Data Sheet: PART NO. 632 858

DATA SHEET
PART NO. 632 858

CAR TOP
SAFETY SYSTEM
§ Provides an output that can be used to stop the lift safely during a car-top intrusion
or machine room intrusion (optional)
§ Greatly reduces the risk of accidents
§ Designed for new and existing lifts
§ Deters intruders
§ Quick and easy to fit to any type of lift
§ Cost effective solution
INTRODUCTION
The Surfguard has been developed as a safety system
to detect intruders on the top of a lift car. On detection
of an intruder, the unit provides an output that can be
used to stop the lift running. In addition, outputs are
provided to operate a beacon and siren. An auxiliary
output is also available for remote alarm indication.
OPERATION AND INSTALLATION

The Surfguard is a dual passive infra-red detector
system, which provides an horizontal and vertical field
of view on the car top area, as shown in Fig 1. It is
sensitive to changing thermal images and it will detect
a person attempting to jump onto the car top. There
is also a vertical sensor wired into the horizontal
detector (shown in Fig 1) to sense any object being
thrown over the detection devices from above.
The horizontal detection device is hinged and can be

raised or lowered by approx ±15º to allow coverage of
the lift roof, without detecting the far wall.
The dual detection device is housed on a robust fixing

bracket assembly, elevated by an adjustable stand
(Fig 2). This is positioned on the left front corner of
the lift car top near the door operator and securely
fixed by self-tapping screws. If there is no suitable
position for the stand to be fitted, the inner section
can be secured independently, using the 8 slots and Fig 1: Typical Surfguard installation on lift top
fixing kit provided. The stand allows for height
adjustments to suit site conditions.
room. The Surfguard controller is housed in a robust
The system is armed and disarmed through a remote metal casing and can be supplied with 110/240V AC
key switch, which is encased in a flanged box with a or 15/35V DC. The removable terminal blocks allow
DATASH34/SPA/14.07.99
2-core 2m cable, so it can be fitted separately from easy wiring installation. The beacon and thesiren can
the control unit. The control unit is mounted on the be installed on the car top, or at the top of the lift
car top, or in a remote location, such as the machine shaft.
MEMCO LTD, CLYDE HOUSE, REFORM ROAD, MAIDENHEAD, BERKSHIRE, SL6 8BY, UK. Tel +44 (0)1628 770734 Fax +44 (0)1628 621947 www.memco.co.uk
CONTROLLER CONNECTIONS (see Fig 3)
n Input DUAL DETECTION
DEVICE
Four different inputs are available, two of which are
used to monitor the dual detection device and the VERTICAL SENSOR
vertical sensor. Each detector head is connected by
a 2.7m cable with 3 cores plus a screen. Each core
is terminated using boot-lace ferrules. The cores carry
+12V DC, 0V, and the trigger output (PNP-N/C).
The “Door” input is used to detect machine room door

access through a door sensor (optional). An auxiliary
input is also provided to allow the sensing of other
security devices, if required.
n Output
Three different relays are programmed to operate a
number of devices after a detection:
§ The main trigger relay is connected to the lift FIXING
controller, and is used to stop the lift BRACKET
immediately and safely.
§ A dual pole relay is used to trigger the beacon
and the auxiliary output (providing, for example,
information to a remote control centre). The red
beacon uses the 12V DC supplied by the ADJUSTABLE
controller. Its nominal power is 3W and it is STAND
fully protected to IP65.
§ The siren relay is used to trigger the siren. The
sound output of the supplied siren is 85dbm.
This peripheral device also uses the 12V DC
supplied by the Surfguard controller. An
adjustable cut-off timer, pre-settable from 45
secs to 5 minutes, is available in the controller.
Note: If the controller installation is to be in the

machine room, please ensure that you have
sufficient spare cores in the travelling cable.
ON SITE ADJUSTMENT
The Surfguard system alarm characteristics can be
configured on site to suit local conditions, using the
4 system delay potentiometers. FIXING HOLES
STAND BASE
§ Arming Delay
The arming delay of 5sec-50sec allows the lift
engineer to arm the system through the Fig 2: Surfguard dual detection device on adjustable stand
controller key switch positioned on the car top.
The delay allows him to leave the protected
area, without triggering the Surfguard during the § Alarm Delay (Machine Room Door)
delay period. The machine room door switch delay of 1sec-
45sec allows the lift engineer to arm or disarm
§ Alarm Delay (infra-red system) the system through the controller key switch,
The alarm delay of 1sec-45sec allows the lift when the controller is positioned in the machine
engineer to disarm the system, via the controller room, without triggering the Surfguard system.
key switch, without activating the peripheral
devices. § Siren Timeout
The siren timeout gives a time delay of between
45sec-5min before the siren is muted. This
delay allows the siren to be deactivated but
the beacon to carry on flashing, after an alarm
has occurred.

Data Sheet: PART NO. 632 858

Uploaded by

Copyright:

Available Formats

Data Sheet: PART NO. 632 858

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Data Sheet: PART NO. 632 858

Uploaded by

Copyright:

Available Formats

DATA SHEET

PART NO. 632 858

OPERATION AND INSTALLATION

The horizontal detection device is hinged and can be

The dual detection device is housed on a robust fixing

The “Door” input is used to detect machine room door

Note: If the controller installation is to be in the

You might also like