Professional Documents
Culture Documents
Cylinder Head - Install: Disassembly and Assembly
Cylinder Head - Install: Disassembly and Assembly
Previous Screen
Welcome: r080ec17
Product: WHEEL LOADER
Model: 950H WHEEL LOADER M1G00252
Configuration: 950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY
C7 Engine
i02304034
Installation Procedure
Table 1
Required Tools
NOTICE
Keep all parts clean from contaminants.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 1/4
13/4/2019 950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEBP4274 - 73) - Documentation
Illustration 1 g01153645
Illustration 2 g01153662
Note: To avoid damage to the cylinder head gasket, use guide bolts of an appropriate size to install the
cylinder head.
2. Attach a suitable lifting device to cylinder head (11). The weight of cylinder head (11) is
approximately 175 kg (385 lb). Position cylinder head (11) onto the cylinder block.
3. Apply Tooling (A) to the threads and both sides of the washers of bolts (12). Apply Tooling (B) to the
threads and both sides of the washers of bolts (13). Install bolts (12) and bolts (13) .
a. Tighten Bolt (1) through Bolt (14) in a numerical sequence to a torque of 300 ± 15 N·m (221 ±
11 lb ft).
b. Loosen Bolt (1) through Bolt (14) until the washers are loose under the bolt heads.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 2/4
13/4/2019 950H Wheel Loader M1G00001-UP (MACHINE) POWERED BY C7 Engine(SEBP4274 - 73) - Documentation
c. Tighten Bolt (1) through Bolt (14) in a numerical sequence to a torque of 130 ± 15 N·m (95 ± 11
lb ft).
d. Tighten Bolt (1) through Bolt (14) again in a numerical sequence to a torque of 130 ± 15 N·m
(95 ± 11 lb ft).
e. Turn Bolt (1) through Bolt (14) in a numerical sequence for an additional 90° (1/4 turn).
f. Tighten Bolt (15) through Bolt (20) in a numerical sequence to a torque of 55 ± 7 N·m (41 ± 5 lb
ft).
Illustration 3 g01153600
5. Connect tube assembly (8) and tube assembly (10) to turbocharger (9) .
Illustration 4 g01153599
Illustration 5 g01153598
End By:
a. Install the fan drive mounting group. Refer to Disassembly and Assembly, "Fan Drive Mounting
Group - Remove and Install".
b. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Install".
c. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft And Pushrod
- Install".
d. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve Mechanism
Cover Base - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc. Sat Apr 13 2019 19:43:06 GMT-0500 (hora estándar de Perú)
All Rights Reserved.
r080ec17
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpa… 4/4