Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 93 views

    Krishna Engineering College, Ghaziabad Department of Mechanical Engineering Machine Design-II Assignment No: 03

    Uploaded by

    Vivek Bajpai
    1. A pair of helical gears with a 35 degree helix angle is used to transmit 17 kW power at 12000 RPM. The pinion has 24 teeth and the face width is calculated as 12 times the module. The summary asks to determine the module and face width based on strength. 2. A pair of helical gears transmits 15 kW power. The pinion has 80 mm pitch diameter and runs at 10000 RPM. The gear has 320 mm pitch diameter. The summary asks to determine a suitable module and face width based on static strength. 3. Data is given for a pair of parallel helical gears transmitting 20 kW power at 720 RPM. The summary asks to calculate various parameters like helix

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Krishna Engineering College, Ghaziabad Department of Mechanical Engineering Machine Design-II Assignment No: 03

    Uploaded by

    Vivek Bajpai
    93 views2 pages
    1. A pair of helical gears with a 35 degree helix angle is used to transmit 17 kW power at 12000 RPM. The pinion has 24 teeth and the face width is calculated as 12 times the module. The summary asks to determine the module and face width based on strength. 2. A pair of helical gears transmits 15 kW power. The pinion has 80 mm pitch diameter and runs at 10000 RPM. The gear has 320 mm pitch diameter. The summary asks to determine a suitable module and face width based on static strength. 3. Data is given for a pair of parallel helical gears transmitting 20 kW power at 720 RPM. The summary asks to calculate various parameters like helix

    Original Title

    HELICAL GEARS (1)

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1. A pair of helical gears with a 35 degree helix angle is used to transmit 17 kW power at 12000 RPM. The pinion has 24 teeth and the face width is calculated as 12 times the module. The summary asks to determine the module and face width based on strength. 2. A pair of helical gears transmits 15 kW power. The pinion has 80 mm pitch diameter and runs at 10000 RPM. The gear has 320 mm pitch diameter. The summary asks to determine a suitable module and face width based on static strength. 3. Data is given for a pair of parallel helical gears transmitting 20 kW power at 720 RPM. The summary asks to calculate various parameters like helix

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    93 views2 pages

    Krishna Engineering College, Ghaziabad Department of Mechanical Engineering Machine Design-II Assignment No: 03

    Uploaded by

    Vivek Bajpai
    1. A pair of helical gears with a 35 degree helix angle is used to transmit 17 kW power at 12000 RPM. The pinion has 24 teeth and the face width is calculated as 12 times the module. The summary asks to determine the module and face width based on strength. 2. A pair of helical gears transmits 15 kW power. The pinion has 80 mm pitch diameter and runs at 10000 RPM. The gear has 320 mm pitch diameter. The summary asks to determine a suitable module and face width based on static strength. 3. Data is given for a pair of parallel helical gears transmitting 20 kW power at 720 RPM. The summary asks to calculate various parameters like helix

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    You are on page 1of 2

    Krishna Engineering College, Ghaziabad

    Department of Mechanical Engineering

    Machine Design- II
    Assignment No: 03
    UNIT:1 (Design of Spur & Helical Gear)

    Helical Gears
    1. A pair of helical gear with 35 degree helix angle is used to transmit 17 kW at 12000 RPM
    of the pinion. The velocity ratio is 5:1.Both the gears are made of hardened steel of static
    strength 120 MPa. The gears are 20 degree stub and the pinion is to have 24 teeth. The
    face width may be taken as 12 times the module. Find the module and the face width
    from the stand point of strength and check the gears for wear.[2017-18]

    2. A pair of helical gears is to transmit 15 kW. The teeth are 20° stub in diametric plane and
    have a helix angle of 45°. The pinion runs at 10 000 r.p.m. and has 80 mm pitch diameter.
    The gear has 320 mm pitch diameter. If the gears are made of cast steel having allowable
    static strength of 100 MPa; determine a suitable module and face width from static
    strength considerations and check the gears for wear, given σes = 618 MPa.[2016-
    17,2014-15]
    3. The following data is given for a pair of parallel helical gears made of steel :
    Power transmitted = 20 kW, np = 720 rpm, zp = 35, zg = 70, centre distance = 285 mm,
    normal module = 5 mm, b = 50 mm, normal pressure angle = 20°, S. = 600 N/mm2,
    surface hardness number = 300 BHN, grade of machining = 6, Service factor = 1.25
    Calculate:
    (a) The helix angle; (b) Beam strength, (c) Wear strength, (d) Static load, (e)The dynamic
    load by Buckingham's equation, (f) Effective factor of safety against bending failure.
    [2015-16]
    4. A pair of helical gears transmits 5 KW. The following are its details:
    Teeth on pinion & gear = 25 &50 Normal module =4 mm, helix angle=20 degree, normal pressure
    angle=20 degree. Determine the axial, tangential and radial components of the tooth load if pinion
    rotates at 1200 rpm.[2012-13]

    5. A herringbone speed reducer consists of a 26 teeth pinion driving a 104 teeth gear. The
    gears have normal module of 2 mm. The pressure and helix angle is 20 and 25 degree
    respectively. The pinion receives 100 KW power through its shaft and rotates at 3600
    rpm. The face width of each half is 35 mm. The gears are made of alloy steel 30NI4Cr1
    (Sut=1500 N/mm2) and heat treated to a surface hardness of 450 BHN. The service factor
    is 1.25.Determine the factor of safety against bending and pitting failure.

    6. A pair of herringbone gears is to transmit 15 kW. The teeth are 20° stub in diametral
    plane and have a helix angle of 45°. The pinion runs at 10 000 r.p.m. and has 80 mm
    pitch diameter. The gear has 320 mm pitch diameter. If the gears are made of cast steel
    having allowable static strength of 100 MPa; determine a suitable module and face width
    from static strength considerations and check the gears for wear, given σes = 618 MPa.

    You might also like