Features: Video Decoder Scaling Engine/Panel Interface

MST717A/MST717A-A
Small Size LCD TV Processor with Video Decoder

Preliminary Data Sheet Version 0.1
FEATURES
Video Decoder Scaling Engine/Panel Interface
Supports NTSC, PAL and SECAM video input Supports digital panels up to 1366x768
formats Supports single 8-bit TTL panel outputs
2D NTSC and PAL comb-filter for Y/C Supports various displaying modes
separation of CVBS input Supports horizontal panorama scaling
Multiple CVBS and S-video inputs Digital PWM Controller
Supports Closed-caption and V-chip Integrated general purpose digital PWM
ACC, AGC, and DCGC (Digital Chroma Gain control loop
Control) Programmable startup operating frequency
Analog Input and period with output voltage regulation
Supports RGB input format from PC, Programmable output current regulation;
camcorders and GPS 40KHz~70KHz switching frequency, sync. to
Supports video input 480i, 480p, 576i, 576p, HSYNC possible
720p, 1080i; RGB input resolution in 640x480, Burst-mode or continuous-mode for output
800x480, and 800x600 (SVGA) current regulation; 150Hz~300Hz burst-mode
3-channel low-power 10-bit ADCs integration frequency, sync. to VSYNC possible
for RGB Programmable protection level for input
Supports RGB composite sync input (CSYNC), voltage and fault detection
SOG, HSYNC, and VSYNC Miscellaneous
On-chip clock synthesizer and PLL Built-in MCU
Auto-position adjustment, auto-phase 3-wire serial bus interface for configuration
adjustment, auto-gain adjustment, and setup
auto-mode detection Built-in step-down PWM circuit for input 2.5V
Color Engine Built-in VCOM DC level adjusting circuits
Brightness, contrast, saturation, and hue Built-in internal OSD with 256 programmable
adjustment fonts, 16-color palettes, and 12-bit color
9-tap programmable multi-purpose FIR (Finite resolution
Impulse Response) filter Supports external OSD
Differential 3-band peaking engine Spread spectrum clocks
Luminance Transient Improvement (LTI) Optional 3.3V / 5V output pads with
Chrominance Transient Improvement (CTI) programmable driving current
Black Level Extension (BLE) 128-pin PQFP package
White Level Extension (WLE)
Favor Color Compensation (FCC)
3-channel gamma curve adjustment
Version 0.1 -1- 1/2/2006

Copyright © 2005 MStar Semiconductor, Inc. All rights reserved.
MST717A/MST717A-A
BLOCK DIAGRAM
R
RGB
G
Auto Function for RGB ADC Input
B
CVBS 1/2 Switch
SY/CVBS
M
2-Channel Video Decoder YC Separation Chroma
S-Video 1/2 U
SC AFE Timing Generator 2D Comb Filter Demodulator X
3x3 Color Space CSC

MACE Scaling Engine
Conversion (RGB to YCbCr)
Display
OSD Gamma Display Unit
Device
T-CON
MCU BIU
Flash Memory or External MCU

EEPROM
SYSTEM APPLICATION DIAGRAM

Flash / ROM 2.5V Power Supply
Micro- PWM Digital

Controller Step-Down PWM
TV / Cable Signal TV Tuner
Additional CVBS Video

TCON To Digital Panel
DVD / VCD S-Video Signal Decoder
Additional S-Video
Analog RGB Signal
Deinterlacer /
Scaler
Version 0.1 -2- 1/2/2006

MST717A/MST717A-A
GENERAL DESCRIPTION
The MST717A is a high quality ASIC for NTSC/PAL/SECAM car TV application. It receives analog
NTSC/PAL/SECAM CVBS and S-Video inputs from TV tuners, DVD or VCR sources, including weak and distorted
signals, as well as analog RGB input from GPS systems. Automatic gain control (AGC) and 8-bit 3-channel A/D
converters provide high resolution video quantization. With automatic video source and mode detection, users
can easily switch and adjust variety of signal sources. Multiple internal adaptive PLLs precisely extract pixel
clock from video source and perform sharp color demodulation. Built-in line-buffer supports adaptive 2-D
comb-filter, 2-D sharpening, and synchronization stabler in a condense manner. The output format of
MST717A supports 6-bit or 8-bit TTL digital TFT-LCD modules.
Version 0.1 -3- 1/2/2006

MST717A/MST717A-A
PIN DIAGRAM (MST717A)
VREXT_CDAC
AVDD_MPLL
AVDD_XTAL
AVDD_OPLL
AVDD_DAC
DTCON[1]
DTCON[2]
DTCON[3]
HSYNCIN
VSYNCIN
VCOMDC
ROM_EN
BOUT[5]
BOUT[4]
BOUT[3]
BOUT[2]
BOUT[1]
BOUT[0]
VDDC
XOUT
GND
GND
GND
GND
GND
XIN
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
GND 1 102 INT_OUT
VCLAMP 2 101 GND
REFM 3 Pin 1 100 VDDP
REFP 4 99 DTCON[4]
AVDD_ADC 5 98 DTCON[5]
SOGIN 6 97 GOUT[5]
BINP 7 96 GOUT[4]
BINM 8 95 GOUT[3]
GINP 9 94 GOUT[2]
GINM 10 93 GOUT[1]
RINP 11 92 GOUT[0]
RINM 12 91 DTCON[6]
AVDD_ADC 13 90 DTCON[7]
C1INP 14 89 ROUT[5]
C1INM 15 88 ROUT[4]
YS1INP 16 87 ROUT[3]
YS1INM 17 86 ROUT[2]
XXXXX
XXXXXXXXXXX
MST717A
C2INP 18 85 ROUT[1]
C2INM 19 84 ROUT[0]
YS2INP 20 83 GPIO_P07
YS2INM 21 82 VDDP
CVBS1P 22 81 GND
CVBS1M 23 80 DTCON[8]
CVBS2P 24 79 DTCON[9]
CVBS2M 25 78 DTCON[10]
AVDD_GMC 26 77 CLKO
VIN 27 76 GPIO_P13
FAULTZ 28 75 GPIO_P12
FB2_DPWM 29 74 GPIO_P11
FB1_DPWM 30 73 GPIO_P10
AVDD_SAR 31 72 RESET
AVSS_SAR 32 71 PWMD1
AVSS_DPWM 33 70 PWMD2
AVDD_DPWM 34 69 GND
Q2 35 68 POWER_ON_RSTN/CS
Q1 36 67 SCL
GND 37 66 SDA
AVDD_PWM 38 65 INT
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
PWMOUT2
FB2
SENSE2
PWMOUT1
FB1
SENSE1
SAR0
SAR1
SAR2
GPIO_P24/PWMD3
GPIO_P25/PWMD4
SCK
GPIO_P00
GPIO_P01
GPIO_P02
GPIO_P03
GPIO_P04
GPIO_P05
GPIO_P06
VDDC
VDDP
SDI
CSN
PGOOD
GND
SDO
Version 0.1 -4- 1/2/2006

MST717A/MST717A-A
PIN DESCRIPTION
Analog Interface
Pin Name Pin Type Function Pin
VCLAMP CVBS/YC Mode Clamp Voltage Bypass 2
REFM Internal ADC Bottom De-coupling Pin 3
REFP Internal ADC Top De-coupling Pin 4
SOGIN Analog Input Sync-on-Green slicer input 6
BINP Analog Input Analog B Input of VGA 7
BINM Analog Input Reference Ground for Analog B Input of VGA 8
GINP Analog Input Analog G Input of VGA 9
GINM Analog Input Reference Ground for Analog G Input of VGA 10
RINP Analog Input Analog R Input of VGA 11
RINM Analog Input Reference Ground for Analog R Input of VGA 12
C1INP Analog Input Analog Chroma Input for TV S-Video1 / 14
Analog Composite Input of TV CVBS4
C1INM Analog Input Reference Ground for Analog Chroma Input of TV S-Video1 15
/ Analog Composite Input of TV CVBS4
YS1INP Analog Input Analog Luma Input of TV S-Video1 / 16
YS1INM Analog Input Reference Ground for Analog Luma Input of TV S-Video1 / 17
C2INP Analog Input Analog Chroma Input for TV S-Video2 18
C2INM Analog Input Reference Ground for Analog Chroma Input of TV S-Video2 19
YS2INP Analog Input Analog Luma Input of TV S-Video2 20
YS2INM Analog Input Reference Ground for Analog Luma Input of TV S-Video2 21
CVBS1P Analog Input Analog Composite Input for TV CVBS1 22
CVBS1M Analog Input Reference Ground for Analog Composite Input of TV CVBS1 23
CVBS2P Analog Input Analog Composite Input for TV CVBS2 24
CVBS2M Analog Input Reference Ground for Analog Composite Input of TV CVBS2 25
VREXT_CDAC Analog Input Reference Current Generator, 820 ohm to Ground 117
HSYNCIN Schmitt Trigger Input HSYNC / Composite Sync for VGA Input 125
w/ 5V-tolerant
VSYNCIN Schmitt Trigger Input VSYNC for VGA Input 124
w/ 5V-tolerant
Version 0.1 -5- 1/2/2006

MST717A/MST717A-A
Digital Panel Output Interface

CLKO Output Display Clock Output 77
ROUT[5:0] Output Red channel Output [5:0] 89-84
GOUT[5:0] Output Green channel Output [5:0] 97-92
BOUT[5:0] Output Blue channel Output [5:0] 108-103
DTCON[10:1] Output TCON Output 78-80, 90,
91, 98, 99,
109-111
VCOM Interface
VCOMDC Analog Output Reference DC voltage output for common amplifier. 118
Switching Power and PWM Interface

PWMOUT Output Switching Pulse Output for DC-DC Converter 39
FB2 Analog Input Error Voltage Feedback Input Pin for PWM2; 40
voltage = 1.2V
SENSE2 Analog Input Sense Circuit Connection for PWM2 41
PWMOUT1 Output Switching Pulse Output for DC-DC Converter 42
FB1 Analog Input Error Voltage Feedback Input Pin for PWM1; 43
voltage = 1.2V
SENSE1 Analog Input Sense Circuit Connection for PWM1 44
PGOOD Output Power Good Indicator 45
Internal MCU Interface with Serial Flash Memory

SAR2 Analog Input SAR Low Speed ADC Input 2 49
SCK Output SPI Interface Sampling Clock 52
SDI Output SPI Interface Data-In 53
SDO Input w/ 5V-tolerant SPI Interface Data-Out 54
CSN Output SPI Interface Chip Select 55
GPIO_P00-GPIO_P06 I/O w/ 5V-tolerant General Purpose Input/Output; 4mA driving 58-64
Version 0.1 -6- 1/2/2006

MST717A/MST717A-A

strength
GPIO_P10-GPIO_P13 I/O w/ 5V-tolerant General Purpose Input/Output; 4mA driving 73-76
strength
INT Input Interrupt Input for IR Receiver 65
SDA I/O w/ 5V-tolerant 3-Wire Serial Bus Data 66
SCL Input w/ 5V-tolerant 3-Wire Serial Bus Clock 67
POWER_ON_RSTN/CS Input w/ 5V-tolerant Power On Reset Signal/Chip Selection for 3-wire 68
Serial
GPIO_P07 I/O w/ 5V-tolerant General Purpose Input/Output; 4mA driving 83
strength
Digital PWM Interface

Q1 Output DPWM Output 1 36
Q2 Output DPWM Output 2 35
st
FB1_DPWM Analog Input Input for 1 Feedback Loop 30
nd
FB2_DPWM Analog Input Input for 2 Feedback Loop 29
FAULTZ Analog Input Fault Detection (Low Enable) 28
VIN Analog Input System Input Voltage Detection 27
Misc. Interface
RESET Schmitt Trigger Input Hardware Reset; active high 72
w/ 5V-tolerant
XIN Analog Input Crystal Oscillator Input 123
XOUT Analog Output Crystal Oscillator Output 122
GPIO_P24/PWMD3 Output General Purpose Input/Output; 4mA driving strength/ 56
Pulse Width Modulation Output; 4mA driving strength
GPIO_P25/PWMD4 Output General Purpose Input/Output; 4mA driving strength/ 57
Pulse Width Modulation Output; 4mA driving strength
PWMD2 Output Pulse Width Modulation Output; 4mA driving strength 70
PWMD1 Output Pulse Width Modulation Output; 4mA driving strength 71
INT_OUT Output Mode Detection Interrupt Output 102
ROM_EN Input Internal ROM Enable. 112
0: Disable.
1: Enable.
Version 0.1 -7- 1/2/2006

MST717A/MST717A-A
Power Pins
AVDD_ADC 2.5V Power ADC Power 5, 13
AVDD_GMC 5V Power GMC Power 26
AVDD_SAR 5V Power SAR Power 31
AVDD_DPWM 5V Power DPWM Power 34
AVDD_PWM 5V Power PWM Power 38
AVDD_OPLL 2.5V Power OPLL Power 116
AVDD_DAC 5V Power Voltage DAC Power 119
AVDD_XTAL 5V Power XTAL Power 120
AVDD_MPLL 2.5V Power MPLL Power 127
VDDC 2.5V Power Digital Core Power 50, 113
VDDP 3.3V/5V Power Digital Input/Output Power 46, 82, 100
AVSS_SAR Ground SAR Ground 32
AVSS_DPWM Ground DPWM Ground 33
GND Ground Ground 1, 37, 51, 69, 81, 101,
114, 115, 121, 126, 128
Version 0.1 -8- 1/2/2006

MST717A/MST717A-A
ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings
Parameter Symbol Min Typ Max Units
5.0V Supply Voltages VVDD_50 -0.3 5.5 V
Input Voltage (5V tolerant inputs) VIN5Vtol -0.3 5.0 V
Input Voltage (non 5V tolerant inputs) VIN -0.3 VVDD_33 V
Ambient Operating Temperature (commercial use) TA 0 70 °C
Ambient Operating Temperature (extended temp. range) TA -20 80 °C
Storage Temperature TSTG -40 125 °C
Junction Temperature TJ 125 °C
Thermal Resistance (Junction to Air) Natural Conversion θJA TBD °C/W
Thermal Resistance (Junction to Case) Natural Conversion θJC TBD °C/W
Note: Stress above those listed under Absolute Maximum Rating may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these or any other conditions outside of those indicated in the
operation sections of this specification is not implied. Exposure to absolute maximum ratings for extended periods may
affect device reliability.
ORDERING GUIDE MARKING INFORMATION

Model Temperature Package Package MST717A/MST717A-A
Part Number
Range Description Option
Lot Number
MST717A 0°C to +70°C PQFP 128 Operation Code A
MST717A-A -20°C to +80°C PQFP 128 Operation Code B

Date Code (YYWW)
MST717A-LF 0°C to +70°C PQFP 128
MST717A-A-LF -20°C to +80°C PQFP 128

Note: Product suffix “-LF” represents lead-free version
and “-A” represents extended temperature range.
DISCLAIMER
MSTAR SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE
TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. NO
RESPONSIBILITY IS ASSUMED BY MSTAR SEMICONDUCTOR ARISING OUT OF THE APPLICATION
OR USER OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY
LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS.
Electrostatic charges accumulate on both test equipment and human body and can discharge
without detection. MST717A comes with ESD protection circuitry; however, the device may be
permanently damaged when subjected to high energy discharges. The device should be handled
with proper ESD precautions to prevent malfunction and performance degradation.
REVISION HISTORY
Document Description Date
MST717A_ds_v01 Initial release Dec 2005
Version 0.1 -9- 1/2/2006

MST717A/MST717A-A
MECHANICAL DIMENSIONS
D1
A
D2 A2 A1
E1
E2
E
L1
θ1
θ2
R1 c
R2
Gauge Plane
θ
0.25mm
Seating Plane
θ3
b e
L
Millimeter Inch Millimeter Inch

Symbol Symbol
Min. Nom. Max. Min. Nom. Max. Min. Nom. Max. Min. Nom. Max.
A - - 3.40 - - 0.134 θ 0° - 7° 0° - 7°
A1 0.25 - - 0.010 - - θ1 0° - - 0° - -
A2 2.50 2.72 2.90 0.098 0.107 0.114 θ2, θ3
7° Ref 7° Ref
D 23.20 0.913 (Alloy)
D1 20.00 0.787 θ2, θ3

15° Ref 15° Ref
(Copper)
D2 18.50 0.728
b 0.170 0.200 0.270 0.007 0.008 0.011
E 17.20 0.677
c 0.11 0.15 0.23 0.004 0.006 0.009
E1 14.00 0.551
e 0.50 BSC. 0.020 BSC.
E2 12.50 0.492
L 0.73 0.88 1.03 0.029 0.035 0.041
R1 0.13 - - 0.005 - -
L1 1.60 Ref 0.063 Ref
R2 0.13 - 0.30 0.005 - 0.012
S 0.20 - - 0.008 - -
Version 0.1 - 10 - 1/2/2006


Features: Video Decoder Scaling Engine/Panel Interface

Uploaded by

Copyright:

Available Formats

Features: Video Decoder Scaling Engine/Panel Interface

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Features: Video Decoder Scaling Engine/Panel Interface

Uploaded by

Copyright:

Available Formats

MST717A/MST717A-A

Small Size LCD TV Processor with Video Decoder

Version 0.1 -1- 1/2/2006

3x3 Color Space CSC

Flash Memory or External MCU

SYSTEM APPLICATION DIAGRAM

Micro- PWM Digital

TV / Cable Signal TV Tuner

Additional CVBS Video

Version 0.1 -2- 1/2/2006

Version 0.1 -3- 1/2/2006

PIN DIAGRAM (MST717A)

Version 0.1 -4- 1/2/2006

Version 0.1 -5- 1/2/2006

Digital Panel Output Interface

Switching Power and PWM Interface

Internal MCU Interface with Serial Flash Memory

Version 0.1 -6- 1/2/2006

Pin Name Pin Type Function Pin

Digital PWM Interface

Version 0.1 -7- 1/2/2006

Version 0.1 -8- 1/2/2006

ORDERING GUIDE MARKING INFORMATION

MST717A-A -20°C to +80°C PQFP 128 Operation Code B

MST717A-LF 0°C to +70°C PQFP 128

MST717A-A-LF -20°C to +80°C PQFP 128

Version 0.1 -9- 1/2/2006

Millimeter Inch Millimeter Inch

D1 20.00 0.787 θ2, θ3

Version 0.1 - 10 - 1/2/2006

You might also like