Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

C6 Remove Fuel Pump

Download as pdf or txt
Download as pdf or txt
You are on page 1of 7

12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4979...

Page 1 of 7

Shutdown SIS

Previous Screen  
 
Product: MOTOR GRADER
Model: 12M MOTOR GRADER B9F00108
Configuration: 12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine
 
Disassembly and Assembly 
C6.6 Engines for Caterpillar Built Machines 
Media Number -KENR6081-12 Publication Date -01/06/2011 Date Updated -08/06/2011

   
i03083621

Fuel Injection Pump - Remove


SMCS - 1251-011 

Removal Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A (1)     9U-6198     Crankshaft Turning Tool     1    
9U-7336     Housing     1    
A (2)    
5P-7305  Engine Turning Tool     1    
B     230-6284     Timing Pin (Camshaft)     1    
136-4632     Timing Pin (Crankshaft)     1    
C    
268-1966  Adapter     1    
D     278-4138     Cap Kit     1    
( 1 ) 
Install Tooling to the front pulley.
( 2 ) 
Install Tooling into the aperture for the electric starting motor.

Start By: 

A. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and 
Install".

Note: Either Tooling (A) can be used. Use the Tooling that is most suitable. 

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2015
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4979... Page 2 of 7

Contact with high pressure fuel may cause fluid penetration and burn
hazards. High pressure fuel spray may cause a fire hazard. Failure to
follow these inspection, maintenance and service instructions may cause
personal injury or death.

NOTICE

Ensure that all adjustments and repairs that are carried out to the fuel
system are performed by authorised personnel that have the correct
training.

Before begining ANY work on the fuel system, refer to Operation and
Maintenance Manual, "General Hazard Information and High
Pressure Fuel Lines" for safety information.

Refer to Systems Operation, Testing and Adjusting Manual,


"Cleanliness of Fuel System Components" for detailed information on
the standards of cleanliness that must be observed during ALL work
on the fuel system.

NOTICE

Care must be taken to ensure that fluids are contained during


performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.

Dispose of all fluids according to local regulations and mandates.

Note: Put identification marks on all hoses, on all hose assemblies, on wires and on all tube 
assemblies for installation purposes. Plug all hose assemblies and tube assemblies. This helps to 
prevent fluid loss and this helps to keep contaminants from entering the system.

1. Turn the fuel supply to the OFF position.

2. Turn the battery disconnect switch to the OFF position.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2015
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4979... Page 3 of 7

3. If necessary, remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base 
- Remove and Install".

4. If necessary, remove the fuel priming pump. Refer to Disassembly and Assembly, "Fuel 
Priming Pump - Remove".

5. Use Tooling (A) in order to rotate the crankshaft so that number one piston is at top dead center 
on the compression stroke. Refer to System Operation, Testing and Adjusting, "Finding Top 
Centre Position for No.1 Piston".

6. Use Tooling (B) in order to lock the camshaft in the correct position. Use Tooling (C) in order 
to lock the crankshaft in the correct position. Refer to Disassembly and Assembly, "Gear Group 
(Front) - Remove" for the correct procedure.

7. Remove the backlash from the fuel pump gear. Lock the fuel injection pump in the correct 
position and remove the fuel pump gear. Refer to Disassembly and Assembly, "Fuel Pump Gear 
- Remove and Install" for the correct procedure.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2015
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4979... Page 4 of 7

Illustration 1 g01563275

Typical example

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2015
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4979... Page 5 of 7

Illustration 2 g01563276

Typical example

8. Disconnect plastic tube assembly (2) from fuel injection pump (1) .

9. Disconnect harness assembly (6) from solenoid (3) . Slide the locking tab into the unlocked 
position and disconnect harness assembly (6) from position sensor (7) .

Note: The harness assembly should be positioned in order to avoid an obstruction to the fuel 
injection pump.

10. Disconnect plastic tube assembly (10) from fuel injection pump (1) .

11. Disconnect plastic tube assembly (9) from fuel injection pump (1) .

12. Disconnect tube assembly (4) from fuel injection pump (1) .

13. Remove banjo bolt (13) and remove sealing washers (12) . Remove tube assembly (11) .

Note: In order to drain the fuel from the cylinder head, first disconnect tube assembly (11) at 
the fuel injection pump.

14. Plug or cap all open ports and tube assemblies immediately with new plugs or caps. 

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2015
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4979... Page 6 of 7

Note: Ensure that quick fit connections are clean before the tube assemblies are plugged.

15. Remove fuel injection line (5) . Refer to Disassembly and Assembly, "Fuel Injection Lines - 
Remove". Use Tooling (D) in order to plug the open ports in the fuel injection pump and in the 
fuel manifold. Discard the fuel injection line.

16. Remove tube assembly (8) for the engine oil supply to the fuel injection pump. Remove the 
banjo bolt and the sealing washers from the tube assembly.

Illustration 3 g01563333

Typical example

17. Remove bolts (15) and remove bolts (16) . Remove support bracket (14) .

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2015
12M Motor Grader B9F00001-UP (MACHINE) POWERED BY C6.6 Engine(SEBP4979... Page 7 of 7

Illustration 4 g01563853

Typical example

18. Remove bolts (18) and remove sealing washers (19) .

Note: The fuel injection pump should be supported by hand as the bolts are removed.

19. Carefully remove fuel injection pump (1) from front housing (20) . Ensure that bore (X) in the 
front housing is not damaged as the fuel injection pump is removed.

20. Remove O-ring seal (17) from fuel injection pump (1) .

Copyright 1993 - 2015 Caterpillar Inc.   Thu Dec 3 16:31:05 UTC+0800 2015
All Rights Reserved.
Private Network For SIS Licensees.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/... 12/3/2015

You might also like