DEEP SEA ELECTRONICS

DSE2510 MKII & DSE2520 MKII

Configuration Suite PC Software Manual

Document Number: 057-279

Author: Bedig Boghossian

057-279 ISSUE: 1
 DSE2510 MKII & DSE2520 MKII Configuration Suite PC Software Manual

DEEP SEA ELECTRONICS PLC

Highfield House
Hunmanby
North Yorkshire
YO14 0PH
ENGLAND

Sales Tel: +44 (0) 1723 890099

Sales Fax: +44 (0) 1723 893303

E-mail : sales@Deepseaplc.com
Website : www.deepseaplc.com

DSE2510 MKII / DSE2520 MKII Configuration Suite PC Software Manual

© Deep Sea Electronics Plc

All rights reserved. No part of this publication may be reproduced in any material form (including photocopying or
storing in any medium by electronic means or other) without the written permission of the copyright holder except
in accordance with the provisions of the Copyright, Designs and Patents Act 1988.
Applications for the copyright holder’s written permission to reproduce any part of this publication must be
addressed to Deep Sea Electronics Plc at the address above.

The DSE logo is a UK registered trademarks of Deep Sea Electronics PLC.

Any reference to trademarked product names used within this publication is owned by their respective
companies.

Deep Sea Electronics Plc reserves the right to change the contents of this document without prior notice.

Amendments List

Issue Comments
1 Initial release

Typeface: The typeface used in this document is Arial. Care must be taken not to mistake the upper case letter I with the numeral 1. The numeral
1 has a top serif to avoid this confusion.

057-279 ISSUE: 1 Page 2 of 12

 DSE2510 MKII & DSE2520 MKII Configuration Suite PC Software Manual

TABLE OF CONTENTS
1 INTRODUCTION .............................................................................................. 4
1.1 BIBLIOGRAPHY .......................................................................................................................... 4
1.1.1 INSTALLATION INSTRUCTIONS .......................................................................................... 4
1.1.2 MANUALS ............................................................................................................................ 4
1.1.3 CLARIFICATION OF NOTATION........................................................................................... 4
1.1.4 GLOSSARY OF TERMS........................................................................................................ 5
1.2 INSTALLATION AND USING THE DSE CONFIGURATION SUITE SOFTWARE .......................... 5
2 EDITING THE CONFIGURATION.................................................................... 6
2.1 SCREEN LAYOUT ....................................................................................................................... 6
2.2 MODULE OPTIONS ..................................................................................................................... 7
2.2.1 MODULE TIMERS ................................................................................................................ 7
2.2.1.1 MODULE TIMERS............................................................................................................. 7
2.2.1.2 MISCELLANEOUS OPTIONS............................................................................................ 8
2.3 COMMUNICATIONS .................................................................................................................... 9
2.3.1 COMMUNICATIONS OPTIONS............................................................................................. 9
2.3.2 DISPLAY PORT .................................................................................................................. 10
2.3.3 MODBUS PASSTHROUGH PORT ...................................................................................... 11

Page 3 of 12 057-279 ISSUE: 3

 Introduction

1 INTRODUCTION
This document details the DSE2510 MKII & DSE2520 MKII software configuration using the DS Configuration
Suite. The DSE2510 MKII & DSE2520 MKII remote display modules are converted from the DSE7310 MKII &
DSE7320 MKII controllers using a Firmware Update, for more details check the DSE Publication: 057-278
DSE2510 MKII & DSE2520 MKII Operators Manual.

The DSE Configuration Suite PC Software allows the DSE25xx MKII modules to be connected to a PC via
USB A –USB B cable. Once connected the various operating parameters within the module are viewed or edited
as required by the engineer. This software allows easy controlled access to these values.

This manual details the configuration of the DSE2510 MKII & DSE2520 MKII series controllers.
The older DSE2510 and DSE2520 modules configuration are covered in the host controllers’ Software Manuals
supporting the DSEnet port.
The DSE Configuration Suite PC Software must only be used by competent, qualified personnel, as changes to
the operation of the module may have safety implications on the panel / generating set to which it is fitted. Access
to critical operational sequences and settings for use by qualified engineers, may be barred by a security code
set by the generator provider.
The information contained in this manual must be read in conjunction with the information contained in the
appropriate module documentation. This manual only details which settings are available and how they may be
used. A separate manual deals with the operation of the individual module (See section entitled Bibliography
elsewhere in this document).

1.1 BIBLIOGRAPHY
This document refers to and is referred to by the following DSE publications which is obtained from the DSE
website www.deepseaplc.com

1.1.1 INSTALLATION INSTRUCTIONS

DSE PART DESCRIPTION
053-232 DSE2510 MKII & DSE2520 installation instructions sheet
053-181 DSE7310 MKII & DSE7320 MKII installation instructions sheet
053-191 DSE7410 MKII & DSE7420 MKII installation instructions sheet

1.1.2 MANUALS
DSE PART DESCRIPTION
057-151 DSE Configuration Suite PC Software Installation & Operation Manual
057-278 DSE2510 MKII & DSE2520 MKII Operator Manual
057-253 DSE7310 MKII & DSE7320 MKII Operator Manual
057-243 DSE7310 MKII & DSE7320 MKII Software Manual
057-263 DSE7410 MKII & DSE7420 MKII Operator Manual
057-262 DSE7410 MKII & DSE7420 MKII Software Manual

1.1.3 CLARIFICATION OF NOTATION

Clarification of notation used within this publication.

NOTE: Highlights an essential element of a procedure to ensure correctness.

Indicates a procedure or practice, which, if not strictly observed, could

CAUTION! result in damage or destruction of equipment.

Indicates a procedure or practice, which could result in injury to

WARNING! personnel or loss of life if not followed correctly.

057-279 ISSUE: 1 Page 4 of 12

 Introduction

1.1.4 GLOSSARY OF TERMS

Term Description
DSE2510 MKII DSE2510 MKII module/controller converted from the DSE7310 MKII
DSE2520 MKII DSE2520 MKII module/controller converted from the DSE7320 MKII
DSE7xxx MKII All modules in the DSE7xxx MKII range.
DSE7300 MKII,
All modules in the DSE73xx MKII range.
DSE73xx MKII
DSE7310 MKII DSE7310 MKII module/controller
DSE7320 MKII DSE7320 MKII module/controller
DSE7400 MKII,
All modules in the DSE74xx MKII range.
DSE74xx MKII
DSE7410 MKII DSE7410 MKII module/controller
DSE7420 MKII DSE7420 MKII module/controller

1.2 INSTALLATION AND USING THE DSE CONFIGURATION SUITE

SOFTWARE
For information in regards to instating and using the DSE Configuration Suite Software please refer to DSE
publication: 057-151 DSE Configuration Suite PC Software Installation & Operation Manual which is found
on our website: www.deepseaplc.com

Page 5 of 12 057-279 ISSUE: 1

 Editing the Configuration

2 EDITING THE CONFIGURATION

This menu allows module configuration, to change the Slave ID, enabling ports, system timers and options to suit
a particular application.

2.1 SCREEN LAYOUT

Move to the
The type of Previous or Next
configuration file configuration page
being edited

The coloured
shading shows
Close this
the currently
configuration file
selected page.

Click + or – to
show or hide the
sub settings within
each sections.

Step forward or backward through Click to return to this

previously viewed pages page at any time

Click to select
the subsection
to view / edit

057-279 ISSUE: 1 Page 6 of 12

 Editing the Configuration

2.2 MODULE OPTIONS

Select this option to configure the options.

2.2.1 MODULE TIMERS

NOTE: The Sleep Mode is disabled when the DSE25xx MKII remote display module is connected to
the DSE7xxx MKII controller.

2.2.1.1 MODULE TIMERS

Parameter Description
Page If the module is left unattended for the duration of the Page Timer it reverts to
show the Status page.
Scroll The scroll time between parameters on a selected page.
Backlight Power Saving
=Normal operation
 = If the module is left unattended for the duration of the Backlight Power
Saving Timer, the LCD backlight turns off.

Page 7 of 12 057-279 ISSUE: 1

 Editing the Configuration

2.2.1.2 MISCELLANEOUS OPTIONS

Parameter Description
Follow Main Unit
= If any control button is pressed, the host module does not respond.
 = If any control button (Stop, Manual, Auto, Mute / Lamp Test, Start) is
pressed and Control Buttons are enabled, the host module follows the
DSE25xx MKII module.
Sounder Enable
= Disable the DSE2500 MKII module’s internal sounder
 = Enable the DSE2500 MKII module’s internal sounder.
Auto Mute Timer Enable
= Auto Mute is disabled.
 = The internal sounder activates for the duration of the Auto Mute Timer
after which it automatically stops. Pressing the MUTE button during the timer
also silences the sounder.
Control Buttons Enable
= The display is for instrumentation only – the mode change buttons are
disabled.
 = The display acts as a complete mimic/control of the host module.
Remote Panel Lock Enable
= The Remote Panel Lock is disabled.
 = The DSE2500 MKII module is locked when Digital Input A is active.

057-279 ISSUE: 1 Page 8 of 12

 Editing the Configuration

2.3 COMMUNICATIONS
The Communications section is subdivided into smaller sections.
Select the required section with the mouse.

2.3.1 COMMUNICATIONS OPTIONS

NOTE: The DSE2510 MKII & DSE2520 MKII modules DSEnet port are used as RS485 when Display
Port is selected as RS485.

Parameter Description
Display Port The options are :
RS485: The DSE2500 MKII module’s DSEnet is connected to the host controller’s
RS485 port for remote display.
RS232: The DSE2500 MKII module is connected to the host controller through their
RS232 port.
Modbus Passthrough Disabled: MODBUS communication with the host controller through the Remote
Port Display is disabled.
Enabled: The DSE2500 MKII module allows MODBUS communication with its host
controller through the DSE2500 MKII’s RS485 port.

Page 9 of 12 057-279 ISSUE: 1

 Editing the Configuration

2.3.2 DISPLAY PORT

Parameter Description
Slave ID The Slave ID of the DSE2500 MKII port used for the remote display.
Baud Rate The remote display Baud Rate is fixed to 115200 cannot be changed.

057-279 ISSUE: 1 Page 10 of 12

 Editing the Configuration

2.3.3 MODBUS PASSTHROUGH PORT

Parameter Description
Slave ID Factory Setting: 10
The Modbus Slave ID of the DSE2500 MKII RS485 port for Modbus Passthrough.
This is the RS485 Slave ID that is used by the Modbus Master device used to query the
host controller connected to the DSE2500 MKII. Modbus Requests sent to this address
are relayed (Passthrough) to the DSE host controller connected to the DSE2500 MKII.
Baud Rate Factory Setting: 115200
Baud rate of the RS485 port.
Iner-frame delay Set the time delay between a MODBUS RTU request and the receipt of a response.

Page 11 of 12 057-279 ISSUE: 1

This Page Intentionally Blank