BRASSCATALOG.

COM
Fittings, Valves, Clamps & Accessories for Hose, Pipe and Tube

PRODUCT CATEGORIES

WWW.BRASSCATALOG.COM
 BRASS FITTINGS PIPE

PIPE

BRASS
WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
Pi p e Si z e 1/16 1/8 1/4 3/8 1/2 3/4 1
Th r e a d Si z e 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-111/2
Working
1200 1200 1200 1200 1200 1000 1000
Pr e s s u r e
T h r e a d OD 1/4 3/8 1/2 5/8 3/4 1 1-1/4

•Typical Application • “L” at the end of a Part# means Light Pattern

Grease, fuels, LP and Natural gas (available on special - these fittings are completely interchangeable with
order), refrigeration, instrumentation and hydraulic systems. full pattern fittings, but have been modified in some
way. This modification is usually in the length of the
•Pressure pipe threads. Used in plumbing and light industrial
Operating pressure up to 1200 PSI. applications.

•Vibration •Assembly Instructions

Fair resistance. 1- Tighten approximately 2-1/2 turns past hand tight.
2- Fittings with Everseal tighten two turns past hand
•Temperature Range tight. Brittle materials require special cautions.
-650F to +2500F (-530C to +1210C).
• see page 409-412 for hydraulic pipe steel
fittings.
•Used With
Brass, bronze, copper, steel, aluminum and iron pipe.
• see page 295-297 for plastic pipe fittings.
• Tolerance
+/- .02 on all dimensions. Dimension Data can change
without notice. Please call us when dimensions are critical. • Lead Free Fittings
see pages 158-160
• For Bronze & Larger Sizes
• Conformance
see pages 223-231
Meets specifications and standards of ASA, ASME and SAE

• Not lead free

* For larger sizes, see bronze fittings on
pg. 220-227
Actual outside diameters of pipe threads
www.P65Warnings.ca.gov

Actual Male Thread Profiles

1
 HOSE BARB BRASS FITTINGS

HOSE BARB FITTINGS

BRASS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
• Temperature and Working Pressure Ranges • For Lead Free AB1953 Compliant Fittings
From -400F to + 1600F at 150 PSI maximum. see pages 160--161
Other Barbs available
• Tolerance See page 292-295 for plastic hose barb fittings
+/- .02 on all dimensions. Dimension Data can change
without notice. Please call us when dimensions are criti- See page 27-28 for stainless steel hose barbs
cal.
See page 307 for King Nipples
Note: These fittings are intended for use with hose clamp,
similar type clamp or a crimped ferrule. Stainless Steel hose barbs for beverage service
available -
• Assembly Instructions See beverage fitting section, pg. 28-29
1- Cut hose cleanly and squarely to length.
2- Slide clamp on hose.
3- Lubricate hose. Push hose on fitting until hose bot-
toms against stop ring or hex.
4- Position hose clamp as shown below and secure
with a screwdriver or wrench. Maintain “A” dimen-

sion noted below for proper clamp positioning. 

      
     
      
     
     
www.P65Warnings.ca.gov

     
     

Actual Profile of Hose Barbs

1/2"
3/8"
5/16"
1/4"
3/16"
1/8" 5/8" 3/4" 1"

.165 .227 .29 .354 .415 .53 .645 .79 1.02

14
 PUSH ON HOSE BARB BRASS FITTINGS

PUSH ON BARB FITTINGS

BRASS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
Typical Application: Low Pressure Air, Fuel, Lube, and • Disassembling Instructions
Oil Lines 1- Split hose. Do not cut completely through hose.
• Pressure determined by tube material and hardness.Our Sealing edge of barb could be damaged.
Parts have been tested to max 150 PSI. 2- Bend hose and remove with a quick pull.
Advantages: Easy assembly. No clamps needed!!
• Assembly Instructions See lead free section for lead free push-on barb fittings.
1- Lubricate insert. Stainless steel available at the end of this section.
2- Hold hose at angle as shown & push on and up over
first barb.
3- Continue to push straight on until hose is seated under
protective plastic cap. Keep hands back from hose end
area so that hose can expand.

Actual Profile of Push On Barbs

.7 2 5 . 85
.60
www.P65Warnings.ca.gov

. 3 4 5 . 41 . 47

1 /4 " 5 /1 6 " 3 /8 " 1 /2 " 5 /8 " 3 /4 "

30
 BRASS FITTINGS GARDEN HOSE

GARDEN HOSE FITTINGS

BRASS
WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
• Temperature and Working Pressure Ranges

From +350F to +1000F at 75 PSI maximum or

the recommended working pressure of the gar- Male Garden Hose Profile
den hose. (Not to exceed 150 PSI.)
See Plastic section for
Note: All female connector ends should Plastic Garden Hose Fittings
have a rubber washer inserted prior to
usage. See page 162 for lead free Garden Hose

FGH = Female Garden Hose threads Washers included are #30150B black rubber
MGH = Male Garden Hose threads washers.
Male garden hose threads are all 3/4” with an
outside diameter of 1.0625 and 11-1/2” threads
per inch.

Actual Profile of Garden Hose Barbs

.79 1.02
.645
www.P65Warnings.ca.gov

.53
.415

37
 BRASS FITTINGS SAE 45° FLARE

SAE 45° FLARE

BRASS
WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more
Tube
1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4
O.D.
Thread
5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 11/16-16 3/4-16 7/8-14 1-1/16-14
Size-B
•Typical Application
LP and natural gas, flammable liquids,
• Tolerance
instrumentation, refrigeration, power
+/- .03 on all dimensions. Dimension data can change
steering, hydraulic and pneumatic systems.
without notice. Please call us when dimensions are criti-
cal.
•Working Pressure Ranges
Temperature and type of tubing used are important
•Conformance
factors. However, the following table is a good
Meets specifications and standards of ASA, ASME,
guide for proper selection. Temperature 730F with
SAE and MS (Military standards).
copper tubing:
Assembly Instructions
1- Cut tubing to desired length. Make sure all burrs
PSI Tube O.D. (in.) Tube Wall (in.) are removed and ends are cut square.
2800 1/8 .030
2- Slide nut on tube. Threaded end “A” of nut must
1900 3/16 .030
1400 1/4 .030
face out.
1200 5/16 .032 3- Flare end of tube with a 450 flaring tool.
1000 3/8 .032 a-Measure flare diameter.
750 1/2 .032
b- Examine flare for excessive thin out.
650 5/8 .035
550 3/4 .035
4- Lubricate threads and assemble to fitting body. Nut
450 7/8 .035 should be turned hand tight.

information, visit www.P65Warnings.ca.gov

5- Tighten assembly with wrench until a solid feeling
is encountered. From that point, apply a one-sixth
•Vibration turn.
Good resistance - use long nut when greater Note: Do not over-torque as it may damage the
vibration resistance is required. fitting or split the tubing at the flare.
•Temperature Range
-650F to +2500F (-530C to +1210C) range at maxi-
mum operating pressures.
• See Lead Free Flare Fittings page 163-164
•Used With
Copper, brass, aluminum and steel hydraulic tub-
ing that can be flared.
Actual O.D. of Flare Fittings

49
 INVERTED FLARES BRASS FITTINGS

INVERTED FLARE
BRASS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
Tube
1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8 1
O.D.
Thread TO.D.
hread
28
5/16-28 3/8-24 7/16-24 1/2-20 5/8-18 11/16-18 3/4-18 7/8-18 1-1/16-16 1-3/16-16 1-5/16-16
Sizinch
threads per e-B

•Typical Application •Conformance

Hydraulic brake, power steering, fuel lines and transmis- Meets specifications and standards of ASA, ASME, SAE and
sion cooler lines, LP and natural gas. MS (Military Standards).

•Working Pressure Ranges •Assembly Instructions

Temperature and type of tubing used are important factors. 1-Cut tubing to desired length. Make sure all burrs are
However, the following table is a good guide for proper removed and the ends are cut square.
selection. Temperature 730F with copper tubing: 2- Slide nut on tube. Threaded end “A” of nut must face out.
3- Flare end of tube with a 450 flaring tool.
                     a- Measure flare diameter.
      b- Examine flare for excessive thin out.
       c- On thin wall, welded or brazed tubing, use double flare
to prevent pinch-off and cracked flares.
     
4- Lubricate threads and assemble to fitting body. Nut
       should be turned hand tight.
      5- Tighten assembly with wrench until a solid feeling is
encountered. From that point, apply a one-sixth turn.
     
      Note: Do not over-torque as it may damage the fitting or split
the tubing at the flare.
     

•Vibration
Excellent resistance.

•Temperature Range
-650F to +2500F (-530C to +1210C) range at maxi- STANDARD METRIC THREADS
mum operating pressures. Description Thread Crest Thread
Tube Size O.D. (Pitch) Description
•Used With
Copper, brass, aluminum and steel hydraulic tubing Japanese 3/16" 10mm 1.0mm M10 x 1.0
that can be flared. European 3/16" 10mm 1.0mm M10 x 1.0
GM 6mm 12mm 1.0mm M12 x 1.0
www.P65Warnings.ca.gov

•Advantages
Very low cost and reusable. Seats and threads are Fuel 5/16" 14mm 1.5mm M14 x 1.5
internal and protected. Compact, excellent vibration Fuel 3/8? 16mm 1.5mm M16 x 1.5
life. Short nut affords very close tube bends. Steel or
brass tube nut. Measuring Metric Threads: Measure the O.D. of the threads
and the crest to crest distance (pitch) in millimeters between
• Tolerance threads.
+/- .03 on all dimensions.
Actual O.D. of male inverted flare threads
28

68
 COMPRESSION BRASS FITTINGS

COMPRESSION FITTINGS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
BRASS

These are NOT Lead Free

See pages 164-166 for Lead Free products

Tube O.D. 1/8 3/16 1/4 5/16 3/8 7/16 1/2 5/8 3/4 7/8
Thread Size-B 5/16-24 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 11/16-20 13/16-18 1-18 1-1/8-18
Working Pressure 400 400 300 300 200 200 200 150 100 75

• Typical Application • Conformance

Use with copper, aluminum and thermoplastic tub- Meets specifications and standards of ASA, ASME and
ing. Not recommended for steel tubing. Manufactured SAE.
for low and medium pressure tubing connection work
where excessive vibration or tube movement is not •Assembly Instructions
involved. Not recommended for application using gas- 1- Cut tubing to desired length.
eous media. 2- Slide nut and then sleeve on tube. Threaded end
“A” of nut must face toward fitting.
•Pressure 3- Insert tubing into fitting body. Be sure tubing is
See table above for working pressures at 73oF. bottomed on fitting shoulder.
4- Lubricate threads and assemble nut to fitting body.
•Vibration 5- Tighten nut hand tight. From that point, tighten
Fair resistance - use long nut when greater vibration with a wrench the number of turns indicated in the
resistance is needed. chart below.

•Temperature Range
-65oF to +250oF (-53oC to +121oC) range at maximum
Tube Size Additional Turns from
operating pressures. (Refer to tubing temperature
Hand Tight
range.)
1/8" thru 1/4" 1-1/4"
•Used With 5/16" 1-3/4"
Aluminum, copper, brass and plastic tubing. Plastic tub- 3/8" thru 1" 2-1/4"
ing requires insert. Not recommended for steel tubing.
www.P65Warnings.ca.gov

• “L” at the end of a Part# means Light Pattern -These

fittings are completely interchangeable with full pattern
• Tolerance fittings, but have been modified in some way. This
+/- .02 on all dimensions. Dimension data can change modification is usually in the length of the pipe threads.
without notice. Please call us when dimensions are Used in plumbing and light industrial applications.
critical.

Actual Profile of Compression Threads

76
 FLARELESS BRASS FITTINGS

Flareless
BRASS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
Flareless Brass Tube Fittings are Interchangeable with
Poly-Flo®, Poly-Tite® and Poly-Line® and Poly-Fit®

Built-in SS
Tube Support

Tube O.D. 1/8 3/16 1/4 5/16 3/8 1/2

Thread Size-B 5/16-24 3/8-24 3/8-24 7/16-24 1/2-24 11/16-20

•Typical Application •Advantages

Pneumatic instrumentation circuits, lubricant and cooling No flaring of tubing required. Easy installation, captive
lines. sleeve, pre-assembled for installation and can be reas-
sembled. Nuts rotate around the sleeve during tightening,
•Working Pressure and Temperature Ranges preventing twisting of tubing.
Up to 150 PSI from 0oF to + 150oF with thermoplastic
tubing. Up to 300 PSI from 0oF to + 175oF with soft •Assembly Instructions
metal tubing. 1- Cut tubing to desired length.
2- Slide nut/sleeve assembly on tube. Threaded end
•Maximum allowable metal tube wall thickness for use “A” of nut must face toward fitting.
with Poly-Tite fittings: 3- Bottom tubing into fitting.
1/8”, 3/16” O.D. --no limitation, 4- Plastic sleeve - Tighten nut hand tight.
1/4” O.D.--.035 5/16”, 3/8”,1/2” O.D.--.049 Brass Sleeve - Tighten nut hand tight, then an
additional 3/4 turn.
•Vibration
Excellent Resistance. * Note: 1/8 and 3/16 sizes have brass sleeves
•Temperature Range
Depends on tubing used. -65oF to +250oF
(-53oC to +121oC) with brass sleeve, -40oF to +150oF
(-40oC to +66oC) with plastic sleeve. (Refer to tubing
temperature range.)
www.P65Warnings.ca.gov

•Used With
Aluminum & copper tubing. Hard plastic tubing requires
brass sleeve. Not recommended for steel tubing.

• Tolerance
+/- .02 on all dimensions. Dimension data can change
without notice. Please call us when dimensions are criti-
cal.

90
 BRASS PUSH-IN FITTINGS BRASS FITTINGS

BRASS PUSH-IN FITTINGS

BRASS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
ENGINEERING AND DESIGN
• QUICK CONNECT, simply push tubing in, no tools. Saves up to 75% When tubing (1) is inserted
of assembly time of standard compression fittings. into the fitting, it first passes
1
• QUICK DISCONNECT, hold two fingers on insert and pull tubing through the gripping teeth
out, no tools required. 4 (2). Just beyond the gripping
• REUSEABLE, connect and disconnect numerous times. teeth is the o-ring (3) which
2
3 provides the leak proof seal
• FULL FLOW DESIGN, provides up to 60% more flow area than con-
5 against the OD of the tube.
ventional fittings with internal tube supports.
The gripping teeth grab the
• POSITIVE SEAL, no leaks. After tubing is inserted, seal is made.
tube, which
• VERSATILE, BunaN “O” rings standard. Other materials of “O” rings expands the insert. Pulling back on the tube only tightens
available. the grip as the insert moves onto the camming surface (4).
• SECURE TUBE RETENTION, pulling on tubing only serves to Pressure through the tube also serves to tighten the grip.
tighten the connection. The tube bottoms against a positive tube stop (5) in a cav-
• SELF CONTAINED ASSEMBLY, no loose parts, brass body and ity providing tube support to prevent leakage.
insert.
• BRASS CONSTRUCTION, elbows and tees are forged brass.
• CHOICE of convenient swivel of economical stationary elbows and tees.
• STRAIGHT CONNECTORS have interior hex for Allen key tightening where space is limited...no need to use a wrench.
• PRE-APPLIED TEFLON ® based pipe sealant on all male pipe threads, saving customer additional labor.
• METRIC SIZES AVAILABLE: Metric tube sizes from 2mm through 12mm in both standard NPT and metric pipe sizes are avail-
able on a special order basis.
www.P65Warnings.ca.gov

• WORKING TEMPERATURE:
-100F to 2000F (other ranges available on request).
• PIPE THREAD: NPTF with Teflon ® based sealant pre-applied.
• Tolerance
+/- .02 on all dimensions. Dimension data
can change without notice. Please call us when
dimensions are critical

96
 NICKEL PLATED PUSH-IN FITTINGS BRASS FITTINGS

NICKEL PLATED PUSH-IN FITTINGS

BRASS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
with GLOBAL THREAD
• NPTF • BSPP • BSPT • ISO 7 • ISO 228 • G THREAD • J THREAD

• Saves time and money • Completely reusable

• No stripped threads • Quick installation
• No stripped parts • No pitch identification
• Reduce inventory

Component Parts and Materials

Body Brass - Nickel Plated
• Tolerance
Thrust Ring Acetalic Resin/ Glass filled Nylon +/- .02 on all dimensions. Dimension data
Sleeve Brass - Nickel Plated can change without notice. Please call us when
Gripper Collet Stainless Steel dimensions are critical.
Safety Ring PA66
Lip Seal ( 1/8 O-Ring Seal) NBR 70
Thread Seal NBR 70
GLOBAL THREAD
Works With Inch or Metric Threads
Max Operating Pressure: Vacuum to 290PSI.
Min Temperature: -4°F
“Global Thread” fittings can be
Max Temperature: 176°F
www.P65Warnings.ca.gov

Tubing: Nylon, Polyethylene, Polyurethane. assembled with female threads

GLOBAL THREAD
- For best results use 95 Durometer produced to the following stan-
NPT • BSPT • RC • NPTF • BSPP • G

Media: Compressed air, water, vacuum dards: Tapered NPTF

Parrallel (BSPP, BSP, ISO 7)
Tapered (BSPT, PT, ISO 7, ISO 228)

102
 BRASS FITTINGS COMPOSITE BODY PUSH-IN FITTINGS

Composite Body Push-In Fittings

BRASS
WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
• For Food Grade,
see page 298-299

Specifications The latest generation of composite material is used in the

Fluid admitted Air body construction in addition to brass on threaded com-
Working pressure range 0-150 PSI (10BAR) ponents and stainless steel on the tube gripper.
Min. Burst pressure 340PSI (23BAR)
• Tolerance
Working Temperature range 0°F ~160°F
+/- .02 on all dimensions. Dimension data
can change without notice. Please call us when
dimensions are critical.
Materials of Construction:
1 Body Composite Polyacetal
(hemopolymer,copolymer)
2 Body Brass
3 Tube Release Acetal Resin
4 Retainer Brass
5 Gripper Ring Stainless Steel
6 Spacer Brass
7 O-Ring NBR 70
8 Threads Brass w/ white sealant
www.P65Warnings.ca.gov

111
 BRASS FITTINGS D.O.T. PUSH-IN
D.O.T. PUSH-IN TUBE FITTINGS

BRASS
WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
Meets D.O.T. FMVSS 571.106 SAE J1131 Air Brake System Requirements

Benefits for Cost Savings & Engineering Project DOT Fittings are constructed with an all brass captive
• Fast assembly: No tools required. Simply push tubing in. eyelet which allows for maximum flow. The brass
Saves up to 75% of assembly time compared to standard air captive eyelet with extended length is floating and has a
compression fittings. No loose parts to handle. machined top end radius for easy installation of tubing.
• Fast disconnect: Hold the collet collar with two fingers and All male threads have a pre-applied Teflon® based pipe
pull out tube. No tools required. sealant to provide for easy assembly and leak proof seal.
• Reusable: Can be connected and disconnected several times.
• Reliable sealing: Using recommended tubing, full sealing is
guaranteed. • Materials:
• Versatility: Buna N O'ring standard. Viton and others avail- Brass
able per request. Secure tube retention. Pulling on tubing "O" Ring: Buna - Nitrile (90 Durometer)
only serves to tighten the connection. EP (Ethylene Propylene)
• Pre-Applied Teflon® based pipe sealant on all male pipe
threads, saving customer additional labor. • Working Pressures & Temperature Ranges
• Full Flow Design, provides more flow area than conventional Vacuum to 150 PSI
fittings with internal tube supports even in the swivels. -40°F to 200° F ( -40°C to +93°C )
www.P65Warnings.ca.gov

Dimension data can change without notice. Please see our

website when dimensions are critical.

119
 COMPOSITE BODY D.O.T. PUSH-IN BRASS FITTINGS
COMPOSITE BODY DOT AIRBRAKE FITTINGS
BRASS

BRASS
WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
WARNING
• Composite DOT push-to-connect fittings are designed only for use in applications
where air is utilized as an operating fluid.

• Fittings must be used in accordance with manufacturer and industry specifications.

• They are not intended for use in environments exceeding 145psi or 140 degrees F.

• The Department of Transportation FMVSS 49CFR571-106 prohibits use of this type of

fitting for connections between towed and towing vehicles or between a driveshaft and
chassis.

• Using Composite DOT fittings in a manner inconsistent with manufacturer specifica-

tions may result in serious injury or property damage.

• Under no circumstances shall the supplier be liable to buyer for any consequential
or incidental damages of any nature whatsoever arising from nonconformity of goods,
defective goods, or delay in shipment or any other breach by seller.
Please feel free to email warning@compdotfitting.com with any questions or concerns.

• One touch connection reduces installation time and cost.

• Rugged ultraviolet and vibration resistant composite body.
• Various shapes and configurations to meet vehicle applications and make installations easier.
Specifications for FMVSS (D.O.T.) and SAE Compliant Fittings
Operating Fluid Air
Max. Operating Pressure 145psi (1.0MPa)
Size 5/32" 1/4" 3/8" 1/2" 5/8" 3/4"
At 75°F (24°C) 1200psi 1200psi 1400psi 950psi 900psi 800psi
Proof Pressure
At 200 °F (93°C) 450psi (3.1MPa)
Recommended Fluid and -40°F to 140°F (-40°C to 60°C)
Ambient Temperature*
Leak Rate at -40°F (-40°C) 7 Ncm3/min. or less
Thread ANSI/ASME B1.20.1, 1983 R1992
Thread Portion
Nut JIS B 0208 (Unified fine thread) ISO 263
Thread Sealant Fluorine/ Acrylic
Applicable Standards D.O.T. FMVSS 49 CFR 571.106, SAE J2494-3
Applicable Tubing Tubing conforming to both SAE J844 and D.O.T. FMVSS 49 CFR 571.106. Material:
Nylon12
Tube O.D. 5/32", 1/4", 3/8", 1/2", 5/8", 3/4"
www.P65Warnings.ca.gov

1. Chuck Stainless steel or Brass

2. Body Polybutylene Terephthalate (PBT), Brass
3/4. Tube seal, O-Ring Buna-N, Nitrile Rubber
5. Stud Brass
6. Sealant Flourine/ Acrylic
7. Guide Stainless Steel or Polyacetal (Acetal)
8. Stabilization Ring Stainless Steel
9. Release Button Polyacetal, POM (Acetal)
10. Tube support Stainless Steel/ Brass

126
 BRASS FITTINGS D.O.T. AIR BRAKE - NYLON TUBING

D.O.T. AIR BRAKE - NYLON TUBING

BRASS
WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
Tube
1/4 3/8 1/2 5/8 3/4
O. D
Th r e a d
7/16-24 17/32-24 11/16-20 13/16-18 1-18
Si z e - B
•Typical Application •Conformance
Air brake systems except where temperatures exceed Meets specifications and standards of SAE and DOT
+2000F or where battery acid can drip on tubing. FMVSS 571,106.

•Pressure •Assembly Instructions

Maximum operating pressure of 150 PSI. 1- Cut tubing to desired length.
2-Slide nut and then sleeve on tubing. Threaded end of
•Vibration nut “A” must face toward fitting body.
Fair resistance. 3-Insert tubing into the preassembled fitting. Be sure
tubing is bottomed in fitting.
•Temperature Range 4- Tighten nut to required torque as
-400F to +2000F (-400C to +930C). indicated on chart.

•Material Disassembling: Remove nut and pull tubing out of fit-

Brass ting body. Insert will remain in tubing.
Reassembly: Push tubing and insert into fitting body
•Used With until it bottoms. Thread nut onto fitting body and
NT Nylon Tubing - SAE J844 Type A and B. torque as in step 4.

• Tolerance
+/- .02 on all dimensions. Dimension data can change Tube Additional Number of Turns
without notice. Please call us when dimensions are critical S iz e from Hand-Tight
1 /4 3
•Advantages 3 /8 , 1 /2 4
www.P65Warnings.ca.gov

Easy to assemble (no tube preparation or flaring required.) 5 /8 , 3 /4 3 -1 /2

Built in tube support. Fittings utilize a ribbed sleeve for
compression and positive grip. May be used with copper
tubing by replacing nut, sleeve and insert with long nut
and spherical sleeve. Insert should be removed for copper
tubing use.

131
 D.O.T. AIR BRAKE - HOSE/ ENDS BRASS FITTINGS

D.O.T. AIR BRAKE REUSABLE HOSE/ FITTINGS

BRASS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
•Typical Application
Air Brake hose connections.
Meets SAE & DOT specifications • Tolerance
(FMVCS 10 GAL) +/- .02 on all dimensions. Dimension data can change
without notice. Please call us when dimensions are
•Pressure critical.
Determined by maximum working pressure for hose size.
•Assembly Instructions
Up to 125 psi
1- Slide nut and sleeve onto hose. Make sure bevel edge of
sleeve faces out toward fitting.
Temperature: -400F to + 1200 F ( -40°C to +48°C ) 2- Push hose into fitting until it bottoms.
3- Screw nut until contact is made with body hex.
•Advantages
Can be used for nearly any brake line. Easy to assemble NOTE: When reassembling fitting, body and
with a good selection of hose end configurations. Brass nut should be inspected. Only reuse if in proper condition.
material offers excellent resistance against corrosion. Sleeves should never be reused.

SLEEVE Part # Hose I.D. Approx.

FERRULE Size Wt. Lbs.
38-300 3/8” 0.02 ----
38-301 1/2” 0.02 ----

#60HC 3380-A 0903610 367 60RB

NUT

Part # Hose I.D. Approx.

Size Wt. Lbs.
38-306 3/8” 0.04 ----
38-307 1/2” 0.06 ----
www.P65Warnings.ca.gov

61RB #61HC 369 3380-B 0903624

NUT FOR USE WITH SPRING

Part # Hose I.D. Thread Approx.
Size Wt. Lbs.
38-312 3/8” 31/32-20 0.04 ----
38-313 1/2” 1-3/32-20 0.06 ----

#61HCS 0903613 3380-D 61RBSG

138
 SPECIALTY VALVES BRASS FITTINGS

SPECIALTY VALVES AND COCKS

BRASS

BRASS
WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
DRAIN COCKS AIR VALVES
PAGE 147-148

3, 4 AND 6 WAY NEEDLE

PAGE 153-154 PAGE 150-151

MARINE & ANTI-SIPHON PANEL MOUNT BALL VALVES

PAGE 154 PAGE 155

TRUCK MINI BALL

PAGE 152 PAGE 155

SOLID BOTTOM SHUT-OFF CHECK

PAGE 152 PAGE 156
www.P65Warnings.ca.gov

SPRING BOTTOM SHUT-OFF

PAGE 149 MORE VALVES ON OUR WEBSITE
See our valve section for much, much more!

146
 LEAD FREE BRASS FITTINGS LEAD FREE

LEAD FREE

LEAD FREE
What is the new lead-free requirement?
In 2011, the Reduction of Lead in Drinking Water Act was signed into law. The Act has reduced the lead content
allowed in drinking water system and plumbing materials by changing the definition of "lead-free" in Section
1417of the Safe Drinking Water Act.

The term "lead-free" has been updated from notmore that 8% lead content to mean "not more than a weighted
average of 0.25% lead when used with respect to the wetted surfaces of pipes, pipe fittings, plumbing
fittings and fixtures."

How do I know which products must meet the

new lead-free requirement?
The prohibitions on use and introduction into commerce ap-
ply to all pipe, pipe fittings, plumbing fittings, and fixtures
(henceforth reffered to as "products"), including stocked in-
ventories that have not been installed. This includes coated
or uncoated brass or bronze materials. By using the flow-
chart below as a guide, you can determine if a product must
meet the new lead-free requirement:

Lead-Free Requirement Exemptions

(A) The new requirement does not apply to pipes, pipe fit-
tings, plumbing fittings, or fixtures, including backflow pre-
venters, that are used exclusively for nonpotable service
such as manufacturing, industrial processing, irrigation,
outdoor watering or any other uses where the water is not
anticipated to be used for human consumption.

(B) The new requirement does not apply to toilets, bidets, urinals,
fill valves, flushometer valves, tub fillers, shower valves, service
saddles or water distribution main gate valves 2 inches in diam-
eter or larger.

157
 VALVES VALVES

VALVES
VALVES

VALVES........................................................ 168-213 Y Strainer............................................................ 194

Check Valves............................................. 195-197
LEAD FREE BALL VALVES.................... 169-171
LEAD FREE VALVES......................................... 172 STAINLESS STEEL VALVES
BRASS VALVES......................................... 173-197
Full Port Ball....................................................... 173
Locking Handle................................................ 174 2000# Full Port.................................................. 198
Butterfly Handle............................................... 175 Standard Port.................................................... 199
N/P Ball Valve.................................................... 176 1,000 PSI Full Port............................................ 200
N/P Ball w/SS Trim........................................... 177 SS Mini Ball Valve.................................... 201-202
Italian Ball Valve............................................... 178 Check Valves............................................. 203-207
M X F Ball Valve........................................ 179-180 Y-strainer, Globe,Gate.................................... 207
Tee Handle M X F Ball..................................... 181
M X F Ball Locking handle............................ 182 Carbon Steel valves............................... 208-211
Spring Handle Ball Valve............................... 183
Right Angle Ball valve.................................... 183 2,000# Standard Port..................................... 208
Wye, 3-Way Ball Valve..................................... 184 2,000 # FP 2-Piece............................................ 209
Safety Exhaust Ball Valve.............................. 184 Hi Pressure 2-Way Valves.............................. 210
Gas Valves........................................................... 185 Hi Pressure 3-Way Balves.............................. 210
Mini Ball Valves........................................ 186-189 Check valves-5,000#....................................... 211
3-Way Valves...................................................... 190
Strainer Ball Valve............................................ 191 PVC Valves................................................. 212-213
Vacuum Breaker/Hose Bibb......................... 191
Bent Nose Garden Valve................................ 191
Gate Valves......................................................... 192
Quick Opening Gate....................................... 193

168
 NIPPLES FITTINGS

NIPPLES & FITTINGS

NIPPLES & FITTINGS

BRASS & BRONZE.................................... 215-234 STAINLESS STEEL.............................................. 235

Brass Nipples - Sch 40........................... 215-221 Stainless Nipples..................................... 235-240

EH Sch 80.................................................................... Sch 80 SS Nipples....................................................
C/P Brass Nipples............................................. 222 150# Cast SS Fittings............................. 241-248
Bronze Fittings......................................... 223-231 1,000# Barstock SS fittings NEW........................
EH Bronze Fittings................................................... 3000# SS Fittings.....................................................
Lead Free Bronze Fittings.................... 223-230
C/P Fittings........................................................ 231 BLACK & GALVANIZED.......................... 249-286
Bronze Cleanout Plugs.................................. 232
Bronze Drop Ear Elbows................................ 232 Sch. 40 Welded Steel Nipples............. 250-257
Bronze Barbs for PL. Pipe.............................. 233 Sch. 80 Seamless Steel nipple............ 258-263
Steel Barbs for PL. Pipe.................................. 233 Sch. XXS Seamless Steel Nipple................. 264
Lead Free Bronze Barbs for PL. Pipe.......... 234 Groove Nipples........................................ 265-266
Stainless Steel Barbs for PL. Pipe................ 234 Merchant Couplings....................................... 267
Stainless Steel Well Couplings.................... 234 API Line Couplings.......................................... 268
Stainless Steel Merchant Couplings......... 234 Malleable Fittings................................... 269-278
Steel Fittings............................................. 279-280
300# Malleable........................................ 281-282
Forged Steel Fittings..............................................
Bull Plugs and Swages.......................... 283-284
Forged Steel Fanges.............................. 285-286

Copper Fittings........................................ 287-293

214
 BRASS NIPPLES BRASS NIPPLES

NIPPLES & FITTINGS

We hereby certify that to the best of our knowledge and belief the CDA 230 alloy seamless Red Brass Pipe from which our nipples are
produced meet the requirements of ASTM Specifications B43 and is free of mercury contamination. The chemical analysis is 85% copper,
15% Zinc and conforms to federal Specifications WWN-351. Our brass nipples meet ANSI/ASTM B687-96 and MS51846 for standard
brass nipples, and MS51872 for extra heavy brass nipples.

Threads: Nipples are threaded with American Standard taper pipe threads (NPT) in accordance with screw-thread standard for Federal
Services Handbook H-58. ANSI B1.20.1

This product is certified by NSF to NSF/ANSI 61 for use in drinking water supplies of pH 6.5 and above.

• ASTM B43
• ANSI B1.20.1, WW-N-351
• ANSI/ ASTM B687-96
• NSF-61 Approved
• MS51846 STD Brass Nipples
• RoHS compliant

STANDARD RED BRASS 85% No-Lead 125LB seamless Threaded

PIPE WITH THREADED ENDS SPECIFICATIONS: Red Brass Nipples - 2200

LEAD
Pipe Size Dimension in Inches Allowable Pressure
in Wall POUNDS PER SQUARE INCH
O.D. I.D.
Inches Thickness Standard @ @ @ @
1/8" .405 .281 .062 Size (Inches) 100° F 200° F 300° F 400° F
.540 .376 .082 1/8" 370 370 320 140

FREE
1/4"
3/8" .675 .495 .090 1/4" 870 870 760 330
1/2" .840 .626 .107 3/8" 890 890 780 340
3/4" 1.050 .822 .114 1/2" 900 900 790 340
1" 1.315 1.063 .126 3/4" 810 810 710 310
1-1/4" 1.660 1.368 .146 1" 630 630 560 240
1-1/2" 1.900 1.600 .150 1-1/4" 690 690 610 260
2" 2.375 2.063 .156 1-1/2" 630 630 560 240
2-1/2" 2.875 2.501 .187 2" 540 540 480 210
3" 3.500 3.062 .219 2-1/2" 450 450 390 170
3-1/2" 4.000 3.500 .250 3" 510 510 450 190
4" 4.500 4.000 .250 3-1/2" 570 570 500 220
4-1/2" 5.000 4.500 .250 4" 510 510 440 190
5" 5.563 5.063 .250 5" 410 410 360 160
6" 6.625 6.125 .250 6" 340 340 300 130

215
 BRONZE FITTINGS BRONZE FITTINGS

BRONZE FITTINGS

NIPPLES & FITTINGS

U
Class 125 (150) For steam, water, gas, oil and air service
L FM
Standard specifications • UL/ FM Approved

WARNING: This product can expose you to chemicals, including Nickel, which are known to the State of California to cause cancer.
UL842, UL258, UL125,FM
• 1S0 9001:2000
Materials - ASTM B62-93 (85,5,5,5) C83600 • Not Lead Free
Dimensions - ANSI B 16.15
• RoHS Compliant
Threads - ANSI B2.1 or BA 21 and Fed. WW-P-460C, MSS-SP-106, ANSI/ASME B1.20.1

Bronze threaded fittings are manufactured from smooth-cored castings, designed to provide full flow with minimum restriction. All
threads are accurately machined and gauged to ensure a perfect fit with the pipe. All fittings are individually tested under water to
ensure quality. Bronze provides a tighter seal and is easier to install than other metals. Can be used for water, plumbing, heating, pneu-
matic and marine applications, able to resist the harmful effects of corrosion when coming into contact with salt water or fresh water
polluted with mineral acids or peaty soils.

LEAD FREE BRASS FITTINGS

For more information, visit www.P65Warnings.ca.gov

• Approved to ANSI/NSF 61-4 California AB 1953 • Brass fittings dimensions conform to ASME B16.15
• Meets Federal State Drinking Water Act, Lead Free Requirement •NPT threads on all fittings conform to ASME B1.20.1
• Brass fittings conform to AWWA C800 • Brass unions conform to specification A-A-59617
• Brass castings conform to ASTM B584, UNS Alloy C8933 • Manufacturing facilities are ISO 9001:2008

223
 STAINLESS STEEL SCH 40 STAINLESS STEEL NIPPLES
STAINLESS STEEL NIPPLES

NIPPLES & FITTINGS

SCHEDULE 40 WELDED SCHEDULE 80 SEAMLESS
Stainless steel pipe nipples are manufactured from stain- • SEAMLESS FOR UNRESTRICTED FLOW
less steel pipe that conforms to specification ASTM A312/ • USE WITH AIR, WATER, OIL, NATURAL GAS, STEAM
SA312. • FITTINGS: USE THREADED CLASS 3000 HIGH-PRESSURE
STAINLESS STEEL.
All stainless steel nipples conform to specification ASTM
A733. Threads conform to the requirements of ANSI • ASTM A733 • ASTM A312 • ANSI/ ASME B1.20.1
B1.20.1. • PSI 3000

304 316
The basic alloy. Type 304 (18-8) is an austenitic steel possess- For severe environments. Of course, there are many industrial
ing a minimum of 18% chromium and 8% nickel, combined processes that require a higher level of resistance to corro-
with a maximum of 0.08% carbon. It is a nonmagnetic steel sion than Type 304 can offer. For these applications, Type
which cannot be hardened by heat treatment, but instead. 316 is the answer.
must be cold worked to obtain higher tensile strengths.
In type 316, the nickel content is increased slightly. What
Because of its ability to withstand the corrosive action of distinguishes Type 316 from Type 304 is the addition of mo-
various acids found in fruits, meats, milk, and vegetables, lybdenum up to a maximum of 3%.
Type 304 is especially suited for all types of dairy equipment
piping and valves, the brewing industry, the citrus and fruit Molybdenum increases the corrosion resistance of this
juice industry, and in food processing applications. Also used chromium-nickel alloy to withstand attack by many industrial
for the dye tanks, pipelines buckets, dippers, etc. that come chemicals and solvents, and, in particular, inhibits pitting
in contact with the lormic, acetic, and other organic acids caused by chlorides. As such, molybdenum is one of the single
used in the dyeing industry. most useful alloying additives in the fight against corrosion.

In the marine environment, because of it slightly higher Type 316 can withstand corrosive attack by sodium and
strength and wear resistance than type 316 it is also used calcium brines, hypochlorite solutions, phosphoric acid; and
for nuts, bolts, screws, and other fasteners. It is also used the sulfite liquors and sulfurous acids used in the paper pulp
for springs, cogs, and other components where both wear industry. This alloy, therefore, is specified for industrial equip-
and corrosion resistance is needed. ment that handles the corrosive process chemicals used to
produce inks, rayons, photographic chemicals, paper, textiles,
bleaches, and rubber. Type 316 is also used extensively for
surgical implants within the hostile environment of the body.

Type 316 is the main stainless used in the marine environ-

ment, with the exception of fasteners and other items where
Both #304 and #316 nipples are NSF/ANSI 372 and
strength and wear resistance are needed, then Type 304 (18-8)
NSF/ANSI 61 compliant.
is typically used.

235
 STAINLESS STEEL 304 & 316 150# SS FITTINGS

NIPPLES & FITTINGS

WARNING: This product can expose you to chemicals, including Chromium, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
150# 304 & 316 Stainless Steel Fittings

Our high quality standard pattern 150lb rated stainless steel threaded fittings are manufactured to the highest standards.
All stainless steel fittings are monitored by our quality control personnel for strict compliance with applicable standards
and specifications.

These stainless steel pipe fittings are excellent for uses that involve chemicals or liquids that may be corrosive. Along
with fighting corrosion, a stainless steel pipe fitting will prevent contamination making it useful to many professionals.

• Use with air, water, oil, natural gas, steam

• NPT and FNPT threads conform to ASME B1.20.1
• Maximum Pressure: 300 psi @ 72 F;150 psi @ 366 F for steam
• Maximum Steam Pressure: 150 psi
• Material Conforms to ASTM A-351. Class 150 Pressure Ratings
• Manufacturing facility is ISO 9001:2008
• 304 Stainless Steel is economically priced, chromium-nickel material that offers very good corrosion resistance. 316
Stainless Steel has higher nickel content and contains molybdenum for even better corrosion resistance.

HIGH PRESSURE 1000# BARSTOCK HIGH PRESSURE 3000# FORGED

A182 and ANSI/ASME B16.11.

For more information, visit www.P65Warnings.ca.gov

1000# 3000#
• Stainless bar stock dimensions conform to MSS SP-114 • Use with air, water, oil, natural gas, steam
• NPT threads conform to ASME B1.20.1 • Maximum Pressure:
• Manufacturing facility is ISO 9001:2008 Type 304 SS: 2,570 psi @ 72°F;
• Fittings meet applicable chemical & physical properties 1,965 psi @ 350°F for steam
Type 316 SS: 3,000 psi @ 72°F
2810 psi @ 350°F for steam
• Pipe Nipples and Pipe: Use threaded Schedule 80
thickwall stainless steel

241
 STEEL NIPPLES BLACK & GALVANIZED SCH 40

NIPPLES & FITTINGS

BLACK AND GALVANIZED STEEL NIPPLES
Product Specifications

WARNING: This product can expose you to chemicals, including Cobalt, which are known to the State of California to cause cancer.
Welded steel pipe nipples both galvanized and black in diameters ranging from 1/8” up to 4” in lengths from close to 12”
and cut-pipe up to 120”. -200°-150° Temp Rating.
Technical Specifications
Standards: Product complies with ASTM A-53, A-733 and ANSI B1.20.1 for threading, dimensions and pipe specifications.
Pipe: Complies with ASTM A-53 mill tested schedule 40 and 80 for both Welded & Seamless Meets ANSI B36.1. All pipe
is hydrostatic tested.
Galvanized: Zinc coating applied by hot dipped. Galvanized complying with ASTM A-123, NSF approved, RoHS compli-
ant.
Black: Protected against oxidation with varnish coating.
Cutting Procedure: All pipe is roller cut. A visual inspection of seams, excessive galvanizing, mid-welds, poor galvanizing,
bends, roundness, under and over weight of the pipe is made at the time it is cut. This is done for every length of pipe. Pipe
lengths are cut to a tolerance of + or - 1/16” of the actual length.
Threading Procedure:
All pipe is chaser thread cut to American Standard Tapered Pipe Thread standards. This is 3/4” taper per foot. Pipe is visually
inspected for roundness of threads and other visual faults as it is removed from the threading machine.

SCHEDULE 80 XXS SEAMLESS XXS SEAMLESS

For more information, visit www.P65Warnings.ca.gov

• ASTM A106 Grade B Seamless Pipe

• ASTM A 53
• WWN 351
• Standard NPT Tapered Pipe Threads as per ANSI B 1.20.1 Specification

249
 MALLEABLE FITTINGS MALLEABLE FITTINGS

MALLEABLE FITTINGS

NIPPLES & FITTINGS

• Saturated steam pressure 150 PSI @
350°F
• Max pressure 300 PSI @ 150°F
• Temp range -20°F to 350°F

WARNING: This product can expose you to chemicals, including Chromium, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
ISO 9002 - CERTIFICATE OF QUALITY - UL/FM LISTED MALLEABLE IRON - ANSI B 16.3
Our quality fittings are made with care and attention to detail. With better molds we F° Class Sizes Sizes Sizes
can reduce parting lines and rough edges resulting in better fluid flow. By using a low 150 1/4-1 1 1/4-2 2 1/4-3
PSIG 300# 300# 300#
temperature galvanizing process the coating is more durable which means a longer
-200-150 300 2000 1500 1000
lasting fitting. All Fittings are 100% Pressure Tested to 300# Class. 200 265 1785 1350 910
(Every fitting is subjected to an underwater fitness test to ensure the highest quality) 250 225 1575 1200 825
SPECIFICATIONS 300 185 1360 1050 735
• MATERIAL: ASTM A 197 - Cuppla Malleable Iron, ASTM A 153 - Hot dipped 366* 150 1150 900 650
galvanizing • Coating ASTM A164 LS *Permissible for service temperature up to
• DIMENSIONS: ANSI B 16.3 - Malleable Iron threaded fittings, ANSI B 16.14 - 366°F, reflecting the temperature of saturated
Ferrous Pipe Plugs, Bushings etc..., ANSI B 16.39 - Malleable Iron threaded pipe unions. steam at 150 psig.
• THREADS: ANSI B 2.1 or BS 21 ASME B1.20.1 • RoHS Compliant • Tapered Threads
• Pressure - Saturated steam 150 PSI @350°F: Max pressure 300 PSI - 150°F
• Temperature range -20 - 350°F

STEEL FITTINGS 300lb MALLEABLE FITTINGS

For more information, visit www.P65Warnings.ca.gov

• 1010 Carbon Steel, 3/4 taper threads ( see hy- Max. pressure: 300 psi WOG @ 72°F; 150 psi
draulic section for 7/8 taper threads.) WOG saturated steam
• Finish or coating • Black Dipped in rust resistant • Meet ANSI/ ASME B1.20.1 standards
• Galvanized, Zinc Plated (Inside and Out) • Black meet ASTM 197 standards

BULL PLUGS AND SWAGES FLANGES

269
 COPPER FITTINGS WROT SOLDER JOINT

COPPER FITTINGS

NIPPLES & FITTINGS

SYMBOL OF JOINT ENDS • Temp range 32° to 200°F
• Pressure @100° - 1/8-1 : 500 PSI
C Solder joint fitting end made to receive copper tube diameter - 1-1/4-2 : 400 PSI
Ftg. Solder joint fitting end made to copper tube diameter - 2-1/2 - 3: 300 PSI
F Internal ANSI Standard Taper Pipe Thread-Female NSF - 61 CERTIFIED
M External ANSI Standard Taper Pipe Thread-Male ALLOY C12200
Threaded ends ANSI/ ASME B1. Solder ends ASTM B88

THE ABOVE CONFORMS TO ASTM B 88 & ASTM B 306, A 306

A A
T T
T T
O O O O
K

G G

F TT
F
MALE (FITTING) FEMALE (COPPER)
Joint Ends
Male End Female End Inside
Nominal Metal Thick-
Outside Average Length Inside Average Length Diameter
Size Actual O.D. Actual O.D. ness T (in)
Diameter Tolerance (Min) H Diameter Tolerance (Min) G O (in)
MIN in MAX in MIN in MAX in
(A) in (mm) (in) F (in) (mm) (in)
1/8 2/8 2/8 2/8 3/8 2/8 2/8 2/8 3/8 0 2/8
1/4 3/8 3/8 3/8 3/8 3/8 3/8 3/8 3/8 0 2/8
3/8 4/8 4/8 4/8 3/8 4/8 4/8 4/8 3/8 0 3/8
0.03 0.03
1/2 5/8 5/8 5/8 4/8 5/8 5/8 5/8 3/8 0 4/8
5/8 6/8 6/8 6/8 5/8 6/8 6/8 6/8 5/8 0 4/8
3/4 7/8 7/8 7/8 6/8 7/8 7/8 7/8 5/8 0 5/8
1 1-1/8 1-1/8 1-1/8 7/8 1-1/8 1-1/8 1-1/8 7/8 0 7/8
0.04 0.04
1-1/4 1-3/8 1-3/8 1-3/8 1 1-3/8 1-3/8 1-3/8 1 0 1-1/8
1-1/2 1-5/8 1-5/8 1-5/8 1-1/8 1-5/8 1-5/8 1-5/8 1-1/8 0 1-3/8
2 2-1/8 2-1/8 2-1/8 1-3/8 2-1/8 2-1/8 2-1/8 1-2/8 0 1-6/8
2-1/2 2-5/8 0.05 2-5/8 2-5/8 1-4/8 2-5/8 0.05 2-5/8 2-5/8 1-4/8 1/8 2-1/8
3 3-1/8 3-1/8 2-1/8 1-6/8 3-1/8 3-1/8 3-1/8 1-5/8 1/8 2-5/8
4 4-1/8 4-1/8 4-1/8 2-1/8 4-1/8 4-1/8 4-1/8 2-1/8 1/8 3-4/8

1/8" 1/4" 3/8" 1/2" 5/8" 3/4" 1"

1-1/4" 1-1/2" 2"

287
 PVC SCHEDULE 80 FITTINGS PLASTIC FITTINGS

PLASTIC FITTINGS
PLASTIC

PIPE FITTINGS HOSE BARB FITTINGS GARDEN HOSE FITTINGS

• Nylon • Nylon • Nylon

• Polyethylene • Polyethylene
• Polypropylene • Polypropylene

NYLON & POLYPROPYLENE POLYPROPYLENE PUSH-IN

COMPRESSION FITTINGS TUBE FITTINGS AND VALVES

Machined Schedule 80 PVC nipples • NSF 61 certified for use with

comply fully with ASTM D2464, drinking (potable) water
• Max Temperature: 140°F
• Max Pressure: Not Rated

SCH 80 PVC NIPPLES SCH 40 PVC FITTINGS SCH 80 PVC FITTINGS

Machined Schedule 80 PVC nipples • NSF 61 certified for use with PVC Material is Type 1 according
comply fully with ASTM D2464, drinking (potable) water to the American Society for Testing
threads conform to ASTM F1498, • Max Temperature: 140°F Materials (ASTM) D-1784. Fittings
and the pipe is extruded from PVC • Max Pressure: Not Rated conform to ASTM D-2464 & ASTM
D-2467. Temperature rating is 140°F.
1120-1220 meeting ASTM D1784 Resistant to corrosion, strong and
PSI is based on water at 73°F. Derate
and meets ASTM D1785, products rigid - commonly used in low pres- 50% at 110°F and 78% at 140°F. Not
standard 21-70 sure plumbing applications. ASTM recommended for use in compressed
D1784 and D2466. air or gas systems.

294
 COMBINATION HOSE NIPPLES
ALUMINIUM
HOSE ACCESSORIES

STAINLESS STEEL
CAM AND GROOVE

FIRE HOSE FITTINGS

HOSE ACCESSORIES

BRASS
POLYPROPLYENE

COUPLINGS
HOSE ACCESSORIES

UNIVERSAL/ GROUND JOINT

WARNING: This product can expose you to chemicals, including Chromium, which are known to the State of California to cause cancer and birth defects or other reproductive harm.

305
For more information, visit www.P65Warnings.ca.gov

HOSE ACCESSORIES
 HOSE CLAMPS HOSE CLAMPS

HOSE CLAMPS
CLAMPS

WARNING: This product can expose you to chemicals, including Chromium, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
WORM GEAR QUICK RELEASE
PAGE 317-320 PAGE 321

T-BOLT SPRING LOADED T-BOLT

PAGE 322 PAGE 323

CONSTANT TORQUE V-BAND

PAGE 324 PAGE 324

MUFFLER EXHAUST
PAGE 325 PAGE 326

For more information, visit www.P65Warnings.ca.gov

1 EAR, 2 EAR, GAPLESS PRE-FORMED
PAGE 327-328 PAGE 329-330

TOOLS NON-PERFORATED OR
PAGE 331 LINED BAND
PAGE 332

RUBBER LINED HOSE FERRULES

PAGE 333 PAGE 334

316
 TUBING TUBING TUBING
TUBING

TUBING
POLYURETHANE POLYETHYLENE NYLON
Sold individually boxed Sold individually boxed

Natural, Black, Blue, Green, Red, Yellow, Orange

PVC COPPER AND ALUMINUM

• Clear Sold individually boxed

TYPE L AND ALUMINUM

REFRIGERATION

1 /1 6 1 /8 3 /1 6 1 /4 5 /1 6 3 /8 1 /2 5 /8 3 /4

335
 HIGH PRESSURE SPRAYER

342
NOZZLES
HIGH PRESSURE SPRAYERS

STRAIGHT THROUGH QDS

HIGH PRESSURE SPRAYERS

FITTINGS AND SWIVELS

SPRAY GUNS AND WANDS

HIGH PRESSURE SPRAYER

WARNING: This product can expose you to chemicals, including Chromium, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information, visit www.P65Warnings.ca.gov
 PNEUMATICS PNEUMATICS

PNEUMATICS
PNEUMATICS

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm.
1/4" 3/8" 1/2" 1/4" 1/4" 3/8" 1/4" 1/4" 3/8"
INDUSTRIAL INTERCHANGE ARO AUTO AUTO LINCOLN STRAIGHT STRAIGHT
THRU THRU

QUICK DISCONNECTS BREATHER VENTS, MUFFLERS

• Universal • Mufflers
• ARO 210 • Snubbers
• Lincoln • In-line filters
• Industrial • Breather vents
• Automotive • Control valves
• ST Series - High Flow • Manifolds

For more information, visit www.P65Warnings.ca.gov

PNEUMATIC ACCESSORIES GAUGES

• Kits NEW • Liquid filled & Dry

• Tire gauge • Lower mount & center mount
• Tank and vent valves • Water test
• Blow guns • Syphons
• Air chucks
• Inflators

348
TRUCK AND TRAILER AIR COILS

TRUCK AND TRAILER

TRUCK & TRAILER

WARNING: This product can expose you to chemicals, including lead, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information, visit
INDUSTRY GRADE NYLON AIR COIL ASSEMBLY - SET
• Each kit contains one Emergency (Red) and one service (Blue) 1/2" O.D.
nylon tubing assembly.
• 1/2" -14 NPTF end fitting with heavy gauge spring.
• Assemblies meet SAE J844 and DOT FMVSS 106 requirements.
• Temp rating -40° - +208°
Part # Length Pigtail Length Pigtail Length
Tractor end Trailer end
39404 12' 6" 6" ----
39400 15' 12" 12" ----
39402 15' 40" 12" ----
39406 20' 12" 12" ----

FIFTH WHEEL SLIDER COIL

• Temperatures range -40 to 208°F
• 150 psi max pressure rating
• Meets SAE J844 and DOT FMVSS 106 requirements.
• (2) ¼” OD fittings assembled

Part # Description Length Fittings

39839 5th Wheel slider coil up to 54" (2) 1/4" MPT ----
39838 5th Wheel slider coil up to 72" (2) 1/4" MPT ----

3-IN-1 AND 4-IN-1 COMBINATION AIRLINE CABLE

• (2) 3/8” ID SAE J1402 rubber service and emergency with blue (service)
and
red (emergency) gladhand grip handle
• Color-coded grip helps to minimize incorrect tractor/trailer connections
have glad handle with Vibraseal
• ABS power line (green) – meets SAE J2222 requirements
• Auxiliary power line (yellow) – fitted with SAESS60 plugs that have an
inverted (male) ground pin 4-in-1 only
www.P65Warnings.ca.gov

• SAE J560 Plugs with sleeves for superior corrosion protection

and strain relief
• Corrosion resistant all brass fittings 1/2" male NPT w/ Vibraseal
• Tapered grip flexes with airline during tight turns for kink protection
• Temp rating -40 - 208°F
Part # Description
39825 Combo 3 in 1 assembly 15 ft. ----
39962 Combo 4 in 1 assembly 15 ft. ----

371
 HYDRAULIC ADAPTERS & ACCESSORIES
HYDRAULIC ADAPTERS

HYDRAULICS
STEEL ADAPTERS HYDRAULIC QUICK HYDRAULIC VALVES &
DISCONNECTS ACCESSORIES

Technical information.... 394 Thread to Connect - Wing. 427 Flow Control Valve............... 430
Profile size chart............. 400 ISO A Interchange................ 427 Variable Flow Control.......... 431
Steel Pipe Swivels................. 402 ISO B Interchange................. 427 Air Breathers........................... 431
37° JIC Flare Straights.......... 404 Flush Face ISO........................ 428
37° JIC Flare Shapes............. 406 VEP Series................................ 428
Bulkhead Adapters.............. 407 AG Interchange..................... 429
Steel Pipe Fittings................. 409 Hydraulic Jack Q/D............... 429
O-Ring Adapters Straight.. 413
JIC Swivels............................... 415
O-Ring Adapters................... 417
O-Ring Face Seal................... 420
BSPT/ BSPP Adapters.......... 423
Metric Adapters.................... 425

PLATING SPECIFICATION
Our standard Trivalent, Cr+3 plating performs at nearly double the S.A.E. corrosion resistance requirement. The
plating meets ASTM B633, Fe/Zn 5. The thickness is 5um-13um. This plating is silver in appearance and has
been testing at 96 hours to white rust and 120 hours to red rust.

393