EHV Cables,

Accessories & Services

POWERING THE NATION

Evolving Technology. Energizing Lives.
www.ravingroup.com
 With a strong presence across the power and energy
sectors, Ravin Group, established in the year 1950
has carved a niche for itself in the domestic and
global market as Power Experts. Ravin Group
comprises of various companies which are involved in
various and diverse businesses such as manufacture
of Energy Cables, EHV Cables and Installation,
Solar Energy Systems, Retail Energy Products
and Online Moisture Management Systems for
Transformers. The Group has continuously evolved
from manufacturing of Energy Cables, to EHV
Installation Services, to Renewable Energy Solutions,
and to Retail Energy Products.
At Ravin, the focus remains to embrace Evolving
Technology and to Energising Lives.

Our Vision
The Group is dedicated to maintaining its large global presence. The Group upholds its culture of care, trust,
empowerment and constant learning while meeting expectations of employees, stakeholders and society.

Our Mission
We at Ravin Group are committed to give our customers the best possible products & services at most
competitive prices as per agreed standards and within the stipulated time frame, to their entire satisfaction.
We shall strive relentlessly towards a zero defect culture through the commitment of each and every member of
our Company.
And of course, we shall not stop there, but keep on going.

1
 OUR VALUES

Our strongly imbibed core values of Safety, Dependability and Sustainability comes across as our
strength and the basis of our growth and development across the decades of our operation.

Safety
¾ Our products always adhere to international safety standards. SAFETY to the users, the public in general,
our employees and the environment is our priority

¾ Safety coincides with production and quality and is an integral part of our business

¾ A series of pioneering safety innovations has made Ravin a leader in safety over the past few years

Dependability
¾ We realise the importance of customer satisfaction which is a result of unmatched DEPENDABILITY

¾ Dependability is living up to our word and fulfilling our promises

¾ Dependability is supplying products which do not fail

¾ Our customers, employees, and communities deserve our respect, honesty, and expert abilities

¾ When a project is completed, our goal is to be remembered as a trusted partner that delivered the promised
results. And to be relied on again

Sustainability
¾ SUSTAINABILITY for us is an approach that integrates people, planet and profit, resulting in a greener and
safer tomorrow

¾ Sustainability involves our ongoing commitment to communities, stakeholders, the environment, health and
safety and the economic performance of our business

¾ Our aim is to promote a responsible culture and implement robust corporate systems to consistently meet our
sustainability goals

¾ We understand that best practice in these areas will help us to be a leading, international, diversified,
upstream, products company

¾ That is why we are working towards integrating sustainability practices across all our operations and business
activities so they can grow in the same manner and pace

2
 UNMATCHED ENGINEERING FINESSE

In providing a unique approach to process design, construction and project management, Ravin's engineering
expertise, production and process knowledge can provide a range of services to meet requirements like:

¾ Feasibility Study ¾ Design

¾ Customised Manufacturing ¾ Equipment Supply

¾ Installation ¾ Commissioning

Through our process, engineering prowess and reputation, we can

deliver a diverse range of process solutions to both domestic and
overseas markets.

Our customer base extends to major national and international

companies, worldwide private and public sector clients, all of whom
have benefited from our ability to adapt technologies and tailor our
services to meet the specific requirements of a project.

3
 OUR VARIOUS VERTICALS

Energy Cables
Ravin is involved in the manufacture of technology-driven energy
cables. We offer a complete range of cabling solutions for LV,
MV, HV, EHV cables from 1.1 kV to 220 kV from state-of-the-
art manufacturing units in India and U.A.E. Ravin also provides
allied services like Cable Jointing, Cable Laying and other
specialised services.

EHV Projects, Services and Accessories

Provision of a wide range of solutions including design,
manufacturing, installation and maintenance of Extra High
Voltage Cables for power transmission directly from power plant
sites to primary distribution network.

With its stellar expertise, Ravin Infraproject installs premoulded

joints and terminations for all voltages from 11 kV onwards to 400
kV in India with the support of a fully trained and certified jointing
team with an experience of thousands of joints and terminations.

Power Equipments
Ravin provides comprehensive moisture management system
solutions for power transformers and are the exclusive authorised
manufacturers of TRANSEC, UK, in India. TRANSEC is a high
end Molecular Moisture Management System which is designed
and manufactured in the UK.

Retail Energy Products

Ravin Group has recently ventured into highly advanced and forward looking vast retail energy market, which has a
huge customer base because of the various smart communication and battery driven devices being offered today.
The 'energy solutions' market is particularly meant for people on the go, as well as for the rural market which does
not have access to electricity.

RAVIN RETAIL ENERGY PRODUCTS comprise of three categories namely: Power Banks, Solar Chargers and
Solar Lanterns which provide a smart and convenient new way to charge smart phones, mobiles, tablets or Ipads,
MP3 players etc. Homes, shops, offices can be lit and powered, specially in locations where it is not possible, or
predictable, to get conventional power points. Thanks to Ravin’s Energy Products, homes can be powered and
devices fully charged
rged for days without access to conventional sources of electricity.

4
Renewable Energy
At Ravin, we are committed to fulfil the demand-supply gap of
the Indian energy sector by harnessing the unlimited energy of
the sun.

Today, the world is facing a threat of exhaustion of fossil fuels.

Sun, being the biggest power plant in our galaxy, is always
available to provide clean and reliable energy to the world.
We believe that this same solar power will shape the future of
our planet - providing a cleaner and greener alternative to the
conventional sources of energy.

Our global approach and research in technology is aimed

towards delivering sustainable and efficient solar solutions to
all our clients. Improving solar module efficiencies while holding
down the cost per cell is an important goal for us. We are also
working towards innovation and quality process and products,
thus raising the bar - for ourselves and the industry.

Tracking Systems
Ravin has recently introduced an innovative and path-breaking
tracking system which is a device that orients various solar
energy generating components towards the direction of the
sun. The revolutionary tracking systems help increase your
energy yield up to 15% to 35% with its innovative design, thus
increasing your ROI.

We Operate as an Integral Business Unit

„ Commercial & Tendering Team
„ Project/Contract Management Team
„ Systems Design/Installation Engineering
„ Full range capability for installation & tools supported by
logistics team
„ Full in-house testing & commissioning capability - specialised
facilities, testing engineers
„ Capability to execute turnkey projects up to 400 kV

5
 INTRODUCTION
The energy market has changed dramatically over the last few years as a consequence of deregulation,
privatisation and unbundling of generation and transmission. The new network owners mainly focus on the
cost-effectiveness of their assets. This applies to new network investments but, certainly, also includes the
optimisation of usage of the existing underground network. The design of a High Voltage underground system is
extremely important and requires an in-depth knowledge of cables, accessories, methods of installation, the fault
current of the system and impact on the electrical network. Ravin specialises in providing total management of
major projects and offers to its customers a complete turnkey approach, from system planning to final testing and
post-sales services. Installation design and methods, co-ordination and scheduling of installation activities, are
as crucial as the manufacture of cables and accessories to achieve a reliable and satisfactory connection. Ravin
operates to the highest accreditation and safety standards to meet the demands of the most complex project
environments. Turnkey approach, worldwide experience, top class customer references and strong focus on
innovation represent the winning recipe that makes Ravin a world leader in HV systems. The effective management
of the existing networks require different knowledge and experience, as they are often of hybrid nature (fluid filled,
gas insulated and XLPE extruded cables).
As India marches forward power becomes an essential ingredient for infrastructural development. With rapid
urbanisation around the corner to sustain the industrial growth, the necessity of transmitting large blocks of power
to load centres assume significance. Over the years, there has been a marked increase in the voltage level for
transmission of bulk power, due to the distinct advantages offered by the use of high voltage.
Necessity for EHV Transmission: With increase in transmission voltage, for the same amount of power to be
transmitted, the current in the line decreases which reduces I2R losses. This leads to increase in transmission
efficiency. With decrease in transmission current, size of conductor required reduces which decreases the size
of conductor. The transmission capacity is proportional to square of operating voltages. Thus the transmission
capacity of line increases with increase in voltage. With increase in level of transmission voltage, the installation
cost of the transmission per km decreases. It is economical with EHV transmission to interconnect the power
systems on a large scale. The number of circuits and the land requirement for transmission decreases with the
use of higher transmission voltages. Over the years, there has been a marked increase in the voltage level for
transmission of bulk power, due to the distinct advantages offered by the use of high voltage. This had ushered in
the generation of Extra High Voltage (EHV) power transmission systems with voltage grades of 66 kV and above.
Underground EHV cables are also used for evacuating bulk power generated in pumped storage hydroelectric
power generating stations, situated at a lower altitude, at outdoor switchyard located at a higher altitude. Similarly,
underground cable systems are the appropriate means of power transmission over short distances where erection
of overhead tower lines would be infeasible considering the space constraints.
It is in this context that Cross-linked Polyethylene (XLPE) insulated cables offer significant advantages. As an
insulating material, XLPE combines the advantages of improved mechanical and thermal properties with excellent
electrical characteristics of high dielectric strength, low relative permittivity and low dielectric losses. These
advantages have rendered what XLPE cables can achieve today - carrying large currents at voltages up to
500 kV, with an inherent higher short circuit withstand capacity of 250oC. Additional benefits that occur are simple
construction, easy installation and trouble-free operation.

6
 EHV cables come in different combinations as per the features mentioned in chart below:

Conductor Metallic Sheath Outer Sheath Optional DTS System

Aluminium Laminated Foil
Copper Laminated Foil
Fibre Optic Cable
Corrugated Aluminium
Aluminium/Copper PVC/HDPE embedded in main cable/
Lead Sheath FOC laid separately

Lead Sheath + Copper Wire +

Aluminium Wire

Conductor
HV XLPE CABLE
METALIC SHEATH/ SCREEN Extruded S.C.

TRADITIONAL HV/ EHV XLPE Insulation

CONSTRUCTIONS Copper Wires +
Extruded S.C. Aluminium Foil

Advantages Disadvantages
Swellable Tape
Weight Not Fully
Copper Wires Good Thermal Protected
Corrugated Aluminium Behaviour Against Water
Sheath Swellable Tape Penetration
Compact Cable
PE Outer Sheath
Aluminium Bonded Foil

PE Outer Sheath

Extruded Lead
Extruded Lead Alloy
PE Outer Sheath Advantages Disadvantages
Extruded Corrugated Aluminium
Well Known Very Heavy Weight
Advantages Disadvantages Solutions Ð
Short Lengths
Gap Between S.C. Thermal on Drum, More Joints
Less Weight
and Alu. Tube Behaviour more Costly Cables.
Good Mechanical
Strength of Current Carrying
the Screen. Capacity Weight Comparison for a 220 kV
Cost Effective Lesser by 5% 2500 mm2 Copper Cable 63 kA - 1s
Solutions
Ex Corr Ext Lead Al-Foil
41,6 kg/ m 65,6 kg/ m 40,4 kg/ m

7
EHV Cable Design

The 3 fundamental components of an EHV cable:

(1) Conductor
(2) Insulation System (Conductor screen, Insulation and Insulation screen)
(3) Metallic Screen/Sheath requirements

(1) DESIGN OF THE CONDUCTOR

The 2 basic Design drivers for designing the conductor are:
(a) Current Rating (continuous operation and short circuit)
(b) Mechanical Behaviour (flexibility, pulling strength)

(a) Current Rating depends on:

t
%$
SFTJTUBODF
DIPJDF
PG
NFUBM
BOE
DSPTT
TFDUJPO
BSFB
$4"


CSA = depends on maximum DC resistance (IEC 60228) or minimum weight (US standards)


t
"$
SFTJTUBODF
EFQFOET
PO
DIPJDF
PG
DPOTUSVDUJPO
TUSBOEFETFHNFOUFE

BOE
XJSF
TVSGBDF
USFBUNFOU




(bare/oxidised/enamelled)

Additional features:

r
-POHJUVEJOBM
XBUFS
CMPDLJOH
TZTUFN


r

4FNJDPOEVDUJOH
CJOEFS

(2) DESIGN OF THE INSULATION SYSTEM

The 2 basic Design drivers for designing the insulation system are:
(a) Electrical Gradients (b) Thermo-Mechanical & Thermo-Electrical Properties

(a) Electrical Gradients depend on:

t
*OUSJOTJD
SFMJBCJMJUZ
Life curve and reliability derivation


t
2VBMJmDBUJPO
DPWFSBHF
Type test and prequalification coverage (IEC 60840, IEC 62067,
Cigré Technical Brochure 303)

(b) Thermo-Mechanical &Thermo-Electrical Properties:

t
%JTTJQBUJWF
1PXFS
'BDUPS
UH
ɷ)
- Dielectrical losses = f (U²)
- Relative permittivity (ɸ)
Reactive power (power flows); charging current
(off load current, setting of protections)
- Temperature withstand
In continuous operation, in overload and short circuit

(3) DESIGN OF SCREEN / SHEATH REQUIREMENTS

The 2 basic Design drivers are:
(a) Mechanical Properties (b) Thermo-Electrical Properties

(a) Mechanical Properties:

t
#FOEJOH
DBQBCJMJUZ
MBZJOH
CFIBWJPVS

t
$PSF
QSPUFDUJPO
TIPDLT
QVODUVSFT
SBEJBM
XBUFS
UJHIUOFTT

t
'BUJHVF
UIFSNBM
DZDMJD
MPBEJOH

(b) Thermo-Electrical Properties:

t
4IPSU
DJSDVJU
DBQBCJMJUZ
*&$

*&$

$JHSÏ
5#


t
4DSFFO
MPTTFT
HFOFSBUFE
JO
"$
TZTUFNT

8
 Additional features

r Longitudinal water blocking system

r
0VUFS
TIFBUI
- Anti-corrosion protection
- Safety of personnel (induced voltages)
- Mechanical strength (abrasion during laying,
deformation in cleats)

- Special properties:
t
'MBNF
SFUBSEBODZ

-40)

t
"OUJUFSNJUF

BOUJSPEFOU
QSPQFSUJFT

t
67
QSPUFDUJPO

t
3FTJTUBODF
UP
IZESPDBSCPOT
BOE
TPMWFOUT

Anatomy of an EHV Cable

Normally, high voltage cables are characterised by the
presence of the following components:

r Conductor

r
4FNJDPOEVDUJOH
DPOEVDUPS
TDSFFO

r
*OTVMBUJPO
BMTP
DBMMFE
iEJFMFDUSJDu

r
4FNJDPOEVDUJOH
JOTVMBUJPO
TDSFFO

r
.FUBMMJD
TIFBUI
PS
TDSFFO

r
1SPUFDUJWF
PVUFS
DPWFSJOH

Each of these components is described in the following paragraphs:

Cable Components

CONDUCTORS

Conductors are made from copper or aluminium, using wires

or segments. Copper conductors are mainly used when a
high current carrying requirement is needed (typically
>1000 A) in addition to higher fault current. In case of
lower requirements, aluminium conductors are frequently
preferred due to the lower cost impact. Another important
parameter that has to be taken into account is the resistance
with alternating current. Because of the skin effect, the 'A.C.
resistance' of a conductor tends to be more significant as the
cross section increases. The skin effect forces the current
to flow along the peripheral areas, so the central section
of the conductor becomes less efficient. For this reason, a
special conductor construction, called 'segmental Milliken',
is used with big cross sections (from 1000 up to 2500 mm2).
The conductor is typically divided in 5 or 6 segments that
are slightly insulated from each other, so the current is
“constrained” to flow inside the segments.

Moreover, in order to obtain a further reduction of the skin

effect, it’s possible to oxidise or enamel a certain percentage A 400 kV cable
of the wires inside the segments. The 400 kV cable shown in with a Milliken Conductor
Figure has a Milliken Conductor.

Water blocking of the conductor is generally recommended in order to limit the water propagation along the
conductor in case of damage to the cable.

9
Insulation and semi-conducting screens

The main materials used for high voltage extruded cables are detailed below:

a) High Density Polyethylene (HDPE) is a thermoplastic material that was used for a limited period. Due to its
limitations with regard to its working and short circuit temperatures (respectively 80°C and 150°C), HDPE
insulation has been replaced by other extruded materials. HDPE has also been observed to have some
difficulties in handling the cables at low temperatures.

b) Ethylene Propylene Rubber (EPR) is a thermosetting compound and it is made from a blend of components,
which formulation can be modified in order to obtain specific characteristics. It is manufactured and offers good
performance in terms of “water treeing” resistance, as well as good elasticity characteristics. EPR has high
dielectric losses compared to XLPE and this has limited its use to the maximum voltage level of 150 kV. EPR
IBT
B
SBUFE
NBYJNVN
DPOEVDUPS
UFNQFSBUVSF
PG
¡$
BO
FNFSHFODZ
SBUJOH
PG
BQQSPY
¡$
BOE
B
DPOEVDUPS

short-circuit rating of 250°C.

c) Cross Linked Polyethylene (XLPE) is a thermosetting material. It offers a degree of purity higher than that offered
by the EPR and this makes this insulation a suitable material for applications up to 500 kV. Contrary to EPR
insulation, XLPE is very sensitive to moisture which would lead to its degradation. For this reason, it’s necessary
to prevent water penetration into the insulated core. This is achieved by applying a radial water barrier. XLPE
DBCMFT
IBWF
SBUFE
NBYJNVN
DPOEVDUPS
UFNQFSBUVSF
PG
¡$
BOE
BO
FNFSHFODZ
SBUJOH
PG
VQ
UP
BQQSPY
¡$

(depending on emergency time). The conductor shortcircuit rating is 250°C.

Figure shows a close-up of an XLPE cable and the

black semi-conducting screens can be seen on
each side of the XLPE insulation. Semi-conducting
screens are used on all high voltage cables from
6.6 kV onwards to ensure a smooth electrical
interface between conducting and insulating
regions. The stranded profile of the conductor
would initiate localised field concentration (i.e.
high stress areas) if interfaced directly with the
insulation and a consequent risk of ionisation and
ultimately electrical breakdown. Hence, provision
of semi-conducting screens removes these high
stress areas and provides uniform stressing at the
interface with the insulation.

To ensure a good interface, all three layers (i.e.

conductor screen, insulation and insulation screen)
are extruded in one process (triple extrusion). The
electrical properties for the various extruded type
insulations are detailed below:

A close-up of an extruded XLPE cable

Electrical
Tan Delta
Permittivity
Pe 0.001 2.3

EPR 0.005 3

XLPE 0.001 2.5

10
Metallic Sheath

While EPR cables up to 150 kV may be used without any metallic

barrier, it is recommended that all XLPE cables with rated
voltages higher than 60 kV are provided with a radial moisture
barrier comprising one of the following metallic sheaths:
t
&YUSVEFE
MFBE
TIFBUI
t
&YUSVEFE
DPSSVHBUFE
BMVNJOJVN
TIFBUI
$"4

t
4NPPUI
MPOHJUVEJOBMMZ
XFMEFE
BMVNJOJVN
TIFBUI
8"4

t
"MVNJOJVN
PS
DPQQFS
MBNJOBUFE
BOE
HMVFE
GPJM

The main functions of the metallic sheaths are:

t
1SPUFDUJPO
BHBJOTU
UIF
JOHSFTT
PG
NPJTUVSF
t
5P
HJWF
NFDIBOJDBM
QSPUFDUJPO
UIVT
QSFWFOUJOH
EBNBHF
BHBJOTU

external actions
t
5P
XJUITUBOE
UIF
TJOHMFQIBTF
GBVMU
DVSSFOU
t
5P
DBSSZ
UIF
DIBSHJOH
DVSSFOU
t
5P
QSPWJEF
UIF
FBSUI
PS
OFBSFBSUI
QPUFOUJBM
SFGFSFODF
GPS
UIF

cable insulation
Sometimes the above designs may be used in combination with
copper wires or aluminium wires in order to increase the short
circuit carrying capability. All the above sheathing methods
A lead sheathed XLPE cable
have advantages and disadvantages when compared towards
the following topics:
t
5IFSNBM
QFSGPSNBODF
t
&MFDUSJDBM
QFSGPSNBODF
t
$PSSPTJPO
SFTJTUBODF
t
8BUFS
SFTJTUBODF
t
.FDIBOJDBM
GBUJHVF
t
8FJHIU
t
&OWJSPONFOUBM
JNQBDU
Consideration of the optimum sheathing system will usually depend on the specific application and maybe also any
specific country requirements.

Outer Sheath
Generally PE (Polyethylene) is used as the sheathing material for buried cables. This is normally Medium-Density
Polyethylene (MDPE) or alternatively High Density Polyethylene (HDPE), both of which provide good mechanical
protection, good corrosion protection and good resistance to abrasion. PVC (Polyvinyl Chloride) may also be used
for buried cables. Cables laid in air (gallery, shaft, tunnel, etc.) normally have either a flame retardant PE or a PVC
sheath. Both systems are widely used.

11
12
HV & EHV PROCESS FLOW CHART

Lead/
Aluminum
HV AND EHV PROCESS FLOW CHART
 MANUFACTURING PROCES
OF HV XLPE CABLE

There are 3 types of EXTRUSION TECHNOLOGIES

CCV line (Catenary)

VCV line (Vertical)

MDCV line (Horizontal)

EHV Cable Accessories

ACCESSORIES FOR HIGH VOLTAGE POLYMERIC CABLES R&D EXPERTISE ACCESSORIES

FOR HIGH VOLTAGE POLYMERIC
OUTDOOR POLYMERIC TERMINATIONS CABLES
66 kV up to 400 kV

Silicone/ EPR one-piece

pre-moulded joints available
66 kV up to 400 kV
Several OHL connection
stalk design/ dimensions
Conical/ Cylindrical
insulator design

Arching horns
available on request

Transformer Terminations
66kV up to 400 kV

Different
filling medium

Several creepage
distance

GIS Terminations
66kV up to 400 kV

Optical fibres Partial discharge

management sensor port
on request on request

13
Bonding Systems
Where cable sheaths are bonded and earthed at both ends of a system, there is necessarily an induced circulating
current flowing through the sheaths and ground. This constitutes a power loss in the sheaths and therefore a
de-rating of the system current carrying capability. These solidly bonded systems are commonly used at High
Voltage level (up to 170 kV system). However, for the bulk power transmission requirements of most Extra High
Voltage systems (above 170 kV, up to 550 kV), and for some HV systems, it is essential to use a special bonded
system in order to realise the full rating capability of cables with large conductors.

Solidly Bonded System

The simplest and most common sheath bonding arrangement is termed “solid bonding”. Cable sheaths are bonded
and earthed at each end of the route, and possibly also at one or more intermediate joints for long route lengths.
Under normal (50/60Hz) loading conditions, a circulating current is induced in the sheath-earth loop generating
a power loss. This “sheath loss” therefore causes a reduction of the cable current carrying capability. The effect
is kept to a minimum by reducing mutual inductance between phase cables, i.e. cables are installed in touching
trefoil formation. Whilst cable proximity is thermally undesirable, it is more beneficial from the cable rating aspect
to minimise mutual induction and to accept greater mutual heating than for spaced cables.
For through-faults in the system, the return fault current to earth is shared by the three cable sheaths in parallel, since
the sheaths are bonded together at each end of the cable route. In case of an internal cable fault, the relevant short
circuit current flows along one cable sheath in the faulty cable length only and then sub-divides into three currents
at the first adjacent joint bay provided that the three sheaths are bonded together at this position.

Solidly Bonded System

Specially Bonded System

The basic principle of specially bonded systems is that of connecting the cable metallic sheaths in such a way
that circulating currents in the sheaths are either prevented or reduced to a minimum. The advantages of special
bonding over solid bonding are:

t
4IFBUI
MPTTFT
BSF
SFEVDFE
BOE
UIFSFGPSF
DBCMF
IFBUJOH
EVF
UP
TIFBUI
MPTTFT
JT
SFEVDFE

t
4NBMMFS
DPOEVDUPS
TJ[F
NBZ
CF
VTFE
PS
BMUFSOBUJWFMZ
B
IJHIFS
DVSSFOU
DBO
CF
DBSSJFE
CZ
B
HJWFO
DPOEVDUPS
TJ[F

t
$BCMFT
DBO
CF
MBJE
BU
SFMBUJWFMZ
XJEF
TQBDJOH
UIVT
JNQSPWJOH
IFBU
EJTTJQBUJPO
BOE
IFODF
BMMPXJOH
BO
JODSFBTF

in current rating or a further reduction in conductor size

t
3FEVDFE
DPOEVDUPS
TJ[F
SFTVMUT
JO
TNBMMFS
DIBSHJOH
DVSSFOU

14
The disadvantages of special bonding are:
t
5IFSF
JT
B
TUBOEJOH
WPMUBHF
PO
UIF
DBCMF
TIFBUI
BOE
PO
UIF
NBKPSJUZ
PG
KPJOUT
5IJT
WPMUBHF
NVTU
CF
MJNJUFE
UP
BO

agreed value by a suitable correlation between conductor current, phase spacing and cable section length
t
5SBOTJFOU
QIFOPNFOB
FH
TXJUDIJOH
PQFSBUJPOT
GBVMU
DPOEJUJPOT
BOE
MJHIUOJOH
JOEVDFE
TVSHFT

DBO
DBVTF
IJHI

voltages to appear across the sectionalising insulation and across the cable over sheath, and special steps
must be taken where necessary to limit these to acceptable levels
t
4NBMMFS
DPOEVDUPS
TJ[F
SFTVMUT
JO
JODSFBTFE
DPOEVDUPS
MPTTFT
t
*O
TJOHMFQPJOU
CPOEFE
TZTUFNT
JU
JT
VTVBMMZ
OFDFTTBSZ
UP
JOTUBM
B
QBSBMMFM
FBSUI
DPOUJOVJUZ
DPOEVDUPS
t
.BJOUFOBODF
UFTUT
BSF
SFDPNNFOEFE
PO
TIFBUI
WPMUBHF
MJNJUFST
CPY
DPNQSJTJOH
PG
TVQQPSU
JOTVMBUPST
MJHIUOJOH

arrestors etc in addition to the ingress protection test

Sheath Standing Voltage Limits

There isn’t any international standard on limits of sheath standing voltage under normal maximum loading
conditions. Some countries are rather conservative (e.g. 65V for HV systems and 150V for EHV systems are widely
used), others are allowing up to 400V, others have no limits providing that the part under voltage is not accessible.
At accessible positions (e.g. at terminations) components on which the induced voltage may rise to greater than
10V are commonly fitted with shrouds to prevent any accidental contact generated.
Single Point Bonded Systems
On relatively short cable routes which would normally require no joint or perhaps just one joint, the most practical
special bonding method is single point bonding. The cable sheaths in any one minor section are bonded and
earthed at one position only, usually (but not always) at one end of the cable route. Sheath circulating currents
are thus eliminated by leaving one end of the system unearthed or 'floating'. Under conditions of current
loading, the unearthed end of the cable sheath rises in voltage via induction and it is necessary to control this
voltage level under normal system operating conditions, during short circuits, and during transient overvoltages
(switching and lightning).
Where the overall route length causes an excessive standing voltage level, a single point bonding system may be
'repeated'. This arrangement is commonly used when there are two sections (for three sections Cross Bonding
System is used, ref. Clause 3.4). In such case, a 'Mid Point Bonding System' is used. Cable sheaths may be bonded
and earthed at the midpoint of the route only, with the sheaths rising in voltage at the terminations. Alternatively,
cable sheaths may be bonded and earthed at terminations, whilst at an intermediate point along the route the
sheath continuity is interrupted by an insulating barrier.

Single Point Bonded System

15
Normal System Loading

Under normal system loading conditions, the level of induced sheath voltage (standing voltage) is usually measured
in tens of volts and is determined by conductor current, cable dimensions, phase spacing, section length, and
earth conductor size and position. The voltage level is not harmful to the sheath insulation but is maintained within
limits set by utilities for the purpose of personnel safety.

Fault Conditions

Under through-fault conditions, the induced voltage level is determined by short circuit current. Maximum
acceptable levels of induced voltage are determined not by the sheath and joint insulation capabilities but by
the rated maximum power frequency voltage of sheath voltage limiters (SVLs) connecting the unearthed end of
each sheath to ground (refer to section 5.0 for SVL data). Under transient overvoltage conditions of lightning and
switching impulse, it is essential to limit the voltage level to which the cable sheath may be permitted to rise up
to. Specific concerns are (a) to protect the cable anti-corrosion covering, and (b) to limit the potential difference
across sectionalising insulation at the unearthed positions. For these reasons, non-linear resistors known as SVLs
(sheath voltage limiters) are connected between cable sheaths and earth at the floating ends of single point
bonded systems.

SVL units are not expected to withstand internal fault conditions (i.e. cable faults).

Earth Continuity Conductor

Since there exists no continuous sheath path to carry return fault current to earth, the standard practice in single
point bonded systems is to install a parallel earth continuity conductor (ECC) at a specified proximity to the power
cables. Also by transposing the ECC about the power cables at the midpoint of the section, voltage induction from
the power cables can be balanced, thus avoiding a permanent circulating loss in the ECC.

Cross Bonded Systems

On long cable systems beyond the scope of one or two single point bonded systems, cross bonding is normally
used to eliminate sheath circulating currents. An example of a cross bonded system is shown in Figure. This is
based on the principle that the induced voltages in the three phase cable sheaths are displaced vectorally by
120° (as per the conductor currents). It therefore follows that by cross connecting three sheaths of different phase
in series along the route, the vector sum of the induced voltages will be zero. If this is achieved, then circulating
current through cable sheaths will also be zero and sheath losses are reduced to eddy effects only.

The approach described pre-supposes that:

t
5IBU
UIF
DBCMF
SPVUF
DPNQSJTFT
UISFF
TFDUJPOT
PS
B
NVMUJQMF
PG
UISFF

t
&RVBM
NJOPS
TFDUJPO
MFOHUIT

t
"
CBMBODFE
USFGPJM
BSSBOHFNFOU

In practice, specially bonded systems are not often installed in trefoil formation since the rating benefits available
through spacing the cables apart to reduce mutual heating are usually also taken advantage of. In a cable section
installed in flat spaced formation, the voltage induced on the middle cable sheath is slightly less than in the
outer cable sheaths. This difference is eliminated by transposing each cable, conveniently at the joint positions.
At the terminations and at the ends of each major section, sheaths are usually solidly bonded and earthed.
Calculation methods are established in IEC 60287 to assess the effects of any imbalance caused by unequal
minor section lengths.

16
Except at the solid bond positions, the cable sheaths in a cross bonded system will rise in potential, the level
being determined by cable dimensions, conductor current magnitude, phase spacing, section length and position
of interest.

Systems are designed to limit sheath standing voltages within limits acceptable to customers (see section 3.2).
The distribution of sheath voltage along each section in a cross bonded system is relatively complex and is shown
in Figure below.
t
4PMJEMZ
CPOEFE
QPTJUJPOT
t
$SPTT
CPOEFE
QPTJUJPOT
t
.JOPS
TFDUJPO
t
.BHOJUVEF
PG
JOEVDFE
WPMUBHF
PO
DBCMF
TIFBUI

E (V)

Induced Voltage Distribution in Cross Bonded System

17
Fault Conditions

For through-fault conditions, the induced voltage level is

determined by short circuit current, cable dimensions,
phase spacing and section length, the voltage being
a maximum at the cross bond positions in a system of
balanced minor sections. Maximum levels of induced
voltage are determined by the ratings of SVLs connected
between cable sheaths and earth at cross bond positions.
Cross bonding arrangements at minor sectionalising
positions are shown in Figure.

Lockable link box with sheath voltage limiters

Sheath Voltage Limiter Characteristics

In specially bonded systems, the induced voltages generated across the cable oversheath are of course also
experienced by the sheath voltage limiter (SVL) units. The purpose of the SVL is to resist conduction under
conditions of normal service sheath standing voltage and also during temporary overvoltages caused by system
through faults (power frequency short circuit conditions). Conversely under transient overvoltage conditions of
switching and lightning, the SVLs are required to conduct to earth and thus to limit sheath voltages to within
levels safe for both the cable oversheath and the joint sectionalising insulation. SVL units as used on the earth
side of cable systems (screen/sheath) should not be confused with higher energy surge arresters more typically
connected to the high voltage side of power transmission plant.

The following parameters are typically considered for the selection of an SVL:

The rated voltage is the maximum design RMS power frequency voltage which can be applied across the terminals
of an SVL for a period of not less than one second, without causing damage. SVL units are type tested to withstand
two applications of rated voltage with a time interval between applications of between 10 and 15 seconds.

t
5IF
reference residual voltage is the voltage measured between the SVL terminals when an 8/20μs (8μs wave
front, 20μs duration) 10kA current impulse is applied.
t
5IF
reference voltage is the mean voltage as measured between the terminals when the SVL conducts +10mA
and -10mA (D.C.) at ambient temperature. SVL units appropriate for a particular system application are selected
during the evaluation of maximum induced sheath voltage during short circuit conditions. Sheath Voltage
Limiters as described above are usually enclosed in disconnecting Link Boxes. For particular applications, an
SVL unit having a low residual voltage rating is used. For cable terminations into separately earthed gas-
immersed switchgear, for example, it is essential to ensure that the sheath sectionalising insulation at the cable
termination is suitably protected against risk of flashover during switching operations. The sectionalising ring in
this case is usually bridged over with small-size SVLs, providing an open circuit during normal system operation
and a conduction path for transient overvoltages.

Fault Types

Two-phase to earth faults can give rise to higher voltages across the SVL than single-phase to earth faults, where
the terminal resistance is high. However, on the assumption that terminal earth resistance does not exceed 0.5
Ohms, the voltages are not greater than for the single-phase to earth fault. Three-phase to earth faults are not
the limiting condition for the SVL and need not be considered, except where the star point is unearthed. Phase
to phase faults free of earth are less onerous than the above and can be disregarded. As regards internal cable
faults, only single-phase to earth faults need be considered as two-phase to earth faults are highly unlikely with
single core cable systems.

18
Installation of EHV Cables and Accessories
Ravin Group supplies and installs high
voltage cables and systems on turnkey
packages. We provide our customers
with a comprehensive cable service
package which encompasses system
design, design and selection of cables
and compatible accessories, supply of
quality materials, installation, testing,
commissioning and finally ensuring full
safety and reliability of the installation.

Our installation team consists of a highly

qualified and experienced team of
engineers, who work with clients and
manufacturers to identify the quickest and
most cost effective power solutions. Our
team has been trained and experienced
in various countries around the world, and
they carry with them over 250 years of
cumulative experience in specialty jobs.
We have an experience of installation of
more than 150 km of EHV cables and 300
joints and terminations at voltages greater
than or equal to 220 kV.

We provide our customers with a

comprehensive cable service package
which encompasses system design
including design and selection of
cables and compatible accessories,
supply of quality materials, installation,
testing, commissioning and finally
ensuring full safety and reliability
of the installation.

Laying of EHV Cables

Direct Burial
Cable route shall be selected to avoid excess bending portions and to keep them as few as possible. It is
recommended that the bending radius at corners should be maintained at least a few times the minimum bending
radius, preferably more than 5 metres, as larger radius provides lower side wall pressure. Enough space shall be
maintained inside the cable trench. Furthermore, it shall be confirmed from available records of existing services
and utilities as well as with sufficient number of trial holes along the trench route, especially at joint bay locations,
that the trench route has no obstructions. It shall also be confirmed that no chemical agents, that could be harmful
to the cables, are present in the surrounding soil and water along the route. Always use a cable pulling winch.
When pulling cable mechanically by the pulling winch, the cabling winch rope is coupled to the cable by means
of the pulling eye. The pulling tension is thus transferred to the conductor. Pulling tension should not exceed the
maximum permissible pulling tension recommended by Ravin in their technical data.

19
 Cable Trench - Direct Burial Cable Trench - With Pipe

Cable Duct System

Larger bending radius is generally required in duct systems as compared to direct buried cable. Since
coefficient of friction of ducts is larger than that of cable rollers used in direct burial installation, resulting in higher
pulling tensions, consequently the maximum section lengths between joint bays is relatively shorter than that for
direct burial.

Therefore, each section length should be determined after careful calculation of the pulling tension and the
sidewall pressure of the corresponding section. Cable expansion from duct due to thermal expansion should also
be considered when dimensions of joint bays are determined. Offset arrangements should be envisaged to absorb
the thermal b ehaviour of the cable during its service life. For a single cable in a duct, the inner diameter of the
duct should be greater than at least two times the outer diameter of the cable being pulled. Internal surface of the
duct including the surface at joints shall be smooth and free from any defects such as protrusions, projections,
cracks, scratches, sharp edges etc., which may cause damage to cable outer sheath during pulling. Any sharp
edges at both ends of the duct should be rounded off and pipe collars provided at ends. The PVC pipe collar
should be installed at both ends of the ducts so as to prevent the duct edges from damage. Immediately prior
to the installation of the cable, the ducts shall be thoroughly cleaned using conduit cleaning devices to ensure
that any small pebbles, sand or other foreign material is removed before cable is installed. Use mandrels with a
diameter 6 mm less than the duct size to check for breaks or sharp edges in the duct that would damage the cable.
On completion of inspection, put the guide rope by blowing in to the pipe and connect to the winch pulling rope.

Each duct should be provided with a draw wire and both ends of the duct should be plugged in a proper manner
to prevent ingress of any foreign material like soil, sand, concrete, water etc. Only winch pulling shall be applied
for cable duct installation. The cabling winch rope is coupled to the cable by means of pulling eye. The pulling
tension is thus transferred to the conductor. The pulling tension should not exceed the maximum permissible
pulling tension recommended by Ravin in their technical data.

20
Lubrications of Cable

The use of cable lubricants, as the cables are pulled into ducts lessens the cable tensions and prevents any
scratching of cable jackets due to irregularities in ducts. A liberal use of lubricant is recommended for all pulling
operations. Only lubricants that are compatible with the outer sheath material (PVC, HDPE, and/or MDPE) shall be
used. Petroleum-based lubricant shall never be used for any formation with polyethylene jackets. The lubricant is
usually applied to the cable as the cable enters the duct or the feeding tube.

Cable Tunnel

Cable tunnel dimensions shall be so designed as to secure enough space both for settling of cables on supporting
structures and for installation and jointing works. The bending corners of the cable tunnel should also be designed
to provide the permissible bending radius to the cable with enough margins. When cables are laid on cable
racks or cable supports, they shall
then be fixed with cable cleats
or clamps at adequate intervals
to absorb the thermal expansion
and contraction with their lateral
or vertical movement within the
length between adjacent cleats. If
cables are laid without any binding,
they may move according to the
thermal behaviour and may drop
from the rack or supports. Further,
the metal sheath of the cable may
be subjected to excessive strain
at bent portions where the thermal
movement of the cable is partially
concentrated. In order to avoid this
movement, snake installation i.e.
laying the cable in uniform waveform,
is usually applied along the route on
racks or supports, to encourage the
absorption of the cable movement
smoothly. At the end of the cable
route, the cable ends should be set
straight and fixed with cable clamps
before rising to the sealing ends.

Special Construction

There may be many types of special constructions along the cable routes, such as river crossings, road crossings,
cable tunnel and cable bridges. Special care must be taken to lay cables at such locations. It is not possible
to list all countermeasures to cope with and cover every special construction; however, following are generally
recognised as the basic key points that should be taken into account:

a) The thermal environment must be satisfactory

b) Any thermo-mechanical forces that could be experienced must be adequately constrained or dissipated

c) Where cables are exposed to air, care must be duly taken of risks due to fire, vandalism, accidental damage by
third party. Cables must also be provided adequate protection against direct solar radiation

d) Exposure to vibration

e) Specified bending radius must be observed

21
Cable Laying

Most adequate method should be adopted to pull the cable considering site conditions, so as to avoid any damage
to the cable due to excessive mechanical forces experienced during cable installation and to ensure an efficient
installation. It must be ensured that the cable to be installed can be pulled without any damage or defect in
terms of cable pulling design according to route drawings and site conditions. Preliminary study shall be made to
determine proper cable laying method, direction of cable pull, arrangement of tools/equipment, communication
equipment, manpower and other necessary factors in order to achieve satisfactory cable installation. The most
effective method of pulling a high voltage cable is by nose pulling with a cable pulling eye fixed to the conductor.

Cable Pulling Design

In order not to damage the cable

during pulling, it is recommended
to pull the cable keeping both the
pulling tension and the sidewall
pressure lesser than the permissible
figures.

Data Of Cable Required

Following data on the cable is

required for cable pulling:

a) Overall cable diameter (mm)

b) Cross sectional area of

conductor (mm2)

c) Unit weight of cable (kg/m)

d) Material of conductor (copper /

aluminium)

Permissible Values

Permissible maximum value of pulling tension, which depends on the method of pulling, is decided by the criteria
as detailed under or that as recommended by Ravin:

Fmax = A. dmax

A = Conductor cross sectional are (mm2)

dmax = Maximum permissible stress (N/mm2)

= 50 N/mm2 for single core Copper Conductor

= 30 N/mm2 for single core Aluminium Conductor

22
Maximum Cable Pulling Tensions will be followed as per below table:

MAX. CABLE PULLING TENSIONS FOR HV CABLES

Cross Section & Construction Max. Pulling Tension for Copper Max. Pulling Tension for Aluminium
630 mm² XLPE 3150 kg 1850 kg
800 mm² XLPE 4000 kg 2100 kg
1000 mm² XLPE 5000 kg 3000 kg
1200 mm² XLPE 6000 kg 3600 kg
1600 mm² XLPE 8000 kg 4800 kg
2000 mm² XLPE 10000 kg 6000 kg
2500 mm² XLPE 12000 kg 7500 kg

Coefficient of friction
Following are the coefficient of friction between the cable outer sheathing and the rubbing surface during
laying process.
t
1VMMJOH
DBCMFT
PWFS
SPMMFST
ç




t
1VMMJOH
DBCMFT
UISPVHI
DPODSFUF
EVDUT
ç




t
1VMMJOH
DBCMFT
UISPVHI
DPODSFUF
EVDUT
- Grease Lubrication: μ = 0.15 - 0.25
- Water Lubrication: μ = 0.15 - 0.25
- Grease and Water Lubrication: μ = 0.10 - 0.20
If cables are to be pulled through long plastic pipes, it is essential that a lubricant be used. Otherwise, the heating
produced as a result of friction between the cable and the plastic surface could cause the thermoplastic sheathing
to stick to pipe walls.

Minimum Temperatures for Cable Laying

High Voltage Cable should not be laid at temperatures below -2°C.
In case, the cable must be laid at temperatures below -2°C, the cable must then be heated in special insulated
tents at 30°C - 40°C for 24 hours and then must be laid rapidly.

Cable Pulling Force Calculations

a) Horizontal/Flat Cable Pulling b) Sloping Cable Path Pulling
The pulling force (F) at the end of the cable path The pulling force (F) will be increased when laying
is given by: sloping up/uphill and decreased when laying
F = W.I.μ sloping down/downhill and is given by:
Where: W = Cable weight (kg/m) F = WI (μ cos b ± sin b)
I = Length of cable route / path (m) Where: b = angle of slope)
μ = Coefficient of friction + is used for uphill laying
- is used for downhill laying
On slopes up to approximately 20 deg. (36%), the
pulling force may be calculated by:
F = (W.I.μ) ± (W.h)
Where:
h = difference in level (mm)

23
c) Curved Cable Path

When the cable is pulled around a curve, the pulling force is increased by a factor (f), which is dependent on
the coefficient of friction (μ) and the angle of the bend (μ)

Fo = Fi x eμD

Fo = Force at exit of bend

Fi = Force at entry of bend

μ = Coefficient of friction

D = Bend angle in radians

Cable Laying Work

General Instructions:

This section describes general instructions to be observed during cable pulling work.

a) Handling of Cable

At the time of acceptance and prior to installation, the cable reel should be thoroughly examined for any outside
physical damage or damage to cable end caps. This examination should also include lagging, reel flanges and
reel marking, tags and labels. While handling cables, necessary precaution should be taken to prevent damage
to the cables.

Cable reels that are to be transported on trucks must be securely blocked or anchored to prevent rolling. If a reel
of cable is to be rolled for any appreciable distance, it shall be rolled in the direction indicated by the arrow on the
reel flange or with the outside end of cable trailing, if not marked, so as not to loosen the turns of cable on the reel.
When rolling reels on the ground, they shall be carefully eased over any rough surfaces. Care shall be taken to
avoid damaging reel lagging in order that outer layer of cable remains protected. In removing lagging from cable
reels, care shall be taken not to damage the cable. Remove all nails, staples or bolts from inside flange before
unreeling cable. Care is to be taken to prevent cable from dragging.

24
Before Cable Pulling
t
*U
TIBMM
CF
DPOmSNFE
UIBU
USFODI
nPPS
PS
PUIFS
QMBDFT
XIFSF
UIF
DBCMF
JT
UP
CF
JOTUBMMFE
BSF
GSFF
GSPN
BOZ
GPSFJHO

materials such as stones, nails and pieces of concrete, asphalt, brick pieces, glass pieces, sharp-edged
objects etc., which may damage the cable. Such materials should be removed at least 30 cm away from
the trench. Any water inside the trench should be pumped out completely. The trench wall must be secured
appropriately in accordance with specification prescribed by the client. The cable trench curves must be
checked thoroughly, to ensure that the minimum bending radius of the cable is attained. Sweet sand (or backfill
soil as required by project specifications) shall be evenly distributed on the trench floor with minimum thickness
of 150 mm or to a thickness prescribed in the project specifications.
t
1SJPS
UP
TUBSU
PG
DBCMF
QVMMJOH
3BWJO
SFDPNNFOET
UP
DPOEVDU
UIF
%$
TIFBUI
UFTU
PO
UIF
SFFM
JO
PSEFS
UP
FOTVSF

that no damage has taken place during transporting and handling of the cable. Upon completion of the test
heat shrinkable end caps, to protect against ingress of water or foreign particles, must immediately seal the
exposed area. Whenever a cable is cut, the exposed end shall be sealed to protect from rain, mist or dripping
or splashed water by heat shrinkable caps. The drum should be mounted on transport and laying trailer. For
cable pulling, the cable drum shall be set at the opposite direction to the arrow painted on the drum that
indicates the direction of rolling during transportation. Care should be taken not to damage the cable by battens
when removing them from the cable drum. The direction of pulling should be so chosen so as to require the
least pulling strength at the end of the cable path.
t
3FMJBCMF
DPNNVOJDBUJPO
CFUXFFO
UIF
ESVN
UIF
IFBE
PG
DBCMF
PO
DVSWFT
FOUSBODF
UP
EVDU
JOUFSNFEJBUF
QPTU

and the winch has to be established to effectively coordinate the work process. The equipment to be used
should be of proven reliability and should be thoroughly tested before cable installation begins. Ensure that the
winch has a pulling recorder and a tension meter, to continuously monitor the cable pulling force. It should not
exceed the maximum pulling force of the cable recommended by Ravin.
t
&TTFOUJBM
XPSET
PS
TJHOBMT
GPS
DBCMF
QVMMJOH
BU
MFBTU
45"35
BOE
4501
BSF
mYFE
BOE
VOEFSTUPPE
CZ
BMM
UIF

associated staffs.
The meeting prior to cable pulling is recommended to decide position of watchmen with communicative
equipment to guide cable pulling works. Watchmen shall be positioned every 50 metres and at every corner.
t
*U
TIBMM
CF
DPOmSNFE
UIBU
DBCMF
ESVN
ESVN
CSBLF
XJODI
SPMMFST
XJSF
SPQF
ESVN
GPS
XJSF
SPQF
BOE
BOZ
PUIFS

necessary tools/equipment have been set properly. Swivel shall be installed between wire rope and pulling
eye to prevent the cable from twisting. At the entrance to the cable trench, a cable guiding and bearer stand is
positioned, over which the cable taken off the cable drum is pulled into the trench. The rollers that are inclined
towards the centre ensure that the cable is fed centrally into the trench. The rule for curves in the trench is that
under no circumstances should they fall below the minimum prescribed bending radius of the cable (15 x ØD
of cable). The cable rollers in straight portions shall be set at approximately 2 metre intervals to avoid the slack
of the cable pulling. Whereas the cable rollers in bend portions shall be set as close as possible, so as not to
be subjected to the sidewall pressures partially. Sufficient numbers of corner cable rollers are positioned on the
curves in the trench, to prevent cable sliding off. In-field practice anchor pins have proved ideal for anchoring
the corner rollers.
t
'JOBM
DIFDL
PG
USFODI
TIBMM
CF
DBSSJFE
PVU
TP
BT
UP
FMJNJOBUF
UIF
SJTLT
UIBU
NBZ
EBNBHF
UIF
DBCMF
"OE
JU
TIBMM

be confirmed that trench will not collapse at any portion along the cable route. Timbering/Shuttering shall be
provided securely prior to cable pulling at positions where trench mayor is liable to collapse.
t
8IFO
UIF
DBCMF
JT
QVMMFE
JOUP
TIBGU
PS
JODMJOFE
UVOOFM
TVGmDJFOU
DBQBDJUZ
PG
CSBLF
GBDJMJUJFT
TIBMM
CF
BQQMJFE
TP

that the cable may not slip down due to its weight.

During Cable Pulling

t
.BYJNVN
QVMMJOH
TQFFE
TIBMM
CF

NNJO
5IF
QVMMJOH
TQFFE
TIBMM

be reduced at corners, inlets of duct, etc. where the smooth pulling
may be blocked. After confirming that no damage has occurred at
these portions, the pulling tension may be increased. Necessary
action should be taken to eliminate the cause of damages, in case
of its occurrence.
t
8BUDI
UIF
DBCMF
PO
UIF
DBCMF
SPMMFST
FTQFDJBMMZ
BU
CFOE
QPSUJPOT

and maintain sufficient clearance between existing services and
the cable along the whole cable route all the time during cable
pulling..

25
t
5IF
QVMMJOH
UFOTJPO
BOE
UIF
TJEFXBMM
QSFTTVSF
TIPVME
OFWFS
FYDFFE
UIF
QFSNJTTJCMF
WBMVFT
*U
JT
FTTFOUJBM
UP
CF

able to control the speed of pulling by monitoring pulling force speed and the length.
These parameters should be recorded continuously on a recorder, which is an indication and proof of the
correct laying. When pulling force exceeds the maximum permissible setting, the pulling should stop.
t
5IF
PVUMPPL
PG
UIF
DBCMF
TIBMM
CF
DIFDLFE
BOE
JU
TIBMM
CF
DPOmSNFE
UIBU
UIF
DBCMF
IBT
OPU
CFFO
EBNBHFE

during cable pulling. The cable pulling should be stopped immediately on finding any damage and should not
be resumed until the causes are removed. The damage portion of cable shall be repaired as required.
t
8IFO
UIF
JOOFS
FOE
PG
UIF
DBCMF
PO
UIF
DBCMF
ESVN
JT
MPPTFOFE
EVSJOH
DBCMF
QVMMJOH
JU
TIBMM
CF
UJHIUFOFE
BHBJO

to the cable drum.

After Cable Pulling t
/FDFTTBSZ
QSPUFDUJPO
UP
UIF
DBCMF
TIBMM
CF

t
5IF
PVUMPPL
PG
UIF
DBCMF
TIBMM
CF
DIFDLFE
XIFUIFS
provided against mechanical damage, vandalism
the cable has been damaged or not. Any damage and any other possibility to damage the cable. It
shall be repaired in a proper manner after careful is recommended to backfill the trench as soon as
examination. possible and not to leave the cable exposed.
t
*OUFHSJUZ
PG
BOUJDPSSPTJWF
TIFBUI
TIBMM
CF
DPOmSNFE
t
5IF
DBCMF
FOE
TIBMM
CF
SBJTFE
VQ
IJHIFS
UIBO
UIF

by carrying out DC high voltage test on it before and maximum water level expected. The integrity of
after backfilling. sealing at the cable ends shall be confirmed to
prevent water or any moisture entering the cable.
Immediately after the first phase of backfilling and
Repair work shall be carried out if necessary.
prior to final backfilling, DC sheath test at 10 kV for
1 minute should be conducted to ensure that no t
1PXFS
DBCMFT
BOE
BVYJMJBSZ
DBCMFT
TIBMM
CF
BSSBOHFE

damage has occurred to the cable sheath during so as to keep the specified distance between them,
cable pulling. Upon completion of the test heat in order to maintain the current rating capacity and
shrinkable end caps to protect against ingress of to limit sheath current/sheath induced voltage of the
water or any foreign particles, must immediately cable and induced voltage on auxiliary cables as
seal the exposed area. per designed values.

We have an impressive client list pan-India. Some of the jobs which we have undertaken are as follows:

Completed Jobs
Year of
Client Voltage Type of Job
Execution
Reliance Power - Samalkot 400 kV 2012 Installation of terminations
Supply of Cable, and accessoriesLaying of cable and Installation of
NTPC - SAIL - L & T 220 kV 2006-07
accessories (18 terminations and 4 kms cable)
Supply of Cable, and accessoriesLaying of cable and Installation of
Reliance Infrastructure Ltd. 220 kV 2007-08
accessories (54 nos terminations, cable 4 kms)
Uttam Galwa Wardha factory 220 kV  Supply of accessoriesJointing and termination services

Siemens 220 kV 2010 Supply of accessoriesJointing and termination services

Supply of Cable, and accessoriesLaying of cable and Installation of
Reliance Infrastructure Ltd. 220 kV 2010-12
accessories (54 km cable and 210 joints and terminations)
Supply of Cable, and accessoriesLaying of cable and Installation of
Vardhman Group 220 kV 2012 - 13
accessories (30 nos joints and terminations, cable 4.8 kms)
Dhaka Electric 132 kV 2008 Jointing in Oil filled cable for Dhaka Electric

Mahagenco, Vaitarna 132 kV  Supply of accessoriesLaying of cable (3kms) and installation of accessories
Supply and installation of accessories, Shifting of existing cable and
Mahatransco, Vasai 110 kV 
installation of accessories
Crompton Greaves 66 kV 2008 Installation of GIS terminations for Torrent Power in Surat

Iljin Electric 66 kV 2008 Installation of outdoor terminations for MRVCL

Universal Cables 66 kV 2008 Installation of outdoor terminations for MRVCL
Reliance 66 kV 2005 onwards Call centre operations for jointing services

26
Pictures of some key and difficult locations

Gorai Towers of Reliance Infrastructure:

Before Project Start

After Project Completion

27
Goregaon Towers of Reliance Infrastructure:

Cable Installation on Ladders

After Project Completion

28
After Project Completion

29
Table No.1: Reference Test Voltages for EHV Cables

Highest
15 min Power
Rated Voltage for
30 min Partial Tan delta Heating Impulse Frequency
Voltage of equipment
Voltage test Discharge measurement Cycle test Withstand Voltage test
Cables Between
6P
UFTU
6P
6P
6P
test after impulse
6P6
Conductors
UFTU
6P

6N

kV kV kV kV kV kV kV kV

38/66 72.5  57 38 76 325 

64/110 123 160  64 128 550 160

76/132 145  114 76 152 650 

127/220* 245 315  122 254 1050 315

5FTU
7PMUBHFT
BSF
HFOFSBMMZ
JO
MJOF
XJUI
*&$


*4
1BSU


Table No. 2: Conductor Resistance

Max DC resistance of App. AC resistance of

Cross- Conductor at 20oC Conductor at 90oC
Sectional Area of
Conductor
TR
NN
Aluminium Copper Aluminium Copper
conductor conductor conductor conductor
(Ohm/km) (Ohm/km) (Ohm/km) (Ohm/km)
 0.3200  0.4110 0.2460
120 0.2530 0.1530 0.3250 
150 0.2060 0.1240 0.2640 
185 0.1640  0.2110 0.1270
240 0.1250 0.0754 0.1610 
300 0.1000 0.0601  0.0780
400 0.0778 0.0470 0.1010 0.0618
500 0.0605 0.0366  
630  0.0283 0.0622 
800 0.0367 0.0221  0.0322

1000  0.0176 0.0380 0.0236

1200 0.0247 0.0151 0.0326 0.0207

1600 0.0186 0.0113 0.0251 0.0163

2000   0.0207 0.0138

30
Table No. 3: Conductor Short Circuit Rating

Cross Sectional area 4IPSU
$JSDVJU
3BUJOH
GPS

4FD

NJO
7PMUBHF
UFTU
6P

PG
$POEVDUPS
4R
NN

AlkA (rms) CukA (rms)

  13.58

120 11.30 17.16

150 14.10 21.45

185 17.40 26.45

240 22.60 34.32

300 28.20 

400 37.60 57.20

500 47.00 71.50

630  

800 75.20 114.40

1000  143.00

1200 112.80 171.60

1600 150.40 228.80

2000 188.00 286.00

Table No. 4: Minimum Conductor Cross-sections and Insulation Thickness

Smallest Nominal Nominal

7PMUBHF
(SBEF
L7
Conductor cross-section Thickness of Insulation

(Sq.mm.) (mm)

38/66  11.0

64/110 150 16.0

76/132 185 18.0

127/220 400 27.0

Note:
"CPWF
WBMVFT
BSF
BT
QFS
*4
1BSU


31
Table No. 5: Capacitance of Cable (μf/Km)

Cross- Voltage grade of Cable

Sectional Area of
$POEVDUPS
4RNN

38/66 kV 64/110 kV 76/132 kV 127/220 kV

 0.150
120 0.160
150 0.170 0.135
185 0.180 0.140 0.130
240  0.150 0.140
300 0.210 0.165 0.150
400 0.230 0.175 0.165 0.125
500 0.250  0.175 0.135
630 0.275 0.205  0.145
800 0.300 0.225 0.205 0.155
1000 0.325 0.245 0.225 0.170
1200 0.360 0.270 0.245 0.185
1600 0.400  0.270 0.200
2000 0.445 0.325 0.300 0.220

Table No. 6A: Current Rating of EHV Single Core 66kV Cable

Single Point Bonding/Cross Bonding

Cross-
Sectional
Trefoil Formation Flat Formation
Area of
Conductor In Ground In Air In Ground In Air
4RNN

Aluminium Copper Aluminium Copper Aluminium Copper Aluminium Copper

(Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp)
  250 271  202 261  380
120 221 383 312 401 230  341 438
150 246 316 352 452 257 331 385 
185 277 354 402 515  372 440 566
240  407 471 602 335   666
300 358 455 537 685 377 483  762
400 408 513 624  431 548  882
500 462 576 722   620 806 10021
630 523 644 835 1033 560 701  
800 585 708  1161 632 781 1080 1341
1000 686 816 11111 1372 723  1264 
1200 722 871 12 235 1503   1416 1763
1600 815  1434 17716  11108  2055
2000  1038 1613 
 1008 12 216  2317

Note: The above current ratings correspond to a metallic sheath/screen short circuit current capability of
31.5 kA. For one second duration. For any variation from this value of short circuit current and duration, kindly
refer to us.

32
Table No. 6B: Current Rating of EHV Single Core 66 kV Cable

Both End Bonding

Cross-
Sectional Trefoil Formation Flat Formation
Area of
Conductor In Ground In Air In Ground In Air
4RNN

Aluminium Copper Aluminium Copper Aluminium Copper Aluminium Copper

(Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp)

  242 267 341  234 284 357

120 215 272 307  211 258 324 404
150  301 345 437 231 281 362 
185 267 334   255 305 408 501
240 305 378 456 571 284 335  570
300  417 516 642   524 
400 380 461  728 337 384  
500 424 507 678 821 365 407 662 767
630 471 554 772    737 837
800 516  866 1013 415 447 806 
1000 554 631  1115 437 465 884 
1200 587 660 1048  453 477  1032
1600  704 1176 1317 474  1030 1105
2000 678 736 1285 1415  505 1101 1166

Table No. 7A: Current Rating of EHV Single Core 110/132 kV Cable

Single Point Bonding/Cross Bonding

Cross-
Sectional Trefoil Formation Flat Formation
Area of
Conductor In Ground In Air In Ground In Air
4RNN

Aluminium Copper Aluminium Copper Aluminium Copper Aluminium Copper

(Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp)

185 277 354  510  371  551

240  407 467  335  505 
300 358 456 533 680 377 483 578 742
400 408 514 618 783 431 548 673 
500 463 577 715   620 783 
630 523 646 826 1027 560 701  1145
800 586 712  1155 632 782 1046 1302
1000 666 817  362 723  223 1544
1200 721 873     368 1708
1600 816  1417 707  1108 1612 
2000  1043   1007 1217 1838 2247

Note: The above current ratings correspond to a metallic sheath/screen short circuit current capability of
31.5 kA. For one second duration. For any variation from this value of short circuit current and duration, kindly
refer to us.

33
Table No. 7B: Current Rating of EHV Single Core 110/132 kV Cable

Both End Bonding

Cross-
Sectional
Trefoil Formation Flat Formation
Area of
Conductor In Ground In Air In Ground In Air
4RNN

Aluminium Copper Aluminium Copper Aluminium Copper Aluminium Copper

(Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp)

185 268 336   256 308 403 

240 306 381 455 574 286 338 465 570
300 341 421 516 646 312 363 521 632
400 383 466  735 341   705
500 428 513  830  414 664 778
630 475 561 775   436 741 853
800 522 605 871 1030 420 454 815 
1000    1138 443 473  1003
1200  668 1057 1222  485  1060
1600 645 713  1347 480 500 1050 1137
2000 685 746 1303   512 1123 1200

Table No. 8A: Current Rating of EHV - Single Core 220 kV Cable

Single Point Bonding/Cross Bonding

Cross-
Sectional Trefoil Formation Flat Formation
Area of
Conductor In Ground In Air In Ground In Air
4RNN

Aluminium Copper Aluminium Copper Aluminium Copper Aluminium Copper

(Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp)

400 406 513 608 771 430 546 651 831

500 461 576 703 885   756 
630 522 645 811 1212 558  878 1106
800 585 712  1141 630 780  1258
1000 664 815 1077 1342 720  1178 
1200 718 870  1470 785  1316 1647
1600   1386 1678  1101 1546 
2000  1010 1544 1833   1756 2147

Note: The above current ratings correspond to a metallic sheath/screen short circuit current capability of
31.5 kA. For one second duration. For any variation from this value of short circuit current and duration, kindly
refer to us.

34
Table No. 8B: Current Rating of EHV - Single Core 220 kV Cable

Both End Bonding

Cross-
Sectional
Trefoil Formation Flat Formation
Area of
Conductor In Ground In Air In Ground In Air
4RNN

Aluminium Copper Aluminium Copper Aluminium Copper Aluminium Copper

(Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp) (Amp)

400 384   734 344  585 706

500  518 674 831 373  660 784
630 478 566 770  400 442 740 862
800 525 612  1038 425 461 818 
1000 562 646  1152 448 480  1024
1200  674  1237 465   1085
1600 643 713 1188 1358  516 1071 1174
2000 670 728 1286 1440 537 561 1186 1288

Note: The above current ratings correspond to a metallic sheath/screen short circuit current capability of 31.5 kA.
For one second duration. For any variation from this value of short circuit current and duration, kindly
refer to us.

Table No. 9: Rating factors for variation in ambient air temperature

Air
temperature 15 20 25 30 35 40 45 50 55 60
(oC)

Conductor
5FNQ
¡$ 1.25 1.2 1.16 1.11 1.05 1  0.88 0.82 0.76
Rating Factors

Table No. 10: Rating factors for variation in ground temperature

Air
temperature 15 20 25 30 35 40 45 50
(oC)

Conductor
5FNQ
¡$ 1.12 1.08 1.04 1   0.87 0.82
Rating Factors

35
Table No.11: Rating factors for grouping of single core cable laid directing round in horizontal formation

Distance
between
Number of circuits in group
centres
of circuits

mm 1 2 3 4 5 6 7 8 
100 1 0.76 0.67  0.55 0.51  0.47 0.46
200 1 0.81 0.71 0.65 0.61 0.58 0.56 0.53 0.52
400 1 0.85 0.77 0.72  0.66 0.64 0.63 0.62
600 1 0.88 0.81 0.77 0.74 0.72 0.71 0.7 
800 1  0.84 0.81  0.77 0.76 0.75 0.75
2000 1        

Table No.12: Rating factor for thermal resistivity of soil

Soil thermal
resistivity 70 100 120 150 200 250 300
(Deg. C cm/Watt)

Rating factor 1.36  1.11 1 0.88 0.78 0.73

Table No.13: Rating factor for depth of laying

Depth of
 100 120 150 160 170 180  200
laying (cm)

Rating factor 1.06 1.05 1.03 1     

Table No.14: Rating factor for phase spacing in flat formation

Phase
D D+70 D+200 D+250 D+300 D+350 D+400
Spacing (S) (Cm)

Rating factor  1 1.03 1.05 1.07 1.08 1.1

Note: D is the overall diameter of cable.

36