Milling Machine

Assignment no: Roll number:
Name of Assignment: Milling Machine
Q1. Explain column and knee type milling machine with neat sketch.
1. For general shop-work the most
commonly used is the column and knee
type where the table is mounted on the
knee-casting which in turn is mounted on
the vertical slides of the main column.
2. The knee is vertically adjustable on the
column so that the table can be moved up
and down to accommodate work of
various heights.
3. The column and knee type milling
machines are classified according to the
various methods of supplying power to
the table, different movements of the
table and different axis of rotation of the
main spindle.
4. The column and knee type is classified into the following types: Head Milling Machine
a. Plain Milling Machine
b. Universal Milling Machine
c. Omniversal Milling Machine
d. Vertical Milling Machine
Q2. Compare plain milling and universal milling machine.

Plain Milling Machine Universal Milling Machine
1. The plain milling machine is provided with 1. The universal milling machine has a fourth
three table movements: longitudinal, cross movement of the table in addition to the
and vertical. longitudinal, cross and vertical. The table can
be swiveled horizontally and can be fed at an
angle to the milling machine.
2. Helical milling works cannot be done as the 2. The table can be swiveled and helical
table cannot be swiveled. milling and spiral milling can be performed.
3. As there are no auxiliaries in plain milling 3. The universal milling machine is provided
machine. Hence, operation like gear cutting, with auxiliaries like dividing head equipment,
slotting and vertical milling cannot be vertical milling attachment, rotary table, etc.
performed. These extras and the special design of the
machine itself make it possible to produce
spur, spiral bevel gears, twist drills, reamers,
milling cutters, etc.
4. The plain milling machine is rigid and 4. The universal milling machine is less rigid
heavier. and lighter as compared to plain milling
machine.
5. The plain milling machine is adapted for 5. The universal milling machine is intended
manufacturing operations. for tool room work and for special machining
operations.
Q3. Explain various types of work holding devices on milling.

It is necessary that the work should be properly and securely held on the milling machine table
for effective machining operations. The following are the usual methods of holding work on the
table.
A. T-bolts and clamps:
1. Bulky workpieces of irregular shapes are clamped directly on the milling machine table by
using T-bolts and clamps.
2. Different designs of clamps are used for different patterns of work.
B. Angle plates:
1. When work surfaces are to be milled at right angles to another face, angle plates are used for
supporting the work.
2. The angle plate is bolted on the table and the workpiece is supported on its face by bolts and
clamps.
3. A tilting type angle plate in which one face can be adjusted relative to the another for milling
at a required angle is also sometimes used. A tilting type angle plate is shown in the figure.
C. V-blocks:
1. The V-blocks are used for holding shafts on milling machine table in which keyways, slots and
flats are to be milled.
2. The blocks are clamped on the machine table by straps and bolts.
3. V-blocks are provided with a tongue at its base which fits into the T-slot of the table and
prevents the block from any sideways movements.
D. Vises:
1. Vises are the most common appliances for holding work on milling machine table due to its
quick loading and unloading arrangement.
2. There are mainly three types of vises commonly used in milling machines.
3. They are plain, swivel vise, and tool makers’ universal vise.
E. Special fixtures:
1. The fixtures are special devices designed to hold work for specific operations more efficiently
than standard work holding devices.
2. Fixtures are especially useful when large numbers of identical parts are being produced.
3. By using fixtures loading, locating, clamping and unloading time is greatly minimized.
Q4. List various tool holding devices on milling machine.
There are several methods of supporting and rotating milling cutter with the machine spindle
depending on the different designs of the cutters. The following are the different devices for
holding and rotating cutters.
1. Arbors: The cutters have a bore at the center arc mounted and keyed on a short shaft called
arbor which is connected with the milling machine spindle by a draw bolt and driving keys.
2. Collets: A milling machine collet is a form of sleeve bushing for reducing the size of the taper
hole at the nose of the milling machine spindle so that an arbor or a milling cutter having a
smaller shank than the spindle taper can be fitted into it.
3. Adapter: An adapter is a form of collet used on milling machine having standardized spindle
end. Cutters having shanks are usually mounted on adapters. An adapter can be connected with
the spindle by a draw bolt or it may be directly bolted to it.
4. Spring collets: Straight shank cutters are usually held on a special adapter called "spring
collet" or "spring chuck". The nose end of the adapter is tapered and threaded for a small
distance and also split by three equally spaced slots. The cutter shank is introduced in the
cylindrical hole provided at the end of the adapter and then the nut is tightened. This causes
the split jaws of the adapter to spring inside, and grip the shank firmly.
5. Bolted cutters: The face milling cutters of larger diameter having no shank are bolted directly
on the nose of the spindle. For this purpose four bolt holes are provided on the body of the
spindle. This arrangement of holding cutter ensures utmost rigidity.
6. Screwed on cutters: The small cutters having threaded holes at the center are screwed on
the threaded nose an arbor which is mounted on the spindle in the usual manner. The cutter
threads may be right hand or left hand depending on the direction of rotation of the cutter so
that the cutter may not come off the arbor during the cut.
Q5. Explain plain milling cutter nomenclature with diagram.

The plain milling cutter nomenclature has been described below:
1. Body of cutter: The part of the cutter left after exclusion of the teeth and the portion to
which the teeth are attached.
2. Cutting edge: The edge formed by the intersection of the face and the circular land or the
surface left by the provision of primary clearance.
3. Face: The portion of the gash adjacent to the cutting edge on which the chip impinges as it is
cut from the work.
4. Fillet: The curved surface at the bottom of gash which joins the face of one tooth to the back
of the tooth immediately ahead.
5. Gash: The chip space between the back of one tooth and the face of the next tooth.
6. Land: The part of the back of tooth adjacent
to the cutting edge which is relieved to avoid
interference between the surface being
machine and the cutter.
7. Lead: The axial advance of the helix of the
cutting edge in one complete revolution of the
cutter.
8. Outside diameter: The diameter of the circle
passing through the peripheral cutting edge.
9. Root diameter: The diameter of the circle
passing through the bottom of the fillet.
10. Relief angle: The angle in a plane
perpendicular to the axis, which is the angle
between the land of a tooth and the tangent to the outside diameter of cutter at the cutting
edge of that tooth.
11. Primary clearance angle: The angle formed by the back of the tooth with a line drawn
tangent to the periphery of the cutter at the cutting edge.
12. Secondary clearance angle: The angle formed by the secondary clearance surface of the
tooth with a line drawn tangent to the periphery of the cutter at the cutting edge.
13. Rake angle (Radial): The angle measured in the diametric plane between the face of the
tooth and a radial line passing through the tooth of cutting edge. The rake angles may be
positive, negative or zero.
14. Lip angle: The included angle between the land and the face of the tooth or alternatively
the angle between the tangent to the back at the cutting edge and the face of the tooth.
15. Helix angle: The cutting edge angle which a helical cutting edge makes with a plane
containing the axis of a cylindrical cutter.
Q6. Differentiate between conventional and climb milling.
Conventional Milling Climb Milling

1. Conventional milling is also known as 1. Conventional milling is also known as
upmilling. upmilling.
2. It is the process of removing metal by a 2. It is the process of removing metal by a
cutter which is rotated against the direction of cutter which is rotated in the same direction
travel of the workpiece. of travel of the workpiece.
3. The thickness of the chip in upmilling is 3. The thickness of the chip in upmilling is
minimum at the beginning of the cut and it maximum at the beginning of the cut and it
reaches to the maximum when the cut reaches to the minimum when the cut
terminates. terminates.
4. As the chip thickness is not uniform, the 4. The cutter tooth starts removing metal
cutting in upmilling increases from zero to the immediately on reaching the work-surface,
maximum value per tooth movement of the without sliding, as it can apply a sufficient bite
cutter. on the work.
5. As the cutter progresses, the chip 5. The chips are disposed off easily and do not
accumulate at the cutting zone, and may be interfere with the cutting.
carried over with the cutter spoiling the work
surface.
6. The cutting force is directed upwards and 6. The cutting force is such that it tends to seat
this tends to lift the work from the fixtures. the work firmly in the work holding devices.
7. In upmilling, due to the typical nature of the 7. The coolants can be poured directly at the
cut, difficulty is experienced in pouring coolant cutting zone where the cutting force is
just on the cutting edge from where the chip maximum.
begins.
Q7. Explain various milling operations with diagram.

The following are the different operations performed in a milling machine:
A. Plain milling:
a. The plain milling is the operation of production of a plain, flat, horizontal
surface parallel to the axis of rotation of a plain milling cutter.
b. The operation is also called slab milling. To perform the operation, the
work and the cutter are secured properly on the machine.
c. The depth of cut is adjusted by rotating the vertical feed screw of the table
and the machine is started after selecting proper speed and feed.
B. Face milling:
a. The face milling operation is performed by a face milling cutter rotated
about an axis perpendicular to the work surface.
b. The operation is carried in a plain milling machine, and the cutter is
mounted on a stub arbor to produce a flat surface.
c. The depth of cut is adjusted by rotating the cross feed screw of the table.
C. Side milling:
a. The side milling is the operation of production of vertical surface
on the side of a flat workpiece by using side milling cutter.
b. The depth of cut is adjusted by rotating the vertical feed screw
of the table.
D. Straddle milling:
a. The straddle is the operation of production of flat vertical
surfaces on both sides of a workpiece by using two side milling
cutters mounted on the same arbor.
b. The distance between the two cutters is correctly adjusted
by using suitable spacing collars.
c. The straddle milling is very commonly used to produce
square or hexagonal surfaces.
E. Angular milling:
a. The angular milling is the operation of production of an angular surface
on a workpiece other than at right angles to axis of the milling machine
spindle.
b. The angular groove may be single or double angle and may be of varying
included angle according to the type and shape of the angular cutter used.
c. One simple example of angular milling is the production of V-blocks.
F. Gang milling:
a. The gang milling is the operation of machining several surfaces of a
workpiece simultaneously by feeding the table against a number of cutters
having same or different diameters mounted on the arbor of the machine.
b. The method saves much of machining time and is widely used in
repetitive work. c. The cutting speed of a gang of cutters is calculated from
the cutter of the largest diameter.
G. Form milling:
a. The form milling is the operation of production of irregular contours by using form cutter.
The irregular contour may be convex, concave, or of any other shape.
b. After machining, the formed surface is checked by a template gauge. The cutting speed for
form milling is 20% to 30% less than that of the plain milling.
1 – Formed cutter and 2 - Work
H. Profile milling:
a. The profile milling is the operation of reproduction of an outline of a template or complex
shape of a master die on a workpiece.
b. Different cutters may be used for profile milling. An end mill is one of the most widely used
milling cutters in profile milling work.
I. End milling:
a. The end milling is the operation of production of a flat surface which may be vertical,
horizontal or at an angle in reference to the table surface.
b. The cutter used is an end mill. The end milling cutters are also used for production of slots,
grooves or keyways.
c. A vertical milling machine is most suitable for end milling operation.
1 – End mill
J. Saw milling:
a. The saw milling is the operation of production of a narrow slots or grooves on a workpiece by
using a saw milling cutter.
b. The saw milling can also be performed for complete parting-off operation.
c. The cutter and the workpiece are set in a manner so that the cutter is directly placed over
one of the T-slots of the table.
1 – Saw mill and 2 – Work

Milling Machine

Uploaded by

Copyright:

Available Formats

Milling Machine

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Milling Machine

Uploaded by

Copyright:

Available Formats

What are the main types of milling machines and their differences?

What are the common work holding devices used in milling?

Assignment no: Roll number:

Name of Assignment: Milling Machine

Q2. Compare plain milling and universal milling machine.

Q3. Explain various types of work holding devices on milling.

Q5. Explain plain milling cutter nomenclature with diagram.

Q6. Differentiate between conventional and climb milling.

Conventional Milling Climb Milling

Q7. Explain various milling operations with diagram.

1 – Formed cutter and 2 - Work

1 – Saw mill and 2 – Work

You might also like