Bituprime SB: Solvent Based Bitumen Primer

BITuprime sb
Solvent based bitumen primer

Low viscosity, fast drying and good adhesion between the membrane
and the concrete surface
characteristics
► Improves the adhesion between bitumen based sheet
membranes and coatings
► Cold applied, does not require heating
► Binder for dust particles
► Anti corrosive
TDS_Bituprime SB_RTL_1116
► Conforms to the following standards
► ASTM D 41 - Asphalt primer for roofing, damp proofing
and waterproofing
► BS 3416, Type A Class C - Bitumen based coatings for
cold application, suitable for use in contact with potable
water
fast drying
1
DESCRIPTION
Bituprime SB is a quick drying solvent based low viscosity unsound and friable concrete shall be removed and
bitumen primer. It is used as a primer coat on masonry and repaired with a suit-able Polycrete* concrete repair mortar.
concrete substrates to improve the adhesion of bitumen The surface must be dry before priming with Bituprime SB.
based membranes and coatings. Bituprime SB is low in Application
viscosity, which allows it to penetrate into the concrete Mix the contents of the pail or drum for a few minutes to
pores and improve the adhesion between the membrane remove any sediments. Apply the primer @4-6 m²/L to a
and the concrete surface. In addition to that, the primer clean smooth and dry surface by brush/roller. Allow the
also acts as a binder for the dust particles which gets primer to dry prior to the application of the membrane.
accumulated on the concrete surface even after cleaning. For highly porous surfaces application of a second coat is
Fields of application recommended.
Bituprime SB is used as a primer and sealer coat prior coverage
to the application of bitumen based waterproofing The coverage is 4-6 m²/L/coat. However, the coverage
membranes and coatings. will depend on the porosity of the substrate. In order to
application instructions ascertain the exact coverage, a trial application is carried
out at site.
The application temperature should be between 5°C to
55°C. Application procedures may vary slightly depending storage & shelf life
upon site conditions. The general recommended guidelines The pails and drums must be stored in a covered, dry and
for the application of the primer is as follows: shaded area, away from direct sunlight, UV and other
Surface preparation sources of heat and protected from extreme temperatures.
The surface shall be cleaned thoroughly of all contaminants The shelf life of the product is up to 12 months if stored as
like dust, traces of curing compound, oil and grease. All per the recommendations. Excessive exposure to sunlight
surface imperfections, nail head protrusions, structurally
and UV will result in the deterioration of the quality of the technical specification
product and reduce its shelf life.
PROPERTIES VALUES TEST
Health & safety STANDARDS
Bituprime SB contains volatile solvent with a low flash Density, [g/cc] 0.85-0.90 astm d 1475
point (38°C). It should be kept far away from naked flame. Solid content, >40 astm d 1644
Avoid inhalation of vapors and ensure there is adequate [% by wt]
ventilation in the work place. Gloves, protective masks and All values given are subject to 5-10% variation
goggles should be worn during application. If swallowed
seek medical attention immediately.
Apart from the information given here it is also important to observe the relevant
guidelines and regulations of various organisations and trade associations as
supply well as the respective standards. The aforementioned characteristics are based
on practical experience and applied testing. Warranted properties and possible
Bituprime SB 20L pail & 200L drum uses which go beyond those warranted in this information sheet require our
Polycrete 25kg bag written confirmation. All data given was obtained at an ambient and material
temperature of +23°C and 50 % relative air humidity at laboratory conditions
* Refer to website for TDS unless specified otherwise. Please note that under other climatic conditions
hardening can be accelerated or delayed.
The information contained herein, particularly recommendations for the
handling and use of our products, is based on our professional experience.
As materials and conditions may vary with each intended application, and
thus are beyond our sphere of influence, we strongly recommend that in each
case sufficient tests are conducted to check the suitability of our products
for their intended use. Legal liability cannot be accepted on the basis of the
contents of this data sheet or any verbal advice given, unless there is a case
of wilful misconduct or gross negligence on our part. This technical data sheet
supersedes all previous editions relevant to this product.
TDS_Bituprime SB_RTL_1116
Henkel Polybit Industries Ltd.

PO Box: 293, Umm Al Quwain, UAE
Phone: +971 (6) 76 70 777; Fax: +971 (6) 76 70 197
henkelpolybit@henkelpolybit.com; www.henkelpolybit.com

Bituprime SB: Solvent Based Bitumen Primer

Uploaded by

Copyright:

Available Formats

Bituprime SB: Solvent Based Bitumen Primer

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bituprime SB: Solvent Based Bitumen Primer

Uploaded by

Copyright:

Available Formats

BITuprime sb

Solvent based bitumen primer

Henkel Polybit Industries Ltd.

You might also like