Heliyon 5 (2019) e02427

Contents lists available at ScienceDirect

Heliyon
journal homepage: www.heliyon.com

Synthesis and characterization of Argania spinosa (Argan oil) biodiesel by

sodium hydroxide catalyzed transesterification reaction as alternative for
petro-diesel in direct injection, compression ignition engines
Adewale Johnson Folayan *, Paul Apeye Lucky Anawe
Petroleum Engineering, Covenant University, Nigeria

A R T I C L E I N F O A B S T R A C T

Keywords: In this research work, the optimization conditions for obtaining optimum biodiesel yield from argan oil as well as
Chemical engineering the quantification of degree of interactions between reactants and biodiesel yield were investigated by using a
Argania spinosa response optimization model and response surface methodology (RSM) respectively. Similarly, a regression
Biodiesel
polynomial model was used to develop a unified equation for predicting the expected yield of Argan biodiesel for
Cold flow properties
Critical properties
different values of reactant variables and a regression coefficient of 92.56% was obtained.
Optimization model The Argan oil was extracted from its kernel by using a soxhlet extractor with hexane as extraction solvent and
Polynomial model 54.50% oil yield was obtained. The fatty acid compositional analysis was done by using a Shimadzu GCMS
RSM QP2010 SE Gas-chromatograph-mass spectrometer.
Transesterification reaction The spectrometer analysis shows that the oil has 80.90% of unsaturated fatty acid with oleic and linoleic acid
constituting larger percentages respectively. A sodium hydroxide catalyzed transesterification reaction was used
to convert the triglyceride in the oil to fatty acid methyl ester under standard conditions and the fuel properties of
the oil and its ester were measured by using the American society for testing and materials (ASTM) procedures. A
Fourier transform infrared spectroscopic (FTIR) technique was used for qualitative characterization of biodiesel
functional groups in order to affirm the complete conversion of the oil into biodiesel.
Results showed that the cold flow behaviour in terms of cloud point, pour point, cold filter plugging point
(CFPP) and Low temperature flow test (LTFT) and critical properties such as cetane number, calorific value, iodine
value, density, flash point, ash percentage and carbon residue of the Argan biodiesel showed a good agreement
with ASTM D6751-07b and European committee for standardization (EN 14214) standard requirements. Hence,
its application in compression ignition engines will pose no threat as far as performance, combustion and emission
qualities are concerned. Finally, the Argan biodiesel has a very high higher heating value (HHV) of 40,665 kJ/kg
which is very uncommon of other vegetable oils methyl esters and thus facilitate better heat release during
combustion and improves engine performance.

1. Introduction The process of finding alternative to diesel in compression-ignition

engines started with the direct use of plants oils either wholly or as
The insatiable desire for a green environment devoid of various forms blend with petroleum diesel without any major chemical and or physical
of environmental pollution coupled with the unsustainability and non- modification [1, 2].
renewable nature of fossil fuels has always been the impetus for exten- However, these plants oils were able to solve the environmental
sive search for a more environmentally benign and technically viable problems associated with the use of diesel in terms of its emission
alternative fuel from biomass in compression ignition engines. The characteristics but posed a huge technical problem in its performance and
American society for testing and materials defines biodiesel as fatty acid combustion characteristics. Notable among those technical issues are
methyl ester or mono alkyl esters of long chain fatty acids derived from abnormally high viscosity and density resulting in poor atomization and
vegetable oils (Plant Origin) or animal fats and other biomass derived oil combustion in the combustion chamber, injector coking, engine deposits
for use in compression-ignition (diesel) engines. and lubricant thickening which consequently lead to poor performance,

* Corresponding author.
E-mail address: folayanadewale03@yahoo.com (A.J. Folayan).

https://doi.org/10.1016/j.heliyon.2019.e02427
Received 25 February 2019; Received in revised form 21 May 2019; Accepted 3 September 2019
2405-8440/© 2019 The Author(s). Published by Elsevier Ltd. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-
nc-nd/4.0/).
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

higher exhaust emissions and reduced engine life [3, 4, 5, 6]. 1.1. Historical background of Argan oil
In order to annul these ugly scenarios, an insight into various methods
of chemically and or physically refining these plant oils prior to direct Argan oil is a plant oil that is extracted from the kernels of argan tree
usage as fuels began to emerge. Various methods of processing the plant fruit (Argania spinosa, family Sapotaceae) which is cultivated on a large
oils include thermal and catalytic cracking, electrolysis and the widely scale in Southwestern Morocco and covering areas such as Essaouira,
known transesterification reaction. Agadir, Chtouka Ait Baha, Tiznit and Taroudant [13]. The Argan tree is a
Transesterification involves the reaction of lower alcohols such as slow growing spiny tree with robust adaptation mechanisms for drought
methanol and ethanol, with higher vegetable oil fatty acids in the pres- and other harsh environmental conditions that are characteristic of South
ence of acidic or alkaline catalysts such as sodium hydroxide (NaOH) or Western Morocco [14]. In Morocco, the Argan forests cover about 8,
potassium hydroxide (KOH). The reaction products are fatty acid alkyl 280km2 and they are tagged as UNESCO biosphere reserves.
ester and glycerol. Edible Argan oil is not refined and it is obtained from slightly roasted
However, biodiesel yield and quality from transesterification reaction kernels whereas the non-edible (cosmetic grade oil) oil comes from non-
is dependent on a lot of factors. These are reaction time, type of alcohol roasted kernel [15]. Although Argan tree grows naturally exclusively in
and alcohol to oil molar ratio, reaction temperature and pressure, con- South Western Morocco, the kernels can also be exported to other
centration and type of catalyst, water content and free fatty acid level in countries for oil extraction and processing. The oil serves as source of
fats and oils. essential fatty acids and Vitamin E with extensive medicinal applications.
The industries embraced methanol as primary alcohol for biodiesel Argan oil share some similarities with olive oil and almond in the
synthesis regardless of its toxicity and chemical origin as a result of the following regards. They are cold-press oils, they are produced from a tree
following technical and economic advantages: fruit, they contain about 80% unsaturated fatty acid with oleic and
linoleic acid being the two major unsaturated fatty acid while palmitic
i. Very cheap and stearic acids form the two main saturated fatty acids in all the three
ii. Prevents soap formation oil samples [16, 17].
iii. High reactivity
iv. Easy method of recovery due to non-formation of azeotropes [7].
1.2. Seed processing and exraction of Argan oil

Various edible oils such as soybean oil, palm kernel oil and sunflower
The quality and properties of argan oil obtained from the argan nut is
oil are being widely used in commercial quantities as biomass feed stocks
dependent on two major factors, namely: extraction method and sec-
in united states of America, Argentina and Europe respectively. However,
ondly, processing and storage methodologies and conditions. There are
in order to forestall the eventual depletion of edible-oil supply worldwide
two methods of removing the argan kernels from the ripe fruits. Me-
arising from competition by biofuel demands, various non-edible oil
chanically cracked nuts provide us with an argan kernel of high quality
sources have been investigated by researchers. These include: Madhuca
oil in terms of composition, taste and shelf, whereas the traditional
indica, bitter Almond oil, Jatropha curcas, Karanja oil and Pongamia
method of goat-digested fruit yield kernels whose extracted oil has an
pinnata [8].
unacceptable chemical composition that is different from those of peeled
Abdelrahman et al 2019 [9] evaluated the viability of non-edible
fruit derived oil [18].
Radish seed oil (Raphanus sativus) as possible feed stock for bio-
For this research work, two (2) sacks, each of 50kg of argan kernels
diesel production. An oil yield of 33.50 wt.% was obtained by solvent
were mechanically pressed by a grinding machine to obtain pressed
extraction of the radish seed and an optimized base catalyzed trans-
cakes. The cakes were then taken into a soxhlet apparatus with hexane as
esterification of the oil with methanol, ethanol and mixed
solvent in order to extract the oil. The process was repeated in a number
methanol-ethanol yielded 95.55.wt.% of Fatty acid methyl esters
of times in order to obtain the required quantity of oil for the trans-
(FAMEs), 90.66wt.% of Fatty acid ethyl esters (FAEEs) and 93.33.wt.%
esterification process.
of Fatty acid methyl-ethyl esters (FAMEEs) respectively. The ultimate
conclusion was that the synthesized biodiesel corresponds to standard
limits requirement by ASTM D6751. 1.3. Oil yield
Similarly, the optimum conditions for transesterification of non-
edible Jatropha curcas seed oil for biodiesel production has been The percentage (%) of oil yield was calculated by using Eq. (1)
investigated by Dena et al 2018 [10]. Based on their findings, the op-
weight of oil obtained
timum operating conditions for Jatropha oil transesterification process Percentage Yield ¼  100
Weight of samples ðargan kernelsÞ
are methanol to oil molar ratio of 6:1, KOH catalyst concentration of 1%


by weight, reaction temperature of 60 C and duration of 60 min. An ester ¼ 54:5% (1)
yield of 94% was observed. Gupta et al 2016 [11] conducted an inves-
tigation into the biodiesel fuel properties of a mixture of edible and 2. Materials and methods
non-edible vegetable oil (thumba oil, karanja oil, linseed oil and palm
oil). A biodiesel yield of 97% that conforms with the stipulated biodiesel 2.1. Fatty acid compositional analysis of Argania spinosa (Argan oil)
quality standards was obtained with methanol to oil molar ratio of 8.8:1,


KOH catalyst concentration of 1.9g/100cc oil, temperature of 43.50 C After the extraction of the argan oil from the kernel, the composition of
and reaction time of 58.4 min. the fatty acids in the oil was determined by using Schimadzu Gas-
Fadhil and Mohammed 2018 [12] examined the biodiesel potential Chromatograph with mass spectrometer detector and the absolute values
characteristics of non-edible bitter almond oil by co-solvent trans- are presented in Table 1. We couldn't rely on the compositional informa-
esterification with hexane as solvent and potassium hydroxide catalyst tion that exist in the literature because of increasing degree of reported
(KOH) as alternative fuel to diesel in compression engines. It was re- cases of argan oil adulteration with olive oil [19, 20]. There are five (5)
ported that the properties of the biodiesel and its blends complied with essential components of the gas chromatography system. These are: the
the limits prescribed by ASTM D7467-17. column with the stationary phase, the carrier gas system, the split or
However, biodiesel production from ethanol route provides us with a splitless sample introduction system, GC detectors or the detection system
completely environmentally friendly fuel because of non-toxicity and and the computer station or integrator. The GC has a capillary column with
renewable nature of ethanol. an internal diameter (I.D) of 0.25mm. This diameter was selected because
it provides adequate plates per meter, allows acceptable sample capacity

2
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

Table 1
Fatty acids composition of Argania spinosa oil (Argan Oil) as determined from GC-MS analysis.
Fatty acid Molecular formular Molecular structure Structural formular % composition

Myristic C14 H28 O2 14:0 CH3(CH2)12COOH 0.08

Palmitic C16 H32 O2 16:0 CH3(CH2)14COOH 12.50
Palmitoleic C16 H30 O2 16:1 CH3(CH2)5CH ¼ CH(CH2)7 COOH 1.20
Stearic C18 H36 O2 18:0 CH3(CH2)16COOH 5.90
Oleic C18 H34 O2 18:1 CH3(CH2)7CH ¼ CH(CH2)7 COOH 43.60
Linoleic C18 H32 O2 18:2 CH3(CH2)4CH ¼ CHCH2 CH ¼ CH(CH2)7 COOH 35.80
Linolenic C18 H30 O2 18:3 CH3CH2CH ¼ CHCH2 CH ¼ CHCH2CH ¼ CH(CH2)7 COOH 0.30
Arachidic C20 H40 O2 20:0 CH3(CH2)18COOH 0.40
Behenic C22 H44 O2 22:0 CH3(CH2)20COOH 0.15

and lower ID gives higher capillary column efficiency. A film thickness of 2.3. Calculations
0.25μm was selected for sharper peaks, increase resolution and reduced
column bleed. While a column length of 30metres was chosen for better Argan oil free fatty acids (%) were calculated in terms of % oleic by
resolution balance, analysis time and required column head pressure. using Eq. (2).
Hence the column dimension was [30 m  0.25 mm x 0.25μm]. The sta-
tionary phase consists of chemically bonded, DB5-5% phenyl methyl sili- V  N  28:2
Free fatty acid ð%Þ ¼ (2)
cone. This was selected based on the polarity of Fatty acid and its methyl W
ester. The stationary phase is the most essential aspect of the capillary
where V ¼ volume in ml of standard sodium hydroxide solution used.
column because it determines selectivity and the column's ability to
N ¼ normality of standard sodium hydroxide solution used.
separate sample components. The Schimadzu, GC-2010 SE has oven

W ¼ mass(g) of oil sample used.
temperature and injector port temperature of up to 450 C with AFC
pressure range of zero to 970kpa. The mass spectrometer has a direct
2.4. Estimation of degree of unsaturation and long chain saturation factor
connection with capillary column and with temperature range of 50 to

for Argania spinosa (Argan oil)
350 C. The detector was a secondary electron multiplier with the patented
overdrive lens and conversion dynode. The injector temperature was set at



230 C while the oven temperature of the column was initially set at 100 C Total saturated fatty acid ¼ 19.03%
and held constant for 30s before it was increased to 150
C at the rate of


10 C/min and held for 5min. The column oven temperature was finally Total monounsaturated fatty acid (MUFA) ¼ 44.80%



increased to 220 C at the rate of 5 C/min and held for 5.50 min. About 5μL
Total polyunsaturated ¼ 36.10%
of heptane derivatized sample were injected into the GC-MS for separation
and analysis. The mobile phase (carrier gas) was helium and was pumped The total unsaturated Fatty Acid ¼ 80 90%
at a flow rate of 0.5 μL/min for 30 min (30). The difference between
chemical and physical properties of the injected sample and their in- Hence the degree of unsaturation ¼ MUFA þ 2PUFA ¼117
teractions with the stationary phase are the basis of the separation process.
The long chain saturation factor LCSF ¼ ð0:1 * wt% of C16
As the sample travels through the length of the column, separation of the
molecules occur as a result of different chemical properties of the mole- : 0Þ þ ð0:5 * wt% of C18 : 0Þ þ ð1 * wt % of C20
cules in the mixture and their affinity for the stationary phase. The mol- : 0Þ þ ð1:5 * wt % of C22 : 0Þ þ ð2:0 * wt% of C24 : 0Þ ¼ 4:825
ecules were retained in the column and eluted from the column at different
times called the retention time and this allows the mass spectrometer to
2.5. Transesterification reaction
capture, ionize, accelerate, deflect and detect the ionized molecules
separately. This was done by breaking each molecule into ionized frag-
Transesterification process was used to convert the triglyceride or
ments and detecting these fragments using their mass to charge ratio. The
triacylglycerol (TAG) present in Argan oil to methyl esters and glycerol
retention times identified by the gas chromatograph were then correlated
(propane 1,2,3 triol) using methanol in the presence of sodium hydroxide
by the computer to a spectrum library to see if its characteristics were
catalyst (NaOH) which helped to chemically breakdown the triglyceride
present for some samples in the library. Also, the compound can be
molecules in the vegetable oils, remove the glycerol chains from the
analyzed by measuring the peaks in relation to one another and the total
triglycerides and replace them with alkyl radicals from the methanol
mass of the unknown compound is normally indicated by the parent peak.
used. Various researchers [22, 23, 24] have opined that one of the best
This value of the parent peak can be used to fit with a chemical formula
conditions for the conversion of Fatty Acids to biodiesel are:
containing the various elements which are in the compound.
1 Catalyst total content of 1.5% for potassium hydroxide catalyst and
2.2. Determination of the percentage of free fatty acid of the Argan oil 1.0% for sodium hydroxide catalyst.
2 Methanol to Oil molar ratio of 6:1
The free fatty acid in the argan oil was determined by chemical 3 Reaction time of 2–3 h



titration method [21]. 4 Temperature range of 60 C-65 C
Fifty-six grams of well-mixed sample of each refined vegetable oil was
accurately measured into a 300ML Erlenmeyer flask. Also, 50ML of ethyl The schematic representation of the chemical reaction is shown in
alcohol (95% ethanol) containing 2ML of phenolphthalein indicator was Fig. 1.


heated to a temperature of 60 C by using water bath to prevent evapo-


ration because ethanol boils at 78 C. The mixture of hot, neutralized 2.5.1. Selection of suitable alcohol for the formation of alkoxide
ethanol was then added to the vegetable oil in the flask and titrated with The two major alcohols that are widely used in transesterification
0.1N sodium hydroxide solution (NaOH). The mixture was shaken reaction are methanol and ethanol. However, methanol was used in this
constantly until a pink colour which persisted for thirty seconds (30s) experiment because of its technical and economic advantages over
was observed in the alcohol layer above the sample. ethanol which includes less cost, prevention of soap formation, high

3
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

O O
|| ||
CH2 - O – C - R1 CH3 - O - C - R1
|
| O O CH2 - OH
| || || |
CH - O - C - R2 + 3 CH3OH → CH3 - O - C - R2 + CH - OH
| (NaOH Catalyst) |
| O O CH2 - OH
| || ||
CH2 - O - C - R3 CH3 - O - C - R3

Triglyceride Methanol Methyl Ester Glycerol

Fig. 1. Schematic representation of transesterification reaction.

reactivity, its recovery is easier because it does not form azeotropes and glycerol (propane 1,2,3 triol).
its short chain molecular size helps in the avoidance of steric hindrance
Reaction Mechanism
effect.
NaOH catalyst
Step 1 Triglycerides þ CH3 OH
→ Di  glycerides
2.6. Argania spinosa (Argan oil) biodiesel production process Temperature 65O C
þ Methyl ester
The various stages of producing Argania spinosa Biodiesel (ASB) via
(3)
alkali–catalyzed transesterification reaction can be summarized into a
Four-Stage production process under the following sub headings.
NaOH catalyst
Step 2 Di  glycerides þ CH3 OH
→ Monoglycerides
Temperature 65O C
2.6.1. Preparation of sodium methoxide solution
250 ml of methanol (analytical grade) was measured by using a þ Methyl ester
measuring cylinder and poured inside a 1000ml Erlenmeyer flask. The (4)
glass was capped with glass lid to prevent evaporation and 28.50gram of
Sodium Hydroxide (NaOH) pellets was measured by using a digital NaOH catalyst
Step 3 Monoglycerides þ CH3 OH
→ Methyl ester
weighing balance and was quickly added to the methanol thereby Temperature 65O C
minimizing its exposure to air. The alcohol-sodium hydroxide mixture
þ Glycerol
was stirred continuously with the aid of a magnetic stirrer until the
(5)
catalyst was completely dissolved in the alcohol to form sodium meth-


oxide solution. The solution was heated to a temperature of 50 C and
2.6.3. Fatty acid methyl Ester(FAME) and glycerol phase separation
maintained at this temperature which is below the boiling temperature of

After the completion of the transesterification reaction, the reaction
methanol (65 C).
mixture was immersed in a cold water bath and distilled water of about
15% of the initial volume of oil used (225ml) was added to the system
2.6.2. Main transesterification reaction
and the entire reaction mixture was re-stirred for thirty (30) minutes in
Because the free fatty acid content (FFA) of argan oil is 1.50 %, hence
order to prevent further reaction occurring as a result of unreacted
there was no need for acid esterification prior to the main trans-
catalyst and alcohol. At the end of 30 min, the reaction mixture was
esterification. For other vegetable oils such as coconut oil, with free fatty
transferred to a separating funnel and was allowed to settle for twelve
acid content above 2.0–2.5%, an acid transesterification is necessary as a
hours (12hrs) for the separation of the fatty acid methyl esters (FAME)
preliminary stage to reduce the level of Free Fatty Acid content (FFA)
and the glycerol layer under gravity. The mixture of the fatty acid methyl
before the main transesterification reaction [25].
ester was decanted into another beaker by opening the separating funnel
Hence, 1500ml of Argan oil was measured and placed in 5000ml

tap leaving behind the glycerol. As a result of different chemical affin-
Erlenmeyer flask and was heated to 65 C by using electric oven. While
ities, most of the catalyst and excess alcohol were concentrated in the
stirring the warmed oil, the sodium methoxide solution that was already

lower phase (glycerol) while most of the mono-, di- and tri-glycerides
prepared and maintained at 50 C was slowly added to avoid any possible
were concentrated in the upper phase (Methyl esters).
drop in the temperature of the reaction mixture. The solution became


cloudy. The reaction mixture was then heated to a temperature of 65 C
2.6.4. Purification of biodiesel
and continuously stirred with the aid of a magnetic stirrer which was
After the separation of glycerol, the Fatty acid methyl ester (FAME)
maintained at 500 revolutions per minute in order to increase mass
mixture contains impurities such as unreacted alcohol and catalyst,
transfer between the immiscible phases because alcohols and oils do not
mono-, di- and tri-glycerides. These impurities usually bring about un-
mix at room temperature. The reaction was left for 2 h to reach
desirable characteristics to the biodiesel produced. For instance,
completion.
increased cloud point and pour point and lower flash point. Hence the
The reaction mechanism has three main steps as shown in Eqs. (3),
mixture of FAME obtained from the alkali-catalyzed transesterification
(4), and (5). The first step involves an attack by the alkoxyde ion, to form
reaction must be purified in order to comply with established quality
a tetrahedrical intermediate. The second step involves the generation of
standards for biodiesel (ASTM and EN Standards) and for the following
alkoxyde by the reaction between the intermediate produced in the first
reasons.
step with an alcohol molecule. While in the last step, ester and di-
glycerides are produced with the liberation of three ester molecules and

4
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

1 Unreacted methanol must be removed because it degrades some Based on this model, the optimum conditions are sodium hydroxide
plastics and elastomers, very corrosive and can lower flash point to (NaOH) catalyst concentration of 1.08%, methanol to oil molar ratio of


unsafe levels (fire safety). 6:4, reaction time of 1.57hours and reaction temperature of 59 C with a
2 Unconverted or partly converted oils (bound glycerin) can result in response desirability of 0.9239. Similarly, a Response surface method-
very poor cold flow properties (Pour point, cloud point and Kinematic ology (RSM) was used to quantify the degree of interactions between the
Viscosity, injector and in-cylinder deposits and thus results in po- response or output variable (Biodiesel yield) and the input variables
tential engine failure. (catalyst concentration, methanol to oil molar ratio, temperature and
3 Free glycerin results in injector deposit, clogged fuel filters and un- time) and the surface response plots of these interactions are presented in
desirable deposits at the bottom of the fuel storage thank Figure 3a, b and c. A regression polynomial model was used to develop a
4 Unreacted catalyst (Caustic- NaOH) causes excessive injector, fuel unified equation (eq. 8) for predicting the expected yield of Argan bio-
pump wear, piston and ring wear, filter plugging and lubricant issues diesel for different values of reactant variables and a regression coeffi-
[26]. cient of 92.56% was obtained by plotting the experimental values against
the predicted yield (Fig. 4).
The volume of the biodiesel produced was measured after separation
from the glycerol layer to know the quantity of acidified and warm water Regression (polynomial) Model ¼ Y (yield) ¼ -414.644 þ 214.036X1
required. The methyl ester was washed with acidified water of about þ 26.755X2 þ 116.627X3 þ 7.115X4 – 98.765X21 -2.086X22 -37.044X23
20% of the produced ester volume in order to neutralize the mixture of – 0.060 X24 (8)
the esters. The acid-free ester was then washed with ordinary water and 2 2
R ¼ 92.56%, R (Adj) ¼ 84.06%
dried to produce a pure biodiesel.
where:
2.7. Conversion efficiency of the transesterification process X1 ¼ catalyst concentration (wt.%).
X2 ¼ alcohol to oil molar ratio.
The conversion efficiency of the biodiesel transesterification process X3 ¼ time (hour).

was deduced by using Eqs. (6) and (7) below. X4 ¼ temperature ( C).

 
Volume of FAME produced 2.9. FTIR Analyses
% yield of Fatty Acid Methyl Este ¼
Volume of Argan Oil used
 100 The presence of one or more aromatic rings in a structure is indicated
(6) by C–H and C¼C–C ring related vibrations. The C–H stretching group
occurs above 3000cm1 and it occurs as a multiplicity of weak to moderate
 
1240 bands compared with the aliphatic C–H stretch. In FTIR spectra, a well-
% yield of Biodiesel ¼  100 (7) defined absorption of one but typically two sets of bands with wave
1500
number in the region of 1615cm1-1495cm1 for aromatic ring stretch is
% yield of Biodiesel ¼ 82.67% representative of aromatic compounds [27]. This is conspicuously present
in diesel FTIR spectrum (Fig. 5c) but absent in the parent argan oil and its
produced biodiesel spectra (Fig.5a&b). This indicates the non-toxicity of
methyl esters (biodiesel). The diesel FTIR spectrum has an aromatic ring
2.8. Optimization of Argan oil biodiesel production parameters stretch in the region of 1604.84cm1-1460.73cm1 and an aromatic C–H
stretch of wave number 2954.09cm1 -2923.16 cm1 (Fig. 5c). From
A response optimization model (Fig. 2) was used to predict the Fig. 5b, the biodiesel has a methyl C–H asymmetrical stretch in the region
optimization conditions for obtaining an optimum yield of 88.85%. with group frequency of 2970cm1-2950cm1 while symmetrical stretch

Optimal Cat conc Alcohol Time Temp

D High 1,250 8,10 2,0 70,0
Cur [1,0833] [6,4030] [1,5707] [59,0404]
0,92392 Low 0,50 2,10 0,750 35,0

Composite
Desirability
0,92392

Yield
Maximum
y = 88,8589
d = 0,92392

Fig. 2. Response optimization Model.

5
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

occurs between 1470cm1 and 1430cm1 with a symmetrical bend in the

region of 1380–1370cm1. Also, the Argan oil fatty acid methyl ester has a
characteristics vibration group frequency in the region between 1750cm1
and 1725cm1. This shows a qualitative conversion of the triglycerides in
the vegetable oil to fatty acid methyl ester.

3. Results and discussion

(1) Cold flow properties: The cold flow properties of vegetable oil and
its alkyl ester (biodiesel) is an intrinsic characteristics of the degree of
saturation and branching of its fatty acid.

(a) Cloud Point:

The cloud point is the temperature at which wax crystals begin
to form in a liquid as it is cooled. It can also be seen as the tem-
perature at which an oil starts to solidify. Knowing the cloud point
is very essential in determining storage ability of the fuel because
storing formulations at temperature significantly higher than the
cloud point may result in phase separation and instability [28].


The argan oil has a cloud point of 8 C (Table 2), this makes the
argan oil to be susceptible to start up and performance problems
when the compression engine and the fuel system are subjected to
cold temperatures because at temperatures below the cloud point,
larger crystals fuse together and form large globules that can
restrict or cut off flow through fuel lines and filters [29, 30, 31].


Upon transesterification, the cloud point decreased to -3 C
(Table 4) which makes its application in cold climate less prob-
lematic. However, when the biodiesel was blended with cold flow
improver at ratios B30 ; B50 and B80 , there was a significant
improvement in the cloud point as seen in Table (8). It must be
noted that when operating an engine at temperatures below its
cloud point, heating will be necessary in order to avoid waxing of
the fuel.
(b) Pour Point:
Pour point represents the lowest temperature at which a liquid


will began to flow. The argan oil has a pour point of 5 C. Hence,
the high pour point results in extensive crystal agglomeration
which prevents free pouring of fluid under cold temperature
conditions. Whereas, the synthesized biodiesel has a pour point of


-7 C (Table 4) which invariably means that little stresses are
needed to be overcome before the fuel begins to flow. Meanwhile,
Fig. 3. a: Surface response plot for Yield (%) with catalyst concentration and
blending with petro diesel cold flow improver, tremendously
alcohol to oil molar ratio interactions. b: Surface response plot for Yield (%)
with reaction Temperature and Time interactions. c: Surface response plot for
reduced the pour point to -14, -19 and -31 for the three blends of
Yield (%) with reaction Time and Catalyst concentration interactions. B30 ; B50 and B80 respectively (Table 8).
(c) Cold Filter Plugging Point (CFPP) and Low Temperature Flow Test
(LTFT)
90.00 The cloud point and pour point are relatively easy to measure,
but the CP over-estimate the cold temperature limit at which start
y = 0.9256x + 5.0307
80.00
up or performance issues begin to occur in a fuel system whereas
R² = 0.9256
the pour point tends to be optimistic [32, 33].
The CFPP describes the lowest temperature at which a 20-ML
Experimental value

70.00
sample of a liquid passes through a 45-μm wire mesh under
0.0194 atm vacuum within 60s. While the low temperature flow
60.00 test (LTFT) is the lowest temperature at which 180-ML sample of
Argania spinosa (Argan oil) or its methyl ester passes through a
50.00 17-μm wire mesh filter under 0.197atm vacuum within 60s.The
Argan oil has a relatively high CFPP and LTFT (Table 2), hence,
40.00 higher susceptibility to filter plugging and flow operational
problems are inevitable in cold temperature climates. This is
because when wax molecules in the oil tends to crystallize at low
30.00
temperatures, crystals agglomerate to form large masses which
40 50 60 70 80 90
invariably causes filter plugging and eventually solidify the oil.
Predicted value
However, a remarkable improvement in these properties was seen
Fig. 4. Experimental versus predicted values from polynomial model. in the Argania spinosa biodiesel and upon blending with petro-
diesel.
Summarily, the synthesized Argan biodiesel has better cold flow

6
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

Fig. 5. a: Argan oil FTIR spectrum. b: Argan oil Methyl ester FTIR spectrum. c: Diesel FTIR spectrum.

7
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

Table 2 Table 4
Cold flow properties of Argania spinosa Oil. Cold flow properties of Argania spinosa biodiesel.
Fuel property Method of estimation Result Fuel property Method of estimation Result



Cloud Point ( C) ASTM D2500 8 Cloud Point ( C) ASTM D2500 -3



Pour Point ( C) ASTM D97 5 Pour Point ( C) ASTM D97 -7



CFPP ( C) ASTM D6371 4.5 CFPP ( C) ASTM D6371 -6



LTFT ( C) ASTM D4539 10 LTFT ( C) ASTM D4539 -2.5

properties than the Jatropha and Olive oil biofuels because of its value of 4.76mm2 =s at 40 C for canola oil methyl ester. Lower
higher degree of unsaturation. According to Eboibi et al 2018 kinematic viscosity was experienced with Argan oil biodiesel
[34], Jatropha curcas methyl ester (biodiesel) has a cloud point of because viscosity increases with chain length and degree of



8 C and pour point of 2 C (Table 6). While methanol unsaturation of the fatty acid [42, 43].
trans-esterified olive oil under optimum conditions has a cloud (c) Flash Point:



point of -2 C and pour point of -3 C [35]. The flash point is the lowest temperature at which a liquid can
form an ignitable mixture in air near the surface of the liquid. Both
(2) Critical properties: These are properties that directly affect the the argan oil and its methyl ester (biodiesel) have a relatively high
performance, combustion and emission characteristic of the compression flash point that is comparable with that of Jatropha oil biodiesel of


ignition engines upon the application of a designated fuel. 162 C [44] and within the lower limit requirements by ASTM and
EN standards (Table 3). Low flash point has its detriment in cold
(a) Specific Gravity: weather starting. However, minimum flash point temperatures are


The argan oil biodiesel has a specific gravity of 0.865 at 15 C required for proper safety and handling of the fuel.
which is in good agreement with standard requirements. This (d) Iodine Value:
density is high enough to increase energy concentration of fuel The iodine value is a scale to numerically quantify the degree of
and thus minimize fuel leakage and enhance fuel atomization ef- unsaturation of fats and oil. From Table 1, the Argan oil has a high
ficiency [36, 37]. Whereas the un-trans-esterified argan oil has an degree of unsaturation of 117 and hence, a higher iodine value of
ignominious density of 910 kg/m3 at the same temperature which 105gI2/100g of oil. Whereas, the Argan oil biodiesel has an iodine
corresponds to higher viscosity that results in poor combustion, value of 101 gI2/100g of biodiesel. All these values fall within the
performance and emission characteristics. In comparison of the acceptable standard limits and thus make the biodiesel an efficient
Argan oil biodiesel to those of commercially available biodiesel fuel due to high combustion rate and reduced oxidation and
fuels, Pradeep and Sharma 2007 [38] evaluated the fuel char- polymerization.
acteristics of Jatropha oil biodiesel and a density of 878 kg/m3 For methanol transesterification of Jatropha oil using NaOH
was obtained. These lower densities will ultimately give room for catalyst, Raja et al 2011 [45] obtained an iodine value of 101.7
better air-fuel ratio and improvement of fuel atomization gI2/100g of biodiesel because of similar fatty acid profile. Also,
efficiency. Abdur Rahman et al 2010 [46] recorded iodine values of 101.67
(b) Kinematic Viscosity.: gI2/100g of biodiesel for KOH catalyzed methanol trans-esterified
Kinematic viscosity is both cold flow and critical property of oil sunflower oil. Iodine value significantly influences fuel oxidation
to be used in compression engines and it represents the degree of and the type of aging products and deposits formed in diesel en-
resistance to flow offer by the fluid. The argan oil has an extremely gine injectors. It has a relation with oxidative stability and reflects


high viscosity of 33.15mm2 =s at 40 C (Table 3) which violates the the tendencies of a fuel to oxidize and polymerize to form engine
ASTM and EN standard requirement for oil to serve as replace- deposits.
ment for diesel in CI engines. This makes the oil to be susceptible (e) Cetane number:
to poor combustion, increased exhaust smoke and emissions when The cetane number is a dimensionless descriptor of the ignition
used directly as fuel in direct injection, CI engines. Upon trans- quality of a fuel and it a measure of the interval between the
esterification, the Argania spinosa biodiesel yielded a kinematic beginning of injection and auto-ignition of the fuel. Improper in-


viscosity value of 3.68 mm2 =s at 40 C(Table 3) which invariably jection timing and consequent engine locking is the common ca-
conforms with the standard requirement of 1.9–6.0 and 3.5–5.0 tastrophe associated with fuels that have low cetane number [47].
for ASTM D6751 and EN14214 respectively. This sufficiently The Argania spinosa oil has a cetane number of 52.50 which is in
lower viscosity would help to prevent problems such as injector agreement with ASTM D6751 minimum value of 47 but violates
coking, poor fuel atomization, carbon deposits on piston and en- the EN14214 minimum requirement of 51. Conversely, the Argan
gine head, excessive engine wear and increased exhaust smoke biodiesel has a cetane number of 54.20 which is good enough to
and emission [39]. Whereas corn oil biodiesel has a higher kine- forestall operational problems associated with poor ignition


matic viscosity value of 5.9 mm2 =s at 40 C [40] than Argan methyl quality. Interestingly, the Argan biodiesel has a higher cetane


ester of 3.68 mm2 =sat 40 C. Avella et al 1992 [41] also recorded a number than the soybean and sunflower biodiesel (Tables 5 and

Table 3
Critical properties of Argania spinosa (argan oil).
Test property Test method Test result ASTM D6751 standard EN 14214 standard


Kinematic viscosity @ 40 C(mm2 = sÞ ASTM D445 33.15 1.9–6.0 3.5–5.0


Specific Gravity @ 15 C ASTM D1298 0.910 0.88 0.86–0.90


Flash Point ( C) ASTM D93 164 93 min. 120 min
Cetane Number ASTM D613 52.50 47 min. 51 min
Calorific Value kj= ASTM D240 39,310 Sufficiently close to diesel 35 mj/kg
kg
gI2 ASTM D445 105 Report 130 max
Iodine Value
100g of oil

8
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

Table 5
Critical properties of Argania spinosa (argan oil) biodiesel.
Test property Test method Test result ASTM D6751 standard EN 14214 standard


Kinematic viscosity @ 40 C(mm = sÞ
2 ASTM D445 3.68 1.9–6.0 3.5–5.0


Specific Gravity @ 15 C ASTM D1298 0.865 0.88 0.86–0.90


Flash Point ( C) ASTM D93 148 93 min. 120 min
Cetane Number ASTM D613 54.20 47 min. 51 min
Calorific Value kj= ASTM D240 40,665 Sufficiently close to diesel 35 MJ/kg
kg
gI2 ASTM D445 101 Report 130 max
Iodine Value
100g of biodiesel

Table 6
Comparison of physico-chemical properties of plant oil methyl esters.
Plant oil Property





K.V@40 C (mm2/s) Cetane number H.V (Mj/kg) Flash point ( C) Cloud point ( C) Pour point ( C)

Coconut[56a, 56b] 2.83 70 36.1 110 0 -3

Palmkernel[57a, 57b] 4.839 54.57 38.6 167 6 2
Soyabean [48] 4.18 49.6 39.823 190.6 -1.1 -3.9
Corn [40] 5.9 49 35.4 212 -2 -16
Olive [35] 4.7 61 37.29 110 -2 -3
Canola [41] 4.76 47.9 39.87 166 -3 -9
Jatropha [34, 44] 4.84 51.6 37.2 162 8 2
Sunflower oil [49, 62] 4.2 50 38.2 177 5 -2

Table 7
Less critical properties of Argania spinosa (argan oil) Biodiesel.
Test property Test method Test result ASTM D6751 standard EN 14214 standard

Sulphated Ash(%) ASTM D 874 0.0095 0.020 max 0.020 max

Carbon residue (100% sample) ASTM D 4530 0.038 0.050 max 0.30 for 10% dist res
Free Glycerin (%) ASTM D6584 0.0085 0.020 max 0.020 max
Total glycerin (%) ASTM D6584 0.115 0.240max 0.250 max
Water and sediment (%) ASTM D2709 0.015 0.050 max 0.050 max

6). According to Yahyah and Marley 2004 [48], the cetane (3) Less critical properties: The synthesized biodiesel has a low per-
number of soybean oil methyl ester was 49.6. While Maria et al centage of ash content of 0.0095 and carbon residue of 0.038% (Table 7).
2009 [49] obtained a value of 50 for sun flower oil biodiesel These values are very healthy as they help to prevent issues such as
(Table 6). injector tip plugging, combustion deposits and injection system wears. A
Argan oil has a higher cetane value because of the presence of more than 0.02% sulphated ash indicates the presence of residual soap
more saturated fatty acids in its profile (Table 1). Sunflower oil and catalyst. Sulphated ash in biodiesel can occur as a result of abrasive
has about 59% polyunsaturated linoleic acid and 30% mono- solids, unremoved catalysts and presence of soluble metallic soap [59].
unsaturated oleic with only 11% saturated fatty acids. Similarly, High carbon deposits can invariably lead to fuel injector fouling and
soybean oil has 61% poly unsaturated fatty acid and 23.4% cylinder scoring within an engine. Free and total glycerine of the syn-
monounsaturated fatty acid [50]. thesized Argan biodiesel were evaluated by using ASTM D6584 proced-
If cetane number is too high, combustion can occur before the ures. The total glycerin quantifies the glycerol, mono, di and triglycerides
fuel and air are properly mixed resulting in incomplete combus- present in the biodiesel and if it is too high, catastrophes such as fuel filter
tion and smoke. Whereas, low cetane number results in engine plugging and instability may arise. The free glycerin and total glycerin
roughness, misfiring, higher air temperatures and slower engine fall within the standard acceptable limit as seen in Table 7. For methanol
warm up [51]. trans-esterified Jatropha oil using NaOH catalyst, Folaranmi 2013 [60]
(f) Calorific Value: recorded a free glycerine value of 0.05% and a total glycerine value of
The calorific value refers to the amount of heating energy 0.32%. Similarly, the free and total glycerine values obtained from the
released by the burning of a unit mass of fuel. Both the argan oil methanolysis of sunflower oil are 0.004 and 0.22% [61]. High total
and its methyl ester (Biodiesel) have a very interesting heating glycerine is an insignia of incomplete trans-esterification reaction and
value of 39,310 kJ/kg (Table 3) and 40,665 kJ/kg (Table 5) thus leads to production of crystals and deposits. Similarly, the water
respectively. These values are sufficiently close to that of diesel of sediment was found to be 0.015% which is good for the synthesized
45,310 kJ/kg [52]. Higher calorific value is desired for fuel biodiesel because excess free water in biodiesel can induce corrosion of
because it facilitates the heat release during combustion and im- fuel injection parts, appearance of free fatty acids and bacteria growths
proves engine performance [53, 54, 55]. However, for methanol
transesterification of coconut oil using potassium hydroxide
(KOH) catalyst, Bello et al 2015[56a] obtained a lower calorific Table 8
value of 36.1 MJ/kg (Table 6). Also, for palm kernel oil methyl Cold flow properties of blends.
ester, a calorific value of 38.6 MJ/kg was obtained by Igbokwe Fuel property B30 B50 B80
and Obiukwu 2013[57b] (Table 6). Biodiesel heating value in-

Cloud Point ( C) -9 -15 -24
creases with increase in carbon number in the ester molecule as

Pour Point ( C) -14 -19 -31
well as with increasing ratio of carbon to hydrogen atoms [58].

CFPP ( C) -12 -16 -27


LTFT ( C) -8 -13 -21

9
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

that eventually clog filters. Acknowledgements

4. Conclusion The authors are very grateful to Chancellor of Covenant University

and the university management team for their support in providing
The viability of Argania spinosa (Argan oil) biodiesel produced research enabling environment and condition.
through alkali-catalyzed transesterification reaction as possible alterna-
tive to diesel fuel in compression ignition engines has been investigated References
via robust experimentation and analysis.
[1] P.K. Gupta, R. Kumar, B.S. Panesar, V.K. Thapar, Parametric studies on bio- diesel
Alkali-catalyzed transesterification reaction is a reliable process
prepared from rice bran oil, Agric. Eng. Int.: GIGR J. Sci. Res. Dev. 9 (2007). EE 06-
which can help to bring about desirable properties on plant oils. For 007.
instance, the Argan oil specific gravity, kinematic viscosity, and iodine [2] M.C. Math, Performance of a diesel engine with blends of restaurant waste oil
value were reduced by 4.95%, 88.90% and 3.81% respectively to methyl ester and diesel fuel, Energy Sustain. Dev. 11 (3) (2007) 93–95.
[3] T.W. Ryan, T.J. Callahan, L.G. Dodge, Characterization of vegetable oils for use as
conform to standard requirement. while an increase of 3.24% and 3.45% fuel in diesel engines, Proc. International Conference on Plaint Oils as Fuels, Am.
in cetane number and calorific value respectively was observed on Soc. Agric. Eng. 4 (82) (1982) 70–81.
transesterification. While the argan oil has an abysmal viscosity of [4] S. Bari, C.W. Yu, T.H. Lim, Performance deterioration and durability issues while

running a diesel engine with crude palm oil, Proc. I Mech E Part D, J. Automobile
33.15mm2 =s at 40 C that can make it to be susceptible to poor combus- Eng. 216 (2002) 785–792.
tion, increased exhaust smoke and emissions when used directly as fuel in [5] O.J. Alamu, M.A. Waheed, S.O. Jekayinfa, Biodiesel production from Nigerian palm
direct injection, CI engines. Whereas the its biodiesel has a low viscosity kernel oil: effect of KOH concentration on yield, Energy Sustain. Dev. 11 (3) (2007)

77–82.
value of 3.68 mm2 =sat 40 C which gives room for reduced exhaust smoke [6] S. Saravanan, G. Nagarajan, G.L.N. Rao, S. Sampath, Feasibility study of crude rice
emission, good fuel atomization and low engine wear. The biodiesel has a bran oil as a diesel substitute in a DI-CI engine without modifications, Energy
very good higher heating value of 40,665 kJ/kg which is very uncommon Sustain. Dev. 11 (3) (2007) 83–95.
[7] I.A. Musa, The effect of alcohol to oil molar ratios and the type of alcohol on
of other vegetable oils methyl esters and thus facilitate better heat release biodiesel production using transesterification process, Egyptian J. Petrol. 25 (1)
during combustion and improves engine performance. However, the (2016) 21–31.
Argan oil has abnormal cold flow properties that threatens its application [8] M. Ahmad, M.A. Khan, Z. Muhammad, S. Shazia, in: Marco Aurelio Dos Santos,
Bernardes (Eds.), Biodiesel from Non Edible Oil Seeds: A Renewable Source of
in cold climates but the synthesized biodiesel has good cold flow prop-
Bioenergy, Economic Effects of Biofuel Production, 2011. InTech. Available from:
erties which can be improved upon by addition of petro-diesel cold flow http://www.intechopen.com/books/economic-effects-of-biofuel-production/bio
improver. Also, cetane number of 52.50 and 54.20 were obtained from diesel-from-non-edible-oil-seedsa-renewable-source-of-bioenergy.
[9] B.,F. Abdelrahman, H.S. Saba, N.M.T. Al-Layla, Transesterification of non-edible
the extracted oil and its biodiesel respectively. These values are sufficient
seed oil for biodiesel production: characterization and analysis of biodiesel, Energy
enough for good ignition quality. Meanwhile, the amount of ash, carbon Sources, Part A Recovery, Util. Environ. Eff. 41 (7) (2019) 892–901.
deposit, total glycerine and water sediment in the biodiesel showed that [10] A.K. Dena, A.F. Hassan, K.A. Nevine, A.Z. Ahmed, M.A. Rehab, Smart utilization of
the fuel is free of any unreacted catalyst, soaps and glycerol and thus Jatropha (Jatropha curcas Linnaeus) seeds for biodiesel production: optimization
and mechanism, Ind. Crops Prod. 111 (2018) (2018) 407–413.
prevent issues such as injector plugging, injector fouling, filter plugging [11] J. Gupta, A. Madhu, A.K. Dalai, Optimization of biodiesel production from mixture
and corrosion of injector parts respectively. of edible and non-edible vegetable oils, Biocatal. Agric. Biotechnol. 8 (2016) (2016)
Finally, from the results obtained, it can be concluded that the syn- 112–120.
[12] A.B. Fadhil, H.M. Mohammed, Co-solvent transesterification of bitter almond oil
thesized Argan biodiesel sufficiently fulfilled the upper and lower limits into biodiesel: optimization of variables and characterization of biodiesel, Transport
requirements of biodiesel by both the American society for testing and 33 (3) (2018) 686–698.
materials (ASTM) and the European union biodiesel standards. [13] M. Farines, J. Soulier, M. Charrouf, R. Soulier, Etude de l’huile des graines
d’Argania spinose (L) (Sapotaceae. I). la fraction glyceridique, Rev. Fr. Corps Gras
[ZDB]. 31 (1984) 283–286.
Declarations [14] Z. Charrouf, G. Dominique, Argan oil, occurrence, composition and impact on
human health, Eur. J. Lipid Sci. Technol. 110 (2008) 632–636.
[15] H. Hicham, G. Said, G. Dominique, C. Zoubida, Effect of argan kernel storage
Author contribution statement conditions on argan oil quality, Eur. J. Lipid Sci. Technol. 112 (2010) 915–920.
[16] V. Dubois, S. Breton, M. Linder, J. Fanni, M. Parmentia, Fatty acid profiles of 80
A. J. Folayan: Performed the experiments; Analyzed and interpreted vegetable oils with regard to their nutritional potential, Eur. J. Lipid Sci. Technol.
109 (2007) 710–732.
the data; Wrote the paper. [17] I. Kazantzis, G.D. Nanos, G.G. Stravroulakis, Effect of harvest time and storage
P. A. L., Anawe: Concieved and designed the experiments; Contrib- conditions on almond kernel oil and sugar composition, J. Sci. Food Agric. 83
uted reagents, materials, analysis tools or data. (2003) 354–359.
[18] Z. Charrouf, H. El Hamchi, S. Mallia, G. Licitra, D. Guillaume, Influence of roasting
and seed collection on argan oil odorant composition, Nat. Prod. Commun. 1 (2006)
Funding statement 399–404.
[19] A. Qussama, F. Elabadi, O. Devos, Analysis of argan oil adulteration using infrared
spectroscopy, Spectrosc. Lett. 11–15 (2012).
This work was supported by Covenant University, Ota, Nigeria. [20] S. Addou, F. Fethi, M. Chikri, A. Rrhiousa, Detection of argan oil adulteration with
olive oil using fluorescence spectroscopy and chemometrics tools, J. Mater.
Environ. Sci. 7 (8) (2016) 2689–2698.
Competing interest statement [21] AOAC, Official Methods of Analysis, 15TH edition, 69–84, Association of official
analytical chemists. AOAC pub. Virginia, USA, 1990, pp. 951–979.
The authors declare no conflict of interest. [22] J.M. Encinar, J.F. Gonzalez, A. Rodriguez-Reinares, Ethanolysis of used frying oil
biodiesel preparation and characterization, Fuel Process. Technol. 88 (5) (2007)
513–522.
Additional information [23] M.M. Al Naggar, F.H. Ashour, R.S. Ettouney, M.A. El Rifai, Production of biodiesel
from locally available spent vegetable oil, J. Renew. Energy Sustain. Dev. 3 (2)
(2017) 189–195.
No additional information is available for this paper. [24] P.A.L. Anawe, J.A. Folayan, Data on optimization of production parameters on
persea americana (avocado) plant oil biodiesel yield and quality, Data in Brief 20
(2018a) 855–863.
Data availability statement [25] A.V. Tomasevic, S.,S. Siler-marinkovic, Methanolysis of used frying oil, Fuel
Process. Technol. 81 (2003) 1–6.
The authors can boldly say that all the data used in this study were [26] Alternative Fuels Consortium, An Overview of ASTM D675: Biodiesel Standards and
Testing Methods, Rachel Burton Central Carolina Community College, Piedmont
obtained from rigorous experimental research in the laboratory and not Biofuels, 2008.
from any journal either in print or on line. We also declare that the data
will be available for public use once the paper is published.

10
A.J. Folayan, P.A.L. Anawe Heliyon 5 (2019) e02427

[27] J. Coates, Interpretation of infrared spectra, a practical approach,”, in: R.A. Meyers annuus L) oil and waste cooking oil, Energy Explor. Exploit. 28 (6) (2010)
(Ed.), Encyclopedia of Analytical Chemistry, John Wiley & Sons Ltd, Chichester, 499–512.
2000, pp. 10815–10837. [47] F.A. Uriate, Biofuels from Plant Oils: A Book for Practitioners and Professionals
[28] P.A.L. Anawe, J.A. Folayan, Novel synthetic based drilling fluid through enzymatic Involved in Biofuels, to Promote a Better and More Accurate Understanding of the
inter-esterification of canola oil, Int. J. Chem. Eng. (2018b), 6418090. Hindawi. Nature, Production and Use of Biofuels from Plant Oils, National Academy of
[29] J. Zielinski, F. Rossi, Wax and Flow in diesel fuels, in: Proceedings of SAE Science and Technology. Government of Japan. Japan ASEAN Solidarity Fund,
International Fuels and Lubricants Meeting and Exposition. Paper No.841352, 2010.
Society of Automotive Engineers, Warrendale, PA, 1984, 1984. [48] A. Yahya, S.J. Marley, Physical and chemical characterization of methyl soy oil and
[30] K. Lewtas, R.D. Tack, D.H.M. Beiny, J.W. Mullin, Wax crystallization in diesel fuel: methyl tallow esters as CI engine fuels, Biomass Bioenergy 6 (1994) 321–328.
habit modification and the growth of n-alkane crystals, in: Adavances in Industrial [49] J.,R. Maria, M.,F. Carmen, C. Abraham, R. Lourdes, P. Angel, Influence of fatty acid
Crystallization, Butterworth-Heineman Oxford, 1991, pp. 166–179. composition of raw materials on biodiesel properties, Bioresour. Technol. 100
[31] J.E. Chandler, F.G. Horneck, G.I. Brown, The effect of cold flow additives on low (2009) (2009) 261–268.
temperature operability of diesel fuels, in: Proceedings of SAE International Fuels [50] E. Akbar, Z. Yaakob, S.K. Kamarudin, M. Ismail, J. Salimot, Characteristics
and Lubricants Meeting and Exposition. Paper No.922186, Society of Automotive composition of Jatropha Curcas oil seed from Malaysia and its potential as biodiesel
Engineers, Warrendale, PA, 1992, 1992. feed stock, Eur. J. Sci. Res. 29 (3) (2009) 396–403.
[32] M.L. McMillan, E.G. Barry, Fuel and vehicle effects on low temperature operation of [51] G. Knothe, J.V. Gerpen, J. Krahl, The Biodiesel Hand Book, AOCS PRESS, Urbana,
diesel vehicles: the 1981 CRC field test, in: Proceedings of SAE International Fuels Illinois, 2004, pp. 76–80.
and Lubricants Meeting and Exposition. Paper No.830594, Society of Automotive [52] P.A.L. Anawe, J.A. Folayan, Data on physico-chemical, performance, combustion
Engineers, Warrendale, PA, 1983, 1992. and emission characteristics of persea americana biodiesel yield and its blends on
[33] D.J. Rickeard, S.J. Cartwright, J.E. Chandler, The impact of ambient conditions, fuel direct injection, compression ignition engines, Data in Brief 21 (2018) (2018)
characteristics and fuel additives on fuel consumption of diesel vehicles, in: 1533–1540.
Proceedings of SAE International Fuels and Lubricants Meeting and Exposition. [53] H.T.C. Machacon, S. Shiga, T. Karasawa, H. Nakamura, Performance, emission
Paper No.912332, Society of Automotive Engineers, Warrendale, PA, 1992, 1992. characteristics of a diesel engine fueled with coconut oil-diesel fuel blend, Biomass
[34] B.E. Eboibi, O. Eboibi, J. Okputu, K.A. Okpohwo, Production and analysis of Bioenergy 20 (2001) 63–69.
biodiesel from Jatropha curcas seed, J. Appl. Sci. Environ. Manag. 22 (1) (2018) [54] S. Bari, T.H. Lim, C.W. Yu, Effects of preheating of crude palm oil (CPO) on injection
26–33. system, performance and emission of a diesel engine, Renew. Energy 27 (2002)
[35] A. Serdari, K. Fragioudakis, S. Kalligeros, S. Stournas, E. Lois, Impact of using 339–351.
biodiesel of different origin and additives on the performance of a stationary diesel [55] S.C.A. De-Almeida, C.R. Belchior, M.V.G. Nascimento, L.D.S.R. Vieira, G. Fleury,
engine, J. Eng. Gas Turbines Power 122 (2000) 624–631. Performance of a diesel generator fueled with palm oil, Fuel 81 (2002) 2097–2102.
[36] E. Alptekin, M. Canakci, Characterization of the key fuel properties of methyl ester [56] [a] E.I. Bello, I.T. Adekanbi, F.O. Akinbode, Production and characterization of
biodiesel-diesel fuel blends, Renew. Energy 33 (2008) 2623–2630. coconut (Cocos nucifera) oil and its methyl ester, Eur. J. Eng. Technol. 3 (3) (2015)
[37] S.B. Lee, K.H. Han, J.D. Lee, I.K. Hong, Optimum process and energy density 25–34;
analysis of canola oil biodiesel synthesis, J. Ind. Eng. Chem. 16 (2010) 1006–1010. [b] N.A. Musa, G.M. Teran, A.Y. Saraki, Characterization of coconut oil and its
[38] V. Pradeep, R.P. Sharma, Use of HOT EGR for NOx control in a compression ignition biodiesel, J. Sci. Res. Rep. 9 (6) (2016) 1–6.
engine fueled with biodiesel from Jatropha Oil, Renew. Energy 32 (2007) (2007) [57] [a] O.J. Alamu, T.A. Akinola, C.C. Enweremadu, A.E. Adeleke, Characterization of
1136–1154. Palm kernel oil biodiesel produced through NaOH-catalyzed transesterification
[39] H.J. Harwood, Oleochemicals as a fuel. Mechanical and economic feasibility, process, Sci. Res. Essays 3 (7) (2008) 308–311;
JAOCS (J. Am. Oil Chem. Soc.) 61 (1984) 315–324. [b] J.O. Igbokwe, O.O. Obiukwu, Performance characteristics of a diesel engine
[40] N.A. Khan, H. Dessouky, Biodiesel production from corn oil by transesterification fueled with palm kernel methyl ester and its blend with petro-diesel, Pacific J. Sci.
reaction process, The Nucleus 46 (3) (2009) 241–252. Technol. 14 (2) (2013) 75–79.
[41] F. Avella, A. Galtieri, A. Fiumara, Characteristics and utilization of vegetable [58] A. Demirbas, Calculation of higher heating values of biomass fuels, Fuel 76 (5)
derivatives as diesels, Riv. Combust. 46 (1992) 181–188. (1997) 431–434.
[42] G. Knothe, Dependence of biodiesel fuel properties on the structure of fatty acid [59] J.A. Folayan, P.A.L. Anawe, A.O. Ayeni, Synthesis and characterization of Salicornia
alkyl esters, Fuel Process. Technol. 86 (2005) (2005a) 1059–1070. bigelovii and Salicornia brachiate halophytic plants oil extracted by supercritical
[43] G. Knothe, K.,R. Steidley, Kinematic viscosity of biodiesel fuel components and CO2 modified with ethanol for biodiesel production via enzymatic
related compounds: influence of compound structure and comparison to petro- transesterification reaction using immobilized Candida Antarctica lipase catalyst in
diesel fuel components, Fuel 84 (9) (2005b) 1059–1065. tert-butyl alcohol(TBA) solvent, Cogent Eng. (2019), 1625847.
[44] R.K. Singh, K.P. Saroj, Characterization of Jatropha oil for the preparation of [60] J. Folaranmi, Production of biodiesel (B100) from Jatropha oil using sodium
biodiesel, Nat. Product. Radiance 8 (2) (2009) 127–139. hydroxide as catalyst, J. Petrol. Eng. (2013), 956479. Hindawi Publishers.
[45] S.A. Raja, D.S. Robinson-smart, C.L. Robert Lee, Biodiesel production from Jatropha [61] R.P. Estelvina, A.C. Araceli, C.C. Arturo, R.R. Rubi, Qualitative Characteristics of
oil and its characterization, Res. J. Chem. Sci. 1 (1) (2011) 81–87. Biodiesel Obtained from sunflower Oil; Biofuel Status and Perspective, INTECH
[46] S. Abdur Rahman, A.B. Kafadar, Y. Tonbul, C. Kaya, F. Aydin, C. Hamamci, OPEN, 2015.
Comparison of the biodiesel quality produced from refined sunflower (Helianthus [62] B.R. Moser, Influence of blending canola, palm, soybean and sunflower oil methyl
esters on fuel properties of Biodiesel, Energy Fuels 22 (6) (2008) 4301–4306.

11