Design Aeration1

Wastewater Treatment Plant
Operator Certification Training
Module 17:
The Activated Sludge Process
Part III
Revised October 2014
This course includes content developed by the Pennsylvania Department of Environmental Protection
(Pa. DEP) in cooperation with the following contractors, subcontractors, or grantees:
The Pennsylvania State Association of Township Supervisors (PSATS)
Gannett Fleming, Inc.
Dering Consulting Group
Penn State Harrisburg Environmental Training Center
MODULE 17: THE ACTIVATED SLUDGE PROCESS, PART III
Topical Outline
Unit 1 – Modifications of the Conventional Activated Sludge Process
I. Review of the Conventional Activated Sludge Process

A. Process Description
B. Key Process Design Parameters
C. System Configuration
II. Reasons for Modifying the Conventional Activated Sludge Process

A. Operational Benefits
B. Site Characteristics
C. Economic and Labor Benefits
III. Common Modifications of the Activated Sludge Process

A. Contact Stabilization
B. Kraus Process
C. Step-Feed Aeration
D. Complete Mix
E. Extended Aeration (Oxidation Ditch)
F. Biological Nutrient Removal Processes: Bardenpho, Anaerobic/Anoxic/Oxidation (A2/O),
Modified Ludzack-Ettinger (MLE)
G. Summary: Permissible Aeration Tank Capacities and Loadings
Unit 2 – The Sequencing Batch Reactor (SBR)
I. Description of the SBR Processes

A. Basic Operating Principles of SBR
B. Key Differences Between SBRs and Continuous Activated Sludge
II. Configuration of the SBR System

A. Preliminary Treatment
B. Reactor Components
C. Sequencing Control
D. Ancillary Treatment
Bureau of Safe Drinking Water, Department of Environmental Protection i

Wastewater Treatment Plant Operator Training
MODULE 17: THE ACTIVATED SLUDGE PROCESS, PART III
III. Operation of SBRs

A. Stages of Operation
B. Operating Guidelines
C. Process Control Considerations
Appendix – Sustainable Infrastructure Wastewater Operations Informational Sheet; “Sequential Batch

Reactors (SBR)” Activated Sludge
Bureau of Safe Drinking Water, Department of Environmental Protection ii

Unit 1 – Modifications of the Conventional
Activated Sludge Process
Learning Objectives
• Explain why it may be necessary to modify the conventional activated sludge process.
• List and explain other common modifications of operating the activated sludge process.
Bureau of Safe Drinking Water, Department of Environmental Protection 1-1

REVIEW OF THE CONVENTIONAL ACTIVATED SLUDGE PROCESS
Process Description
The following elements describe the conventional activated sludge process:
• Both influent or primary clarifier effluent and return sludge are introduced at the head of the
aeration tank, which creates the greatest oxygen demand at that point.
• Oxygen demand decreases uniformly from the inlet to the outlet of the aeration tank.
The conventional activated sludge process is susceptible to failure from shock loads.
Shock Load is wastewater with elevated concentrations of contaminants that arrives at the
treatment plant for a brief period of time.
Mixed Liquor Suspended Solids (MLSS), also known as mixed liquor, consists of a mixture of
the influent or primary clarifier effluent and the return sludge, which contains the microorganisms
needed to maintain the treatment process.
Because of its relatively low mixed liquor suspended solids (MLSS) concentration and its head-end
loading, the conventional activated sludge process is most suitable for low-strength, domestic
wastes with minimal peak load considerations.

Key Process Design Parameters

The following range of process design parameters is permissible for a conventional activated sludge
process:
F/M Ratio*.................................................................................................... 0.2 - 0.5 #BOD / #MLVSS / day
Organic Loading (maximum) ....................................................................... 40 #BOD / 1,000 cubic feet / day
MLSS ........................................................................................................... 1000 – 3000 mg / liter
Aeration Retention Time (minimum)** ......................................................... 6 hours
Solids Recycle Rate** .................................................................................. 15% – 100%
*F/M = food to microorganism ratio

#BOD = pounds of Biochemical Oxygen Demand (BOD)
#MLVSS = pounds of Mixed Liquor Volatile Suspended Solids
**Based on maximum monthly average influent flow rate
Biochemical Oxygen Demand (BOD) is the rate at which organisms use the oxygen in water or
wastewater while stabilizing decomposable organic matter under aerobic conditions. In
decomposition, organic matter serves as food for the bacteria and energy results from its
oxidation. BOD measurements are used as a measure of the organic strength of wastes in water.1
Mixed Liquor Volatile Suspended Solids (MLVSS) is the organic or volatile suspended solids in
the mixed liquor of an aeration tank. This volatile portion is used as a measure of the amount of
microorganisms’ present.2

Figure 1.1 Schematic Drawing of a Conventional Activated Sludge System
• The conventional activated sludge process uses a plug-flow reactor that is generally long and
relatively narrow.
• Aeration capacity is uniform along the length of the tank and is designed to minimize back-mixing.
o Commingling of mixed liquor upstream or downstream in any part of the reactor is
minimized.
• Mixed liquor is removed at the end of the aeration tank and transferred to the secondary clarifier.

REASONS FOR MODIFYING THE CONVENTIONAL ACTIVATED SLUDGE PROCESS
Operational Benefits
Modifications to the process can be made in an existing system or in the design process of a new system.
Potential operational benefits of modifying the conventional activated sludge system include:
• Increasing organic loading.
• Providing additional nutrients required for proper treatment.
• Accommodating flow rate or organic loading that varies seasonally.
• Achieving nutrient removal.
Site Characteristics
Another common reason for modification of the process is to provide a treatment system that is suitable to
the available site conditions. For example, extended aeration systems, especially oxidation ditch
configurations, require more space than conventional systems. Alternately, where space is limited, a pure
oxygen system or a complete mix configuration would be more suitable.
These systems, along with others, will be discussed in more detail throughout the chapter.
Economic and Labor Benefits

The energy and labor requirements of each system are determinants in choosing the best modification. A
smaller municipality may not be able to sustain some of the more labor and energy intensive systems. For
example, oxidation ditches are usually low energy, low labor systems. Pure oxygen systems, however,
require greater amounts of energy and labor.

COMMON MODIFICATIONS OF THE ACTIVATED SLUDGE SYSTEM
Contact Stabilization
Process Description
Contact Stabilization presumes that organic matter (BOD) destruction is a two-step process in which:
• BOD is first adsorbed by the microorganisms.
• BOD is then metabolized by the microorganisms for energy and growth.
Adsorption refers to the process in which the colloidal and particulate organic content of the
wastewater becomes attached to the microorganisms.
Based upon that presumption, the contact stabilization process requires two aeration tanks: a contact tank
and a stabilization tank.
A Contact Tank is used for aeration of the mixed liquor.
• Influent or primary clarifier effluent is added to the contact tank.
• While in the contact tank, colloidal and particulate organic matter (BOD) is adsorbed onto the
microorganisms.
• Residence time in the contact tank is approximately 30 to 90 minutes.
• After leaving the contact tank, the mixed liquor is settled in the secondary clarifier and the MLSS
containing the biomass is returned to the stabilization tank.
• The treatment cycle then restarts.
A Stabilization Tank is used to reaerate return sludge prior to mixing it with the primary effluent.
• While in the stabilization tank, most of the organic material that was adsorbed by the
microorganisms in the contact tank is metabolized.
• Residence time in the stabilization tank is approximately 4 to 6 hours.

The following range of process design parameters is permissible for a Contact Stabilization activated
sludge process:
F/M Ratio*.................................................................................................... 0.2 - 0.6 #BOD/#MLVSS/day
Organic Loading (maximum) ....................................................................... 60 #BOD/1,000 cubic feet/day
MLSS ........................................................................................................... 1000 – 3000 mg/liter
Aeration Retention Time (minimum)**ŧ ......................................................... 5 hours

ŧ based on total aeration capacity in contact and stabilization tanks. (The stabilization tank is typically 30-
35% of the capacity of the contact tank)
System Configuration
To modify the conventional activated sludge system into a contact stabilization system, the following
changes are made:
• Primary effluent is introduced into the Contact Zone.
• A stabilization tank is added to stabilize the adsorbed organics.
• Overall oxygen demand is split between contact tank and stabilization tank.
• A benefit of this process modification is the ability to perform well under high flow, wet weather
conditions.

Figure 1.2 Schematic Drawing of a Contact Stabilization System3

Kraus Process
Process Description
Kraus Process is used to treat wastewater that is deficient in nitrogen. It is also used when activated
sludge has poor settling characteristics. This modification is most applicable for treatment facilities
receiving wastewater that is high in carbohydrates.
The process uses a reaeration tank that is similar to the contact stabilization process, with some important
modifications:
• Not all of the return sludge is reaerated; some is returned without being retreated.
• Digester supernatant and digester sludge is also added to the reaeration tank.
• Retention time in the reaeration tank is approximately 24 hours.
Ammonia nitrogen in the digester sludge and supernatant is converted to nitrate nitrogen in the reaeration
tank. Effluent from the reaeration tank is mixed with the return sludge to correct the nitrogen deficiency in
the influent wastewater. Also, the concentration of inert solids from the digester, when mixed with the
mixed liquor, improves the settleability of the mixed liquor.
The following range of process design parameters is permissible for a Kraus activated sludge process.ŧ
MLSS ........................................................................................................... 1000 – 2500 mg/liter
Aeration Retention Time (minimum) ............................................................ 4 hours
ŧ Does not consider the reaeration tank


To modify the conventional activated sludge system into a Kraus process system, the following changes
are made:
• The reaeration tank is added.
• Recycling and reaeration of the digester supernatant and solids occurs.
• A portion of the return sludge is reaerated.
Figure 1.3 Schematic Drawing of a Kraus System

Step-Feed Aeration
Process Description
This process modification is used to provide a more uniform distribution of oxygen demand throughout the
aeration tank. It is particularly beneficial when dealing with variable shock loads.
• Primary effluent is piped to two or more locations along the length of the aeration tank.
• Distributed loading minimizes any decreases in dissolved oxygen concentration along the length of
the aeration tank.
• The percent of primary effluent distributed to each location can be varied to optimize process
performance.
The following range of process design parameters is permissible for a step feed activated sludge process:
MLSS ........................................................................................................... 1000 – 3000 mg/liter

To modify the conventional activated sludge system into a step-feed aeration system, the following
changes are made:
• Primary effluent is distributed to multiple locations in the aeration tank.
• Baffling of the aeration tank creates multiple mixing zones coincident with the distribution points.
• Operational flexibility is achieved by varying the amount of primary effluent distributed to each area.

Figure 1.4 Schematic Drawings of Various Step-Feed Aeration Modes5

oxygen supply
Oxygen/
Levels
BOD
oxygen demand (BOD)
Tank Length
Oxygen Supply versus Oxygen Demand for Step Aeration
Complete Mix
Process Description
This modification is used to simulate a completely-mixed reactor tank in which conditions within the tank
are the same throughout the tank. The benefits of this modification include greater volumetric loading, a
more stable microbial population, more efficient aeration, and tolerance of shock loads.
• Both primary effluent and return sludge are distributed uniformly along the length of the aeration tank.
• Mixed liquor is removed uniformly from the length of the aeration tank.
• Aerators are located uniformly along the aeration tank.
The following range of process design parameters is permissible for a complete mix activated sludge
process:
MLSS ........................................................................................................... 1000 – 3000 mg/liter


To modify the conventional activated sludge system into a complete mix system, the following changes are
made:
• Primary effluent is distributed to multiple locations throughout the aeration tank.
• The flexibility of operation is enhanced by varying the amount of primary effluent distributed to each
location.
• Baffling of the aeration tank creates multiple mixing zones coincident with the distribution points.
Figure 1.5 Schematic Drawings of a Completely-Mixed Aeration System5

Schematic Drawing of a Completely-Mixed Aeration System

Oxygen/
Levels
BOD
oxygen supply
oxygen demand (BOD)
Tank Length (and Width)
Oxygen Supply vs. Oxygen Demand for Complete Mix Aeration

Extended Aeration (Oxidation Ditch)

Process Description
Extended aeration is often used for small treatment facilities requiring a simple process, in the form of a
package treatment plant. It is also used for larger treatment plants in the form of oxidation ditches.
Principal benefits of extended aeration modifications include reduced sludge handling and lower power
requirements.
(NOTE: an overview of package plants and oxidation ditches is available in Module 4 of the DEP
Wastewater Treatment Plant Operator Training.)
• A long aeration time (hydraulic loading) and low organic loading characterize this process.
• Primary clarification is often eliminated.
• Dissolved oxygen (DO) is introduced at intermittently spaced aerators and the DO concentration
may be allowed to decrease significantly between aerators.
• The ditch configuration and the mixing energy applied are designed to maintain a velocity of
approximately one foot per second, in order to keep solids in suspension.
The following range of process design parameters is permissible for an extended aeration and oxidation
ditch activated sludge processes:
MLSS ........................................................................................................... 3000 – 5000 mg/liter


In this example of extended aeration, an oxidation ditch configuration is presented as a representative of

the extended aeration modification. Many other configurations are possible. The principal differences
between an oxidation ditch and a conventional activated sludge system are:
• An oxidation ditch is configured as a ring with continuous flow around the ring, which is induced by
aerators.
• A clarifier may be located within the annular space of the ditch to save on construction costs and
the amount of land required.
• Oxidation ditch rings may be interconnected at the ends in order to produce a long, continuous
loop.
Figure 1.6 Schematic Drawing of an Oxidation Ditch

Oxygen/
oxygen supply
Levels
BOD
oxygen demand (BOD)
Oxidation Ditch Loop Cycle
Oxygen Supply versus Oxygen Demand for Oxidation Ditch

Biological Nutrient Removal Processes:

Bardenpho, Anaerobic/Anoxic/Oxidation (A2/O), Modified Ludzack-Ettinger (MLE)
Process Description
These process modifications to the conventional activated sludge system are made to enhance the removal
of nutrients from wastewater. A simple Bardenpho process is presented here to represent the range of
Biological Nutrient Removal Processes.
(NOTE: An overview of Biological Nutrient Removal processes is available in Module 8, Overview of

Advanced Wastewater Treatment, of the DEP Wastewater Treatment Plant Operator Training.)
• Ammonia nitrogen, which is present in raw municipal wastewater, is converted to nitrate nitrogen
during normal activated sludge treatment.
• Anoxic (containing no residual dissolved oxygen) tanks or zones are added to the conventional
activated sludge process train to convert the nitrates to nitrogen gas.
• In the anoxic zones, facultative bacteria strip oxygen from the nitrates since oxygen is not available
in dissolved form in the wastewater.
Key Process Design Parameters (Typical Design)
The successful operation of a biological nutrient removal (BNR) system is dependent upon several process
parameters, including:
• Temperature, which affects microbial reaction rates.
• pH and alkalinity, which must be controlled to prevent inhibition of microbial reactions.
• Dissolved oxygen concentration, which affects reaction rates and creates inhibitions.
• Mixing, this ensures uniform reactor conditions.
• Return of activated sludge and internal nitrate recycling, which provides necessary microorganisms
and nitrate for the denitrification process in the anoxic zones.

The following range of process design parameters is permissible for the aeration tank in a Bardenpho
activated sludge process:
MLSS ........................................................................................................... 2000 – 5000 mg/liter
Clarifier Solids Recycle Rate**..................................................................... 15% – 100%
Aeration Tank MLSS Recycle Rate**….………………………………………..400%

A simple four-tank Bardenpho process may be configured as follows:
• Influent wastewater, return sludge from the clarifier, and nitrified mixed liquor from the effluent end
of the first aeration zone are introduced into the first anoxic tank.
• Effluent from the first anoxic tank discharges to an aerobic tank where nitrification occurs.
• Effluent from the nitrifying tank discharges to a second anoxic tank where denitrification occurs.
o Nitrate-nitrogen is converted to nitrogen gas.
• Effluent from the denitrification tank discharges to a second aerobic tank.

o Second tank raises DO level of the wastewater before clarification process begins.
• To obtain phosphorus removal, as well as nitrogen removal, an anaerobic tank is typically added to
the front of the treatment train.
Several other configurations have been used to achieve biological nutrient removal.
• The MLE (Modified Ludzak Ettinger) process uses only the first two tanks in the four-stage
Bardenpho process: the anoxic tank followed by the aeration tank. Both clarifier solids and
aeration tank MLSS are returned to the anoxic tank.
• The A2/O (anaerobic, anoxic and aerobic, or oxic) process adds an anaerobic tank to the head of
the MLE process and returns clarifier solids to this tank rather than the anoxic tank. The A2/O
process will provide phosphorus as well as nitrogen removal.

ANOXIC AEROBIC ANOXIC AEROBIC
Figure 1.7 Schematic Drawing of the Representative Bardenpho System9

Permissible Aeration Tank Capacities and Loadings7
Process Mode of Aeration Minimum Aeration Maximum Aeration Tank F/M Ratio MLSS
lb. BOD/lb.
Retention Time—Hours Organic Loading***** MLVSS/day
mg/liter
(based on maximum monthly Lb. BOD/1000 cu. ft./day
average flow)
Step Aeration, Air System 6 40 0.2 – 0.5 1000 – 3000

Complete Mix, and
Conventional Pure Oxygen System 2 160 0.3 – 1.0 3000 – 5000
Activated Sludge
Contact Stabilization Air System 5* 60 0.2 – 0.6 1000 – 3000
Combined Carbon Air System 12 20 .08 - .16 2000 -5000

Oxidation-Nitrification
Pure Oxygen System 4 60 .10 - .20 3000 – 5000
Extended Aeration Air System 24 15 .05 – 0.1 3000 – 5000

and
Oxidation Ditches
Carbonaceous Stage Air System 4 70 0.3 – 0.8 1000 – 2500

of Separate Stage
Nitrification Pure Oxygen System 1.5 250 0.5 – 1.0 3000 – 5000
Nitrification Stage of Air System 6 10*** .05 - .20**** 1000 – 3000

Separate Stage
Nitrification Pure Oxygen System 2 25*** .08 - .20**** 3000 - 5000
* Total aeration capacity includes both aeration and reaeration capacities. Normally the contact zone equals 30-35% of the total aeration capacity.
** Not recommended if wastewater temperatures are expected to fall below 10º C.
*** Lb. NH3-N/1000 cu. ft./day
**** Lb. NH3-N/lb. MLVSS/day
***** Based on maximum daily BOD load to aeration tank.

KEY POINTS
Key Points for Unit 1 - Modifications of the Conventional Activated Sludge Process
• Because of its relatively low mixed liquor suspended solids (MLSS) concentration and
its head-end loading, the conventional activated sludge process is most suitable for
low-strength, domestic wastes with minimal peak load considerations.
• Typical key process design parameters for an activated sludge process include: F/M
ratio, organic loading (max), MLSS, aeration retention time (minimum) and solids
recycle rate.
• Oxidation ditch systems require more space than conventional systems but are usually
low energy and low labor systems.
• The conventional activated sludge process uses a plug-flow reactor that is generally
long and relatively narrow.
• Oxidation ditch systems require more space than conventional systems but are usually
low energy and low labor systems.
• The contact stabilization process requires two aeration tanks, a contact tank and a
stabilization tank.
• The Kraus Process is often used to treat wastewater that is nitrogen deficient or has
poor settling characteristics.
• A step-feed aeration system is beneficial when dealing with variable shock loads.
• A complete mix process can result in greater volumetric/hydraulic loading capacity.
• Influent with low organic loading may be a good candidate for extended aeration in
package treatment plant or oxidation ditch treatment processes.

EXERCISE
Exercise for Unit 1 - Modifications of the Conventional Activated Sludge Process
1. BOD measurements are used as a measure of the _____________________ strength

of wastes in water.
2. The conventional activated sludge process uses a _________ - __________ reactor

that is generally long and relatively narrow.
3. Potential benefits of modifying the conventional activated sludge system include:
a. Increasing organic loading.
b. Providing additional nutrients required for proper treatment.
c. Accommodating flow rate or organic loading that varies seasonally.
d. Achieving nutrient removal.
e. All of the above
4. The contact stabilization process assumes that organic matter is first

_______________ by the microorganisms and then organic matter is
_________________ by the microorganisms for energy and growth.
5. In a contact stabilization activated sludge process, the maximum organic loading

should be no more than ________________ per 1,000 cubic feet/day.
6. The Kraus Process is applicable to treatment facilities receiving waste water that is low
in carbohydrates.
a. True b. False
7. The _______-__________ Aeration Process can be used to provide a more uniform

distribution of oxygen demand throughout the aeration tank.
8. In general, the __________________________ process requires the longest minimum

aeration time.
9. Oxidation ditches are configured in a ring with ______________ flow around the ring
that is induced by aerators.
10. Because of its relatively low mixed liquor suspended solids (MLSS) concentration and
its head-end loading, the ____________ activated sludge process is most suitable for
low-strength, domestic wastes with minimal peak load considerations.

EXERCISE
Exercise – Unit 1: Place the letter of the description before the appropriate treatment process.
A. The principal benefits of this modification

include reduced sludge handling and lower
_____Conventional
power requirements. Of the processes listed,
_____Complete-Mix this type of plant will perform the best in regards
______Contact Stabilization to achieving nitrification because of the long
aeration and MCRT.
_____Extended aeration/
oxidation ditch B. The benefits of this modification include
_____Step-feed greater hydraulic loading, a more stable microbial
population, more efficient aeration, and tolerance
_____Kraus of shock loads. These systems may be used for
nitrification, however; they can be more sensitive
to pH drops.
C. This process is most suitable for low-strength,

domestic wastes with minimal peak loads. The
system works well for nitrification. However, the
process is susceptible to failure from shock
loads.
D. This process is often used to treat wastewater

that is nitrogen deficient, high in carbohydrates
and has poor settling characteristics.
E. This process presumes that organic matter

(BOD) destruction is a two-step process in which
BOD is first adsorbed by the microorganisms
then metabolized by the microorganisms for
energy and growth. Hydraulic detention times
are too short for significant nitrification to occur
making the process unsuitable for nitrification.
This modification performs well under high flow,
wet weather conditions.
F. This process modification is used to provide a

more uniform distribution of oxygen demand
throughout the aeration tank. It is particularly
beneficial when dealing with variable shock
loads. It can be used to provide partial
nitrification, however; detention times are too low
for complete nitrification to occur.

REFERENCES
California State University, Sacramento, Department of Civil Engineering, Operation of

1
Wastewater Treatment Plants Volume I , 4th ed., (Sacramento, CA: The California State University,
Sacramento Foundation, 1994).
2 Operation of Wastewater Treatment Plants Volume 1, 4th ed.
3 Operation of Wastewater Treatment Plants Volume II, 5th ed., page 86, figure 11.23.
4 Operation of Wastewater Treatment Plants Volume II, 5th ed., p. 89, figure 11.25.
5 Operation of Wastewater Treatment Plants Volume II, 5th ed., p. 91, figure 11.26.
6 Operation of Wastewater Treatment Plants Volume II, 5th ed., p. 92, fig. 11.28.
7 http://www.elibrary.dep.state.pa.us/dsweb/Get/Document-48793/362-0300-001.pdf, p.78.

Unit 2 – The Sequencing Batch Reactor
Learning Objectives
• Explain the basic operating principles of Sequencing Batch Reactors.
• State the differences between a Sequencing Batch Reactor and Continuous Activated Sludge
Process.
• Explain the configuration of a Sequencing Batch Reactor System, including preliminary treatment,
reactor components, sequencing control, and ancillary treatment.
• Describe the stages of operation for a Sequencing Batch Reactor.
• Discuss the reasons for wasting sludge from a Sequencing Batch Reactor.
• Identify key guidelines for operating a Sequencing Batch Reactor.
• Describe important process control considerations for a Sequencing Batch Reactor.

DESCRIPTION OF THE SEQUENCING BATCH REACTOR (SBR) PROCESS
Basic Operating Principles of the Sequencing Batch Reactor (SBR)

Following are the basic overview principles of the SBR:
• The SBR is a fill-and-draw activated sludge system.
• Wastewater enters a partially filled reactor containing biomass.
• When the required operating liquid level is reached, influent flow to the reactor stops and a
specified, timed treatment sequence begins.
• Because the influent flow to each reactor is not continuous, at least two reactors are necessary to
accommodate a system with continuous influent flow.
Parameters of the SBR
• Multiple processing stages occur in one tank.

o SBRs use specified time durations for each treatment process.
o A typical operating schedule includes fill, react, settle, decant, and idle stages.
o Stage timing is usually controlled automatically.
• Multiple processing cycles occur each day.

o Typically, from two to six complete treatment cycles will be completed in each reactor each
day.
• Batch processing of wastewater occurs.

o A normal SBR system operates in the batch mode, wherein the influent flow is cyclic and
each batch is processed through the entire treatment process.
• SBR modifications provide continuous processing of wastewater.

o A modification of the normal SBR process allows for continuous influent flow without
sacrificing the benefits of the SBR process.
 The Intermittent Cycle Extended Aeration System (ICEAS) operates with a
continuous influent flow and a periodic discharge.
 ICEAS uses an inlet baffle to separate the inlet zone from the reactor zone,
allowing semi-batch treatment with minimal disruption of clarification.

Key Differences Between SBRs and Continuous Activated Sludge

The unit processes of SBRs and conventional activated sludge systems are the same. However, these
processes occur over time in the SBR; in the conventional system, the unit processes occur
simultaneously.
Inflow/Outflow Characteristics
• Both influent and effluent flows occur periodically in an SBR, which is a batch activated sludge
process; therefore, the continuous treatment plant influent periodically transitions from one reactor
to another.
How do influent and effluent flows occur in the conventional activated sludge process?
______________________________________________________________________________
______________________________________________________________________________
Aeration Schedule
• Aeration is just one of several treatment stages in the SBR.
When does aeration occur in the conventional activated sludge process?

______________________________________________________________________________
______________________________________________________________________________
Organic Loading Schedule
• Organic loading occurs intermittently, within the influent flow, in the SBR.
When does organic loading occur in the conventional activated sludge process?
______________________________________________________________________________
______________________________________________________________________________
Mixed Liquor Management
• Mixed liquor always remains in the reactor in SBR systems; no sludge return is required.
What happens to the return sludge in the conventional activated sludge process?
______________________________________________________________________________
______________________________________________________________________________

Clarification Efficiency
• Clarification occurs in an ideal environment in the SBR because there is no flow through the
reactor during the clarification stage.
What makes clarification efficiency less than ideal in the conventional activated sludge process?
______________________________________________________________________________
______________________________________________________________________________
Complexity of Operation
• There is not a significant difference in the overall complexity of operation between SBRs and
conventional activated sludge processes.
• Each SBR reactor is required to perform several functions, making operation of the reactor more
complex than any one component of a conventional activated sludge system.
• Because the conventional activated sludge system uses several individual components, operation
of the conventional system may be considered to be more complex than operation of any one SBR
reactor.
• SBR systems require a minimum of two reactors to handle continuous flow; however, each reactor
has less mechanical equipment than a conventional activated sludge system (including the clarifier
and return activated sludge components).

CONFIGURATION OF A SEQUENCING BATCH REACTOR (SBR) SYSTEM
Preliminary Treatment
• Most treatment plants have some preliminary treatment to protect treatment equipment and
preserve the effectiveness of the treatment process.
• As is typical of most extended aeration systems, primary clarification is not commonly used for
SBRs
.
Figure 2.1 SBR Treatment Train with Preliminary Treatment1

Reactor Components
Tanks
• Multiple tanks are required; the minimum is two.

o One reactor fills and reacts while the other settles and decants.
• For best practice, use a minimum of three reactors to ensure that continuous operation is possible
at all times.
• Tank configurations vary with manufacturers, but the most common configuration is rectangular.
• SBR reactors are usually deeper than conventional activated sludge aeration tanks.
• The maximum operating depth for typical SBR reactors ranges from 12 to 20 feet.

Decanters
• Decanter designs and configurations vary with the manufacturer.
• Decanters can be fixed-elevation or variable-elevation (floating) devices.
• Floating decanters are more expensive, but offer more flexibility in operation.
Figure 2.3 Decanters

Aeration and Mixing Equipment
• The same aeration and mixing equipment that is used for conventional activated sludge systems is
used in the SBR systems.
• Mechanical mixers are commonly used in SBRs.

o A submerged turbine aerator that uses mechanical mixing and optional aeration is often
used for SBR systems.
• The use of air diffusers without mechanical mixers limits the flexibility of the SBR system.
o Air diffusers alone are not used in SBR systems designed for nutrient removal because
anoxic or anaerobic treatment cycles are required for nutrient removal.
• Jet aerators are used more often in SBR systems than in conventional activated sludge systems
because of their ability to mix without aerating.
o Jet aerators can be used with only a liquid motive force (for pumping mixed liquor), or with
a combination of liquid and air streams to aerate.
Activated Sludge Wasting Components
• Sludge wasting is performed on an as-needed basis to manage the food to microorganism ratio in
the SBR.
• Sludge wasting occurs intermittently, following the decant stage or during the idle stage of
operation.
• Sludge is removed by gravity line or by pumps.

Sequencing Control
The PLC
• A Programmable Logic Controller (PLC) controls the sequencing of the reactor cycles.
• A battery backup should be installed to provide power to the PLC in case of power failure.
• Good practice requires that the PLC also be protected by an Uninterruptible Power Supply (UPS)
to prevent PLC memory loss and to maintain normal operations during short power outages.
Figure 2.4 Programmable Logic Controller4

Automatically Actuated Valves
• Operations regulated or controlled by pneumatic, solenoid, or motorized valves can all be

controlled from a centralized location with a PLC.
Instrumentation
• Motor starters, valves, level controls, timers, flow meters, and pressure switches are all controlled
by the PLC.
• Display panels may be used to provide an operational overview and the status of individual
instrumentation devices.
Software
• The PLC software is usually supplied by the PLC manufacturer.
• The software is unique for each individual SBR system manufacturer; it is one of the main features
that differentiate between SBR systems.

Ancillary Treatment
Post treatment can be used to disinfect the effluent or to process waste activated sludge.
Disinfection of Effluent
• Effective disinfection requires adequate contact time between the effluent and the disinfection
chemical.
• Disinfection of SBR effluent requires special consideration because the effluent flow rate from an
SBR is typically much greater than the average influent flow rate to the treatment facility, since the
effluent is discharged as a batch, not continuously.
• If equalization of SBR effluent is not provided, the disinfection facilities must be sized to handle the
SBR effluent flow rate, while still providing the requisite time for effective disinfection.
Processing of Waste Activated Sludge
• Waste activated sludge may be discharged directly to sludge drying beds.
• Alternately, some SBR facilities are supported by aerobic sludge digesters that process waste
activated sludge from the SBRs.
Figure 2.5 Processing of Waste Activated Sludge5

OPERATION OF SEQUENCING BATCH REACTORS (SBRS)
Stages of Operation
2.6 Stages of the SBR6

The following details what you may expect in each of the operational modes.
Fill
• During the fill stage, effluent from the primary treatment systems discharges to one or more of the
SBR reactors.
• During this stage, the fluid level in the reactor is increased from the low water level (achieved after
decanting) to the high water level.
• The fill cycle can be operated in a variety of ways, depending upon the treatment objective(s).
o Fill can occur without any mixing or aeration; with mixing only; or with mixing and aeration.
React
• After the SBR is filled to the high fluid level, the react cycle typically begins.
• When the SBR is operating in the extended aeration mode, the react cycle is operated with full
aeration and mixing to achieve the desired treatment.
o Alternately, depending on the treatment objectives, the react stage may be operated with
mixing but without aeration.
Settle
• Generally, settling occurs under quiescent conditions with no mixing or aeration.

o Quiescent settling facilitates the formation of a sludge blanket, which produces a clear
supernatant above the sludge blanket.
• In some situations, gentle mixing during the initial settling stage may encourage floc formation and
produce a better quality effluent.
• Control of the settling stage duration is usually based on a timed cycle. .
Decant
• During the decant stage, supernatant liquid is withdrawn from the top of the liquid surface in the
reactor and is discharged as plant effluent.
o Because there is no influent flow during the decant stage, the liquid level in the tank
decreases as supernatant is withdrawn from the reactor.
• Baffles or weirs are typically used to prevent scum and other floating solids from entering the
effluent discharge.

Idle
• Idle stage is not a required SBR operating stage.
• An idle stage, if needed, is used to allow the multiple SBR reactors to synchronize so that one SBR
reactor can complete its fill stage before the plant influent is allowed to discharge to the idling
reactor.
• The idle stage can be used for removal of waste sludge.

Operating Guidelines
Operating guidelines vary significantly, depending upon the treatment objective(s). Operating guidelines for
industrial wastewaters will differ from guidelines for municipal wastewater. The following information is a
generalized overview of operating guidelines.
F/M Ratio
• For municipal wastewater, with operation of the SBR as a typical aeration plant, the F/M ratio is
0.05 to 0.10.
• For municipal wastewater, if the objective is not to nitrify, an appropriate F/M ratio would be 0.15 to
0.4.
MLSS Concentration
• The MLSS concentration maintained in the SBR ranges from 2000 to 5000 milligrams per liter
(mg/L), when there is a low liquid level in the SBR.
• Consistency is required in calculating the MLSS concentrations because the liquid level in the SBR
reactor varies with time. Therefore the MLSS concentration must be sampled during the same
phase every time.
Sludge Age
• SBRs are operated as extended aeration facilities and have a sludge age typical of those systems:
from 25 to 45 days.
Reaction Stage Dissolved Oxygen (DO) Concentration
• During full aeration of the SBR reactor during the react stage, the DO concentration should not be
limiting and should range from at least 1.0 mg/L to approximately 3.0 mg/L.
• Other modes of operation are possible; this could dictate DO concentrations during the react stage
that would be different from that suggested above.

Process Control Considerations

Modifying the Stages of a Cycle to Affect Performance
• It is relatively easy to modify the stages of an SBR cycle by adjusting the timing for each treatment
stage with the PLC.
o New treatment cycles can be added, and the characteristics of each treatment cycle can
be altered.
o These changes require an operator who is knowledgeable about the PLC.
• Radical changes in the SBR cycles require prior knowledge of the required process parameters
and/or close process monitoring to ensure the success of process changes.
Figure 2.7 Typical Operational Strategies7
Why is the settling time longer when removing phosphorus (P)?

________________________________________________________________________
________________________________________________________________________

Monitoring Consistency
• Monitoring requirements for SBRs are very similar to those of other activated sludge systems.
• F/M ratio and dissolved oxygen concentrations are basic parameters that should be monitored for
all activated sludge systems, including SBRs.
o Since SBRs are somewhat unique, in that several processes occur in a single tank.
 Monitoring activities must account for this uniqueness.
 Effective monitoring will be done consistently at the same time in the cycle.
 Measurement of the MLSS, in particular, is critical to process monitoring and must
always be conducted at the same point in the process cycle.
Knowing Your PLC
• The PLC is the heart of the SBR operation because it controls the operation of the mechanical
equipment and the timing of the treatment stages.
• Operators need to be familiar with the operation of the PLC in order to properly operate and control
the SBR process.
• Operator knowledge should extend to being able to troubleshoot the PLC and to knowing how to
return the PLC back into service if a power failure occurs and the uninterruptible power supply
(UPS) is not online.

KEY POINTS
Key Points for Unit 2 – The Sequencing Batch Reactor (SBR)
• Typically, at least two Sequencing Batch Reactors (SBRs) are needed to accommodate a
system with continuous influent flow.
• A SBR system can typically finish from two to six complete processing cycles per day.
• A typical SBR cycle contains the following stages: fill, react, settle, decant and idle.
• SBR systems are usually deeper than conventional activated sludge aeration tanks.
• Sludge wasting occurs intermittently on an as needed basis in the SBR.
• A Programmable Logic Controller (PLC) controls the operation of the mechanical equipment
and the timing of the treatment stages in a SBR process.

EXERCISE
Exercise for Unit 2 – The Sequencing Batch Reactor
1. The maximum operating depth of a typical SBR system ranges from _________ to ___________
feet.
2. SBR systems can in general use the same aeration and mixing equipment that is used for
conventional activated sludge systems.
a. True b. False
3. PLC means _________________ __________________ ________________. A PLC controls

the mechanical equipment and the timing of the different stages.
4. List the five stages of operation in a SBR and briefly explain what happens in each stage.
a.
___________________________________________________________________________
___________________________________________________________________________
_________________________________________________________
b.
___________________________________________________________________________
___________________________________________________________________________
_________________________________________________________
c.
___________________________________________________________________________
___________________________________________________________________________
_________________________________________________________
d.
___________________________________________________________________________
___________________________________________________________________________
_________________________________________________________
e.
___________________________________________________________________________
___________________________________________________________________________
_________________________________________________________

UNIT 2 REFERENCES
California State University, Sacramento, Department of Civil Engineering, Operation of

1
Wastewater Treatment Plants, Volume II, 5th ed., (Sacramento, CA: The California State University,
Sacramento Foundation), page 95, figure 11.29.
3 Operation of Wastewater Treatment Plants page 98, figure 11.31.
4 Operation of Wastewater Treatment Plants, p. 101, figure 11.34.

APPENDIX
Bureau of Water Standards and Facility Regulation

Division of Technical and Financial Assistance
May 2014
Sustainable Infrastructure
Wastewater Operations Informational Sheet
“Sequential Batch Reactors (SBR)”

Activated Sludge
Important Notice: The information contained in this document is for informational
purposes only and IS NOT an all-inclusive source of information in regard to SBR
systems. This sheet is intended to assist operators with a basic understanding of SBR
systems Please consult with your system manufacturer and engineer for specific details
and information in regard to your SBR system. All facility owners and operators should
become familiar with your facility NPDES Permit and the requirements for compliance
contained within the permit. Nothing contained herein should be considered an
endorsement or condemnation by PA DEP of any person, product, location or technique.
For more information please contact:

Thomas J. Brown – Water Program Specialist
Pennsylvania DEP – Cambria Office
286 Industrial Park Road
Ebensburg, PA 15931
Tele: (814) 472-1900
thbrown@state.pa.us
APPENDIX
Glossary of Terms and Acronyms
• BNR – Biological Nutrient Removal (typically nitrogen and phosphorus in

wastewater).
• BOD – Biochemical Oxygen Demand
• DMR – Discharge Monitoring Report, to be submitted to regulatory
authorities typically on a monthly basis as required by the facility NPDES
Permit.
• ENR - Enhanced Nutrient Removal provides a greater degree of treatment
when compared to BNR.
• F/M – Food to Microorganism ratio.
• MCRT – Mean Cell Residence Time
• MLSS – Mixed Liquor Suspended Solids
• MLVSS – Mixed Liquor Volatile Suspended Solids
• NH3-N – Formula for ammonia nitrogen in wastewater
• NO2 – Formula for Nitrite in wastewater
• NO3 – Formula for Nitrate in wastewater
• NPDES – National Pollutant Discharge Elimination System, all facilities that
discharge must have an NPDES permit. This permit dictates the terms,
conditions and parameters for operating your treatment plant. This permit is
backed by state and federal law.
• PA DEP – Pennsylvania Department of Environmental Protection, the state
regulatory agency.
• POTW – Publicly Owned Treatment Works
• SBR – Sequential Batch Reactor, a type of activated sludge process that
treats wastewater in batches.
• Sludge Age – The theoretical age of the solids under aeration in the system,
basically the same calculation as MCRT.
• SVI – Sludge Volume Index is a calculation that indicates the tendency of
activated sludge solids (aerated solids) to thicken or to become concentrated
during the sedimentation/thickening process.
• SWD – Side Water Depth, the depth of water in a tank at any given time.
• TN – Total Nitrogen
• US EPA – United States Environmental Protection Agency, the federal
regulatory agency.
• WAS – Waste Activated Sludge refers to the amount of sludge (or biosolids)
removed or wasted from the system.
Bureau of Safe Drinking Water, Department of Environmental Protection

APPENDIX
Activated Sludge - Sequential Batch Reactor (SBR)

Operational Information Sheet
Introduction:
The sequential batch reactor is a form of activated sludge and is subject to all of the operating
parameters that would be applied to any other activated sludge system (such as F/M, SVI, MLSS,
alkalinity, etc…). A solid understanding of the activated process is necessary in order to
properly operate an SBR system. The batch reactor differs from a conventional flow through
system in that everything happens with in a given tank in different modes. There is no separate
aeration tank and clarifier as you would find in a flow through system. There are at least two
batch reactor tanks and in some cases many more. The batch reactor relies on a computer or
programmable logic controller (PLC) to sequence and control the batches.
As with any activated sludge system, maintaining a proper mass balance is crucial for proper
treatment. Simply put, the mass balance refers to the amount of living biomass (activated sludge)
we must maintain in order to obtain proper treatment. Too much or too little biomass will result
in inadequate or poor treatment. The typical measurement for the determination of required
biomass (activated sludge) is known as the “Food to Microorganisms Ratio (F/M). For all
wastewater treatment systems, effluent parameters will dictate the degree of treatment necessary
and the amount of biomass (activated sludge) that must be maintained. Facilities with permit
requirements for nitrification, denitrification and phosphorus removal will require much closer
operator scrutiny and action in order to maintain proper treatment. Facilities that are required to
achieve nitrification will typically run a much higher “Mean Cell residence Time (MCRT) or
“Sludge Age” as compared to a facility that has no such requirement.
SBR’s (as well as any other biological treatment process) will produce excess sludge or biosolids
that must be removed and disposed of. Proper handling of sludge is essential through a regular
routine of wasting in order to maintain a proper mass balance. A detailed estimation of sludge
production can be found in the US EPA handbook titled “Improving POTW Performance Using
the Composite Correction Approach”. As a general rule of thumb, you can figure that you will
produce ½ lb of new sludge per pound of BOD removed. Facilities that add a metal salt (such as
aluminum sulfate) for phosphorus removal can expect higher sludge production rates.
General Information:
Sequencing and programming may change a bit from manufacturer to manufacturer. In many
cases SBR’s go through the following five modes during normal operations, however storm flow
could significantly change these modes and the time spent in each.
• Fill
• React
• Settling
• Decanting
• Idle (may not happen, especially during high flows)

APPENDIX
The following figure details what you may expect in each of the operational modes
Figure – 1 (SBR Operational Modes)
Influent raw wastewater entering the reactor during this mode,

there may also be periods of mixing without aeration (anoxic) and
mixing with aeration (aerobic). cBOD removal, nitrification and
denitrification may be taking place during this mode. Typically,
Fill you would want raw wastewater (carbon source) for anoxic
biological denitrification periods. No wastewater is being discharged in this
treatment
mode. The amount of time spent in this mode could be dependent
on flow; storm flow could significantly limit the amount of time.
During this mode, there is typically no raw wastewater entering

the SBR (this could be different in storm mode). Periods of
aerobic and anoxic treatment may occur to provide for cBOD
React removal, nitrification and denitrification. No wastewater is being
biological
treatment
discharged in this mode. This is a time for reaction, providing
time for the microorganisms contained in the SBR to consume
and convert the pollutants in the wastewater
During this mode there is typically no wastewater entering or exiting

Settling the SBR. There is no mixing or aeration; it is a quiescent period that
physical treatment
provides for settling of the mixed liquor. In this mode the SBR is
essentially a clarifier.
In the decanting mode, the treated wastewater is decanted from the

reactor and sent on for disinfection. It is typically in this mode that
Decanting sludge is also wasted from the system
physical treatment
As the name suggests, this is a mode where the process is at an idle.

Idle There is no wastewater entering or exiting the system. There may be
some mixing and aeration. The biomass is at endogenous respiration.
endogenous
Some reactors may not have an idle mode or the idle mode may not
phase
be used during wet weather.

APPENDIX
Each of the modes (and SBR tanks) is controlled by some type of computer or Programmable
Logic Controller (PLC). A PLC failure could make it very difficult or impossible to run the
reactor.
Since SBR’s process wastewater batches, the disinfection portion of the treatment plant may
be larger when compared to other facilities of similar size. There may be periods of the day
when no wastewater is being discharged. In some cases, flow equalization (or storage) is
used to buffer the impact of batch discharges; this may be especially true on small sensitive
receiving waters.
Depending on the manufacturer, you may have some flexibility in adjusting batches for
optimization. In any event, high flow or storm mode may present the biggest challenge in
regard to maintaining proper biological treatment and keeping the biomass within the
treatment system. A detailed Wet Weather Operational Strategy should be in place to deal
with high flow conditions. Be sure to review this critical mode and plan of operation with
your engineer and the manufacturer.
Biological Treatment during a Batch

In the previous section we discussed the physical operational phases for a batch reactor. In this
section we will take a closer look at the biological aspects. Keep in mind that the biological
phases may happen multiple times during a complete batch. For the most part, most biological
treatment takes place during the Fill and React cycles. The Settling and Decanting phases of a
batch are a quiescent period of physical treatment that generally does not include much in the
way of biological treatment. The Idle period is a time of endogenous respiration to simply keep
the organisms healthy and active although endogenous decay may occur.
During the Fill and React cycles of the batch, we have biological treatment of wastes with
periods of mixing and aeration (aerobic) and mixing without aeration (anoxic or anaerobic).
This is especially true for systems designed for biological nutrient reduction (BNR). BNR
systems are concerned with reducing the amount of total nitrogen and phosphorus discharged. If
you do not have total nitrogen limits in your permit, it still makes sense to take advantage of the
process of denitrification from a sustainable infrastructure cost savings perspective through the
beneficial uptake of nitrate (produced during nitrification) and the release of alkalinity.
For the purposes of clarification there is also a term known as ENR which simply stands for
enhanced nutrient reduction. ENR facilities typically have multiple stages or phases for greater
reduction of nutrients. Generally, facilities with a limit of <6.0 mg/l N and <0.5 mg/l P fall into
this category.
We will now take a closer look at the following terms

• Anaerobic (mixing without aeration)
• Anoxic (mixing without aeration)
• Aerobic (mixing with aeration)
1. Anaerobic – For the purposes of BNR or ENR, this term SHOULD NOT be confused
with fermentive anaerobic conditions as would be found in anaerobic digestion.

APPENDIX
Anaerobic conditions found in a BNR system are primarily designed to assist with the
removal of phosphorus in the wastewater. In an anaerobic zone or during an anaerobic
cycle, there will be mixing without aeration, we like to see the dissolved oxygen as close
to zero as possible. Nitrates (NO3) will also be depleted. The presence of nitrates or
dissolved oxygen would inhibit the anaerobic process intended to release phosphorus. In
this condition (no dissolved oxygen and no nitrates), the organisms contained in the
biomass release or give up the phosphorus they were holding. There can also be a
significant uptake of cBOD during this process. In most cases, facilities that utilize
biological means (BNR or ENR) for phosphorus removal also have a chemical means for
the removal of phosphorus as well.
* Mixing without aeration.
* Release of phosphorus.
* Uptake of cBOD.
* No dissolved oxygen or nitrates.
2. Anoxic – Similar to anaerobic as we have mixing without aeration. The primary purpose
in this cycle is for denitrification (conversion of nitrate to nitrogen gas). In order for
denitrification to take place, we must have nitrates present. In this case, facultative
organisms search for another electron acceptor (such as nitrate) for respiration. As with
the anaerobic zone, we want to deplete elemental oxygen (DO). We want DO levels to be
as close to zero as possible (< 0.3 mg/l). In a flow through system, there would be a
nitrate recycle from the aerobic zone. In the case of a batch reactor, the anoxic period
would come after a period of nitrification (aerobic) so nitrates would be present. You will
also experience the release of alkalinity during proper denitrification. The facultative
organisms also need a carbon source such as raw wastewater we therefore may see this
cycle taking place during the fill cycle for a batch reactor. Carbon can also come from
endogenous decay or through an added source such as methanol. As nitrates are depleted,
we may automatically slip into an anaerobic mode (given enough time).
* Mixing without aeration.
* Consumption of nitrates (NO3), release of nitrogen gas (denitrification)
* Uptake of cBOD.
* Release of alkalinity (about 3.6 lbs/ per lb of nitrate converted to nitrogen)
* Carbon source needed for denitrification.
Note: While DO probes are effective at monitoring oxygen levels during the aeration
phase, ORP probes should be used to monitor conditions during the anaerobic and
anoxic phases due to the nearly negligible levels of oxygen present.
3. Aerobic – During this period we have mixing and aeration. We typically like to see
dissolved oxygen levels of greater than 2.0 mg/l to sustain nitrification. In this process we
can consume any remaining cBOD, achieve nitrification (conversion of ammonia
nitrogen to nitrate nitrogen) and we will also have a beneficial uptake of phosphorus
through phosphorus accumulating organisms (PAO’s). As you may recall from the
anaerobic cycle, phosphorus is released by the organisms during times of oxygen
deprivation. When exposed to aeration, the organisms take back all the phosphorus they
gave up plus a bit more. This phenomenon is known as luxury uptake of phosphorus. In
this cycle we also can achieve nitrification. The process of nitrification is purely aerobic
and requires a large volume of dissolved oxygen and alkalinity. It takes approximately
APPENDIX
4.6 lbs of dissolved oxygen and 7.2 lbs of alkalinity to convert one pound of ammonia
into nitrate. The use of ORP probes can be helpful in determining when biological cycles
are complete.
* Mixing with aeration
* Nitrification (converting toxic ammonia into nitrate)
* Luxury uptake of phosphorus through PAO’s
* DO typically greater than 2.0mg/l but not greater than 4.0 mg/l
* Consumption of alkalinity (for nitrification)
* Consumption of large volumes of oxygen (for nitrification)
The process of nitrification, denitrification and phosphorus removal requires close operator input
and scrutiny. The scope of this document provides only a brief overview of these topics. It is
essential for all operators of activated sludge systems to become familiar with the principles of
nitrification, denitrification and phosphorus removal. It should be noted that partial nitrification
or partial denitrification could lead to the production of nitrite (NO2) that could in turn produce
problems with wastewater disinfection. Due to the large volume of alkalinity consumed during
nitrification, pH values could also drop suddenly. As a rule of thumb, you would like to see
about 100 mg/l of alkalinity left over after complete nitrification. Alkalinity concentration of less
than 50 mg/l could lead to significant problems and the loss of nitrification.
While the reduction of nutrients is desirable in many wastewater effluent streams, you need to
keep in mind that there is a fundamental requirement for nutrients in order for biological
wastewater systems to function properly. The rule is you need one pound of phosphorus and 5
pounds of nitrogen for every 100 lbs of incoming BOD.
1(P):5(N):100(BOD) Rule. In most cases, municipal wastewater systems have adequate
nutrients. Some industrial sources with high BOD loading (with low nutrients) can cause a
problem.
SBR Operations and Maintenance

ALL wastewater systems need to develop and implement an operations and maintenance
plan that provides for sustainable infrastructure and includes the following major
categories.
a. Process control
b. Wet weather operations plans and strategy
c. Solids handling and management
d. Preventative and emergency maintenance
e. Energy Efficiency
f. Security and emergency planning
g. Facility safety (included with all aspects)
To further detail, a good operations and maintenance plan is well documented, easy to follow
and should contain the following elements at a minimum;
1. A description of average, seasonal or diurnal characteristics of the influent wastewater

and trucked in wastes.

APPENDIX
2. A flow schematic of all processes (including recycle, supernatant or filtrate flows).
3. Identification of each individual treatment unit and an assessment of its criticality.

Consider reducing criticality of key processes that could jeopardize the entire treatment
process. For SBR systems the computer or PLC that controls the system is mission
critical. You should be able to replace or re-program in short order.
4. The normal operating ranges and expected removal efficiencies of each treatment unit.
5. Identification of sampling points, methods and calculations to be used to make process

control adjustments and a schedule for carrying out these process control operations.
6. A plan for monitoring all treatment units. This includes identifying parameters to be
monitored and action plans when trigger levels for parameters are reached.
7. Any standard operating procedures and guidelines to maintain permit compliance.
8. Identification of key processes and equipment and an outline of how key processes will
be monitored and adjusted during times the operators may be absent or unable to
personally monitor the key process. (*Note – A key process is any process that should it
fail will or may cause harm to human or environmental health)
9. A preventative and emergency maintenance plan for all process equipment including an
inventory of essential spare parts and methods for emergency repairs in accordance with
manufacturer’s recommendations. Said plans should contain emergency contact
information for selected contractors, equipment manufacturers and vendors. The plan
should contain scheduling of routine maintenance and tracking of all equipment
maintenance. The use of elapsed time meters can assist with scheduling of maintenance
and also in the identification of unusual conditions. Detailed procedures should be
identified for maintenance personnel to follow to ensure compliance with manufacturer
recommendations. Safety procedures should also be detailed.
10. Security and emergency response plans that cover both man-made and natural disasters
that may impact the facility.
11. Identification and mitigation of actual and potential hazards. Establish procedures to
ensure safety of plant personnel and visitors for all aspects of operation and maintenance.
This includes the use of appropriate PPE.
12. A wet weather operational strategy that maximizes the flow through the treatment plant
while minimizing the washout of biological solids from the system. This may include
programming changes for wet weather events, work closely with you engineer and
manufacturer to optimize batch settings. This could include the placement of current
density baffles or the use of polymers.
13. A solids management plan that details how sludge and other treatment residues will be
wasted, treated, handled and disposed of during times of normal operation as well as
during times of adversity.
APPENDIX
14. A daily checklist should be developed that the facility operators use to monitor all
treatment processes. Any unusual conditions should be noted and addressed as soon as
possible
15. A communications scheme that allows the operators to convey essential information to
the system owners in regard to compliance status.
16. Monitoring of utility usage (such as electrical energy, natural gas, water). Implement
strategies for energy savings where applicable.
• ALL key processes should be monitored and connected to an alarm dialer that activates
and notifies operator of the problem.
SBR Specific Process Control Issues

Due to the fact an SBR processes wastewater in batches, there are some considerations with
regard to process control. All treatment systems (including batch reactors are impacted by
diurnal changes in flow and strength of wastewater. Operators must be familiar with these
impacts. As previously mentioned, wet weather operations will present some of the biggest
challenges.
The specific issue here is that the water level (mixed liquor) is variable based upon the mode,
time of day and other factors. In a conventional flow through plant the water level always
remains basically the same. In a batch reactor if you measure the MLSS at 8ft depth and then
again at 12ft, the concentration of the MLSS will change. The MLSS reading needs to
correlate to the depth of the tank and must be taken during a time of mixing and/or aeration.
When calculating an F/M Ratio you would need to know the depth of the reactor and the
MLSS in order to calculate the pounds of solids under aeration. The following example takes
a hypothetical treatment plant and calculates the F/M Ratio.
Example 1 - F/M Calculation for SBR
Details – 2 Unit SBR @50 ft long 15 ft wide and a maximum SWD of 14ft
Minimum discharge depth 8ft SWD
50 X 15 X 14 = 10,500 cubic feet (max) X 7.48 = 78,540 gal max
Total plant daily flow = 0.25 MGD, Influent BOD = 200 mg/l
.25 X 200 X 8.34 = 417 lbs of BOD, ½ the flow going to each unit 208 lbs (F) each
Unit 1 had a MLSS concentration of 3500 mg/l with a SWD of 12 ft

50 X 15 X 12 = 9000ft cu ft. X 7.48 = 67,320 gallons or .06732 million gallons
.06732 X 3500 X 8.34 = 1965 lbs of solids under aeration (M)
(F)208/(M)1965 = 0.1 F/M
Unit 2 had a MLSS concentration of 3000 mg/l with a SWD of 14 ft

50 X 15 X 14 = 10,500 cu ft. X 7.48 = 78,540 gal or .07854 million gallons
.07854 X 3000 X 8.34 = 1965 lbs of solids under aeration(M)
(F)208/(M)1965 = 0.1 F/M

APPENDIX
The use of a centrifuge can help you estimate the MLSS concentration.
The desired F/M ratio for many SBR systems ranges between. 0.04 – 0.10. Please refer to
your facility Operations and Maintenance Guide for specific F/M information for your
system. Your engineer as well as the manufacturer will be able to provide you guidance in
achieving the desired F/M. As the operator, you may determine the optimum F/M for your
facility based on operational process control records and reports.
Some conventional activated sludge plants use a constant MLSS concentration as a means of
process control. Since your side water depth (SWD) changes, you will have to maintain
certain number of lbs under aeration as opposed to a constant MLSS.
The same issue (in regard to side water depth) applies when doing a 30 minute settleability
test. You should take this sample at the same SWD each day while aeration and mixing are
occurring. If you are calculating an SVI the same applies.
SBR Effluent Sampling Issues

Since an SBR discharges in batches, collecting a 24hour/effluent composite sample is a little
more difficult. There will be times during the day that there is no discharge. Your sampling
device should be tied to a flow meter that collects a sample after every “X” amount of
gallons. For example, we could program the sampler to take a 100 ml sample for every 1000
gallons discharged. If you do not have a composite sampler that is tied to a flow meter, you
need to get one. In the interim you could manually collect a composite sample by grabbing a
sample during the start of the discharge cycle, the middle of the discharge cycle and one at
the end of the discharge cycle (at a minimum) for each batch discharged for that day. Please
refer to your facility NPDES permit for specific sampling requirements. Remember that your
samples must be representative of the nature and volume of wastewater you are discharging.
ALL samples for DMR reporting must be performed by an accredited laboratory.
On-Line instrumentation for SBR’s

The use of on-line continuous monitors can greatly enhance the operator’s ability to properly
operate and maintain an SBR process, especially for facilities that are achieving nitrification
and denitrification (BNR). On-line continuous monitoring instruments can provide feedback
to a control panel (for operator interpretation) or they can be hooked up to the facility
computer or PLC to change the aeration and mixing cycles to optimize nitrification and
denitrification. The use of these instruments will add to the sustainability of the infrastructure
by;
• Improving effluent water quality

• Help control filamentous organisms – better sludge settling
• Reduced sludge production
• Increasing Energy Efficiency (reducing un-needed aeration, enhanced uptake of NO3).
• Reduce or eliminate the need to add supplemental alkalinity

APPENDIX
Even if you facility does not have requirements for total nitrogen, the use of denitrification in the
treatment cycle can result in a significant savings.
Recommended on-line measurement instrumentation includes:

• Oxidation Reduction Potential (ORP)
• Dissolved Oxygen (DO)
• Nitrate (NO3)
• Ammonia-Nitrogen (NH3-N)
• pH
The above are recommended as a minimum for proper process control, additional probes or
instruments can be added based upon the needs of your specific site. Speak to your engineer and
manufacturer for details about your facility needs. As with any instrumentation proper care and
calibration is essential.
Please review with your engineer and the manufacturer for the optimal array of instrumentation
for your operating conditions.
Figure – 2
This illustrates how the use of ORP can

determine treatment cycles. This is
especially true for nitrification and
denitrification.
Recommended Process Control Tests, Observations and Calculations
The following is suggested for proper process control. The actual testing you do and how
frequently you do it will be based upon your circumstances. If you are not sure, consult your
engineer and state regulatory officials. It is important that you do testing on the influent
wastewater so you can determine loadings and efficiencies of all treatment units. Influent
testing also provides valuable information for chapter 94 reports as well. At a minimum you
should test your influent wastewater each time you collect samples for effluent testing
(NPDES Reporting). The operator should also note weather conditions on a daily basis Hi/Lo
temperature and amount (if any) precipitation.
The following describes the parameters you should be monitoring (at a minimum) in regard
to influent wastewater. Depending on your facility, additional parameters may need to be
monitored especially if you facility treats industrial or trucked in waste.
APPENDIX
Influent Wastewater Recommended Parameters

cBOD 24 Hour Composite
Total Suspended Solids (TSS) 24 Hour Composite
Ammonia-Nitrogen (NH3-N) 24 Hour Composite
PO4 24 Hour Composite
pH Grab
Temperature Grab
Alkalinity Grab
Flow (MGD) Continuous monitoring
Visual/Aromatic Observations Document unusual conditions
For monitoring the SBR’s, the following are the monitoring parameters, calculations and
observations you should institute. The frequency of these will depend on the variability of
your waste-stream and other factors. Refer to “SBR Specific Process Control Issues” when
sampling, testing or performing calculations on an SBR
Best done with continuous monitoring

Dissolved Oxygen within the reactor. Calibration of DO
sensors should be checked weekly.

Oxidation Reduction Potential (ORP) within the reactor.

Nitrate (NO3) within the reactor. Occasional grabs (to
check calibration) during each cycle.
Can be a grab sample at various intervals. If

you are having problems maintaining
Nitrite (NO2) chlorine residual excess nitrite can be a
factor. Nitrite can be associated with
incomplete nitrification or incomplete
denitrification

Ammonia-Nitrogen (NH3-N) within the reactor. Occasional grabs (to
check calibration) during each cycle.
This test is essential for determining the lbs

of solids you have under aeration. The use
MLSS & MLVSS of a centrifuge spin can provide quick and
reasonable estimates of solids under
aeration. With an increase in MCRT, the
MLVSS should
decrease.

APPENDIX
Mean Cell Residence Time MCRT is a calculation.

lbs of solids in the system
Solids leaving the system (WAS & Effluent)
F/M is a calculation (be aware of SWD).

Food to Microorganism Ratio FOOD (BOD) coming into system
lbs of solids under aeration
SVI is a calculation
Sludge Volume Index (SVI) 30 Minute Settleability Result ml/l
MLSS mg/l / 1000
Microscopic observation of the biomass to

Microscopic Examination determine the relative predominance of
organisms and to spot troublesome
filamentous organisms.
To help quantify the amount of sludge in the

system and to determine settling
characteristics. Must be used in conjunction
30 Minute Settleability with MLSS to determine SVI. Remember to
account for your side water depth. Best
taken towards the end of the React cycle.
This can be a grab sample, should not drop

below 50 mg/l at any point in the system
especially for facilities that must nitrify.
Would like to see 100 mg/l in effluent after
Alkalinity complete nitrification.
This can be done through continuous

monitoring or through a grab sample.
pH Alkalinity in more important. Drastic
changes in pH will occur when alkalinity is
consumed.
The temperature will determine how lively your
biological activity will be every 10 degree C
Temperature change in temperature results in biological
activity either doubling (warmer temps) or
cutting in half (for colder temps).

APPENDIX
Useful test for determining the respiration

Dissolved Oxygen Uptake rate of the biomass. Can be used to
Rate(DOUR) determine treatability of waste.
We must be able to quantify the amount of

Amount and concentration of sludge removed from the system in order to
sludge wasted from each SBR maintain a proper mass balance.
This could include flows such as supernatant

from aerobic digesters or filtrate from
Recycle flows dewatering or thickening activity. These
recycle flows can be high in nutrients
(phosphorus and nitrogen) as well as BOD
SBR Daily Checks and Activities
All treatment plants should be checked on a daily basis. The following is a (minimum) list of
items that should be checked on a daily basis.
1. Upon arrival, check condition of gates fences and doors be sure facility is secure when
you arrive and again when you leave. If there are any signs of tampering or break-ins,
notify law enforcement immediately.
2. Check operation of blowers and mixing equipment. Assure all equipment is working
properly.
3. Check operation of computers or PLC
4. Check operation of decanting mechanisms and float switches (if any).
5. Perform any routine maintenance that may be required (as determined by manufacturer’s
recommendations).
6. Perform daily lab work and calculations (as well as any process control testing,
calculation or observation that may be due), adjust or fill chemical feeders as needed.
7. Check condition of disinfection system for proper operation
8. Check operation of pumps.
9. Pay attention to any unusual odors, noises or characteristic of wastewater, note and
investigate unusual items.
10. Immediately notify the system owner of any real or potential problem that is or may
cause permit violations
11. Thoroughly document activities. Graph results of sampling and calculations for easy
interpretation.
If you are using chlorine for disinfection, you should use a sludge judge (or similar device) to
determine the accumulation of sludge in the contact tanks on a weekly basis. Excess solids in
the chlorine contact tanks must be removed.

APPENDIX
Other Useful Information

Operator of SBR’s must be thoroughly familiar with the activated sludge process. This
includes the process of nitrification, denitrification and phosphorus removal. DEP has
training modules and videos that can provide useful information in regard to proper operation
of activated sludge systems.
• DEP DVD – Intro to activated sludge, nitrification, denitrification and chemical feed
systems.
• DEP wastewater training modules 8,12,15,16,17,18
• There are also a number of other texts available in regard to activated sludge,
nitrification, denitrification, phosphorus removal and BNR from the Water
Environment Federation (WEF) and many other private vendors,


Design Aeration1

Uploaded by

Copyright:

Available Formats

Design Aeration1

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Design Aeration1

Uploaded by

Copyright:

Available Formats

Wastewater Treatment Plant

Operator Certification Training

Unit 1 – Modifications of the Conventional Activated Sludge Process

I. Review of the Conventional Activated Sludge Process

II. Reasons for Modifying the Conventional Activated Sludge Process

III. Common Modifications of the Activated Sludge Process

Unit 2 – The Sequencing Batch Reactor (SBR)

I. Description of the SBR Processes

II. Configuration of the SBR System

Bureau of Safe Drinking Water, Department of Environmental Protection i

III. Operation of SBRs

Appendix – Sustainable Infrastructure Wastewater Operations Informational Sheet; “Sequential Batch

Bureau of Safe Drinking Water, Department of Environmental Protection ii

Bureau of Safe Drinking Water, Department of Environmental Protection 1-1

Bureau of Safe Drinking Water, Department of Environmental Protection 1-2

Key Process Design Parameters

F/M Ratio*.................................................................................................... 0.2 - 0.5 #BOD / #MLVSS / day

Organic Loading (maximum) ....................................................................... 40 #BOD / 1,000 cubic feet / day

MLSS ........................................................................................................... 1000 – 3000 mg / liter

Aeration Retention Time (minimum)** ......................................................... 6 hours

Solids Recycle Rate** .................................................................................. 15% – 100%

*F/M = food to microorganism ratio

Bureau of Safe Drinking Water, Department of Environmental Protection 1-3

Figure 1.1 Schematic Drawing of a Conventional Activated Sludge System

Bureau of Safe Drinking Water, Department of Environmental Protection 1-4

• Increasing organic loading.

• Providing additional nutrients required for proper treatment.

• Accommodating flow rate or organic loading that varies seasonally.

• Achieving nutrient removal.

Economic and Labor Benefits

Bureau of Safe Drinking Water, Department of Environmental Protection 1-5

• BOD is first adsorbed by the microorganisms.

• BOD is then metabolized by the microorganisms for energy and growth.

A Contact Tank is used for aeration of the mixed liquor.

• Influent or primary clarifier effluent is added to the contact tank.

• Residence time in the contact tank is approximately 30 to 90 minutes.

• The treatment cycle then restarts.

• Residence time in the stabilization tank is approximately 4 to 6 hours.

Bureau of Safe Drinking Water, Department of Environmental Protection 1-6

Key Process Design Parameters

F/M Ratio*.................................................................................................... 0.2 - 0.6 #BOD/#MLVSS/day

Organic Loading (maximum) ....................................................................... 60 #BOD/1,000 cubic feet/day

MLSS ........................................................................................................... 1000 – 3000 mg/liter

Aeration Retention Time (minimum)**ŧ ......................................................... 5 hours

Solids Recycle Rate** .................................................................................. 50% – 150%

*F/M = food to microorganism ratio

• Primary effluent is introduced into the Contact Zone.

• A stabilization tank is added to stabilize the adsorbed organics.

Bureau of Safe Drinking Water, Department of Environmental Protection 1-7

Figure 1.2 Schematic Drawing of a Contact Stabilization System3

Bureau of Safe Drinking Water, Department of Environmental Protection 1-8

• Retention time in the reaeration tank is approximately 24 hours.

Key Process Design Parameters

F/M Ratio*.................................................................................................... 0.3 - 0.8 #BOD/#MLVSS/day

Organic Loading (maximum) ....................................................................... 70 #BOD/1,000 cubic feet/day

MLSS ........................................................................................................... 1000 – 2500 mg/liter

Aeration Retention Time (minimum) ............................................................ 4 hours

Solids Recycle Rate** .................................................................................. 15% – 100%

ŧ Does not consider the reaeration tank