Eppendorf Xplorer® – Short instructions Eppendorf Xplorer® – Short instructions

Dis and Ads modes = Dispensing and Automatic dispensing These short instructions are a supplement to the operating manual and not a substitute.
Read the operating manual before using the Xplorer for the first time!
Procedure These short instructions are valid from software version 01.05.00
In the Dis and Ads modes the aspirated liquid is dispensed in
defined individual steps.
Front view of upper part
The display shows the volume per step and the total number of
individual steps (Steps).
The Ads mode also shows the delay between the dispensing steps 1 Selection dial
(Time).

Ads
s
Di 1 The arrow indicates the selected mode.
In the Ads mode the rocker is held down to perform all dispensing Off 2
Pip Available modes:
steps. Automatic dispensing may be interrupted by releasing the M
P/ Ads = Automatic dispensing

Man

Opt
rocker.
Dis = Dispensing
Aspiration 1. Press the rocker up. Pip = Pipetting
P/M = Pipetting and Mixing
Man = Manual pipetting
Opt = Options
3 Off = Power off

Reverse stroke After aspiration the reverse Edit Help

2 Red hardware reset button
after aspiration stroke must be discarded. 3 Display
2. Press the rocker down. The display shows the selected mode, the set volume, as
4
well as the aspiration and dispensing speed. The Counter
counts each finished dispensing step in the Pipetting
mode.*
Before the first 3. Press the rocker down for
dispensing step the first dispensing step. The display dims during usage intervals and switches off
5 after prolonged usage intervals.
In the Ads mode the rocker
is held down. 4 Softkeys
1 2 3 4 5 The softkeys have variable functions. The active functions
are shown in the bottom line of the display on both the left
Before the 4. Press the rocker down
and right sides.
second again. 6
Press the Help softkey for additional information.
dispensing step
5 Rocker
1 2 3 4 5 The rocker is used to move the piston during dispensing
operations.
Hint During the editing procedure the selected parameter will be
To abort the Dis or Ads modes press the Empty softkey to empty liquid from the tip. changed.
eppendorf® is a registered trademark.

When all 5. Press the rocker up to Power on: 6 Ejector

dispensing steps aspirate liquid again.  Press the rocker or a softkey. Press the ejector to eject the pipette tip. Pressing the
are finished: Or:  Then select a mode. ejector when the tip is filled moves the piston to the basic
position.*
1. Security step: Press the
4861 900.024-01/0610

rocker down once. * This feature can be switched off or on in the options.

2. Press the rocker down again

to discard the residual liquid
in the tip.
3. Eject the tip.
In touch with life
Your local distributor: www.eppendorf.com/worldwide
Eppendorf AG · Hamburg · Germany · Tel: +49 40 538 01-0 · Application Support E-mail: support@eppendorf.com
Eppendorf North America, Inc. · USA · Tel: +1 800 645 3050, menu option 2 · E-mail: techserv@eppendorf.com
 Eppendorf Xplorer® – Short instructions Eppendorf Xplorer® – Short instructions

Option: Language selection Edit Pipetting mode (Pip) Pipetting mode (Pip) Pipetting and Mixing mode (P/M)

The language English is set by default on delivery. Procedure Procedure

1. Turn the selection
Aspiration and dispensing are performed like in the

Ads
1. Turn the selection Di
dial to Pip. Aspiration 1. Press the rocker up.
Pip s
P/M

Pip mode. Mixing occurs automatically after the

Di
M Off
dial to Opt.
an
s Pip
Ads M
Opt P/

Man
liquid has been dispensed.

Opt
Before
Off

Piston in basic
2. Select the Language The display also shows the
position.
option with the mixing volume (Mix) and the
rocker. 2. Press the Edit number of mixing cycles
softkey. (Cycles).
3. Open the Language
option with the
Select softkey. 3. Select the volume
After If the rocker is held down during mixing, mixing
4. Select your with the rocker.
occurs until the rocker is released. After mixing, the
language with the Dispensing 2. Press the rocker down.
Blow step (Blow) must be performed.
rocker. 4. Press the Next
Before
softkey to select the
5. Open your language Stopping the mixing process:
next parameter. Press the rocker up to stop the mixing
with the Select
5. Select the aspiration process.
softkey.
speed with the
The number of Hint
rocker.
languages available Editing the pipetting volume automatically
depends on the 6. Press the Next
changes the mixing volume.
software version. softkey to select the
After The mixing volume can be edited
next parameter.
6. To change the separately after pressing the Next softkey
7. Select the Blow 3. Press the rocker down.
to reach the Mix parameter.
language, press the
Yes softkey. dispensing speed Before
with the rocker. Manual pipetting mode (Man)
8. Press the Next
softkey to select the Procedure
The new language next parameter.
is activated. The Manual pipetting procedure
Optional parameter: is the equivalent of operation
Counter indicates with a mechanical piston-stroke
the number of pipette:
performed After
dispensing steps. Edit Help

9. Select the new Repeat Blow or Next aspiration – Liquid is aspirated as long as the rocker is
Hint
Turn the selection dial to exit the options. number with the pressed up.
rocker. – Piston movement stops when the rocker is
Hint: Adjustment 10.Press the End released.
A wrench in the left part of the header softkey to save the – Liquid is dispensed as long as the rocker is held
Press the rocker Press the rocker up
indicates that the factory setting has been changes and to exit down.
down
changed. the edit mode. – Piston movement stops when the rocker is
No symbol appears in the header if the The pipette is ready Hint for the Pip and Dis modes: released.
factory setting is active. for aspiration with Stopping the piston movement! – After each stop, the direction of piston movement
new parameters. Press the rocker in the other direction to can be changed.
stop the piston movement. Restart the – During use, the display always shows the current
piston movement by pressing the rocker volume in the tip. The Max line shows the
up or down. maximum aspiration volume selected during the
editing procedure.
The editing procedure is the same in all operating
modes.