TDS - Glenium Ace 30 PDF

®
GLENIUM ACE 30
Admixture Controlled Energy Essential component of Zero Energy system. A chloride free, new
generation of polycarboxylic ether superplasticizer. In synergy with Smart Dynamic Concrete
(SDC), it optimises the production of precast concrete structural elements. Suitable during the
summer. Meets the requirements of EN 934 – 2 and ASTM C494 type A and F.
Description and field of application • Eliminate the heat curing

GLENIUM® ACE 30 is an innovative second • Eliminate the energy required for placing and
generation of polycarboxylic ether polymers compaction and curing (ZERO ENERGY)
superplasticizer. The particular molecular • Increase productivity
configuration of GLENIUM® ACE 30 accelerates • Improve surface appearance
the cement hydration. Rapid adsorption of the • Produce durable precast concrete elements
molecule onto the cement particles, combined as per EN 206-1
with an efficient dispersion effect, exposes • As compared to the traditional
increased surface of the cement grains to react superplasticizers, the engineering properties
with water. As a result of this effect, it is possible such as early and ultimate compressive and
to obtain earlier development of the heat of flexural strengths, bond to steel, modulus of
hydration, rapid development of the hydration elasticity, shrinkage, creep, and
products and, as a consequence, higher impermeability are improved.
strengths at very early age.
Packing and storage
GLENIUM® ACE 30 is recommended for use at GLENIUM® ACE 30 is available in 208 litre drums
ambient temperature above 15°C. or in bulk.
GLENIUM® ACE 30 may be used in combination GLENIUM® ACE 30 must be stored in a place
with RheoMATRIX for producing Smart Dynamic where the temperature does not drop below 5°C.
Concrete (SDC). The technology produces In case the product freezes, bring the temperature
advanced self compacting concrete, without the of the product to 30°C and remix.
aid of vibration. For economic, ecological and
ergonomic ready-mix / precast concrete Standards
production. EN 934-2 Tables 3.1 and 3.2
Benefits
GLENIUM® ACE 30 offers the following benefits
for the precast concrete industry to:
• Produce Smart Dynamic Concrete.

• Optimize the curing cycles by reducing curing
time or curing temperature
GLENIUM® ACE 30
Compatibility
GLENIUM ACE 30 is compatible and Note
recommended for use with: Field service, where provided, does not constitute
• RheoMATRIX to modify the viscosity of SCC. supervisory responsibility. For additional
• MICRO-AIR, air entraining admixture, to information contact your local BASF
representative.
improve freeze-thaw resistance (exposure
class XF1 to XF4, EN 206-1)
BASF reserves the right to have the true cause of
• RHEOFINISH, demoulding agent for easy
any difficulty determined by accepted test
formwork removal and improved finish.
methods.
• MASTERKURE, curing compound for highly
efficient water retention and friendly use. Quality and care
All products originating from BASF’s Dubai, UAE
GLENIUM ACE 30 is not compatible with all facility are manufactured under a management
admixtures of RHEOBUILD series. system independently certified to conform to the
requirements of the quality, environmental and
Dosage rate occupational health & safety standards ISO 9001,
The normally recommended dosage rate is 0.5 to ISO 14001 and OHSAS 18001.
1.0 liters per 100 kg of the binder and any material 05/2002 BASF_CC-UAE revised 06/2009
(fines or fillers) passing the 0.1 mm sieve used for
producing Smart Dynamic Concrete.
Other dosages may be used in special cases

according to specific job site conditions. In this
case please consult our Technical Services
Department.
Directions for use

GLENIUM® ACE 30 is a liquid admixture to be
added to the concrete during the mixing process.
The best results are obtained when the admixture
is added after all the other components are
already in the mixer and after the addition of at
least 80% of the total water. The water content is
adjusted to obtain the desired consistence or
workability.
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is given or implied with
any recommendations made by us, our representatives or distributors, as the conditions of use and the competence of any labour involved in the
application are beyond our control.
As all BASF technical datasheets are updated on a regular basis it is the user's responsibility to obtain the most recent issue.
BASF Construction Chemicals UAE LLC

P.O. Box 37127, Dubai, UAE
Tel: +971 4 8090800 Fax: +971 4 8851002
Certificate No. Certificate No. Certificate No.
www.basf-cc.ae e-mail: marketingcc.mideast@basf.com 963680 945787 772556

TDS - Glenium Ace 30 PDF

Uploaded by

Copyright:

Available Formats

TDS - Glenium Ace 30 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

TDS - Glenium Ace 30 PDF

Uploaded by

Copyright:

Available Formats

®

Description and field of application • Eliminate the heat curing

• Produce Smart Dynamic Concrete.

Other dosages may be used in special cases

Directions for use

BASF Construction Chemicals UAE LLC

You might also like