HGTG40N60A4
HGTG40N60A4
HGTG40N60A4
E
Formerly Developmental Type TA49347. C
G
Ordering Information
PART NUMBER PACKAGE BRAND
Symbol
C
FAIRCHILD CORPORATION IGBT PRODUCT IS COVERED BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS
4,364,073 4,417,385 4,430,792 4,443,931 4,466,176 4,516,143 4,532,534 4,587,713
4,598,461 4,605,948 4,620,211 4,631,564 4,639,754 4,639,762 4,641,162 4,644,637
4,682,195 4,684,413 4,694,313 4,717,679 4,743,952 4,783,690 4,794,432 4,801,986
4,803,533 4,809,045 4,809,047 4,810,665 4,823,176 4,837,606 4,860,080 4,883,767
4,888,627 4,890,143 4,901,127 4,904,609 4,933,740 4,963,951 4,969,027
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. Pulse width limited by maximum junction temperature.
TJ = 125oC - - 3.0 mA
Gate to Emitter Threshold Voltage VGE(TH) IC = 250µA, VCE = VGE 4.5 5.6 7 V
Gate to Emitter Plateau Voltage VGEP IC = 40A, VCE = 0.5 BVCES - 8.5 - V
NOTES:
2. Turn-Off Energy Loss (EOFF) is defined as the integral of the instantaneous power loss starting at the trailing edge of the input pulse and ending
at the point where the collector current equals zero (ICE = 0A). All devices were tested per JEDEC Standard No. 24-1 Method for Measurement
of Power Device Turn-Off Switching Loss. This test method produces the true total Turn-Off Energy Loss.
3. Values for two Turn-On loss conditions are shown for the convenience of the circuit designer. EON1 is the turn-on loss of the IGBT only. EON2 is
the turn-on loss when a typical diode is used in the test circuit and the diode is at the same TJ as the IGBT. The diode type is specified in Figure 20.
Typical Performance Curves Unless Otherwise Specified ICE, COLLECTOR TO EMITTER CURRENT (A)
80 225
VGE = 15V TJ = 150oC, RG = 2.2Ω, VGE = 15V, L = 100µH
ICE , DC COLLECTOR CURRENT (A)
70 200
PACKAGE LIMITED
175
60
150
50
125
40
100
30
75
20 50
10 25
0 0
25 50 75 100 125 150 0 100 200 300 400 500 600 700
TC , CASE TEMPERATURE (oC) VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 1. DC COLLECTOR CURRENT vs CASE FIGURE 2. MINIMUM SWITCHING SAFE OPERATING AREA
TEMPERATURE
300 12 1200
TC VGE
200
75oC 15V
10 1000
ISC
100
8 800
fMAX1 = 0.05 / (td(OFF)I + td(ON)I)
fMAX2 = (PD - PC) / (EON2 + EOFF)
6 600
PC = CONDUCTION DISSIPATION
(DUTY FACTOR = 50%)
tSC
RØJC = 0.2oC/W, SEE NOTES
4 400
80 80
DUTY CYCLE < 0.5%, VGE = 12V DUTY CYCLE < 0.5%, VGE = 15V
PULSE DURATION = 250µs PULSE DURATION = 250µs
70 70
60 60
50 50
TJ = 125oC
40 40 TJ = 125oC
30 30
TJ = 25oC
20 20 TJ = 25oC
TJ = 150oC TJ = 150oC
10 10
0 0
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 2.2
VCE, COLLECTOR TO EMITTER VOLTAGE (V) VCE, COLLECTOR TO EMITTER VOLTAGE (V)
FIGURE 5. COLLECTOR TO EMITTER ON-STATE VOLTAGE FIGURE 6. COLLECTOR TO EMITTER ON-STATE VOLTAGE
5500 1800
RG = 2.2Ω, L = 200µH, VCE = 390V
RG = 2.2Ω, L = 200µH, VCE = 390V
EON2 , TURN-ON ENERGY LOSS (µJ)
5000 1600
4500
1400
4000 TJ = 125oC, VGE = 12V, VGE = 15V
1200 TJ = 125oC, VGE = 12V OR 15V
3500
3000 1000
2500 800
2000 600
1500
400
1000
200 TJ = 25oC, VGE = 12V OR 15V
500 TJ = 25oC, VGE = 12V, VGE = 15V
0 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
ICE , COLLECTOR TO EMITTER CURRENT (A) ICE , COLLECTOR TO EMITTER CURRENT (A)
FIGURE 7. TURN-ON ENERGY LOSS vs COLLECTOR TO FIGURE 8. TURN-OFF ENERGY LOSS vs COLLECTOR TO
EMITTER CURRENT EMITTER CURRENT
42 120
RG = 2.2Ω, L = 200µH, VCE = 390V RG = 2.2Ω, L = 200µH, VCE = 390V
td(ON)I, TURN-ON DELAY TIME (ns)
40
TJ = 25oC, TJ = 125oC, VGE = 15V 100
38 TJ = 125oC, TJ = 25oC, VGE = 12V
32 60
30
40
28
26
20
24 TJ = 25oC, TJ = 125oC, VGE = 15V
TJ = 25oC, TJ = 125oC, VGE = 15V
22 0
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
ICE , COLLECTOR TO EMITTER CURRENT (A) ICE , COLLECTOR TO EMITTER CURRENT (A)
FIGURE 9. TURN-ON DELAY TIME vs COLLECTOR TO FIGURE 10. TURN-ON RISE TIME vs COLLECTOR TO
EMITTER CURRENT EMITTER CURRENT
190 70
RG = 2.2Ω, L = 200µH, VCE = 390V RG = 2.2Ω, L = 200µH, VCE = 390V
td(OFF)I , TURN-OFF DELAY TIME (ns)
65
180
TJ = 125oC, VGE = 12V OR 15V
60
tfI , FALL TIME (ns)
170
55
VGE = 12V, VGE = 15V, TJ = 125oC
160 50
45
150
40
VGE = 12V OR 15V, TJ = 25oC TJ = 25oC, VGE = 12V OR 15V
140
35
130 30
0 10 20 30 40 50 60 70 80 0 10 20 30 40 50 60 70 80
ICE , COLLECTOR TO EMITTER CURRENT (A) ICE , COLLECTOR TO EMITTER CURRENT (A)
FIGURE 11. TURN-OFF DELAY TIME vs COLLECTOR TO FIGURE 12. FALL TIME vs COLLECTOR TO EMITTER
EMITTER CURRENT CURRENT
ICE, COLLECTOR TO EMITTER CURRENT (A)
400 16
DUTY CYCLE < 0.5%, VCE = 10V IG(REF) = 1mA, RL = 7.5Ω, TC = 25oC
VGE, GATE TO EMITTER VOLTAGE (V)
200 8
TJ = -55oC TJ = 125oC
150 6 VCE = 200V
TJ = 25oC
100 4
50 2
0 0
6 7 8 9 10 11 0 50 100 150 200 250 300 350 400
VGE, GATE TO EMITTER VOLTAGE (V) QG , GATE CHARGE (nC)
6 100
TJ = 125oC, L = 200µH, VCE = 390V, VGE = 15V TJ = 125oC, L = 200µH
ETOTAL = EON2 + EOFF VCE = 390V, VGE = 15V
5 ETOTAL = EON2 + EOFF
ICE = 80A
4 10 ICE = 80A
3 ICE = 40A
2 ICE = 40A 1
ICE = 20A
1
ICE = 20A
0 0.1
25 50 75 100 125 150 1 10 100 500
TC , CASE TEMPERATURE (oC) RG, GATE RESISTANCE (Ω)
FIGURE 15. TOTAL SWITCHING LOSS vs CASE FIGURE 16. TOTAL SWITCHING LOSS vs GATE RESISTANCE
TEMPERATURE
14 2.4
10
2.2
8
CIES ICE = 80A
6 2.1
ICE = 40A
4
COES 2.0
ICE = 20A
2
CRES
1.9
0 8 9 10 11 12 13 14 15 16
0 10 20 30 40 50 60 70 80 90 100
VCE, COLLECTOR TO EMITTER VOLTAGE (V) VGE, GATE TO EMITTER VOLTAGE (V)
FIGURE 17. CAPACITANCE vs COLLECTOR TO EMITTER FIGURE 18. COLLECTOR TO EMITTER ON-STATE VOLTAGE vs
VOLTAGE GATE TO EMITTER VOLTAGE
ZθJC , NORMALIZED THERMAL RESPONSE
100
0.50
0.20 t1
0.10 PD
10-1
0.05 t2
DUTY FACTOR, D = t1 / t2
0.02
PEAK TJ = (PD X ZθJC X RθJC) + TC
0.01
SINGLE PULSE
10-2 -5
10 10-4 10-3 10-2 10-1 100 101
t1 , RECTANGULAR PULSE DURATION (s)
HGT1Y40N60A4D
90%
VGE 10%
EON2
L = 200µH EOFF
VCE
RG = 2.2Ω
90%
+ ICE 10%
VDD = 390V td(OFF)I trI
- tfI
td(ON)I
FIGURE 20. INDUCTIVE SWITCHING TEST CIRCUIT FIGURE 21. SWITCHING TEST WAVEFORMS
As used herein:
1. Life support devices or systems are devices or systems 2. A critical component is any component of a life support
which, (a) are intended for surgical implant into the body, device or system whose failure to perform can be
or (b) support or sustain life, or (c) whose failure to perform reasonably expected to cause the failure of the life support
when properly used in accordance with instructions for use device or system, or to affect its safety or effectiveness.
provided in the labeling, can be reasonably expected to
result in significant injury to the user.
No Identification Needed Full Production This datasheet contains final specifications. Fairchild
Semiconductor reserves the right to make changes at
any time without notice in order to improve design.
Rev. I5