Transistor

2SD0601A (2SD601A)
Silicon NPN epitaxial planer type

For general amplification

Unit: mm
Complementary to 2SB0709A (2SB709A)
0.40+0.10
ñ0.05
0.16+0.10
-0.06

■ Features 3

1.50+0.25
-0.05
2.8+0.2
High foward current transfer ratio hFE.

-0.3
●

0.4±0.2
● Low collector to emitter saturation voltage VCE(sat).

5°
1 2
● Mini type package, allowing downsizing of the equipment and

(0.65)
(0.95) (0.95)
automatic insertion through the tape packing and the magazine 1.9±0.1
packing. 2.90+0.20
-0.05

10°

■ Absolute Maximum Ratings (Ta=25˚C)

1.1+0.2

1.1+0.3
-0.1

-0.1
Parameter Symbol Ratings Unit

0 to 0.1
Collector to base voltage VCBO 60 V
Collector to emitter voltage VCEO 50 V
Emitter to base voltage VEBO 7 V
Peak collector current ICP 200 mA 1:Base
2:Emitter EIAJ:SC–59
Collector current IC 100 mA
3:Collector Mini3-G1 Package
Collector power dissipation PC 200 mW
Junction temperature Tj 150 ˚C Marking symbol : Z
Storage temperature Tstg –55 ~ +150 ˚C

■ Electrical Characteristics (Ta=25˚C)

Parameter Symbol Conditions min typ max Unit
ICBO VCB = 20V, IE = 0 0.1 µA
Collector cutoff current
ICEO VCE = 10V, IB = 0 100 µA
Collector to base voltage VCBO IC = 10µA, IE = 0 60 V
Collector to emitter voltage VCEO IC = 2mA, IB = 0 50 V
Emitter to base voltage VEBO IE = 10µA, IC = 0 7 V
hFE1 * VCE = 10V, IC = 2mA 160 460
Forward current transfer ratio
hFE2 VCE = 2V, IC = 100mA 90
Collector to emitter saturation voltage VCE(sat) IC = 100mA, IB = 10mA 0.1 0.3 V
Transition frequency fT VCB = 10V, IE = –2mA, f = 200MHz 150 MHz
VCE = 10V, IC = 1mA, GV = 80dB
Noise voltage NV 110 mV
Rg = 100kΩ, Function = FLAT
Collector output capacitance Cob VCB = 10V, IE = 0, f = 1MHz 3.5 pF

*h Rank classification
FE1

Rank Q R S
hFE1 160 ~ 260 210 ~ 340 290 ~ 460
Note.) The Part number in the Parenthesis shows
Marking Symbol ZQ ZR ZS
conventional part number.

542
Transistor 2SD0601A

PC — Ta IC — VCE IB — VBE
240 60 1200
Ta=25˚C VCE=10V
Collector power dissipation PC (mW)

IB=160µA Ta=25˚C
200 50 1000

Collector current IC (mA)

140µA

Base current IB (µA)

160 40 120µA 800

100µA
120 30 600
80µA

80 20 60µA 400

40µA
40 10 200
20µA

0 0 0
0 20 40 60 80 100 120 140 160 0 2 4 6 8 10 0 0.2 0.4 0.6 0.8 1.0
Ambient temperature Ta (˚C) Collector to emitter voltage VCE (V) Base to emitter voltage VBE (V)

IC — VBE IC — I B VCE(sat) — IC
200 240 100

Collector to emitter saturation voltage VCE(sat) (V)

IC/IB=10
VCE=10V VCE=10V
Ta=25˚C
30
200
160
Collector current IC (mA)

Collector current IC (mA)

10

160
120 3

25˚C
120 1
Ta=75˚C –25˚C
80
0.3
80
25˚C
0.1 Ta=75˚C
40
40
–25˚C
0.03

0 0 0.01
0 0.4 0.8 1.2 1.6 2.0 0 200 400 600 800 1000 0.1 0.3 1 3 10 30 100
Base to emitter voltage VBE (V) Base current IB (µA) Collector current IC (mA)

hFE — IC fT — I E NV — IC
600 300 240
VCE=10V VCB=10V VCE=10V
Ta=25˚C GV=80dB
Forward current transfer ratio hFE

200 Function=FLAT
Transition frequency fT (MHz)

500
240 Ta=25˚C
Noise voltage NV (mV)

400 Ta=75˚C 160

180
25˚C
Rg=100kΩ
300 120
–25˚C
120
200 80
22kΩ

60 4.7kΩ
100 40

0 0 0
0.1 0.3 1 3 10 30 100 – 0.1 – 0.3 –1 –3 –10 –30 –100 10 30 100 300 1000
Collector current IC (mA) Emitter current IE (mA) Collector current IC (mA)

543
Request for your special attention and precautions in using the technical information
and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Govern-
ment if any of the products or technologies described in this material and controlled under the
"Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan.
(2) The technical information described in this material is limited to showing representative character-
istics and applied circuit examples of the products. It does not constitute the warranting of industrial
property, the granting of relative rights, or the granting of any license.
(3) The products described in this material are intended to be used for standard applications or gen-
eral electronic equipment (such as office equipment, communications equipment, measuring in-
struments and household appliances).
Consult our sales staff in advance for information on the following applications:
• Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment,
combustion equipment, life support systems and safety devices) in which exceptional quality and
reliability are required, or if the failure or malfunction of the products may directly jeopardize life or
harm the human body.
• Any applications other than the standard applications intended.
(4) The products and product specifications described in this material are subject to change without
notice for reasons of modification and/or improvement. At the final stage of your design, purchas-
ing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to
make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the guaranteed values, in particular those of maxi-
mum rating, the range of operating power supply voltage and heat radiation characteristics. Other-
wise, we will not be liable for any defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, redundant design is recommended,
so that such equipment may not violate relevant laws or regulations because of the function of our
products.
(6) When using products for which dry packing is required, observe the conditions (including shelf life
and after-unpacking standby time) agreed upon when specification sheets are individually exchanged.
(7) No part of this material may be reprinted or reproduced by any means without written permission
from our company.

Please read the following notes before using the datasheets

A. These materials are intended as a reference to assist customers with the selection of Panasonic
semiconductor products best suited to their applications.
Due to modification or other reasons, any information contained in this material, such as available
product types, technical data, and so on, is subject to change without notice.
Customers are advised to contact our semiconductor sales office and obtain the latest information
before starting precise technical research and/or purchasing activities.
B. Panasonic is endeavoring to continually improve the quality and reliability of these materials but
there is always the possibility that further rectifications will be required in the future. Therefore,
Panasonic will not assume any liability for any damages arising from any errors etc. that may ap-
pear in this material.
C. These materials are solely intended for a customer's individual use.
Therefore, without the prior written approval of Panasonic, any other use such as reproducing,
selling, or distributing this material to a third party, via the Internet or in any other way, is prohibited.

2001 MAR