Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 99 views

    Accelerator Control System

    Uploaded by

    Napi
    This document provides instructions for removal, installation, and inspection of an accelerator control system. It includes an exploded view diagram labeling the main components. The removal process involves disconnecting the accelerator pedal position sensor harness connector and loosening mounting bolts to remove the accelerator pedal assembly. Installation is the reverse of removal, making sure to insert the locating pin and hook properly. Inspection after installation includes checking pedal movement and fully released position, as well as electrical inspection of the position sensor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Accelerator Control System

    Uploaded by

    Napi
    99 views3 pages
    This document provides instructions for removal, installation, and inspection of an accelerator control system. It includes an exploded view diagram labeling the main components. The removal process involves disconnecting the accelerator pedal position sensor harness connector and loosening mounting bolts to remove the accelerator pedal assembly. Installation is the reverse of removal, making sure to insert the locating pin and hook properly. Inspection after installation includes checking pedal movement and fully released position, as well as electrical inspection of the position sensor.

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides instructions for removal, installation, and inspection of an accelerator control system. It includes an exploded view diagram labeling the main components. The removal process involves disconnecting the accelerator pedal position sensor harness connector and loosening mounting bolts to remove the accelerator pedal assembly. Installation is the reverse of removal, making sure to insert the locating pin and hook properly. Inspection after installation includes checking pedal movement and fully released position, as well as electrical inspection of the position sensor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    99 views3 pages

    Accelerator Control System

    Uploaded by

    Napi
    This document provides instructions for removal, installation, and inspection of an accelerator control system. It includes an exploded view diagram labeling the main components. The removal process involves disconnecting the accelerator pedal position sensor harness connector and loosening mounting bolts to remove the accelerator pedal assembly. Installation is the reverse of removal, making sure to insert the locating pin and hook properly. Inspection after installation includes checking pedal movement and fully released position, as well as electrical inspection of the position sensor.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 3

    ENGINE

    ACCELERATOR CONTROL SYSTEM


    SECTION ACC ACC

    E
    CONTENTS
    PRECAUTION ............................................... 2 ACCELERATOR CONTROL SYSTEM .............. 3 F
    Exploded View .......................................................... 3
    PRECAUTIONS ................................................... 2 Removal and Installation .......................................... 3
    Precautions for Removing Battery Terminal ............. 2 Inspection ................................................................. 3 G
    REMOVAL AND INSTALLATION ................ 3
    H

    Revision: 2014 April ACC-1 AD0


    PRECAUTIONS
    < PRECAUTION >
    PRECAUTION
    PRECAUTIONS
    Precautions for Removing Battery Terminal INFOID:0000000010041534

    • When removing the 12V battery terminal, turn OFF the ignition
    switch and wait at least 30 seconds.
    NOTE:
    ECU may be active for several tens of seconds after the ignition
    switch is turned OFF. If the battery terminal is removed before ECU
    stops, then a DTC detection error or ECU data corruption may
    occur.
    • For vehicles with the 2-batteries, be sure to connect the main bat-
    tery and the sub battery before turning ON the ignition switch.
    NOTE:
    If the ignition switch is turned ON with any one of the terminals of
    SEF289H
    main battery and sub battery disconnected, then DTC may be
    detected.
    • After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
    NOTE:
    The removal of 12V battery may cause a DTC detection error.

    Revision: 2014 April ACC-2 AD0


    ACCELERATOR CONTROL SYSTEM
    < REMOVAL AND INSTALLATION >
    REMOVAL AND INSTALLATION A
    ACCELERATOR CONTROL SYSTEM
    Exploded View INFOID:0000000010041535
    ACC

    JPBIA3364GB
    H
    Accelerator pedal assembly Brake pedal bracket
    Locating hook Locating pin
    I
    : N·m (kg-m, in-lb)

    Removal and Installation INFOID:0000000010041536


    J

    REMOVAL
    1. Disconnect accelerator pedal position sensor harness connector. K
    2. Loosen mounting bolts, and remove accelerator pedal assembly.
    CAUTION:
    • Never disassemble accelerator pedal assembly. Never remove accelerator pedal position sensor
    L
    from accelerator pedal assembly.
    • Avoid impact from dropping etc. during handling.
    • Be careful to keep accelerator pedal assembly away from water.
    M
    INSTALLATION
    Note the following, and install in the reverse order of removal.
    • Insert the locating pin while inserting the locating hook in to the break pedal bracket. Tighten mounting bolts
    to accelerator pedal assembly. N
    CAUTION:
    • Never squeeze the locating hook into the break pedal bracket when inserting the locating pin into
    the hole on the brake pedal bracket side. O
    • When harness connector of accelerator pedal position sensor is disconnected, perform “Accelerator
    Pedal Released Position Learning”. Refer to HR12DE EC-93, "Work Procedure".
    Inspection INFOID:0000000010041537 P

    INSPECTION AFTER INSTALLATION


    • Check accelerator pedal moves smoothly within the whole operation range when it is fully depressed and
    released.
    • Check accelerator pedal securely returns to the fully released position.
    • For the electrical inspection of accelerator pedal position sensor. Refer to EC-222, "Component Inspection",
    EC-225, "Component Inspection" and EC-231, "Component Inspection".

    Revision: 2014 April ACC-3 AD0

    You might also like