Datasheet PDF
Datasheet PDF
Datasheet PDF
Description
The IC products in this series are primary control switching regulator control IC’s appropriate for obtaining
stabilized DC voltages from commercial AC power.
These IC’s can directly drive power MOS FET’s, they have a timer function built in to the secondary
overcurrent protection, and they can perform intermittent operation or delayed latched shutdown as
protection operations in unusual conditions. They can be used to implement switching power supplies with
a high level of safety due to the wide range of built-in functionality.
Functions
Ordering Information
Typical Threshold Voltage
Product UVL1 OVP Notes Package
HA16107P Hi: 16.2 V 7.0 V Timer latch protection DP-16
HA16107FP Lo: 9.5 V FP-16DA
HA16108P Hi: 16.2 V Hi: 7.0 V On-off timer protection DP-16
HA16108FP Lo: 9.5 V Lo: 1.3 V (intermittent operation possible) FP-16DA
2
HA16107P/FP, HA16108P/FP
Pin Arrangement
Note 2
VIN 1 16 TL, ON/OFF
OUT 2 15 E/O
CL(+) 3 14 IN(−)
VE 4 13 NC
CL(−) 5 12 GND
Note 1
RT1 6 11 IN(+)
CT 7 10 ST
RT2 8 9 Vref
(Top view)
Notes: 1. In the SOP package models (HA16107FP and HA16108FP) pins 4, 5, and 13 are connected
inside the IC. However, all must be connected to the system ground.
2. Pin 16 is TL (HA16107), ON/OFF (HA16108).
Pin Functions
• HA16107P, HA16108P
Pin No. Symbol Pin Functions
1 VIN Input voltage
2 OUT Pulse output
3 CL (+) Current limiter
4 VE Output ground
5 CL (–) Current limiter
6 RT1 Timing resistor (rising time)
7 CT Timing capacitor
8 RT2 Timing resistor (falling time)
9 Vref Reference voltage output
10 ST Soft start
11 IN (+) Error amp (+) input
12 GND Ground
13 NC NC
14 IN (–) Error amp (–) input
15 E/O Error output
16 TL, ON/OFF Timer latch (HA16107), ON/OFF (HA16108)
3
HA16107P/FP, HA16108P/FP
• HA16107FP, HA16108FP
Pin No. Symbol Pin Functions
1 VIN Input voltage
2 OUT Pulse output
3 CL (+) Current limiter
4 GND Ground
5 GND Ground
6 RT1 Timing resistor (rising time)
7 CT Timing capacitor
8 RT2 Timing resistor (falling time)
9 Vref Reference voltage output
10 ST Soft start
11 IN (+) Error amp (+) input
12 GND Ground
13 GND Ground
14 IN (–) Error amp (–) input
15 E/O Error output
16 TL, ON/OFF Timer latch (HA16107), ON/OFF (HA16108)
4
HA16107P/FP, HA16108P/FP
Block Diagram
• HA16107P/FP
TL E/O IN (−) NC GND IN (+) ST Vref
16 15 14 13 12 11 10 9
−
EA Error amp.
140 A +
VIN 34 V
UVL1 Vref
H 6.45 V
16 A L zener type UVL2
VL VH Ref. O H UVL2
voltage V L
R Q Gen. P 4V 5V
S
4 A On/Off latch UVL1
(VTH = 7 V) ST
Vref
Q R Triangle waveform
QCLM Q S Latch reset pulse
Current
OUT limiter ON duty pulse
VC VE
1 2 3 4 5 6 7 8
VIN OUT CL (+) VE CL (−) RT1 CT RT2
• HA16108P/FP
ON/OFF E/O IN (−) NC GND IN (+) ST Vref
16 15 14 13 12 11 10 9
−
EA Error amp.
140 A +
VIN 34 V
UVL1 Vref
H 6.45 V
16 A L zener type UVL2
VL VH Ref. O H UVL2
voltage V L
R Q Gen. P 4V 5V
S
4 A On/Off latch UVL1
(VTH = 7 V) ST
1 2 3 4 5 6 7 8
VIN OUT CL (+) VE CL (−) RT1 CT RT2
Note: Dotted lines apply to the SOP package model (pins 4, 5, and 13: ground)
5
HA16107P/FP, HA16108P/FP
E/O
CT
2VBE VTL 2.2 V typ
VRT2 0V
VIN
OUT 0V
9 Vref
(connected internally)
×2 ×2
RT2 VRT2
×2 −
8 +
I2
I1 I1
Comparator for
triangle waveform
6 7 oscillation
2I2
−
×2
RT1 CT +
0.6 V
Note: When fOSC is high, the actual value will differ from that given by the formula due to the delay time.
Determine the correct constants after constructing a test circuit.
6
HA16107P/FP, HA16108P/FP
1. Timing in Normal Operation
Timing in these ICs is based on a triangular voltage waveform. The rising edge (leading edge) defines
the deadband time t DB. The falling edge (trailing edge) defines the ON-duty control band tON . PWM
output is on in the area within tON that is bounded above by the triangle wave V CT and error output V E/O .
The following pin outputs are related to PWM control:
7
HA16107P/FP, HA16108P/FP
3. Programming of Maximum ON-Duty (Du Max)
The preceding equations should be used to program the deadband or maximum ON-duty. The
following table gives a summary.
One purpose of the soft-start function is to protect the switching controller and power MOSFET from
surges at power-up. Another purpose is to let the secondary-side DC voltage rise smoothly.
When power goes off, the quick-shutdown function rapidly discharges the capacitor in the soft-start circuit
(and at the same time switches the PWM output off) to prepare for the next power-on.
The soft-start function in these ICs lets the PWM output develop smoothly from zero to the designated
pulse width at power-up. The soft-start voltage is the 3.8 V voltage value of an internal Zener diode, so the
PWM output is able to start widening gradually as soon as the soft-start function starts operating. The soft-
start function will start promptly even if CST is large.
The soft-start and quick-shutdown modes are selected automatically in the IC, under control of the UVL
signal.
8
HA16107P/FP, HA16108P/FP
• Timing waveforms
Level determined by transformer
VIN
16.2 V
VIN 9.5 V
6.45 V
5V Vref
Vref 4V
0V
VST VCT CST discharge
4.2 V
VCT, VST, 3.8 V
VE/O 2.2 V
0V
VE/O
VIN Quick shutdown
VOUT
(PWM pulse) 0V
Soft start Normal operation (Time t)
Vref
Vref
9 from Vref
from UVL2
CST
(Effective for
ST quick shutdown)
10 +
Zener +
3.8 V diode
− PWM comparator
10 µA
VCT
E/O
15 7
Note: The soft-start time constant is determined by CST and the constant-current value (typically 10 µA).
9
HA16107P/FP, HA16108P/FP
Vref overvoltage and undervoltage conditions are detected by the overvoltage detection circuit and UVL2
circuit. PWM output shuts down when Vref ≥ 8 V. UVL2 detects undervoltage with hysteresis between
approximately 4 V and 5 V. PWM output also shuts down below these voltages. It follows that PWM
output will shut off whenever the Vref pin is shorted to the power supply (VIN) or ground (GND). PWM
output also shuts off when VIN is turned on or off.
The following diagram shows how these protection functions operate when power comes on and goes off
(Vref < 6.45 V), and when a high external voltage is applied to the Vref pin (Vref > 6.45 V).
Vref
0 4V 5V 6.45 V 8 V 10 V
Vref
UVL2 OVP
1. Current-Limiter Circuit
The current limiter pin (CL) is connected to the emitter of an npn transistor, as shown in the block
diagram. The threshold voltage is 240 mV typ. The switching speed of this circuit is approximately
100 ns from detection of overcurrent to shut-down of PWM output. Switching speed increases with the
strength of the signal input to the CL pin.
Instead of simple pulse-by-pulse current limiting, in these ICs the current limiting circuit is linked to the
timer-and-latch or ON/OFF timer circuit, and also detects the degree of overcurrent. The overcurrent
value is determined from the point at which current limiting is triggered in the ON-duty cycle. With a
large overcurrent (causing current limiting to operate even at a small ON-duty), the IC automatically
shortens the timer time.
10
HA16107P/FP, HA16108P/FP
Undervoltage Lockout and PWM Output
The undervoltage lockout function turns off the PWM pulse output when the controller’s supply voltage
goes below a designated value. These ICs have two undervoltage lockout circuits. The UVL1 circuit
senses the supply voltage V IN. The UVL2 circuit senses the Vref voltage. A feature of these ICs is that
PWM output is turned on only when both voltages are above designated values. Otherwise, the IC operates
in standby mode.
The two built-in undervoltage lockout circuits make it possible to configure an extremely safe power
supply system. PWM output will shut down under a variety of abnormal conditions, such as if Vref is
shorted to ground while VIN is applied.
VIN
0 10 V 20 V 30 V 34 V
VIN
0 10 V 20 V 30 V
Vref
6.45 V
5V
4V
VIN
0 10 V 20 V 30 V
Operating region
OUT
VIN
0 10 V 20 V 30 V
PWM output shut-down region
• UVL1 and UVL2
VIN (UVL1) L H H L
Vref (UVL2) L L H H
PWM OUT L L OUT L
Standby mode
Note: Double circles indicate standby mode.
11
HA16107P/FP, HA16108P/FP
Timer Latch and ON/OFF Timer
The HA16107 has a built-in timer-latch function. The HA16108 has a built-in ON/OFF timer function.
The timer-latch function is an overvoltage protection function that combines latched shutdown of PWM
output with a timer function to vary the time until latched shutdown occurs according to the overcurrent
value. A dedicated voltage detection pin is provided in addition to Vref overvoltage protection.
The ON/OFF timer function is equivalent to the above timer-latch function without the latch. If
overcurrent is detected continuously, PWM output shuts down temporarily, then normal operation resumes.
This process repeats, temporary shutdown alternating with normal operation.
Both the timer-latch function in the HA16107 and the ON/OFF function in the HA16108 wait for an
interval after overcurrent detection before shutting down PWM output. The interval is determined by
capacitor CTM and the value of the charge/discharge current supplied internally from the IC. Normal
operation therefore continues if a single overcurrent spike is detected, while if continuous overcurrent is
detected, the current and voltage droop curves for the secondary-side output have sharp characteristics.
1. Use of Timer-Latch Pin (HA16107)
• Timer-Latch Usage
See external circuit 1 in the following diagram. Under continuous overcurrent, the CML switch turns
on, charging CTM with 12 µA. PWM output shuts down when the voltage at pin 15 exceeds 7 V.
• Overvoltage Protection Usage
See external circuit 2 in the diagram. This configuration is suitable when overvoltage is detected by an
OVP signal received through an optocoupler from the DC output on the secondary side of an AC/DC
converter. PWM output shuts down when the OVP signal allows the voltage at the TL pin to exceed 7
V. The shutdown is latched. VIN must go below approximately 6.5 V (VINR2) to release the latched
state.
VTH Latch
7.0 V (PWM output shuts down)
VTL B
0V t
OCL detected continuously
(activating pulse-by-pulse current limiter)
Notes: 1. Path A is followed if the OCL input stops before VTH is reached.
2. Path B is followed if OCL is detected continuously until the latch point is reached.
3. The latch function is cleared when VIN goes below approximately 7.0 V.
12
HA16107P/FP, HA16108P/FP
2. Use of ON/OFF Timer Pin (HA16108)
• External Circuit
16 µA
from CML
ION
16 OVP with
+ latch timer
IOFF
4 µA
HA16108
tOFF tON
VTHH
7.0 V
VTHL
1.2 V
0V t
OCL detected PWM OCL detected
(PWM output on) output (PWM output on)
shut down
tOFF ≈ C × 5.8 V
4 µA
Notes: 1. C is the capacitance of an external timing capacitor connected between this pin and ground.
2. Du is the ON-duty of the PWM output when overcurrent limiting is triggered.
3. The values of tON and tOFF for TL can be determined by the same equations as given for
the ON/OFF timer, except that 5.8 V (VTHH − VTHL) becomes VTHH = 7 V.
4. If the timer goes off during soft start or in the undervoltage lockout region, after recovery,
output will come on after the soft-start time or after the rise time to the undervoltage lockout
release point, which is determined by the time constant.
13
HA16107P/FP, HA16108P/FP
600
10% Wiring density
500
400
300
200
100
14
HA16107P/FP, HA16108P/FP
15
HA16107P/FP, HA16108P/FP
16
HA16107P/FP, HA16108P/FP
17
HA16107P/FP, HA16108P/FP
In the test circuit shown in figure 1, the operating current at the start of PWM pulse output is the standby
current.
If the resistance connected externally to the Vref pin (including R T2 ) is smaller than that of the test circuit,
the apparent standby current will increase.
↑
VIN Ist
Vref HA16107
Series + CIN
↑ IIN
Rref
18
HA16107P/FP, HA16108P/FP
Application Note
• Case:
When DC power is applied directly as the power supply of the HA16107/HA16108, without using the
transformer backup coil.
• Phenomenon:
The IC may not be activated in the case of a circuit in which VIN rises quickly (10 V/100 µs or faster),
such as that shown in figure 2.
• Reason:
Because of the IC circuit configuration, the timer latch block operates first.
If the IC power supply consists of an activation resistance and backup coil, as in an AC/DC converter, The
VIN rise speed is usually around 1 V/100 µs, and there is no risk of this phenomenon occurring.
Output
Input
VIN
HA16107
Series
VIN
Feedback
GND
Input Output
HA16107
VIN Series
18 V
1 µF C Feedback
GND
19
HA16107P/FP, HA16108P/FP
Characteristic Curves
20
10
0 10 20 30 40
Power supply voltage (V)
1.0
0.5
0 10 20 30 40
Power supply voltage (V)
20
HA16107P/FP, HA16108P/FP
200
100
0 4 8 12 16 20
Power supply voltage (V)
10
Vref Vref
UVL2 Voltage OVP Voltage
0 2 4 6 8 10
Reference voltage (V)
21
HA16107P/FP, HA16108P/FP
0 10 20 30
Power supply voltage (V)
200
CL = 100 pF
100 CL = unloaded
22
HA16107P/FP, HA16108P/FP
Ta = 25°C
50 RT1 = RT2 = 27 kΩ
CT =470 pF
Output ON duty (%)
30
20
10
0 1 2 3 4 5
23
HA16107P/FP, HA16108P/FP
Vref
24
HA16107P/FP, HA16108P/FP
VIN = 18V
Ta = 25°C
Timing resistance RT1,RT2 (kΩ)
15
CT = 470 pF
10
RT1
RT2
5
0
30 40 50 60 70 80
CT = 470 pF
1000
Temperature fluctuation (ppm)
−1000
−2000
−20 0 25 50 75 85
25
HA16107P/FP, HA16108P/FP
−5
−10
−20 0 25 50 75 85
Ambient temperature (°C)
−5
−10
−20 0 25 50 75 85
Ambient temperature (°C)
26
HA16107P/FP, HA16108P/FP
−5
−10
−20 0 25 50 75 85
Ambient temperature (°C)
5
Output ON duty variance (%)
0
f = 100 kHz
f = 300 kHz
−5
f = 600 kHz
−10
−20 0 25 50 75 85
Ambient temperature (°C)
27
HA16107P/FP, HA16108P/FP
300
C
T =
12
0
pF
27
0
pF
100
Oscillator frequency (kHz)
90 47
0
pF
70
50
82
0
pF
30
33
00
pF
10
9
5 7 10 30 50 70 100
Timing resistance RT1 (= RT2) (kΩ)
28
HA16107P/FP, HA16108P/FP
20
IO
10 TL + 1 F
OUT
0 CL
CL (+)
1000 pF
27 kΩ
500 R T1
IO (mA)
470 pF
0 CT ST
CST
+ 1 F
RT2 Vref
−500
27 kΩ
30
Vout (V)
20
10
500
I O (mA)
−500
200 ns/div
29
HA16107P/FP, HA16108P/FP
RT2 Vref
3 27 kΩ
A
2
1 Triangle
wave
0
CL(+) when
input at a
duty of 0%
5 VTL
B
4
CTL discharged at 4 µA
VTL (V)
3 CTL discharged at 12 µA
t
2
A Enlargement of section B
1
VTL CTL discharged at 4 µA
0
t
tON tOFF 0.5 sec/div
a to b : PWM pulse output is High
Output pulse shutdown region b : The point where overcurrent
is detected
SW ON SW OFF
b to c : PWM pulse output is Low.
30
HA16107P/FP, HA16108P/FP
4 C ST
+ 1 µF
R T2
3 27 k‰
2
A
1 Triangle
wave
0
CL(+) when
input at a
0.5 sec/div duty of 0%
4 CTL discharged at 4 µA
CTL discharged at 12 µA
3
t
2
A Enlargement of section B
1 V TL CTL discharged at 4 µA
0.5 sec/div
t
t ON t OFF t ON t OFF
a to b : PWM pulse output is High.
b : The point where overcurrent
is detected.
SW ON SW OFF Output pulse shutdown region
b to c : PWM pulse output is Low.
31
HA16107P/FP, HA16108P/FP
60
40 0
135
0 180
10 k 30 k 100 k 300 k 1M 3M 10 M 30 M 100 M
Input signal frequency fIN (Hz)
5.0
ON
Normal operation Pulse by pulse
VOUT (DC) (V)
0 1 2 3 4
IOUT (DC) (A)
HA16107 (Latch shut-down)
5.0
ON Pulse by pulse
VOUT (DC) (V)
A
2.5
B A Heavy load
B Light load
0 1 2 3 4
IOUT (DC) (A)
HA16108 (Intermittent operation by means of ON/OFF timer)
32
HA16107P/FP, HA16108P/FP
82 kΩ
1W 2SK1567 40T 6T + 5V
470 µF OUTPUT
51 Ω −
HZP 16 −
1.5 Ω 23T
RFI 3W
HRP 32
Current Sense
18.9 V
FILTER +
50 V
22 µF OVP
HZP 16 Detector
AC
VIN TL Timerlatch
INPUT
Capacitor
QCLM
−++
16
1
+ 16 V
1 µF
16
µA
E/O −
4 µA
PWM Comparator
VC
OUT
140
330
OUT
µA
15
110 Ω
2
kΩ
L
H
ON/OFF Latch
(V TH= 7V)
UVL1
VE
S
R Q
VL VH
CL(+) IN(−)
QS
QR
Error amp.
14
3
Current
Sense 510 kΩ
circuit
generation
voltage
reference
Zener type
6.45 V
UVL1&UVL2
L.P.F. 51 Ω VE NC 68
Phase kΩ
13
4
Vref
limiter
Current
UVL1
Triangle wave
4700 pF Comp.
VIN
O
P
V
ST
CL(−)
L
H
UVL2
12
5
4V 5V
GND
34 V
27 kΩ IN(+)
11
6
Vref
3.225 V
RT1
UVL2
470 pF
ST
10
Soft Start
7
− Cap.
3.4 V 10 µA
33
34
HA16107P/FP, HA16108P/FP
• Forward Transformer Application Example
Bridge diode Power thermister
+
AC 200 V
INPUT − 100 µF
DFG1C8 HRW26F 47 µH
HA17431P
330 Ω +
RB
0.3 φ + 16 V 3.3 kΩ
0.5 φ
1 W 82 kΩ 50 T
8T − 1000 µF
(Start-up resistor) 1.8 kΩ + DC
*
− OUT
10 kΩ (5 V)
3.3 µF
4.7 kΩ
+ 0.3 φ + B
Timer latch 1 µF − (Soft start 1 µF 0.47 µF 50 T 0.5 φ 50 V
capacitor) − + − —22 µF
capacitor 8T Secondary error amplifier −
+ *
16 15 14 13 12 11 10 9
TL E/O IN NC IN ST Vref
(−) (+)
HZP16
HA16107P/108P 13 kΩ TLP521
2SK1567
CL
VOUT (+) RT1 CT CT2
1 2 3 4 5 6 7 8 51 Ω
* Bifiler transfomer core size
3W EI-30 equivalent product
13 kΩ 470 pF 1.5 Ω (Current sense)
110 Ω
VIN
RB
OVP detector
VIN OUT
CL(+)
TL
+
1 µF
When the OVP detection Zener diode turns on, latch shutdown of the output
is performed after the elapse of the time determined by the capacitance
connected the TL pin.
35
HA16107P/FP, HA16108P/FP
Package Dimensions
Unit: mm
19.20
20.00 Max
16 9
7.40 Max
6.30
1 8
1.3
1.11 Max
7.62
+ 0.13
2.54 ± 0.25 0.48 ± 0.10 0.25 – 0.05
0° – 15°
Hitachi Code DP-16
JEDEC Conforms
EIAJ Conforms
Mass (reference value) 1.07 g
Unit: mm
10.06
10.5 Max
16 9
5.5
1 8
*0.22 ± 0.05
0.20 ± 0.04
7.80 +– 0.30
0.20
2.20 Max
0° – 8°
0.10 ± 0.10
*0.42 ± 0.08
0.40 ± 0.06
0.15
0.12 M
Hitachi Code FP-16DA
JEDEC —
*Dimension including the plating thickness EIAJ Conforms
Base material dimension Mass (reference value) 0.24 g
36
HA16107P/FP, HA16108P/FP
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as fail-
safes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.
Hitachi, Ltd.
Semiconductor & Integrated Circuits.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL NorthAmerica : http:semiconductor.hitachi.com/
Europe : http://www.hitachi-eu.com/hel/ecg
Asia (Singapore) : http://www.has.hitachi.com.sg/grp3/sicd/index.htm
Asia (Taiwan) : http://www.hitachi.com.tw/E/Product/SICD_Frame.htm
Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm
Japan : http://www.hitachi.co.jp/Sicd/indx.htm
For further information write to:
Hitachi Semiconductor Hitachi Europe GmbH Hitachi Asia Pte. Ltd. Hitachi Asia (Hong Kong) Ltd.
(America) Inc. Electronic components Group 16 Collyer Quay #20-00 Group III (Electronic Components)
179 East Tasman Drive, Dornacher Straβe 3 Hitachi Tower 7/F., North Tower, World Finance Centre,
San Jose,CA 95134 D-85622 Feldkirchen, Munich Singapore 049318 Harbour City, Canton Road, Tsim Sha Tsui,
Tel: <1> (408) 433-1990 Germany Tel: 535-2100 Kowloon, Hong Kong
Fax: <1>(408) 433-0223 Tel: <49> (89) 9 9180-0 Fax: 535-1533 Tel: <852> (2) 735 9218
Fax: <49> (89) 9 29 30 00 Fax: <852> (2) 730 0281
Hitachi Europe Ltd. Hitachi Asia Ltd. Telex: 40815 HITEC HX
Electronic Components Group. Taipei Branch Office
Whitebrook Park 3F, Hung Kuo Building. No.167,
Lower Cookham Road Tun-Hwa North Road, Taipei (105)
Maidenhead Tel: <886> (2) 2718-3666
Berkshire SL6 8YA, United Kingdom Fax: <886> (2) 2718-8180
Tel: <44> (1628) 585000
Fax: <44> (1628) 778322
Copyright ' Hitachi, Ltd., 1998. All rights reserved. Printed in Japan.
37
HA16107P/FP, HA16108P/FP
Revision Record
Rev. Date Contents of Modification Drawn by Approved by
0.0 Oct. 11, 1994 Initial issue A. Koizumi M. Yamamura
0.1 Oct. 11, 1994 Initial issue A. Koizumi M. Yamamura
0.2 Nov. 12, 1994 Initial issue A. Koizumi M. Yamamura
38