MN217 Fluids Mechanics II 1 PDF

NATIONAL UNIVERSITY OF ENGINEERING
COLLEGE OF MECHANICAL ENGINEERING
MECHANICAL-ELECTRICAL ENGINEERING PROGRAM
MN217 – FLUID MECHANICS II
I. GENERAL INFORMATION
CODE : MN-217 FLUID MECHANICS II

SEMESTER : 5
CREDITS : 3
HOURS PER WEEK : 4 (2 Theory – 2 Practice)
PREREQUISITES : MN-216. Fluid Mechanics I
CONDITION : Mandatory
II. COURSE INTRODUCTION
The Fluid Mechanics II is a subject of theoretical and practical nature. The subject
begins with the study Internal Flow Study: Loss of energy in pipes and fittings,
pipeline circuit in series and in parallel, pumping system and use of spreadsheets; Is
continued with Bundary Layer Theory: laminar boundary layer equations, turbulent
boundary layer and applications in engineering; Then the Compressible Flow
Dynamics: Adiabatic Flow, Shock Wave, Nozzles and Diffusers, Fano Flow and
Rayleigh Flow; Is followed by the Study of External Flow: Introduction to
Aerodynamics; To finally treat the Natural Gas Transportation: Application of the NTP,
ASME B31.8 standards and use of spreadsheet for the design and calculation of
external network and internal network of natural gas.
III. COURSE OUTCOMES
At the end of the course, the students will be able to:

1. Design liquid transport systems using national (NTP) and international standards
(ASME B31.8) and consideration of the technical-economic criteria and
protection of the environment. Evaluate the use of material for pipes, fittings,
valves, measurement units and flow control. Select the drive, pump and engine
team reflecting on existing literature and the experience of other engineers to
make your project successful.
2. Use boundary layer theory in river, sea, land and air vehicles to:
• Determine the drag forcé by action of the fluid.
• Determine the power of the motor to be used.
• Organize flow simulaton in FLUENT software.
3. Design converging nozzles and divergent converging nozzles for industrial use,
reflecting on the use of thermodynamic processes.
1
4. Design Natural Gas Transportation System, making use of NTP and relevant
international standards justifying the use of materials in tubes, environmentally
friendly accessories.
5. las estaciones de compresión y considera el impacto de las actividades de la
ingeniería sobre su entorno.
IV. LEARNING UNITS
1. STUDY OF INTERNAL FLOW / 12 HOURS

Primary Loss and Secondary Losses / Series and Parallel Piping Systems /
Applications and use of spreadsheet / Economic Diameter / Design of pumping
systems.
2. BUNDARY LAYER THEORY / 8 HOURS

Definition. Main equations / laminar boundary layer. / Boundary layer Thickness /
Von Karman momentum equation / Turbulent regime boundary layer /
Applications.
3. FLUJO COMPRESIBLE UNIDIMENSIONAL / 18 HOURS
Introducción. Velocidad del sonido. Número de Mach Estados de referencia / Flujo
Adiabático Irreversible con área variable, Flujo Adiabático Reversible y Flujo
másico / Flujo en toberas y difusores. Eficiencia térmica / Aplicaciones / Ondas de
choque / Funcionamiento de tobera subsónica y supersónica / Aplicaciones. Flujo
fanno y flujo Rayleigh / introducción a la aerodinámica. Entrega de la monografía
Sistema de Bombeo.
4. ESTUDIO DEL TRANSPORTE DE GAS NATURAL / 8 HOURS
Propiedades del Gas natural /Instalaciones Industriales. Red interna /
instalaciones Industriales Red Externa / Aplicaciones. Entrega de la monografía
Transporte de Aire Comprimido.
oratori1: Banco de Tuberías.
.
V. METHODOLOGY
The course is developed in sessions of theory, practice and laboratory. In theory

sessions, the teacher informs on concepts and applications. In the practical sessions,
various problems are solved and analyze their solution and reflect on their use in other
contexts.
The student must present and expose an integrative project: in the middle and at the
end of the course. In all sessions, the active participation of the student is promoted
and the cooperative work is used.
VI. EVALUATION FORMULA
Evaluation System "F". Calculation of the Final Average:

FA = (ME + 2FE + PP) / 4
ME: Midterm Exam EF: Final Exam PP: Average of qualified practices
The average of qualified practices (PP) is the arithmetic average of the 3 highest marks
of the qualified practices
VII. BIBLIOGRAPHY
[1] POTTER C. Merle y WIGGERT C. David. Mecánica de Fluidos Cuarta edición.

México, International Thomson Editores, S.A. de C.V., 2015.
[2] MOTT Robert L. Mecánica de Fluidos Séptima edición. México, PEARSON

EDUCACIÓN, 2015.
[3] NTP 110. NTP 111. ASME B31.8
Lima, August 2016
* Incluir de preferencia dos textos (no más de tres) y en lo posible libros de referencia
mundial.
IMPORTANTE Enviar el formato al email: acreditacionfim@uni.edu.pe

MN217 Fluids Mechanics II 1 PDF

Uploaded by

Copyright:

Available Formats

MN217 Fluids Mechanics II 1 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

MN217 Fluids Mechanics II 1 PDF

Uploaded by

Copyright:

Available Formats

NATIONAL UNIVERSITY OF ENGINEERING

COLLEGE OF MECHANICAL ENGINEERING

MECHANICAL-ELECTRICAL ENGINEERING PROGRAM

MN217 – FLUID MECHANICS II

CODE : MN-217 FLUID MECHANICS II

II. COURSE INTRODUCTION

III. COURSE OUTCOMES

At the end of the course, the students will be able to:

1. STUDY OF INTERNAL FLOW / 12 HOURS

2. BUNDARY LAYER THEORY / 8 HOURS

The course is developed in sessions of theory, practice and laboratory. In theory

VI. EVALUATION FORMULA

Evaluation System "F". Calculation of the Final Average:

[1] POTTER C. Merle y WIGGERT C. David. Mecánica de Fluidos Cuarta edición.

[2] MOTT Robert L. Mecánica de Fluidos Séptima edición. México, PEARSON

Lima, August 2016

You might also like