ELECTRICAL SAFETY

for Household Consumers

BY:

ENGR. REGINALDO N. MARINAY,

REE, RMP
PRESIDENT, POWERHOUSE REVIEW AND
TRAINING CENTER
Effects of Electricity on Human
Body
Why Worry About Electricity?
Electrocutions rank fourth in causes
of industrial fatalities (behind traffic,
violence and construction). It is
estimated that 600 people die every
year of electrical causes. Most of
these accidents involve low voltage
(600 volts or less).
2
Graphs

Electricity flowing through the

human body can shock, cause
involuntary muscle reaction,
paralyze muscles, burn tissues and
organs or kill. In case of electric
shock, the amount of current flow
through the body and the
corresponding body sensation are
identified in the following graph.
3
4
Graph: Electric Shock Vs.
Body Sensation

A small night-light with a 6-watt

bulb draws 0.05 ampere, and even
that small amount of current can
be fatal. Here are some effects of
current (in milli amps) passing
through a 150 pound body (note
that perception is only 0.5 to 1.5
milli amps).
5
6
Current passing through your body can
cause electric shock, resulting in 3 types of
potential injuries:
Burns (arcs burn with heat and radiation)
Physical injuries (broken bones, falls and
muscle damage) – at 10 milli amps, the
muscles clamp on to whatever the person is
holding.
Nervous System Effects (stop breathing at
30 to 75 milli amps AC at 60 Hz, fibrillation at
75 to 100 milli amps at 60 Hz)
7
Fibrillation – a muscular twitching involving
individual muscle fibers acting without
coordination.
- very rapid irregular contractions of the muscle
fibers of the heart resulting in a lack of
synchronism between heartbeat and pulse.
- heart is “twitching” and there is no blood
flow to the body. The heart can be damaged
because it is in the path of the most common
routes electricity will take through the body:
Hand to hand
Hand to foot

8
 Burns
Although a current may not pass through
vital organs or nerve centers, internal
electrical burns can still occur. These
burns, which are a result of heat
generated by current flowing in tissues,
can be either at the skin surface or in
deeper layers (muscles, bones, etc.) or
both. Typically, tissues damaged from
this type of electrical burn heal slowly.

9
The critical path of electricity through the body is through
the chest cavity. At noted levels, current flowing from one
hand to the other, from a hand to the opposite foot, or from
the head to either foot will pass through the chest cavity
paralyzing the respiratory or heart muscles, initiating
ventricular fibrillation, and/or burning vital organs.

The effects of electric current on the

human body can vary depending on the
following:
• Source characteristics – current,
frequency and voltage of all electric
energy sources.
• Body impedance and the current’s
pathway through the body.
• How environmental conditions affect
the body’s contact resistance.
• Duration of the contact
10
Static Electricity and How It Can Do
Harm?
Why minimize static shocks?

•You may be injured by the reaction to

the shock even though the shocks are
not hazardous!

11
What you can do?
1) Never clean the glass face of your computer monitor
while the computer is on.
2) During normal operation, the glass surface of a
monitor’s CRT accumulates an electrostatic charge.
When you touch the screen with a finger, the charge in
the portion of the screen you touched discharges
through your finger with a tiny spark. Electric current
does not normally flow through glass so only part of the
screen that your finger touches is discharged. When
you clean a monitor however, the entire glass is wet
and the charge on the entire screen will discharge to
your finger or hand, causing a much more painful
shock. Clean your monitor before you turn on your
computer.
12
What you can do?
3) Never allow any electrical powered office equipment to
become wet while it is turned on.
4) Never turn on any electronic equipment when it is wet.
5) Even when a computer has been turned off for a few
minutes, it is best not to touch the monitor’s CRT while
handling or using other electrical / electronic
equipment, including the telephone. Wet or dry, you
may receive an electric shock. This shock is similar to
the shock you receive when you touch a door knob
after walking across a carpet. Although painful, this
type of shock is not hazardous. However, you may be
injured by the reaction to the shock, such as pulling
your hand rapidly away and hitting your elbow against
a wall or cabinet.
13
Controlling Electrical Fire
Stages of Fire.
•There are four (4) stages of fire:
1. Incipient stage – no visible smoke
or flame
2. Smoldering stage – there is no
smoke but no flame
3. Flame stage – actual fire exist
and heat builds up
4. Heat stage – uncontrollable
spread of superheated fire

An electrical fire originates from an energized electrical equipment, wiring, fuses

and appliances. Its extinguishment calls for a non-conductive dry powder, carbon
dioxide or vaporizing liquid. Never use water to avoid shock at fatal electrocution.
14
Electrical Fire Prevention
Practices

Keep hallways and stairways clear for quick

exits and always equip them with smoke
detectors whenever possible.
Properly placed detectors cut your chances
of dying in a home fire. Put them on every
level of your house and outside each
bedroom.
Check the test button weekly and clean it
regularly. Make sure everybody knows the
sound of alarm.
15
Electrical Fire Prevention
Practices
Blown fuses, warm outlet plates, sparks from
switches and outlets – all could be signs of an
overloaded electrical system or faulty wiring.
The Bureau of Fire Protection (BFP) identifies
“octopus connections” – where several electrical
appliances are connected to 1 outlet, resulting
in power overload and other electrical faults –
as the main cause of fires in the home. Avoid
having such connections in your house.

16
Electrical Fire Prevention
Practices

Never leave hot appliances plugged-in when

you are not around.
If you have big appliances such as a window
air conditioner, plug them into their own
heavy duty electrical circuit, not just an
outlet.
Let air circulate around your TV set and at
the back of your refrigerator to dissipate
build-up heat. Don’t place watered plants on
top of the set or ref.
17
Electrical Fire Prevention
Practices

Use extension cords only within their

designated rating.
Never let multi-outlet assemblies or
cube taps cause overloads.
Never use frayed or deteriorated
extension cords.
Never tamper with fuses to change their
current carrying capacity.
18
Causes of Electrical Accidents

Unsafe Acts
•There are 3 major causes of electrical
accidents:
1) Carelessness
2) Misuse
3) Getting in a hurry

19
There are 2 reasons for the above
causes of unsafe acts:

1. We know better but intentionally

do something unsafe.

2. We don’t know better.

20
Avoid the following unsafe acts:
•Failure to de-energize, lockout and
tag-out hazards during
maintenance, repair or inspections
of fuse box.
•Use of defective and unsafe tools.
•Use of tools or equipment too close
to energized parts.

21
Avoid the following unsafe acts:
•Not draining off stored energy in
capacitors.
•Using 3 wire cord with a 2 wire
plug.
•Remove and replace wrong fuse.
•Not verifying power is off when
making repair (drilling into a 220 V
AC line can kill).
22
Unsafe Equipment
What equipment can cause electrical
accidents?
•Loose connections
•Faulty insulation
•Improper grounding
•Defective parts, such as broken outlet
cover (unsafe accessible LIVE contacts)

23
Common Electrical
Violations Causing Dangers

The most apparent requirements in determining unsafe

equipment are related to the existence of the power supply;
the types, locations and conditions of the wiring in use; and
the existence of the number of wall outlets or ceiling fixtures
required by the PEC and their condition. In making
investigations of unsafe equipment, these considerations
will serve as useful guides.
24
1) Power Supply – where is it located, is it
grounded properly, and is it at least of
minimum capacity required to supply
current safely for lighting and the major and
minor appliances in the dwelling?
2) Panel Box Covers or Doors – these
should be accessible only from the front and
should be sealed in such a way that they
can be operated safely without the danger
of contact with live or exposed parts of the
wiring system.

25
3) Switches, Outlets and Junction Boxes –
these also must be covered to protect
against danger of electric shock.
4) Frayed or Bare Wires – these are usually
the result of long use and drying out and
cracking of the insulation, which leave the
wires exposed, or else a result of constant
friction and rough handling of the wire,
which cause it to fray or become bare.
Wiring in this condition constitutes a safety
hazard, and correction of such defects
should be ordered immediately.
26
5) Electric Cords Under Rugs or Other Floor
Coverings – putting electric cords in locations such
as these is prohibited because of the potential fire
hazard caused by continuing contact over a period of
time between these heat-bearing cords and the
flammable floor coverings. Direct the occupant to
shift the cords to a safe location, explain why, and
make sure it is done.
6) Bathroom Lighting – it should include at least 1
permanently installed ceiling or wall light fixture with
a wall switch and plate so located and maintained
that there is no danger of short circuiting from use of
other bathroom facilities or splashing of water.
Fixture or cover plates should be insulated or
grounded.

27
7) Lighting of Public Hallways, Stairways,
Landings and Foyers – a common standard
here is sufficient lighting to provide
illumination of 10 ft-candle on every part of
these areas at all times. Sufficient lighting
means that a person can clearly see his feet
on all parts of the stairways and halls. Every
public hall and stairway in a structure
containing less than 3 dwelling units may be
supplied with conveniently located light
switches controlling an adequate lighting
system that may be turned on when needed
instead of full-time lighting.

28
8) Habitable Room Lighting – the standard here may be 2 floor
convenience outlets – although floor outlets are dangerous
unless protected by proper dust and water covers – or 1
convenience outlet and 1 wall or ceiling electric light fixture.
This number constitutes an absolute and often inadequate
minimum given the contemporary widespread use of electricity
in the home. The minimum should be that number is required
to provide adequate lighting and power to accommodate
lighting and appliances normally used in each room.
9) Octopus Outlets or Wiring – this term is applied to outlets in
which plugs have been inserted and are being used to permit
more than 2 lights or portable appliances, such as TV, lamp or
radio, to be connected to the electrical system. The condition
occurs where the number of outlets is insufficient to
accommodate the normal use of the room. This practice
overloads the circuit and is a potential source of fire.

29
10)Outlet Covers – every outlet and receptacle
must be covered by a protective plate to prevent
contact of its wiring or terminals with the body,
combustible object or splashing water.
11)Excessive or Faulty Fusing – the wire’s
capacity must not be exceeded by the fuse or
circuit breaker capacity or be left unprotected by
faulty fusing or circuit breaker. Fuses and
breakers are safety devices designed to “blow”
as a means of protection against overloading of
the electrical system or 1 or more of its circuits.

30
12) Cords Run Through Walls or Doorways and Hanging
Cords or Wires – this is a makeshift-type installation and
most often is installed by an unqualified handyman or do-it-
yourself occupant.
13) Temporary Wiring – this type of installation should not be
allowed, with the exception of extension cords that go directly
from portable lights and electric fixtures to convenience
outlets.
14) Excessively Long Extension Cords – this requirement does
not apply to specially designed extension cords for operating
portable tools and trouble lights. Cities operating under
modern code standards limit the length of loose cords or
extension lines to a maximum of 8 feet. This is necessary
because those that are too long will overheat if overloaded or
if a short circuit develops and thus create a fire hazard. Even
shorter lengths are feasible in housing with new or updated
wiring system that include 1 convenience outlet every 12 feet
around the perimeter of the room.
31
 Hazardous Environment

Use special precautions when working in potentially hazardous

environments and situations. Even an accidental static discharge
can cause a fire or explosion in areas where the following are
present:
Flammable vapors, liquids and gases
Combustible dust
Corrosive atmospheres
Explosive environments 32
Safety Practices

All violations of the Philippine

Electrical Code (PEC) represent
potentially dangerous arrangements. In
order to correct these situations, the
following safety practices are
encouraged.

33
Basic Safety Practices:
•Never underestimate the
danger of 220 VAC circuits.
More people die from 220
VAC electrical shock than any
other voltage. This is mostly
due to a lack of respect.
•Watch out for electrical arcs;
they can cause bad burns.
•Do not operate equipment
beyond its rated capacity.
•Never install equipment
beyond its rated capacity.
34
 Don’t Play With Electrical Equipment:
•Don’t stick any object other than an electric plug into an outlet.
•Never fool with wires, electric meters , switches or any electrical
equipment in and around the house and yard.
•Don’t break insulators or electrical equipment
•Stay away from transformers (green boxes) and power
substations.

 Use Appliances Safely:

• Never use any electrical appliance when you’re wet, have wet
hands, or when you’re standing in water.
• Keep all electric appliances at least 10 feet away from
swimming pools.

 Caution: Remember, electricity is your friend, but use it safely.

35
Safety Checklist

Outlets
•Check for outlets that have loose-fitting plugs,
which can overheat and lead to fire.
•Replace any missing or broken wall plates.
•Make sure there are safety covers on all
unused outlets that are accessible to children.

36
Cords
•Make sure cords are in good condition – not frayed
or cracked.
•Cords should never be nailed or stapled to the wall,
baseboard or to another object.
•Do not place cords under carpets or rugs or rest
any furniture on them.
•See that the cords are not overloaded; and they
are not meant to be used permanently as
household wiring.

37
Plugs
•Make sure plugs fit your outlets.
•Never force a plug into an outlet if it doesn’t fit.
•Avoid overloading outlets with too many
appliances.

Light Bulbs
• Check the wattage of all bulbs in light fixtures to
make sure they are the correct wattage for the
size of the fixture.
• Replace bulbs that have higher wattage than
recommended.
• Make sure bulbs are secured in securely; loose
ones may overheat. 38
Circuit Breakers / Fuses
•Should be the correct size current rating for their circuit.
•If you do not know the right size, have a registered master
electrician (RME) identify and label the size to be used.
•Always replace a fuse with the same size fuse rating.

 Water and Electricity Don’t Mix

• Don’t leave plugged-in appliances where they might come into
contact with water.
• If a plugged-in appliance falls into water, never reach in to pull
it out… even if it is turned off. First turn off the power source
at the panelboard and then unplug the appliance.

 Appliance
• If an appliance repeatedly blows a fuse, trips a circuit breaker,
or if it has given you a shock, unplug it and have it repaired.
39
Outdoor Safety
•Electric powered tools and equipment
should not be use in the rain or wet
conditions.
•Always use an extension cord marked for
outdoor use and rated for the power needs
of your tools.
•Remember to unplug all portable tools
when not in use.
•Since metal ladder conducts electricity,
watch out for overhead and power lines.

40
Lightning
• During a storm, do not use
appliances (i.e. hairdryers,
toasters, radios) or
telephones (except in an
emergency).
• Do not take a bath or shower
during a storm.
• Keep batteries on hand for
flashlights in case of a power
outage.

41
Following are the safety precautions to take
with switches and receptacles:
1. All switches and outlets should be checked
periodically to make sure they are not hot to the
touch. If switches and outlets don’t work properly,
hot to the touch, produce sparks or arcs when
used, or if the switch or outlet blows a fuse or
trips a circuit breaker, this could indicate an
unsafe wiring condition. Have a licensed
electrician check the switch or outlet.
2. All outlets should have a faceplate to help
prevent exposure to “live” wiring.

42
Following are the safety precautions to take
with switches and receptacles:
3. If plugs seem to fit loosely in an outlet, the same
may be worn and could overheat; a licensed
electrician should check it.
4. Put inexpensive safety covers on receptacles to
help prevent children from inserting small objects
into it.
5. All outside receptacles, as well as in bathroom,
kitchen and basement should be weatherproof or
have waterproof covers to help protect against
shock hazards.

43
 Do’s & Don'ts for
Electrical Safety
1. Do use extension cords on a temporary
basis.
2. Do put safety covers on unused receptacle
outlets and extension cords.
3. Do unplug an appliance and call an
electrician if the receptacle face-plate feels
hot or if there is sparking, smoke, color or
odor coming from the outlet, plug or
appliance.

44
 Do’s & Don'ts for
Electrical Safety
4. Do examine appliance and extension
cords regularly for signs of wear or tear or
damage to insulation.
5. Do unplug all non-essential electrical
appliance when not in use.
6. Do use extension cords that have been
listed by a nationally recognized testing
laboratory.
7. Don’t use extension cords as permanent
substitute for inadequate house wiring.
45
 Do’s & Don'ts for
Electrical Safety
8. Don’t use extension cords that are worn or
damaged and don’t attach extension cords
to the wall with nails or staples.
9. Don’t put extension cords under rugs
where they might be walked on; don’t rest
anything on an extension cord.
10.Don’t overload cords with too many
appliances.
11.Don’t touch any appliance that has
emitted an electrical shock until the
appliance has been unplugged.
46
 Do’s & Don'ts for
Electrical Safety
12. Don’t place electrical appliances where they might
come in contact with water. Never reach into water for
plugged-in appliance… turn off power first, then unplug
it.
13.Don’t place an appliance cord where it might touch a
hot surface.
14.Don’t leave any wiring exposed in outlets and switches.
Use the correct size faceplate.
15.Don’t ignore switches or outlets that don’t work. Obtain
the help of a licensed electrician.
16.Don’t let cords hang over countertops where children
can pull down an appliance.
47
Hazards and Safety Tips
for Electricians
The Philippine Electrical Code (PEC) sets the
minimum standards for electrical work in general
and specific instances. Any person employed in the
electrical field should obtain a copy of the PEC and
know how to use it. This is commonly referred to as
the electrician’s handbook.

48
Basic Safety Precautions
Never bypass a fuse.
Be sure all current carrying electric lines are well insulated.
Always check a circuit for voltage before servicing.
Know where all emergency shutdown switches are located.
Work on live circuits only when absolutely necessary.
Watch for burned wires on electrical devices.
Never touch a conductor without first testing.
Look for loose conductors in electrical systems.
Do not make any adjustment or repairs to any electrical
equipment until all power has been disconnected or the
circuit breaker has been turned off.

49
Caution: Adjustments or repairs should be done only
by licensed electrical engineers or electricians.
•All electrical equipment and tools should be properly
grounded to pre4vent any injury to the operator.
•Do not operate electrical parts with wet gloves or wet
clothing.

Caution: To prevent harmful body shocks, keep

hands, feet and clothing dry. Use a dry board or rubber
mat when water, moisture or perspiration cannot be
avoided.
•Never work alone when working with more than 50
volts.
50
 Safety Practices Around Live Circuits.

•Use a reliable circuit tester or

voltmeter to identify live
circuits.
•Stand on dry surface.
•Use only one hand of
possible.
•Never keep tools lying around
live conductors.
•Wear suitable insulated hand
covering.
•Return all tools to pouch when
through with them.
51
Proper Grounding.
•Properly grounded electrical equipment provides a
pathway to ground for stray current that may
otherwise go through the operator’s body.
•Loose wires that touch the case of housing in
electrical equipment can cause an electrical shock
to anyone who touches the equipment if it has not
been properly grounded.
Caution: A faulty current to the housing will travel
directly to ground. A working touching the
equipment is not likely to suffer a serious shock
because the ground is a better current path than
the human body.

52
Importance of Third Wire
Always check for grounding or third wire
before using electrical equipment to
avoid electrical shock. The importance
of third wire as follows:
•Installed for personal protection.
•Provides alternate path for current in
case of a short.
•Can save your life.

53
 Ground Fault Circuit Interrupters (GFCI)
When the ground fault circuit interrupter works properly, the
power is cut off so fast that the shock can be reduced to a few
microseconds.
GFCI’s are:
• Personal safety devices.
• Required on 15 and 20 ampere receptacle outlets used for
temporary power supply on construction sites.
• Stops current before severe personal injury occurs.

54
Facts About Electric Shock
Body Resistance
Human body resistance varies from
about 500,000 ohms when dry to about
300 ohm when wet. Because of this,
voltage as low as 30 V can cause
enough current to be fatal. Any circuit
with a potential of at least 30 V must be
considered dangerous.

55
Selecting an Electrical
Contractor

Right contractor for the

job
•If you’re trying to get your
home/school/office/workplace’s
electrical system inspected or
upgraded w/out getting
overcharged and ensuring
electrical safe installation, you
may be interested in these tips
on how to select a qualified
electrical contractor.

56
1) Check the phone book, usually under “Electric”
or “Contractor”, or you may call the PCAB. Better
yet, call the SPECS.

57
2. Ask where the contractor is located. There are some out-
of-area contractors that use the phonebook to solicit
business. Ask for PRC licenses (PEE/REE/RME) and
PCAB licenses (Specially Electrical Contractor). Ask for
company profile. Phone the company to make sure the
licenses are current.
3. Have more than one electrical contractor give you an
estimate. Beware of non-licensed electrical practitioners.
Most reputable companies require PRC and PCAB
licenses before they can practice.
4. Ask for local references. You can alos call the IIEE
Chapter in your area. Determine if the contractor is a
member of a national or regional electrical association.
Membership does not guarantee quality, but ongoing
educational programs keep members up to date on the
latest technological developments in the electrical
industry.
12/9/2015 58
Electrical Accidents

12/9/2015 59
Electrical Accidents

12/9/2015 60
Electrical Violations

12/9/2015 61
Electrical Violations

12/9/2015 62
Electrical Violations

12/9/2015 63
END OF PRESENTATION

12/9/2015 64