Intelligent Power Devices (IPDs)

MIP0221SY, MIP0222SY, MIP0223SY, MIP0224SY, MIP0225SY, MIP0226SY, MIP0227SY

Silicon MOS IC
■ Features
● Single chip IC with high breakdown voltage power MOS FET and unit: mm
CMOS control circuits 10.5±0.5
● Allowing to input worldwide mains (AC 85 to 274V) 4.5±0.2
9.5±0.2 1.4±0.1
● A pulse-by-pulse overcurrent protection circuit and a timer auto-

2.8±0.2
1.5±0.2
8.0±0.2
restart circuit are integrated.

6.8±0.1
■ Applications

2.8±0.2
15.4±0.3
● Switching power supply (to 90W) φ3.7±0.1

4.2±0.3
● AC adaptor
● Battery charger 1.4±0.1 2.5±0.2

13.5±0.5

Solder Dip
■ Absolute Maximum Ratings (Ta = 25 ± 3°C) 0.8±0.1

9.3
Parameter Symbol Ratings Unit
2.54±0.3
0.6±0.1
Drain voltage VD 700 V 5.08±0.5

Control voltage VC 8 V 1: Control

MIP0221SY 0.3 2: Source
3: Drain
1 2 3
MIP0222SY 0.585 EIAJ: SC-46
TO-220 Type Package (a)
MIP0223SY 1.15
Output current ID MIP0224SY 1.72 A
MIP0225SY 2.4
MIP0226SY 2.9
MIP0227SY 3.5
Control current IC 0.1 mA
Channel temperature Tch 150 °C
Storage temperature Tstg −55 to +150 °C

■ Block Diagram

Auto-restart Drain pin

Control pin Shutdown/Auto-restart
Auto-restart current-source
Shunt Power supply
regulator for internal circuit
+
5.7V 1/2 1/2 1/2
4.7V -
- Ron X ID
+ +
Timer auto-restart circuit -

PWM Q
Thermal S Power
control current shutdown MOS FET
circuit Restarting R
Q
trigger circuit
Max Duty
Clock Q
S
Sawtooth - Leading edge
+ R blanking
Q

RE Low pass filter Minimum ON-time

delay circuit
Source pin

1
Intelligent Power Devices (IPDs) MIP0221SY/0222SY/0223SY/0224SY/0225SY/0226SY/0227SY

■ Electrical Characteristics (TC = 25 ± 2°C)

Parameter Symbol Conditions min typ max Unit
Output frequency fOSC IC = 2mA 90 100 110 kHz
Control functions Maximum duty cycle MAXDC IC = 2mA 64 67 70 %
Minimum duty cycle MINDC IC = 10mA 3 %
VC = 0 −2.4 −1.9 −1.2
Control pin charging current IC mA
VC = 5V −2 −1.5 − 0.8
Auto-restart threshold voltage VC(on) 5 5.7 6.3 V
Auto-restart Lockout threshold voltage VC(off) 4 4.7 5.3 V
Auto-restart hysteresis voltage ∆VC 0.5 1 1.5 V
Auto-restart duty cycle TSW/TTIM 5 8 %
Auto-restart frequency fTIM 1.2 Hz
MIP0221SY 0.23 0.25 9.28
MIP0222SY 0.45 0.5 0.55
MIP0223SY 0.9 1 1.1
Self-protection
MIP0224SY ILIMIT 1.35 1.5 1.65 A
current limit
MIP0225SY 1.8 2 2.2
Circuit protection MIP0226SY 2.25 2.5 2.75
MIP0227SY 2.7 3 3.3
Leading edge blanking delay ton(BLK) IC = 3mA 0.25 µs
Current limit delay td(OCL) IC = 3mA 0.1 µs
Thermal shutdown temperature TOTP IC = 3mA 130 140 150 °C
Power-up reset threshold voltage VC reset 2.3 3.3 4.2 V
MIP0221SY ID = 0.025A 31.2 36
MIP0222SY ID = 0.1A 15 18
MIP0223SY ID = 0.2A 8.5 10
ON-state resistance MIP0224SY RDS(on) ID = 0.3A 5.8 6.7 Ω
MIP0225SY ID = 0.3A 4 5
Output MIP0226SY ID = 0.3A 3.3 4
MIP0227SY ID = 0.3A 2.6 3
OFF-state current IDSS VDS = 650V, Output MOS FET disabled 0.01 0.25 mA
Breakdown voltage VDSS ID = 0.25mA, Output MOS FET disabled 700 V
Rise time tr 0.1 0.2 µs
Fall time tf 0.1 0.2 µs
Drain supply voltage VD(MIN) 36 V
Shunt regulator voltage VC IC = 3mA 5.4 5.7 6.1 V
Power supply voltage
ICD1 Output MOS FET enabled 0.7 1.4 1.8 mA
Control supply/discharge current
ICD2 Output MOS FET disabled 0.5 0.8 1.1 mA

2
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.

Please read the following notes before using the datasheets

A. These materials are intended as a reference to assist customers with the selection of Panasonic
semiconductor products best suited to their applications.
Due to modification or other reasons, any information contained in this material, such as available
product types, technical data, and so on, is subject to change without notice.
Customers are advised to contact our semiconductor sales office and obtain the latest information
before starting precise technical research and/or purchasing activities.
B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but
there is always the possibility that further rectifications will be required in the future. Therefore,
Panasonic will not assume any liability for any damages arising from any errors etc. that may ap-
pear in this material.
C. These materials are solely intended for a customer's individual use.
Therefore, without the prior written approval of Panasonic, any other use such as reproducing,
selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.

2001 MAR