27 Service Manual - Packard Bell - Dot Mr-U MR

www.SoporteTecnicoBsAs.com.
ar
Repuestos para tus equipos.

Al mejor precio.
Envios a Todo el Pais

Packard Bell dot mr/u
and
Packard Bell dot mu
Service Guide
Service guide files and updates are available

on the ACER/CSD web; for more information,
please refer to http://csd.acer.com.tw
PRINTED IN TAIWAN
VI
System Specifications 1
Features 1
System Block Diagram 4
Your Notebook Tour 5
LCD View 5
Top View 5
Closed Front View 6
Left View 7
Right View 7
Base View 8
Rear View 8
Indicators 9
TouchPad Basics 10
Using the Keyboard 11
Lock Keys and embedded numeric keypad 11
Windows Keys 12
Hot Keys 13
Special Keys 14
Hardware Specifications and Configurations 15
System Utilities 25
BIOS Setup Utility 25
Navigating the BIOS Utility 25
Information 26
Main 27
Security 28
Boot 31
Exit 32
BIOS Flash Utility 33
DOS Flash Utility 34
WinFlash Utility 35
Remove HDD/BIOS Password Utilities 36
Removing BIOS Passwords: 37
Miscellaneous Utilities 38
Machine Disassembly and Replacement 41
Disassembly Requirements 41
Related Information 41
Replacement Requirements 41
Pre-disassembly Instructions 42
Disassembly Process 43
External Module Disassembly Process 44
External Modules Disassembly Flowchart 44
Removing the Battery Pack 45
Removing the Dummy Card 46
Removing the Hard Disk Drive Module 47
Removing the DIMM Module 49
Removing the WLAN Module 51
Main Unit Disassembly Process 53
Main Unit Disassembly Flowchart 53
Removing the Keyboard 55
Removing the Upper Cover 57
Removing the Button Board 59
Removing the LCD Module 62
VII
Removing the LED Board 64
Removing the Bluetooth Module 66
Removing the I/O Board 67
Removing the Mainboard 69
Removing the CRT Board 71
Removing the Thermal Module 72
Removing the RTC Battery 73
Removing the Speaker Modules 74
LCD Module Disassembly Process 75
LCD Module Disassembly Flowchart 75
Removing the LCD Bezel 76
Removing the Camera Board 77
Removing the LCD Panel 78
Removing the LCD Brackets 80
Removing the FPC Cable 81
Removing the Antennas 82
LCD Reassembly Procedure 84
Replacing the Antennas 84
Replacing the FPC Cable 86
Replacing the LCD Brackets 87
Replacing the LCD Panel 88
Replacing the Camera Board 90
Replacing the LCD Bezel 91
Main Unit Reassembly Process 93
Replacing the Speaker Modules 93
Replacing the RTC Battery 94
Replacing the Thermal Module 95
Replacing the CRT Board 96
Replacing the Main Board 97
Replacing the I/O Card 99
Replacing the Bluetooth Module 101
Replacing the LED Board 102
Replacing the LCD Module 104
Replacing the Button Board 107
Replacing the Upper Cover 110
Replacing the Keyboard 112
Replacing the Wireless LAN Module 113
Replacing the DIMM Module 115
Replacing the Hard Disk Drive 116
Replacing the Battery 118
Replace the Dummy Card 119
Troubleshooting 121
Common Problems 121
Power On Issue 122
No Display Issue 123
Random Loss of BIOS Settings 124
LCD Failure 125
Built-In Keyboard Failure 126
TouchPad Failure 127
Internal Speaker Failure 128
Internal Microphone Failure 129
HDD Not Operating Correctly 130
USB Failure (Right up/down side) 131
Other Failures 131
VIII
Intermittent Problems 132
Undetermined Problems 132
POST Code Reference Tables 133
Jumper and Connector Locations 137
Mainboard Top View 137
Mainboard Bottom View 138
Clearing Password Check and BIOS Recovery 139
Mainboard CMOS Discharge 139
BIOS Recovery by Crisis Disk 140
FRU (Field Replaceable Unit) List 141
Packard Bell dot Exploded Diagrams 141
Main Assembly 142
LCD Assembly 144
Screw List 150
Model Definition and Configuration 151
Test Compatible Components 153
Online Support Information 157
Index 159
IX
X
Chapter 1
System Specifications
Features
Below is a brief summary of the computer’s many features:
Operating System
• Genuine Windows Vista ®
Platform
• Intel Centrino® processor technology, featuring:
• Intel® Core™2 Solo processor SU3500 (3 MB L2cache, 1.40 GHz, 800 MHz FSB, 5.5 W),
supporting Intel® 64 architecture
• Mobile Intel® GS45 Express Chipset
• Intel® Wireless WiFi Link 5100 (dual-band quad-mode 802.11a/b/g/Draft-N) Wi-Fi
CERTIFIED™ network connection, featuring MIMO technology
• Intel® Wireless WiFi Link 5100 (dual-band 802.11a/b/g) Wi-Fi CERTIFIED™ network
connection, featuring MIMO technology (availableonly in Russia, Pakistan, Ukraine)
• Intel® Celeron® mobile processor 723 (1 MB L2 cache, 1.20GHz, 800 MHz FSB,10 W),
supporting Intel® 64 architecture
• Mobile Intel® GS45 Express Chipset
• 802.11b/g/Draft-N Wi-Fi CERTIFIED™ network connection2
System Memory
• Dual-channel DDR2 SDRAM support:
• Up to 2 GB of DDR2 667 MHz memory,
• upgradeable to 4 GB using two soDIMM modules (for 32-bit OS)
Display and graphics

• 11.6" HD 1366 x 768 (WXGA) pixel resolution, high-brightness (200-nit) Packard Bell Diamond
View TFT LCD 16:9 aspect ratio
• Mobile Intel® GS45 Express Chipset with integrated 3D graphics, featuring Intel® Graphics Media
Accelerator 4500MHD (Intel® GMA 4500MHD) with up to 1759 MB of Intel® Dynamic Video
Memory Technology 5.0 (64 MB of dedicated video memory, up to 1695 MB of shared system
memory), supporting Microsoft® DirectX® 10
Storage subsystem
• 2.5” 9.5mm 160 GB or larger hard disk drive
• Multi-in-1 card reader
Chapter 1 1
Audio subsystem
• High-definition audio support
• Two built-in stereo speakers
• MS-Sound compatible
• Built-in digital microphone
• S/PDIF (Sony/Philips Digital Interface) support for digital speakers
Communication
• Integrated Acer Crystal Eye webcam, supporting 0.3-megapixel resolution
• WLAN: Acer InviLink™ 802.11b/g Wi-Fi CERTIFIED® network connection, supporting Acer
SignalUp™ wireless technology
• LAN: 10/100 Mbps Fast Ethernet
• WPAN: Bluetooth® 2.0 or 2.1+EDR
• WWAN: UMTS/HSPA at 850/1900/2100MHz and quad-band GSM/GPRS/EDGE(850/900/1800/
1900 MHz)(for 3G models)
Privacy control
• Kensington lock slot
• BIOS user, supervisor, HDD passwords
Dimensions and Weight)

• 285 (W) x 204 (D) x 22.1/30 (H) mm (11.22 x 8.03 x 0.87/1.18 inches)
• 1.35 kg (2.97 lbs.) with 6-cell battery pack
Power subsystem
• 47.52 W 4400 mAh 6-cell Li-ion battery pack (for Intel® Celeron® 723 only):
• • 6-hour battery life9
• 62.16 W 5600 mAh 6-cell Li-ion battery pack (for Intel® Core™2 Solo SU3500 only):
• • 8-hour battery life9
• Energy Star® 5.0
• 30W adaptor with power cord
Input devices
• 84-/85-/88-key full-size keyboard, with inverted "T" cursor layout
• Touchpad pointing device with two buttons
I/O interface
• Multi-in-1 card reader
• Three USB 2.0 ports
• HDMI™ port with HDCP support
• External display (VGA) port
• Headphone/speaker/line-out jack with S/PDIF support
2 Chapter 1
• Microphone-in jack
• Ethernet (RJ-45) port
• DC-in jack for AC adapter
Environment
• Temperature:
• Operating: 5°C to 35°C
• Non-operating: -20°C to 65°C
• Humdity (non-condensing):
• Operating: 20% to 80%
• Non-operating: 20% to 80%
NOTE: The specifications listed above are for reference only. The exact configuration of the PC depends on
the model purchased.
Chapter 1 3
System Block Diagram
PC B ST A C K UP
8L H DI POW E R
XTAL
C L OC K SY ST E M 5V /3V
L A Y E R 1 : T OP
Y2 C K 505 (Q F N-64) R T 8206B P24
L A Y E R 2 : G ND 14.318MHZ
PG 2
L A Y E R 3 : I N1 C PU C or e
L AY E R 4 : V CC I SL 6261A P25
F AN & T HE R M AL
L A Y E R 5 : I N2
P3 DDR Power
L A Y E R 6 : I N3
C PU R T 8207A P26
L A Y E R 7 : G ND
L A Y E R 8 : B OT Penr yn SFF UL V DC /SC V C C P 1.05V
R T 8202A P27
M icr o-F C B G A 956/10W P3,4
1.5V
800/1066 M H z F SB G 9334/A O4466 P28
L V DS L E D Panel 1.5V _S5
DDR 2-SODI M M cahnge A NOR T H B R I DG E C onnector P22 R T 9025 P28
P15 VGA CR T Dischar ge
667/800M H Z DDR I I
C antiga SFF G S45 C onnector P21 P28
DDR 2-SODI M M cahnge B
T M DS H DM I L evel Shifter H DM I GFX
P16 P22 C onnector P22 I SL 6263A P29
PG 5,6,7,8,9,10
DM I x 4
PC I E 4 M I NI C A R D 1
2.5H DD SA T A 0 SOUTH BRIDGE C onnector P19
P20
PC I E PC I E 5 M I NI C A R D 2 SI M C A R D
On B oar d USB 0 Por t 6
C onnector P19 C onnector P19
P20
PC I E 1 C onnector GL AN XTAL
M I NI C A R D 1 Por t 7 Y2
I C H 9-M SFF P21 A ther os A R 8131L 25MHZ
P19
M I NI C A R D 2 Por t 2 I H DA L ine Out/M I C C onnector
P21
P19 C ODE C
Speaker Speaker C onnector
CCD Por t 4 USB R ealtek A L C 269X
P21
P22
Digital M I C L E D Panel
B ule T ooth Por t 5 PG 11,12,13,14 XTAL P17 C onnector P22
P21 Y4
32.768KHZ
L PC
Por t 0
On B oar d USB 2
C onnector
EC
Por t 1 8x16 K eyboar d
On B oar d USB 3 W inbond W PC E 775L A 0DG
C onnector P21
XTAL
P18
C ar d R eader Por t 3
Y1
12MHZ A lcor A U6433 P21 XTAL SPI PS/2
Y3
32.768KHZ
F L A SH T ouchPA D
2M bytes C onnector
P18 P21
4 Chapter 1
Your Notebook Tour
This section provides an overview of the features and functions of the notebook.
LCD View
Microphone Webcam
Icon Item Description

Webcam Web camera for video communication.
Microphone Internal microphone for sound recording.
Top View
Status Power
indicators button
Keyboard
Status Touchpad
indicators

HDD Indicates when the HDD is active.
Num Lock Lights up when the Num Lock is activated.
Caps Lock Lights up when the Caps Lock is activated.
Keyboard For entering data into your computer
Chapter 1 5
Touchpad Touch-sensitive pointing device which functions like a computer
mouse.
Power Indicates the computer’s power status.
Battery Indicates the computer’s battery status.

1. Charging: The light shows amber when the light is charging.
2. Fully charged: the light shows blue when in AC mode.
Bluetooth Indicates the status of Bluetooth communication (only for certain
models)
Communication Indicates the status of WLAN/3G communication.

indicator
Click buttons The left and right buttons function like the left and right mouse
(left, and right) buttons.
Palmrest Comfortable support area for your hand when using the computer.
Power button/ Turns the computer on and off.
indicator
Closed Front View
Bluetooth Wireless LAN/3G Speakers

communication communication
switch switch (optional)

Bluetooth Enables/disables the Bluetooth function.
communication
switch
3G/Wireless LAN Enables/disables the 3G/Wireless LAN function.
communication
switch
Speakers Left and right speakers deliver stereo audio output.
6 Chapter 1
Left View
Monitor Power Ventilation HDMI out USB

port connector fan jack port

External display Connects to a display device (e.g. external, LCD monitor, LCD
(VGA) port projector).
DC-in jack Connects to an AC adapter.
Ventilation slots Enable the computer to stay cool, even after prolonged use.
HDMI HDMI port Supports high definition digital video connections.
USB 2.0 port Connects to USB 2.0 devices (e.g., USB mouse, USB camera).
Right View
Memory card Headphone Microphone USB port Kensington Ethernet

reader jack jack lock slot jack

Multi-in-one card Accepts Secure Digital (SD), MultiMediaCard(MMC), Memory
reader Stick(MS), Memory Stick PRO (MS PRO), xD-Picture Card (xD).
Note: Push to remove/install the card. ONly one card can operate
at any given time.
Headphones/ Connects to audio line-out devices (e.g., speakers, headphones).

speaker/line-out
jack with S/PDIF
support.
Microphone-in Accepts inputs from external microphones.
jack
USB 2.0 port Connects to USB 2.0 devices (e.g. USB mouse).
Kensington lock Connects to a Kensington-compatible computer security lock.

slot
Ethernet RJ-45) Connects to an Ethernet 10/100/1000-based network.
port
Chapter 1 7
Base View
Battery
Battery Battery
lock latch
Ventilatio
Hard drive slots and
bay cooling fa
Memory
bay
Wireless
module
bay

Battery bay Houses the computer’s battery pack.
Note: The battery shown is for reference only. Your PC may have a
different battery depending on the model purchased.
Battery lock Locks the battery in position
Hard disk bay Houses the computer’s hard disk (secured with screws)
Memory Houses the computer’s main memory.

compartment
Ventilation slots Enable the computer to stay cool, even after prolonged use.
and cooling fan Note: Do not cover or obstruct the opening the fan.
Battery release Releases the battery for removal.
latch
Rear View
Battery

Battery bay Houses the computer’s battery pack.
Note: The battery shown is for reference only. Your PC may have a
different battery depending on the model purchased.
8 Chapter 1
Indicators
The computer has several easy-to-read status indicators. The battery indicator is visible even when the
computer cover is closed.
Icon Function Description

Power Indicates the computer is on or off.
Battery Indicates the computer's battery status.
Bluetooth Indicates the status of Bluetooth communication.
Wireless LAN Indicates the status of Wireless LAN communication.
HDD Indicates when the hard disk drive is active.
Num Lock Lights up when Num Lock is activated.
Caps Lock Lights up when Caps Lock is activated.
NOTE: 1. Charging: The battery light shows amber when the battery is charging. 2. Fully charged: The light
shows green when in AC mode.
Chapter 1 9
TouchPad Basics
The following items show you how to use the TouchPad:
2 3
• Move your finger across the TouchPad (1) to move the cursor.
• Press the left (2) and right (3) buttons located beneath the TouchPad to perform selection and
execution functions. These two buttons are similar to the left and right buttons on a mouse.
Tapping on the TouchPad is the same as clicking the left button.
Function Left Button (2) Right Button (3) Main TouchPad (1)
Execute Quickly click twice. Tap twice (at the same speed
as double-clicking a mouse
button).
Select Click once. Tap once.
Drag Click and hold, then use Tap twice (at the same speed
finger on the TouchPad to as double-clicking a mouse
drag the cursor. button); rest your finger on
the TouchPad on the second
tap and drag the cursor.
Access Click once.
context menu
NOTE: When using the TouchPad, keep it - and your fingers - dry and clean. The TouchPad is sensitive to
finger movement; hence, the lighter the touch, the better the response. Tapping too hard will not
increase the TouchPad’s responsiveness.
10 Chapter 1
Using the Keyboard
Your computer has a close-to-full-sized keyboard and an embedded numeric keypad, separate cursor, lock,
function and special keys.
Lock Keys and embedded numeric keypad

The keyboard has three lock keys which you can toggle on and off.
Lock key Description

Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase.
Num Lock When Num Lock is on, the embedded keypad is in numeric mode. The keys
<Fn> + <F11> function as a calculator (complete with the arithmetic operators +, -, *, and /). Use
this mode when you need to do a lot of numeric data entry. A better solution
would be to connect an external keypad.
Scroll Lock <Fn> + When Scroll Lock is on, the screen moves one line up or down when you press
<F12> the up or down arrow keys respectively. Scroll Lock does not work with some
applications.
The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters
located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols
are not printed on the keys.
Desired access Num Lock on Num Lock off
Number keys on Type numbers in a normal manner.
embedded keypad
Cursor-control keys on Hold <Shift> while using cursor- Hold <Fn> while using cursor-
embedded keypad control keys. control keys.
Main keyboard keys Hold <Fn> while typing letters on Type the letters in a normal
embedded keypad. manner.
Chapter 1 11
Windows Keys
The keyboard has two keys that perform Windows-specific functions.
Key Description
Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button;
it launches the Start menu. It can also be used with other keys to provide a variety of
functions:
< >: Open or close the Start menu
< > + <D>: Display the desktop
< > + <E>: Open Windows Explore
< > + <F>: Search for a file or folder
< > + <L>: Lock your computer (if you are connected to a network domain), or
switch users (if you're not connected to a network domain)
< > + <M>: Minimizes all windows
< > + <R>: Open the Run dialog box
< > + <U>: Open Ease of Access Center
< > + <BREAK>: Display the System Properties dialog box
< > + <TAB>: Cycle through programs on the taskbar
<CTRL> + < > + <F>: Search for computers (if you are on a network)
Note: Depending on your edition of Windows XP, some shortcuts may not function
as described.
Application This key has the same effect as clicking the right mouse button; it opens the
key application's context menu.
12 Chapter 1
Hot Keys
The computer employs hotkeys or key combinations to access most of the computer's controls like screen
brightness and volume output.
To activate hotkeys, press and hold the <Fn> key before pressing the other key in the hotkey combination.
Hotkey Icon Function Description

<Fn> + <F2> System Properties Display the System Properties dialog box.
<Fn> + <F3> Bluetooth Enables/disables the Bluetooth function.
communication switch
<Fn> + <F4> Sleep Puts the computer in Sleep mode.
<Fn> + <F5> Display toggle Switches display output between the display
screen, external monitor (if connected) and
both.
<Fn> + <F6> Screen blank Turns the display screen backlight off to save
power. Press any key to return.
<Fn> + <F8> Speaker toggle Turns the speakers on and off.
<Fn> + < > Brightness up Increases the screen brightness.
<Fn> + < > Brightness down Decreases the screen brightness.
<Fn> + < > Volume up Increases the sound volume.
<Fn> + < > Volume down Decreases the sound volume.
Chapter 1 13
Special Keys
You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your
keyboard.
The Euro symbol

1. Open a text editor or word processor.
2. Hold <Alt Gr> and then press the <5> key at the upper-center of the keyboard.
NOTE: Some fonts and software do not support the Euro symbol. See www.microsoft.com/typography/faq/
faq12.htm for more information.
The US dollar sign

1. Open a text editor or word processor.
2. Hold <Shift> and then press the <4> key at the upper-center of the keyboard.
NOTE: This function varies according to the language settings.
14 Chapter 1
Hardware Specifications and Configurations
Processor
Item Specification
CPU type Intel Penryn SFF (ULV)
CPU package Micro-FCBGA 956 balls
Chipset • Intel Crestline GS45 SFF and ICH9M SFF
Features • Supports Intel architecture with Dynamic execution.
• On-die, primary 32-kB instruction cache and 32-kB write-back
data
• cache.
• On-die, up to 3MB second level shared cache with advanced
transfer
• cache architecture.
• Streaming SIMD Extensions 2 (SSE2),Streaming SIMD
Extensions 3
• (SSE3)
• Supplemental streaming SIMD extensions 3 (SSSE3) and
SSE4.1
• instructionsets.
• 800MHz source-synchronous front side bus (FSB)
• Advanced power management features including Enhanced
Intel
• SpeedStep®
• Technology and dynamic FSB frequency switching.
• Digital thermal sensor (DTS).
• Execute disable bit support for enhanced security.
• Intel® Dynamic Acceleration Technology and Enhanced Multi
• Threaded
• Thermal Management (EmTTM).
• Support enhanced Intel Virtualization Technology.
Processor Specifications
CPU Mfg FSB Cache
Item Cores Package Power Acer P/N
Speed Tech Speed Size
Core2Solo 1.4G 1 45nm 800 3M BGA 5.5W KC.35B0
SU3500 MHz 1.SSU
Celeron 1.2G TBC 45nm 800 1M BGA 10W KC.NB00
723 MHz 1.723
Core2Duo TBC 2 45nm 800 2M BGA TBC KC.41B0
SU4100 MHz 1.DSU
CPU Fan True Value Table

CPU Temperature
Fan Speed (RPM) SPL Spec (dBA)
(Celcius)
38 2400 23
43 3300 26
50 4000 29
56 4500 31
Chapter 1 15
Throttling 50%: On= 90°C; OFF=80°C
OS shut down at 95°C; H/W shut down at 85°C
North Bridge Specifications
Item Specification
Chipset Intel Crestline GS45 SFF
Package FCBGA 1363 balls
Features • Processor hosts bus supports 667/800/1066MHz FSB support.
• Supports Dual Channel DDR2 SDRAM at 667/800MHz
• Integrated SDRAM controller up to 8GB (2 SODIMM support)
• DMI x2 and DMI x4 for connection between GMCH and ICH9M
South Bridge Specifications

Item Specification
Chipset ICH9M SFF
Package BGA 676 balls
Features • Upstream accelerated Hub architecture interface for access to
GMCH.
• PCI Express Base Specification, Revivsion 1.1 support.
• PCI 2.3 interface. (4 PCI Request/Grant pairs).
• ACPI Power Management Logi Support.
• Enhanced DMA controller, interupt controller, timers functions.
• Integrated Serial ATA host controllers with independent DMA
operation on six ports and AHCI support.
• USB 1.1 and USB 2.0 Host controllers.
• Supports Intel High Definition Audio (Intel HD Audio) Interface.
• Supports Intel® Matrix Storage Technology.
• Supports Intel® Active Mangement Technology.
• Low Pin Count (LPC) interface.
• 6 PCle ports.
System Memory
Item Specification
Memory size 0MB (No on-board Memory)
DIMM socket number 2 sockets
Supports memory size per socket 2GB
Supports maximum memory size 4GB for 64bit OS (with two 2GB SO-DIMM)
Supports DIMM type DDR2 Synchronous DRAM
Supports DIMM Speed 800/667 MHz
Video Specifications
Item Specification
Chipset Intel® GS45 Express Chipset
Package • 1329-ball FCBGA
• Size: 34mm x 34mm
• Ball pitch: 0.7mm
16 Chapter 1
Item Specification
Features • Microsoft Windows Vista* Premium support with the highest
level of Windows Aero* experience
• Blu-ray* logo capable HD video playback, with native support
for Blu-ray* drives
• Great 3D graphics performance
• Intel® Clear Video Technology for excellent video quality
Hard Disk Drive Interface
Item Specifications
Vendor & Hitachi Hitachi Hitachi Hitachi Hitachi Hitachi
Model HTS545050B HTS545032B HTS545025B HTS545016B HTS543225L HTS543216L9
Name 9A300 9A300 9A300 9A300 9A300 SA00
Capacity 500 320 250 160 250 160

(GB)
Bytes per 512
sector
Data heads 4 3 2 2 3 2
Drive Format
Disks 2 2 1 1 2 1
Spindle 5400
speed
(RPM)
Performance Specifications
Buffer size 8MB
Interface SATA
Internal 3GB/s maximum 1.5GB/s
transfer maximum
rate (Gbits/
sec, max)
I/O data 875 Mbits/s maximum 845 Mbits/s 775Mbits/s 729Mbits/s
transfer maximum maximum maximum
rate
(Mbytes/
sec max)
DC Power Requirements
Voltage +5.0V ± 5%.
Item Specifications
Vendor & Model Seagate Seagate Seagate Seagate
ST9160310AS ST9250315AS ST9320320AS ST9500325AS
Name
Capacity (GB) 160 250 320 500
Bytes per sector 512 512 512 512
Data heads 2 2 4 4
Drive Format
Disks 1 1 2 2
Spindle speed 5400 5400 5400 5400

(RPM)
Chapter 1 17
Item Specifications
Buffer size 8 MB 8 MB 8MB 8 MB
Interface SATA SATA SATA SATA
Internal transfer 830 1175 830 1175

rate (Mbits/sec,
max)
I/O data transfer 875 Mbits/s maximum 845 Mbits/s
rate maximum
(Mbytes/sec
max)
Voltage +5.0V ± 5%.
Item Specifications
Vendor & Model Toshiba Toshiba Toshiba Toshiba
MK1655GSX MK2555GSX MK3255GSX MK5055GSX
Name
Capacity (GB) 160 250 320 500
Bytes per sector 512 512 512 512
Data heads 2 2 4 4
Drive Format
Disks 1 1 2 2
Spindle speed 5400

(RPM)
Buffer size 8MB
Interface SATA
Internal transfer 363 ~ 952 typical

rate (Mbits/sec,
max)
I/O data transfer 300
rate
(Mbytes/sec
max)
Voltage 5V ±5%
Item Specifications
Vendor & Model Western Digital Western Digital Western Digital Western Digital
WD1600BEVT- WD2500BEVT-22ZCT0 WD3200BEVT-22ZCT0 WD5000BEVT-22ZAT0
Name 22ZCTO
Capacity (GB) 160 250 320 500
Bytes per sector 512
Data heads 2 4 3 4
Drive Format
Disks 1 2 2 2
18 Chapter 1
Item Specifications
Spindle speed 5400
(RPM)
Buffer size 8 MB
Interface SATA
Internal transfer N/A

rate (Mbits/sec,
max)
I/O data transfer 300
rate
(Mbytes/sec
max)
Voltage 5V ±5%
BIOS
Item Specification
BIOS vendor Insyde
BIOS Version 3.5
BIOS Features • Flash ROM 1MB
• Support ISIPP
• Support Acer UI
• Support multi-boot
• Suspend to RAM (S3) / Disk (S4)
• Various hot-keys for system control
• Support SMBUS 2.0, PCI2.3
• ACPI 2.0 compliance with Intel Speed Step Support C1e, C2,
C3 and S3, S4,S5 for mobile CPU.
• DMI utility for BIOS serial number configuration/asset tag
• Support PXE
• Support Y2K solution
• Support Win Flash Wake on LAN from S3
• Wake on LAN form S4 in AC mode
• System information
LCD 11.6”
Item Specifications
Vendor/model name AUO CMO N116B6-L02 LG LP116WH1- Samsung
B11.6XW02 TLA1 LTN116AT01-A01
Screen Diagonal (mm) 11.6” 11.6” 11.6” 11.6”
Display Area (mm) 256.125 x 144 (11.6” diagonal)
Display resolution (pixels) 1366 x 768 1366 x 768 1366 x 768 1366 x 768
Pixel Pitch (mm) 0.1875 x 0.1875 0.1875 x 0.1875 0.1875 x 0.1875 0.2265(H) x
0.2265(V)
Typical White Luminance (cd/m2) 200 200 200 200
also called Brightness

Contrast Ratio 500:1 500:1 500:1 500:1
Response Time (Optical Rise 8 7 8 8

Time/Fall Time) msec
Chapter 1 19
Item Specifications
Typical Power Consumption 4.0 4 4 2.85
(watt)
Weight (without inverter) 255g 225g 255g 255g
Physical Size (mm) 268 (L) x 161.5 268 x 161.5 x 5 268.0 x 161.5 268.0 x 161.5
(W)
Electrical Interface LVDS LVDS LVDS LVDS
Viewing Angle (degree)

45/45 45/45 45/45 TBD
Horizontal (Right) / (Left) 20/40 20/45 20/40
Vertical (Upper) / (Lower)
Bluetooth
Item Specification
Bluetooth Controller Bluetooth module Foxconn Bluetooth BRM 2046 BT2.1 (T60H928.33) F/
W:861
Features • Fully Qualified Bluetooth v2.1 with Class 2 specification RF output
power.
• Enhanced Data Rate (EDR) compliant.
• Full Piconet and Scatternet operation.
• Integrated PIFA Antenna with better RF performance.
• USB 2.0 compliant interface.
• F/W upgradable via Flash downloads.
• Very low power consumption.
• Support Coexistence with Intel WCS (Wireless Coexistence System)
& AFH (Adaptive Frequency Hopping).
Audio Codec and Amplifier

Item Specification
Audio Realtek ALC269X
Controller
Features • Headphone-out with S/PDIF, Line-In and Microphone-In.
• 2 stereo ADCs support 16/20/24-bit PCM format recording simultaneously.
LAN Interface
Item Specification
LAN Chipset ATHEROS AR8131L
Package 48pin QFN
20 Chapter 1
Item Specification
Features • The AR8131L is the third generation Gigabit Ethernet
(GbE) controller solution from Atheros. It is an ultra-high
performance, ultralow cost, and ultra-low power fully
integrated 10/100/1000 Mbps NIC/LOM Ethernet
controller perfectly suited for both PC and embedded
applications.
• The AR8131L combines a 10/100/1000BASE-T GbE
media access controller (MAC), a triplespeed Ethernet
physical layer transceiver (PHY), and a PCI Express bus
interface.
• The AR8131L is compliant with IEEE 802.3u
specification for 10/100 Mbps Ethernet and IEEE
802.3ab specification for 1000 Mbps Ethernet.
• The AR8131L device combines pulse shaping, Tx/Rx
PCS, echo canceller, NEXT canceller, equalizer,
decoder, and timing recovery functions to deliver robust
signal performance in noisy environments.
• The AR8131L GbE controller supports checksum offload
features for IP, TCP, and UDP,
Keyboard
Item Specification
Type ACER NT1T JM11 Black
Total number of keypads 86/87/91
Windows logo key Yes
Internal & external keyboard work Yes
simultaneously
Features • Supports application keys for Windows XP version
Media Card Reader

Item Specification
Chipset Alcor AU6433
Features • Fully compatible with USB2.0 High Speed and backward
compatible with USB1.1 specifications
• Supports multiple flash card interfaces, including SD/
MMC/xD/MS.
• Supports single LUN
• 48-pin LQFP
Camera
Item Specifications
Vendor and model Lite On Suyin Chicony
Model No. 09P2SF001 Model No.CN0316- CNF9011
S30C-OV06-1
Type 640 x 480 VGA (0.3M) 640 x 480 VGA (0.3M) 640 x 480 VGA (0.3M)
size 1/6” CMOS size 1/6” CMOS size 1/6” CMOS
Interface USB 2.0 high speed USB 2.0 high speed USB 2.0 high speed
interface interface interface
Optical aperture F2.4 F2.4 F2.4 ± 5%
Focusing range 18.65~Infinite, focus on 40 cm to Infinity 17.4cm ~ Infinity, focus
48cm on 40cm
Chapter 1 21
Item Specifications
Dimensions (L x W x H 65 x 8 x 3.84 +/- 0.25 65X 7.9X 3.8+/-0.2mm 64.8±0.3 X 7.9±0.1 X
mm) (H) mm 3.64+0.15/-0.25 mm
Sensor type CMOS (OV9710) CMOS image sensor CMOS
Pixel resolution 640x480 640X480 640 x 480
Pixel size TBD 3.6um X3.6um TBD
Image size TBD 2.36mm(H) TBD
X1.76mm(V)
Wireless LAN
Item Specification Specification Specification Specification
Type Atheros HB93 Intel MM#903341 Intel MM#897072 Intel MM#895373
1x2 BGN
802.11g
Radio Technology IEEE 802.11g standard compliant
Operating 2412 ~ 2484MHz ISM band
Frequency
Modulation OFDM, DQPSK, DBPSK and CCK
Schemes
Channel Numbers • 1---11 channels for active channels
• 12---13 channels for passive channels
Data Rate 54Mbps with fall back rates of 48, 36, 24, 18, 12, 9 and 6Mbps
Media Access CSMA/CA with ACK
Protocol
Transmitter Output Typical 13.5 dBm for 54Mbps
Power
802.11b
Radio Technology IEEE 802.11b Direct Sequence Spread Spectrum
Operating 2412 ~ 2484MHz ISM band
Frequency
Modulation DQPSK, DBPSK and CCK
Schemes
Channel Number • 1---11 channels for active channels
• 12---13 channels for passive channels
Data Rate 11Mbps with fall back rates of 5.5, 2, and 1Mbps
Media Access CSMA/CA with ACK
Protocol
Transmitter Output 18dBm typically
Power
Battery
Specification
Item
6 Cell
Vendor & model name SANYO UM-2009E Li-Ion 3S2P
PANASONIC UM-2009E Li-Ion 3S2P
SIMPLO UM-2009E Li-Ion 3S2P
SIMPLO UM-2009E Li-Ion 3S2P
Battery Type Li-ion
22 Chapter 1
Specification
Item
6 Cell
Pack capacity SANYO 6 cell 4400mAh
SANYO 6 cell 5600mAh
PANASONIC 6 cell 4400mAh
PANASONIC 6 cell 5800mAh
SAMSUNG 6 cell 4400mAh
SAMSUNG 6 cell 5600mAh
LGC 6 cell 5600mAh
Number of battery cell 6
Package configuration 3 cells in series, 2 series in parallel
Chapter 1 23
24 Chapter 1
Chapter 2
System Utilities
BIOS Setup Utility

The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/
Output System).
Your computer is already properly configured and optimized, and you do not need to run this utility. However, if
you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4
Troubleshooting when problem arises.
To activate the BIOS Utility, press F2 during POST (when Press <F2> to enter Setup message is prompted
on the bottom of screen).
Press F2 to enter setup. The default parameter of F12 Boot Menu is set to “disabled”. If you want to change
boot device without entering BIOS Setup Utility, please set the parameter to “enabled”.
Press <F12> during POST to enter multi-boot menu. In this menu, user can change boot device without
entering BIOS SETUP Utility.
Navigating the BIOS Utility

There are six menu options: Information, Main, Advanced, Security, Power, Boot, and Exit.
Follow these instructions:
• To choose a menu, use the left and right arrow keys.
• To choose an item, use the up and down arrow keys.
• To change the value of a parameter, press F5 or F6.
• A plus sign (+) indicates the item has sub-items. Press Enter to expand this item.
• Press Esc while you are in any of the menu options to go to the Exit menu.
• In any menu, you can load default settings by pressing F9. You can also press F10 to save any
changes made and exit the BIOS Setup Utility.
NOTE: You can change the value of a parameter if it is enclosed in square brackets. Navigation keys for a
particular menu are shown on the bottom of the screen. Help for parameters are found in the Item
Specific Help part of the screen. Read this carefully when making changes to parameter values. Please
note that system information is subject to different models.
Chapter 2 25
Information
The Information screen displays a summary of your computer hardware information.
InsydeH20 Setup Utility Rev. 3.5

Information Main Security Boot Exit
CPU Type Intel(R) Core(TM)2 Solo CPU

CPU Speed 1.40GHz
HDD Model Name: Hitachi HTS545032B9A300

HDD Serial Number: 090515PB5C06QDGYRDWG
ATAPI Model name: None
System BIOS Version: v0.1108h

VGA BIOS Version: Intel V1800
Serial Number: ZH7OSK01C1924125A42500

Asset Tag Number: 2020202020202020202020202020202020
Product Name:
Manufacturer Name: Acer
UUID: 497CDC77E0224E159D78ACE77B820EBC
F1 Help Select Item F5/F6 C h a n g e Va l u e s F9 Setup Default

ESC Exit Select Menu Enter Select SubMenu F10 Save and Exit
NOTE: The system information is subject to different models.
Parameter Description
CPU Type This field shows the CPU type and speed of the system.
CPU Speed This field shows the speed of the CPU.
HDD Model Name This field shows the model name of HDD installed on primary IDE master.
HDD Serial Number This field displays the serial number of HDD installed on primary IDE master.
ATAPI Model Name This field displays the model name of the installed ODD drive.
System BIOS Version Displays system BIOS version.
VGA BIOS Version This field displays the VGA firmware version of the system.
Serial Number This field displays the serial number of this unit.
Asset Tag Number This field displays the asset tag number of the system.
Product Name This field shows product name of the system.
Manufacturer Name This field displays the manufacturer of this system.
UUID Number Universally Unique Identifier (UUID) is an identifier standard used in software
construction, standardized by the Open Software Foundation (OSF) as part of
the Distributed Computing Environment (DCE).
26 Chapter 2
Main
The Main screen allows the user to set the system time and date as well as enable and disable boot option
and recovery.

Item Specific Help

System Time: [19:10:59]
System Date: [06/09/2009]
This is the help for the
System Memory: 640 K hour field. Valid range
Total Memory: 4096 MB is from 0 to 23.
Video Memory: [64MB] INCREASE/REDUCE: F 5 / F 6
Quiet Boot [Enabled]

Network Boot [Enabled]
F12 Boot Menu [Disabled]
D2D Recovery [Enabled]
SATA Mode [AHCI Mode]
F1 Help Select Item F 5 / F 6 C h a n g e Va l u e s F9 Setup Default

ESC Exit Select Menu Enter Select SubMenu F 10 Save and Exit
NOTE: The screen above is for your reference only. Actual values may differ.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter Description Format/Option
System Time Sets the system time. The hours are displayed with 24- Format: HH:MM:SS
hour format. (hour:minute:second)
System Date Sets the system date. Format MM/DD/YYYY
(month/day/year)
System Memory This field reports system memory size. N/A
Total Memory This field reports the memory size of the system. N/A
Memory size is fixed to 4096MB.
Video Memory Shows the video memory size. VGA Memory size=32 MB N/A
Quiet Boot This will hide POST messages while booting. Option: Enabled or Disabled
Network Boot Enables, disables the system boot from LAN (remote Option: Enabled or Disabled
server).
F12 Boot Menu Enables, disables Boot Menu during POST. Option: Enabled or Enabled
D2D Recovery Enables, disables D2D Recovery function. The function Option: Enabled or Disabled
allows the user to create a hidden partition on hard disc
drive to store operation system and restore the system
to factory defaults.
SATA Mode Control the mode in which the SATA controller should Option: AHCI or IDE
operate.
Chapter 2 27
Security
The Security screen contains parameters that help safeguard and protect your computer from unauthorized
use.

Item Specific Help

Supervisor Password Is: Clear
User Password Is: Clear
HDD Password Is: Clear Install or Change the
password and the length
Set Supervisor Password of password must be
Set User Password greater than one word.
Set Hdd Password
Power on password [Disabled]

The table below describes the parameters in this screen. Settings in boldface are the default and suggested
parameter settings.
Parameter Description Option
Supervisor Password Is Shows the setting of the Supervisor password Clear or Set
User Password Is Shows the setting of the user password. Clear or Set
Set Supervisor Password Press Enter to set the supervisor password. When
set, this password protects the BIOS Setup Utility
from unauthorized access. The user can not either
enter the Setup menu nor change the value of
parameters.
Set User Password Press Enter to set the user password. When user
password is set, this password protects the BIOS
Setup Utility from unauthorized access. The user can
enter Setup menu only and does not have right to
change the value of parameters.
Set Hdd Password Enter HDD password.
Power on password Defines whether a password is required or not while Enabled or
the events defined in this group happened. The Disabled
following sub-options are all requires the Supervisor
password for changes and should be grayed out if the
user password was used to enter setup.
NOTE: When you are prompted to enter a password, you have three tries before the system halts. Don’t forget
the password. If you forget the password, you may have to reset the computer.
Setting a Password
Follow these steps as you set the user or the supervisor password:
28 Chapter 2
1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The
Set Supervisor Password box appears:
Set Supervisor Password
Enter New Password [ ]

Confirm New Password [ ]
2. Type a password in the “Enter New Password” field. The password length can not exceeds 8
alphanumeric characters (A-Z, a-z, 0-9, not case sensitive). Retype the password in the “Confirm New
Password” field.
IMPORTANT:Be very careful when typing your password because the characters do not appear on the screen.
3. Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
4. If desired, you can opt to enable the Password on boot parameter.
5. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
Removing a Password
Follow these steps:
Set Password box appears:
Enter Current Password [ ]

2. Type the current password in the Enter Current Password field and press Enter.
3. Press Enter twice without typing anything in the Enter New Password and Confirm New Password fields.
The computer then sets the Supervisor Password parameter to “Clear”.
4. When you have changed the settings, press u to save the changes and exit the BIOS Setup Utility.
Chapter 2 29
Changing a Password
Set Password box appears.
Enter Current Password [ ]

2. Type the current password in the Enter Current Password field and press Enter.
3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password
field.
4. Press Enter. After setting the password, the computer sets the User Password parameter to “Set”.
5. If desired, you can enable the Password on boot parameter.
6. When you are done, press F10 to save the changes and exit the BIOS Setup Utility.
If the verification is OK, the screen will display as following.
Setup Notice
Changes have been saved.
[Continue]
The password setting is complete after the user presses Enter.

If the current password entered does not match the actual current password, the screen will show you the
Setup Warning.
Setup Warning
Invalid Password.
[Continue]
If the new password and confirm new password strings do not match, the screen displays the following
message.
Setup Warning
Passwords do not match.

Re-enter password.
[Continue]
30 Chapter 2
Boot
This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices
includes the USB diskette drives, the onboard hard disk drive and the DVD drive in the module bay.

Item Specific Help

Boot priority order:
1. IDE0 : Hitachi HTS545032B9A300 Use < > or < > to select

2. IDE1 : a device, then press
3. Network Boot : Atheros Boot Agent <F5> to move it down the
4. USB HDD list, or <F6> to move
5. USB CDROM : it up the list. Press
6. USB FDD : <Esc> to escape the menu

Chapter 2 31
Exit
The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility.

Item Specific Help

Exit Saving Changes
Exit Discarding Changes
Load Setup Defaults Exit System Setup and
Discard Changes save your changes.
Save Changes

The table below describes the parameters in this screen.

Parameter Description
Exit Saving Changes Exit System Setup and save your changes to CMOS.
Exit Discarding Exit utility without saving setup data to CMOS.
Changes
Load Setup Default Load default values for all SETUP item.
Discard Changes Load previous values from CMOS for all SETUP items.
Save Changes Save Setup Data to CMOS.
32 Chapter 2
BIOS Flash Utility
The BIOS flash memory update is required for the following conditions:
• New versions of system programs
• New features or options
• Restore a BIOS when it becomes corrupted.
Chapter 2 33
DOS Flash Utility
Perform the following steps to use the DOS Flash Utility:
1. Press F2 during boot to enter the Setup Menu.
2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move
USB HDD to position 1.

Item Specific Help

Boot priority order:
1. IDE0 : Hitachi HTS545032B9A300 Use < > or < > to select

2. IDE1 : a device, then press
3. Network Boot : Atheros Boot Agent <F5> to move it down the
4. USB HDD list, or <F6> to move
5. USB CDROM : it up the list. Press
6. USB FDD : <Esc> to escape the menu

3. Execute the FLASH.BAT batch file to update BIOS. Or enter C:\ Flash it bios ver.fd/dc
The flash process begins as shown.
4. In flash BIOS, the message Please do not remove AC Power Source displays.
NOTE: If the AC power is not connected, the following message displays.
Plug in the AC power to continue.

5. Flash is complete when the message Flash programming complete displays.
34 Chapter 2
WinFlash Utility
Perform the following steps to use the WinFlash Utility:
1. Double click the WinFlash executable.
2. Click OK to begin the update. A progress screen displays.
3. When the process is complete, close all programs and applications and reboot the system.
Chapter 2 35
Remove HDD/BIOS Password Utilities
This section provide you with removing HDD/BIOS method:
Remove HDD Password:
When the user keys in the wrong password three times, the system reports the following error code to user.
To unlock the HDD password, perform the following steps:

1. Press Enter to display the Select Item screen.
2. Select Enter Unlock Password and press Enter.

An Unlock Password displays.
3. Make a note of the key, 76943488 in the example.

4. Boot up the system to a removable bootable drive containing DOS and the UnlockHD.EXE program and
open a DOS prompt. For instructions on changing boot priority see “Boot” on page 31.
5. From the DOS prompt, enter the UnlockHD.EXE command and input the key to create an unlock code.
Make a note of the result, for example 46548274.
6. Reboot to the hard disk and wait for the error code to reappear.
7. Press Enter to display the Select Item screen.
8. Select Enter Unlock Password and press Enter.
9. Enter the unlock code generated by UnlockHD.EXE.
10. Save and exit the BIOS to complete the process.
36 Chapter 2
Removing BIOS Passwords:
If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the
image below.
To reset the BIOS password, run clnpwd.exe as follows:

1. From a DOS prompt, Execute clnpwd.exe
2. Press 1 or 2 to clean the desired password shown on the screen.

The onscreen message determines whether the function is successful or not.
Chapter 2 37
Miscellaneous Utilities
Using Boot Sequence Selector

Boot Sequence Selector allows the boot order to be changes without accessing the BIOS. To use Boot
Sequence Selector, perform the following steps:
1. Enter into DOS.
2. Execute BS.exe to display the usage screen.
3. Select the desired boot sequence by entering the corresponding sequence, for example, enter BS2 to
change the boot sequence to HDD|CD ROM|LAN|Floppy.
Using DMITools
The DMI (Desktop Management Interface) Tool copies BIOS information to eeprom to be used in the DMI pool
for hardware management.
When the BIOS displays Verifying DMI pool data it is checking the table correlates with the hardware before
sending to the operating system (Windows, etc.).
To update the DMI Pool, perform the following steps:
1. Enter into DOS.
2. Execute dmitools.exe. The following messages show dmitools usage:
IMPORTANT:The following write examples (2 to 5) require a system reboot to take effect
38 Chapter 2
Example 1: Read DMI Information from Memory
Input:
dmitools /r
Output:
Manufacturer (Type1, Offset04h): Acer
Product Name (Type1, Offset05h): Aspire one xxxxx
Serial Number (Type1, Offset07h): 01234567890123456789
UUID String (Type1, Offset08h): xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx
Asset Tag (Type3, Offset04h): Acer Asstag
Example 2: Write Product Name to EEPROM

Input:
dmitools /wp Acer
Example 3: Write Serial Number to EEPROM

Input:
dmitools /ws 01234567890123456789
Example 4: Write UUID to EEPROM

Input:
dmitools /wu
Example 5: Write Asset Tag to EEPROM

Input:
dmitools /wa Acer Asstag
Using the LAN MAC Utility

Perform the following steps to write MAC information to eeprom:
1. Use a text editor, for example Notepad, to edit the MAC.CFG file as shown:
• WriteData= '001122334455' <------- MAC value

• StartAddr=7A <------- MAC address
• WriteLeng=6 <------- MAC value length
• KeepByte=0 <------- can be any value
2. Boot into DOS.
3. Execute MAC.BAT to write MAC information to eeprom.
Chapter 2 39
40 Chapter 2
Chapter 3
Machine Disassembly and Replacement

This chapter contains step-by-step procedures on how to disassemble the notebook computer for
maintenance and troubleshooting.
Disassembly Requirements
To disassemble the computer, you need the following tools:
• Wrist grounding strap and conductive mat for preventing electrostatic discharge
• Flat screwdriver
• Philips screwdriver
• Plastic flat screwdriver
• Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Related Information
The product previews seen in the disassembly procedures may not represent the final product color or
configuration.
IMPORTANT: Cable paths and positioning may not represent the actual model. During the removal and
replacement of components, ensure all available cable channels and clips are used and that the cables are
replaced in the same position.
Replacement Requirements
NOTE: Cabling and components require adhesive to be applied during the replacement and reassembly
process.
NOTE: During manufacture a cyanoacrylate glue is used provided by Holdtite Adhesives LTD. This is not a
specified requirement. The reassembler is free to select an alternative appropriate adhesive.
Chapter 3 41
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
3. Place the system on a flat, stable surface.
42 Chapter 3
Disassembly Process
The disassembly process is divided into the following sections:
• External components disassembly
• Main unit disassembly
• LCD module disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you
want to remove the Mainboard, you must first remove the Keyboard, and LCD Module then disassemble the
inside assembly frame in that order.
Main Screw List
Screw Quantity Acer Part Number
M2.0X2.5-I(BNI)(NYLOK) IRON 4 86.SA107.002
M2*3.0 I (BNI,NYLOK)IRON 16 86.SA107.001
M2*5-I(BZN)(NYLOK) 20 86.TG607.004
Chapter 3 43
External Module Disassembly Process
NOTE: The product previews seen in the disassembly procedures may not represent the final product color or
configuration.
Screw List
Step Screw Quantity Part No.
WAN Module 2*3 1 86.SA107.001
Disassembly
External Modules Disassembly Flowchart
Turn off system

and peripherals
power
Disconnect power
and signal cables
from system
Remove
Battery
Remove
Dummy Card
Remove
Lower Covers
Remove Remove Remove

HDD DIMM WLAN Board
44 Chapter 3
Removing the Battery Pack
1. Turn the computer over.
2. Slide the battery lock/unlock latch to the unlock position.
3. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the
main unit (2).
Chapter 3 45
Removing the Dummy Card
1. Press the dummy card in to allow it to spring out.
2. Pull the dummy card out.
46 Chapter 3
Removing the Hard Disk Drive Module
DISCLAIMER: The notebook sample in the following images shows an FFC. The actual model
includes an FPC as pictured in the image on the right.
1. See “Removing the Battery Pack” on page 45.
2. Loosen the four captive screws.
3. Lift the HDD cover up and away by the corner.
4. Grasp the FPC cable and lift to remove.

NOTE: The cable pictured in the following images may differ from the actual sample.
Chapter 3 47
5. Grasp the plastic tab at the top of the HDD and lift to bring the HDD out of its bay. At the same time, hold
the HDD with the other hand and lift to remove from the chassis.
6. Unlock the HDD FPC and pull the FPC away.
48 Chapter 3
Removing the DIMM Module
2. Loosen the four captive screws in the memory cover.
3. Lift the memory cover away.
4. Push outwards the memory module clips.
Chapter 3 49
5. Pull the memory module out.
50 Chapter 3
Removing the WLAN Module
1. See “Removing the Battery Pack” on page 45..
2. Loosen the four captive screws in the memory cover.
3. Lift and remove the memory cover.
4. Detach the two cables from the Wireless LAN module.
IMPORTANT:Take note of the Main (1. black) and Auxiliary (2. white) connectors.
Chapter 3 51
5. Remove the one screw. Ensure the cables are well clear of the module
Screw List
Step Screw Quantity Screw Type
WAN Module 2*3 1
Disassembly
6. Pull the WLAN module out and away.
52 Chapter 3
Main Unit Disassembly Process
configuration.
Main Unit Disassembly Flowchart
Remove External
Modules before
proceeding
Remove
Keyboard
Remove Remove
Upper Cover Button Board
Remove
LCD Module

I/O Board Bluetooth Module LED Board
Remove Remove
Mainboard Speaker Module

CRT Board Thermal Module RTC Battery
Chapter 3 53
Screw List
Remove Upper Cover M2*3 3 86.SA107.001
M2*5 18 86.TG607.004
Remove Button Board M2*3 2 86.W4107.002
Remove LCD Module M2*5 2 86.TG607.004
Remove LED Board M2*3 1 86.SA107.001
Remove I/O Board M2*3 1 86.SA107.001
Remove Mainboard M2*3 4 86.SA107.001
54 Chapter 3
Removing the Keyboard
IMPORTANT: The keyboard is easily warped or damaged during the removal process. Take care not to use
excessive force when removing to prevent damage.
2. See “Removing the Hard Disk Drive Module” on page 47.
3. See “Removing the DIMM Module” on page 49.
4. See “Removing the WLAN Module” on page 51.
5. Using the plastic pry, press in the four latches along the top of the keyboard to release the keyboard from
the cover.
NOTE: The keyboard will spring up slightly when all retaining clips are unlocked.
Chapter 3 55
6. Using the plastic pry, lift up the top edge of the keyboard and then lift the keyboard up.
7. Flip the keyboard over.
a. Unlock the FCC b. Pull the keyboard away
56 Chapter 3
Removing the Upper Cover
1. See “Removing the Keyboard” on page 55.
2. Disconnect the button board FCC from the main board by unlocking the FCC cable and pulling away.
3. Remove the nine screws in the upper cover.
Screw List
Step Size Quantity Screw Type
Upper Cover M2*3 3 (blue call out)
Disassembly
M2*5 6 (red call out)
Chapter 3 57
4. Turn the computer over and remove the twelve screws in the bottom cover.
Screw List
Upper Cover M2*5 12
Disassembly
5. Turn the computer over and grasp the upper cover under the top edge. Then pull the upper cover up and
away from the computer.
58 Chapter 3
Removing the Button Board
IMPORTANT: The Touchpad Board cannot be removed individually. To replace the Touchpad, replace the entire
Upper Cover.
1. See “Removing the Upper Cover” on page 57.
2. Unlock and remove the touch-pad to mainboard FCC.
3. Unlock and detach the touch-pad to touch-pad FCC.
4. Remove the two screws holding the button board.
Chapter 3 59
Screw List
Button board M2*3 2
5. Lift the button board away
6. Peel the touch-pad FCC away from the adhesive.
7. Unlock the touch-pad FCC and pull the cable away.
60 Chapter 3
8. Lift up and pull the button board to main board FCC free.
Chapter 3 61
Removing the LCD Module
2. Pull the WLAN cables through and away from the computer.
3. Lift the transparent adhesive tape off the LCD connector.
62 Chapter 3
4. Push out the LCD connector.
5. Remove the two screws of the LCD module hinges.
Screw List
LCD Module M2*5 2
Disassembly
6. Lift the LCD module away.
Chapter 3 63
Removing the LED Board
2. Unlock and remove the LCD board FCC.
3. Remove the single screw securing the LED Board to the Lower Cover.
Screw List
LED Board 2*3 1
Disassembly
64 Chapter 3
4. Lift off the LCD Board.
5. Unlock and remove the LED board FCC from the mainboard.
Chapter 3 65
Removing the Bluetooth Module
2. Detach the Bluetooth module cable from the mainboard.
3. LIft the Bluetooth module away from the

computer.
4. Detach the Bluetooth module cable from the module.
66 Chapter 3
Removing the I/O Board
1. See “Removing the Upper Cover” on page 57..
2. Unlock and remove the I/O board FCC from the main board
3. Unlock and remove the I/O board FCC from the I/O board.
4. Remove the one screw from the I/O board.
Chapter 3 67
Screw List
Step Screw Quantity Screw Type.
I/O Board Disassembly M2*3 1
5. Lift the board up from the internal edge and then pull away diagonally.
68 Chapter 3
Removing the Mainboard
2. See “Removing the LCD Module” on page 62.
3. See “Removing the LED Board” on page 64.
4. See “Removing the Bluetooth Module” on page 66.
5. See “Removing the I/O Board” on page 67.
6. Disconnect the speaker cable from the mainboard.
7. Remove the four screws of the main board and the CRT board.
Screw List
Step Screw Quantity Screw Type.
Main Board 2*3 4
Disassembly
Chapter 3 69
8. Lift the main board and the CRT board out together. Lift the internal edge up first then pull out the external
connector edge.
NOTE: The hand in the photograph holding on to the CRT board.
70 Chapter 3
Removing the CRT Board
1. See “Removing the Mainboard” on page 69.
2. Disconnect the CRT cable from the CRT board.
3. Disconnect the CRT cable from the main board.
Chapter 3 71
Removing the Thermal Module
2. See “Removing the CRT Board” on page 71.
3. Remove the five captive screws of the thermal module.
4. Lift the thermal module up slightly and then disconnect the thermal module cable from the main board.
5. Lift the thermal module away from the main board.
72 Chapter 3
Removing the RTC Battery
IMPORTANT:Observe local regulations in the disposal of all batteries.
2. Pry the RTC battery out of the holding clips.
Chapter 3 73
Removing the Speaker Modules
2. Remove the tape from the speaker cable.
3. Lift the modules away.

NOTE: The modules have adhesive on the base and may require force to free.
74 Chapter 3
LCD Module Disassembly Process
configuration.
LCD Module Disassembly Flowchart
Remove LCD
Panel from Main
Unit before
proceeding
Remove
LCD Bracket
Bezel
Remove
Camera Module
Detach
Microphone
Remove Remove
LCD Brackets LCD Panel
Remove Remove
LCD FPC Cable Antennas
Screw List
Remove LCD 2*2.5 4 86.SA107.002
Brackets
Remove LCD 2*3 4 86.SA107.001
Panel
Chapter 3 75
Removing the LCD Bezel
1. See “Removing the LCD Module” on page 62.
2. Pry the bezel away from the top and then work down one side, along the bottom, then up the other side.
3. Roll the bezel up and away from the hinges.
76 Chapter 3
Removing the Camera Board
1. See “Removing the LCD Bezel” on page 76.
2. Disconnect the camera connector.
3. Pull up the camera board.
Chapter 3 77
Removing the LCD Panel
1. See “Removing the Camera Board” on page 77.
2. Pull up the microphone.
3. Remove the four screws.
Screw List
LCD Panel 2x3 4
Disassembly
78 Chapter 3
4. Lift the LCD panel out lifting the bottom of the panel first.
Chapter 3 79
Removing the LCD Brackets
1. See “Removing the LCD Panel” on page 78.
2. Remove the four LCD bracket screws.
Screw List
LCD Brackets M2*2.5 4
Disassembly
80 Chapter 3
Removing the FPC Cable
2. Place the panel face down on a clean smooth surface. Pull the microphone/camera cable off the
adhesive.
3. Lift up the protective plastic tab.
4. Disconnect the LCD connector.
Chapter 3 81
Removing the Antennas
2. Lift up the right antenna pull the cable away from the LCD module.
3. Lift up the left antenna and pull the cable away from the LCD module.
4. Pull up the two adhesive foil tabs from the cables.
82 Chapter 3
5. Remove the antennas completely.
Chapter 3 83
LCD Reassembly Procedure
NOTE: Adhesive is required to be added at various steps to cables and components. Locations of adhesive to
be added is designated with a:
NOTE: During manufacture a cyanoacrylate glue is used provided by Holdtite Adhesives LTD. This is not a
specified requirement. The reassembler is free to select an alternative appropriate adhesive.
Replacing the Antennas

1. Relay the cables around the module edge for the left antenna.
2. Relay the cables around the module edge for the right antenna.
84 Chapter 3
3. Stick the two antennas down pressing firmly.
4. Stick down the two foil tabs ensuring the screw holes are properly aligned.
Chapter 3 85
Replacing the FPC Cable
1. Connect the FPC cable connector.
2. Place the protective clear adhesive tape down firmly over the connector.
3. Apply adhesive behind the cable and stick the FPC cable down on the rear of the panel.
86 Chapter 3
Replacing the LCD Brackets
1. Replace the four screws holding the LCD brackets in place.
Screw List
LCD Brackets M2*2.5 4
Disassembly
Chapter 3 87
Replacing the LCD Panel
1. Place the LCD panel into LCD module as shown top edge first, making sure the cable is not trapped
behind the panel.
2. Replace the four screws while ensuring the cables pass through the hinges correctly.
Screw List
LCD Panel Assembly 2x3 4
88 Chapter 3
3. Apply adhesive and stick the microphone down.
Chapter 3 89
Replacing the Camera Board
1. Apply adhesive and lay the Camera Board board down pressing firmly.
2. Connect the cable to the Camera Board.
90 Chapter 3
Replacing the LCD Bezel
1. Place the bezel hinge covers over the hinges.
2. Ensure the cables are correctly exiting the hinges.
Chapter 3 91
3. Press down around the bezel starting from the bottom and working simultaneously around the edges to
the top.
92 Chapter 3
Main Unit Reassembly Process
Replacing the Speaker Modules
1. Apply adhesive in two places under the speaker modules.
2. Press down firmly on the two speaker modules.
3. Place tape over the speaker module cables.
Chapter 3 93
Replacing the RTC Battery
1. Place the RTC battery into the holding clips on the main board.
94 Chapter 3
Replacing the Thermal Module
1. Connect the thermal module connector to the main board.
2. Place the Thermal Module onto the main board. Then first tighten the three captive screws marked 1, 2, 3
on the thermal module in order: 1-2-3. First tighten Screw 1, then screw 2, then screw 3.
3
1
IMPORTANT: Incorrect order of screw replacement could harm the CPU.

3. The tighten the other two captive screws
Chapter 3 95
Replacing the CRT Board
1. Connect the CRT board cable to the main board.
2. Connect the CRT board cable to the CRT board.
3. Align the CRT board cable carefully between the main board and the CRT board and stick down the
attached tape of the cable.
96 Chapter 3
Replacing the Main Board
1. Slide the main board external connector edge in first to the lower case.
2. Replace the four screws to secure the mainboard to the lower cover.
Screw List
Main Board Assembly 2x3 4
Chapter 3 97
3. Connect the speaker connector.
98 Chapter 3
Replacing the I/O Card
1. Place the I/O card into the lower case edge first.
2. Replace the one screw.
Screw List
I/O Card Assembly 2x3 1
Chapter 3 99
3. Connect and lock the I/O card FCC to the I/O board.
4. Connect and lock the I/O card FCC to the main board.
100 Chapter 3
Replacing the Bluetooth Module
1. Connect the Bluetooth module cable to the Bluetooth module.
2. Apply adhesive and place the Bluetooth module into place pressing down firmly.
3. Connect the Bluetooth module cable to the main board.
Chapter 3 101
Replacing the LED Board
1. Connect and lock the LED board FCC to the mainboard.
2. Place the LED board into place ensuring the slide switches on the front are properly aligned in the lower
cover slots.
102 Chapter 3
Screw List
LED Board Assembly M2*3 1
4. Connect the LED board FCC to LED board.
Chapter 3 103
Replacing the LCD Module
1. Place the LCD module hinges into position on the lower case.
2. Replace the two screws.
Screw List
LCD Module Assembly M2x5 2
104 Chapter 3
3. Reconnect the LCD module connector.
4. Press the adhesive plastic tape of the LCD module connector down firmly.
Chapter 3 105
5. Relay the WLAN cables around and through the lower case.
106 Chapter 3
Replacing the Button Board
1. Put the button board to main board FCC through the upper cover and lay out correctly.
2. Apply adhesive and stick the touch pad FCC down onto the upper cover.
3. Connect the touch pad FCC to the touch pad.
Chapter 3 107
4. Place the button board onto the upper cover and replace the two screws.
Screw List
Button Board M2*3 2
Assembly
5. Connect and lock the touch pad FCC to the button board.
108 Chapter 3
6. Lay the button board FCC down carefully on the upper cover.
7. Connect the button board FCC to the button board.
Chapter 3 109
Replacing the Upper Cover
1. Place the upper cover onto the lower cover aligning the hinges first and then press down around the
edges.
2. Replace the nine screws.
110 Chapter 3
Screw List
Upper Cover M2*3 3 (blue call out)
Assembly
M2*5 6 (red call out)
3. Turn the computer over and replace the bottom cover twelve screws.
Screw List
Upper Cover M2*5 12
Assembly
4. Turn the computer back over and connect the button board FCC to the main board.
Chapter 3 111
Replacing the Keyboard
1. Connect the FCC to the mainboard.
2. Turn the keyboard over and insert the bottom edge in push down ensure the four latches across the top
are fully secured.
112 Chapter 3
Replacing the Wireless LAN Module
1. Place the wireless LAN module into its connector.
Screw List
WLAN Assembly M2*3 1
Chapter 3 113
3. Replace the connectors. The white (Aux) cable attaches to the connector marked 2 on the board. The
black (Main) cable attaches to the connector marked 1 on the board.
114 Chapter 3
Replacing the DIMM Module
1. Slide the DIMM module into the connector and press down till the locking springs click into place.
2. Place the DIMM module door down edge first.
3. Tighten the four captive screws.
Chapter 3 115
Replacing the Hard Disk Drive
DISCLAIMER: The notebook sample in the following images shows an FFC. The actual model
includes an FPC as pictured in the image on the right.
1. Connect the HDD FPC to the HDD.
2. Lift up the clear plastic tab and place the HDD into its bay.
3. Connect the HDD FPC to the main board.
NOTE: The cable pictured in the above images may differ from the actual sample.
116 Chapter 3
4. Place the HDD cover in from one edge.
5. Tighten the four captive screws.
Chapter 3 117
Replacing the Battery
1. Slide the battery into position.
2. Close the locking latch.
118 Chapter 3
Replace the Dummy Card
Push the dummy card into the slot until it clicks into place.
Chapter 3 119
120 Chapter 3
Chapter 4
Troubleshooting
Common Problems
Use the following procedure as a guide for computer problems.
NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or
modified options can give false errors and invalid system responses.
1. Obtain the failing symptoms in as much detail as possible.
2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating
the same operation.
3. Use the following table with the verified symptom to determine which page to go to.
Symptoms (Verified) Go To
Power On Issue Page 122
No Display Issue Page 123
LCD Failure Page 125
Internal Keyboard Failure Page 126
TouchPad Failure Page 127
Internal Speaker Failure Page 128
Internal Microphone Failure Page 129
USB Failure Page 131
Other Function Failure Page 131
4. If the Issue is still not resolved, see “Online Support Information” on page 165.
Chapter 4 121
Power On Issue
If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not
replace non-defective FRUs:
Start
Start
OK
Check Swap AC /Battery

AC/Battery NG to try
Power on
OK OK
Check Swap Daughter/B

Daughter/B & NG Re-plug PWR FFC
FFC Whether
OK
Swap M/B
Computer Shuts down Intermittently

If the system powers off at intervals, perform the following actions one at a time to correct the problem.
1. Check the power cable is properly connected to the computer and the electrical outlet.
2. Remove any extension cables between the computer and the outlet.
3. Remove any surge protectors between the computer and the electrical outlet. Plug the computer directly
into a known good electrical outlet.
4. Remove all external and non-essential hardware connected to the computer that are not necessary to
boot the computer to the failure point.
5. Remove any recently installed software.
122 Chapter 4
No Display Issue
If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
START
Replace LCD
Panel and No LCD Module OK?
Go to No Power
Cable
Power On ? No troubleshooting
step
Ext. DDRAM module Reconnect

No
connected properly? SDRAM Module
Ext. DDRAM Replace external

module functional? No
DDRAM module
Replace the CPU Thermal Remove and

main board
Module properly No replace thermal
connected?
module
No POST or Video
If the POST or video doesn’t display, perform the following actions one at a time to correct the problem.
1. Make sure that the internal display is selected. On this notebook model, switching between the internal
display and the external display is done by pressing Fn+F5. Reference Product pages for specific model
procedures.
2. Make sure the computer has power by checking at least one of the following occurs:
• Fans start up
• Status LEDs light up
If there is no power, see “Power On Issue” on page 122.
3. Drain any stored power by removing the power cable and battery and holding down the power button for
10 seconds. Reconnect the power and reboot the computer.
4. Connect an external monitor to the computer and switch between the internal display and the external
display is by pressing Fn+F5 (on this model).
If the POST or video appears on the external display, see “LCD Failure” on page 125.
5. Disconnect power and all external devices including port replicators or docking stations. Remove any
memory cards and CD/DVD discs. Restart the computer.
Chapter 4 123
If the computer boots correctly, add the devices one by one until the failure point is discovered.
6. Reseat the memory modules.
7. Remove the drives (see “Disassembly Process” on page 34).
Abnormal Video Display

If video displays abnormally, perform the following actions one at a time to correct the problem.
1. Reboot the computer.
2. If permanent vertical/horizontal lines or dark spots display in the same location, the LCD is faulty and
should be replaced. See “Disassembly Process” on page 34.
3. If extensive pixel damage is present (different colored spots in the same locations on the screen), the LCD
is faulty and should be replaced. See “Disassembly Process” on page 34.
4. Adjust the brightness to its highest level. See the User Manual for instructions on adjusting settings.
NOTE: Ensure that the computer is not running on battery alone as this may reduce display brightness.
If the display is too dim at the highest brightness setting, the LCD is faulty and should be replaced. See
“Disassembly Process” on page 34.
5. Check the display resolution is correctly configured:
a. Minimize or close all Windows.
b. If display size is only abnormal in an application, check the view settings and control/mouse wheel
zoom feature in the application.
c. If desktop display resolution is not normal, right-click on the desktop and select
Personalize´ Display Settings.
d. Click and drag the Resolution slider to the desired resolution.
e. Click Apply and check the display. Readjust if necessary.
6. Roll back the video driver to the previous version if updated.
7. Remove and reinstall the video driver.
8. Check the Device Manager to determine that:
• The device is properly installed. There are no red Xs or yellow exclamation marks.
• There are no device conflicts.
• No hardware is listed under Other Devices.
10. Run the Windows Memory Diagnostic from the operating system DVD and follow the onscreen prompts.
Random Loss of BIOS Settings

If the computer is experiencing intermittent loss of BIOS information, perform the following actions one at a
time to correct the problem.
1. If the computer is more than one year old, replace the CMOS battery.
2. Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3. If the computer is experiencing HDD or ODD BIOS information loss, disconnect and reconnect the power
and data cables between devices.
If the BIOS settings are still lost, replace the cables.
4. If HDD information is missing from the BIOS, the drive may be defective and should be replaced.
5. Replace the Motherboard.
124 Chapter 4
LCD Failure
If the LCD fails, perform the following actions one at a time to correct the problem. Do not replace non-
defective FRUs:
Start
OK
Check LCD Swap

module? NG LCD cable /LCD panel
OK OK
Check MB LCD Reassemble

connector and NG Re- plug LCD cable
cable ?
Swap M/B
Chapter 4 125
Built-In Keyboard Failure
If the built-in Keyboard fails, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
Start
Keyboard properly Disconnect and

No
connected? reconnect
Keyboard functioning? No Replace Keyboard
Replace
mainboard
126 Chapter 4
TouchPad Failure
If the TouchPad doesn’t work, perform the following actions one at a time to correct the problem. Do not
Start
OK
Check M/B T/P Re-assemble the

FFC NG T/P FFC to M/B
OK OK
Check Swap/Reassemble
TouchPad NG the T/P board or
T/P FFC
Swap M/B
Chapter 4 127
Internal Speaker Failure
If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace
non-defective FRUs:
Start
OK
Check M/B SPK Re-assemble the

cable NG SPK cable to M/B
OK OK
Check Logic Swap Logic

Upper/Logic NG lower/Logic upper
upper
Swap M/B
Sound Problems
If sound problems are experienced, perform the following actions one at a time to correct the problem.
1. Reboot the computer.
2. Navigate to Start´ Control Panel´ System and Maintenance´ System´ Device Manager. Check
the Device Manager to determine that:
• The device is properly installed.
• There are no red Xs or yellow exclamation marks.
• There are no device conflicts.
• No hardware is listed under Other Devices.
3. Roll back the audio driver to the previous version, if updated recently.
4. Remove and reinstall the audio driver.
5. Ensure that all volume controls are set mid range:
a. Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted.
b. Click Mixer to verify that other audio applications are set to 50 and not muted.
6. Navigate to Start´ Control Panel´ Hardware and Sound´ Sound. Ensure that Speakers are selected
as the default audio device (green check mark).
NOTE: If Speakers does not show, right-click on the Playback tab and select Show Disabled Devices
(clear by default).
7. Select Speakers and click Configure to start Speaker Setup. Follow the onscreen prompts to configure
the speakers.
128 Chapter 4
8. Remove and recently installed hardware or software.
9. Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
10. Reinstall the Operating System.
Internal Microphone Failure

If the internal Microphone fails, perform the following actions one at a time to correct the problem. Do not
Start
OK
Check M/B Mic. Re-assemble the

cable NG MIC cable to M/B
OK OK
Check MIC wire Swap MIC wire of

of LCD module NG LCD module
Swap M/B
Microphone Problems
If internal or external Microphones do no operate correctly, perform the following actions one at a time to
correct the problem.
1. Check that the microphone is enabled. Navigate to Start´ Control Panel´ Hardware and Sound´
Sound and select the Recording tab.
2. Right-click on the Recording tab and select Show Disabled Devices (clear by default).
3. The microphone appears on the Recording tab.
4. Right-click on the microphone and select Enable.
5. Select the microphone then click Properties. Select the Levels tab.
6. Increase the volume to the maximum setting and click OK.
7. Test the microphone hardware:
a. Select the microphone and click Configure.
b. Select Set up microphone.
Chapter 4 129
c. Select the microphone type from the list and click Next.
d. Follow the onscreen prompts to complete the test.
HDD Not Operating Correctly

If the HDD does not operate correctly, perform the following actions one at a time to correct the problem.
1. Disconnect all external devices.
2. Run a complete virus scan using up-to-date software to ensure the computer is virus free.
3. Run the Windows Vista Startup Repair Utility:
a. insert the Windows Vista Operating System DVD in the ODD and restart the computer.
b. When prompted, press any key to start to the operating system DVD.
c. The Install Windows screen displays. Click Next.
d. Select Repair your computer.
e. The System Recovery Options screen displays. Click Next.
f. Select the appropriate operating system, and click Next.
NOTE: Click Load Drivers if controller drives are required.
g. Select Startup Repair.
h. Startup Repair attempts to locate and resolve issues with the computer.
i. When complete, click Finish.
If an issue is discovered, follow the onscreen information to resolve the problem.
4. Run the Windows Memory Diagnostic Tool. For more information see Windows Help and Support.
5. Restart the computer and press F2 to enter the BIOS Utility. Check the BIOS settings are correct and that
CD/DVD drive is set as the first boot device on the Boot menu.
6. Ensure all cables and jumpers on the HDD and ODD are set correctly.
7. Remove any recently added hardware and associated software.
8. Run the Windows Disk Defragmenter. For more information see Windows Help and Support.
9. Run Windows Check Disk by entering chkdsk /r from a command prompt. For more information see
Windows Help and Support.
10. Restore system and file settings from a known good date using System Restore.
If the issue is not fixed, repeat the preceding steps and select an earlier time and date.
11. Replace the HDD. See “Disassembly Process” on page 34.
130 Chapter 4
USB Failure (Right up/down side)
If the rightside USB port fails, perform the following actions one at a time to correct the problem. Do not
Start
OK
Check USB/B to Re-assemble the

M/B cable NG USB/B cable to M/B
OK OK
Swap USB/B and

Check USB/B NG USB cable
Swap M/B
Other Failures
If the VGA board, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or Volume
Wheel fail, perform the following general steps to correct the problem. Do not replace non-defective FRUs:
1. Check whether the drive is OK.
2. Verify that the Test Fixture is ok.
3. Swap the mainboard and retest.
Chapter 4 131
Intermittent Problems
Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a
hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement
should be considered only when a recurring problem exists.
When analyzing an intermittent problem, do the following:
1. Run the advanced diagnostic test for the system board in loop mode at least 10 times.
2. If no error is detected, do not replace any FRU.
3. If any error is detected, replace the FRU. Rerun the test to verify that there are no more errors.
Undetermined Problems
The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect,
whether a short circuit is suspected, or whether the system is inoperative.
Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU).
NOTE: Verify that all attached devices are supported by the computer.
NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power On
Issue” on page 122.):
1. Power-off the computer.
2. Visually check them for damage. If any problems are found, replace the FRU.
3. Remove or disconnect all of the following devices:
• Non-Acer devices
• Printer, mouse, and other external devices
• Battery pack
• Hard disk drive
• DIMM
• CD-ROM/Diskette drive Module
• PC Cards
4. Power-on the computer.
5. Determine if the problem has changed.
6. If the problem does not recur, reconnect the removed devices one at a time until you find the failing FRU.
7. If the problem remains, replace the following FRU one at a time. Do not replace a non-defective FRU:
• System board
• LCD assembly
132 Chapter 4
POST Code Reference Tables
These tables describe the POST codes and components of the POST process.
POST Routine Description Code

PeiEventLog 01
OemServices 02
SioInit 03
MonoStatusCode 04
PentiumMCpuPeim 08
PlatformStage1 09
Variable 0A
IchInit 0B
PlatformStage2 0D
IchSmbusArpDisabled 0E
ClockGen 12
OpPresence 13
TcgPei 14
FindFv 15
DxeIpl 2F
LightMemoryInit 10
S3ResumeSoftSmi 11
Crc32SectionExtract 31
OemServices A4
EventLog A5
ScriptSave 32
AcpiS3Save 33
SmartTimer 34
JpegDecoder 35
PcxDecoder 36
PlatformBds 8A
MpCpu 37
LegacyMetronome 38
FtwLite 39
Runtime 3A
MonotonicCounter 3B
WatchDogTimer 3C
SecurityStub 3D
CpuIo 3E
Cf9Reset 3F
PcRtc 40
StatusCode 41
Variable 42
SmmVariable CF
EmuVariable 43
Chapter 4 133
TcgDxe A2
PhysicalPresence A3
TpmDriver AE
TcgSmm AE
PhysicalPresenceReadyToBoot AE
DataHubRecordPolicy AD
Undi 86
SNP 90
BC 91
PxeDhcp4 92
Ebc 93
IsaBus 4D
IsaSerial 4E
Ps2Mouse 6D
IdeBus 4F
LightPciBus 50
UsbBot 6E
UsbCbi0 6F
UsbCbi1 70
UsbKb 71
UsbMassStorage 72
UsbMouse 74
Ehci 8F
Uhci 73
UsbBus 75
SmmBase C2
SmmDisp C5
SmmReloc C4
SmmRuntime C7
SmmThunk C9
OemServices D8
ChipsetInit 44
SmmAccess C0
PciHostBridge 46
PciExpress 47
GmchMbi CD
IchInit 48
IdeController 49
SataController 4A
IchSmbusLight 4B
SmmControl C1
Ich7MSmmDispatcher C8
IsaAcpiDriver 4C
134 Chapter 4
Fwh 52
SmmFwh CE
PciHotPlug 54
BootOptionPolicy 51
SetupUtility 76
Platform 55
PlatformIde 56
Ppm D9
Platform CC
Ihisi D0
SetupMouse f9
Int15Microcode D1
SmmPnp D2
Smbios 57
MemorySubClass 58
MiscSubclassDriver 59
SysPassword AB
PswdConsole AC
HddPswdServiceBody D7
HddPswdService A6
HiiDatabase 80
OemSetupBrowser 82
Font(English) 7E
Font(French) 7F
Font( Chinese ) 8D
UnicodeCollation B1
ConPlatform 5A
ConSplitter 5D
GraphicsConsole 79
Terminal 7A
VgaClass 5E
SaveMemoryConfig 5B
AcpiSupport 5C
AcpiPlatform 53
DataHub 5F
DataHubStdErr 7B
GenericMemoryTest 61
DiskIo 60
Fat 7C
Partition 7D
PciPlatform 6B
AlertStandardForma 45
PciSerial A8
Chapter 4 135
AsfInit A7
IdeRController A9
Legacy8259 63
LegacyRegion 64
LegacyInterrupt 65
BiosKeyboard 66
BiosVideo 67
MonitorKey 68
LegacyBios 69
LegacyBiosPlatform 6A
LegacyMouse 77
SmmUsbLegacy 78
AmtbxInvoke AA
OemBadgingSupport 83
136 Chapter 4
Chapter 5
Jumper and Connector Locations
Mainboard Top View
TOP SIDE PJ2: Battery connector

CN3: LCD connector
PJ1: DC-in
JSIM2: SIM card connector
U12: EC Winbond
WPCE775LA0DG
CN4: Keyboard connector
CN5: Touch Pad connector

CN18: HDMI
U2: HDMI level shift U14: Codec
Realtek ALC269X
CN8: Card Reader board Connector

CN17: USB
CN7: Speaker Connector
U9: Clock Generator
CN2: LED board
connector CN6: Bule Tooth Connector
Item Description Item Description

PJ1 DC-in CN6 Bluetooth Connector
CN3 LCD connector U9 Clock Generator
JSIM2 SIM card connector CN2 LED board connector
PJ2 Battery connector CN17 USB connector
U12 EC Winbond CN18 HDMI
U14 Codec U2 HDMI level shift
CN8 Card reader board connector CN4 Keyboard connector
CN7 Speaker Connector CN5 Touch Pad connector
Chapter 5 137
Mainboard Bottom View
BOTTOM SIDE CN15: CRT board connector
CN12: DDR2 DIMM1

CN10: DDR2 DIMM2
U18: CPU
CN9: HDD
connector
U17: NB GS45
CN16: FAN
CN14: RTC
CN11: Mini Card CN13: Mini Card
U19: SB ICH9M
For WLAN For 3G card
Item Description Item Description

CN10 DDR2 DIMM2 CN14 RTC
CN12 DDR2 DIMM1 U19 SB ICH9M
U18 CPU CN13 Mini Card
U17 NB GS45 CN11 Mini Card (WLAN)
CN16 Fan CN9 HDD
138 Chapter 5
Clearing Password Check and BIOS Recovery
This section provides a procedure for clearing the password and BIOS. The Hardware Open Gap on the main
board clears the CMOS of all user settings and restores factory defaults.
Mainboard CMOS Discharge

Discharging the CMOS clears all user settings.
1. Disassemble the notebook and take out the Mainboard. See “Removing the Mainboard” on page 69.
2. Remove the RTC battery. See “Removing the RTC Battery” on page 73.
3. Turn the mainboard over and short the G2 pad.
4. Reconnect the RTC battery and reassemble the unit.
Chapter 5 139
BIOS Recovery by Crisis Disk
BIOS Recovery Boot Block

The BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS
initialization. Users can enable this feature to restore the BIOS firmware to the factory settings if a BIOS flash
process fails.
BIOS Recovery Hotkey

The system provides a function hotkey: Fn+Esc, to enable the BIOS Recovery process when a system is
powered on during BIOS POST. To use this function, it is strongly recommended to have the AC adapter and
Battery present. If this function is enabled, the system will force the BIOS to enter a special BIOS block, called
Boot Block.
Steps for BIOS Recovery from USB Storage

Before performing this procedure, prepare a Crisis USB key. The Crisis USB key can be made by executing
the Crisis Disk program in a functioning system with a Windows XP or Vista OS.
IMPORTANT:The Crisis Disk program will overwrite all data on any drive that you use as a crisis disk.
Follow the steps below:
1. Modify the archive name from "zh7 bios" to "ZH7X64.fd"
2. Save ROM file (file name: ZH7X64.fd ) to the root directory of the USB storage.
3. Plug the USB storage into a USB port.
4. Press Fn + ESC button then plug in AC.
The Power button flashes once.
5. Press Power button to initiate system CRISIS mode.
When CRISIS is complete, the system auto restarts with a workable BIOS.
6. Update the latest version BIOS for this machine by the regular BIOS flashing process.
140 Chapter 5
Chapter 6
FRU (Field Replaceable Unit) List

This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of the computer. Refer to this
chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization).
Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your
regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service
Guide. For ACER AUTHORIZED SERVICE PROVIDERS, your Acer office may have a DIFFERENT part number code from
those given in the FRU list of this printed Service Guide. You MUST use the local FRU list provided by your regional Acer
office to order FRU parts for repair and service of customer machines.
NOTE: To scrap or to return the defective parts, you should follow the local government ordinance or regulations on how to
dispose it properly, or follow the rules set by your regional Acer office on how to return it.
Packard Bell dot Exploded Diagrams
Chapter 6 141
Main Assembly
Item Description Part Number

1 K/B KB.I110G.026*
2 Top Sub Assy 60.WF807.001
3 Bluetooth Cable Assy 50.SA107.001
4 FCC LED Cable 50.SA107.001
5 CRT Board Assy 50.SA107.001
142 Chapter 6
6 LED Board Assy 55.WF807.001
7 CRT Cable Assy 55.WF807.001
8 Main Board MB.SA506.001*
9 Thermal Module UMA Assy 60.SA107.006
10 Base Sub Assy 60.WF807.002
11 RAM KN.2GB03.011*
12 RAM Door Assy 42.WF807.001
13 Touch Pad Board Assy 55.WF807.004
14 Bluetooth Module BH.21100.004
15 Cardreader Cable FCC 50.SA107.003
16 Battery BT.00607.106*
17 LAN Board Assy 55.WF807.003
18 SD Dummy Card 42.WF807.003
19 HDD KH.16001.042*
20 HDD Mylar TBD
21 Cable FPC HDD 50.SA107.006
22 WLAN Card NI.23600.046*
23 Rubber Base 47.WF807.002
24 HDD Door Assy 42.WF807.002
NOTE: Part numbers may be different depending on your model. Please refer to the FRU List for a full listing
of part numbers.
Chapter 6 143
LCD Assembly

1 LCD Bezel 60.BD807.003
2 LCD Cover 60.BD807.001*
3 LCD Bracket-R 60.BD807.003
4 LCD Bracket-L 33.WF807.001
5 LCD Panel LK.11605.001*
6 Camera 57.S6507.002*
7 LCD Cable w/Microphone 50.SA107.005
NOTE: Part numbers may be different depending on your model. Please refer to the FRU List for a full listing
of part numbers.
144 Chapter 6
FRU List
CATEGORY PARTNAME ACER P/N.
ADAPTER
ADAPTER DELTA 30W 19V 1.7X5.5X11 BLACK ADP- AP.03001.001
30JH BA LF
ADAPTER LITE-ON 30W 1.7X5.5X11 BLACK PA-1300- AP.03003.001
04AC LF
ADAPTER HIPRO 30W 19V 1.7X5.5X11 BLACK HP- AP.0300A.001
A0301R3 B1LF LF
BATTERY
Battery SIMPLO UM-2009E Li-Ion 3S2P PANASONIC 6 BT.00607.106
cell 4400mAh Main COMMON ID:UM09E71
Battery SIMPLO UM-2009E Li-Ion 3S2P SAMSUNG 6 BT.00607.107
Battery SANYO UM-2009E Li-Ion 3S2P SANYO 6 cell BT.00603.096
5600mAh Main COMMON ID:UM09E36
Battery SIMPLO UM-2009E Li-Ion 3S2P SAMSUNG 6 BT.00607.102
Battery SIMPLO UM-2009E Li-Ion 3S2P LGC 6 cell BT.00607.103
BOARD
Foxconn Wireless LAN Atheros HB93 1x2 BGN (HM) NI.23600.046
Lan Intel WLAN 512AG_HMWG Shirley Peak 5100 KI.SPH01.005
MM#897072
Lan Intel WLAN 512AN_HMWG Shirley Peak 5100 KI.SPH01.003
MM#895373
Liteon Wireless LAN Atheris HB93 1x2 BGN (HM) NI.23600.051
WN6602AH
Foxconn Bluetooth FOX BRM 2046 BT2.1 BH.21100.004
LED BOARD 55.WF807.001
CRT BOARD 50.SA107.001
LAN BOARD 55.WF807.003
TP BOARD 55.WF807.004
CCD
Chapter 6 145
Suyin Camera Rosa 2G, MODULE CN0316-S30C- 57.S6507.001
OV06-1
CAMERA CNF9011(CMOS,0.3M,VGA) 57.S6507.002
CABLE
POWER CORD US 3PIN ROHS 27.TAXV7.001
POWER CORD(EU) 1.8M 3PBLACK FM010008-010 27.TATV7.001
POWER CORD AU W/LABEL (3 PIN) 27.A50V7.003
POWER CORD PRC 3P Y536B30001218008 27.TATV7.004
POWER CORD UK 3PIN 27.A03V7.004
POWER CORD US-110V (BSMI) 27.A99V7.002
POWER CORD SWISS 3 PIN 27.A99V7.004
PWR CORD(ISR)1.8M 3PBLK FZ0I0008-038 27.TATV7.005
POWER CORD ITALIAN 3PIN 27.A99V7.005
POWER CORD(S.A) 1.8M 3BLACK FZ010008-006 27.T48V7.001
PWR CORD V943B30001218008 DANISH 3P 27.A03V7.006
PWR CORD V943B30001218008 DANISH 3P 27.A03V7.006
POWER CORD AF-S (INDIA) 27.A50V7.001
POWER CORD ARGENTINE 3 PIN BLACK 27.S0207.001
POWER CORD JAPANESE 27.TAXV7.003
POWER CORD BRAZIL IMETRO 3 PIN 27.S0607.001
BLUETOOTH CABLE 50.SA107.001
CRT CABLE 55.WF807.001
FFC CABLE - CARD READER/B TO MB 50.SA107.003
FFC CABLE - LED/B TO MB 50.SA107.001
LCD CABLE W/MIC FOR CCD 50.SA107.005
FPC CABLE - HDD TO MB 50.SA107.006
146 Chapter 6
CASE/COVER/BRACKET
ASSEMBLY
UPPER CASE ASSY BLACK W/TP, FFC CABLE *2 60.WF807.001
UPPER CASE ASSY RED W/TP, FFC CABLE *2 60.WFA07.001
LOWER CASE ASSY W/SPEAKER FOR 3G 60.WF707.001

LOWER CASE ASSY W/SPEAKER FOR NON 3G 60.WF807.002
HDD COVER BLACK 42.WF807.002
RAM COVER BLACK 42.WF807.001
LCD COVER ASSY PB BLACK W/ANTENNA *2 60.BD807.001

LCD COVER ASSY PB BLACK W/ANTENNA *3 60.BD807.002
LCD COVER ASSY PB RED W/ANTENNA *2 60.BD607.001
LCD COVER ASSY PB RED W/ANTENNA *3 60.BD607.002
LCD BEZEL ASSY PB BLACK 60.BD807.003
LCD BRACKET W/HINGE R 60.BD807.003
LCD BRACKET W/HINGE L 33.WF807.001
SD DUMMY CARD BLACK 42.WF807.003
Chapter 6 147
SATA HDD/HARD DISK DRIVE
HDD SEAGATE 2.5" 5400rpm 160GB ST9160314AS KH.16001.042
Wyatt SATA LF F/W:0001SDM1
HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX Libra KH.16004.006
SATA LF F/W: FG011J
HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300 KH.16007.026
Panther B SATA LF F/W:C60F Disk imbalance criteria =
0.014g-cm
SATA LF F/W:FG001J
HDD HGST 2.5" 5400rpm 250GB HTS545025B9A300 KH.25007.016
Panther B SATA LF F/W:C60F Disk imbalance criteria =
0.014g-cm
SATA LF F/W:FG011J
SATA LF F/W:FG001J
HDD WD 2.5" 5400rpm 500GB WD5000BEVT-22ZAT0 KH.50008.013
ML250 SATA LF F/W:01.01A01
KEYBOARD
Keyboard GATEWAY GP1T SJM11 86KS Black Arabic KB.I110G.002
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black Belgium KB.I110G.003
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black Brazilian KB.I110G.004
Portuguese Texture
Keyboard GATEWAY GP1T SJM11 87KS Black CZ/SK KB.I110G.005
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black Danish KB.I110G.007
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black FR/ KB.I110G.008
Arabic Texture
Keyboard GATEWAY GP1T SJM11 87KS Black French KB.I110G.009
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black German KB.I110G.010
Texture
Keyboard GATEWAY GP1T SJM11 86KS Black Greek KB.I110G.011
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black KB.I110G.012
Hungarian Texture
148 Chapter 6
Keyboard GATEWAY GP1T SJM11 87KS Black Italian KB.I110G.013
Texture
Japanese Texture
Keyboard GATEWAY GP1T SJM11 87KS Black Nordic KB.I110G.015
Texture
Norwegian Texture
Portuguese Texture
Keyboard GATEWAY GP1T SJM11 86KS Black Russian KB.I110G.018
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black SLO/ KB.I110G.019
CRO Texture
Keyboard GATEWAY GP1T SJM11 87KS Black Spanish KB.I110G.020
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black Sweden KB.I110G.021
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black Swiss/G KB.I110G.022
Texture
Keyboard GATEWAY GP1T SJM11 86KS Black Thailand KB.I110G.023
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black Turkish KB.I110G.024
Texture
Keyboard GATEWAY GP1T SJM11 87KS Black UK KB.I110G.025
Texture
Keyboard GATEWAY GP1T SJM11 86KS Black Chinese KB.I110G.006
Texture
Keyboard GATEWAY GP1T SJM11 86KS Black US KB.I110G.026
International Texture
Keyboard GATEWAY GP1T SJM11 86KS Black US KB.I110G.027
International w/ Hebrew Texture
Keyboard GATEWAY GP1T SJM11 87KS Black US w/ KB.I110G.028
Canadian French Texture
LCD
LED LCD AUO 11.6" WXGA Glare B116XW02 V0 LF LK.11605.001
200nit 8ms 500:1
LED LCD CMO 11.6" WXGA Glare N116B6-L02 LF LK.1160D.001
200nit 10ms 500:1
LED LCD SAMSUNG 11.6" WXGA Glare LTN116AT01- LK.11606.001
A01 LF 200nit 8ms
LED LCD LPL 11.6" WXGA Glare LP116WH1-TLA1 LF LK.11608.001
200nit 8ms 500:1
LED LCD AUO 11.6" WXGA Glare B116XW02 V0 1A LK.11605.003
(3G) LF 200nit 8ms 500:1
MAINBOARD
Chapter 6 149
MAINBOARD GS45 ICH9M CPU SU3500B W/O RAM MB.SA506.001
FOR 3G
MAINBOARD GS45 ICH9M CPU SU3500B W/O RAM MB.SA106.001
FOR NON 3G
MAINBOARD GS45 ICH9M CPU CM723B W/O RAM MB.SAA06.00
FOR 3G 1
MAINBOARD GS45 ICH9M CPU CM723B W/O RAM MB.SA706.001
FOR NON 3G
MAINBOARD GS45 ICH9M CPU SU2700B W/O RAM MB.PJ306.003
FOR 3G
FOR NON 3G
FOR 3G
MEMORY
Memory SAMSUNG SO-DIMM DDRII 667 2GB KN.2GB0B.00
M470T5663QZ3-CE6 LF 3
Memory NANYA SO-DIMM DDRII 667 2GB KN.2GB03.011
NT2GT64U8HD0BN-3C LF 128*8 0.07um
Memory SAMSUNG SO-DIMM DDRII 667 2GB KN.2GB0B.01
M470T5663EH3-CE6 LF 128*8 0.055um 1
Memory HYNIX SO-DIMM DDRII 667 2GB KN.2GB0G.00
HYMP125S64CP8-Y5 LF 4
Heatsink
THERMAL MODULE UMA 60.SA107.006
MISCELLANEOUS
LOWER CASE SCREW RUBBER 47.WF807.001
UPPER CASE RUBBER 47.WF807.002
LOWER CASE RUBBER FOOT - FRONT (LONG) 47.WF807.003
LOWER CASE RUBBER FOOT - REAR 47.WF807.004
LCD BEZEL RUBBER 47.WF807.005
Screw List
PARTNAME ACER P/N
SCREW M2*3.0 I (BNI,NYLOK)IRON 86.WF807.001
SCREW M2*5-I(BZN)(NYLOK) 86.TG607.004
SCREW M2.0*2.5-I (BNI,NYLOK)IRON 86.W0907.005
SCREW M3.0*3.5-I(NI)(NYLOK)STEEL 86.WF807.002
150 Chapter 6
Appendix A
Model Definition and Configuration
Model RO Acer Part No Description

DOTMU- EMEA LU.BCV0X.001 DOTMU-721G16n VHP32DTFR1 UMACkk4 1*1G/
721G16n 160/6L2.2/5R/CB_bgn_0.3D_GEk_FR51 DOT_M/
U.FR/010
DOTMU- EMEA LU.BD80Y.001 DOTMU-353G16n VHB32DTNL1 UMACkk8 2G+1G/
353G16n 160/6L2.8/5R/CB_n2_0.3D_BAG_GEk_NL31
DOT_M/U.NL/300
DOTMU- EMEA LU.BD80X.004 DOTMU-352G25n VHP32DTFR1 UMACkk8 2*1G/
352G25n 250/6L2.8/5R/CB_n2_0.3D_GEk_FR51 DOT_M/
U.FR/020
DOTMU- EMEA LU.BD80X.003 DOTMU-354G32n VHP32DTES1 UMACkk8 2*2G/
354G32n 320/BT/6L2.8/5R/CB_n2_0.3D_BAG_GEk_ES31
DOT_M/U.SP/001
DOTMU- EMEA LU.BD80X.002 DOTMU-354G32n VHP32DTND1 UMACkk8 2*2G/
354G32n 320/6L2.8/5R/CB_n2_0.3D_GEk_ENU1 DOT_M/
U.NC/860
DOTMU- EMEA LU.BD80X.001 DOTMU-354G32n VHP32DTFR1 UMACkk8 2*2G/
354G32n 320/6L2.8/5R/CB_n2_0.3D_GEk_FR51 DOT_M/
U.FR/021
VGA
Model CPU LCD Memory 1 HDD 1(GB)
Chip
DOTMU- CM723B NLED11.6WXGAG UMA SO1GBII6 N160GB5.4KS
721G16n
DOTMU- C2SSU3500B NLED11.6WXGAG UMA SO2GBII6 N160GB5.4KS
353G16n
352G25n
354G32n
354G32n
354G32n
Extra Blue
Model Card Reader Wireless LAN Wireless LAN1 Battery
SW1 tooth
DOTMU- NIS 5 in 1-Build in 3rd WiFi 1x2 3rd WiFi 1x2 N 6CELL2.2
721G16n BGN BGN
DOTMU- NIS 5 in 1-Build in SP1x2HMW SP1x2HMW N 6CELL2.8
353G16n
352G25n
DOTMU- NIS 5 in 1-Build in SP1x2HMW SP1x2HMW BT 6CELL2.8
354G32n 2.1
Appendix A 151
Extra Blue
Model Card Reader Wireless LAN Wireless LAN1 Battery
SW1 tooth
354G32n
354G32n
152 Appendix A
Appendix B
Test Compatible Components

This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system
functions are tested under Windows® XP Home, Windows® XP Pro environment.
Refer to the following lists for components, adapter cards, and peripherals which have passed these tests.
Regarding configuration, combination and test procedures, please refer to the Compatibility Test Report
released by the Acer Mobile System Testing Department.
BRAND Type Description

3G
Qualcomm Gobi2000 Qualcomm Gobi2000
A cover
Black IMR Black IMR
Red IMR Red IMR
Accessory
PackardBell PackardBell 11inch PackardBell Accessory PackardBell 11" Netbook Bag
Netbook Bag black Black
Adapter
DELTA 30W Adapter DELTA 30W 19V 1.7x5.5x11 Black ADP-30JH
BA LF
HIPRO 30W Adapter HIPRO 30W 19V 1.7x5.5x11 Black HP-
A0301R3 B1LF LF
LITE-ON 30W Adapter LITE-ON 30W 19V 1.7x5.5x11 Black PA-
1300-04AC LF
Audio Codec
Realtek ALC269X Realtek Audio Codec ALC269X
B cover
Mirror w/Camera Mirror w/Camera
Battery
PANASONIC 6CELL2.2 Battery PANASONIC UM-2009E Li-Ion 3S2P
PANASONIC 6 cell 4400mAh Main COMMON
ID:UM09E51
SANYO 6CELL2.2 Battery SANYO UM-2009E Li-Ion 3S2P SANYO 6 cell
4400mAh Main COMMON ID: UM09E31
SANYO 6CELL2.8 Battery SANYO UM-2009E Li-Ion 3S2P SANYO 6 cell
SIMPLO 6CELL2.2 Battery SIMPLO UM-2009E Li-Ion 3S2P PANASONIC
6 cell 4400mAh Main COMMON ID:UM09E71
SIMPLO 6CELL2.2 Battery SIMPLO UM-2009E Li-Ion 3S2P PANASONIC
6 cell 4400mAh Main COMMON ID:UM09E71
SIMPLO 6CELL2.8 Battery SIMPLO UM-2009E Li-Ion 3S2P SAMSUNG 6
SIMPLO 6CELL2.8 Battery SIMPLO UM-2009E Li-Ion 3S2P SAMSUNG 6
Bluetooth
Appendix B 153
Foxconn BT 2.1 Foxconn Bluetooth BRM 2046 BT2.1 (T60H928.33) f/
w:861
Camera
Chicony 0.3M LDV Chicony Camera Lilac_2G
Suyin 0.3M LDV Suyin Camera Rose_2G
Card Reader
5 in 1-Build in 5 in 1-Build in MS, MS Pro, SD, SC, XD
INTEL C2SSU3500B CPU Intel Core2Solo SU3500 BGA 1.4G 3M 800
5.5W ULV
INTEL CM723B CPU Intel Celeron 723 BGA 1.2G 1M 800 10W R-0
ULV
HDD
HGST N160GB5.4KS HDD HGST 2.5" 5400rpm 160GB Falcon B
HTS543216L9SA00 SATA LF F/W:C40C
HGST N160GB5.4KS HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300
Panther B SATA LF F/W:C60F Disk imbalance criteria
= 0.014g-cm
= 0.014g-cm
= 0.014g-cm
= 0.014g-cm
SEAGATE N160GB5.4KS HDD SEAGATE 2.5" 5400rpm 160GB ST9160314AS
TOSHIBA N160GB5.4KS HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX
Libra SATA LF F/W: FG011J
Libra SATA LF F/W:FG001J
Libra SATA LF F/W:FG011J
WD N160GB5.4KS HDD WD 2.5" 5400rpm 160GB WD1600BEVT-
22ZCTO ML160 SATA LF F/W:11.01A11
22ZCT0 ML160 SATA LF F/W:11.01A11
22ZCT0 ML160 SATA LF F/W:11.01A11
Keyboard
ACER NT1T Keyboard ACER NT-1T JV11 Internal 11 Standard
Black NONE Texture
LAN
Atheros AR8131L Atheros AR8131L
154 Appendix B
LCD
AUO NLED11.6WXGAG LED LCD AUO 11.6" WXGA Glare B116XW02 V0 LF
200nit 8ms 500:1
AUO NLED11.6WXGAG LED LCD AUO 11.6" WXGA Glare B116XW02 V0 2A
LF 200nit 8ms 500:1
AUO NLED11.6WXGAG LED LCD AUO 11.6" WXGA Glare B116XW02 V0 1A
(3G) LF 200nit 8ms 500:1
CMO NLED11.6WXGAG LED LCD CMO 11.6" WXGA Glare N116B6-L02 C2
LF 200nit 10ms 500:1
LPL NLED11.6WXGAG LED LCD LPL 11.6" WXGA Glare LP116WH1-TLA1
LF 200nit 8ms 500:1
SAMSUNG NLED11.6WXGAG LED LCD SAMSUNG 11.6" WXGA Glare
LTN116AT01-A01 LF 200nit 8ms
MEM
HYNIX SO1GBII6 Memory HYNIX SO-DIMM DDRII 667 1GB
HYMP112S64CP6-Y5 LF
HYNIX SO2GBII6 Memory HYNIX SO-DIMM DDRII 667 2GB
HYMP125S64CP8-Y5 LF
NANYA SO1GBII6 Memory NANYA SO-DIMM DDRII 667 1GB
NT1GT64UH8D0FN-3C LF 64*16 0.07um
NANYA SO2GBII6 Memory NANYA SO-DIMM DDRII 667 2GB
NT2GT64U8HD0BN-3C LF 128*8 0.07um
SAMSUNG SO1GBII6 Memory SAMSUNG SO-DIMM DDRII 667 1GB
M470T2864QZ3-CE6 LF
M470T2864QZ3-CE6 LF
M470T5663QZ3-CE6 LF
M470T5663QZ3-CE6 LF
NB Chipset
INTEL GS45 NB Chipset Intel CS GS45NB
SB Chipset
INTEL ICH9M-SFFE SB Chipset Intel CS AM82801IUX MM#898134
Software
NIS Antivirus application NIS
Appendix B 155
156 Appendix B
Appendix C
Online Support Information

This section describes online technical support services available to help you repair your Acer Systems.
If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch
office. Acer Branch Offices and Regional Business Units may access our website. However some information
sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
Acer's Website offers you convenient and valuable support resources whenever you need them.
In the Technical Information section you can download information on all of Acer's Notebook, Desktop and
Server models including:
• Service guides for all models
• User's manuals
• Training materials
• Bios updates
• Software utilities
• Spare parts lists
• TABs (Technical Announcement Bulletin)
For these purposes, we have included an Acrobat File to facilitate the problem-free downloading of our
technical material.
Also contained on this website are:
• Detailed information on Acer's International Traveler's Warranty (ITW)
• Returned material authorization procedures
• An overview of all the support services we offer, accompanied by a list of telephone, fax and email
contacts for all your technical queries.
We are always looking for ways to optimize and improve our services, so if you have any suggestions or
comments, please do not hesitate to communicate these to us.
Appendix C 157
158
Index
A Flowchart 44
Antennas F
Removing 82, 84
Features 1
B FLASH Utility 33
Battery Pack Flash Utility 33

Removing 45 FRU (Field Replaceable Unit) List 141
BIOS
ROM type 19
H
vendor 19 Hard Disk Drive Module
Version 19
Removing 47
BIOS Utility 25–33 Hibernation mode
Advanced 28 hotkey 13
Boot 31
Hot Keys 11
Exit 32
Navigating 25 I
Power 31
Save and Exit 32 Indicators 9
Security 28
System Security 32 Intermittent Problems 132
brightness Internal Microphone Failure 129

hotkeys 13 Internal Speaker Failure 128
Button Board
Removing 59
J
C Jumper and Connector Locations 137
Camera Board K
Removing 77, 90 Keyboard
caps lock Removing 55
on indicator 9
Keyboard Failure 126
Common Problems 122
CRT Cable L
Removing 69 LCD Bezel
D Removing 76, 91
LCD Brackets
DIMM Module Removing 81
Removing 49 LCD Cable
Display 4 Removing 81
display LCD Failure 125
hotkeys 13 LCD Module
E Removing 104
LCD Module Disassembly
Euro Key 14 Flowchart 75
External Module Disassembly LCD Panel
159
Removing 78, 88 LCD Failure 125
No Display 123
M ODD 131
Other Failures 131
Main Unit Disassembly
Power On 122
Flowchart 53 Touch Pad 127
Mainboard USB 131
Removing 69
media access
U
on indicator 9 Undetermined Problems 132
Memory Check 122 Upper Cover
Microphone Removing 57
Removing 78, 88 USB Failure (Rightside) 131
Model Definition 151 utility
BIOS 25–33
N
V
No Display Issue 123
num lock volume
on indicator 9 hotkeys 13
O W
ODD Failure 131 Windows 2000 Environment Test 153
WLAN Board
Online Support Information 157
Removing 51
P
Panel 5
PC Card 9
Power On Failure 122
S
Speaker Module
Removing 66
speakers
hotkey 13
System
Block Diagram 4
T
Test Compatible Components 153
Thermal Module
Removing 72
Touch Pad Failure 127
Troubleshooting
Built-in KB Failure 126
Internal Microphone 129
Internal Speakers 128
160
161
162

27 Service Manual - Packard Bell - Dot Mr-U MR

Uploaded by

Copyright:

Available Formats

27 Service Manual - Packard Bell - Dot Mr-U MR

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

27 Service Manual - Packard Bell - Dot Mr-U MR

Uploaded by

Copyright:

Available Formats

www.SoporteTecnicoBsAs.com.

Repuestos para tus equipos.

Envios a Todo el Pais

Service guide files and updates are available

Display and graphics

Dimensions and Weight)

Icon Item Description

Icon Item Description

Num Lock Lights up when the Num Lock is activated.

Caps Lock Lights up when the Caps Lock is activated.

Keyboard For entering data into your computer

Battery Indicates the computer’s battery status.

Communication Indicates the status of WLAN/3G communication.

Closed Front View

Bluetooth Wireless LAN/3G Speakers

Icon Item Description

Monitor Power Ventilation HDMI out USB

Icon Item Description

DC-in jack Connects to an AC adapter.

Memory card Headphone Microphone USB port Kensington Ethernet

Icon Item Description

Headphones/ Connects to audio line-out devices (e.g., speakers, headphones).

Kensington lock Connects to a Kensington-compatible computer security lock.

Icon Item Description

Memory Houses the computer’s main memory.

Icon Item Description

Icon Function Description

Battery Indicates the computer's battery status.

Bluetooth Indicates the status of Bluetooth communication.

Wireless LAN Indicates the status of Wireless LAN communication.

HDD Indicates when the hard disk drive is active.

Num Lock Lights up when Num Lock is activated.

Caps Lock Lights up when Caps Lock is activated.

Lock Keys and embedded numeric keypad

Lock key Description

Hotkey Icon Function Description

The Euro symbol

The US dollar sign

CPU Fan True Value Table

South Bridge Specifications

Hard Disk Drive Interface

Capacity 500 320 250 160 250 160

Bytes per sector 512 512 512 512

Spindle speed 5400 5400 5400 5400

Interface SATA SATA SATA SATA

Internal transfer 830 1175 830 1175

Bytes per sector 512 512 512 512

Spindle speed 5400

Internal transfer 363 ~ 952 typical

Capacity (GB) 160 250 320 500

Bytes per sector 512

Internal transfer N/A

Screen Diagonal (mm) 11.6” 11.6” 11.6” 11.6”

Display Area (mm) 256.125 x 144 (11.6” diagonal)

Typical White Luminance (cd/m2) 200 200 200 200

also called Brightness

Response Time (Optical Rise 8 7 8 8

Electrical Interface LVDS LVDS LVDS LVDS

Viewing Angle (degree)