Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd
Upload
65 views

Drill Stem Testing, DST

Drill stem testing provides a method to temporarily complete a well and determine the productivity of a specific zone. It involves running a bottom assembly with a packer and valve into the hole. The valve is closed while running in and opened once the packer isolates the target formation. Pressure recordings during flowing and shut-in periods provide data on reservoir characteristics like pressure, permeability, and fluid contacts. Analysis of the pressure buildup curves allows estimating parameters like reservoir pressure. Multiple flowing and shut-in periods improve data quality and enable more sophisticated well test analysis.

Uploaded by

Uthman Mohammed
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
65 views

Drill Stem Testing, DST

Drill stem testing provides a method to temporarily complete a well and determine the productivity of a specific zone. It involves running a bottom assembly with a packer and valve into the hole. The valve is closed while running in and opened once the packer isolates the target formation. Pressure recordings during flowing and shut-in periods provide data on reservoir characteristics like pressure, permeability, and fluid contacts. Analysis of the pressure buildup curves allows estimating parameters like reservoir pressure. Multiple flowing and shut-in periods improve data quality and enable more sophisticated well test analysis.

Uploaded by

Uthman Mohammed
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Drill Stem Testing, DST

Drill Stem testing provides a method of temporarily completing a well to


determine the productivity characteristics of a specific zone. As originally conceived, a
Drill Stem Test provided primarily an indication of formation content. Also the pressure
versus time chat was available.
Reservoir characteristics that may be estimated from DST analysis include;
- Average effective permeability
- Reservoir pressure
- Identify reservoir fluids
- Well-bore damage
- Barriers, fluid contacts
- Radius of investigation
- Depletion

DST Tools
Type of DST tolls depends on the testing well, cased or open hole.
1- Surface pressure control equipments
It is a collection of valves, flanges and nipples set on well head, used to control on
flow rate and internal closed or flowing pressure.
2- Drill pipe
Drill pipe used as connection between surface equipment and test equipment.
3- Reverse circulation sub
This sub valve used to circulation the drill mud (reveres circulation, from annulus
to inside drill pipe), for killing the well and control on well after the test was
finish or in emergency cases, and the valve used to empty the drill test stem from
fluids when pull out of hole. During the tools run in hole this valve remain closed
and still closed until the test was finished, after that its open to control on well.
4- Drill collar
Used to set the packer and open or close tester valve by its weight.
5- Reverser circulation ports
Also, used to reveres circulation of drill mud after the test was complete.
6- Closed in pressure valve
The valve used to close the drill stem after the test was finish.
7- Flow choke
The flow choke with a specific diameter (5/8 inch) used to fluid flow through it
and to calculations purpose.
8- Tester valve
This valve used to control on fluid movement (flow or close), the valve is closed
by put the drill stem under tension, or open it by slack off the stem. (Some times
the valve called multi flow evaluator MFE).
9- Upper pressure recorder
This instrument includes pressure record that consists from spiral tube that moves
according to amount of supply pressure, the tube shifting is transit through a small
needle to a black chart (previously, set on it lines with a specific pressure). All
operations that occur during the test will recorded on the black chart as pressure
versus time profile.
10- Hydraulic jar
It is a motional nipple, used to release the test stem in stuck case.
11- Safety joint
This joint is useful in case of stem stuck. When stem does not release, could back
the part of stem by open it from the safety joint.
12- Packer
It is the important part of the test stem; consist from steel and rubber part. After
set the packer by supply a certain weight, the rubber part will isolate the upper of
well from the formation (remove the hydrostatic pressure from the formation).
After the test on formation was completed, then the packer return to its normal
situation by removes the supplied weight, and the formation will be under control
by the hydrostatic mud column pressure.
13- Perforated pipe
Through this pipe the oil and gas enter inside the test stem.
14- Temperature recorder
This recorder used to record tested formation temperature.
15- Bottom pressure recorder
Its second pressure instrument also used to record flowing and closed bottom-hole
pressure.
16- Tail pipe anchor
Tail pipe anchor is the last part of test stem used for support purpose.

Basics of DST operations


Simply a drill stem test is made by running in the hole on drill pipe a bottom
assembly consisting of a packer and a surface operated valve. The DST valve (tester
valve) is closed while the drill string is run, thus pressure inside the drill pipe is very low
compared to hydrostatic mud column pressure (some times fill inside drill pipe with
amount of water, called water cushion to reduce the impact of high pressure). Once on
bottom, the packer is set to isolate the desired formation zone from mud column, and the
control valve is opened to allow formation fluids to enter the drill pipe.
After suitable period, the valve is closed, and a pressure build-up occurs below
the valve as formation fluids repressure the area around the well-bore. After a suitable
build-up time, the control valve usually is opened again, and the flowing and shut-in
periods repeated, (several times if desired), to obtain additional data and verification.
Figure (1) shows schematically a simple single-flow period operational sequence.
Pressure versus Time Plot
The entire sequence of events is recorded on a pressure vs time plot shown
schematically in figure (2). As the tools are run in the hole, the pressure records the
increase in hydrostatic mud column pressure. The pressure at point A is termed the initial
hydrostatic mud pressure.
Initial Flowing and Shut-in Periods- one objective of the DST is to determine the
static or shut—in reservoir pressure of the zone. To measure true static reservoir pressure,
any over-pressured condition near the well-bore, due to drilling fluid filtration or fluid
compression in setting the DST packer, must first be relived by a short flowing period.
The control valve is then closed and pressure builds-up toward static reservoir
pressure. Depending on the length of the flowing period, the length of the shut-in period,
and certain reservoir parameters, the pressure may or may not level out at the true static
reservoir pressure. Thus point B, initial shut-in pressure, may be somewhat less than true
static reservoir pressure.
Second Flowing and Shut-in Periods- the objective of the second flowing and
shut-in periods is to permit the calculation of reservoir parameters, as well as to
determine fluid production. As the control valve is opened, pressure falls to point C
(initial flowing pressure). As fluids move into the drill pipe above the recorder, pressure
increases, reflecting the increase in hydrostatic head of liquid and in back pressure, due to
flow restrictions in the tools.
After a suitable period of time, depending on test objectives, hole conditions and
the cost of rig time, the tool is shut-in. The pressure at the moment of shut-in, point D, is
termed the final flowing pressure. Recorded pressure then rises toward point E, the final
shut-in pressure. Usually the final shut-in pressure is significantly less than the static
reservoir pressure, again due to limitation of time relative to reservoir parameters.
This second pressure build-up portion of the DST, following a reasonably long
flowing period, usually provides data for transient pressure analysis. Some-times DST`s
are designed having two reasonably long flowing period and subsequent shut-in periods,
to provide verification of calculations, and to permit more sophisticated well testing
techniques. Figure (3) is typical of actual multiple-flow-period charts with key points
described therein.

You might also like