Shock and Vibration Testing

Vibration Lab Capabilities Overview Sheet
Shock and Vibration Testing

Vibration Lab Testing Services
• Sine frequency sweep with
constant displacement or
acceleration
Engineers know well the potential for mechanical vibration to compromise performance or cause
• Random with frequency failure. However, the details of vibratory environments are often not well understood, making it
weighted power spectral difficult to determine how to best simulate real world vibration in the laboratory. Various industry
density vibration testing standards may help, including the following for which Rexnord Innovation Center
• Shock with half-sine, haversine, (RIC) is accredited by the American Association for Laboratory Accreditation (A2LA) to perform.
triangular or saw-tooth pulses
• MIL-STD 810, METHOD 514 Sinusoidal Vibration
• Environmental conditions and
test procedures for airborne • MIL-STD 810, METHOD 516 Shock
equipment
• IEC 68-2-6 Sinusoidal Vibration
• Shock Response Spectrum
• IEC 68-2-64 Random Vibration
(SRS) with frequency weighted
spectral density • IEC 68-2-27 Shock
• Vibration testing of shipping
containers The experience and ingenuity of vibration experts at RIC can be instrumental to application of the
standards, effective fixturing methods and interpreting test results. We have capabilities ranging
• Combined sinusoidal vibration, from measuring vibration in actual use and analyzing designs for vibratory durability to
dry heat or cold
recommending a test plan, performing shock or vibration tests and recommending design changes.
• Temperature cycles combined
with sinusoidal or random Vibration testing at frequencies greater than 100 hertz requires the use of an electrodynamic shaker.
vibration Vibration testing of heavy samples at low frequencies may require use of a servo-hydraulic actuation.
• Military standard, mechanical Electrodynamic shakers at RIC:
vibrations of shipboard
equipment • From 100 to 7,200 pounds force
• Serving clients for more than • From 5 to 4,000 hertz
20 years
• Up to 3.5 inches peak to peak displacement
• Oil film slip table 36”x 36”
Servo-hydraulic systems:
• Up to 300,000 pounds force
• Up to 6 inches peak to peak displacement
Vibration testing may be combined with environmental testing:

• -100 degrees Fahrenheit (F) to 650 F
• 5% to 95% relative humidity
• 50 to 106 kPa (altitude)
Contact Information
Rexnord Innovation Center
5101 West Beloit Road
Milwaukee, WI 53214 (USA)
Phone: +1 414-643-3067
Fax: +1 414-643-3200
www.rexnord.com/InnovationCenter This laboratory is accredited by the American Association for Laboratory Accreditation (A2LA) and the
results shown in this test report have been determined in accordance with the laboratory’s terms of
Innovationcenter@rexnord.com
accreditation unless stated otherwise in this report. Testing Cert #0584-01
Vibration Lab Capabilities Overview Sheet
Mechanical shock and vibration

Your products may be required to meet rigorous military, electronic, industrial, or medical
device standards for resistance to shock and vibration prior to acceptance. Rexnord
can provide testing for product-specific test protocols over a wide range of amplitudes,
frequencies, and spectrums.
RIC utilizes well proven closed loop acceleration feedback control to simulate or recreate
almost any shock or vibration environment that your product may encounter. This includes
but goes well beyond industry and military vibration and shock testing methods established
by the International Electrotechnical Commission, Society of Automotive Engineers, United
States Military Standards (MIL-STD), and the Department of Defense.
Many products, however, are not covered by existing standards and you may require help
determining the best test practices to cost effectively provide the product reliability your
customers demand. Rexnord can help you to establish a logical shock and vibration test
protocol, run the tests and help in any resulting redesign activities.
If your test requires operational testing during vibration, Rexnord has expertise in
engineering monitoring systems to record operational functions such as electrical signals,
continuity, pressures, and temperatures. These signals can be fed back into the system to
record failures or stop the test.
Case study: Field measurement and vibration testing of electronic equipment

An aggregate processing machinery manufacturer wanted to know whether an electrical
cabinet would be able to withstand the vibrational loads sustained in the field. RIC engineers
traveled to the customer’s site and collected vibration data on the machine. They were then
able to replicate in the lab what was experienced during operation. Next, Rexnord accurately
predicted component failures, allowing for redesign before deployment of the equipment
into the field.
The RIC has eight electrodynamic shakers, ranging in capacity from 100 pounds force to
7,200 pounds force. Random, shock and drop, and wind milling tests are typical. We can also
perform “at altitude” tests in the environmental chamber while the shaker is running, saving
customers money as the equipment stays in its same location.
Customer Testimonial
“Excellent service and cost effective pricing … we always receive excellent service
from the Innovation Center … Thanks for all your support on our development
projects. “
— automotive lock manufacturer
Phone 414-643-3067 • www.rexnord.com/InnovationCenter
©2015 Rexnord RIC5-007 Printed in USA 02/15

Shock and Vibration Testing

Uploaded by

Copyright:

Available Formats

Shock and Vibration Testing

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Shock and Vibration Testing

Uploaded by

Copyright:

Available Formats

Vibration Lab Capabilities Overview Sheet

Shock and Vibration Testing

Vibration testing may be combined with environmental testing:

Mechanical shock and vibration

Case study: Field measurement and vibration testing of electronic equipment

Phone 414-643-3067 • www.rexnord.com/InnovationCenter

©2015 Rexnord RIC5-007 Printed in USA 02/15

You might also like