Vertical Deflection Output Ic: Ics For TV
Vertical Deflection Output Ic: Ics For TV
Vertical Deflection Output Ic: Ics For TV
AN5534N
Vertical deflection output IC
■ Overview Unit: mm
7.7±0.3
The AN5534N is a vertical deflection output IC for
12
television and CRT monitor. Incorporating a sawtooth
(1.3)
wave generator, this IC enables you to form an AC/DC
(10.0)
φ3.6
(1.27)
feedback-loop by itself only.
29.75±0.30
28.0±0.3
20.0±0.3
29.6±0.3
■ Features
(1.27)
0.6 +0.15
–0.05
(10.0)
• Built-in stable sawtooth wave generator independent of
R1.8
0.6
• Built-in 50 Hz/60 Hz changeover circuit
2.54
1
1.45±0.15
3.5±0.3
• Minimum fly-back time of saw-tooth wave signal:
0.25 +0.10
–0.05
1.2±0.1
(12.5)
100 µs
(1.2)
1.80±0.15
■ Applications 19.1±0.3
21.9±0.3
• Televisions and CRT displays
HSIP012-P-0000A
Ramp
Vert. Vert. drive Vert. out
generator
trig.
input
11
12
1
9
VCC1 9 V
50 Hz/60 Hz SW
VCC2 26 V
GND
■ Pin Descriptions
Pin No. Description Pin No. Description
1 Power supply 1 7 Power supply 2
2 Vertical pulse input 8 Pulse amplification
3 Vertical amplitude control 9 GND
4 50 Hz/60 Hz changeover 10 Vertical output
5 Saw-tooth wave generation 11 Power supply for vertical output
6 AC/DC feedback input 12 Prevention from oscillation
2 SDB00020BEB
AN5534N
• Test method
1. Input threshold voltage (V2)
H2 voltage at which a saw-tooth wave shown below is generated at pin 5 when H2 voltage is gradually increased
from 0 V
2. Saw-tooth wave generating start voltage (V5)
Lower level voltage of a sawtooth wave which generates at pin 5
Input pulse of pin 2
H2
0V
L5
SDB00020BEB 3
AN5534N
■ Usage Notes
• Inter-pin short-circuit test result
6 ● ● ● ● ●
▲ ×
7 ▲ ● ● ▲ ●
8 ● ● ● ● ● ● ●
▲
9 ▲ ● ● ● ● ● ▲ ●
10 ● ● ● ● ● ● ● ● ×
×
11 ● ● ● ▲ × ● ● ● ▲ ●
▲
12 ● ● ● ● ● ● ● ● ● ● ●
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12
■ Technical Information
1. PD Ta curves of HSIP012-P-0000A
PD T a
50
45
40
35
Power dissipation PD (W)
30
Infinite heat sink: Rth (j−c) = 3°C/W
25
20
15
10
0
20 40 60 80 100 120 140 160
4 SDB00020BEB
AN5534N
1.0 s
1.0
0.1
0.01
10 60 100
VCE (V)
(ASO curve of deflection output Tr )
Note) The maximum value of deflection current for the actual use is suitable within ±1.5 A[0-p] (3 A[p-p]).
Ramp
Vert. Vert. drive Vert. out
generator
trig.
input
11
12
1
100 µF
VCC1 50 Hz/60 Hz VCC2
9V SW 26 V
50 Hz
47 µF D.Y.
47 µF 60 Hz
47 kΩ
0.68 µF
27 kΩ 18 kΩ 3.9 kΩ
Vert. 100 kΩ 33 kΩ 1 000 µF
trig. 1 µF
input 1.5 Ω
1.5 V Vert. height vol.
(0.5 W)
0V
SDB00020BEB 5
AN5534N
2.80±0.10
20.00±0.20
(0.60) )
1 8. 0
(R
7.70±0.20 6.40±0.20
12.40±0.30
21.90±0.30
21.90±0.30
(7.80)
(6.70)
1 12
3.50±0.20
29.60±0.20 1.80±0.15
6 SDB00020BEB
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.
2001 MAR