Applied Thermodynamics C211 PDF

1. What do you understand by the Air standard efficiency?
The cycles encountered in actual devices are difficult to analyse because of the presence
of friction, and the absence of sufficient time for establishment of equilibrium conditions
during the cycle. In order to make an analytical study of a cycle feasible, we have to
make some idealizations by neglecting internal Irreversibility’s and complexities. Such
cycles resemble the actual cycles closely but are made up of internal reversible
processes.These cycles are called ideal cycles.
State the assumptions made in analysis of air standard cycles.Air standard cycles are
thermodynamic cycles with air assumed as the working substance.In these cycles the
combustion process is replaced by heat addition and exhaust process by heat rejection
process. The efficiency of such cycles are called as air standard efficiency given by
Actual efficiency is always less than air standard efficiency given by term relative efficiency
2. State the assumptions made in air standard cycle analysis

 The gas in the cycle is perfect gas and obeys gas laws, has constant specific heats.
 The physical constants of gas are same as that of air.
 The expansion and compression are adiabatic process.
 No chemical reaction takes place in cylinder. Heat is supplied or rejected by source or
sink.
 The cycle is considered as closed.
3. Derive an expression for the air standard efficiency of carnot cycle. Show the cycle on
PV and T-S diagrams.
T 2 3
2
3
P
4
1 1
4
S
V
The Carnot cycle consists of an alternate series of two reversible isothermal and two reversible
adiabatic processes. Since the processes in the cycle are all reversible the Carnot cycle as a
whole is reversible
Process 2–3: Gas expands isothermally absorbing heat Qs from the source at Temperature TH.
Work done during this process is given by the area under 2 – 3 (W2-3)
Process 3–4: During this process cylinder is thermally isolated from the heat reservoir and the
head is insulated by the piece of perfect insulator. Gas expands reversibly and adiabatically to
temperature TL (point 4). Work done is W34.
Process 4–1: Cylinder is in contact with the heat reservoir at TL. Gas is isothermally and
reversibly compressed to point 1 rejecting an amount of heat QR to the sink. The work done on
the W41.
Process 1-2: Cylinder is again isolated thermally from the thermal reservoir; gas is recompressed
adiabatically and reversibly to point 2. The cycle is now complete. Work done is W12
The efficiency of the Carnot engine is given by,
1-2 Process Adiabatic
2-3 Process: Isothermal Heat addition

3-4 Process Adiabatic
4-1 Process: Isothermal Heat Rejection
Substituting in efficiency formula
--------------A
1-2 process adiabatic
( )
( ) ------i)
( )
( ) ----------ii)
Comparing i) and ii)
( ) ( ) ; ;
Substituting in Equation A
4. Define work ratio and Mean effective pressure
Work ratio is define as ratio of net work done to positive work
Mean effective pressure may be defined as the theoretical pressure which, if it is maintained
constant throughout the volumechange of the cycle, would give the same work output as that
obtained from the cycle.
5. Derive an expression for the air standard efficiency of Otto combustion cycle in terms of
compression ratio. Show the cycle on PV and T-S diagrams.
The cycle consists of two adiabatic processes and two constant volume processes as shown in P-
V and T-S diagrams.
Process 1–2: Gas is compressed isentropically. Q=0
Process 2–3: During this process heat is supplied from the heat reservoir at constant
volume.
Process 3–4: Gas expands isentropically to point 4. Q=0
Process 4–1: Heat is rejected to sink at constant volume.
----------------A
1-2 Process is adiabatic
( )
Also,
3-4 adiabatic process
( ) ( )
or
Substituting in equation A
6. Derive an expression for the air standard efficiency of Diesel combustion cycle in terms
of compression ratio and cut off ratio. Show the cycle on PV and T-S diagrams
This cycle is also known as constant pressure cycle because heat is added at constant pressure.

Process 2–3: During this process heat is supplied from the heat reservoir at constant
pressure.
--------------A
Let Compression ratio , Cut off ratio , Expansion Ratio
( ) or ------------i)
2-3 Process is constant Pressure process =
ie ie
; --------------ii)
3-4 Adiabatic process
( ) or or
--------------iii)
Substituting i) ii) and iii) in A

* +
7. Derive an expression for the air standard efficiency of dual combustion cycle in terms of
compression ratio , cut-off ratio and explosion ratio. Show the cycle on PV and T-S
diagrams ( March2001)
3 4
P 4
T P=C
3
V=C
2
5
2 5
1
1
V S
Process 2–3: During this process heat is supplied from the heat reservoir at constant volume.
Process 3–4: During this process heat is supplied from the heat reservoir at constant pressure.

=
[ ]
Let Compression ratio , Cut off ratio , Expansion Ratio
Explosion ratio
as V2=V3 , V5=V4
( ) or
2-3 process constant volume
ie =
3-4 constant pressure process
ie
( ) or or
( ) ( )
[ ]
8. Derive an expression for mean effective pressure for otto cycle in terms of compression
ratio and explosion ratio.
R= gas constant, r=compression ratio
( ) ( )
( )
( )
---------------------1
( ) or
ie =
( ) ( ) as
[ ]
[ ]
9. Derive an expression for mean effective pressure for Diesel cycle in terms of
compression ratio and cut-off ratio
( ) ( )
( )
( )
( ) or
2-3 process (constant volume process. )
ie
T3=
3-4 process (adiabatic process)
( ) or
, -
, -
[
Expression for cut-off ratio in terms of k:Let ‘k’ be the cut-off in percentage of stroke (from V1
to V2)
10. Derive an expression for mean effective pressure for Duel cycle in terms of compression
ratio, cut-off ratio and explosion ratio
( ) ( )
( )
( )
;
( )
( )
( ) or
ie =
3-4 process constant pressure process
ie
( )
( )
( )
(( ) ( ) )
(( ) ( ) )
[ ]
[ ( )]
11. Prove that for same compression ratio and heat input, Otto cycle efficiency is more than
Diesel cycle
3' 4'
3 4'
P 3"
2" T
3"
2 2" 3'
2' 4"
2 5'
4"
4
5
4
1
A B C D
V
S
The comparison of these cycles for the same compression ratio and same heat supply are
shown in on both p – V and T – S diagrams. In these diagrams, cycle 1-2-3-4-1 represents Otto
Cycle, cycle 1-2’-3’-4’-5’-1 represents Dual cycle and cycle 1-2”-3”-4”- 1 represents the diesel
combustion cycle for the same compression ratio and heat supply.
From the data heat supplied for all the cycle is same
Hence area under heat supply curve in T-S diagram for all the cycle is same
Hence area A23B = area A2’3’4’C = area A2”3”D as All the cycles start from the same initial
point 1 and the air is compressed from state 1 to state 2 as the compression ratio is same.
From the above equation it can be seen that since is same for all the three cycles efficiency of
the cycle depends on and efficiency is inversely proportional to heat of rejection
It is seen from the T-s diagram, area A14B ( Area A1”5”C

( Area A1’4’D (
Consequently Otto cycle has the highest work output and efficiency. Diesel cycle has the least
efficiency and dual cycle has the efficiency between the two.Therefore for the same compression
ratio and same heat rejection, Otto cycle is the most efficient while the Diesel cycle is the least
efficient.
12. Prove that for same Maximum pressure and maximum temperature Diesel cycle
efficiency is more than Otto cycle or Prove that for same Maximum pressure and same
output Diesel cycle efficiency is more than Otto cycle
12341 represents otto and 12’3’4’1 diesel cycle respectively in T-S diagram and P-V diagram
Since Maximum pressure and maximum temperature is same for both cycles 3 is the common
point for both cycles in PV and TS diagram
From the above equation it can be seen that since is same for diesel and otto cycles efficiency
of the cycle depends on and efficiency is proportional to heat of supply
It is seen from the T-s diagram, area A23B ( Area

A2’3’B(
Hence,
13. Prove that for same Maximum pressure and same heat input Diesel cycle efficiency is
more than Otto cycle
12341 represents otto and 12’3’4’1 diesel cycle respectively in T-S diagram and P-V diagram
From the data heat supplied for all the cycle is same
Hence area under heat supply curve in T-S diagram for both the cycle is same
Hence area A23B = area A2’3’C as All the cycles start from the same initial point 1
From the above equation it can be seen that since is same for both the cycles efficiency of the
cycle depends on and efficiency is inversely proportional to heat of rejection
It is seen from the T-s diagram, area A14B ( Area

A14’C(
From figure heat rejection in diesel cycle is less than Otto cycle
14. In an otto cycle the upper and lower limits for the absolute temperature respectively are
T3 and T1. Show that for the maximum work the ratio of compression should have the
value
( )
( ) or
( ) or
( )
are constants
( ) ( )
15. An engine working on otto cycle in which the salient points are 1,2,3 and 4 has upper and
lower temperature limits T3 and T1. If the maximum work per kg of air is to be done, show
that the intermediate temperatures are given by T2=T4=√
But ( ) from problem 14.
(( ) )
( )
T4=√
But ( ) from problem 14.
[( ) ]
T2=√
T2=T4=√
NUMERICALS :
1. The minimum pressure and temperature of the air standard Carnot cycle are 1 bar and
15oC respectively. The pressure after isothermal compression is 3.5 bar and the pressure
after isentropic compression is 10.5 bar. Determine i) Efficiency ii) Mean effective
pressure and the Power developed if the Carnot engine makes 2 cycles/s. Take for air
R=.287kJ/kgK and γ=1.4 (May June 2010)
T 2 3
2
3
P
4
1 1
4
S
V
Given:
The minimum pressure and temperature of the air standard Carnot cycle are 1 bar and 15 oC
respectively. P4=1bar; =288K
The pressure after isothermal compression is 3.5 bar, P1=3.5bar
the pressure after isentropic compression is 10.5 bar. P2=10.5bar
=288K
1-2 Process adiabatic
( ) ; ( )
Ie
Work Net /kg=
2-3 process
= =
3-4 process
=
( ) ---------1
( ) ---------------2
From 1 and 2
( ) ( )
ie
2-3 Process is Isothermal
; ; ;
4-1 Process is Isothermal
; ; ; .5
=1x0.287x394.2 x =141.73 kJ/kg
=1x0.287x288 x = 103.54 kJ/kg
Wnet= 141. 103.54 = 38.19kJ/kg
0.82656 m3/kg
0.10778 m3/kg
= = 46.57kPa
2. A petrol engine works on Otto cycle under ideal conditions. The initial pressure before
the beginning of compression is 101kPa at 340K. The pressure at the end of heat addition
process is 3.5Mpa. As per the details furnished by the manufacturer engine has stroke
length twice the bore. Engine bore is 300mm and clearance volume 4x10-3m3. Determine:
i) compression ratio ii) The air standard efficiency iii) the mean effective pressure (Dec
09- Jan10).
Given:
The initial pressure before the beginning of compression is 101kPa at 340K.
P1=101kPa,T1=340K,
The pressure at the end of heat addition process is 3.5Mpa.
P3=3.5Mpa =35bar,
As per the details furnished by the manufacturer engine has stroke length twice the bore L=2d,
Engine bore is 300mm and clearance volume 4x10-3m3.
D=0.3m,Vc=4x10-3m3.
V s= = =0.0424m3
=11.6
; =( ) ;
Alternative Method
; ;
; ;
1.4
1.01x11.6 =31.22 bar
=340x11.61.4-1=906.27K
35bar(given)
35=
Explosion ratio, 1.12
=1015.02K
;
= =0.6248 ie
=
( ) ( )
=0.547 bar=54.7kPa
3. From PV diagram of an engine working on otto cycle, it is found that the pressure in the
cylinder after 1/8th of the compression stroke is executed is 1.4 bar. After 5/8th of the
compression stroke, the pressure is 3.5 bar. Compute the compression ratio and the air standard
efficiency. Also if the maximum cycle temperature is limited to 1000oC, find the network output
(Jan/Feb2005)
Solution: the maximum cycle temperature is limited to 1000oC ie T3=1000oC
the pressure in the cylinder after 1/8th of the compression stroke is executed is 1.4 bar
Compression process 12 starts from 1 Let ‘a ‘ the point on the curve 12 after 1/8th of the compression
stroke and =1.4 bar
Ie refering from origin of pv diagram where =
where as
After 5/8th of the compression stroke, the pressure is 3.5 bar
Let ‘b ‘ the point on the curve 12 after 5/8th of the compression stroke and =3.5bar
a to b is adiabatic process
( ) ( )
( )
( )
ie =1.924 ;
+1.924
Alternative method
; ;
; ;
From fig, refering from origin of pv diagram where =
( ) ( )
( )
( )
ie =1.924 ;
+1.924
1x7.011.4=15.24 bar
=300x7.011.4-1=653.37K
; Explosion ratio,
=
= =0.541 ie
=
( ) ( )
=3.26 bar
4. An engine working on otto cycle rejects 535kJ/kg and has an air standard efficiency of
52% the pressure and temperature of the air at the compression are 1 bar and 50 oC. Compute (i)
The compression ratio of an engine (ii) The work done per kg of air (iii) The pressure and
temperature at the end of compression and (iv) The minimum pressure in the cycle
Given:,
An engine working on otto cycle rejects 535kJ/kg ie QR=535kJ/kg
has an air standard efficiency of 52% efficiency=0.52,
The pressure and temperature of the air at the compression are 1 bar and 50oC.
P1=100kPa,T1=323K
; ; Rc=6.27
; ; T4=1068.12K
; ; T3=2226K
579.95kJ/kg
=
( ) ( )
=7.44bar
5. If an engine works on Otto cycle between temperature limits 1450K and 310K. Find the
maximum power developed by the engine assuming the circulation of air per minute as
0.38kg/min.
If an engine works on Otto cycle between temperature limits 1450K and 310K
Ie T3 =1450K and T1=310K
For maximum work, ( )
( )
1450= ; 2.1625
; 670.4
Alternatively
[ ]
6. A four stroke four cylinder petrol engine of 250mm bore and 375 mm stroke works on
the Otto cycle. The clearance volume is 0.01052m3. The initial pressure and temperature
are 1 bar and 470C. If the maximum pressure is limited to 25 bar, find the following: air
standard efficiency and mean effective pressure.(Dec2011).
A four stroke four cylinder petrol engine of 250mm bore and 375 mm stroke ie D=0.25m ,L =0.375m
The clearance volume is 0.01052m3 Vc=0.01052m3
V s= = =0.0184m3
=2.75
Alternative method
; ;
; ;
V s= = =0.0184m3
=2.75
1x2.751.4=4.12 bar
=320x2.751.4-1=479.60K
;
;
=
;
= =0.3329 ie
=
( ) ( )
=10.60 bar
7. A four stroke four cylinder petrol engine of 250mm bore and 375 mm stroke works on
the Otto cycle. The clearance volume is 0.00263m3. The initial pressure and temperature are 1
bar and 500C. If the maximum pressure is limited to 25 bar, find the following: air standard
efficiency and mean effective pressure.(July2011).
A four stroke four cylinder petrol engine of 250mm bore and 375 mm stroke ie D=0.250m L=0.375m
V s= = =0.0184m3
=8
Alternative method
; ;
; ;
V s= = =0.0184m3
=8
1x81.4=18.38 bar
=323x81.4-1=742.05K
= Explosion ratio, 1.36
;
= =0.564 ie
=
( ) ( )
=1.34 bar
8. In an air standard diesel cycle, the compression ratio is 16. At the beginning of isentropic
compression, the temperature is 15o C and pressure is 0.1 Mpa. Heat is added until the
temperature at the end of the constant pressure process is 1480oC . Calculate i) cut off ratio ii)
heat supplied per kg of air iii) cycle efficiency and iv) mean effective pressure (Dec08/09)
the compression ratio is 16. Ie Rc=16
At the beginning of isentropic compression, the temperature is 15o C and pressure is 0.1 Mpa ie T1=15oC
and p1=1 bar=100kPa
Heat is added until the temperature at the end of the constant pressure process is 1480oC ie T3=1480oC
* +
* +
* +
[ ]
Mean effective Pressure=498.35kPa
9. Two engines are to operate on otto and diesel cycles with the following data. Maximum
temperature: 1400K, Exhaust temperature: 700K. State of air at the beginning of compression
0.1Mpa, 300K. Estimate the compression ratio, the maximum pressures, efficiencies and rate of
work output (for I kg/s of air) of the respective cycles (June/July08)
Otto cycle
Maximum temperature: 1400K, Exhaust temperature: 700K. Ie T3=1400K T4=700K
( ) ( )
Compression ratio =5.66

=2641.33kPa
[ ]
; ;
; ;
(Given)
( ) ( )
700= ; explosion ratio,

K
= =0.50 ie
Diesel Cycle
Maximum temperature: 1400K, Exhaust temperature: 700K. Ie T3=1400K T4=700K
700=300
Cut off ratio, ( ) ( )
( )
( ) ( )
Max pressure P3= P2=
* +
* +
[ ]
Note you can apply direct formula to find out temperatures and pressures
; ;
; ;
(Given)
Expansion ratio, ( ) ( )
in an Diesel cycle
700= x300
( )
1x10.361.4
= =0.5504 ie
10. The minimum and maximum temperatures in an engine working on constant pressure
cycle are 300K and 1500K and the heat addition during combustion is 500kJ/kg of air. Another
engine working on semi diesel cycle between the same temperature limits of 300K and 1500K
has a heat addition of 500kJ/kg of air which is shared equally between the two heat addition
processes. Compare their – i) Efficiencies and ii) Work outputs (Dec07/Jan08)
The minimum and maximum temperatures in an engine working on constant pressure cycle are 300K
and 1500K ie T1=300K, T3=1500K
the heat addition during combustion is 500kJ/kg of air
T2=1002.5K
( ) ( )
* +
* +
[ ]
; ;
; ;
he heat addition during combustion is 500kJ/kg of air
; T2=1002.5K
1002.5=300 ;
( )
=1.765bar
= =0.6731 ie
The minimum and maximum temperatures in an engine working on constant pressure cycle are 300K
and 1500K ie T1=300K, T4=1500K
a heat addition of 500kJ/kg of air which is shared equally between the two heat addition processes
ie =500
Hence
T3=1251.24K
T2=903.1K
( ) ( )
* +
* +
[ ]
[ ]
; ;
; ;
a heat addition of 500kJ/kg of air which is shared equally between the two heat addition processes
ie =500
Hence
T3=1251.24K
T2=903.1K
300
( )
1251.24 ;
;1500= ; cut off ratio =1.19
534.24
; ;
= =0.669 ie
11. The stroke and cylinder diameter of a compression ignition engine working on theoretical
diesel cycle are 250mm and 150mm respectively. The clearance volume is 0.0004m3. The fuel
injection at constant pressure takes place for 5% of the stroke. Calculate the efficiency of the
engine.
The stroke and cylinder diameter of a compression ignition engine working on theoretical diesel
cycle are 250mm and 150mm respectively. Ie D=0.25m, L=0.15m
The clearance volume is 0.0004m3 Vc=0.004m3
The fuel injection at constant pressure takes place for 5% of the stroke. K=5
V s= = =0.0044m3
=12
* +
* +
12. An indicator diagram taken on diesel engine shows that the compression curve follows
the law PV1.4 = Constant. At two points lying on the compression curve 1/8th and 7/8th of the
stroke the pressures are 1.6 bar and 16 bar respectively. Find the compression ration of the
engine. If cut off occurs at 6% of the stroke, calculate air standard efficiency of the engine
(June/July2009)
An indicator diagram taken on diesel engine shows that the compression curve follows the law PV1.4 =
Constant. Ie compression is adiabatic since n=1.4=
At two points lying on the compression curve 1/8th and 7/8th of the stroke the pressures are 1.6 bar and
16 bar respectively.
From fig,
( ) ( )
( )
( ( )) =
0.228Vs=4.18Vc
* +
* +
13. An air standard diesel cycle has a compression ratio of 16. The compression ratio of 16.
The temperature before compression is 27oC and the temperature after expansion is 627oC.
Determine (i) The network output per unit mass of air (ii) Thermal efficiency (iii) Specific air
consumption in kg/kWh (July/Aug 2005)
An air standard diesel cycle has a compression ratio of 16. Ie
The temperature before compression is 27oC and the temperature after expansion is
627oC.T1=27oC T4=627oC
( ) ( )
T3=909.4x2.19=1993.22K
[ ]
SFC=(3600/Wnet)=(3600/658.44)=5.47kg/kWh
14. An air standard limited pressure cycle has a compression has a compression ratio of 15
and compression begins at 0.1MPa,40oC. The maximum pressure is limited to 6MPa and the heat
added is 1.675MJ/kg. Compute (i) the heat supplied at constant volume per kg of air ii) the heat
supplied at constant pressure per kg of air (iii) the work done per kg of air (iv) the cycle
efficiency (v) the cut-off ratio (vi) m.e.p of the cycle (July07)
3 4
P 4
T P=C
3
V=C
2
5
2 5
1
1
V S
An air standard limited pressure cycle has a compression has a compression ratio of 15 and compression
begins at 0.1MPa,40oC ,
Also,
T3=1248.28K
[ ]
[ ]
T4=2683.74K
[ ]
[ ]
* +
* +
* ( ) +
[ ( ) ]
MEP=1200kPa
; ;
; ;
; ;
kJ/kg (given)
1675=232.35+ ; /kg
; 1442.65 ;
=ρ ; ρ
; ;
= =0.6052ie
=
( ) ( )
=12.09 bar
15. An ideal diesel engine has a compression ratio of 20 and uses air as the working fluid.
The state of air at the beginning of the compression process is 95kPa and 20oC. If the maximum
temperature in the cycle is not to exceed 2200K, determine (i) the thermal efficiency (ii) the
mean effective pressure. Assume constant specific heats for air at room temperature. (Dec /2010)
An ideal diesel engine has a compression ratio of 20
The state of air at the beginning of the compression process is 95kPa and 20oC
ie
T4=293x2.271.4=923.2K
[ ]
* +
[ ]
; ;
; ;
T4=293x2.271.4=923.2K
; =1235kJ/kg
= =0.6336ie
=
( ) ( )
=9.79 bar
16. An engine working on dual combustion cycle takes in air at 1 bar and 30oC. The
clearance is 8% of the stroke and cut-off takes place at 10% of the stroke. The maximum
pressure in the cycle is limited to 70bar. Find (i) temperatures and pressure at salient points; (ii)
air standard efficiency (March 2001)
3 4
P 4
T P=C
3
V=C
2
5
2 5
1
1
V S
An engine working on dual combustion cycle takes in air at 1 bar and 30oC. ie
The clearance is 8% of the stroke.Vc=0.08Vs
cut-off takes place at 10% of the stroke.K= V4 =0.01Vs
The maximum pressure in the cycle is limited to 70bar.P2 =P3 = 70bar

Tx=858.18x1.83=1570.47K
T3=1570.4x2.25=3533.56K
( )
P4=6.02bar
* +
* +
; ;
; ;
;
; ;
; ;
= =0.588ie
=
( ) ( )
=15.66 bar
17. The following data refers to an ideal sterling cycle with ideal regenerator. Pressure,
temperature and volume of the working medium at the beginning of the isothermal compression
are 100kPa, 30oC and 0.05m3 respectively. The clearance volume of the cycle is 1/10 of initial
volume. The maximum temperature attained in the cycle is 700oC. Draw PV and T-S diagrams
Calculate i) The network ii) Thermal efficiency with 100% regenerator efficiency iii) Thermal
efficiency without regenerator (June –July 2009)
Vs=0.05-0.005=0.045m3
(or
Without regenerator heat added is
Q=Q41+Q12
65.19kJ
Efficiency=(25.6/65.19)=39.26%
18. A mass of 1kg of air is taken through a diesel cycle and a joule cycle closed initially the
air is at 288K and 1.01325 bar. The compression ratio for both cycles is 15, and the heat added is
1850kJ in each case. Calculate the ideal cycle efficiency and mean effective pressure for each
cycle. Comment on the cycle ( June/July08)
T3=2691.6K
* +
* +
* +
[ ]
; ;
; ;
; T3=2691.6K
T4=288x3.161.4=1441.96K
kJ/kg(given)
;
= =0.552 ie
=
( ) ( )
=13.24 bar
Joule cycle:
T3=2691.6K
19. An oil engine works on the dual combustion cycle, the compression ratio is 10 and
expansion ratio is 5.5. The initial pressure and temperature of the air are 1 bar and 30 oC . The
heat liberated at constant pressure is twice the heat liberate at constant volume. The expansion
and compression follows the law PV1.3=C, Find the following (i) pressure and temperature at all
salient points (ii) mean effective pressure (iii) air standard efficiency (iv) Power developed if the
working cycle are 500/min and cylinder diameter is 24cm and stroke length is 40cm.
3 4
P 4
T P=C
3
V=C
2
5
2 5
1
1
V S
The expansion and compression follows the law PV1.3=C, ie =1.3

; ;
; ;
Given =2
1.005 =1.436
T3=1418.77K
P3=19.9526x2.34; P3=46.68bar
T4=1.82 =2582.16K
=1548.37K
; 5.08bar
; ;
; ;
; ; ;
=
( ) ( )
V s= for 4 stroke engine
Assuming 2 stroke engine
Vs = =0.1507m3/s
Power= ̇ Power=0.173x1034.93=179.04kW
20. The compression ratio for a single cylinder engine operating on dual cycle is 8. The
maximum pressure in the cycle is limited to 55 bar. The pressure and temperature of the air at the
beginning of the cycle are 1 bar and 270C. Heat assed during constant pressure process upto 3%
of the stroke. Assuming the diameter as 25cm and stroke as 30 cm find the following, the work
done per cycle, air standard efficiency and power if number of working cycles are
200/min.(June2012).
3 4
P 4
T P=C
3
V=C
2
5
2 5
1
1
V S
P3=55bar
Also ie
T3=2.99x689.3=2061K
Also ie
T4=1.21x2061=2493.82K
* +
* +
[ ]
[〈 〉 ]
V1= = =0.0147m3
Work/cycle=0.017x794.1=13.58kJ/cycle
Power=13.58x (200/60)=45.25kW
; ;
; ;
P3=55bar
2061K
;
; ;
; ;
; ;
= =0.559 ie
=
( ) ( )
=5.27bar
V s= for 4 stroke engine
Assuming 2 stroke engine
Vs = =0.049m3/s
Power= ̇ Power=0.056x794.22=44.47kW
3 4
P 4
T P=C
3
V=C
2
5
2 5
1
1
V S
1. Explain with sketch and T-S diagram explain open gas turbine cycle
Gas turbines are prime movers producing mechanical power from the heat generated by the
combustion of fuels. They are used in aircraft, some automobile units, industrial installations and
small – sized electrical power generating units. A schematic diagram, P-V and T-S diagrams of a
open cycle gas turbine power plant is shown above.
1-2: Reversible adiabatic compression.
2–3: Reversible constant pressure heat addition.
3–4: Reversible adiabatic expansion.
4–1: Reversible constant pressure heat rejection
2. Explain with sketch and T-S diagram explain closed gas turbine cycle
1
A schematic diagram, P-V and T-S diagrams of a closed cycle gas turbine power plant is shown
above.
1-2 : Reversible adiabatic compression.
2–3: Reversible constant pressure heat addition.
3 – 4: Reversible adiabatic expansion.
4–1: Reversible constant pressure heat rejection.
3. Differentiate between closed and open gas turbine cycle

Advantages of closed cycle over open cycle gas turbine
1. Higher thermal efficiency
2. Reduced size
3. No contamination
4. Improved heat transmission
5. Improved part load 
6. Lesser fluid friction
7. No loss of working medium
8. Greater output and
9. Inexpensive fuel.
Disadvantages of closed cycle over open cycle gas turbine

1. Complexity
2. Large amount of cooling water is required. This limits its use of stationary installation or
marine use
3. Dependent system
4. The wt of the system pre kW developed is high comparatively, therefore not economical
for moving vehicles
5. Requires the use of a very large air heater.
4. Derive an expression for efficiency of ideal brayton cycle.
2
( )
( ) ( )
or
5. Derive an expression for the work output of a gas turbine in terms of pressure ratio for
maximum and minimum temperatures T3 and T1 Henceshow that the pressure ratio for
maximum specific work output is given by Rw=( ) (Dec09/Jan10)
Or Derive an expression of optimum pressure ration for maximum net work output in an
ideal Brayton cycle. What is the corresponding cycle efficiency? (June/July08)
The variation of network output Wnet with pressure ratio rp is shown below.
From figure as rp increases from 1 to (rp)max, Wnet increases from zero, reaches a maximum at
an optimum value of rp i.e., (rp)opt and with further increase in rp, it reduces and becomes zero
when rp = rpmax
( ) or
( ) or
3
( )
, let
( )
( )
Therefore
[( ) ]
( )
6. Define work ratio in gas turbine and prove rw=1-
* +
4
7. Explain with sketch and T-S diagram explain actual gas turbine cycle
In the ideal Brayton cycle, compression and expansion of air are assumed to be reversible and
adiabatic. In reality, however, irreversibility’s do exist in the machine operations, Hence the
compression and expansion processes are not really constant entropy processes. Entropy tends to
be increase (as per the principle of increase of entropy).
8. Draw neat line diagram and T-S diagram for the following G.T cycle i) Regeneration ii)
Intercooling iii) Reheating (june-July 09)
9. Explain with neat sketch and T-S diagram Explain i) Regeneration ii) Intercooling iii)
Reheating, and derive an expressions for efficiency
1. Intercooling:
In this arrangement, compression of air is carried out in two or more stages with cooling of the
air in between the stages. The cooling takes place in a heat exchanger using some external
cooling medium. Figure shows the T-S diagram of a gas turbine plant with two-stage
compression with inter cooling.
[ ]
If air is cooled to a temperature equal to the initial temperature (i.e., if T 3=T1), inter cooling is
said to be perfect.
5
2. Reheating :
Here expansion of working fluid (air) is carried out in 2 or more stages with heating (called
reheating) in between stages. The reheating is done in heat exchangers called Reheaters.The
expansion takes place in two turbine stages, with reheating in between, are shown.Multi-Stage
expansion with reheating, by itself, and does not lead to any improvement in cycle efficiency. In
fact, it only reduces.
3.Regenerator :
The efficiency of the Brayton cycle can be increased by utilizing part of the energy of exhaust air
from the turbine to preheat the air leaving the compressor, in a heat exchanger called regenerator.
This reduces the amount of heat supplied Q1from an external source, and also the amount of heat
rejected Q2 to an external sink, by an equal amount. Since Wnet = Q1 - Q2 and both Q1 and Q2
reduce by equal amounts, there will be no change in the work output of the cycle.Regeneration
can be used only if the temperature of air leaving the turbine at 4 is greater than that of air
leaving the compressor at 2.
, regenerator effectiveness
In practice, a regenerator is expensive, heavy and bulky and causes pressure losses, which may
even decrease the cycle efficiency, instead of increasing it.
10. Derive an expression of optimum pressure ration for maximum net work output in an
actual Brayton cycle.
6
( ) or
( ) or
( )
, let
( )
( )
11.Explain the following
1. Turbojet engine:
This engine has a diffuser at inlet, the air entering experiences the ram effect due to diffuser and
its pressure is increased then the air enters the compressor and is compressed. The compressed
7
air enters the combustion chamber where fuel is added and hot gases at high pressure are
expanded through turbine which develops work needed for compressor. Then the gases are
expanded through the exit nozzle to develop the required thrust.
2. Turbo Fan engine
Turbofan engine is the modified turbojet engine in which additional thrust is realised by putting
fan at the entry of the engine casing. Fan blades propel by pass air around engine core between
inner and outer engine casing. This air does not participate in combustion but provides additional
thrust while leaving through exit nozzle. one air stream gets rammed, compressed, burnt,
expanded in turbine and finally passes through exit nozzle and other air stream passes through
passage between outer and inner casings from inlet to nozzle exit. Total thrust created will be
due to two jet streams one due to cold air or fan air and other due to burnt gases leaving turbine.
3. Turbo prop engine
Turboprop (Turbo-propeller) engine differs slightly from turbofan engine. It uses thrust to turn a
propeller. A part of turbine output is used to drive the compressor and remaining for driving
propeller. Turboprop engines are used in small passenger planes and cargo planes.
4. Ramjet engine
Ramjet engine is the simplest of jet engines having no moving parts. Ramjet is a typically shaped
duct open at both ends with air being compressed merely due to forward motion of engine. Fuel
8
is subsequently added for combustion and thus high pressure, high temperature gases exit from
exhaust nozzle.
5. Pulse jet engine
It is quite similar to ramjet engine except the difference that pulse jet employs a non-return type
mechanical valve of V-type for preventing flow of hot gases through diffuser. Pulse jet engine
has diffuser section in which ram compression occurs and after diffuser section a grid of non-
return valves is put for maintaining intermittent flow of compressed air.
6. Rocket propulsion
The Oxidizer and fuel stored separately in tanks are pumped through a common control valve to
combustion chamber and then the hot gases are exhausted to atmosphere through the nozzle
providing thrust to the rocket.
NUMERICALS:
1. Air enters the compressor of an ideal standard Brayton cycle at 100kPa, 300K with a
volumetric flow rate of 6m3/s. The compressor pressure ratio is 10. The turbine inlet
temperature is 1500K. Determine i) The thermal efficiency ii) work ratio iii) The power
developed.(June-July09)
9
Air enters the compressor of an ideal standard Brayton cycle at 100kPa, 300K
T1=300K, P1=100kPa,
volumetric flow rate of 6m3/s ie Vf=6m3/s
The compressor pressure ratio is 10. Ie ,
The turbine inlet temperature is 1500K. Ie T3=1500K
{ } ; { } ; T2 = 579.2K
{ } ; { } , T4 = 776.9K
( )
( )
Here assume Since Air fuel ratio or Calorific value of fuel is not given
Hence efficiency equation becomes

;
= 0.482 or 48.2%
Net work output WT  WC
Work ratio = WR  
Turbine work WT
= 0.62
P= WT  WC =( )
Here assume Since Air fuel ratio or Calorific value of fuel is not given
P=
10
volumetric flow rate of air 6m3/s ie Vf =6m3/s R
( )
= =6.96kg/s Note R for air =0.287kJ/kgK
= 3089.54kW
2. A gas turbine power plant operates on the simple Brayton cycle with air as working fluid and
delivers 32MW of power. The minimum and maximum temperatures in the cycle are 310 and
900K, and pressure of air at the compressor exit is 8 times the value at the compressor inlet.
Assuming an isentropic efficiency of 80% for the compressor and 86% for the turbine, determine
the mass flow rate of air through the cycle (June/July08)
delivers 32MW of power. ie P=32MW=32000kW

The minimum and maximum temperatures in the cycle are 310 and 900K, ie T1=310K, T3=900K
pressure of air at the compressor exit is 8 times the value at the compressor inlet.
ie
Assuming an isentropic efficiency of 80% for the compressor and 86% for the turbine,
𝞰c=0.8,𝞰t=0.86,
1-2s is adiabatic
{ } ; ; T2s = 561.5K
, T2 = 624.37K
3-4s adiabatic process
{ } ; , T4s = 496.8K
, T4 = 553.25K
Here also assume Since Air fuel ratio or Calorific value of fuel is not given
Hence efficiency equation becomes
11
;
= 0.117 or 11.7%
( )
( )
m=983.34kg/s
3.In a gas turbine plant the intake temperature and pressure are 18oC and 1 bar respectively. Air
is compressed to a pressure of 4.2 bar by a compressor. The isentropic efficiency of compressor
is 84%. Gas is heated to 650oC in the combustion chamber, where there is a pressure drop of
0.086 bar. The expansion of gas then occurs to atmospheric pressure in the turbine. The thermal
efficiency of plant is 18%. Draw the T-S diagram and find the isentropic efficiency of the
turbine. Neglect mass of fuel and take properties of gas as that of air. (May/June2010)
the intake temperature and pressure are 18oC and 1 bar respectively.
T1=18oC =291K,
Air is compressed to a pressure of 4.2 bar by a compressor ie bar
,
The isentropic efficiency of compressor is 84%.,ie 𝞰c=0.84,
Gas is heated to 650oC in the combustion chamber, where there is a pressure drop of 0.086 bar.
Ie T3=650oC =923K ;
Pressure drop in the combustion chamber is 0.086 bar ie ie 0.086
The thermal efficiency of plant is 18%. ie =0.18
Neglect mass of fuel and take properties of gas as that of air. ; R for gas =R for air
=0.287kJ/kgK
find the isentropic efficiency of the turbine. 𝞰t=?
ie
12
1-2s is adiabatic process
{ } ; ; T2s = 438.5K
, T2 = 466.6K
Note that here not equal to as there is combustion chamber loss
0.086= 0.086=4.114 bar
{ } ; { } , T4s = 616.2K
Actual temperature at 4 , T4 = 665.25K
;
4.In an open cycle gas turbine plant air enters the compressor at 1 bar and 27oC. The pressure
after compression is 4 bar. The isentropic efficiencies of the turbine and the compressor are 85%
and 80% respectively. Air fuel ratio is 80:1. Calorific value of the fuel use is 42000 kJ/kg. Mass
flow rate of air is 2.5kg/s. Determine the power output from the plant and the cycle efficiency.
Assume that Cp and γ to be the same for both air and products of combustion (Dec09/
Jan10/June2012old)
air enters the compressor at 1 bar and 27oC. Ie T1=300K,

The pressure after compression is 4 bar. Ie ,
The isentropic efficiencies of the turbine and the compressor are 85% and 80% respectively.
𝞰t=0.85, 𝞰c=0.8,
air fuel ratio=80, ie =80
Calorific value of the fuel use is 42000 kJ/kg; .CV=42000kJ/kg,
13
Mass flow rate of air is 2.5kg/s. Ie =2.5kg/s
Determine the power output from the plant and the cycle efficiency. P=?
Assume that Cp and γ to be the same for both air and products of combustion
ie Cpg= Cpa=1.005kJ/kgK; =1.4
=
{ } ; ; T2s = 445.8K
, T2 = 482.25K
( )
( )
T3 = 998.2K
3-4s isentropic as there is no combustion chamber loss
{ } ; , T4s = 671.7K
, T4 = 720.7K
;
=2.5kg/s
AF =80(given) ie ie
( )
= 0.1846 or 18.46%
( )
( )
(( ) ) = 247.99kW
5.In a simple gas turbine unit, the isentropic discharge temperature of air flowing out of the
compressor is 195oC, while the actual discharge temperature is 240oC. Air conditions at the
compression inlet are 1 bar and 17oC. If the air fuel ratio is 75 and net power output from the unit
is 650kW. Compute i) isentropic efficiencies of the compressor and the turbine and ii) Overall
cycle efficiency. Calorific value of the fuel used is 46110kJ/kg and the unit consumes 312kg/hr
14
of fuel. Assume Cp for gases 1.09kJ/kg-K and γ=1.32 and for air Cp=1.005kJ/kg-K and γ=1.4
(Feb 2005)
In a simple gas turbine unit, the isentropic discharge temperature of air flowing out of the
compressor is 195oC, while the actual discharge temperature is 240oC
Ie T2s=195oC =195+273=468K ; T2=240oC =240+273=513K
Air conditions at the compression inlet are 1 bar and 17oC. Ie P1=1 bar; T1=290K;
air fuel ratio=75,
net power output from the unit is 650kW. P=650kW
Compute i) isentropic efficiencies of the compressor and the turbine and ii) Overall cycle
efficiency. I) ii)
Calorific value of the fuel used is 46110kJ/kg ie CV=46110kJ/kg, ,
the unit consumes 312kg/hr of fuel. =312k/hr =0.087kg/s
Assume Cp for gases 1.09kJ/kg-K and γ=1.32 and for air Cp=1.005kJ/kg-K and γ=1.4,
Cpg=1.09kJ/kgK, γg=1.32,
Cpa=1.005kJ/kgK, γa=1.4
{ } ; { } ; { }
5.34
=0.8
( )
( )
; T3 = 1069.6K
{ } ; where =1.32
Note that here is not equal to since in the problem and are separately given
In all previous problems we assumed
, T4s = 712.6K
15
( )
( )
T4 = 776.6K
( )
=0.162 or 16.2%
6.A gas turbine plant draws in air at 1.013 bar,10oC and has a pressure ratio of 5.5. The
maximum temperature in the cycle is limited to 750oC. Compression is conducted in an uncooled
rotary compressor having an efficiency of 82% and expansion takes place in a turbine with an
isentropic of 85%. A heat exchanger with efficiency 70% is fitted between the compressor outlet
and combustion chamber. For an air flow of 40kg/s, find i) Overall efficiency of cycle ii) Turbine
output iii) Air fuel ratio if the calorific value of the fuel used is 45.22MJ/kg (Dec 08/Jan09)
A gas turbine plant draws in air at 1.013 bar,10oC ie , T1=283K

has a pressure ratio of 5.5 ie ,
The maximum temperature in the cycle is limited to 750oC ie T3=1023K,
Compression is conducted in an uncooled rotary compressor having an efficiency of 82% and
expansion takes place in a turbine with an isentropic of 85%. 𝞰c=0.82,𝞰t=0.85,
A heat exchanger with efficiency 70% is fitted between the compressor outlet and combustion
chamber ε = 0.7,
For an air flow of 40kg/s,ma=40kg/s,
Air fuel ratio if the calorific value of the fuel used is 45.22MJ/kg AF=? CV=45220kJ/kgK
1-2s Adiabatic process
{ } ; ; T2s = 460.6K
, T2 = 499.6K
3-4s is adiabatic process
16
{ } ; , T4s = 628.6K
as there is no combustion chamber loss =5.5
, T4 = 687.8K
; T5 = 631.34K
( )
( ) ;
( )
( )
ie ie kg/s
Assume =1.005kJ/kgK as
Turbine Output = 13592.95KW

Heat supplied = as 2-3 air is heated by exhaust gases
as
= 0.3028 or 30.28%
7. A gas turbine plant operates on ideal Brayton cycle. The minimum and maximum cycle
temperature are respectively T1=300K and T3= 800K. Find the value of the optimum pressure
ratio for maximum specific work output and cycle efficiency for this condition. Is it possible
to improve this cycle efficiency by including a regenerator substantiate? (jan/Feb 06)
Data: T1=300K and T3= 800K
Find the value of the optimum pressure ratio for maximum specific work output and cycle
efficiency for this condition =?

 T  2 1
For maximum work output pressure ratio= Ropt  3
 T1 
Hence for Maximum specific work output =( )
17

 T  2 1
Ropt  3
 T1 
( ) =5.57
{ } ; ;T2 = 490K
{ } assuming ; hence
, T4 = 489.76K
Since and is neglected above equation reduced to
= 0.3878 or 38.78%
As T4 = T2 , regenerator cannot be used ( for regenerator T4> T2)
7.A simple gas turbine plant operating on the Brayton cycle has air entering the compressor at
100kPa and 27oC. The pressure ratio=9.0 and maximum cycle temperature =727oC. What will be
the percentage change in cycle efficiency and network output if the expansion in the turbine is
divided into two stages each of pressure ratio 3, with intermediate reheating to 727oC?. Assume
compression and expansion is isentropic (july 2010)
air entering the compressor at 100kPa and 27oC. Ie P1=100kPa; T1=300K

The pressure ratio=9.0 ie ,
maximum cycle temperature =727oC, T3=1000K
First case is simple gas turbine cycle
In both cases and are not given
18
{ } ; ; T2s = 562K
T2 =T2s since is not given
{ } ; , T4s = 533.77K
T4=T4s since is not given
Here air fuel ratio or calorific value of fuel is not given Hence
Since and is neglected above equation reduced to
= 0.466 or 46.6%, Wnet=204kJ/kg

if the expansion in the turbine is divided into two stages each of pressure ratio 3, with
intermediate reheating to 727oC
= =3 and = 727oC=1000K
Calculation is same as case 1. Ie
Let intermediate pressure for turbine stages ie
{ }
, T4s = 730.6K ; T4 = 730.6K

as is not given
= T4=730.6K ( as T5=T3, and pressure ratio is same ie 3)
19
As is neglected and
= 0.3912 or 39.12%, Wnet=268kj/kg

8.In a reheat gas turbine cycle , comprising one compressor and two turbines, air is compressed
from 1 bar, 27oC to 6 bar. The highest temperature in the cycle is 900oC. The expansion in the
first stage turbine is such that the work from it just equals the work required by the compressor.
Air is reheated between the two stages of expansion to 850oC. Assume that the isentropic
efficiencies the first stage and the second stage turbines are 85% each and that the working
substance is air and calculate the cycle efficiency (June-July 2004/Dec2011)
In a reheat gas turbine cycle , comprising one compressor and two turbines,
= ;
=
air is compressed from 1 bar, 27oC to 6 bar T1=300K, P1=100kPa=1bar; hence
Air is reheated between the two stages of expansion to 850oC.T5=1123K,

Assume that the isentropic efficiencies the first stage and the second stage turbines are 85% each
𝞰t1= 𝞰t2=0.85,
Ie The expansion in the first stage turbine is such that the work from it just equals the work
required by the compressor wt1= wc
In the above problem the isentropic efficiency of the compressor is not given Hence assume
𝞰c= 100% ie
{ } ; ; T2 = 500.5K as 𝞰c= 100%

wt1= wc
=
as as given
20
1173-T4 = 500.5-300
T4=972.5K
; T4s = 937.12K
3-4s process is adiabatic
{ } ; { } ; { } ;
as
=2.19 ;
5-6s is isentropic
; ; T6s=842K
; T6 = 884.15K
As is neglected and
= 0.3136 or 31.36%,
9.A G.T. cycle having 2 stage compression with intercooling in between stages and 2 stages
of expansion with reheating in between the stages has an overall pressure ratio of 8. The
maximum cycle temperature is 14000K and the compressor inlet conditions are 1 bar and
270C. The compressors have s of 80% and turbines have s of 85%. Assuming that the air
is cooled back to its original temperature after the first stage compression and gas is reheated
back to its original temperature after 1st stage of expansion, determine (i) the net work output
(ii) the cycle th.
Data:
2 stage compression with intercooling in between stages and 2 stages of expansion with
reheating in between the stages ie 2 compressor with inter cooler and 2 turbine with reheater
P
overall pressure ratio of 8 ie 4  8bar
P1
= ;
21
=
The maximum cycle temperature is 14000K ie T5 = 14000K

the compressor inlet conditions are 1 bar and 270C. Ie P1= 1 bar ; T1 = 3000K
The compressors have s of 80% and turbines have s of 85%
Ie C1= 0.8 = C2, t1 = t2 = 0.85 ,
Assuming that the air is cooled back to its original temperature after the first stage
compression ie T3 = T1
and gas is reheated back to its original temperature after 1st stage of expansion, T7 = T5
P4
Solution:  8bar T5 = 14000K T1 = 3000K, P1= 1 bar
P1
C1= 0.8 = C2, t1 = t2 = 0.85 ,
T3 = T1 ;T7 = T5
also assume Since Air fuel ratio or Calorific value of fuel is not given
P2 P4 P5 P7 P4 P5
For maximum work output,       8
P1 P3 P6 P8 P1 P8
 Intermediate Pr essure, P2  P3  P6  P7  2.83 bar
 1
P  
For process 1-2s is adiabatic process, { } T2 s  T1  2 
 P1 
= 300 (2.83)0.286 = 403.950K
T2 s  T1 403.95  300
But  c1  0.8    T2  429.9 0 K
T2  T1 T2  300
22
P4 P2
Since T3 = T1 and 
P3 P1
We have T4s = T2s = 403.950K
Also since C1 = C2, T4 = T2 = 429.90K
Compressor work, WC = CPa (T2 – T1) + CPa (T4 – T3)

= 2 CP (T2 – T1)
= 2 (1.005) (429.9 – 300)
= 261.19 kJ/kg
For process 5 – 6,Adiabatic process
 1
T6 s  P6  
0.286
 1 
    T6 s  1400   1039.72 0 
T5  P5   2.83 
T  T6 1400  T6
But  t1  5 i.e., 0.85   T6  1093.76 0 K
T5  T6 s 1400  1039.72
P P
Since T7 = T5and 5  7 , then T8 = T6
P6 P8
Since t1 = t2, T6 = T8 = 1093.760K
Turbine work, Wt = CPg (T5 – T6) + CPg (T7 – T8)

= 2 CPg (T5 – T6)
= 2 (1.005) (1400 – 1093.76)
= 615.54 kJ/kg
Note CPg= CPa =1.005kJ/kgK as CPg is not given
WNet = WT – WC = 354.35 kJ/kg
th = ?
Heat Supplied, Qs = CPg (T5 – T4) + CPg (T7 – T6)

= 1.005 (1400 – 429.9 + 1400 – 1093.76)
= 1282.72 kJ/kg
354.35
 th  = 0.276 or 27.6%
1282.72
10.A two stage gas turbine cycle receives air at 100 kPa and 150C. The lower stage has a
pressure ratio of 3, while that for the upper stage is 4 for the compressor as well as the turbine.
The temperature rise of the air compressed in the lower stage is reduced by 80% by intercooling.
Also, a regenerator of 78% effectiveness is used. The upper temperature limit of the cycle is
11000C. The turbine and the compressor sare 86%. Calculate the mass flow rate required to
produce 6000kW.
23
Data
A two stage gas turbine cycle
Ie 2 compressor with inter cooling and 2 stage turbine with reheater
The lower stage has a pressure ratio of 3, 3
upper stage is 4 for the compressor as well as the turbine
4
The temperature rise of the air compressed in the lower stage is reduced by 80% by intercooling.
=0.8 ( )
Also, a regenerator of 78% effectiveness is used

The upper temperature limit of the cycle is 11000C ie T5=11000C=13730K
The turbine and the compressor sare 86%.ie C1 = C2 = t1 = t2 = 0.86
produce 6000kW ie P = 6000 kW
Solution: P1 = 1 bar T1 = 2880K

P2 P4
 3, 4 IC = 0.8
P1 P3
ε = reg = 0.78, T5 = 13730K, C1 = C2 = t1 = t2 = 0.86
  ? if P = 6000 kW
m
 1
T P  
Process 1-2s is isentropic compression  2 s   2 
T1  P1 
T2s = 288 (3) 0.286 0
= 410.75 K
T2 s  T1 410.75  288
But C1  i.e., 0.86  T2  430.73K
T2  T1 T2  288
T T 430.73  T3
Also,  IC  2 3 i.e., 0.8  T3  316.54 K
T2  T1 430.73  288
=0.8 ( ) (data)
430.73 ;
24
 1
T4 s  P4  
Process 3-4s is 2nd stage isentropic compression   
T3  P3 
T4s = 316.54 (4)0.286 = 470.57K
T4 s  T3 470.57  316.54
But C 2  i.e., 0.86  T4  495.64 K
T4  T3 T4  316.54
 1
T P  
Process 5-6s is 1st stage isentropic expansion  6 s   6 
T5  P5 
0.286
1
T6 s  1373   923.59 K
4
T  T6 1373  T6
But  t1  5 i.e., 0.86   T6  986.510 K
T5  T6 s 1373  923.59
Process 6-7 is reheating, assume T7 = T5 = 13730K
 1
T P  
Process 7-8s is 2nd stage isentropic expansion i.e., 8 s   8 
T7  P7 
0.286
1
 T8 s  1373   1002.79 0 K
 3
T  T8 1373  T8
But  t 2  7 i.e., 0.86   T8  1054.630 K
T7  T8 s 1373  1002.79
Tx  T4
Regenerator is used to utilizes the temperature of exhaust gases i.e., 
T8  T4
Tx  495.64
i.e., 0.78  Tx = 931.650K
1054.63  495.64
We have, Compressor work: WC = CPa (T2 – T1) + CPa (T4 – T3)
= 1.005 (430.73 – 288 + 495.64 – 316.54)
= 323.44 kJ/kg
Also, Turbine work : WT = CPg (T5 – T6) + CPg (T7 – T8)
= 1.005 (1373 – 986.51 + 1373 – 1054.63)
= 708.38 kJ/kg
Net work output, WN = WT - WC
= 384.95 kJ/kg
But, power produced, P  m  WN
i.e., 6000 x 1000 = m 384.95 x 1000
 m = 15.59 kg/sec
25
We have, heat supplied, Qs = CPg (T5 – Tx) + CPg (T7 – T6)
= 1.005 (1373 – 931.65 + 1373 – 986.51)
= 831.98 kJ/kg
W
 th  N  0.463 or 46.3%
QH
Note: CPg= CPa=1.005kJ/kgK as CPg is not given and
12 A gas turbine plant consists of two compressors with perfect inter cooling. The expansion
occurs in a single turbine. The mass flow rate of air through the plant is 1 kg/min. Calorific value
of the fuel used is 41870kJ/kg, maximum and minimum temperature in the cycle are 900oC and
27oC respectively. The working pressure limits are 1 bar and 6 bar. The compressors have
isentropic efficiencies of 80% and the turbine efficiency is 85%. The pressure ratios for both the
compressor stages are equal. The regenerator in the plant has effectiveness of 0.7. Determine i)
overall efficiency of the plant ii) the output from the plant in kW iii) air fuel ratio iv) work ratio
A gas turbine plant consists of two compressors with perfect inter cooling. The expansion occurs
in a single turbine
2 compressor and one turbine
= ;
with perfect inter cooling. =
The mass flow rate of air through the plant is 1 kg/min, ma=1 kg/min.
Calorific value of the fuel used is 41870kJ/kg, CV=41870kJ/kg
maximum and minimum temperature in the cycle are 900oC and 27oC respectively.
T1 =27oC=300K , T5 =9000C= 1173 K,
The working pressure limits are 1 bar and 6 bar.
P1 = P6 =1 bar,P4= P5 =6 bar,
The compressors have isentropic efficiencies of 80% and the turbine efficiency is 85%.
C = 0.8, t=0.85 ,.
The pressure ratios for both the compressor stages are equal
= ie
The regenerator in the plant has effectiveness of 0.7. ie ε = reg = 0.7
26
; =2.45
{ } ; ; T2s = 387.5K = T4s
, T2 = 409.37K= T4 as compression ratio , initial temperature of compression,

and efficiency for both compression are same
5-6s adiabatic compression
{ } ; , T6s = 703K
, T6 = 773.5K
; T7 = 664.26K
( )
( ) ;
( )
( )
;
kg/s
( ) [ ]
( )
( ) [ ]
( )
= 0.163 or 16.3%,
Out put: ( ) [ ]
P=( ) [ ]
P=3.03kW
( ) ( )
27
Turbine work WT
= 0.4529
13. In a gas turbine plant air is compressed at 15oC and at 1 bar with a pressure ratio of 6. The
air is heated in a heat exchanger with 75% efficiency and then in the combustion chamber to
750oC. The air at 750oC is expanded in two stages such that the expansion work is maximum.
The air is reheated to 750oC after the first stage. Determine the cycle thermal efficiency, the
work ratio and the net shaft work per kg. Take machine efficiencies as 80% and 85% for the
compressor and turbine efficiency
In a gas turbine plant air is compressed at 15oC and at 1 bar with a pressure ratio of 6.
T1=15oC=288K ; P1 = 1 bar,
a pressure ratio of 6 ie =6 bar,
The air is heated in a heat exchanger with 75% efficiency ie ε = reg = 0.75
in the combustion chamber to 750oC. Ie T5=750oC=1023 K
The air at 750oC is expanded in two stages such that the expansion work is maximum.
ie
The air is reheated to 750oC after the first stage T5=750oC =1023 K,
Take machine efficiencies as 80% and 85% for the compressor and turbine efficiency
c=0.80 ; t=0.85
√ =2.45
{ } ; ; T2s = 480.5K
; , T2 = 528.63K
{ } ; , T4s = 791.9K=T6s
; , T4= 826.56K
T6= T4= 826.56K as initial temperature, expansion ratio, and efficiency of both turbine are same
; T7 = 752.1K
28
As is neglected and
= 0.326 or 32.6%,
Net work Out put: [ ]
Net work Out put: [ ]
Output=152.25kj/kg
Turbine work =392.88kJ/kg
Turbine work WT
= 0.38
14. In a jet propulsion cycle air enters the compressor at 1 bar and 150C. The pressure leaving the
compressor is 5 bar and the maximum temperature is 9000C. The air expands in the turbine to
such a pressure that the turbine work is just equal to the compressor work. On leaving the
turbine, the air expands in a reversible adiabatic process in a nozzle to 1 bar. Calculate the
velocity of air leaving the nozzle.(June 2012)
{ }
T2 = 456.14K
T4=731.860C
29
{ }
{ }
P4=2.9 bar
{ }
T5 = 741.3K
√ √
30
Combustion Thermodynamics
Fuels: Fuel is defined as the combustible matter which combustion with oxygen generates heat.
Oxygen generally supplied by air.
Air mainly consists of O2 and N2 with composition 21% and 79% in volume respectively, and 23% and
77% in weight respectively.
Fuels mainly classified as i) Solid fuel ex: wood, Peat , coal ii) Liquid fuels: major source is Crude
petroleum oil such as paraffins CnH2n+2,Olifins CnH2n+1,Nepthalenes CnH2n and the Aromatics CnH2n-6
Gaseous fuel such as natural gas, Coal gas, water gas
Combustion: Combustion is a chemical reaction between a fuel and oxygen which proceeds at a
fast rate with the release of energy in the form of heat
CH4+2O2 CO2+2H2O
Reactants Products
Ie One mole of Methane reacts with 2 mole of oxygen to form of one mole of CO2 and 2 mole of H2O
Oxygen is supplied by air. Air mainly consists of O2 and N2 with composition 21% and 79% in volume
respectively ie in Air for each mole of Oxygen there are 3.76 moles of Nitrogen. Therefore above
reaction of methane with air may be written as follows
CH4+2O2+2(3.76) N2 CO2+2H2O+2(3.76) N2
Reactants Products
Total mole of air is 2+3.76x2 =9.52
Theoretical (Stoichiometric) Air for complete combustion of fuel:
Stoichiometric (theoretical Air required) is the minimum amount of air which required for the
complete combustion of all the elements like Carbon and Hydrogen etc.,
The minimum air fuel ratio required for the complete combustion of fuel is Stoichiometric air fuel
ratio
CH4+2O2+2(3.76) N2 CO2+2H2O+2(3.76) N2
Reactants Products
In the above reaction the Carbon in the CH4 react with oxygen in the air and forms CO2 and Hydrogen
in the CH4 reacts with Oxygen in the air and forms H2O (ie No CO and no O2 present in the products)
and hence combustion is complete.
In the above reaction for complete combustion of CH4 requires (2+2x3.76) moles of air
Hence Stoichiometric air fuel ratio on molal basis

7.52:1
Air fuel ration based on mass basis= = =16.66:1
Excess Air: In practical case of combustion if minimum air is supplied, due to improper mixing of air
and fuel and availability of less time for reaction combustion would not be complete. Hence,
excess air is supplied for ensuring complete combustion of fuel .
Excess air ensures better combustion but at the time keeps the furnace cool
Excess Air = Air supplied – Stoichiometric Air
Percentage of excess Air = x100
For example if 50% excess air is supplied for combustion of methane
CH4+1.5(2O2+2(3.76)) N2 CO2+2H2O+(0.5x2) O2 +1.5x(2(3.76)) N2
Air fuel Ratio:
Mass Basis
It is defined as the ratio of mass of air required to the mass of fuel for any combustion process
Mole Basis: It is defined as the ratio of no of moles of air supplied to the no of moles of fuel
Enthalpy of formation:
Enthalpy of a compound is defined as the enthalpy referred to a standard atmospheric pressure of 1

bar and temperature of 25oC at which the enthalpy of reactants which form the compound is
considered to be zero
Consider the steady state of steady flow combustion of carbon and oxygen to form CO2. Let the
carbon and oxygen each enter control volume at 25oC and 1 atm pressure and heat be such that the
product leaves at 25oC and 1 atm pressure. The measured value of heat transfer is -393,522kJ per kg
mol of CO2 formed.
If HR and HP refer to the total enthalpy of the reactants and products respectively, then the according
to Ist law of thermodynamics applied to the reaction C+O2 CO2 gives
HR + Q C.V = HP
The enthalpy of all the elements at the standard reference state of 25oC and 1 atm is assigned the
value of zero. Since C and O2 are elements enthalpy of reactants is zero
Hence Qc.v=-393,522kJ/kg mol
Hence enthalpy of formation of CO2 is is -393,522kJ per kg mol

Enthalpy of Combustion: is defined as the difference between the enthalpy of the products and the
enthalpy of the reactants when complete combustion occurs at a given temperature and pressure
̅̅̅̅̅ = HP- HR
̅̅̅̅̅ =∑ [ ( )] p -∑ [ ( )]R
Where np= Number of moles of products
nR= Number of moles of reactants
hf=enthalpy of formation
hT - h298 = enthalpy associated with its change in state from the standard state (15oC) to the
combustion temperature ToC at 1 atmosphere pressure
Internal Energy of Combustion : The internal energy of combustion is defined as difference between
the internal energy of the products and the internal energy of reactants after complete combustion
at a given temperature and pressure
̅̅̅̅̅ = UP- UR
̅̅̅̅̅ =∑ [ ( ) ̅] p -∑ [ ( ) ̅ ]R
Where np= Number of moles of products
nR= Number of moles of reactants
hf=enthalpy of formation
hT - h298 = enthalpy associated with its change in state from the standard state (15oC) to the
combustion temperature ToC at 1 atmosphere pressure
P is the pressure and ̅ is the molal volume
Adiabatic Flame Temperature: During combustion in a combustion chamber if the chemical reaction
goes to completion adiabatically, without work being performed by the system and without any
change in kinetic and potential energies during a steady flow process, the temperature of products
attained is called adiabatic flame temperature. Adiabatic flame temperature is maximum if the fuel
air mixture is stoichiomeric. Adiabatic flame temperature can be controlled by supplying excess air
HR= HP
∑ [ ( )]R=∑ [ ( )] p
Higher heating value: is the heat transferred when H2O in the products is in the liquid state.
Lower heating value is the heat transferred in the reaction when H2O in the vapour state
LHV=HHV-mH20-hfg
Wet and dry analysis of combustion: Combustion analysis when carried out considering water
vapour into account is called “wet analysis” while the analysis made on the assumption that vapour
is removed after condensing it, is called “dry analysis”.
Volumetric and gravimetric analysis: Combustion analysis when carried out based upon percentage
by volume of constituent reactants and products is called volumetric analysis.
Orsat apparatus for volumetric analysis
Flask I is filled with NaOH or KOH solution (about one part of KOH and 2 parts of water by mass). This
33% KOH solution shall be capable of absorbing about fifteen to twenty times its own volume of
CO2. Flask II is filled with alkaline solution of pyrogallic acid and above KOH solution. Here 5 gm of
pyrogallic acid powder is dissolved in 100 cc of KOH solution as in Flask I. It is capable of absorbing
twice its own volume of O2. Flask III is filled with a solution of cuprous chloride which can absorb CO
equal to it’s’ volume. Cuprous chloride solution is obtained by mixing 5 mg of copper oxide in 100 cc
of commercial HCl till it becomes colourless. Each flask has a valve over it and C1, C2, C3 valves are
put over flasks I, II and III. The flue gas for analysis is taken by opening the main valve C, while valves
C1, C2 and C3 are closed. 100 cc of flue gas may be taken into eudiometer tube by lowering aspirator
bottle until the level is zero. Aspirator bottle is lifted now so as to inject flue gas into flask I with only
valve C1 in open state where CO2 present shall be absorbed. Aspirator bottle is again lowered and
reading of eudiometer tube taken. Difference in readings of eudiometer tube initially and after CO2
absorption shall give percentage of CO2 by volume. Similar steps may be repeated for getting O2
and CO percentage by volume.
1. Methane (CH4) is burned with atmospheric air, The analysis of the products on a dry basis is
as follows:
CO2=10%, O2=2.37%, CO=0.53% and N2=87.10%. Calculate the air fuel ratio the percent of theoretical
air and write down the combustion equation (June /July08)
Solution
n CH4+aO2+3.76aN2 10CO2+2.37O2+0.53CO+87.10N2+dH2O
Carbon balance:
n=10+0.53=10.53
Nitrogen Balance:
3.76a =87.1
a=23.16
Oxygen Balance:
a =10+2.37+ +
23.16=10+2.37+ +
d=21.05
Chemical Equation
10.53 CH4+23.16O2+3.76(23.16)N2 10CO2+2.37O2+0.53CO+87.10N2+21.05H2O
Mass of fuel= nCH4xMCH4=10.53x16=168.48kg
Mass of Air= nO2xMO2+ nN2xMN2=23.16x32+(3.76x23.16)x28=3179.40
Actual Air fuel ratio= = =18.87:1
Stoichiometric Air fuel ratio
CH4+aO2+(3.76xa)N2 bCO2 +cH2O+(3.76xa)N2
Carbon balance
1=b
Hydrogen balance
4=2c ie c=2
Oxygen balance
2a=2b+c ie 2a=(2x1)+2 ; a=2
Hence the equation becomes
CH4+2O2+(3.76x2)N2 CO2 +2H2O+(3.76x2)N2
Mass of fuel= nCH4xMCH4=1x16=16kg
Mass of Air= nO2xMO2+ nN2xMN2=2x32+(3.76x2)x28=274.56kg
Theoretical Air fuel ratio= = =17.56:1
Actual air fuel ratio in percentage of theoretical : = =107.46%
2. Propane (C3H8) is burnt in atmospheric air and the mass analysis of the dry products of
combustion is as follows:
CO2---12.19% ; CO----1.23% ; O2----7.57% and the balance N2
Determine:
i) The volumetric analysis of the dry products
ii) Percent theoretical air
Solution
N2=100-(12.19+1.23+7.57)=79.01
Sl N0 Products mass (kgs) Mol wt Moles Percentage
a b a/b (Molar
Basis)
1 CO2 12.19 44 0.277 8.2
2 CO 1.23 28 0.044 1.3
3 O2 7.57 32 0.237 7.01
4 N2 79.01 28 2.822 83.5
SUM (no of moles of products) 3.38 100
n C3H8+aO2+3.76(a) N2 8.2CO2+1.3CO+7.01O2+83.5N2+dH2O
Carbon balance:
3n=8.2+1.3
n=3.17
Nitrogen Balance:
3.76a =83.5
a=22.21
Oxygen Balance:
2a =2x8.2+2x7.01+ +
44.42=16.4+14.02+ +
d=12.7
Chemical Equation
3.17 C3H8+22.21O2+3.76(22.21)N2 8.2CO2+7.01O2+1.3CO+83.5N2+12.7H2O
Mass of fuel= n C3H8xM C3H8=3.17x44=139.48kg
Air fuel ratio= = =21.85:1
C3H8+aO2+3.76(a) N2 bCO2 +cH2O+3.76(a) N2
Carbon balance ; 3=b
Hydrogen Balance: 8=2c ; c=4
Oxygen Balance: 2a=2b+c
2a=(2x3)+4 ; a=5
Hence equation becomes
C3H8+5O2+3.76(5) N2 3CO2 +4H2O+3.76(5) N2
Mass of fuel= n C3H8xM C3H8=1x44=44
Mass of Air= nO2xMO2+ nN2xMN2=5x32+(3.76x5)x28=686.4
3. 4.4kg Propane gas is burnt completely with 3 kilomoles of air. Find the excess air and molar
analysis of the dry combustion products (July 2004)
Propane gas chemical formula= C3H8
C3H8+aO2+3.76(a) N2 bCO2 +cH2O+3.76(a) N2
Carbon balance ; 3=b
Hydrogen Balance: 8=2c ; c=4
Oxygen Balance: 2a=2b+c
2a=(2x3)+4 ; a=5
Hence equation becomes
C3H8+5O2+3.76(5) N2 3CO2 +4H2O+3.76(5) N2
Mass of fuel= n C3H8xM C3H8=1x44=44
Mass of Air= nO2xMO2+ nN2xMN2=5x32+(3.76x5)x28=686.4
Actual Air fuel ratio
Total mass of Propane =4.4kgs
Mass of actual air supplied = no of moles of air supplied x Mol wt of air
= 3 x 28.97 =86.91
Actual Air fuel ratio= = =21.72:1
Excess Air per kg of fuel= Air supplied – Theoretical air required
=21.72-15.6 =6.12 kg of air per kg of fuel
For 4.4 kg of fuel =6.12x4.4 =24.48 kg of air
Chemical equation with excess air
Mol wt : (12x3)+(1x8)=44
No of moles = = =0.1kmole
0.1 C3H8+3(O2+3.76 N2) aCO2 +bH2O+3.76(3) N2+ c O2
Carbon balance
0.1x3 =a
Hydrogen balance
0.1x8 = 2 b
b=0.4
Oxygen balance
3 x2=2a + +2 c
2x3=2x0.3+ +2c
C=2.5
Nitrogen= 3.76x3 =11.28
0.1 C3H8+3(O2+3.76 N2) 0.3CO2 +0.4H2O+3.76(3) N2+ 2.5 O2
Molar analysis of dry combustion process
Sl N0 Products Moles Percentage

(Molar Basis)
1 CO2 0.3 2.13
2 O2 2.5 17.76
3 N2 11.28 80.11
Sum 14.08 100
Mass analysis of dry combustion process
Sl N0 Products Moles Mol wt mass Percentage

a b axb mass basis
1 CO2 0.3 44 13.2 3.23
2 O2 2.5 32 80 19.56
3 N2 11.28 28 315.84 77.21
Sum 409.04 100
The products of combustion of an unknown hydrocarbon CxHy have the following composition as
measured by an orsat apparatus
CO2=8%, O2=8.8%, CO=0.9% and N2=82.3%.
Determine:
i) the composition of the fuel

ii) The air fuel ratio
iii) The percent of excess air used
Solution:
CxHy+aO2+3.76(a) N2 8CO2+0.9CO+8.8O2+82.3 N2+dH2O
Carbon balance:
x=8+0.9=8.9
Nitrogen Balance:
3.76a =82.3
a=21.89
Oxygen Balance:
2a = 8+0.9 8.8 +
2x21.89= 8+0.9 8.8 +
d=9.28
Hydrogen Balance
y=2d
=2x9.28=18.56
Chemical composition of Fuel
C8.9H18.56
Chemical Equation
C8.9H18.56+21.89O2+3.76(21.89)N2 8CO2+0.9CO+8.8O2+82.3 N2+9.29H2O
Mass of fuel= n fxM f=1(12x8.9+18.56x1)=125.36
Air fuel ratio= = =23.97:1
C8.9H18.56+a O2+3.76 aN2 bCO2 + H2O+3.76a N2
Carbon balance:
8.9=b
Hydrogen balance
18.56 =2c ie c=9.28
Oxygen balance
2a = 2xb+
2a=2x8.9+9.28 ; a=13.54
Hence
C8.9H18.56+13.54 O2+(3.76 x 13.54)N2 8.9CO2 + H2O+(3.76 x 13.54)N2

Mass of fuel= n C3H8xM C3H8=1(12x8.9+18.56x1)=125.36 kgs
Mass of Air= nO2xMO2+ nN2xMN2=13.54x32+(3.76 x13.54 )x28=1858.77kgs
1. Coal with following mass analysis is burnt with 100% excess air. C=74%, H2=4.3%, S=2.7%,
N2=1.5%,H2O=5.5% , O2=5% Ash= 7%. Find moles of gaseous products if 100kg of fuel is burnt
C+O2 CO2
12kg of C burnt with 32kg of O2 to form 44 kg of CO2
C------------O2
12--------- 32
74-----------?
x74=197.33kg of O2 (required to burn 74 kg of C)
12kg of C burnt with 32kg of O2 to form 44 kg of CO2+
12kg of C produces 44kg of CO2
x74=271.33kg of CO2 (74 kg of C produces 273.33kg of CO2)
H2+ O2 H2O
2kg of H2 burnt with 16kg of O2 to form 18 kg of H2O
Hence, 4.3 kg of H2 requires x4.3=34.4kg of O2
2kg of H2 burnt with of O2 to form 18 kg of H2O
Hence 4.3kg of H2 forms x4.3=38.7kg ofH2O
S+O2 SO2+
32kg of S burnt with 32kg of O2 to form 64 kg of SO2
Hence, , 2.7kg of S requires x2.7=2.7kg of O2
32kg of S burnt with O2 to form 64 kg of SO2

Hence,2.7kg of S produces x2.7=5.4kg of SO2
Hence O2 required =197.33(for C)+34.4(for H2)+ 2.7(for S) – 5(O2 present in the 100kg of
fuel)=229.43kg of O2
But 100% of excess air is supplied, Hence O2 is supplied (1+1) x 229.43=458.86kg of O2
In air every 1kg of O2 there is kg of N2
Hence Air supplied consists of x458.86=1536.18 kg of N2
For 100kg of Fuel

(Molar
Basis)
1 CO2 271.33 44 6.17 8.70
2 H2O 38.7+5.5(fuel)=44.2 18 2.46 3.47
3 SO2 5.7 32 0.178 0.25
4 N2 1536.18(supplied 28 54.91 77.46
Air)+1.5(fuel)=1537.68
5 O2 458.86(Supplied)- 32 7.17 10.11
229.43(required)=229.43
2. A sample of fuel has the following percentage composition by weight: Carbon 84%; Oxygen
=3.5%; Hydrogen=10%; Ash=1%; Nitrogen =1.5%
Determine the stoichiometric Air fuel ratio by mass
If 20% excess air is supplied, find the percentage composition of dry flue gases by volume(July2007)
Solution
Oxygen required for complete combustion of fuel
H2+ O2 H2O
Hence, 0.10 kg of H2 requires x 0.10=0.8 kg of O2
C+O2 CO2
0.84 kg of Carbon require x0.84 =2.24 kg of Oxygen
Hence total Oxygen required for complete combustion of 0.84 kg of C and 0.10 kg of H2
=2.24+0.8=3.04 kg of O2
Since fuel contains 0.035 kg of O2 Oxygen to be supplied through air = 3.04-0.035=3.005kg of

Oxygen
Hence air required x 3.005=13.065kg of air required per kg of fuel
Hence theoretical air fuel ratio required is 13.065:1
ii) If 20% excess air is supplied dry flue gases analysis
C+O2 CO2
0.84 kg of C produces x0.84 =3.08kgs of CO2
Air supplied is 20 percent excess Hence, mass of air supplied is =13.065x1.2=15.678kgs
mass of N2 present in 17.484 kgs of air = x 15.678=12.072kg
mass of O2 present in the product due to excess supply of air
= x (15.678)-3.005(required for combustion)=0.6009kgs
Dry analysis of the products

a b a/b (Molar Basis)
1 CO2 3.08 44 0.07 13.47
2 N2 12.072 28 0.4311 82.94
4 O2 0.6009 32 0.0187 3.597
A hydrocarbon fuel C12H26 is burnt with 50% excess air. Determine the volumetric (Molal ) analysis of
the products of combustion and also the dew point temperature of the products if pressure is
101kpa
Stoichiometric chemical equation
C12H26 +18.5O2+3.76(18.5) N2 12CO2 +13H2O+3.76(18.5) N2
With 50% excess air
C12H26 +1.5[18.5O2+3.76(18.5) N2] 12CO2 +13H2O+0.5(18.5)O2+1.5[3.76(18.5)] N2
Sl N0 Products Moles Percentage

(Molar Basis)
1 CO2 12 9.555
2 O2 9.25 7.365
3 N2 104.34 83.079
Sum 125.59 100
No of moles of water =13
Molal fraction of H2O= = =0.1035

Hence partial pressure of H2O= Molal fraction x total pressure =1.01x0.1035 =0.10455 bar
Dew point temperature of products is the saturation temperature of water at 0.10455 bar ie
The fuel used in petrol engine contains 87% Carbon and 13% H2. The air supply is 75% of that
theoretically required for complete combustion. Assuming H2 is burned and there is no free carbon
left, find the volumetric analysis of dry exhaust gases (Dec07/Jan08)
Oxygen required for complete combustion of fuel
The fuel used in petrol engine contains 87% Carbon and 13% H2.
O2 required for combustion of H2 present in 1 kg of fuel
H2+ O2 H2O
Hence, 0.13 kg of H2 requires x 0.13=1.04 kg of O2
O2 required for combustion of C present in 1 kg of fuel
C+O2 CO2
0.87 kg of Carbon require x0.87 =2.32 kg of Oxygen
Hence total Oxygen required for complete combustion of 0.87 kg of C and 0.13 kg of H2
=2.32+1.04=3.36 kg of O2
But actual air supplied is 75% of theoretical air, hence oxygen supplied = 0.75x3.36=2.52 kg of
Oxygen
According to data H2 completely burns. Hence, Oxygen available for combustion of C is

2.52-1.04=1.48kg less than required for complete combustion
Hence carbon due to incomplete combustion produces CO and CO2
Let x kg of C produces CO and y kgs of C produces CO2

Also carbon in 1 kg of fuel =0.87 (Data)
Hence x +y =0.87-----------------1
Oxygen required for combustion of x kgs of carbon to CO
C+ O2 CO
12kg of C burns with 16 kg of O2 to form 28kg of CO
Hence O2 required for combustion of x kgs of C to form CO = x
Oxygen required for combustion of y kgs of carbon to CO2
C+ O2 CO2
Hence O2 required for combustion of y kgs of C to form CO2 = y
Hence, Oxygen Utilised for combustion of C to CO and CO2
x + y
Utilised =available
x + y =1.48----------------2
x+y =0.87---------------1
hence y=0.87 X
x + (0.87 X) =1.48
X + (0.87 X) =1.48
X=0.63
Hence 0.63+y =0.87
Y=0.24
Product analysis
C+ O2 CO
And x=0.63 kgs of C produces= x0.63 =1.47 kg of CO

C+ O2 CO2
And y =0.24 kg of C produces ( 0.24)=0.88kgs of CO2
O2 is supplied through air
1kg of air consists of 77kg of N2 and 23 kg of O2 and N2 will remain as it is in the product
O2 N2
23 77
2.52 ?
Hence 2.52 kg of O2 supplies ( 2.52)=8.43 kg of N2 remains as it is in the product
Hence the dry product consists of CO, CO2 and N2
Note that since analysis is dry analysis H2O in the product should not to be considered

a b a/b (Molar
Basis)
1 CO2 0.88 44 0.02 5.35
2 CO 1.47 28 0.0525 14.04
4 N2 8.44 28 0.3014 80.61
A sample of fuel has the following percentage composition: Carbon=86%, Hydrogen =8%,
Sulphur=3%, Oxygen =2% Ash=1%
For an air fuel ratio of 12:1 calculate
i) Mixture strength as a percentage of rich or weak
ii) Volumetric analysis of the dry product of combustion Dec06/Jan07
Solution
C+O2 CO2
0.86 kg of Carbon requires x0.86 =2.293 kg of Oxygen
0.86 kg of C produces x0.86 =3.153 kgs of CO2
H2+ O2 H2O
0.08 kg of H2 requires x 0.08=0.64 kg of O2
0.08 kg of H2 produces x0.08=0.72kgs of H2O
S+O2 SO2
Hence, 0.03kg of S requires x0.03=0.03kg of O2
0.03kg of S produces x0.03=0.06kg of O2
Total Oxygen require for complete combustion of fuel =2.293+0.64+0.03-0.02(Fuel)=2.943kgs
Air required for complete combustion = x 2.943=12.79(Theoretical)
But supplied is 12:1 It implies that air supplied is less than theoretical Hence supplied air fuel
ratio is rich
Mixture strength =
Mixture strength as a percentage of rich = =106.58
Oxygen supplied = x12 =2.76kg of oxygen

Generally H2 completely burns. Hence, Oxygen available for combustion of C is 2.76-0.64=2.12kg
less than required for complete combustion
Hence carbon due to incomplete combustion produces CO and CO2
Let x kg of C produces CO and y kgs of C produces CO2
Oxygen required for combustion of x kgs of carbon to CO
C+ O2 CO
Hence O2 required for combustion of x kgs of C = x
And x kgs of C produces= x of CO
Oxygen required for combustion of y kgs of carbon to CO2
C+ O2 CO2
Hence O2 required for combustion of y kgs of C = y
And x kgs of C produces= y of CO
Hence, x + y =2.12
Also x+y =0.86
Solving above two equations x=0.1260 kg and y=0.7339
Products
CO = x = (0.1260)= 0.294kgs of CO
CO2= y= ( 0.7339) =2.69kgs of CO2
N2 supplied from air = x12=9.24kg of N2
Note that since analysis is dry analysis H2O in the product should not to be considered

a b a/b (Molar
Basis)
1 CO2 2.69 44 0.0611 15.21
2 CO 0.294 28 0.0105 2.614
4 N2 9.24 28 0.33 82.17
1. What are the performance parameters used in IC engine testing
Engine performance is an indication of the degree of success with which it does its assigned job
i.e. conversion of chemical energy contained in the fuel into the useful mechanical work.
1. Mean effective pressure and torque

2. Power and mechanical efficiency
3. Specific output
4. Volumetric efficiency, Relative efficiency and air standard efficiency
5. Fuel-Air ratio
6. Brake Specific fuel consumption
7. Thermal efficiency
8. Heat balance sheet
9. Emissions from engines
2.List the formulae used in IC engine testing
( ) ( ) ( ) ( )
IP= , A= , d= diameter of bore in m, L=stroke length in m
or kPa
Theoretically n=
If no of explosion per minute is given in the problem then n= no of explosion per minute( ie we should
not use n= )
k=number of cylinder
BP= in terms of mean effective

pressure
( )( )
T=
( )
BP: if T is in Nm (BP in terms of Torque
BP: if T is in kNm
N=speed in rpm for all cases
If N is given in rps then there is no 60 in the denominator of above formula Note down that 60 is used to
convert minute to sec
Friction Power =
Note: Friction Power is equal to the motor Power if the Engine is run by the motor without
combustion of fuel
Indicated thermal efficiency= and C.V is in calorific value of fuel in kJ/kg
Brake thermal efficiency=
Relative efficiency=
Vthe= ( ) for 4 stroke
In the above formula is used because no of suction strokes per minute in 4 stroke engine is since
one thermodynamic cycle is completed in 2 revolutions
Vthe= for 2 stroke
In the above formula only is used because no of suction strokes per minute in 4 stroke engine is since
one thermodynamic cycle is completed in 1 revolution
Heat Balance sheet:
1. Heat input : mf X CV kW
2. BP = in kW
3. Heat carried by cooling water: mw Cpw (Tco – Tci) kW where mw in kg/s,

Cpw =4.187kJ/kgK specific heat of water, Tco =temperature of outlet water in oC ,
Tci = temperature of inlet water in oC, (Tco – Tci)=raise in temperature of cooling water
in K or oC
4. Heat carried by exhaust gases : (mf + ma ) Cpg (Tex – TRoom) or

: mf ((ma/mf)+1) Cpg (Tex – Troom)
Tex is exhaust temperature and Troom= Room temperature
Where mf is mass of fuel in kg/s, ma mass of air kg/s ma/mf = air fuel ratio,
Cpg=specific heat of gas in kJ/kgK If it is not given in the problem take as specific heat of air
=1.005kJ/kgK
5. Heat un account for : 1 – (2+3+4)
3. What are the measurement methods for Indicated power, explain them
1.Indicator
An indicator is fixed on the top of head which has a compression spring vibrates according to variation of
pressure inside the cylinder, the same is recorded by a stylus on a paper attached to a rotating drum so
that for each cycle a P-V diagram as shown above is obtained. The area of the diagram is measured by a
planimeter in laboratory. The Mean effective pressure is calculated using the following formula.
where
= Indicated mean effective pressure in kPa,
a = Area of indicator diagram, m2,
l = Length of indicator diagram in, m,
s=spring constant in mm/mm/Kpa.
2. Williams line method:

This method is only used for Diesel engine, as in petrol engine a mixture of petrol and air enters into
cylinder where as in diesel engine only diesel is injected into cylinder. The graph of fuel consumption
versus Brake power is drawn, A tangential line to this line is extrapolated back to meet x axis on the back
side which gives the friction power as shown in figure. Then the IP is calculated from the formula. The
speed is maintained constant throughout the experiment so as to have the constant friction power.
3.Motoring test:
In this test the engine is first run up to the desired speed by its own power and allowed to remain under
the given speed and load conditions for some time so that oil, water and engine component
temperature reach stable conditions. The power of the engine during this period is absorbed by a
dynamometer. The fuel supply is then cut-off and by suitable electric switching devices the
dynamometer is converted to run as motor to drive or ‘motor’ the engine at the same speed at which it
was previously running. The power supply to the motor is measured which is a measure of F.P. of the
engine.
FP=power supplied by electric motor.
4.Morse test
This method is used for finding of IP in multi cylinder engines
This test is applicable only to multi-cylinder engines. The engine is run at the required speed and the
torque is measured. One cylinder is cut-off by shorting the plug if an S.I. engine is under test, or by
disconnecting an injector if a C.I. engine is under test. The speed falls because of the loss of power with
one cylinder cut-off, but is restored by reducing the load. The torque is measured again when the speed
has reached its original value.
For a 4 cylinder engine IP is calculated as follows

4. What are the measurement methods for Brake power, explain them
1. Rope brake dynamometer
In rope brake dynamometer a rope is wound round the circumference of the brake wheel. To one end
of the rope is attached a spring balance (S) and the other end carries the load (W). The speed of the
engine is noted from the tachometer.
Let W = Weight at the end of the rope, in N,
S = Spring balance reading, in N,
If W or S is given in kgs convert into Newton by multiplying kgs by 9.81
N=kgsx9.81
N = Engine speed, in r.p.m.,
Db = Diameter of the brake wheel, in m,
dr = diameter of the rope, in m, and
(Db + dr) = Effective diameter of the brake wheel,
( )( )
T=
BP: where T is in Nm
Note down that in the above formula in the denominator 1000 is used to convert Nm to KNm and 60 is
used to convert min to sec
BP: if Torque is in KNm
2. Pony brake dynamometer
This arrangement consists of a pair of brake shoes (usually made of wood) which are held in place by
means of spring loaded bolts. The pressure on the rim of the brake drum (wheel) is adjusted with the
help of the nuts.Weights are placed on the load carrier at the end of the load bar (lever). Increasing the
weights will increase the pressure of the brake shoes on the drum, which results in an increase in the
frictional torque that the engine has to overcome.
T= where note that if W is given in kgs convert into Newton
ie Newton =9.81xkgs
BP:
Note down that in the above formula in the denominator 1000 is to convert Nm to KNm and 60 is used
to convert min to sec
5. Write a note measurement of fuel consumption

The mass rate of fuel consumption is measured by noting the time taken for the consumption of a
known volume of fuel. If V cc of fuel is consumed in ‘t’ seconds, then mass rate of fuel consumption is
6. Write a note on air consumption measurement in IC engine

The air supplied to engine is measured by air box method, in the set up an empty box of capacity 500
times the engine capacity is fitted to engine suction on one side and open to atmosphere through an
orifice on opposite side. A U-tube water manometer is connected and as engine is started air flows
through the box to the engine and the reading of manometer is recorded. The volume flow rate of air is
calculated by the following formula
Where A is area of orifice, Cd=0.62, hw=reading in manometer.
7. Write a note on characteristic curves in IC engines
From figure maximum efficiency, maximum power and minimum fuel consumption can be obtained if
we run the engine between 2000 and 3000 rpm hence it is always better to run the engine in the speed
range of 40 to 60KMPH to get optimum performance.
NUMERICALS :
1. A 4 cylinder engine has the following data: Bore=15 cm; Stroke=15cm; Piston speed
=510m/min; B.P= 60kW; ηmech=0.80; pm=5 bar; C.V=40000kJ/kg. Calculate i) Whether
this is 2 Stroke or 4 Stroke engine?
Solution
( )
ηmech= ; ; ;
IP=
( ) ( )
( ) ;
Piston Speed(m/min ) ; ; N=1700
if engine is 4 stroke and if then engine is 2 stroke
Ie
Hence engine is 4 stroke
2. A 4 cylinder has a following data Bore=15cm; Piston speed =510m/min; B.P.=60kW;
ηmech=0.80; pm=5 bar; C.V=40000kJ/kg. Calculate i) Whether this is 2 Stroke or 4 Stroke
engine?
3. Following data is available for a S.I engine, single cylinder, 4 stroke, air fuel ratio 16:1
CV=45000kJ/kg, ηmech=0.80; air standard efficiency = 0.5; relative efficiency =0.7;
Stroke Bore ratio=1.5; Suction conditions; 1 bar and 30oC, speed =2500 rpm, B.P=75kW;
Calculate the compression ratio, indicated thermal efficiency, brake specific fuel
consumption(BSFC); brake R
; ; ;
ηmech=
( )
; ;
4 Stroke engine (theoretical) since number of explosions is not given
explosions per minute
( )
( )
( ) ( )
( )
( ) ( )
( );
( )=21.4285kg/hr
( )
= =
( )
=
( ) ( )
In 4 Stroke engine in every 2 revolution there will be 1 suction stroke.
In 2 Stroke engine in every 1 revolution there will be 1 suction stroke.
Hence swept volume per sec where for 4 Stroke
Actual volume sucked :
( ) ( )
( )
( ) ( )
( )
4. The following data were recorded during a test on a single cyinder four stroke oil engine
Bore=150mm, Stroke =300mm, speed =18000 revolutions per hour, Brake torque=200N-m,
indicated mean effective pressure =7bar, fuel consumption = 2.04kg/hr, cooling water flow rate
=5kg/ min cooling water temperature rise = 30oC, Air-fuel ratio=22, exhaust gas temperature
=410oC, Specific heat of exhaust gases = 1.0kJ/kgK, room temperature is 20oC, calorific value of
fuel=42MJ/k, Determine i) Mechanical efficiency ii) BSFC and draw the heat balance sheet on
minute basis and percent basis(june/July08)
Solution
Data:
Number of cylinder =1
Number of stroke =4
Bore=150mm, ie D=0.15m; Stroke =300mm ie L=0.3m
speed =18000 revolutions per hour, N=18000 rev/hr=
Brake torque=200N-m ie T=200N-m, ;
Indicated mean effective pressure =7bar ie
fuel consumption = 2.04kg/hr ie
cooling water flow rate =5kg/ min 5kg/ min
cooling water temperature rise = 30 C ie Tco – Tci=30oC
o
Air-fuel ratio=22 ie AF=22, exhaust gas temperature =410oC ie Tex = 410oC,

Specific heat of exhaust gases = 1.0kJ/kgK,
room temperature is 20oC ie TR,= 20oC ;
calorific value of fuel=42MJ/kg ie C.V=42000kJ/kg
( )
BP: = =6.28 kW.
IP= , A= =0.0177m2 k, number of cylinder
n= for 4 stroke ie n= =100
( )
IP= = 6.195 kW
= = 98.6%
Heat Balance sheet:
1. Heat input:
mf =2.04kg/hr = 2.04/60 kg/min
Q= mf X CV = (2.04/60) X 42000
=1428 kJ/Min
2. BP = 6.28 kW X60 =376.8 kJ/Min

3. Heat carried by cooling water: mw Cpw (Tco – Tci) =5X4.187x30=628.05 kJ/Min
4. Heat carried by exhaust gases : (mf + ma ) Cpg (Tex – TR)
: mf ((ma/mf)+1) Cpg (Tex – TR)
=(2.04/60)X(22+1) x1x(410-30)
=297.16 kJ/min

: 1428 – (376.8 + 628.05 + 297.16)
: 125.99 kJ/min
Energy input, kJ/min % Energy consumed, kJ/min %

1428 100 2. Energy consumed as 26.39
1. Heat input brake power 376.8
3. Energy carried by 628.05 43.98

coolant
exhaust gases
5. Unaccounted losses 125.99 8.82
1428 100 Total 1428 100

Total
5. A test on a 2 stroke oil engine gave the following results at full load: Speed = 350rpm,
Net brake load = 650N, imep = 3bar, fuel consumption = 4kg/hr, Jacket cooling water
flow rate = 500kg/h, Jacket water temperature at outlet = 40o C , Jacket water temperature
at outlet = 20o C , exhaust temperature = 400o C. Air used per kg fuel = 32kg, cylinder
diameter = 22cm, stroke = 28cm, Brake drum circumference = 314cm, calorific value of
the fuel = 43MJ/kg, Mean specific heat of exhaust gases 1kJ/kgK. Room Temperature
=20o C Determine (i) Mechanical efficiency, (ii) BMEP, Draw energy balance sheet in
kW and in percentage. (July06)
Data:
N=350RPM; Brake Net brake load = 650N,ie W =650N; pm=3bar= 300kPamf=4kg/hr= ;

500 kg/hr= kg/s; cooling water temperature rise = 30o C ie Tco =40o C Tci=20o C; ;
Air used per kg fuel = 32kg ie AF=22; ; stroke = 28cm ie L=28cm =0.28m;
Circumference=314cm ie πD=314cm, CV=43 ; 20o C
Circumference=πD, There fore D=3.14/3.14 = 1 m
( )( ) ( )( )
T= = = 325 N-m
( )
BP: = =11.9 kW.
IP= xk, where
A= =0.038m2
N=n for 2stroke
( )
IP= = 18.62kW
= = 0.639=63.9%
BP= , A= =0.038m2
= =1.92X102 kN/m2
Heat Balance sheet:
1. Heat input :
mf= 4kg/hr = 4/3600 kg/s
Q= mf X CV =(4/3600) X 43000
=47.78 kW
2. BP = 11.9 kW
3. Heat carried by cooling water: mw Cp (Tco – Tci)
=(500/3600)X4.187x(40-20)
=11.6kW
Air fuel ratio = ma/mf=32
:(4/3600)X(32+1) x1x(400-20)
: 13.93kW
: 47.78 – (11.9 + 11.6 + 13.93)
: 10.35 Kw
Energy input, kW % Energy consumed, kW %

2. Energy consumed as
47.78 100 brake power 24.9
1. Heat input 11.9
3. Energy carried by
11.6 24.28
coolant
13.93 29.15
exhaust gases
47.78 100 Total 47.78 100

Total
Note:
In this problem note down circumference of Brake wheel is given
Hence diameter of the brake wheel should be found out by formula Circumference=πD
6. In a test on a three cylinder four stroke internal combustion engine with 22 cm bore and
26cm stroke the following were the observations during a trial periods of one hour: Fuel
consumption = 8.0kg. Calorific value = 45000kJ/kg, total revolutions of the crank shaft
12000, mean effective pressure = 6 bar, net load on brake= 1.5kN, brake drum dia=1.8m,
rope dia = 3cm, mass of cooling water =550kg, inlet temperature of water = 27oC, exit
temperature of water = 55oC air consumed = 300kg, ambient temperature = 30o C,
exhaust gas temperature =310o C, specific heat of gases 1.1kJ/kgK, Calculate (i)
indicated and brake power, (ii) Mechanical efficiency (iii) indicated thermal efficiency.
Also draw a heat balance in kJ/min (july/Aug 2004)
Data:
Single cylinder ie k=1
Stroke 4
22 cm bore and 26cm stroke D=0.22m; L=0.26m
trial periods of one hour: Fuel consumption = 8.0kg.
ie kg/s= kg/min
Calorific value = 45000kJ/kg CV=45000kJ/kg
total revolutions of the crank shaft 12000,ie N=12000 in one hr trial period
N= =2000rpm
mean effective pressure = 6 bar ,
net load on brake= 1.5kN, ie W
brake drum dia=1.8m ie ; rope dia = 3cm ie
mass of cooling water =550kg, mass of cooling water in trial period of one hr
ie kg/s= kg/min
inlet temperature of water = 27oCie 27oC;

exit temperature of water = 55oC ie 55oC ;
air consumed = 300kg in one hr trial period
ie kg/s= kg/min,
ambient temperature = 30 C ie =30o C,
o
exhaust gas temperature =310o Cie 310o C,

specific heat of gases 1.1kJ/kgK, Cpg=1.1kJ/kgK
( )( ) ( )( )
T= = = 1372.5 N-m
total revolutions of the crank shaft 12000 in one hour trial there for N = rpm
( )
BP: = =28.73 kW.
IP= where k is the number of cylinders
n= for 4 stroke ie
A= =0.037994m2
IP= = 29.64 kW
= = 96.92%
mf=8kg in one hour trial; hence mf= = kg/s = kg/min
Indicated thermal efficiency= = = 0.2964 or 29.64 %

( )
Heat Balance sheet:
1. Heat input : mf X CV =(8/60) X 45000
=6000 kJ/Min
2. BP = 28.73 X60 =1723.8 kJ/Min

3. Heat carried by cooling water:
mw =550kg in one hr trial =550/60 kg/min
Qw= mw Cp (Tco – Tci)
=(550/60)X4.187x(55-27)
=1074.66kJ/Min
Air consumed =300kg in 1 hr trial ie ma=300kg/hr = kg/min
=( ) ( )
=1581. 07kJ/min

: 6000 – (1723.8 + 1074.66 + 1581.07)
: 1620.47 kJ/min
Energy input, kJ/min % Energy consumed, kJ/min %

6000 100 2. Energy consumed as 28.73
1. Heat input brake power 1723.8

coolant
exhaust gases
6000 100 Total 6000 100

Total
7. A test on a single cylinder, four stroke oil engine having a bore of 15cm and stroke 30cm
gave the following results: speed = 300RPM, Brake torque =200Nm, indicated mean
effective pressure = 7 bar, fuel consumption = 2.4kg/h, Cooling water flow rate=4.5
kg/Min,cooling water temperature rise = 30o C, Air fuel ratio = 22. Specific heat of
exhaust gases=1.0kJ/kgK Exhaust gas temperature = 410oC, Room temperature= 20oC,
Room pressure= 1bar, calorific value of the fuel=42MJ/kg, R=.2872kJ/kgK of air.
Determine 9i) the indicated thermal efficiency (ii) Volumetric efficiency base on
atmospheric conditions (iii) Draw an energy balance sheet in terms of kJ/min and on
percent basis. (Jan/Feb 06)
Data: D=15cm=0.15m; L=30cm=0.3m; N=300RPM; Brake Torque= 200Nm ie T=200Nm; p m=7bar= 700kPa
mf=2.4kg/hr= ; 4.5 kg/Min ;cooling water temperature rise = 30o C ie Tco – Tci=30o C;
AF=22; ; ; ; CV=42 R=0.287kJ/kgK
IP= , where pm=is in kN/m2
A= =0.0177m2
n= since engine ie 4 stroke
( )
IP= = 9.29 kW
Vact= mass of air/ Density of air
Mass of air= Fuel consumption X Air fuel ratio

Mf =2.4kg/hr = kg/s
Mass of air=(2.4/3600)X22 =0.015 kg/s
=1.189 kg/m3
m =ρV hence V=
Vact=0.015/1.189=0.0126 m3/s
Vthe= ( ) Here is used since engine is 4 stroke
note that suction stroke is for 4 stroke engine and number of suction stroke =N for 2 stroke engine
Vthe = ( ) =0.0132 m3/s
=0.9545
Heat Balance sheet:
1. Heat input : mf X CV =(2.4/3600) X 42000
=28 kWX60=1680 Kj/Min
( )
2. BP: = =6.28 kWX60=376.8Kj/Min
3. Heat carried by cooling water:
mw=4.5kg/hr=4.5/60kg/min
Qw= mw Cp (Tco – Tci)
=(4.5/60)X4.187x(30)
=9.42kWX60=565.24Kj/Min
:(2.4/3600)X(22+1) x1x(410-20)
:5.98 kWX60=358.8Kj/Min
: 1680 – (376.8 + 565.24 + 358.8)
: 379.16 Kj/Min
Energy input, Kj/Min % Energy consumed, Kj/Min %

1680 100 brake power 22.42
1. Heat input 376.8
565.24 33.65
coolant
358.8 21.32
exhaust gases
1680 100 Total 1680 100

Total
7. The following observations were made during a trial of a single cylinder four stroke cycle
gas engine having cylinder diameter of 18cm and a stroke of 24cm: Duration of Trial=
30min; Total number of revolutions = 9000, total number of explosions = 4450, Indicated
mean effective pressure = 5 bar. Net load on the brake wheel = 390N. Effective diameter
of brake wheel = 1m, calorific value of gaseous fuel at NTP= 19MJ/m3, Total fuel used at
NTP= 2.4m3, total air is used = 36m3, pressure of air = 720mm of Hg, density of air =
1.29kg/m3, temperature of air =17oC, temperature of exhaust gases =4100C,specific heat
of exhaust gases: 1.0kJ/kgK. Room temperature =17oC, cooling water circulated = 80kg,
Rise in water temperature =30oC. Draw up a heat balance sheet and estimate the
mechanical and indicated thermal efficiencies of the engine. Take R= 287J/kgK
(June/july08) (july/Aug 05).
Data
Number of cylinder k=1
Number of stroke=4
D=0.18m; L=0.24m
Duration of trial 30min Total number of revolutions = 9000 ie N=9000 in 30min
N= rpm, total number of explosions = 4450 ie n=4450 in 30 min n= per minute,
Indicated mean effective pressure = 5 bar ie ;.
Net load on the brake wheel = 390N.ie
Effective diameter of brake wheel = 1m ie Db=1m,
calorific value of gaseous fuel at NTP= 19MJ/m3, CV(at NTP) =19MJ/m3
Total fuel used at NTP= 2.4m3, ie Vf=2.4 m3 in 30 min at NTP
Ie Vf= m3/min(at NTP)= m3/min(at NTP)
total air is used = 36m3, ie 36m3 in 30min m3/min= m3/sec
(at pressure of air = 720mm of Hg, density of air = 1.29kg/m3, temperature of air =17oC,)
temperature of exhaust gases =4100C,ie 4100C
specific heat of exhaust gases: 1.0kJ/kgK. Ie
Room temperature =17oC, Ie 17oC
cooling water circulated = 80kg,ie =80kg in 30min = kg/min
o o
Rise in water temperature =30 C ie (Tco – Tci)= 30 C
( )( ) ( )( )
T= = = 195 N-m
N= rpm Note down given is total number of revolutions in 30min trial period
( )
BP: = =6.123 kW.
IP= , A= =0.025434m2
Here n is not equal to since no of explosions (actual working stroke) is given
Total number of explosion is 4450 in 30min Hence n=
( )
IP= x1= 7.55 kW
= = 81.1%
Vf=2.4 m3 at NTP in 30min trial
Vf = m3/min= m3/sec at NTP
CV =19000kJ/m3 at NTP

( ) ( ) ( )
Heat Balance sheet:
1. Heat input : mf x CV
Volume of fuel used is 2.4 m3 in 30 min
Hence m3/s at NTP
Calorific value CV is 19000kJ / m3 at NTP
Q = Vf at NTP x CV at NTP
Q =(2.4/(30X60)) X 19000
=25.33 kW
2. BP = 6.123 kW
=(80/(30X60))X4.187x(30)
=5.58kW
4. Heat carried by exhaust gases : (mf + ma ) Cpg (Tgo – Tgi)
Atmospheric Pressure head at room is 720mm of Hg
Conversion of mm of Hg to bar
760mm Hg is equivalent to bar

Hence 720mm of Hg = =97.06kPa
Mass of air = Volume of air at room temperature x density at room temperature
(m3/s) kg/ m3 (both quantity at room temperature)
( )
Note If density of air is not given use ( )
Mass of fuel
Since density of fuel is not given assume density of fuel = density of air
( ) ( )
Density of air =1.29kg/m3 at room temperature (given)
Hence take ( )
Hence volume of fuel used /sec is to be converted into volume fuel at room temperature using Ideal gas
equation
( ) ( )
o
NTP pressure and temperature are 1.01325bar and 0 C or 273K
( ) ( )
VfRTP: 1.494 m3/s
( ) ( )
1.494
Heat carried by exhaust gases : (mf + ma ) Cpg (Tgo – Tgi)
( )1(410 – 17)=10.66kW

: 25.33 – (6.123 + 5.58 + 10.66)
: 2.967 kW
1. Heat input 25.33 100 brake power 6.123 24.17
5.58 22.03
coolant
10.66
exhaust gases
5. Unaccounted losses 2.967
25.33 100 Total 25.33 100

Total
8. 5. A gas engine working on constant volume cycle gave the following results during a one
hour test run. Cylinder diameter 24cm, stroke 48cm. effective diameter of brake drum wheel
1.25m, Net load on the brake 1236N, average speed 226.7revolutions per minute. Average
explosions per minute 77. MEP 7.5 bar, gas used 13m3 at 15oC and 771mm of Hg pressure.
Lower calorific value of gas 22000kJ/m3 at NTP. Cooling water used 625kg, inlet water
temperature 25oC. Outlet water temperature 60oC. Determine i) Mechanical efficiency (ii) the
specific fuel consumption in m3/IP hr. (iii) Indicated and brake thermal efficiencies. Draw
heat balance for the engine on minute bases NTP conditions are 760mm of Hg and 0 oC (Dec
06/Jan07)
Data: one hr test run
D=24cm=0.24m; L=48cm=0.48m; N=300RPM;
effective diameter of brake drum wheel 1.25m ie
Brake Net load on the brake 1236N =1236N;
average speed 226.7revolutions per minute.ie N=226.7 rpm;
Average explosions per minute 77 ie n=77 per min; MEP 7.5 bar ie pm=7.5bar=7.5 ;
gas used 13m3 at 15oC and 771mm of Hg pressure (duration one hour)
ie at pressure 771mm of Hg and temperature 15oC
Lower calorific value of gas 22000kJ/m3 at NTP. CV = at NTP ie 1.0325 bar and 0o C
Cooling water used 625kg ( duration of trial = 1hr) ie = kg/min
Inlet water temperature 25oC ie Tci=25o C; Outlet water temperature 25oC ie Tci=60o C
Solution
( )( ) ( )( )
T= = = 772.5 N-m
( )
BP: = =18.32 kW
IP= xk
Here n is not equal to since number of explosion in the problem is given
n=Average explosions per minute 77 ie n=77 /min
A= =0.045m2
( )
IP= = 20.79 kW
= = 88.1%
Sfc=
Sfc=13/20.79=0.625 m3/IP hr (based on IP)
Pressure of fuel supplied =771mm of Hg
P= ωmercury x gxhmercury
Conversion of mm of mercury into pressure N/m2
P =(1000X13.6)x9.81x (771/1000)=102.86 x103 N/m2 =102.86kN/m2
OR
1.013 bar = 760mm of Hg
? in bar = 771mm of Hg
Pressure of fuel supplied in bar = x 771mm of Hg =1.02766 bar =102.76 kN/m2
Conversion of volumetric fuel flow at supply pressure to pressure of fuel at NTP
Normal pressure =1.01325 bar =101.325kN/m2 and Normal temperature = 273K
Temperature of fuel =15oC

( ) ( )
( ) ( )
VNTP of fuel = 12.5 m3 in 1 hr trial
VNTP of fuel = m3/sec
Q= ( ) ( ) =( ) kJ/s

( )
Brake thermal efficiency= = = 0.239 or 23.9 %

( )
Heat Balance sheet:
1. Heat input : =(12.5/(60)) X 22000
=4583.33 Kj/min
2. BP = 18.32 kWX60=1099.2 Kj/min

=(625/(60)X4.187x(60-25)
=1526.5 Kj/min
4. Heat carried by exhaust gases : no data reg air consumption=0
: 4583.33 – (1099.2 + 1526.5 + 0)
: 1957.63Kj/min
Energy input, Kj/min % Energy consumed, Kj/min %
1. Heat input 4583.33 100 brake power 1099.2 23.98
1526.5 34.09
coolant
0 0
exhaust gases
4583.33 100 Total 4583.33 100

Total
9. The following data were obtained from a Morse test on a 4 cylinder, 4 stroke cycle SI
engine, coupled to hydraulic dynamometer operating at a constant speed of 1500rpm:
Brake load with all cylinders firing = 296N, Brake load with cylinder No 1 not firing =
201N, Brake load with cylinder No 2 not firing = 206N, Brake load with cylinder No 3
not firing = 192N, Brake load with cylinder No 4 not firing = 200N. The brake power in
kW is calculated using the equation BP= WN/42300, where W is the brake load in
Newtons and N is the speed of the engine in RPM, Calculate : i) Brake power ii)
Indicated power iii) Friction power, iv) Mechanical efficiency(Dec2011).
N=1500rpm;
=296N; =201N; =206N; =192N; =200N
BP1,2,3,4= N/42300
BP1,2,3,4= (296X1500)/42300 =10.5kw
BP,2,3,4= N/42300
BP234= (201X1500)/42300 =7.13kw
BP1, ,3,4= N/42300
BP134= (206X1500)/42300 =7.3kw
BP1,2, ,4= N/42300
BP124= (192X1500)/42300 =6.8kw
BP1,2,3, = N/42300
BP123= (200X1500)/42300 =7.09kw
(ip)total =ip1 +ip2 +ip3 +ip4 = (BPt – BP234)+(BPt – BP134)+(BPt – BP124)+(BPt – BP123)
=4Bt –(B1 +B2 +B3 +B4)=4 x10.5 – (7.13 +7.3 +6.8+7.09)
=13.68 Kw
FP=IP-BP=13.68-10.5=3.18Kw
6.
7.In a test of 4- cylinder, 4- stroke petrol engine of 75mm bore and 100mm stroke, the following results
were obtained at full throttle at a constant speed and with a fixed setting of the fuel supply at
0.082kg/min. BP with all the 4 cylinders working = 15.24kW, BP with cylinder No 1 is cut off = 10.45kW,
BP with cylinder No 2 is cut off = 10.38kW, BP with cylinder No 3 is cut off = 10.23kW, BP with cylinder
No 4 is cut off = 10.45kW. Determine the (i) the indicated power, (ii) the indicated thermal efficiency if
the calorific value of the fuel = 44MJ/kg, (iii) Relative efficiency based on IP if clearance volume in each
cylinder = 115cc (July06)
=4Bt –(B1 +B2 +B3 +B4)=4 x15.24 – (10.45 +10.38 +10.23+10.45)
=20.29 Kw
mf =0.082kg/min =

( )
Vs= = =441.56 cm3 per stroke
=4.84
=0.468
Relative efficiency= =0.72 or 72%
10.The following readings were recorded during a trial on a single cylinder, 2 stroke diesel engine. Power
supplied by electric motor= 1.5kW. Rated speed= 500 rpm , Net loads on brake =225N. Diameter of the
brake wheel = 100cm. Rate of flow of cooling water through engine jacket = 13.65kg/min, Rise in
temperature of cooling water = 10oC, Fuel consumption= 2kg/hr. calorific value of fuel used =
43000kJ/kg; AF ratio = 32:1, Cp (gases) = 1.006kJ/kgK Exhaust gas temperature = 345oC, Ambient
temperature = 25oC and ambient pressure = 1 bar. Take L=D=30cm. Determine (i) Mechanical efficiency
(ii) thermal efficiency (iii) Brake specific fuel consumption (iv) Brake mean effective pressure. Draw heat
balance sheet on % basis (july 2007)
Power supplied by electric motor= 1.5kW. ie FP=1.5Kw(given); N=500rpm;
Net loads on brake =225N ie ; N=500RPM =1m;
Rise in temperature of cooling water = 10oC ie Tco – Tci 10oC ; ; CV=43000kJ/kg;
AF=32; Cpg= 1.006kJ/kgK; 345oC; 25oC; L=D=0.3m

( )( ) ( )( )
T= = = 112.5 N-m
( )
BP: = =5.89 kW.
IP=BP+FP=5.89+1.5=7.39 Kw
= = 79.7%
Sfc= 2/5.89=0.339 m3/BP hr
mf =2kg/hr = kg/s

( )

( )
BP= , A= =0.071m2
= =0.33X105 kN/m2
Heat Balance sheet:
1. Heat input : mf X CV =(2/3600) X 43000
=23.89 kW
2. BP = 5.89 kW
mw=13.65kg/min = 13.65/60 kg/s
Qw=(13.65/60)X4.187x(10)
=9.52kW
:(2/3600)X(32+1) x1x(345-25)
: 5.87kW
: 23.89 – (5.89 + 9.52 + 5.87)
: 2.61 Kw

23.89 100 brake power 24.65
1. Heat input 5.89
9.52 39.85
coolant
5.87 24.57
exhaust gases
23.89 100 Total 23.89 100

Total
11.The following readings were recorded during a trial on a single cylinder, 4 stroke diesel engine. Bore =
150mm, stroke = 300mm, speed= 18000 revolutions per hour , Brake torque =200Nm. Indicated mean
effective pressure= 7bar, Rate of flow of cooling water through engine jacket = 5kg/min, Rise in
temperature of cooling water = 30oC, Fuel consumption= 2.04 kg/hr. calorific value of fuel used =
42MJ/kg; AF ratio = 22:1, Cp (gases) = 1.0kJ/kgK Exhaust gas temperature = 410 oC, Ambient temperature
= 20oC and ambient pressure = 1 bar.. Determine (i) Mechanical efficiency (ii) thermal efficiency (iii)
Brake specific fuel consumption (iv) Brake mean effective pressure. Draw heat balance sheet on minute
and % basis (Dec07/Jan 08)
Data:
D=150mm=0.15m; L=300m=0.3m; speed =18000rev per hr= rpm; T=200Nm; pm=7 bar;
mw=5kg/min; Rise in temperature of cooling water = 30 C ieTco – Tci 30oC; mf=2.04kg/hr;
o
CV=42MJ/kg=42000kJ/kg; AF=22; Cpg = 1.0kJ/kgK; 410oC ; 20oC; pa=1 bar
Solution:
If T is in Nm then BP:
If T is in KNm then
( ) ( )
BP: = =6.28 kW
IP= , A= =0.0176m2
N=18000rev per hr
N= =300 rpm
n= for 4 stroke engine hence n= =150 per min
( )
IP= x1= 9.24 kW
= = 67.96%
2.04kg/hr= kg/s

( )

( )
Sfc= 2.04/6.28=0.325 kg/BP hr
BP= , A= =0.0176m2
= =4.75X102 kN/m2
Heat Balance sheet:
1. Heat input : mf X CV =(2.04/3600) X 42000
=23.8 kW
2. BP = 6.28 kW
3. Heat carried by cooling water: mw Cpw (Tco – Tci)
=(5/60)X4.187x(30)
=10.47kW
:(2.04/3600)X(22+1) x1x(410-20)
: 5.083kW
: 23.8 – (6.28 + 10.47 + 5.083)
: 1.967 Kw
23.8 100 brake power 26.39
1. Heat input 6.28
10.47 43.99
coolant
5.083 21.36
exhaust gases
23.8 100 Total 23.8 100

Total
12. In a test of 4- cylinder, 4- stroke petrol engine of 80mm bore and 100mm stroke, the following
results were obtained at full throttle at a constant speed BP with all the 4 cylinders working = 14.7kW,
BP with cylinder No 1 is cut off = 10.1kW, BP with cylinder No 2 is cut off = 10.3kW, BP with cylinder No
3 is cut off = 10.2kW, BP with cylinder No 4 is cut off = 10.4kW. The fuel consumed at the rate of
5.44kg/hr Determine the (i) the indicated power, (ii) the indicated thermal efficiency if the calorific value
of the fuel = 41900kJ/kg, (iii) Relative efficiency based on IP if clearance volume in each cylinder = 100cc
=4Bt –(B1 +B2 +B3 +B4)=4 x14.7 – (10.1 +10.3 +10.2+10.4)
=17.8 Kw
mf=5.44kg/hr = kgs/s

( )
Vs= = =502.4 cm3per stroke
=6.024
=0.512
Relative efficiency= =0.549 or 54.9%

13. Morse test is conducted on a four stroke four cylinder petrol engine at a constant speed and the
following power is measured:
With all cylinder working =15kW
With number 1 cylinder cut off =11.1kW
The bore and stroke of each cylinder is 75mm and 100mm respectively. The clearance volume of the
cylinder is 100cc. The fuel is consumed at the rate 6 kg/hr. If the calorific vaue of the fuel is 42000kJ/kg.
Determine i) Indicated power ii) Frictional Power iii) Mechanical efficiency iv) Brake thermal efficiency v)
Relative efficiency with respect to brake thermal efficiency. (Dec 2010)
=4Bt –(B1 +B2 +B3 +B4)=4 x15 – (11.1 +11.3 +10.8+11)
=15.8 Kw
mf =6kg/hr= kgs/s
(iii) Indicated thermal efficiency= = = 0.227 or 22.7 %

( )

( )
Vs= = =441.5 cm3 per stroke
=5.415
=0.49
14. The following data refer to the test conducted on two stroke diesel engine, run for 20 minutes at full
load, Mean effective pressure = 3 bar, speed=350RPM, net brake load =650N, fuel consumption =1.52kg,
cooling water=160kg, water inlet temperature =30oC, water outlet temperature =52oC, air fuel ratio= 32,
room temperature= 25oC, exhaust gas temperature=300oC, cylinder bore=200mm, stroke =280mm,
brake drum diameter =100cm, calorific value of fuel=44000kJ/kg, steam formed per kg of fuel in the
exhaust=1.35kg, specific heat of steam in exhaust=2.09kJ/kgK, specific heat of dry exhaust gas =1kJ/kgK,
the pressure of exhaust = 1 bar, Determine: i) indicated power; ii) Brake power; iii) Mechanical efficiency
and also write the energy balance on Minute basis and percentage. (May/June 2010)
Duration 20 min
pm=3 bar;N=350rpm; net brake load =650N ie W ;
mf=1.52kg in 20 min = kg/min= kg/sec
mw=160kg in 20 min= kg/min; Tco=52oC ; AF=32
room temperature= 25oC ie TR=25oC ; Tex=300oC; D=200mm=0.2m; L=280mm=0.28m
brake drum diameter =100cm ie Db=1m; CV=44000kJ/kg
steam formed per kg of fuel in the exhaust=1.35kg ie of fuel
specific heat of steam in exhaust=2.09kJ/kgK,
specific heat of dry exhaust gas =1kJ/kgK ie
the pressure of exhaust = 1 bar; pa=1bar
Soution
( )( ) ( )( )
T= = = 325 N-m
( ) ( )
BP: = =11.9 kW
( )
IP= , A= =0.0314m2
n=N for 2 stroke hence n=350

( )
IP= = 15.39 kW
= = 77.3%
Heat Balance sheet:
mf =1.52kg in 20 min Hence mf = kg/min
1. Heat input : mf X CV =(1.52/(20)) X 44000

=3344 Kj/min
2. BP = 11.9 kWX60=714 Kj/min

mw =160kg in 20min
Hence mw=
=(160/(20X60))X4.187x(52-30)
=12.28kWX60=736.9 Kj/min
4. Heat carried by Steam: mass of steam X enthalpy or msCps (Tgo – Tgi)
steam formed per kg of fuel in the exhaust=1.35kg
Mass of steam formed : 1.35 x mass of fuel consumed per min =1.35 X(1.52/20) kg/min
=1.35 X(1.52/20) X2.09(300-25)=58.96Kj/min

5. Heat carried by exhaust gases : (mf ( )+ )-ms) Cpg (Tex – TR)
:(1.52/(20))(32+1))-( ( ))) 1(300-25)
=661.48Kj/Min
6. Heat un account for : 1 – (2+3+4+5)

: 3344 – (714 + 736.9 + 58.96+661.48)
: 1172.66Kj/min
brake power 21.35
1. Heat input 3344 100 714
736.9 22.04
coolant
Steam 1.76
58.96
661.48 19.78
exhaust gases
3344 100 Total 3344 100

Total
15. A 4 cylinder engine has the following data: Bore = 15cm, stroke = 15cm, Piston speed = 510m/min,
BP= 60kW, Mech efficiency= 80%, Mep = 5bar, CV= 40000kJ/kg. Calculate i) Whether this is a two stroke
or 4 stroke cycle engine (June/July 2009)
Data: D=15cm=0.15m; L=15cm=0.15m ; Mean piston speed =2LN=510m/s; BP= 60kW;
CV= 40000kJ/kg
= 1700 rpm
; 0.8 ,
IP=75Kw ; IP= xk, kW A= =0.0177m2
75= X4cylinder
n=847.45 explosion per min
N =1700rpm given
Comparing n and N it may be observed that n =
Hence engine is 4 stroke
16. Following data are available for SI engine, single cylinder stroke = 4. A:F=16:1, CV=45000kJ/kg, mech
efficiency =80%. Air std. efficiency = 50%, relative efficiency =70%, stroke to bore = 1.5,suction condition
= 1 bar, 30oC, speed = 2500rpm, BP= 75kW. Calcualte i) compression ratio ii) indicated thermal efficiency
iii) BSFC iv) Brake thermal efficiency v) Bore and stroke, assume vol efficiency = 80% (june/July 2009)
Data: AF=16; CV=45000kJ/kg;
stroke to bore = 1.5 ie ; suction condition = 1 bar, 30oC, N=2500rpm; BP= 75kW
CR=5.66
Indicated thermal efficiency=0.7X0.5 = 0.35
Indicated thermal efficiency=
; 0.8 ; IP=93.75Kw
= ; mf =0.00595 kg/s
Brake thermal efficiency= = = 0.28 or 28 %
BSfc= 0.00595X3600/75=0.2856 kg/BP hr
Mass of air=(0.00595)X22 =0.1309 kg/s
; =1.187 kg/m3
Vact=0.1309/1.189=0.11 m3/s
=0.9545
Vs= ( )= ( ) =0.9545 kg/m3
d=0.339m, L=1.5X0.339=0.508m
17. A 4 cylinder, 4 stroke SI engine 90mm bore and 90 mm stroke was tested at constant speed. The fuel
supply was fixed at 0.0008 kg/sec and plug of 4 cylinders were successively short circuited without
change of speed. The power measurement was as follows:
With all cylinders working 16.25kW
With 1st cylinder cut off 11.55kW

With 2nd cylinder cut off 11.65kW
With 3rd cylinder cut off 11.7kW
With 4th cylinder cut off 11.5kW
Find Indicated power, thermal efficiencies and relative efficiency if clearance volume is 65cm3 and CV is
42500kJ/kg.(Jan 2010)
=4Bt –(B1 +B2 +B3 +B4)=4 x16.25 – (11.55 +11.65 +11.7+11.5)
=18.6 Kw

( )
Vs= = =572.27 cm3/stroke
=9.8
=0.6
18.A four cylinder four stroke petrol engine has a bore 57 mm and a stroke 90 mm. Its rated speed is
2800 rpm and is tested at this speed against a brake which has a torque arm of 0.356m. The net brake
load is 155 N and fuel consumption is 6.74 lit/hr. The specific gravity of the petrol use is 0.735 and CV is
44200kJ/kg. A Morse test is carried out and the cylinders are cut in the order 1,2,3,4 with corresponding
brake loads are 111,106.5,104.2 and 111 N respectively. Calculate bmep, brake thermal efficiency,
specific fuel consumption, mechanical efficiency and imep.
Data: D=57mm=0.057m; L=90mm=0.09m; N=2800rpm; Torque Arm= 0.356m ie R=0.356m
The net brake load is 155 N ; =155N ;
fuel consumption is 6.74 lit/hr Vf=6.74 lit/hr
The specific gravity of the petrol use is 0.735 ie S=0.735; CV is 44200kJ/kg
A Morse test is carried out and the cylinders are cut in the order 1,2,3,4 with corresponding brake loads
are 111,106.5,104.2 and 111 N respectively
Ie ;
Solution
Torque = Brake Load x Torque Arm Length
Torque with all cylinders are working
T1,2,3,4= xR=155x0.356=55.18Nm
T234= xR =111x0.356=39.516Nm
T134= xR =106.5x0.356=37.914Nm
T124= xR= 104.2x0.356=37.095Nm
T123= xR= 111x0.356=39.516Nm
( )
BP1,2,3,4: = =16.17 kW
( )
BP234: = =11.5 kW
( )
BP134: = =11.11 kW
( )
BP124: = =10.87 kW
( )
BP123: = =11.5 kW
(ip)total =ip1 +ip2 +ip3 +ip4 = (BP1,2,3,4 – BP234)+( BP1,2,3,4– BP134)+( BP1,2,3,4 – BP124)+( BP1,2,3,4 – BP123)
= (16.17 11.5) +(16.17 11.5)+ (16.17 11.11)+( 16.17 10.87) +( 16.17 11.11)
=19.7 Kw
Brake thermal efficiency= =( = 0.265 or 26.5 %
)
( )
BP(kW)= , A= =0.00255m2 ; k=number of cylinder =4
n=number of working stroke theoretical= for 4 stroke
n= =1400working strokes per minute
BP= ie 16.17=
= = 7.549x102 kPa
IP= , A= =0.00255m2 ; k=number of cylinder =4
19.7=
= =9.19 102 kPa
19. A rope brake was used to measure the brake power of a single cylinder, 4 stroke petrol engine. It
was found that the torque due to brake load is 175Nm and the engine makes 500rpm. Determine the
brake power developed by the engine in horse power unit.(July2011).
( )
BP: = =9.16 kW
One Horse power =735W=0.735kW
BP= (9.16/0.735)=12.5HP
20.A test on two stroke engine gave the following results at full load: Speed=350rpm, Net brake
load=65kgf, mep=3bar, fuel consumption=4kg/hr, jacket cooling water flow rate=500kg/hr, jacket
cooling water temperature rise=200C, air used per kg of fuel=32kg, cylinder diameter=22cm,
stroke=28cm, effective brake drum diameter=1m, CV=43MJ/kg, Cp gases=1kJ/kgK, exhaust temp=4000C,
room temperature=200C.Find the mechanical efficiency and heat balance sheet in minute and % basis
(june2012).
Data:N=350rpm, Net brake load=65kgf ie W ;
= ; = =
jacket cooling water temperature rise=200C ie Tco – Tci=200C
air used per kg of fuel=32kg ie AF=32; D=22cm=0.22m; L=28cm=0.28m
effective brake drum diameter=1m ie Db=1m; CV=43MJ/kg=43000kJ/kg;
Cpg =1kJ/kgK; Tex=4000C; TR=200C
Solution:
( )( ) ( )( )
T= = = 318.83 N-m
( )
BP(kW):
( ) ( )
BP: = =11.7 kW
IP= , A= =0.038m2
n=N for 2 stroke engine, hence n=350
( )
IP= x1 = 18.62 kW
= = 62.8%
Heat Balance sheet:
1. Heat input : mf X CV =(4/(60))(kg/min) X 43000(kJ/kg)

=2866.67 Kj/min
2. BP = 11.7 kWX60=702 Kj/min

=(500/(60))X4.187x(20)
=697.8 Kj/min
:((4+4x32)/(60)) 1(400-20)
=836kJ/Min

: 2866.67 – (702 + 697.8 + 836)
: 630.87Kj/min
brake power 24.5
1. Heat input 2866.67 100 702
697.8 24.34
coolant
836 29.16
exhaust gases
5. Unaccounted losses 630.87 22
2866.67 100 Total 2866.67 100

Total
21.A test on single cylinder 4 stroke oil engine having bore 180mm and stroke 360mm gave the
following results: Speed 290rpm, brake torque=392Nm, IMEP=7.2bar, oil consumption=3.5kg/hour,
cooling water flow 270kg/hour, cooling water temperature rise=360C, air fuel ratio by weight=25,
exhaust gas temperature=4150C, barometric pressure=1.013bar, room temperature=210C, CV of
fuel=45200kJ/kg, fuel contains 15% of hydrogen by weight, calculate:1. The indicated thermal efficiency
2.Volumetric efficiency based on the atmospheric conditions 3. Draw the heat balance sheet in kJ/min
Take R=0.287kJ/kgK,Cp for gases=1.0035kJ/kgK, Cp for super-heated steam=2.093kJ/kgK.

( )
BP: = =11.89 kW
IP= , A= =0.025m2
n= for 4 stroke n= =145
( )
IP= x1= 15.66 kW
=3.5kg/hr=
Mass of air=(3.5/3600)X25 =0.0243 kg/s

=1.2 kg/m3
Vact= 0.0243/1.2=0.0202 m3/s
Vthe= ( )= ( ) =0.022 kg/m3
In the above equation is used since engine is 4 stroke
=0.9182
Heat Balance sheet:
1. Heat input : mf X CV =(3.5/(60X60)) X 45200

=43.94kWX60=2636.67 Kj/min
2. BP = 11.89 kWX60=713.4 Kj/min

mw=270kg/hr = kgs/s
=(270/(60X60))X4.187x(36)
=11.31kWX60=678.29 Kj/min
4. Heat carried by Steam: mass of steam X enthalpy or msCps (Tex – TR)
1 kg of hydrogen gives 9 kg of water
(0.15x3.5) H2gives =0.15x3.5x9=4.725kg/hour=0.0013125kg/s
HC by steam=0.0013125X2.093(415-21)=1.082kWX60=64.94Kj/min
5.Heat carried by exhaust gases : ((mf + ma )-ms) Cpg (Tex – TR)
:(3.5/(60X60))(25+1))-0.0013125) 1.0035(415-21)
:9.48X60=568.52Kj/Min
6. Heat un account for : 1 – (2+3+4+5)

: 2636.67 – (713.4 + 678.29 + 64.94+568.52)
: 611.52Kj/min
brake power 27.06
1. Heat input 2636.67 100 713.4
678.29 25.73
coolant
Steam 2.46
64.94
568.52 21.56
exhaust gases
2636.67 100 Total 2636.67 100

Total
Psychrometrics
Air conditioning is a simultaneous control of temperature, humidity, cleanliness, odour and air
circulation as required by the occupants of the space
Psychrometry is the study of properties of dry air and water vapor contained in moist air
Dry Bulb Temperature (DBT): Actual temperature of Moist air is called Dry Bulb Temperature.
This is measured by ordinary thermometer
Wet Bulb Tempeature (WBT): The wet Bulb temperature is the temperature recorded by a
thermometer when the bulb is enveloped by a cotton wick saturated with water
As the air stream flows past it, some water evaporates, taking the latent heat from the water
soaked wick, thus decreasing its temperature. This decreased temperature is recorded in
thermometer when the bulb is covered with wet cotton
If the saturated air flows past the thermometer it would not evaporate the water particles in the
wicked cotton (since air is saturated with water) Hence there is no decrease in the temperature
Hence for saturated air WBT=DBT
Wet Bulb Depression: Difference between Dry Bulb Temperature and Wet Bulb Temperature is
called Wet Bulb Depression
For saturated air wet Bulb depression is zero
Dew Point Temperature(DPT): is defined as the temperature at which the water contained in
moist air get condensed
Dew Point Temperature is read from the steam table as saturation temperature corresponding
to partial pressure of water vapor contained in moist air
Specific Humidity or absolute humidity or Humidity ratio:

It is defined as the ratio of the mass of water vapor in a given volume of the mixture to the mass
of the dry air present in the mixture
ω=
= x
= x ̅
But pa= pt -pv Ma=29; Mv=18
1
Relative Humidity: is defined as the ratio of mass of water vapor mw in a certain volume of moist
air at a given temperature to the mass of water vapour mw in the same volume of saturated air
at the same temperature
Φ= =
=
Note that pvs is read from steam table as the saturation pressure corresponding to Dry bulb
temperature
Degree of saturation: is defined as the actual specific Humidity of given air to the specific
humidity of saturated air at the same temperature of given air
μ=
=
μ=φ x
=φ x
φ= ( )
This is the relation between Degree of saturation and relative humidity
Relation between Absolute and relative humidity
φ=
But
φ =1.6ω
Carrier Equation
When DBT and WBT is given partial pressure of water vapor is calculated by Carrier equation
( ) ( ( ) )( )
Enthalpy of Moist Air

Enthalpy of Moist Air = Enthalpy of dry Air + Enthalpy of water vapor associated
h=hair+ωhvapor
hair=CpaTDBT where Cpa=1.005kJ/kgK
hvap=hg+Cpv(TDBT-TDPT) where Cpv=1.88 and hg=2500kJ/kg
Generally TDPT is neglected
Hence hvap=2500+1.88TDBT
2
Hence Enthalpy of Moist Air= 1.005TDBT +ω(2500+1.88TDBT)kJ/kg of dry air
Psycrometric Chart
Specific
Humidity line
Saturation Curve
Relative humidity Line

w
Constant Enthalpy Line ( WBT line)
DBT line
DBT
Psychrometric Chart
Pshycrometric Processes:
Sensible Heating:
Heating of air with no change in specific humidity is called sensible Heating. This can be achieved
by passing the air over a heating coil like electrical resistance heater or steam coils. DBT
increases while specific humidity remains constant.
Heater
Air filter
Air at 2
Air flow at 1
1 2
DBT
By Pass factor of Heating coil:

When one kg of air is made flow over the heating coil in a conduit some amount of air (Bkg ie
fraction of one kg of air) escapes without contacting coil. Due to this temperature of air after the
3
heating coil is less than the heating coil temperature due to mixing of air stream which made
contact with heating coil and air stream without contacting (By pass) heating coil.
Balancing the enthalpies
BCpT2’+(1-B) CpT1 = CpT2
B= where T2 is the temperature just after heating coil and T2’ is the temperature of heating
coil and T1 is the initial temperature
Sensible Cooling:
Cooling of air with no change in specific humidity is called sensible cooling. This can be achieved
by passing air over cooling coil like evaporating coil of refrigeration cycle. DBT decreases while
specific humidity remains constant
cooling Coil
Air filter
Air at 2
Air flow at 1
1
2
DBT
By Pass factor of cooling coil:

When one kg of air is made flow over the cooling coil in a conduit some amount of air (Bkg ie
cooling coil is more than the cooling coil temperature due to mixing of air stream which made
contact with cooling coil and air stream without contacting (By pass) cooling coil.
Balancing the enthalpies
BCpT2’+(1-B) CpT1 = CpT2
B= where T2 is the temperature just after heating coil and T2’ is the temperature of heating
coil and T1 is the initial temperature
Cooling and Dehumidification:
4
This process involves lowering the DBT temperature and specific humidity. Here air is cooled
below the Dew point temperature of air. During this process air is cooled till it reaches DPT of air.
Further cooling of air condenses the water vapor and water particles separates out from the
moist air. Hence specific humidity decreases.
cooling Coil
Air filter
Air at 2
Air flow at 1
moistur removed from air
h1
w1
1
h2
w
2
2
DBT
Air may be cooled and dehumidified a) by placing the evaporator coil across the air flow ii) by
circulating chilled water or brine in a tube placed across the air flow iii) by sparaying chilled eater
to air in the form of mist
By Pass factor of cooling coil:
When one kg of air is made flow over the cooling coil in a conduit some amount of air (Bkg ie
cooling coil is more than the cooling coil temperature due to mixing of air stream which made
contact with cooling coil and air stream without contacting (By pass) heating coil.
Cooling with Adiabatic Humidification of Air (Adiabatic Saturation Process):
The re-circulated water is sprayed into the air in an insulated chamber. A part of it evaporates in
trying to saturate the air. The heat required for the evaporation of water is removed from the air
itself which results in decrease its temperature. If the air leaving the humidifier becomes
saturated with water, then the temperature of air is called adiabatic saturation temperature.
5
Humidifier
Air filter
Air at 2
Air flow at 1
make up water
pump
along constnat enthalpy line

2
DBT
Chemical Dehumidification:
Air can be humidified by passing it over certain chemicals which have an affinity for moisture.
During this process of condensation of water vapor in the air liberates latent heat of evaporation
into air causing increase in Dry bulb temperature of air
along constnat enthalpy line

2
DBT
Mixing of Air Streams:

When air at one condition is mixed with air at another condition, the condition of the final
mixture is obtained on the psychrometric chart by a point on the line joining the points indicating
the orginal conditions ie 12
The exact location of the point depends upon the relative masses of dry air in the starting
condition
6
h3
w
h2
2 w2
h1
w3
3
1 w1
T1 T3 T2
DBT
Air at cindition 1
m1,h1, w1
m3,h3, w3
Condition of Air after mixing of 2 streams
m2,h2, w2
Air at condition 2
m3=m1+m2+m3
m1h1+ m2h2=( m1+m2)h3
=
m1ω1+ m2ω2=( m1+m2)ω3
Final state is to be found by dividing the lie 1-2 into segments proportional to the relative masses
of dry air before mixing takes place.
Comfort Air conditioning:
The following factor determine the comfort feeling of the occupants in an air conditioned space
1. Supply of Oxygen : Normally each person requires nearly 0.65m3 of oxygen per hour and
produces 0.2m3of CO2 . To comfort air conditioning CO2 level in the should be maintained
below 0.6%
7
2. Heat Removal: The Air conditioned space should absorb heat dissipated by persons and
appliances and reject heat to the surroundings to maintain the temperature of space within
the comfort zone DBT=25+1 to 25-1
3. Moisture Removal: Moisture loss of upto 50% from human body is commonly observed. The
air conditioned space to be maintained Relative humidity which is comfortable to occupants
ie RH 50%+5 to 50%-5
Summer Air conditioning for Hot and wet weather
Cooling coil
Hating coil
Air filter
Air at 2
Air flow at 1 Air at 3
water collected after dehuidification
The outdoor condition is first passed over the cooling coil so that it gets dehumidified and cooled
and comes out at point 2. The process is represented in psychrometric chart by 12 (Actual) Ideal
process is represented by 12’ where T2’ is the Dew point temperature of cooling coil.
( )
The capacity of cooling coil is= Ton of refrigeration
The air leaving the cooling coil is then passed over the resistance heating coil to get the required
comfort condition. It is represented by 23 on psychrometric chart
The capacity of heating coil = ma (h3- h2) kW
8
h1
h3 w1
1
h2
3'
2' 2
w
2
3
T' T T3 T' T
2 2 1
3
By pass factor of cooling coil =

By pass factor of heating coil =
Summer air conditioning for Hot and Dry weather
Cooling Coil
Humidifier
Air filter
Air at 2
make up water
pump
Air is first cooled from outdoor condition (Point 1) to point 2 by passing over a cooling coil
Cooling process is represented in Psychrometric chart by 12 (Actual Process) where as 12’ is ideal
process
( )
The capacity of cooling coil is= Ton of refrigeration
9
The air coming out of the coil at point 2 is passes into the adiabatic humidifier and the required
conditioned leaves the humidifier at point 3. This process is represented in psychrometric chart
by 23 and ideal process is represented by 23’
The capacity of Humidifier = ma (ω3-ω2) kg/sec
3' w
3 w3'
w3
2 1 w1=w2
2'
T' T T
2 2 1
DBT
By pass factor of cooling coil =

Humidifier Efficiency =
Winter Air conditioning:
heating Coil
heating Coil
Humidifier
Air filter
Air at 2 Air at 4
make up water
pump
The air is first passed over a preheater. The process is represented by 12 in psychrometric process.
Ideal process is represented by 12’
It is then passed through the humidifier where air absorbs moisture and humidity of air increases
as enthalpy remains constant. This represented by 23 in psychrometric chart.
10
and finally through a second heater where it is sensibly heated to achieve the desired condition.
This represented in psychrometric chart by 34
h4
w
h3
3'
3 4 4'
h1
1
2 2'
T1 T3' T3 T2 T2' T4 T4'
DBT
The capacity of heating coil 1= ma (h2- h1) kW
The capacity of Humidifier = ma (ω3-ω2) kg/sec
The capacity of heating coil 2= ma (h4- h3) kW
By pass factor of heating coil 1 =

By pass factor of heating coil 2 =
1. Moist air at 30oC , 1.01325 bar has a relative humidity of 80%. Determine without using the
psychrometric chart, (i) partial pressure of water vapor (ii) specific humidity (iii) specific
volume and (iv) Dew point temperature
Solution:
i) Partial pressure of water vapor
Φ=
Pvs is the saturation pressure at DBT
Saturation pressure at 30oC is 0.042415 bar
0.8 =
Pv=0.033932 bar
11
ii) Specific Humidity:
ω=
= 0.02155
iii) Specific volume:
( )
Density ρ =
( )
=
=1.1164kg/m3
Specific volume =
=0.89573 m3/kg
iv) Dew point temperature:
Is the saturation temperature at pv= 0.033932 bar ie 26oC
2. Atmospheric air at 101.325kPa has 30oCDBT and 15oDPT. Without using the psychometric chart , using
the property values from the tables, calculate i) partial pressure of air and water vapor ii) specific
humidity and iii) relative humidity iv) vapor density and v) enthalpy of moist air
Solution
i) partial pressure of air and water vapor
The partial pressure of water vapor at DPT ( 15oC) = 0.017039bar

Pv=0.017039 bar
Partial pressure of air Pa =Pt-Pv =1.01325 – 0.017039
Pa =0.996211 bar
ii) Specific Humidity
ω=
= 0.010638 kg/kg of dry air
iii) relative humidity

12
Φ=
Saturation pressure at 30oC is 0.042415 bar ie Pvs=0.042415
Φ= =0.40172
Φ = 40.172%
iv) Vapor density

Vapor Density ρ =
̅
=0.46188 as Mol wt of water 2+16 =18
( )
Density ρ =
= 0.012175kg/m3
v) enthalpy of moist air

h=1.005 TDBT +ω(2500+1.88TDBT)
=1.005 x30 +0.010638(2500+1.88x30)
=57.3449kJ/kg
3. The DBT and WBT of atmospheric air at 1 atm (1.01325bar) pressure are measured with sling
psychrometer and determined to be 25oC and 15oC respectively. Determine i) specific humidity ii)
relative humidity iii) enthalpy of moist air
Solution
i) specific humidity
( ( ) )( )
( )
( ) is the saturation temperature at WBT ie 0.01704 bar from steam table
( )( )
=0.01057 bar
ii) Specific Humidity
ω=
13
= 6.5569x10-3 kg/kg of dry air
iii) relative humidity

Φ=
Saturation pressure at 25oC is 0.03166 bar ie Pvs=0.03166 bar
Φ= =0.3338
Φ = 33.38%
iv) enthalpy of moist air

h=1.005 TDBT +ω(2500+1.88TDBT)
=1.005 x25 +6.5569x10-3 (2500+1.88x25)
=41.8254 kJ/kg of dry air
4. A room measures 5m x5m x 3m. It contains atmospheric air at 100kPa , DBT =30oC and relative
humidity = 30%. Find the mass of dry air and the mass of associated water vapor in the room. Solve
the problem without the use of psycrometric chart and using the properties of water vapor from
steam tables
Solution
Volume of room = 5x5x3 =75m3

Pt =100 kPa = 1bar
DBT =30oC
Relative humidity Φ = 30%.
Φ=
Saturation pressure at 30oC is 0.042415 bar ie Pvs=0.042415
0.3 =
= 0.012726 bar
Mass of dry air in moist air
( )
ma =
( )
ma =
14
=86.2345kg
Mass of vapor in moist air
mv =
̅
=0.46188 as Mol wt of water 2+16 =18
( )
mv =
=0.7556 kg
5. 30m3/min of air at 15oC DBT and 13oC WBT is mixed with 12m3/min of air at 25oC DBT and 18oC WBT.
Calculate DBT, specific humidity of the mixture. Take atm pressure of 760mm of Hg. Calculate by calculation
method only.
Moist Air at V1=30m3/min TDBT1=15oC TWBT1=13oC

Moist Air at V2=12m3/min TDBT2=25oC TWBT2=18oC
Mixed each other
For Moist air TDBT1=15oC TWBT1=13oC
( ( ) )( )
( )
( ) is the saturation temperature at WBT 13oC ie 0.01497 bar from steam table
Pt =760mm of Hg ie 1.013 bar
( )( )
=0.01366 bar
Specific Humidity
ω1 =
enthalpy of moist air

h1=1.005 TDBT + ω1 (2500+1.88TDBT)
=1.005 x15 +8.493x10-3 (2500+1.88x15)
=36.547kJ/kg of dry air
Mass of air
( )
ma1 =
15
( )
ma1 =
ma1 =0.60331 kg/s
For Moist Air at V2=12m3/min TDBT2=25oC TWBT2=18oC
( ( ) )( )
( )
( ) is the saturation temperature at WBT 18oC ie 0.01604 bar from steam table
Pt =760mm of Hg ie 1.013 bar
( )( )
=0.01604 bar
Specific Humidity
ω2 =
enthalpy of moist air

h2=1.005 TDBT2 + ω2 (2500+1.88TDBT2)
=1.005 x25 +9.9976x10-3 (2500+1.88x25)
=50.588kJ/kg of dry air
Mass of air
( )
ma2 =
( )
ma2 =
ma2 =0.2352 kg/s
For mixing of 2 air streams
m1ω1+ m2ω2= m3ω3
ω3=
ω3=
=8.915x10-3 kg/kg of dry air
Similarly m1h1+ m2h2= m3h3
h3=
16
( ) ( )
h3=
=40.485kJ/kg
h3=1.005 TDBT3 + ω3 (2500+1.88TDBT3)
40.485=1.005 TDBT3 + 8.915x10-3 (2500+1.88TDBT3)
TDBT3=17.809oC
6. It is required to design air conditioning plant for an office room with the following conditions
Outdoor conditions: DBT=14oC, WBT=10oC; Required conditions: DBT= 20oC , 60%RH
Amount of air circulation is 0.3m3/min/person, seating capacity of the office=60,
The required condition is achieved by heating and adiabatic humidification. Determine
i) Heating capacity of coil in kW
ii) Surface temperature required if by pass factor of the coil is 0.4
iii) Capacity of the dehumidifier
Data: Outdoor conditions: DBT=14oC, WBT=10oC Required conditions: DBT= 20oC , 60%RH
Required condition is achieved by heating and adiabatic humidification
Solution:
First Locate the point in the Psychrometric chart corresponding to Outdoor conditions and locate
point 3 according to Indoor condition.
1-2 is heating and 2-3 is Adiabatic humidification line

From 1 draw a horizontal line and from 3 draw a line along constant enthalpy line. Intersection of
2 lines is 2
Then read from chart note down h, ω and also note down the DBT temperature at 2 as shown in
figure
h1=29.5kJ/kg; ω1=ω2=0.006;
h2=43kJ/kg; T2=26.5;
h3=43kJ/kg; ω3=0.009
17
h2=h3=43
3 60%
0.009
h 1 =29.5
1 2 2'
0.006
10C WBT line
10 C 14 C 20 C 26.5C T2'
i) Heating coil capacity in kW

ma (h1-h2)
( )
ma =
Amount of air circulated is0.3m3/min/person

Total air circulated for 60 persons = 0.3x60 m3/min = m3/sec =0.3 m3/sec
V=0.3 m3/sec
Specific Humidity at outdoor condition =0.006kg/kg of dry air
ω=
0.006 =
Pv=0.00987bar
( )
ma = =0.365 kg/s
Heating capacity of cooling coil =ma(h1-h2)= 0.365(43-29.5) =4.2975kW
ii) Surface temperature required if by pass factor of the coil is 0.4
0.4
Surface temperature of heating coil T2’ =34.83oC
iii) Capacity of humidifier: ma(ω1-ω2)

= 0.365(0.009-0.006) = 0.001095kg
18
7. Saturated air at 2 oC is required to be supplied to a room where the temperature must be held at 20oC
with relative humidity of 50%. The air is heated and then water at 10o C is sprayed in to give required
humidity. Determine the temperature to which the air must be heated and the mass of spray water
required per m3 of air at room conditions . Assume that the total pressure is 1.013 bar
Data:
Out door conditions: Saturated air means 100% RH ; DBT=2oC
Indoor conditions: DBT=20oC ; RH=50oC
The air is heated and then water at 10o C is sprayed in to give required humidity. Means water at 10oC
is used to humidify air leaving heater. Hence there is no significance to 10oC
Volume of air is =1m3
Solution:
First Locate the point 1 in the Psychrometric chart corresponding to Outdoor conditions and locate
point 3 according to Indoor condition.
1-2 is heating and 2-3 is adiabatic humidification line

From 1 draw a horizontal line and from 3 draw a line along constant enthalpy line. Intersection of
2 lines is 2
Then read from chart note down h, ω and also note down the DBT temperature at 2 as shown in
figure
h1=13kJ/kg; ω1=ω2=0.00425kg/kg of dry air;
h2=40kJ/kg; T2=28oC;
h3=40kJ/kg; ω3=0.0075 kg/kg of dry air
i) the temperature to which the air must be heated is T2=28oC
ii) mass of spray water required per m3 of air at room conditions

Air 1 m3 supplied at room conditions (Indoor conditions)
ω=
0.00425 =
Pv=0.00697
( )
ma =
( )
ma = =1.27 kg/s
Capacity of humidifier: ma(ω1-ω2)

= 1.27(0.0075-0.00425) = 0.0041275kg of water ( to be sprayed)
19
h2=h3=40
3 50%
0.0075
h 1 =1 3
0.00425
1 2
2C 20 C 28 C
8. A summer air conditioning system for hot and humid weather (DBT =32oC and relative humidity =70%)
consists in passing the atmospheric air over a cooling coil where the air is cooled and dehumidified .
The air leaving the cooling is saturated at the coil temperature It is then sensibly heated to the
required comfort condition of 24oC and 50% RH by passing it over an electric heater and then
delivered to the room. Sketch the flow diagram of the arrangement and represent the processes
undergone by air on a Skelton psychorometric chart and determine (i) The temperature of the cooling
coil (ii) The amount of moisture removed per kg dry air in the cooling coil iii)the capacity of cooling
coil and iv) the heat added per kg dry air in the heating coil.
Data;
Outdoor condition: DBT =32oC and relative humidity =70%
Indoor conditions: DBT =24oC and 50% RH
Process is cooling and dehumidification followed by reheating
First Locate the point 1 in the Psychrometric chart corresponding to Outdoor conditions and locate
point 3 according to Indoor condition
From 1 draw a horizontal line to intersect saturation line and from 3 draw a horizontal line to
intersect saturation line at 2 as shown in figure
20
h1 =87
70%
h3=48.5 w1 = 0.021
1
h2 =38
50% w =0.00925
2
2 3
o 0 o
14 C 24 C 32 C
The temperature of cooling coil =14oC

h1=87kJ/kgK; ω1=0.021kg/kg of dry air
h2=38kJ/kg; ω2=ω3=0.00925
h3=48.5 kJ/kg
i) The temperature of the cooling coil from psychrometric chart is 14oC
ii) The amount of moisture removed per kg dry air in the cooling coil
ma(ω1-ω2)=1(0.021-0.00925)=0.01175kg of water
iii) the capacity of cooling coil per kg of dry air = ma(h1-h2)=1(87-38)=49kJ/kg of dry air
iv) the heat added per kg dry air in the heating coil= ma(h3-h2)=1(48.5-38)=10.5kJ/kg of dry air
9. An air-conditioning system is designed under the following conditions: Outdoor conditions: 30oC DBT,
75% RH, Required conditions: 22oC DBT, 70%RH, Amount of free air circulated 3.33m3/s, Coil dew
point temperature (DPT) = 14oC. The required condition is achieved first by cooling and
dehumidification and then by heating. Estimate i) the temperature of air leaving heating coil (ii) The
capacity of cooling coils in tons of refrigeration (iii) The capacity of heating coil in kW (iv) The amount
of water vapor removed in kg/hr
Solution:
Data:
Outdoor condition: DBT =30oC and relative humidity =75%
Indoor conditions: DBT =22oC and 70% RH
Amount of free air circulated 3.33m3/s
Process is cooling and dehumidification followed by reheating
First Locate the point 1 in the Psychrometric chart corresponding to Outdoor conditions and
locate point 3 according to Indoor condition
Locate DPT of Cooling coil on saturation curve by drawing vertical line through 14 oC DBT to
intersect saturation curve at 2’
Join 1-2’
From 3 draw a horizontal line to cut 1-3 at 2 as shown in skelton psychrometric chart
From 1 draw a horizontal line to intersect saturation line and from 3 draw a horizontal line to
intersect saturation line at 2 as shown in figure
21
h1 =82
75%
h3=53 w1 = 0.02
1
h2 =47
2' 2
70% w =0.012
2
3
14o C 16.5 C 22 0C
o
30 C
h1=82kJ/kgK; ω1=0.02kg/kg of dry air
h2=47kJ/kg; ω2=ω3=0.012 kg/kg of dry air
h3=53 kJ/kg
i) The temperature of air leaving the cooling coil =16.5oC
ii) the capacity of cooling coil per kg of dry air = ma(h1-h2)=1(87-38)=49kJ/kg of dry air
ω=
0.02 =
Pv=0.03366 bar
( )
ma =
( )
ma = =3.75 kg/s
the capacity of cooling coil = ma(h1-h2)=3.75(82-47)=131.3kJ/sec
= =37.51 TOR
iii) the heat added per kg dry air in the heating coil= ma(h3-h2)=3.75(53-47)=22.5kJ/sec
iv) The amount of moisture removed per kg dry air in the cooling coil
ma(ω1-ω2)=3.75(0.02-0.012)=0.03kg of water/sec=108kg of water
10. Air at 0oC DBT and 90%RH has to be heated and humidified to 25oC and 40%RH by the
following method. By generating, adiabatic saturation in a recirculated water air washer to
90%RH and then reheated to final state. Find (i) The total heating required and the
humidifying efficiency of the recirculated air water washer, show the process on
psychrometric chart.
22
h4=45.5
h3= h2=32.5
90% 1
3 4 0.0075
40%
h1=8 3
1 90%
2
0.003
2
0C T2=?= 24 25 C
11. The following conditions are given for a hall to be air conditioned outdoor conditions=40oC
DBT, 20oC WBT, Required comfort conditions 20oC DBT 60%RH. Seating capacity of hall
=1500. Amount of outdoor air supplied =0.3m3/min per person. If the required condition is
achieved first by adiabatic humidification and then by cooling, estimate
i) The capacity of the cooling coil in tons
ii) The capacity of the humidifier in kg/hr
iii) An hall to be air conditioned with the following conditions, Out door conditions
400DBT and 200WBT; Required conditions 200DBT and 60%RH; amount of air
circulated 0.3m3/min/person;seating capacity 1500;required condition is achieved first
by adiabatic humidifying and then by cooling, determine1.capacity of cooling coil in
tons 2.capacity of humidifier in kg/hr(july 2008/Dec2011)
From chart at point a,wa=0.0065, Va=0.895, ha=58,

At point b, ,Wb=0.009,hb=58,
At point c, hc=43
( )
( ) ( )
23
12. 40m3/min of air at 310DBT and 18.50WBT is passed over the cooling coil whose surface
temperature is 4.40C. The coil cooling capacity is 3.56 tonnes of refrigeration under the given
condition of the air. Determine the DBT of the air leaving the cooling coil and by pass
factor.(July2012).
From chart: w1= 0.0079, h1=50kJ/kg,v1=0.873

Refrigeration capacity:3.56x3.5=12.46kW
( )
( ) ( )
hc=33.69
on the chart locate point c, DBT at c=17.10C
13. Saturated air at 2oC is required to be supplied to a room where the temperature must be held at
20oC with relative humidity of 50%. The air is heated and them water at 10o C is sprayed in to
give required humidity. Determine the temperature to which the air must be heated and the
mass of spray water required per m3 of air at room conditions. Assume that the total pressure is
1.013 bar(Jul2005)
From chart w1=0.0044, wc=0.0073,v3=0.84(exit point is taken)
24
Amount of water added=
From chart locate point b, and temperature at b Tb=27.50C.
14. The dry and wet temperature of atmospheric air at 101.325kPa pressure are measured with a
sling psychrometer and determined to be 250C and 150C respectively, determine
DBT,RH,Specific humidity and enthalpy.(June2012).
From steam table at 250C DBT, Pvs=0.03166bar=3.166kPa

AT 150C DBT, Pvswbt=0.01704bar=1.704kPa
( p  pswbt )(tdb  t wb )
p  ( PVS ) wbt 
1547  1.44t wb
( )( )
( )
Pv=1.051kPa
At 0.001051bar or 1.051kPa DPT from steam table is 7.50C.
( )
( )
h=41.68kJ/kg
15. Saturated air leaving the cooling section of an air conditioner at 140C DBT at the rate of
50m3/min is mixed adiabatically with the outside air at 320CDBT and 60% RH at the rate of
20m3/min. Assuming the mixing process occurs at a pressure of 1 bar, determine the
DBT,RH,specific humidity and volume flow rate of mixture.(June2010).
From chart v1=0.815, v2= 0.89,h1= 39, h2=78
25
( ⁄ )
( ⁄ )
( )
h3=49.5kj/kg
From h3 locate point 3 on chart and get the values
DBT=190C, w=0.0125kg/kg,RH=90%
16. Atmospheric air at 101.325kPa has 35oCDBT and 15oDPT. calculate RH,Specific humidity and
enthalpy take Cpv=1.88kJ/kgK(July2009)
From steam table at 350C DBT, Pvs=0.05628bar=5.628kPa
150C DPT, Pv=0.01704bar=1.704kPa
Pa=99.621kPa
( )
( )
h=62.5kJ/kg
26

Applied Thermodynamics C211 PDF

Uploaded by

Copyright:

Available Formats

Applied Thermodynamics C211 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Applied Thermodynamics C211 PDF

Uploaded by

Copyright:

Available Formats

1. What do you understand by the Air standard efficiency?

2. State the assumptions made in air standard cycle analysis

The efficiency of the Carnot engine is given by,

1-2 Process Adiabatic

2-3 Process: Isothermal Heat addition

4-1 Process: Isothermal Heat Rejection

Substituting in efficiency formula

1-2 process adiabatic

3-4 process adiabatic

Comparing i) and ii)

Work ratio is define as ratio of net work done to positive work

1-2 Process is adiabatic

Process 1–2: Gas is compressed isentropically. Q=0

Let Compression ratio , Cut off ratio , Expansion Ratio

1-2 adiabatic process

2-3 Process is constant Pressure process =

3-4 Adiabatic process

Substituting i) ii) and iii) in A

Process 1–2: Gas is compressed isentropically. Q=0

Process 4–5: Gas expands isentropically to point 4. Q=0

Let Compression ratio , Cut off ratio , Expansion Ratio

1-2 process adiabatic

2-3 process constant volume

3-4 constant pressure process

4-5 process adiabatic

R= gas constant, r=compression ratio

1-2 process adiabatic

2-3 process constant volume

R= gas constant, r=compression ratio

1-2 adiabatic process

2-3 process (constant volume process. )

3-4 process (adiabatic process)

R= gas constant, r=compression ratio

1-2 process adiabatic

2-3 process constant volume

3-4 process constant pressure process

4-5 process adiabatic

It is seen from the T-s diagram, area A14B ( Area A1”5”C

It is seen from the T-s diagram, area A23B ( Area

It is seen from the T-s diagram, area A14B ( Area

But ( ) from problem 14.

But ( ) from problem 14.

The pressure after isothermal compression is 3.5 bar, P1=3.5bar

the pressure after isentropic compression is 10.5 bar. P2=10.5bar

1-2 Process adiabatic

Work Net /kg=

2-3 Process is Isothermal

4-1 Process is Isothermal

=1x0.287x394.2 x =141.73 kJ/kg

=1x0.287x288 x = 103.54 kJ/kg

Wnet= 141. 103.54 = 38.19kJ/kg

The initial pressure before the beginning of compression is 101kPa at 340K.

The pressure at the end of heat addition process is 3.5Mpa.

Engine bore is 300mm and clearance volume 4x10-3m3.

Ie refering from origin of pv diagram where =

After 5/8th of the compression stroke, the pressure is 3.5 bar

For maximum work, ( )

The clearance volume is 0.01052m3 Vc=0.01052m3

the compression ratio is 16. Ie Rc=16