DRO PROS

SIEG SC8 BENCH LATHE

INSTRUCTION MANUAL

FOR YOUR OWN SAFETY, PLEASE

READ THE ENTIRE MANUAL BEFORE USING
1
2
 Table of Contents

SC8 Lathe Parameters ........................................................................................................................ 5

SECTION 1: SAFETY ..................................................................................................................... 7
SECTION 2: POWER SUPPLY ..................................................................................................... 9
Circuit Requirements .......................................................................................................................... 9
SECTION 3: SETUP ...................................................................................................................... 11
Unpacking ........................................................................................................................................ 11
Inventory .......................................................................................................................................... 11
Clean Up ........................................................................................................................................... 11
Installation Dimensions .................................................................................................................... 12
SECTION 4: NORMAL OPERATIONS ..................................................................................... 13
Controls ............................................................................................................................................ 13
Lathe Test Run ................................................................................................................................. 14
Removing the Chuck ........................................................................................................................ 14
Installing the Chuck.......................................................................................................................... 15
Dead Centers .................................................................................................................................... 16
Changing Tool Posts ........................................................................................................................ 17
Cross Slide ........................................................................................................................................ 17
Compound Slide ............................................................................................................................... 18
Carriage Handwheel ......................................................................................................................... 18
Half Nut Lever.................................................................................................................................. 18
Carriage / Cross Feed Lever ............................................................................................................. 18
Carriage Lock ................................................................................................................................... 19
Gearbox Dials ................................................................................................................................... 19
Threads and Change Gears ............................................................................................................... 19
Left Threads and Reverse Cutting Feed ........................................................................................... 21
Clutch Overload ............................................................................................................................... 21
SECTION 5: MAINTENANCE .................................................................................................... 22
Lubrication ....................................................................................................................................... 22
Gearbox Oil Reservoir...................................................................................................................... 23
Wiring Diagram ................................................................................................................................ 25
Parts List ........................................................................................................................................... 26
3
 Identification
The following is a list of controls and components on the lathe. Please take the time to
become familiar with each item and its location. These terms will be used throughout the
manual and knowing them is essential to understanding the instructions and terminology
used in this manual.

1. Thread Pitch Gearing & Speed Charts 13. Half Nut Lever
2. Emergency Stop Switch 14. Carriage/Cross Feed Lever
3. Speed Regulation 15. Tailstock Barrel Handwheel
4. Lathe or Drill Change Switch 16. Tailstock Clamp Bolt
5. Lathe Start Button 17. Tailstock Center Lock
6. Lathe Stop Button 18. Compound Slide Handwheel
7. Gear Box 19. Cross Slide
8. Clutch Overload 20. Tool Post
9. Lathe Chuck 21. Carriage
10. Stop Plate 22. Headstock Eye Shield
11. Carriage Handwheel 23. Speed Display
12. Cross Slide Handwheel 24. Lathe Forward/Reverse Button

4
 SC8 Lathe Parameters
Product Dimensions:

Weight ....................................................................................................................................... 205 kg

Width (side-to-side) x Depth (front-to-back) x Height ............................................ 140 x 53 x 44cm
Footprint (Length x Width) ........................................................................................... 140 x 15.5 cm

Shipping Dimensions:

Type .................................................................................................................................. Wood Crate

Content .................................................................................................................................. Machine
Weight ....................................................................................................................................... 245 kg
Length x Width x Height .......................................................................................... 156 x 68 x 61.cm

Electrical:

Minimum Circuit Size .................................................................................................. 20 amp (110v)

Switch ...................................................................................................................... Forward/Reverse

Motor Specifications:

Type ................................................................................................................................ W122-1500C

Output power ............................................................................................................................ 1500W
Amps ............................................................................................................................ 15 amp (110v)
Speed ............................................................................................................................. 200-3500 rpm
Speeds.................................................................................................................................... Variable
Power Transfer ...................................................................................................... Belt Drive to Gear
Bearings .................................................................................. Shielded and Permanently Lubricated

Travel Specifications:

Swing Over Bed ......................................................................................................................280 mm

Distance Between Centers .......................................................................................................750 mm
Swing Over Cross Slide ............................................................................................................85 mm
Swing Over Saddle ..................................................................................................................105 mm
Maximum Tool Bit Size ............................................................................................................14 mm
Compound Travel ......................................................................................................................80 mm
Carriage Travel ........................................................................................................................650 mm
Cross Slide Travel ...................................................................................................................155 mm

Headstock Info:

Spindle Bore ..............................................................................................................................25 mm

Spindle Size ...........................................................................................................................Φ54 mm
Spindle Taper ............................................................................................................................. MT#4
Number of Spindle Speeds ..................................................................................................... Variable
Spindle Speeds .............................................................................................................. 100-2000 rpm
Spindle Type ............................................................................................................................. Flange
5
Spindle Bearings ................................................................................. Tapered Roller + Ball Bearing

Tailstock Info:

Tailstock Quill Travel ...............................................................................................................60 mm

Tailstock Taper ........................................................................................................................... MT#2
Tailstock Barrel Diameter .....................................................................................................Φ30 mm

Metric Lathe Threading Specs:

Number of Longitudinal Feeds ........................................................................................................ 14

Range of Longitudinal Feeds ........................................................................................0.03 – 0.3 mm
Number of Cross Feeds .................................................................................................................... 14
Range of Cross Feeds ................................................................................................0.015 – 0.15 mm
Number of Inch Threads .................................................................................................................... 6
Range of Inch Threads ...................................................................................................... 12 - 80 TPI
Number of Metric Threads ............................................................................................................... 15
Range of Metric Threads ............................................................................................... 0.25 - 2.5 mm

Imperial Lathe Threading Specs:

Number of Longitudinal Feeds ........................................................................................................ 15

Range of Longitudinal Feeds ..................................................................................... 0.0016 – 0.015”
Number of Cross Feeds .................................................................................................................... 15
Range of Cross Feeds ............................................................................................... 0.0008 – 0.0061”
Number of Inch Threads .................................................................................................................. 21
Range of Inch Threads ........................................................................................................ 5 - 72 TPI
Number of Metric Threads ............................................................................................................... 12
Range of Metric Threads .................................................................................................... 0.5 - 4 mm

Dimensions:

Bed Width ...............................................................................................................................155 mm

Leadscrew Diameter ................................................. 20 mm (Metric Lathe) / 3/4 in (Imperial Lathe)
Leadscrew.................................................................... 3 mm (Metric Lathe) / 8 TPI (Imperial Lathe)
Leadscrew Length .................................................................................................................1069 mm
Steady Rest Capacity ........................................................................................................... 6 - 50 mm
Follow Rest Capacity .......................................................................................................... 6 - 50 mm
Faceplate Size ......................................................................................................................Φ240 mm
Floor to Center Height.............................................................................................................348 mm

Construction:

Headstock .............................................................................................................................. Cast Iron

Headstock Gears ........................................................................................................................... Steel
Bed ....................................................................................................... Induction Hardened Cast Iron
Body ...................................................................................................................................... Cast Iron
Paint ........................................................................................................................................... Epoxy
6
 SECTION 1: SAFETY
READ THE ENTIRE MANUAL 7. Make sure switches are in the OFF
BEFORE OPERATING LATHE. position before connecting power to the
FAILURE TO FOLLOW machine.
INSTRUCTIONS CAN RESULT
IN PERSONAL INJURY
AND/OR DEATH. 8. Keep work area clean, free of clutter,
grease, etc.

Safety Instructions 9. Keep children and visitors away. Visitors

must be kept at a safe distance while operating
1. Thoroughly read the Instruction Manual the unit.
before operating your lathe. Learn the
applications, limitations and potential hazards 10. Childproof your workshop with padlocks,
of this machine. Keep the manual in a safe and master switches or by removing starter keys.
convenient place for future reference.
11. Stop and disconnect the machine when
2. Keep work area clean and well lighted. cleaning, adjusting or servicing.
Clutter and inadequate lighting invite potential
hazards. 12. Do not force tools. The machine will do a
safer and better job at the rate for which it was
3. Ground all tools. If a machine is equipped designed.
with a three-prong plug, it must be plugged
into a three-hole grounded electrical receptacle 13. Use the correct tool. Do not force the
or grounded extension cord. If using an adapter machine or attachment to do a job for which it
to aid in accommodating a two-hole receptacle, was not designed.
ground using a screw to a known ground.
14. Wear proper apparel. Never wear loose
4. Wear eye protection at all times. Use clothing, neck ties, gloves or jewelry. Secure
safety glasses with side shields or safety long hair away from moving parts.
goggles that meet the appropriate standards of
the American National Standards Institute 15. Remove adjusting keys, rags, and tools.
(ANSI). Before turning the machine on, make it a habit
to check that all adjusting keys and wrenches
5. Avoid dangerous environments. Do not have been removed.
operate this machine in a wet or open flame
environment. Airborne dust particles constitute 16. Avoid using an extension cord. But if you
an explosion and fire hazard. must use one, examine the extension cord to
ensure it is in good condition. Immediately
6. Ensure all guards are securely in place replace a damaged extension cord. Always use
and in working condition. an extension cord that uses a ground pin and
7
connected ground wire. Use an extension cord Always follow lubrication and accessory
that meets the amp rating on the motor attachment instructions in the manual.
nameplate. If the motor is dual voltage, be sure
to use the amp rating for the voltage you will 21. If at any time you are experiencing
be using. If you use an extension cord with an difficulties performing the intended operation,
undersized gauge or one that is too long, stop the machine! Contact technical support or
excessive heat will be generated within the consult a qualified expert as to how the
circuit, increasing the chance of a fire or operation should be safely performed.
damage to the circuit.
22. Habits—good and bad—are hard to
17. Keep proper footing and balance at all break. Develop good habits in your shop and
times. safety will become second-nature to you.

18. If used, lock your mobile base to prevent 23. Metal shavings, cutting fluids and
the machine from moving during machining associated fumes may be hazardous and
operations. cause an allergic reaction in people and/or
animals. Familiarize yourself with the inherent
19. Never leave the machine unattended. risks involved with metal work and take
Wait until it comes to a complete stop before appropriate precautions to protect yourself and
leaving the area. others.

20. Perform machine maintenance and care.

- WARNINGS -

It is critical that you make sure there is oil in the feed rate gearbox before turning the lathe on. Refer
to the Lubrication instructions on page 23 for more details on which type of oil to use, how much to
use, and where to put it.

The half nut lever should only be engaged for threading operations, not machining.

The clutch stop is not designed to stop carriage movement when the half nut lever is engaged.
Attempting to use the clutch overload system to stop carriage movement while threading, or when
the half nut lever is engaged, WILL cause extensive damage to the lathe.

The carriage lock bolt must be loosened before attempting to move the carriage manually or with
power feed. Not loosening this bolt, before engaging the carriage feed or the half nut lever, will cause
extensive damage to the lathe.

8
 SECTION 2: POWER SUPPLY
Before installing the machine, consider the length of time, damage, overheating, or fire
availability and proximity of the required may result—especially if connected to an
power supply circuit. If an existing circuit does undersized circuit. To reduce the risk of these
not meet the requirements for this machine, a hazards, avoid overloading the machine during
new circuit must be installed. To minimize the operation and make sure it is connected to a
risk of electrocution, fire, or equipment power supply circuit that meets the
damage, installation work and electrical wiring requirements in the following section.
must be done by a qualified electrician in
accordance with all applicable codes and
standards. Circuit Requirements

This machine is prewired to operate on a 110

volt power supply circuit that has a verified
ground and meets the following requirements:

Voltage…………………………..110V/120V
Frequency……………………………..60 Hz
Phase…………………………..Single-Phase
Power Supply Circuit……………..20 Amps

Full-Load Current Rating A power supply circuit includes all electrical

equipment between the breaker box or fuse
The full-load current rating is the amperage a panel in the building and the machine. The
machine draws at 100% of the rated output power supply circuit used for this machine
power. On machines with multiple motors, this must be sized to safely handle the full-load
is the amperage drawn by the largest motor or current drawn from the machine for an
sum of all motors and electrical devices that extended period of time. (If this machine is
might operate at one time during normal connected to a circuit protected by fuses, use a
operations. time delay fuse marked D.)

Full-Load Current Rating at 110V is 20

Amps

The full-load current is not the maximum amount

of amps that the machine will draw. If the
machine is overloaded, it will draw additional
amps beyond the full-load rating. Note: The circuit requirements listed in this
manual apply to a dedicated circuit—where
If the machine is overloaded for a sufficient only one machine will be running at a time. If
9
this machine will be connected to a shared with this machine. If you must use an
circuit where multiple machines will be extension cord, only use it if absolutely
running at the same time, consult a qualified necessary and only on a temporary basis.
electrician to ensure that the circuit is properly Extension cords cause voltage drops, which
sized for safe operation. may damage electrical components and
shorten motor life. Voltage drops increase as
the extension cord size gets longer and the
Grounding & Plug gauge size gets smaller (higher gauge numbers
indicate smaller sizes). Any extension cord
Requirements used with this machine must contain a ground
wire, match the required plug and receptacle,
This machine MUST be grounded. In the event and meet the following requirements:
of certain malfunctions or breakdowns,
grounding reduces the risk of electric shock by Voltage………………………..100V-120V
providing a path of least resistance for electric Minimum Gauge Size..................12 AWG
current. This machine is equipped with a Maximum Length ............................ 50 ft.
power cord that has an equipment-grounding
wire and a grounding
matching receptacle(outlet) that is properly
installed and grounded in accordance with all
local codes and ordinances.

Improper connection of the equipment-

grounding wire can result in a risk of electric
shock. The wire with green (or green-yellow)
insulation is the equipment-grounding wire. If
repair or replacement of the power cord or
plug is necessary, do not connect the
equipment-grounding wire to a live (current
carrying) terminal. Check with a qualified
electrician or service personnel if you do not
understand these grounding requirements, or if
you are in doubt about whether the tool is
properly grounded. If you ever notice that a
cord or plug is damaged or worn, disconnect it
from power, and immediately replace it with a
new one.

Extension Cords

We do not recommend using an extension cord

10
 SECTION 3: SETUP
This machine presents serious injury hazards them; or for the sake of expediency,
to untrained users. Read through this entire replacements can be obtained at your local
manual to become familiar with the controls hardware store.
and operations before starting the machine!
Inventory:
Wear safety glasses during the entire setup A. Lathe ........................................................ 1
process! B. 3-Jaw Chuck 130mm .............................. 1
C. 3-Jaw Chuck Key ................................... 1
The SC8 lathe is a heavy machine. Serious D. Dead Center MT #4................................ 1
personal injury may occur if safe moving E. External Jaws for 3-Jaw Chuck ............ 3
methods are not used. To be safe, get F. Dead Center MT #2 ................................ 1
assistance and use power equipment rated for G. Change Gears 35, 50, 60T (Imp only) .. 1
at least 750 lbs. to move the shipping crate Each
and remove the machine from the crate. H. Hex wrenches 3, 4, 5, 6, 8mm ...... 1 Each
I. Wrenches 8/10, 12/14, 17/19m ...... 1 Each
Unpacking J. V-Belt O-813 ............................................ 1
Your machine was carefully packaged for K. Oiler......................................................... 1
safe transportation. Remove the packaging L. Spindle Wrench ...................................... 1
materials from around your machine and M. Steady Rest Wrench .............................. 1
inspect it. N. Stopping Plate ......................................... 1
O. Clutch Stopping Block ........................... 1
Save the containers and all packing materials
for possible inspection by the carrier or its
agent. Otherwise, filing a freight claim can
be difficult.

When you are completely satisfied with the

condition of your shipment, inventory the
contents.

Figure 1 - Inventory

Note: The 3 Jaw Chuck, 3 Jaw Chuck Key, 3

Jaw Chuck External Jaws, and Clutch
Stopping Block are not pictured in Figure 1.
Inventory
The following is a description of the main Clean Up
components shipped with your machine. Lay
the components out to inventory them. The unpainted surfaces are coated with a
waxy oil to prevent corrosion during
If any non-proprietary parts are missing (e.g. shipment. Remove this protective coating
a nut or a washer), we will gladly replace with a solvent cleaner or degreaser. For
thorough cleaning, some parts must be

11
removed. For optimum performance, clean
all moving parts or sliding contact surfaces.
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner that may
damage painted surfaces. Always follow the
manufacturer’s instructions when using any
type of cleaning product.

WARNING
The pulleys must be clean and free of oil,
otherwise slipping of the belt will cause
damage to the motor.

Installation Dimensions
Please see Figure 2 for the spacing and
location of the lathe mounting holes. Please
use a minimum of M12 or ½” bolts to secure
the lathe.

12
 SECTION 4: NORMAL OPERATIONS
General
Emergency
Speed + Speed -
3The SC8 lathe will perform many types of Stop Switch
operations that are beyond the scope of this
manual. Many of these operations can be
dangerous or deadly if performed incorrectly.
RPM
The instructions in this section are written
with the understanding that the operator has
the necessary knowledge and skills to operate Forward
this machine. If at any time you are
experiencing difficulties performing any Reverse
operation, stop using the machine!

If you are an inexperienced operator, we

strongly recommend that you read books,
trade articles, or seek training from an
experienced lathe operator before performing
Drill / Lathe Start Stop
any unfamiliar operations. Above all, your
Switch
safety should come first!
Figure 3 – Main Lathe Controls

Controls
To get the most out of your machine, please Figure 4 - Compound Slide
take the time to familiarize yourself with the
Note: The "Milling/Drilling" option at the
various controls and components shown in
selector switch is intended for the optional
Figures 3 and 4.
installation of a milling attachment which is
sold separately. Please contact an authorized
dealer for more information.

13
Lathe Test Run 11. Press the “Stop” button.

12. After the chuck has come to a complete

It is critical that you make sure there is oil
stop, press the “Forward” button.
in the feed rate gearbox before proceeding
with the test run. Refer to the Lubrication 13. Allow the lathe to run for at least two full
instructions on page 23 for more details on minutes to make sure it is running
which type of oil to use, how much to use, satisfactorily and the chuck is turning
and where to put it. counterclockwise.
Before operating the lathe, a test run must be 14. Press the “Stop” button.
completed to ensure the lathe operates
properly. 15. After the lathe has come to a complete
stop, engage the carriage handwheel, rotate
1. Put on safety glasses! the handwheel to center the carriage on the
bed, then disengage the handwheel.
2. Ensure the chuck key is NOT inserted in
the chuck, and that the lathe chuck guard is in 16. Engage the automatic carriage feedlever.
the down position. Make this step a habit that
you perform every time you start the lathe. 17. Turn the lathe ON.
3. Familiarize yourself with the lathe controls 18. Verify that the carriage moves along the
shown in Figure 3. Make sure the bed, then press the emergency stop button to
EMERGENCY STOP SWITCH is turn the lathe OFF.
disengaged before continuing.
19. Disengage the feed lever.
4. Clear all tools, components, packing
material, etc. away from the cutter head.
Removing the Chuck
5. Disengage the carriage feed lever.
The SC8 spindle nose mounting system uses
6. Disengage the half-nut lever. a circular lock plate with slotted holes that
are oversized at one end (keyholes). When
7. Plug the machine into the power outlet. the lock plate is rotated counterclockwise (as
facing the chuck), the studs with mounting
8. Rotate the lathe/mill selector switch to the nuts can pass through the spindle nose. When
#1 or “lathe” position. The blue RPM control the lock plate is rotated toward the back of
panel should light up. the lathe, the oversized holes narrow to the
size of the studs, allowing the mounting nuts
9. Stand to the side of the chuck, and press to be tightened against the back of the lock
the green “Start” button. If the carriage plate, thus, securing the chuck or faceplate.
begins moving, immediately push the red
STOP button, disengage the offending feed To remove a chuck or faceplate from the
lever, and restart the lathe. lathe spindle nose, first:

10. Allow the lathe to run for at least two full 1. DISCONNECT POWER FROM THE
minutes to make sure it is running LATHE!
satisfactorily and the chuck is turning
clockwise. 2. Move the lathe chuck guard away from the
chuck.
14
3. Familiarize yourself with the spindle nose
components shown in Figure 5:

Note: The tolerances are tight, so you may

need to tap the chuck/faceplate with a rubber
mallet, rotate it 1⁄4 of a turn, tap it, rotate it,
Figure 5 - Spindle nose components. and continue repeating this process until the
chuck comes out.
4. Place a piece of plywood over the bed-
ways to protect your hands. Never use a pry bar or steel hammer to
remove the chuck or you will damage the
5. Hold the chuck/faceplate with your hand lathe components!
or a chuck key, and using a 17mm wrench,
loosen the three chuck mounting nuts on the Installing the Chuck
back of the knurled lockplate. DO NOT back
the nuts out all the way or they will scratch 1. BEFORE CONTINUING DISCONNECT
the metal cover when you rotate the chuck. THE POWER SOURCE FROM THE LATHE!

6. Rotate the lock plate toward the front of 2. Insert the three mounting studs into the
the lathe. back of the chuck and tighten them down. If
you are switching chucks, take the mounting
7. Remove the chuck/faceplate from the studs out of the previously removed chuck
spindle nose by pulling it out: and use them in the chuck you are going to
install. Also, make sure that a chuck
mounting nut is on each of the studs.

3. Make sure that the knurled lock plate is

rotated all the way toward the front of the
lathe.

4. Insert the chuck onto the spindle nose.

5. Rotate the knurled lock plate toward the

back of the lathe until it stops. If the lock
plate will NOT rotate more than a fraction of
an inch, then the chuck is not completely
inserted. Make sure the chuck is completely
15
inserted so the lock plate can be rotated 1. Use the tailstock handwheel to move the
properly. tailstock quill all the way back into the
tailstock until the handwheel will no longer
6. Hold the chuck/faceplate with your hand turn (this will push the dead center out of the
or a key. Using a 17mm wrench, snug the quill).
three chuck mounting nuts to the back of the
knurled lock plate, then tighten all three with 2. Pull the dead center out of the tailstock
an even pressure. quill.

7. Remove all wrenches and chuck keys from Tailstock Positioning

the chuck/spindle nose.

8. Move the lathe chuck guard down over the Longitudinal Position
chuck before operating, or the lathe will not
To adjust the tailstock longitudinally, follow
start.
these steps:

Dead Centers 1. Loosen the tailstock lock lever shown in

Figure 9.
Follow these steps to install the tailstock
dead center: Tailstock Lock Lever Lateral Offset Index
1. Familiarize yourself with the tailstock
components shown in Figure 7.

Handwheel

Quill Lock

Quill

Lateral Offset Adj. Screw (both sides)

Figure 9 - Tailstock positioning controls.

Figure7 - Tailstock components.
2. Slide the tailstock into position along the bed,
2. Make sure the dead center and tailstock then tighten the lever to secure the tailstock in the
quill are clean and free of any dirt, dust, new position.
grease, or oil. Morse tapers will not interlock
when dirt or oil are present on the mounting Offset Position
surfaces.
The two offset adjustment screws (Figure 9)
position the tailstock adjacent to the center line
3. Extend the quill approximately 1".
for turning tapers.
4. Slide the dead center into the tailstock
To offset the tailstock to the left of the center
quill. line, follow these steps:
To remove the tailstock dead center, 1. Loosen the tailstock lock lever.
follow these steps:
16
2. Using a 6mm hex wrench, loosen the lateral
offset adjustment screw opposite to the direction
you want to move the tailstock.

3. Using a 6mm hex wrench, tighten the lateral

offset adjustment screw on the side of the
direction you want to move the tailstock.

4. Tighten the tailstock lock lever.

Changing Tool Posts

To change the tool post from the compound
rest, follow these steps: Figure 11 - Optional quick change tool post
installed.
1. Rotate the tool post lock handle .
counterclockwise to remove it as in Figure 10.
To adjust the cross slide, follow these steps:

1. Using the handwheel, back the cross slide

away from your starting point by at least 0.015",
then move the cross slide forward to your starting
point.

Note: This procedure will clear any free

movement (or backlash) in the lead screw so your
handwheel scale reading will be accurate.

2. Hold the handwheel still and turn the scale so

the “0” mark lines up with the “0.000” mark on
the cross slide, as shown in Figure 12. As long as
you avoid backlash by continuing to move the
Figure 10 - Removing tool post lock handle. cross slide in the same direction, the scale on the
handwheel will be accurate.
2. Pull the installed tool post straight up to
remove it from the compound slide.

3. Install the new tool post on the compound slide,

and position it to the intended working angle.

4. Tighten the tool post in place with the lock

handle correctly installed.

Cross Slide
The cross slide moves perpendicular to the
longitudinal axis and features a scale on the
handwheel that displays graduations of one Figure 12 - Adjusting the graduated dial.
thousandths of an inch (0.001") or 0.025mm 3. After backing the cross slide away from the
workpiece, remember to clear the backlash before

17
moving th he cross slidee forward to the “0” mark
k
for the nex
xt cut. 5. L
Loosen the ccompound caap screws shown in
ure 13 to movve the compoound fore andd aft.
Figu
Comp
pound Slide
Caarriage Handwh
heel
Similar too the cross slide,
s the com mpound slide
features a scale that displays gradu uations of one Thee carriage hanndwheel (Figgure 14) movves the
thousandthhs of an incch (0.001") or 0.025mm m. carrriage left or rright along thhe bed. This manual
Unlike thee cross slide, the compoun nd slide can be conttrol is necesssary when settting up the mmachine
rotated to a set angle and then it canc be moved d for tturning or whhen manual m movement is desired
back and forth
f along th
he axis of thatt angle. duriing turning opperations.

To adjustt the compou

und slide, do these steps:
Haalf Nut L
Lever
1. Loosen n the compou und bolts sho
own in Figure
13 to allow
w it to be rotaated. For all power feeed operationss, move the hhalf nut
leveer to the righht as shown bbelow in Figu
ure 14.
2. Rotate the compoun
nd slide to thee angle needed
d For threading ooperations, thhe lever shoould be
for your procedure.
p movved to the leeft. The leftt position sshould
onlyy be engageed while cuttting thread
ds.
3. Tightenn the compou
und slide bollts, and check
k
d not move
the angle again to maake sure it did
during tigh
htening.

4. Use thhe compound slide handw wheel to move left rigght

the tool back and forth
h along the ax
xis of the new
w
angle. Siimilar to ad djusting the cross slide Figure 144
handwheeel, make sure the threads arre engaging

Caarriage//Cross F
Feed Levver
Powwer feed for the carriagee and cross sslide is
conttrolled by thhe carriage/crross feed leveer. The
kno b is first rottated to selecct either carrriage or
crosss slide poweer feed, and tthen raised too select
carrriage feed, oor lowered too engage thee cross
slidee power feed. (Figure 15).

Figure 13 - Looseniing the com mpound slide

bolts and compound cap c screws. U
Up Dow
wn
and all baacklash has been cleared before
b you seet
the handw wheel scale to “0”, or itt will not be Figure 155
accurate.
18
Carriage Lock It is best to only change the gearbox dials
when the spindle speed is lower than 660
rpm. When working with spindle speeds
above 660 rpm, it is best to turn the
machine off (or at least allow the spindle
speed to decrease below 660 rpm), before
selecting a different setting.

Use the feed rate charts shown in Figure 18 and

Figure 19 to position the quick change gearbox
levers.

Threads and Change Gears

The Metric version of the SC8 lathe can cut 14
Figure 16 - Carriage controls. metric threads and 6 imperial threads.
The carriage is supplied with a lock bolt on the The Imperial version of the SC8 lathe can cut 15
front right-hand side of the saddle (see imperial and 6 metric threads without changing
Figure 16). This bolt locks the carriage in place gears. Changing gears allows the imperial lathe to
for increased rigidity when making facing cuts. cut an additional 6 imperial and 6 metric threads,
This lock bolt must be loosened before for a total of 33 different thread types. When you
attempting to move the carriage manually receive the machine, the default change gear
or with the power feed. Not loosening this combination is Z30/Z91/Z90. See Figure 20.
bolt before engaging the carriage feed or
the half nut lever will cause extensive Three gears were added to the imperial lathe
( Z35, Z50, and Z60 ) for increased versatility. If
damage to your lathe!
you configure the change gears as shown in the
chart in Figure 19, you can get an extra 6 metric
Gearbox Dials threads and 5 imperial threads screw as Form 1
by changing between Z30 Z35 Z50 Z60 based
The two dials at the bottom of the headstock on thread pitch.
change the feed rate, or the number of threads cut
per-inch (or per mm for metric lathes). The left- Please use Fwd and Rev when cutting thread.
hand dial engages in numeric positions 1, 2, 3, 4,
It’s advisable to adjust the speed to 125 rpm
when thread cutting, and maintain a screw relief
groove of at least three times greater than the
screw pitch. For example, if the screw pitch
is 1.5 mm, the screw relief groove should not be
less than 4 mm. As you become familiar with the
machine and threading operations, you can
change the machine speed or reduce the width of
the relief groove as you see fit.

Figure 17
and 5, while the right-hand dial engages in
positions A, B and C.
19
Figure 18 - Imperial cha
art

Figu
ure 19 - Metrric chart

20
 threeads or need tto reverse thee cutting feed simply
loossen Screw 1 aand rotate Geear B into possition.

Cllutch Ovverload
Thiss machine is ffurnished witth a clutch
overrload protecttion device. It is only to bbe used
to sttop the carriaage power feeed when macchining.
Thee clutch stoop is not designed too stop
carrriage movem ment when th he half nut llever is
enggaged. Attem mpting to use the clutch
overrload system m to stop ccarriage movvement
whiile threadingg, or when th he half nut llever is
enggaged, WILL L cause extennsive damagee to the
he.
lath

Figure 20
0 - Change Gears
G

Stop Blo
ock

Figure 22 – Clutch Torq

que Adjustment

Wheen the feed iss over loaded or the slide ccontacts

the stop block, thhe clutch diseengages the feeed and
stopps the carriagge movementt. An adjustaable nut
Adj. Nutt (Figgure 22) can be rotated inn order to adjjust the
cluttch overload torque. Rotaating the nut inward
Clutch Overlo
oad
incrreases torque,, rotating the nut outward rreduces
torqque. Two adjustment levers (included)
Figure
F 21 – Clutch
C Overlload faciilitate this addjustment. O Of course, thhe stop
blocck can be positioned anyw where along tthe bed
to pprotect the mmachine at anny required position.
Left Threads and Reversee Addditionally, thee stop blockk can be useed as a
macchining stop to make the carriage reppeatedly
Cuttin
ng Feed stopp machining aat a designated position.
When you
u first receive your mach
hine, you willl
find the default
d otated into the
Gear A has been ro
engaged position.
p y need to cut left hand
If you d

21
 SECTION 5: MAINTENANCE
Lubrication
Your lathe has numerous moving metal-to-metal
contacts that require proper lubrication to help
ensure efficient and long-lasting operation.

Other than the lubrication points covered in this

section, all other bearings are internally
lubricated and sealed at the factory. No other
maintenance is required unless they need to be
replaced.

Before servicing, first make sure to clear away

any debris from the oilers in order to avoid
contaminating the lubricant and thereby Figure 24
increasing wear of the moving parts.

DISCONNECT THE LATHE FROM POWER

BEFORE PERFORMING LUBRICATION!

Note: The change gears and the ball oilers

have the same lubrication

Ball Oilers
Lubricant Frequency Qty
ISO 68 or Every 8 1 Squirt
Equivalent Hours From Oil
Lubricant of Operation Can
Figure 25

Figure 23 Figure 26

22
Gearbox Oil Reservoir NOTICE
The feed rate gearbox oil must be changed
Lubricant Frequency Qty after the first three months of operation,
Check/ then annually after that.
ISO 68 or Half-Way
Fill Every 8
Equivalent Mark in To change the oil in the reservoir:
Hours Of
Lubricant Sight Glass
Operation
1. DISCONNECT POWER FROM THE LATHE!
The feed rate gearbox oil reservoir must be
checked and oil added, if necessary, on a daily 2. Remove the reservoir fill plug (see Figure 27).
basis.
Note: If you are experiencing difficulty removing
Tools Needed: the fill plug, do not drain the reservoir until you
Hex Wrench 6mm............................................1 can successfully remove the fill plug. This way
you can still operate the lathe until the issue is
To check and add oil to the reservoir: resolved.

1. Check the oil reservoir sight glass shown in 3. Hold a drain pan under the reservoir drain plug,
Figure 27. If the oil level is below the halfway then remove the drain plug shown in Figure 27,
mark, continue with the following steps to add oil. and allow the oil to completely drain into the pan.

Gibs
There are three gib adjustments for the SC8 -the
cross-slide gib, the compound slide gib, and the
saddle gib.

Cross-slide Gib - The gib on the cross-slide is

adjusted by tightening or loosening the five gib
screws located on the right-hand side of the slide
(shown in Figure 28). Before adjusting the gib
screws, loosen their jam nuts.

Figure 27

2. Wipe clean the area around the fill plug to

prevent debris from falling into the reservoir
when adding oil.

3. Remove the fill plug.

4. Slowly add oil until the oil level is halfway up

the sight glass window.
Figure 28 - Cross slide and compound gib
5. Replace the fill plug. screws

23
The gib is held in place by the setscrews. DO
NOT overtighten. The gib is properly adjusted
when a slight drag is detected while turning the
hand crank. This drag should be evenly
distributed among the 5 setscrews, so adjust each
screw evenly.

Compound Gib—The gib on the compound has

four screws that maintain tension on the slide
(Figure 28). These screws are held in place with
retaining nuts.

To adjust, loosen the retaining nuts and then

tighten the screws evenly to achieve a slight drag
when turning the hand crank. When the proper
tension has been achieved, tighten the retaining
nuts while maintaining the position of the screw
with a hex wrench.

Figure 30 - Carriage gib screws

Before making adjustments to the saddle gibs,

first ensure that the front carriage lock is loose by
turning it counter-clockwise. It is important that
the screws are tightened evenly. A slight drag
should be detected while turning the carriage
hand wheel.

Figure 29 – Carriage gib screws

Carriage Gibs—There are four tensioning

screws for both the front and rear saddle gibs
(Figures 29 & 30).

24
WIRING DIAGRAM - 230V/110V

25
26
27
28
29
30
31
32
33
34
 Note: Description 1 is parts for metric lathe; Description 2 is different parts for imperial lathe.
Part
Code Description 1 Description 2 Qty
No.
101 C82300 Protective shield 1
102 GB/T 70.1 M8 x 12 Screw M8 x 12 2
103 GB/T 97.1 8 Flat washer 2
104 C80107 Bed 1
105 C80111 Lead screw shield 2
106 C80108 Lead screw C80108A 1
107 GB/T 6173 M10 Nut M10 2
108 GB/T 97.1 12 Fat washer 1
109 C80102 Lead screw support 1
110 C80103 Protective support 1
111 GB/T 70.1 M4 x 8 Screw M4 x 8 2
112 C80109 Polish rod 1
113 GB/T 97.1 10 Flat washer 1
114 GB/T 119.1 5 h8 x 30 Round pin 2
115 JB/T7940.4 Φ6 Oil cup 2
116 GB/T 70.1 M8 x 45 Screw M8 x 45 2
117 GB/T 6173 M12 Nut M12 2
118 GB/T 1046 A 4 x 4 x 28 Flat key 2
119 GB/T 70.1 M6 x 12 Screw M6 x 12 8
120 GB/T 119.1 6 h8 x 16 Round pin 4
121 C80110 Rack 2
122 GB/T 97.1 6 Flat washer 4
123 GB/T 70.1 M6 x 12 Screw M6 x 12 2
125 GB/T 6170 M6 Nut M6 2
126 GB 93-87 8 Spring washer 2
127 GB/T 848 10 Flat washer 1
128 GB/T 848 12 Flat washer 1
201 C80214 Spindle box cover 1
202 GB/T 70.1 M5 x 12 Screw M5 x 12 4
203 GB/T 70.1 M5 x 25 Screw M5 x 25 2
204 GB/T 97.1 4 Fat washer 15
205 GB/T 818 M4 x 8 Screw M4 x 8 8
206 C80213 Chuck shield 1
207 C80217 Window 2
208 GB/T 41 M10 Nut M10 3
209 Three jaw chuck Φ130 Three jaw chuck 1
210 C80207 Chuck terminal pad 1
211 GB/T 70.1 M8 x 25 Screw M8 x 25 3
212 C5C0207 Washer 1
213 C80208 Chuck connecting shaft 3
214 C5C0208 Locating sleeve 3
215 GB/T 6170 M6 Nut M6 2
216 C2A0809 Compression spring 1

35
217 C60210 Small shaft 1
218 C60209 Fixed support 1
219 C60208 Shield Limit Board 1
220 C80216 Washer 1
221 C60207 Spindle cover support 1
222 GB 862.1-87 4 Lock washer 3
223 GB/T 97.1 4 Fat washer 15
224 GB 93-87 4 Spring washer 3
225 Gnd φ4 Earth lag φ4 3
226 GB/T 818 M4 x 12 Screw M4 x 12 3
227 C80212 Blackout axis 2
228 GB 894.1-86 - 8 External circlip 2
229 GB/T 70.1 M4 x 30 Screw M4 x 30 4
230 QKS7 Switch 2
231 GB/T 70.1 M4 x 20 Screw M4 x 20 2
232 GB/T 97.1 4 Fat washer 15
233 C80215 Outage mounting plate 1
234 GB/T 97.1 4 Fat washer 15
235 GB/T 6170 M4 Nut M4 2
236 C80201 Spindle box 1
237 GB/T 819.1 M5 x 12 Screw M5 x 12 4
242 ZH-HC-2 change-over switch 1
243 S4-12 Blinding post 2
244 GB/T 70.1 M4 x 30 Screw M4 x 30 4
245 GB/T 70.1 M10 x 35 Screw M10 x 35 4
246 GB/T 819.1 M4 x 12 Screw M4 x 12 14
251 GB/T 97.1 5 Fat washer 2
252 C80211 Spindle locknut 1
253 C80206 Spindle belt wheel 1
254 C80204 Spindle spacer bush 1
255 C80202 Spindle gear 1
256 C80203 Spindle space ring 1
257 6008-2Z GB/T 276-94 Bearing 1
258 GB 893.1-86 - 68 External circlip 1
259 C80210 Oil circle 1
260 32009 GB/T 297-94 Conical roller bearing 1
261 C80209 Oil circle 1
262 GB/T 1096 - A 5 x 5 x 16 Key 1
263 GB/T 1096 - A 5 x 5 x 8 Key 1
264 C80205 Spindle 1
265 GB/T 818 M2.5 x 14 Screw M2.5 x 14 4
266 GB/T 6170 M3 Nut M3 4
267 A-3 Control Panel board 1
268 SC8020105 Plastic ring 4
269 SC8020101 Switch panel 1
270 SC8020103 Compression spring 4
271 GB/T 819.1 M3 x 20 Screw M3 x 20 4

36
272 HY57B Emergency switch 1
273 SC8020102 Control panel stick 1
274 GB/T 70.1 M6 x 16 Screw M6 x 16 3
301 C80310 Hand shank 1
302 Bakelite M8 Baketlite Ball 1
303 C80311 Hand shank 1
304 Bakelite M10 Baketlite Ball 1
305 C8030100 Clamp bolt 1
306 C80309 Locknut 1
307 C5C0316 Clamp washer 1
308 C5C0310 Lock sleeve 1
309 C5C0319 Flat key 1
310 JB/T7940.4 Φ6 Oil cup 1
311 GB/T 97.1 12 Flat washer 1
312 51101 GB/T 301 Thrust ball bearing 1
313 C80308 Tailstock support 1
314 GB/T 70.1 M5 x 16 Screw M5 x 16 4
315 C80306 Tailstock Lead screw 1
316 GB/T 879.1 4 x 20 Round pin 1
317 C5C0617 Hand shank drivepipe 1
318 C5C0608 Hand shank bolt 1
319 C5C0308A Hand wheel 1
320 C5C0412 Spring lamination 1
321 C5C0411 Scale ring 1
Tailstock Lead screw
322 C80307 1
cover
323 C80303 Tailstock platen 1
324 C80301 Stand 1
325 GB/T 70.1 M8 x 35 Screw M8 x 35 2
326 C80312 Nut 1
327 GB 5 M12 x 210 Screw M12 x 210 1
328 GB/T 79 M6 x 16 Screw M6 x 16 1
329 C80302 Tailstock body 1
330 C5C0313 Tailstock center 1
331 C80304 Tailstock Sleeve 1
332 GB/T 879.1 5 x 26 Round pin 1
401 C5C0312 Hand shank 1
402 C80407 Nut 1
403 C80408 Packing washer 1
404 GB 85 M8x30 Screw M 8x30 8
405 C80411 Knife rest 1
406 JB/T7940.4 Φ6 Oil cup 3
407 C80401 Bracket 1
408 GB/T 78 M6 x 10 Screw M6 x 10 1
409 C80405 Feed Nut 1
410 C80403 Knife rest lead screw 1
411 GB/T 879.1 3 x 16 Round pin 1
412 C80406 Bracket 1
37
413 GB/T 70.1 M6 x 16 Screw M6 x 16 2
414 C80410 Scale ring C80410A 1
415 C80414 Hand wheel 1
416 C5C0617 Drivepipe 2
417 C5C0608 Bolt 2
418 GB/T 70.1 M8 x 16 Screw M8 x 16 2
419 C80413 Iron gag 1
420 GB/T 79 M6 x 16 Screw M6 x 16 1
421 C80402 Knife rest turntable 1
421 C80412 Knife rest angle scale 1
422 GB/T 78 M6 x 20 Screw M6 x 20 4
423 GB/T 6172.1 M6 Nut M6 4
Knife rest lead screw
424 C80404 1
cover
425 C80409 Compression bolt 1
426 GB2089 Spring 1
427 GB 75-85 - M4 x 16 Screw M4 x 16 1
428 GB/T 6172.1 M4 Nut M4 1
429 C5C0404 Locating pin 1
430 GB/T 6170 M8 Nut M8 1
501 GB/T 70.1 M8 x 20 Screw M8 x 20 4
Knife rest turntable
502 C80503 1
seat
503 C80505 T nut 4
504 C80502 Work table 1
505 GB/T 879.1 3 x 18 Round pin 1
506 C80520 Gear 22T 1
507 51100 GB/T 301-1995 Thrust ball bearing 2
508 C80516 Lead screw support C80516A 1
509 GB/T 70.1 M6 x 35 Screw M6 x 35 2
510 GB/T 78 M8 x 16 Screw M8 x 16 1
511 C80517 Scale ring 1
512 C5C0412 Spring lamination 1
513 C80518 Hand wheel 1
514 GB/T 6170 M10 Nut M10 1
515 C5C0617 Hand shank drivepipe 1
516 C5C0608 Hand shank bolt 1
517 C80524 Felt 2
518 GB/T 818 M4 x 12 Screw M4 x 12 8
519 JB/T7940.4 Oil cup 4
520 C80514 Preventer plate 1
521 GB/T 848 6 Flat washer 1
522 C80523 Felt 1
523 C80507 Platen 1
524 C80509 Platen 1
525 C80519 Saddle lead screw 1
526 GB/T 70.1 M8 x 45 Screw M8 x 45 1
38
527 GB/T 70.1 M8 x 40 Screw M8 x 40 4
528 GB/T 97.1 8 Flat washer 1
529 GB/T 70.1 M8 x 35 Screw M8 x 35 4
530 C80504 T nut 2
531 C80510 Knife rest dial axis 1
532 C80521 Iron gag 1
533 GB/T 6170 M5 Nut M5 5
534 C80525 Screw 1
535 GB/T 78 M5 x 30 Screw M5 x 30 5
536 GB/T 77 M8 x 8 Screw M8 x 8 2
537 C80515 Preventer plate 2
538 C80501 Saddle 1
539 C80513 Preventer plate 1
540 C80522 Felt 1
541 C80526 Iron gag 1
542 C80508 Platen 2
543 GB/T 97.1 6 Flat washer 4
544 GB/T 70.1 M6 x 20 Screw M6 x 20 5
545 GB/T 75 M4 x 16 Screw M4 x 16 5
546 GB/T 6172 M4 Nut M4 5
547 C80506 Platen 1
548 C80511 Feed screw nut 1
601 GB/T 70.1 M5 x 35 Screw M5 x 35 1
602 GB/T 6172.1 M6 Nut M6 1
603 C80605 Nut C80605A 2
604 GB/T 77 M8 x 10 Screw M8 x 10 4
605 C80606 Platen 2
606 GB/T 96.1 6 Flat washer 1
607 GB/T 6170 M5 Nut M5 2
608 GB/T 70.1 M5 x 16 Screw M5 x 16 2
609 GB 923 M6 Nut M6 1
610 C80616 Nut 1
611 C80615 I axis 1
612 C80626 Support 1
613 GB/T 70.1 M5 x 10 Screw M5 x 10 4
614 GB/T 79 M6 x 12 Screw M6 x 12 1
615 GB/T 77 M6 x 8 Screw M6 x 8 1
616 C80609 Slider 1
617 C80604 Round pin 1
618 GB 894.1-86 - 35 External circlip 1
619 C80603 Control shaft 1
620 C80608 Briquetting 1
621 GB/T 70.1 M6 x 30 Screw M6 x 30 2
622 GB 894.1-86 - 15 External circlip 1
623 C80623 Spacer bush 1
624 C80613 Ⅱ axis 1
39
625 GB/T 119.1 5 h8 x 12 Round pin 1
626 GB/T 119.1 5 h8 x 16 Round pin 2
627 C80602 Camshaft 1
628 C5C0312 Hand shank 1
629 Steel ball Φ6 Steel ball 3
630 C80611 Pressure spring 1
631 C80607 Control shaft 1
632 C80610 Pressure spring 1
633 C80624 Bakelite handle 1
634 GB/T 70.1 M6 x 16 Screw M6 x 16 4
635 C80614 Gear 81T 1
636 GB/T 97.1 6 Flat washer 4
637 C80618 Gear 22T 1
638 C80617 Ⅲ axis 1
639 X3111900 Hand shank 1
640 GB/T 77 M6 x 6 Screw M6 x 6 3
641 GB/T 78 M6 x 6 Screw M6 x 6 3
642 C80620 Ⅳ axis 1
643 C80619 Gear 67T 1
644 C80629 Support 1
645 GB/T 78 M6 x 8 Screw M6 x 8 1
646 C80601 Slide carriage 1
647 GB 894.1-86 - 14 External circlip 2
648 C80621 Gear 60T 1
649 GB/T 1096 - A 5 x 5 x 16 Key 1
650 C5C0617 Hand shank drivepipe 1
651 GB/T 1096 - A 4 x 4 x 16 Key 1
652 C80622 Ⅴ axis 1
653 C80625 Scale ring 1
654 C5C0412 Spring lamination 1
655 C5C0608 Hand shank bolt 1
656 GB/T 77 M6 x 12 Screw M6 x 12 1
657 C80612 Pressure spring 1
701 GB/T 70.1 M5 x 12 Screw M5 x 12 12
702 GB9877.1 22 x 35 x 7 Oil seal 1
703 C80708 End cap 1
704 C8070506 Nameplate 2
705 GB/T 1096 - A 4 x 4 x 16 Key 1
706 C80712 Ⅱ axis 1
707 GB/T 1096 - A 5 x 5 x 80 Key 1
708 C80715 Ⅱ axis spacer bush 1
709 C80725 Gear Z30 C80725A 1
710 C80722 Gear Z28B C80722A 1
711 C80721 Ⅱ axis spacer bush 2
712 C80723 Gear Z25 C80723A 1
714 C80706 Gear Z24 C80706A 1
40
715 C80705 Gear Z28A C80705A 1
716 GB 894.1-86 - 16 External circlip 1
717 C80707 Gearbox casing 1
718 GB/T 1096 - A 5 x 5 x 12 Key 2
719 C80718 Cover 1
720 C80714 Ⅲ axis 1
721 GB/T 1096 - A 4 x 4 x 60 Key 1
722 C80701 Gear Z30 C80701A 1
723 C80717 Ⅲ axis spacer bush 2
724 C80702 Gear Z19 1
725 C8070502 Pin 2
726 C80703 Gear Z40 C80703A 1
727 C80704 Gear Z14 1
728 HE- 30 x 2.65-G-GB/T 3452.1 Seal ring 2
729 C80710 End cap 1
730 GB 894.1-86 - 10 External circlip 1
731 GB9877.1 18 x 30 x 7 Oil seal 1
732 C80103 Support 1
733 GB/T 70.1 M4 x 8 Screw M4 x 8 2
734 C80716 Ⅲ axis connect cover 1
735 Oil screw M16 x 1.5 Oil plug 2
736 AE- 16 x 2.65-G-GB/T 3452.1 Seal ring 3
737 GB2089 0.7 x 4 x 25 Compression spring 4
738 C8070101/02/03 Gear Z13/z40 1
739 HE- 12.5 x 1.8-G-GB/T 3452.1 Seal ring 1
740 C8070104 Axis 1
741 GB/T 78 M5 x 8 Screw M5 x 8 4
742 Oil displaying M16 x 1.5 Oil pointer 1
743 C80709 End cap 1
744 C80719 I axis small bush 1
745 C8070400 Gear C8070400A 1
746 C80713 I axis 1
747 Steel ball Φ5 Steel ball 4
748 C8070300 Gear Z24/16/38 C80724A 1
749 C8070201 Gear Z42 1
750 C80720 I axis big bush 1
751 SOG 25 x 32 x 4 Oil seal 1
752 C80711 End cap 1
753 C8070504 Hand wheel 2
754 C8070202 Hollow cover 1
755 HE- 15 x 1.8-G-GB/T 3452.1 Seal ring 1
756 C8070203 Connecting shaft 1
757 C8070204 Driven shaft 1
758 C8070205 Adjust cover 1
759 C8070206 Compression spring 1
760 C8070207 Screw 1
761 HE- 8.75 x 1.8-G-GB/T 3452.1 Seal ring 1
41
762 GB/T 78 M6 x 12 Screw M6 x 12 6
763 C8070503 Pin 2
764 GB/T 70.1 M8 x 80 Screw M8 x 80 4
765 GB/T 1096 - A 5 x 5 x 50 Key 1
766 GB/T 1096 - A 5 x 5 x 32 Key 1
767 GB/T 879.1 4 x 24 Round pin 1
768 GB/T 819.1 M3 x 6 Screw M3 x 6 4
769 C8070501 Driving lever 2
770 GB/T 879.1 4 x 18 Round pin 6
771 C8070505 Gearbox cover 1
772 GB/T 70.1 M5 x 30 Screw M5 x 30 10
773 C8070507 Nameplate 1
801 GB/T 818 M4 x 10 Screw M4 x 10 12
802 GB/T 97.1 4 Flat washer 24
803 GB/T 6170.1 M4 Nut M4 12
804 3" Hingle 3" Hingle 2
805 C8080400 Cover 1
806 M8 x 1 Sprayer M8 x 1 Sprayer 2
807 C8080107 Axis 2
808 C8080105 Bush 2
809 C8080104 Gear Z36 2
810 C8080106 Washer 2
811 GB/T 70.1 M8 x 25 Screw M8 x 25 2
812 GB/T 97.1 8 Flat washer 2
813 GB/T 78 M5 x 10 Screw M5 x 10 2
814 C8080101 Hanging round body 1
815 C8080300 Round pin 1
816 GB/T 818 M5 x 10 Screw M5 x 10 1
817 C5C1504 Shield 1
818 GB/T 70.1 M6 x 14 Screw M6 x 14 1
819 C8080108 Washer 1
820 GB/T 1096 - A 4 x 4 x 22 Key 1
821 C8080109 Gear Z30 1
822 C8080103 Gear Z48 1
823 C8080110 Spacer bush 1
824 C8080111 Liner pipe 1
825 C8080112 Fixed axis 1
826 GB/T 6170.1 M6 Nut M6 1
827 GB/T 5780 M6 x 35 Hand shank 1
828 C8080211 Transition axis 1
829 GB/T 1096 - A 8 x 7 x 14 Key 1
830 GB 810 M30 x 1.5 Nut M30 x 1.5 1
831 C8080202 Gear Z86 1
832 C8080201 Gear Z91 1
833 C8080205 Shaft sleeve 1
834 C8080204 Washer 1
835 C8080203 Nut 1

42
836 JB/T7940.4 φ6 Oil cup 1
837 C8080505 Compression spring 1
838 GB 896-86 - 6 Ring 1
839 GB/T 6172.1 M12 Nut 12 1
840 C8080503 Locating pin 1
841 GB/T 97.1 12 Flat washer 2
842 C8080501 Nut 1
843 GB/T 879.1 3 x 20 Round pin 1
844 C8080502 Screw M6*15 1
845 GB/T 97.1 6 Flat washer 4
846 C8080102 Hand shank 1
847 C8080206 Washer 1
848 C8080207 Spacer bush 1
849 C8080209 Gear Z90 1
850 GB/T 70.1 M12 x 45 Screw M12 x 45 1
851 GB/T 70.1 M6 x 12 Screw M6 x 12 4
852 C8080210 Hanging round body 1
853 C8080208 Washer 1
901 Power line Power line 1
902 M12 M12 1
903 GB/T 818 M4 x 8 Screw M4 x 8 4
904 C80905 Cover plate 1
905 JCUB2-63 Breaker 1
906 GB/T 819.1 M4 x 8 Screw M4 x 8 2
907 C80906 Spile 1
914 GB/T 70.1 M5 x 12 Screw M5 x 12 4
915 C80214 Spindle box cover 1
916 GB/T 819.1 M3 x 10 Screw M3 x 10 2
917 SS-8B Outlet 1
918 GB/T 6170 M3 Nut M3 2
919 C80902 Angle iron 1
920 GB/T 70.1 M4 x 8 Screw M4 x 8 2
921 GB/T 70.1 M8 x 25 Screw M8 x 25 1
922 GB/T 97.1 8 Fat washer 1
923 C5C1518 Support 1
924 C61511 Washer 1
925 GB/T 70.1 M10 x 40 Screw M10 x 40 3
927 C8090102 Washer 3
938 GB/T 97.1 10 Fat washer 1
939 GB/T 6170 M10 Nut M10 1
941 C80901 Mounting plate 1
942 O-813 Triangle belt 1
944 GB/T 96.1 8 Fat washer 4
951 GB 893.1-86 - 37 External circlip 2
952 C80909 Wheel 1
953 GB 894.1-86 - 12 External circlip 1
954 6301-GB/T 276-94 Bearing 1

43
955 C80911 Shaft 1
956 Z-1500-1 PC Board 1
957 GB/T 819.1 M4 x 12 Screw M4 x 12 4
958 C80904 Cushion board 1
959 GB/T 6170 M8 Nut M8 4
960 GB 93-87 8 Spring washer 8
961 GB/T 70.1 M8 x 25 Screw M8 x 25 4
962 GB/T 70.1 M8 x 40 Screw M8 x 40 4
963 GB/T 5287 6 Flat washer 1
964 C80908 Motor Pulley 1
965 GB/T 1096 - A 6 x 6 x 22 Key 1
966 C80903 Connecting PC Board 1
967 W122-1500C 1500W motor 1
968 C80910 Wheel holder 1

44