise of kTgG. The additional noise, kTn is added to produce a total noise
output power No:
No = kTgG + kTn
To simplify future calculations, we pretend that the amplifier is noisefree but has an additional noise
generating resistor of temperature Te at the input, so that all sources of noise are inputs to the amplifier.
Then the output noise is:
No = kG ( Tg + Te )
And Te is the Noise Temperature of the excess noise contributed by the amplifier. The noise added by
an amplifier is then kGTe, which is the fictitious noise source at the input amplified by the amplifier gain.
Cascaded Amplifiers
If several amplifiers are cascaded, the output noise No of each becomes the input noise Tg to the next
stage, we can create a large equation for the total. After removing the original input noise term, we are
left with the added noise:
Nadded = (k Te1G1G2... GN) + (kTe2G2... GN) + ... + (kTeNGN)

Substituting in the total gain GT = (G1G2... GN) results in the total excess noise:
TeT = Te1 + Te2 /G1 + Te2 /G1G2 + ... + TeN /(G1G2... GN1)
With the noise of each succeeding stage reduced by the gain of all preceeding stages.
Clearly, if the gain of the first stage, G1, is large, then the noise contributions of the succeeding stages
are not significant. This is why we concentrate our efforts on improving the first amplifier or preamplifier.
Noise Figure
The noise figure of an amplifier is the logarithm of the ratio (so we can express it in dB) of the total
noise output of an amplifier with an input Tg of 290 K to the noise output of an equivalent noisefree
amplifier. A more useful definition is to calculate it from the excess temperature Te:
NF = 10log( 1 + Te /T0) (dB) @ T0 = 290 K
If the NF is known, then Te may be calculated after converting the NF to a ratio, F:
Te = ( F 1) T0
Typically, Te is specified for very low noise amplifiers, where the NF would be fraction of a dB, and NF is
used when it seems a more manageable number than thousands of K.

We know that any loss or attenuation in a system reduces the signal level. If attenuation also reduced
the noise level, then we could suppress thermal noise by adding attenuation. We know intuitively that
this can’t be true. The answer is that the attenuator or any lossy element has a physical temperature,
Tx, which contributes noise to the system while the input noise is being attenuated. The output noise
after a loss L (ratio) is:
Tg’ = Tg /L + [(L1)/L] Tx
If the source temperature Tg is higher than the attenuator temperature Tx , then the noise
contribution is the familiar result found by simply adding the loss in dB to the NF. However, for low
source temperatures the degradation can be much more dramatic. If we do a calculation for the affect
of 1 dB of loss ( L = 1.26 ) on a Tg of 25 K:
Tg’ = 25/1.26 + (0.26/1.26) x 290 = 80 K
The resultant Tg’ is 80 K, a 5 dB increase in noise power (or 5 dB degradation of signal to noise ratio).
Since noise power = kT and k is a constant, the increase is the ratio of the two temperatures 80/25, or
in dB, 10log( 80/25 ) = 5 dB.
Antenna Temperature
How can we have a source temperature much lower than ambient? If an antenna, assumed to be
lossless, is receiving signals from space, rather than the warm earth, then the background noise is
much lower. The background temperature of the universe has been measured as about 3.2 K. An
empirical number 2 for a 10 GHz antenna pointing into clear sky is about 6 K, since we must always
look through attenuation and temperature of the atmosphere. The figure will vary with frequency, but a
good EME antenna might have a Tg of around 20 K at UHF and higher frequencies.
A couple of examples of actual antennas3 might bring all of this together.
1. A 30 inch conventional dish at 10 GHz, with measured gain of 36.4 dBi and efficiency of 64%. The
estimated spillover efficiency is 87% for a 10 dB illumination taper. With the dish pointing at a high
elevation as shown in Figure 1, perhaps half of the spillover is illuminating earth at 290 K, which adds
an estimated 19 K to the 6 K of sky noise, for a total of 25 K. In a 500 Hz bandwidth, the noise output is
157.6 dBm.
2. An 18 inch DSS offsetfed dish at 10 GHz, with measured gain of 32.0 dB and efficiency of 63%. The
spillover efficiency should be comparable, but with the offset dish pointing at a high elevation as shown
in Figure 2, far less of the spillover is illuminating warm earth. If we estimate 20%, then 8 K is added to
the 6 K of sky noise, for a total of 14 K. In a 500 Hz bandwidth, the noise output is 160 dBm.
Fig.1. Parabolic Dish Antenna Aimed at Satellite Fig.2. Offset Parabolic Dish Antenna Aimed at
Satellite

The larger conventional dish has 2.4 dB higher noise output, but 4.4 dB higher gain, so it should have
2.0 dB better signal to noise ratio than the smaller offset dish when both are pointing at high elevations.
However, the while the offset dish is easy to feed with low loss, it is convenient to feed the conventional
dish through a cable with 1 dB of loss. Referring back to our loss example above, the noise temperature
after this cable loss is 80 K. In a 500 Hz bandwidth, the noise output is now 152.6 dBm, 7.4 dB worse
than the offset dish. The convenience of the cable reduces the signal to noise ratio by 5 dB, making the
larger conventional dish 3 dB worse than the smaller offset dish. Is it any wonder that the DSS
dishes sprouting on rooftops everywhere are offsetfed?
If the dishes are pointed on the horizon for terrestrial operation, then the situation is much different. At
least half of each antenna pattern is illuminating warm earth, so we should expect the noise
temperature to be at least half of 290 K, or about 150 K. Adding 1 dB of loss increases the noise
temperature to 179 K, a 1 dB increase. At the higher noise temperatures, losses do not have a dramatic
effect on signal to noise ratio. In practice, the antenna temperature on the horizon may be even higher,
since the upper half of the pattern must take a much longer path through the warm atmosphere, which
adds noise just like any other loss.
Image Response
Most receiving systems use at least one frequency converting mixer which has two responses, the
desired frequency and an image frequency on the other side of the local oscillator. If the image
response is not filtered out, it will add additional noise to the mixer output. Since most preamps are
broadband enough to have significant gain (and thus, noise output) at the image frequency, the filter
must be placed between the preamp and the mixer. The total NF including image response is
calculated:
NF = 10log[ ( 1 + Te /T0)( 1 + Gimage/Gdesired) ]
assuming equal noise bandwidth for desired and image responses. Without any filtering,
Gimage = Gdesired so Gimage/Gdesired = 1
Doubling the noise figure which is the same as adding 3 dB. Thus, without any image rejection, the
overall noise figure is at least 3 dB regardless of the NF of the preamp. For the image to add less than
0.1 dB to the overall NF, a quick calculation shows that the gain at the image frequency must be at least
16 dB lower than at the operating frequency.
Noise Figure Measurement
So far we have dixcussed the sources of noise, and a figure of for evaluating the a receiving system’s
response to noise. How can we measure an actual receiver?
The noise figure of a receiver is determined by measuring its output with two different noise levels, Thot
and Tcold, applied at the input. The ratio of the two output levels is referred to as the “Yfactor”. Usually,
the ratio is determined from the difference in dB between the two output levels,
Ydb: Y(ratio) = log1(Ydb / 10)
Then the receiver Te may be calculated using Y(ratio) :
Te = (Thot YTcold ) / (Y1)
and converted to noise figure:
NF = 10log (1 + Te /T0) (dB) where T0 = 290 K
The two different noise levels may be generated separately, for instance by connecting resistors at two
different temperatures. Alternatively, we could use a device that can generate a calibrated amount of
noise when it is turned on. When such a device is turned off, it still generates noise from its internal
resistance at Tcold, the ambient temperature (290 K); usually this resistance is 50 ohms, to properly
terminate the transmission line which connects it to the receiver.When the noise generator is turned on,
it produces excess noise equivalent to a resistor at some higher temperature at Thot.

The noise produced by a noise source may be specified as the Excess Noise Ratio (ENRdB), the dB
difference between the cold and the equivalent hot temperature, or as the equivalent temperature of the
excess noise, Tex, which is used in place of Thot in the previous equation. If the ENR is specified, then
the calculation is:
NFdB = ENRdB 10log(Y(ratio) 1)
The terms Tex and ENR are used rather loosely; assume that a noise source specified in dB refers to
ENRdB, while a specification in degrees or K refers to Tex.
An automatic noise figure meter, sometimes called a PANFI ( for Precision Automatic Noise Figure
Meter), turns the noise source on and off at a rate of about 400 Hz and performs the above calculation
electronically. A wide bandwidth is required to detect enough noise to operate at this rate; a manual
measurement using a narrowband communications receiver would require the switching rate to be less
than one Hz, with some kind of electronic integration to properly average the gaussian noise.
Noise figure meters seem to be fairly common surplus items. The only one in current production, the HP
8970, measures both noise figure and gain, but commands a stiff price.
AIL (later AILTECH or Eaton) made several models; the model 2075 measures both NF and gain, while
other models are NF only. The model 75 (a whole series whose model numbers start with 75) shows up
frequently for anywhere from $7 to $400, typically $25 to $50 and performs well. Every VHFer I know
has one, with most of them waiting for a noise source to be usable. Earlier tube models, like the AIL 74
and the HP 340 and 342, have problems with drift and heat, but they can also do the job.
Another alternative is to build a noise figure meter5.
Using the Noise Figure Meter
I’ll describe the basic procedure using the Model 75; others are similar, but the more complex
instruments will require studying the instruction manual. Input to almost all noise figure meters is at 30
MHz, so a frequency converter is required (some instruments have internal frequency converters;
except for the HP 8970, I’d avoid using this feature). Most ham converters with a 28 MHz IF work fine,
unless the preamp being measured is so narrowband that a MHz or two changes the NF. The input is
fairly broadband, so LO leakage or any other stray signals can upset the measurement ¾ this
has been a source of frustration for many users. There are two solutions: a filter (30 MHz lowpass TVI
filters are often sufficient) or a tuned amplifier at 30 MHz. Since a fair amount of gain is required in front
of the noise figure meter, an amplifier is usually required anyway.
A noise source (which we will discuss in detail later) is connected to the rear of the instrument: a BNC
connector marked “DIODE GATE” provides +28 volts for a solidstate noise source, and high voltage
leads for a gas tube noise source are also available on many versions. The noise figure meter switches
the noise source on and off. The noise output coax connector of the noise source is connected to the
receiver input. The model 75 has four function pushbuttons: OFF, ON, AUTO, and CAL. The OFF and
ON positions are for manual measurements: OFF displays the detector output with the noise source
turned off, and ON displays the detector output with the noise source turned on. If all is working, there
should be more output in the ON position, and a step attenuator in the IF line may be used to determine
the change in output, or Yfactor, to sanitycheck our results. The knob marked “GAIN” is used to get
the meter reading to a desirable part of the scale in the OFF and ON positions only; it has no effect on
automatic measurements.
The AUTO position causes the instrument to turn the noise source on and off at about a 400 Hz rate
and to calculate the NF from the detected change in noise. The model 75 has a large green light near
the meter which indicates that the input level is high enough for proper operation ¾ add gain until the
light comes on. Then the meter should indicate a noise figure, but not a meaningful one, since we must
first set the ENRdB using the CAL position. The lower scale on the meter is marked for from 14.5 to
16.5 dB of ENR; adjust the “CAL ADJ” knob until the reading in the CAL position matches the ENR of
the noise source. If the ENR of your noise source is outside the marked range, read the section below
on homebrew noise sources.

Now that we have calibrated the meter for the ENR of the noise source, we may read the noise figure
directly in the AUTO position. Before we believe it, a few sanity checks are in order:
1. Manual Yfactor measurement and calculation.
2. Insert a known attenuator between the noise source and preamp ¾ the NF should increase by
exactly the attenuation added.
3. Measure something with a known noise figure (known means measured elsewhere; a manufacturers
claim is not necessarily enough).
Finally, too much gain in the system may also cause trouble, if the total noise power exceeds the level
that an amplifier stage can handle without gain compression. Gain compression will be greater in the on
state, so the detected Yfactor will be reduced, resulting in erroneously high indicated NF. The Gaussian
distribution of the noise means that an amplifier must be able to handle 12 dB more than the average
noise level without compression. One case where this is a problem is with a microwave transverter to a
VHF or UHF IF followed by another converter to the 30 MHz noise figure meter, for too much
total gain. I always place a step attenuator between the transverter and the converter which adjust until
I can both add and subtract attenuation without changing the indicated noise figure.
One final precaution: noise figure meters have a very slow time constant, as long as 10 seconds for
some of the older models, to smooth out the random nature of noise. If you are using the noise figure
meter to “tweak” a receiver, tune very slowly!
Sky Noise Measurement
Another way to measure noise figure at microwave frequencies is by measurement of sky noise and
ground noise3,6. Sky noise is very low, around 6 K at 10 GHz, for instance, and ground noise is due to
the ground temperature, around 290 K, so the difference is nearly 290 K. At microwave frequencies we
can use a manageable antenna that is sharp enough that almost no ground noise is received, even in
sidelobes, when the antenna is pointed at a high elevation. A long horn would be a good antenna
choice. The antenna is pointed alternately at clear sky overhead, away from the sun or any obstruction,
and at the ground. The difference in noise output is the Yfactor; since we know both noise
temperatures, the receiver noise temperature is calculated using the Y(ratio):
The latest version of my microwave antenna program3, HDLANT21, will make this calculation. Since
the measured Yfactor will be relatively small, this measurement will only be accurate for relatively low
noise figures. On the other hand, they are the most difficult to measure accurately using other
techniques. A system for measuring sun noise was described by Charlie, G3WDG7, which also works
well for measuring noise figure from sky noise. He built a 144 MHz amplifier with moderate bandwidth
using MMICs and helical filters which amplifies the transverter output to drive a surplus RF power
meter. The newer solidstate power meters are stable enough to detect and display small changes in
noise level, and the response is slow enough to smooth out flicker. Since my 10 GHz system has an IF
output at 432 MHz, duplicating Charlie’s amplifier would not work. In the junk box I found some surplus
broadband amplifiers and a couple of interdigital filters, and combined these to provide high gain with a
few MHz bandwidth, arranged as shown in Figure 3. I found that roughly 60 dB of gain after the
transverter was required to get a reasonable level on the power meter, while the G3WDG system has
somewhat narrower bandwidth so more gain is required.
Several precautions are necessary:
1. Peak noise power must not exceed the level that any amplifier stage can handle without gain
compression. Amplifiers with broadband noise output suffer gain compression at levels lower than
found with signals, so be sure the amplifier compression point is at least 12 dB higher than the
indicated average noise power.

2. Make sure no stray signals appear within the filter passband.
3. Foliage and other obstructions add thermal noise which obscure the cold sky reading.
4. Low noise amplifiers are typically very sensitive to input mismatch, so the antenna must present a
low VSWR to the preamp.
A noise figure meter could also be used as the indicator for the sky noise measurement, but a
calibrated attenuator would be needed to determine the Yfactor. Using different equipment gives us an
independent check of noise figure, so that we may have more confidence in our measurements.
W2IMU8 suggested that the same technique could be used for a large dish at lower frequencies. With
the dish pointing at clear sky, the feedhorn is pointing at the reflector which shields it from the ground
noise so it only sees the sky noise. If the feedhorn is then removed and pointed at the ground, it will
then see the ground noise. Noise figure meters are convenient, but if you don’t have one, the
equipment for measuring sun and sky noise could also be used indoors with a noise source. The only
complication is that the Yfactor could be much larger, pushing the limits of amplifier and power meter
dynamic range.
Noise Sources
The simplest noise source is simply a heated resistor ¾ if we know the temperature of the resistor, we
can calculate exactly how much noise it is generating. If we then change the temperature, the noise
output will change by a known amount. This would work if we could find a resistor with good RF
properties whose value does not change with temperature, an unlikely combination. There are
commercial units, called HotCold Noise Sources, with two calibrated resistors at different temperatures
with low VSWR. Typically, one resistor is cooled by liquid nitrogen to 77.3 K (the boiling point of
nitrogen), while the other is heated by boiling water to 100°C, or 373.2 K. The preamp is connected to
first one resistor, then the other; the difference in noise in noise output is the Yfactor. Using the Y(ratio),
the preamp noise temperature is calculated:
Since the boiling point of pure liquids is accurately known, this type of noise generator can provide very
accurate measurements. However, they are inconvenient to use, since the receiver must be connected
directly to alternate resistors (the loss in an RF switch would significantly reduce the noise output and
accuracy). Also, few amateurs have a convenient source of liquid nitrogen.
Three types of noise sources are commonly available and convenient to use:

1. Temperaturelimited vacuum tube diode. The noise output is controlled by the diode current, but is
only accurate up to around 300 MHz due to limitations of the vacuum tube. These units generate
around 5 dB of excess noise.
2. Gas tube sources. The noise is generated by an ionized gas in the tube, similar to a fluorescent light
¾ homebrew units have been built using small fluorescent tubes. The noise tubes use a pure gas,
typically argon, to control the noise level. These units typically generate about 15 dB of excess noise.
Coaxial gas tube sources work up to around 2.5 GHz, and waveguide units to much higher frequencies.
One problem using these is that a high voltage pulse is used to start the ionization (like the starter in a
fluorescent light) which is coupled to the output in the coaxial units and is large enough to damage low
noise transistors. Since a noise figure meter turns the noise source on and off continuously, pulses are
generated at the same rate. Since waveguide acts as a highpass filter, the starting pulses are not
propagated to the output, so waveguide gastube noise sources are safe to use, though bulky and
inconvenient. However, they could be used to calibrate a solidstate noise source. Another problem with
all gas tubes is that the VSWR of the noise source changes between the on and off states. If the source
VSWR changes the noise figure of an amplifier, as is almost always the case, then the accuracy of the
measurement is reduced.
3. Solidstate noise sources. Reverse breadown of a silicon diode PN junction in causes an avalanche
of current in the junction which would rise to destructively high levels if not limited by an external
resistance. Since current is “electrons in motion,” a large amount of noise is generated. If the current
density of the diode is constant, then the average noise output should also be constant; the
instantaneous current is still random with a gaussian distribution, so the generated noise is identical to
thermal noise at a high temperature. Commercial units use special diodes designed for avalanche
operation with very small capacitance for high frequency operation, but it is possible to make a very
good noise source using the emitterbase junction of a small microwave transistor.
Typical noise output from an avalanche noise diode is 25 dB or more, so the output must be reduced to
a usable level, frequently 15 dB of excess noise to be compatible with gas tubes or 5 dB of excess
noise for more modern equipment. If the noise level is reduced by a good RF attenuator of 10 dB or
more, then the source VSWR (seen by the receiver) is dominated by the attenuator, since the minimum
return loss is twice the attenuation. Thus, the change in VSWR as the noise diode is turned on and off
is minuscule. Commercial noise sources consist of a noise diode assembly and a selected coaxial
attenuator permanently joined in a metal housing, calibrated as a single unit.
Homebrew Noise Sources
There are three components of a noise source: a noise generator, an attenuator, and the calibration
data of ENR at each frequency. The most critical one is the attenuator; it is very important that the noise
source present a very low VSWR to the preamp or whatever is being measured, since lownoise
amplifiers are sensitive to input impedance, and even more important that the VSWR does not change
when the noise source is turned on and off, since a change causes error in the measurement. Because
an attenuator provides twice as many dB of isolation as loss (reflections pass through a second time),
10 dB or more of attenuation will reduce any change in VSWR to a very small value. Commercial solid
state noise sources occasionally appear in surplus sources, usually at high prices but occasionally very
cheap if no one knows what it is. I have found two of the latter, and one of them works! It produces
about 25 dB of excess noise, which is too much to be usable. I went through my box of hamfest
attenuators and found one which has excellent VSWR up to 10 GHz and 13 dB of attenuation. Mated
with the noise source, the combination produces about 12 dB of excess noise — a very usable amount.
Finally, I calibrated it against a calibrated noise source for all ham bands between 50 MHz and 10 GHz;
not exactly NTIS traceable, but pretty good for amateur work.
While noise sources are hard to locate, noise figure meters are frequent finds. If we could come up with
some noise sources, all the VHFers who have one gathering dust could be measuring and optimizing
their noise figure.

Several articles have described
construction of homebrew noise sources,
which work well at VHF and UHF, but not as
well at 10 GHz. All of them have the diode
in a shunt configuration, with one end of the
diode grounded. When I disassembled my
defective commercial noise source (even
the attenuator was bad), I found a bare chip
diode in a series configuration ¾ diode
current flows into the output attenuator.
Obviously I could not repair a chip diode,
but I could try the series diode
configuration. I found the smallest
packaged microwave transistor available,
some small chip resistors and capacitors,
and soldered them directly on the goldplated flange of an SMA connector with zero lead
length, as shown in the photograph, Figure 4. We’ve all soldered components directly together in “dead
bug” construction; this is more like “flyspeck” construction. The schematic is shown in Figure 5, and it
works at 10 GHz! I built several versions to evaluate reproducibility, and measured them at several ham
bands from 30 MHz to 10 GHz, with results shown in Figure 6. All units were measured with the same
14 dB attenuator, so the diode noise generator output is 14 dB higher (Later I found that the MIT
Radiation Laboratory had described12 a noise source with a series diode 50 years ago, so we aren’t
giving away anyone’s trade secrets.)

I then remembered that I had a commercial noise diode, a Noise/Com NC302L, which was used in a
noise source described in QST11, with the diode in the shunt configuration. The diode is rated as
working to 3 GHz, so, in the amateur tradition, I wanted to see if I could push it higher, using the series
configuration. Since I didn’t expect to reach 10 GHz, I increased the value of the bypass capacitor, but
otherwise, it looks like the units in Figure 5. When I measured this unit, it not only worked at 10 GHz,
but had more excess noise output than at lower frequencies, probably due to an unexpected
resonance. The performance is shown in Figure 6 along with the other units. Also shown in Figure 6 is
the output of my pseudocommercial noise source; even with the external attenuator, the excess noise
output is pretty flat with frequency. Commercial units are typically specified at + or 0.5 dB flatness. In
Figure 6, none of the homebrew ones are that flat, but there is no need for it; as long as we know the
excess noise output for a particular ham band, it is perfectly usable for that band. All the above noise
sources relied on a coaxial microwave attenuator to control the VSWR of the noise source. Attenuators
are fairly frequent hamfest finds, but ones that themselves have good VSWR to 10 GHz are less
common, and it’s hard to tell how good they are without test equipment. An alternative might be to build
an attenuator from small chip resistors. I used my PAD.EXE program13 to review possible resistor
values, and found that I could make a 15.3 dB p attenuator using only 140 ohm resistors if the shunt
lugs were formed by two resistors in parallel, a good idea to reduce stray inductance. I ordered some
“0402” size (truly tiny) chip resistors from DigiKey, more NC302L diodes from Noise/Com, and built the
noise source shown in Figure 7 on a bit of Teflon PC board, cutting out the 50 ohm transmission line
with an XActo knife. The schematic of the complete noise source is shown in Figure 8. The chip
resistor attenuator works nearly as well as an expensive coaxial one. The measured VSWR of two
noise sources, one with the chip attenuator and the other with a coaxial attenuator, is shown in Figure
9. Curves are shown in both the off and on states, showing how little the VSWR changes. The VSWR of
the chip attenuator unit is 1.42 at 10 GHz, slightly over the 1.35 maximum specified for commercial
noise sources, but still fine for amateur use.

Noise Source Alignment
The only alignment requirement for a solidstate noise source is to set the diode current; the current is
always set at the highest frequency of interest. A noise figure meter must be set up with converters,
etc., for the highest frequency at which the noise source might be used, and set to display the detector
output ( OFF position on a model 75). Then voltage from a variable DC power supply is applied to the
noise diode through the 1K currentlimiting resistor. The detector output should increase as the voltage
(diode current) increases, reach a peak, then decrease slightly. The optimum current is the one that
produces peak output at the highest frequency (I set mine at 10 GHz). Then additional resistance must
be added in series with the currentlimiting resistor so that the peak output occurs with 28 volts applied,
so that the noise source may be driven by the noise figure meter. Once the proper resistor is
determined and added, the DC end of the noise source is connected to the diode output of the noise
figure meter, and the meter function set to ON. This should produce the same detector output as the
power supply. Then the meter function is set to AUTO, and the meter should produce some noise figure
indication, but not a calibrated one yet. However, it is good enough to tune up preamps ¾ a lower noise
figure is always better, even if you don’t know how low it is.
Noise Source Calibration
Much of the high price of commercial noise sources pays for the NTIStraceable calibration. Building a
noise source only solves part of the problem ¾ now we need to calibrate it. The basic calibration
technique is to measure something with a known noise figure using the new noise source, then
calculate what ENR would produce the indicated noise figure. Fortunately, the calculation is a simple
one involving only addition and subtraction; no fancy computer program required. Simply subtract the
indicated noise figure, NFindicated, from the known noise figure, NFactual, and add the difference to the
ENR for which the meter was calibrated, ENRcal :
ENR (noise source) = ENRcal + (NFactual NFindicated )
This procedure must be repeated at each frequency of interest; at least once for each ham band should
be fine for amateur use. The known noise figure is best found by making the measurement with a
calibrated noise source, then substituting the new noise source so there is little opportunity for anything
to change. Next best would be a sky noise measurement on a preamp. Least accurate would be to
measure a preamp at a VHF conference or other remote location, then bring it home and measure it,
hoping that nothing rattled loose on the way. If you can’t borrow a calibrated noise source, it would be
better to take your noise source elsewhere and calibrate it. Perhaps we could measure noise sources
as well as preamps at some of these events.
Using the noise source
Now that the ENR of the noise source has been calibrated, the noise figure calibration must be adjusted
to match. However, the model 75 in the CAL position has only two dB of adjustment range marked on
the meter scale. Older instruments have no adjustment at all. However, we can just turn around the
equation we used to calculate the ENR and calculate the NF instead:
NFactual = NFindicated + ( ENR (noise source) ENRcal )
There is a short cut. My noise source has an ENR around 12 dB, so I set the “CAL ADJ” in the CAL
position as if the ENR were exactly 3 dB higher, then subtract 3 dB from the reading. Even easier, the
meter has a +3dB position on the “ADD TO NOISE FIGURE” switch. Using that position, I can read the
meter starting at 0 dB. Any ENR difference from 15 dB that matches one of the meter scales would also
work ¾ rather than an involved explanation, I’d urge you to do the noise figure calculations, then try the
switch positions and see what works best for quick readout.

Reminder: noise figure meters have a very slow time constant, as long as 10 seconds for some of the
older models, to smooth out the random nature of noise. Tune slowly!
Don’t despair if the ENR of your noise source is much less than 15 dB. The optimum1 ENR is about 1.5
dB higher than the noise figure being measured. The fact that today’s solid state noise noise sources
have an ENR around 5 dB rather than the 15 dB of 20 years ago shows how much receivers have
improved.
Conclusion
The value of noise figure measurement capability is to help us all to hear better. A good noise source is
an essential part of this capability. Accurate calibration is not necessary, but helps us to know whether
our receivers are as good as they could be.
Best 73's N1BWT.
Notes:
1. R. Pettai, Noise in Receiving Systems, Wiley, 1984.
2. M.B. Graves, WRØI, “Computerized Radio Star Calibration Program,” Proceedings of the 27th
Conference of the Central States VHF Society, ARRL, 1993, pp. 1925.
3. P. Wade, N1BWT, “More on Parabolic Dish Antennas,” QEX, December 1995, pp 1422. HDLANT21
program may be downloaded from http://www.arrl.org/qexfiles
4. W.E. Pastori, “DirectReading Measurement of ReceiverNoise Parameters,” Microwave Journal,
April 1973, pp. 1722.
5. R. Bertelsmeier, DJ9BV, & H. Fischer, DF7VX, “Construction of a Precision Noise Figure Measuring
System,” DUBUS Technik 3, DUBUS, 1992, pp. 106144.
6. H. Fasching, OE5JFL, “Noise Figure Measurement using Standard Antennas,” DUBUS Technik 4,
DUBUS, 1995, pp. 2325.
7. C. Suckling, G3WDG, “144MHz wideband noise amplifier,” DUBUS, 2/1995, pp.58.
8. R. Turrin, W2IMU, “Method for Estimating Receiver Noise Temperature,” Crawford Hill Technical Note
#20, September 1986.
9. K. Britain, WA5VJB, “10 GHz Noise Source,” Microwave Update ‘87, ARRL, 1987, p 63.
10. P. Wade, N1BWT, & S. Horsefield, NR1E, “Homebrew Solid State Noise Sources,” Proceedings of
the 1992 (18th) Eastern VHF/UHF Conference, ARRL, 1992.
11. W.E. Sabin, WØIYH, “A Calibrated Noise Source for Amateur Radio,” QST, May 1994, pp. 3740.
12. G.E. Valley, Jr., & H. Wallman, Vacuum Tube Amplifiers, MIT Radiation Laboratory Series, McGraw
Hill, 1948.
13. P. Wade, N1BWT, “Building VHF Power Attenuators,” QEX, April 1994, pp. 2829. PAD.EXE
program may be downloaded from http://www.arrl.org/qexfiles

DX NEWS
From the Web
C91, MOZAMBIQUE
Mike, ZS6TAF, who works in Maputo from time to time, operate mobile using the callsign C91BA. He
uses Yaesu 857D and Watson Multiranger mobile antenna for 80/40/20/15/10/6 meters. He was heard
this past week on 7083 kHz at 1539z. QSL via his home callsign.
CCF/OHDXF CONTEST & DX CONFERENCE

Dates for the CCF/OHDXF Contest and DX conference have been announced by the Contest Club of
Finland(CCF) and OH DX Foundation (OHDXF). It will be held between January 2224th (2010). Look
for more details to become available on the following Web page at:
http://contestclubfinland.com/CCF
CE9, SOUTH SHETLAND ISLANDS (Update)

A team of operators will be operating from Arturo PratGreenwich IslandSouth Shetland archipelago
(IOTA AN010, WW Loc. GC07FQ), between January 1024th. Team members mentioned are:
Luis/XQ5CIE, Carlos/CE6UFF, Didier/F6DXE and Dagoberto/CE5COX. Their callsign will be XR9JA.
Activity will be on 1606 meters using CW, SSB, PSK31 and the AO51 Satellite. QSL via CE5JA. For
more information, go to:
http://www.ce5ja.cl
FT5W, CROZET ISLAND

Florentin, F4DYW, currently active as FT5WO, is expected to be on the air until November 15th, but will
leave the island on November 23rd. He is usually on 20 or 17 meters during Saturdays and Sundays
between 06001300z usually between 1426014280 kHz. QSL via F4DYW.
MARCONI NOBEL 100 AWARD

To celebrate the 100th anniversary of Marconi receiving the Nobel Prize, listen for and work 10 different
special event "SI" stations between November 9th and December 10th. The following special
anniversary callsigns will be on the air: SI0GM, SI1GM, SI2GM, SI3GM, SI4GM, SI5GM, SI6GM and
SI7GM. Other SM stations may be using the special prefix SI, but only the above stations count. Each
anniversary station counts once per band. No endorsements. The fee is 50 SEK, 5 Euro or 5 USDs.
Apply with log entry to SSA Awards Manager, Bengt Hogkvist, Ostbygatan 24 C, SE531 37 Lidkoping,
Sweden
P4, ARUBA (SA036)

John, W2GD, will be active as P40W during the CQ WW DX CW Contest (November 2829th) as a
SingleOp/AllBand/LowPower or QRP entry with limited antennas. QSL via N2MM. Logs will be loaded
on LoTW upon his return to USA.
P4, ARUBA (SA036)

Andy, AE6Y, will be active as P49Y during the CQ WW DX CW Contest
(November 2829th) as a SingleOp/AllBand/High (or Low)Power entry.
QSL via AE6Y.

T30, WESTERN KIRIBATI
Operators David/N1EMC and Mike/N1IW will be active as T30KI and T30IW, respectively, between
November 1016th. Activity will be on 606 meters as conditions permit using SSB/CW. QSL via N1EMC.
T6, AFGHANISTAN
David, CT1DRB, will be active as T6AG from here the next 6 months as of October 21st. Activity will
only be CW. QSL via EA3GHZ direct.
TZ, MALI
Mac, JA8SLU, will once again return to Mali and be active as TZ6JA between November 223rd. Activity
will be SSB only. QSL direct only to: Mac Obara, P.O. Box 59, Tama, Tokyo, 2068691 JAPAN.
V3, BELIZE
Wil, AA4NC, will be active as V31RR between February 1723rd. Activity will be on the HF bands
including 30/17/12m using CW, SSB and RTTY. His activity will also include the ARRL DX CW Contest
(February 2021st) as a SingleOp entry. QSL via his home callsign or LoTW.
XV, VIETNAM (Update/IOTA Op)

Operators Manfred/DK1BT, Wolf/DL4WK, Andy/ DL5CW, Sigi/DL7DF and Frank/DL7UFR will be active
as XV4D from Phu Quoc Island (AS128) between November 417th. Activity will be on 16010 meters
using CW,SSB,RTTY,PSK and SSTV. QSL via DL7DF, direct or by the Bureau.
YN, NICARAGUA
Eric, K9GY, will once again be active as YN2GY from Octavio's, YN2N, QTH in Grenada, during the
2010 ARRL DX CW Contest (February 2021st) as a SingleOp/AllBand/LowPower entry. He will be
there between February 1822nd. Outside of the contest, look for CW activity on 30/17/12 meters. QSL
via LoTW or to his home callsign, direct or by the bureau.
CONTESTS OF THE MONTH

Date UTC Mode Contest
0607 12001200 All Ukrainian DX Contest

0608 21000300 CW ARRL Sweepstakes
0608 21000300 CW Collegiate Championship
1314 07001300 SSB Japan International DX Contest
1314 00002400 RTTY Worked All Europe DX Contest
1314 12001200 CW OK/OM DX Contest
2021 14000800 CW IARU 160m Contest
2022 21000300 SSB ARRL Sweepstakes
2022 21000300 SSB Collegiate Championship
2021 21000100 CW RSGB 1.8MHz Contest
2021 12001200 CW LZ DX Contest
2728 00002400 CW CQ WW DX Contest

S M3 C V M P r e s e n ts :
T HE DX CAL E NDAR
No vemb er 2009
1/11 ANTARCTICA; VKØBP AN016

is currently working at Antarctic Davis Base Station, Gridsquare MC81xk. His activity is limited due to
his workload, but he is expected to be on all HF bands. He seems to like 20 meters between 1500
1800z. Operations have been on SSB and PSK31, but he plans to operate on other modes later on
during his stay at the Davis Station. QSL via VK2CA. PLEASE NOTE: There is also a possibility of
activating other field huts in the area, and he will sign as VK0BP/P. Look for more details on his Web
page at http://www.vk0bp.org/
1/11 7/11 ARGENTINA; LU/PY2TJ SA008

from Isla Tierra Del Fuego (WLOTA L2448). Activity will be on all HF bands. QSL via PT2OP, direct is
preferred or by the Bureau.
2/11 9/11 UNITED STATES OF AMEICA: KG8DP NA062

from Grassey Key. Operations will be stationary at Grassey Key and mobile as he travels to Key West
and all points on the ocean. He will use the callsign KG8DP, as well as his club callsign NA8KD. This
will be a week trip. QSL both KG8DP/NA8KD via info on QRZ.com (w/SASE). Mark will be using an IC
7000, 1.2 kw amp mobile and GLA1000B portable amp. Antennas were not mentioned.
2/11 23/11 MALI; TZ6JA

by JA8SLU. Activity will be SSB only. QSL direct only to: Mac Obara, P.O. Box 59, Tama, Tokyo, 206
8691 JAPAN.
3/11 15/11 MONTSERRAT; VP2MUM, VP2MXO and VP2MNK

by DL2RUM (VP2MUM), DM2XO (VP2MXO) and DJ8NK (VP2MNK). Activity will be on 16010 meters
using CW, SSB and RTTY. QSL via their home callsigns per the QRZ.com address or by the Bureau.
4/11 11/11 VIRGIN IS; KP2/homecall

from St. Croix by N3XF, K1ZE and W1EQ. Activity will be on 16010 meters using CW, SSB and
possibly RTTY. Look for KP2M during the ARRL CW Sweepstakes Contest (November 78th). QSL
KP2M via info on QRZ.com. All other QSLs via home callsign and LoTW.
4/11 17/11 VIET NAM; XV4D AS128

from the Island of Phu Quoc by DL7DF, who will lead a crew of operators. Their callsign has not been
announced yet, but it is expected to be the XV prefix. Activity will be on 16010 meters using CW and
SSB with several stations on the air. One station will be exclusively dedicated to RTTY, PSK31 and
SSTV. Their equipment consists of 3 transceivers (two K2 and one IC7000) with three kW linears into
two 18m lowband verticals, a 2 element vertical for 40m, a 2 element vertical for 30m, two Spiderbeam
for 20/17/15/12/10m, and some beverage antennas. Operatorsmentioned are: DK1BT, DL4WK,
DL5CW, DL7DF and DL7UFR. Pilot station for this DXpedition is Bernd, DF3CB. QSL via DL7DF, by
the German QSL Bureau or direct to: Sigi Presch, Wilhelmsmuehlenweg 123, D12621 Berlin,
Germany. For complete details, visit http://www.dl7df.com/xv/index.html

4/11 18/11 BERMUDA; VP9KF NA005
from Baileys Bay by W4/VP9KF (G4BKI). Activity will only be CW on all bands. QSL via W4/VP9KF:
Paul Evans, 6809 River Road, Tampa, FL 33615. Visit his Web page at http://vp9kf.com/
Please, DO NOT send to the VP9 bureau.
6/11 8/11 EAST MALAYSIA; 9M6DXX/P and 9M6XRO/P OC133

from Pulau Labuan Island by 9M6DXX and 9M6DXX. The operations will be as follows: 9M6DXX/P On
8010 meters; SSB only. 9M6XRO/P On 16010 meters; CW and RTTY. Each stations will be using
amplifiers to a multiband vertical and a 160m invertedL, both mounted very close to the ocean.
Operators hope it will be possible to operate on 160m CW at the same time as SSB on the other bands.
QSL both 9M6DXX/P and 9M6XRO/P via M0URX, either direct, by the bureau or LoTW.
6/11 9/11 VENEZUELA; YW5F SA058

from Farallon Centinela Island by members of the Grupo DX Caracas. Activity is to celebrate the 20th
anniversary of the Caracas DX Group. Operations will be on 802 meters using CW, SSB and FM. QSL
via DM4TI.
7/11 NIUE; ZK2DL OC040

by DL2FAG. He plans to operate mainly RTTY, PSK and SSB on 1080 metres, using a Triple leg
multiband and dipoles. After Niue and before Samoa he will be visiting New Zealand's South Island (OC
134) and be active sporadically as ZL4/DL2FAG. QSL via home call. Log searches will be available at
www.qsl.net/dl2fag/
9/11 PAPUA NEW GUINEA; P2 OC102, OC231 and OC205

G3KHZ (P29NI) has announced a new IOTA DXpedition from the Tanga Islands (OC102), the Green
Islands (OC231) and the Woodlark Group (OC205). He and other four operators, CT1AGF, G3USR,
G4EDG and SM6CVX) will operate CW, SSB and RTTY on 16015 metres, using new single band
vertical dipoles for 3015m and a ground plane for 40m.
11/11 NEW CALEDONIA; FK/F5NHJ OC032 or OC033

from either Grande Terre (OC032) and Lifou or Mare (OC033).He plans to focus on 30 metres digital
modes. QSL via F5NHJ.
10/11 16/11 W. KIRIBATI; T3ØKI and T3ØIW

by N1EMC and N1IW. Activity will be on 606 meters as conditions permit using CW/SSB. QSL via
N1EMC.
11/11 13/11 PAPUA NEW GUINEA; P29VCX OC117

from Hastings Island by SM6CVX. QSL via home call. The web page for the expedition is at
http://www.425dxn.org/dxped/p29_2009/
11/11 16/11 BRAZIL; PW6C SA062

from Coroa Vermelha Island by PP1CZ, PY0FF, PY7RP, PY7XC, PY7ZY and K9AJ. Activity will be on
8010 meters using CW and SSB. QSL via K9AJ. Web site at http://www.pw6c.com/
11/11 18/11 SAMOA; 5W OC097

from the Island of Upolu by IK1PMR, K2LEO/PA3LEO, PA0BWL, AA4NN, OE2SNL, DJ5IW and
OZ1IKY are planning a DXpedition to three semirare entities (and possibly some other operations) in
the Pacific between November 11th and December 13th. Callsigns have not been announced yet.
Focus will be on the lower bands, but activity is planned for 16010 meters using CW, SSB and the
Digital modes. The team will use three Elecraft K2/100 with DSP and amps. For more information and
updates, watch: http://www.ik1pmr.com/plans/a3/index.php?s=intro/

from Normanby Island by SM6CVX. QSL via home call. The web page for the expedition is at
13/11 23/11 COMOROS; D68F AF007

by F6AML. He will operate CW (1828, 3520, 7020, 10115, 14020, 18071, 21020, 24951 and 28020
kHz) and SSB (3775, 7075, 14265, 18140, 21265, 24960 and 28480 kHz), with a focus on the low
bands. QSL via F6AML, direct or bureau.
13/11 27/11 GHANA; 9G5TT and 9G5XX AF084

Their activity will also include an IOTA trip to Abokwa Island (AF084). Operations on the mainland will
use the callsign 9G5TT, while operations on AF084 will use 9G5XX. Activity will be on all HF bands
(16010 meters) and modes. On AF84 there will be one station on 20 meters only. The time of the
operation on the island will be on a day to day basis and will depend on the sea condition and weather
forecast. QSL via I2YSB, direct only. More information can be found at http://www.i2ysb.com/
13/11 REPUBLIC OF KOREA; HL9QST

by KE7WRJ. This is a rare prefix only assigned to U.S. Service members assigned to Korea. His
tentative schedule is to operate from 4 different locations in South Korea as follows: September 10
12th: Seoul, September 1424th: Camp Casey, September 25thOctober 18th: Camp Humphreys,
October 1929th: Camp Carroll October 30thNovember 13th: Seoul. Activity will be on 4010 meters,
depending on the propagation, using CW and SSB. Operations will be at least 8 hours a day during the
week and longer over the weekends. Look for him to be in both the Extra and General portions of the
bands. His equipment will consist of a 5000A by Flex Radio, a "3 element Yagi in a Bag" from Super
Antennas. QSL via KE7WRJ, direct or LoTW.
14/11 21/11 FALKLAND IS.; VP8BUG (digital) and VP8BUH (SSB)

by members of the Uruguay DX Group's globetrotters. Their activity will focus on the lower bands,
Digital modes and the 30/17/12 meter bands. Operators mentioned include: Gus/CX2AM, Gus/CX3CE,
Bert/CX3AN, Mario/CX4CR and Luis/CX4AAJ. Probably QSL Manager is EB7AEY. More details are
forthcoming.

from Loloata Island by SM6CVX. QSL via home call. The web page for the expedition is at
15/11 3/12 TURKS & CAICOS IS.; VP5/homecall NA002

from Providenciales by W7VV, VE7XF and possibly some other operators.Activity will include the
CQWW DX CW Contest (November 2829th) as a Multi? entry and possibly a special callsign (TBA).
QSL route TBA. Operators will be active before and after the contest on all bands (1606 meters) and
modes signing VP5/homecall. QSL via their home callsigns.
15/11 20/2 2010 ANTARCTICA; KC4USV AN011

from McMurdo Station by K7MT. He will be on the HF bands on 14243 kHz, Sundays at 0000z. He will
also be active on PSK31 (on 14070 kHz) and CW (14043 kHz) if time permits. He has also mentioned
that he will take an Arrow II antenna and his Kenwood TH7 to work the Amateur Satellites into VK and
ZL land. He also has plans to be on APRS VHF/HF with a Kam Plus, so you might just see him driving
around on the Ross Ice Sea as K7MT7 on APRS. QSL via K1IED. Visit his home page for some
interesting pictures at http://www.mt.net/~k7mt/

15/11 CROZET I; FT5WO
by F4DYW. He is usually on 20 or 17 meters during Saturdays and Sundays between 06001300z
usually between 1426014280 kHz. QSL via F4DYW.
ca 16/11 LEBANON; OD/W5YFN

has received approval from the local authorities while in Lebanon, for one year starting on 16 November.
17/11 AUSTRALIA; VK7ACG OC006

from Tasmania by GØWFH. He will operate SSB on 16010 metres, with a focus on the low bands. QSL
via home call, direct or bureau.
17/11 30/11 SAMOA; 5WØKH OC097

from Upolu Island by DL2FAG. He plans to operate mainly RTTY, PSK and SSB on 1080 metres, using
a Triple leg multiband and dipoles. QSL via home call. Log searches will be available at
www.qsl.net/dl2fag/
17/11 15/12 MADAGASCAR; 5R8IC AF090

from Saint Marie Island by F6ICX. Activity will be on 8010 meters. QSL via his home callsign.
18/11 24/11 CANADA; VY2/W7ASF NA029

from Prince Edward Island. Activity will include an entry in the ARRL Sweepstakes Phone ontest
(November 2123rd). QSL via his home callsign, direct or by the Bureau.
19/11 23/11 NEW CALEDONIA; FK/JA1NLX OC033

from Ouvea Island along with his XYL. Activity will be on all HF bands (8010 meters) using CW and
RTTY with a IC706MK2 100 watt transceiver and vertical antenna. QSL via the LoTW or by his home
callsign, direct or by the Bureau. For more details and log after his operation, visit the following Web
page at http://www.ne.jp/asahi/ja1nlx/ham/fk_2009.html
19/11 9/12 TONGA; A3 OC049

from the Island of Tongatapu by IK1PMR, K2LEO/PA3LEO, PA0BWL, AA4NN, OE2SNL, DJ5IW and
OZ1IKY are planning a DXpedition to three semirare entities (and possibly some other operations) in
the Pacific between November 11th and December 13th. Callsigns have not been announced yet.
Focus will be on the lower bands, but activity is planned for 16010 meters using CW, SSB and the
Digital modes. The team will use three Elecraft K2/100 with DSP and amps. For more information and
updates, watch: http://www.ik1pmr.com/plans/a3/index.php?s=intro/
20/11 26/11 CANADA; VY1RST

from near Beaver Creek, Yukon by KL7JR, WL7MY and KL7BO. Emphasis will be on 160/80 meters
SSB (using a 160m Inverted L) with a 2nd station on for 4010 meters (vertical) SSB and PSK31. QSL
Manager is KL7JR. Email skeds are welcome at John.ReisenauerJr@alyeskapipeline.com
20/11 10/2 2010 CANARY ISLANDS; EA8/homecall AF004

from Tijoco Bajo, Tenerife Island by ON5JV and ON6AK. Activity will be on 4010 meters during their
evenings. They plan to use 100w into a vertical 14AVQ. QSL via their home calls, bureau is preferred.
21/11 5/12 CHRISTMAS I.; VK9XX OC002

by DM5TI, DL2JRM and DL2RMC. Activity will be on 16010 meters using CW, SSB and the Digital
modes. They plan to use verticals and beams, and also be an entry in the CQWW DX CW Contest as
VK9XW (November 2829th). QSL via DL1RTL, by the Bureau or direct. For complete details, visit the
VK9XX Web site at http://www.dl2rmc.com/tom/VK9X2009/

22/11 2/12 BARBADOS; 8P9SS
by ND3F. Activity will probably be on all bands, but he will also be in the CQWW DX CW Contest
(November 2829th) as a SingleOp/AllBand/LowPower entry. QSL via LoTW or direct to ND3F.
23/11 1/12 BOTSWANA; A25NW

by K9NW. Activity will include the CQWW DX CW Contest (November
2829th). QSL via his home callsign (QRZ.com).
23/11 2/12 TUNISIA; 3V3S

by a German team from the "Radio Club Station of Tunisian Scouts" (3V8SS) in Sousse. Operators
mentioned are DJ7IK, DJ8NK, DJ9CB, DL9USA and DF1LON. The team will set up, and use a
spiderbeam and verticals antennas. All antennas will be donated to the 3V8SS station. Look for them to
also participate in the CQWW DX CW Contest (November 2829th) as a MultiSingle/LowPower entry.
QSL via DL9USA. A Web page will be active soon at http://www.3V3S.tk/
23/11 6/12 CHESTERFIELD IS.; TX3A

by AA7JV and HA7RY. The TX3A license is valid for 14 days only between the dates listed above.
Because these dates could change (due to weather and other things), they "may" have to operate as
FK/AA7JV or FK/HA7RY before and after this period. Their priorities will be 160, 80 and 40 meters, in
that order. They will be active on the higher bands the rest of the time. The operators will use the same
antenna that they used on Mellish Reef, but they have developed a new RX antenna, which they hope
will improve their RX capabilities. QSL via HA7RY. Mailing direct Please include 2 USDs with every
direct QSL request for up to three cards per envelope. If you send International Reply Coupons (IRC),
please make sure that it is not expired or is not about to expire. DO NOT SEND IRCs that are valid only
until end of 2009! Cards are likely to be posted only early 2010. Mailing address: Tamas Pekarik, Alagi
ut 15, H2151 Fot, HUNGARY. * The preferred way is using the "Online QSL Request Service" (OQRS)
on their Web site which they will launch once the DXpedition is over. You can use that form to request
your direct QSL and cover the costs of sending the QSL card to you direct by using PayPal. They
request a minimum of 5 USDs or 4 EUROs for this service. * Bureau: They will launch an "Online QSL
Request Service" (OQRS) on their Web site as soon as the expedition is over. If you want to receive
your QSL via the bureau, please use that form to request the card. They will check your QSOs against
the log and send your card to you via the bureau. This method will allow them faster processing, helps
them protect the environment and you will receive your TX3A card faster. If you request your bureau
card online, please do NOT request a direct card and do NOT send us your QSL card. More detailed
information is available on their new Web page at http://www.TX3A.com/
24/11 1/12 BONAIRE, CURACAO; PJ4/homecall SA006

from Bonaire by K4BAI and W4OC. Also look for them to be active as PJ4A during the CQ World Wide
DX CW Contest (November 2829th) as a MultiOp entry. QSL all callsigns via K4BAI.
24/11 6/12 BELIZE; V31PT NA073

from Ambergris Cay by K8PT. No other details were provided. However, in past operations, activity
usually is 1606 meters using CW, SSB, RTTY and some PSK31. QSL via his home callsign.
25/11 27/11 MARTINIQUE; FM/JE1JKL/p

Activity will also include the CQWW DX CW Contest, signing as TO5T, and as a SingleOp/All
Band/HighPower entry. QSL via JE1JKL.
26/11 1/12 ANTIGUA & BARBUDA; V26K

by AA3B. His activity includes the CQWW CW Contest (November 2930th) as a SingleOp/All
Band/LowPower entry. This will be an all CW operation on the contest HF bands only. QSL via AA3B.

A Hundred Year of
Amateur Radio
By G3NGD
"Par t TTwo""
the nexxt fifty yyeeaars..
The war against Hitlers Germany ended, officially at one minute past midnight on Tuesday, May 8,
1945, but the struggle against Japan continued until August 14, 1945. During the weeks that
followed, conditions near to chaos existed on the amateur bands, mainly because certain allied
military commanders in widely different parts of the world had given permission for prewar licence
holders to operate service transmitting equipment. This was a direct contravention to the law, but was
done to boost morale.
In March 1946, questions were asked in Parliament as to

the sale of Government surplus radio equipment to
amateurs. Already much use of the surplus apparatus had
been purchased in large quantities at ridiculously low
prices by dealers who had offered it for sale to show high
profits. Three months later, the Admiralty announced that
"electronic scrap" would become available to radio
amateurs from Naval depots at a price of fifty shillings a
hundredweight. (£2.50) How many complete receivers,
transmitters and items of expensive measuring
equipment was sold in brand new condition as "electronic scrap", no one can even hazard a
guess, but fair minded amateurs regretted that due to abuse, this scheme was abandoned within six
months.
Many radio operators from the war became interested in amateur

radio and applied for licences. People tuning the shortwaves on
domestic receivers discovered the world of amateur radio and
became fascinated. By 1947, more than five and a half
thousand transmitting licences were in force compared with three
thousand eight hundred a year earlier; and so the number grew.
After the war, the "TransAtlantic tests" and the "National
Field Day" events were revived, and are still held annually to this
day. These events are organized by the Radio Society of Great
Britain (formerly the London Wireless Club).

In 1951, the RSGB offered to establish a communications network to meet any national disaster on
land, at sea, or in the air, but the Post Office declined the offer.
During the last few hours of January 1953, a flood disaster of immense magnitude struck the East
Coast of England; Post Office telephones, Government wireless stations and utility services were
out of action for days. Radio Amateurs in these stricken areas, ignoring the terms of their licence
placed their experience at the disposal of the authorities.
After long talks with the Post Office, the RSGB set up the Radio Amateurs Emergency Network
(RAYNET) , which today works in collaboration with the British Red Cross Society, the St. Johns
Ambulance Brigade and the Police.
Early in 1954, the Post Office introduced a new

Amateur Mobile and Television licence. The mobile
age had arrived; amateurs started to build mobile
equipment and demonstrate it at mobile rallies. The
first mobile rally was held at Binsey near Oxford, on
October 9th, 1955, and was attended by over
seventyfive radio amateurs and friends.
For several hours, mobile operators
demonstrated their equipment and discussed the
fine points of this absorbing
new development in
amateur radio. Many
amateurs have become interested in space techniques, and this has led to the
creation of the amateur satellite service in 1971. The OSCAR (orbiting satellite
carrying amateur radio) satellites are now an accepted and exciting part of
the amateur scene.
The 'seventies
Radical changes occurred during the 'seventies. The shelves of "electronic scrap" at the local
amateur radio emporium were replaced by expensive Japanese radio equipment. The new
generation of radio amateur has become a "black box operator" (not interested in how it works).
The Post Office introduced a VHF (Very high frequency) only licence, which an applicant can obtain
without passing a Morse test. This licence restricts the holder to VHF and UHF working only, and
deprives him/her of the thrill and excitement in communicating with people all over the world using
the shortwave bands. It is not until he/she has become proficient in the Morse code that he/she will be
granted a FULL LICENCE.
On 14th September 1972, the first UK repeater was activated with the callsign GB3PI and was
located in Cambridge at the Pye Telecom site. Soon after,
other repeaters were set up and they operated on 2m and
70cm bands.
In 1977, the separate mobile and amateur television
licences were abolished, and these modes of operation were
included in the main licence (One Fee).
At the World Administrative Radio Conference in 1979, three
new bands were gained: 10∙100 10∙150MHz, 18∙068
18∙168MHz, and 24∙890 24∙990MHz.

Many "old timers" like myself try to hold onto the past. This has been shown by the many people still
building Amplitude Modulated (AM) Transmitters and Receivers, and participating in contacts on a
regular basis on Top Band (1963KHz). Listen every Sunday morning at 1100Hrs there is a lot of
activity in the Greater Manchester Area. G3NGD operates using his HOME BREW Chatterbox
Transmitter & Receiver.
The 'eighties
In the early 'eighties, the old 405line vhf television services finished broadcasting in the uk. This
used to be an Amateur Radio band until the BBC acquired it for television after the second world war.
Radio Amateurs requested the band be returned, and this was granted in 1983 (The band is 50
52MHz.).
In the 1980's, Information Technology and the Computer age arrived.
Radio Amateur enthusiasts like myself started to purchase or build the
Sinclair ZX81 microcomputer. This escalated to the introduction of the
INTERNET.
Unfortunately, the Internet has led to a reduction in recruitment of
Radio Amateurs it is so easy to contact people worldwide using the
'Internet'. This is all well and good but one doesn't get the thrill of that
exotic contact especially when using home constructed equipment.
(Prior to the year 2006, the licence fee was only £15 per year now it is FREE of charge!). On the
positive side however,
Radio Amateurs put the Computer to excellent use in:

Slow Scan Television, RTTY, Packet Radio, Using the PC for Logging, Mail Box, Database, Satellite
Tracking, Sending CW for Moon bounce and Meteor Scattering, Chordial Hop Predictions, Distance &
Bearing for Beam Settings, Design Calculations, Echolink Communications, and many other
applications...
Space Operation:
With the advent of the American Space Shuttle, space flight
became a comparatively normal event and Amateur Radio was
allowed on a number of missions. The first amateur operation from
space was W0ORE using a Motorola handheld.
Further missions took radio amateurs into space, and in 1985 an all
German crew operated with the callsign DP0SL. For Britain there
has been operation from space, when the first British cosmonaut,
Helen Sharman, went up with a Russian MIR space mission in May
1991 using the callsign GB1MIR.

The 'nineties
The number of people entering Amateur Radio began to fall, and so in 1991, a new Licence 'The
Novice Licence' was introduced. This was really a way of encouraging young people to participate in
the hobby without having to take a full examination. To qualify for the licence, applicants needed only
to take part in a course organized by the Radio Society of Great Britain and sit a simple examination.
Although many people took up the hobby via this route, the number of Licensees continued to fall, and
so in 1999, the A/B Licence was introduced. For this licence, in addition to a pass being required in
the RAE, one has only to take a Morse test at five wpm.
(Note: pressure was placed on the authorities to abolish the Morse code examination after the year
2000. This has now taken place and has made it very easy to obtain a licence). Many people today are
in for the easy option. They want qualifications to be given away with very little effort being made by the
individual. There were many Radio Amateurs that opposed this move, as Morse Code has many
advantages:
using Morse with 'Q' codes for example, provides an "International language"
Morse Code gets through the interference
Morse Transmitters are simple for the novice to build (no modulator to build)
Morse Code Transmitters have a narrow bandwidth, occupy less radio spectrum and unlikely to cause
EMC problems. In the 'old days', Radio Amateurs were very proud to be associated with the hobby, but
today, the general public think that Amateur Radio is like C.B. radio. This is far from true, and should
remain that way.
This has been shown in the year 2006, when a move to deregulate Amateur Radio was defeated.
Radio Amateurs still have to take an examination to obtain a licence.
However, if the Radio Amateur has an email address, the licence is issued 'free of charge' for life.
Unfortunately, people who don't have computer access have to pay a charge of £20.00 to Ofcom.
(There are no age concessions). Radio Amateurs will
have to confirm their details every five years by email. No doubt, Radio Amateurs will have to
download the latest edition of the Licence Conditions from the Ofcom website, on an annual basis.
Throughout the world at the present time (Year 2000) there are just short of three million radio
amateurs with their own radio stations communicating regularly with other enthusiasts in their own
country and more distant countries. Japan heads the list with 1296000 licences, followed by the
USA with 679864. The United Kingdom has 57124 not including club stations. To these figures,
however, one must add the teens of thousands of amateurs who merely "listen" to amateur radio
broadcasts. If amateur radio is to survive, we need to encourage more people, particularly
youngsters into the hobby. With this in mind, there is a 'proposed future structure' of Amateur Radio
Licensing currently in discussion, as follows: Full Class A, Full Class A/B and Full Class B becoming a
new class 'ADVANCED'. The Novice Class A becoming an 'Intermediate' and the Novice Class B
becoming an 'Intermediate Foundation' Licence.
As the future unfolds, communications equipment will become
more sophisticated; already with the advent of the "silicon
chip", the conventional amateur radio station is becoming
obsolete. Much use has already been made of computers as
detailed above. Amateur Radio has already been used to make
contact with astronauts in space. The future years will
unequivocally show a considerable growth in the use of amateur artificial satellites for long distance
VHF communication. Using the latest techniques and improvements in amateur radio equipment
and satellites themselves, that which is now a very specialized field will become a major amateur
activity. TransAtlantic contacts will become as simple as talking on the telephone to a friend across
town.
73's ! G3NGD

MF and HF Receiving Antenna
By VE7BPO
Introduction
My first shortwave antenna was a simple endfed wire which started at my bedroom window and
extended out horizontally to a tree which was 25 feet away from our house. The antenna feed line was
a short piece of wire that connected to the near end of the antenna and entered the house through a
small hole I made in my wooden window sill. This feed line was directly connected to my receiver's high
impedance antenna input. My station ground was long piece of wire that was connected to a copper
pipe located in the bathroom next door. While this antenna brought in "the world" to my bedroom, it was
extremely noisy. Directly connecting your antenna feed line and house ground system to your receiver
are not good RFI reduction practices. This web page will explore some experiments in trying to
minimize the Radio Frequency Interference (RFI) arising from my local environment.
Indoor RFI sources are usually plentiful. Electrical

appliances such as washing machines, televisions, DVD
players, computers and electrical wiring may all emit RFI
which your antenna, or directly connected house ground
system may pick up and feed to your receiver. Certain
indoor devices may be really strong RFI sources and will
have to be eliminated or decoupled. Outside of your house
are also potential sources of RFI. These may include such
things as power transformers, electric fence and garage
door openers. RFI location and reduction is out of scope for
this web page, however a good place to learn more is the
ARRL RFI book. To find RFI sources in your home and neighborhood, try using a battery powered AM
radio. At my QTH, I located a noisy VCR inside the house my Grundig S350. We rarely use this VCR
and now just leave it unplugged until we actually need to operate it. I tuned the receiver to an empty
frequency and found this VCR by trial and error. Please note this web page is concerned with feeding a
shortwave listening antenna and does not describe providing protection against lightning. For web sites
which covers lightening plus RF ground please refer to this offering from W8JI or eHam.net.
Protect your home and family from lightening !!

Outdoor MF and HF Antenna
The schematic to the left summarizes the

outdoor VE7BPO MF and HF receiving
antenna system for summer 2007. Although
modest for a big city lot, this antenna seems
to pull in the DX and is relatively free of RFI.
This antenna was just a case of "putting as
much wire in the sky as possible" and the
dimensions are indicated for interest sake
only. The 27 meter long horizontal section is
supported between 2 trees at a height of
about 14 meters high. The weight of the
vertical element wire plus slack in the
horizontal wire droop it to about 13 meters
high in the center. The vertical section is
soldered to the horizontal wire 6 meters from
the nearest anchoring tree and runs straight down to the antenna feed point which is about 1 meter off
the ground. The feed point is a piece of copperclad PC board (with isolated sections created with a
hobbyist motor tool) and is bolted to a long copper pipe which serves as the first station earthgrounding
stake. A transformer (T1) configured as a UNUN (unbalancedtounbalanced) is used to interface the
antenna with 50 ohm coax that runs through the house and into the radio shack. Some rudimentary
experiments with the UNUN and the earthgrounding system were undertaken.
The methods I used to potentially lower unwanted RFI to my antenna system are as follows:
1.The receiver and power supply are independently connected to a single, central ground point (ground
buss) in the radio shack.
2.610 gauge wire is used for my ground system (not including the radials which are bare 12 gauge
wire).
3.The ground wire connecting to my first earth stake to the station ground buss is just outside the shack
window and is short as possible to provide a low impedance and low inductance path for MF and HF
frequencies.
4.There is a second ground stake located 1 meter from the primary ground stake (I will add 24 more in
time).
5.I have a large piece of steel buried underneath the soil tied in to my system as well as 3 bare copper
radials. The radials are 3 7 meters in length.
6.New RG58/U coax was used as the feed line.
7.All wire splices in the grounding system are soldered and taped up. I used conductive grease (to
prevent oxidation at the wirestake interface) on any clamps connected to ground stakes. My ground
stakes are ~ 2 meters long.
8.The earth grounding area soil is moist and peatladen and is watered regularly.
9.I plan to maintain this ground system every 2 years.
Best 73's ! VE7BPO

The HAM‐MAG's
HALL OF FAME
List of generous donators
FEBRUARY 2009 : MAY 2009 :

PAØNCV, Nick Mark Wall
K6LCS, Clint G3VFP, Dave
Richard Downey Ross Bell
VK2ETA, John Edwin Weal
Laurent Horne KD5WQD, Don
K4SHF, Tim MØWYM, Charlie
KE4IAP, Don WE9C, Gene
K3PB, Pat EA2HI, Herman
W2FBS, Richard
VK2SJJ, Steven JUNE/JULY 2009 :
CT1ADT, Manuel WB5TKI, Doug
KB1KRS, Hyrum W9BF, Robert
2IØCOS, Cornelius WB8YWA, James
KA5DON, Don W2KRH, Ken
PY3ARS, Jocarli Gilbert Houck
W3ACO, Rich Robert Mendelson
NØAX, Ward Robert Liesenfeld
MØWAY, wayne M1ERF, Roy
Antonio de Armas Medina PA3DOO, Nico
K3ZIV, Bill Jose Fernandez
Milan Puncer www.soytives.com
EA6BB, Pedro Urszula GandorGraham
W1CRO, Arthur KD8IXP, Fred
KA8Q, Jerry
AUGUST 2009 :
MARCH 2009 : NQ9A, Carolyn
Kenneth Holloway N8SHZ, Bela
Wolfgang Hoeth Richard Vuillequez T HANK Y O U !
W7RDP, Doug Tony Humphris
AB7OC, Michael OM3AG, Ladislav
Clint Bradford
W2AFD, Howard SEPTEMBER 2009 :
Joshua Emmott Kirk W Bumgarner
APRIL 2009 : OCTOBER 2009 :

AF6IM, Mark Newton White To make a donation, have a look on
F1AGR, Gilles Jerry France the website
GMØMDD, John Clough N6DVA, Paul http://www.hammag.com
IZ1NEO, Gaetano And click on "Help us"
Dennis Finegan
worksat.com

C O M I C ' S HA M
H a v e s o m e f un ...
HAM cats !
HAMMAG N.10 November 2009
Chief Editor : Vincent Faucheux F5SLD

Design & conception : V.N.A.C.E.
This issue does exist thanks to : G3NGD, K0HL, KA6KBC,
N1BWT, OPDX, SM3CVM, southgatearc.org, VE7BPO, ZS2ABF.
Send your informations to : f5sld@free.fr
Website : http://www.hammag.com
This magazine has been sent to 6,900 Emails
Erratum : concerning the photo of the article "Takantenna"

(Hammag N.9), the call was KI6HRH (not KI6RHR), sorry for
this mistake.

HamMag - Noise Measurement

Uploaded by

Copyright:

Available Formats

HamMag - Noise Measurement

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HamMag - Noise Measurement

Uploaded by

Copyright:

Available Formats

HAM-MAG

F5SLD's Free HAM Magazine ­ 100% HAM RADIO

D I Y Patch Box 4 POST IT ! 3

Try a mobile Station 8

Making QSL Card 6

[ HAM­MAG N.10 November 2009 ]

Four Radio Amateurs Killed in Plane Crash En Route to

GB7OK D­Star gateway is now live

Sunspot 1029 puts on a show

Keep tabs on ISS with an iPhone

[ HAM­MAG N.10 November 2009 ]

Photo of the finished BOX

[ HAM­MAG N.10 November 2009 ]

[ HAM­MAG N.10 November 2009 ]

How to Make a Custom QSL Card:

From your PC:

73’s – Bill – KA6KBC

Note from F5SLD.

[ HAM­MAG N.10 November 2009 ]

1) Getting adequate 12 DC through the firewall of your vehicle,

3) Common mode (CM): The nemesis of mobile

4) Noise: Electronic nose of a dozen varieties will test your

[ HAM­MAG N.10 November 2009 ]

As anyone who has listened to a receiver suspects, everything in the universe

[ HAM­MAG N.10 November 2009 ]

Pn = kTB = 1.38 x 10­23 x 290 x 2500 = 1.0 x 10­17 watts

Nadded = (k Te1G1G2... GN) + (kTe2G2... GN) + ... + (kTeNGN)

[ HAM­MAG N.10 November 2009 ]

[ HAM­MAG N.10 November 2009 ]

Noise Figure Measurement

[ HAM­MAG N.10 November 2009 ]

Using the Noise Figure Meter

[ HAM­MAG N.10 November 2009 ]

Sky Noise Measurement

Several precautions are necessary:

[ HAM­MAG N.10 November 2009 ]

[ HAM­MAG N.10 November 2009 ]

Homebrew Noise Sources

[ HAM­MAG N.10 November 2009 ]

[ HAM­MAG N.10 November 2009 ]

[ HAM­MAG N.10 November 2009 ]

Noise Source Calibration

Using the noise source

[ HAM­MAG N.10 November 2009 ]

Best 73's N1BWT.

[ HAM­MAG N.10 November 2009 ]

CCF/OHDXF CONTEST & DX CONFERENCE

CE9, SOUTH SHETLAND ISLANDS (Update)

FT5W, CROZET ISLAND

MARCONI NOBEL 100 AWARD

P4, ARUBA (SA­036)

P4, ARUBA (SA­036)

[ HAM­MAG N.10 November 2009 ]

XV, VIETNAM (Update/IOTA Op)

CONTESTS OF THE MONTH

06­07 1200­1200 All Ukrainian DX Contest

[ HAM­MAG N.10 November 2009 ]

­ 1/11 ANTARCTICA; VKØBP AN­016

­ 1/11 ­ 7/11 ARGENTINA; LU/PY2TJ SA­008

­ 2/11 ­ 9/11 UNITED STATES OF AMEICA: KG8DP NA­062

F5SLD's Free HAM Magazine 100% HAM RADIO

[ HAMMAG N.10 November 2009 ]

GB7OK DStar gateway is now live

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

Pn = kTB = 1.38 x 1023 x 290 x 2500 = 1.0 x 1017 watts

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

P4, ARUBA (SA036)

P4, ARUBA (SA036)

[ HAMMAG N.10 November 2009 ]

0607 12001200 All Ukrainian DX Contest

[ HAMMAG N.10 November 2009 ]

1/11 ANTARCTICA; VKØBP AN016

1/11 7/11 ARGENTINA; LU/PY2TJ SA008

2/11 9/11 UNITED STATES OF AMEICA: KG8DP NA062

2/11 23/11 MALI; TZ6JA

3/11 15/11 MONTSERRAT; VP2MUM, VP2MXO and VP2MNK

4/11 11/11 VIRGIN IS; KP2/homecall

4/11 17/11 VIET NAM; XV4D AS128

[ HAMMAG N.10 November 2009 ]

6/11 8/11 EAST MALAYSIA; 9M6DXX/P and 9M6XRO/P OC133

6/11 9/11 VENEZUELA; YW5F SA058

7/11 NIUE; ZK2DL OC040

9/11 PAPUA NEW GUINEA; P2 OC102, OC231 and OC205

11/11 NEW CALEDONIA; FK/F5NHJ OC032 or OC033

10/11 16/11 W. KIRIBATI; T3ØKI and T3ØIW

11/11 13/11 PAPUA NEW GUINEA; P29VCX OC117

11/11 16/11 BRAZIL; PW6C SA062

11/11 18/11 SAMOA; 5W OC097

[ HAMMAG N.10 November 2009 ]

13/11 23/11 COMOROS; D68F AF007

13/11 27/11 GHANA; 9G5TT and 9G5XX AF084

13/11 REPUBLIC OF KOREA; HL9QST

14/11 21/11 FALKLAND IS.; VP8BUG (digital) and VP8BUH (SSB)

15/11 16/11 PAPUA NEW GUINEA; P29VCX OC240

15/11 3/12 TURKS & CAICOS IS.; VP5/homecall NA002

15/11 20/2 2010 ANTARCTICA; KC4USV AN011

[ HAMMAG N.10 November 2009 ]

ca 16/11 LEBANON; OD/W5YFN

17/11 AUSTRALIA; VK7ACG OC006

17/11 30/11 SAMOA; 5WØKH OC097

17/11 15/12 MADAGASCAR; 5R8IC AF090

18/11 24/11 CANADA; VY2/W7ASF NA029

19/11 23/11 NEW CALEDONIA; FK/JA1NLX OC033

19/11 9/12 TONGA; A3 OC049

20/11 26/11 CANADA; VY1RST

20/11 10/2 2010 CANARY ISLANDS; EA8/homecall AF004

21/11 5/12 CHRISTMAS I.; VK9XX OC002

[ HAMMAG N.10 November 2009 ]

23/11 1/12 BOTSWANA; A25NW

23/11 2/12 TUNISIA; 3V3S

23/11 6/12 CHESTERFIELD IS.; TX3A

24/11 1/12 BONAIRE, CURACAO; PJ4/homecall SA006

24/11 6/12 BELIZE; V31PT NA073

25/11 27/11 MARTINIQUE; FM/JE1JKL/p

26/11 1/12 ANTIGUA & BARBUDA; V26K

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

[ HAMMAG N.10 November 2009 ]

HAMMAG N.10 November 2009

Erratum : concerning the photo of the article "Takantenna"